Dell Configuration Guide for the S4048–ON System 9.14.2.5 January 2020 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 - 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: About this Guide.........................................................................................................33 Audience.............................................................................................................................................................................. 33 Conventions........................................................................................................................................................................
Removing a Command from EXEC Mode............................................................................................................. 59 Moving a Command from EXEC Privilege Mode to EXEC Mode.................................................................... 59 Allowing Access to CONFIGURATION Mode Commands................................................................................. 59 Allowing Access to Different Modes...........................................................................
Enabling 802.1X................................................................................................................................................................. 89 Configuring dot1x Profile ................................................................................................................................................90 Configuring MAC addresses for a do1x Profile..........................................................................................................
Configure Ingress ACLs.................................................................................................................................................. 121 Configure Egress ACLs.................................................................................................................................................. 122 Applying Egress Layer 3 ACLs (Control-Plane)..................................................................................................122 IP Prefix Lists......
BGP global and address family configuration..................................................................................................... 180 Implement BGP with Dell EMC Networking OS.................................................................................................. 181 Configuration Information........................................................................................................................................184 Basic BGP configuration tasks.........................
Configuring CAM Threshold and Silence Period...................................................................................................... 241 CAM Optimization...........................................................................................................................................................242 Troubleshoot CAM Profiling.........................................................................................................................................
Configuring DCBx......................................................................................................................................................275 Verifying the DCB Configuration.................................................................................................................................279 QoS dot1p Traffic Classification and Queue Assignment......................................................................................
Configuring the Hash Algorithm Seed.................................................................................................................. 318 Link Bundle Monitoring...................................................................................................................................................318 Managing ECMP Group Paths................................................................................................................................
Important FRRP Concepts...................................................................................................................................... 351 Implementing FRRP.........................................................................................................................................................351 FRRP Configuration.......................................................................................................................................................
Enabling IGMP Immediate-Leave................................................................................................................................ 377 IGMP Snooping................................................................................................................................................................378 Configuring IGMP Snooping...................................................................................................................................
Load Balancing Through Port Channels.............................................................................................................. 408 Changing the Hash Algorithm................................................................................................................................ 408 Bulk Configuration.......................................................................................................................................................... 409 Interface Range.........
Specifying the Local System Domain and a List of Domains................................................................................ 441 Configuring DNS with Traceroute............................................................................................................................... 441 ARP.....................................................................................................................................................................................
Showing IPv6 Routes............................................................................................................................................... 464 Showing the Running-Configuration for an Interface......................................................................................465 Clearing IPv6 Routes................................................................................................................................................465 Disabling ND Entry Timeout...........
Introduction to Dynamic LAGs and LACP.................................................................................................................499 Important Points to Remember............................................................................................................................. 499 LACP Modes.............................................................................................................................................................. 500 Configuring LACP Commands..
Enabling LLDP..................................................................................................................................................................534 Disabling and Undoing LLDP.................................................................................................................................. 534 Enabling LLDP on Management Ports.......................................................................................................................
MLD timers....................................................................................................................................................................... 577 Reducing Host Response Burstiness.................................................................................................................... 577 Configuring MLD Version..............................................................................................................................................
Enable MLD Snooping...............................................................................................................................................614 Disable MLD Snooping..............................................................................................................................................614 Configure the switch as a querier..........................................................................................................................
Configuring Passive-Interface............................................................................................................................... 663 Redistributing Routes...............................................................................................................................................664 Configuring a Default Route...................................................................................................................................
Displaying Remote-Port Mirroring Configurations............................................................................................ 706 Configuration procedure for Remote Port Mirroring........................................................................................707 Encapsulated Remote Port Monitoring....................................................................................................................... 711 ERPM Behavior on a typical Dell EMC Networking OS ..................
Creating WRED Profiles........................................................................................................................................... 751 Applying a WRED Profile to Traffic....................................................................................................................... 751 Displaying Default and Configured WRED Profiles............................................................................................ 751 Displaying WRED Drop Statistics.............
Influencing RSTP Root Selection................................................................................................................................ 787 Configuring an EdgePort............................................................................................................................................... 787 Configuring Fast Hellos for Link State Detection...................................................................................................
Handling Access-Challenge Message................................................................................................................... 841 Configuring Challenge Response Authentication for SSHv2.......................................................................... 841 SMS-OTP Mechanism............................................................................................................................................. 842 Configuring the System to Drop Certain ICMP Reply Messages....
Chapter 53: Simple Network Management Protocol (SNMP)..................................................... 872 Protocol Overview.......................................................................................................................................................... 873 Implementation Information..........................................................................................................................................873 SNMPv3 Compliance With FIPS..............................
MIB objects for configuring MAC addresses...................................................................................................... 901 MIB objects for configuring MAC addresses..................................................................................................... 902 Manage VLANs using SNMP........................................................................................................................................902 Creating a VLAN.......................................
Recover from a Card Problem State on a Stack...............................................................................................935 Chapter 55: Storm Control........................................................................................................ 936 Configure Storm Control...............................................................................................................................................936 Configuring Storm Control from INTERFACE Mode....................
Dell EMC Networking OS Time and Date................................................................................................................. 966 Configuration Task List .......................................................................................................................................... 966 Setting the Time and Date for the Switch Software Clock........................................................................... 966 Setting the Timezone....................................
Primary and Secondary VLT Peers....................................................................................................................... 999 RSTP and VLT........................................................................................................................................................... 999 VLT Bandwidth Monitoring................................................................................................................................... 1000 VLT and Stacking........
Chapter 65: Virtual Extensible LAN (VXLAN)........................................................................... 1065 Components of VXLAN network............................................................................................................................... 1066 Functional Overview of VXLAN Gateway............................................................................................................... 1067 VXLAN Frame Format..........................................................
Chapter 67: Virtual Router Redundancy Protocol (VRRP)......................................................... 1108 VRRP Overview..............................................................................................................................................................1108 VRRP Benefits................................................................................................................................................................ 1109 VRRP Implementation......................
Chapter 70: X.509v3.................................................................................................................1166 Introduction to X.509v3 certificates.........................................................................................................................1166 X.509v3 support in .......................................................................................................................................................
1 About this Guide This guide describes the protocols and features the Dell EMC Networking Operating System (OS) supports and provides configuration instructions and examples for implementing them. For complete information about all the CLI commands, see the Dell EMC Command Line Reference Guide for your system. The S4048–ON platform is available with Dell EMC Networking OS version 9.7.(0.1) and beyond.S4048–ON stacking is supported with Dell EMC Networking OS version 9.7(0.1) and beyond.
2 Configuration Fundamentals The Dell EMC Networking Operating System (OS) command line interface (CLI) is a text-based interface you can use to configure interfaces and protocols. The CLI is largely the same for each platform except for some commands and command outputs. The CLI is structured in modes for security and management purposes. Different sets of commands are available in each mode, and you can limit user access to modes using privilege levels.
The Dell EMC Networking OS CLI is divided into three major mode levels: ● EXEC mode is the default mode and has a privilege level of 1, which is the most restricted level. Only a limited selection of commands is available, notably the show commands, which allow you to view system information. ● EXEC Privilege mode has commands to view configurations, clear counters, manage configuration files, run diagnostics, and enable or disable debug operations. The privilege level is 15, which is unrestricted.
RSTP ROUTE-MAP ROUTER BGP BGP ADDRESS-FAMILY ROUTER ISIS ISIS ADDRESS-FAMILY ROUTER OSPF ROUTER OSPFV3 ROUTER RIP SPANNING TREE SUPPORTASSIST TRACE-LIST VLT DOMAIN VRRP UPLINK STATE GROUP uBoot Navigating CLI Modes The Dell EMC Networking OS prompt changes to indicate the CLI mode. The following table lists the CLI mode, its prompt, and information about how to access and exit the CLI mode.
Table 1.
Table 1.
The do Command You can enter an EXEC mode command from any CONFIGURATION mode (CONFIGURATION, INTERFACE, SPANNING TREE, and so on.) without having to return to EXEC mode by preceding the EXEC mode command with the do command. The following example shows the output of the do command.
Obtaining Help Obtain a list of keywords and a brief functional description of those keywords at any CLI mode using the ? or help command: ● To list the keywords available in the current mode, enter ? at the prompt or after a keyword. ● Enter ? after a command prompt to list all of the available keywords. The output of this command is the same as the help command.
Short-Cut Key Action Combination CNTL-R Re-enters the previous command. CNTL-U Deletes the line. CNTL-W Deletes the previous word. CNTL-X Deletes the line. CNTL-Z Ends continuous scrolling of command outputs. Esc B Moves the cursor back one word. Esc F Moves the cursor forward one word. Esc D Deletes all characters from the cursor to the end of the word. Command History The Dell EMC Networking OS maintains a history of previously-entered commands for each mode.
Reload-Type : normal-reload [Next boot : normal-reload] The find keyword displays the output of the show command beginning from the first occurrence of specified text. The following example shows this command used in combination with the show system brief command. Example of the find Keyword The display command displays additional configuration information. The no-more command displays the output all at once rather than one screen at a time.
3 Getting Started This chapter describes how you start configuring your system. When you power up the chassis, the system performs a power-on self test (POST) and system then loads the Dell EMC Networking Operating System. Boot messages scroll up the terminal window during this process. No user interaction is required if the boot process proceeds without interruption. When the boot process completes, the system status LEDs remain online (green) and the console monitor displays the EXEC mode prompt.
Accessing the Console Port To access the console port, follow these steps: For the console port pinout, refer to Accessing the RJ-45 Console Port with a DB-9 Adapter. 1. Install an RJ-45 copper cable into the console port. Use a rollover (crossover) cable to connect the console port to a terminal server. 2. Connect the other end of the cable to the DTE terminal server. 3.
The SSH server transmits the terminal commands to the CLI shell and the results are displayed on the screen non-interactively. Executing Local CLI Scripts Using an SSH Connection You can execute CLI commands by entering a CLI script in one of the following ways: ssh username@hostname or cat < CLIscript.file > | ssh admin@hostname The script is run and the actions contained in the script are performed.
Accessing the System Remotely Configuring the system for remote access is a three-step process, as described in the following topics: 1. Configure an IP address for the management port. Configure the Management Port IP Address 2. Configure a management route with a default gateway. Configure a Management Route 3. Configure a username and password. Configure a Username and Password Configure the Management Port IP Address To access the system remotely, assign IP addresses to the management ports. 1.
○ sha256–password: Uses sha256–based encryption method for password. ○ encryption-type: Enter the encryption type for securing an user password. There are four encryption types. ￭ 0 — input the password in clear text. ￭ 5 — input the password that is already encrypted using MD5 encryption method. ￭ 7 — input the password that is already encrypted using DES encryption method. ￭ 8 — input the password that is already encrypted using sha256–based encryption method.
Configuration File Management Files can be stored on and accessed from various storage media. Rename, delete, and copy files on the system from EXEC Privilege mode. Copy Files to and from the System The command syntax for copying files is similar to UNIX. The copy command uses the format copy source-file-url destination-file-url. NOTE: For a detailed description of the copy command, refer to the Dell EMC Networking OS Command Reference.
Before executing any CLI command to perform file operations, you must first mount the NFS file system to a mount-point on the device. Since multiple mount-points exist on a device, it is mandatory to specify the mount-point to which you want to load the system. The /f10/mnt/nfs directory is the root of all mount-points. To mount an NFS file system, perform the following steps: Table 4.
! 24 bytes successfully copied DellEMC# DellEMC#copy tftp://10.16.127.35/username/dv-maa-test ? flash: Copy to local file system ([flash://]filepath) nfsmount: Copy to nfs mount file system (nfsmount:///filepath) running-config remote host: Destination file name [test.c]: ! 225 bytes successfully copied DellEMC# Save the Running-Configuration The running-configuration contains the current system configuration. Dell EMC Networking recommends coping your runningconfiguration to the startup-configuration.
EXEC Privilege mode show startup-config The output of the dir command also shows the read/write privileges, size (in bytes), and date of modification for each file.
Table 6.
Table 6. Standard and Compressed Configurations (continued) Uncompressed Compressed ! interface Vlan 5 tagged te 1/1 no ip address shutdown ! interface Vlan 100 no ip address no shutdown ! interface Vlan 1000 ip address 1.1.1.1/16 no shutdown Uncompressed config size – 52 lines write memory compressed The write memory compressed CLI will write the operating configuration to the startup-config file in the compressed mode.
You can change the default file system so that file management commands apply to a particular device or memory. To change the default directory, use the following command. ● Change the default directory. EXEC Privilege mode cd directory Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.
Example of the show command-history Command Example 1: Default configuration service timestamps log datetime or service timestamps log datetime localtime DellEMC(conf)#service timestamps log datetime DellEMC# show command-history - Repeated 1 time. [May 17 15:38:55]: CMD-(CLI):[service timestamps log datetime]by default from console [May 17 15:41:40]: CMD-(CLI):[write memory]by default from console - Repeated 1 time.
[May 17 15:53:16]: CMD-(CLI):[write memory]by default from console - Repeated 3 times. [May 17 15:53:22]: CMD-(CLI):[show logging]by default from console - Repeated 1 time. [May 17 15:53:36]: CMD-(CLI):[write memory]by default from console - Repeated 5 times.
MD5 DellEMC# verify md5 flash:file-name SHA256 DellEMC# verify sha256 flash://file-name Examples: Entering the Hash Value for Verification MD5 DellEMC# verify md5 flash://file-name 275ceb73a4f3118e1d6bcf7d75753459 SHA256 DellEMC# verify sha256 flash://file-name e6328c06faf814e6899ceead219afbf9360e986d692988023b749e6b2093e933 Using HTTP for File Transfers Stating with Release 9.3(0.1), you can use HTTP to copy files or configuration details to a remote server.
4 Management This chapter describes the different protocols or services used to manage the Dell EMC Networking system.
Removing a Command from EXEC Mode To remove a command from the list of available commands in EXEC mode for a specific privilege level, use the privilege exec command from CONFIGURATION mode. In the command, specify a level greater than the level given to a user or terminal line, then the first keyword of each command you wish to restrict.
privilege configure level level {interface | line | route-map | router} {command-keyword ||...|| command-keyword} ● Allow access to a CONFIGURATION, INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode command. CONFIGURATION mode privilege {configure |interface | line | route-map | router} level level {command ||...
DellEMC(conf)# interface group vlan 1 - 2 , tengigabitethernet 1/1 DellEMC(conf-if-group-vl-1-2,te-1/1)# no shutdown DellEMC(conf-if-group-vl-1-2,te-1/1)# end Applying a Privilege Level to a Username To set the user privilege level, use the following command. ● Configure a privilege level for a user. CONFIGURATION mode username username privilege level Applying a Privilege Level to a Terminal Line To set a privilege level for a terminal line, use the following command.
● Clearing Audit Logs Enabling Audit and Security Logs You enable audit and security logs to monitor configuration changes or determine if these changes affect the operation of the system in the network. You log audit and security events to a system log server, using the logging extended command in CONFIGURATION mode. This command is available with or without RBAC enabled. For information about RBAC, see Role-Based Access Control. Audit Logs The audit log contains configuration events and information.
Example of the show logging auditlog Command DellEMC#show logging auditlog May 12 12:20:25: DellEMC#: %CLI-6-logging extended by admin from vty0 (10.14.1.98) May 12 12:20:42: DellEMC#: %CLI-6-configure terminal by admin from vty0 (10.14.1.98) May 12 12:20:42: DellEMC#: %CLI-6-service timestamps log datetime by admin from vty0 (10.14.1.
%CHMGR-5-CARDDETECTED: Line card 8 present %CHMGR-5-CARDDETECTED: Line card 10 present %CHMGR-5-CARDDETECTED: Line card 12 present %TSM-6-SFM_DISCOVERY: Found SFM 0 %TSM-6-SFM_DISCOVERY: Found SFM 1 %TSM-6-SFM_DISCOVERY: Found SFM 2 %TSM-6-SFM_DISCOVERY: Found SFM 3 %TSM-6-SFM_DISCOVERY: Found SFM 4 %TSM-6-SFM_DISCOVERY: Found SFM 5 %TSM-6-SFM_DISCOVERY: Found SFM 6 %TSM-6-SFM_DISCOVERY: Found SFM 7 %TSM-6-SFM_SWITCHFAB_STATE: Switch Fabric: UP %TSM-6-SFM_DISCOVERY: Found SFM 8 %TSM-6-SFM_DISCOVERY: Found 9
Pre-requisites To configure a secure connection from the switch to the syslog server: 1. On the switch, enable the SSH server DellEMC(conf)#ip ssh server enable 2. On the syslog server, create a reverse SSH tunnel from the syslog server to the Dell OS switch, using following syntax: ssh -R :: user@remote_host -nNf In the following example the syslog server IP address is 10.156.166.48 and the listening port is 5141. The switch IP address is 10.16.131.
Configuring Login Activity Tracking To enable and configure login activity tracking, follow these steps: 1. Enable login activity tracking. CONFIGURATION mode login statistics enable After enabling login statistics, the system stores the login activity details for the last 30 days. 2. (Optional) Configure the number of days for which the system stores the user login statistics. The range is from 1 to 30.
-----------------------------------------------------------------User: admin2 Last login time: 12:49:27 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
Restrictions for Limiting the Number of Concurrent Sessions These restrictions apply for limiting the number of concurrent sessions: ● Only the system and security administrators can limit the number of concurrent sessions and enable the clear-line option. ● Users can clear their existing sessions only if the system is configured with the login concurrent-session clearline enable command.
When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of the existing sessions. If you close any of the existing sessions, you are allowed to login. $ telnet 10.11.178.17 Trying 10.11.178.17... Connected to 10.11.178.17. Escape character is '^]'. Login: admin Password: Maximum concurrent sessions for the user reached. Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.97 4 vty 2 10.14.1.97 5 vty 3 10.14.1.
CONFIGURATION mode no logging monitor ● Disable console logging. CONFIGURATION mode no logging console Sending System Messages to a Syslog Server To send system messages to a specified syslog server, use the following command. The following syslog standards are supported: RFC 5424 The SYSLOG Protocol, R.Gerhards and Adiscon GmbH, March 2009, obsoletes RFC 3164 and RFC 5426 Transmission of Syslog Messages over UDP. ● Specify the server to which you want to send system messages.
CONFIGURATION mode logging buffered size NOTE: When you decrease the buffer size, Dell EMC Networking OS deletes all messages stored in the buffer. Increasing the buffer size does not affect messages in the buffer. ● Specify the number of messages that Dell EMC Networking OS saves to its logging history table.
Configuring a UNIX Logging Facility Level You can save system log messages with a UNIX system logging facility. To configure a UNIX logging facility level, use the following command. ● Specify one of the following parameters.
line {console 0 | vty number [end-number] | aux 0} Configure the following parameters for the virtual terminal lines: ● number: the range is from zero (0) to 8. ● end-number: the range is from 1 to 8. You can configure multiple virtual terminals at one time by entering a number and an end-number. 2. Configure a level and set the maximum number of messages to print.
[May 17 15:43:22]: CMD-(CLI):[show command-history]by default from console DellEMC# DellEMC#show logging Syslog logging: enabled Console logging: disabled Monitor logging: level debugging Buffer logging: level debugging, 7 Messages Logged, Size (40960 bytes) Trap logging: level informational Last logging buffer cleared: May 17 15:38:38 May 17 15:43:08 %STKUNIT1-M:CP %SYS-5-CONFIG_I: Configured from console May 17 15:42:52 %STKUNIT1-M:CP %FILEMGR-5-FILESAVED: Copied running-config config in flash by default
DellEMC(conf)#service timestamps log uptime DellEMC#show clock 15:51:47.
%STKUNIT1-M:CP %FILEMGR-5-FILESAVED: Copied running-config to startup-config in flash by default - repeated 3 times %STKUNIT1-M:CP %FILEMGR-5-FILESAVED: Copied running-config to startup-config in flash by default File Transfer Services With Dell EMC Networking OS, you can configure the system to transfer files over the network using the file transfer protocol (FTP).
ftp-server username username password [encryption-type] password Configure the following optional and required parameters: ○ username: enter a text string. ○ encryption-type: enter 0 for plain text or 7 for encrypted text. ○ password: enter a text string. NOTE: You cannot use the change directory (cd) command until you have configured ftp-server topdir. To view the FTP configuration, use the show running-config ftp command in EXEC privilege mode.
processes either IPv4 or IPv6 rules, but not both. Using this configuration, you can set up two different types of access classes with each class processing either IPv4 or IPv6 rules separately. To apply an IP ACL to a line, Use the following command. ● Apply an ACL to a VTY line. LINE mode access-class access-list-name [ipv4 | ipv6] NOTE: If you already have configured generic IP ACL on a terminal line, then you cannot further apply IPv4 or IPv6 specific filtering on top of this configuration.
radius Prompt for a username and password and use a RADIUS server to authenticate. tacacs+ Prompt for a username and password and use a TACACS+ server to authenticate. 1. Configure an authentication method list. You may use a mnemonic name or use the keyword default. The default authentication method for terminal lines is local and the default method list is empty.
Using Telnet to get to Another Network Device To telnet to another device, use the following commands. NOTE: The device allows 120 Telnet sessions per minute, allowing the login and logout of 10 Telnet sessions, 12 times in a minute. If the system reaches this non-practical limit, the Telnet service is stopped for 10 minutes. You can use console and SSH service to access the system during downtime. ● Telnet to a device with an IPv4 or IPv6 address.
If another user attempts to enter CONFIGURATION mode while a lock is in place, the following appears on their terminal (message 1): % Error: User "" on line console0 is in exclusive configuration mode. If any user is already in CONFIGURATION mode when while a lock is in place, the following appears on their terminal (message 2): % Error: Can't lock configuration mode exclusively since the following users are currently configuring the system: User "admin" on line vty1 ( 10.1.1.1 ).
Restoring the Factory Default Settings Restoring the factory-default settings deletes the existing NVRAM settings, startup configuration, and all configured settings such as, stacking or fanout. To restore the factory default settings, use the restore factory-defaults stack-unit {stack—unit—number | all} {clear-all | nvram | bootvar} command in EXEC Privilege mode. CAUTION: There is no undo for this command.
Important Points to Remember ● The Chassis remains in boot prompt if none of the partitions contain valid images. ● To enable TFTP boot after restoring factory default settings, you must stop the boot process in BLI. In case the system fails to reload the image from the partition, perform the following steps: 1. Power-cycle the chassis (pull the power cord and reinsert it). 2. Hit any key to abort the boot process. You enter uBoot immediately, the => prompt indicates success.
Enter the stack-unit keyword and the keyword all to view the reason for the last system reboot of all stack units in the stack.
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. A device connected to a port that is enabled with 802.1X is disallowed from sending or receiving packets on the network until its identity is verified (through a username and password, for example). 802.
● The device attempting to access the network is the supplicant. The supplicant is not allowed to communicate on the network until the authenticator authorizes the port. It can only communicate with the authenticator in response to 802.1X requests. ● The device with which the supplicant communicates is the authenticator. The authenticator is the gate keeper of the network. It translates and forwards requests and responses between the authentication server and the supplicant.
Figure 5. EAP Port-Authentication EAP over RADIUS 802.1X uses RADIUS to shuttle EAP packets between the authenticator and the authentication server, as defined in RFC 3579. EAP messages are encapsulated in RADIUS packets as a type of attribute in Type, Length, Value (TLV) format. The Type value for EAP messages is 79. Figure 6. EAP Over RADIUS RADIUS Attributes for 802.1X Support Dell EMC Networking systems include the following RADIUS attributes in all 802.
Configuring 802.1X Configuring 802.1X on a port is a one-step process. For more information, refer to Enabling 802.1X. Related Configuration Tasks ● ● ● ● ● ● Configuring Request Identity Re-Transmissions Forcibly Authorizing or Unauthorizing a Port Re-Authenticating a Port Configuring Timeouts Configuring a Guest VLAN Configuring an Authentication-Fail VLAN Important Points to Remember ● Dell EMC Networking OS supports 802.
Enabling 802.1X Enable 802.1X globally. Figure 7. 802.1X Enabled 1. Enable 802.1X globally. CONFIGURATION mode dot1x authentication 2. Enter INTERFACE mode on an interface or a range of interfaces. INTERFACE mode interface [range] 3. Enable 802.1X on the supplicant interface only. INTERFACE mode dot1x authentication Verify that 802.1X is enabled globally and at the interface level using the show running-config | find dot1x command from EXEC Privilege mode.
no ip address dot1x authentication no shutdown ! DellEMC# To view 802.1X configuration information for an interface, use the show dot1x interface command. In the following example, the bold lines show that 802.1X is enabled on all ports unauthorized by default. DellEMC#show dot1x interface TenGigabitEthernet 2/1/ 802.
● Configure a list of MAC addresses for a dot1x profile. DOT1X PROFILE CONFIG (conf-dot1x-profile) mac mac-address mac-address — Enter the keyword mac and type up to the 48– bit MAC addresses using the nn:nn:nn:nn:nn:nn format. A maximum of 6 MAC addresses are allowed. The following example configures 2 MAC addresses and then displays these addresses.
Auth PAE State: Backend State: Authenticated Idle Configuring Critical VLAN By default, critical-VLAN is not configured. If authentication fails because of a server which is not reachable, user session is authenticated under critical-VLAN. To configure a critical-VLAN for users or devices when authenticating server is not reachable, use the following command.
INTERFACE mode dot1x tx-period number The range is from 1 to 65535 (1 year) The default is 30. ● Configure the maximum number of times the authenticator re-transmits a Request Identity frame. INTERFACE mode dot1x max-eap-req number The range is from 1 to 10. The default is 2. The example in Configuring a Quiet Period after a Failed Authentication shows configuration information for a port for which the authenticator re-transmits an EAP Request Identity frame after 90 seconds and re-transmits for 10 times.
Forcibly Authorizing or Unauthorizing a Port The 802.1X ports can be placed into any of the three states: ● ForceAuthorized — an authorized state. A device connected to this port in this state is never subjected to the authentication process, but is allowed to communicate on the network. Placing the port in this state is same as disabling 802.1X on the port. ● ForceUnauthorized — an unauthorized state.
INTERFACE mode dot1x reauth-max number The range is from 1 to 10. The default is 2. The bold lines show that re-authentication is enabled and the new maximum and re-authentication time period. DellEMC(conf-if-Te-1/1)#dot1x reauthentication interval 7200 DellEMC(conf-if-Te-1/1)#dot1x reauth-max 10 DellEMC(conf-if-Te-1/1)#do show dot1x interface TenGigabitEthernet 1/1 802.
Guest VLAN: Disable Guest VLAN id: NONE Auth-Fail VLAN: Disable Auth-Fail VLAN id: NONE Auth-Fail Max-Attempts: NONE Tx Period: 90 seconds Quiet Period: 120 seconds ReAuth Max: 10 Supplicant Timeout: 15 seconds Server Timeout: 15 seconds Re-Auth Interval: 7200 seconds Max-EAP-Req: 10 Auth Type: Auth PAE State: Backend State: SINGLE_HOST Initialize Initialize Enter the tasks the user should do after finishing this task (optional).
Figure 8. Dynamic VLAN Assignment 1. Configure 8021.x globally (refer to Enabling 802.1X) along with relevant RADIUS server configurations (refer to the illustration inDynamic VLAN Assignment with Port Authentication). 2. Make the interface a switchport so that it can be assigned to a VLAN. 3. Create the VLAN to which the interface will be assigned. 4. Connect the supplicant to the port configured for 802.1X. 5.
● If a port is already forwarding on the Guest VLAN when 802.1X is enabled, the port is moved out of the Guest VLAN and the authentication process begins. Configuring a Guest VLAN If the supplicant does not respond within a determined amount of time ([reauth-max + 1] * tx-period, the system assumes that the host does not have 802.1X capability and the port is placed in the Guest VLAN. NOTE: For more information about configuring timeouts, refer to Configuring Timeouts.
Example of Viewing Configured Authentication 802.
6 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements.
The ACL manager does not notify the ACL agent in the following cases: ● The ACL VLAN group is created. ● The ACL VLAN group is deleted and it does not contain VLAN members. ● The ACL is applied or removed from a group and the ACL group does not contain a VLAN member. ● The description of the ACL group is added or removed.
acl-vlan-group {group name} 2. Add a description to the ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode description description 3. Add VLAN member(s) to an ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode member vlan {VLAN-range} 4. Display all the ACL VLAN groups or display a specific ACL VLAN group, identified by name.
Viewing CAM Usage View the amount of CAM space available, used, and remaining in each partition (including IPv4Flow and Layer 2 ACL subpartitions) using the show cam-usage command in EXEC Privilege mode. Display Layer 2, Layer 3, ACL, or all CAM usage statistics.
The following output displays CAM space usage for Layer 2 ACLs: DellEMC#show cam-usage switch Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|=================|=============|=============|============== 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 2 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 3 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 | | IN-L3 ECMP GRP | 1024 | 0 | 1024 Codes: * - cam usage is above
provides a reasonable shared memory for all the tables. The other supported UFT modes are scaled-l3–hosts (UFT mode 3) and scaled-l3–routes (UFT mode 4). Configuring UFT Modes To configure the Unified Forwarding Table (UFT) modes, follow these steps. 1. Select a mode to initialize the maximum scalability size for L2 MAC table or L3 Host table or L3 Route table.
7 Access Control Lists (ACLs) This chapter describes access control lists (ACLs), prefix lists, and route-maps. At their simplest, access control lists (ACLs), prefix lists, and route-maps permit or deny traffic based on MAC and/or IP addresses. This chapter describes implementing IP ACLs, IP prefix lists and route-maps. For MAC ACLS, refer to Layer 2.
• • • • • • • • • • • Applying an IP ACL Configure Ingress ACLs Configure Egress ACLs IP Prefix Lists ACL Remarks ACL Resequencing Route Maps Logging of ACL Processes Flow-Based Monitoring Configuring UDF ACL Configuring IP Mirror Access Group IP Access Control Lists (ACLs) In Dell EMC Networking switch/routers, you can create two different types of IP ACLs: standard or extended. A ● ● ● ● ● ● ● standard ACL filters packets based on the source IP packet.
Save the new CAM settings to the startup-config (use write-mem or copy run start) then reload the system for the new settings to take effect. CAM Optimization When you enable this command, if a policy map containing classification rules (ACL and/or dscp/ ip-precedence rules) is applied to more than one physical interface on the same port-pipe, only a single copy of the policy is written (only one FP entry is used). When you disable this command, the system behaves as described in this chapter.
You can use the log keyword to log the details about the packets that match. The control processor becomes busy based on the number of packets that match the log entry and the rate at which the details are logged in. However, the route processor (RP) is unaffected. You can use this option for debugging issues related to control traffic. ACL Optimization If an access list contains duplicate entries, Dell EMC Networking OS deletes one entry to conserve CAM space.
Configuration Task List for Route Maps Configure route maps in ROUTE-MAP mode and apply the maps in various commands in ROUTER RIP and ROUTER OSPF modes. The following list includes the configuration tasks for route maps, as described in the following sections.
level stub-area DellEMC# The following example shows a route map with multiple instances. The show config command displays only the configuration of the current route map instance. To view all instances of a specific route map, use the show route-map command.
Configuring Match Routes To configure match criterion for a route map, use the following commands. ● Match routes with the same AS-PATH numbers. CONFIG-ROUTE-MAP mode match as-path as-path-name ● Match routes with COMMUNITY list attributes in their path. CONFIG-ROUTE-MAP mode match community community-list-name [exact] ● Match routes whose next hop is a specific interface.
To create route map instances, use these commands. There is no limit to the number of match commands per route map, but the convention is to keep the number of match filters in a route map low. Set commands do not require a corresponding match command. Configuring Set Conditions To configure a set condition, use the following commands. ● Add an AS-PATH number to the beginning of the AS-PATH. CONFIG-ROUTE-MAP mode set as-path prepend as-number [...
a routing protocol. Other attributes that can be changed include the metric type (for example, external and internal route types in OSPF) and route tag. Use the redistribute command in OSPF, RIP, ISIS, and BGP to set some of these attributes for routes that are redistributed into those protocols. Route maps add to that redistribution capability by allowing you to match specific routes and set or change more attributes when redistributing those routes.
IP Fragment Handling Dell EMC Networking OS supports a configurable option to explicitly deny IP fragmented packets, particularly second and subsequent packets. It extends the existing ACL command syntax with the fragments keyword for all Layer 3 rules applicable to all Layer protocols (permit/deny ip/tcp/udp/icmp). ● Both standard and extended ACLs support IP fragments. ● Second and subsequent fragments are allowed because a Layer 4 rule cannot be applied to these fragments.
Example of Permitting All Packets from a Specified Host DellEMC(conf)#ip access-list extended ABC DellEMC(conf-ext-nacl)#permit tcp host 10.1.1.1 any eq 24 DellEMC(conf-ext-nacl)#deny ip any any fragment DellEMC(conf-ext-nacl) In the following example, the TCP packets that are first fragments or non-fragmented from host 10.1.1.1 with TCP destination port equal to 24 are permitted. Additionally, all TCP non-first fragments from host 10.1.1.1 are permitted.
seq 20 seq 25 seq 30 seq 35 seq 40 seq 45 seq 50 DellEMC# deny deny deny deny deny deny deny 10.4.0.0 /16 10.5.0.0 /16 10.6.0.0 /16 10.7.0.0 /16 10.8.0.0 /16 10.9.0.0 /16 10.10.0.0 /16 The following example shows how the seq command orders the filters according to the sequence number assigned. In the example, filter 25 was configured before filter 15, but the show config command displays the filters in the correct order. DellEMC(config-std-nacl)#seq 25 deny ip host 10.5.0.
seq 50 permit tcp 10.8.0.0 /16 10.50.188.118 /31 eq 49 monitor 349 seq 55 permit udp 10.15.1.0 /24 10.50.188.118 /31 range 1812 1813 To delete a filter, enter the show config command in IP ACCESS LIST mode and locate the sequence number of the filter you want to delete. Then use the no seq sequence-number command in IP ACCESS LIST mode.
NOTE: When assigning sequence numbers to filters, you may have to insert a new filter. To prevent reconfiguring multiple filters, assign sequence numbers in multiples of five or another number. The example below shows how the seq command orders the filters according to the sequence number assigned. In the example, filter 15 was configured before filter 5, but the show config command displays the filters in the correct order. DellEMC(config-ext-nacl)#seq 15 deny ip host 112.45.0.
● When Dell EMC Networking OS switches the packets, the egress L3 ACL filters the packet. For the following features, if you enable counters on rules that have already been configured and a new rule is either inserted or prepended, all the existing counters are reset: ● L2 ingress access list ● L3 egress access list ● L2 egress access list If a rule is simply appended, existing counters are not affected. Table 7.
ip access-list [standard | extended] name To view which IP ACL is applied to an interface, use the show config command in INTERFACE mode, or use the show running-config command in EXEC mode. DellEMC(conf-if)#show conf ! interface TenGigabitEthernet 1/1 ip address 10.2.1.100 255.255.255.0 ip access-group nimule in no shutdown DellEMC(conf-if)# To filter traffic on Telnet sessions, use only standard ACLs in the access-class command.
Configure Egress ACLs Egress ACLs are applied to line cards and affect the traffic leaving the system. Configuring egress ACLs onto physical interfaces protects the system infrastructure from attack — malicious and incidental — by explicitly allowing only authorized traffic. These system-wide ACLs eliminate the need to apply ACLs onto each interface and achieves the same results. By localizing target traffic, it is a simpler implementation. To restrict egress traffic, use an egress ACL.
1. Apply Egress ACLs to IPv4 system traffic. CONFIGURATION mode ip control-plane [egress filter] 2. Apply Egress ACLs to IPv6 system traffic. CONFIGURATION mode ipv6 control-plane [egress filter] 3. Create a Layer 3 ACL using permit rules with the count option to describe the desired CPU traffic.
For a complete listing of all commands related to prefix lists, refer to the Dell EMC Networking OS Command Line Interface Reference Guide. Creating a Prefix List To create a prefix list, use the following commands. 1. Create a prefix list and assign it a unique name. You are in PREFIX LIST mode. CONFIGURATION mode ip prefix-list prefix-name 2. Create a prefix list with a sequence number and a deny or permit action.
The example shows a prefix list in which the sequence numbers were assigned by the software. The filters were assigned sequence numbers based on the order in which they were configured (for example, the first filter was given the lowest sequence number). The show config command in PREFIX LIST mode displays two filters with the sequence numbers 5 and 10. DellEMC(conf-nprefixl)#permit 123.23.0.0 /16 DellEMC(conf-nprefixl)#deny 133.24.56.
CONFIGURATION mode router rip ● Apply a configured prefix list to incoming routes. You can specify an interface. If you enter the name of a nonexistent prefix list, all routes are forwarded. CONFIG-ROUTER-RIP mode distribute-list prefix-list-name in [interface] ● Apply a configured prefix list to outgoing routes. You can specify an interface or type of route. If you enter the name of a non-existent prefix list, all routes are forwarded.
you configure two remarks with the same sequence number and different strings, the second one replaces the first string. You cannot configure two or more remarks with the same string and different sequence numbers. To remove a remark, use the no remark command with the remark string and with or without the sequence number. If there is a matching string, the system deletes the remark. Configuring a Remark To write a remark for an ACL, follow these steps: 1. Create either an extended IPv4 or IPv6 ACL.
ACL Resequencing ACL resequencing allows you to re-number the rules and remarks in an access or prefix list. The placement of rules within the list is critical because packets are matched against rules in sequential order. To order new rules using the current numbering scheme, use resequencing whenever there is no opportunity. For example, the following table contains some rules that are numbered in increments of 1.
DellEMC# end DellEMC# resequence access-list ipv4 test 2 2 DellEMC# show running-config acl ! ip access-list extended test remark 2 XYZ remark 4 this remark corresponds to permit any host 1.1.1.1 seq 4 permit ip any host 1.1.1.1 remark 6 this remark has no corresponding rule remark 8 this remark corresponds to permit ip any host 1.1.1.2 seq 8 permit ip any host 1.1.1.2 seq 10 permit ip any host 1.1.1.3 seq 12 permit ip any host 1.1.1.4 Remarks that do not have a corresponding rule are incremented as a rule.
Logging of ACL Processes This functionality is supported on the platform. To assist in the administration and management of traffic that traverses the device after being validated by the configured ACLs, you can enable the generation of logs for access control list (ACL) processes.
● A maximum of 125 ACL entries with permit action can be logged. A maximum of 126 ACL entries with deny action can be logged. ● For virtual ACL entries, the same match rule number is reused. Similarly, when an ACL entry is deleted that was previously enabled for ACL logging, the match rule number used by it is released back to the pool or available set of match indices so that it can be reused for subsequent allocations.
Behavior of Flow-Based Monitoring You can activate flow-based monitoring for a monitoring session using the flow-based enable command in the Monitor Session mode. When you enable this flow-based monitoring, traffic with particular flows that are traversing through the interfaces are examined in accordance with the applied ACLs. By default, flow-based monitoring is not enabled. There are two ways in which you can enable flow-based monitoring in Dell EMC Networking OS.
The show ip accounting commands have been enhanced to display whether monitoring is enabled for traffic that matches with the rules of the specific ACL. Example Output of the show Command DellEMC# show ip accounting access-list ! Extended Ingress IP access list kar on TenGigabitEthernet 1/1 Total cam count 1 seq 5 permit ip 192.168.20.0/24 173.168.20.
DellEMC(conf)#do show monitor session 0 DellEMC(conf-mon-sess-0)#do show monitor session 0 SessID Source Destination Dir Mode Source IP TTL Drop Rate Gre-Protocol FcMonitor ------ ------------------ ---- -------------- -------------- --------0 Te 1/1 Te 1/2 rx Flow 0.0.0.0 0 No N/A N/A yes DellEMC# Dest IP DSCP -------- ---- 0.0.0.0 0 Configuring UDF ACL To configure a User Defined Field (UDF) ACL: 1. Enable UDF ACL feature on a switch.
Ipv4Qos : L2Qos : L2PT : IpMacAcl : VmanQos : EcfmAcl : FcoeAcl : iscsiOptAcl : ipv4pbr : vrfv4Acl : Openflow : fedgovacl : nlbclusteracl: 2 1 0 0 0 2 4 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 DellEMC# 4. Create a UDF packet format in the UDF TCAM table. CONFIGURATION mode udf-tcam name seq number DellEMC(conf)#udf-tcam ipnip seq 1 5. Configure a UDF ID to parse packet headers using the specified number of offset and required bytes.
10. Assign a value to a UDF ID. CONFIGURATION-UDF-Qualifier-Value Profile mode udf-id 1-12 value mask DellEMC(conf-udf-tcam-qual-val)#udf-id 1 aa ff 11. Associate the UDF qualifier value with a UDF packet profile in an IP access list.
ip mirror-access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id] [optimized] Dell(conf-if-te-0/4)#ip mirror-access-group acl3 in To view which IP mirror-access-group is applied to an interface, use the show config command in INTERFACE mode, or use the show running-config command in EXEC mode.
8 Bidirectional Forwarding Detection (BFD) BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no routing protocol is used. BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake.
BFD Packet Format Control packets are encapsulated in user datagram protocol (UDP) packets. The following illustration shows the complete encapsulation of a BFD control packet inside an IPv4 packet. Figure 9. BFD in IPv4 Packet Format Field Description Diagnostic Code The reason that the last session failed. State The current local session state. Refer to BFD Sessions. Flag A bit that indicates packet function.
Field Description Your Discriminator A random number generated by the remote system to identify the session. Discriminator values are necessary to identify the session to which a control packet belongs because there can be many sessions running on a single interface. Desired Min TX Interval The minimum rate at which the local system would like to send control packets to the remote system.
State Description Init The local system is communicating. Up Both systems are exchanging control packets. The session is declared down if: ● A control packet is not received within the detection time. ● Sufficient echo packets are lost. ● Demand mode is active and a control packet is not received in response to a poll packet. BFD Three-Way Handshake A three-way handshake must take place between the systems that participate in the BFD session.
Session State Changes The following illustration shows how the session state on a system changes based on the status notification it receives from the remote system. For example, if a session on a system is down and it receives a Down status notification from the remote system, the session state on the local system changes to Init. Figure 11.
● ● ● ● ● Configure BFD for OSPFv3 Configure BFD for IS-IS Configure BFD for BGP Configure BFD for VRRP Configuring Protocol Liveness Configure BFD for Physical Ports Configuring BFD for physical ports is supported on the C-Series and E-Series platforms only. BFD on physical ports is useful when you do not enable the routing protocol. Without BFD, if the remote system fails, the local system does not remove the connected route until the first failed attempt to send a packet.
Remote Addr: 2.2.2.
Establishing Sessions for Static Routes for Default VRF Sessions are established for all neighbors that are the next hop of a static route on the default VRF. Figure 12. Establishing Sessions for Static Routes To establish a BFD session, use the following command. ● Establish BFD sessions for all neighbors that are the next hop of a static route.
Example Configuration and Verification The following example contains static routes for both default and nondefault VRFs. Dell#sh run | grep bfd bfd enable ip route bfd prefix-list p4_le ip route bfd vrf vrf1 ip route bfd vrf vrf2 ip route bfd vrf vrf1 prefix-list p4_le The following example shows that sessions are created for static routes for the default VRF.
Prefix lists are used in route maps and route filtering operations. You can use prefix lists as an alternative to existing access lists (ACLs). A prefix is a portion of the IP address. Prefix lists constitute any number of bits in an IP address starting from the far left bit of the far left octet. By specifying the exactly number of bits in an IP address that belong to a prefix list, the prefix list can be used to aggregate addresses and perform some functions; for example, redistribution.
no ip route bfd [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] Configure BFD for IPv6 Static Routes BFD offers systems a link state detection mechanism for static routes. With BFD, systems are notified to remove static routes from the routing table as soon as the link state change occurs, rather than waiting until packets fail to reach their next hop. Configuring BFD for IPv6 static routes is a three-step process: 1. Enable BFD globally. 2.
ipv6 route bfd vrf vrf-name [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] Example Configuration and Verification The following example contains static routes for both default and nondefault VRFs. Dell#show run | grep bfd bfd enable ipv6 route bfd prefix-list p6_le ipv6 route bfd vrf vrf1 ipv6 route bfd vrf vrf2 ipv6 route bfd vrf vrf1 prefix-list p6_le The following example shows that sessions are created for static routes for the default VRF.
Changing IPv6 Static Route Session Parameters BFD sessions are configured with default intervals and a default role. The parameters you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all static routes. If you change a parameter, the change affects all sessions for static routes. To change parameters for static route sessions, use the following command . ● Change parameters for all static route sessions.
Establishing Sessions with OSPF Neighbors for the Default VRF BFD sessions can be established with all OSPF neighbors at once or sessions can be established with all neighbors out of a specific interface. Sessions are only established when the OSPF adjacency is in the Full state. Figure 13. Establishing Sessions with OSPF Neighbors To establish BFD with all OSPF neighbors or with OSPF neighbors on a single interface, use the following commands. ● Enable BFD globally.
The bold line shows the OSPF BFD sessions. R2(conf-router_ospf)#bfd all-neighbors R2(conf-router_ospf)#do show bfd neighbors * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients * 2.2.2.2 2.2.2.1 Te 2/1 Up 100 100 3 O * 2.2.3.1 2.2.3.2 Te 2/2 Up 100 100 3 O Establishing Sessions with OSPF Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, follow this procedure: ● Enable BFD globally.
* 6.1.1.1 6.1.1.2 Vl 30 Up 200 200 3 O * 7.1.1.1 7.1.1.2 Te 1/21 Up 200 200 3 O The following example shows the show bfd vrf neighbors command output showing the nondefault VRF. show bfd vrf VRF_blue neighbors * Ad Dn B C I O O3 R M V VT - Active session role Admin Down BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr * 5.1.1.1 RemoteAddr 5.1.1.2 Interface Po 30 State Rx-int Tx-int Mult VRF Clients Up 200 200 3 255 O * 6.1.1.1 6.1.1.
Role: Active Delete session on Down: True VRF: VRF_blue Client Registered: OSPF Uptime: 00:00:15 Statistics: Number of packets received from neighbor: 78 Number of packets sent to neighbor: 78 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Session Discriminator: 6 Neighbor Discriminator: 1 Local Addr: 7.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 7.1.1.
To disable BFD sessions, use the following commands. ● Disable BFD sessions with all OSPF neighbors. ROUTER-OSPF mode no bfd all-neighbors ● Disable BFD sessions with all OSPF neighbors on an interface. INTERFACE mode ip ospf bfd all-neighbors disable Configure BFD for OSPFv3 BFD for OSPFv3 provides support for IPV6. Configuring BFD for OSPFv3 is a two-step process: 1. Enable BFD globally. 2. Establish sessions with OSPFv3 neighbors.
* fe80::2a0:c9ff:fe00:2 O3 DellEMC# fe80::3617:98ff:fe34:12 Vl 2 Up 200 200 3 Establishing BFD Sessions with OSPFv3 Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, use the following procedure: ● Enable BFD globally. CONFIGURATION mode bfd enable ● Establish sessions with all OSPFv3 neighbors in a specific VRF. ROUTER-OSPFv3 mode bfd all-neighbors ● Establish sessions with the OSPFv3 neighbors on a single interface in a specific VRF.
* fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 100 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 101 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 102 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 DellEMC# fe80::3617:98ff:fe34:12 Vl 103 Up 150 150 3 Changing OSPFv3 Session Parameters Configure BFD sessions with default intervals and a default role.
Related Configuration Tasks ● Changing IS-IS Session Parameters ● Disabling BFD for IS-IS Establishing Sessions with IS-IS Neighbors BFD sessions can be established for all IS-IS neighbors at once or sessions can be established for all neighbors out of a specific interface. Figure 14. Establishing Sessions with IS-IS Neighbors To establish BFD with all IS-IS neighbors or with IS-IS neighbors on a single interface, use the following commands. ● Establish sessions with all IS-IS neighbors.
C I O R - CLI - ISIS - OSPF - Static Route (RTM) LocalAddr * 2.2.2.2 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 Te 2/1 Up 100 100 3 I Changing IS-IS Session Parameters BFD sessions are configured with default intervals and a default role. The parameters that you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all IS-IS sessions or all IS-IS sessions out of an interface.
Figure 15. Establishing Sessions with BGP Neighbors The sample configuration shows alternative ways to establish a BFD session with a BGP neighbor: ● By establishing BFD sessions with all neighbors discovered by BGP (the bfd all-neighbors command). ● By establishing a BFD session with a specified BGP neighbor (the neighbor {ip-address | peer-group-name} bfd command) BFD packets originating from a router are assigned to the highest priority egress queue to minimize transmission delays.
bfd enable 2. Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3. Add a BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group name} remote-as as-number 4. Enable the BGP neighbor. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group-name} no shutdown 5. Add a BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP mode neighbor {ipv6-address | peer-group name} remote-as as-number 6.
2. Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3. Specify the address family as IPv4. CONFIG-ROUTERBGP mode address-family ipv4 vrf vrf-name 4. Add an IPv4 BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP_ADDRESSFAMILY mode neighbor {ip-address | peer-group name} remote-as as-number 5. Enable the BGP neighbor. CONFIG-ROUTERBGP_ADDRESSFAMILY mode neighbor {ip-address | peer-group-name} no shutdown 6.
Disabling BFD for BGP You can disable BFD for BGP. To disable a BFD for BGP session with a specified neighbor, use the first command. To remove the disabled state of a BFD for BGP session with a specified neighbor, use the second command. The BGP link with the neighbor returns to normal operation and uses the BFD session parameters globally configured with the bfd all-neighbors command or configured for the peer group to which the neighbor belongs. ● Disable a BFD for BGP session with a specified neighbor.
V - VRRP LocalAddr * 1.1.1.3 * 2.2.2.3 * 3.3.3.3 RemoteAddr 1.1.1.2 2.2.2.2 3.3.3.2 Interface Te 6/1 Te 6/2 Te 6/3 State Up Up Up Rx-int 200 200 200 Tx-int 200 200 200 Mult 3 3 3 Clients B B B The following example shows viewing BFD neighbors with full detail. The bold lines show the BFD session parameters: TX (packet transmission), RX (packet reception), and multiplier (maximum number of missed packets).
3 neighbor(s) using 24168 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 1.1.1.2 2.2.2.2 3.3.3.2 0 0 0 1 1 1 282 273 282 281 273 281 0 0 0 0 0 0 0 (0) 0 00:38:12 04:32:26 00:38:12 The following example shows viewing BFD information for a specified neighbor.
BGP version 4, remote router ID 12.0.0.4 BGP state ESTABLISHED, in this state for 00:05:33 ... Neighbor is using BGP peer-group mode BFD configuration Peer active in peer-group outbound optimization ... Configure BFD for VRRP When using BFD with VRRP, the VRRP protocol registers with the BFD manager on the route processor module (RPM). BFD sessions are established with all neighboring interfaces participating in VRRP.
vrrp bfd all-neighbors Establishing VRRP Sessions on VRRP Neighbors The master router does not care about the state of the backup router, so it does not participate in any VRRP BFD sessions. VRRP BFD sessions on the backup router cannot change to the UP state. Configure the master router to establish an individual VRRP session the backup router. To establish a session with a particular VRRP neighbor, use the following command. ● Establish a session with a particular VRRP neighbor.
INTERFACE mode vrrp bfd neighbor ip-address interval milliseconds min_rx milliseconds multiplier value role [active | passive] To view session parameters, use the show bfd neighbors detail command. Disabling BFD for VRRP If you disable any or all VRRP sessions, the sessions are torn down. A final Admin Down control packet is sent to all neighbors and sessions on the remote system change to the Down state.
9 Border Gateway Protocol (BGP) Border Gateway Protocol (BGP) is an interdomain routing protocol that manages routing between edge routers. BGP uses an algorithm to exchange routing information between switches enabled with BGP. BGP determines a path to reach a particular destination using certain attributes while avoiding routing loops. BGP selects a single path as the best path to a destination network or host. You can also influence BGP to select different path by altering some of the BGP attributes.
the knowledge to reach routers external to the AS. EBGP routers exchange information with other EBGP routers as well as IBGP routers to maintain connectivity and accessibility. Figure 17. BGP Topology with autonomous systems (AS) BGP version 4 (BGPv4) supports classless interdomain routing (CIDR) and aggregate routes and AS paths. BGP is a path vector protocol — a computer network in which BGP maintains the path that updated information takes as it diffuses through the network.
Figure 18. BGP Routers in Full Mesh The number of BGP speakers each BGP peer must maintain increases exponentially. Network management quickly becomes impossible. AS4 Number Representation Dell EMC Networking OS supports multiple representations of 4-byte AS numbers: asplain, asdot+, and asdot. NOTE: The ASDOT and ASDOT+ representations are supported only with the 4-Byte AS numbers feature. If 4-Byte AS numbers are not implemented, only ASPLAIN representation is supported.
● All AS numbers between 0 and 65535 are represented as a decimal number, when entered in the CLI and when displayed in the show commands outputs. ● AS Numbers larger than 65535 is represented using ASDOT notation as .. For example: AS 65546 is represented as 1.10. ASDOT representation combines the ASPLAIN and ASDOT+ representations.
DellEMC(conf-router_bgp)#do sho ip bgp BGP table version is 28093, local router ID is 172.30.1.57 AS4 SUPPORT DISABLED DellEMC(conf-router_bgp)#no bgp four-octet-as-support DellEMC(conf-router_bgp)#sho conf ! router bgp 100 neighbor 172.30.1.250 local-as 65057 DellEMC(conf-router_bgp)#do show ip bgp BGP table version is 28093, local router ID is 172.30.1.57 Four-Byte AS Numbers You can use the 4-Byte (32-bit) format when configuring autonomous system numbers (ASNs).
State Description Idle BGP initializes all resources, refuses all inbound BGP connection attempts, and initiates a TCP connection to the peer. Connect In this state the router waits for the TCP connection to complete, transitioning to the OpenSent state if successful. If that transition is not successful, BGP resets the ConnectRetry timer and transitions to the Active state when the timer expires. Active The router resets the ConnectRetry timer to zero and returns to the Connect state.
Best Path Selection Criteria Paths for active routes are grouped in ascending order according to their neighboring external AS number (BGP best path selection is deterministic by default, which means the bgp non-deterministic-med command is NOT applied). The best path in each group is selected based on specific criteria. Only one “best path” is selected at a time. If any of the criteria results in more than one path, BGP moves on to the next option in the list.
7. 8. 9. 10. 11. 12. 13. a. This comparison is only done if the first (neighboring) AS is the same in the two paths; the MEDs are compared only if the first AS in the AS_SEQUENCE is the same for both paths. b. If you entered the bgp always-compare-med command, MEDs are compared for all paths. c. Paths with no MED are treated as “worst” and assigned a MED of 4294967295. Prefer external (EBGP) to internal (IBGP) paths or confederation EBGP paths.
Figure 20. BGP Local Preference Multi-Exit Discriminators (MEDs) If two ASs connect in more than one place, a multi-exit discriminator (MED) can be used to assign a preference to a preferred path. MED is one of the criteria used to determine the best path, so keep in mind that other criteria may impact selection, as shown in the illustration in Best Path Selection Criteria. One AS assigns the MED a value and the other AS uses that value to decide the preferred path.
Figure 21. Multi-Exit Discriminators NOTE: Configuring the set metric-type internal command in a route-map advertises the IGP cost as MED to outbound EBGP peers when redistributing routes. The configured set metric value overwrites the default IGP cost. If the outbound route-map uses MED, it overwrites IGP MED. Origin The origin indicates the origin of the prefix, or how the prefix came into BGP. There are three origin codes: IGP, EGP, INCOMPLETE.
The AS path is shown in the following example. The origin attribute is shown following the AS path information (shown in bold).
the unicast and multicast BGP database to form a routing table for unicast and multicast. You can configure BGP peers that exchange both unicast and multicast Network Layer Reachability Information (NLRI) in which MBGP routes is redistributed into BGP. The default is IPv4 unicast. IPv4 and IPv6 address family The IPv4 address family configuration in Dell EMC Networking OS is used for identifying routing sessions for protocols that use IPv4 address. You can specify multicast within the IPv4 address family.
BGP global configuration default values By default, BGP is disabled. The following table displays the default values for BGP on Dell EMC Networking OS. Table 9. BGP Default Values Item Default BGP Neighbor Adjacency changes All BGP neighbor changes are logged.
● If the redistribute command has metric configured (route-map set metric or redistribute route-type metric) and the BGP peer outbound route-map has metric-type internal configured, BGP advertises the metric configured in the redistribute command as MED. ● If BGP peer outbound route-map has metric configured, all other metrics are overwritten by this configuration. NOTE: When redistributing static, connected, or OSPF routes, there is no metric option.
Figure 22. Before and After AS Number Migration with Local-AS Enabled When you complete your migration, and you have reconfigured your network with the new information, disable this feature. If you use the “no prepend” option, the Local-AS does not prepend to the updates received from the eBGP peer. If you do not select “no prepend” (the default), the Local-AS is added to the first AS segment in the AS-PATH.
● Configure inbound BGP soft-reconfiguration on a peer for f10BgpM2PrefixInPrefixesRejected to display the number of prefixes filtered due to a policy. If you do enable BGP soft-reconfig, the denied prefixes are not accounted for. ● F10BgpM2AdjRibsOutRoute stores the pointer to the NLRI in the peer's Adj-Rib-Out. ● PA Index (f10BgpM2PathAttrIndex field in various tables) is used to retrieve specific attributes from the PA table.
Basic BGP configuration tasks The following sections describe how to configure a basic BGP network and the basic configuration tasks that are required for the BGP to be up and running.
neighbor {ip-address | ipv6-address| peer-group name} remote-as as-number ● ip-address: IPv4 address of the neighbor ● ipv6-address: IPv6 address of the neighbor ● peer-group name: Name of the peer group. It can contain 16 characters. ● as-number: Autonomous number NOTE: Neighbors that are defined using the neighbor remote-as command in the CONFIGURATION-ROUTERBGP mode exchange IPv4 unicast address prefixes only. 3. Enable the BGP neighbor.
The third line of the show ip bgp neighbors output contains the BGP State. If anything other than ESTABLISHED is listed, the neighbor is not exchanging information and routes. For more information about using the show ip bgp neighbors command, refer to the Dell EMC Networking OS Command Line Interface Reference Guide. The following example shows the show ip bgp neighbors command output. DellEMC#show ip bgp neighbors BGP neighbor is 20.20.20.1, remote AS 20, external link BGP remote router ID 1.1.1.
1 neighbor(s) using 40960 bytes of memory Neighbor 20.20.20.1 AS 200 MsgRcvd 0 MsgSent 0 TblVer 0 InQ 0 OutQ Up/Down State/Pfx 0 00:00:00 0 Changing a BGP router ID BGP uses the configured router ID to identify the devices in the network. By default, the router ID is the highest IP address of the Loopback interface. If no Loopback interfaces are configured, the highest IP address of a physical interface on the router is used as the BGP router ID.
bgp asnotation asplain NOTE: ASPLAIN is the default method Dell EMC Networking OS uses and does not appear in the configuration display. ● Enable ASDOT AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asdot ● Enable ASDOT+ AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asdot+ The following example shows the bgp asnotation asplain command output.
CONFIG mode router bgp as-number ● Add the IP address of the neighbor for the specified autonomous system. CONFIG-ROUTER-BGP mode neighbor {ip-address | ipv6–address | peer-group-name} remote-as as-number ● Enable the neighbor. CONFIG-ROUTERBGP mode neighbor ip-address | ipv6-address | peer-group-name no shutdown ● Specify the IPv4 address family configuration. CONFIG-ROUTER-BGP mode address-family ipv4 [multicast | vrf vrf-name] multicast — Specifies the IPv4 multicast address family.
To support your own IP addresses, interfaces, names, and so on, you can copy and paste from these examples to your CLI. Be sure that you make the necessary changes. Example-Configuring BGP routing between peers Example of enabling BGP in Router A Following is an example to enable BGP configuration in the router A. RouterA# configure terminal RouterA(conf)# router bgp 40000 RouterA(conf-router_bgp)# bgp router-id 10.1.1.99 RouterA(conf-router_bgp)# timers bgp 80 130 RouterA(conf-router_bgp)# neighbor 192.
● You must create a peer group first before adding the neighbors in the peer group. ● If you remove any configuration parameters from a peer group, it will apply to all the neighbors configured under that peer group. ● If you have not configured a parameter for an individual neighbor in the peer group, the neighbor uses the value configured in the peer group. ● If you reset any parameter for an individual neighbor, it will override the value set in the peer group.
To add an internal BGP (IBGP) neighbor, configure the as-number parameter with the same BGP as-number configured in the router bgp as-number command. After you create a peer group, you can use any of the commands beginning with the keyword neighbor to configure that peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
Example-Configuring BGP peer groups The following example configurations show how to enable BGP and set up some peer groups. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations. To support your own IP addresses, interfaces, names, and so on, you can copy and paste from these examples to your CLI. Be sure that you make the necessary changes. The following illustration shows the configurations described on the following examples.
R1(conf-if-gi-1/31)#show config ! interface GigabitEthernet 1/31 ip address 10.0.3.31/24 no shutdown R1(conf-if-gi-1/31)#exit R1(conf)#ip route 192.168.128.2/32 10.0.1.22 R1(conf)#router bgp 99 R1(conf-router_bgp)#neighbor 192.168.128.2 remote 99 R1(conf-router_bgp)#neighbor 192.168.128.2 no shut R1(conf-router_bgp)#neighbor 192.168.128.2 update-source loop 0 R1(conf-router_bgp)#neighbor 10.0.3.33 remote 100 R1(conf-router_bgp)#neighbor 10.0.3.
R3(conf-if-te-3/11)#no shutdown R3(conf-if-te-3/11)#show config ! interface TengigabitEthernet 3/11 ip address 10.0.3.33/24 no shutdown R3(conf-if-te-3/11)#int te 3/21 R3(conf-if-te-3/21)#ip address 10.0.2.3/24 R3(conf-if-te-3/21)#no shutdown R3(conf-if-te-3/21)#show config ! interface TengigabitEthernet 3/21 ip address 10.0.2.3/24 no shutdown R3(conf-if-te-3/21)# R3(conf-if-te-3/21)#router bgp 100 R3(conf-router_bgp)#show config ! router bgp 100 R3(conf-router_bgp)#neighbor 10.0.3.
Example of Enabling Peer Groups (Router 2) R2#conf R2(conf)#router bgp 99 R2(conf-router_bgp)# neighbor CCC peer-group R2(conf-router_bgp)# neighbor CC no shutdown R2(conf-router_bgp)# neighbor BBB peer-group R2(conf-router_bgp)# neighbor BBB no shutdown R2(conf-router_bgp)# neighbor 192.168.128.1 peer AAA R2(conf-router_bgp)# neighbor 192.168.128.1 no shut R2(conf-router_bgp)# neighbor 192.168.128.3 peer BBB R2(conf-router_bgp)# neighbor 192.168.128.
Advanced BGP configuration tasks The following sections describe how to configure the advanced (optional) BGP configuration tasks. Route-refresh and Soft-reconfiguration BGP soft-reconfiguration allows for faster and easier route changing. Changing routing policies typically requires a reset of BGP sessions (the TCP connection) for the policies to take effect. Such resets cause undue interruption to traffic due to hard reset of the BGP cache and the time it takes to re-establish the session.
Route-refresh This section explains how the soft-reconfiguration and route-refresh works. Soft-reconfiguration has to be configured explicitly for a neighbor unlike route refresh, which is automatically negotiated between BGP peers when establishing a peer session. The route-refresh updates will be sent, only if the neighbor soft-reconfiguration inbound command is not configured in a BGP neighbor and when you do a soft reset using clear ip bgp {neighbor-address | peer-groupname} soft in command.
redistribute connected neighbor 20.1.1.2 remote-as 200 neighbor 20.1.1.2 no shutdown neighbor 20::2 remote-as 200 neighbor 20::2 no shutdown ! address-family ipv6 unicast redistribute connected neighbor 20::2 activate exit-address-family ! DellEMC(conf-router_bgp)#do clear ip bgp 20.1.1.2 soft in May 8 15:28:11 : BGP: 20.1.1.2 sending ROUTE_REFRESH AFI/SAFI (1/1) May 8 15:28:12 : BGP: 20.1.1.2 UPDATE rcvd packet len 56 May 8 15:28:12 : BGP: 20.1.1.2 rcvd UPDATE w/ attr: origin ?, path 200, nexthop 20.1.1.
○ suppress-map map-name-Create aggregate route by suppressing the advertisements of specific routes. ○ advertise-map map-name-Create aggregate route by advertising specific routes. Configuring BGP aggregate routes To create an aggregate route entry in the BGP routing table, use the following commands. The aggregate route is advertised from the autonomous system. ● Enter the router configuration mode and the AS number for the specific BGP routing process.
DellEMC(conf-router_bgp)# aggregate-address 10.1.1.0/24 suppress-map map1 DellEMC(conf-router_bgp)# exit DellEMC(conf)# The route-map named map1 can have any action such as permit and sequence number configured, so that the advertisement of aggregate routes can be suppressed based on the set action in the route-map. Following is the sample configuration to suppress the advertisement of specific aggregate routes to all neighbors.
As seen in the following example, the expressions are displayed when using the show commands. To view the AS-PATH ACL configuration, use the show config command in CONFIGURATION AS-PATH ACL mode and the show ip as-pathaccess-list command in EXEC Privilege mode. For more information about this command and route filtering, refer to Filtering BGP Routes. The following example applies access list Eagle to routes inbound from BGP peer 10.5.5.2.
NOTE: When you configure a new set of BGP policies, to ensure the changes are made, always reset the neighbor or peer group by using the clear ip bgp command in EXEC Privilege mode. Filtering BGP using IP prefix lists An IP prefix lists contains a list of networks. When applying an IP prefix list to a BGP neighbor, you can able to send or receive the routes whose destination is in the IP prefix list. Filtering BGP routes based on IP prefix lists involves the following steps: ● Create a prefix list.
10.10.10.2. So the routes from 10.10.10.1/24 network is distributed to neighbor 10.10.10.2 since the IP prefix list route10 explicitly permits the routes to be distributed to the neighbor. To view the BGP configuration, use the show config command in ROUTER BGP mode. To view a prefix list configuration, use the show ip prefix-list detail or show ip prefix-list summary commands in EXEC Privilege mode. Filtering BGP Routes Using Route Maps To filter routes using a route map, use these commands. 1.
To configure an AS-PATH ACL to filter a specific AS_PATH value, use these commands in the following sequence. 1. Assign a name to a AS-PATH ACL and enter AS-PATH ACL mode. CONFIGURATION mode ip as-path access-list as-path-name 2. Enter the parameter to match BGP AS-PATH for filtering. CONFIG-AS-PATH mode {deny | permit} filter parameter This is the filter that is used to match the AS-path. The entries can be any format, letters, numbers, or regular expressions.
CONFIG-ROUTE-MAP mode match {community community-list-name [exact] | extcommunity extcommunity-list-name [exact]} 3. Return to CONFIGURATION mode. CONFIG-ROUTE-MAP mode exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number AS-number: 0 to 65535 (2-Byte) or 1 to 4294967295 (4-Byte) or 0.1 to 65535.65535 (Dotted format) 5. Apply the route map to the neighbor or peer group’s incoming or outgoing routes.
DellEMC(conf-router_bgp)# neighbor 10.10.10.1 fall-over DellEMC(conf-router_bgp)# exit DellEMC(conf-router_bgp)# To verify that you enabled fast fall-over on a particular BGP neighbor, use the show ip bgp neighbors command. Because fast fall-over is disabled by default, it appears only if it has been enabled (shown in bold). DellEMC#show ip bgp neighbors BGP neighbor is 10.10.10.1, remote AS 500, internal link Member of peer-group test for session parameters BGP version 4, remote router ID 30.30.30.
neighbor neighbor neighbor neighbor neighbor neighbor neighbor DellEMC# test peer-group test fall-over test no shutdown 10.10.10.1 remote-as 500 10.10.10.1 fall-over 10.10.10.1 update-source Loopback 0 10.10.10.1 no shutdown Configuring Passive Peering When you enable a peer-group, the software sends an OPEN message to initiate a TCP connection. If you enable passive peering for the peer group, the software does not send an OPEN message, but it responds to an OPEN message.
● Save all forwarding information base (FIB) and content addressable memory (CAM) entries on the line card and continue forwarding traffic while the secondary route processor module (RPM) is coming online. ● Advertise to all BGP neighbors and peer-groups that the forwarding state of all routes has been saved. This prompts all peers to continue saving the routes they receive and to continue forwarding traffic.
○ metric value: The value is from 0 to 16777215. The default is 0. ○ route-map map-name: Specify the name of a configured route map to be consulted before adding the ISIS route. ● Include specific OSPF routes into BGP. ROUTER BGP or CONF-ROUTER_BGPv6_ AF mode redistribute ospf process-id [match external {1 | 2} | match internal] [metric-type {external | internal}] [route-map map-name] Configure the following parameters: ○ ospf: Indicates that you are redistributing OSPF routes in BGP.
! neighbor 20::2 activate neighbor 20::3 activate exit-address-family interface Vlan 10 ip address 10.10.10.1/24 ipv6 address 10::1/64 ipv6 ospf 1 area 0 tagged Port-channel 10 ip ospf priority 255 no shutdown The following is an example configuration of redistributing iBGP routes into OSPF with a non-default VRF: interface Vlan 11 ip vrf forwarding core1 ip address 11.11.11.1/24 ipv6 address 11::1/64 ipv6 ospf 11 area 0 tagged Port-channel 10 ip ospf priority 255 ! router ospf 11 vrf core1 router-id 11.
exit-address-family ! interface Vlan 10 ip address 10.10.10.2/24 ipv6 address 10::2/64 tagged Port-channel 10 ip router isis 100 ipv6 router isis 100 vrrp bfd all-neighbors ! vrrp-group 1 virtual-address 10.10.10.100 ! vrrp-ipv6-group 1 virtual-address 10::100 virtual-address fe80::10 no shutdown ! interface Vlan 11 ip vrf forwarding core1 ip address 11.11.11.2/24 ipv6 address 11::2/64 tagged Port-channel 10 ip router isis ipv6 router isis ! vrrp-group 1 virtual-address 11.11.11.
NOTE: The path-count parameter controls the number of paths that are advertised, not the number of paths that are received. DellEMC# configure terminal DellEMC(conf)# router bgp 400 DellEMC(conf-router_bgp)# neighbor 10.10.10.1 remote-as 500 DellEMC(conf-router_bgp)# bgp add-path both 2 DellEMC(conf-router_bgp)# address-family ipv4 multicast DellEMC(conf-router_bgp_af)# neighbor 10.10.10.1 activate DellEMC(conf-router_bgp_af)# neighbor 10.10.10.
deny 703:20 deny 704:20 deny 705:20 deny 14551:20 deny 701:112 deny 702:112 deny 703:112 deny 704:112 deny 705:112 deny 14551:112 deny 701:667 deny 702:667 deny 703:667 deny 704:666 deny 705:666 deny 14551:666 DellEMC# Configuring an IP Extended Community List To configure an IP extended community list, use these commands. 1. Create a extended community list and enter the EXTCOMMUNITY-LIST mode. CONFIGURATION mode ip extcommunity-list extcommunity-list-name 2.
Configure BGP attributes Following sections explain how to configure the BGP attributes such as MED, COMMUNITY, WEIGHT, and LOCAL_PREFERENCE. Changing MED Attributes By default, Dell EMC Networking OS uses the MULTI_EXIT_DISC or MED attribute when comparing EBGP paths received from different BGP neighbors or peers from the same AS for the same route. You can configure the device to compare the MED attributes from neighbors or peers in different AS using the bgp always-compare-med command.
● community-number: use AA:NN format where AA is the AS number (2 or 4 Bytes) and NN is a value specific to that autonomous system. ● local-AS: routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED and are not sent to EBGP peers. ● no-advertise: routes with the COMMUNITY attribute of NO_ADVERTISE and are not advertised. ● no-export: routes with the COMMUNITY attribute of NO_EXPORT. ● none: remove the COMMUNITY attribute. ● additive: add the communities to already existing communities. 3.
value: the range is from 0 to 4294967295. The default is 100. DellEMC# configure terminal DellEMC(conf)# router bgp 400 DellEMC(conf_router_bgp)# neighbor 10.10.10.1 remote-as 500 DellEMC(conf_router_bgp)# bgp default local-preference 150 DellEMC(conf_router_bgp)# exit In the above example configuration, the default LOCAL_PREFERENCE value is changed to 150 for all the updates from AS 500 to AS 400. The default value is 100.
● Disable next hop processing and configure the router (route reflector) as the next hop for a BGP neighbor. CONFIG-ROUTER-BGP mode neighbor {ip-address | ipv6-address | peer-group-name} next-hop-self [all] If you do not use the all keyword, the next hop of only eBGP-learned routes is updated by the route reflector. If you use the all keyword, the next hop of both eBGP- and iBGP-learned routes are updated by the route reflector. ● Sets the next hop address.
○ number: Maximum number of parallel paths. The range is from 2 to 64. DellEMC# configure terminal DellEMC(conf)# router bgp 400 DellEMC(conf-router_bgp)# maximum-paths ibgp 5 DellEMC(conf-router_bgp)# exit In the above example configuration, the maximum number of parallel internal BGP routes is set to 5, so that only 5 routes can be installed in a routing table. The show ip bgp network command includes multipath information for that network.
● Assign a cluster ID or an IP address to a router reflector cluster. CONFIG-ROUTER-BGP mode bgp cluster-id ip-address | number ○ ip-address: IP address as the route reflector cluster ID. ○ number: A route reflector cluster ID as a number from 1 to 4294967295. You can have multiple clusters in an AS. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors.
○ suppress: the range is from 1 to 20000. This number is compared to the flapping route’s Penalty value. If the Penalty value is greater than the suppress value, the flapping route is no longer advertised (that is, it is suppressed). The default is 2000.) ○ max-suppress-time: the range is from 1 to 255. The maximum number of minutes a route can be suppressed. The default is four times the half-life value. The default is 60 minutes. ○ route-map map-name: name of a configured route map.
route-map Route-map to specify criteria for dampening To view a count of dampened routes, history routes, and penalized routes when you enable route dampening, look at the seventh line of the show ip bgp summary command output, as shown in the following example (bold). DellEMC>show ip bgp summary BGP router identifier 10.114.8.
In the above example configuration, the BGP timers are set with keepalive time as 80 seconds with which the system sends keepalive messages to the BGP peer and holdtime as 120 seconds with which the system waits for a message from the BGP peer before concluding that the peer is dead. To view non-default values, use the show config command in CONFIGURATION ROUTER BGP mode or the show running-config bgp command in EXEC Privilege mode.
2. Shut down the BGP neighbors corresponding to the IPv4 unicast address family using the following command: shutdown address-family-ipv4-unicast To enable or disable BGP neighbors corresponding to IPv4 multicast address family: 1. Enter the router bgp mode using the following command: CONFIGURATION Mode router bgp as-number 2.
Match a Clause with a Continue Clause The continue feature can exist without a match clause. Without a match clause, the continue clause executes and jumps to the specified route-map entry. With a match clause and a continue clause, the match clause executes first and the continue clause next in a specified route map entry. The continue clause launches only after a successful match.
● Enter the router configuration mode and the AS number. CONFIG mode router bgp as-number ● Specify the IPv4 address family configuration. CONFIG-ROUTER-BGP mode address-family {ipv4 [multicast] | ipv6 unicast} vrf vrf-name vrf vrf-name — Specifies the name of VRF instance associated with the IPv4 or IPv6 address-family configuration. ● Add the IP address of the neighbor in the specified AS to the IPv4 MBGP neighbor table.
neighbor 50.0.0.2 activate exit-address-family ! address-family ipv6 unicast vrf vrf1 neighbor 50.0.0.2 activate exit-address-family DellEMC# Maintaining Existing AS Numbers During an AS Migration The local-as feature smooths out the BGP network migration operation and allows you to maintain existing ASNs during a BGP network migration. When you complete your migration, be sure to reconfigure your routers with the new information and disable this feature. ● Allow external routes from this neighbor.
○ peer-group-name: 16 characters. ○ Number: 1 through 10. Format: IP Address: A.B.C.D and IPv6 adress: X:X:X:X::X. You must Configure Peer Groups before assigning it to an AS. The lines shown in bold are the number of times ASN 65123 can appear in the AS path (allows–in 9). To disable this feature, use the no neighbor allow-as in number command in CONFIGURATION ROUTER BGP mode. R2(conf-router_bgp)#show conf ! router bgp 65123 bgp router-id 192.168.10.2 network 10.10.21.0/24 network 10.10.32.
MBGP support for IPv6 MBGP suports IPv6 with same features and functionality as IPv4 BGP. MBGP for IPv6 supports IPv6 address-family and Network Layer Reachability Information (NLRI) and next hop that uses IPv6 address. Configuring IPv6 MBGP between peers To configure IPv6 MBGP, use the following commands. Following are the steps to configure IPv6 MBGP between two peers. The neighbors that are configured using neighbor remote-as command exchange only the IPv4 unicast address prefixes.
Example-Configuring IPv4 and IPv6 neighbors Example of enabling BGP and address family configuration in router (R1) Following is an example to enable BGP and address family configuration for the neighbor R2 (20.20.20.2) in the router R1. R1(conf)# router bgp 10 R1(conf-router_bgp)# neighbor 20.20.20.2 remote-as 200 R1(conf-router_bgp)# neighbor 20.20.20.2 no shutdown R1(conf-router_bgp)# neighbor 2001::2 remote-as 200 R1(conf-router_bgp)# neighbor 2001::2 no shutdown R1(conf-router_bgp)# neighbor 30.30.30.
Following is the output of show ip bgp ipv6 unicast summary command for the above configuration example. R1#show ip bgp ipv6 unicast summary BGP router identifier 1.1.1.1, local AS number 10 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 2 neighbor(s) using 24576 bytes of memory Neighbor 20.20.20.
Configure IPv6 NH Automatically for IPv6 Prefix Advertised over IPv4 Neighbor You can configure the system to pick the next hop IPv6 address dynamically for IPv6 prefix advertised over an IPv4 neighbor configured under IPv6 address family. If there is no IPv6 address configured on the local interface, the system uses the IPv4 mapped IPv6 address. If there are multiple IPv6 addresses configured on the interface, the system uses the lowest IPv6 address configured on that interface.
! exit-address-family Example configuration performed in R2 DellEMC# configure terminal DellEMC(conf)# router bgp 20 DellEMC(conf-router_bgp)# neighbor 10.1.1.1 remote-as 655 DellEMC(conf-router_bgp)# neighbor 10.1.1.1 no shutdown DellEMC(conf-router_bgp)# address-family ipv6 unicast DellEMC(conf-router_bgpv6_af)# neighbor 10.1.1.1 activate DellECM(conf-router_bgpv6_af)# exit Following is the show running-config command output for the above configuration.
● View information about local BGP state changes and other BGP events. EXEC Privilege mode debug ip bgp [ip-address | peer-group peer-group-name] events [in | out] ● View information about BGP KEEPALIVE messages. EXEC Privilege mode debug ip bgp [ip-address | peer-group peer-group-name] keepalive [in | out] ● View information about BGP notifications received from or sent to neighbors.
For address family: IPv4 Unicast BGP table version 1395, neighbor version 1394 Prefixes accepted 1 (consume 4 bytes), 0 withdrawn by peer Prefixes advertised 0, rejected 0, 0 withdrawn from peer Connections established 3; dropped 2 Last reset 00:00:12, due to Missing well known attribute Notification History 'UPDATE error/Missing well-known attr' Sent : 1 Recv: 0 'Connection Reset' Sent : 1 Recv: 0 Last notification (len 21) sent 00:26:02 ago ffffffff ffffffff ffffffff ffffffff 00160303 03010000 Last notifi
10 Content Addressable Memory (CAM) CAM is a type of memory that stores information in the form of a lookup table. On Dell EMC Networking systems, CAM stores Layer 2 (L2) and Layer 3 (L3) forwarding information, access-lists (ACLs), flows, and routing policies.
Table 12. Default Cam Allocation Settings (continued) CAM Allocation Setting vrfv4Acl 0 Openflow 0 fedgovacl 0 NOTE: When you reconfigure CAM allocation, use the nlbclusteracl number command to change the number of NLB ARP entries. The range is from 0 to 2. The default value is 0. At the default value of 0, eight NLB ARP entries are available for use. This platform supports upto 512 CAM entries. Select 1 to configure 256 entries. Select 2 to configure 1024 entries.
cam-acl {default | l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number vman-qos | vman-dual-qos number ecfmacl number nlbcluster number ipv4pbr number openflow number | fcoe number iscsioptacl number [vrfv4acl number] NOTE: If you do not enter the allocation values for the CAM regions, the value is 0. 3. Execute write memory and verify that the new settings are written to the CAM on the next boot. EXEC Privilege mode show cam-acl 4. Reload the system.
L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : : : 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 2 2 0 0 DellEMC(conf)# NOTE: If you change the cam-acl setting from CONFIGURATION mode, the output of this command does not reflect any changes until you save the running-configuration and reload the chassis.
IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : 0 0 0 0 0 0 0 0 0 0 DellEMC# View CAM Usage View the amount of CAM space available, used, and remaining in each partition (including IPv4 and IPv6 Flow and Layer 2 ACL sub-partitions) using the show cam-usage command in EXEC Privilege mode The following output shows CAM blocks usage for Layer 2 and Layer 3 ACLs and other processes that use CAM space: Example of the show cam-usage Command Dell
The range of threshold value is from 1 to 100. The default threshold value is 90 percent. ● Assign the silence period for syslog warning. CONFIGURATION mode cam-threshold threshold {default | threshold-percent} silence-period {default | silenceperiod-value} The range of silence period is from 0 to 65535. The default is 0 seconds. NOTE: If you delete a FP in a CAM region that is assigned with threshold, a syslog warning appears even during the silence period.
Troubleshoot CAM Profiling The following section describes CAM profiling troubleshooting. QoS CAM Region Limitation To store QoS service policies, the default CAM profile allocates a partition within the IPv4Flow region. If the QoS CAM space is exceeded, a message similar to the following displays.
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. That filter prevents traffic not specifically identified as legitimate from reaching the system control plane, rate-limits, traffic to an acceptable level.
Figure 28. CoPP Implemented Versus CoPP Not Implemented Topics: • Configure Control Plane Policing Configure Control Plane Policing The system can process a maximum of 4200 packets per second (PPS). Protocols that share a single queue may experience flaps if one of the protocols receives a high rate of control traffic even though per protocol CoPP is applied. This happens because queue-based rate limiting is applied first.
Configuring CoPP for Protocols This section lists the commands necessary to create and enable the service-policies for CoPP. For complete information about creating ACLs and QoS rules, refer to Access Control Lists (ACLs) and Quality of Service (QoS). The basics for creating a CoPP service policy are to create a Layer 2, Layer 3, and/or an IPv6 ACL rule for the desired protocol type. Then, create a QoS input policy to rate-limit the protocol traffics according to the ACL.
DellEMC(conf)#mac access-list extended lacp cpu-qos DellEMC(conf-mac-acl-cpuqos)#permit lacp DellEMC(conf-mac-acl-cpuqos)#exit DellEMC(conf)#ipv6 access-list ipv6-icmp cpu-qos DellEMC(conf-ipv6-acl-cpuqos)#permit icmp DellEMC(conf-ipv6-acl-cpuqos)#exit DellEMC(conf)#ipv6 access-list ipv6-vrrp cpu-qos DellEMC(conf-ipv6-acl-cpuqos)#permit vrrp DellEMC(conf-ipv6-acl-cpuqos)#exit The following example shows creating the QoS input policy.
1. Create a QoS input policy for the router and assign the policing. CONFIGURATION mode qos-policy-input name cpu-qos 2. Create an input policy-map to assign the QoS policy to the desired service queues.l. CONFIGURATION mode policy-map--input name cpu-qos service-queue queue-number qos-policy name 3. Enter Control Plane mode. CONFIGURATION mode control-plane-cpuqos 4. Assign a CPU queue-based service policy on the control plane in cpu-qos mode.
CPU Processing of CoPP Traffic The systems use FP rules to take the packets to control plane by CopyToCPU or redirect packet to CPU port. Only 8 CPU queues are used while sending the packet to CPU. The CPU Management Interface Controller (CMIC) interface on all the systems supports 48 queues in hardware.
NDP Packets Neighbor discovery protocol has 4 types of packets NS, NA, RA, RS. These packets need to be taken to CPU for neighbor discovery. ● Unicast NDP packets: ○ Packets hitting the L3 host/route table and discovered as local terminated packets/CPU bound traffic. For CPU bound traffic route entry have CPU action. Below are packets are CPU bound traffic. ￭ Packets destined to chassis.
Catch-All Entry for IPv6 Packets Dell EMC Networking OS currently supports configuration of IPv6 subnets greater than /64 mask length, but the agent writes it to the default LPM table where the key length is 64 bits. The device supports table to store up to 256 subnets of maximum of /128 mask lengths. This can be enabled and agent can be modified to update the /128 table for mask lengths greater than /64. This will restrict the subnet sizes to required optimal level which would avoid these NDP attacks.
Displaying CoPP Configuration The CLI provides show commands to display the protocol traffic assigned to each control-plane queue and the current rate-limit applied to each queue. Other show commands display statistical information for trouble shooting CoPP operation. To view the rates for each queue, use the show cpu-queue rate cp command.
Example of Viewing Queue Mapping for IPv6 Protocols DellEMC#show ipv6 protocol-queue-mapping Protocol Src-Port Dst-Port TcpFlag Queue EgPort Rate (kbps) --------------- -------- ------- ----- ------ ----------TCP (BGP) any/179 179/any _ Q6 CP _ ICMP any any _ Q6 CP _ VRRP any any _ Q7 CP _ DellEMC# Control Plane Policing (CoPP) 253
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of enhancements to Ethernet local area networks used in data center environments, particularly with clustering and storage area networks.
Data center bridging satisfies the needs of the following types of data center traffic in a unified fabric: Traffic Description LAN traffic LAN traffic consists of many flows that are insensitive to latency requirements, while certain applications, such as streaming video, are more sensitive to latency. Ethernet functions as a best-effort network that may drop packets in the case of network congestion.
The system supports loading two DCB_Config files: ● FCoE converged traffic with priority 3. ● iSCSI storage traffic with priority 4. In the Dell EMC Networking OS, PFC is implemented as follows: ● PFC is supported on specified 802.1p priority traffic (dot1p 0 to 7) and is configured per interface. However, only two lossless queues are supported on an interface: one for Fibre Channel over Ethernet (FCoE) converged traffic and one for Internet Small Computer System Interface (iSCSI) storage traffic.
Table 16. ETS Traffic Groupings (continued) Traffic Groupings Description Group ID A 4-bit identifier assigned to each priority group. The range is from 0 to 7 configurable; 8 - 14 reservation and 15.0 - 15.7 is strict priority group.. Group bandwidth Percentage of available bandwidth allocated to a priority group. Group transmission selection algorithm (TSA) Type of queue scheduling a priority group uses. In Dell EMC Networking OS, ETS is implemented as follows: ● ETS supports groups of 802.
Enabling Data Center Bridging DCB is automatically configured when you configure FCoE or iSCSI optimization. Data center bridging supports converged enhanced Ethernet (CEE) in a data center network. DCB is disabled by default. It must be enabled to support CEE. ● Priority-based flow control ● Enhanced transmission selection ● Data center bridging exchange protocol ● FCoE initialization protocol (FIP) snooping DCB processes virtual local area network (VLAN)-tagged packets and dot1p priority values.
Important Points to Remember ● If you remove a dot1p priority-to-priority group mapping from a DCB map (no priority pgid command), the PFC and ETS parameters revert to their default values on the interfaces on which the DCB map is applied. By default, PFC is not applied on specific 802.1p priorities; ETS assigns equal bandwidth to each 802.1p priority. As a result, PFC and lossless port queues are disabled on 802.
Set the bandwidth in percentage. The percentage range is from 1 to 100% in units of 1%. Committed and peak bandwidth is in megabits per second. The range is from 0 to 40000. Committed and peak burst size is in kilobytes. Default is 50. The range is from 0 to 40000. The pfc on command enables priority-based flow control. 3. Specify the dot1p priority-to-priority group mapping for each priority. priority-pgid dot1p0_group_num dot1p1_group_num ...dot1p7_group_num Priority group range is from 0 to 7.
2. Configure the port queues that will still function as no-drop queues for lossless traffic. INTERFACE mode pfc no-drop queues queue-range For the dot1p-queue assignments, refer to the dot1p Priority-Queue Assignment table. The maximum number of lossless queues globally supported on the switch is two. The range is from 0 to 7. Separate the queue values with a comma; specify a priority range with a dash; for example, pfc no-drop queues 1,7 or pfc no-drop queues 2-7. The range is from 0 to 3.
● For PFC to be applied, the configured priority traffic must be supported by a PFC peer (as detected by DCBx). ● If you apply a DCB map with PFC disabled (pfc off), you can enable link-level flow control on the interface using the flowcontrol rx on tx on command. To delete the DCB map, first disable link-level flow control. PFC is then automatically enabled on the interface because an interface is PFC-enabled by default.
Table 17. DCB Map to an Ethernet Port (continued) Step Task Command Command Mode priority command or which is already configured for lossless queues (pfc no-drop queues command). Configuring PFC without a DCB Map In a network topology that uses the default ETS bandwidth allocation (assigns equal bandwidth to each priority), you can also enable PFC for specific dot1p-priorities on individual interfaces without using a DCB map.
Refer the following configuration for queue to dot1p mapping: DellEMC(conf)#do show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 7 -> On ingress interfaces[Port A and C] we used the PFC on priority level. Queue : 0 0 0 1 2 3 3 3 -> On Egress interface[Port B] we used no-drop queues. Lossless traffic egresses out the no-drop queues. Ingress 802.1p traffic from PFC-enabled peers is automatically mapped to the no-drop egress queues.
Pause and Resume of Traffic The pause message is used by the sending device to inform the receiving device about a congested, heavily-loaded traffic state that has been identified. When the interface of a sending device transmits a pause frame, the recipient acknowledges this frame by temporarily halting the transmission of data packets. The sending device requests the recipient to restart the transmission of data traffic when the congestion eases and reduces.
● As the PG6 watermark threshold is reached, PFC generates for dot1p 2. Configuration Example for DSCP and PFC Priorities Consider a scenario in which the following DSCP and PFC priorities are necessary: DSCP 0 – 5, 10 - 15 Expected PFC Priority 1 20 – 25, 30 – 35 2 To configure the aforementioned DSCP and PFC priority values, perform the following tasks: 1.
Table 20. Queue Assignments (continued) Internal-priority Queue 7 7 3. Dot1p->Queue Mapping Configuration is retained at the default value. Default dot1p-queue mapping is, DellEMC#show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 Queue : 0 0 0 1 2 3 3 7 3 Default dot1p-queue mapping is, DellEMC#show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 Queue : 2 0 1 3 4 5 6 7 7 4. Interface Configurations on server connected ports. a. Enable DCB globally. DellEMC(conf)#dcb enable b.
Creating an ETS Priority Group An ETS priority group specifies the range of 802.1p priority traffic to which a QoS output policy with ETS settings is applied on an egress interface. 1. Configure a DCB Map. CONFIGURATION mode dcb-map dcb-map-name The dcb-map-name variable can have a maximum of 32 characters. 2. Create an ETS priority group. CONFIGURATION mode priority-group group-num {bandwidth bandwidth | strict-priority} pfc off The range for priority group is from 0 to 7. Set the bandwidth in percentage.
● ● ● ● ETS TLVs are supported in DCBx versions CIN, CEE, and IEEE2.5. The DCBx port-role configurations determine the ETS operational parameters (refer to Configure a DCBx Operation). ETS configurations received from TLVs from a peer are validated. If there is a hardware limitation or TLV error: ○ DCBx operation on an ETS port goes down. ○ New ETS configurations are ignored and existing ETS configurations are reset to the default ETS settings.
Configuring ETS in a DCB Map A switch supports the use of a DCB map in which you configure enhanced transmission selection (ETS) setting. To configure ETS parameters, you must apply a DCB map on an interface. ETS Configuration Notes ETS provides a way to optimize bandwidth allocation to outbound 802.1p classes of converged Ethernet traffic. Different traffic types have different service needs. Using ETS, you can create groups within an 802.
Priority-Group Configuration Notes When you configure priority groups in a DCB map: ● A priority group consists of 802.1p priority values that are grouped together for similar bandwidth allocation and scheduling, and that share the same latency and loss requirements. All 802.1p priorities mapped to the same queue must be in the same priority group. ● In a DCB map, each 802.1p priority must map to a priority group.
Configure a DCBx Operation DCB devices use data center bridging exchange protocol (DCBx) to exchange configuration information with directly connected peers using the link layer discovery protocol (LLDP) protocol. DCBx can detect the misconfiguration of a peer DCB device, and optionally, configure peer DCB devices with DCB feature settings to ensure consistent operation in a data center network.
When an auto-downstream port receives and overwrites its configuration with internally propagated information, one of the following actions is taken: ● If the peer configuration received is compatible with the internally propagated port configuration, the link with the DCBx peer is enabled. ● If the received peer configuration is not compatible with the currently configured port configuration, the link with the DCBx peer port is disabled and a syslog message for an incompatible configuration is generated.
Symmetric DCB parameters are exchanged between a DCBx-enabled port and a peer port but requires that each configured parameter value be the same for the configurations in order to be compatible. For example, PFC uses an symmetric exchange of parameters between DCBx peers. Configuration Source Election When an auto-upstream or auto-downstream port receives a DCB configuration from a peer, the port first checks to see if there is an active configuration source on the switch.
the peer version is recorded in the peer status table. If the frame cannot be processed, it is discarded and the discard counter is incremented. NOTE: Because DCBx TLV processing is best effort, it is possible that CIN frames may be processed when DCBx is configured to operate in CEE mode and vice versa. In this case, the unrecognized TLVs cause the unrecognized TLV counter to increment, but the frame is processed and is not discarded.
1. 2. 3. 4. Configure Configure Configure Configure ToR- and FCF-facing interfaces as auto-upstream ports. server-facing interfaces as auto-downstream ports. a port to operate in a configuration-source role. ports to operate in a manual role. 1. Enter INTERFACE Configuration mode. CONFIGURATION mode interface type slot/port[/subport] 2. Enter LLDP Configuration mode to enable DCBx operation. INTERFACE mode [no] protocol lldp 3.
For information about how to use iSCSI, refer to iSCSI Optimization To verify the DCBx configuration on a port, use the show interface DCBx detail command. Configuring DCBx Globally on the Switch To globally configure the DCBx operation on a switch, follow these steps. 1. Enter Global Configuration mode. EXEC PRIVILEGE mode configure 2. Enter LLDP Configuration mode to enable DCBx operation. CONFIGURATION mode [no] protocol lldp 3.
[no] iscsi priority-bits priority-bitmap The priority-bitmap range is from 1 to FF. The default is 0x10. DCBx Error Messages The following syslog messages appear when an error in DCBx operation occurs. LLDP_MULTIPLE_PEER_DETECTED: DCBx is operationally disabled after detecting more than one DCBx peer on the port interface. LLDP_PEER_AGE_OUT: DCBx is disabled as a result of LLDP timing out on a DCBx peer interface.
Verifying the DCB Configuration To display DCB configurations, use the following show commands. Table 21. Displaying DCB Configurations Command Output show qos dot1p-queue mapping Displays the current 802.1p priority-queue mapping. show dcb [stack-unit unit-number] Displays the data center bridging status, number of PFCenabled ports, and number of PFC-enabled queues. On the master switch in a stack, you can specify a stack-unit number. The range is from 0 to 5.
The following example shows the output of the show qos dcb-map test command. DellEMC#show qos dcb-map test ----------------------State :Complete PfcMode:ON -------------------PG:0 TSA:ETS BW:50 PFC:OFF Priorities:0 1 2 5 6 7 PG:1 TSA:ETS BW:50 Priorities:3 4 PFC:ON The following example shows the show interfaces pfc summary command.
Table 22. show interface pfc summary Command Description (continued) Fields Description are enabled to be sent and received from peers; received PFC configuration takes effect. The admin operational status for a DCBx exchange of PFC configuration is enabled or disabled. Remote is enabled; Priority list Remote Willing Status is enabled Operational status (enabled or disabled) of peer device for DCBx exchange of PFC configuration with a list of the configured PFC priorities.
The following example shows the show interface pfc statistics command. DellEMC#show interfaces te 1/1 pfc statistics Interface TenGigabitEthernet 1/1 Interface Priority Rx XOFF Frames Rx Total Frames Tx Total Frames ---------------------------------------------------------------------------------------------Te 1/1 P0 0 0 0 Te 1/1 P1 0 0 0 Te 1/1 P2 0 0 0 Te 1/1 P3 0 0 0 Te 1/1 P4 0 0 0 Te 1/1 P5 0 0 0 Te 1/1 P6 0 0 0 Te 1/1 P7 0 0 0 The following example shows the show interface ets summary command.
The following example shows the show interface ets detail command.
Table 23. show interface ets detail Command Description (continued) Field Description Number of Traffic Classes Number of 802.1p priorities currently configured. Admin mode ETS mode: on or off. Admin Parameters ETS configuration on local port, including priority groups, assigned dot1p priorities, and bandwidth allocation.
Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 Stack unit 1 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 DellEMC(c
5 6 7 8 - - The following example shows the show interface DCBx detail command (IEEE).
Table 24. show interface DCBx detail Command Description Field Description Interface Interface type with chassis slot and port number. Port-Role Configured DCBx port role: auto-upstream, auto-downstream, config-source, or manual. DCBx Operational Status Operational status (enabled or disabled) used to elect a configuration source and internally propagate a DCB configuration. The DCBx operational status is the combination of PFC and ETS operational status.
Honor dot1p You can honor dot1p priorities in ingress traffic at the port or global switch level (refer to Default dot1p to Queue Mapping) using the service-class dynamic dot1p command in INTERFACE configuration mode. Layer 2 class maps You can use dot1p priorities to classify traffic in a class map and apply a service policy to an ingress port to map traffic to egress queues. NOTE: Dell EMC Networking does not recommend mapping all ingress traffic to a single queue when using PFC and ETS.
dcb enable 2. Configure the shared PFC buffer size and the total buffer size. A maximum of 4 lossless queues are supported. CONFIGURATION mode dcb pfc-shared-buffer-size value dcb pfc-total-buffer-size value The buffer size range is from 0 to 3399. Default is 3088. 3. Configure the number of PFC queues. CONFIGURATION mode dcb enable pfc-queues pfc-queues The number of ports supported based on lossless queues configured depends on the buffer. The default number of PFC queues in the system is two.
Figure 33. PFC and ETS Applied to LAN, IPC, and SAN Priority Traffic QoS Traffic Classification: The service-class dynamic dot1p command has been used in Global Configuration mode to map ingress dot1p frames to the queues shown in the following table. For more information, refer to QoS dot1p Traffic Classification and Queue Assignment.
The following describes the priority group-bandwidth assignment. Priority Group Bandwidth Assignment IPC 5% SAN 50% LAN 45% PFC and ETS Configuration Command Examples The following examples show PFC and ETS configuration commands to manage your data center traffic. 1. Enabling DCB DellEMC(conf)#dcb enable 2. Configure DCB map and enable PFC, and ETS DellEMC(conf)# service-class dynamic dot1p Or DellEMC(conf)# interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)# service-class dynamic dot1p 3.
13 Dynamic Host Configuration Protocol (DHCP) DHCP is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on configuration policies determined by network administrators.
The following table lists common DHCP options. Option Number and Description Subnet Mask Option 1 Specifies the client’s subnet mask. Router Option 3 Specifies the router IP addresses that may serve as the client’s default gateway. Domain Name Server Option 6 Domain Name Option 15 Specifies the domain name servers (DNSs) that are available to the client. Specifies the domain name that clients should use when resolving hostnames via DNS.
Assign an IP Address using DHCP The following section describes DHCP and the client in a network. When a client joins a network: 1. The client initially broadcasts a DHCPDISCOVER message on the subnet to discover available DHCP servers. This message includes the parameters that the client requires and might include suggested values for those parameters. 2. Servers unicast or broadcast a DHCPOFFER message in response to the DHCPDISCOVER that offers to the client values for the requested parameters.
example, if all pools were configured for a /24 mask, the total would be 40000/253 (approximately 158). If the subnet is increased, more pools can be configured. The maximum subnet that can be configured for a single pool is /17. Dell EMC Networking OS displays an error message for configurations that exceed the allocated memory. ● This platform supports 4000 DHCP Snooping entries. ● All platforms support Dynamic ARP Inspection on 16 VLANs per system. For more information, refer to Dynamic ARP Inspection.
● prefix-length: specifies the number of bits used for the network portion of the address you specify. The prefix-length range is from 17 to 31. 4. Display the current pool configuration. DHCP mode show config After an IP address is leased to a client, only that client may release the address. Dell EMC Networking OS performs a IP + MAC source address validation to ensure that no client can release another clients address.
Configure a Method of Hostname Resolution Dell systems are capable of providing DHCP clients with parameters for two methods of hostname resolution—using DNS or NetBIOS WINS. Using DNS for Address Resolution A domain is a group of networks. DHCP clients query DNS IP servers when they need to correlate host names to IP addresses. 1. Create a domain. DHCP domain-name name 2. Specify in order of preference the DNS servers that are available to a DHCP client.
Debugging the DHCP Server To debug the DHCP server, use the following command. ● Display debug information for DHCP server. EXEC Privilege mode debug ip dhcp server [events | packets] Using DHCP Clear Commands To clear DHCP binding entries, address conflicts, and server counters, use the following commands. ● Clear DHCP binding entries for the entire binding table. EXEC Privilege mode. clear ip dhcp binding ● Clear a DHCP binding entry for an individual IP address. EXEC Privilege mode.
Figure 36. Configuring a Relay Agent To view the ip helper-address configuration for an interface, use the show ip interface command from EXEC privilege mode. Example of the show ip interface Command R1_E600#show ip int tengigabitethernet 1/3 TenGigabitEthernet 1/3 is up, line protocol is down Internet address is 10.11.0.1/24 Broadcast address is 10.11.0.255 Address determined by user input IP MTU is 1500 bytes Helper address is 192.168.0.1 192.168.0.
Configure the System to be a DHCP Client A DHCP client is a network device that requests an IP address and configuration parameters from a DHCP server. Implement the DHCP client functionality as follows: ● The switch can obtain a dynamically assigned IP address from a DHCP server. A start-up configuration is not received. Use bare metal provisioning (BMP) to receive configuration parameters (Dell EMC Networking OS version and a configuration file). BMP is enabled as a factory-default setting on a switch.
To renew the lease time of the dynamically acquired IP, use the renew dhcp command on an interface already configured with a dynamic IP address. NOTE: To verify the currently configured dynamic IP address on an interface, use the show ip dhcp lease command. The show running-configuration command output only displays ip address dhcp. The currently assigned dynamic IP address does not display. To configure and view an interface as a DHCP client to receive an IP address, use the following commands. 1.
● Management routes added by the DHCP client are not added to the running configuration. NOTE: Management routes added by the DHCP client include the specific routes to reach a DHCP server in a different subnet and the management route. DHCP Client Operation with Other Features The DHCP client operates with other Dell EMC Networking OS features, as the following describes. Stacking The DHCP client daemon runs only on the master unit and handles all DHCP packet transactions.
DHCP Relay When DHCP Server and Client are in Different VRFs When the DHCP server and DHCP clients belong to different VRFs on the relay agent, you can configure the system to leak routes across VRFs. You can configure the system to leak the following routes across VRFs: ● Connected routes ● The complete routing table ● Selective routes The following illustration depicts the topology in which routes are leaked between VRFs in the relay agent.
ip vrf VRF_2 ip route-import 2:2 ip route-export 1:1 ! ! route-map map1 permit 10 match ip address ip1 ! route-map map2 permit 20 match ip address ip2 ! ip prefix-list ip1 seq 5 permit 20.0.0.0/24 <----- This is needed for data forwarding seq 10 permit 20.0.0.2/32 <---- This is specific to internal operation of DHCP relay ! ip prefix-list ip2 seq 5 permit 10.0.0.
Dell(conf-if-lo-1)# ipv6 address 1::1/128 Dell(conf-if-lo-1)# no shutdown To configure the loopback interface as IPv4 or IPv6 DHCP relay source interface, enter the following commands in the CONFIGURATION MODE.
Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# Dell(conf-if-vl-4)# ip vrf forwarding vrf1 ip address 4.0.0.1/24 ipv6 address 4::1/64 tagged fortyGigE 0/4 ip helper-address vrf vrf1 100.0.0.1 ipv6 helper-address vrf vrf1 100::1 ip dhcp relay source-interface loopback 3 ipv6 dhcp relay source-interface loopback 3 3. In the below configuration, the DHCP relay source interface is not configured in the VLAN interface.
● Default Agent Remote ID is the system MAC address (in binary format). The following example shows the format of the Circuit ID - 723:0:1:1. Table 26. Circuit ID Format VLAN ID LAG ID Slot ID Port Str 723 0 1 1 The DHCP relay agent inserts Option 82 before forwarding DHCP packets to the server. The server can use this information to: ● Track the number of address requests per relay agent.
The relay agent checks all subsequent DHCP client-originated IP traffic (DHCPRELEASE, DHCPNACK, and DHCPDECLINE) against the binding table to ensure that the MAC-IP address pair is legitimate and that the packet arrived on the correct port. Packets that do not pass this check are forwarded to the server for validation. This checkpoint prevents an attacker from spoofing a client and declining or releasing the real client’s address.
Enabling IPv6 DHCP Snooping To enable IPv6 DHCP snooping, use the following commands. 1. Enable IPv6 DHCP snooping globally. CONFIGURATION mode ipv6 dhcp snooping 2. Specify ports connected to IPv6 DHCP servers as trusted. INTERFACE mode ipv6 dhcp snooping trust 3. Enable IPv6 DHCP snooping on a VLAN or range of VLANs. CONFIGURATION mode ipv6 dhcp snooping vlan vlan-id Adding a Static Entry in the Binding Table To add a static entry in the binding table, use the following command.
Displaying the Contents of the Binding Table To display the contents of the binding table, use the following command. ● Display the DHCP snooping information. EXEC Privilege mode show ip dhcp snooping ● Display the contents of the binding table. EXEC Privilege mode show ip dhcp snooping binding View the DHCP snooping statistics with the show ip dhcp snooping command.
10.1.1.11 10.1.1.25 00:00:a0:00:00:00 00:00:a0:00:00:00 39736 162 S D Vl 200 Vl 200 Po 10 Po 10 The following example shows a sample output of the show ip dhcp snooping binding command for a device connected to one of the VLT peers only (orphaned). The physical interface is the one that is directly connected to the VLT peer.
Drop DHCP Packets on Snooped VLANs Only Binding table entries are deleted when a lease expires or the relay agent encounters a DHCPRELEASE. Line cards maintain a list of snooped VLANs. When the binding table fills, DHCP packets are dropped only on snooped VLANs, while such packets are forwarded across non-snooped VLANs. Because DHCP packets are dropped, no new IP address assignments are made. However, DHCP release and decline packets are allowed so that the DHCP snooping table can decrease in size.
arp inspection To view entries in the ARP database, use the show arp inspection database command. DellEMC#show arp inspection database Protocol Address Age(min) Hardware Address Interface VLAN CPU --------------------------------------------------------------------Internet 10.1.1.251 00:00:4d:57:f2:50 Te 1/2 Vl 10 CP Internet 10.1.1.252 00:00:4d:57:e6:f6 Te 1/1 Vl 10 CP Internet 10.1.1.253 00:00:4d:57:f8:e8 Te 1/3 Vl 10 CP Internet 10.1.1.
arp inspection-trust Dynamic ARP inspection is supported on Layer 2 and Layer 3. Source Address Validation Using the DHCP binding table, Dell EMC Networking OS can perform three types of source address validation (SAV). Table 27. Three Types of Source Address Validation Source Address Validation Description IP Source Address Validation Prevents IP spoofing by forwarding only IP packets that have been validated against the DHCP binding table.
● Enable DHCP MAC SAV. CONFIGURATION mode ip dhcp snooping verify mac-address Enabling IP+MAC Source Address Validation IP source address validation (SAV) validates the IP source address of an incoming packet and optionally the VLAN ID of the client against the DHCP snooping binding table. IP+MAC SAV ensures that the IP source address and MAC source address are a legitimate pair, rather than validating each attribute individually. You cannot configure IP+MAC SAV with IP SAV. 1.
Clearing the Number of SAV Dropped Packets To clear the number of SAV dropped packets, use the clear ip dhcp snooping source-address-validation discard-counters command. DellEMC>clear ip dhcp snooping source-address-validation discard-counters To clear the number of SAV dropped packets on a particular interface, use the clear ip dhcp snooping sourceaddress-validation discard-counters interface interface command.
14 Equal Cost Multi-Path (ECMP) This chapter describes configuring ECMP. This chapter describes configuring ECMP. Topics: • • • • ECMP for Flow-Based Affinity Link Bundle Monitoring RTAG7 Flow-based Hashing for ECMP ECMP for Flow-Based Affinity ECMP for flow-based affinity includes link bundle monitoring.
Configuring the Hash Algorithm Seed Deterministic ECMP sorts ECMPs in order even though RTM provides them in a random order. However, the hash algorithm uses as a seed the lower 12 bits of the chassis MAC, which yields a different hash result for every chassis. This behavior means that for a given flow, even though the prefixes are sorted, two unrelated chassis can select different hops.
Managing ECMP Group Paths To avoid path degeneration, configure the maximum number of paths for an ECMP route that the L3 CAM can hold. When you do not configure the maximum number of routes, the CAM can hold a maximum ECMP per route. To configure the maximum number of paths, use the following command. NOTE: For the new settings to take effect, save the new ECMP settings to the startup-config (write-mem) then reload the system. ● Configure the maximum number of paths per ECMP group. CONFIGURATION mode.
NOTE: An ecmp-group index is generated automatically for each unique ecmp-group when you configure multipath routes to the same network. The system can generate a maximum of 512 unique ecmp-groups. The ecmp-group indices are generated in even numbers (0, 2, 4, 6... 1022) and are for information only. You can configure ecmp-group with id 2 for link bundle monitoring. This ecmp-group is different from the ecmp-group index 2 that is created by configuring routes and is automatically generated.
mac Set the mac key fields to use in hash computation(default = source-mac dest-mac vlan ethertype) tcp-udp Option to use TCP/UDP ports in packet for ECMP/LAG hashing tunnel Set the tunnel key fields to use in hash computation(default = Hash-computation based on Inner Header)] ● The second portion comes from static physical configuration such as ingress and egress port numbers.
Figure 37. Before Polarization Effect Router B performs the same hash as router A and all the traffic goes through the same path to router D, while no traffic is redirected to router E. Some of the anti-polarization techniques used generally to mitigate unequal traffic distribution in LAG/ECMP as follows: 1. Configuring different hash-seed values at each node - Hash seed is the primary parameter in hash computations that determine distribution of traffic among the ECMP paths.
bits of xor4 xor8 bits of xor8 xor16 CRC16_BISYNC_AND_XOR8 - Upper 8 bits of CRC16-BISYNC and lower 8 CR16 - 16 bit XOR] Example to view show hash-algorithm: DellEMC(conf)#hash-algorithm ecmp flow-based-hashing crc16 DellEMC(conf)#end DellEMC#show hash-algorithm Hash-Algorithm linecard 0 Port-Set 0 Seed 185270328 Hg-Seed 185282673 EcmpFlowBasedHashingAlgo- crc16 EcmpAlgo- crc32MSB LagAlgo- crc32LSB HgAlgo- crc16 Figure 38.
15 FIP Snooping The Fibre Channel over Ethernet (FCoE) Transit feature is supported on Ethernet interfaces. When you enable the switch for FCoE transit, the switch functions as a FIP snooping bridge. NOTE: FIP snooping is not supported on Fibre Channel interfaces or in a switch stack.
The following table lists the FIP functions. Table 28. FIP Functions FIP Function Description FIP VLAN discovery FCoE devices (ENodes) discover the FCoE VLANs on which to transmit and receive FIP and FCoE traffic. FIP discovery FCoE end-devices and FCFs are automatically discovered. Initialization FCoE devices learn ENodes from the FLOGI and FDISC to allow immediate login and create a virtual link with an FCoE switch.
Dynamic ACL generation on the switch operating as a FIP snooping bridge function as follows: Port-based ACLs These ACLs are applied on all three port modes: on ports directly connected to an FCF, server-facing ENode ports, and bridge-to-bridge links. Port-based ACLs take precedence over global ACLs. FCoE-generated ACLs These take precedence over user-configured ACLs. A user-configured ACL entry cannot deny FCoE and FIP snooping frames.
● To provide more port security on ports that are directly connected to an FCF and have links to other FIP snooping bridges, set the FCF or Bridge-to-Bridge Port modes. ● To ensure that they are operationally active, check FIP snooping-enabled VLANs. ● Process FIP VLAN discovery requests and responses, advertisements, solicitations, FLOGI/FDISC requests and responses, FLOGO requests and responses, keep-alive packets, and clear virtual-link messages.
● When you disable FIP snooping: ○ ACLs are not installed, FIP and FCoE traffic is not blocked, and FIP packets are not processed. ○ The existing per-VLAN and FIP snooping configuration is stored. The configuration is re-applied the next time you enable the FIP snooping feature. ● You must apply the CAM-ACL space for the FCoE region before enabling the FIP-Snooping feature.
● FCoE traffic is allowed on VLANs only after a successful virtual-link initialization (fabric login FLOGI) between an ENode and an FCF. All other FCoE traffic is dropped. ● You must configure at least one interface for FCF (FCoE Forwarder) mode on a FIP snooping-enabled VLAN. You can configure multiple FCF trusted interfaces in a VLAN. ● A maximum of eight VLANS are supported for FIP snooping on the switch.
Table 29. Impact of Enabling FIP Snooping (continued) Impact Description deleted. If a port is enabled for FIP snooping in ENode or FCF mode, the ENode/FCF MAC-based ACLs are deleted. FIP Snooping Restrictions The following restrictions apply when you configure FIP snooping. ● The maximum number of FCoE VLANs supported on the switch is eight. ● The maximum number of FIP snooping sessions supported per ENode server is 32.
Displaying FIP Snooping Information Use the following show commands to display information on FIP snooping. Table 30. Displaying FIP Snooping Information Command Output show fip-snooping sessions [interface vlan vlan-id] Displays information on FIP-snooped sessions on all VLANs or a specified VLAN, including the ENode interface and MAC address, the FCF interface and MAC address, VLAN ID, FCoE MAC address and FCoE session ID number (FC-ID), worldwide node name (WWNN) and the worldwide port name (WWPN).
Table 31. show fip-snooping sessions Command Description Field Description ENode MAC MAC address of the ENode . ENode Interface Slot/port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. FCF Interface Slot/port number of the interface to which the FCF is connected. VLAN VLAN ID number used by the session. FCoE MAC MAC address of the FCoE session assigned by the FCF. FC-ID Fibre Channel ID assigned by the FCF. Port WWPN Worldwide port name of the CNA port.
Table 33. show fip-snooping fcf Command Description (continued) Field Description FCF Interface Slot/port number of the interface to which the FCF is connected. VLAN VLAN ID number used by the session. FC-MAP FC-Map value advertised by the FCF. ENode Interface Slot/port number of the interface connected to the ENode. FKA_ADV_PERIOD Period of time (in milliseconds) during which FIP keep-alive advertisements are transmitted. No of ENodes Number of ENodes connected to the FCF.
The following example shows the show fip-snooping statistics port-channel command.
Table 34. show fip-snooping statistics Command Descriptions (continued) Field Description Number of FDISC Rejects Number of FIP FDISC reject frames received on the interface. Number of FLOGO Accepts Number of FIP FLOGO accept frames received on the interface. Number of FLOGO Rejects Number of FIP FLOGO reject frames received on the interface. Number of CVLs Number of FIP clear virtual link frames received on the interface.
FCoE Transit Configuration Example The following illustration shows a switch used as a FIP snooping bridge for FCoE traffic between an ENode (server blade) and an FCF (ToR switch). The ToR switch operates as an FCF and FCoE gateway. Figure 41. Configuration Example: FIP Snooping on a Switch In this example, DCBx and PFC are enabled on the FIP snooping bridge and on the FCF ToR switch.
Example of Configuring the ENode Server-Facing Port DellEMC(conf)# interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)# portmode hybrid DellEMC(conf-if-te-1/1)# switchport DellEMC(conf-if-te-1/1)# protocol lldp DellEMC(conf-if-te-1/1-lldp)# dcbx port-role auto-downstream NOTE: A port is enabled by default for bridge-ENode links.
16 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Topics: • • • • • • • Flex Hash Capability Overview Configuring the Flex Hash Mechanism Configuring Fast Boot and LACP Fast Switchover Optimizing the Boot Time Interoperation of Applications with Fast Boot and System States RDMA Over Converged Ethernet (RoCE) Overview Preserving 802.
Flex hash APIs do not mask out unwanted byte values after extraction of the data from the Layer 4 headers for the offset value. 2. Use the load-balance flexhash command to specify whether IPv4 or IPv6 packets must be subjected to the flex hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name.
unexpected shutdown) from an older release of Dell EMC Networking OS to Release 9.3(0.0) or later. Dell EMC recommends that you do not downgrade your system from Release 9.3(0.0) to an earlier release that does not support the fast boot functionality because the system behavior is unexpected and undefined. ● Fast boot uses the Symmetric Multiprocessing (SMP) utility that is enabled on the Intel CPU on the device to enhance the speed of the system startup. SMP is supported on the device.
A file is generated to indicate that the system is undergoing a fast boot, which is used after the system comes up. After the Dell EMC Networking OS image is loaded and activated, and the appropriate software components come up, the following additional actions are performed: ● If a database of dynamic ARP entries is present on the flash drive, that information is read and the ARP entries are restored; the entries are installed on the switch as soon as possible.
Unexpected Reload of the System When an unexpected or unplanned reload occurs, such as a reset caused by the software, the system performs the regular boot sequence even if it is configured for fast boot. When the system comes up, dynamic ARP or ND database entries are not present or required to be restored. The system boot up mode will not be fast boot and actions specific to this mode will not be performed.
RDMA Over Converged Ethernet (RoCE) Overview This functionality is supported on the platform. RDMA is a technology that a virtual machine (VM) uses to directly transfer information to the memory of another VM, thus enabling VMs to be connected to storage networks. With RoCE, RDMA enables data to be forwarded without passing through the CPU and the main memory path of TCP/IP.
except the Layer 2 and Layer 3 control frames. It is not required for a VLAN ID to be preserved (in the hardware or the OS application) when a VLAN ID, used for encapsulation, is associated with a physical/Port-channel interface. Normal VLANs and VLAN encapsulation can exist simultaneously and any non-unicast traffic received on a normal VLAN is not flooded using lite subinterfaces whose encapsulation VLAN ID matches with that of the normal VLAN ID.
17 FIPS Cryptography Federal information processing standard (FIPS) cryptography provides cryptographic algorithms conforming to various FIPS standards published by the National Institute of Standards and Technology (NIST), a non-regulatory agency of the US Department of Commerce. FIPS mode is also validated for numerous platforms to meet the FIPS-140-2 standard for a softwarebased cryptographic module. This chapter describes how to enable FIPS cryptography requirements on Dell EMC Networking platforms.
When you enable FIPS mode, the following actions are taken: ● If enabled, the SSH server is disabled. ● All open SSH and Telnet sessions, as well as all SCP and FTP file transfers, are closed. ● Any existing host keys (both RSA and RSA1) are deleted from system memory and NVRAM storage. ● FIPS mode is enabled. ○ If you enable the SSH server when you enter the fips mode enable command, it is re-enabled for version 2 only. ○ If you re-enable the SSH server, a new RSA host key-pair is generated automatically.
● ● ● ● ● Any existing host keys (both RSA and RSA1) are deleted from system memory and NVRAM storage. FIPS mode disables. The SSH server re-enables. The Telnet server re-enables (if it is present in the configuration). New 1024–bit RSA and RSA1 host key-pairs are created. To disable FIPS mode, use the following command. ● To disable FIPS mode from a console port.
18 Force10 Resilient Ring Protocol (FRRP) FRRP provides fast network convergence to Layer 2 switches interconnected in a ring topology, such as a metropolitan area network (MAN) or large campuses. FRRP is similar to what can be achieved with the spanning tree protocol (STP), though even with optimizations, STP can take up to 50 seconds to converge (depending on the size of network and node of failure) and may require 4 to 5 seconds to reconverge.
Ring Status The ring failure notification and the ring status checks provide two ways to ensure the ring remains up and active in the event of a switch or port failure. Ring Checking At specified intervals, the Master node sends a ring health frame (RHF) through the ring. If the ring is complete, the frame is received on its secondary port and the Master node resets its fail-period timer and continues normal operation.
Figure 42. Example of Multiple Rings Connected by Single Switch Important FRRP Points FRRP provides a convergence time that can generally range between 150ms and 1500ms for Layer 2 networks. The Master node originates a high-speed frame that circulates around the ring. This frame, appropriately, sets up or breaks down the ring. ● The Master node transmits ring status check frames at specified intervals. ● You can run multiple physical rings on the same switch.
Important FRRP Concepts The following table lists some important FRRP concepts. Concept Explanation Ring ID Each ring has a unique 8-bit ring ID through which the ring is identified (for example, FRRP 101 and FRRP 202, as shown in the illustration in Member VLAN Spanning Two Rings Connected by One Switch. Control VLAN Each ring has a unique Control VLAN through which tagged ring health frames (RHF) are sent. Control VLANs are used only for sending RHF, and cannot be used for any other purpose.
● If multiple rings share one or more member VLANs, they cannot share any links between them. ● Member VLANs across multiple rings are not supported in Master nodes. ● Each ring has only one Master node; all others are transit nodes. FRRP Configuration These are the tasks to configure FRRP.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 3. Assign the Primary and Secondary ports and the control VLAN for the ports on the ring. CONFIG-FRRP mode.
VLAN ID: Identification number of the Control VLAN. 4. Configure a Transit node. CONFIG-FRRP mode. mode transit 5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id {range} VLAN-ID, Range: VLAN IDs for the ring’s Member VLANs. 6. Enable this FRRP group on this switch. CONFIG-FRRP mode. no disable Setting the FRRP Timers To set the FRRP timers, use the following command. NOTE: Set the Dead-Interval time 3 times the Hello-Interval.
Ring ID: the range is from 1 to 255. ● Show the state of all FRRP groups. EXEC or EXEC PRIVELEGED mode. show frrp summary Ring ID: the range is from 1 to 255. Troubleshooting FRRP To troubleshoot FRRP, use the following information. Configuration Checks ● ● ● ● ● Each Control Ring must use a unique VLAN ID. Only two interfaces on a switch can be Members of the same control VLAN. There can be only one Master node for any FRRP group. You can configure FRRP on Layer 2 interfaces only.
! interface TenGigabitEthernet 2/31 no ip address switchport no shutdown ! interface Vlan 101 no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! interface Vlan 201 no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! protocol frrp 101 interface primary TenGigabitEthernet 2/14 secondary TenGigabitEthernet 2/31 controlvlan 101 member-vlan 201 mode transit no disable Example of R3 TRANSIT interface TenGigabitEthernet 3/14 no ip address switchport no shutdown ! interface TenGigabitEthernet 3
Figure 43. FRRP Ring Connecting VLT Devices You can also configure an FRRP ring where both the VLT peers are connected to the FRRP ring and the VLTi acts as the primary interface for the FRRP Master and transit nodes. This active-active FRRP configuration blocks the FRRP ring on a per VLAN or VLAN group basis enabling the configuration to spawn across different set of VLANs.
control VLAN, multiple member VLANS are configured (for example, M1 to M10) that carry the data traffic across the FRRP rings. The secondary port P2 is tagged to the control VLAN (V1). VLTi is implicitly tagged to the member VLANs when these VLANs are configured in the VLT peer. As a result of the VLT Node2 configuration on R2, the secondary interface P2 is blocked for the member VLANs (M11 to Mn). Following figure illustrated the FRRP Ring R1 topology: Figure 44.
19 GARP VLAN Registration Protocol (GVRP) The generic attribute registration protocol (GARP) VLAN registration protocol (GVRP), defined by the IEEE 802.1q specification, is a Layer 2 network protocol that provides for automatic VLAN configuration of switches. GVRP-compliant switches use GARP to register and de-register attribute values, such as VLAN IDs, with each other.
Configure GVRP To begin, enable GVRP. To facilitate GVRP communications, enable GVRP globally on each switch. Then, GVRP configuration is per interface on a switch-by-switch basis. Enable GVRP on each port that connects to a switch where you want GVRP information exchanged. In the following example, GVRP is configured on VLAN trunk ports. Figure 45. Global GVRP Configuration Example Basic GVRP configuration is a two-step process: 1. Enabling GVRP Globally 2.
gvrp enable DellEMC(conf)#protocol gvrp DellEMC(config-gvrp)#no disable DellEMC(config-gvrp)#show config ! protocol gvrp no disable DellEMC(config-gvrp)# To inspect the global configuration, use the show gvrp brief command. Enabling GVRP on a Layer 2 Interface To enable GVRP on a Layer 2 interface, use the following command. ● Enable GVRP on a Layer 2 interface.
no shutdown DellEMC(conf-if-te-1/21)# Configure a GARP Timer Set GARP timers to the same values on all devices that are exchanging information using GVRP. There are three GARP timer settings. ● Join — A GARP device reliably transmits Join messages to other devices by sending each Join message two times. To define the interval between the two sending operations of each Join message, use this parameter. The Dell EMC Networking OS default is 200ms.
20 High Availability (HA) High availability (HA) is supported on Dell EMC Networking OS. HA is a collection of features that preserves system continuity by maximizing uptime and minimizing packet loss during system disruptions. To support all the features within the HA collection, you should have the latest boot code. The following table lists the boot code requirements as of this Dell EMC Networking OS release. Table 35. Boot Code Requirements Component Boot Code S4048–ON 1 2.0.
Stack-unit State: Stack-unit SW Version: Link to Peer: Peer Stack-unit: Active 9.6(0.
Pre-Configuring a Stack Unit Slot You may also pre-configure an empty stack unit slot with a logical stack unit. To pre-configure an empty stack unit slot, use the following command. ● Pre-configure an empty stack unit slot with a logical stack unit. CONFIGURATION mode stack-unit unit_id provisionS4048–ON After creating the logical stack unit, you can configure the interfaces on the stack unit as if it is present.
Software Resiliency During normal operations, Dell EMC Networking OS monitors the health of both hardware and software components in the background to identify potential failures, even before these failures manifest. Software Component Health Monitoring On each of the line cards and the stack unit, there are a number of software components.
Hot-Lock Behavior Dell EMC Networking OS hot-lock features allow you to append and delete their corresponding content addressable memory (CAM) entries dynamically without disrupting traffic. Existing entries are simply shuffled to accommodate new entries. Hot-Lock IP ACLs allows you to append rules to and delete rules from an access control list (ACL) that is already written to CAM. This behavior is enabled by default and is available for both standard and extended ACLs on ingress and egress.
21 Internet Group Management Protocol (IGMP) Internet group management protocol (IGMP) is a Layer 3 multicast protocol that hosts use to join or leave a multicast group. Multicast is premised on identifying many hosts by a single destination IP address; hosts represented by the same IP address are a multicast group. Multicast routing protocols (such as protocol-independent multicast [PIM]) use the information in IGMP messages to discover which groups are active and to populate the multicast routing table.
Figure 46. IGMP Messages in IP Packets Join a Multicast Group There are two ways that a host may join a multicast group: it may respond to a general query from its querier or it may send an unsolicited report to its querier. Responding to an IGMP Query The following describes how a host can join a multicast group. 1. One router on a subnet is elected as the querier. The querier periodically multicasts (to all-multicast-systems address 224.0.0.1) a general query to all hosts on the subnet. 2.
IGMP Version 3 Conceptually, IGMP version 3 behaves the same as version 2. However, there are differences. ● Version 3 adds the ability to filter by multicast source, which helps multicast routing protocols avoid forwarding traffic to subnets where there are no interested receivers. ● To enable filtering, routers must keep track of more state information, that is, the list of sources that must be filtered.
Joining and Filtering Groups and Sources The following illustration shows how multicast routers maintain the group and source information from unsolicited reports. 1. The first unsolicited report from the host indicates that it wants to receive traffic for group 224.1.1.1. 2. The host’s second report indicates that it is only interested in traffic from group 224.1.1.1, source 10.11.1.1. Include messages prevents traffic from all other sources in the group from reaching the subnet.
Leaving and Staying in Groups The following illustration shows how multicast routers track and refresh state changes in response to group-and-specific and general queries. 1. Host 1 sends a message indicating it is leaving group 224.1.1.1 and that the included filter for 10.11.1.1 and 10.11.1.2 are no longer necessary. 2.
● ● ● ● ● ● Adjusting Timers Preventing a Host from Joining a Group Enabling IGMP Immediate-Leave IGMP Snooping Fast Convergence after MSTP Topology Changes Designating a Multicast Router Interface Viewing IGMP Enabled Interfaces Interfaces that are enabled with PIM-SM are automatically enabled with IGMP. To view IGMP-enabled interfaces, use the following command. ● View IGMP-enabled IPv4 interfaces. EXEC Privilege mode show ip igmp interface ● View IGMP-enabled IPv6 interfaces.
TenGigabitEthernet 1/13 is up, line protocol is down Inbound IGMP access group is not set Interface IGMP group join rate limit is not set Internet address is 1.1.1.1/24 IGMP is enabled on interface IGMP query interval is 60 seconds IGMP querier timeout is 125 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is disabled IGMP activity: 0 joins, 0 leaves, 0 channel joins, 0 channel leaves IGMP querying router is 1.1.1.
When the querier receives a leave message from a host, it sends a group-specific query to the subnet. If no response is received, it sends another. The amount of time that the querier waits to receive a response to the initial query before sending a second one is the last member query interval (LMQI). The switch waits one LMQI after the second query before removing the group from the state table. ● Adjust the period between queries.
Figure 51. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 36. Preventing a Host from Joining a Group — Description Location Description 1/21 ● ● ● ● Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 ● ● ● ● Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Table 36. Preventing a Host from Joining a Group — Description (continued) Location Description 2/11 ● ● ● ● Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 ● ● ● ● Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 ● ● ● ● Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 ● ● ● ● Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
IGMP Snooping IGMP snooping enables switches to use information in IGMP packets to generate a forwarding table that associates ports with multicast groups so that when they receive multicast frames, they can forward them only to interested receivers. Multicast packets are addressed with multicast MAC addresses, which represent a group of devices, rather than one unique device.
● View the configuration. INTERFACE VLAN mode show config DellEMC(conf-if-vl-100)#show config ! interface Vlan 100 no ip address ip igmp snooping fast-leave shutdown DellEMC(conf-if-vl-100)# Disabling Multicast Flooding If the switch receives a multicast packet that has an IP address of a group it has not learned (unregistered frame), the switch floods that packet out of all ports on the VLAN. When you configure the no ip igmp snooping flood command, the system drops the packets immediately.
Adjusting the Last Member Query Interval To adjust the last member query interval, use the following command. When the querier receives a Leave message from a receiver, it sends a group-specific query out of the ports specified in the forwarding table. If no response is received, it sends another. The amount of time that the querier waits to receive a response to the initial query before sending a second one is the last member query interval (LMQI).
Protocol Separation When you configure the application application-type command to configure a set of management applications with TCP/UDP port numbers to the OS, the following table describes the association between applications and their port numbers. Table 37.
● The CLI prompt changes to the EIS mode. ● In this mode, you can run the application and no application commands ● Applications can be configured or unconfigured as management applications using the application or no application command. All configured applications are considered as management applications and the rest of them as non-management applications. ● All the management routes (connected, static and default) are duplicated and added to the management EIS routing table.
Handling of Switch-Initiated Traffic When the control processor (CP) initiates a control packet, the following processing occurs: ● TCP/UDP port number is extracted from the sockaddr structure in the in_selectsrc call which is called as part of the connect system call or in the ip_output function.
● Rest of the response traffic is handled as per existing behavior by doing route lookup in the default routing table. So if the traffic is destined to the front-end port IP address, the response is sent out by doing a route lookup in the default routing table, which is an existing behavior. Consider a sample topology in which ip1 is an address assigned to the management port and ip2 is an address assigned to any of the front panel port. A and B are end users on the management and front-panel port networks.
● Drop the packets that are received on the front-end data port with destination on the management port. ● Drop the packets that received on the management port with destination as the front-end data port. Switch-Destined Traffic This phenomenon occurs where traffic is terminated on the switch. Traffic has not originated from the switch and is not transiting the switch. The switch accepts all traffic destined to the switch, which is received on management or front-end data port.
Table 39. Behavior of Various Applications for Switch-Initiated Traffic (continued) Protocol Behavior when EIS is Enabled Behavior when EIS is Disabled tftp EIS Behavior Default Behavior icmp (ping and traceroute) EIS Behavior for ICMP Default Behavior Behavior of Various Applications for Switch-Destined Traffic This section describes the different system behaviors that occur when traffic is terminated on the switch. Traffic has not originated from the switch and is not transiting the switch.
● If management EIS is enabled, this default route is added to the management EIS routing table and the default routing table. ARP learn enable ● When ARP learn enable is enabled, the switch learns ARP entries for ARP Request packets even if the packet is not destined to an IP configured in the box. ● The ARP learn enable feature is not applicable to the EIS routing table.
22 Interfaces This chapter describes interface types, both physical and logical, and how to configure them with Dell EMC Networking Operating System (OS). The system supports 10 Gigabit Ethernet and 40 Gigabit Ethernet interfaces. NOTE: Only Dell-qualified optics are supported on these interfaces. Non-Dell 40G optics are set to error-disabled state.
• • • • • • • • • • • • • • • • • • Bulk Configuration Defining Interface Range Macros Monitoring and Maintaining Interfaces Non Dell-Qualified Transceivers Splitting 40G Ports without Reload Splitting QSFP Ports to SFP+ Ports Converting a QSFP or QSFP+ Port to an SFP or SFP+ Port Configuring wavelength for 10–Gigabit SFP+ optics Link Dampening Link Bundle Monitoring Using Ethernet Pause Frames for Flow Control Configure the MTU Size on an Interface Port-Pipes Auto-Negotiation on Ethernet Interfaces View A
NOTE: The CLI output may be incorrectly displayed as 0 (zero) for the Rx/Tx power values. To obtain the correct power information, perform a simple network management protocol (SNMP) query. The following example shows the configuration and status information for one interface.
interface TenGigabitEthernet 2/8 no ip address shutdown ! interface TenGigabitEthernet 2/9 no ip address shutdown Resetting an Interface to its Factory Default State You can reset the configurations applied on an interface to its factory default state. To reset the configuration, perform the following steps: 1. View the configurations applied on an interface.
no shutdown To confirm that the interface is enabled, use the show config command in INTERFACE mode. To leave INTERFACE mode, use the exit command or end command. You cannot delete a physical interface. Physical Interfaces The Management Ethernet interface is a single RJ-45 Fast Ethernet port on a switch. The interface provides dedicated management access to the system. Stack-unit interfaces support Layer 2 and Layer 3 traffic over the and 40-Gigabit Ethernet interfaces.
Configuring Layer 2 (Data Link) Mode Do not configure switching or Layer 2 protocols such as spanning tree protocol (STP) on an interface unless the interface has been set to Layer 2 mode. To set Layer 2 data transmissions through an individual interface, use the following command. ● Enable Layer 2 data transmissions through an individual interface.
To determine the configuration of an interface, use the show config command in INTERFACE mode or the various show interface commands in EXEC mode. Configuring Layer 3 (Interface) Mode To assign an IP address, use the following commands. ● Enable the interface. INTERFACE mode no shutdown ● Configure a primary IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] The ip-address must be in dotted-decimal format (A.B.C.D) and the mask must be in slash format (/xx).
No minor alarms Major Alarms Port 2 in unit 1 high internal temperature 1 min, 33 sec NOTE: This feature is not supported for stacking ports. To change the optical port from reset to normal mode, you must execute the enable stack-unit unit-number port port-number transceiver command. Example of the show command outputs To view if this feature is enabled or disable, use the show interface interface-name transceiver command.
Wavelength is 0nm Interface index is 2097284 Internet address is not set Mode of IPv4 Address Assignment : NONE DHCP Client-ID :f48e38068718 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto Flowcontrol rx off tx off ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 02:05:20 Queueing strategy: fifo Enabling temperature polling on ports To enable temperature polling on the ports, use the following command.
● FEFD ● MAC learning limit ● ARP inspection Based on the automatic recovery configuration, when the interface is changed to Err-disabled state, the Dell EMC Networking OS invokes a timer for the configured time-out interval. Upon expiration of the timer, the interface is moved to operationally up state if the encountered error is fixed. If not, the interface is again moved to Err-disabled state again.
Egress Interface Selection (EIS) EIS allows you to isolate the management and front-end port domains by preventing switch-initiated traffic routing between the two domains. This feature provides additional security by preventing flooding attacks on front-end ports. The following protocols support EIS: DNS, FTP, NTP, RADIUS, sFlow, SNMP, SSH, Syslog, TACACS, Telnet, and TFTP. This feature does not support sFlow on stacked units.
The port range is 1. ● Configure an IP address and mask on a Management interface. INTERFACE mode ip address ip-address mask ○ ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in /prefix format (/x). You can configure two global IPv6 addresses on the system in EXEC Privilege mode. To view the addresses, use the show interface managementethernet command, as shown in the following example. If you try to configure a third IPv6 address, an error message displays.
Configuring a Management Interface on an Ethernet Port You can manage the system through any port using remote access such as Telnet. To configure an IP address for the port, use the following commands. There is no separate management routing table, so configure all routes in the IP routing table (the ip route command). ● Configure an IP address. INTERFACE mode ip address ip-address mask ● Enable the interface. INTERFACE mode no shutdown ● The interface is the management interface.
NOTE: You cannot assign an IP address to the default VLAN, which is VLAN 1 (by default). To assign another VLAN ID to the default VLAN, use the default vlan-id vlan-id command. To assign an IP address to an interface, use the following command. ● Configure an IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] ○ ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in slash format (/24).
Configuring Port Delay To configure a delayed bring up of all interfaces during switch boot up, use the following command: ● Enter the CONFIGURATION mode. CONFIGURATION mode Use the port-delay-restore command and ensure to specify a value between 1 second and 300 seconds. DellEMC(conf)#port-delay-restore 300 Use the no port-delay-restore command to disable the feature.
● Dynamic — Port channels that are dynamically configured using the link aggregation control protocol (LACP). For details, see Link Aggregation Control Protocol (LACP). The port channel ID ranges from 1 to 128. Although the system allows you to assign more number of ports in a port channel, Dell EMC Networking recommends having a maximum of 16 interfaces per port channel. As soon as you configure a port channel, Dell EMC Networking OS treats it like a physical interface. For example, IEEE 802.
Creating a Port Channel You can create up to 128 port channels with up to 16 port members per group on the platform. To configure a port channel, use the following commands. 1. Create a port channel. CONFIGURATION mode interface port-channel id-number 2. Ensure that the port channel is active. INTERFACE PORT-CHANNEL mode no shutdown After you enable the port channel, you can place it in Layer 2 or Layer 3 mode.
DellEMC# Te 1/8 (Up) Te 1/13 (Up) Te 1/14 (Up) The following example shows the port channel’s mode (L2 for Layer 2 and L3 for Layer 3 and L2L3 for a Layer 2-port channel assigned to a routed VLAN), the status, and the number of interfaces belonging to the port channel. DellEMC>show interface port-channel 20 Port-channel 20 is up, line protocol is up Hardware address is 00:01:e8:01:46:fa Internet address is 1.1.120.
no channel-member interface 2. Change to the second port channel INTERFACE mode. INTERFACE PORT-CHANNEL mode interface port-channel id number 3. Add the interface to the second port channel. INTERFACE PORT-CHANNEL mode channel-member interface The following example shows moving an interface from port channel 4 to port channel 3.
An interface without tagging enabled can belong to only one VLAN. ● Remove the port channel with tagging enabled from the VLAN. INTERFACE VLAN mode no tagged port-channel id number or no untagged port-channel id number ● Identify which port channels are members of VLANs. EXEC Privilege mode show vlan Configuring VLAN Tags for Member Interfaces To configure and verify VLAN tags for individual members of a port channel, perform the following: 1.
● Delete a port channel. CONFIGURATION mode no interface portchannel channel-number ● Disable a port channel. shutdown When you disable a port channel, all interfaces within the port channel are operationally down also. Load Balancing Through Port Channels Dell EMC Networking OS uses hash algorithms for distributing traffic evenly over channel members in a port channel (LAG). The hash algorithm distributes traffic among Equal Cost Multi-path (ECMP) paths and LAG members.
Bulk Configuration Bulk configuration allows you to determine if interfaces are present for physical interfaces or configured for logical interfaces. Interface Range An interface range is a set of interfaces to which other commands may be applied and may be created if there is at least one valid interface within the range. Bulk configuration excludes from configuration any non-existing interfaces from an interface range.
Create a Multiple-Range The following is an example of multiple range. Example of the interface range Command (Multiple Ranges) DellEMC(conf)#interface range tengigabitethernet 1/5 - 1/10 , tengigabitethernet 1/1 , vlan 1 DellEMC(conf-if-range-te-1/1,te-1/5-1/10,vl-1)# Exclude Duplicate Entries The following is an example showing how duplicate entries are omitted from the interface-range prompt.
Add Ranges The following example shows how to use commas to add VLAN and port-channel interfaces to the range. Example of Adding VLAN and Port-Channel Interface Ranges DellEMC(config-if-range-te-1/1-1/2)# interface range Vlan 2 – 100 , Port 1 – 25 DellEMC(config-if-range-te-1/1-1/2-vl-2-100-po-1-25)# no shutdown Defining Interface Range Macros You can define an interface-range macro to automatically select a range of interfaces for configuration.
○ For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ○ For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. The information displays in a continuous run, refreshing every 2 seconds by default. To manage the output, use the following keys.
1. To test for cable faults on the TenGigabitEthernet cable. EXEC Privilege mode tdr-cable-test tengigabitethernet slot/port[/subport] Between two ports, do not start the test on both ends of the cable. Enable the interface before starting the test. Enable the port to run the test or the test prints an error message. 2. Displays TDR test results.
show system stack-unit stack-unit number fanout configured Example of the show Command The following example shows the show system stack-unit stack-unit number fanout configured command.
----------------------------------------------------------------------------------1 49/1 QSFP 4x10GBASE-CR1-3M CN027GG536409H3 Yes 1 49/2 QSFP 4x10GBASE-CR1-3M CN027GG536409H3 Yes 1 49/3 QSFP 4x10GBASE-CR1-3M CN027GG536409H3 Yes 1 49/4 QSFP 4x10GBASE-CR1-3M CN027GG536409H3 Yes Splitting QSFP Ports to SFP+ Ports The platform supports splitting a single 40G QSFP port into four 10G SFP+ ports using one of the supported breakout cables (for a list of supported cables, refer to the Installation Guide or the Rel
10 Gigabit port and you can use only that port for data transfer. As a result, only the first fanned-out port is identified as the active 10 Gigabit port with a speed of 10G or 1G depending on whether you insert an SFP+ or SFP cable respectively. NOTE: Although it is possible to configure the remaining three 10 Gigabit ports, the Link UP event does not occur for these ports leaving the lanes unusable. Dell Networking OS perceives these ports to be in a Link Down state.
SFP+ 1 Connector ………………………. = 0x23 Dell#show interfaces tengigabitethernet 1/2 transceiver SFP+ 1 Serial ID Base Fields SFP+ 1 Id = 0x0d SFP+ 1 Ext Id = 0x00 SFP+ 1 Connector = 0x23 ………………………. Dell#show interfaces tengigabitethernet 1/3 transceiver SFP+ 1 Serial ID Base Fields SFP+ 1 Id = 0x0d SFP+ 1 Ext Id = 0x00 SFP+ 1 Connector = 0x23 ……………………….
You configure link dampening using the dampening [[[[half-life] [reuse-threshold]] [suppressthreshold]] [max-suppress-time]] command on the interface. Following is the detailed explanation of interface state change events: ● suppress-threshold— The suppress threshold is a value that triggers a flapping interface to dampen. The system adds penalty when the interface state goes up and down.
Figure 52. Interface State Change Consider an interface periodically flaps as shown above. Every time the interface goes down, a penalty (1024) is added. In the above example, during the first interface flap (flap 1), the penalty is added to 1024. And, the accumulated penalty will exponentially decay based on the set half-life, which is set as 10 seconds in the above example. During the second interface flap (flap 2), again the penalty (1024) is accumulated.
Enabling Link Dampening To enable link dampening, use the following command. ● Enable link dampening. INTERFACE mode dampening To view the link dampening configuration on an interface, use the show config command. R1(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 ip address 10.10.19.1/24 dampening 1 2 3 4 no shutdown To view dampening information on all or specific dampened interfaces, use the show interfaces dampening command from EXEC Privilege mode.
Configure MTU Size on an Interface In Dell EMC Networking OS, Maximum Transmission Unit (MTU) is defined as the entire Ethernet packet (Ethernet header + FCS + payload). The following table lists the range for each transmission media. Transmission Media MTU Range (in bytes) Ethernet 592-9216 = link MTU 576-9398 = IP MTU The IP MTU automatically configures.
The globally assigned 48-bit Multicast address 01-80-C2-00-00-01 is used to send and receive pause frames. To allow fullduplex flow control, stations implementing the pause operation instruct the MAC to enable reception of frames with destination address equal to this multicast address. The PAUSE frame is defined by IEEE 802.3x and uses MAC Control frames to carry the PAUSE commands. Ethernet pause frames are supported on full duplex only.
1400-byte IP MTU + 22-byte VLAN Tag = 1422-byte link MTU The following table lists the various Layer 2 overheads found in Dell EMC Networking OS and the number of bytes. The MTU range is from 592 to 9216, with a default of 9216. IP MTU automatically configures. The following table lists the various Layer 2 overheads found in the Dell EMC Networking OS and the number of bytes. Table 43.
Setting the speed to 10/100/1000 Mbps on SFP-1G-T transceiver Dell EMC Networking OS allows you to disable the auto-negotiation on the SFP-1G-T transceiver connected interface and set the speed manually to 10/100/1000 Mbps. You can disable the auto-negotiation using no negotiation auto command and enable setting the interface speed using the speed command at the INTERFACE mode.
Te 1/12 Down [output omitted] Auto Auto -- In the previous example, several ports display “Auto” in the Speed field. In the following example, the speed of port 1/1 is set to 100Mb and then its auto-negotiation is disabled.
View Advanced Interface Information The following options have been implemented for the show [ip | running-config] interfaces commands for (only) stack-unit interfaces. When you use the configured keyword, only interfaces that have non-default configurations are displayed. Dummy stack-unit interfaces (created with the stack-unit command) are treated like any other physical interface.
Hardware is DellEMCEth, address is 00:01:e8:01:9e:d9 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 10000 Mbit ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1d23h44m Queueing strategy: fifo 0 packets input, 0 bytes Input 0 IP Packets, 0 Vlans 0 MPLS 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Chec
The bold lines shows the default value of 299 seconds, the change-rate interval of 100, and the new rate interval set to 100.
Output 100.00 Mbits/sec, 4636111 packets/sec, 10.00% of line-rate Time since last interface status change: 21:00:43 Dynamic Counters By default, counting is enabled for IPFLOW, IPACL, L2ACL, L2FIB. For the remaining applications, Dell EMC Networking OS automatically turns on counting when you enable the application, and is turned off when you disable the application. NOTE: If you enable more than four counter-dependent applications on a port pipe, there is an impact on line rate performance.
Discard Counters The Dell Networking OS discard counters counts the packets or frames which are legitimate but dropped due to lack of operation of the higher layer protocol. The discard counters do not count the errors such as runts, giants, throttles, CRC, overrun, underrun, symbol error, etc. For example, when an OSPF packet is received on a switch which has OSPF disabled, the packet gets dropped due to filter processor (FP) entry and the discard counter gets incremented.
2. 3. 4. 5. ● VLT PE ECP PDUs ● VLT IPM1 sync frames ● VLT ARP sync frames ● VLT TTL1 packets tunneled ● VLT ARP replies tunneled ● VLT STP BPDUs tunneled ● FEFD ● VRRP frames redirects ● ARP reply packets ● GVRP traffic redirects ● LACP traffic redirects ● Common VLT control frames Packets are dropped due to user defined ACLs. Multicast traffic with the TTL value 1. Multicast traffic is not part of any group or special group that has to be processed by the CPU.
23 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for protecting IP communications by authenticating and encrypting all packets in a communication session. Use IPSec between hosts, between gateways, or between hosts and gateways. IPSec is compatible with Telnet and FTP protocols. It supports two operational modes: Transport and Tunnel. ● Transport mode — (default) Use to encrypt only the payload of the packet. Routing information is unchanged.
match 0 tcp a::1 /128 0 a::2 /128 23 match 1 tcp a::1 /128 23 a::2 /128 0 match 2 tcp a::1 /128 0 a::2 /128 21 match 3 tcp a::1 /128 21 a::2 /128 0 match 4 tcp 1.1.1.1 /32 0 1.1.1.2 /32 23 match 5 tcp 1.1.1.1 /32 23 1.1.1.2 /32 0 match 6 tcp 1.1.1.1 /32 0 1.1.1.2 /32 21 match 7 tcp 1.1.1.1 /32 21 1.1.1.2 /32 0 3. Apply the crypto policy to management traffic.
24 IPv4 Routing The Dell EMC Networking Operating System (OS) supports various IP addressing features. This chapter describes the basics of domain name service (DNS), address resolution protocol (ARP), and routing principles and their implementation in the Dell EMC Networking OS.
IP Addresses Dell EMC Networking OS supports IP version 4 (as described in RFC 791), classful routing, and variable length subnet masks (VLSM). With VLSM, you can configure one network with different masks. Supernetting, which increases the number of subnets, is also supported. To subnet, you add a mask to the IP address to separate the network and host portions of the IP address.
INTERFACE mode ip address ip-address mask [secondary] ● ip-address mask: the IP address must be in dotted decimal format (A.B.C.D). The mask must be in slash prefixlength format (/24). ● secondary: add the keyword secondary if the IP address is the interface’s backup IP address. You can configure up to eight secondary IP addresses. To view the configuration, use the show config command in INTERFACE mode or use the show ip interface command in EXEC privilege mode, as shown in the second example.
S 6.1.2.9/32 S 6.1.2.10/32 S 6.1.2.11/32 S 6.1.2.12/32 S 6.1.2.13/32 S 6.1.2.14/32 S 6.1.2.15/32 S 6.1.2.16/32 S 6.1.2.17/32 S 11.1.1.0/24 Direct, Lo 0 --More-- via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.
Configure Static Routes for the Management Interface When an IP address that a protocol uses and a static management route exists for the same prefix, the protocol route takes precedence over the static management route. To configure a static route for the management port, use the following command. ● Assign a static route to point to the management interface or forwarding router.
Using the Configured Source IP Address in ICMP Messages ICMP error or unreachable messages are now sent with the configured IP address of the source interface instead of the front-end port IP address as the source IP address. Enable the generation of ICMP unreachable messages through the ip unreachable command in Interface mode. When a ping or traceroute packet from an endpoint or a device arrives at the null 0 interface configured with a static route, it is discarded.
INTERFACE mode ip directed-broadcast To view the configuration, use the show config command in INTERFACE mode. Resolution of Host Names Domain name service (DNS) maps host names to IP addresses. This feature simplifies commands such as Telnet and FTP by allowing you to enter a name instead of an IP address. Dynamic resolution of host names is disabled by default. Unless you enable the feature, the system resolves only host names entered into the host table with the ip host command.
Specifying the Local System Domain and a List of Domains If you enter a partial domain, Dell EMC Networking OS can search different domains to finish or fully qualify that partial domain. A fully qualified domain name (FQDN) is any name that is terminated with a period/dot. Dell EMC Networking OS searches the host table first to resolve the partial domain. The host table contains both statically configured and dynamically learnt host and IP addresses.
ARP Dell EMC Networking OS uses two forms of address resolution: address resolution protocol (ARP) and Proxy ARP. ARP runs over Ethernet and enables endstations to learn the MAC addresses of neighbors on an IP network. Over time, Dell EMC Networking OS creates a forwarding table mapping the MAC addresses to their corresponding IP address. This table is called the ARP Cache and dynamically learned addresses are removed after a defined period of time.
Enabling Proxy ARP By default, Proxy ARP is enabled. To disable Proxy ARP, use the no proxy-arp command in the interface mode. To re-enable Proxy ARP, use the following command. ● Re-enable Proxy ARP. INTERFACE mode ip proxy-arp To view if Proxy ARP is enabled on the interface, use the show config command in INTERFACE mode. If it is not listed in the show config command output, it is enabled. Only non-default information is displayed in the show config command output.
ARP Learning via ARP Request In Dell EMC Networking OS versions prior to 8.3.1.0, Dell EMC Networking OS learns via ARP requests only if the target IP specified in the packet matches the IP address of the receiving router interface. This is the case when a host is attempting to resolve the gateway address. If the target IP does not match the incoming interface, the packet is dropped. If there is an existing entry for the requesting host, it is updated. Figure 53.
The default is 5. The range is from 1 to 20. ● Set the exponential timer for resending unresolved ARPs. CONFIGURATION mode arp backoff-time The default is 30. The range is from 1 to 3600. ● Display all ARP entries learned via gratuitous ARP. EXEC Privilege mode show arp retries ICMP For diagnostics, the internet control message protocol (ICMP) provides routing information to end stations by choosing the best route (ICMP redirect messages) or determining if a router is reachable (ICMP Echo or Echo Reply).
Figure 55. ICMP Redirect Host H is connected to the same Ethernet segment as SW1 and SW2. SW1 and SW2 are multi-layer switches which can route packets. The default gateway of Host H is configured as SW1. Although the best route to the remote branch office host may be through SW2, Host H sends a packet destined for Host R to its default gateway — SW1.
○ UDP broadcast traffic with port number 67 or 68 are unicast to the dynamic host configuration protocol (DHCP) server per the ip helper-address configuration whether or not the UDP port list contains those ports. ○ If the UDP port list contains ports 67 or 68, UDP broadcast traffic is forwarded on those ports. Enabling UDP Helper To enable UDP helper, use the following command. ● Enable UPD helper.
Figure 56. UDP Helper with Broadcast-All Addresses UDP Helper with Subnet Broadcast Addresses When the destination IP address of an incoming packet matches the subnet broadcast address of any interface, the system changes the address to the configured broadcast address and sends it to matching interface. In the following illustration, Packet 1 has the destination IP address 1.1.1.255, which matches the subnet broadcast address of VLAN 101.
Figure 58. UDP Helper with Configured Broadcast Addresses UDP Helper with No Configured Broadcast Addresses The following describes UDP helper with no broadcast addresses configured. ● If the incoming packet has a broadcast destination IP address, the unaltered packet is routed to all Layer 3 interfaces. ● If the Incoming packet has a destination IP address that matches the subnet broadcast address of any interface, the unaltered packet is routed to the matching interfaces.
25 IPv6 Routing Internet protocol version 6 (IPv6) routing is the successor to IPv4. Due to the rapid growth in internet users and IP addresses, IPv4 is reaching its maximum usage. IPv6 will eventually replace IPv4 usage to allow for the constant expansion. This chapter provides a brief description of the differences between IPv4 and IPv6, and the Dell EMC Networking support of IPv6. This chapter is not intended to be a comprehensive description of IPv6.
● Duplicate Address Detection (DAD) — Before configuring its IPv6 address, an IPv6 host node device checks whether that address is used anywhere on the network using this mechanism. ● Prefix Renumbering — Useful in transparent renumbering of hosts in the network when an organization changes its service provider. NOTE: As an alternative to stateless autoconfiguration, network hosts can obtain their IPv6 addresses using the dynamic host control protocol (DHCP) servers via stateful auto-configuration.
Version (4 bits) The Version field always contains the number 6, referring to the packet’s IP version. Traffic Class (8 bits) The Traffic Class field deals with any data that needs special handling. These bits define the packet priority and are defined by the packet Source. Sending and forwarding routers use this field to identify different IPv6 classes and priorities. Routers understand the priority settings and handle them appropriately during conditions of congestion.
Hop Limit (8 bits) The Hop Limit field shows the number of hops remaining for packet processing. In IPv4, this is known as the Time to Live (TTL) field and uses seconds rather than hops. Each time the packet moves through a forwarding router, this field decrements by 1. If a router receives a packet with a Hop Limit of 1, it decrements it to 0 (zero). The router discards the packet and sends an ICMPv6 message back to the sending router indicating that the Hop Limit was exceeded in transit.
11 Discard the packet and send an ICMP Parameter Problem, Code 2 message to the packet’s Source IP Address only if the Destination IP Address is not a multicast address. The second byte contains the Option Data Length. The third byte specifies whether the information can change en route to the destination. The value is 1 if it can change; the value is 0 if it cannot change.
Implementing IPv6 with Dell EMC Networking OS Dell EMC Networking OS supports both IPv4 and IPv6 and both may be used simultaneously in your system. The following table lists the Dell EMC Networking OS version in which an IPv6 feature became available for each platform. The sections following the table give greater detail about the feature. Table 44.
Table 44. Dell EMC Networking OS versions and supported platforms with IPv6 support (continued) Feature and Functionality Dell EMC Networking OS Release Introduction Documentation and Chapter Location S4048–ON IPv6 IS-IS in the Dell EMC Networking OS Command Line Reference Guide. OSPF for IPv6 (OSPFv3) 9.7.(0.1) Equal Cost Multipath for IPv6 9.7.(0.1) OSPFv3 in the Dell EMC Networking OS Command Line Reference Guide. IPv6 Services and Management Telnet client over IPv6 (outbound Telnet) 9.7.(0.
Path MTU discovery The size of the packet that can be sent across each hop in the network path without being fragmented is called the path maximum transmission unit (PMTU). The PMTU value might differ for the same route between two devices, mainly over a public network, depending on the network load and speed, and it is not a consistent value. The MTU size can also be different for various types of traffic sent from one host to the same endpoint.
Figure 61. NDP Router Redirect IPv6 Neighbor Discovery of MTU Packets You can set the MTU advertised through the RA packets to incoming routers, without altering the actual MTU setting on the interface. The ipv6 nd mtu command sets the value advertised to routers. It does not set the actual MTU rate. For example, if you set ipv6 nd mtu to 1280, the interface still passes 1500-byte packets, if that is what is set with the mtu command.
● invalid host addresses If you specify this information in the IPv6 RDNSS configuration, a DNS error is displayed. Example for Configuring an IPv6 Recursive DNS Server The following example configures a RDNNS server with an IPv6 address of 1000::1 and a lifetime of 1 second.
ff02::1 ff02::2 ff02::1:ff00:12 ff02::1:ff8b:7570 ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20120 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 ND dns-server ad
You must enter the ipv6acl allocation as a factor of 2 (2, 4, 6, 8, 10). All other profile allocations can use either even or odd-numbered ranges. The default option sets the CAM Profile as follows: ● L3 ACL (ipv4acl): 6 ● L2 ACL(l2acl): 5 ● IPv6 L3 ACL (ipv6acl): 0 ● L3 QoS (ipv4qos): 1 ● L2 QoS (l2qos): 1 To have the changes take effect, save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings. ● Allocate space for IPV6 ACLs.
NOTE: After you configure a static IPv6 route (the ipv6 route command) and configure the forwarding router’s address (specified in the ipv6 route command) on a neighbor’s interface, the IPv6 neighbor does not display in the show ipv6 route command output. ● Set up IPv6 static routes. CONFIGURATION mode ipv6 route [vrf vrf-name] prefix interface-type slot/port [/subport] forwarding router tag ○ vrf vrf-name:(OPTIONAL) name of the VRF.
Displaying IPv6 Information View specific IPv6 configuration with the following commands. ● List the IPv6 show options.
ND ND ND ND reachable time is 32000 milliseconds base reachable time is 30000 milliseconds retransmit interval is 1000 milliseconds hop limit is 64 Showing IPv6 Routes To view the global IPv6 routing information, use the following command. ● Show IPv6 routing information for the specified route type. EXEC mode show ipv6 route [vrf vrf-name] type The following keywords are available: ○ To display information about a network, enter ipv6 address (X:X:X:X::X).
Direct, Nu 0, 00:34:42 DellEMC# The following example shows the show ipv6 route static command.
ipv6 nd disable-reachable-timer ● To reenable the ND timer, use the no form of the command: INTERFACE no ipv6 nd disable-reachable-timer The following example shows how to disable the ND timer. DellEMC(conf-if-fo-1/1/1)#ipv6 nd disable-reachable-timer Configuring IPv6 RA Guard The IPv6 Router Advertisement (RA) guard allows you to block or reject the unwanted router advertisement guard messages that arrive at the network device platform. To configure the IPv6 RA guard, perform the following steps: 1.
11. Apply the policy to trusted ports. POLICY LIST CONFIGURATION mode trusted-port 12. Set the maximum transmission unit (MTU) value. POLICY LIST CONFIGURATION mode mtu value 13. Set the advertised reachability time. POLICY LIST CONFIGURATION mode reachable—time value The reachability time range is from 0 to 3,600,000 milliseconds. 14. Set the advertised retransmission time. POLICY LIST CONFIGURATION mode retrans—timer value The retransmission time range is from 100 to 4,294,967,295 milliseconds. 15.
router-preference maximum medium trusted-port Interfaces : Te 1/1 DellEMC# Monitoring IPv6 RA Guard To debug IPv6 RA guard, use the following command. EXEC Privilege mode debug ipv6 nd ra-guard [interface slot/port[/subport] | count value] The count range is from 1 to 65534. The default is infinity. For a complete listing of all commands related to IPv6 RA Guard, see the Dell EMC Networking OS Command Line Reference Guide.
26 iSCSI Optimization This chapter describes how to configure internet small computer system interface (iSCSI) optimization, which enables qualityof-service (QoS) treatment for iSCSI traffic.
NOTE: After a switch is reloaded, powercycled, or upgraded, the system may display the ACL_AGENT-3ISCSI_OPT_MAX_SESS_LIMIT_REACHED: Monitored iSCSI sessions reached maximum limit log message. This cannot be inferred as the maximum supported iSCSI sessions are reached. Also, number of iSCSI sessions displayed on the system may show any number equal to or less than the maximum.
Application of Quality of Service to iSCSI Traffic Flows You can configure iSCSI CoS mode. This mode controls whether CoS (dot1p priority) queue assignment and/or packet marking is performed on iSCSI traffic. When you enable iSCSI CoS mode, the CoS policy is applied to iSCSI traffic. When you disable iSCSI CoS mode, iSCSI sessions and connections are still detected and displayed in the status tables, but no CoS policy is applied to iSCSI traffic.
Detection and Auto-Configuration for Dell EqualLogic Arrays The iSCSI optimization feature includes auto-provisioning support with the ability to detect directly connected Dell EqualLogic storage arrays and automatically reconfigure the switch to enhance storage traffic flows. The switch uses the link layer discovery protocol (LLDP) to discover Dell EqualLogic devices on the network. LLDP is enabled by default. For more information about LLDP, refer to Link Layer Discovery Protocol (LLDP).
● Additional updates to connections (including aging updates) that are learnt on VLT lag members are synced to the peer. ● When receiving an iSCSI login request on a non-VLT interface followed by a response from a VLT interface, the session is not synced since it is initially learnt on a non-VLT interface through the request packet. ● The peer generates a new connection log that sees the login response packet.
Table 45. iSCSI Optimization Defaults (continued) Parameter Default Value iSCSI optimization target ports iSCSI well-known ports 3260 and 860 are configured as default (with no IP address or name) but can be removed as any other configured target. iSCSI session monitoring Disabled. The CAM allocation for iSCSI is set to zero (0). iSCSI Optimization Prerequisites The following are iSCSI optimization prerequisites. ● iSCSI optimization requires LLDP on the switch.
[no] iscsi target port tcp-port-1 [tcp-port-2...tcp-port-16] [ip-address address] ● tcp-port-n is the TCP port number or a list of TCP port numbers on which the iSCSI target listens to requests. You can configure up to 16 target TCP ports on the switch in one command or multiple commands. The default is 860, 3260. Separate port numbers with a comma. If multiple IP addresses are mapped to a single TCP port, use the no iscsi target port tcp-port-n command to remove all IP addresses assigned to the TCP number.
Displaying iSCSI Optimization Information To display information on iSCSI optimization, use the following show commands. ● Display the currently configured iSCSI settings. show iscsi ● Display information on active iSCSI sessions on the switch. show iscsi sessions ● Display detailed information on active iSCSI sessions on the switch . To display detailed information on specified iSCSI session, enter the session’s iSCSI ID.
Up Time:00:00:01:28(DD:HH:MM:SS) Time for aging out:00:00:09:34(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target IP Address TCP Port IP Address TCPPort 10.10.0.53 33432 10.10.0.
27 Intermediate System to Intermediate System The intermediate system to intermediate system (IS-IS) protocol that uses a shortest-path-first algorithm. Dell EMC Networking supports both IPv4 and IPv6 versions of IS-IS.
Figure 63. ISO Address Format Multi-Topology IS-IS Multi-topology IS-IS (MT IS-IS) allows you to create multiple IS-IS topologies on a single router with separate databases. Use this feature to place a virtual physical topology into logical routing domains, which can each support different routing and security policies. All routers on a LAN or point-to-point must have at least one common supported topology when operating in Multi-Topology IS-IS mode.
Graceful Restart Graceful restart is a protocol-based mechanism that preserves the forwarding table of the restarting router and its neighbors for a specified period to minimize the loss of packets. A graceful-restart router does not immediately assume that a neighbor is permanently down and so does not trigger a topology change. Normally, when an IS-IS router is restarted, temporary disruption of routing occurs due to events in both the restarting router and the neighbors of the restarting router.
● Computes routes to IPv6 destinations. ● Downloads IPv6 routes to the RTM for installing in the FIB. ● Accepts external IPv6 information and advertises this information in the PDUs. The following table lists the default IS-IS values. Table 46.
In IS-IS, neighbors form adjacencies only when they are same IS type. For example, a Level 1 router never forms an adjacency with a Level 2 router. A Level 1-2 router forms Level 1 adjacencies with a neighboring Level 1 router and forms Level 2 adjacencies with a neighboring Level 2 router. NOTE: Even though you enable IS-IS globally, enable the IS-IS process on an interface for the IS-IS process to exchange protocol information and form adjacencies. To configure IS-IS globally, use the following commands.
To view the IS-IS configuration, enter the show isis protocol command in EXEC Privilege mode or the show config command in ROUTER ISIS mode. DellEMC#show isis protocol IS-IS Router: System Id: EEEE.EEEE.EEEE IS-Type: level-1-2 Manual area address(es): 47.0004.004d.0001 Routing for area address(es): 21.2223.2425.2627.2829.3031.3233 47.0004.004d.
ROUTER ISIS AF IPV6 mode set-overload-bit 3. Set the minimum interval between SPF calculations. ROUTER ISIS AF IPV6 mode spf-interval [level-l | level-2 | interval] [initial_wait_interval [second_wait_interval]] Use this command for IPv6 route computation only when you enable multi-topology. If using single-topology mode, to apply to both IPv4 and IPv6 route computations, use the spf-interval command in CONFIG ROUTER ISIS mode. 4. Implement a wide metric-style globally.
○ adjacency: the restarting router receives the remaining time value from its peer and adjusts its T3 value so if user has configured this option. ○ manual: allows you to specify a fixed value that the restarting router should use. The range is from 50 to 120 seconds. The default is 30 seconds. NOTE: If this timer expires before the synchronization has completed, the restarting router sends the overload bit in the LSP.
Changing LSP Attributes IS-IS routers flood link state PDUs (LSPs) to exchange routing information. LSP attributes include the generation interval, maximum transmission unit (MTU) or size, and the refresh interval. You can modify the LSP attribute defaults, but it is not necessary. To change the defaults, use any or all of the following commands. ● Set interval between LSP generation. ROUTER ISIS mode lsp-gen-interval [level-1 | level-2] seconds ○ seconds: the range is from 0 to 120.
Table 47. Metric Styles Metric Style Characteristics Cost Range Supported on IS-IS Interfaces narrow Sends and accepts narrow or old TLVs (Type, Length, Value). 0 to 63 wide Sends and accepts wide or new TLVs. 0 to 16777215 transition Sends both wide (new) and narrow (old) TLVs. 0 to 63 narrow transition Sends narrow (old) TLVs and accepts both narrow (old) and wide (new) TLVs. 0 to 63 wide transition Sends wide (new) TLVs and accepts both narrow (old) and wide (new) TLVs.
isis ipv6 metric default-metric [level-1 | level-2] ○ default-metric: the range is from 0 to 63 for narrow and transition metric styles. The range is from 0 to 16777215 for wide metric styles. The default is 10. The default level is level-1. For more information about this command, refer to Configuring the IS-IS Metric Style. The following table describes the correct value range for the isis metric command.
LSPID B233.00-00 eljefe.00-00 * eljefe.01-00 * eljefe.02-00 * Force10.00-00 LSP Seq Num 0x00000006 0x0000000D 0x00000001 0x00000001 0x00000004 LSP Checksum 0xC38A 0x51C6 0x68DF 0x2E7F 0xCDA9 LSP Holdtime 1124 1129 1122 1113 1107 ATT/P/OL 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 DellEMC# Controlling Routing Updates To control the source of IS-IS route information, use the following command. ● Disable a specific interface from sending or receiving IS-IS routing information.
○ ospf process-id: for OSPF routes only. ○ rip: for RIP routes only. ○ static: for user-configured routes. ○ bgp: for BGP routes only. ● Deny RTM download for pre-existing redistributed IPv4 routes. ROUTER ISIS mode distribute-list redistributed-override in Applying IPv6 Routes To apply prefix lists to incoming or outgoing IPv6 routes, use the following commands. NOTE: These commands apply to IPv6 IS-IS only. To apply prefix lists to IPv4 routes, use ROUTER ISIS mode, previously shown.
● Include BGP, directly connected, RIP, or user-configured (static) routes in IS-IS. ROUTER ISIS mode redistribute {bgp as-number | connected | rip | static} [level-1 level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] Configure the following parameters: ○ level-1, level-1-2, or level-2: assign all redistributed routes to a level. The default is level-2. ○ metric-value the range is from 0 to 16777215. The default is 0.
ISIS mode. To view the current IPv6 IS-IS configuration, use the show config command in ROUTER ISIS-ADDRESS FAMILY IPV6 mode. Configuring Authentication Passwords You can assign an authentication password for routers in Level 1 and for routers in Level 2. Because Level 1 and Level 2 routers do not communicate with each other, you can assign different passwords for Level 1 routers and for Level 2 routers.
Force10.00-00 DellEMC# 0x00000004 0xCDA9 1093 0/0/0 Debugging IS-IS To debug IS-IS processes, use the following commands. ● View all IS-IS information. EXEC Privilege mode debug isis ● View information on all adjacency-related activity (for example, hello packets that are sent and received).
● transition (supports both narrow and wide and uses a TLV up to 63) ● narrow transition (accepts both narrow and wide and sends only narrow or old-style TLV) ● wide transition (accepts both narrow and wide and sends only wide or new-style TLV) Configure Metric Values For any level (Level-1, Level-2, or Level-1-2), the value range possible in the isis metric command in INTERFACE mode changes depending on the metric style. The following describes the correct value range for the isis metric command.
Table 48.
Leaks from One Level to Another In the following scenarios, each IS-IS level is configured with a different metric style. Table 50.
● Congruent Topology — You must configure both IPv4 and IPv6 addresses on the interface. Enable the ip router isis and ipv6 router isis commands on the interface. Enable the wide-metrics parameter in router isis configuration mode. ● Multi-topology — You must configure the IPv6 address. Configuring the IPv4 address is optional. You must enable the ipv6 router isis command on the interface. If you configure IPv4, also enable the router isis command.
DellEMC(conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.00 ! address-family ipv6 unicast multi-topology exit-address-family DellEMC(conf-router_isis)# IS-IS Sample Configuration — Multi-topology Transition DellEMC(conf-if-te-3/17)#show config ! interface TenGigabitEthernet 3/17 ipv6 address 24:3::1/76 ipv6 router isis no shutdown DellEMC(conf-if-te-3/17)# DellEMC(conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.
28 Link Aggregation Control Protocol (LACP) A link aggregation group (LAG), referred to as a port channel by the Dell EMC Networking OS, can provide both load-sharing and port redundancy across line cards. You can enable LAGs as static or dynamic.
● You can configure link dampening on individual members of a LAG. LACP Modes Dell EMC Networking OS provides three modes for configuration of LACP — Off, Active, and Passive. ● Off — In this state, an interface is not capable of being part of a dynamic LAG. LACP does not run on any port that is configured to be in this state. ● Active — In this state, the interface is said to be in the “active negotiating state.” LACP runs on any link that is configured to be in this state.
Creating a LAG To create a dynamic port channel (LAG), use the following command. First you define the LAG and then the LAG interfaces. ● Create a dynamic port channel (LAG). CONFIGURATION mode interface port-channel ● Create a dynamic port channel (LAG). CONFIGURATION mode switchport DellEMC(conf)#interface port-channel 32 DellEMC(conf-if-po-32)#no shutdown DellEMC(conf-if-po-32)#switchport The LAG is in the default VLAN. To place the LAG into a non-default VLAN, use the tagged command on the LAG.
NOTE: The 30-second timeout is available for dynamic LAG interfaces only. You can enter the lacp long-timeout command for static LAGs, but it has no effect. To configure LACP long timeout, use the following command. ● Set the LACP timeout value to 30 seconds.
Figure 65. Shared LAG State Tracking To avoid packet loss, redirect traffic through the next lowest-cost link (R3 to R4). Dell EMC Networking OS has the ability to bring LAG 2 down if LAG 1 fails, so that traffic can be redirected. This redirection is what is meant by shared LAG state tracking. To achieve this functionality, you must group LAG 1 and LAG 2 into a single entity, called a failover group.
Figure 66. Configuring Shared LAG State Tracking The following are shared LAG state tracking console messages: ● 2d1h45m: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 1 ● 2d1h45m: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 2 To view the status of a failover group member, use the show interface port-channel command.
LACP Basic Configuration Example The screenshots in this section are based on the following example topology. Two routers are named ALPHA and BRAVO, and their hostname prompts reflect those names. Figure 67. LACP Basic Configuration Example Configure a LAG on ALPHA The following example creates a LAG on ALPHA.
0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics 136 packets, 16718 bytes, 0 underruns 0 64-byte pkts, 15 over 64-byte pkts, 121 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 136 Multicasts, 0 Broadcasts, 0 Unicasts 0 Vlans, 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec,0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec,0 packets/sec, 0.
Figure 69.
Figure 70.
Bravo(conf-if-po-10)#switch Bravo(conf-if-po-10)#no shut Bravo(conf-if-po-10)#show config ! interface Port-channel 10 no ip address switchport no shutdown ! Bravo(conf-if-po-10)#exit Bravo(conf)#int tengig 3/21 Bravo(conf)#no ip address Bravo(conf)#no switchport Bravo(conf)#shutdown Bravo(conf-if-te-3/21)#port-channel-protocol lacp Bravo(conf-if-te-3/21-lacp)#port-channel 10 mode active Bravo(conf-if-te-3/21-lacp)#no shut Bravo(conf-if-te-3/21)#end ! interface TenGigabitEthernet 3/21 no ip address ! port-ch
Figure 71.
Figure 72.
Figure 73. Inspecting the LAG Status Using the show lacp command The point-to-point protocol (PPP) is a connection-oriented protocol that enables layer two links over various different physical layer connections. It is supported on both synchronous and asynchronous lines, and can operate in Half-Duplex or Full-Duplex mode. It was designed to carry IP traffic but is general enough to allow any type of network layer datagram to be sent over a PPP connection.
29 Layer 2 This chapter describes the Layer 2 features supported on the device. Topics: • • • • • Manage the MAC Address Table MAC Learning Limit NIC Teaming Configure Redundant Pairs Far-End Failure Detection Manage the MAC Address Table You can perform the following management tasks in the MAC address table.
Configuring a Static MAC Address A static entry is one that is not subject to aging. Enter static entries manually. To create a static MAC address entry, use the following command. ● Create a static MAC address entry in the MAC address table. CONFIGURATION mode mac-address-table static Displaying the MAC Address Table To display the MAC address table, use the following command. ● Display the contents of the MAC address table.
Setting the MAC Learning Limit To set a MAC learning limit on an interface, use the following command. ● Specify the number of MAC addresses that the system can learn off a Layer 2 interface. INTERFACE mode mac learning-limit address_limit Three options are available with the mac learning-limit command: ○ dynamic ○ no-station-move ○ station-move NOTE: An SNMP trap is available for mac learning-limit station-move. No other SNMP traps are available for MAC Learning Limit, including limit violations.
mac learning-limit no-station-move The no-station-move option, also known as “sticky MAC,” provides additional port security by preventing a station move. When you configure this option, the first entry in the table is maintained instead of creating an entry on the new interface. no-station-move is the default behavior. Entries created before you set this option are not affected. To display a list of all interfaces with a MAC learning limit, use the following command.
● Display a list of all of the interfaces configured with MAC learning limit or station move violation. CONFIGURATION mode show mac learning-limit violate-action NOTE: When the MAC learning limit (MLL) is configured as no-station-move, the MLL will be processed as static entries internally. For static entries, the MAC address will be installed in all port-pipes, irrespective of the VLAN membership.
mac port-security NIC Teaming NIC teaming is a feature that allows multiple network interface cards in a server to be represented by one MAC address and one IP address in order to provide transparent redundancy, balancing, and to fully utilize network adapter resources. The following illustration shows a topology where two NICs have been teamed together. In this case, if the primary NIC fails, traffic switches to the secondary NIC because they are represented by the same set of addresses. Figure 74.
Figure 75. Configuring the mac-address-table station-move refresh-arp Command Configure Redundant Pairs Networks that employ switches that do not support the spanning tree protocol (STP) — for example, networks with digital subscriber line access multiplexers (DSLAM) — cannot have redundant links between switches because they create switching loops (as shown in the following illustration).
Figure 76. Configuring Redundant Layer 2 Pairs without Spanning Tree You configure a redundant pair by assigning a backup interface to a primary interface with the switchport backup interface command. Initially, the primary interface is active and transmits traffic and the backup interface remains down. If the primary fails for any reason, the backup transitions to an active Up state. If the primary interface fails and later comes back up, it remains as the backup interface for the redundant pair.
As shown in the above illustration, interface 3/41 is a backup interface for 3/42, and 3/42 is in the Down state. If 3/41 fails, 3/42 transitions to the Up state, which makes the backup link active. A message similar to the following message appears whenever you configure a backup port.
Apr 9 00:16:29: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Te 1/2 DellEMC(conf-if-po-1)# Far-End Failure Detection Far-end failure detection (FEFD) is a protocol that senses remote data link errors in a network. FEFD responds by sending a unidirectional report that triggers an echoed response after a specified time interval. You can enable FEFD globally or locally on an interface basis.
3. When the local interface receives the echoed packet from the remote end, the local interface transitions to the Bi-directional state. 4. If the FEFD enabled system is configured to use FEFD in Normal mode and neighboring echoes are not received after three intervals, (you can set each interval can be set between 3 and 300 seconds) the state changes to unknown. 5.
fefd-global {interval | mode} To display information about the state of each interface, use the show fefd command in EXEC privilege mode. DellEMC#show fefd FEFD is globally 'ON', interval is 3 seconds, mode is 'Normal'.
Debugging FEFD To debug FEFD, use the first command. To provide output for each packet transmission over the FEFD enabled connection, use the second command. ● Display output whenever events occur that initiate or disrupt an FEFD enabled connection. EXEC Privilege mode debug fefd events ● Provide output for each packet transmission over the FEFD enabled connection.
30 Link Layer Discovery Protocol (LLDP) This chapter describes how to configure and use the link layer discovery protocol (LLDP). Topics: • • • • • • • • • • • • • • • • • • 802.
Figure 78. Type, Length, Value (TLV) Segment TLVs are encapsulated in a frame called an LLDP data unit (LLDPDU) (shown in the following table), which is transmitted from one LLDP-enabled device to its LLDP-enabled neighbors. LLDP is a one-way protocol. LLDP-enabled devices (LLDP agents) can transmit and/or receive advertisements, but they cannot solicit and do not respond to advertisements. There are five types of TLVs. All types are mandatory in the construction of an LLDPDU except Optional TLVs.
Optional TLVs The Dell EMC Networking OS supports these optional TLVs: management TLVs, IEEE 802.1 and 802.3 organizationally specific TLVs, and TIA-1057 organizationally specific TLVs. Management TLVs A management TLV is an optional TLVs sub-type. This kind of TLV contains essential management information about the sender. Organizationally Specific TLVs A professional organization or a vendor can define organizationally specific TLVs.
Table 53. Optional TLV Types (continued) Type TLV Description port belongs (and the untagged VLAN to which a port belongs if the port is in Hybrid mode). 127 Protocol Identity Indicates the protocols that the port can process. Dell EMC Networking OS does not currently support this TLV. 127 MAC/PHY Configuration/Status Indicates the capability and current setting of the duplex status and bit rate, and whether the current settings are the result of auto-negotiation.
TIA Organizationally Specific TLVs The Dell EMC Networking system is an LLDP-MED Network Connectivity Device (Device Type 4). Network connectivity devices are responsible for: ● transmitting an LLDP-MED capability TLV to endpoint devices ● storing the information that endpoint devices advertise The following table describes the five types of TIA-1057 Organizationally Specific TLVs. Table 54.
Table 54. TIA-1057 (LLDP-MED) Organizationally Specific TLVs (continued) Type SubType TLV Description 127 11 Inventory — Asset ID Indicates a user specified device number to manage inventory. 127 12–255 Reserved — LLDP-MED Capabilities TLV The LLDP-MED capabilities TLV communicates the types of TLVs that the endpoint device and the network connectivity device support. LLDP-MED network connectivity devices must transmit the Network Policies TLV.
LLDP-MED Network Policies TLV A network policy in the context of LLDP-MED is a device’s VLAN configuration and associated Layer 2 and Layer 3 configurations. LLDP-MED network policies TLV include: ● VLAN ID ● VLAN tagged or untagged status ● Layer 2 priority ● DSCP value An integer represents the application type (the Type integer shown in the following table), which indicates a device function for which a unique network policy is defined.
Extended Power via MDI TLV The extended power via MDI TLV enables advanced PoE management between LLDP-MED endpoints and network connectivity devices. Advertise the extended power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. ● Power Type — there are two possible power types: power source entity (PSE) or power device (PD). The Dell EMC Networking system is a PSE, which corresponds to a value of 0, based on the TIA-1057 specification.
● 802.1X controlled ports do not allow LLDPDUs until the connected device is authenticated. CONFIGURATION versus INTERFACE Configurations All LLDP configuration commands are available in PROTOCOL LLDP mode, which is a sub-mode of the CONFIGURATION mode and INTERFACE mode. ● Configurations made at the CONFIGURATION level are global; that is, they affect all interfaces on the system.
Enabling LLDP on Management Ports LLDP on management ports is enabled by default. To enable LLDP on management ports, use the following command. 1. Enter Protocol LLDP mode. CONFIGURATION mode protocol lldp 2. Enter LLDP management-interface mode. LLDP-MANAGEMENT-INTERFACE mode management-interface 3. Enable LLDP. PROTOCOL LLDP mode no disable Disabling and Undoing LLDP on Management Ports To disable or undo LLDP on management ports, use the following command. 1. Enter Protocol LLDP mode.
○ ○ ○ ○ ○ ○ ○ ○ location-identification power-via-mdi softphone-voice streaming-video video-conferencing video-signaling voice voice-signaling In the following example, LLDP is enabled globally. R1 and R2 are transmitting periodic LLDPDUs that contain management, 802.1, and 802.3 TLVs. Figure 84. Configuring LLDP Storing and Viewing Unrecognized LLDP TLVs Dell EMC Networking OS provides support to store unrecognized (reserved and organizational specific) LLDP TLVs.
NOTE: The system increments the TLV discard counter and does not store unrecognized LLDP TLV information in following scenarios: ● If there are multiple TLVs with the same information is received ● If DCBX is down on the receiving interface The organizational specific TLV list is limited to store 256 entries per neighbor. If TLV entries are more than 256, then the oldest entry (of that neighbor) in the list is replaced.
Viewing Information Advertised by Adjacent LLDP Neighbors To view brief information about adjacent devices or to view all the information that neighbors are advertising, use the following commands. ● Display brief information about adjacent devices. show lldp neighbors ● Display all of the information that neighbors are advertising.
1000BASE-T half duplex mode Operational MAU type: unknown UnknownTLVList: OrgUnknownTLVList: ((f8-b1-56), 24, 1) ((f8-b1-56), 23, 1) ((f8-b1-56), 22, 1) ((f8-b1-56), 21, 7) ((00-80-c2), 7, 5) --------------------------------------------------------------------------Following note is applicable only in platforms that support 25G interfaces: NOTE: Since different port types are shown in two letters, the 25G interface is represented as tf (Twentyfive) in show lldp neighbors output.
Total Neighbor information Age outs: 0 Total Multiple Neighbors Detected: 0 Total Frames Discarded: 0 Total In Error Frames: 0 Total Unrecognized TLVs: 1056 Total TLVs Discarded: 0 Next packet will be sent after 16 seconds The neighbors are given below: ----------------------------------------------------------------------- 4) 4) 4) 4) 4) 4) Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port
R1(conf-lldp)#hello 25 R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description hello 25 no disable R1(conf-lldp)#no hello R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)# Configuring LLDP Notification I
mode tx ● Receive only. CONFIGURATION mode or INTERFACE mode mode rx ● Return to the default setting.
protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description multiplier 5 no disable R1(conf-lldp)#no multiplier R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)# Debugging LLDP You can view the TLVs that your system is sending and rece
The following is an example of LLDPDU with both (Reserved and Organizational specific) unrecognized TLVs.
Table 58. LLDP Configuration MIB Objects (continued) MIB Object Category LLDP Variable LLDP MIB Object Description statsFramesOutTotal lldpStatsTxPortFramesTotal Total number of LLDP frames transmitted through the port. statsTLVsDiscardedTotal lldpStatsRxPortTLVsDiscardedTot al Total number of TLVs received then discarded. statsTLVsUnrecognizedTotal lldpStatsRxPortTLVsUnrecognized Total number of all TLVs the local Total agent does not recognize. Table 59.
Table 59. LLDP System MIB Objects (continued) TLV Type TLV Name TLV Variable OID System LLDP MIB Object Remote lldpRemManAddrIfId Local lldpLocManAddrOID Remote lldpRemManAddrOID Table 60. LLDP 802.
Table 61.
Table 61.
31 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems (OSs). NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
Limitations of the NLB Feature The following limitations apply to switches on which you configure NLB: ● The NLB Unicast mode uses switch flooding to transmit all packets to all the servers that are part of the VLAN. When a large volume of traffic is processed, the clustering performance might be impacted in a small way. This limitation is applicable to switches that perform unicast flooding in the software. ● The ip vlan-flooding command applies globally across the system and for all VLANs.
There might be some ARP table entries that are resolved through ARP packets, which had the Ethernet MAC SA different from the MAC information inside the ARP packet. This unicast data traffic flooding occurs only for those packets that use these ARP entries. Enabling a Switch for Multicast NLB To enable a switch for Multicast NLB mode, perform the following steps: 1.
32 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) is supported on Dell EMC Networking OS. Protocol Overview MSDP is a Layer 3 protocol that connects IPv4 protocol-independent multicast-sparse mode (PIM-SM) domains. A domain in the context of MSDP is a contiguous set of routers operating PIM within a common boundary defined by an exterior gateway protocol, such as border gateway protocol (BGP).
Figure 87.
Implementation Information The Dell EMC Networking OS implementation of MSDP is in accordance with RFC 3618 and Anycast RP is in accordance with RFC 3446. Configure Multicast Source Discovery Protocol Configuring MSDP is a four-step process. 1. Enable an exterior gateway protocol (EGP) with at least two routing domains. Refer to the following figures. The MSDP Sample Configurations show the OSPF-BGP configuration used in this chapter for MSDP.
Figure 88.
Figure 89.
Figure 90.
Figure 91. Configuring MSDP Enable MSDP Enable MSDP by peering RPs in different administrative domains. 1. Enable MSDP. CONFIGURATION mode ip multicast-msdp 2. Peer PIM systems in different administrative domains. CONFIGURATION mode ip msdp peer connect-source R3(conf)#ip multicast-msdp R3(conf)#ip msdp peer 192.168.0.
Multicast sources in remote domains are stored on the RP in the source-active cache (SA cache). The system does not create entries in the multicast routing table until there is a local receiver for the corresponding multicast group. R3#show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.
CONFIGURATION mode clear ip msdp sa-cache [group-address | local | rejected-sa] Enabling the Rejected Source-Active Cache To cache rejected sources, use the following command. Active sources can be rejected because the RPF check failed, the SA limit is reached, the peer RP is unreachable, or the SA message has a format error. ● Cache rejected sources.
Figure 92.
Figure 93.
Figure 94. MSDP Default Peer, Scenario 4 Specifying Source-Active Messages To specify messages, use the following command. ● Specify the forwarding-peer and originating-RP from which all active sources are accepted without regard for the RPF check. CONFIGURATION mode ip msdp default-peer ip-address list If you do not specify an access list, the peer accepts all sources that peer advertises. All sources from RPs that the ACL denies are subject to the normal RPF check. DellEMC(conf)#ip msdp peer 10.0.50.
DellEMC#ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 3 rejected SAs received, cache-size 32766 UpTime GroupAddr SourceAddr RPAddr 00:33:18 229.0.50.64 24.0.50.64 200.0.1.50 00:33:18 229.0.50.65 24.0.50.65 200.0.1.50 00:33:18 229.0.50.66 24.0.50.66 200.0.1.50 LearnedFrom 10.0.50.2 10.0.50.2 10.0.50.2 Reason Rpf-Fail Rpf-Fail Rpf-Fail Limiting the Source-Active Messages from a Peer To limit the source-active messages from a peer, use the following commands. 1.
Preventing MSDP from Caching a Remote Source To prevent MSDP from caching a remote source, use the following commands. 1. OPTIONAL: Cache sources that the SA filter denies in the rejected SA cache. CONFIGURATION mode ip msdp cache-rejected-sa 2. Prevent the system from caching remote sources learned from a specific peer based on source and group. CONFIGURATION mode ip msdp sa-filter list out peer list ext-acl As shown in the following example, R1 is advertising source 10.11.4.2.
GroupAddr SourceAddr RPAddr LearnedFrom 239.0.0.1 10.11.4.2 192.168.0.1 local R3(conf)#do show ip msdp sa-cache MSDP Source-Active Cache - 1 entries GroupAddr SourceAddr RPAddr LearnedFrom 239.0.0.1 10.11.4.2 192.168.0.1 192.168.0.1 Expire 70 UpTime 00:27:20 Expire 1 UpTime 00:10:29 [Router 3] R3(conf)#do show ip msdp sa-cache R3(conf)# To display the configured SA filters for a peer, use the show ip msdp peer command from EXEC Privilege mode.
clear ip msdp peer peer-address R3(conf)#do show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.3(639) Connect Source: Lo 0 State: Established Up/Down Time: 00:04:26 Timers: KeepAlive 30 sec, Hold time 75 sec SourceActive packet count (in/out): 5/0 SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: myremotefilter Output (S,G) filter: none R3(conf)#do clear ip msdp peer 192.168.0.1 R3(conf)#do show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 0.0.0.
1. All the RPs serving a given group are configured with an identical anycast address. 2. Sources then register with the topologically closest RP. 3. RPs use MSDP to peer with each other using a unique address. Figure 95. MSDP with Anycast RP Configuring Anycast RP To configure anycast RP, use the following commands. 1. In each routing domain that has multiple RPs serving a group, create a Loopback interface on each RP serving the group with the same IP address. CONFIGURATION mode interface loopback 2.
ip msdp peer 5. Advertise the network of each of the unique Loopback addresses throughout the network. ROUTER OSPF mode network Reducing Source-Active Message Flooding RPs flood source-active messages to all of their peers away from the RP. When multiple RPs exist within a domain, the RPs forward received active source information back to the originating RP, which violates the RFP rule. You can prevent this unnecessary flooding by creating a mesh-group.
ip msdp peer 192.168.0.22 connect-source Loopback 1 ip msdp mesh-group AS100 192.168.0.22 ip msdp originator-id Loopback 1! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 The following example shows an R2 configuration for MSDP with Anycast RP. ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.
interface Loopback 0 ip pim sparse-mode ip address 192.168.0.3/32 no shutdown ! router ospf 1 network 10.11.6.0/24 area 0 network 192.168.0.3/32 area 0 redistribute static redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.22 remote-as 100 neighbor 192.168.0.22 ebgp-multihop 255 neighbor 192.168.0.22 update-source Loopback 0 neighbor 192.168.0.22 no shutdown ! ip multicast-msdp ip msdp peer 192.168.0.11 connect-source Loopback 0 ip msdp peer 192.168.0.
MSDP Sample Configuration: R2 Running-Config ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.21/24 no shutdown ! interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.0.23/24 no shutdown ! interface Loopback 0 ip address 192.168.0.2/32 no shutdown ! router ospf 1 network 10.11.1.0/24 area 0 network 10.11.4.0/24 area 0 network 192.168.0.
router bgp 200 redistribute ospf 1 neighbor 192.168.0.2 remote-as 100 neighbor 192.168.0.2 ebgp-multihop 255 neighbor 192.168.0.2 update-source Loopback 0 neighbor 192.168.0.2 no shutdown ! ip multicast-msdp ip msdp peer 192.168.0.1 connect-source Loopback 0 ! ip route 192.168.0.2/32 10.11.0.23 MSDP Sample Configuration: R4 Running-Config ip multicast-routing ! interface TenGigabitEthernet 4/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown ! interface TenGigabitEthernet 4/22 ip address 10.10.42.
33 Multicast Listener Discovery Protocol Dell Networking OS Supports Multicast Listener Discovery (MLD) protocol. Multicast Listener Discovery (MLD) is a Layer 3 protocol that IPv6 routers use to learn of the multicast receivers that are directly connected to them and the groups in which the receivers are interested. Multicast routing protocols (like PIM) use the information learned from MLD to route multicast traffic to all interested receivers.
Joining a Multicast Group The Querier periodically sends a General Query to the all-nodes multicast address FF02::1. A host that wants to join a multicast group responds to the general query with a report that contains the group address; the report is also addressed to the group (in the IPv6 Destination Address field). To avoid duplicate reporting, any host that hears a report from another host for the same group in which it itself is interested cancels its report for that group.
| | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +. -+ . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Version 2 multicast listener reports are sent by IP nodes to report (to neighboring routers) the current multicast listening state, or changes in the multicast listening state, of their interfaces.
| | * Source Address [1] * | | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +-+ . . . . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Auxiliary Data . . .
To adjust the query response time, use the following command: INTERFACE Mode ipv6 mld query-max-resp-time Configuring MLD Version To configure MLD version on the system, follow this procedure: Select the MLD version INTERFACE Mode ipv6 mld version {1 | 2} If you do not configure the MLD version, the system defaults to version 2. The ipv6 mld version command is applicable for MLD snooping-enabled interfaces.
INTERFACE Mode ipv6 mld last-member-query-interval Displaying MLD groups table Display MLD groups. Group information can be filtered. To display MLD groups, use the following command: EXEC Privilege show ipv6 mld groups Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 Displaying MLD Interfaces Display MLD interfaces.
34 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP) — specified in IEEE 802.1Q-2003 — is a rapid spanning tree protocol (RSTP)-based spanning tree variation that improves per-VLAN spanning tree plus (PVST+). MSTP allows multiple spanning tree instances and allows you to map many VLANs to one spanning tree instance to reduce the total number of required instances. Protocol Overview MSTP — specified in IEEE 802.
• • • • • • • Modifying Global Parameters Modifying the Interface Parameters Setting STP path cost as constant Configuring an EdgePort Flush MAC Addresses after a Topology Change MSTP Sample Configurations Debugging and Verifying MSTP Configurations Spanning Tree Variations The Dell EMC Networking OS supports four variations of spanning tree, as shown in the following table. Table 62. Spanning Tree Variations Dell EMC Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .
● Prevent Network Disruptions with BPDU Guard ● Enabling SNMP Traps for Root Elections and Topology Changes ● Configuring Spanning Trees as Hitless Enable Multiple Spanning Tree Globally MSTP is not enabled by default. To enable MSTP globally, use the following commands. When you enable MSTP, all physical, VLAN, and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the MSTI 0. ● Within an MSTI, only one path from any bridge to any other bridge is enabled.
protocol spanning-tree mstp no disable MSTI 1 VLAN 100 MSTI 2 VLAN 200-300 All bridges in the MSTP region must have the same VLAN-to-instance mapping. To view which instance a VLAN is mapped to, use the show spanning-tree mst vlan command from EXEC Privilege mode.
To view the bridge priority, use the show config command from PROTOCOL MSTP mode. R3(conf-mstp)#msti 2 bridge-priority 0 1d2h51m: %RPM0-P:RP2 %SPANMGR-5-STP_ROOT_CHANGE: MSTP root changed for instance 2. My Bridge ID: 0:0001.e809.c24a Old Root: 32768:0001.e806.953e New Root: 0:0001.e809.c24a R3(conf-mstp)#show config ! protocol spanning-tree mstp no disable MSTI 1 VLAN 100 MSTI 2 VLAN 200,300 MSTI 2 bridge-priority 0 Interoperate with Non-Dell Bridges Dell EMC Networking OS supports only one MSTP region.
● Max-age — the length of time the bridge maintains configuration information before it refreshes that information by recomputing the MST topology. ● Max-hops — the maximum number of hops a BPDU can travel before a receiving switch discards it. NOTE: Dell EMC Networking recommends that only experienced network administrators change MSTP parameters. Poorly planned modification of MSTP parameters can negatively affect network performance.
Table 63.
Configuring an EdgePort The EdgePort feature enables interfaces to begin forwarding traffic approximately 30 seconds sooner. In this mode, an interface forwards frames by default until it receives a BPDU that indicates that it should behave otherwise; it does not go through the Learning and Listening states. The bpduguard shutdown-on-violation option causes the interface hardware to be shut down when it receives a BPDU.
Figure 97. MSTP with Three VLANs Mapped to Two Spanning Tree Instances Router 1 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3. Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
Router 2 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3. Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
! (Step 3) interface Vlan 100 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown SFTOS Example Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3.
Debugging and Verifying MSTP Configurations To debut and verify MSTP configuration, use the following commands. ● Display BPDUs. EXEC Privilege mode debug spanning-tree mstp bpdu ● Display MSTP-triggered topology change messages. debug spanning-tree mstp events To ensure all the necessary parameters match (region name, region version, and VLAN to instance mapping), examine your individual routers. To show various portions of the MSTP configuration, use the show spanning-tree mst commands.
Name: Tahiti, Rev: 123 (MSTP region name and revision), Int Root Path Cost: 0 Rem Hops: 19, Bridge Id: 32768:0001.e8d5.cbbd 4w0d4h : INST 1 (MSTP Instance): Flags: 0x78, Reg Root: 32768:0001.e806.953e, Int Root Cost: 0 Brg/Port Prio: 32768/128, Rem Hops: 19 INST 2 (MSTP Instance): Flags: 0x78, Reg Root: 32768:0001.e806.
35 Multicast Features NOTE: Multicast routing is supported on secondary IP addresses; it is not supported on IPv6. NOTE: Multicast routing is supported across default and non-default virtual routing and forwarding (VRFs).
Protocol Ethernet Address RIP 01:00:5e:00:00:09 NTP 01:00:5e:00:01:01 VRRP 01:00:5e:00:00:12 PIM-SM 01:00:5e:00:00:0d ● ● ● ● The Dell EMC Networking OS implementation of MTRACE is in accordance with IETF draft draft-fenner-traceroute-ipm. Multicast is not supported on secondary IP addresses. If you enable multicast routing, egress Layer 3 ACL is not applied to multicast data traffic. Multicast traffic can be forwarded to a maximum of 15 VLANs with the same outgoing interface.
● Limit the total number of multicast routes on the system. CONFIGURATION mode ip multicast-limit The range is from 1 to 16000. The default is 4000. NOTE: The IN-L3-McastFib CAM partition stores multicast routes and is a separate hardware limit that exists per port-pipe. Any software-configured limit may supersede this hardware space limitation. The opposite is also true, the CAM partition might not be exhausted at the time the system-wide route limit is reached using the ip multicast-limit command.
Figure 98. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 64. Preventing a Host from Joining a Group — Description Location Description 1/21 ● ● ● ● Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 ● ● ● ● Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Table 64. Preventing a Host from Joining a Group — Description (continued) Location Description 2/11 ● ● ● ● Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 ● ● ● ● Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 ● ● ● ● Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 ● ● ● ● Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
but no outgoing interfaces are listed. R2 has no filter, so it is allowed to forward both groups. As a result, Receiver 1 receives only one transmission, while Receiver 2 receives duplicate transmissions. Figure 99. Preventing a Source from Transmitting to a Group The following table lists the location and description shown in the previous illustration. Table 65.
Table 65. Preventing a Source from Transmitting to a Group — Description (continued) Location Description ● no shutdown 2/11 ● ● ● ● Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 ● ● ● ● Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 ● ● ● ● Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.
Understanding Multicast Traceroute (mtrace) Multicast Traceroute (mtrace) is a multicast diagnostic facility used for tracing multicast paths. Mtrace enables you to trace the path that a multicast packet takes from its source to the destination. When you initiate mtrace from a source to a destination, an mtrace Query packet with IGMP type 0x1F is sent to the last-hop multicast router for the given destination. The mtrace query packet is forwarded hop-by-hop untill it reaches the last-hop router.
● MTRACE Transit — when a Dell EMC Networking system is an intermediate router between the source and destination in an MTRACE query, Dell EMC Networking OS computes the RPF neighbor for the source, fills in the request, and forwards the request to the RPF neighbor. When a Dell EMC Networking system is the last hop to the destination, Dell EMC Networking OS sends a response to the query. To print the network path, use the following command.
Table 66. mtrace Command Output — Explained (continued) Command Output Description From source (?) to destination (?) In case the provided source or destination IP can be resolved to a hostname the corresponding name will be displayed. In cases where the IP cannot be resolved, it is displayed as (?) 0 1.1.1.1 --> Destination The first row in the table corresponds to the destination provided by the user. -1 1.1.1.1 PIM Reached RP/Core 103.103.103.
Table 67. Supported Error Codes (continued) Error Code Error Name Description 0x81 NO_SPACE There is not enough room to insert another response data block in the packet. mtrace Scenarios This section describes various scenarios that may result when an mtrace command is issued. The following table describes various scenarios when the mtrace command is issued: Table 68.
Table 68. Mtrace Scenarios (continued) Scenario You invoke a weak mtrace request by specifying only the source without specifying the mulicast tree or multicast group information for the source. Mtrace traces a path towards the source by using the RPF neighbor at each node. Output R1>mtrace 103.103.103.3 Type Ctrl-C to abort. Querying reverse path for source 103.103.103.
Table 68. Mtrace Scenarios (continued) Scenario When you issue the mtrace command with the source and multicast group information, if a multicast route is not present on a particular node, then the NO ROUTE error code is displayed on the node. In this scenario, the Source Network/Mask column for that particular node displays the the value as default.
Table 68. Mtrace Scenarios (continued) Scenario Output ----------------------------------------------------------------- If the destination provided in the command is not a valid receiver for the multicast group, the last hop router for the destination provides the WRONG LAST HOP error code. If the last-hop router contains a path to the source, the path is traced irrespective of the incorrect destination.
Table 68. Mtrace Scenarios (continued) Scenario Output 0 1.1.1.1 --> Destination -1 * * * * ----------------------------------------------------------------Timed out receiving responses Perhaps no local router has a route for source, the receiver is not a member of the multicast group or the multicast ttl is too low. While traversing the path from source to destination, if the mtrace packet exhausts the maximum buffer size of the packet, then NO SPACE error is displayed in the output.
Table 68. Mtrace Scenarios (continued) Scenario Output Querying reverse path for source 6.6.6.6 to destination 4.4.4.5 via RPF From source (?) to destination (?) ---------------------------------------------------------------|Hop| OIF IP |Proto| Forwarding Code |Source Network/Mask| ---------------------------------------------------------------0 4.4.4.5 --> Destination -1 4.4.4.4 PIM 6.6.6.0/24 -2 20.20.20.2 PIM 6.6.6.0/24 -3 10.10.10.1 PIM RPF Interface 6.6.6.
36 Multicast Listener Discovery Protocol Dell Networking OS Supports Multicast Listener Discovery (MLD) protocol. Multicast Listener Discovery (MLD) is a Layer 3 protocol that IPv6 routers use to learn of the multicast receivers that are directly connected to them and the groups in which the receivers are interested. Multicast routing protocols (like PIM) use the information learned from MLD to route multicast traffic to all interested receivers.
Joining a Multicast Group The Querier periodically sends a General Query to the all-nodes multicast address FF02::1. A host that wants to join a multicast group responds to the general query with a report that contains the group address; the report is also addressed to the group (in the IPv6 Destination Address field). To avoid duplicate reporting, any host that hears a report from another host for the same group in which it itself is interested cancels its report for that group.
| | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +. -+ . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Version 2 multicast listener reports are sent by IP nodes to report (to neighboring routers) the current multicast listening state, or changes in the multicast listening state, of their interfaces.
| | * Source Address [1] * | | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +-+ . . . . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Auxiliary Data . . .
To adjust the query response time, use the following command: INTERFACE Mode ipv6 mld query-max-resp-time Clearing MLD groups Clear a specific group or all groups on an interface from the multicast routing table. To clear MLD groups, use the following command: EXEC Privilege clear ipv6 mld groups Debugging MLD Display Dell Networking OS messages about the MLD process.
show ipv6 mld groups Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 Displaying MLD Interfaces Display MLD interfaces.
NOTE: Under the default configuration, there is no need to configure ipv6 mld snooping for any VLAN. Configure the switch as a querier Hosts that do not support unsolicited reporting wait for a general query before sending a membership report. When the multicast source and receivers are in the same VLAN, multicast traffic is not routed, and so there is no querier.
37 Object Tracking IPv4 or IPv6 object tracking is available on Dell EMC Networking OS. Object tracking allows the Dell EMC Networking OS client processes, such as virtual router redundancy protocol (VRRP), to monitor tracked objects (for example, interface or link status) and take appropriate action when the state of an object changes. NOTE: In Dell EMC Networking OS release version 8.4.1.0, object tracking is supported only on VRRP.
Figure 100. Object Tracking Example When you configure a tracked object, such as an IPv4/IPv6 a route or interface, you specify an object number to identify the object. Optionally, you can also specify: ● UP and DOWN thresholds used to report changes in a route metric. ● A time delay before changes in a tracked object’s state are reported to a client. Track Layer 2 Interfaces You can create an object to track the line-protocol state of a Layer 2 interface.
A tracked route matches a route in the routing table only if the exact address and prefix length match an entry in the routing table. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact address and prefix length, the tracked route is considered to be DOWN.
VRRP Object Tracking As a client, VRRP can track up to 20 objects (including route entries, and Layer 2 and Layer 3 interfaces) in addition to the 12 tracked interfaces supported for each VRRP group. You can assign a unique priority-cost value from 1 to 254 to each tracked VRRP object or group interface. The priority cost is subtracted from the VRRP group priority if a tracked VRRP object is in a DOWN state.
show track object-id DellEMC(conf)#track 100 interface tengigabitethernet 1/1 line-protocol DellEMC(conf-track-100)#delay up 20 DellEMC(conf-track-100)#description San Jose data center DellEMC(conf-track-100)#end DellEMC#show track 100 Track 100 Interface TenGigabitEthernet 1/1 line-protocol Description: San Jose data center Tracking a Layer 3 Interface You can create an object that tracks the routing status of an IPv4 or IPv6 Layer 3 interface.
The following is an example of configuring object tracking for an IPv4 interface: DellEMC(conf)#track 101 interface tengigabitethernet 1/2 ip routing DellEMC(conf-track-101)#delay up 20 DellEMC(conf-track-101)#description NYC metro DellEMC(conf-track-101)#end DellEMC#show track 101 Track 101 Interface TenGigabitEthernet 7/2 ip routing Description: NYC metro The following is an example of configuring object tracking for an IPv6 interface: DellEMC(conf)#track 103 interface tengigabitethernet 1/11 ipv6 routing
○ For ISIS, you can set the resolution in the range from 1 to 1000, where the default is 10. ○ For OSPF, you can set the resolution in the range from 1 to 1592, where the default is 1. ○ The resolution value used to map static routes is not configurable. By default, Dell EMC Networking OS assigns a metric of 0 to static routes. ○ The resolution value used to map RIP routes is not configurable. The RIP hop-count is automatically multiplied by 16 to scale it.
Track 105 IPv6 route 1234::/64 reachability Description: Headquarters Reachability is Down (route not in route table) 2 changes, last change 00:03:03 Configuring track reachability refresh interval If there is no entry in ARP table or if the next-hop address in the ARP cache ages out for a route tracked for its reachability, an attempt is made to check if the next-hop address is reachable after a certain refresh interval to see if the next-hop address appear in the ARP cache before considering it as DOWN.
Valid delay times are from 0 to 180 seconds. The default is 0. 4. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 5. (Optional) Configure the metric threshold for the UP and/or DOWN routing status to be tracked for the specified route. OBJECT TRACKING mode threshold metric {[up number] [down number]} The default UP threshold is 254.
2 changes, last change 00:16:08 Tracked by: Track 2 IPv6 route 2040::/64 metric threshold Metric threshold is Up (STATIC/0/0) 5 changes, last change 00:02:16 Metric threshold down 255 up 254 First-hop interface is TenGigabitEthernet 1/2 Tracked by: VRRP TenGigabitEthernet 2/30 IPv6 VRID 1 Track 3 IPv6 route 2050::/64 reachability Reachability is Up (STATIC) 5 changes, last change 00:02:16 First-hop interface is TenGigabitEthernet 1/2 Tracked by: VRRP TenGigabitEthernet 2/30 IPv6 VRID 1 Track 4 Interface Ten
track 5 ip route 192.168.0.
38 Open Shortest Path First (OSPFv2 and OSPFv3) Open shortest path first (OSPFv2 for IPv4) and OSPF version 3 (OSPF for IPv6) are supported on Dell EMC Networking OS. This chapter provides a general description of OSPFv2 (OSPF for IPv4) and OSPFv3 (OSPF for IPv6) as supported in the Dell EMC Networking Operating System (OS). NOTE: The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) are the same between OSPFv2 and OSPFv3.
Figure 101. Autonomous System Areas Area Types The backbone of the network is Area 0. It is also called Area 0.0.0.0 and is the core of any AS. All other areas must connect to Area 0. An OSPF backbone is responsible for distributing routing information between areas. It consists of all area border routers, networks not wholly contained in any area, and their attached routers. NOTE: If you configure two non-backbone areas, then you must enable the B bit in OSPF.
Networks and Neighbors As a link-state protocol, OSPF sends routing information to other OSPF routers concerning the state of the links between them. The state (up or down) of those links is important. Routers that share a link become neighbors on that segment. OSPF uses the Hello protocol as a neighbor discovery and keep alive mechanism. After two routers are neighbors, they may proceed to exchange and synchronize their databases, which creates an adjacency.
Backbone Router (BR) A backbone router (BR) is part of the OSPF Backbone, Area 0. This includes all ABRs. It can also include any routers that connect only to the backbone and another ABR, but are only part of Area 0, such as Router I in the previous example. Area Border Router (ABR) Within an AS, an area border router (ABR) connects one or more areas to the backbone. The ABR keeps a copy of the link-state database for every area it connects to, so it may keep multiple copies of the link state database.
● Type 3: Summary LSA (OSPFv2), Inter-Area-Prefix LSA (OSPFv3) — An ABR takes information it has learned on one of its attached areas and can summarize it before sending it out on other areas it is connected to. The link-state ID of the Type 3 LSA is the destination network number. ● Type 4: AS Border Router Summary LSA (OSPFv2), Inter-Area-Router LSA (OSPFv3) — In some cases, Type 5 External LSAs are flooded to areas where the detailed next-hop information may not be available.
Figure 103. Priority and Cost Examples OSPF with Dell EMC Networking OS The Dell EMC Networking OS supports up to 128,000 OSPF routes for OSPFv2. Dell EMC Networking OS version 9.4(0.0) and later support only one OSPFv2 process per VRF. Dell EMC Networking OS version 9.7(0.0) and later support OSPFv3 in VRF. Also, on OSPFv3, Dell EMC Networking OS supports only one OSPFv3 process per VRF. OSPFv2 and OSPFv3 can co-exist but you must configure them individually.
OSPF graceful restart understands that in a modern router, the control plane and data plane functionality are separate, restarting the control plane functionality (such as the failover of the active RPM to the backup in a redundant configuration), does not necessarily have to interrupt the forwarding of data packets.
Multi-Process OSPFv2 with VRF Multi-process OSPF with VRF is supported on the Dell EMC Networking OS. Only one OSPFv2 process per VRF is supported. Multi-process OSPF allows multiple OSPFv2 processes on a single router. Multiple OSPFv2 processes allow for isolating routing domains, supporting multiple route policies and priorities in different domains, and creating smaller domains for easier management. Each OSPFv2 process has a unique process ID and must have an associated router ID.
Adjacent with neighbor 1.1.1.1 (Backup Designated Router) DellEMC(conf-if-te-2/2)# Configuration Information The interfaces must be in Layer 3 mode (assigned an IP address) and enabled so that they can send and receive traffic. The OSPF process must know about these interfaces. To make the OSPF process aware of these interfaces, they must be assigned to OSPF areas. You must configure OSPF GLOBALLY on the system in CONFIGURATION mode.
For a complete list of the OSPF commands, refer to the OSPF section in the Dell EMC Networking OS Command Line Reference Guide document. Enabling OSPFv2 To enable Layer 3 routing, assign an IP address to an interface (physical or Loopback). By default, OSPF, similar to all routing protocols, is disabled. You must configure at least one interface for Layer 3 before enabling OSPFv2 globally. If implementing multi-process OSPF, create an equal number of Layer 3 enabled interfaces and OSPF process IDs.
show ip ospf process-id DellEMC#show ip ospf 55555 Routing Process ospf 55555 with ID 10.10.10.10 Supports only single TOS (TOS0) routes SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Number of area in this router is 0, normal 0 stub 0 nssa 0 DellEMC# Assigning an OSPFv2 Area After you enable OSPFv2, assign the interface to an OSPF area. Set up OSPF areas and enable OSPFv2 on an interface with the network command. You must have at least one AS area: Area 0. This is the backbone area.
To view the configuration, use the show config command in CONFIGURATION ROUTER OSPF mode. OSPF, by default, sends hello packets out to all physical interfaces assigned an IP address that is a subset of a network on which OSPF is enabled. To view currently active interfaces and the areas assigned to them, use the show ip ospf interface command. Example of Viewing Active Interfaces and Assigned Areas DellEMC>show ip ospf 1 interface TenGigabitEthernet 1/17 is up, line protocol is up Internet Address 10.2.2.
show ip ospf process-id [vrf] database database-summary 2. Enter CONFIGURATION mode. EXEC Privilege mode configure 3. Enter ROUTER OSPF mode. CONFIGURATION mode router ospf process-id [vrf] Process ID is the ID assigned when configuring OSPFv2 globally. 4. Configure the area as a stub area. CONFIG-ROUTER-OSPF-id mode area area-id stub [no-summary] Use the keywords no-summary to prevent transmission into the area of summary ASBR LSAs. Area ID is the number or IP address assigned when creating the area.
Internet Address 10.1.2.100/24, Area 1.1.1.1 Process ID 34, Router ID 10.1.2.100, Network Type BROADCAST, Cost: 10 Transmit Delay is 1 sec, State DOWN, Priority 1 Designated Router (ID) 10.1.2.100, Interface address 0.0.0.0 Backup Designated Router (ID) 0.0.0.0, Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 13:39:46 Neighbor Count is 0, Adjacent neighbor count is 0 TenGigabitEthernet 2/1 is up, line protocol is down Internet Address 10.1.3.
Routing Process ospf 1 with ID 192.168.67.2 Supports only single TOS (TOS0) routes SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Convergence Level 0 Min LSA origination 5 secs, Min LSA arrival 1 secs Number of area in this router is 0, normal 0 stub 0 nssa 0 DellEMC# Changing OSPFv2 Parameters on Interfaces In Dell EMC Networking OS, you can modify the OSPF settings on the interfaces. Some interface parameter values must be consistent across all interfaces to avoid routing errors.
ip ospf transmit-delay seconds ○ seconds: the range is from 1 to 65535 (the default is 1 second). The transmit delay must be the same on all routers in the OSPF network. To view interface configurations, use the show config command in CONFIGURATION INTERFACE mode. To view interface status in the OSPF process, use the show ip ospf interface command in EXEC mode. The bold lines in the example show the change on the interface. The change is reflected in the OSPF configuration.
● role — the role or roles the configured router can perform. NOTE: By default, OSPFv2 graceful restart is disabled. To enable and configure OSPFv2 graceful restart, use the following commands. 1. Enable OSPFv2 graceful-restart globally and set the grace period. CONFIG-ROUTEROSPF- id mode graceful-restart grace-period seconds The seconds range is from 40 and 3000.
● Create a prefix list and assign it a unique name. CONFIGURATION mode ip prefix-list prefix-name You are in PREFIX LIST mode. ● Create a prefix list with a sequence number and a deny or permit action. CONFIG- PREFIX LIST mode seq sequence-number {deny |permit} ip-prefix [ge min-prefix-length] [le max-prefixlength] The optional parameters are: ○ ge min-prefix-length: is the minimum prefix length to match (from 0 to 32). ○ le max-prefix-length: is the maximum prefix length to match (from 0 to 32).
Troubleshooting OSPFv2 Use the information in this section to troubleshoot OSPFv2 operation on the switch. Be sure to check the following, as these questions represent typical issues that interrupt an OSPFv2 process. NOTE: The following tasks are not a comprehensive; they provide some examples of typical troubleshooting checks.
default-information originate always router-id 10.10.10.10 DellEMC# Sample Configurations for OSPFv2 The following configurations are examples for enabling OSPFv2. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations. You can copy and paste from these examples to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes.
network 10.0.13.0/24 area 0 network 10.0.23.0/24 area 0 ! interface Loopback 30 ip address 192.168.100.100/24 no shutdown ! interface TenGigabitEthernet 3/1 ip address 10.1.13.3/24 no shutdown ! interface TenGigabitEthernet 3/2 ip address 10.2.13.3/24 no shutdown OSPF Area 0 — Te 2/1 and 2/2 router ospf 22222 network 192.168.100.0/24 area 0 network 10.2.21.0/24 area 0 network 10.2.22.0/24 area 0 ! interface Loopback 20 ip address 192.168.100.
Configuration Task List for OSPFv3 (OSPF for IPv6) This section describes the configuration tasks for Open Shortest Path First version 3 (OSPF for IPv6) on the switch. The configuration options of OSPFv3 are the same as those options for OSPFv2, but you may configure OSPFv3 with differently labeled commands. Specify process IDs and areas and include interfaces and addresses in the process. Define areas as stub or totally stubby.
2. Bring up the interface. CONF-INT-type slot/port mode no shutdown Assigning Area ID on an Interface To assign the OSPFv3 process to an interface, use the following command. The ipv6 ospf area command enables OSPFv3 on an interface and places the interface in the specified area. Additionally, the command creates the OSPFv3 process with ID on the router.
router-id {number} ○ number: the IPv4 address. The format is A.B.C.D. NOTE: Enter the router-id for an OSPFv3 router as an IPv4 IP address. ● Disable OSPF. CONFIGURATION mode no ipv6 router ospf process-id vrf {vrf-name} ● Reset the OSPFv3 process. EXEC Privilege mode clear ipv6 ospf [vrf vrf-name] process Configuring Stub Areas To configure IPv6 stub areas, use the following command. ● Configure the area as a stub area.
Configure the following required and optional parameters: ○ bgp | connected | static: enter one of the keywords to redistribute those routes. ○ metric metric-value: The range is from 0 to 4294967295. ○ metric-type metric-type: enter 1 for OSPFv3 external route type 1 OR 2 for OSPFv3 external route type 2. ○ route-map map-name: enter a name of a configured route map. ○ tag tag-value: The range is from 0 to 4294967295.
○ Planned-only: the OSPFv3 router supports graceful restart only for planned restarts. A planned restart is when you manually enter a redundancy force-failover rpm command to force the primary RPM over to the secondary RPM. During a planned restart, OSPFv3 sends out a Grace LSA before the system switches over to the secondary RPM. OSPFv3 is notified that a planned restart is happening. ○ Unplanned-only: the OSPFv3 router supports graceful-restart only for unplanned restarts.
Brd Rtr Count AS Bdr Rtr Count LSA count Summary LSAs Rtr LSA Count Net LSA Count Inter Area Pfx LSA Count Inter Area Rtr LSA Count Group Mem LSA Count 2 2 12010 1 4 3 12000 0 0 The following example shows the show ipv6 ospf database grace-lsa command. DellEMC#show ipv6 ospf database grace-lsa ! Type-11 Grace LSA (Area 0) LS Age Link State ID Advertising Router LS Seq Number Checksum Length Associated Interface Restart Interval Restart Reason : : : : : : : : : 10 6.16.192.66 100.1.1.
OSPFv3 Authentication Using IPsec: Configuration Notes OSPFv3 authentication using IPsec is implemented according to the specifications in RFC 4552. ● To use IPsec, configure an authentication (using AH) or encryption (using ESP) security policy on an interface or in an OSPFv3 area. Each security policy consists of a security policy index (SPI) and the key used to validate OSPFv3 packets. After IPsec is configured for OSPFv3, IPsec operation is invisible to the user.
○ key: specifies the text string used in authentication. All neighboring OSPFv3 routers must share key to exchange information. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). ● Remove an IPsec authentication policy from an interface.
Configuring IPSec Authentication for an OSPFv3 Area To configure, remove, or display IPSec authentication for an OSPFv3 area, use the following commands. Prerequisite: Before you enable IPsec authentication on an OSPFv3 area, first enable OSPFv3 globally on the router (refer to Configuration Task List for OSPFv3 (OSPF for IPv6)). The security policy index (SPI) value must be unique to one IPSec security policy (authentication or encryption) on the router.
○ key: specifies the text string used in the encryption. All neighboring OSPFv3 routers must share the same key to decrypt information. The required lengths of a non-encrypted or encrypted key are: 3DES - 48 or 96 hex digits; DES - 16 or 32 hex digits; AES-CBC - 32 or 64 hex digits for AES-128 and 48 or 96 hex digits for AES-192. ○ key-encryption-type: (optional) specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted).
Outbound AH Key Transform set : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97e : ah-md5-hmac Crypto IPSec client security policy data Policy name : OSPFv3-0-501 Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0c30808825fb5 Inbound ESP Cipher Key : bbdd96e6eb4828e2
Troubleshooting OSPFv3 The system provides several tools to troubleshoot OSPFv3 operation on the switch. This section describes typical, OSPFv3 troubleshooting scenarios. NOTE: The following troubleshooting section is meant to be a comprehensive list, but only to provide some examples of typical troubleshooting checks.
Table 69. MIB Objects for OSPFv3 (continued) MIB Object OID Description ospfv3AreaEntry 1.3.6.1.2.1.191.1.2.1 Contains information describing the parameter configuration and cumulative statistics of the router’s attached areas. ospfv3AsLsdbEntry 1.3.6.1.2.1.191.1.3.1 Contains OSPFv3 process’s AS-scope link state database. The LSDB contains the AS-scope link state advertisements. ospfv3AreaLsdbEntry 1.3.6.1.2.1.191.1.4.1 Contains OSPFv3 process’s Area-scope link state database.
The OSPFv3 ipv6 ospf area command enables OSPFv3 on the interface and places the interface in an area. With OSPFv2, two commands are required to accomplish the same tasks — the router ospf command to create the OSPF process, then the network area command to enable OSPF on an interface. NOTE: The OSPFv2 network area command enables OSPF on multiple interfaces with the single command. Use the OSPFv3 ipv6 ospf area command on each interface that runs OSPFv3.
Assigning IPv6 Addresses on an Interface To assign IPv6 addresses to an interface, use the following commands. 1. Assign an IPv6 address to the interface. CONF-INT-type slot/port mode ipv6 address ipv6 address IPv6 addresses are normally written as eight groups of four hexadecimal digits; separate each group by a colon (:). The format is A:B:C::F/128. 2. Bring up the interface.
Assigning OSPFv3 Process ID and Router ID to a VRF To assign, disable, or reset OSPFv3 on a non-default VRF, use the following commands. ● Enable the OSPFv3 process on a non-default VRF and enter OSPFv3 mode. CONFIGURATION mode ipv6 router ospf {process ID}} The process ID range is from 0 to 65535. ● Assign the router ID for this OSPFv3 process. CONF-IPV6-ROUTER-OSPF mode router-id {number} ○ number: the IPv4 address. The format is A.B.C.D.
Redistributing Routes You can add routes from other routing instances or protocols to the OSPFv3 process. With the redistribute command, you can include RIP, static, or directly connected routes in the OSPF process. Route redistribution is also supported between OSPF Routing process IDs. To add redistributing routes, use the following command. ● Specify which routes are redistributed into the OSPF process.
● Enable OSPFv3 graceful restart globally by setting the grace period (in seconds). CONF-IPV6-ROUTER-OSPF mode graceful-restart grace-period seconds The valid values are from 40 to 1800 seconds. ● Configure an OSPFv3 interface to not act on the Grace LSAs that it receives from a restarting OSPFv3 neighbor. INTERFACE mode ipv6 ospf graceful-restart helper-reject ● Specify the operating mode and type of events that trigger a graceful restart.
Type Count/Status Oper Status 1 Admin Status 1 Area Bdr Rtr Status 0 AS Bdr Rtr Status 1 AS Scope LSA Count 0 AS Scope LSA Cksum sum 0 Originate New LSAS 73 Rx New LSAS 114085 Ext LSA Count 0 Rte Max Eq Cost Paths 5 GR grace-period 180 GR mode planned and unplanned Area 0 database summary Type Brd Rtr Count AS Bdr Rtr Count LSA count Summary LSAs Rtr LSA Count Net LSA Count Inter Area Pfx LSA Count Inter Area Rtr LSA Count Group Mem LSA Count Count/Status 2 2 12010 1 4 3 12000 0 0 The following example sh
of security services for both IPv4 and IPv6. Insert the ESP header after the IP header and before the next layer protocol header in Transport mode. It is possible to insert the ESP header between the next layer protocol header and encapsulated IP header in Tunnel mode. However, Tunnel mode is not supported in Dell EMC Networking OS. For detailed information about the IP ESP protocol, refer to RFC 4303.
The SPI value must be unique to one IPsec security policy (authentication or encryption) on the router. Configure the same authentication policy (the same SPI and key) on each OSPFv3 interface in a link. ● Enable IPsec authentication for OSPFv3 packets on an IPv6-based interface. INTERFACE mode ipv6 ospf authentication {null | ipsec spi number {MD5 | SHA1} [key-encryption-type] key} ○ ○ ○ ○ null: causes an authentication policy configured for the area to not be inherited on the interface.
● Remove an IPsec encryption policy from an interface. no ipv6 ospf encryption ipsec spi number ● Remove null encryption on an interface to allow the interface to inherit the encryption policy configured for the OSPFv3 area. no ipv6 ospf encryption null ● Display the configuration of IPsec encryption policies on the router. show crypto ipsec policy ● Display the security associations set up for OSPFv3 interfaces in encryption policies.
The configuration of IPsec encryption on an interface-level takes precedence over an area-level configuration. If you remove an interface configuration, an area encryption policy that has been configured is applied to the interface. ● Enable IPsec encryption for OSPFv3 packets in an area.
Inbound ESP SPI Outbound ESP SPI Inbound ESP Auth Key Outbound ESP Auth Key Inbound ESP Cipher Key Outbound ESP Cipher Key Transform set : : : : : : : 502 (0x1F6) 502 (0x1F6) 123456789a123456789b123456789c12 123456789a123456789b123456789c12 123456789a123456789b123456789c123456789d12345678 123456789a123456789b123456789c123456789d12345678 esp-3des esp-md5-hmac Crypto IPSec client security policy data Policy name Policy refcount Inbound AH SPI Outbound AH SPI Inbound AH Key Outbound AH Key Transform set :
replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE Troubleshooting OSPFv3 The system provides several tools to troubleshoot OSPFv3 operation on the switch. This section describes typical, OSPFv3 troubleshooting scenarios. NOTE: The following troubleshooting section is meant to be a comprehensive list, but only to provide some examples of typical troubleshooting checks.
39 Policy-based Routing (PBR) Policy-based routing (PBR) allows a switch to make routing decisions based on policies applied to an interface. Topics: • • • • Overview Implementing PBR Configuration Task List for Policy-based Routing Sample Configuration Overview When a router receives a packet, the router decides where to forward the packet based on the destination address in the packet, which is used to look up an entry in a routing table.
● ● ● ● Destination IP address and mask Source port Destination port TCP Flags After you apply a redirect-list to an interface, all traffic passing through it is subjected to the rules defined in the redirect-list. Traffic is forwarded based on the following: ● ● ● ● Next-hop addresses are verified. If the specified next hop is reachable, traffic is forwarded to the specified next-hop. If the specified next-hops are not reachable, the normal routing table is used to forward the traffic.
PBR Exceptions (Permit) To create an exception to a redirect list, use thepermit command. Exceptions are used when a forwarding decision should be based on the routing table rather than a routing policy. The Dell EMC Networking OS assigns the first available sequence number to a rule configured without a sequence number and inserts the rule into the PBR CAM region next to the existing entries. Because the order of rules is important, ensure that you configure any necessary sequence numbers.
● ● ● ● source ip-address or any or host ip-address is the Source’s IP address FORMAT: A.B.C.D/NN, or ANY or HOST IP address destination ip-address or any or host ip-address is the Destination’s IP address FORMAT: A.B.C.D/NN, or ANY or HOST IP address To delete a rule, use the no redirect command.
multiple seq redirect commands with the same source and destination address and specify a different next-hop IP address. In this way, the recursive routes are used as different forwarding routes for dynamic failover. If the primary path goes down and the recursive route is removed from the routing table, the seq redirect command is ignored and the next command in the list with a different route is used.
In addition to supporting multiple redirect-lists in a redirect-group, multiple redirect-groups are supported on a single interface. Dell EMC Networking OS has the capability to support multiple groups on an interface for backup purposes. Show Redirect List Configuration To view the configuration redirect list configuration, use the following commands. 1. View the redirect list configuration and the associated interfaces. EXEC mode show ip redirect-list redirect-list-name 2.
Example: Showing CAM PBR Configuration DellEMC#show cam pbr stack-unit 1 port-set 0 TCP Flag: Bit 5 - URG, Bit 4 - ACK, Bit 3 - PSH, Bit 2 - RST, Bit 1 - SYN, Bit 0 - FIN Cam Port VlanID Proto Tcp Src Dst SrcIp DstIp Next-hop Egress Index Flag Port Port MAC Port ---------------------------------------------------------------------------------------------------------------06080 0 N/A IP 0x0 0 0 200.200.200.200 200.200.200.200 199.199.199.199 199.199.199.199 N/A NA 06081 0 N/A TCP 0x10 0 40 234.234.234.
Create the Redirect-List GOLD EDGE_ROUTER(conf-if-Te-2/23)#ip redirect-list GOLD EDGE_ROUTER(conf-redirect-list)#description Route GOLD traffic to ISP_GOLD. EDGE_ROUTER(conf-redirect-list)#direct 10.99.99.254 ip 192.168.1.0/24 any EDGE_ROUTER(conf-redirect-list)#redirect 10.99.99.254 ip 192.168.2.0/24 any EDGE_ROUTER(conf-redirect-list)# seq 15 permit ip any any EDGE_ROUTER(conf-redirect-list)#show config ! ip redirect-list GOLD description Route GOLD traffic to ISP_GOLD. seq 5 redirect 10.99.99.254 ip 192.
144.144.144.144 DellEMC(conf-redirect-list)#end Verify the Status of the Track Objects (Up/Down): DellEMC#show track brief ResId 1 2 3 4 Resource Interface ip routing Interface ipv6 routing IP Host reachability IP Host reachability Parameter Tunnel 1 Tunnel 2 42.1.1.2/32 43.1.1.
Create Track Objects to track the Tunnel Interfaces: DellEMC#configure terminal DellEMC(conf)#track 1 interface tunnel 1 ip routing DellEMC(conf-track-1)#exit DellEMC(conf)#track 2 interface tunnel 2 ipv6 routing DellEMC(conf-track-2)#end Verify the Status of the Track Objects (Up/Down): DellEMC#show track brief ResId Resource 1 Interface ip routing 2 Interface ipv6 routing DellEMC# Parameter Tunnel 1 Tunnel 2 State Up Up LastChange 00:00:00 00:00:00 Create a Redirect-list with Track Objects pertaining
40 PIM Sparse-Mode (PIM-SM) Protocol-independent multicast sparse-mode (PIM-SM) is a multicast protocol that forwards multicast traffic to a subnet only after a request using a PIM Join message; this behavior is the opposite of PIM-Dense mode, which forwards multicast traffic to all subnets until a request to stop.
2. The last-hop DR sends a PIM Join message to the RP. All routers along the way, including the RP, create an (*,G) entry in their multicast routing table, and the interface on which the message was received becomes the outgoing interface associated with the (*,G) entry. This process constructs an RPT branch to the RP. 3. If a host on the same subnet as another multicast receiver sends an IGMP report for the same multicast group, the gateway takes no action.
3. Enable PIM-SM on an interface. Enable multicast routing. CONFIGURATION mode {ip | ipv6} multicast-routing [vrf vrf-name] Related Configuration Tasks The following are related PIM-SM configuration tasks. ● ● ● ● Configuring S,G Expiry Timers Configuring a Static Rendezvous Point Configuring a Designated Router Creating Multicast Boundaries and Domains Enable PIM-SM You must enable PIM-SM on each participating interface. 1. Enable IPv4 or IPv6 multicast routing on the system.
Following is an example of show ip pim neighbor command output: DellEMC#show Neighbor Address 127.87.5.5 127.87.3.5 127.87.50.
Configuring S,G Expiry Timers You can configure a global expiry time (for all [S,G] entries). By default, [S,G] entries expire in 210 seconds. When you create, delete, or update an expiry time, the changes are applied when the keep alive timer refreshes. To configure a global expiry time, use the following command. Enable global expiry timer for S, G entries. CONFIGURATION mode {ip | ipv6} pim sparse-mode sg-expiry-timer seconds The range is from 211 to 86,400 seconds. The default is 210.
Overriding Bootstrap Router Updates PIM-SM routers must know the address of the RP for each group for which they have (*,G) entry. This address is obtained automatically through the bootstrap router (BSR) mechanism or a static RP configuration. Use the following command if you have configured a static RP for a group. If you do not use the override option with the following command, the RPs advertised in the BSR updates take precedence over any statically configured RPs.
INTERFACE mode {ip | ipv6} pim query-interval seconds ● Display the current value of these parameter.
Creating Multicast Boundaries and Domains A PIM domain is a contiguous set of routers that all implement PIM and are configured to operate within a common boundary defined by PIM multicast border routers (PMBRs). PMBRs connect each PIM domain to the rest of the Internet. Create multicast boundaries and domains by filtering inbound and outbound bootstrap router (BSR) messages per interface. The following command is applied to the subsequent inbound and outbound updates.
show ip pim bsr-router Example: DellEMC# show ip pim bsr-router PIMv2 Bootstrap information This system is the Bootstrap Router (v2) BSR address: 7.7.7.7 (?) BSR Priority: 0, Hash mask length: 30 Next bootstrap message in 00:00:08 This system is a candidate BSR Candidate BSR address: 7.7.7.
41 PIM Source-Specific Mode (PIM-SSM) PIM source-specific mode (PIM-SSM) is a multicast protocol that forwards multicast traffic from a single source to a subnet. In the other versions of protocol independent multicast (PIM), a receiver subscribes to a group only. The receiver receives traffic not just from the source in which it is interested but from all sources sending to that group.
Related Configuration Tasks ● Use PIM-SSM with IGMP Version 2 Hosts Enabling PIM-SSM To enable PIM-SSM, follow these steps. 1. Create an ACL that uses permit rules to specify what range of addresses should use SSM. CONFIGURATION mode ip access-list standard name 2. Enter the ip pim ssm-range command and specify the ACL you created. CONFIGURATION mode ip pim ssm-range acl-name To display address ranges in the PIM-SSM range, use the show ip pim ssm-range command from EXEC Privilege mode.
Configuring PIM-SSM with IGMPv2 R1(conf)#do show run pim ! ip pim rp-address 10.11.12.2 group-address 224.0.0.0/4 ip pim ssm-range ssm R1(conf)#do show run acl ! ip access-list standard map seq 5 permit host 239.0.0.2 ! ip access-list standard ssm seq 5 permit host 239.0.0.2 R1(conf)#ip igmp ssm-map map 10.11.5.2 R1(conf)#do show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface Mode Uptime Expires 239.0.0.
Group Address Interface Mode Uptime 239.0.0.2 Vlan 300 IGMPv2-Compat 00:00:36 Member Ports: Te 1/1 R1(conf)#do show ip igmp ssm-map 239.0.0.2 SSM Map Information Group : 239.0.0.2 Source(s) : 10.11.5.2 R1(conf)#do show ip igmp groups detail Interface Group Uptime Expires Router mode Last reporter Last reporter mode Last report Group source Source address 10.11.5.2 00:00:01 Expires Never Last Reporter 10.11.3.2 Vlan 300 239.0.0.2 00:00:01 Never IGMPv2-Compat 10.11.3.
To enable BSR election for IPv4 or IPv6, perform the following steps: 1. Enter the following IPv4 or IPv6 command to make a PIM router a BSR candidate: CONFIGURATION ip pim bsr-candidate ipv6 pim bsr-candidate 2. Enter the following IPv4 or IPv6 command to make a PIM router a RP candidate: CONFIGURATION ip pim rp-candidate ipv6 pim rp-candidate 3. Display IPv4 or IPv6 Bootstrap Router information.
NOTE: You can create the ACL list of multicast prefix using the ip access-list standard command.
42 Port Monitoring Port monitoring (also referred to as mirroring ) allows you to monitor ingress and/or egress traffic on specified ports. The mirrored traffic can be sent to a port to which a network analyzer is connected to inspect or troubleshoot the traffic. Mirroring is used for monitoring Ingress or Egress or both Ingress and Egress traffic on a specific port(s). This mirrored traffic can be sent to a port where a network sniffer can connect and monitor the traffic.
Port Monitoring Port monitoring is supported on both physical and logical interfaces, such as VLAN and port-channel interfaces. The source port (MD) with monitored traffic and the destination ports (MG) to which an analyzer can be attached must be on the same switch. You can configure up to 128 source ports in a monitoring session. Only one destination port is supported in a monitoring session. The platform supports multiple source-destination statements in a single monitor session.
Example of Configuring Another Monitoring Session with a Previously Used Destination Port DellEMC(conf)#monitor session 300 DellEMC(conf-mon-sess-300)#source TenGig 1/17 destination TenGig 1/4 direction tx % Error: Exceeding max MG ports for this MD port pipe.
in the configuration source TenGig 6/1 destination TeGig 6/2 direction tx, if the MD port TenGig 6/1 is an untagged member of any VLAN, all monitored frames that the MG port TeGig 6/2 receives are tagged with the VLAN ID of the MD port. Similarly, if BPDUs are transmitted, the MG port receives them tagged with the VLAN ID 4095. This behavior might result in a difference between the number of egress packets on the MD port and monitored packets on the MG port.
N/A N/A N/A 0 0 1 Te 1/1 N/A Po 10 N/A Vl 40 N/A Te 1/2 No Te 1/2 No Te 1/3 No rx Port 0.0.0.0 0.0.0.0 0 0 No rx Port 0.0.0.0 0.0.0.0 0 0 No rx Flow 0.0.0.0 0.0.0.0 0 0 No NOTE: Source as VLAN is achieved via Flow based mirroring. Please refer section Enabling Flow-Based Monitoring. In the following example, the host and server are exchanging traffic which passes through the uplink interface 1/1.
Enabling Flow-Based Monitoring Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead of all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 3 ingress traffic. You can specify traffic using standard or extended access-lists. NOTE: Flow-based monitoring is supported for known unicast egress traffic. 1. Create a monitoring session. CONFIGURATION mode monitor session session-id 2.
--------- ------ ----------- --------- ----------------- ---- ---- ----------- --------0 Te 1/1 Te 1/2 rx interface Flow-based 0.0.0.0 0 No N/A N/A yes -------0.0.0.
Configuring Remote Port Mirroring Remote port mirroring requires a source session (monitored ports on different source switches), a reserved tagged VLAN for transporting mirrored traffic (configured on source, intermediate, and destination switches), and a destination session (destination ports connected to analyzers on destination switches).
● ● ● ● You can configure any port as a destination port. You can configure additional destination ports in an active session. You can tunnel the mirrored traffic from multiple remote-port source sessions to the same destination port. By default, destination port sends the mirror traffic to the probe port by stripping off the rpm header. We can also configure the destination port to send the mirror traffic with the rpm header intact in the original mirror traffic..
Configuration procedure for Remote Port Mirroring To configure remote port mirroring, you must configure: 1. A reserved VLAN used to transport mirrored packets on source, intermediate, and destination switches 2. A source session that consists of multiple source ports, port channels, and VLANs which are associated with the dedicated VLAN and located on different source switches 3.
Configuring a destination session Following are the steps for configuring a destination session on a switch. You can configure the below steps on other destination switches to configure additional destination ports for this RPM session. 1. Configure the destination session for RPM. CONFIGURATION mode monitor session session-id 2. Associate the Layer 2 VLAN used to transport monitored traffic with this destination session.
DellEMC(conf-if-vl-10)#mode remote-port-mirroring DellEMC(conf-if-vl-10)#tagged tengigabitethernet 1/2 DellEMC(conf-if-vl-10)#exit DellEMC(conf)# DellEMC(conf)#monitor session 1 type rpm DellEMC(conf-mon-sess-1)#source tengigabitethernet 1/1 destination remote-vlan 10 dir rx DellEMC(conf-mon-sess-1)#no disable DellEMC(conf-mon-sess-1)#exit Configuring Remote Port Mirroring on an intermediate switch Following is a sample configuration of RPM on an intermediate switch.
DellEMC(conf-if-vl-20)#tagged tengigabitethernet 1/5 DellEMC(conf-if-vl-20)#exit Configuring Remote Port Mirroring on a destination switch Following is a sample configuration of RPM on a destination switch.
DellEMC(conf-if-vl-30)#tagged tengigabitethernet 1/7 DellEMC(conf-if-vl-30)#exit DellEMC(conf)#monitor session 3 type rpm DellEMC(conf-mon-sess-3)#source remote-vlan 30 destination tengigabitethernet 1/8 DellEMC(conf-mon-sess-3)#tagged destination tengigabitethernet 1/8 DellEMC(conf-mon-sess-3)#exit Encapsulated Remote Port Monitoring Encapsulated Remote Port Monitoring (ERPM) copies traffic from source ports/port-channels or source VLANs and forwards the traffic using routable GRE-encapsulated packets to
Table 70. Configuration steps for ERPM (continued) Step Command Purpose no flow-based command to disable flow-based ERPM. 6 Enter the no disable command to enable the ERPM session. no disable The following example shows an ERPM configuration: DellEMC(conf)#monitor session 0 type erpm DellEMC(conf-mon-sess-0)#source tengigabitethernet 1/9 direction rx DellEMC(conf-mon-sess-0)#source port-channel 1 direction tx DellEMC(conf-mon-sess-0)#erpm source-ip 1.1.1.1 dest-ip 7.1.1.
ERPM Behavior on a typical Dell EMC Networking OS The Dell EMC Networking OS is designed to support only the Encapsulation of the data received / transmitted at the specified source port (Port A). An ERPM destination session / decapsulation of the ERPM packets at the destination Switch are not supported. Figure 109.
○ Either have a Linux server's ethernet port ip as the ERPM destination ip or connect the ingress interface of the server to the ERPM MirrorToPort. The analyzer should listen in the forward/egress interface. If there is only one interface, one can choose the ingress and forward interface to be same and listen in the tx direction of the interface. ○ Download/ Write a small script (for example: erpm.py) such that it will strip the given ERPM packet starting from the bit where GRE header ends.
VLT Fail-over Scenario Consider a scenario where port monitoring is configured to mirror traffic on the source port or LAG of a VLT device to a destination port on an other device on the network. A fail-over occurs when the primary VLT device fails causing the secondary VLT device to take over. At the time of failover, the mirrored packets are dropped for some time. This time period is equivalent to the gracious VLT failover recovery time.
Table 71. RPM over VLT Scenarios (continued) Scenario RPM Restriction Recommended Solution VLT device:source remote vlan destination orphan port. Mirroring VLT LAG across VLT Peers — In this scenario, the VLT LAG on the primary VLT peer is mirrored to an orphan port on the secondary VLT peer through the ICL LAG. The packet analyzer is connected to the secondary VLT peer. No restrictions apply to the RPM session.
43 Private VLANs (PVLAN) The private VLAN (PVLAN) feature is supported on Dell EMC Networking OS. For syntax details about the commands described in this chapter, refer to the Private VLANs commands chapter in the Dell EMC Networking OS Command Line Reference Guide. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same virtual local area network (VLAN).
● Community port — a port that belongs to a community VLAN and is allowed to communicate with other ports in the same community VLAN and with promiscuous ports. ● Host port — in the context of a private VLAN, is a port in a secondary VLAN: ○ The port must first be assigned that role in INTERFACE mode. ○ A port assigned the host role cannot be added to a regular VLAN. ● Isolated port — a port that, in Layer 2, can only communicate with promiscuous ports that are in the same PVLAN.
Configuration Task List The following sections contain the procedures that configure a private VLAN. ● ● ● ● Creating Creating Creating Creating PVLAN Ports a Primary VLAN a Community VLAN an Isolated VLAN Creating PVLAN ports PVLAN ports are ports that will be assigned to the PVLAN. 1. Access INTERFACE mode for the port that you want to assign to a PVLAN. CONFIGURATION mode interface interface 2. Enable the port. INTERFACE mode no shutdown 3. Set the port in Layer 2 mode. INTERFACE mode switchport 4.
interface vlan vlan-id 2. Enable the VLAN. INTERFACE VLAN mode no shutdown 3. Set the PVLAN mode of the selected VLAN to primary. INTERFACE VLAN mode private-vlan mode primary 4. Map secondary VLANs to the selected primary VLAN. INTERFACE VLAN mode private-vlan mapping secondary-vlan vlan-list The list of secondary VLANs can be: ● Specified in comma-delimited (VLAN-ID,VLAN-ID) or hyphenated-range format (VLAN-ID-VLAN-ID). ● Specified with this command even before they have been created.
You can only add host (isolated) ports to the VLAN. Creating an Isolated VLAN An isolated VLAN is a secondary VLAN of a primary VLAN. An isolated VLAN port can only talk with the promiscuous ports in that primary VLAN. 1. Access INTERFACE VLAN mode for the VLAN that you want to make an isolated VLAN. CONFIGURATION mode interface vlan vlan-id 2. Enable the VLAN. INTERFACE VLAN mode no shutdown 3. Set the PVLAN mode of the selected VLAN to isolated. INTERFACE VLAN mode private-vlan mode isolated 4.
Private VLAN Configuration Example The following example shows a private VLAN topology. Figure 110. Sample Private VLAN Topology The following configuration is based on the example diagram for the Z9500: ● Te 1/1 and Te 1/23 are configured as promiscuous ports, assigned to the primary VLAN, VLAN 4000. ● Te 1/25 is configured as a PVLAN trunk port, also assigned to the primary VLAN 4000. ● Te 1/24 and Te 1/47 are configured as host ports and assigned to the isolated VLAN, VLAN 4003.
● The S4810 ports would have the same intra-switch communication characteristics as described for the Z9500. ● For transmission between switches, tagged packets originating from host PVLAN ports in one secondary VLAN and destined for host PVLAN ports in the other switch travel through the promiscuous ports in the local VLAN 4000 and then through the trunk ports (1/25 in each switch). Inspecting the Private VLAN Configuration The standard methods of inspecting configurations also apply in PVLANs.
G - GVRP tagged, M - Vlan-stack NUM * 1 100 P 200 I 201 Status Inactive Inactive Inactive Inactive Description Q Ports primary VLAN in PVLAN T Te 1/19-20 isolated VLAN in VLAN 200 T Te 1/21 The following example shows viewing a private VLAN configuration.
44 Per-VLAN Spanning Tree Plus (PVST+) Per-VLAN spanning tree plus (PVST+) is a variation of spanning tree — developed by a third party — that allows you to configure a separate spanning tree instance for each virtual local area network (VLAN).
Figure 111. Per-VLAN Spanning Tree The Dell EMC Networking OS supports three other variations of spanning tree, as shown in the following table. Table 72. Spanning Tree Variations Dell EMC Networking OS Supports Dell EMC Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .1w Multiple Spanning Tree Protocol (MSTP) 802 .
Configure Per-VLAN Spanning Tree Plus Configuring PVST+ is a four-step process. 1. 2. 3. 4. Configure interfaces for Layer 2. Place the interfaces in VLANs. Enable PVST+. Optionally, for load balancing, select a nondefault bridge-priority for a VLAN.
Influencing PVST+ Root Selection As shown in the previous per-VLAN spanning tree illustration, all VLANs use the same forwarding topology because R2 is elected the root, and all TenGigabitEthernet ports have the same cost. The following per-VLAN spanning tree illustration changes the bridge priority of each bridge so that a different forwarding topology is generated for each VLAN. This behavior demonstrates how you can use PVST+ to achieve load balancing. Figure 112.
Current root has priority 4096, Address 0001.e80d.b6d6 Number of topology changes 5, last change occurred 00:34:37 ago on Te 1/32 Port 375 (TenGigabitEthernet 1/22) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.375 Designated root has priority 4096, address 0001.e80d.b6:d6 Designated bridge has priority 4096, address 0001.e80d.b6:d6 Designated port id is 128.
● Port priority — influences the likelihood that a port is selected to be a forwarding port in case that several ports have the same port cost. The following tables lists the default values for port cost by interface. Table 73.
CAUTION: Configure EdgePort only on links connecting to an end station. EdgePort can cause loops if you enable it on an interface connected to a network. To enable EdgePort on an interface, use the following command. ● Enable EdgePort on an interface. INTERFACE mode spanning-tree pvst edge-port [bpduguard | shutdown-on-violation] The EdgePort status of each interface is given in the output of the show spanning-tree pvst command, as previously shown.
Figure 113. PVST+ with Extend System ID ● Augment the bridge ID with the VLAN ID. PROTOCOL PVST mode extend system-id DellEMC(conf-pvst)#do show spanning-tree pvst vlan 5 brief VLAN 5 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32773, Address 0001.e832.73f7 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32773 (priority 32768 sys-id-ext 5), Address 0001.e832.
no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/22,32 no shutdown ! protocol spanning-tree pvst no disable vlan 100 bridge-priority 4096 Example of PVST+ Configuration (R2) interface TenGigabitEthernet 2/12 no ip address switchport no shutdown ! interface TenGigabitEthernet 2/32 no ip address switchport no shutdown ! interface Vlan 100 no ip address tagged TenGigabitEthernet 2/12,32 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 2/12,32 no shutdown ! inte
45 Quality of Service (QoS) This chapter describes how to use and configure Quality of Service service (QoS) features on the switch. Differentiated service is accomplished by classifying and queuing traffic, and assigning priorities to those queues. Table 74.
Table 74. Dell EMC Networking Operating System (OS) Support for Port-Based, Policy-Based Features (continued) Feature Direction Create Output Policy Maps Egress Specify an Aggregate QoS Policy Egress Create Output Policy Maps Egress Enabling QoS Rate Adjustment Enabling Strict-Priority Queueing Weighted Random Early Detection Egress Create WRED Profiles Egress Figure 114.
• • • • • • • • Guidelines for Configuring ECN for Classifying and Color-Marking Packets Applying Layer 2 Match Criteria on a Layer 3 Interface Applying DSCP and VLAN Match Criteria on a Service Queue Classifying Incoming Packets Using ECN and Color-Marking Guidelines for Configuring ECN for Classifying and Color-Marking Packets Sample configuration to mark non-ecn packets as “yellow” with Multiple traffic class Sample configuration to mark non-ecn packets as “yellow” with single traffic class Enabling Buf
dot1p-priority DellEMC#configure terminal DellEMC(conf)#interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)#switchport DellEMC(conf-if-te-1/1)#dot1p-priority 1 DellEMC(conf-if-te-1/1)#end Honoring dot1p Priorities on Ingress Traffic By default, Dell EMC Networking OS does not honor dot1p priorities on ingress traffic. You can configure this feature on physical interfaces and port-channels, but you cannot configure it on individual interfaces in a port channel.
Configuring Port-Based Rate Shaping Rate shaping buffers, rather than drops, traffic exceeding the specified rate until the buffer is exhausted. If any stream exceeds the configured bandwidth on a continuous basis, it can consume all of the buffer space that is allocated to the port. Dell EMC Networking OS Behavior: Rate shaping is effectively rate limiting because of its smaller buffer size.
Policy-Based QoS Configurations Policy-based QoS configurations consist of the components shown in the following example. Figure 115. Constructing Policy-Based QoS Configurations Classify Traffic Class maps differentiate traffic so that you can apply separate quality of service policies to different types of traffic. For both class maps, Layer 2 and Layer 3, Dell EMC Networking OS matches packets against match criteria in the order that you configure them.
class-map match-any 2. Create a match-all class map. CONFIGURATION mode class-map match-all 3. Specify your match criteria. CLASS MAP mode [seq sequence number] match {ip | ipv6 | ip-any} After you create a class-map, Dell EMC Networking OS places you in CLASS MAP mode. Match-any class maps allow up to five ACLs. Match-all class-maps allow only one ACL. NOTE: Within a class-map, the match rules are installed in the sequence number order. 4. Link the class-map to a queue.
3. Specify your match criteria. CLASS MAP mode [seq sequence number] match mac After you create a class-map, Dell EMC Networking OS places you in CLASS MAP mode. Match-any class maps allow up to five access-lists. Match-all class-maps allow only one. You can match against only one VLAN ID. 4. Link the class-map to a queue.
seq 5 permit ip host 23.64.0.2 any seq 10 deny ip any any ! ip access-list extended AF1-FB2 seq 5 permit ip host 23.64.0.3 any seq 10 deny ip any any ! ip access-list extended AF2 seq 5 permit ip host 23.64.0.5 any seq 10 deny ip any any DellEMC# show cam layer3-qos interface tengigabitethernet 2/4 Cam Port Dscp Proto Tcp Src Dst SrcIp DstIp DSCP Queue Index Flag Port Port Marking ----------------------------------------------------------------------20416 1 18 IP 0x0 0 0 23.64.0.5/32 0.0.0.
Creating an Input QoS Policy To create an input QoS policy, use the following steps. 1. Create a Layer 3 input QoS policy. CONFIGURATION mode qos-policy-input Create a Layer 2 input QoS policy by specifying the keyword layer2 after the qos-policy-input command. 2.
The following table lists the default bandwidth weights for each queue, and their equivalent percentage which is derived by dividing the bandwidth weight by the sum of all queue weights. Table 76. Default Bandwidth Weights Queue Default Bandwidth Percentage for 4– Default Bandwidth Percentage for 8– Queue System Queue System 0 6.67% 1% 1 13.33% 2% 2 26.67% 3% 3 53.33% 4% 4 - 5% 5 - 10% 6 - 25% 7 - 50% NOTE: The system supports 8 data queues.
Applying a Class-Map or Input QoS Policy to a Queue To apply a class-map or input QoS policy to a queue, use the following command. ● Assign an input QoS policy to a queue. POLICY-MAP-IN mode service-queue Applying an Input QoS Policy to an Input Policy Map To apply an input QoS policy to an input policy map, use the following command. ● Apply an input QoS policy to an input policy map.
Table 78. Default dot1p to Queue Mapping (continued) dot1p Queue ID 3 1 4 2 5 3 6 3 7 3 The dot1p value is also honored for frames on the default VLAN. For more information, refer to Priority-Tagged Frames on the Default VLAN. ● Enable the trust dot1p feature. POLICY-MAP-IN mode trust dot1p Mapping dot1p Values to Service Queues All traffic is by default mapped to the same queue, Queue 0.
Creating Output Policy Maps 1. Create an output policy map. CONFIGURATION mode policy-map-output 2. After you create an output policy map, do one or more of the following: Applying an Output QoS Policy to a Queue Specifying an Aggregate QoS Policy Applying an Output Policy Map to an Interface 3. Apply the policy map to an interface. Applying an Output QoS Policy to a Queue To apply an output QoS policy to a queue, use the following command. ● Apply an output QoS policy to queues.
either transmit or drop the packet based on configured queuing behavior. Traffic marked as red (high drop precedence) is dropped. Important Points to Remember ● All DSCP values that are not specified as yellow or red are colored green (low drop precedence). ● A DSCP value cannot be in both the yellow and red lists. Setting the red or yellow list with any DSCP value that is already in the other list results in an error and no update to that DSCP list is made.
Displaying a DSCP Color Policy Configuration To display the DSCP color policy configuration for one or all interfaces, use the show qos dscp-color-policy {summary [interface] | detail {interface}} command in EXEC mode. summary: Displays summary information about a color policy on one or more interfaces. detail: Displays detailed color policy information on an interface interface : Enter the name of the interface that has the color policy configured.
Enabling Strict-Priority Queueing In strict-priority queuing, the system de-queues all packets from the assigned queue before servicing any other queues. You can assign strict-priority to one unicast queue, using the strict-priority command. ● Policy-based per-queue rate shaping is not supported on the queue configured for strict-priority queuing. To use queuebased rate-shaping as well as strict-priority queuing at the same time on a queue, use the Scheduler Strict feature as described in Scheduler Strict .
Table 79. Pre-Defined WRED Profiles Default Profile Name Minimum Threshold Maximum Threshold Maximum Drop Rate wred_drop 0 0 100 wred_teng_y 467 4671 100 wred_teng_g 467 4671 50 wred_fortyg_y 467 4671 50 wred_fortyg_g 467 4671 25 Creating WRED Profiles To create WRED profiles, use the following commands. 1. Create a WRED profile. CONFIGURATION mode wred-profile 2. Specify the minimum and maximum threshold values.
Drop-statistic Dropped Pkts Green Yellow Out of Profile 51623 51300 0 DellEMC# Displaying egress–queue Statistics To display the number of transmitted and dropped packets and their rate on the egress queues of an interface, use the following command: ● Display the number of packets and number of bytes on the egress-queue profile. EXEC Privilege mode show qos statistics egress-queue Pre-Calculating Available QoS CAM Space Before Dell EMC Networking OS version 7.3.
test cam-usage DellEMC# test cam-usage service-policy input pmap_l2 port-set 0 | port pipe Port-pipe | CAM Partition | Available CAM | Estimated CAM | Status ===================================================================== 0 L2ACL 500 200 Allowed(2) Configuring Weights and ECN for WRED The WRED congestion avoidance functionality drops packets to prevent buffering resources from being consumed. Traffic is a mixture of various kinds of packets.
● When WRED is configured on the global service-pool (regardless of whether ECN on global service-pool is configured), and one or more queues are enabled with both WRED and ECN, ECN marking takes effect. The packets are ECN marked up to shared- buffer limits as determined by the shared-ratio for that global service-pool. WRED/ECN configurations for the queues that belong to backplane ports are common to all the backplane ports and cannot be specified separately for each backplane port granularity.
DellEMC(conf-wred) #threshold min 300 max 400 max-drop-rate 80 4. Create a global buffer pool that is a shared buffer pool accessed by multiple queues when the minimum guaranteed buffers for the queue are consumed.
policy-map-input ecn_0_pmap service-queue 0 class-map ecn_0_cmap Applying this policy-map “ecn_0_pmap” will mark all the packets with ‘ecn == 0’ as yellow packets on queue0 (default queue). Classifying Incoming Packets Using ECN and Color-Marking Explicit Congestion Notification (ECN) is a capability that enhances WRED by marking the packets instead of causing WRED to drop them when the threshold value is exceeded.
● PSH ● RST ● URG You can now use the ‘ecn’ match qualifier along with the above TCP flag for classification.
match ip access-group dscp_40 ! class-map match-any class_dscp_50 match ip access-group dscp_50_non_ecn set-color yellow match ip access-group dscp_50 ! policy-map-input pmap_dscp_40_50 service-queue 2 class-map class_dscp_40 service-queue 3 class-map class_dscp_50 Approach with explicit ECN match qualifiers for ECN packets: ! ip access-list standard dscp_50_ecn seq 5 permit any dscp 50 ecn 1 seq 10 permit any dscp 50 ecn 2 seq 15 permit any dscp 50 ecn 3 ! ip access-list standard dscp_40_ecn seq 5 permit a
DellEMC(conf-if-fo-1/49/1)# service-policy input l2p layer2 Applying DSCP and VLAN Match Criteria on a Service Queue You can configure Layer 3 class maps which contain both a Layer 3 Differentiated Services Code Point (DSCP) and IP VLAN IDs as match criteria to filter incoming packets on a service queue on the switch. To configure a Layer 3 class map to classify traffic according to both an IP VLAN ID and DSCP value, use the match ip vlan vlan-id command in class-map input configuration mode.
On ECN deployment, the non-ECN packets that are transmitted on the ECN-WRED enabled interface will be considered as Green packets and will be subject to the early WRED drops. Typically the TCP-acks, OAM, ICMP ping packets will be non-ECN in nature and it is not desirable for this packets getting WRED dropped. In such a condition, it is necessary that the switch is capable to take differentiated actions for ECN/Non-ECN packets.
By default, all packets are considered as ‘green’ (without the rate-policer and trust-diffserve configuration) and hence support would be provided to mark the packets as ‘yellow’ alone will be provided. By default Dell EMC Networking OS drops all the ‘RED’ or ‘violate’ packets.
Sample configuration to mark non-ecn packets as “yellow” with Multiple traffic class Consider the example where there are no different traffic classes that is all the packets are egressing on the default ‘queue0’. Dell EMC Networking OS can be configured as below to mark the non-ecn packets as yellow packets.
! ip access-list standard dscp_40_ecn seq 5 permit any dscp 40 ecn 1 seq 10 permit any dscp 40 ecn 2 seq 15 permit any dscp 40 ecn 3 ! ip access-list standard dscp_50_non_ecn seq 5 permit any dscp 50 ecn 0 ! ip access-list standard dscp_40_non_ecn seq 5 permit any dscp 40 ecn 0 ! class-map match-any class_dscp_40 match ip access-group dscp_40_non_ecn set-color yellow match ip access-group dscp_40_ecn ! class-map match-any class_dscp_50 match ip access-group dscp_50_non_ecn set-color yellow match ip access-g
MCAST 3 0 Unit 1 unit: 3 port: 9 (interface Fo 1/152) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 13 (interface Fo 1/156) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 17 (interface Fo 1/160) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit
UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 11 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 0 Quality of Service (QoS) 765
46 Routing Information Protocol (RIP) The Routing Information Protocol (RIP) tracks distances or hop counts to nearby routers when establishing network connections and is based on a distance-vector algorithm. RIP is based on a distance-vector algorithm; it tracks distances or hop counts to nearby routers when establishing network connections. RIP protocol standards are listed in the Standards Compliance chapter.
Table 81. RIP Defaults Feature Default Interfaces running RIP ● Listen to RIPv1 and RIPv2 ● Transmit RIPv1 RIP timers ● ● ● ● Auto summarization Enabled ECMP paths supported 16 update timer = 30 seconds invalid timer = 180 seconds holddown timer = 180 seconds flush timer = 240 seconds Configuration Information By default, RIP is disabled in Dell EMC Networking OS. To configure RIP, you must use commands in two modes: ROUTER RIP and INTERFACE.
To view the global RIP configuration, use the show running-config command in EXEC mode or the show config command in ROUTER RIP mode. DellEMC(conf-router_rip)#show config ! router rip network 10.0.0.0 DellEMC(conf-router_rip)# When the RIP process has learned the RIP routes, use the show ip rip database command in EXEC mode to view those routes. DellEMC#show ip rip database Total number of routes in RIP database: 978 160.160.0.0/16 [120/1] via 29.10.10.12, 00:00:26, Fa 1/49 160.160.0.0/16 auto-summary 2.0.
● Define a specific router to exchange RIP information between it and the Dell EMC Networking system. ROUTER RIP mode neighbor ip-address You can use this command multiple times to exchange RIP information with as many RIP networks as you want. ● Disable a specific interface from sending or receiving RIP routing information.
○ map-name: the name of a configured route map. To view the current RIP configuration, use the show running-config command in EXEC mode or the show config command in ROUTER RIP mode. Setting the Send and Receive Version To change the RIP version globally or on an interface in Dell EMC Networking OS, use the following command. To specify the RIP version, use the version command in ROUTER RIP mode.
The following example of the show ip protocols command confirms that both versions are sent out that interface. This interface no longer sends and receives the same RIP versions as Dell EMC Networking OS does globally (shown in bold).
Controlling Route Metrics As a distance-vector protocol, RIP uses hop counts to determine the best route, but sometimes the shortest hop count is a route over the lowest-speed link. To manipulate RIP routes so that the routing protocol prefers a different route, manipulate the route by using the offset command. Exercise caution when applying an offset command to routers on a broadcast network, as the router using the offset command is modifying RIP advertisements before sending out those advertisements.
● RIP Configuration on Core 3 ● Core 3 RIP Output ● RIP Configuration Summary Figure 117. RIP Topology Example RIP Configuration on Core2 The following example shows how to configure RIPv2 on a host named Core2. Core2(conf-if-te-2/3)# Core2(conf-if-te-2/3)#router rip Core2(conf-router_rip)#ver 2 Core2(conf-router_rip)#network 10.200.10.0 Core2(conf-router_rip)#network 10.300.10.0 Core2(conf-router_rip)#network 10.11.10.0 Core2(conf-router_rip)#network 10.11.20.
The following example shows the show ip route command to show the RIP setup on Core 2.
! router rip network 10.0.0.0 network 192.168.1.0 network 192.168.2.0 version 2 Core3(conf-router_rip)# Core 3 RIP Output The examples in this section show the core 2 RIP output. ● To display Core 3 RIP database, use the show ip rip database command. ● To display Core 3 RIP setup, use the show ip route command. ● To display Core 3 RIP activity, use the show ip protocols command. The following example shows the show ip rip database command to view the learned RIP routes on Core 3.
Incoming filter for all interfaces is Default redistribution metric is 1 Default version control: receive version 2, send version 2 Interface Recv Send TenGigabitEthernet 3/21 2 2 TenGigabitEthernet 3/11 2 2 TenGigabitEthernet 3/24 2 2 TenGigabitEthernet 3/23 2 2 Routing for Networks: 10.11.20.0 10.11.30.0 192.168.2.0 192.168.1.0 Routing Information Sources: Gateway Distance Last Update 10.11.20.
! router rip version 2 network 10.11.20.0 network 10.11.30.0 network 192.168.1.0 network 192.168.2.
47 Remote Monitoring (RMON) RMON is an industry-standard implementation that monitors network traffic by sharing network monitoring information. RMON provides both 32-bit and 64-bit monitoring facility and long-term statistics collection on Dell EMC Networking Ethernet interfaces. RMON operates with the simple network management protocol (SNMP) and monitors all nodes on a local area network (LAN) segment. RMON monitors traffic passing through the router and segment traffic not destined for the router.
[no] rmon alarm number variable interval {delta | absolute} rising-threshold [value event-number] falling-threshold value event-number [owner string] OR [no] rmon hc-alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] Configure the alarm using the following optional parameters: ○ number: alarm number, an integer from 1 to 65,535, the value must be unique in the RMON Alarm Table.
this command. This configuration also generates an SNMP trap when the event is triggered using the SNMP community string “eventtrap”. DellEMC(conf)#rmon event 1 log trap eventtrap description “High ifOutErrors” owner nms1 Configuring RMON Collection Statistics To enable RMON MIB statistics collection on an interface, use the RMON collection statistics command in INTERFACE CONFIGURATION mode. ● Enable RMON MIB statistics collection.
48 Rapid Spanning Tree Protocol (RSTP) The Rapid Spanning Tree Protocol (RSTP) is a Layer 2 protocol — specified by IEEE 802.1w — that is essentially the same as spanning-tree protocol (STP) but provides faster convergence and interoperability with switches configured with STP and multiple spanning tree protocol (MSTP).
● ● ● ● ● ● Prevent Network Disruptions with BPDU Guard Influencing RSTP Root Selection Configuring Spanning Trees as Hitless Enabling SNMP Traps for Root Elections and Topology Changes Configuring Fast Hellos for Link State Detection Flush MAC Addresses after a Topology Change Important Points to Remember ● RSTP is disabled by default. ● Dell EMC Networking OS supports only one Rapid Spanning Tree (RST) instance.
Enabling Rapid Spanning Tree Protocol Globally Enable RSTP globally on all participating bridges; it is not enabled by default. When you enable RSTP, all physical and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the RST topology. ● Only one path from any bridge to any other bridge is enabled. ● Bridges block a redundant path by disabling one of the link ports. To enable RSTP globally for all Layer 2 interfaces, use the following commands. 1.
To view the interfaces participating in RSTP, use the show spanning-tree rstp command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output. DellEMC#show spanning-tree rstp Root Identifier has priority 32768, Address 0001.e801.cbb4 Root Bridge hello time 2, max age 20, forward delay 15, max hops 0 Bridge Identifier has priority 32768, Address 0001.e801.
Te 3/4 R3# Altr 128.684 128 20000 BLK 20000 P2P No Adding and Removing Interfaces To add and remove interfaces, use the following commands. To add an interface to the Rapid Spanning Tree topology, configure it for Layer 2 and it is automatically added. If you previously disabled RSTP on the interface using the command no spanning-tree 0 command, re-enable it using the spanning-tree 0 command. ● Remove an interface from the Rapid Spanning Tree topology.
hello-time seconds NOTE: With large configurations (especially those configurations with more ports) Dell EMC Networking recommends increasing the hello-time. The range is from 1 to 10. The default is 2 seconds. ● Change the max-age parameter. PROTOCOL SPANNING TREE RSTP mode max-age seconds The range is from 6 to 40. The default is 20 seconds. To view the current values for global parameters, use the show spanning-tree rstp command from EXEC privilege mode.
Influencing RSTP Root Selection RSTP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it is selected as the root bridge. To change the bridge priority, use the following command. ● Assign a number as the bridge priority or designate it as the primary or secondary root. PROTOCOL SPANNING TREE RSTP mode bridge-priority priority-value ○ priority-value The range is from 0 to 65535.
interface TenGigabitEthernet 2/1 no ip address switchport spanning-tree rstp edge-port shutdown DellEMC(conf-if-te-2/1)# Configuring Fast Hellos for Link State Detection Use RSTP fast hellos to achieve sub-second link-down detection so that convergence is triggered faster. The standard RSTP link-state detection mechanism does not offer the same low link-state detection speed. To achieve sub-second link-down detection so that convergence is triggered faster, use RSTP fast hellos.
49 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
50 Security This chapter describes several ways to provide security to the Dell EMC Networking system. For details about all the commands described in this chapter, refer to the Security chapter in the Dell EMC Networking OS Command Reference Guide.
CONFIGURATION mode aaa accounting {commands level | dot1x | exec | rest | suppress | system} {default | name} {start-stop | wait-start | stop-only} {radius | tacacs+} The variables are: ○ system: sends accounting information of any other AAA configuration. ○ exec: sends accounting information when a user has logged in to EXEC mode. ○ dot1x: sends accounting information when a dot1x user has logged in to EXEC mode. ○ command level: sends accounting of commands executed at the specified privilege level.
accounting exec execAcct DellEMC(config-line-vty)# accounting commands 15 com15 DellEMC(config-line-vty)# accounting exec execAcct Monitoring AAA Accounting Dell EMC Networking OS does not support periodic interim accounting because the periodic command can cause heavy congestion when many users are logged in to the network. No specific show command exists for TACACS+ accounting. To obtain accounting records displaying information about users currently logged in, use the following command.
EAP START accounting record: Fri May 10 12:20:43 2019 NAS-IP-Address = 10.16.133.
Acct-Multi-Session-Id = "00-11-22-33-44-55-00-11-33-44-77-88-5e-50-d6-5cc" Acct-Link-Count = 1 Acct-Terminate-Cause = Lost-Carrier Acct-Status-Type = Stop Event-Timestamp = "May 10 2019 23:30:42 CDT" Tmp-String-9 = "ai:" Acct-Unique-Session-Id = "5a761462ef63b815707de5fa1c5ef348" Timestamp = 1557549042 RADIUS Accounting attributes The following tables describe the various types of attributes that identify the supplicant sessions: Table 84.
Table 85. RADIUS Accounting Stop Record Attributes for CLI user (continued) RADIUS Attribute code RADIUS Attribute Description VIRTUAL - for telnet/SSH session. Table 86. Use cases for CLI user to trigger RADIUS Accounting Start/Stop records CLI event Accounting type Attributes CLI user authentication success Start Start record attributes for CLI user. CLI user log-off Stop Stop record attributes with termination cause as User Request (1).
Table 88. RADIUS Accounting Stop Record Attributes for dot1x supplicant (continued) RADIUS Attribute code RADIUS Attribute Description 1 User-Name User name/ Supplicant MAC Address (for MAB). 5 NAS-Port Port on which session is terminated. 6 Service-Type Framed (2) for EAP /Call check (10) for MAB. 8 Framed-IP-Address IPv4 address of supplicant. 168 Framed-IPV6-Address IPv6 address of supplicant. 30 Called-Station-Id Switch MAC Address. 31 Calling-Station-Id Supplicant MAC Address.
Table 89. Use cases for dot1x supplicant to trigger RADIUS Accounting Start/Stop records (continued) dot1x event Accounting type Attributes Configure max supplicant per interface Stop Stop record attributes with termination cause as port-reinitialized (21). Supplicant goes off without explicitly sending EAP logoff Stop Stop record attributes with termination cause as Idle Timeout (4). Periodic Reauth of supplicant Stop Stop record attributes with termination cause as Supplicant restart (19).
Configuring AAA Authentication Login Methods To configure an authentication method and method list, use the following commands. Dell EMC Networking OS Behavior: If you use a method list on the console port in which RADIUS or TACACS is the last authentication method, and the server is not reachable, Dell EMC Networking OS allows access even though the username and password credentials cannot be verified.
CONFIGURATION mode aaa authentication enable default radius tacacs 2. Establish a host address and password. CONFIGURATION mode radius-server host x.x.x.x key some-password 3. Establish a host address and password. CONFIGURATION mode tacacs-server host x.x.x.x key some-password To get enable authentication from the RADIUS server and use TACACS as a backup, issue the following commands. The following example shows enabling authentication from the RADIUS server.
Example: DellEMC(config)#aaa authentication login vty_auth_list radius Force all logged-in users to re-authenticate (y/n)? 3. You are prompted to force the users to re-authenticate whenever there is a change in the RADIUS server list.. CONFIGURATION mode radius-server host IP Address Example: DellEMC(config)#radius-server host 192.100.0.12 Force all logged-in users to re-authenticate (y/n)? DellEMC(config)#no radius-server host 192.100.0.
● Privilege level 1 — is the default level for EXEC mode. At this level, you can interact with the router, for example, view some show commands and Telnet and ping to test connectivity, but you cannot configure the router. This level is often called the “user” level. One of the commands available in Privilege level 1 is the enable command, which you can use to enter a specific privilege level. ● Privilege level 0 — contains only the end, enable, and disable commands.
Configuring the Enable Password Command To configure Dell EMC Networking OS, use the enable command to enter EXEC Privilege level 15. After entering the command, Dell EMC Networking OS requests that you enter a password. Privilege levels are not assigned to passwords, rather passwords are assigned to a privilege level. You can always change a password for any privilege level. To change to a different privilege level, enter the enable command, then the privilege level.
3. Configure level and commands for a mode or reset a command’s level. CONFIGURATION mode privilege mode {level level command | reset command} Configure the following required and optional parameters: ● mode: enter a keyword for the modes (exec, configure, interface, line, route-map, or router) ● level level: the range is from 0 to 15. Levels 0, 1, and 15 are pre-configured. Levels 2 to 14 are available for custom configuration. ● command: an Dell EMC Networking OS CLI keyword (up to five keywords allowed).
snmp-server Modify SNMP parameters DellEMC(conf)# Specifying LINE Mode Password and Privilege You can specify a password authentication of all users on different terminal lines. The user’s privilege level is the same as the privilege level assigned to the terminal line, unless a more specific privilege level is assigned to the user. To specify a password for the terminal line, use the following commands. ● Configure a custom privilege level for the terminal lines.
RADIUS Authentication Dell EMC Networking OS supports RADIUS for user authentication (text password) at login and can be specified as one of the login authentication methods in the aaa authentication login command. When configuring AAA authorization, you can configure to limit the attributes of services available to a user. When you enable authorization, the network access server uses configuration information from the user profile to issue the user's session.
Configuration Task List for RADIUS To authenticate users using RADIUS, you must specify at least one RADIUS server so that the system can communicate with and configure RADIUS as one of your authentication methods. The following list includes the configuration tasks for RADIUS.
Specifying a RADIUS Server Host When configuring a RADIUS server host, you can set different communication parameters, such as the UDP port, the key password, the number of retries, and the timeout. To specify a RADIUS server host and configure its communication parameters, use the following command. ● Enter the host name or IP address of the RADIUS server host.
To view the configuration of RADIUS communication parameters, use the show running-config command in EXEC Privilege mode. Monitoring RADIUS To view information on RADIUS transactions, use the following command. ● View RADIUS transactions to troubleshoot problems. EXEC Privilege mode debug radius Microsoft Challenge-Handshake Authentication Protocol Support for RADIUS Authentication Dell EMC Networking OS supports Microsoft Challenge-Handshake Authentication Protocol (MS-CHAPv2) with RADIUS authentication.
Alternatively, if the user changes authorization level, this change may require that authorization attributes be added or deleted from the user sessions. To overcome these limitations, Dell EMC Networking OS provides RADIUS extension commands in order to enable unsolicited messages to be sent to the NAS. These extension commands provide support for Disconnect Messages (DMs) and Change-ofAuthorization (CoA) packets.
Table 93.
Table 96. CoA EAP/MAB Disable Port (continued) Radius Attribute code Radius Attribute Description Mandatory t=26(vendor-specific);l=length;vendoridentification-attribute;Length=value; Data=”cmd=bounce-host-port” Yes Authorization Attributes 26 Vendor-Specific Table 97. CoA EAP/MAB Bounce Port Radius Attribute code Radius Attribute Description Mandatory NAS Identification Attributes 4 NAS-IP-Address IPv4 address of the NAS. No 95 NAS-IPv6–Address IPv6 address of the NAS.
Table 99. DM AAA Session(s) disconnect (continued) Radius Attribute code Radius Attribute Description Mandatory 5 NAS-Port Port on which session is terminated No t=26(vendor-specific);l=length;vendoridentification-attribute;Length=value; Data=”cmd=disconnect-user” Yes Authorization Attributes 26 Vendor-Specific Error-cause Values It is possible that a Dynamic Authorization Server cannot honor Disconnect Message request or CoA request packets for some reason.
The Invalid Attribute Value Error-Cause is applicable to following scenarios: ○ if the CoA request contains incorrect Vendor-Specific attribute value. ○ if the CoA request contains incorrect NAS-port or calling-station-id values. ● rejects the CoA-Request containing NAS-IP-Address or NAS-IPV6-Address attribute that does not match the NAS with a CoA-Nak; Error-Cause value is “NAS Identification Mismatch” (403).
● responds to a disconnect message containing one or more incorrect attributes values with a Disconnect-NAK; Error-Cause value is “Invalid Attribute Value” (407). ● responds to a disconnect message containing unsupported attributes with DM-Nak; Error-Cause value is “Unsupported Attributes” (401). NOTE: Unsupported attributes are the ones that are not mentioned in the RFC 5176 but present in the disconnect message that is received by the NAS.
1. Enter the following command to configure the dynamic authorization feature: radius dynamic-auth 2. Enter the following command to terminate the 802.1x user session: disconnect-user NAS disconnects the administrative users who are connected through an AAA interface. Dell(conf#)radius dynamic-auth Dell(conf-dynamic-auth#)disconnect-user NAS takes the following actions: ● validates the DM request and the session identification attributes.
To initiate 802.1x session re-authentication, the DAC sends a standard CoA request that contains one or more session identification attributes. NAS uses the calling-station-id or the NAS-port attributes to identify a 802.1x user session. In case of the EAP or MAB users, the MAC address is the calling-station-id of the supplicant and the NAS-port is the interface identifier. If both these attributes are present in the CoA request, NAS retrieves the supplicant connected to the interface.
● discards the packet, if simultaneous requests are received for the same NAS-port or calling-station-id, or both. Disabling 802.1x enabled port Dell EMC Networking OS provides RADIUS extension commands that enables you to disable 802.1x enabled ports. This command administratively shuts down the port causing the termination of the dot1x user session. This command is useful when a port is known to cause issue in the network and needs to be disabled. Before disabling the 802.
Stack failover scenario This section describes the stack failover scenario. ● The NAS stacking module processes the RADIUS dynamic authorization messages only if the role of module is master. ● The NAS standby stacking module processes the retransmitted CoA or DM messages without requiring a chassis reboot, if the master module fails and the standby module becomes the master. Configuring replay protection NAS enables you to configure the replay protection window period.
● TACACS+ Remote Authentication ● Specifying a TACACS+ Server Host For a complete listing of all commands related to TACACS+, refer to the Security chapter in the Dell EMC Networking OS Command Reference Guide. Choosing TACACS+ as the Authentication Method One of the login authentication methods available is TACACS+ and the user’s name and password are sent for authentication to the TACACS hosts specified.
tacacs-server host 10.10.10.10 timeout 1 DellEMC(conf)#tacacs-server key angeline DellEMC(conf)#%RPM0-P:CP %SEC-5-LOGIN_SUCCESS: Login successful for user admin on vty0 (10.11.9.209) %RPM0-P:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success on vty0 ( 10.11.9.209 ) %RPM0-P:CP %SEC-5-LOGOUT: Exec session is terminated for user admin on line vty0 (10.11.9.
To specify multiple TACACS+ server hosts, configure the tacacs-server host command multiple times. If you configure multiple TACACS+ server hosts, Dell EMC Networking OS attempts to connect with them in the order in which they were configured. To view the TACACS+ configuration, use the show running-config tacacs+ command in EXEC Privilege mode. To delete a TACACS+ server host, use the no tacacs-server host {hostname | ip-address} command.
ssh {hostname} [-l username | -p port-number | -v 2}| -c encryption cipher | -m HMAC algorithm hostname is the IP address or host name of the remote device. Enter an IPv4 or IPv6 address in dotted decimal format (A.B.C.D). ● SSH V2 is enabled by default on all the modes. ● Display SSH connection information. EXEC Privilege mode show ip ssh The following example uses the ip ssh server version 2 command to enable SSH version 2 and the show ip ssh command to confirm the setting.
● ● ● ● ● ● ● ● ● ● ip ssh connection-rate-limit : configure the maximum number of incoming SSH connections per minute. ip ssh hostbased-authentication enable : enable host-based authentication for the SSHv2 server. ip ssh password-authentication enable : enable password authentication for the SSH server. ip ssh pub-key-file : specify the file the host-based authentication uses. ip ssh rhostsfile : specify the rhost file the host-based authorization uses.
key-exchange-algorithm : Enter a space-delimited list of key exchange algorithms that will be used by the SSH server. The following key exchange algorithms are available: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 The default key exchange algorithms are the following: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 When FIPS is enabled, the default is diffie-hellman-group14-sha1.
hmac-algorithm: Enter a space-delimited list of keyed-hash message authentication code (HMAC) algorithms supported by the SSH server. The following HMAC algorithms are available: ● hmac-md5 ● hmac-md5-96 ● hmac-sha1 ● hmac-sha1-96 ● hmac-sha2-256 The default list of HMAC algorithm is in the following order: ● hmac-sha2-256 ● hmac-sha1 ● hmac-sha1-96 ● hmac-md5 ● hmac-md5-96 When FIPS is enabled, the default HMAC algorithm is hmac-sha2-256, hmac-sha1, hmac-sha1-96.
cipher-list-: Enter a space-delimited list of ciphers the SSH Client supports. The following ciphers are available. ● 3des-cbc ● aes128-cbc ● aes192-cbc ● aes256-cbc ● aes128-ctr ● aes192-ctr ● aes256-ctr The default cipher list is in the given order: aes256-ctr, aes256-cbc, aes192-ctr, aes192-cbc, aes128-ctr, aes128-cbc, 3des-cbc. Example of Configuring a Cipher List The following example shows you how to configure a cipher list.
To view your SSH configuration, use the show ip ssh command from EXEC Privilege mode. DellEMC(conf)#ip ssh server enable DellEMC(conf)#ip ssh password-authentication enable DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmacsha2-256,hmac-sha2-256-96.
Refer to the first example. 3. Create a list of IP addresses and usernames that are permitted to SSH in a file called rhosts. Refer to the second example. 4. Copy the file shosts and rhosts to the Dell EMC Networking system. 5. Disable password authentication and RSA authentication, if configured CONFIGURATION mode or EXEC Privilege mode no ip ssh password-authentication or no ip ssh rsa-authentication 6. Enable host-based authentication. CONFIGURATION mode ip ssh hostbased-authentication enable 7.
Troubleshooting SSH To troubleshoot SSH, use the following information. You may not bind id_rsa.pub to RSA authentication while logged in via the console. In this case, this message displays:%Error: No username set for this term. Enable host-based authentication on the server (Dell EMC Networking system) and the client (Unix machine). The following message appears if you attempt to log in via SSH and host-based is disabled on the client.
3. Assign an access class. 4. Enter a privilege level. You can assign line authentication on a per-VTY basis; it is a simple password authentication, using an access-class as authorization. Configure local authentication globally and configure access classes on a per-user basis. can assign different access classes to different users by username. Until users attempt to log in, does not know if they will be assigned a VTY line.
Example of Configuring VTY Authorization Based on MAC ACL for the Line (Per MAC Address) DellEMC(conf)#mac access-list standard sourcemac DellEMC(config-std-mac)#permit 00:00:5e:00:01:01 DellEMC(config-std-mac)#deny any DellEMC(conf)# DellEMC(conf)#line vty 0 9 DellEMC(config-line-vty)#access-class sourcemac DellEMC(config-line-vty)#end Role-Based Access Control With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role.
A constrained RBAC model provides for separation of duty and as a result, provides greater security than the hierarchical RBAC model. Essentially, a constrained model puts some limitations around each role’s permissions to allow you to partition of tasks. However, some inheritance is possible. Default command permissions are based on CLI mode (such as configure, interface, router), any specific command settings, and the permissions allowed by the privilege and role commands.
line console 0 login authentication test authorization exec test exec-timeout 0 0 line vty 0 login authentication test authorization exec test line vty 1 login authentication test authorization exec test To enable role-based only AAA authorization, enter the following command in Configuration mode: DellEMC(conf)#aaa authorization role-only System-Defined RBAC User Roles By default, the Dell EMC Networking OS provides 4 system defined user roles. You can create up to 8 additional user roles.
Important Points to Remember Consider the following when creating a user role: ● Only the system administrator and user-defined roles inherited from the system administrator can create roles and user names. Only the system administrator, security administrator, and roles inherited from these can use the "role" command to modify command permissions. The security administrator and roles inherited by security administrator can only modify permissions for commands they already have access to.
line route-map router Line Configuration mode Route map configuration mode Router configuration mode Examples: Deny Network Administrator from Using the show users Command. The following example denies the netadmin role from using the show users command and then verifies that netadmin cannot access the show users command in exec mode. Note that the netadmin role is not listed in the Role access: secadmin,sysadmin, which means the netadmin cannot access the show users command.
DellEMC(conf)#do show role mode configure line Role access:sysadmin Example: Grant and Remove Security Administrator Access to Configure Protocols By default, the system defined role, secadmin, is not allowed to configure protocols. The following example first grants the secadmin role to configure protocols and then removes access to configure protocols.
Configure AAA Authentication for Roles Authentication services verify the user ID and password combination. Users with defined roles and users with privileges are authenticated with the same mechanism. There are six methods available for authentication: radius, tacacs+, local, enable, line, and none. When role-based only AAA authorization is enabled, the enable, line, and none methods are not available.
NOTE: Note that the methods were not applied to the console so the default methods (if configured) are applied there.
The following section shows you how to create an AV pair to allow a user to login from a network access server to have access to commands based on the user’s role. The format to create an AV pair for a user role is Force10avpair= ”shell:role=“ where user-role is a user defined or system-defined role. In the following example, you create an AV pair for a system-defined role, sysadmin. Force10-avpair= "shell:role=sysadmin" In the following example, you create an AV pair for a user-defined role.
Task ID 1, EXEC Accounting record, 00:00:30 Elapsed, service=shell Active accounted actions on tty3, User admin Priv 15 Role sysadmin Task ID 2, EXEC Accounting record, 00:00:26 Elapsed, service=shell Display Information About User Roles This section describes how to display information about user roles and consists of the following topics: ● Displaying User Roles ● Displaying Information About Roles Logged into the Switch ● Displaying Active Accounting Sessions for Roles Displaying User Roles To display
Displaying Information About Users Logged into the Switch To display information on all users logged into the switch, using the show users command in EXEC Privilege mode. The output displays privilege level and/or user role. The mode is displayed at the start of the output and both the privilege and roles for all users is also displayed. If the role is not defined, the system displays "unassigned" .
show ip ssh DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : aes256-ctr,aes256-cbc,aes192-ctr,aes192-cbc,aes128ctr,aes128-cbc,3des-cbc. SSH server macs : hmac-sha2-256,hmac-sha1,hmac-sha1-96,hmac-md5,hmac-md5-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffie-hellman-group1sha1,diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled.
Table 102. Suppressed ICMP message types (continued) ICMPv4 message types Time exceeded (11) IP header bad (12) Timestamp request (13) Timestamp reply (14) Information request (15) Information reply (16) Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMP message type echo request (8). Table 103.
Dell EMC Networking OS Security Hardening The security of a network consists of multiple factors. Apart from access to the device, best practices, and implementing various security features, security also lies with the integrity of the device. If the software itself is compromised, all of the aforementioned methods become ineffective. The Dell EMC Networking OS is enhanced verify whether the OS image and the startup configuration file are altered before loading.
● Use the following command to upgrade the Dell EMC Networking OS and enter the hash value when prompted. EXEC Privilege upgrade system DellEMC# upgrade system tftp://10.16.127.35/FTOS-SE-9.11.0.1 A: Hash Value: e42e2548783c2d5db239ea2fa9de4232 !!!!!!!!!!!!!!... Startup Configuration Verification Dell EMC Networking OS comes with startup configuration verification feature.
After enabling and configuring startup configuration verification, the device verifies the hash checksum of the startup configuration during every reload. DellEMC# verified boot hash startup—config 619A8C1B7A2BC9692A221E2151B9DA9E Configuring the root User Password For added security, you can change the root user password. If you configure the secure-cli command on the system, the Dell EMC Networking OS resets any previously-configured root access password without displaying any warning message.
If you enable the boot access password, the system prompts for a password when you access the GRUB interface. DellEMC(conf)#boot-access password 7 Hg$7^5HMoiY% *********************************************************************** * Warning - boot-access password will enable password protection in * * GRUB. Keep it safe. Forgetting this password and the CLI password * * may result in switch becoming inaccessible.
51 Service Provider Bridging Service provider bridging provides the ability to add a second VLAN ID tag in an Ethernet frame and is referred to as VLAN stacking in the Dell EMC Networking OS. Topics: • • • • • VLAN Stacking VLAN Stacking Packet Drop Precedence Dynamic Mode CoS for VLAN Stacking Layer 2 Protocol Tunneling Provider Backbone Bridging VLAN Stacking VLAN stacking, also called Q-in-Q, is defined in IEEE 802.1ad — Provider Bridges, which is an amendment to IEEE 802.
Figure 119. VLAN Stacking in a Service Provider Network Important Points to Remember ● Interfaces that are members of the Default VLAN and are configured as VLAN-Stack access or trunk ports do not switch untagged traffic. To switch traffic, add these interfaces to a non-default VLAN-Stack-enabled VLAN. ● Dell EMC Networking cautions against using the same MAC address on different customer VLANs, on the same VLAN-Stack VLAN.
Related Configuration Tasks ● ● ● ● Configuring the Protocol Type Value for the Outer VLAN Tag Configuring Dell EMC Networking OS Options for Trunk Ports Debugging VLAN Stacking VLAN Stacking in Multi-Vendor Networks Creating Access and Trunk Ports To create access and trunk ports, use the following commands. ● Access port — a port on the service provider edge that directly connects to the customer. An access port may belong to only one service provider VLAN.
2 3 4 5 6 Inactive Inactive Inactive Inactive Active DellEMC# M Po1(Te 3/14-15) M Te 3/13 Configuring the Protocol Type Value for the Outer VLAN Tag The tag protocol identifier (TPID) field of the S-Tag is user-configurable. To set the S-Tag TPID, use the following command. ● Select a value for the S-Tag TPID. CONFIGURATION mode vlan-stack protocol-type The default is 9100. To display the S-Tag TPID for a VLAN, use the show running-config command from EXEC privilege mode.
Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM * 1 100 101 103 Status Inactive Inactive Inactive Inactive Description Q Ports U Te 1/1 T Te 1/1 M Te 1/1 Debugging VLAN Stacking To debug VLAN stacking, use the following command. ● Debug the internal state and membership of a VLAN and its ports. debug member The port notations are as follows: ● MT — stacked trunk ● MU — stacked access port ● T — 802.1Q trunk port ● U — 802.
system is able to differentiate between 0x8100 and untagged traffic and maps each to the appropriate VLAN, as shown by the packet originating from Building A. Therefore, a mismatched TPID results in the port not differentiating between tagged and untagged traffic. Figure 120.
Figure 121.
Figure 122. Single and Double-Tag TPID Mismatch The following table details the outcome of matched and mismatched TPIDs in a VLAN-stacking network with the S-Series. Table 104. Behaviors for Mismatched TPID Network Position Incoming Packet TPID System TPID Match Type Pre-Version 8.2.1.0 Version 8.2.1.
Table 104. Behaviors for Mismatched TPID (continued) Network Position Egress Access Point Incoming Packet TPID System TPID Match Type Pre-Version 8.2.1.0 Version 8.2.1.
Precedence Description Green High-priority packets that are the least preferred to be dropped. Yellow Lower-priority packets that are treated as best-effort. Red Lowest-priority packets that are always dropped (regardless of congestion status). ● Honor the incoming DEI value by mapping it to an Dell EMC Networking OS drop precedence. INTERFACE mode dei honor {0 | 1} {green | red | yellow} You may enter the command once for 0 and once for 1. Packets with an unmapped DEI value are colored green.
Figure 123. Statically and Dynamically Assigned dot1p for VLAN Stacking When configuring Dynamic Mode CoS, you have two options: ● Mark the S-Tag dot1p and queue the frame according to the original C-Tag dot1p. In this case, you must have other dot1p QoS configurations; this option is classic dot1p marking. ● Mark the S-Tag dot1p and queue the frame according to the S-Tag dot1p.
interface TenGigabitEthernet 1/21 no ip address switchport vlan-stack access vlan-stack dot1p-mapping c-tag-dot1p 0-3 sp-tag-dot1p 7 service-policy input in layer2 no shutdown Mapping C-Tag to S-Tag dot1p Values To map C-Tag dot1p values to S-Tag dot1p values and mark the frames accordingly, use the following commands. 1. Allocate CAM space to enable queuing frames according to the C-Tag or the S-Tag.
Figure 124. VLAN Stacking without L2PT You might need to transport control traffic transparently through the intermediate network to the other region. Layer 2 protocol tunneling enables BPDUs to traverse the intermediate network by identifying frames with the Bridge Group Address, rewriting the destination MAC to a user-configured non-reserved address, and forwarding the frames.
Figure 125. VLAN Stacking with L2PT Implementation Information ● L2PT is available for STP, RSTP, MSTP, and PVST+ BPDUs. ● No protocol packets are tunneled when you enable VLAN stacking. ● L2PT requires the default CAM profile. Enabling Layer 2 Protocol Tunneling To enable Layer 2 protocol tunneling, use the following command. 1. Verify that the system is running the default CAM profile. Use this CAM profile for L2PT. EXEC Privilege mode show cam-profile 2.
INTERFACE VLAN mode protocol-tunnel stp Specifying a Destination MAC Address for BPDUs By default, Dell EMC Networking OS uses a Dell EMC Networking-unique MAC address for tunneling BPDUs. You can configure another value. To specify a destination MAC address for BPDUs, use the following command. ● Overwrite the BPDU with a user-specified destination MAC address when BPDUs are tunneled across the provider network.
originally specified in 802.1Q. Only bridges in the service provider network use this destination MAC address so these bridges treat BPDUs originating from the customer network as normal data frames, rather than consuming them. The same is true for GARP VLAN registration protocol (GVRP). 802.
52 sFlow sFlow is a standard-based sampling technology embedded within switches and routers which is used to monitor network traffic. It is designed to provide traffic monitoring for high-speed networks with many switches and routers.
● If the global sampling rate is non-default, for example 256, and if the sampling rate is not configured on the interface, the sampling rate of the interface is the global non-default sampling rate, that is, 256. To avoid the back-off, either increase the global sampling rate or configure all the line card ports with the desired sampling rate even if some ports have no sFlow configured.
Te 1/1: configured rate 16384, actual rate 16384 DellEMC# If you did not enable any extended information, the show output displays the following (shown in bold).
Example of viewing the sflow max-header-size extended on an Interface Mode DellEMC#show sflow interface tengigabitethernet 1/1 Te 1/1 sFlow type :Ingress Configured sampling rate :16384 Actual sampling rate :16384 Counter polling interval :20 Extended max header size :256 Samples rcvd from h/w :0 Example of the show running-config sflow Command DellEMC#show running-config sflow ! sflow collector 100.1.1.12 agent-addr 100.1.1.
Displaying Show sFlow on an Interface To view sFlow information on a specific interface, use the following command. ● Display sFlow configuration information and statistics on a specific interface. EXEC mode show sflow interface interface-name The following example shows the show sflow interface command.
Changing the Polling Intervals The sflow polling-interval command configures the polling interval for an interface in the maximum number of seconds between successive samples of counters sent to the collector. This command changes the global default counter polling (20 seconds) interval. You can configure an interface to use a different polling interval. To configure the polling intervals globally (in CONFIGURATION mode) or by interface (in INTERFACE mode), use the following command.
The bold line shows that extended sFlow settings are enabled on all three types. DellEMC#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header size: 128 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.1, Agent IP addr: 1.1.1.
Table 106. Extended Gateway Summary (continued) IP SA IP DA srcAS and srcPeerAS dstAS and dstPeerAS Description Version 7.8.1.0 allows extended gateway information in cases where the source and destination IP addresses are learned by different routing protocols, and for cases where is source is reachable over ECMP. BGP BGP Exported Exported Extended gateway data is packed.
53 Simple Network Management Protocol (SNMP) The Simple Network Management Protocol (SNMP) is designed to manage devices on IP networks by monitoring device operation, which might require administrator intervention. NOTE: On Dell EMC Networking routers, standard and private SNMP management information bases (MIBs) are supported, including all Get and a limited number of Set operations (such as set vlan and copy cmd).
Protocol Overview Network management stations use SNMP to retrieve or alter management data from network elements. A datum of management information is called a managed object; the value of a managed object can be static or variable. Network elements store managed objects in a database called a management information base (MIB). MIBs are hierarchically structured and use object identifiers to address managed objects, but managed objects also have a textual name called an object descriptor.
You cannot modify the FIPS mode if SNMPv3 users are already configured and present in the system. An error message is displayed if you attempt to change the FIPS mode by using the fips mode enable command in Global Configuration mode. You can enable or disable FIPS mode only if SNMPv3 users are not previously set up. If previously configured users exist on the system, you must delete the existing users before you change the FIPS mode.
SNMP version 3 (SNMPv3) is a user-based security model that provides password authentication for user security and encryption for data security and privacy. Three sets of configurations are available for SNMP read/write operations: no password or privacy, password privileges, password and privacy privileges. You can configure a maximum of 16 users even if they are in different groups.
CONFIGURATION mode snmp-server user name group-name 3 noauth auth md5 auth-password ● Configure an SNMP group (password privileges only). CONFIGURATION mode snmp-server group groupname {oid-tree} auth read name write name ● Configure an SNMPv3 view. CONFIGURATION mode snmp-server view view-name 3 noauth {included | excluded} NOTE: To give a user read and write privileges, repeat this step for each privilege type. ● Configure an SNMP group (with password or privacy privileges).
snmpwalk -v version -c community agent-ip {identifier.instance | descriptor.instance} In the following example, the value “4” displays in the OID before the IP address for IPv4. For an IPv6 IP address, a value of “16” displays. > snmpget -v 2c -c mycommunity 10.11.131.161 sysUpTime.0 DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (32852616) 3 days, 19:15:26.16 > snmpget -v 2c -c mycommunity 10.11.131.161 .1.3.6.1.2.1.1.3.0 The following example shows reading the value of the next managed object.
You may use up to 55 characters. The default is None. ● (From a management station) Identify the system manager along with this person’s contact information (for example, an email address or phone number). CONFIGURATION mode snmpset -v version -c community agent-ip sysContact.0 s “contact-info” You may use up to 55 characters. The default is None. ● (From a management station) Identify the physical location of the system (for example, San Jose, 350 Holger Way, 1st floor lab, rack A1-1).
snmp linkdown snmp linkup PORT_LINKDN:changed interface state to down:%d PORT_LINKUP:changed interface state to up:%d Enabling a Subset of SNMP Traps You can enable a subset of Dell EMC Networking enterprise-specific SNMP traps using one of the following listed command options. To enable a subset of Dell EMC Networking enterprise-specific SNMP traps, use the following command. ● Enable a subset of SNMP traps.
Enable VLT traps. vrrp Enable VRRP state change traps xstp %SPANMGR-5-STP_NEW_ROOT: New Spanning Tree Root, Bridge ID Priority 32768, Address 0001.e801.fc35. %SPANMGR-5-STP_TOPOLOGY_CHANGE: Bridge port TenGigabitEthernet 1/8 transitioned from Forwarding to Blocking state. %SPANMGR-5-MSTP_NEW_ROOT_BRIDGE: Elected root bridge for instance 0. %SPANMGR-5-MSTP_NEW_ROOT_PORT: MSTP root changed to port Te 1/8 for instance 0. My Bridge ID: 40960:0001.e801.fc35 Old Root: 40960:0001.e801.fc35 New Root: 32768:00d0.
CONFIGURATION MODE snmp-server enable traps snmp syslog-unreachable To enable an SNMP agent to send a trap when the syslog server resumes connectivity, enter the following command: CONFIGURATION MODE snmp-server enable traps snmp syslog-reachable Table 108. List of Syslog Server MIBS that have read access MIB Object OID Object Values Description dF10SysLogTraps 1.3.6.1.4.1.6027.3.30.1.1 1 = reachable2 = unreachable Specifies whether the syslog server is reachable or unreachable.
Table 109. MIB Objects for Copying Configuration Files via SNMP (continued) MIB Object OID Object Values Description 2 = running-config ● If copySrcFileType is running-config or startupconfig, the default copySrcFileLocation is flash. ● If copySrcFileType is a binary file, you must also specify copySrcFileLocation and copySrcFileName. 3 = startup-config copySrcFileLocation .1.3.6.1.4.1.6027.3.5.1.1.1.1.
Table 109. MIB Objects for Copying Configuration Files via SNMP (continued) MIB Object OID Object Values Description ● If you specify copyUserName, you must also specify copyUserPassword. copyUserPassword .1.3.6.1.4.1.6027.3.5.1.1.1.1.10 Password for the server. Password for the FTP, TFTP, or SCP server. Copying a Configuration File To copy a configuration file, use the following commands. NOTE: In UNIX, enter the snmpset command for help using the following commands. Place the f10-copy-config.
The following examples show the command syntax using MIB object names and the same command using the object OIDs. In both cases, a unique index number follows the object. The following example shows copying configuration files using MIB object names. > snmpset -v 2c -r 0 -t 60 -c private -m ./f10-copy-config.mib 10.10.10.10 copySrcFileType.101 i 2 copyDestFileType.101 i 3 FTOS-COPY-CONFIG-MIB::copySrcFileType.101 = INTEGER: runningConfig(2) FTOS-COPY-CONFIG-MIB::copyDestFileType.
Copying the Startup-Config Files to the Server via TFTP To copy the startup-config to the server via TFTP from the UNIX machine, use the following command. NOTE: Verify that the file exists and its permissions are set to 777. Specify the relative path to the TFTP root directory. ● Copy the startup-config to the server via TFTP from the UNIX machine. snmpset -v 2c -c public -m ./f10-copy-config.mib force10system-ip-address copySrcFileType.index i 3 copyDestFileType.index i 1 copyDestFileName.
Table 110. Additional MIB Objects for Copying Configuration Files via SNMP (continued) MIB Object OID Values Description 6 = timeout 7 = unknown copyEntryRowStatus .1.3.6.1.4.1.6027.3.5.1.1.1.1.15 Row status Specifies the state of the copy operation. Uses CreateAndGo when you are performing the copy. The state is set to active when the copy is completed. Obtaining a Value for MIB Objects To obtain a value for any of the MIB objects, use the following command. ● Get a copy-config MIB object value.
Table 111. MIB Objects for Displaying Reason for Last System Reboot (continued) MIB Object OID Description dellNetProcessorResetTime 1.3.6.1.4.1.6027.3.26.1.4.3.1.8 This is the table that contains the timestamp. Viewing the Reason for Last System Reboot Using SNMP ● To view the reason for last system reboot using SNMP, you can use any one of the applicable SNMP commands: The following example shows a sample output of the snmpwalk command to view the last reset reason.
MIB Support to Display the Available Memory Size on Flash Dell EMC Networking provides more MIB objects to display the available memory size on flash memory. The following table lists the MIB object that contains the available memory size on flash memory. Table 113. MIB Objects for Displaying the Available Memory Size on Flash via SNMP MIB Object OID Description chStackUnitFlashUsageUtil 1.3.6.1.4.1.6027.3.10.1.2.9.1.6 Contains flash memory usage in percentage.
Viewing the Software Core Files Generated by the System ● To view the software core files generated by the system, use the following command. snmpwalk -v2c -c public 192.168.60.120 .1.3.6.1.4.1.6027.3.10.1.2.10 enterprises.6027.3.10.1.2.10.1.1.1.1 = 1 enterprises.6027.3.10.1.2.10.1.1.1.2 = 2 enterprises.6027.3.10.1.2.10.1.1.1.3 = 3 enterprises.6027.3.10.1.2.10.1.1.2.1 = 1 enterprises.6027.3.10.1.2.10.1.2.1.1 = "/CORE_DUMP_DIR/flashmntr.core.gz" enterprises.6027.3.10.1.2.10.1.2.1.
SNMPv2-SMI::enterprises.6027.3.27.1.3.1.16.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.17.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.18.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.19.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.20.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.21.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.22.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.23.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.24.2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.25.
.1.3.6.1.4.1.6027.3.26.1.4.8.1.5.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.5.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.5.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.5.4 .1.3.6.1.4.1.6027.3.26.1.4.8.1.6.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.6.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.6.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.6.
MIB Support to ECMP Group Count Dell EMC Networking OS provides MIB objects to display the information of the ECMP group count information. The following table lists the related MIB objects: Table 118. MIB Objects to display ECMP Group Count MIB Object OID Description dellNetInetCidrECMPGrpMax 1.3.6.1.4.1.6027.3.9.1.6 Total CAM for ECMP group. dellNetInetCidrECMPGrpUsed 1.3.6.1.4.1.6027.3.9.1.7 Used CAM for ECMP group. dellNetInetCidrECMPGrpAvl 1.3.6.1.4.1.6027.3.9.1.
INTEGER: 2097157 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.100.100.100.0.24.1.4.10.1.1.1.1.4.10.1.1.1 = INTEGER: 2098693 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.100.100.100.0.24.1.4.20.1.1.1.1.4.20.1.1.1 = INTEGER: 1258296320 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.100.100.100.0.24.1.4.30.1.1.1.1.4.30.1.1.1 = INTEGER: 1275078656 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.10.1.1.0.24.0.0.0.0 = "" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.10.1.1.1.32.1.4.10.1.1.1.1.4.10.1.1.
SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.70.70.70.0.24.0.0.0.0 = STRING: "CP" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.70.70.70.1.32.1.4.127.0.0.1.1.4.127.0.0.1 = STRING: "CP" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.70.70.70.2.32.1.4.70.70.70.2.1.4.70.70.70.2 = STRING: "Fo 1/1/1" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.80.80.80.0.24.1.4.10.1.1.1.1.4.10.1.1.1 = STRING: "Fo 1/4/1" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.80.80.80.0.24.1.4.20.1.1.1.1.4.20.1.1.
SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.100.100.100.0.24.1.4.10.1.1.1.1.4.10.1.1.1 = Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.100.100.100.0.24.1.4.20.1.1.1.1.4.20.1.1.1 = Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.100.100.100.0.24.1.4.30.1.1.1.1.4.30.1.1.1 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.6.0 = Gauge32: 2048 SNMPv2-SMI::enterprises.6027.3.9.1.7.0 = Gauge32: 1 SNMPv2-SMI::enterprises.6027.3.9.1.8.
Table 120. MIB Objects for LAG MIB Object OID Description lagMIB 1.2.840.10006.300.43 Contains information about link aggregation module for managing 802.3ad. lagMIBObjects 1.2.840.10006.300.43.1 dot3adAgg 1.2.840.10006.300.43.1.1 dot3adAggTable 1.2.840.10006.300.43.1.1.1 Contains information about every Aggregator that is associated with a system. dot3adAggEntry 1.2.840.10006.300.43.1.1.1.1 Contains a list of Aggregator parameters and indexed by the ifIndex of the Aggregator.
Table 120. MIB Objects for LAG (continued) MIB Object OID Description dot3adAggPortListEntry 1.2.840.10006.300.43.1.1.2.1 Contains a list of ports associated with a given Aggregator and indexed by the ifIndex of the Aggregator. dot3adAggPortListPorts 1.2.840.10006.300.43.1.1.2.1.1 Contains a complete set of ports currently associated with the Aggregator. Viewing the LAG MIB ● To view the LAG MIB generated by the system, use the following command. snmpbulkget -v 2c -c LagMIB 10.16.148.157 1.2.840.
snmpwalk -v2c -c mycommunity 10.16.150.83 1.0.8802.1.1.2.1.4 iso.0.8802.1.1.2.1.4.1.1.6.0.2113029.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161092.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161605.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4209668.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4210181.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.9437185.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.7.0.2113029.2 = STRING: "fortyGigE 1/50" iso.0.8802.1.1.2.1.4.1.1.7.0.3161092.
snmpwalk -v2c -c public 10.16.150.83 1.0.8802.1.1.2.1.4.4.1.4 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.1.133 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.2.134 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.3.135 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.4.136 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.5.137 = = = = = STRING: STRING: STRING: STRING: STRING: "Dell" "Dell" "Dell" "Dell" "Dell" snmpget -v2c -c public 10.16.150.102 1.0.8802.1.1.2.1.4.4.1.4.0.1048580.2.0.1.232.16.1 iso.0.
Table 124. Global MIB Objects for Port Security (continued) MIB Object OID Access or Permission Description dellNetGlobalResetViolationSt atus 1.3.6.1.4.1.6027.3.31.1.1.4 read-write Resets the violation status (Errdisabled state) of all violated interfaces based on the specified type (MAC limit or station move violation). MIB support for interface level port security The MIB table dellNetPortSecIfConfigTable is used to achieve port security feature (MAC address learning limit) on an interface.
Enabling and viewing SNMP for port security To enable or view DELL-NETWORKING-PORT-SECURITY-MIB, configure snmp-server in read-write mode using the snmpserver community public rw command. You can enable the port security feature on the Dell EMC Networking OS using the snmpset command. Also, you can view if the port security feature is enabled or disabled using the snmpwalk command. To configure dellNetPortSecIfSecureMacLimit as 100 on an interface whose ifIndex is 2101252, use the following command.
To retrieve the static MAC address configured, use the following command. snmpget -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.2.1.4.6.0.0.0.0.17.17.100.2101252 MIB objects for configuring MAC addresses This section describes about the MIB table dellNetPortSecSecureMacAddrTable that contains the MAC database of the system. The table is indexed by the following parameters: ● MAC Address (Octet string of length 6 and MAC address ( in decimal) as value ● VLAN ID Table 127.
SNMPv2-SMI::mib-2.17.7.1.4.3.1.1.
[Unix system output] > snmpget -v2c -c mycommunity 10.11.131.185 .1.3.6.1.2.1.17.7.1.4.3.1.2.1107787786 SNMPv2-SMI::mib-2.17.7.1.4.3.1.2.1107787786 = Hex-STRING: 40 00 00 00 00 00 00 00 00 00 00 The value 40 is in the first set of 7 hex pairs, indicating that these ports are in Stack Unit 1. The hex value 40 is 0100 0000 in binary. As described, the left-most position in the string represents Port 1.
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SNMPv2-SMI::mib-2.17.7.1.4.3.1.4.
Fetch Dynamic MAC Entries using SNMP Dell EMC Networking supports the RFC 1493 dot1d table for the default VLAN and the dot1q table for all other VLANs. NOTE: The 802.1q Q-BRIDGE MIB defines VLANs regarding 802.1d, as 802.1d itself does not define them. As a switchport must belong a VLAN (the default VLAN or a configured VLAN), all MAC address learned on a switchport are associated with a VLAN. For this reason, the Q-Bridge MIB is used for MAC address query.
Example of Fetching MAC Addresses Learned on a Port-Channel Using SNMP Use dot3aCurAggFdbTable to fetch the learned MAC address of a port-channel. The instance number is the decimal conversion of the MAC address concatenated with the port-channel number.
to be mapped to a community map. A new CLI command, snmp context, under BGP context, has been introduced to perform this function. To map the context to a VRF instance for SNMPv2c, follow these steps: 1. Create a community and map a VRF to it. Create a context and map the context and community, to a community map.
Example of SNMP Walk Output for BGP timer configured for vrf1 (SNMPv2c) snmpwalk -v 2c -c vrf1 10.16.131.125 1.3.6.1.4.1.6027.20.1.2.3 SNMPv2-SMI::enterprises.6027.20.1.2.3.1.1.1.0.1.20.1.1.2.1.20.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.1.1.2.0.1.20.1.1.2.1.20.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.1.0.1.20.1.1.2.1.20.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.2.0.1.20.1.1.2.1.20.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.3.0.1.20.1.1.2.1.20.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.
Example of Viewing Status of Learned MAC Addresses dot3aCurAggVlanId SNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.1.1.0.0.0.0.0.1.1 dot3aCurAggMacAddr SNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.2.1.0.0.0.0.0.1.1 01 dot3aCurAggIndex SNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.3.1.0.0.0.0.0.1.1 dot3aCurAggStatus SNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.4.1.0.0.0.0.0.1.1 status inactive = INTEGER: 1 = Hex-STRING: 00 00 00 00 00 = INTEGER: 1 = INTEGER: 1 << Status active, 2 – Layer 3 LAG does not include this support.
Table 130. List of Syslog Server MIBS that have read access MIB Object OID Object Values Description dF10SysLogTraps 1.3.6.1.4.1.6027.3.30.1.1 1 = reachable2 = unreachable Specifies whether the syslog server is reachable or unreachable. The following example shows the SNMP trap that is sent when connectivity to the syslog server is lost: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (19738) 0:03:17.38 SNMPv2MIB::snmpTrapOID.0 = OID: SNMPv2SMI::enterprises.6027.3.30.1.1.1 SNMPv2-SMI::enterprises.
Example of SNMP Output for Transceiver Monitoring Dell $ snmpwalk -v1 -c public 10.16.150.210 1.3.6.1.4.1.6027.3.11.1.3.1.1 | grep 2106373 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.1.2113540 = STRING: "stack-unit-1 fixedmodule-5 port-1" SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.2.2113540 = STRING: "Te 1/5/1" SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.3.2113540 = INTEGER: 1 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.4.2113540 = STRING: "10GBASE-SR" SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.5.
Configuring SNMP context name To configure the SNMP context name for OSPFv3 module, use the following command. ● Configure the SNMP context-name. CONF-IPV6-ROUTER-OSPF mode SNMP context {context-name} ● Verify SNMP context configuration. EXEC Privilege show running-config ospf Sample SNMP context configuration: DellEMC(conf-ipv6-router_ospf)#snmp context ospf1 DellEMC>show runnig-config ospf ! ipv6 router ospf 10 router-id 10.10.10.
54 Stacking Using the Dell EMC Networking OS stacking feature, you can interconnect multiple switch units with stacking ports or front end user ports. The stack becomes manageable as a single switch through the stack management unit. The system accepts Unit ID numbers from 1 to 6 and it supports stacking up to six units.
Stack Master Election The stack elects a master and standby unit at bootup time based on two criteria. ● Unit priority — User-configurable. The range is from 1 to 14. A higher value (14) means a higher priority. The default is 0. By removing the stack-unit priority using the no stack-unit priority command, you can set the priority back to the default value of zero. The unit with the highest priority is elected the master management unit; the unit with the second highest priority is elected the standby unit.
2 2 down UNKNOWN down 0 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed -----------------------------------------------------------------------------------2 1 up up 10031 up 10031 2 2 up up 10031 up 10031 2 3 up up 10134 up 10031 Speed in RPM -- Unit 3 -Unit Type : Member Unit Status : online Next Boot : online Required Type : S4048-ON - 54-port TE/FG (SK-ON) Current Type : S4048-ON - 54-port TE/FG (SK-ON) Master priority : 5 Hardware Rev : 2.
Virtual IP You can manage the stack using a single IP, known as a virtual IP, that is retained in the stack even after a failover. The virtual IP address is used to log in to the current master unit of the stack. Both IPv4 and IPv6 addresses are supported as virtual IPs. Use the following command to configure a virtual IP: Dell(conf)#virtual-ip {ip-address | ipv6–address | dhcp} Failover Roles If the stack master fails (for example, is powered off), it is removed from the stack topology.
2 Member not present 3 Member not present 4 Member not present 5 Member not present 6 Member not present 7 Member not present [output omitted] Stack#show system stack-unit 1 | grep priority Master priority : 0 Stack#show system stack-unit 2 | grep priority Master priority : 0 Example of Adding a Standalone with a Lower MAC Address and Equal Priority to a Stack Stacking LAG When multiple links are used between stack units, Dell EMC Networking OS automatically bundles them in a stacking LAG to provide aggreg
High Availability on Stacks Stacks have master and standby management units analogous to Dell EMC Networking route processor modules (RPM). The master unit synchronizes the running configuration and protocol states so that the system fails over in the event of a hardware or software fault on the master unit. In such an event, or when the master unit is removed, the standby unit becomes the stack manager and Dell EMC Networking OS elects a new standby unit.
clear copy delete dir disable enable exit format fsck pwd rename reset show ssh-peer-stack-unit start telnet-peer-stack-unit terminal upload Dell(standby)# Reset functions Copy from one file to another Delete a file List files on a filesystem Turn off privileged commands Turn on privileged commands Exit from the EXEC Format a filesystem Filesystem check utility Display current working directory Rename a file Reset selected card Show running system information Open a SSH connection to the peer stack-unit St
Stacking Installation Tasks The following are the stacking installation tasks. ● Create a Stack ● Add Units to an Existing Stack ● Split a Stack Create a Stack Stacking is enabled on the device using the front end ports. No configuration is allowed on front end ports used for stacking. Stacking can be made between 10G ports of two units or 40G ports of two units. The stack links between the two units are grouped into a single LAG.
● if the system check fails, a message such as a hardware incompatibility message or incompatible uboot version is generated. If the unit is placed in a card problem state, the management unit also generates an SNMP trap. ● if the software version of the new unit predates Dell EMC Networking OS version 8.3.12.
CONFIGURATION mode stack-unit stack—unit—number priority priority 5. Assign a stack group for each unit. CONFIGURATION mode stack-unit stack-unit—id stack-group stack-group—id Begin with the first port on the management unit. Next, configure both ports on each subsequent unit. Finally, return to the management unit and configure the last port. (refer to the following example.) 6. Connect the units using stacking cables. NOTE: The device does not require special stacking cables.
Reload each unit in the stack. After the reload is complete, the four units come up as a stack with unit 1 as the management unit, unit 2 as the standby unit, and the remaining units as stack-members. All units in the stack can be accessed from the management unit. NOTE: Before executing show commands, you must wait for 10 to 15 seconds for the download-agent process to start. To view the stack unit information after the reload, use the show system brief command.
(Gb/s) Status Status Group -----------------------------------------------------------------1/1 1/1 10 up up 1/2 1/2 10 up up 1/3 1/3 10 up up 1/4 1/4 10 up up Add Units to an Existing Stack You can add units to an existing stack in one of three ways. ● By manually assigning a new unconfigured unit a position in an existing stack. ● By adding a configured unit to an existing stack. ● By merging two stacks.
5 6 Member Member not present not present The following example shows adding a stack unit with a conflicting stack number (after).
● If the stack has been provisioned for the stack number that is assigned to the new unit, the pre-configured provisioning must match the switch type. If there is a conflict between the provisioned switch type and the new unit, a mismatch error message is displayed. Merge Two Stacks You may merge two stacks while they are powered and online. To merge two stacks, connect one stack to the other using user port cables from the front end user portusing the mini-SAS cables from the stacking ports.
WARNING: Interface configuration for current unit will be lost! Proceed to renumber [confirm yes/no]: yes Creating a Virtual Stack Unit on a Stack Use virtual stack units to configure ports on the stack before adding a new unit. ● Create a virtual stack unit. CONFIGURATION mode stack-unit stack-unit-number provision S4048–ON Displaying Information about a Stack To display information about the stack, use the following command.
1 1 2 3 up up up up 10031 10031 up up 10031 10031 Speed in RPM -- Unit 2 -Unit Type : Standby Unit Status : online Next Boot : online Required Type : S4048-ON - 54-port TE/FG (SK-ON) Current Type : S4048-ON - 54-port TE/FG (SK-ON) Master priority : 10 Hardware Rev : 2.
The following is an example of the show system brief command to view the stack summary information.
in the stack, the system selects a new standby unit based on the unit priority using the same algorithm used when the stack was initially created. When the failed unit recovers, it takes the next available role, usually that of a stack member. ● Influence the selection of the stack management units.
Displaying the Status of Stacking Ports To display the status of the stacking ports, including the topology, use the following command. ● Display the stacking ports.
The following example shows three switches stacked together in a daisy chain topology.
-- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports ------------------------------------------------------0 Management online S4810 S4810 8-3-7-13 64 1 Member not present S4810 2 Member not present 3 Standby online S4810 S4810 8-3-7-13 64 4 Member not present 5 Member not present 6 Member not present 7 Member not present 8 Member not present 9 Member not present 10 Member not present 11 Member not present NOTE: Each unit in the stack has a stack number that is either assigned by you or Dell EMC
10:55:20: %STKUNIT1-M:CP %KERN-2-INT: Error: Stack Port 50 has flapped 5 times w ithin 10 seconds.Shutting down this stack port now. 10:55:20: %STKUNIT1-M:CP %KERN-2-INT: Error: Please check the stack cable/module and power-cycle the stack. ---------------------STANDBY UNIT-------------------------------10:55:18: %STKUNIT1-M:CP %KERN-2-INT: Error: Stack Port 50 has flapped 5 times within 10 seonds.Shutting down this stack port now.
55 Storm Control Storm control allows you to control unknown-unicast, muticast, and broadcast traffic on Layer 2 and Layer 3 physical interfaces. Dell EMC Networking Operating System (OS) Behavior: Dell EMC Networking OS supports unknown-unicast, muticast, and broadcast control for Layer 2 and Layer 3 traffic. Dell EMC Networking OS Behavior: The minimum number of packets per second (PPS) that storm control can limit on the device is two.
● Configure the packets per second of multicast traffic allowed on C-Series or S-Series interface (ingress only) network only. INTERFACE mode storm-control multicast packets_per_second in ● Shut down the port if it receives the PFC/LLFC packets more than the configured rate. INTERFACE mode storm-control pfc-llfc pps in shutdown NOTE: PFC/LLFC storm control enabled interface disables the interfaces if it receives continuous PFC/LLFC packets.
56 Spanning Tree Protocol (STP) The spanning tree protocol (STP) is supported on Dell EMC Networking OS.
Related Configuration Tasks ● ● ● ● ● ● ● ● Adding an Interface to the Spanning Tree Group Modifying Global Parameters Modifying Interface STP Parameters Enabling PortFast Prevent Network Disruptions with BPDU Guard STP Root Guard Enabling SNMP Traps for Root Elections and Topology Changes Configuring Spanning Trees as Hitless Important Points to Remember ● STP is disabled by default. ● The Dell EMC Networking OS supports only one spanning tree instance (0).
Configuring Interfaces for Layer 2 Mode All interfaces on all switches that participate in spanning tree must be in Layer 2 mode and enabled. Figure 129. Example of Configuring Interfaces for Layer 2 Mode To configure and enable the interfaces for Layer 2, use the following command. 1. If the interface has been assigned an IP address, remove it. INTERFACE mode no ip address 2. Place the interface in Layer 2 mode. INTERFACE switchport 3. Enable the interface.
no shutdown DellEMC(conf-if-te-1/1)# Enabling Spanning Tree Protocol Globally Enable the spanning tree protocol globally; it is not enabled by default. When you enable STP, all physical, VLAN, and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the Spanning Tree topology. ● Only one path from any bridge to any other bridge participating in STP is enabled. ● Bridges block a redundant path by disabling one of the link ports. Figure 130.
To view the spanning tree configuration and the interfaces that are participating in STP, use the show spanning-tree 0 command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output. R2#show spanning-tree 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, address 0001.e826.ddb7 Configured hello time 2, max age 20, forward delay 15 Current root has priority 32768, address 0001.e80d.
Modifying Global Parameters You can modify the spanning tree parameters. The root bridge sets the values for forward-delay, hello-time, and max-age and overwrites the values set on other bridges participating in STP. NOTE: Dell EMC Networking recommends that only experienced network administrators change the spanning tree parameters. Poorly planned modification of the spanning tree parameters can negatively affect network performance. The following table displays the default values for STP. Table 133.
Modifying Interface STP Parameters You can set the port cost and port priority values of interfaces in Layer 2 mode. ● Port cost — a value that is based on the interface type. The greater the port cost, the less likely the port is selected to be a forwarding port. ● Port priority — influences the likelihood that a port is selected to be a forwarding port in case that several ports have the same port cost. The default values are listed in Modifying Global Parameters.
Prevent Network Disruptions with BPDU Guard Configure the Portfast (and Edgeport, in the case of RSTP, PVST+, and MSTP) feature on ports that connect to end stations. End stations do not generate BPDUs, so ports configured with Portfast/ Edgport (edgeports) do not expect to receive BDPUs. If an edgeport does receive a BPDU, it likely means that it is connected to another part of the network, which can negatively affect the STP topology.
Figure 131. Enabling BPDU Guard Dell EMC Networking OS Behavior BPDU guard: ● is used on edgeports and blocks all traffic on edgeport if it receives a BPDU. ● drops the BPDU after it reaches the RP and generates a console message. Example of Blocked BPDUs DellEMC(conf-if-te-1/7)#do show spanning-tree rstp brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e805.fb07 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e85d.
Selecting STP Root The STP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it becomes the root bridge. You can also specify that a bridge is the root or the secondary root. To change the bridge priority or specify that a bridge is the root or secondary root, use the following command. ● Assign a number as the bridge priority or designate it as the root or secondary root.
Figure 132. STP Root Guard Prevents Bridging Loops Configuring Root Guard Enable STP root guard on a per-port or per-port-channel basis. Dell EMC Networking OS Behavior: The following conditions apply to a port enabled with STP root guard: ● Root guard is supported on any STP-enabled port or port-channel interface except when used as a stacking port.
To verify the STP root guard configuration on a port or port-channel interface, use the show spanning-tree 0 guard [interface interface] command in a global configuration mode. Enabling SNMP Traps for Root Elections and Topology Changes To enable SNMP traps individually or collectively, use the following commands. ● Enable SNMP traps for spanning tree state changes. snmp-server enable traps stp ● Enable SNMP traps for RSTP, MSTP, and PVST+ collectively.
Figure 133. STP Loop Guard Prevents Forwarding Loops Configuring Loop Guard Enable STP loop guard on a per-port or per-port channel basis. The following conditions apply to a port enabled with loop guard: ● Loop guard is supported on any STP-enabled port or port-channel interface.
● When used in a PVST+ network, STP loop guard is performed per-port or per-port channel at a VLAN level. If no BPDUs are received on a VLAN interface, the port or port-channel transitions to a Loop-Inconsistent (Blocking) state only for this VLAN. To enable a loop guard on an STP-enabled port or port-channel interface, use the following command. ● Enable loop guard on a port or port-channel interface.
57 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide. Figure 134.
Enable the SupportAssist service. CONFIGURATION mode support-assist activate DellEMC(conf)#support-assist activate This command guides you through steps to configure SupportAssist. Configuring SupportAssist Manually To manually configure SupportAssist service, use the following commands. 1. Accept the end-user license agreement (EULA). CONFIGURATION mode eula-consent {support-assist} {accept | reject} NOTE: Once accepted, you do not have to accept the EULA again.
support-assist DellEMC(conf)#support-assist DellEMC(conf-supportassist)# 3. (Optional) Configure the contact information for the company. SUPPORTASSIST mode contact-company name {company-name}[company-next-name] ... [company-next-name] DellEMC(conf)#support-assist DellEMC(conf-supportassist)#contact-company name test DellEMC(conf-supportassist-cmpy-test)# 4. (Optional) Configure the contact name for an individual.
[no] activity {full-transfer|core-transfer|event-transfer} DellEMC(conf-supportassist)#activity full-transfer DellEMC(conf-supportassist-act-full-transfer)# DellEMC(conf-supportassist)#activity core-transfer DellEMC(conf-supportassist-act-core-transfer)# DellEMC(conf-supportassist)#activity event-transfer DellEMC(conf-supportassist-act-event-transfer)# 2. Copy an action-manifest file for an activity to the system.
SUPPORTASSIST ACTIVITY mode [no] enable DellEMC(conf-supportassist-act-full-transfer)#enable DellEMC(conf-supportassist-act-full-transfer)# DellEMC(conf-supportassist-act-core-transfer)#enable DellEMC(conf-supportassist-act-core-transfer)# DellEMC(conf-supportassist-act-event-transfer)#enable DellEMC(conf-supportassist-act-event-transfer)# Configuring SupportAssist Company SupportAssist Company mode allows you to configure name, address and territory information of the company.
[no] contact-person [first ] last DellEMC(conf-supportassist)#contact-person first john last doe DellEMC(conf-supportassist-pers-john_doe)# 2. Configure the email addresses to reach the contact person. SUPPORTASSIST PERSON mode [no] email-address primary email-address [alternate email-address] DellEMC(conf-supportassist-pers-john_doe)#email-address primary jdoe@mycompany.com DellEMC(conf-supportassist-pers-john_doe)# 3. Configure phone numbers of the contact person.
[no] enable DellEMC(conf-supportassist-serv-default)#enable DellEMC(conf-supportassist-serv-default)# 4. Configure the URL to reach the SupportAssist remote server. SUPPORTASSIST SERVER mode [no] url uniform-resource-locator DellEMC(conf-supportassist-serv-default)#url https://192.168.1.1/index.htm DellEMC(conf-supportassist-serv-default)# Viewing SupportAssist Configuration To view the SupportAssist configurations, use the following commands: 1.
! server Dell enable url http://1.1.1.1:1337 DellEMC# 3. Display the EULA for the feature. EXEC Privilege mode show eula-consent {support-assist | other feature} DellEMC#show eula-consent support-assist SupportAssist EULA has been: Accepted Additional information about the SupportAssist EULA is as follows: By installing SupportAssist, you allow Dell to save your contact information (e.g.
58 System Time and Date System time and date settings and the network time protocol (NTP) are supported on Dell EMC Networking OS. You can set system times and dates and maintained through the NTP. They are also set through the Dell EMC Networking Operating System (OS) command line interfaces (CLIs) and hardware settings. The Dell EMC Networking OS supports reaching an NTP server through different VRFs. You can configure a maximum of eight logging servers across different VRFs or the same VRF.
Protocol Overview The NTP messages to one or more servers and processes the replies as received. The server interchanges addresses and ports, fills in or overwrites certain fields in the message, recalculates the checksum, and returns it immediately. Information included in the NTP message allows each client/server peer to determine the timekeeping characteristics of its other peers, including the expected accuracies of their clocks.
To display the system clock state with respect to NTP, use the show ntp status command from EXEC Privilege mode. DellEMC#show ntp status Clock is synchronized, stratum 4, reference is 10.16.151.117, vrf-id is 0 frequency is -44.862 ppm, stability is 0.050 ppm, precision is -18 reference time deeef7ef.85eeaa10 Tue, Jul 10 2018 9:16:31.523 UTC clock offset is -0.167449 msec, root delay is 149.194 msec root dispersion is 54.557 msec, peer dispersion is 0.
○ For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ○ For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ○ For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ○ For the Management interface, enter the keyword ManagementEthernet then the slot/port information. ○ For a port channel interface, enter the keywords port-channel then a number.
○ minpoll polling-interval: Enter the minpoll value. The range is from 4 to 16. ○ maxpoll polling-interval: Enter the maxpoll value. The range is from 4 to 16. 5. Configure the switch as NTP master. CONFIGURATION mode ntp master To configure the switch as NTP Server use the ntp master command. stratum number identifies the NTP Server's hierarchy. The following example shows configuring an NTP server. Dell EMC(conf)#show running-config ntp ! ntp master ntp server 10.16.127.
● Receive Timestamp — the arrival time on the client of the last NTP message from the server. If the server becomes unreachable, the value is set to zero. ● Transmit Timestamp — the departure time on the server of the current NTP message from the sender. ● Filter dispersion — the error in calculating the minimum delay from a set of sample data from a peer. To view the NTP configuration, use the show running-config ntp command in EXEC privilege mode.
Dell EMC Networking OS Time and Date You can set the time and date using the Dell EMC Networking OS CLI. Configuration Task List The following is a configuration task list for configuring the time and date settings.
configuration changed from "UTC 0 hrs 0 mins" to "Pacific -8 hrs 0 mins" DellEMC# Set Daylight Saving Time Dell EMC Networking OS supports setting the system to daylight saving time once or on a recurring basis every year. Setting Daylight Saving Time Once Set a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. To set the clock for daylight savings time once, use the following command. ● Set the clock to the appropriate timezone and daylight saving time.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ￭ first: Enter the keyword first to start daylight saving time in the first week of the month. ￭ last: Enter the keyword last to start daylight saving time in the last week of the month. start-month: Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. start-day: Enter the number of the day. The range is from 1 to 31.
59 Tunneling Tunnel interfaces create a logical tunnel for IPv4 or IPv6 traffic. Tunneling supports RFC 2003, RFC 2473, and 4213. DSCP, hop-limits, flow label values, open shortest path first (OSPF) v2, and OSPFv3 are supported. Internet control message protocol (ICMP) error relay, PATH MTU transmission, and fragmented packets are not supported.
The following sample configuration shows a tunnel configured in IPIP mode (IPv4 tunnel carries IPv4 and IPv6 traffic): DellEMC(conf)#interface tunnel 3 DellEMC(conf-if-tu-3)#tunnel source 5::5 DellEMC(conf-if-tu-3)#tunnel destination 8::9 DellEMC(conf-if-tu-3)#tunnel mode ipv6 DellEMC(conf-if-tu-3)#ip address 3.1.1.1/24 DellEMC(conf-if-tu-3)#ipv6 address 3::1/64 DellEMC(conf-if-tu-3)#no shutdown DellEMC(conf-if-tu-3)#show config ! interface Tunnel 3 ip address 3.1.1.
no shutdown DellEMC(conf)#interface tunnel 1 DellEMC(conf-if-tu-1)#ip unnumbered tengigabitethernet 1/1 DellEMC(conf-if-tu-1)#ipv6 unnumbered tengigabitethernet 1/1 DellEMC(conf-if-tu-1)#tunnel source 40.1.1.1 DellEMC(conf-if-tu-1)#tunnel mode ipip decapsulate-any DellEMC(conf-if-tu-1)#no shutdown DellEMC(conf-if-tu-1)#show config ! interface Tunnel 1 ip unnumbered TenGigabitEthernet 1/1 ipv6 unnumbered TenGigabitEthernet 1/1 tunnel source 40.1.1.
no shutdown 972 Tunneling
60 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if used with network interface controller (NIC) teaming, automatic recovery from a failed link.
Figure 136. Uplink Failure Detection How Uplink Failure Detection Works UFD creates an association between upstream and downstream interfaces. The association of uplink and downlink interfaces is called an uplink-state group. An interface in an uplink-state group can be a physical interface or a port-channel (LAG) aggregation of physical interfaces. An enabled uplink-state group tracks the state of all assigned upstream interfaces.
Figure 137. Uplink Failure Detection Example If only one of the upstream interfaces in an uplink-state group goes down, a specified number of downstream ports associated with the upstream interface are put into a Link-Down state. You can configure this number and is calculated by the ratio of the upstream port bandwidth to the downstream port bandwidth in the same uplink-state group.
● If one of the upstream interfaces in an uplink-state group goes down, either a user-configurable set of downstream ports or all the downstream ports in the group are put in an Operationally Down state with an UFD Disabled error. The order in which downstream ports are disabled is from the lowest numbered port to the highest.
The default is auto-recovery of UFD-disabled downstream ports is enabled. To disable auto-recovery, use the no downstream auto-recover command. 5. (Optional) Enter a text description of the uplink-state group. UPLINK-STATE-GROUP mode description text The maximum length is 80 alphanumeric characters. 6. (Optional) Disable upstream-link tracking without deleting the uplink-state group. UPLINK-STATE-GROUP mode no enable The default is upstream-link tracking is automatically enabled in an uplink-state group.
02:38:31: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Changed uplink state group state to up: Group 3 02:38:53: Fo 3/49 02:38:53: Fo 3/50 02:38:53: Fo 3/51 02:38:53: Fo 3/52 02:38:53: 02:38:53: 02:38:53: 02:38:53: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cleared from UFD error-disabled: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cleared from UFD error-disabled: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cleared from UFD error-disabled: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cle
Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/6(Up) Te 1/7(Up) Downstream Interfaces : Te 3/1(Up) Te 3/3(Up) Te 3/5(Up) Te 3/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 1/1(Dwn) Te 1/3(Dwn) Te 1/5(Dwn) Downstream Interfaces : Te 3/2(Dis) Te 3/4(Dis) Te 3/11(Dis) Te 3/12(Dis) Te 3/13(Dis) Te 3/14(Dis) Te 3/15(Dis) Uplink State Group : 6 Upstream Interfaces : Downstream Interfaces : Status: Enabled, Up Uplink State Group : 7 Upstream Interfaces : Downs
description test downstream disable links all downstream TenGigabitEthernet 1/21 upstream TenGigabitEthernet 1/22 upstream Port-channel 8 Sample Configuration: Uplink Failure Detection The following example shows a sample configuration of UFD on a switch/router in which you configure as follows. ● ● ● ● ● ● Configure uplink-state group 3. Add downstream links Tengigabitethernet 1/1, 1/2, 1/5, 1/9, 1/11, and 1/12. Configure two downstream links to be disabled if an upstream link fails.
61 Upgrade Procedures To find the upgrade procedures, go to the Dell EMC Networking OS Release Notes for your system type to see all the requirements needed to upgrade to the desired Dell EMC Networking OS version. To upgrade your system type, follow the procedures in the Dell EMC Networking OS Release Notes. You can download the release notes of your platform at https://www.force10networks.com. Use your login ID to log in to the website.
62 Virtual LANs (VLANs) Virtual LANs (VLANs) are a logical broadcast domain or logical grouping of interfaces in a local area network (LAN) in which all data received is kept locally and broadcast to all members of the group. When in Layer 2 mode, VLANs move traffic at wire speed and can span multiple devices. The system supports up to 4093 port-based VLANs and one default VLAN, as specified in IEEE 802.1Q.
NOTE: You cannot assign an IP address to the Default VLAN. To assign an IP address to a VLAN that is currently the Default VLAN, create another VLAN and assign it to be the Default VLAN. For more information about assigning IP addresses, refer to Assigning an IP Address to a VLAN. ● Untagged interfaces must be part of a VLAN. To remove an untagged interface from the Default VLAN, create another VLAN and place the interface into that VLAN.
● The VLAN protocol identifier identifies the frame as tagged according to the IEEE 802.1Q specifications (2 bytes). ● Tag control information (TCI) includes the VLAN ID (2 bytes total). The VLAN ID can have 4,096 values, but two are reserved. NOTE: The insertion of the tag header into the Ethernet frame increases the size of the frame to more than the 1,518 bytes as specified in the IEEE 802.3 standard. Some devices that are not compliant with IEEE 802.3 may not support the larger frame size.
Assigning Interfaces to a VLAN You can only assign interfaces in Layer 2 mode to a VLAN using the tagged and untagged commands. To place an interface in Layer 2 mode, use the switchport command. You can further designate these Layer 2 interfaces as tagged or untagged. For more information, see the Interfaces chapter and Configuring Layer 2 (Data Link) Mode.
When you remove a tagged interface from a VLAN (using the no tagged interface command), it remains tagged only if it is a tagged interface in another VLAN. If the tagged interface is removed from the only VLAN to which it belongs, the interface is placed in the Default VLAN as an untagged interface. Moving Untagged Interfaces To move untagged interfaces from the Default VLAN to another VLAN, use the following commands. 1. Access INTERFACE VLAN mode of the VLAN to which you want to assign the interface.
Assigning an IP Address to a VLAN VLANs are a Layer 2 feature. For two physical interfaces on different VLANs to communicate, you must assign an IP address to the VLANs to route traffic between the two interfaces. The shutdown command in INTERFACE mode does not affect Layer 2 traffic on the interface; the shutdown command only prevents Layer 3 traffic from traversing over the interface. NOTE: You cannot assign an IP address to the Default VLAN (VLAN 1).
Enabling Null VLAN as the Default VLAN In a Carrier Ethernet for Metro Service environment, service providers who perform frequent reconfigurations for customers with changing requirements occasionally enable multiple interfaces, each connected to a different customer, before the interfaces are fully configured. This presents a vulnerability because both interfaces are initially placed in the native VLAN, VLAN 1, and for that period customers are able to access each other's networks.
63 Virtual Link Trunking (VLT) Virtual link trunking (VLT) is a Dell EMC technology that provides two Dell EMC switches the ability to function as a single switch. VLT allows physical links between two Dell EMC switches to appear as a single virtual link to the network core or other switches such as Edge, Access, or top-of-rack (ToR). As a result, the two physical switches appear as a single switch to the connected devices.
VLT not only overcomes this caveat, but also provides a multipath to the connected devices. In the example shown below, the two physical VLT peers appear as a single logical device to the connected devices. As the connected devices consider the VLT peers as a single switch, VLT eliminates STP-blocked ports. However, the two VLT devices are independent Layer2/Layer3 (L2/L3) switches for devices in the upstream network. Figure 140.
Figure 141. Example of VLT Deployment VLT offers the following benefits: ● ● ● ● ● ● ● ● ● ● ● ● Allows a single device to use a LAG across two upstream devices. Eliminates STP-blocked ports. Provides a loop-free topology. Uses all available uplink bandwidth. Provides fast convergence if either the link or a device fails. Optimized forwarding with virtual router redundancy protocol (VRRP). Provides link-level resiliency. Assures high availability. Active-Active load sharing with VRRP.
● VLT backup link — The backup link monitors the connectivity between the VLT peer switches. The backup link sends configurable, periodic keep alive messages between the VLT peer switches. ● VLT interconnect (VLTi) — The link used to synchronize states between the VLT peer switches. Both ends must be on 10G or 40G interfaces. ● VLT domain — This domain includes both the VLT peer devices, VLT interconnect, and all of the port channels in the VLT connected to the attached devices.
Viewing the MAC Synchronization Between VLT Peers You can use the following commands to verify the MAC synchronization between VLT peers: VLT-10-PEER-1#show mac-address-table count MAC Entries for all vlans : Dynamic Address Count : 1007 Static Address (User-defined) Count : 1 Sticky Address Count : 0 Total Synced Mac from Peer(N): 503 Total MAC Addresses in Use: 1008 VLT-10-PEER-1#show vlt counter mac Total MAC VLT counters ---------------------L2 Total MAC-Address Count: 1007 VLT-10-PEER-1#show mac-addr
such that all the uplinks from servers to access and access to aggregation are in Active-Active Load Sharing mode. This example provides the highest form of resiliency, scaling, and load balancing in data center switching networks. The following example shows stacking at the access, VLT in aggregation, and Layer 3 at the core. Figure 143. VLT on Core Switches The aggregation layer is mostly in the L2/L3 switching/routing layer.
Figure 144. Enhanced VLT Configure Virtual Link Trunking VLT requires that you enable the feature and then configure the same VLT domain, backup link, and VLT interconnect on both peer switches. Important Points to Remember ● ● ● ● ● ● ● ● ● ● ● ● You cannot enable stacking simultaneously with VLT. If you enable both at the same time, unexpected behavior can occur. VLT port channel interfaces must be switch ports. If you include RSTP on the system, configure it before VLT.
● o disable this feature on VLT and port channels, use no lacp ungroup member-independent {vlt | portchannel} command under the configuration mode. ● When you enable IGMP snooping on the VLT peers, ensure the value of the delay-restore command is not less than the query interval.
○ A VLT domain consists of the two core chassis, the interconnect trunk, backup link, and the LAG members connected to attached devices. ○ Each VLT domain has a unique MAC address that you create or VLT creates automatically. ○ ARP tables are synchronized between the VLT peer nodes. ○ VLT peer switches operate as separate chassis with independent control and data planes for devices attached on non-VLT ports.
● ● ● ● ○ In the backup link between peer switches, heartbeat messages are exchanged between the two chassis for health checks. The default time interval between heartbeat messages over the backup link is 1 second. You can configure this interval. The range is from 1 to 5 seconds. DSCP marking on heartbeat messages is CS6.
○ In a VLT domain, the following software features are not supported on VLT ports: 802.1x, GVRP, and BFD. ● VLT and VRRP interoperability ○ In a VLT domain, VRRP interoperates with virtual link trunks that carry traffic to and from access devices (see Overview). The VLT peers belong to the same VRRP group and are assigned master and backup roles. Each peer actively forwards L3 traffic, reducing the traffic flow over the VLT interconnect.
The following recommendations help you avoid these issues and the associated traffic loss caused by using RSTP when you enable VLT on both VLT peers: ● Configure any ports at the edge of the spanning tree’s operating domain as edge ports, which are directly connected to end stations or server racks. Disable RSTP on ports connected directly to Layer 3-only routers not running STP or configure them as edge ports.
VLT Port Delayed Restoration When a VLT node boots up, if the VLT ports have been previously saved in the start-up configuration, they are not immediately enabled. To ensure MAC and ARP entries from the VLT per node are downloaded to the newly enabled VLT node, the system allows time for the VLT ports on the new node to be enabled and begin receiving traffic. The delay-restore feature waits for all saved configurations to be applied, then starts a configurable timer.
Figure 145. PIM-Sparse Mode Support on VLT On each VLAN where the VLT peer nodes act as the first hop or last hop routers, one of the VLT peer nodes is elected as the PIM designated router. If you configured IGMP snooping along with PIM on the VLT VLANs, you must configure VLTi as the static multicast router port on both VLT peer switches. This ensures that for first hop routers, the packets from the source are redirected to the designated router (DR) if they are incorrectly hashed.
If the VLT node elected as the designated router fails and you enable VLT Multicast Routing, multicast routes are synced to the other peer for traffic forwarding to ensure minimal traffic loss. If you did not enable VLT Multicast Routing, traffic loss occurs until the other VLT peer is selected as the DR. VLT Routing VLT Routing refers to the ability to run a dynamic routing protocol within a single VLT domain or between VLT domains (mVLT).
If you enable peer routing, a VLT node acts as a proxy gateway for its connected VLT peer as shown in the image below. Even though the gateway address of the packet is different, Peer-1 routes the packet to its destination on behalf of Peer-2 to avoid sub-optimal routing. Figure 147. Packets with peer routing enabled Benefits of Peer Routing ● ● Avoids sub-optimal routing ● Reduces latency by avoiding another hop in the traffic path.
Configuring VLT Unicast To enable and configure VLT unicast, follow these steps. 1. Enable VLT on a switch, then configure a VLT domain and enter VLT-domain configuration mode. CONFIGURATION mode vlt domain domain-id 2. Enable peer-routing. VLT DOMAIN mode peer-routing 3. Configure the peer-routing timeout. VLT DOMAIN mode peer-routing—timeout value value: Specify a value (in seconds) from 1 to 65535. The default value is infinity (without configuring the timeout).
3. Configure the multicast peer-routing timeout. VLT DOMAIN mode multicast peer-routing—timeout value value: Specify a value (in seconds) from 1 to 1200. NOTE: Reduce the multicast peer-routing-timeout value to 10 seconds to clear the (S,G) entry in mroute in primary VLT peer. Also, the MLD leave packet must be sent after the unicast route convergence. 4. Configure a PIM-SM compatible VLT node as a designated router (DR). For more information, refer to Configuring a Designated Router. 5.
Sample RSTP configuration The following is a sample of an RSTP configuration: Using the example shown in the Overview section as a sample VLT topology, the primary VLT switch sends BPDUs to an access device (switch or server) with its own RSTP bridge ID. BPDUs generated by an RSTP-enabled access device are only processed by the primary VLT switch. The secondary VLT switch tunnels the BPDUs that it receives to the primary VLT switch over the VLT interconnect.
Configuring a VLT Interconnect To configure a VLT interconnect, follow these steps. 1. Configure the port channel for the VLT interconnect on a VLT switch and enter interface configuration mode. CONFIGURATION mode interface port-channel id-number Enter the same port-channel number configured with the peer-link port-channel command as described in Enabling VLT and Creating a VLT Domain. NOTE: To be included in the VLTi, the port channel must be in Default mode (no switchport or VLAN assigned). 2.
4. Enable peer routing. VLT DOMAIN CONFIGURATION mode peer-routing If you enable peer routing, a VLT node acts as the proxy gateway for its peer. 5. (Optional) After you configure a VLT domain on each peer switch and connect (cable) the two VLT peers on each side of the VLT interconnect, the system elects a primary and secondary VLT peer device (see Primary and Secondary VLT Peers). To configure the primary and secondary roles before the election process, use the primary-priority command.
CONFIGURATION mode delay-restore delay-restore-time The range is from 1 to 1200. The default is 90 seconds. Reconfiguring the Default VLT Settings (Optional) To reconfigure the default VLT settings, use the following commands. 1. Enter VLT-domain configuration mode for a specified VLT domain. CONFIGURATION mode vlt domain domain-id The range of domain IDs is from 1 to 1000. 2.
4. Add one or more port interfaces to the port channel. INTERFACE PORT-CHANNEL mode channel-member interface interface: specify one of the following interface types: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 5. Ensure that the port channel is active. INTERFACE PORT-CHANNEL mode no shutdown 6.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 3. Enter VLT-domain configuration mode for a specified VLT domain. CONFIGURATION mode vlt domain domain-id The range of domain IDs is from 1 to 1000. 4. Enter the port-channel number that acts as the interconnect trunk. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 5.
13. Enable LACP on the LAN port. INTERFACE mode port-channel-protocol lacp 14. Configure the LACP port channel mode. INTERFACE mode port-channel number mode [active] 15. Ensure that the interface is active. MANAGEMENT INTERFACE mode no shutdown 16. Enable peer routing. VLT DOMAIN CONFIGURATION mode peer-routing If you enable peer routing, a VLT node acts as the proxy gateway for its peer. 17. Repeat steps 1 through 16 for the VLT peer node in Domain 1. 18.
EXEC Privilege mode show running-config entity 12. Verify that VLT is running. EXEC mode show vlt brief or show vlt detail 13. Verify that the VLT LAG is running in both VLT peer units. EXEC mode or EXEC Privilege mode show interfaces interface In the following sample VLT configuration steps, VLT peer 1 is Dell-2, VLT peer 2 is Dell-4, and the ToR is S60-1.
! no ip address port-channel-protocol LACP port-channel 2 mode active no shutdown configuring VLT peer lag in VLT Dell-2#show running-config interface port-channel 2 ! interface Port-channel 2 no ip address switchport vlt-peer-lag port-channel 2 no shutdown Dell-2#show interfaces port-channel 2 brief Codes: L - LACP Port-channel L LAG 2 Mode L2L3 Status up Uptime 03:33:14 Ports Te 1/4 (Up) In the ToR unit, configure LACP on the physical ports.
Delay-Restore timer : 90 seconds Delay-Restore Abort Threshold Peer-Routing Peer-Routing-Timeout timer Multicast peer-routing timeout DellEMC# : : : : 60 seconds Disabled 0 seconds 150 seconds Verify that the VLT LAG is up in VLT peer unit.
Interface Name ---------Po 1 Po 2 Te 1/10 Te 1/13 Interface Name ---------Po 1 Po 2 Te 1/10 Te 1/13 DellEMC# PortID -------128.2 128.3 128.230 128.233 Role -----Desg Desg Desg Desg Prio ---128 128 128 128 Cost -----188 2000 2000 2000 PortID -------128.2 128.3 128.230 128.233 Prio ---128 128 128 128 Designated Sts Cost Bridge ID PortID ----------- ------- -------------------- -------FWD(vltI) 0 0 90b1.1cf4.9b79 128.2 FWD(vlt) 0 0 90b1.1cf4.9b79 128.3 FWD 0 0 90b1.1cf4.9b79 128.230 FWD 0 0 90b1.1cf4.
Figure 148. Peer Routing Configuration Example Dell-1 Switch Configuration In the following output, RSTP is enabled with a bridge priority of 0. This ensures that Dell-1 becomes the root bridge. DellEMC#1#show run | find protocol protocol spanning-tree pvst no disable vlan 1,20,800,900 bridge-priority 0 The following output shows the existing VLANs.
(The management interfaces are part of a default VRF and are isolated from the switch’s data plane.) In Dell-1, te 0/0 and te 0/1 are used for VLTi. DellEMC#1#sh run int te0/0 interface TenGigabitEthernet 0/0 description VLTi LINK no ip address no shutdown (VLTi Physical link) ! DellEMC#1#sh run int te0/1 interface TenGigabitEthernet 0/1 description VLTi LINK no ip address no shutdown (VLTi Physical link) The following example shows that te 0/0 and te 0/1 are included in port channel 10.
Vlan 20 is used in Dell-1, Dell-2, and R1 to form OSPF adjacency. When OSPF is converged, the routing tables in all devices are synchronized. DellEMC#1#sh run int vlan 20 interface Vlan 20 description OSPF PEERING VLAN ip address 192.168.20.1/29 untagged Port-channel 1 no shutdown ! DellEMC#1#sh run int vlan 800 interface Vlan 800 description Client-VLAN ip address 192.168.8.1/24 tagged Port-channel 2 no shutdown The following output shows Dell-1 is configured with VLT domain 1.
Use the show vlt detail command to verify that VLT is functional and that the correct VLANs are allowed. DellEMC#1#sh vlt detail Local LAG Id -----------1 2 Peer LAG Id ----------1 2 Local Status -----------UP UP Peer Status ----------UP UP Active VLANs ------------20 1, 800, 900 The following output displays the OSPF configuration in Dell-1 DellEMC#1#sh run | find router router ospf 1 router-id 172.17.1.1 network 192.168.9.0/24 area 0 network 192.168.8.0/24 area 0 network 172.17.1.
0 0 90:b1:1c:f4:2c:bd 90:b1:1c:f4:29:f3 LOCAL_DA LOCAL_DA 00001 00001A The above output shows that the 90:b1:1c:f4:2c:bd MAC address belongs to Dell-1. The 90:b1:1c:f4:29:f3 MAC address belongs to Dell-2. Also note that these MAC addresses are marked with LOCAL_DA. This means, these are the local destination MAC addresses used by hosts when routing is required. Packets sent to this MAC address are directly forwarded to their destinations without being sent to the peer switch.
no ip address port-channel-protocol LACP port-channel 2 mode active no shutdown Te 0/6 connects to the uplink switch R1. Dell-2#sh run int te0/6 interface TenGigabitEthernet 0/6 description To_CR1_fa0/13 no ip address port-channel-protocol LACP port-channel 1 mode active no shutdown Port channel 1 connects the uplink switch R1.
Verify if VLT on Dell-1 is functional Dell-2#sh vlt brief VLT Domain Brief -----------------Domain ID: Role: Role Priority: 1 Secondary 55000 ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Peer routing : Peer routing-Timeout timer: Multicast peer routing timeout: Up Up Up 1 6(3) 90:b1:1c:f4:29:f1 90:b1:1c:f4:2c:bb 90:b1:1c:f4:01:01 6(3) 90 seconds En
The following output displays the routes learned using OSPF. Dell-2 also learns the routes to the loopback addresses on R1 through OSPF. Dell-2#show ip route ospf Destination Gateway ----------------O 2.2.2.2/24 via 192.168.20.3, O 3.3.3.2/24 via 192.168.20.3, O 4.4.4.2/24 via 192.168.20.3, O 172.15.1.1/32 via 192.168.20.3, O 172.16.1.2/32 via 192.168.20.
network 172.15.1.0 0.0.0.255 area 0 network 192.168.20.0 0.0.0.7 area 0 CR1#show ip ospf neighbor (R1 is a DROTHER) Neighbor ID Pri State Dead Time Address Interface 172.16.1.2 1 FULL/BDR 00:00:31 192.168.20.2 Port-channel1 172.17.1.1 1 FULL/DR 00:00:38 192.168.20.1 Port-channel1 CR1#show ip route (Output Truncated) 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Loopback2 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, Loopback3 O 192.168.8.0/24 [110/2] via 192.168.
Figure 149. eVLT Configuration Example eVLT Configuration Step Examples In Domain 1, configure the VLT domain and VLTi on Peer 1. Domain_1_Peer1#configure Domain_1_Peer1(conf)#interface port-channel 1 Domain_1_Peer1(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-1/9 Domain_1_Peer1(conf)#vlt domain 1000 Domain_1_Peer1(conf-vlt-domain)# peer-link port-channel 1 Domain_1_Peer1(conf-vlt-domain)# back-up destination 10.16.130.
Configure eVLT on Peer 2. Domain_1_Peer2(conf)#interface port-channel 100 Domain_1_Peer2(conf-if-po-100)# switchport Domain_1_Peer2(conf-if-po-100)# vlt-peer-lag port-channel 100 Domain_1_Peer2(conf-if-po-100)# no shutdown Add links to the eVLT port-channel on Peer 2.
PIM-Sparse Mode Configuration Example The following sample configuration shows how to configure the PIM Sparse mode designated router functionality on the VLT domain with two VLT port-channels that are members of VLAN 4001. For more information, refer to PIM-Sparse Mode Support on VLT. Examples of Configuring PIM-Sparse Mode The following example shows how to enable PIM multicast routing on the VLT node globally.
show vlt role ● Display the current configuration of all VLT domains or a specified group on the switch. EXEC mode show running-config vlt ● Display statistics on VLT operation. EXEC mode show vlt statistics ● Display the RSTP configuration on a VLT peer switch, including the status of port channels used in the VLT interconnect trunk and to connect to access devices. EXEC mode show spanning-tree rstp ● Display the current status of a port or port-channel interface used in the VLT domain.
Peer-Routing-Timeout timer Multicast peer-routing timeout DellEMC# : 0 seconds : 150 seconds The following example shows the show vlt detail command.
HeartBeat Messages Sent: HeartBeat Messages Received: ICL Hello's Sent: ICL Hello's Received: 994 978 89 89 The following example shows the show spanning-tree rstp command. The bold section displays the RSTP state of port channels in the VLT domain. Port channel 100 is used in the VLT interconnect trunk (VLTi) to connect to VLT peer2. Port channels 110, 111, and 120 are used to connect to access switches or servers (vlt).
Dell_VLTpeer1(conf-if-ma-1/1)#no shutdown Dell_VLTpeer1(conf-if-ma-1/1)#exit Configure the VLT interconnect (VLTi). Dell_VLTpeer1(conf)#interface port-channel 100 Dell_VLTpeer1(conf-if-po-100)#no ip address Dell_VLTpeer1(conf-if-po-100)#channel-member fortyGigE 1/49,50 Dell_VLTpeer1(conf-if-po-100)#no shutdown Dell_VLTpeer1(conf-if-po-100)#exit Configure the port channel to an attached device.
Verify that the port channels used in the VLT domain are assigned to the same VLAN.
Table 134. Troubleshooting VLT (continued) Description Behavior at Peer Up Behavior During Run Time Action to Take Spanning tree mismatch at port level A syslog error message is generated. A one-time informational syslog message is generated. Correct the spanning tree configuration on the ports. System MAC mismatch A syslog error message and an A syslog error message and an Verify that the unit ID of VLT SNMP trap are generated. SNMP trap are generated.
Layer 2 redundancy mechanism, support for configuration of VLT nodes in a PVLAN enables Layer 2 security functionalities. To achieve maximum VLT resiliency, you should configure the PVLAN IDs and mappings to be identical on both the VLT peer nodes. The association of PVLAN with the VLT LAG must also be identical. After the VLT LAG is configured to be a member of either the primary or secondary PVLAN (which is associated with the primary), ICL becomes an automatic member of that PVLAN on both switches.
Whenever a change occurs in the VLAN mode of one of the peers, this modification is synchronized with the other peers. Depending on the validation mechanism that is initiated for MAC synchronization of VLT peers, MAC addresses learned on a particular VLAN are either synchronized with the other peers, or MAC addresses synchronized from the other peers on the same VLAN are deleted. This method of processing occurs when the PVLAN mode of VLT LAGs is modified.
Table 135.
Table 135. VLAN Membership and MAC Synchronization With VLT Nodes in PVLAN (continued) VLT LAG Mode PVLAN Mode of VLT VLAN Peer1 Peer2 Peer1 Peer2 Trunk Access Primary/Normal Secondary ICL VLAN Membership Mac Synchronization No No Configuring a VLT VLAN or LAG in a PVLAN You can configure the VLT peers or nodes in a private VLAN (PVLAN).
Associating the VLT LAG or VLT VLAN in a PVLAN 1. Access INTERFACE mode for the port that you want to assign to a PVLAN. CONFIGURATION mode interface interface 2. Enable the port. INTERFACE mode no shutdown 3. Set the port in Layer 2 mode. INTERFACE mode switchport 4. Select the PVLAN mode. INTERFACE mode switchport mode private-vlan {host | promiscuous | trunk} ● host (isolated or community VLAN port) ● promiscuous (intra-VLAN communication port) ● trunk (inter-switch PVLAN hub port) 5.
Proxy ARP is not performed when the ICL link is up and the ARP request the wrong VLT peer. In this case, ARP requests are tunneled to the VLT peer. Proxy ARP supported on both VLT interfaces and non-VLT interfaces. Proxy ARP is supported on symmetric VLANs only. Proxy ARP is enabled by default. To support proxy ARP, the routing table must be symmetrically configured. For example, consider a sample topology in which you configure VLAN 100 on two VLT nodes, node 1 and node 2.
to the device. For the (S, G) routes that are synchronized from the VLT peer, after the RP starts receiving multicast traffic via these routes, these (S, G) routes are considered valid and are downloaded to the device. Only (S, G) routes are used to forward the multicast traffic from the source to the receiver. You can configure VLT nodes, which function as RP, as Multicast source discovery protocol (MSDP) peers in different domains.
Configure the VLT LAG as VLAN-Stack Access or Trunk Port DellEMC(conf)#interface port-channel 10 DellEMC(conf-if-po-10)#switchport DellEMC(conf-if-po-10)#vlt-peer-lag port-channel 10 DellEMC(conf-if-po-10)#vlan-stack access DellEMC(conf-if-po-10)#no shutdown DellEMC#show running-config interface port-channel 10 ! interface Port-channel 10 no ip address switchport vlan-stack access vlt-peer-lag port-channel 10 no shutdown DellEMC# DellEMC(conf)#interface port-channel 20 DellEMC(conf-if-po-20)#switchport Dell
Configure the VLT domain DellEMC(conf)#vlt domain 1 DellEMC(conf-vlt-domain)#peer-link port-channel 1 DellEMC(conf-vlt-domain)#back-up destination 10.16.151.115 DellEMC(conf-vlt-domain)#system-mac mac-address 00:00:00:11:11:11 DellEMC(conf-vlt-domain)#unit-id 1 DellEMC(conf-vlt-domain)# DellEMC#show running-config vlt vlt domain 1 peer-link port-channel 1 back-up destination 10.16.151.
Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged NUM 50 Status Active Description DellEMC# Q M M V Ports Po10(Te 1/8) Po20(Te 1/20) Po1(Te 1/30-32) IPv6 Peer Routing in VLT Domains Overview VLT enables the phys
● When you enable and configure VLT on both VLT node1 and node2, any dynamically learned ND entry in VLT node1 be synchronizes instantaneously to VLT node2 and vice-versa. The link-local address also synchronizes if learned on the VLT VLAN interface. ● During failure cases, when a VLT node goes down and comes back up all the ND entries learned via VLT interface must synchronize to the peer VLT node.
Figure 150. Sample Configuration of IPv6 Peer Routing in a VLT Domain Sample Configuration of IPv6 Peer Routing in a VLT Domain Consider a sample scenario as shown in the following figure in which two VLT nodes, Unit1 and Unit2, are connected in a VLT domain using an ICL or VLTi link. To the south of the VLT domain, Unit1 and Unit2 are connected to a ToR switch named Node B. Also, Unit1 is connected to another node, Node A, and Unit2 is linked to a node, Node C.
Consider a case in which NS for VLT node1 IP reaches VLT node1 on the VLT interface and NS for VLT node1 IP reaches VLT node2 due to LAG level hashing in the ToR. When VLT node1 receives NS from VLT VLAN interface, it unicasts the NA packet on the VLT interface. When NS reaches VLT node2, it is flooded on all interfaces including ICL. When VLT node 1 receives NS on ICL, it floods the NA packet on the VLAN. If NS is unicast and if it reaches the wrong VLT peer, it is lifted to the CPU using ACL entry.
When VLT node receives traffic from non-VLT host intended to VLT host, it routes the traffic to VLT interface. If VLT interface is not operationally up VLT node will route the traffic over ICL. Non-VLT host to North Bound traffic flow When VLT node receives traffic from non-VLT host intended to north bound with DMAC as self MAC it routes traffic to next hop.
ToR 1. Enable BFD globally. TOR(conf)# bfd enable 2. Configure a VLT peer LAG. TOR(conf)#interface tengigabitethernet 1/1 TOR(conf-if-te-1/1)#no ip address TOR(conf-if-te-1/1)#port-channel-protocol lacp TOR(conf-if-te-1/1)#port-channel 10 mode active TOR(conf-if-te-1/1)#no shutdown TOR(conf)#interface tengigabitethernet 1/2 TOR(conf-if-te-1/2)#no ip address TOR(conf-if-te-1/2)#port-channel-protocol lacp TOR(conf-if-te-1/2)#port-channel 10 mode active TOR(conf-if-te-1/2)#no shutdown 3.
5. Enable BFD over OSPF. TOR(conf)# router ospf 1 TOR(conf-router_ospf)# network 100.1.1.0/24 area 0 TOR(conf-router_ospf)# bfd all-neighbors VLT Primary 1. Enable BFD globally. VLT_Primary(conf)# bfd enable 2. Configure port channel which is used as VLTi link. VLT_Primary(conf)# interface VLT_Primary(conf-if-po-100)# VLT_Primary(conf-if-po-100)# VLT_Primary(conf-if-po-100)# port-channel 100 no ip address channel-member tengigabitethernet 1/1, 1/2 no shutdown 3. Enable VLT and configure a VLT domain.
2. Configure port channel which is used as VLTi link. VLT_Secondary(conf)# interface VLT_Secondary(conf-if-po-100)# VLT_Secondary(conf-if-po-100)# VLT_Secondary(conf-if-po-100)# port-channel 100 no ip address channel-member tengigabitethernet 1/1, 1/2 no shutdown 3. Enable VLT and configure a VLT domain. VLT_Secondary(conf)# vlt domain VLT_Secondary(conf-vlt-domain)# VLT_Secondary(conf-vlt-domain)# VLT_Secondary(conf-vlt-domain)# 100 peer-link port-channel 100 back-up destination 10.16.206.
Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: 60 seconds Enabled 0 seconds 150 seconds ● To verify the VLTi (ICL) link is up in the VLT secondary peer, use show vlt brief command.
Static VXLAN Configuration in a VLT setup Configuration steps are covered below: 1. Both Gateway VTEPs need VLT configured. ● ICL port configuration interface Port-channel 1 no ip address channel-member TenGigabitEthernet 0/4-5 no shutdown ● VLT Domain Configuration vlt domain 100 peer-link port-channel 1 back-up destination 10.11.70.14 ● VXLAN Instance Configuration vxlan-instance 1 static local-vtep-ip 14.14.14.
vni-profile test vnid 200 remote-vtep-ip 3.3.3.3 vni-profile test ● VLT Access port configuration interface TengigabitEthernet 0/12 port-channel-protocol lacp port-channel 30 mode active interface Port-channel 30 no ip address vxlan-instance 1 switchport vlt-peer-lag port-channel 30 no shutdown 2. Configure loopback interface and VXLAN instances on both the peers. ● Configure loopback interface IP address on both peers with the same IPaddress. interface Loopback 1 ip address 14.14.14.14/32 no shutdown 3.
64 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
Figure 152. Sample Configuration for a VLT Proxy Gateway Guidelines for Enabling the VLT Proxy Gateway Keep the following points in mind when you enable a VLT proxy gateway: ● Proxy gateway is supported only for VLT; for example, across a VLT domain. ● You must enable the VLT peer-routing command for the VLT proxy gateway to function.
● Private VLANs (PVLANs) are not supported. ● When a Virtual Machine (VM) moves from one VLT domain to the another VLT domain, the VM host sends the gratuitous ARP (GARP) , which in-turn triggers a mac movement from the previous VLT domain to the newer VLT domain. ● After a station move, if the host sends a TTL1 packet destined to its gateway; for example, a previous VLT node, the packet can be dropped.
● You cannot have interface–level LLDP disable commands on the interfaces configured for proxy gateway and you must enable both transmission and reception. ● You must connect both units of the remote VLT domain by the port channel member. ● If you connect more than one port to a unit of the remote VLT domain, the connection must be completed by the time you enable the proxy gateway LLDP. ● You cannot have other conflicting configurations (for example, you cannot have a static proxy gateway configuration).
For VLT Proxy Gateway to work in this scenario you must configure the VLT-peer-mac transmit command under VLT Domain Proxy Gateway LLDP mode, in both C and D (VLT domain 1) and C1 and D1 (VLT domain 2). This behavior is applicable only in the LLDP configuration and not required in the static configuration.
Sample Dynamic Proxy Configuration on C switch or C1 switch Switch_C#conf Switch_C(conf)#vlt domain 1 Switch_C(conf-vlt-domain1)#proxy-gateway lldp Switch_C(conf-vlt-domain1-pxy-gw-lldp)#peer-domain-link port-channel 1.... VLT Proxy Gateway Sample Topology VLT proxy gateway enables one VLT domain to act as proxy gateway for another VLT domain when a host or virtual machine is moved from one VLT domain to the other VLT domain.
interface TenGigabitEthernet 0/9 description "To DELL-3 10Gb" no ip address ! port-channel-protocol LACP port-channel 50 mode active no shutdown interface Port-channel 50 description "mVLT port channel to DELL-3" no ip address switchport no spanning-tree vlt-peer-lag port-channel 50 no shutdown Note that on the inter-domain link, the switchport command is enabled. On a VLTi link between VLT peers in a VLT domain, the switchport command is not used.
The MAC addresses, configured using the remote-mac-address command, belong to Dell-3 and Dell-4. interface Vlan 100 description OSPF peering VLAN to Dell-1 ip address 10.10.100.2/30 ip ospf network point-to-point no shutdown The following is the OSPF configuration on Dell-2. router ospf 1 router-id 2.2.2.2 network 10.10.100.0/30 area 0 The following output shows that Dell-1 forms OSPF neighborship with Dell-2. Dell-2#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface Area 4.4.4.
ip ospf network point-to-point no shutdown The following is the OSPF configuration on Dell-3. router ospf 1 router-id 3.3.3.3 network 10.10.101.0/30 area 0 network 10.10.102.0/30 area 0 The following output shows that Dell-4 and VLT domain 120 form OSPF neighborship with Dell-3. Dell-3#sh ip ospf nei ! Neighbor ID Pri State Dead Time Address Interface Area 4.4.4.4 1 FULL/ - 00:00:33 10.10.101.1 Vl 101 0 1.1.1.1 1 FULL/ - 00:00:34 10.10.102.
65 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS. Overview The switch acts as the VXLAN gateway and performs the VXLAN Tunnel End Point (VTEP) functionality. VXLAN is a technology where in the data traffic from the virtualized servers is transparently transported over an existing legacy network. Figure 155. VXLAN Gateway NOTE: In a stack setup, the Dell EMC Networking OS does not support VXLAN.
• • Routing in and out of VXLAN tunnels NSX Controller-based VXLAN for VLT Components of VXLAN network VXLAN provides a mechanism to extend an L2 network over an L3 network. In short, VXLAN is an L2 overlay scheme over an L3 network and this overlay is termed as a VXLAN segment.
Legacy TOR It is a TOR switch, which performs routing or switching decisions. Functional Overview of VXLAN Gateway The following section is the functional overview of VXLAN Gateway: 1. Provides connectivity between a Virtual server infrastructure and a Physical server infrastructure. 2. Provides the functions performed by a VTEP in a virtual server infrastructure. The functions of a VTEP are: ● VTEP is responsible for creating one or more logical networks.
● VLAN: It is optional in a VXLAN implementation and will be designated by an ethertype of 0×8100 and has an associated VLAN ID tag. ● Ethertype: It is set to 0×0800 because the payload packet is an IPv4 packet. The initial VXLAN draft does not include an IPv6 implementation, but it is planned for the next draft. Outer IP Header: The Outer IP Header consists of the following components: ● Protocol: It is set to 0×11 to indicate that the frame contains a UDP packet .
Configuring and Controlling VXLAN from the NSX Controller GUI You can configure and control VXLAN from the NSX controller GUI, by adding a hardware device to NSX and authenticating the device. 1. Generate a certificate in your system and add it to the NSX before adding a hardware device for authentication. To generate a certificate, use the following command: ● crypto cert generate self-signed cert-file flash://vtep-cert.pem key-file flash:// vtep-privkey.
Figure 157. Create VXLAN Gateway To create a VXLAN L2 Gateway, the IP address of the Gateway is required. After connectivity is established between the VTEP and NSX controller, the management IP address and the connectivity status are populated as shown in the following image. Figure 158. Hardware Devices 3. Add a service node or replicator. Under Home > Networking and Security > Service Definition > Hardware Devices > Replication Cluster, click the Edit button.
Figure 159. Add Service Node or Replicator NOTE: Ensure L3 reachability between the VTEP and the replicator. 4. Create Logical Switch. You can create a logical network by creating a logical switch. The logical network acts as the forwarding domain for workloads on the physical as well as virtual infrastructure. Click Home > Networking and Security > Logical Switches and click Add. The New Logical Switch window opens. Enter a name and select Unicast as the replication mode and click OK. Figure 160.
In the Manage Hardware Bindings window, expand a VTEP and click Add. The Manage Hardware Bindings Window opens. Click the Select link and the Specify Hardware Port window opens. Click the hardware port and click OK. Figure 161. Specify Hardware Port In the Manage Hardware Bindings window, under the VLAN column, enter the VLAN ID and press OK. Figure 162. Create Logical Switch Port 6. (Optional) Enable or disable BFD globally. Go to Hardware Devices tab > BFD Configuration, and click the Edit button.
Figure 163. Edit VXLAN BFD Configuration NOTE: For more details about NSX controller configuration, refer to the NSX user guide from VMWare . Configuring and Controling VXLAN from Nuage Controller GUI The Dell EMC Networking OS supports Nuage controller for VXLAN. You can configure and control VXLAN from the Nuage controller GUI, by adding a hardware device to the Nuage controller and authenticating the device. 1. Under the Infrastructure tab, add a datacenter gateway. Figure 164.
Figure 165. Port-to-VLAN mappings 3. Under the Networks tab, create an L2 domain. Under the L2 domain, create a logical network (VNI) and add access ports of the VTEP in the logical network. Figure 166. Access ports of the VTEP Configuring VxLAN Gateway To configure the VxLAN gateway on the switch, follow these steps: 1. Connecting to NVP controller 2. Advertising VXLAN access ports to controller Connecting to an NVP Controller To connect to an NVP controller, use the following commands. 1.
3. Define how the device connects to the controller. VxLAN INSTANCE mode controller controller ID ip address port port-number TCP | SSL The port number range is from 1 to 6632. The default connection type is SSL. TCP, PTCP, and PSSL are supported with NSX controller only. 4. Enter the gateway IP VxLAN INSTANCE mode gateway-ip IP address 5. Enter the maximum backoff time (Optional). VxLAN INSTANCE mode max_backoff time The range is from 1000-180000. The default value is 30000 milliseconds. 6.
The following example shows the show vxlan vxlan-instance logical-network command. • show vxlan vxlan-instance 1 logical-network Instance : 1 Total LN count : 1024 * - No VLAN mapping exists and yet to be installed Name VNID 1ba08465-8774-3383-ba51-8b7e642ff632 6427 02f063c2-36c7-3ef6-a324-b432b748d15d 6218 36ab6265-5fa8-3ce8-b35c-e7cfdaf7c9e8 6368 The following example shows the show vxlan vxlan-instance statistics interface command.
Examples of the show bfd neighbors command. To verify that the session is established, use the show bfd neighbors command. Dell_GW1#show bfd neighbors * Ad Dn B C I O O3 R M V VT * * * * * * - Active session role Admin Down BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr 1.0.1.1 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 RemoteAddr 1.0.1.2 192.168.122.135 192.168.122.136 192.168.122.137 192.168.122.138 192.168.122.
VNI-PROFILE mode vnid VNID Range 6. Create a remote tunnel and associate the remote VTEP to the VNID. VXLAN-INSTANCE mode remote—vtep—ip remote IP Address vni-profile profile name 7. Enable the VXLAN. VXLAN-INSTANCE mode no shutdown 8. Enable VXLAN instance on the interface. The interface should not be on layer 2. INTERFACE mode vxlan-instance Instance ID 9. Associate VNID to VLAN.
Use the following command to clear the remote VTEP and access port statistics. DellEMC# clear vxlan vxlan-instance 1 statistics Disabling MAC Address Learning on Static VXLAN Tunnels You can configure the system to not learn MAC addresses on static VXLAN tunnels or remote VTEPs. MAC address learning on static VXLAN tunnels is Enabled by default.
Following is the output of show ip routecommand for the above connection: DellEMC# show ip route Destination Gateway --------------- Dist/Metric Last ----------- *B IN 0.0.0.0/0 C 1.1.1.1/32 B IN 2.2.2.2/32 200/0 0/0 200/0 via 192.168.11.2 Direct, Lo 1 via 192.168.22.1 Change ----------16:13:30 8:59:34 00:36:48 From the above routing table it is understood that the remote VTEP 2.2.2.2/32 is resolved through next-hop 192.168.22.1, which is not directly connected.
In this RIOT scheme, whenever R1 tries to reach R2, the packet gets to P1 on VTEP 1 with VLAN 10 and gets routed out of P2 on VLAN 20. VTEP 1 sends an ARP request for R2 (10.1.2.1) through P2. This request gets VXLAN encapsulated at P3 and is sent out of P4. Eventually, the native ARP request reaches R2. R2 sends an ARP response that is VXLAN encapsulated at VTEP 2. This response reaches VTEP 1 on P4 with a VXLAN encapsulation. At this point, the ARP response is de-capsulated at P4.
The topology to achieve RIOT with a physical loopback is inherently susceptible to Layer 2 loops. To prevent these loops from disrupting the network, the following egress masks need to be applied: ● ● ● ● Any Any Any Any frame frame frame frame ingressing ingressing ingressing ingressing on on on on a a a a VXLAN access port is not allowed to egress out of a VXLAN loopback port. VXLAN loopback port is not allowed to egress out of a VXLAN access port.
In this topology, P2 and P3 in VTEP 1 are VLT port-channels with corresponding VLT peer LAGs being P2 and P3 in VTEP 2. Similarly, P6 and P7 in VTEP 3 are VLT port-channels with corresponding VLT peer LAGs being P6 and P7 in VTEP 4. NOTE: P2, P3, P6, and P7 can be a single port or multi-port port-channels that are VLT port-channels. NOTE: The VLT VXLAN configuration for RIOT deviates from the standard VLT behavior when these physical loopbacks are provisioned as VLT port-channels.
Figure 168. Controller-based VXLAN for VLT Providing Redundancy Important Points to Remember ● The VLT peer port channel number must be the same on both VLT peers. ● before configuring controller-based VXLAN with VLT, remove any existing standalone VXLAN configuration. ● BFD tunnels come up only after the NSX controller sends tunnel details. The details come after the remote MAC addresses are downloaded from NSX controller.
bfd enable Enter the result of your step here (optional). 2. Create an uplink-state group. CONFIGURATION mode uplink-state-group group-id group-id: values are from 1 to 16. 3. Assign a VLT port channel to the uplink-state group as an upstream link. UPLINK-STATE-GROUP mode upstream interface 4. Assign a network port or port channel to the uplink-state group as a downstream link.
vlt domain domain-id The domain ID range is from 1 to 1000. Configure the same domain ID on the peer switch 2. Configure the IP address of the management interface on the remote VLT peer to be used as the endpoint of the VLT backup link for sending out-of-band hello messages. VLT DOMAIN CONFIGURATION mode back-up destination ip-address 3. Configure the port channel to be used as the VLT interconnect between VLT peers in the domain. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 4.
vlt-peer-lag port-channel 10 no shutdown The following are some of the show command outputs on the VLT primary: DellEMC#show vlt brief VLT Domain Brief -----------------Domain ID: Role: Role Priority: ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: D
Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow, Vx - Vxlan Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged * NUM 1 Status Active Vx 20 Active 500 Active Description DellEMC# DellEMC# DellEMC#sh vxlan vxlan-instance 1 multicast-mac * - Active Replicator
Role Priority: ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: DellEMC# DellEMC# DellEMC# 10 Up Up Up 1 6(8) f4:8e:38:2b:3e:85 14:18:77:0a:53:80 00:00:00:11:11:11 6(8) 90 seconds 60 seconds Enabled 0 seconds 150 seconds DellEMC#sh vxlan vxlan-insta
Tunnel : count 1 6.6.6.2 : vxlan_over_ipv4 (up) DellEMC#show vxlan vxlan-instance 1 unicast-mac-local Total Local Mac Count: 1 VNI MAC PORT 5000 00:00:00:cc:00:00 (N) Po 1 DellEMC#show vxlan vxlan-instance 1 unicast-mac-remote Total Remote Mac Count: 1 VNI MAC TUNNEL 5000 00:00:bb:00:00:00 4.3.3.
66 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows a physical router to partition itself into multiple Virtual Routers (VRs). The control and data plane are isolated in each VR so that traffic does NOT flow across VRs.Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist within the same router at the same time.
Figure 169. VRF Network Example VRF Configuration Notes Although there is no restriction on the number of VLANs that can be assigned to a VRF instance, the total number of routes supported in VRF is limited by the size of the IPv4 CAM. VRF is implemented in a network device by using Forwarding Information Bases (FIBs). A network device may have the ability to configure different virtual routers, where entries in the FIB that belong to one VRF cannot be accessed by another VRF on the same device.
NOTE: To configure a router ID in a non-default VRF, configure at least one IP address in both the default as well as the non-default VRF. Table 136. Software Features Supported on VRF Feature/Capability Support Status for Default VRF Support Status for Non-default VRF 802.
DHCP DHCP requests are not forwarded across VRF instances. The DHCP client and server must be on the same VRF instance. VRF Configuration The VRF configuration tasks are: 1. Enabling VRF in Configuration Mode 2. Creating a Non-Default VRF 3. Assign an Interface to a VRF You can also: ● View VRF Instance Information ● Connect an OSPF Process to a VRF Instance ● Configure VRRP on a VRF Loading VRF CAM ● Load CAM memory for the VRF feature.
2. Assign the interface to management VRF. INTERFACE CONFIGURATION ip vrf forwarding management Before assigning a front-end port to a management VRF, ensure that no IP address is configured on the interface. 3. Assign an IPv4 address to the interface. INTERFACE CONFIGURATION ip address 10.1.1.1/24 Before assigning a front-end port to a management VRF, ensure that no IP address is configured on the interface. 4. Assign an IPv6 address to the interface.
Table 137. Configuring VRRP on a VRF (continued) Task Command Syntax Assign an IP address to the interface Configure the VRRP group and virtual IP address View VRRP command output for the VRF vrf1 Command Mode ip address 10.1.1.1 /24 no shutdown vrrp-group 10 virtual-address 10.1.1.100 show config ----------------------------! interface TenGigabitEthernet 1/13 ip vrf forwarding vrf1 ip address 10.1.1.1/24 ! vrrp-group 10 virtual-address 10.1.1.
● ● ● ● ● ● ipv6 ipv6 ipv6 ipv6 ipv6 ipv6 nd reachable-time — Set advertised reachability time nd retrans-timer — Set NS retransmit interval used and advertised in RA nd suppress-ra — Suppress IPv6 Router Advertisements ad — IPv6 Address Detection ad autoconfig — IPv6 stateless auto-configuration address — Configure IPv6 address on an interface NOTE: The command line help still displays relevant details corresponding to each of these commands.
Figure 171. Setup VRF Interfaces The following example relates to the configuration shown in the above illustrations. Router 1 ip vrf blue 1 ! ip vrf orange 2 ! ip vrf green 3 ! interface TenGigabitEthernet no ip address switchport no shutdown ! interface TenGigabitEthernet ip vrf forwarding blue ip address 10.0.0.1/24 no shutdown ! interface TenGigabitEthernet ip vrf forwarding orange ip address 20.0.0.1/24 no shutdown ! interface TenGigabitEthernet ip vrf forwarding green ip address 30.0.0.
ip vrf forwarding blue ip address 1.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 192 ip vrf forwarding orange ip address 2.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.1 network 1.0.0.0/24 area 0 network 10.0.0.0/24 area 0 ! router ospf 2 vrf orange router-id 2.0.0.1 network 2.0.0.0/24 area 0 network 20.0.0.
! router ospf 1 vrf blue router-id 1.0.0.2 network 11.0.0.0/24 area 0 network 1.0.0.0/24 area 0 passive-interface TenGigabitEthernet 2/1 ! router ospf 2 vrf orange router-id 2.0.0.2 network 21.0.0.0/24 area 0 network 2.0.0.0/24 area 0 passive-interface TenGigabitEthernet 2/2 ! ip route vrf green30.0.0.0/24 3.0.0.1 ! The following shows the output of the show commands on Router 1.
Change Destination --------------------C 2.0.0.0/24 C 20.0.0.0/24 O 21.0.0.0/24 00:10:41 Gateway Dist/Metric ------- ----------- Direct, Vl 192 Direct, Te 1/2 via 2.0.0.
C 11.0.0.
Dynamic Route Leaking Route Leaking is a powerful feature that enables communication between isolated (virtual) routing domains by segregating and sharing a set of services such as VOIP, Video, and so on that are available on one routing domain with other virtual domains. Inter-VRF Route Leaking enables a VRF to leak or export routes that are present in its RTM to one or more VRFs.
ip route-import 1:1 5. Configure the export target in VRF-red. ip route-export 2:2 6. Configure VRF-blue. ip vrf vrf-blue interface-type slot/port[/subport] ip vrf forwarding VRF-blue ip address ip—address mask A non-default VRF named VRF-blue is created and the interface 1/12 is assigned to it. 7. Configure the import target in VRF-blue. ip route-import 1:1 8. Configure the export target in VRF-blue. ip route-import 3:3 9. Configure VRF-green.
DellEMC# show ip route vrf VRF-Shared O 44.4.4.4/32 via 144.4.4.4 110/0 C 144.4.4.0/24 00:00:11 Direct, Te 1/4 0/0 00:32:36 Show routing tables of VRFs( after route-export and route-import tags are configured). DellEMC# show ip route vrf VRF-Red O C O C 11.1.1.1/32 111.1.1.0/24 44.4.4.4/32 144.4.4.0/24 via 111.1.1.1 110/0 00:00:10 Direct, Te 1/11 0/0 22:39:59 via VRF-shared:144.4.4.4 0/0 00:32:36 Direct, VRF-shared:Te 1/4 0/0 00:32:36 DellEMC# show ip route vrf VRF-Blue O 22.2.2.2/32 via 122.2.2.
You can use the match source-protocol or match ip-address commands to specify matching criteria for importing or exporting routes between VRFs. NOTE: You must use the match source-protocol or match ip-address commands in conjunction with the route-map command to be able to define the match criteria for route leaking. Consider a scenario where you have created two VRF tables VRF-red and VRF-blue. VRF-red exports routes with the export_ospfbgp_protocol route-map to VRF-blue.
The show run output for the above configuration is as follows: ip vrf vrf-Red ip route-export 1:1 export_ospfbgp_protocol ip route-import 2:2 ! this action exports only the OSPF and BGP routes to other VRFs ! ip vrf vrf-Blue ip route-export 2:2 ip route-import 1:1 import_ospf_protocol !this action accepts only OSPF routes from VRF-red even though both OSPF as well as BGP routes are shared The show VRF commands displays the following output: DellEMC# show ip route vrf VRF-Blue C 122.2.2.
67 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is designed to eliminate a single point of failure in a statically routed network. Topics: • • • • • • VRRP Overview VRRP Benefits VRRP Implementation VRRP Configuration Sample Configurations Proxy Gateway with VRRP VRRP Overview VRRP is designed to eliminate a single point of failure in a statically routed network.
Figure 172. Basic VRRP Configuration VRRP Benefits With VRRP configured on a network, end-station connectivity to the network is not subject to a single point-of-failure. End-station connections to the network are redundant and are not dependent on internal gateway protocol (IGP) protocols to converge or update routing tables. In conjunction with Virtual Link Trunking (VLT), you can configure optimized forwarding with virtual router redundancy protocol (VRRP).
NOTE: In a VLT environment, VRRP configuration acts as active-active and if route is not present in any of the VRRP nodes, the packet to the destination is dropped on that VRRP node. Table 138.
The following examples how to configure VRRP. DellEMC(conf)#interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)#vrrp-group 111 DellEMC(conf-if-te-1/1-vrid-111)# The following examples how to verify the VRRP configuration. DellEMC(conf-if-te-1/1)#show conf ! interface TenGigabitEthernet 1/1 ip address 10.10.10.
3. Set the backup switches to version 3. Dell_backup_switch1(conf-if-te-1/1-vrid-100)#version 3 Dell_backup_switch2(conf-if-te-1/2-vrid-100)#version 3 Assign Virtual IP addresses Virtual routers contain virtual IP addresses configured for that VRRP group (VRID). A VRRP group does not transmit VRRP packets until you assign the Virtual IP address to the VRRP group.
priority 255 virtual-address 10.10.10.1 virtual-address 10.10.10.2 virtual-address 10.10.10.3 ! vrrp-group 222 no shutdown The following example shows the same VRRP group (VRID 111) configured on multiple interfaces on different subnets. DellEMC#show vrrp -----------------TenGigabitEthernet 1/1, VRID: 111, Version: 2 Net: 10.10.10.1 VRF: 0 default State: Master, Priority: 255, Master: 10.10.10.
00:00:5e:00:01:6f Virtual IP address: 10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10 Authentication: (none) -----------------TenGigabitEthernet 1/2, VRID: 111, Net: 10.10.2.1 VRF: 0 default State: Master, Priority: 125, Master: 10.10.2.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 601, Gratuitous ARP sent: 2 Virtual MAC address: 00:00:5e:00:01:6f Virtual IP address: 10.10.2.2 10.10.2.
● Prevent any BACKUP router with a higher priority from becoming the MASTER router. INTERFACE-VRID mode no preempt Re-enable preempt by entering the preempt command. When you enable preempt, it does not display in the show commands, because it is a default setting. The following example shows how to disable preempt using the no preempt command.
The following example shows how to change the advertise interval using the advertise-interval command. DellEMC(conf-if-te-1/1)#vrrp-group 111 DellEMC(conf-if-te-1/1-vrid-111)#advertise-interval 10 DellEMC(conf-if-te-1/1-vrid-111)# The following example shows how to verify the advertise interval change using the show conf command. DellEMC(conf-if-te-1/1-vrid-111)#show conf ! vrrp-group 111 advertise-interval 10 authentication-type simple 7 387a7f2df5969da4 no preempt priority 255 virtual-address 10.10.10.
The default is 10. ● (Optional) Display the configuration and the UP or DOWN state of tracked objects, including the client (VRRP group) that is tracking an object’s state. EXEC mode or EXEC Privilege mode show track ● (Optional) Display the configuration and the UP or DOWN state of tracked interfaces and objects in VRRP groups, including the time since the last change in an object’s state.
Virtual IP address: 2007::1 fe80::1 Tracking states for 2 resource Ids: 2 - Up IPv6 route, 2040::/64, priority-cost 20, 00:02:11 3 - Up IPv6 route, 2050::/64, priority-cost 30, 00:02:11 The following example shows verifying the VRRP configuration on an interface.
Sample Configurations Before you set up VRRP, review the following sample configurations. VRRP for an IPv4 Configuration The following configuration shows how to enable IPv4 VRRP. This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes.
R2(conf-if-te-2/31-vrid-99)#virtual 10.1.1.3 R2(conf-if-te-2/31-vrid-99)#no shut R2(conf-if-te-2/31)#show conf ! interface TenGigabitEthernet 2/31 ip address 10.1.1.1/24 ! vrrp-group 99 priority 200 virtual-address 10.1.1.3 no shutdown R2(conf-if-te-2/31)#end R2#show vrrp -----------------TenGigabitEthernet 2/31, VRID: 99, Net: 10.1.1.1 VRF: 0 default State: Master, Priority: 200, Master: 10.1.1.
Figure 174. VRRP for an IPv6 Configuration NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be MASTER even if one of two routers has a higher IP or IPv6 address. The following example shows configuring VRRP for IPv6 Router 2 and Router 3. Configure a virtual link local (fe80) address for each VRRPv3 group created for an interface.
vrrp-group 10 priority 100 virtual-address fe80::10 virtual-address 1::10 no shutdown R2(conf-if-te-1/1)#end R2#show vrrp -----------------TenGigabitEthernet 1/1, IPv6 VRID: 10, Version: 3, Net:fe80::201:e8ff:fe6a:c59f VRF: 0 default State: Master, Priority: 100, Master: fe80::201:e8ff:fe6a:c59f (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 135 Virtual MAC address: 00:00:5e:00:02:0a Virtual IP addre
Both Switch-1 and Switch-2 have three VRF instances defined: VRF-1, VRF-2, and VRF-3. Each VRF has a separate physical interface to a LAN switch and an upstream VPN interface to connect to the Internet. Both Switch-1 and Switch-2 use VRRP groups on each VRF instance in order that there is one MASTER and one backup router for each VRF. In VRF-1 and VRF-2, Switch-2 serves as owner-master of the VRRP group and Switch-1 serves as the backup. On VRF-3, Switch-1 is the owner-master and Switch-2 is the backup.
% Info: The VRID used by the VRRP group 11 in VRF 2 will be 178. S1(conf-if-te-1/2-vrid-101)#priority 100 S1(conf-if-te-1/2-vrid-101)#virtual-address 10.10.1.2 S1(conf-if-te-1/2)#no shutdown ! S1(conf)#interface TenGigabitEthernet 1/3 S1(conf-if-te-1/3)#ip vrf forwarding VRF-3 S1(conf-if-te-1/3)#ip address 20.1.1.5/24 S1(conf-if-te-1/3)#vrrp-group 15 % Info: The VRID used by the VRRP group 15 in VRF 3 will be 243. S1(conf-if-te-1/3-vrid-105)#priority 255 S1(conf-if-te-1/3-vrid-105)#virtual-address 20.1.1.
VLAN Scenario In another scenario, to connect to the LAN, VRF-1, VRF-2, and VRF-3 use a single physical interface with multiple tagged VLANs (instead of separate physical interfaces). In this case, you configure three VLANs: VLAN-100, VLAN-200, and VLAN-300. Each VLAN is a member of one VRF. A physical interface (tengigabitethernet 1/1 ) attaches to the LAN and is configured as a tagged interface in VLAN-100, VLAN-200, and VLAN-300. The rest of this example is similar to the non-VLAN scenario.
Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 2 vrf2 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 419, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
Virtual MAC address: 00:00:5e:00:01:0a Virtual IP address: 20.1.1.100 Authentication: (none) DellEMC#show vrrp vrf vrf2 port-channel 1 -----------------Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 2 vrf2 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 419, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
Figure 176. VRRP for IPv6 Topology NOTE: This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. Be sure you make the necessary changes to support your own IP addresses, interfaces, names, and so on.
NOTE: The virtual IPv6 address you configure should be the same as the IPv6 subnet to which the interface belongs.
00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 DellEMC#show vrrp tengigabitethernet 2/8 TenGigabitEthernet 2/8, IPv6 VRID: 255, Version: 3, Net: fe80::201:e8ff:fe8a:e9ed VRF: 0 default State: Master, Priority: 110, Master: fe80::201:e8ff:fe8a:e9ed (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 120 Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 DellEMC# D
Proxy Gateway with VRRP VLT proxy gateway solves the inefficient traffic trombone problem when VLANs are extended between date centers and when VMs are migrated between the two DCs. Starting from Dell EMC Networking OS 9.14.0.0, VRRP provides a much simpler method to solve the traffic trombone problem. This is achieved by configuring same VRRP group IDs to the extended L3 VLANs and VRRP stays active-active across all four VLT nodes even though they are in two different VLT domains.
NOTE: The following configuration assumes that all VLT-related settings are already present on the respective devices. Sample configuration of C1: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
int ten 1/5/1 port-channel-protocol lacp port-channel 10 mode active no shut int ten 1/4/1 port-channel-protocol lacp port-channel 20 mode active no shut interface port-channel 10 vlt-peer-lag po 10 switchport no shutdown interface port-channel 20 vlt-peer-lag po 20 switchport no shutdown int vlan 100 ip address 100.1.1.2/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.254 priority 100 no shutdown int vlan 200 tagged port-channel 20 no shutdown router ospf 10 network 100.1.
int vlan 100 ip address 100.1.1.3/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.254 priority 100 no shutdown int vlan 200 tagged port-channel 20 no shutdown router ospf 10 network 100.1.1.0/24 area 0 Sample configuration of D2: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
68 Debugging and Diagnostics This chapter describes debugging and diagnostics for the device. Topics: • • • • • • • • • • • Offline Diagnostics Trace Logs Auto Save on Crash or Rollover Last Restart Reason Hardware Watchdog Timer Using the Show Hardware Commands Enabling Environmental Monitoring Troubleshooting Packet Loss Enabling Application Core Dumps Mini Core Dumps Enabling TCP Dumps Offline Diagnostics The offline diagnostics test suite is useful for isolating faults and debugging hardware.
NOTE: The system reboots when the offline diagnostics complete. This is an automatic process. The following warning message appears when you implement the offline stack-unit command: Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y After the system goes offline, you must reload or run the online stack-unit stack-unit-number command for the normal operation. 2. Confirm the offline status.
0 0 0 1 up up up up 13466 13653 up up 13466 13466 Speed in RPM The following example shows the diag command (standalone unit). DellEMC#diag stack-unit 1 Warning - diagnostic execution will cause multiple link flaps on the peer side advisable to shut directly connected ports Proceed with Diags [confirm yes/no]: yes DellEMC#Jan 16 02:22:46: %S4810:0 %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on stack unit 1 00:06:47 : Approximate time to complete the Diags ...
**************************** S4810 LEVEL 0 DIAGNOSTICS************************** diagS4810ChkPsuPresence[625]: ERROR: Psu : 0 is not present Test 1.000 - Psu Power Good Test .................................... Test 1.001 - Psu Power Good Test .................................... Test 1 - Psu Power Good Test ....................................... diagS4810ChkPsuPresence[625]: ERROR: Psu : 0 is not present Test 2.000 - Fan Psu Status test .................................... Test 2.
Table 139. Line Card Restart Causes and Reasons (continued) Causes Displayed Reasons reload soft reset reboot after a crash soft reset Hardware Watchdog Timer The hardware watchdog command automatically reboots an Dell EMC Networking OS switch/router with a single RPM that is unresponsive. This is a last resort mechanism intended to prevent a manual power cycle. Using the Show Hardware Commands The show hardware command tree consists of commands used with the system.
show hardware stack-unit {1–6} stack-port {portnumber} ● View the counters in the field processors of the stack unit. EXEC Privilege mode show hardware stack-unit {1–6} unit {0-1} counters ● View the details of the FP Devices and Hi gig ports on the stack-unit. EXEC Privilege mode show hardware stack-unit {1–6} unit {0-1} details ● Execute a specified bShell command from the CLI without going into the bShell.
QSFP 52 Voltage High Alarm threshold QSFP 52 Bias High Alarm threshold QSFP 52 RX Power High Alarm threshold QSFP 52 Temp Low Alarm threshold QSFP 52 Voltage Low Alarm threshold QSFP 52 Bias Low Alarm threshold QSFP 52 RX Power Low Alarm threshold =================================== QSFP 52 Temp High Warning threshold QSFP 52 Voltage High Warning threshold QSFP 52 Bias High Warning threshold QSFP 52 RX Power High Warning threshold QSFP 52 Temp Low Warning threshold QSFP 52 Voltage Low Warning threshold QSFP
3. After the software has determined that the temperature levels are within normal limits, you can re-power the card safely. To bring back the line card online, use the power-on command in EXEC mode. In addition, to control airflow for adequate system cooling, Dell EMC Networking requires that you install blanks in all slots without a line card. NOTE: Exercise care when removing a card; if it has exceeded the major or shutdown thresholds, the card could be hot to the touch.
Troubleshooting Packet Loss The show hardware stack-unit command is intended primarily to troubleshoot packet loss. To ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● troubleshoot packet loss, use the following commands.
HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS on COS10 HOL DROPS on COS11 HOL DROPS on COS12 HOL DROPS on COS13 HOL DROPS on COS14 HOL DROPS on COS15 HOL DROPS on COS16 HOL DROPS on COS17 TxPurge CellErr Aged Drops --- Egress MAC counters--Egress FCS Drops --- Egress FORWARD PROCESSOR IPv4 L3UC Aged & Drops TTL Threshold Drops INVALID VLAN CNTR Drops L2MC Drops PKT Drops of ANY Conditions Hg MacUnderflow TX Err PKT Counter --- Error counters--Internal Ma
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 49 49 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 16 0 0 0 0 17 2144854 0 124904297 0 18 0 0 0 0 19 0 0 0 0 20 0 0 0 0 21 0 0 0 0 22 0 0 0 0 23 0 0 0 0 24 0 0 0 0 25 0 0 0 0 26 0 0 0 0 27 0 0 0 0 28 0 0 0 0 29 0 0 0 0 30 0 0 0 0 31 0 0 0 0 32 0 0 0 0 33 0 0 0 0 34 0 0 0 0 35 0 0
49 52 52 52 52 53 53 53 53 54/1 54/2 54/3 54/4 0 0 0 0 0 0 0 0 0 0 0 0 0 Internal 0 Internal 0 52 0 0 0 0 61 0 0 0 0 62 0 0 0 0 63 0 0 0 0 64 0 0 0 0 65 0 0 0 0 66 0 0 0 0 67 0 0 0 0 68 0 0 0 0 69 0 0 0 0 70 0 0 0 0 71 0 0 0 0 72 0 0 0 0 53 0 0 0 0 57 4659499 0 0 0 Dataplane Statistics The show hardware stack-unit cpu data-plane statistics command provides insight into the packet types coming to the CPU.
txRequested :12698 noTxDesc :0 txError :0 txReqTooLarge :0 txInternalError :0 txDatapathErr :0 txPkt(COS0 ) :0 txPkt(COS1 ) :0 txPkt(COS2 ) :0 txPkt(COS3 ) :0 txPkt(COS4 ) :0 txPkt(COS5 ) :0 txPkt(COS6 ) :0 txPkt(COS7 ) :0 txPkt(COS8 ) :0 txPkt(COS9 ) :0 txPkt(COS10) :0 txPkt(COS11) :0 txPkt(UNIT0) :0 Example of Viewing Party Bus Statistics DellEMC#sh hardware stack-unit 1 cpu party-bus statistics Input Statistics: 27550 packets, 2559298 bytes 0 dropped, 0 errors Output Statistics: 1649566 packets, 19353162
Description RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Frame Counter RX - IPV6 L3 routed multicast Packets RX - Unicast Packet Counter RX - 64 Byte Frame Counter RX - 64 to 127 Byte Frame Counter RX - 128 to 255 Byte Frame Counter RX - 256 to 511 Byte Frame Counter RX - 512 to 1023 Byte Frame Counter RX - 1024 to 1518 Byte Frame Counter RX - 1519 to 1522 Byte Good VLAN Frame Counter RX - 1519 to 2047 Byte Frame Counter RX - 2048 to 4095 Byte Frame Counter R
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - 64 Byte Frame Counter 64 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Frame Counter Good Packet Counter Packet/frame Counter Unicast
RX - Unicast Frame Counter RX - Multicast Frame Counter RX - Broadcast Frame Counter RX - Byte Counter RX - Control Frame Counter RX - Pause Control Frame Counter RX - Oversized Frame Counter RX - Jabber Frame Counter RX - VLAN Tag Frame Counter RX - Double VLAN Tag Frame Counter RX - RUNT Frame Counter RX - Fragment Counter RX - VLAN Tagged Packets RX - Ingress Dropped Packet RX - MTU Check Error Frame Counter RX - PFC Frame Priority 0 RX - PFC Frame Priority 1 RX - PFC Frame Priority 2 RX - PFC Frame Prio
2 3 4 drwx drwx -rwx 4096 4096 512 Jan 01 1980 00:00:00 +00:00 .. Jan 07 2015 13:25:04 +00:00 FTP_STK_MEMBER May 11 2015 20:54:24 +00:00 f10StkUnit.kcore.mini.
69 Standards Compliance This chapter describes standards compliance for Dell EMC Networking products. NOTE: Unless noted, when a standard cited here is listed as supported by the Dell EMC Networking OS, the system also supports predecessor standards. One way to search for predecessor standards is to use the http://tools.ietf.org/ website. Click “Browse and search IETF documents,” enter an RFC number, and inspect the top of the resulting document for obsolescence citations to related RFCs.
RFC and I-D Compliance Dell EMC Networking OS supports the following standards. The standards are grouped by related protocol. The columns showing support by platform indicate which version of Dell EMC Networking OS first supports the standard. General Internet Protocols The following table lists the Dell EMC Networking OS support per platform for general internet protocols. Table 141.
Table 141. General Internet Protocols (continued) R F C # Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 6 0 Transfer Protocol 2 4 7 4 Definition of 7.7.1 the Differentiate d Services Field (DS Field) in the IPv4 and IPv6 Headers 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2 PPP over 61 SONET/SD 5 H 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2 6 9 8 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.
Table 142. General IPv4 Protocols (continued) RF C# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 103 DOMAIN NAMES 5 IMPLEMENTATION AND SPECIFICATION (client) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 104 A Standard for the 2 Transmission of IP Datagrams over IEEE 802 Networks 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 1191 Path MTU Discovery 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.
Table 143. General IPv6 Protocols (continued) RFC Full Name # S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 246 2 (Par tial) IPv6 Stateless Address Autoconfiguration 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 246 4 Transmission of IPv6 Packets over Ethernet Networks 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 267 5 IPv6 Jumbograms 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2711 IPv6 Router Alert Option 8.3.12.0 9.8(0.
Table 144. Border Gateway Protocol (BGP) (continued) RFC# Full Name SSeries/ZSeries S3048–ON S4048–ON Z9100–ON S4048TON S6010–ON 2842 Capabilities Advertisement with BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2858 Multiprotocol Extensions for BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2918 Route Refresh Capability for BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 3065 Autonomous System Confederations for BGP 7.8.1 9.
Intermediate System to Intermediate System (IS-IS) The following table lists the Dell EMC Networking OS support per platform for IS-IS protocol. Table 146. Intermediate System to Intermediate System (IS-IS) RFC# Full Name S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1142 OSI IS-IS Intra-Domain Routing Protocol (ISO DP 10589) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 1195 Use of OSI IS-IS for Routing in TCP/IP and Dual Environments 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.
Routing Information Protocol (RIP) The following table lists the Dell EMC Networking OS support per platform for RIP protocol. Table 147. Routing Information Protocol (RIP) RF C# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 105 8 Routing Information Protocol 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 245 RIP Version 3 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 4191 Default Router Preferences and More-Specific Routes 8.3.12.0 9.8(0.
Table 149. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1156 Management Information Base for Network Management of TCP/IP-based internets 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 1157 A Simple Network Management 7.6.1 Protocol (SNMP) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 1212 Concise MIB Definitions 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.
Table 149. Network Management (continued) RFC# Full Name 2575 S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON View-based Access Control 7.6.1 Model (VACM) for the Simple Network Management Protocol (SNMP) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 2576 Coexistence Between Version 1, Version 2, and Version 3 of the Internet-standard Network Management Framework 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.
Table 149. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON Network Management Protocol (SNMP) 3418 Management Information Base (MIB) for the Simple Network Management Protocol (SNMP) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 3434 Remote Monitoring MIB Extensions for High Capacity Alarms, High-Capacity Alarm Table (64 bits) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 3580 IEEE 802.
Table 149. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON IEEE Management Information Base 802.1A module for LLDP configuration, B statistics, local system data and remote systems data components. 7.7.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) IEEE The LLDP Management 802.1A Information Base extension B module for IEEE 802.1 organizationally defined discovery information. (LLDP DOT1 MIB and LLDP DOT3 MIB) 7.7.1 9.8(0.0P2) 9.8(0.
Table 149. Network Management (continued) RFC# Full Name FORC E10-IFEXTEN SIONMIB S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON Force10 Enterprise IF Extension 7.6.1 MIB (extends the Interfaces portion of the MIB-2 (RFC 1213) by providing proprietary SNMP OIDs for other counters displayed in the "show interfaces" output) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) FORC E10LINKA GGMIB Force10 Enterprise Link Aggregation MIB 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.
Table 149. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON ALAR M-MIB MIB Location You can find Force10 MIBs under the Force10 MIBs subhead on the Documentation page of iSupport: https://www.force10networks.com/CSPortal20/KnowledgeBase/Documentation.aspx You also can obtain a list of selected MIBs and their OIDs at the following URL: https://www.force10networks.com/CSPortal20/Main/Login.aspx Some pages of iSupport require a login.
70 X.509v3 supports X.509v3 standards. Topics: • • • • • • • • • Introduction to X.509v3 certificates X.509v3 support in Information about installing CA certificates Information about Creating Certificate Signing Requests (CSR) Information about installing trusted certificates Transport layer security (TLS) Online Certificate Status Protocol (OSCP) Verifying certificates Event logging Introduction to X.509v3 certificates X.
Advantages of X.509v3 certificates Public key authentication is preferred over password-based authentication, although both may be used in conjunction, for various reasons. Public-key authentication provides the following advantages over normal password-based authentication: ● Public-key authentication avoids the human problems of low-entropy password selection and provides more resistance to brute-force attacks than password-based authentication.
The other hosts on the network, such as the SUT switch, syslog server, and OCSP server, generate private keys and create Certificate Signing Requests (CSRs). The hosts then upload the CSRs to the Intermediate CA or make the CSRs available for the Intermediate CA to download. generates a CSR using the crypto cert generate request command. The hosts on the network (SUT, syslog, OCSP…) also download and install the CA certificates from the Root and Intermediate CAs.
After the CA certificate is installed, the system can secure communications with TLS servers by verifying certificates that are signed by the CA. Installing CA certificate To install a CA certificate, enter the crypto ca-cert install {path} command in Global Configuration mode. Information about Creating Certificate Signing Requests (CSR) Certificate Signing Request (CSR) enables a device to get a X.509v3 certificate from a CA. In order for a device to get a X.
● ● ● ● ● Common Name Email address Validity Length Alternate Name NOTE: The command contains multiple options with the Common Name being a required field and blanks being filled in for unspecified fields. Information about installing trusted certificates Dell EMC Networking OS also enables you to install a trusted certificate. The system can then present this certificate for authentication to clients such as SSH and HTTPS.
TLS_DHE_RSA_WITH_AES_128_CBC_SHA TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_ECDH_RSA_WITH_AES_256_CBC_SHA TLS_ECDH_RSA_WITH_AES_128_CBC_SHA TLS_DH_RSA_WITH_AES_256_CBC_SHA TLS_DH_RSA_WITH_AES_128_CBC_SHA TLS compression is disabled by default. TLS session resumption is also supported to reduce processor and traffic overhead due to public key cryptographic operations and handshake traffic.
Configuring OCSP behavior You can configure how the OCSP requests and responses are signed when the CA or the device contacts the OCSP responders. To configure this behavior, follow this step: In CONFIGURATION mode, enter the following command: crypto x509 ocsp {[nonce] [sign-request]} Both the none and sign-request parameters are optional. The default behavior is to not use these two options.
Verifying Client Certificates Verifying client certificates is optional in the TLS protocol and is not explicitly required by Common Criteria. However, TLS-protected Syslog and RADIUS protocols mandate that certificate-based mutual authentication be performed. Event logging The system logs the following events: ● A CA certificate is installed or deleted. ● A self-signed certificate and private key are generated. ● An existing host certificate, a private key, or both are deleted.
