Dell™ PowerEdge™ Systems Oracle Database 10g Release 2 Enterprise Edition Real Application Cluster for Microsoft® Windows Server® 2003 Standard and Enterprise x64 R2 Edition Deployment Guide Version 1.1 w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes and Notices NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. ___________________ Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Contents Software and Hardware Requirements License Agreements . . Important Documentation . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . 7 7 . . . . . . . . . . . . . . . . . . . . . . . Installing and Configuring the Operating System . . . . . . . . . . . . . . Installing the Operating System Using the Deployment CDs Verifying Cluster Hardware and Software Configurations 7 . . . . . . . . . . 9 . . . . 9 12 . . . . . . . .
Installing the Latest Oracle Patches . . . . . . . . . . . . Installing the Patch for Split Brain Issue During System Boot Configuring the Listener . . . . . . . . . . . . . . . . . . Creating the Seed Database . . . . . . . . . . . . . . . . Additional Information . . . . . . . 36 36 37 37 . . . . . . . . . . . . . . . . . . . . . . . . . . 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 . . . . . . . . . . . . 41 42 45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This document provides information for installing, configuring, reinstalling, and using your Oracle Database 10g R2 software following Dell’s Supported Configurations for Oracle. Use this document in conjunction with the Dell Deployment CD to install your software. If you install your operating system using only the operating system CDs, the steps in this document may not be applicable. The following topics are covered: • Software and hardware requirements.
Software and Hardware Requirements Table 1-1 lists basic software requirements for Dell’s Supported Configurations for Oracle. Table 1-2 lists the hardware requirements. For detailed information on the minimum software versions for drivers and applications, see "Supported Software Versions." Table 1-1. Software Requirements Software Component Configuration Microsoft Windows Server 2003 Standard/Enterprise x64 R2 Editions Oracle10g R2 Version 10.2.0.
License Agreements NOTE: Your Dell configuration includes a 30-day trial license of Oracle software. If you do not have a license for this product, contact your Dell sales representative. Important Documentation For more information on specific hardware components, see the documentation included with your system.
6 At the command prompt, type 3 to select Oracle 10g R2 EE On Windows Server 2003 x64 R2 SE/EE and press . 7 At the command prompt, type 1 and press to select the option to copy the solution by the Dell Deployment CD. 8 When prompted, remove the Dell Deployment CD1 from the CD drive and insert the Dell Deployment CD2 into the CD drive. 9 When prompted, insert the Microsoft Windows Server 2003 x64 R2 CD1 into the CD drive.
4 At the command prompt, type echo %Tmp% and press . The following path appears: %SystemDrive%\Tmp where %SystemDrive% is the user’s local drive. Verifying Cluster Hardware and Software Configurations Before you begin the cluster setup, ensure that the hardware installation, public and private interfaces, and the node software are configured correctly. The following sections provide information about Fibre Channel cluster setup.
Table 1-4.
System Hardware and Software Configurations • • • Each node must include the following minimum hardware peripheral components: – Two hard drives (73 GB minimum) in the internal hard-drive bay – Three Gigabit NIC ports – Two HBAs (one dual-port HBA in case of PowerEdge 1850 and 1950 systems) Each node must have the following software installed: – Windows Server 2003, Standard/Enterprise x64 R2 Edition (see Table 1-1) – HBA driver The Fibre Channel storage must be configured with a minimum of th
Cabling Your Storage System for a SAN-Attached Configuration Figure 1-2.
Use the following procedure to configure your Oracle cluster storage system in a four-port, SP SAN-attached configuration. 1 Connect one optical cable from SP-A port 0 to Fibre Channel switch 0. 2 Connect one optical cable from SP-A port 1 to Fibre Channel switch 1. 3 Connect one optical cable from SP-B port 0 to Fibre Channel switch 1. 4 Connect one optical cable from SP-B port 1 to Fibre Channel switch 0. 5 Connect one optical cable from HBA0 on node 1 to Fibre Channel switch 0.
Configuring and Teaming the Private Network Before you deploy the cluster, assign a private IP address and host name to each cluster node. This procedure ensures that the nodes can communicate with each other through the private interface. Table 1-7 provides an example of a network configuration for a two-node cluster. NOTE: This example assumes all the IP addresses are registered in the hosts file of all cluster nodes. Table 1-7.
k In the Team Properties window, click OK. l In the Intel NIC's Properties window, click OK. m Close the Computer Management window. 4 If node 1 is configured with Broadcom NICs, configure NIC teaming by performing the following steps. If not go to step 5. a Click Start → Programs→ Broadcom→ Broadcom Advanced Control Suite 2 The Broadcom Advanced Control Suite 2 window appears. b Click Tools and select Create a Team. The Broadcom Teaming Wizard window appears. c Click Next.
Configuring the IP Addresses for Your Public and Private Network Adapters NOTE: The TOE functionality of TIE–capable NIC is not supported in this solution. 1 Update the adapter’s network interface name, if required. Otherwise, go to step 3. a On node 1, click Start and navigate to Settings→ Control Panel→ Network Connections. b In the Network Connections window, right-click the public network adapter you want to rename, and select Rename.
d Ensure that the network adapters are listed in the following order: Public Private NOTE: Click the up and down arrows to change the adapter order. e Click OK. f Close the Network Connections window. 4 On both nodes, add the public, private, and virtual IP addresses and host name to the %SystemRoot%\system32\drivers\etc\hosts file. NOTE: Add the public and virtual IP addresses to the hosts file only if they are not registered with the DNS server.
Installing the Host-Based Software Required for Dell|EMC Follow the procedures in your Dell|EMC documentation to install the EMC Navisphere® Agent software that came with your Dell|EMC system. Verifying the Storage Assignment to the Nodes 1 On the Windows desktop, right-click My Computer and select Manage. 2 In the Computer Management window, click Device Manager. 3 Expand Disk drives.
4 In the left window pane, expand Storage Arrays. 5 Click the storage system identifier. The storage system storage processors appear in the right window pane. 6 In the left pane, click the first SP. 7 In the SP Configuration window, ensure that all paths are configured as follows: • In the State column, the state is Alive. • In the Mode column, the mode is Active. 8 Repeat step 6 and step 7 for the remaining SP. 9 Close the PowerPathAdmin console.
3 Right–click on the partition area of the first shared disks assigned to the cluster nodes and select New Partition. The Welcome to the New Partition Wizard appears. 4 Click Next. 5 In the Select Partition Type window, select Extended partition and click Next. 6 In the Specify Partition Size window, accept the default partition size and click Next. 7 Click Finish. The disk partition area you selected in step 3 is configured as an extended partition.
Preparing the Database Disk and Flash Recovery Area for Database Storage With OCFS This section provides information for creating logical drives that will be used to create the Oracle’s Clustered File System (OCFS) storage disk. NOTE: If you are creating the logical drives that are used to create the Automatic Storage Management (ASM) storage disk, ignore the following steps and see "Preparing the Database Disk and Flash Recovery Area for Database Storage With ASM.
Preparing the Database Disk and Flash Recovery Area for Database Storage With ASM This section provides information about creating logical drives that will be used to create ASM disk storage. ASM disk storage consists of one or more disk groups that can span multiple disks. NOTE: If you are creating the logical drives that are used to create the OCFS storage disk, ignore the following steps and follow the procedures in "Preparing the Database Disk and Flash Recovery Area for Database Storage With OCFS.
Enabling the Automount Option for the Shared Disks 1 On node 1, click Start and select Run. 2 In the Run field, type cmd and click OK. 3 At the command prompt, type diskpart and press . 4 At the DISKPART command prompt, type automount enable and press . The following message appears: Automatic mounting of new volumes enabled. 5 At the DISKPART command prompt, type exit and press . 6 Close the command prompt. 7 Repeat step 1 through step 6 on each of the remaining nodes.
3 Click Next. 4 In the Specify Home Details window, accept the default settings and click Next. NOTE: Record the OraCR10g_home (CRS Home) path because you will need this information later. 5 In the Product Specification Prerequisite Checks window, make sure all the checks are completed successfully and then click Next. 6 In the Specify Cluster Configuration window, enter the following: • An alternate cluster name (if desired). • The public and private network host names for both cluster nodes.
12 In the Cluster Configuration Storage window, perform the following steps for the database: a Locate the partition created in step 1 of "Preparing the Database Disk and Flash Recovery Area for Database Storage With OCFS." b Select the partition and click Edit. c In the Specify Disk Configuration window, select Format partition with CFS. d Ensure that the Use partition for data storage is selected.
Changing the css misscount Value 1 Shutdown all nodes except node 1. 2 On node 1, open a command prompt window. 3 At the command prompt, type the following and then press : cd %ORA_CLUSTERWARE_HOME%\bin\ where %ORA_CLUSTERWARE_HOME% is the home directory that you created in step 4 in "Installing Oracle Clusterware Version 10.2.0.1." 4 At the command prompt, type the following and press : crsctl set css misscount 120 5 Restart node 1 and login as administrator. 6 Start all other nodes.
5 In the Specify Home Details window under Destination, verify the following: • In the Name field, the Oracle database home name is OraDb10g_home1. • In the Path field, the complete Oracle home path is %SystemDrive%\oracle\product\10.2.0\db_1 where %SystemDrive% is the user’s local drive. By default OUI chooses one of CFS shared drive for copying the database files. Change the drive to the %SystemDrive% by changing the drive letter in the Path field.
Installing Patchset 10.2.0.2 for Oracle 10g Clusterware Before you Begin 1 Stop the nodeapps on all the nodes: %SystemDrive%:\%CRS_HOME%\bin> srvctl stop nodeapps -n where %SystemDrive% is the user’s local drive. 2 Stop all the oracle services on all the nodes. Patchset Installation Steps NOTE: You must install the patchset software from the node where the Oracle RAC 10g R2 software was installed.
4 In the Specify Hardware Cluster Installation Mode window, click Next. 5 In the Summary window, click Install. During the installation the following error message may appear, Error in writing to file oci.dll. To work around this issue, perform the following steps: a Cancel the patchset installation. b Rename the %Oracle_home%\BIN directory to \bin_save. c Reboot the system. d After the reboot, rename the \bin_save file to \bin. e Run the setup.exe file from the patchset folder.
5 In the Welcome window, select Listener configuration and click Next. 6 In the Listener Configuration, Listener window, select Add and click Next. 7 In the Listener Configuration, Listener Name window in the Listener name field, accept the default setting and click Next. 8 In the Listener Configuration, Select Protocols window, in the Selected protocols field, select TCP and click Next. 9 In the Listener Configuration, TCP/IP Protocol window, select Use the standard port number of 1521 and click Next.
11 In the Database File Locations window, select the location for storing database files: a Select Use Common Location for All Database Files. b Click Browse. c In the Directory Browse window, use the pull-down menu and select the CFS drive created in step e in step 12 in "Installing Oracle Clusterware Version 10.2.0.1." d Click OK. 12 Click Next. 13 In the Recovery Configuration window, perform the following steps: a Select Specify Flash Recovery Area. b Click Browse.
23 In the Database Configuration Assistant window, click Yes. When completed, the Database Configuration Assistant window provides database configuration information. 24 Record the information in the Database Configuration Assistant window for future database administration. 25 Click Exit. The Start Cluster Database window appears and the cluster database starts. Installing Oracle RAC 10g R2 Using ASM This section provides information about installing the Oracle RAC 10g R2 software.
6 In the Specify Cluster Configuration window, perform the following steps: a Verify the public, private, and virtual Host names for the primary node. b If you want to change these values, click Edit and enter the desired values, and click OK. c Click Add. d Enter the public, private, and virtual Host names for the second node, and click OK. 7 Click Next. The Specify Network Interface Usage window appears, displaying a list of cluster-wide network interfaces.
Changing the css misscount Value 1 Shutdown all nodes except node 1. 2 On node 1, open a command prompt window. 3 At the command prompt, type the following and then press : cd %ORA_CLUSTERWARE_HOME%\bin\ where %ORA_CLUSTERWARE_HOME% is the home directory that you created in step 4 in "Installing Oracle Clusterware Version 10.2.0.1." 4 At the command prompt, type the following and press : crsctl set css misscount 120 5 Restart node 1 and login as administrator. 6 Start all other nodes.
6 Click Next. 7 In the Specify Hardware Cluster Installation Mode window, click Select All and click Next. 8 In the Product-Specific Prerequisite Checks window, click Next. 9 In the Select Configuration Option window, select Install database Software only, and click Next. 10 In the Summary window, click Install. 11 In the End of Installation window, perform the steps as listed. NOTE: You should perform the steps as listed in the window before proceeding with the next step. 12 Click Exit.
Installing Patchset 10.2.0.2 for Oracle 10g Database NOTE: Complete the following steps before creating a listener and a seed database. Ensure that all the Oracle services are running. NOTE: You must install the patchset software from the node where the Oracle RAC 10g R2 software was installed. If this is not the node where you are running the OUI, exit and install the patchset from that node. Patchset Installation Steps 1 Start the OUI located in the patchset folder. 2 In the Welcome window, click Next.
Configuring the Listener This section contains procedures to configure the listener, which is required to establish a remote client connection to a database. Perform the following steps on node 1: 1 Click Start, select Run and type netca. 2 Click OK. 3 In the Real Application Clusters Configuration window, select Cluster configuration and click Next. 4 In the Real Application Clusters Active Nodes window, select Select All nodes and click Next.
3 In the Run field, type the following and click OK: dbca The Database Configuration Assistant starts. 4 In the Welcome window, select Oracle Real Application Clusters database and click Next. 5 In the Operations window, click Create a Database and click Next. 6 In the Node Selection window, click Select All and click Next. 7 In the Database Templates window, click Custom Database and click Next.
g In the Stamp disks window, click Next. h Click Finish to save your settings. i Select the check boxes next to the available disks and click OK. 16 In the ASM Disk Groups window, click Create New. 17 In the Create Disk Group window, enter the information for the Flash Recovery Area. a In the Disk Group Name field, enter a name for the new disk group. For example, FLASH. b In the Redundancy box, select External. c Click Stamp Disks. d Select Add or change label and click Next.
21 In the Database Content window, click Next. 22 In the Database Services window, click Next. 23 In the Initialization Parameters window, click Next. 24 In the Database Storage window, click Next. 25 In the Creation Options window, click Finish. 26 In the Summary window, click OK. The Database Configuration Assistant window appears, and the Oracle software creates the database. NOTE: This procedure may take several minutes to complete.
Table 1-8. Supported Software Versions (continued) Software Component Supported Versions Broadcom BCM95701, BCM95703, BCM95703s, and Gigabit 5700 (base driver) 8.48.0.0 Broadcom BCM5708C Nextreme II GigE 2.6.14.0 Broadcom Advanced Control Suite (for NIC teaming) 8.3.
Uninstalling Oracle Clusterware You may be required to uninstall Oracle Clusterware to troubleshoot the following issues: • The Oracle Clusterware installation procedure failed. • The Configuration Assistant failed to install successfully. To uninstall Oracle Clusterware, run OUI on the cluster node, delete any remaining Oracle services, and clean the storage devices. Running OUI 1 On node 1, open an Explorer window and navigate to the following directory: %SystemDrive%\oracle\product\10.2.
3 Restart node 1 and log in as administrator. 4 Restart each of the other nodes and log in as administrator. Cleaning the Storage Devices 1 Clean the partitions that will be configured for the OCR registry (OCRCFG) and the voting disks. a Click Start and select Run. b In the Run field, type cmd and click OK. c At the command prompt, type the following and press : %SystemDrive%\oracle\product\10.2.0\crs\bin\ExportSYMLink where %SystemDrive% is the user’s local drive.
5 Launch the Oracle GUI Object Manager. At the command prompt, type the following and press : %SystemDrive%\ora_bin_utils\GUIOracleOBJManager.exe where %SystemDrive% is the user’s local drive. The Oracle Object Manager window appears. 6 Delete the symlinks for the OCR (OCRCFG) and voting disks (VOTEDSK). a Select ocrcfg and votesdk. b Click Options and select Commit. If successful, the OCRCFG and VOTEDSK entries disappear. c Click Options and select Exit to close the Oracle Object Manager.
Additional Troubleshooting Issues Table 1-9 provides recommended actions for problems that you may encounter while deploying and using your Windows Server 2003 operating system and Oracle Database 10g R2 software. Table 1-9. Troubleshooting Category Problem / Symptom Cause Recommended Corrective Action NIC Teaming Broadcom NIC teaming fails The following steps may result in a NIC teaming failure: • One of the Broadcom NICs that was used in the NIC teaming fails or is disabled.
Table 1-9. Category Troubleshooting (continued) Problem / Symptom Cause Recommended Corrective Action Oracle The cluster node The cluster node cannot Perform the following steps: Clusterware restarts with a communicate with the storage disks. 1 Restart the cluster node. blue screen. 2 During POST, press . 3 In the Windows Advanced Options Menu screen, select Safe Mode. 4 Select the appropriate operating system. 5 Logon to the system. 6 In the Desktop screen, click OK.
Table 1-9. Category Troubleshooting (continued) Problem / Symptom Cause System The cluster nodes The cluster nodes cannot access the blue screen generate a blue voting disk. screen. Recommended Corrective Action 1 Ensure that the HBA connection mode firmware settings are configured properly for your storage configuration. If your cluster nodes and storage system are configured in a direct-attached configuration, configure the Connection mode as: 0 - loop only.
Table 1-9. Troubleshooting (continued) Category Problem / Symptom Cause Recommended Corrective Action Storage Disks appear as unreachable. On the Windows desktop, when you right-click My Computer, select Computer Management, and then click Disk Management, the disks appear unreachable. Ensure that the storage LUNs are assigned to both cluster nodes. Causes: • The LUNs are not assigned to the cluster nodes. • Improper cabling. • The HBA drivers are not installed on the cluster node(s).
Table 1-9. Troubleshooting (continued) Category Problem / Symptom Cause Recommended Corrective Action VIPCA The VIPCA configuration fails. The public network adapter interface (or the network interface assigned for VIP in case 4 network interfaces) name is not identical on both cluster nodes. Ensure that the public network adapter interface name is identical on both cluster nodes.
Obtaining and Using Open Source Files The software contained on the Deployment CD is an aggregate of third-party programs as well as Dell programs. Use of the software is subject to designated license terms. All software that is designated as under the terms of the GNU GPL may be copied, distributed, and/or modified in accordance with the terms and conditions of the GNU General Public License, Version 2, June 1991.
Index A E L additional information, 40 examples Fibre Channel cluster hardware connections, 9 license agreements, 7 B bonding, 14 O F Fibre Channel cluster setup, 9 C cluster Fibre Channel hardware connections, example, 9 cluster setup Fibre Channel, 9 configuring Oracle 10g, 9 verifying hardware and software configurations, 9 configuring the private and public networks, 13 configuring the private network, 14 G getting help, 49 P private network configuring, 13-14 H hardware Fibre Channel cluster
Index T troubleshooting, 41 V verifying hardware configuration, 9 software configuration, 9 52 Index
Dell™ PowerEdge™ 系统 Oracle Database 10g R2 企业版 Real Application Cluster 适用于 Microsoft® Windows Server® 2003 x64 R2 标准版 和企业版部署指南 1.1 版 w w w. d e l l . c o m | s u p p o r t . d e l l .
注和注意 注:注表示可以帮助您更好地使用计算机的重要信息。 注意:注意表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 ___________________ 本说明文件中的信息如有更改,恕不另行通知。 © 2006 Dell Inc. 版权所有,翻印必究。 未经 Dell Inc. 书面许可,严禁以任何形式进行复制。 本文中使用的商标:Dell、DELL 徽标和 PowerEdge 是 Dell Inc. 的商标; Intel 和 Xeon 是 Intel Corporation 的注册商标; EMC、 Navisphere 和 PowerPath 是 EMC Corporation 的注册商标; Microsoft、Windows 和 Windows Server 是 Microsoft Corporation 的注册 商标。 本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。Dell Inc.
目录 软件和硬件要求 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 许可协议 . . . 重要说明文件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 安装和配置操作系统 . . . . . . . . . . . . . . . . . . . . . . . . . . . 使用 Deployment CD 安装操作系统 . 验证群集硬件与软件配置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 设置光纤信道群集 . . . . . . . . . . . 适用于 SAN 连接配置的存储系统布线 . 为 Oracle RAC 10g R2 配置网络和存储 . . . . . . . . . . . . . . . . . . .
在系统引导期间安装用于解决裂脑问题 (Split Brain Issue) 的 增补软件 . . . . . . . . . . . . . . . . . . . . . . . . . . . 配置监听程序 . . . . . . . . . . . . . . . . . . . . . . . . 创建基础 (Seed) 数据库 . . . . . . . . . . . . . . . . . . . 附加信息 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 解决群集件安装故障 卸载 Oracle 群集件 . . 其它故障排除问题 . . 获得帮助 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
本说明文件提供按照 Dell 支持的 Oracle 配置来安装、配置、重新安装以及使用 Oracle Database 10g R2 软件的相关信息。 请将本说明文件与 Dell Deployment CD 配合使用来安装软件。如果您仅使用操作系统 CD 来安装操作 系统,则本说明文件中的步骤可能不适用。 包括以下内容: • 软件和硬件要求。 • 安装和配置 Microsoft® Windows Server® 2003 x64 R2 企业版 / 标准版。 • 验证群集硬件与软件配置。 • 为 Oracle Database Real Application Clusters (RAC) 10g R2 配置网络和存储。 • 安装 Oracle Database RAC 10g R2 10.2.0.2 增补软件集和软件更新。 • 附加信息。 • 故障排除。 • 获得帮助。 有关 Dell 支持的 Oracle 配置的详情,请访问 Dell 和 Oracle 网站 dell.
软件和硬件要求 表 1-1 列出了 Dell 支持的 Oracle 配置的基本软件要求。表 1-2 列出了硬件要求。 有关驱动程序和应用程序最低软件版本的详情,请参阅“支持的软件版本”。 表 1-1. 软件要求 软件组件 配置 Microsoft Windows Server 2003 x64 R2 标准版 / 企业版 Oracle10g R2 10.2.0.1 版 企业版,包括用于群集的 RAC 选件 EMC® PowerPath®(仅限光纤信道 群集) 4.5 版 注:视用户数量、使用的应用程序、批处理进程以及其它因素而定,您可能需要一个超出最低硬件要求 的系统才能获得您所需的性能。 注:所有群集节点的硬件配置应完全相同。 表 1-2.
许可协议 注:您的 Dell 配置包含 30 天的 Oracle 软件试用许可。如果您没有此产品的许可证,请与 Dell 销售代表联系。 重要说明文件 有关特定硬件组件的详情,请参阅随系统附带的说明文件。 安装和配置操作系统 注意:为确保正确地安装操作系统,在安装操作系统之前,应断开系统与所有外部存储设备的连接。 本节介绍有关安装和配置 Windows Server 2003 x64 R2 企业版 / 标准版或 x64 标准版操作系统以实现 Oracle 部署的信息。 安装过程视随系统购买的安装 CD 不同而有所差异。有关适用于您的配置的安装过程,请参阅表 1-3。 表 1-3. 确定安装过程 所购 CD 安装过程 Windows Server 2003 x64 R2 标准版 / 企业版 请参阅“使用 Deployment CD 安装操作系统” Dell Deployment CD、Oracle 10g R2 安装 CD、 有关从 dell.
9 出现提示时,将 Microsoft Windows Server 2003 x64 R2 CD1 插入 CD 驱动器。 Windows 介质将复制到部署分区,系统将重新引导,然后继续安装。 10 在 Personalize Your Software(自定义软件)窗口的 Name(名称)和 Organization(组织)字段 中,输入相应的信息,然后单击 Next(下一步)。 11 出现提示时,输入 Windows Server 2003 x64 R2 标准版 / 企业版(含 SP1)的产品密钥,然后单击 Next(下一步)。 12 在 Computer Name(计算机名称)和 Administrator password(管理员密码)字段中,输入相应 的信息,然后单击 Next(下一步)。 注:要正确配置网络,计算机名称和公共主机名必须完全相同。 注:记下在此步骤中创建的登录密码。在步骤 17 中,您需要使用此信息。 13 按照窗口中的说明完成安装。 注:完成此过程可能需要几分钟。 完成安装过程后,屏幕将显示 Welcome to Windows(欢迎使用 Windows)窗口。 14 将所有外部存
验证群集硬件与软件配置 在开始群集设置之前,请确保硬件安装、公共接口和专用接口及节点软件的配置正确无误。以下各节 提供了有关光纤信道群集设置的信息。 设置光纤信道群集 在 Dell 专业服务代表完成了光纤信道群集的安装后,请根据本节所述的内容,验证硬件连接及硬件和 软件配置。 图 1-1, 图 1-2 和表 1-4 说明具有两个节点的存储区域网络 (SAN) 连接的光纤信道群集所需的群集连接。 图 1-1.
表 1-4.
表 1-5. LUN 配置和容量 LUN 最小容量 分区数 用途 1 1 GB 2 个(120 MB 和 50 MB) 投票磁盘,Oracle 群集件注 册表 (OCR) 2 大于数据库 1 数据库 3 至少为第二个 LUN 容量 的两倍 1 快闪恢复区域 适用于 SAN 连接配置的存储系统布线 图 1-2.
请使用以下过程,在具有四个端口的 SP SAN 连接配置中配置 Oracle 群集存储系统。 1 从 SP-A 端口 0 至光纤信道交换机 0 连接一条光缆。 2 从 SP-A 端口 1 至光纤信道交换机 1 连接一条光缆。 3 从 SP-B 端口 0 至光纤信道交换机 1 连接一条光缆。 4 从 SP-B 端口 1 至光纤信道交换机 0 连接一条光缆。 5 从节点 1 上的 HBA0 至光纤信道交换机 0 连接一条光缆。 6 从节点 1 上的 HBA1 至光纤信道交换机 1 连接一条光缆。 7 从每个附加节点的 HBA0 至光纤信道交换机 0 连接一条光缆。 8 从每个附加节点的 HBA1 至光纤信道交换机 1 连接一条光缆。 为 Oracle RAC 10g R2 配置网络和存储 本节介绍设置光纤信道群集的信息,其中包括以下过程: • 配置公共和专用网络。 • 验证存储配置。 • 为 Oracle 群集件和 Oracle 数据库配置共享存储。 注:Oracle RAC 10g R2 是一项复杂的数据库配置,要求按顺序执行以下一系列过程。要想用最少的时间 配置网络和存储,请按顺序执行以下过程。
配置专用网络并组队 在部署群集之前,为每个群集节点分配一个专用 IP 地址和主机名。这一过程确保了节点之间可以通过 专用接口相互通信。 表 1-7 提供了两个节点群集的网络配置的示例。 注:本示例假设所有 IP 地址都已在所有群集节点的 hosts(主机)文件中注册。 表 1-7. 网络配置示例 主机名 类型 IP 地址 注册位置 rac1 公共 155.16.170.1 %SystemRoot%\system32\drivers\etc\hosts rac2 公共 155.16.170.2 %SystemRoot%\system32\drivers\etc\hosts rac1-vip 虚拟 155.16.170.201 %SystemRoot%\system32\drivers\etc\hosts rac2-vip 虚拟 155.16.170.202 %SystemRoot%\system32\drivers\etc\hosts rac1-priv 专用 10.10.10.
l 在 Intel NIC's Properties(Intel NIC 的属性)窗口中,单击 OK(确定)。 m 关闭 Computer Management(计算机管理)窗口。 4 如果节点 1 配置了 Broadcom NIC,请按以下步骤配置 NIC 组队。否则,请转至步骤 5。 a 单击 Start(开始) → Programs(程序)→ Broadcom→ Broadcom Advanced Control Suite 2 (Broadcom 高级控制套件 2) 屏幕将显示 Broadcom Advanced Control Suite 2(Broadcom 高级控制套件 2) 窗口。 b 单击 Tools(工具),然后选择 Create a Team(创建组队)。 系统将显示 Broadcom Teaming Wizard(Broadcom 组队向导)窗口。 c 单击 Next(下一步)。 d 在 Enter the name for the team(输入组队的名称)字段中,键入 Private(专用), 然后单击 Next(下一步)。 e 在 Team Type(组
为公共网络适配器和专用网络适配器配置 IP 地址 注:对于支持 TIE 功能的 NIC,本解决方案不支持它的 TOE 功能。 1 更新适配器的网络接口名称(如果需要)。否则,请转至步骤 3。 a 在节点 1 上,单击 Start(开始),然后浏览至 Settings(设置)→ Control Panel(控制面 板)→ Network Connections(网络连接)。 b 在 Network Connections(网络连接)窗口中,右键单击要重命名的公共网络适配器,然后选 择 Rename(重命名)。 注:在群集节点上配置网络适配器时,请在所有群集节点上为公共适配器和专用适配器使用完 全相同的名称。否则,Oracle 数据库安装程序将生成错误,而无法完成安装过程。 c 将公共适配器名称重命名为 Public(公共),然后按 键。 d 右键单击要重命名的专用 NIC 组队,然后选择 Rename(重命名)。 e 将专用 NIC 组队重命名为 Private(专用),然后按 键。 f 在其它节点上重复步骤 a 至步骤 e。 2 配置 IP 地址。 注
d 确保网络适配器以下列所列顺序显示: 公共 专用 < 任何其它网络适配器 > 注:单击上下箭头键以更改适配器顺序。 e 单击 OK(确定)。 f 关闭 Network Connections(网络连接)窗口。 4 在两个节点上,将公共、专用及虚拟 IP 地址和主机名添加到 %SystemRoot%\system32\drivers\etc\hosts 文件中。 注:仅当公共和虚拟 IP 地址未向 DNS 服务器注册时,才将它们添加到 hosts(主机)文件中。 例如,以下各项使用表 1-7 中所示的适配器 IP 和主机名: 155.16.170.1 rac1 155.16.170.2 rac2 10.10.10.1 rac1-priv 10.10.10.2 rac2-priv 155.16.170.201 rac1-vip 155.16.170.
安装 Dell|EMC 所需的基于主机的软件 按照 Dell|EMC 说明文件中的过程安装 Dell|EMC 系统附带的 EMC Navisphere® 代理软件。 验证节点的存储分配 1 在 Windows 桌面上,右键单击 My Computer(我的电脑),然后选择 Manage(管理)。 2 在 Computer Management(计算机管理)窗口中,单击 Device Manager(设备管理器)。 3 展开 Disk drives(磁盘驱动器)。 4 在 Disk drives(磁盘驱动器)下,确保对于在存储设备中分配的各个 LUN 都显示四个小型计算机 系统接口 (SCSI) 磁盘设备。 5 展开 Storage(存储),然后单击 Disk Management(磁盘管理)。 如果屏幕上显示 Welcome to the Initialize and Convert Disk Wizard(欢迎使用初始化和转换磁盘 向导),请执行步骤 a 至步骤 d。否则,请转至步骤 6。 a 在 Welcome to the Initialize and Convert Disk Wizard(欢迎使
4 在窗口的左窗格中,展开 Storage Arrays(存储阵列)。 5 单击存储系统标识符。 在窗口的右窗格中,显示存储系统存储处理器。 6 在左窗格中,单击第一个 SP。 7 在 SP Configuration(SP 配置)窗口中,确保所有路径配置如下: • 在 State(状态)列中,状态为 Alive(活动)。 • 在 Mode(模式)列中,模式为 Active(激活)。 8 对另一个 SP 重复步骤 6 和步骤 7。 9 关闭 PowerPathAdmin 控制台。 将会显示一个信息窗口,提示您保存控制台设置。 10 单击 No(否)。 11 在 Windows 桌面上,右键单击 My Computer(我的电脑),然后选择 Manage(管理)。 12 展开 Storage(存储),然后单击 Disk Management(磁盘管理)。 对于存储中分配的每个 LUN,都将显示一个磁盘。 13 确保每个 LUN 都被配置为 Basic(基本)磁盘。 14 在其它节点上重复步骤 1 至步骤 13。 为 Oracle 群集件准备磁盘 本节介绍有关为以下磁盘创建逻辑驱动器的信息: • OC
4 单击 Next(下一步)。 5 在 Select Partition Type(选择分区类型)窗口中,选择 Extended partition(扩展分区),然后单 击 Next(下一步)。 6 在 Specify Partition Size(指定分区大小)窗口中,接受默认分区大小,然后单击 Next (下一步)。 7 单击 Finish(完成)。 在步骤 3 中选择的磁盘分区区域将配置为扩展分区。 8 在所有分配给群集节点的共享磁盘上,重复步骤 3 至步骤 7。 9 为 OCR 磁盘创建逻辑驱动器。 a 在确定用于 OCR 和投票磁盘 (1 GB LUN) 的磁盘分区区域中,右键单击可用空间,然后选择 New Logical Drive(新建逻辑驱动器)。 屏幕将显示 Welcome to the New Partition Wizard(欢迎使用新建分区向导)。 b 单击 Next(下一步)。 c 在 Select Partition Type(选择分区类型)窗口中,选择 Logical drive(逻辑驱动器),然后 单击 Next(下一步)。 d 在 Specify Partiti
使用 OCFS 为数据库存储准备数据库磁盘和快闪恢复区域 本节介绍如何创建逻辑驱动器,以便用来创建 Oracle 的群集文件系统 (OCFS) 存储磁盘。 注:如果您创建逻辑驱动器是为了创建自动存储管理 (ASM) 存储磁盘,则忽略以下步骤并参阅“使用 ASM 为数据库存储准备数据库磁盘和快闪恢复区域”。 1 在节点 1 上,为数据库创建一个逻辑驱动器。 a 找到分配用于 Oracle 数据库的磁盘。 b 在磁盘分区区域中,右键单击可用空间,然后选择 New Logical Drive(新建逻辑驱动器)。 屏幕将显示 Welcome to the New Partition Wizard(欢迎使用新建分区向导)。 c 单击 Next(下一步)。 d 在 Select Partition Type(选择分区类型)窗口中,选择 Logical drive(逻辑驱动器),然后 单击 Next(下一步)。 e 在 Specify Partition Size(指定分区大小)窗口的 Partition size in MB(以 MB 为单位的分区 大小)字段中,键入适当的大小,然后单击 Next(下
使用 ASM 为数据库存储准备数据库磁盘和快闪恢复区域 本节介绍如何创建逻辑驱动器,以便用来创建 ASM 磁盘存储。ASM 磁盘存储由一个或多个可以跨多 个磁盘的磁盘组组成。 注:如果您创建逻辑驱动器是为了创建 OCFS 存储磁盘,则忽略以下步骤并按照“使用 OCFS 为数据库存 储准备数据库磁盘和快闪恢复区域” 中的步骤执行。 1 为数据库创建一个逻辑驱动器。 a 找到分配用于 Oracle 数据库的磁盘。 b 在磁盘分区区域中,右键单击可用空间,然后选择 New Logical Drive(新建逻辑驱动器)。 屏幕将显示 Welcome to the New Partition Wizard(欢迎使用新建分区向导)。 c 单击 Next(下一步)。 d 在 Select Partition Type(选择分区类型)窗口中,选择 Logical drive(逻辑驱动器),然后 单击 Next(下一步)。 e 在 Specify Partition Size(指定分区大小)窗口的 Partition size in MB(以 MB 为单位的分区 大小)字段中,键入适当的大小,然后单击 Ne
为共享磁盘启用 Automount(自动安装)选项 1 在节点 1 上,单击 Start(开始),然后选择 Run(运行)。 2 在 Run(运行)字段中,键入 cmd,然后单击 OK(确定)。 3 在命令提示符下,键入 diskpart,然后按 键。 4 在 DISKPART 命令提示符下,键入 automount enable(启用自动安装),然后按 键。 屏幕将显示以下信息: Automatic mounting of new volumes enabled.(已启用新卷自动安装。) 5 在 DISKPART 命令提示符下,键入 exit,然后按 键。 6 关闭命令提示符。 7 在其它每个节点上重复执行步骤 1 至步骤 6。 8 重新启动节点 1,然后按顺序重新启动其它节点。 使用 OCFS 安装 Oracle RAC 10g R2 本节介绍有关安装 Oracle RAC 10g R2 软件的信息。包括以下主题: • 安装 Oracle 群集件 10.2.0.
3 单击 Next(下一步)。 4 在 Specify Home Details(指定主目录详细信息)窗口中,接受默认设置,然后单击 Next (下一步)。 注:记下 OraCR10g_home(CRS 主目录)路径,稍后您将需要这些信息。 5 在 Product Specification Prerequisite Checks(产品特定先决条件检查)窗口中,确保成功完成所 有检查,然后单击 Next(下一步)。 6 在 Specify Cluster Configuration(指定群集配置)窗口中,输入以下信息: • 另一个群集名称(如果需要)。 • 用于两个群集节点的公共和专用主机名。单击 Add(添加)以指定附加节点。 • 在 Add a new node to the existing cluster(在现有群集中添加新节点)窗口中,输入公共、 专用和虚拟主机名,然后单击 OK(确定)。 注:确保网络主机名不包括域名扩展。 7 单击 Next(下一步)。 屏幕将显示 Specify Network Interface Usage(指定网络接口使用)窗口,并显示群集范围的网络接 口列表。
c 在 Specify Disk Configuration(指定磁盘配置)窗口中,选择 Format partition with CFS (使用 CFS 格式化分区)。 d 确保选中 Use partition for data storage(将分区用于数据存储)。 e 使用 Assign Drive Letter(分配驱动器号)选项的下拉式菜单,为分区分配驱动器号。 f 单击 OK(确定)。 13 在 Cluster Configuration Storage(群集配置存储)窗口中,为快闪恢复执行以下步骤: a 找到在“使用 OCFS 为数据库存储准备数据库磁盘和快闪恢复区域”的步骤 2 中创建的分区。 b 选择此分区,然后单击 Edit(编辑)。 c 在 Specify Disk Configuration(指定磁盘配置) 窗口中,选择 Format partition with CFS (使用 CFS 格式化分区)。 d 确保选中 Use partition for data storage(将分区用于数据存储)。 e 使用 Assign Drive Letter
4 在命令提示符下,键入下列命令并按 键: crsctl set css misscount 120 5 重新启动节点 1,并以管理员身份登录。 6 启动所有其它节点。 安装 Oracle Database 10g R2 以及 Real Application Clusters 10.2.1 1 在节点 1 上,将 Oracle Database 10g Release 2 for Microsoft Windows CD 插入 CD 驱动器。 屏幕将显示 Oracle Database 10g - Autorun(Oracle Database 10g - 自动运行)窗口。如果屏幕未 显示 Oracle Database 10g - Autorun(Oracle Database 10g - 自动运行)窗口: a 单击 Start(开始),然后选择 Run(运行)。 b 在 Run(运行)字段中,键入以下命令,然后单击 OK(确定): %CD-ROM 驱动器 %:\autorun\autorun.
9 在 Select Configuration Option(选择配置选项)窗口中,选择 Install database Software only (仅安装数据库软件),然后单击 Next(下一步)。 10 在 Summary(摘要)窗口中,单击 Install(安装)。 11 在 End of Installation(安装完成)窗口中,执行窗口中列出的过程。 注:必须先执行窗口中列出的过程,然后才能执行后续过程。 12 完成了在 End of Installation(安装完成)窗口中列出的所需过程后,单击 Exit(退出)。 13 在 Exit(退出)窗口中,单击 Yes(是)。 安装增补软件集 10.2.0.2 注:以下增补软件集安装步骤仅安装 Oracle 软件,如 10.2.0.1 群集件和尚未在系统上创建的 10.2.0.1 数据 库二进制文件(含基础 (seed) 数据库)。 1 可以从 metalink.oracle.com 下载增补软件集 10.2.0.
6 在 End of Installation(安装完成)窗口中,执行 Summary(摘要)中列出的除步骤 1 之外的所 有步骤。 7 在 End of Installation(安装结束)窗口中,单击 Exit(退出),然后单击 Yes(是)以退出 OUI。 安装适用于 Oracle 10g 数据库的增补软件集 10.2.0.2 注:在创建监听程序和基础 (seed) 数据库之前,请完成以下步骤。确保运行所有 Oracle 服务。 注:必须从安装了 Oracle RAC 10g R2 软件的节点上安装增补软件集软件。如果该节点不是运行 OUI 的节 点,请退出并在运行 OUI 的节点上安装增补软件集。 增补软件集安装步骤 1 启动增补软件集文件夹中的 OUI。 例如:%SystemDrive%\Oracle_patch\setup.
在系统引导期间安装用于解决裂脑问题 (Split Brain Issue) 的增补软件 1 浏览至标有 patch5059258 的文件夹。 2 将 opmd.exe 文件复制到所有节点上的 %CRS_HOME%\bin 目录。 3 在命令提示符下键入以下命令, %SystemDrive%\%CRS_HOME%\bin> ompd.
创建基础数据库 本节包含利用 OCFS 创建基础 (seed) 数据库和验证基础数据库的过程。 执行以下步骤,使用 OCFS 创建基础 (seed) 数据库: 1 在节点 1 上,单击 Start(开始),然后选择 Run(运行)。 2 在 Run(运行)字段中,键入 dbca,然后单击 OK(确定)。 启动 Database Configuration Assistant(数据库配置助手)。 3 在 Welcome(欢迎)窗口中,选择 Oracle Real Application Clusters database(Oracle Real Application Clusters 数据库),然后单击 Next(下一步)。 4 在 Operations(操作)窗口中,单击 Create a Database(创建数据库),然后单击 Next (下一步)。 5 在 Node Selection(节点选择)窗口中,单击 Select All(全选),然后单击 Next(下一步)。 6 在 Database Templates(数据库模板)窗口中,单击 Custom Database(自定义数据库),然后 单击
13 在 Recovery Configuration(恢复配置)窗口中,执行以下步骤: a 选择 Specify Flash Recovery Area(指定快闪恢复区域)。 b 单击 Browse(浏览)。 c 在 Directory Browse(目录浏览)窗口中,使用下拉式菜单选择在“安装 Oracle 群集件 10.2.0.
使用 ASM 安装 Oracle RAC 10g R2 本节介绍有关安装 Oracle RAC 10g R2 软件的信息。包括以下主题: • 安装 Oracle 群集件 10.2.0.1 版 • 更改 css misscount 值 • 安装 Oracle10g 数据库以及 Real Application Clusters 10.2.0.1 • 安装增补软件集 10.2.0.1 • 配置监听程序 • 创建基础数据库 安装 Oracle 群集件 10.2.0.1 版 1 在节点 1 上,将 Oracle Clusterware CD 插入 CD 驱动器。 OUI 将启动,并显示 Welcome(欢迎)屏幕。 如未显示 Welcome(欢迎)屏幕: a 单击 Start(开始),然后选择 Run(运行)。 b 在 Run(运行)字段中,键入下列命令,然后单击 OK(确定): %CD 驱动器 %\autorun\autorun.
8 在 Interface Type(接口类型)下拉式菜单中,通过选择 Interface Name(接口名称)并单击 Edit (编辑),将公共 Interface Type(接口类型)配置为 Public(公共),然后将专用 Interface Type (接口类型)配置为 Private(专用)(如果需要)。选择正确的 Interface Type(接口类型), 然后单击 OK(确定)。 9 单击 Next(下一步)。 10 在 Cluster Configuration Storage(群集配置存储)屏幕中,为 OCR 磁盘执行以下步骤: a 找到在小节“为群集件准备 OCR 磁盘和投票磁盘”中创建的 120 MB 分区。 b 选择此分区,然后单击 Edit(编辑)。 c 在 Specify Disk Configuration(指定磁盘配置)窗口中,选择 Place OCR (Primary) on this partition(在此分区上放置 OCR [ 主分区 ]),然后单击 OK(确定)。 11 在 Cluster Configuration Storage(群集配置存储)屏幕中,
4 在命令提示符下,键入下列命令并按 键: crsctl set css misscount 120 5 重新启动节点 1,并以管理员身份登录。 6 启动所有其它节点。 安装 Oracle10g 数据库以及 Real Application Clusters 10.2.0.1 1 将 Oracle Database 10g Release 2 CD 插入 CD 驱动器。 OUI 将启动,并显示 Welcome(欢迎)屏幕。 如果未显示 Welcome(欢迎)屏幕: a 单击 Start(开始),然后选择 Run(运行)。 b 在 Run(运行)字段中,键入: %CD 驱动器 %\autorun\autorun.
10 在 Summary(摘要)窗口中,单击 Install(安装)。 11 在 End of Installation(安装完成)窗口中,执行窗口中列出的步骤。 注:必须先执行窗口中列出的步骤,然后才能执行后续过程。 12 单击 Exit(退出)。 安装增补软件集 10.2.0.2 注:以下增补软件集安装步骤仅安装 Oracle 软件,如 10.2.0.1 群集件和尚未在系统上创建的 10.2.0.1 数据 库二进制文件(含基础 (seed) 数据库)。 1 从 Oracle Metalink 网站 metalink.oracle.com 下载增补软件集 10.2.0.2。 2 将增补软件集解压到以下位置 %SystemDrive%。 其中,%SystemDrive% 为用户的本地驱动器。 安装适用于 Oracle 10g 群集件的增补软件集 10.2.0.
安装适用于 Oracle 10g 数据库的增补软件集 10.2.0.2 注:在创建监听程序和基础 (seed) 数据库之前,请完成以下步骤。确保运行所有 Oracle 服务。 注:必须从安装了 Oracle RAC 10g R2 软件的节点上安装增补软件集软件。如果该节点不是运行 OUI 的节 点,请退出并在运行 OUI 的节点上安装增补软件集。 增补软件集安装步骤 1 启动增补软件集文件夹中的 OUI。 2 在 Welcome(欢迎)窗口中单击 Next(下一步)。 3 在 Specify home details(指定主目录详细信息)窗口中,从下拉式列表中选择作为 OraDb10g_home1 的名称,以将增补软件集安装到 Oracle 主目录中,然后单击 Next(下一步)。 4 在 Specify Hardware Cluster Installation Mode(指定硬件群集安装模式)窗口中,然后单击 Next (下一步)。 5 在 Summary(摘要)窗口中,单击 Install(安装)。 在安装过程中,屏幕可能会显示以下错误信息:Error in writing to file oci.
配置监听程序 本节包含了配置监听程序的步骤,与数据库建立远程客户机连接时需要使用此程序。 在节点 1 上执行以下步骤: 1 单击 Start(开始),选择 Run(运行),然后键入 netca。 2 单击 OK(确定)。 3 在 Real Application Clusters Configuration(Real Application Clusters 配置)窗口中,选择 Cluster Configuration(群集配置),然后单击 Next(下一步)。 4 在 Real Application Clusters Active Nodes(Real Application Clusters 活动节点)窗口中,选择 Select all nodes(选择所有节点),然后单击 Next(下一步)。 5 在 Welcome(欢迎)窗口中,选择 Listener configuration(监听程序配置),然后单击 Next (下一步)。 6 在 Listener Configuration, Listener(监听程序配置,监听程序)窗口中,选择 Add(添加), 然后单击 Next(下一步)。 7 在
2 在节点 1 上,单击 Start(开始),然后选择 Run(运行)。 3 在 Run(运行)字段中,键入下列命令,然后单击 OK(确定): dbca 启动 Database Configuration Assistant(数据库配置助手)。 4 在 Welcome(欢迎)窗口中,选择 Oracle Real Application Clusters database(Oracle Real Application Cluster 数据库),然后单击 Next(下一步)。 5 在 Operations(操作)窗口中,单击 Create a Database(创建数据库),然后单击 Next (下一步)。 6 在 Node Selection(节点选择)窗口中,单击 Select All(全选),然后单击 Next(下一步)。 7 在 Database Templates(数据库模板)窗口中,单击 Custom Database(自定义数据库),然后 单击 Next(下一步)。 8 在 Database Identification(数据库标识)窗口的 Global Database Name(全局数据库名称
d 选择 Add or change label(添加或更改标签),然后单击 Next(下一步)。 e 在 Select disks(选择磁盘)屏幕中,按 键,然后选择在 Status(状态)列中分配了 Candidate device(候选设备)的前两个磁盘。 f 在 Generate stamps with this prefix(使用此前缀生成标记)字段中,保持默认设置,然后单 击 Next(下一步)。 g 在 Stamp disks(标记磁盘)窗口中,单击 Next(下一步)。 h 单击 Finish(完成)以保存您的设置。 i 选择可用磁盘旁边的复选框,然后单击 OK(确定)。 16 在 ASM Disk Groups(ASM 磁盘组)窗口中,单击 Create New(新建)。 17 在 Create Disk Group(创建磁盘组)窗口中,输入快闪恢复区域的信息。 a 在 Disk Group Name(磁盘组名称)字段中,输入新磁盘组的名称。 例如,FLASH。 b 在 Redundancy(冗余)框中,选择 External(外部)。 c 单
f 单击 Edit Archive Mode Parameters(编辑存档模式参数)。 • g 在 Edit Archive Mode Parameters(编辑存档模式参数)窗口中,确保在 Archive Log Destinations(存档日志目标)中列出的路径如下所示:+FLASH/,其中 FLASH 为您在 步骤 17 的步骤 a 中指定的快闪恢复区域磁盘组名称。 单击 Next(下一步)。 21 在 Database Content(数据库内容)窗口中,单击 Next(下一步)。 22 在 Database Services(数据库服务)窗口中,单击 Next(下一步)。 23 在 Initialization Parameters(初始化参数)窗口中,单击 Next(下一步)。 24 在 Database Storage(数据库存储)窗口中,单击 Next(下一步)。 25 在 Creation Options(创建选项)窗口中,单击 Finish(完成)。 26 在 Summary(摘要)窗口中,单击 OK(确定)。 屏幕将显示 Database Configuration Ass
表 1-8. 支持的软件版本(续) 软件组件 支持的版本 Intel PRO PCIe 千兆位适配器系列 9.4.24.1 Intel PROSet(用于 NIC 组队) 10.2.78.5 Broadcom BCM95701、BCM95703、BCM95703s 和 Gigabit 5700(基本驱动程序) 8.48.0.0 Broadcom BCM5708C Nextreme II GigE 2.6.14.0 Broadcom 高级控制套件 (对于 NIC 组队) 8.3.
卸载 Oracle 群集件 要排除下列问题,可能需要卸载 Oracle 群集件: • Oracle 群集件安装过程失败。 • 配置助手无法成功安装。 要卸载 Oracle 群集件,请在群集节点上运行 OUI,删除任何其它的 Oracle 服务,然后清除存储设备。 运行 OUI 1 在节点 1 上,打开资源管理器窗口,并浏览至以下目录: %SystemDrive%\oracle\product\10.2.0\crs\oui\bin 其中,%SystemDrive% 为用户的本地驱动器。 2 双击 setup.
清除存储设备 1 清除要配置用于 OCR 注册表 (OCRCFG) 磁盘和投票磁盘的分区。 a 单击 Start(开始),然后选择 Run(运行)。 b 在 Run(运行)字段中,键入 cmd,然后单击 OK(确定)。 c 在命令提示符下,键入下列命令并按 键: %SystemDrive%\oracle\product\10.2.0\crs\bin\ExportSYMLink 其中,%SystemDrive% 为用户的本地驱动器。 Oracle 符号链接导出程序 (ExportSYMLink) 将指向 SYMMAP.TBL 文件的符号链接导入当前 目录下。 d 在命令提示符下,键入下列命令并按 键: notepad SYMMAP.
5 启动 Oracle GUI 对象管理器。 在命令提示符下,键入下列命令并按 键: %SystemDrive%\ora_bin_utils\GUIOracleOBJManager.exe 其中,%SystemDrive% 为用户的本地驱动器。 屏幕将显示 Oracle Object Manager(Oracle 对象管理器)窗口。 6 删除用于 OCR 磁盘 (OCRCFG) 和投票磁盘 (VOTEDSK) 的符号链接。 a 选择 ocrcfg 和 votesdk。 b 单击 Options(选项),然后选择 Commit(提交)。 如果成功,OCRCFG 和 VOTEDSK 项将消失。 c 单击 Options(选项),然后单击 Exit(退出),以关闭 Oracle 对象管理器。 7 启动计算机管理控制台。 a 在 Windows 桌面上,单击 Start(开始),然后选择 Run(运行)。 b 在 Run(运行)字段中,键入下列命令,然后按 键: compmgmt.
其它故障排除问题 表 1-9 针对在部署或使用 Windows Server 2003 操作系统和 Oracle Database 10g R2 软件时可能遇到的问 题提供了建议的纠正措施。 表 1-9.
表 1-9.
表 1-9. 故障排除(续) 类别 问题 / 症状 原因 系统蓝屏 群集节点生成 蓝屏。 群集节点不能访问投票磁盘。 建议的纠正措施 1 确保对存储配置正确地配置了 HBA 连 接方式固件设置。 如果群集节点和存储系统采用直接连接 配置进行配置,则将 Connection(连 接)模式配置为:0 - loop only(0 - 仅 回路)。 如果群集节点和存储系统是通过光纤信 道交换机连接的,则将 Connection (连接)模式配置为 2 - loop preferred, otherwise point-to-point(2 - 首选回路, 否则为点到点)。 2 如果问题仍然存在,则将 CSS 计数误 差增加为高于 120 的值。 3 请执行以下步骤: a 关闭除节点 1 之外的其它所有节点。 b 在节点 1 上,打开命令提示窗口。 c 键入下列命令并按 键: %ORA_CLUSTERWARE_HOME%\ bin 其中, %ORA_CLUSTERWARE_HOME% 为 您在“安装 Oracle 群集件 10.2.0.
表 1-9.
获得帮助 Dell 支持 有关使用系统的详情,请参阅随系统组件附带的说明文件。有关白皮书、Dell 支持的配置和一般信息, 请访问 dell.com/10g。要获得硬件和操作系统软件的 Dell 技术支持并下载最新的系统更新,请访问 Dell 支持 Web 站点 support.dell.com。与 Dell 联系的有关信息包含在系统《安装与故障排除指南》中。 我们现在还提供 Dell 企业培训与认证服务,请访问 www.dell.com/training 了解详情。此培训服务可能 不在所有地区提供。 Oracle 支持 有关 Oracle 软件和应用程序群集件的培训信息及 Oracle 联系信息,请访问 Oracle 网站 oracle.com 或 参阅 Oracle 说明文件。 技术支持、下载和其它技术信息可以在 Oracle MetaLink 网站 metalink.oracle.
索引 A P X 安装 Oracle RAC 10g, 83 Red Hat Enterprise Linux, 59 配置 Oracle 10g , 61 验证硬件与软件配置 , 61 许可协议 , 59 配置专用和公共网络 , 64 配置专用网络 , 65 Q 验证 软件配置 , 61 硬件配置 , 61 群集 光纤信道硬件连接, 示例 , 61 硬件 光纤信道互连 , 62 光纤信道群集最低要求 , 58 群集设置 光纤信道 , 61 硬件和软件配置 光纤信道 , 62 R Z Red Hat Enterprise Linux 安装 , 59 支持的存储设备 , 91 B 绑定 , 65 F 附加信息 , 91 G 公共网络 配置 , 64 故障排除 , 92 光纤信道群集设置 , 61 H 获得帮助 , 100 O Oracle RAC 10g 安装 , 83 配置网络和存储 , 64 Y 软件 要求 , 58, 91 专用网络 配置 , 64-65 软件和硬件要求 , 58 S 示例 光纤信道群集硬件连接 , 61 说明文件 , 59 索引 1
À˜“″ 102 索引
Systèmes Dell™ PowerEdge™ Oracle Database 10g Release 2, Enterprise Edition Real Application Cluster pour Microsoft® Windows Server® 2003 R2, Standard Edition et Enterprise Edition 64 bits Guide de déploiement Version 1.1 w w w. d e l l . c o m | s u p p o r t . d e l l .
Remarques et avis REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : un AVIS vous avertit d'un dommage ou d'une perte de données potentiels et vous indique comment éviter ce problème. ___________________ Les informations contenues dans ce document peuvent être modifiées sans préavis. © 2006 Dell Inc. Tous droits réservés. La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.
Sommaire Configuration matérielle et logicielle requise . Contrats de licence . . . . Documentation importante . . . . . . . . . . . . . . 108 . . . . . . . . . . . . . . . . . . . . . 109 109 . . . . . . . . . . . . . . . . . . . . . Installation et configuration du système d'exploitation . . . . . . . . . . Installation du système d'exploitation à l'aide des CD de déploiement . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 . . . . 111 . . . . . . 111 . . . . . .
Installation du correctif 10.2.0.2 . . . . . . . . . . . . . . Installation des correctifs Oracle les plus récents. . . . . . Installation du correctif concernant le scénario "split brain" constaté à l'amorçage du système . . . . . . . . . . . . . Configuration de l'écouteur . . . . . . . . . . . . . . . . Création de la base de données initiale . . . . . . . . . . . Informations supplémentaires . . . . . . . . . . . . . . . . . . . . . . 147 147 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ce document contient des informations concernant l'installation, la configuration, la réinstallation et l'utilisation du logiciel Oracle Database 10g R2. Il fait partie du support fourni par Dell pour les configurations Oracle. Pour installer le logiciel, utilisez ce document ainsi que le CD Dell Deployment. Si vous utilisez uniquement les CD du système d'exploitation pour installer ce dernier, les instructions fournies dans ce document peuvent ne pas s'appliquer.
Configuration matérielle et logicielle requise Le tableau 1-1 présente la configuration de base requise au niveau logiciel pour la prise en charge des configurations Oracle par Dell. Le tableau 1-2 présente la configuration matérielle requise. Pour obtenir des informations détaillées sur les versions minimales des pilotes et des applications à installer, voir "Versions de logiciels prises en charge". Tableau 1-1.
Contrats de licence REMARQUE : la licence Oracle fournie avec la configuration Dell est valable 30 jours. Si vous ne possédez pas la licence de ce produit, contactez votre représentant commercial Dell. Documentation importante Pour plus d'informations sur certains composants matériels spécifiques, consultez la documentation fournie avec le système.
5 Insérez le disque Dell Deployment CD1 dans le lecteur. Le système démarre à partir du CD. Au démarrage, un écran de texte vous invite à sélectionner une option. Si le système n'a pas démarré à partir du CD, réinitialisez-le. Lors du redémarrage, appuyez sur F2 et vérifiez que le lecteur de CD apparaît en premier dans la séquence d'amorçage. 6 À l'invite de commande, tapez 3 pour sélectionner Oracle 10g R2 EE On Windows Server 2003 x64 R2 SE/EE et appuyez sur .
Mise à jour des chemins de répertoires temporaires Procédez comme suit pour vérifier que les chemins des répertoires Temp et Tmp ont été définis correctement. 1 Cliquez sur Démarrer et sélectionnez Exécuter. 2 Dans le champ Ouvrir, tapez cmd et cliquez sur OK. 3 À l'invite de commande, tapez echo %Temp% et appuyez sur . Le chemin suivant s'affiche : %LecteurSystème%\Temp où %LecteurSystème% correspond au lecteur local de l'utilisateur.
Figure 1-1. Connexions matérielles pour un cluster Fibre Channel connecté à un SAN Réseau public Commutateurs Ethernet Gigabit (réseau privé) LAN/WAN Systèmes PowerEdge (base de données Oracle) Commutateurs Fibre Channel (SAN) Dell | EMC CAT 5e/6 (NIC Gigabit cuivre) CAT 5e/6 (NIC Gigabit cuivre) Câbles à fibres optiques Systèmes de stockage Fibre Channel Dell | EMC CX300, CX500, CX700, CX3-20, CX3-40 ou CX3-80 Tableau 1-4.
Tableau 1-4. Interconnexions matérielles pour Fibre Channel (suite) Composant du cluster Connexions Chaque commutateur Fibre Channel Dell | EMC Une connexion optique entre chaque processeur SP et une carte adaptateur de bus hôte sur chaque nœud PowerEdge.
Tableau 1-5. Configuration et taille des unités logiques Unité logique (LUN) Taille minimale Nombre de partitions Utilisée pour 1 1 Go 2 (120 Mo et 50 Mo) Disque de vote, Registre OCR (Oracle Clusterware Registry) 2 Supérieure à la taille de la base de données 1 Base de données 3 Au moins deux fois la taille 1 de la deuxième unité logique Zone de récupération Flash Câblage d'un système de stockage dans une configuration avec connexion à un SAN Figure 1-2.
Pour configurer le système de stockage du cluster Oracle dans une configuration à 4 ports avec connexion à un SAN, procédez comme suit : 1 Installez un câble optique entre le port 0 du SP-A et le commutateur Fibre Channel 0. 2 Installez un câble optique entre le port 1 du SP-A et le commutateur Fibre Channel 1. 3 Installez un câble optique entre le port 0 du SP-B et le commutateur Fibre Channel 1. 4 Installez un câble optique entre le port 1 du SP-B et le commutateur Fibre Channel 0.
Selon le nombre de ports pour NIC disponibles, configurez les interfaces publique et privée comme décrit dans le tableau 1-6. Tableau 1-6.
c Affichez l'onglet Cartes réseau. d Faites un clic droit sur l'un des NIC Intel faisant partie de ceux qui doivent être regroupés, puis cliquez sur Propriétés. e Cliquez sur l'onglet Teaming (Regroupement). f Sélectionnez Team with other Adapters (Regrouper avec d'autres cartes), puis New Team (Nouveau regroupement). g Indiquez le nom du regroupement de NIC et cliquez sur Next (Suivant).
h Dans la fenêtre Designating Standby Member (Désignation d'un membre de réserve), sélectionnez Do not configure a Standby Member (Ne configurer aucun membre de réserve). Cliquez ensuite sur Next. i Dans la fenêtre Configuring LiveLink (Configuration de LiveLink), sélectionnez No et cliquez sur Next. j Dans la fenêtre Creating/Modifying a VLAN (Création/Modification d'un VLAN), sélectionnez No et cliquez sur Next.
2 Configurez les adresses IP. REMARQUE : vous devez définir une passerelle par défaut pour l'interface publique. Dans le cas contraire, l'installation de Clusterware risque d'échouer. a Cliquez sur Démarrer→ Paramètres→ Panneau de configuration→ Connexions réseau→ Public→ Propriétés. b Double-cliquez sur Protocole Internet (TCP/IP). c Cliquez sur Utiliser l'adresse IP suivante, entrez l'adresse IP requise, l'adresse de la passerelle par défaut et l'adresse IP du serveur DNS. Cliquez ensuite sur OK.
4 Sur chaque nœud, ajoutez le nom d'hôte, ainsi que et les adresses IP privée, publique et virtuelle, au fichier %RacineSystème%\system32\drivers\etc\hosts. REMARQUE : n'ajoutez les adresses IP publique et virtuelle au fichier hosts que si elles ne sont pas enregistrées sur le serveur DNS. Par exemple, les entrées suivantes utilisent l'adresse IP et le nom d'hôte de la carte figurant dans le tableau 1-7 : 155.16.170.1 rac1 155.16.170.2 rac2 10.10.10.1 rac1-priv 10.10.10.2 rac2-priv 155.16.170.
Vérification de l'affectation des unités de stockage aux noeuds 1 Sur le bureau Windows, faites un clic droit sur Poste de travail et sélectionnez Gérer. 2 Dans la fenêtre Gestion de l'ordinateur, cliquez sur Gestionnaire de périphériques. 3 Développez la section Lecteurs de disque. 4 Sous Lecteurs de disque, vérifiez que quatre disques SCSI apparaissent pour chaque unité logique affectée au stockage. 5 Cliquez sur Stockage et sélectionnez Gestion des disques.
5 Cliquez sur l'identificateur du système de stockage. Les processeurs de stockage (SP) du système de stockage apparaissent dans le volet droit de la fenêtre. 6 Dans le volet de gauche, cliquez sur le premier processeur SP. 7 Dans la fenêtre SP Configuration (Configuration du processeur SP), vérifiez que tous les chemins sont configurés comme suit : • La colonne State (État) doit contenir l'état Alive (Opérationnel). • La colonne Mode doit contenir le mode Active (Actif).
Préparation du disque OCR et du disque de vote pour Clusterware 1 Sur le bureau Windows, faites un clic droit sur Poste de travail et sélectionnez Gérer. 2 Développez l'élément Stockage et sélectionnez Gestion des disques. Le disque de stockage initialisé à la section "Vérification du fonctionnement de PowerPath" apparaît comme étant Non alloué. 3 Faites un clic droit sur la zone de partition des premiers disques partagés affectés aux nœuds du cluster, puis sélectionnez Nouvelle partition.
10 Créez un lecteur logique pour le disque de vote. a Dans la zone de partition, faites un clic droit sur l'espace disponible et sélectionnez Créer un nouveau lecteur logique. La fenêtre Bienvenue dans l'Assistant Création d'une nouvelle partition s'affiche. b Cliquez sur Suivant. c Dans la fenêtre Type de partition, sélectionnez Lecteur logique et cliquez sur Suivant. d Dans la fenêtre Spécifier la taille de la partition, tapez 50 dans le champ Taille de la partition en Mo et cliquez sur Suivant.
2 Sur le nœud 1, créez un lecteur logique pour la zone de récupération flash. a Repérez le disque affecté à la zone de récupération flash. b Effectuez la procédure décrite de l'étape b à l'étape h (étape 1). 3 Redémarrez tous les autres nœuds et connectez-vous en tant qu'administrateur. 4 Sur le bureau Windows de chacun des autres nœuds, faites un clic droit sur Poste de travail puis sélectionnez Gérer.
g Dans la fenêtre Formater une partition, sélectionnez Ne pas formater cette partition et cliquez sur Suivant. h Cliquez sur Terminer. 2 Créez un lecteur logique pour la zone de récupération flash. a Repérez le disque affecté à la zone de récupération flash. b Effectuez la procédure décrite de l'étape b à l'étape h (étape 1). 3 Redémarrez tous les autres nœuds et connectez-vous en tant qu'administrateur.
Installation d'Oracle RAC 10g R2 avec OCFS Cette section fournit des informations sur l'installation du logiciel Oracle RAC 10g R2. Les thèmes abordés sont les suivants : • Installation d'Oracle Clusterware version 10.2.0.1 • Modification de la valeur css misscount • Installation d'Oracle Database 10g R2 avec Real Application Clusters 10.2.1 • Installation du correctif 10.2.0.
6 Dans la fenêtre Specify Cluster Configuration (Définir la configuration du cluster), entrez les éléments suivants : • Un autre nom pour le cluster (facultatif) • Le nom d'hôte des réseaux public et privé pour les deux nœuds du cluster. Cliquez sur Add (Ajouter) pour définir des nœuds supplémentaires. • Dans la fenêtre Add a new node to the existing cluster (Ajouter un nœud à un cluster existant), entrez les noms public et privé du nouveau nœud ainsi que son nom d'hôte virtuel, puis cliquez sur OK.
12 Dans la fenêtre Cluster Configuration Storage (Stockage de la configuration du cluster), effectuez les procédures suivantes pour la base de données : a Identifiez la partition créée à l'étape 1 de la section "Préparation du disque de la base de données et de la zone de récupération flash pour le stockage de la base de données avec OCFS". b Sélectionnez-la et cliquez sur Edit (Modifier).
c Ne tenez pas compte du message d'avertissement et cliquez sur OK. d Cliquez sur Exit (Quitter) pour fermer la session OUI. e Dans la fenêtre de fermeture, cliquez sur Yes. Modification de la valeur css misscount 1 Arrêtez tous les nœuds, à l'exception du nœud 1. 2 Sur le nœud 1, ouvrez une fenêtre d'invite de commande.
5 Dans la fenêtre Specify Home Details (Indiquer l'emplacement racine), vérifiez les éléments suivants de la section Destination : • Le répertoire racine d'Oracle Database affiché dans le champ Name (Nom) est OraDb10g_home1. • Le champ Path (Chemin) contient le chemin complet du répertoire racine d'Oracle, à savoir : %LecteurSystème%\oracle\produit\10.2.0\db_1 où %LecteurSystème% correspond au lecteur local de l'utilisateur.
Installation du correctif 10.2.0.2 pour Oracle 10g Clusterware Avant de commencer 1 Arrêtez les applications sur tous les nœuds, à l'aide de la commande suivante : %LecteurSystème%:\%RACINE_CRS%\bin> srvctl stop nodeapps -n où %LecteurSystème% correspond au lecteur local de l'utilisateur. 2 Arrêtez les services Oracle sur tous les noeuds. Étapes de l'installation du correctif REMARQUE : vous devez installer le correctif à partir du nœud sur lequel Oracle RAC 10g R2 a été installé.
3 Dans la fenêtre Specify home details (Indiquer l'emplacement racine), sélectionnez OraDb10g_home1 dans la liste déroulante et cliquez sur Next. 4 Dans la fenêtre Specify Hardware Cluster Installation Mode (Définition du mode d'installation du cluster), cliquez sur Next. 5 Dans la fenêtre Summary (Récapitulatif), cliquez sur Install (Installer). Au cours de l'installation, il est possible que le message d'erreur suivant s'affiche : Error in writing to file oci.dll (Erreur d'écriture dans le fichier oci.
Configuration de l'écouteur Cette section indique comment configurer l'écouteur, qui est requis pour la connexion des clients distants à la base de données. Sur le nœud 1, procédez comme suit : 1 Cliquez sur Démarrer, sélectionnez Exécuter puis tapez : netca 2 Cliquez sur OK. 3 Dans la fenêtre Real Application Clusters, Configuration, sélectionnez Cluster Configuration (Configuration du cluster) et cliquez sur Next.
4 Dans la fenêtre Operations (Opérations), cliquez sur Create a Database (Créer une base de données), puis cliquez sur Next. 5 Dans la fenêtre Node Selection (Sélection des nœuds), cliquez sur Select All (Sélectionner tout), puis cliquez sur Next. 6 Dans la fenêtre Database Templates (Modèles de base de données), cliquez sur Custom Database (Base de données personnalisée), puis cliquez sur Next.
14 Cliquez sur Enable Archiving (Activer l'archivage). 15 Cliquez sur Edit Archive Mode Parameters (Modifier les paramètres du mode d'archivage).
Installation d'Oracle RAC 10g R2 avec ASM Cette section fournit des informations sur l'installation du logiciel Oracle RAC 10g R2. Les thèmes abordés sont les suivants : • Installation d'Oracle Clusterware version 10.2.0.1 • Modification de la valeur css misscount • Installation d'Oracle 10g Database avec Real Application Clusters 10.2.0.1 • Installation du correctif 10.2.0.1 • Configuration de l'écouteur • Création de la base de données initiale Installation d'Oracle Clusterware version 10.2.0.
7 Cliquez sur Next. La fenêtre Specify Network Interface Usage (Définir l'utilisation des interfaces réseau) affiche la liste des interfaces réseau du cluster. 8 Dans le menu déroulant Interface Type (Type d'interface), sélectionnez Public pour le type d'interface publique et Private pour le type d'interface privée (si nécessaire). Pour ce faire, sélectionnez Interface Name (Nom d'interface) et cliquez sur Edit (Modifier). Sélectionnez le type d'interface approprié et cliquez sur OK. 9 Cliquez sur Next.
Modification de la valeur css misscount 1 Arrêtez tous les nœuds, à l'exception du nœud 1. 2 Sur le nœud 1, ouvrez une fenêtre d'invite de commande. 3 Tapez la commande suivante et appuyez sur : cd %RACINE_ORA_CLUSTERWARE%\bin\ où %RACINE_ORA_CLUSTERWARE% correspond au répertoire racine créé à l'étape 4 de la section "Installation d'Oracle Clusterware version 10.2.0.1".
REMARQUE : le répertoire racine d'Oracle doit être différent de celui sélectionné lors de l'installation d'Oracle Clusterware. Vous ne pouvez pas installer Oracle Database 10g R2 Enterprise Edition 64 bits avec RAC dans le même répertoire home que celui utilisé pour Clusterware. 6 Cliquez sur Next. 7 Dans la fenêtre Specify Hardware Cluster Installation Mode (Définition du mode d'installation du cluster), cliquez sur Select All (Sélectionner tout), puis sur Next.
Installation du correctif REMARQUE : vous devez installer le correctif à partir du nœud sur lequel Oracle RAC 10g R2 est installé. Si vous ne vous trouvez pas sur ce nœud, quittez OUI et recommencez l'opération sur le nœud approprié. 1 Exécutez l'utilitaire OUI qui se trouve dans le dossier du correctif 2 Dans la fenêtre de bienvenue, cliquez sur Next.
5 Dans la fenêtre Summary (Récapitulatif), cliquez sur Install (Installer). Au cours de l'installation, il est possible que le message d'erreur suivant s'affiche : Error in writing to file oci.dll (Erreur d'écriture dans le fichier oci.dll). Pour contourner cet incident, procédez comme suit : a Annulez l'installation du correctif. b Renommez le répertoire %Oracle_home%\BIN en \bin_save. c Redémarrez le système. d Après le redémarrage, renommez \bin_save en \bin. e Exécutez le fichier setup.
5 Dans la fenêtre de bienvenue, cliquez sur Listener configuration (Configuration de l'écouteur), puis cliquez sur Next. 6 Dans la fenêtre Listener Configuration, Listener (Configuration de l'écouteur, Écouteur), sélectionnez Add (Ajouter), puis cliquez sur Next. 7 Dans la fenêtre Listener Configuration Listener Name (Configuration de l'écouteur, Nom de l'écouteur), sélectionnez le nom par défaut indiqué dans le champ Listener et cliquez sur Next.
4 Dans la fenêtre de bienvenue, sélectionnez Oracle Real Application Cluster Database (Base de données Oracle RAC), puis cliquez sur Next. 5 Dans la fenêtre Operations (Opérations), cliquez sur Create a Database (Créer une base de données), puis cliquez sur Next. 6 Dans la page Node Selection (Sélection des noeuds), cliquez sur Select All (Sélectionner tout), puis cliquez sur Next.
15 Dans la fenêtre Create Disk Group (Création d'un groupe de disques), entrez les informations relatives aux fichiers de la base de données. a Entrez un nom dans le champ Disk Group Name (Nom du groupe de disques). Exemple : DATABASE. b Dans la zone Redundancy (Redondance), sélectionnez External (Externe). c Cliquez sur Stamp Disks (Marquage des disques). d Sélectionnez Add or change label (Ajouter ou modifier un label) et cliquez sur Next.
18 Sélectionnez uniquement le nom du groupe de disques que vous avez affecté à la base de données à l'étape 15, puis cliquez sur Next. 19 Dans la fenêtre Database File Locations (Emplacement des fichiers de base de données), sélectionnez Use Oracle-Managed Files (Utiliser des fichiers gérés par Oracle), puis cliquez sur Next.
Informations supplémentaires Versions de logiciels prises en charge REMARQUE : les contrôleurs PCI Express ne sont pas pris en charge par cette configuration Dell pour Oracle. Le tableau 1-8 répertorie les logiciels pris en charge au moment de la publication du présent document. Pour obtenir la liste la plus récente des éléments matériels et logiciels pris en charge, rendez-vous à l'adresse dell.com/10g et téléchargez le document "Solution Deliverable List" (Liste des éléments pris en charge), version 1.1.
Dépannage Solutions en cas d'échec de l'installation de Clusterware Échec de l'assistant de configuration d'Oracle Clusterware Si l'installation échoue lorsque l'assistant de configuration d'Oracle Clusterware démarre dans la fenêtre Configuration Assistants (Assistants de configuration), procédez comme suit : 1 Ouvrez le fichier suivant : %RACINE_ORA_CLUSTERWARE%\cfgtoollogs\configToolFailedCommands où %RACINE_ORA_CLUSTERWARE% est le répertoire racine des services CRS créé à la section "Installation d'Ora
Désinstallation d'Oracle Clusterware La désinstallation d'Oracle Clusterware peut s'avérer nécessaire dans les cas suivants : • L'installation d'Oracle Clusterware a échoué. • L'installation de l'assistant de configuration n'a pas abouti. Pour désinstaller Oracle Clusterware, exécutez le programme d'installation OUI sur le nœud du cluster, supprimez tous les services Oracle restants, le cas échéant, et nettoyez la configuration des périphériques de stockage.
3 Redémarrez le nœud 1 et connectez-vous en tant qu'administrateur. 4 Redémarrez chacun des autres nœuds et connectez-vous en tant qu'administrateur. Nettoyage des périphériques de stockage 1 Nettoyez les partitions destinées à contenir le disque registre du cluster Oracle (OCRCFG) et le disque de vote. a Cliquez sur Démarrer et sélectionnez Exécuter. b Dans le champ Exécuter, tapez cmd et cliquez sur OK.
4 Tapez y et appuyez sur . 5 Démarrez Oracle GUI Object Manager. À l'invite, tapez la commande suivante et appuyez sur : %LecteurSystème%\ora_bin_utils\GUIOracleOBJManager.exe où %LecteurSystème% correspond au lecteur local de l'utilisateur. La fenêtre Oracle Object Manager s'affiche. 6 Supprimez les liens symboliques pour le disque OCR (OCRCFG) et le disque de vote (VOTEDSK). a Sélectionnez ocrcfg et votesdk. b Cliquez sur Options et sélectionnez Commit (Valider).
Procédures de dépannage supplémentaires Le tableau 1-9 indique les mesures recommandées en cas d'incident lié au déploiement et à l'utilisation de Windows Server 2003 et du logiciel Oracle Database 10g R2. Tableau 1-9. Dépannage Catégorie Incident/ Symptôme Cause Regroupem Échec du Le regroupement de NIC peut ent de regroupement de échouer dans les cas suivants : cartes NIC Broadcom • Un des NIC Broadcom utilisé dans réseau le regroupement est en panne ou désactivé.
Tableau 1-9. Dépannage (suite) Catégorie Incident/ Symptôme Cause Oracle Le nœud Le nœud ne peut pas communiquer Clusterware redémarre en avec les disques de stockage. affichant un écran bleu. Mesure recommandée Procédez comme suit : 1 Redémarrez le nœud. 2 Pendant l'auto-test de démarrage, appuyez sur . 3 Dans l'écran Menu d'options avancées de Windows, sélectionnez Mode sans échec. 4 Sélectionnez le système d'exploitation approprié. 5 Connectez-vous au système.
Tableau 1-9. Dépannage (suite) Catégorie Incident/ Symptôme Écran système bleu Les nœuds Les nœuds ne peuvent pas accéder au affichent un écran disque de vote. bleu. Cause Mesure recommandée 1 Vérifiez que les paramètres définissant le mode de connexion des cartes HBA dans le micrologiciel sont corrects par rapport à la configuration du stockage.
Tableau 1-9. Dépannage (suite) Catégorie Incident/ Symptôme Cause Mesure recommandée Stockage Lecteurs indisponibles. Les disques sont marqués comme étant indisponibles lorsque vous faites un clic droit sur Poste de travail, Gestion de l'ordinateur, puis Gestion des disques. Vérifiez que les unités logiques sont affectées aux deux nœuds. Vérifiez que les câbles à fibres optiques sont correctement connectés aux nœuds et aux systèmes de stockage.
Tableau 1-9. Dépannage (suite) Catégorie Incident/ Symptôme Cause Mesure recommandée VIPCA La configuration de VIPCA a échoué. Le nom d'interface de la carte du réseau public (ou, si la configuration comprend 4 interfaces réseau, l'interface réseau affectée à l'adresse IP virtuelle) est différent sur les deux nœuds. Assurez-vous que le nom d'interface de la carte du réseau public est identique sur les deux nœuds.
Obtention et utilisation de fichiers Open Source Le CD Dell Deployment comprend à la fois des programmes tiers et des programmes Dell. L'utilisation de ces logiciels est soumise aux conditions des contrats de licence des logiciels respectifs. Tous les logiciels désignés comme étant soumis aux conditions de la licence GPL GNU (GNU General Public License) peuvent être copiés, distribués et/ou modifiés en accord avec les termes et conditions de la licence GPL GNU, version 2 de juin 1991.
Guide de déploiement
Index A E O Agrégation de liens réseau, 116 Exemples Fibre Channel, connexions matérielles, 112 Obtention d'aide, 156 C Cluster Fibre Channel, exemple de connexion matérielle, 112 Configuration d'Oracle 10g, 111 vérification des configurations matérielle et logicielle, 111 Configuration des réseaux publics et privés, 115 Configuration du cluster Fibre Channel, 111 Configuration du réseau privé, 116 Configuration matérielle et logicielle requise, 108 Configurations matérielle et logicielle Fibre Channe
Index 160 Index
Dell PowerEdge-Systeme Oracle Database 10g Release 2 Enterprise Edition Real Application Cluster für Microsoft® Windows Server® 2003 Standard und Enterprise x64 R2 Edition Einrichtungsanleitung Version 1.1 w w w. d e l l . c o m | s u p p o r t . d e l l .
Anmerkungen und Hinweise ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, die die Arbeit mit dem Computer erleichtern. HINWEIS: Ein HINWEIS warnt vor möglichen Beschädigungen der Hardware oder vor Datenverlust und zeigt auf, wie derartige Probleme vermieden werden können. ___________________ Irrtümer und technische Änderungen vorbehalten. © 2006 Dell Inc. Alle Rechte vorbehalten. Die Reproduktion dieses Dokuments in jeglicher Form ohne schriftliche Genehmigung von Dell Inc.
Inhalt Software- und Hardwareanforderungen Lizenzverträge . . . . . Wichtige Dokumentation . . . . . . . . . . . . . . . . . 166 . . . . . . . . . . . . . . . . . . . . . . 167 167 . . . . . . . . . . . . . . . . . . . . . . Installation und Konfiguration des Betriebssystems . . . . . . . . . . . . Installation des Betriebssystems mit den Deployment-CDs . . . . . . 169 . . . . . . 169 . . . . . . 172 Konfiguration von Netzwerk und Speicher für Oracle RAC 10g R2 . . . . .
Installation des Patchsets 10.2.0.2 . . . . . . . . . . Installation der aktuellen Oracle-Patches . . . . . . Installation des Patches für das „Split Brain“-Problem beim Systemstart . . . . . . . . . . . . . . . . . . Konfiguration des Listeners . . . . . . . . . . . . . Erstellen der Startdatenbank. . . . . . . . . . . . . Weitere Informationen . . . . . . . . . . . . . . . . . . . . . . . . . . 205 205 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Dell Support . Oracle Support . . .
Dieses Dokument enthält Informationen zur Installation, Konfiguration, Neuinstallation und Verwendung der Software Oracle Database 10g R2 gemäß den von Dell für Oracle unterstützten Konfigurationen. Verwenden Sie dieses Dokument zusammen mit der Dell Deployment-CD, um die Software zu installieren. Wenn Sie das Betriebssystem nur mit den Betriebssystem-CDs installieren, treffen die Vorgehensweisen in diesem Dokument möglicherweise nicht auf Sie zu.
Software- und Hardwareanforderungen Tabelle 1-1 enthält die grundlegenden Softwareanforderungen für die von Dell für Oracle unterstützten Konfigurationen. In Tabelle 1-2 sind die Hardwareanforderungen aufgeführt. Ausführliche Angaben zu den erforderlichen Treiber- und Anwendungsversionen finden Sie unter „Unterstützte Softwareversionen“. Tabelle 1-1. Softwareanforderungen Softwarekomponente Konfiguration Microsoft Windows Server 2003 Standard/Enterprise x64 R2 Edition Oracle10g R2 Version 10.2.0.
Tabelle 1-2. Minimale Hardwareanforderungen – Fibre-Channel-Cluster– Konfiguration (Fortsetzung) Hardwarekomponente Konfiguration Fibre-Channel-Speichersystem Dell|EMC CX300, Informationen über unterstützte Konfigurationen finden Sie CX500, CX700, CX3-20, CX3-40 oder CX-80 unter dell.com/10g Gigabit-Ethernet-Switch (zwei) Informationen über unterstützte Konfigurationen finden Sie unter dell.com/10g Lizenzverträge ANMERKUNG: Die Dell-Konfiguration umfasst eine 30-Tage-Testlizenz der Oracle-Software.
3 Legen Sie die Dell Deployment-CDs und die Microsoft Windows Server 2003 Standard/Enterprise x64 R2 Edition-CDs bereit. 4 Schalten Sie das System ein. 5 Legen Sie die Dell Deployment CD1 in das CD-Laufwerk ein. Das System startet von der Dell Deployment CD1. Nach dem Start erscheint ein Textbildschirm mit der Aufforderung, eine Option zu wählen. Falls das System nicht von der Dell Deployment CD1 gestartet wurde, starten Sie das System neu.
Aktualisieren von Pfaden für temporäre Verzeichnisse Gehen Sie wie folgt vor, um sicherzustellen, dass die temporären Verzeichnisse Temp und Tmp korrekt gesetzt sind. 1 Klicken Sie auf Start und wählen Sie Ausführen. 2 Geben Sie im Feld Öffnen den Befehl cmd ein und klicken Sie auf OK. 3 Geben Sie an der Eingabeaufforderung die Zeile echo %Temp% ein und drücken Sie die : Der folgende Pfad wird angezeigt: %SystemDrive%\Temp wobei %SystemDrive% das lokale Laufwerk des Benutzers ist.
Abbildung 1-1. Hardwareverbindungen für einen SAN-verbundenen Fibre-Channel-Cluster Öffentliches Netzwerk Gb-Ethernet-Switches (privates Netzwerk) LAN/WAN PowerEdge-Systeme (Oracle-Datenbank) Dell | EMC Fibre-Channel-Switches (SAN) CAT 5e/6 (Kupfer-Gigabit-NIC) CAT 5e/6 (Kupfer-Gigabit-NIC) Glasfaserkabel Fibre-Channel-Speichersysteme Dell | EMC CX300, CX500, CX700, CX3-20, CX3-40 oder CX3-80 Tabelle 1-4.
Tabelle 1-4. Fibre-Channel-Hardwareverbindungen (Fortsetzung) Clusterkomponente Anschlüsse Jeder Dell|EMC FibreChannel-Switch Eine optische Verbindung von jedem SP zu einem HBA auf jedem PowerEdgeKnoten.
Verkabeln des Speichersystems für eine SAN-verbundene Konfiguration Abbildung 1-2.
Gehen Sie wie folgt vor, um das Oracle Cluster-Speichersystem für eine SAN-verbundene Konfiguration mit vier Ports zu verkabeln. 1 Installieren Sie ein Glasfaserkabel zwischen SP-A-Port 0 und Fibre-Channel-Switch 0. 2 Installieren Sie ein Glasfaserkabel zwischen SP-A-Port 1 und Fibre-Channel-Switch 1. 3 Installieren Sie ein Glaserfaserkabel zwischen SP-B-Port 0 und Fibre-Channel-Switch 1. 4 Installieren Sie ein Glaserfaserkabel zwischen SP-B-Port 1 und Fibre-Channel-Switch 0.
Konfiguration und Teaming des privaten Netzwerks Bevor Sie den Cluster einrichten, weisen Sie jedem Clusterknoten eine private IP-Adresse und einen Hostnamen zu. So ist gewährleistet, dass die Knoten über die private Schnittstelle miteinander kommunizieren können. Tabelle 1-7 zeigt ein Beispiel für eine Netzwerkkonfiguration bei einem Cluster mit zwei Knoten. ANMERKUNG: In diesem Beispiel wird davon ausgegangen, dass alle IP-Adressen in der hosts-Datei sämtlicher Clusterknoten registriert sind.
h Wählen Sie im Feld Select the adapters to include in this team (Adapter für dieses Team auswählen) die für das NIC-Teaming ausgewählten verbleibenden Netzwerkadapter, und klicken Sie auf Weiter. i Wählen Sie im Listenfeld Select a team mode (Team-Betriebsart wählen) die Option Adaptive Load Balancing (Adaptiver Lastausgleich). j Klicken Sie auf Finish (Fertig stellen), um das Teaming abzuschließen. k Klicken Sie im Fenster Team Properties (Team-Eigenschaften) auf OK.
l Klicken Sie im Fenster Broadcom Advanced Control Suite 2 auf Apply (Übernehmen). m Mit einer Warnmeldung wird darauf hingewiesen, dass die Netzwerkverbindung zeitweise unterbrochen wird. Klicken Sie zum Fortsetzen auf Yes (Ja). n Klicken Sie im Fenster IP address Setting Reminder (Erinnerung zum Festlegen der IP-Adresse) auf OK. o Klicken Sie im Fenster Broadcom Advanced Control Suite 2 auf OK. 5 Wiederholen Sie Schritt 1 bis Schritt 4 für die verbleibenden Knoten.
d Wählen Sie im Fenster Öffentliche Eigenschaften die Option Symbol bei Verbindung im Infobereich anzeigen. Nachdem Sie die in diesem Abschnitt erläuterten Schritte durchgeführt haben, wird der Status des Netzwerkadapters im Windows-Systembereich angezeigt. e Klicken Sie auf OK. f Klicken Sie im Fenster Eigenschaften auf Close (Schließen). g Wiederholen Sie Schritt a bis Schritt f für das private NIC-Team.
ANMERKUNG: Die IP-Adressen müssen nicht beim DNS-Server registriert zu werden, da die privaten IPNetzwerkadressen vom öffentlichen Netzwerk nicht zugänglich sind. 5 Stellen Sie sicher, dass die Clusterknoten mit den öffentlichen und privaten Netzwerken kommunizieren können. a Öffnen Sie ein Befehlszeilenfenster auf Knoten 1.
c Heben Sie im Bereich Select Disks to Convert (Datenträger für Konvertierung auswählen) die Auswahl für den/die in Schritt Schritt b markierten Datenträger auf, und klicken Sie auf Next (Weiter). ANMERKUNG: Auf diese Weise stellen Sie sicher, dass die Datenträger als Basis-Datenträger (Basic) konfiguriert werden. d Klicken Sie auf Finish (Fertig stellen). 6 Vergewissern Sie sich, dass im Fenster Disk Management (Datenträgerverwaltung) vier Datenträger angezeigt werden.
11 Klicken Sie auf dem Windows-Desktop mit der rechten Maustaste auf Arbeitsplatz, und wählen Sie Verwalten. 12 Blenden Sie Storage (Speicher) ein und klicken Sie anschließend auf Disk Management (Datenträgerverwaltung). Für jede im Speichersystem zugewiesene LUN wird ein Datenträger angezeigt. 13 Stellen Sie sicher, dass jede LUN als Basis-Datenträger (Basic) konfiguriert ist. 14 Wiederholen Sie Schritt 1 bis Schritt 13 für die verbleibenden Knoten.
6 Akzeptieren Sie im Fenster Specify Partition Size (Partitionsgröße festlegen) die vorgegebene Partitionsgröße und klicken Sie auf Next (Weiter). 7 Klicken Sie auf Finish (Fertig stellen). Der in Schritt 3 ausgewählte Partitionsbereich wird als erweiterte Partition konfiguriert. 8 Wiederholen Sie Schritt 3 bis Schritt 7 für alle freigegebenen Datenträger, die den Clusterknoten zugeordnet sind. 9 Erstellen Sie logische Laufwerke für den OCR-Datenträger.
Vorbereiten des Datenbankdatenträgers und des Wiederherstellungsbereichs für OCFS-Datenspeicherung In diesem Abschnitt ist beschrieben, wie logische Laufwerke für den OCFS-Speicherdatenträger (Oracle Clustered File System) erstellt werden. ANMERKUNG: Wenn Sie die logischen Laufwerke für den ASM-Speicherdatenträger erstellen (Automatic Storage Management), übergehen Sie die folgenden Schritte und lesen Sie „Vorbereiten des Datenbankdatenträgers und des Wiederherstellungsbereichs für ASM-Datenspeicherung“.
6 Entfernen Sie die zugewiesenen Laufwerkbuchstaben von den Speicherlaufwerken, die Sie in Schritt 1, Schritt 2 und in „Vorbereiten des OCR- und Voting-Datenträgers für Clusterware“ erstellt haben. a Klicken Sie mit der rechten Maustaste auf das logische Laufwerk und wählen Sie Change Drive Letter and Path (Laufwerkbuchstaben und Pfad ändern). b Wählen Sie im Fenster Change Drive Letter and Paths (Laufwerkbuchstaben und Pfade ändern) den Laufwerkbuchstaben aus und klicken Sie auf Next (Weiter).
3 Starten Sie alle anderen Knoten neu und melden Sie sich als Administrator an. 4 Klicken Sie auf dem Windows-Desktop der anderen Knoten mit der rechten Maustaste auf Arbeitsplatz und wählen Sie Verwalten. 5 Erweitern Sie im Fenster Computerverwaltung den Eintrag Datenspeicher und klicken Sie auf Datenträgerverwaltung.
• Installation des Patchsets 10.2.0.2 • Installation der aktuellen Oracle-Patches • Konfiguration des Listeners • Erstellen der Startdatenbank Installation von Oracle Clusterware Version 10.2.0.1 1 Legen Sie auf Knoten 1 die CD Oracle Clusterware 10g Release 2 for Microsoft Windows ein. Das Fenster Oracle Clusterware - Autorun wird angezeigt. Falls das Fenster Oracle Clusterware Autorun nicht erscheint: a Klicken Sie auf Start und wählen Sie Ausführen.
8 Falls erforderlich, ändern Sie den öffentlichen Interface Type (Schnittstellentyp) in Public (Öffentlich) (sofern als Private [Privat] angezeigt), indem Sie die folgenden Schritte durchführen: a Wählen Sie den Interface Name (Schnittstellennamen) aus und klicken Sie auf Edit (Bearbeiten). b Wählen Sie die korrekte Schnittstelle, und klicken Sie auf OK. 9 Klicken Sie im Fenster Specify Network Interface Usage (Nutzung der Netzwerkschnittstelle festlegen) auf Weiter.
13 Führen Sie im Fenster Cluster Configuration Storage (Clusterkonfigurationsspeicher) die folgenden Schritte für die Wiederherstellung durch: a Identifizieren Sie die Partition aus Schritt 2 im Abschnitt „Vorbereiten des Datenbankdatenträgers und des Wiederherstellungsbereichs für OCFS-Datenspeicherung“. b Wählen Sie die Partition aus, und klicken Sie auf Edit (Bearbeiten).
Ändern des Werts css misscount 1 Fahren Sie alle Knoten außer Knoten 1 herunter. 2 Öffnen Sie ein Befehlszeilenfenster auf Knoten 1. 3 Geben Sie an der Eingabeaufforderung die folgende Zeile ein, und drücken Sie dann die : cd %ORA_CLUSTERWARE_HOME%\bin\ wobei %ORA_CLUSTERWARE_HOME% das Stammverzeichnis ist, das Sie in Schritt 4 von „Installation von Oracle Clusterware Version 10.2.0.1“ festgelegt haben.
5 Überprüfen Sie im Fenster Specify Home Details (Stamm-Details festlegen) unter Destination (Ziel), dass die folgenden Einstellungen vorhanden sind: • Im Feld Name ist als Stammname der Oracle-Datenbank die Bezeichnung OraDb10g_home1 eingetragen. • Im Feld Pfad ist der folgende vollständige Oracle-Stammpfad eingetragen: %Systemlaufwerk%\oracle\product\10.2.0\db_1 wobei %Systemlaufwerk% das lokale Laufwerk des Benutzers ist.
Installation des Patchsets 10.2.0.2 für Oracle 10g Clusterware Bevor Sie beginnen 1 Halten Sie die „nodeapps“ auf allen Knoten an: %Systemlaufwerk%:\%CRS_HOME%\bin> srvctl stop nodeapps -n wobei %Systemlaufwerk% das lokale Laufwerk des Benutzers ist. 2 Halten Sie alle Oracle-Dienste auf sämtlichen Knoten an. Patchset-Installationsschritte ANMERKUNG: Sie müssen die Patchset-Software von dem Knoten aus installieren, auf dem Oracle RAC 10g R2 installiert wurde.
Patchset-Installationsschritte 1 Starten Sie das OUI-Installationsprogramm aus dem Patchset-Ordner. Zum Beispiel: %Systemlaufwerk%\Oracle_patch\setup.exe wobei %Systemlaufwerk% das lokale Laufwerk des Benutzers ist. 2 Klicken Sie im Begrüßungsfenster auf Weiter. 3 Wählen Sie im Fenster Specify home details (Stammdetails festlegen) den Namen OraDb10g_home1 aus dem Listenfeld und klicken Sie auf Weiter.
Konfiguration des Listeners In diesem Abschnitt werden die Schritte zum Konfigurieren des Listeners beschrieben, der benötigt wird, damit entfernte Clients Verbindung zu einer Datenbank aufnehmen können. Führen Sie auf Knoten 1 die folgenden Schritte aus: 1 Klicken Sie auf Start, wählen Sie Ausführen und geben Sie folgenden Befehl ein: netca 2 Klicken Sie auf OK.
Erstellen der Startdatenbank In diesem Abschnitt ist die Vorgehensweise zum Erstellen einer Startdatenbank mit OCFS sowie zum Überprüfen der Startdatenbank beschrieben. Führen Sie die folgende Schritte aus, um eine Startdatenbank mit OCFS zu erstellen: 1 Klicken Sie auf Knoten 1 auf Start, und wählen Sie Ausführen. 2 Geben Sie im Feld Ausführen den Befehl dbca ein, und klicken Sie auf OK: Der Database Configuration Assistant (Datenbankkonfigurationsassistent) wird gestartet.
13 Führen Sie im Fenster Recovery Configuration (Konfiguration für Wiederherstellung) folgende Schritte durch: a Wählen Sie Specify Flash Recovery Area (Flash-Wiederherstellungsbereich festlegen). b Klicken Sie auf Browse (Durchsuchen). c Wählen Sie im Fenster Directory Browse (Verzeichnis suchen) aus dem Listenmenü das CFSLaufwerk aus, dass in Schritt e von Schritt 13 im Abschnitt „Installation von Oracle Clusterware Version 10.2.0.1“ erstellt wurde. d Klicken Sie auf OK.
24 Notieren Sie sich die im Fenster Database Configuration Assistant (Datenbank-Konfigurationsassistent) angezeigten Informationen. Sie benötigen sie für die zukünftige Verwaltung der Datenbank. 25 Klicken Sie auf Exit (Beenden). Das Fenster Start Cluster Database (Clusterdatenbank starten) wird angezeigt, und die Clusterdatenbank startet. Installation von Oracle RAC 10g R2 mit ASM In diesem Abschnitt ist die Installation der Software Oracle RAC 10g R2 beschrieben.
6 Führen Sie im Fenster Cluster Configuration (Clusterkonfiguration) folgende Schritte durch: a Überprüfen Sie den öffentlichen, privaten und virtuellen Hostnamen für den primären Knoten. b Wenn Sie diese Werte ändern wollen, klicken Sie auf Edit (Bearbeiten), geben Sie die gewünschten Werte ein, und klicken Sie auf OK. c Klicken Sie auf Add (Hinzufügen). d Geben Sie den öffentlichen, privaten und virtuellen Hostnamen für den zweiten Knoten ein, und klicken Sie auf OK. 7 Klicken Sie auf Weiter.
14 Klicken Sie im Fenster Summary (Übersicht) auf Install (Installieren), um den Installationsvorgang zu starten. ANMERKUNG: Wenn bei der Ausführung des Konfigurationsassistenten Fehler auftreten, lesen Sie „Umgehen von Fehlern bei der Clusterware-Installation“ im Abschnitt "Fehlerbehebung" in diesem Dokument. Im Fenster Install wird der Fortschritt der Installation angezeigt.
2 Klicken Sie auf OK, um fortzufahren. Das Installationsprogramm Oracle Universal Installer (OUI) wird gestartet und der Begrüßungsbildschirm wird angezeigt. 3 Klicken Sie auf Weiter. 4 Klicken Sie im Fenster Select Installation Type (Installationstyp auswählen) auf Standard Edition und anschließend auf Next (Weiter).
Installation des Patchsets 10.2.0.2 für Oracle 10g Clusterware Vorbereitungen 1 Halten Sie die „nodeapps“ auf allen Knoten an. Geben Sie den folgenden Befehl ein und drücken Sie die : %Systemlaufwerk%:\%CRS_HOME%\bin> srvctl stop nodeapps -n wobei %Systemlaufwerk% das lokale Laufwerk des Benutzers ist. 2 Halten Sie alle Oracle-Dienste auf sämtlichen Knoten an.
Patchset-Installationsschritte 1 Starten Sie das OUI-Installationsprogramm im Patchset-Ordner. 2 Klicken Sie im Begrüßungsfenster auf Weiter. 3 Wählen Sie im Fenster Specify home details (Stammdetails festlegen) den Namen OraDb10g_home1 aus dem Listenfeld, um das Patchset im Oracle-Stammverzeichnis zu installieren, und klicken Sie dann auf Weiter. 4 Klicken Sie im Fenster Specify Hardware Cluster Installation Mode (Hardware-ClusterInstallationsmodus festlegen) auf Weiter.
Konfiguration des Listeners In diesem Abschnitt werden die Schritte zum Konfigurieren des Listeners beschrieben. Dieser ist erforderlich, damit Clients aus dem Netzwerk eine Verbindung zu einer Datenbank aufnehmen können. Führen Sie die folgenden Schritte auf Knoten 1 aus: 1 Klicken Sie auf Start, wählen Sie Ausführen und geben Sie netca ein: 2 Klicken Sie auf OK.
Erstellen der Startdatenbank Führen Sie die folgende Schritte aus, um mit Oracle ASM eine Startdatenbank zu erstellen: 1 Stellen Sie sicher, dass Oracle Clusterware aktiv ist. a Öffnen Sie ein Fenster mit einer Befehlszeile. Klicken Sie auf Start und wählen Sie Ausführen. Geben Sie cmd ein und drücken Sie die . b Geben Sie crsctl check crs ein.
11 Wählen Sie im Fenster Storage Options (Speicheroptionen) die Option Automatic Storage Management (ASM) (Automatische Speicherverwaltung [ASM]), und klicken Sie anschließend auf Weiter. 12 Führen Sie im Fenster Create ASM Instance (ASM-Instanz erstellen) die folgenden Schritte durch: a Geben Sie im Feld SYS password (SYS-Kennwort) ein neues Kennwort ein und bestätigen Sie es im dafür vorgesehenen Feld.
17 Geben Sie im Fenster Create Disk Group (Datenträgergruppe erstellen) die Informationen für den Wiederherstellungsbereich ein. a Geben Sie im Feld Disk Group Name (Name der Datenträgergruppe) einen Namen für die Datenträgergruppe ein. Beispiel: FLASH. b Wählen Sie im Feld Redundancy (Redundanz) den Eintrag External (Extern) aus. c Klicken Sie auf Stamp Disks (Datenträger kennzeichnen). d Wählen Sie Add or change label (Kennzeichnung hinzufügen/ändern), und klicken Sie auf Weiter.
f Klicken Sie auf Edit Archive Mode Parameters (Archivmodusparameter bearbeiten). • g Stellen Sie im Fenster Edit Archive Mode Parameters (Archivmodusparameter bearbeiten) sicher, dass der Pfad unter Archive Log Destinations (Archivprotokollziele) wie folgt eingestellt ist: +FLASH/, wobei FLASH der Datenträgergruppenname für den Wiederherstellungsbereich aus Schritt a von Schritt 17 ist. Klicken Sie auf Weiter. 21 Klicken Sie im Fenster Database Content (Datenbankinhalt) auf Next (Weiter).
Tabelle 1-8. Unterstützte Softwareversionen (Fortsetzung) Softwarekomponente Unterstützte Versionen QLogic HBA Storport-Treiber 9.1.2.15 Emulex HBA Storport-Treiber 7-.1.11.3 PERC 5/i Integrated RAID Controller 1.18.0.64 PERC 4e/Di und PERC 4e/Si 6.46.3.64 Intel 1000 MT/XT (Basistreiber) 8.4.21.0 Intel PRO PCIe Gigabit-Adapterreihe 9.4.24.1 Intel PROSet (für NIC-Teaming) 10.2.78.5 Broadcom BCM95701, BCM95703, BCM95703s und 8.48.0.
Fehler mit Konfigurationsassistent für virtuelle private IP Wenn im VIPCA-Assistent während der Installation von Oracle Clusterware ein Fehler auftritt, wird eventuell folgende Meldung angezeigt: Virtual Private IP Configuration Assistant failed Führen Sie in diesem Fall die folgenden Schritte durch, um den Fehler zu umgehen. Dieser Vorgang ist ausführlich im Metalink-Artikel 338924.1 beschrieben.
6 Klicken Sie im Fenster Welcome (Willkommen) auf Cancel (Abbrechen). 7 Klicken Sie nach Aufforderung auf Cancel (Abbrechen) und anschließend auf Yes (Ja). Löschen von Oracle-Diensten 1 Starten Sie auf Knoten 1 die Services-Konsole. a Klicken Sie auf Start und wählen Sie Ausführen. b Geben Sie im Feld Ausführen den nachstehenden Befehl ein und klicken Sie auf OK: services.msc Das Fenster Services (Dienste) wird angezeigt.
2 Vergewissern Sie sich, dass OCRCFG und VOTEDSK in der Datei aufgeführt sind. Wenn OCRCFG und VOTEDSK nicht in der Datei aufgeführt sind, ordnen Sie OCRCFG und VOTEDSK den vorgesehenen Laufwerken zu und speichern Sie die Datei. Importieren Sie die symbolischen Verknüpfungen mit dem Oracle Symbolic Link Importer (ImportSYMLinks) in die zugeordneten Speicherlaufwerke (OCRCFG and VOTEDSK).
7 Starten Sie die Computerverwaltungskonsole. a Klicken Sie auf dem Windows-Desktop auf Start und wählen Sie Ausführen. b Geben Sie im Feld Ausführen den nachstehenden Befehl ein und drücken Sie die : compmgmt.msc Das Fenster Computerverwaltung wird angezeigt. 8 Löschen Sie die ASM- oder OCFS-Partitionen. a Klicken Sie im Fenster Computer Management Console auf Storage (Datenspeicher) und klicken Sie auf Disk Management (Datenträgerverwaltung).
Weitere Maßnahmen zur Fehlerbehebung Tabelle 1-9 enthält empfohlene Maßnahmen für Probleme, die beim Einrichten und beim Einsatz von Windows Server 2003 und Oracle Database 10g R2 auftreten können. Tabelle 1-9. Fehlerbehebung Kategorie Problem/ Anzeichen Ursache Empfohlene Maßnahmen NICTeaming Broadcom NICTeaming schlägt fehl Folgende Schritte können zu einem Fehler beim NIC-Teaming führen: • Einer der für das NIC-Teaming verwendeten Broadcom-NICs ist ausgefallen oder deaktiviert.
Tabelle 1-9. Fehlerbehebung (Fortsetzung) Kategorie Problem/ Anzeichen Ursache Oracle Beim Neustart des Der Clusterknoten kann nicht mit Clusterware Clusterknotens den Speicherlaufwerken wird ein blauer kommunizieren. Bildschirm angezeigt. 212 Einrichtungsanleitung Empfohlene Maßnahmen Gehen Sie wie folgt vor: 1 Starten Sie den Clusterknoten neu. 2 Drücken Sie während des Einschaltselbsttests (POST) die Taste . 3 Wählen Sie im Menü für erweiterte Windows-Optionen den Abgesicherten Modus.
Tabelle 1-9. Fehlerbehebung (Fortsetzung) Kategorie Problem/ Anzeichen Ursache Blauer Die Die Clusterknoten können nicht auf Systembilds Clusterknoten den Voting-Datenträger zugreifen. chirm zeigen einen blauen Bildschirm an. Empfohlene Maßnahmen 1 Stellen Sie sicher, dass die Firmwareeinstellungen für den HBAVerbindungsmodus für die Speicherkonfiguration korrekt konfiguriert sind.
Tabelle 1-9. Fehlerbehebung (Fortsetzung) Kategorie Problem/ Anzeichen Speicher Datenträger Wenn Sie auf dem Windowserscheinen als Desktop mit der rechten Maustaste nicht zugänglich. auf Arbeitsplatz klicken, Computerverwaltung wählen und dann auf Datenträgerverwaltung klicken, werden die Datenträger als nicht zugänglich angezeigt. Ursache Empfohlene Maßnahmen Überprüfen Sie, ob die LUNs der Speicherlaufwerke beiden Clusterknoten zugewiesen sind.
Tabelle 1-9. Fehlerbehebung (Fortsetzung) Kategorie Problem/ Anzeichen Ursache Empfohlene Maßnahmen VIPCA Die VIPCAKonfiguration schlägt fehl. Der Name des öffentlichen Netzwerkadapters (bzw. – bei 4 Netzwerkschnittstellen – der Name der Netzwerkschnittstelle für die virtuelle IP-Adresse) ist nicht auf beiden Clusterknoten identisch. Stellen Sie sicher, dass der Name des öffentlichen Netzwerkadapters auf beiden Clusterknoten identisch ist.
Erwerb und Einsatz von Open-Source-Dateien Die auf der Deployment-CD enthaltene Software umfasst sowohl Programme von Fremdanbietern als auch Programme von Dell. Die Verwendung der Software unterliegt den jeweils angegebenen Lizenzbestimmungen. Alle mit „Under the terms of the GNU GPL“ (gemäß den Bedingungen der GNU GPL) gekennzeichneten Softwarekomponenten dürfen gemäß den Bedingungen der GNU General Public License in der Version 2 vom Juni 1991 kopiert, verteilt und/oder modifiziert werden.
Index B H L Beispiele Fibre-Channel-Cluster, Hardwareverbindungen, 170 Hardware Fibre-Channel-Cluster, minimale Anforderungen, 166 Fibre-ChannelVerbindungen, 170 Lizenzverträge, 167 Bonding (Bündelung), 174 C Cluster Fibre-ChannelHardwareverbindungen, Beispiel, 170 Cluster einrichten Fibre-Channel, 169 D Dokumentation, 167 F Fehlerbehebung, 206 Fibre-Channel-Cluster einrichten, 169 Hardware- und Softwarekonfigurationen Fibre-Channel, 171 O Öffentliches Netzwerk Konfiguration, 173 Oracle RAC 10g I
Index U Überprüfen Hardwarekonfiguration, 169 Softwarekonfiguration, 169 Unterstützte Speichergeräte, 205 W Wie Sie Hilfe bekommen, 215 Z Zusätzliche Informationen, 205 218 Index
Dell™ PowerEdge™ システム Oracle Database 10g Release 2 Enterprise Edition Real Application Cluster for Microsoft® Windows Server® 2003 Standard x64 R2 Edition およ び Enterprise x64 R2 Edition 導入ガイドバージョン 1.1 w w w. d e l l . c o m | s u p p o r t . d e l l .
メモおよび注意 メモ:コ ン ピ ュ ー タ を 使 い や す く す る た め の 重 要 な 情 報 を 説 明 し て い ま す 。 注意:ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明してい ます。 ___________________ 本書の内容は予告なく変更されることがあります。 © 2006 すべての著作権は Dell Inc. にあります。 Dell Inc. の書面による許可のない複製は、いかなる形態においても厳重に禁じられています。 本書に使用されている商標:Dell、DELL ロゴ、および PowerEdge は Dell Inc.
目次 ソフトウェアおよびハードウェアの要件 ライセンス契約 . . 重要なマニュアル . . . . . . . . . . . . . . . . 224 . . . . . . . . . . . . . . . . . . . . . . . . 225 225 . . . . . . . . . . . . . . . . . . . . . . . . OS のインストールと設定 . . . . . . . . . . . . . . . . . . . . . . . 『Deployment CD』を使用した OS のインストール. . . . . . . . . クラスタのハードウェアおよびソフトウェアの構成の確認 . . . . . ファイバーチャネルクラスタのセットアップ . . . . . . . SAN 接続構成に用いるストレージシステムのケーブル接続 . Oracle RAC 10g R2 用のネットワークおよびストレージの構成 . . . 228 228 231 . . . . 232 . . . .
システム起動中のスプリットブレイン問題に対応するた めのパッチのインストール . . . . . . . . . . . . . . . . リスナーの構成 . . . . . . . . . . . . . . . . . . . . . . シードデータベースの作成 . . . . . . . . . . . . . . . . 追加情報 . . . . 258 258 259 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 サポートされるソフトウェアのバージョン トラブルシューティング 困ったときは . 262 . . . . . . . . . . . . . . . . . . . . . . . 263 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
本書では、Oracle をサポートするデルの構成に従って、Oracle Database 10g R2 ソフトウェアをイ ンストール、設定、再インストール、および使用するのに必要な情報について説明します 本書と『Dell Deployment CD』を併用して、使用するソフトウェアをインストールしてください。 再インストール用 CD のみを使用して OS をインストールする場合、本書の手順は該当しないこと があります。 内容は次のとおりです。 • ソフトウェアおよびハードウェアの要件 • Microsoft® Windows Server® 2003 Enterprise/Standard x64 R2 Edition のインストールおよ び設定手順 • クラスタのハードウェアおよびソフトウェアの構成の確認 • Oracle Database Real Application Clusters (RAC) 10g R2 のネットワークおよびストレージの 構成 • Oracle Database RAC 10g R2 10.2.0.
ソフトウェアおよびハードウェアの要件 デルがサポートする Oracle の設定の基本的なソフトウェア要件の一覧を 表 1-1 に示します。 表 1-2 は、ハードウェアの要件の一覧です 最低限必要なドライバとアプリケーションのバージョンの詳細については、「サポートされるソフ トウェアのバージョン」を参照してください。 表 1-1 ソフトウェア要件 ソフトウェアコンポーネント 構成 Microsoft Windows Server 2003 Standard/Enterprise x64 R2 Edition Oracle10g R2 バージョン 10.2.0.1 Enterprise Edition(クラスタのための RAC オプションを含む) EMC® PowerPath®(ファイバー チャネルクラスタの場合のみ) バージョン 4.
表 1-2 ハードウェアの最小要件 ― ファイバーチャネルクラスタの構成 (続き) ハードウェアコンポーネント 構成 Dell|EMC CX300、CX500、CX700、CX3-20、 サポートされる構成については、dell.com/10g を参照 CX3-40、または CX-80 ファイバーチャネルスト してください。 レージシステム ギガビットイーサネットスイッチ(2 台) サポートされる構成については、dell.
『Deployment CD』を使用した OS のインストール メモ:BIOS、ファームウェア、およびドライバのアップデート版については、デルサポートサイト support.dell.
13 画面の指示に従って、インストールを完了します。 メモ:この処理には数分かかることがあります インストール手順が完了すると、Windows へようこそ ウィンドウが表示されます 14 取り外した外付けストレージデバイスすべてをシステムに取り付けます。 15 Windows へようこそ ウィンドウが表示されたら、 を押して続行します。 16 ログオン ウィンドウが表示されます 17 パスワード フィールドに 手順 12 で設定した管理者パスワードを入力して、OK をクリックし ます。 一時ディレクトリパスのアップデート 次の手順に従って、ディレクトリ Temp および Tmp へのパスが正しく設定されていることを確認 します 1 スタート をクリックし、ファイル名を指定して実行 を選択します 2 名前 フィールドに cmd と入力し、OK をクリックします。 3 コマンドプロンプトで、echo %Temp% と入力し、 を押します。 次のパスが表示されます。 %SystemDrive%\Temp %SystemDrive% はユーザーのローカルドライブで
クラスタのハードウェアおよびソフトウェアの構成の確認 クラスタのセットアップを開始する前に、ハードウェアの取り付け、パブリックとプライベートの インタフェース、ノードソフトウェアが正しく設定されていることを確認します。以下の項では、 ファイバーチャネルクラスタのセットアップについて説明します。 ファイバーチャネルクラスタのセットアップ デルの公認技術者がファイバーチャネルクラスタのセットアップを終えたら、本項の説明に従って ハードウェアの接続およびハードウェアとソフトウェアの構成を確認してください。 ストレージエリアネットワーク(SAN)接続のファイバーチャネルクラスタ(ノード 2 つ)に必要 なクラスタ接続を 図 1-1、図 1-2、および 表 1-4 に示します。 図 1-1 SAN 接続のファイバーチャネルクラスタ用のハードウェア接続 パブリックネットワーク ギガビットイーサネットスイッチ (プライベートネットワーク) LAN/WAN PowerEdge システム (Oracle データベース) Dell | EMC ファイバーチャネル スイッチ(SAN) CAT 5e/6(銅線 Gigabit
表 1-4 ファイバーチャネルハードウェアの相互接続 クラスタのコンポーネント 接続 各 PowerEdge システム ノード CAT 5e/6 ケーブル 1 本をパブリック NIC から LAN に接続 CAT 5e/6 ケーブル 1 本をプライベートギガビット NIC からギガビットイーサ ネットスイッチに接続(プライベートネットワーク) CAT 5e/6 ケーブル 1 本を冗長プライベートギガビット NIC から冗長ギガビッ トイーサネットスイッチに接続(プライベートネットワーク) 光ケーブル 1 本をオプティカル HBA 0 からファイバーチャネルスイッチ 0 と、 HBA 1 からスイッチ 1 へそれぞれ接続 各 Dell|EMC ファイバーチャ CAT 5e/6 ケーブル 2 本を LAN に接続(各ストレージプロセッサ(SP)から) ネルストレージシステム SAN 接続または直接接続の構成で、各ファイバーチャネルスイッチに 1 ~ 4 本の光ケーブルで接続。 詳細については、「SAN 接続構成に用いるストレージシステムのケーブル接 続」を参照してください。 各 Dell|EMC ファイバ
システムハードウェアおよびソフトウェアの構成 • • • 各ノードには、少なくとも以下のハードウェア周辺機器が含まれている必要があります。 – 内蔵ハードドライブベイの 2 台のハードドライブ(73 GB 以上) – ギガビット NIC ポート 3 個 – HBA 2 個(PowerEdge 1850 システムと 1950 システムの場合はデュアルポート HBA 1 個) 各ノードには、以下のソフトウェアをインストールする必要があります。 – Windows Server 2003, Standard/Enterprise x64 R2 Edition(表 1-1 を参照) – HBA ドライバ ファイバーチャネルストレージは、LUN を 3 つ以上作成し、クラスタに割り当てて構成する必 要があります。 表 1-5 LUN の設定とサイズ LUN 最小サイズ パーティションの数 用途 1 1 GB 2(120 MB と 50 MB) 投票ディスク、Oracle 2 データベースよりも大き いこと 1 3 2 番目の LUN のサイズの 1 2 倍以上 C
SAN 接続構成に用いるストレージシステムのケーブル接続 図 1-2 SAN 接続のファイバーチャネルクラスタのケーブル接続 クラスタノード 1 0 1 クラスタノード 2 HBA ポート(2) HBA ポート(2) sw0 0 1 sw1 SP-A SP-B CX3-20 ストレージシステム Oracle クラスタストレージシステムを 4 ポートの SP SAN 接続で構成するには、以下の手順を実行 します。 1 1 本の光ファイバーケーブルを SP-A ポート 0 からファイバーチャネルスイッチ 0 に接続します。 2 1 本の光ファイバーケーブルを SP-A ポート 1 からファイバーチャネルスイッチ 1 に接続します。 3 1 本の光ファイバーケーブルを SP-B ポート 0 からファイバーチャネルスイッチ 1 に接続します。 4 1 本の光ファイバーケーブルを SP-B ポート 1 からファイバーチャネルスイッチ 0 に接続します。 5 1 本の光ファイバーケーブルをノード 1 の HBA0 からファイバーチャネルスイッチ 0 に接続し ます。 6 1 本の光ファイバーケーブル
7 1 本の光ファイバーケーブルを各追加ノードの HBA0 からファイバーチャネルスイッチ 0 に接 続します。 8 1 本の光ファイバーケーブルを各追加ノードの HBA1 からファイバーチャネルスイッチ 1 に接 続します。 Oracle RAC 10g R2 用のネットワークおよびストレージの構成 本項では、ファイバーチャネルクラスタのセットアップについて説明します。内容には、以下の手 順が含まれています。 • パブリックおよびプライベートネットワークの設定。 • ストレージ構成の確認。 • Oracle Clusterware および Oracle データベース用の共有ストレージの構成。 メモ:Oracle RAC 10g R2 は、順序化された一連の手順を必要とする複雑なデータベース設定です。 ネットワークとストレージを最小限の時間で設定するには、以下の手順を順番に実行してください。 パブリックおよびプライベートネットワークの設定 メモ:クライアント接続および接続のフェイルオーバーのために、固有のパブリックおよびプライ ベートインターネットプロトコル(IP)アドレスを 1 つと、仮想 I
プライベートネットワークの設定とチーミング クラスタを展開する前に、各クラスタノードにプライベート IP アドレスとホスト名を割り当てま す。この手順により、ノードがプライベートインタフェースを通じて確実に通信できるようになり ます。 2 ノードクラスタのネットワーク設定の例を 表 1-7 に示します。 メモ:この例では、すべてのクラスタノードのホストファイルにすべての IP アドレスが登録されて います。 表 1-7 ネットワーク設定の例 ホスト名 タイプ IP アドレス 登録 rac1 パブリック 155.16.170.1 %SystemRoot%\system32\drivers\etc\hosts rac2 パブリック 155.16.170.2 %SystemRoot%\system32\drivers\etc\hosts rac1-vip 仮想 155.16.170.201 %SystemRoot%\system32\drivers\etc\hosts rac2-vip 仮想 155.16.170.
i チームモードの選択 リストボックスで、アダプティブロードバランシングを選択します。 j 完了をクリックしてチーミングを完了します。 k Team Properties(チームのプロパティ)ウィンドウで OK をクリックします。 l Intel NIC's Properties(Intel NIC のプロパティ)ウィンドウで、OK をクリックします m コンピュータの管理ウィンドウを閉じます。 4 ノード 1 が Broadcom NIC で構成されている場合は、次の手順で NIC のチーミングを設定しま す。それ以外の場合は 手順 5 に進みます a スタート → プログラム → Broadcom→ Broadcom Advanced Control Suite 2 の順に クリックします。 Broadcom Advanced Control Suite 2 ウィンドウが表示されます。 b ツール をクリックし、チームの作成 を選択します。 Broadcom Teaming Wizard(Broadcom チーミングウィザード)ウィンドウが表示さ れます。 c 次へ をクリッ
l Broadcom Advanced Control Suite 2 ウィンドウで、適用 をクリックします。 m ネットワーク接続が一時中断することを警告する情報メッセージが表示されます。はい を クリックして続行します。 n IP address Setting Reminder(IP アドレス設定のリマインダー)ウィンドウで OK を クリックします。 o Broadcom Advanced Control Suite 2 ウィンドウで、OK をクリックします。 5 残りのノードで 手順 1 ~ 手順 4 を繰り返します。 パブリックおよびプライベートネットワークアダプタ用の IP アドレスの設定 メモ:このソリューションでは、TIE 対応 NIC の TOE 機能はサポートされません。 1 必要に応じて、アダプタのネットワークインタフェース名をアップデートします。それ以外の 場合は、手順 3 に進みます。 a ノード 1 で スタート をクリックし、設定 → コントロールパネル → ネットワーク接続 の順 に選択します。 b ネットワーク接続 ウィンドウで、名前を変更するパブリ
f プロパティ ウィンドウで、閉じる をクリックします。 g プライベート NIC チームで 手順 a ~手順 f を繰り返します。 メモ:プライベート NIC チームでは、デフォルトゲートウェイアドレスと DNS サーバー項目は 不要です。 h 残りのノードで 手順 a ~ 手順 g を繰り返します。 3 パブリックおよびプライベートネットワークアダプタが、ネットワークサービスによってアク セスできる適切な順序で表示されていることを確認します a スタート → 設定 → コントロールパネル → ネットワーク接続 の順にクリックします。 b ネットワーク接続 ウィンドウで 詳細 をクリックし、詳細設定 を選択します c アダプタとバインド タブを選択します。 d ネットワークアダプタが次の順序で表示されていることを確認します パブリック プライベート < その他のネットワークアダプタ > メモ:アダプタの順序を変更するには、上下の矢印をクリックしてください。 e OK をクリックします。 f ネットワーク接続 ウィンドウを閉じます。 4 両方のノードで、%SystemRoo
5 クラスタノードがパブリックおよびプライベートネットワークと通信できることを確認します。 a ノード 1 で、コマンドプロンプトウィンドウを開きます。 b コマンドプロンプトで、次のコマンドを入力します。 ping ping と は、もう 1 つのノードにおけるパブリック およびプライベートネットワークアダプタのホスト名です。 ノードのネットワークアダプタが ping コマンドに反応しない場合は、ネットワーク設定 を確認し、この手順を繰り返します。 メモ:仮想インターネットプロトコル(VIP)の設定は後で行われます。この時点では ping コマ ンドによる確認ができません。 6 手順 1 ~手順 5 を残りのクラスタノードで繰り返します。 Dell|EMC に必要なホストベースソフトウェアのインストール Dell|EMC のマニュアルの手順に従って、Dell|EMC システムに付属の EMC Navisphere® Agent ソ フトウェアを
6 ディスクの管理 ウィンドウで、4 台のディスクが表示されていることを確認します。ディスク のサイズは互いに、また、ストレージシステム内のノードに割り当てられている LUN ともほ ぼ同一であるはずです。 7 手順 1 ~ 手順 6 を残りのクラスタノードで繰り返します PowerPath のインストール 1 ノード 1 で、EMC PowerPath をインストールします メモ:詳細については、Dell|EMC ストレージシステムに付属の Dell|EMC PowerPath のマニュアル を参照してください。 2 インストール手順が完了したら、システムを再起動します。 3 残りのノードで 手順 1 と 手順 2 を繰り返します PowerPath の機能の確認 1 Windows デスクトップでシステムトレイを探し、PowerPath の三角形のアイコンを右クリッ クし、PowerPath Administrator を選択します。 2 PowerPathAdmin コンソールで、EMC PowerPathAdmin を展開します。 3 左ウィンドウペインで、パス管理 を展開します。 4 左ウィン
Oracle Clusterware 用のディスクの準備 本項では、以下のディスク用に論理ドライブを作成するための情報を提供します。 • OCR ディスク ― クラスタ設定情報が格納されています。 • 投票ディスク(Voting Disk)― 1 つまたは複数のノードでプライベートネットワークまたは 接続ストレージが使用できない場合に、クラスタノード間にアービトレーションを提供します。 • データディスクとバックアップディスク ― データベースを作成し(データディスク)、バッ クアップとログデータを保存する(バックアップディスク)ためのストレージ領域を提供し ます。 本書で説明されているクラスタ設定を行う際に、ファイバーチャネルストレージ上にパーティショ ンを作成します。パーティションの作成時には、接続されているストレージシステム内に作成され た LUN または論理ディスクをクラスタノードが検出できることを確認します Oracle Clusterware 用のディスクを準備するには、OCR ディスク、投票ディスク、データディス ク、およびフラッシュリカバリ領域ディスクを確認します。適切なディスクが
9 OCR ディスク用に論理ドライブを作成します。 a OCR と投票ディスク(1 GB LUN)用として識別されたディスクのパーティション領域で 空き領域を右クリックし、新しい論理ドライブ を選択します。 新しいパーティションウィザードへようこそ が表示されます。 b 次へ をクリックします。 c パーティションの種類を選択 ウィンドウで 論理ドライブ を選択し、次へ をクリックし ます。 d パーティションサイズの指定 ウィンドウの パーティションサイズ(MB) フィールドに 120 と入力し、次へ をクリックします e ドライブ文字またはパスの割り当て ウィンドウで、ドライブ文字またはドライブパスを割 り当てない を選択し、次へ をクリックします。 f パーティションのフォーマット ウィンドウで、このパーティションをフォーマットしない を選択し、次へ をクリックします。 g 完了 をクリックします。 10 投票ディスク用の論理ドライブを作成します。 a パーティション領域で空き領域を右クリックし、新しい論理ドライブ を選択します。 新しいパーティションウィザードへようこそ
OCFS を使用したデータベースストレージ用のデータベースディスクとフラッシュリカバリ領域の準備 本項では、OCFS(Oracle Clustered File System)ストレージディスクの作成に使用する論理ドライ ブの作成方法について説明します。 メモ:自動ストレージ管理(ASM)ストレージディスクの作成に使用する論理ドライブを作成する場 合は、次の手順を省略して、「ASM を使用したデータベースストレージ用のデータベースディスクと フラッシュリカバリ領域の準備」を参照してください。 1 ノード 1 で、データベース用に 1 つの論理ドライブを作成します。 a Oracle データベースに割り当てられたディスクを確認します。 b ディスクパーティション領域で空き領域を右クリックし、新しい論理ドライブ を選択し ます。 新しいパーティションウィザードへようこそ が表示されます。 c 次へ をクリックします。 d パーティションの種類を選択 ウィンドウで 論理ドライブ を選択し、次へ をクリックし ます。 e パーティションサイズの指定 ウィンドウの パーティションサイズ(MB) フィ
ASM を使用したデータベースストレージ用のデータベースディスクとフラッシュリカバリ領域の準備 本項では、ASM ディスクストレージの作成に使用する論理ドライブの作成方法について説明しま す。ASM ディスクストレージは、複数のディスクへのスパニングが可能な 1 つまたは複数のディス クグループで構成されています。 メモ:OCFS ストレージディスクの作成に使用する論理ドライブを作成する場合は、次の手順を省略 して、「OCFS を使用したデータベースストレージ用のデータベースディスクとフラッシュリカバリ領 域の準備」の手順に従ってください。 1 データベース用に 1 つの論理ドライブを作成します。 a Oracle データベースに割り当てられたディスクを確認します。 b ディスクパーティション領域で空き領域を右クリックし、新しい論理ドライブ を選択し ます。 新しいパーティションウィザードへようこそ が表示されます。 c 次へ をクリックします。 d パーティションの種類を選択 ウィンドウで 論理ドライブ を選択し、次へ をクリックし ます。 e パーティションサイズの指定 ウィンドウで
共有ディスクの 自動マウント オプションの有効化 1 ノード 1 で スタート をクリックし、ファイル名を指定して実行 を選択します。 2 ファイル名を指定して実行 フィールドに cmd と入力し、OK をクリックします 3 コマンドプロンプトで diskpart と入力し、 を押します。 4 DISKPART コマンドプロンプトで automount enable と入力し、 を押します。 次のメッセージが表示されます。 Automatic mounting of new volumes enabled.
Oracle Clusterware バージョン 10.2.0.1 のインストール 1 ノード 1 で CD ドライブに『Oracle Clusterware 10g Release 2 for Microsoft Windows CD』 をセットします。 Oracle Clusterware - Autorun(Oracle Clusterware ― 自動実行)ウィンドウが表示され ます。Oracle Clusterware - Autorun(Oracle Clusterware ― 自動実行)ウィンドウが表 示されない場合は、以下の手順を実行します。 a スタート をクリックし、ファイル名を指定して実行 を選択します。 b ファイル名を指定して実行 フィールドに次のテキストを入力し、OK をクリックします。 %CD-ROM drive%:\autorun\autorun.
9 Specify Network Interface Usage(ネットワークインタフェースの用途を指定する)ウィ ンドウで、次へ をクリックします。 10 Cluster Configuration Storage(クラスタ構成ストレージ)ウィンドウで、各 OCR ディス クについて次の手順を実行します。 a 手順 「Clusterware 用の OCR と投票ディスクの準備」で作成した 120 MB パーティション の位置を確認します。 b パーティションを選択し、編集 をクリックします。 c Specify Disk Configuration(ディスク構成の指定)ウィンドウで、Place OCR (Primary) on this partition(このパーティションに OCR(プライマリ)を置く)を選択し、OK を クリックします。 11 Cluster Configuration Storage(クラスタ構成ストレージ)ウィンドウで、各投票ディス クについて以下の手順を実行します a 手順 「Clusterware 用の OCR と投票ディスクの準備」で作成した 50 MB パー
d Use partition for data storage(パーティションをデータストレージに使用する)が選 択されていることを確認します。 e Assign Drive Letter(ドライブ文字の割り当て)オプションのプルダウンメニューを使 用して、ドライブ文字をパーティションに割り当てます。 f OK をクリックします。 14 Cluster Configuration Storage(クラスタ構成ストレージ)ウィンドウで 次へ をクリック します。 15 警告メッセージを無視して OK をクリックします。 16 サマリー ウィンドウで インストール をクリックしてインストール手順を開始します。 インストール ウィンドウにインストールの進行状況が表示されます。 次に、Configuration Assistant ウィンドウが表示され、OUI が一連の設定ツールを実行し ます。 次に、インストールの終了 ウィンドウが表示されます。 メモ:ディスクパーティション領域を右クリックしないでください。Configuration Assistant ウィ ンドウでエラーが発生した場合は、以下の
Oracle Database 10g R2 with Real Application Clusters 10.2.1 のインストール 1 ノード 1 で CD ドライブに『Oracle Database 10g Release 2 for Microsoft Windows CD』 をセットします。 Oracle Database 10g - Autorun(Oracle Database 10g ― 自動実行)ウィンドウが表示さ れます。Oracle Database 10g - Autorun(Oracle Database 10g― 自動実行)ウィンドウ が表示されない場合は、以下の手順を実行します。 a スタート をクリックし、ファイル名を指定して実行 を選択します。 b ファイル名を指定して実行 フィールドに次のテキストを入力し、OK をクリックします。 %CD-ROM drive%:\autorun\autorun.
9 構成オプションの選択 ウィンドウで データベースソフトウェアのみインストール を選択し、 次へ をクリックします。 10 サマリー ウィンドウで インストール をクリックします。 11 インストールの終了 ウィンドウで、ウィンドウに表示されている手順を実行します。 メモ:次の手順に進む前に、このウィンドウに表示されている手順を実行する必要があります。 12 インストールの終了 ウィンドウの表示に従って必要な手順を実行したら、終了 をクリックし ます。 13 終了 ウィンドウで、はい をクリックします。 パッチセット 10.2.0.2 のインストール メモ:以下の手順でパッチセットをインストールしても、インストールされるのは、お使いのシステ ム上でまだ作成されていないシードデータベース付きの 10.2.0.1 データベースバイナリと 10.2.0.1 Clusterware のような Oracle ソフトウェアに限られます。 1 metalink.oracle.com からパッチセット 10.2.0.
5 サマリー ウィンドウで インストール をクリックします。 6 インストールの終了 ウィンドウで、サマリー ウィンドウに表示されている手順を 手順 1 を除 いてすべて実行します 7 インストールの終了 ウィンドウで 終了 をクリックし、はい をクリックして OUI を終了します。 Oracle 10g Database 用のパッチセット 10.2.0.2 のインストール メモ:リスナーとシードデータベースを作成する前に、次の手順を完了します。すべての Oracle サー ビスが実行中であることを確認してください メモ:パッチセットソフトウェアのインストールは、Oracle RAC 10g R2 ソフトウェアをインストール したノードから行う必要があります。そのノードが OUI を実行しているノードと異なる場合は、終了 して、そのノードからパッチセットをインストールします。 パッチセットのインストール手順 1 パッチセットのフォルダにある OUI を起動します たとえば、次のように入力します:%SystemDrive%\Oracle_patch\setup.
最新の Oracle パッチのインストール 1 ウェブブラウザを開きます 2 Oracle Metalink のウェブサイト metalink.oracle.com に移動します。 3 インストールに関連のあるパッチをダウンロードします システム起動中のスプリットブレイン問題に対応するためのパッチのインストール 1 patch5059258 と表示されているフォルダに移動します。 2 opmd.exe ファイルをすべてのノードの %CRS_HOME%\bin ディレクトリにコピーします 3 コマンドプロンプトに次を入力します。 %SystemDrive%\%CRS_HOME%\bin> ompd.
シードデータベースの作成 本項では、OCFS を使用してシードデータベースを作成する手順とシードデータベースを確認する手 順について説明します。シードデータベース OCFS を使用してシードデータベースを作成するには、次の手順を実行します。 1 ノード 1 で スタート をクリックし、ファイル名を指定して実行 を選択します。 2 ファイル名を指定して実行 フィールドに dbca と入力し、OK をクリックします。 Database Configuration Assistant が起動します。 3 ようこそ ウィンドウで Oracle Real Application Cluster データベース を選択し、次へ をク リックします。 4 操作 ウィンドウで、データベースの作成 をクリックし、次へ をクリックします。 5 ノードの選択 ウィンドウで すべて選択 をクリックし、次へ をクリックします。 6 データベーステンプレート ウィンドウで、カスタムデータベース をクリックし、次へ をクリッ クします。 7 データベース識別情報 ウィンドウの グローバルデータベース名 フィールドに、racdb などの 名前
13 リカバリ構成 ウィンドウで、以下の手順を実行します。 a フラッシュリカバリ領域の指定 を選択します。 b 参照 をクリックします。 c ディレクトリの参照 ウィンドウで、プルダウンメニューを使用して、「Oracle Clusterware バージョン 10.2.0.
ASM を使用した Oracle RAC 10g R2 のインストール 本項では、Oracle RAC 10g R2 ソフトウェアのインストール手順について説明します。 内容は次のとおりです。 • Oracle Clusterware バージョン 10.2.0.1 のインストール • css misscount 値の変更 • Oracle10g Database with Real Application Clusters 10.2.0.1 のインストール • パッチセット 10.2.0.1 のインストール • リスナーの構成 • シードデータベースの作成 Oracle Clusterware バージョン 10.2.0.
7 次へ をクリックします Specify Network Interface Usage(ネットワークインタフェースの用途を指定する)ウィ ンドウが表示され、クラスタ全体のネットワークインタフェースの一覧が表示されます 8 インタフェースタイプ ドロップダウンメニューで、(必要に応じて)Interface Name(イン タフェース名)を選択し、編集 をクリックすることで、パブリックの インタフェースタイプ を Public、プライベートの インタフェースタイプ を Private に設定します。正しいインタ フェースタイプ を選択し、OK をクリックします。 9 次へ をクリックします。 10 Cluster Configuration Storage(クラスタ構成ストレージ)画面で、OCR ディスクについ て以下の手順を実行します。 a 「Clusterware 用の OCR と投票ディスクの準備」で作成した 120 MB パーティションの位 置を確認します。 b パーティションを選択し、編集 をクリックします。 c Specify Disk Configuration(ディスク構成の指定)ウ
css misscount 値の変更 1 ノード 1 以外のすべてのノードをシャットダウンします。 2 ノード 1 で、コマンドプロンプトウィンドウを開きます。 3 コマンドプロンプトで次のテキストを入力し、 を押します。 cd %ORA_CLUSTERWARE_HOME%\bin\ %ORA_CLUSTERWARE_HOME% は、「Oracle Clusterware バージョン 10.2.0.1 のインストー ル」の 手順 4 で作成したホームディレクトリです。 4 コマンドプロンプトで次のテキストを入力し、 を押します。 crsctl set css misscount 120 5 ノード 1 を再起動し、管理者としてログインします。 6 他のすべてのノードを起動します。 Oracle10g Database with Real Application Clusters 10.2.0.
6 次へ をクリックします。 7 ハードウェアのクラスタインストールモードの指定 ウィンドウで すべて選択 をクリックし、 次へ をクリックします。 8 製品固有の前提条件のチェック ウィンドウで、次へ をクリックします。 9 構成オプションの選択 ウィンドウで データベースソフトウェアのみインストール を選択し、 次へ をクリックします。 10 サマリー ウィンドウで インストール をクリックします。 11 インストールの終了 ウィンドウで、表示されている手順を実行します。 メモ:次の手順に進む前に、このウィンドウに表示されている手順を実行する必要があります 12 終了 をクリックします パッチセット 10.2.0.2 のインストール メモ:以下の手順でパッチセットをインストールしても、インストールされるのは、お使いのシステ ム上でまだ作成されていないシードデータベース付きの 10.2.0.1 データベースバイナリと 10.2.0.1 Clusterware のような Oracle ソフトウェアに限られます。 1 Oracle Metalink のウェブサイト metalink.oracle.
5 サマリー ウィンドウで インストール をクリックします。 6 インストールの終了 ウィンドウで、サマリー ウィンドウに表示されている手順を 手順 1 を除 いてすべて実行します 7 インストールの終了 画面で 終了 をクリックし、はい をクリックして OUI を終了します。 Oracle 10g Database 用のパッチセット 10.2.0.
システム起動中のスプリットブレイン問題に対応するためのパッチのインストール 1 patch5059258 と表示されているフォルダに移動します。 2 opmd.exe ファイルをすべてのノードの %CRS_HOME%\bin ディレクトリにコピーします 3 コマンドプロンプトに次を入力します。 %SystemDrive\%CRS_HOME%\bin> ompd.exe -install %SystemDrive% はユーザーのローカルドライブです。 4 すべてのノードで 手順 3 を繰り返します。 リスナーの構成 本項では、リモートクライアントからデータベースに接続するために必要なリスナーの構成手順に ついて説明します 次の手順をノード 1 で実行します 1 スタート をクリックし、ファイル名を指定して実行 を選択して、netca.
シードデータベースの作成 Oracle ASM を使用してシードデータベースを作成するには、次の手順を実行します。 1 Oracle Clusterware が実行中であることを確認します。 a コマンドプロンプトウィンドウを開きます。スタート をクリックし、ファイル名を指定し て実行 を選択して、cmd と入力し、 を押します。 b crsctl check crs と入力します。 c 画面に次の情報が出力されます。 CSS appears healthy CRS appears healthy EVM appears healthy(CSS は正常です。) d 上記のメッセージが表示されない場合は、crsctl start crs と入力します。 e exit と入力することで、cmd ウィンドウを閉じます。 2 ノード 1 で スタート をクリックし、ファイル名を指定して実行 を選択します 3 ファイル名を指定して実行 フィールドに次のテキストを入力し、OK をクリックします dbca Database Configuration Assistant が起動します 4
12 ASM インスタンスの作成 ウィンドウで、以下の手順を実行します。 a SYS パスワード フィールドで、新しいそれぞれ適切なフィールドに新しいパスワードの入 力と確認の入力を行います。 b 初期化パラメータファイル(IFILE)の作成 を選択します。 c 次へ をクリックします。 13 Database Configuration Assistant ウィンドウで、OK をクリックします。 ASM Creation(ASM の作成)ウィンドウが表示され、ASM インスタンスが作成されます。 メモ:Failed to retrieve network listener resources(ネットワークリスナーリ ソースの読み出しに失敗しました)という警告メッセージが表示された場合は、はい をクリック して DBCA に適切なリスナーリソースの作成を許可します。 14 ASM ディスクグループ ウィンドウで、新規作成 をクリックします。 15 ディスクグループの作成 ウィンドウで、データベースファイルの情報を入力します。 a ディスクグループ名 フィールドに、新しいディスクグループの名前
f Generate stamps with this prefix(この接頭辞を持つスタンプを生成する)フィール ドで、FLASH と入力し、次へ をクリックします。 g Stamp disks(ディスクにスタンプする)ウィンドウで、次へ をクリックします。 h 完了 をクリックして設定を保存します。 i 利用可能なディスクの隣にあるチェックボックスを選択し、OK をクリックします。 ASM ディスクグループ ウィンドウが表示され、ソフトウェアがディスクグループを作成中で あることが示されます 作成が完了したら、FLASH ディスクグループが ディスクグループ名 行に表示されます 18 手順 15 でデータベースに割り当てたディスクグループ名のみを選択し、次へ をクリックし ます 19 データベースファイルの位置 ウィンドウで、Oracle Managed Files の使用 を選択し、次へ をクリックします。 20 リカバリ構成 ウィンドウで、以下の手順を実行します。 a フラッシュリカバリ領域の指定 を選択します。 b 参照 をクリックします。 c 手順 17 で作成した FL
メモ:この処理には数分かかることがあります 作成が完了すると、Database Configuration Assistant ウィンドウにデータベース設定情 報が提供されます 27 Database Configuration Assistant ウィンドウ内の情報をメモします。情報は将来のデー タベース管理に使用します 28 終了 をクリックします クラスタデータベースの起動 ウィンドウが表示され、クラスタデータベースが起動します 追加情報 サポートされるソフトウェアのバージョン メモ:今回のリリースに含まれる Oracle をサポートするデルの設定では、PCI Express コントローラは サポートされていません リリース時点でサポートされているソフトウェアの一覧を 表 1-8 に示します。サポートされている 最新のハードウェアとソフトウェアについては、dell.com/10g からバージョン 1.
トラブルシューティング Clusterware のインストールに失敗した場合の対処法 Oracle Clusterware Configuration Assistant のエラー Oracle Clusterware Configuration Assistant を使用したインストールが失敗した場合は、 Configuration Assistant ウィンドウで以下の手順を実行します。 1 ファイル %ORA_CLUSTERWARE_HOME%\cfgtoollogs\configToolFailedCommands を 開きます。%ORA_CLUSTERWARE_HOME% は、「Oracle Clusterware バージョン 10.2.0.
Oracle Clusterware のアンインストール 以下の問題が発生した場合は、解決のために Oracle Clusterware のアンインストールが必要な場合 があります。 • Oracle Clusterware のインストールが失敗した。 • Configuration Assistant が正常にインストールできなかった。 Oracle Clusterware をアンインストールするには、クラスタノードで OUI を実行し、残っている Oracle サービスをすべて削除し、ストレージデバイスをクリーンにします OUI の実行 1 ノード 1 で Explorer のウィンドウを開き、次のディレクトリに移動します。 %SystemDrive%\oracle\product\10.2.0\crs\oui\bin %SystemDrive% はユーザーのローカルドライブです。 2 setup.
3 ノード 1 を再起動し、管理者としてログインします。 4 その他の各ノードを再起動し、管理者としてログインします。 ストレージデバイスをクリーンにする方法 1 OCR レジストリ(OCRCFG)と投票ディスク用に設定するパーティションをクリーンにします a スタート をクリックし、ファイル名を指定して実行 を選択します。 b ファイル名を指定して実行 フィールドに cmd と入力し、OK をクリックします。 c コマンドプロンプトで次のテキストを入力し、 を押します。 %SystemDrive%\oracle\product\10.2.0\crs\bin\ExportSYMLink %SystemDrive% はユーザーのローカルドライブです。 Oracle Symbolic Link Exporter(ExportSYMLink)によって、シンボリックリンクが SYMMAP.TBL ファイルから現在のディレクトリにインポートされます。 d コマンドプロンプトで次のテキストを入力し、 を押します。 notepad SYMMAP.
5 Oracle GUI Object Manager を起動します。 コマンドプロンプトで次のテキストを入力し、 を押します。 %SystemDrive%\ora_bin_utils\GUIOracleOBJManager.
トラブルシューティングのその他の問題 Windows Server 2003 OS と Oracle 10g R2 ソフトウェアを導入して使用する際に発生する可能性 のある問題について、推奨する対処方法を 表 1-9 に示します。 表 1-9 トラブルシューティング カテゴリ 問題 / 症状 NIC のチー Broadcom NIC ミング のチーミングに エラーが発生す る。 原因 推奨する対応処置 NIC のチーミングにエラーが発生 すると、以下の事象が順に起こる 場合がある。 • NIC のチーミングで使用された Broadcom NIC の 1 つにエラー が発生するか、または無効にな る。2 番目の NIC が利用できる ため、プライベートネットワー クは 2 番目の NIC の働きによ り、このノード上で依然として 有効である。 • 1 番目の NIC がまだダウンして いるか、無効な時に、チーミン グ内の 2 番目の NIC にもエラー が発生するか、または無効にな る。この場合、このノードのプ ライベートネットワークは完全 にダウンする。このノードのプ ライベート IP アドレスは
表 1-9 トラブルシューティング (続き) カテゴリ 問題 / 症状 原因 推奨する対応処置 Oracle Clusterware のインス トール Oracle Clusterware の インストールが 失敗する。 OCRCFG や VOTEDSK のシムリ ンクが使用できない。 以下の手順を実行します。 1 OUI を使用して Oracle Clusterware をアンインストールします。 2 残りの Oracle サービスをすべてアン インストールします。 3 ストレージデバイスをクリーンにし ます。 Configuration 1 台または複数のストレージデバ Assistant が正常 イスを再フォーマットする必要が にインストール ある。 できない。 268 導入ガイド 詳細については、「Oracle Clusterware のアンインストール」を参照してくだ さい。
表 1-9 トラブルシューティング (続き) カテゴリ 問題 / 症状 Oracle クラスタノード Clusterware が再起動して画 面が青色(ブ ルースクリー ン)になる。 原因 推奨する対応処置 クラスタノードがストレージディ スクと通信できない。 以下の手順を実行します。 1 クラスタノードを再起動します。 2 POST 中に を押します。 3 Windows 詳細オプションメニュー 画面で セーフモード を選択します。 4 適切な OS を選択します。 5 システムにログオンします。 6 デスクトップ 画面で OK をクリックし ます。 7 Windows デスクトップで マイコン ピュータ を右クリックし、管理 を選 択します。 8 コンピュータの管理 ウィンドウで、 サービスとアプリケーション を展開し ます。 9 サービス をクリックします。 10 最初の Oracle サービスを右クリック し、プロパティ を選択します。 11 スタートアップ ドロップダウンメニュー をクリックし、このサービスのデフォ ルトのスタートアップの種類を記録し ます。 12 スタートアッ
表 1-9 トラブルシューティング (続き) カテゴリ 問題 / 症状 システムの クラスタノード 青色の画面 で画面が青色に なる。 原因 クラスタノードが投票ディスクに アクセスできない。 推奨する対応処置 1 HBA 接続モードのファームウェアが ストレージ構成に対して適切に設定さ れていることを確認します。 クラスタノードとストレージシステム が直接接続構成になっている場合は、 接続 モードを 0 - loop only(0 - ルー プのみ)に設定します。 クラスタノードとストレージシステム がファイバーチャネルスイッチを介し て相互に接続されている場合は、接続 モードを 2 - loop preferred, otherwise point-to-point(2 - ルー プ優先、ループが不可の場合はポイン トツーポイント)に設定します。 2 問題が解決しない場合は、CSS misscount を 120 よりも大きな値にし ます。 3 以下の手順を実行します。 a ノード 1 以外のすべてのノードを シャットダウンします。 b ノード 1 で、コマンドプロンプトを 開きます。 c 以下
表 1-9 トラブルシューティング (続き) カテゴリ 問題 / 症状 ストレージ ディスクがアク セスできないも のとして表示さ れる。 原因 推奨する対応処置 Windows デスクトップで マイコ ンピュータ を右クリックし、コン ピュータの管理 を選択し、ディス クの管理 をクリックすると、ディ スクがアクセスできないものとし て表示される。 両方のクラスタノードにストレージ LUN が割り当てられていることを確認 します。 クラスタノードとストレージシステム を接続する光ファイバーケーブルが正 しく取り付けられていることを確認し ます 考えられる原因 • LUN がクラスタノードに割り当 詳細については、「SAN 接続構成に用 てられていない。 いるストレージシステムのケーブル接 • ケーブル接続が正しくない。 続」を参照してください • クラスタノードに HBA ドライバ がインストールされていない。 ストレージ SCSI ディスクデ Windows デスクトップで マイコ 両方のクラスタノードにストレージ バイスが表示さ ンピュータ を右クリックし、コン LUN が割り当てられてい
表 1-9 トラブルシューティング (続き) 272 カテゴリ 問題 / 症状 VIPCA VIPCA の設定が パブリックネットワークのアダプ 失敗する。 タインタフェース(または 4 ネッ トワークインタフェースの場合 は、VIP 用に割り当てられたネッ トワークインタフェース)の名前 が、両方のクラスタノードで同一 でない。 導入ガイド 原因 推奨する対応処置 パブリックネットワークのアダプタイ ンタフェース名が両方のクラスタノー ドで同一であることを確認します パブリックネットワークのアダプタイ ンタフェース名を確認するには、以下 の手順を実行します。 1 ノード 1 で スタート をクリックし、 設定 → コントロールパネル → ネット ワーク接続 の順に選択します。 2 ネットワーク接続 ウィンドウで、名前 を変更するパブリックネットワークア ダプタを右クリックし、名前の変更 を 選択します。 3 残りの各ノードで 手順 1 および 手順 2 を繰り返します
困ったときは デルサポート システムの使い方の詳細については、システムコンポーネントに付属のマニュアルを参照してくだ さい。各種の白書、デルがサポートする設定、一般情報については、dell.com/10g を参照してく ださい。ハードウェアおよび OS ソフトウェアに対するデルのテクニカルサポート、アップデート のダウンロードについては、デルサポートサイト support.dell.com を参照してください。デルへ のお問い合わせ先については、システムに付属の『インストール & トラブルシューティング』に記 載されています。 デルでは、企業向けのトレーニングと資格認証を実施しております。詳細については、 dell.com/training を参照してください。なお、トレーニングサービスを提供していない地域があ りますのでご了承ください。 Oracle のサポート Oracle ソフトウェアおよびアプリケーションクラスタウェアのトレーニング、および Oracle への お問い合わせの方法については、Oracle のウェブサイト oracle.
導入ガイド
索引 O く は Oracle 10g の設定 , 228 ハードウェアおよびソフト ウェアの構成の確認 , 228 クラスタ ファイバーチャネルのハー ドウェア接続例 , 228 ハードウェア ファイバーチャネルクラス タの最小要件 , 224 ファイバーチャネルの相互 接続 , 229 Oracle RAC 10g インストール , 253 ネットワークおよびスト レージの構成 , 232 クラスタのセットアップ ファイバーチャネル , 228 こ 困ったときは , 273 R Red Hat Enterprise Linux インストール , 225 さ サポートされるストレージデ バイス , 262 そ ソフトウェア 要件 , 224, 262 ソフトウェアおよびハード ウェアの要件 , 224 か 確認 ソフトウェアの構成 , 228 ハードウェアの構成 , 228 パブリックおよびプライベー トネットワークの設定 , 232 パブリックネットワーク 設定 , 232 ふ い インストール Oracle RAC 10g, 253 Red Hat Enterprise L
ç ௠ら ライセンス契約 , 225 れ 例 ファイバーチャネルクラス タ用のハードウェア接続 , 228 276 索引
Sistemas Dell™ PowerEdge™ Base de datos Oracle 10g Versión 2 Enterprise Edition Real Application Cluster para Microsoft® Windows Server® 2003 Standard Edition y Enterprise x64 R2 Edition Guía de implantación versión 1.1 w w w. d e l l . c o m | s u p p o r t . d e l l .
Notas y avisos NOTA: una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. AVISO: un AVISO indica la posibilidad de daños en el hardware o la pérdida de datos, e informa de cómo evitar el problema. ___________________ La información contenida en este documento puede modificarse sin previo aviso. © 2006 Dell Inc. Reservados todos los derechos. Queda estrictamente prohibida la reproducción de este documento en cualquier forma sin la autorización por escrito de Dell Inc.
Contenido Requisitos de software y hardware . Contratos de licencia . . . Documentación importante . . . . . . . . . . . . . . . . . . . 282 . . . . . . . . . . . . . . . . . . . . . 283 283 . . . . . . . . . . . . . . . . . . . . . Instalación y configuración del sistema operativo . . . . . . . . . . . . 283 Instalación del sistema operativo mediante los CD de implantación. . . . . 284 Verificación de las configuraciones de hardware y software del clúster . . . . 285 . . 285 . . 288 . .
Instalación del patchset 10.2.0.2 . . . . . . . . . . . . . . . Instalación de los parches de Oracle más recientes . . . . . Instalación del parche para "split brain" durante el inicio del sistema Configuración del proceso de escucha . . . . . . . . . . . . Creación de la base de datos semilla . . . . . . . . . . . . . Información adicional . . . . 314 315 315 316 317 . . . . . . . . . . . . . . . . . . . . . . . . . . 320 321 . . . . . . 321 322 326 . . . . . . . . . . . . . . . . . . . . . . . . .
En este documento se proporciona información para instalar, configurar, reinstalar y utilizar el software de base de datos Oracle 10g R2 de acuerdo con las configuraciones de Oracle admitidas por Dell. Utilice este documento junto con el CD de implantación de Dell para instalar el software. Si instala el sistema operativo utilizando únicamente los CD del sistema operativo, los pasos descritos en este documento pueden no ser aplicables.
Requisitos de software y hardware En la tabla 1-1 se enumeran los requisitos básicos de software para las configuraciones de Oracle admitidas por Dell, y en la tabla 1-2 se enumeran los requisitos de hardware. Para obtener información detallada sobre las versiones mínimas de software que pueden utilizarse con los controladores y las aplicaciones, consulte "Versiones de software admitidas". Tabla 1-1.
Tabla 1-2. Requisitos mínimos de hardware: Configuración de cluster Fibre Channel (continuación) Componentes de hardware Configuración Dell|EMC CX300, CX500, CX700, CX3-20, Para obtener información sobre las configuraciones admitidas, Sistema de almacenamiento CX3-40 o CX-80 Fibre visite dell.com/10g. Channel Conmutador Ethernet Gigabit (dos) Para obtener información sobre las configuraciones admitidas, visite dell.com/10g.
Instalación del sistema operativo mediante los CD de implantación NOTA: para obtener las actualizaciones más recientes del BIOS, el firmware y los controladores, visite la página web de asistencia de Dell (support.dell.com). 1 Apague el sistema. 2 Desconecte todos los dispositivos de almacenamiento externos del sistema. 3 Consulte los CD de implantación de Dell y el CD Microsoft Windows Server 2003 Standard/Enterprise x64 R2 Edition. 4 Encienda el sistema.
14 Vuelva a conectar todos los dispositivos de almacenamiento externos al sistema. 15 En la ventana de bienvenida a Windows, pulse para continuar. 16 Aparece la ventana Iniciar sesión. 17 En el campo Contraseña, escriba la contraseña de administrador que creó en el paso 12 y haga clic en Aceptar. Actualización de las rutas de directorios temporales Siga estos pasos para verificar que las rutas de acceso a los directorios Temp y Tmp se han establecido correctamente.
Figura 1-1. Conexiones de hardware para un clúster Fibre Channel de conexión mediante SAN Red pública Conmutadores Ethernet Gb (red privada) LAN/WAN Sistemas PowerEdge (base de datos Oracle) Conmutadores Dell | EMC Fibre Channel (SAN) CAT 5e/6 (NIC Gigabit de cobre) CAT 5e/6 (NIC Gigabit de cobre) Cables de fibra óptica Sistemas de almacenamiento Dell | EMC CX300, CX500, CX700, CX3-20, CX3-40 o CX3-80 Fibre Channel Tabla 1-4.
Tabla 1-4.
Tabla 1-5. Tamaños y configuración del LUN LUN Tamaño mínimo Número de particiones Uso 1 1 GB 2 (120 MB y 50 MB) Disco de votación, registro del software de clúster Oracle (OCR) 2 Más grande que la base de datos 1 3 Como mínimo, dos veces 1 más grande que el segundo LUN Espacio en disco Área de recuperación flash Cableado del sistema de almacenamiento para una configuración de conexión mediante SAN Figura 1-2.
Utilice el procedimiento siguiente para configurar el sistema de almacenamiento de clúster Oracle en una configuración de conexión mediante SAN de SP de cuatro puertos. 1 Conecte un cable óptico del puerto 0 SP-A al conmutador 0 Fibre Channel. 2 Conecte un cable óptico del puerto 1 SP-A al conmutador 1 Fibre Channel. 3 Conecte un cable óptico del puerto 0 SP-B al conmutador 1 Fibre Channel. 4 Conecte un cable óptico del puerto 1 SP-B al conmutador 0 Fibre Channel.
En función del número de puertos NIC disponibles, configure las interfaces pública y privada tal como se muestra en la tabla 1-6. Tabla 1-6.
d Haga clic con el botón derecho del ratón en la NIC Intel identificada para la agrupación de NIC y seleccione Propiedades. e Haga clic en la ficha Teaming (Agrupación). f Seleccione Team with other Adapters (Agrupar con otros adaptadores) y, a continuación, seleccione New Team (Grupo nuevo). g Especifique un nombre para el grupo de NIC y haga clic en Next (Siguiente).
h En la ventana Designating Standby Member (Designación de miembro en espera), seleccione Do not configure a Standby Member (No crear un miembro en espera) y haga clic en Next (Siguiente). i En la ventana Configuring Live Link (Configuración de enlace activo), seleccione No y haga clic en Next (Siguiente). j En la ventana Creating/Modifying a VLAN (Creación/Modificación de una VLAN), seleccione No y haga clic en Next (Siguiente).
c Haga clic en Usar la siguiente dirección IP, especifique la dirección IP necesaria, la dirección de puerta de enlace predeterminada y la dirección IP del servidor DNS, y haga clic en Aceptar. d En la ventana de propiedades de Público, seleccione Mostrar icono en el área de notificación al conectar. Una vez realizados los procedimientos descritos en esta sección, se mostrará el estado del adaptador de red en la bandeja del sistema. e Haga clic en Aceptar.
155.16.170.201 rac1-vip 155.16.170.202 rac2-vip NOTA: no es necesario registrar las direcciones IP con el servidor DNS, ya que no se puede acceder a las direcciones IP de la red privada desde la red pública. 5 Asegúrese de que los nodos del clúster pueden comunicarse con las redes pública y privada. a En el nodo 1, abra una ventana de indicador de comandos.
c En la ventana Seleccione los discos que desea convertir, deseleccione los discos que ha seleccionado en el paso b y haga clic en Siguiente. NOTA: este procedimiento asegura que los discos estén configurados como Básico. d Haga clic en Finalizar. 6 En la ventana Administración de discos, compruebe que aparezcan cuatro discos. Los discos deben ser de tamaño similar entre ellos y respecto a los LUN que están asignados a los nodos en el sistema de almacenamiento.
12 Expanda Almacenamiento y haga clic en Administración de discos. Aparece un disco por cada LUN asignado en el almacenamiento. 13 Asegúrese de que todos los LUN están configurados como disco Básico. 14 Repita del paso 1 al paso 13 en los nodos restantes. Preparación de los discos para el software de clúster Oracle En esta sección se proporciona información para crear unidades lógicas para los discos siguientes: • Disco OCR: contiene información de configuración del clúster.
9 Cree unidades lógicas para el disco OCR. a En el área de partición del disco identificado para OCR y el disco de votación (LUN de 1 GB), haga clic con el botón derecho del ratón en el espacio libre y seleccione Unidad lógica nueva. Aparece la ventana Éste es el Asistente para partición nueva. b Haga clic en Siguiente. c En la ventana Seleccionar el tipo de partición, seleccione Unidad lógica y haga clic en Siguiente.
1 En el nodo 1, cree una unidad lógica para la base de datos. a Localice el disco asignado para la base de datos Oracle. b En el área de partición de disco, haga clic con el botón derecho del ratón en el espacio libre y seleccione Unidad lógica nueva. Aparece la ventana Éste es el Asistente para partición nueva. c Haga clic en Siguiente. d En la ventana Seleccionar el tipo de partición, seleccione Unidad lógica y haga clic en Siguiente.
Preparación del disco de base de datos y el área de recuperación flash para el almacenamiento de base de datos con ASM En esta sección se proporciona información para crear las unidades lógicas que se utilizarán para la creación del almacenamiento en disco ASM. El almacenamiento en disco ASM se compone de uno o más grupos de discos que pueden abarcar varios discos.
Activación de la opción Automount (Montaje automático) para los discos compartidos 1 En el nodo 1, haga clic en Inicio y seleccione Ejecutar. 2 En el campo Ejecutar, escriba cmd y haga clic en Aceptar. 3 En el indicador de comandos, escriba diskpart y pulse . 4 En el indicador de comandos de DISKPART, escriba automount enable y pulse . Aparece el mensaje siguiente: Montaje automático de nuevos volúmenes habilitado. 5 En el indicador de comandos de DISKPART, escriba exit y pulse .
2 En la ventana Oracle Clusterware – Autorun (Software de clúster Oracle – Ejecución automática), haga clic en Install/Deinstall Products (Instalar/desinstalar productos). Se inicia Oracle Universal Installer (OUI) y se abre la ventana de bienvenida. 3 Haga clic en Next (Siguiente). 4 En la ventana Specify Home Details (Especificar detalles de la ubicación principal), acepte los valores predeterminados y haga clic en Next (Siguiente).
11 En la ventana Cluster Configuration Storage (Almacenamiento de configuración de clúster), realice los pasos siguientes para cada disco de votación: a Localice la partición de 50 MB creada en el procedimiento "Preparación de los discos OCR y de votación para el software de clúster". b Seleccione la partición y haga clic en Edit (Editar).
16 En la ventana Summary (Resumen), haga clic en Install (Instalar) para iniciar el procedimiento de instalación. Aparece la ventana de instalación, donde se muestra una barra de progreso de la instalación. A continuación, se abre la ventana Configuration Assistant (Asistente de configuración) y OUI ejecuta una serie de herramientas de configuración. Finalmente, aparece la ventana End of Installation (Fin de la instalación). NOTA: no haga clic con el botón derecho del ratón en el área de partición de disco.
Instalación de la base de datos Oracle 10g R2 con Real Application Clusters 10.2.1 1 En el nodo 1, inserte el CD Oracle Database 10g Release 2 for Microsoft Windows (Base de datos Oracle 10g versión 2 para Microsoft Windows) en la unidad de CD. Aparece la ventana Oracle Database 10g – Autorun (Base de datos Oracle 10g – Ejecución automática). Si esta ventana no aparece: a Haga clic en Inicio y seleccione Ejecutar.
9 En la ventana Select Configuration Option (Seleccionar opción de configuración), seleccione Install database Software only (Instalar sólo software de base de datos) y haga clic en Next (Siguiente). 10 En la ventana Summary (Resumen), haga clic en Install (Instalar). 11 En la ventana End of Installation (Fin de la instalación), realice el procedimiento tal como se indica en la ventana. NOTA: antes de ir al paso siguiente, debe realizar los procedimientos tal como se enumeran en la ventana.
4 En la ventana Specify Hardware Cluster Installation Mode (Especificar el modo de instalación del clúster de hardware), haga clic en Next (Siguiente). 5 En la ventana Summary (Resumen), haga clic en Install (Instalar). 6 En la ventana End of installation (Fin de la instalación), realice todos los pasos que se enumeran en la ventana Summary (Resumen), excepto el paso 1. 7 En la ventana End of Installation (Fin de la instalación), haga clic en Exit (Salir) y, a continuación, en Yes (Sí) para salir de OUI.
Instalación de los parches de Oracle más recientes 1 Abra un explorador web. 2 Vaya a la página web de Oracle Metalink (metalink.oracle.com). 3 Descargue los parches pertinentes para la instalación. Instalación del parche para "split brain" durante el inicio del sistema 1 Vaya a la carpeta etiquetada patch5059258. 2 Copie el archivo opmd.exe en el directorio %CRS_HOME%\bin en todos los nodos. 3 Escriba lo siguiente en el indicador de comandos: %SystemDrive%\%CRS_HOME%\bin> ompd.
9 En la ventana Listener Configuration, TCP/IP Protocol (Configuración del proceso de escucha, Protocolo TCP/IP), seleccione Use the standard port number of 1521 (Utilizar el puerto estándar 1521) y haga clic en Next (Siguiente). 10 En la ventana Listener Configuration, More Listeners (Configuración del proceso de escucha, ¿Más procesos de escucha?), seleccione No y haga clic en Next (Siguiente).
11 En la ventana Database File Locations (Ubicaciones de archivos de base de datos), seleccione la ubicación para almacenar los archivos de la base de datos: a Seleccione Use Common Location for All Database Files (Utilizar ubicación común para todos los archivos de base de datos). b Haga clic en Browse (Examinar).
21 En la ventana Creation Options (Opciones de creación), acepte los valores predeterminados y haga clic en Finish (Finalizar). 22 En la ventana Summary (Resumen), haga clic en OK (Aceptar). Aparece la ventana del asistente para la configuración de bases de datos, y el software Oracle crea la base de datos. NOTA: este procedimiento puede tardar varios minutos en completarse. 23 En la ventana del asistente para la configuración de bases de datos, haga clic en Yes (Sí).
2 En la ventana Oracle Clusterware (Software de clúster Oracle), haga clic en Install/Deinstall Products (Instalar/desinstalar productos). 3 En la pantalla de bienvenida, haga clic en Next (Siguiente). 4 En la ventana Specify Home Details (Especificar detalles de la ubicación principal), acepte los valores predeterminados y haga clic en Next (Siguiente). NOTA: anote la ruta OraCR10g_home (ubicación principal de CRS), ya que necesitará esta información más adelante.
11 En la pantalla Cluster Configuration Storage (Almacenamiento de configuración de clúster), realice los pasos siguientes para el disco de votación: a Localice la partición de 50 MB que creó en el apartado "Preparación de los discos OCR y de votación para el software de clúster". b Seleccione la partición y haga clic en Edit (Editar).
Instalación de la base de datos Oracle10g con Real Application Clusters 10.2.0.1 1 Inserte el CD Oracle Database 10g Release 2 en la unidad de CD. OUI se inicia y aparece la pantalla de bienvenida. Si la pantalla de bienvenida no aparece: a Haga clic en Inicio y seleccione Ejecutar. b En el campo Ejecutar, escriba: %Unidad_CD%\autorun\autorun.exe donde %Unidad_CD% es la letra de la unidad de CD. 2 Haga clic en Aceptar para continuar. OUI se inicia y aparece la ventana de bienvenida .
Instalación del patchset 10.2.0.2 NOTA: los pasos de instalación del patchset siguientes solamente instalan software Oracle como el sofware de clúster 10.2.0.1 y los binarios de base de datos 10.2.0.1 con la base de datos semilla que todavía no se crearon en su sistema. 1 Descargue el parche 10.2.0.2 de la página web Oracle Metalink en metalink.oracle.com. 2 Descomprima el patchset en la ubicación siguiente %SystemDrive%. donde %SystemDrive% es la unidad local del usuario. Instalación del patchset 10.2.0.
Pasos de instalación del patchset 1 Inicie el instalador OUI que se encuentra en la carpeta del patchset. 2 En la ventana de bienvenida, haga clic en Next (Siguiente). 3 En la ventana Specify home details (Especificar detalles de la ubicación principal), seleccione el nombre como OraDb10g_home1 en la lista desplegable para instalar el patchset en la ruta principal de Oracle y haga clic en Next (Siguiente).
Configuración del proceso de escucha En esta sección se describen los procedimientos necesarios para configurar el proceso de escucha, que es necesario para establecer una conexión remota de un cliente a una base de datos. Realice los pasos siguientes en el nodo 1: 1 Haga clic en Inicio, seleccione Ejecutar y escriba netca 2 Haga clic en OK (Aceptar).
Creación de la base de datos semilla Para crear la base de datos semilla mediante Oracle ASM, realice los pasos siguientes: 1 Compruebe que el software de clúster Oracle se esté ejecutando. a Abra una ventana de indicador de comandos. Haga clic en Inicio, seleccione Ejecutar, escriba cmd y pulse .
10 En la ventana Database Credentials (Credenciales de la base de datos), haga clic en Use the Same Password for All Accounts (Utilizar la misma contraseña para todas las cuentas), escriba y confirme una contraseña nueva en los campos pertinentes y haga clic en Next (Siguiente). NOTA: anote la contraseña nueva, ya que la necesitará posteriormente para la administración de la base de datos.
16 En la ventana ASM Disk Groups (Grupos de discos ASM), haga clic en Create New (Crear nuevo). 17 En la ventana Create Disk Group (Crear grupo de discos), introduzca la información para el área de recuperación flash. a En el campo Disk Group Name (Nombre de grupo de discos), introduzca un nombre para el grupo de discos nuevo. Por ejemplo, FLASH. b En la casilla Redundancy (Redundancia), seleccione External (Externa). c Haga clic en Stamp Disks (Marcar discos).
Haga clic en Edit Archive Mode Parameters (Editar parámetros del modo de archivo). f • g En la ventana Edit Archive Mode Parameters (Editar parámetros del modo archivo), asegúrese de que la ruta de acceso especifica en Archive Log Destinations (Archivar destinos de registro) es la siguiente: +FLASH/, donde FLASH es el nombre del grupo de discos de área de recuperación flash que especificó en el paso a del paso 17. Haga clic en Siguiente.
Tabla 1-8. Versiones de software admitidas (continuación) Componentes de software Versiones admitidas Controlador Storport HBA QLogic 9.1.2.15 Controlador Storport HBA Emulex 7-.1.11.3 Controladora RAID integrada PERC 5/i 1.18.0.64 PERC 4e/Di y PERC 4e/Si 6.46.3.64 Intel 1000 MT/XT (controlador base) 8.4.21.0 Familia de adaptadores Intel PRO PCIe Gigabit 9.4.24.1 Intel PROSet (para agrupación de NIC) 10.2.78.5 Broadcom BCM95701, BCM95703, BCM95703s y Gigabit 5700 (controlador base) 8.48.
El asistente para la configuración de IP privada virtual falla Si el VIPCA falla durante la instalación del software de clúster de Oracle, puede aparecer el mensaje siguiente: Virtual Private IP Configuration Assistant failed (El asistente para la configuración de IP privada virtual ha fallado) En este caso, realice los pasos que se describen a continuación para solucionar el error. Estos pasos se detallan en la nota 338924.1 de Metalink.
Eliminación de los servicios de Oracle 1 En el nodo 1, inicie la consola de servicios. a Haga clic en Inicio y seleccione Ejecutar. b En el campo Ejecutar, escriba lo siguiente y haga clic en Aceptar: services.msc Aparece la ventana Services (Servicios). 2 Identifique y elimine todos los servicios de Oracle que queden. Para eliminar un servicio: a Haga clic en Inicio y seleccione Ejecutar. b En el campo Ejecutar, escriba cmd y haga clic en Aceptar.
2 Asegúrese de que OCRCFG y VOTEDSK aparecen en el archivo. Si OCRCFG y VOTEDSK no aparecen en el archivo, asígnelos al disco apropiado y guarde al archivo. Utilice el importador de enlaces dinámicos de Oracle (ImportSYMLinks) para importar los enlaces simbólicos en los discos de almacenamiento asignados (OCRCFG y VOTEDSK). En el indicador de comandos, escriba lo siguiente y pulse : %SystemDrive%\oracle\product\10.2.0\crs\bin\ImportSYMLinks donde %SystemDrive% es la unidad local del usuario.
7 Inicie la consola de administración de equipos. a En el escritorio de Windows, haga clic en Inicio y seleccione Ejecutar. b En el campo Ejecutar, escriba lo siguiente y pulse : compmgmt.msc Aparece la ventana de la consola de administración de equipos. 8 Elimine las particiones ASM u OCFS. a En la ventana de la consola de administración de equipos, haga clic en Almacenamiento y seleccione Administración de discos.
Solución de problemas adicionales En la tabla 1-9 se indican las acciones recomendadas para los problemas que pueden surgir al implantar y utilizar el sistema operativo Windows Server 2003 y el software de base de datos Oracle 10g R2. Tabla 1-9. Solución de problemas Categoría Problema / síntoma Causa Agrupación La agrupación de Los pasos siguientes pueden provocar de NIC NIC Broadcom un error en una agrupación de NIC: falla.
Tabla 1-9. Categoría Solución de problemas (continuación) Problema / síntoma Causa Software de El nodo del El nodo del clúster no puede clúster clúster se reinicia comunicarse con los discos de Oracle con una pantalla almacenamiento. azul. Acción correctiva recomendada Realice los pasos siguientes: 1 Reinicie el nodo del clúster. 2 Durante la POST, pulse . 3 En la pantalla Menú de opciones avanzadas de Windows, seleccione Modo seguro. 4 Seleccione el sistema operativo adecuado.
Tabla 1-9. Solución de problemas (continuación) Categoría Problema / síntoma Causa Pantalla azul del sistema Los nodos del Los nodos del clúster no pueden clúster generan acceder al disco de votación. una pantalla azul. Acción correctiva recomendada 1 Asegúrese de que los valores del firmware para el modo de conexión de HBA estén configurados correctamente para su configuración de almacenamiento.
Tabla 1-9. Categoría Solución de problemas (continuación) Problema / síntoma En No se puede almacenam acceder a los iento discos. Causa Acción correctiva recomendada En el escritorio de Windows, cuando hace clic con el botón derecho del ratón en Mi PC, selecciona Administración de equipos y hace clic en Administración de discos, los discos aparecen como inaccesibles. Compruebe que se hayan asignado LUN de almacenamiento a los dos nodos del clúster.
Tabla 1-9. Solución de problemas (continuación) Categoría Problema / síntoma Causa Acción correctiva recomendada VIPCA La configuración de VIPCA falla. El nombre de la interfaz de adaptador de red pública (o la interfaz de red asignada para VIP, en el caso de cuatro interfaces de red) no es el mismo en los dos nodos del clúster. Asegúrese de que el nombre de la interfaz de adaptador de red pública es el mismo en los dos nodos del clúster.
Obtención y uso de archivos fuente abiertos El software que se incluye en el CD de implantación es un complemento de programas de terceros, así como programas de Dell. El uso del software está sujeto a las condiciones específicas de la licencia. Todo el software designado bajo las condiciones de la GPL de GNU se puede copiar, distribuir o modificar según las condiciones de la Licencia pública general GNU, versión 2, junio de 1991.
Guía de implantación
Índice B E O bonding, 290 ejemplos conexiones de hardware para un clúster Fibre Channel, 286 obtener ayuda, 330 C clúster ejemplo de conexiones de hardware Fibre Channel, 286 configuración del clúster Fibre Channel, 285 configuraciones de hardware y software Fibre Channel, 287 configurar la red privada, 290 configurar las redes pública y privada, 289 configurar Oracle 10g, 285 verificar las configuraciones de hardware y software, 285 contratos de licencia, 283 F Fibre Channel, configuración del clúst
Índice 334 Índice