Users Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Dell EMC Networking Command Line

Reference Guide for the S5048F–ON System

9.14.2.8

September 2020

Rev. A00

Summary of content (1733 pages)

PAGE 1
Dell EMC Networking Command Line Reference Guide for the S5048F–ON System 9.14.2.8 September 2020 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide.........................................................................................................39 Objectives........................................................................................................................................................................... 39 Audience..............................................................................................................................................................................
PAGE 4
banner login........................................................................................................................................................................ 83 banner motd....................................................................................................................................................................... 85 cam-acl...........................................................................................................................................
PAGE 5
show software ifm...........................................................................................................................................................142 show system..................................................................................................................................................................... 143 show tech-support..........................................................................................................................................
PAGE 6
feature aclrange......................................................................................................................................................... 189 ip access-group.......................................................................................................................................................... 189 ipv6 access-group...................................................................................................................................................
PAGE 7
match as-path............................................................................................................................................................ 251 match community..................................................................................................................................................... 252 match interface.........................................................................................................................................................
PAGE 8
ipv6 router ospf................................................................................................................................................................313 bfd all-neighbors.............................................................................................................................................................. 314 bfd disable.............................................................................................................................................
PAGE 9
bgp client-to-client reflection.................................................................................................................................351 bgp cluster-id..............................................................................................................................................................351 bgp confederation identifier...................................................................................................................................
PAGE 10
neighbor route-reflector-client..............................................................................................................................398 neighbor send-community...................................................................................................................................... 399 neighbor shutdown...................................................................................................................................................
PAGE 11
cam-acl-egress.......................................................................................................................................................... 456 cam-optimization...................................................................................................................................................... 456 feature ipv6acloptimized.........................................................................................................................................
PAGE 12
debug dcbx................................................................................................................................................................. 492 fcoe priority-bits........................................................................................................................................................493 show interface dcbx detail......................................................................................................................................
PAGE 13
excluded-address......................................................................................................................................................550 hardware-address......................................................................................................................................................551 host-address...............................................................................................................................................................
PAGE 14
hash-algorithm.................................................................................................................................................................587 ip ecmp-group................................................................................................................................................................. 590 ip ecmp weighted..........................................................................................................................................
PAGE 15
show show show show config...................................................................................................................................................................... 629 garp timers............................................................................................................................................................ 630 gvrp..........................................................................................................................................
PAGE 16
interface...................................................................................................................................................................... 676 interface group...........................................................................................................................................................677 interface loopback............................................................................................................................................
PAGE 17
Chapter 23: IPv4 Routing...........................................................................................................743 arp....................................................................................................................................................................................... 744 arp backoff-time..............................................................................................................................................................
PAGE 18
show show show show show show ip protocols............................................................................................................................................................ 798 ip route................................................................................................................................................................... 799 ip route list.......................................................................................................................
PAGE 19
graceful-restart ietf........................................................................................................................................................848 graceful-restart interval................................................................................................................................................ 849 graceful-restart restart-wait....................................................................................................................................
PAGE 20
iscsi aging time................................................................................................................................................................ 896 iscsi cos............................................................................................................................................................................. 896 iscsi enable....................................................................................................................................
PAGE 21
fefd mode....................................................................................................................................................................938 fefd reset.................................................................................................................................................................... 939 fefd-global interval........................................................................................................................................
PAGE 22
ip msdp sa-filter............................................................................................................................................................... 981 ip msdp sa-limit................................................................................................................................................................982 ip msdp shutdown.......................................................................................................................................
PAGE 23
clear ip mroute.......................................................................................................................................................... 1013 ip mroute.................................................................................................................................................................... 1014 ip multicast-limit............................................................................................................................................
PAGE 24
track ipv6 route metric threshold........................................................................................................................1057 track ipv6 route reachability.................................................................................................................................1058 track resolution ipv6 route....................................................................................................................................
PAGE 25
show ip ospf database............................................................................................................................................ 1105 show ip ospf database asbr-summary.................................................................................................................1106 show ip ospf database external............................................................................................................................ 1108 show ip ospf database network....
PAGE 26
show ipv6 ospf neighbor........................................................................................................................................ 1169 snmp context.............................................................................................................................................................1170 timers spf...................................................................................................................................................................
PAGE 27
show running-config monitor session....................................................................................................................... 1214 source (port monitoring)..............................................................................................................................................1215 Chapter 42: Private VLAN (PVLAN).......................................................................................... 1218 ip local-proxy-arp...................................
PAGE 28
policy-map-output...................................................................................................................................................1259 qos-policy-input....................................................................................................................................................... 1260 qos-policy-output.....................................................................................................................................................
PAGE 29
ip split-horizon............................................................................................................................................................... 1309 maximum-paths............................................................................................................................................................. 1309 neighbor...................................................................................................................................................
PAGE 30
accounting.................................................................................................................................................................1356 aaa radius group.......................................................................................................................................................1357 show accounting.....................................................................................................................................................
PAGE 31
dot1x authentication (Configuration).................................................................................................................. 1401 dot1x authentication (Interface)...........................................................................................................................1401 dot1x auth-fail-vlan................................................................................................................................................. 1402 dot1x auth-server........
PAGE 32
ip dhcp snooping vlan............................................................................................................................................. 1443 show ip dhcp snooping...........................................................................................................................................1444 Role-Based Access Control Commands..................................................................................................................
PAGE 33
snmp-server contact.............................................................................................................................................. 1483 snmp-server enable traps......................................................................................................................................1484 snmp-server engineID............................................................................................................................................
PAGE 34
clear storm-control pfc drop-counters.................................................................................................................... 1547 show storm-control pfc statistics............................................................................................................................. 1548 clear storm-control pfc statistics..............................................................................................................................
PAGE 35
email-address............................................................................................................................................................1584 phone..........................................................................................................................................................................1584 preferred-method..............................................................................................................................................
PAGE 36
downstream.................................................................................................................................................................... 1622 downstream auto-recover...........................................................................................................................................1623 downstream disable links.............................................................................................................................................
PAGE 37
show vlt backup-link.....................................................................................................................................................1664 show vlt counters..........................................................................................................................................................1665 show vlt detail...................................................................................................................................................
PAGE 38
Chapter 64: Virtual Router Redundancy Protocol (VRRP)........................................................ 1700 IPv4 VRRP Commands.................................................................................................................................................1700 advertise-interval.....................................................................................................................................................1700 authentication-type......................................
PAGE 39
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 40
Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
PAGE 41
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 42
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 43
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter for the interface twentyfiveGigE 1/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
PAGE 44
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
PAGE 45
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
PAGE 46
show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated the command to display the IPV6acloptimized feature on the S6100– ON and Z9100–ON. 9.12(1.
PAGE 47
To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command. CONFIGURATION Mode In EXEC Privilege mode, use the configure command to enter CONFIGURATION mode and configure routing protocols and access interfaces. To enter CONFIGURATION mode: 1. Verify that you are logged in to EXEC Privilege mode. 2.
PAGE 48
You can return to CONFIGURATION mode by using the exit command. EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode.
PAGE 49
To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port[/subport] number.
PAGE 50
LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information, see Link Layer Discovery Protocol (LLDP). To enter LLDP mode: 1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode. 2. Enter the protocol lldp command. The prompt changes to include conf-lldp or conf-if-interface-lldp.
PAGE 51
To enter MULTIPLE SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree mstp command. The prompt changes to include conf-mstp. You can return to CONFIGURATION mode by using the exit command. OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 52
2. Enter the protocol gvrp command. The prompt changes to include config-gvrp. You can return to CONFIGURATION mode by using the exit command. RAPID SPANNING TREE (RSTP) Mode To enable and configure RSTP, use RSTP mode. For more information, see Rapid Spanning Tree Protocol (RSTP). To enter RSTP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree rstp command. The prompt changes to include conf-rstp.
PAGE 53
ROUTER OSPFV3 Mode To configure OSPF for IPv6, use ROUTER OSPFV3 mode. To enter ROUTER OSPFV3 mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ipv6 router ospf {process-id} command. The prompt changes to include conf-ipv6-router_ospf. You can return to CONFIGURATION mode by using the exit command. ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, see Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1.
PAGE 54
2. Enter the vlt domain command, and then the VLT domain number. The prompt changes to include conf-vlt-domain. You can return to CONFIGURATION mode by entering the exit command. VRRP Mode To enable and configure Virtual Router Redundancy Protocol (VRRP), use VRRP mode. For more information, see Virtual Router Redundancy Protocol (VRRP). To enter VRRP mode: 1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command, and then enter the VRRP group ID.
PAGE 55
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 56
secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system. nfsmount://filepath system: Enter the keyword system: to retrieve the image from the system. usbflash Enter the keyword usbflash: to retrieve the image from the USB flash memory. usbflash://filename.
PAGE 57
Parameters flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB. directory name and path Enter the directory name and path as follows: directory name ([[flash://]directory_path]) NOTE: The cd command without any arguments will change the current directory to flash: Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 58
running-config Enter the keywords running-config to copy from the current system configuration. scp: Enter the keyword scp: to copy from the remote file system, IPv4, or IPv6, (scp://userid:password@hostip/filepath). startup-config Enter the keywords startup-config to copy from the startup configuration. tftp: Enter the keyword tftp: to copy from the remote file system, IPv4, or IPv6, (tftp://hostip/filepath). usbflash: Enter the keyword usbflash: to copy the file to or from the external USB flash.
PAGE 59
When you load the startup configuration or a configuration file from a network server such as TFTP to the running configuration, the configuration is added to the running configuration. This does not replace the existing running configuration. Commands in the configuration file has precedence over commands in the running configuration. Dell EMC Networking OS supports copying the running-configuration to a TFTP server, an FTP server, or a remote NFS file system.
PAGE 60
Related Commands ● cd – changes the working directory. delete Delete a file from the flash. After deletion, files cannot be restored. Syntax delete {flash: | nfsmount: | usbflash:} [no-confirm] Parameters flash: To delete a file or directory on the internal flash, enter flash:// then the filename or directory name ([flash://]filepath). nfsmount: To delete a file or directory on the NFS-mounted file system, enter nfsmount:// then the mount point and the file path (nfsmount://filepath).
PAGE 61
dir Display the files in a file system. The default is the current directory. Syntax Parameters dir [flash: | nfsmount: | usbflash:] flash: For a directory on the internal Flash, enter flash:// directory name. nfsmount: For a file or directory on an NFS-mounted file system, enter nfsmount:// then the mount point and file path. NOTE: While displaying a file directory on a remote NFS file system, it is mandatory to specify the mount-point that indicates the working directory on the NFS file system.
PAGE 62
flash: 2056916992 bytes total (2052784128 bytes free) DellEMC# Example (NFS Mount) DellEMC# dir nfsmount: Directory of nfsmount: 1 2 drwx drwx 512 512 Jun 15 2015 02:47:57 +00:00 . Jun 15 2015 02:47:57 +00:00 .. nfsmount: 1463410688 bytes total (585719808 bytes free) DellEMC# Related Commands ● cd — changes the working directory. format Erase all existing files and reformat the file system. After the file system is formatted, files cannot be restored.
PAGE 63
fsck flash Checks the flash file system for errors. Syntax Parameters Defaults fsck {flash: | usbflash:} flash: For a directory on the internal Flash, enter flash:// directory name. usbflash: For a directory on the external USB flash, enter usbflash:// directory name. None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 64
Example Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. DellEMC# mkdir nfsmount:/nfs-mountpoint/guest DellEMC# ● rmdir — remove a directory.
PAGE 65
Related Commands ● cd — change the working directory. rmdir Removes a directory from the NFS mounted file system. Syntax rmdir nfsmount://mount-point/usrname Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 66
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.
PAGE 67
Example Version Description 8.3.11.1 Introduced on the Z9000 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series and E-Series. DellEMC#show boot system stack-unit 1 Current system image information in the system: =============================================== Type Boot Type A B ---------------------------------------------------stack-unit 1 FLASH BOOT 9.12(1.0) 9.12(1.0) [boot] DellEMC# show bootvar Display the variable settings for the boot parameters.
PAGE 68
PRIMARY HOST CONFIG FILE = variable does not exist SECONDARY HOST CONFIG FILE = variable does not exist PRIMARY NETWORK CONFIG FILE = variable does not exist SECONDARY NETWORK CONFIG FILE = variable does not exist CURRENT IMAGE FILE = system://B CURRENT CONFIG FILE 1 = flash://startup-config CURRENT CONFIG FILE 2 = variable does not exist CONFIG LOAD PREFERENCE = local first BOOT INTERFACE GATEWAY IP ADDRESS = 10.16.132.
PAGE 69
Command Fields Field Description size(b) Lists the size (in bytes) of the storage location. If the location is remote, no size is listed. Free(b) Lists the available size (in bytes) of the storage location. If the location is remote, no size is listed. Feature Displays the formatted DOS version of the device. Type Displays the type of storage. If the location is remote, the word network is listed. Flags Displays the access available to the storage location.
PAGE 70
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. DellEMC#show os-version RELEASE IMAGE INFORMATION : --------------------------------------------------------------------Platform Version Size ReleaseTime S-Series:S5048F-ON 9.12(1.
PAGE 71
boot for the current boot configuration cam-profile for the current CAM profile in the configuration class-map for the current class-map configuration communitylist for the current community-list configuration ecmp-group for the current ECMP group configuration eis for the current EIS configuration ethernet for the current Ethernet CFM configuration fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current
PAGE 72
for the current input policy map configuration policy-mapoutput for the current output policy map configuration po-failovergroup for the current port-channel failover-group configuration prefix-list for the current prefix-list configuration privilege for the current privilege configuration qos-policyinput for the current input QoS policy configuration qos-policyoutput for the current output QoS policy configuration radius for the current RADIUS configuration redirect-list for the current red
PAGE 73
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 74
Example Usage Information DellEMC# show running-config status running-config bytes 10257, checksum 0xFD33339F startup-config bytes 10257, checksum 0xFD33339F The status option allows you to display the size and checksum of the running configuration and the startup configuration. show startup-config Display the startup configuration. Syntax show startup-config Command Modes EXEC Privilege Command History Example 74 This guide is platform-specific.
PAGE 75
Related Commands ● show running-config – displays the current (running) configuration. show version Display the current Dell EMC Networking Operating System (OS) version information on the system. Syntax show version Command Modes EXEC Privilege Command History Command Fields This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 76
Example (Z5048F–ON) Lines Beginning With Description System image... Image file name System Type: System name Control Processor:... Control processor information and amount of memory on processor 128K bytes... Amount and type of memory on system 1 Route Processor... Hardware configuration of the system, including the number and type of physical interfaces available DellEMC#show version Dell EMC Real Time Operating System Software Dell EMC Operating System Version: 2.
PAGE 77
Defaults A: Enter the keyword A to upgrade the bootflash partition A:. B: Enter the keyword B to upgrade the bootflash partition B:. none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Example Version Description 9.12(1.
PAGE 78
Defaults ftp: Enter the keyword ftp to follow it with the location of the source file in this form: //userid:password@hostip/filepath, or press Enter to launch a prompt sequence. tftp: Enter the keyword tftp to follow it with the location of the source file in this form: //hostlocation/filepath, or press Enter to launch a prompt sequence. flash: Enter the keyword flash to follow it with the location of the source file in this form: //filepath, or press Enter to launch a prompt sequence.
PAGE 79
Defaults flash:// (Optional). Enter the flash:// keyword. The default is to use the flash drive. You can just enter the image file name. img-file Enter the name the Dell EMC Networking software image file to validate. hash-value (Optional). Enter the relevant hash published on i-Support. flash drive Command Modes EXEC mode Command History Usage Information Version 9.5.(0.0) Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 80
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
PAGE 81
• • • • • • • • • • • • • • • • • show processes cpu show processes ipc flow-control show processes memory show reload-type show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit stack-unit location-led telnet telnet-peer-stack-unit terminal length traceroute undebug all virtual-ip write alias Configure shorter alias names for single-line command input. Syntax alias alias-name command To undo the configuration, use the no alias alias-name command command.
PAGE 82
Example The following example shows how to configure single-line alias-name: DellEMC#configure terminal DellEMC(conf)# alias-definition DellEMC(conf-alias-definition)# alias showipbr10 show ip interface brief The following example shows how to configure aliases with arguments in EXEC mode: DellEMC#configure terminal DellEMC(conf)# alias-definition DellEMC(conf-alias-definition)# alias procpu show processes cpu management-unit | grep $1 DellEMC(conf-alias-definition)# alias intbr show ip interface brief | g
PAGE 83
Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 84
Enter no banner login to delete the banner text. Enter no banner login keyboardinteractive to automatically go to the banner message prompt (does not require a carriage return). Parameters keyboardinteractive Enter the keyboard-interactive keyword and then press Enter (carriage return) to retrieve the message banner prompt. acknowledgemen Enter the acknowledgement keyword to require a positive acknowledgement t from the user while logging in to the system.
PAGE 85
login prompt keyboard-interactive Prompt will be displayed by default If you configure the acknowledgement keyword, the system requires a positive acknowledgement from the user while logging in to the system. $ telnet 10.11.178.16 Trying 10.11.178.16... Connected to 10.11.178.16. Escape character is '^]'. THIS IS A LOGIN BANNER. PRESS ‘Y’ TO ACKNOWLEDGE. ACKNOWLEDGE? [y/n]: y Login: admin Password: Related Commands ● banner motd — sets a Message of the Day banner.
PAGE 86
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
PAGE 87
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 88
Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.1P1) Introduced on all Dell EMC Networking OS platforms This command resets the average power and average power start time to the current time. Average power and average power start time will be calculated from the reset time (i.e current time). DellEMC#clear average-power stack-unit 1 Proceed to clear Average power ? Confirm [yes/no]:yes DellEMC# clear line Reset a terminal line.
PAGE 89
Version Description E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode. Syntax configure [terminal] Parameters terminal (OPTIONAL) Enter the keyword terminal to specify that you are configuring from the terminal. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 90
Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode. Syntax disable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of the Dell EMC Networking OS. The range is from 0 to 15. The default is 1. 1 Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON.
PAGE 91
Defaults none Command Modes ● CONFIGURATION ● INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 92
Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of Dell EMC Networking OS. The range is from 0 to 15. 15 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 93
Parameters Defaults interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds. The default is 300 seconds (5 minutes). Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 94
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 95
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.
PAGE 96
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 97
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 98
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 99
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 100
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The hostname is used in the prompt. ip ftp password Specify a password for outgoing FTP connections.
PAGE 101
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The password is listed in the configuration file; you can view the password by entering the show running-config ftp command. Use the ip ftp password command when you use the ftp: parameter in the copy command.
PAGE 102
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.
PAGE 103
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Configure a password with the ip ftp password command. Related Commands ● ip ftp password — sets the password for FTP connections.
PAGE 104
ip telnet server enable Enable the Telnet server on the switch. Syntax ip telnet server enable To disable the Telnet server, use the no ip telnet server enable command. Defaults Enabled Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 105
Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 106
Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 107
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 108
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 109
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 110
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. You must have either the System Administrator or Security Administrator privileges to configure login concurrent-session limit or to enable clear-line. To limit the number of concurrent sessions that any user can have on console, auxiliary, and virtual terminal lines, use the login concurrent-session limit number-of-sessions command.
PAGE 111
login statistics Enable and configure user login statistics on console and virtual terminal lines. Syntax login statistics {enable | time-period days} no login statistics {enable | time-period days} Parameters Defaults enable Enables login statistics for the last 30 days by default. time-period days Sets the number of days the system stores user login statistics; range is from 1 to 30. Not configured Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 112
There were 1 successful login attempt(s) for user admin in the last 30 day(s). The preceding message shows that the user had previously logged in to the system using the VTY line from 10.11.178.14. It also displays the number of unsuccessful login attempts since the last login and the number of unsuccessful login attempts in the last 30 days. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'.
PAGE 113
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command ping Test connectivity between the system and another device by sending echo requests and waiting for replies.
PAGE 114
tos (IPv4 only) Enter the type of service required. The range is from 0 to 255. The default is 0. df-bit (IPv4 only) Enter Y or N for the “don't fragment” bit in IPv4 header. ● N: Do not set the “don't fragment” bit. ● Y: Do set “don't fragment” bit Default is No. validate-reply (IPv4 only) Enter Y or N for reply validation. ● N: Do not validate reply data. ● Y: Do validate reply data. Default is No.
PAGE 115
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0)P5 Introduced on the S4048–ON. 9.8(0.0)P2 Introduced on the S3048–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. Added support for the outgoing-interface option for link-local IPv6 addressing on the S4820T. Usage Information 8.3.12.
PAGE 116
Reply to Reply to :: Reply to Reply to Reply to DellEMC# Example (IPv6) request 1 from 172.31.1.216 0 ms request 1 from 172.31.1.205 16 ms request 5 from 172.31.1.209 0 ms request 5 from 172.31.1.66 0 ms request 5 from 172.31.1.87 0 ms DellEMC# ping 100::1 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds: !!!!! Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms) DellEMC# reload Reboot the system.
PAGE 117
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 9.1(0.0) Added ‘conditional’ parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you use only the reload command, the system boots into the Dell EMC Networking OS.
PAGE 118
Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced on the S3048-ON, S4048–ON, S4048T-ON, S6000–ON, S6100–ON, and Z9100–ON Once you enter reload-type, you need to enter the boot-type or secure-erase sub-command required on the next reboot.
PAGE 119
Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(2.6) Introduced on the S3048-ON, S4048–ON, S4048T-ON, S6000–ON, S6100–ON, and Z9100–ON Since secure-erase is enabled by default, once you enter reload-type, you need to enter the no secure-erase command to disable it on the next reboot.
PAGE 120
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. Messages can contain an unlimited number of lines; however, each line is limited to 255 characters. To move to the next line, use . To send the message use CTR-Z; to abort a message, use CTR-C. service timestamps To debug and log messages, add time stamps.
PAGE 121
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 122
cr-vlan interface vlan $1 ..
PAGE 123
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 124
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series 6.2.1.1 Introduced on the E-Series.
PAGE 125
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 126
Command History Usage Information Example (all) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Network OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.1P1) The CLI has been enhanced to show the power, average power and average power start time. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 127
show inventory Display the switch type, components (including media), and Dell EMC Networking Operating System (OS), including hardware identification numbers and configured protocols. Syntax Parameters Defaults show inventory [media slot] media slot (OPTIONAL) Enter the keyword media then the stack ID of the stack member for which you want to display pluggable media inventory. NOTE: This parameter is available but not supported in Dell EMC Networking Operating System version 8.3.11.4.
PAGE 128
1 1 S5048F-ON-FAN S5048F-ON-FAN NA NA 03CH15 03CH15 A00 A00 CN-03CH15-CES00-76O-0184 A00 CN-03CH15-CES00-76O-0185 A00 N/A N/A 0 0 * - Management Unit Software Protocol Configured -------------------------------------------------------------LLDP SNMP DellEMC>show inventory media Slot Port Type Media Serial Number Dell Qualified -----------------------------------------------------------------------------------1 1 Media not present or accessible 1 2 Media not present or accessible 1 3 Media not prese
PAGE 129
Defaults unsuccessfulattempts (Optional)Displays the number of failed login attempts by the current user in the last 30 days or the custom defined time period. user login-id (Optional)Displays the login statistics of a specific user in the last 30 days or the custom defined time period.
PAGE 130
User: admin Last login time: 08:54:28 UTC Wed Mar 23 2016 Last login location: Line vty0 ( 10.16.127.145 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 3 Successful login attempt(s) in last 30 day(s): 4 ----------------------------------------------------------------------------------------------------------------------------------User: admin1 Last login time: 12:49:19 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 131
The following is sample output of the show login statistics successful-attempts command. DellEMC#show login statistics successful-attempts There were 4 successful login attempt(s) for user admin in last 30 day(s). Related Commands ● login statistics — enable and configure user login statistics on console and virtual terminal lines. ● login concurrent-session — configures the limit of concurrent sessions for each user on console and virtual terminal lines.
PAGE 132
show processes cpu Display CPU usage information based on processes running. Syntax show processes cpu [management-unit [1-99 | details] | stack-unit id [1-99]| summary ] Parameters management-unit (OPTIONAL) Display processes running in the control processor. The 1-99 variable [ 1-99 | details] sets the number of tasks to display in order of the highest CPU usage in the past five (5) seconds. Add the keyword details to display all running processes (except sysdlp). Refer to Example (management-unit).
PAGE 133
------------------------------------------UNIT1 3% 3% 1% DellEMC# show processes cpu stack-unit 1 CPUID 5sec 1min 5min -------------------------------------------------CORE 0 13.17 11.53 0.00 CORE 2 9.38 12.16 0.00 Overall 11.28 11.84 0.00 CPU utilization of sysdlp for five seconds: 2%/0%; one minute: 3%; PID Runtime(ms) Invoked uSecs 5Sec 1Min Process 0xbb773000 5950 595 10000 1.00% 2.25% tExcTask 0xbab2a000 4030 403 10000 1.00% 1.33% frrpagt 0xbacf3000 10 1 10000 0.00% 0.
PAGE 134
CORE 2 Overall 9.92 7.25 9.97 6.81 10.52 7.83 CPU utilization of sysdlp for five seconds: 20%/0%; one minute: 17%; five minutes: 18% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 0xba61e020 300870 30087 10000 15.00% 16.33% 16.17% 0 KP 0xba4e4020 35720 3572 10000 4.00% 1.42% 1.35% 0 ifagt_1 0xbb206020 27380 2738 10000 1.00% 0.92% 1.07% 0 tExcTask 0xba576020 500 50 10000 0.00% 0.00% 0.00% 0 envmgr 0xba592020 400 40 10000 0.00% 0.00% 0.00% 0 lcMgr 0xba5b3020 40 4 10000 0.00% 0.00% 0.
PAGE 135
Overall 10.14 PID Runtime(ms) Process 0x00000000 45040 system 0x000001ac 25750 sysdlp 0x0000019a 10650 sysd 0x000003a5 860 clish 0x000001ad 520 lacp 0x000004ba 330 clish 0x000000c9 1240 nvmgr 0x000000e0 530 igmp 0x00000132 420 vrrp 0x0000028d 410 ovsdbsvr 0x000000a9 200 arpm 0x00000253 100 0 otm 0x00000206 140 tnlmgr 0x00000012 1290 mount_mfs 0x0000024d 40 xstp DellEMC# Related Commands 10.74 13.56 Invoked uSecs 5Sec 1Min 4504 10000 13.12% 13.20% 12.94% 0 2575 10000 2.78% 2.48% 3.
PAGE 136
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 137
Example DellEMC# show processes ipc flow-control cp Q Statistics on CP Processor TxProcess RxProcess Cur High Time Retr Len Mark Out ies DHCP0 ACL0 0 1 1 1 DHCP0 IPMGR0 0 0 0 0 DHCP0 IPMGR1 0 0 0 0 DHCP0 IFMGR0 0 0 0 0 IPMGR0 NDPM0 0 0 0 0 IFMGR0 FEFD0 0 10 0 0 IFMGR0 SNMP0 0 1 0 0 IFMGR0 SFL_CP0 0 20 0 0 IFMGR0 PORTMIRR0 0 8 0 0 IFMGR0 EVENTTERMLOG0 0 1 0 0 IFMGR0 IPSECMGR0 0 8 0 0 IFMGR0 DHCP0 0 8 0 0 IFMGR0 IPMGR0 0 29 0 0 IFMGR0 IFAGT3 0 1 0 0 IFAGT3 IFMGR0 0 1 0 0 IFMGR0 OFMGR0 0 16 1 1 IFMGR0 ACL0 0
PAGE 138
show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system. Syntax show processes memory {management-unit | stack unit {unit-id | all | summary}} Parameters management-unit Enter the keyword management-unit for CPU memory usage of the stack management unit. stack unit unit id Enter the keyword stack unit then a stack unit ID of the member unit for which to display memory usage on the forwarding processor.
PAGE 139
show processes memory output Field Description Process Process Name ResSize Actual resident size of the process in memory Size Process test, stack, and data size Allocs Total dynamic memory allocated Frees Total dynamic memory freed Max Maximum dynamic memory allocated Current Current dynamic memory in use The output for the show process memory command displays the memory usage statistics running on CP part (sysd) of the system.
PAGE 140
272 topoDPC 117927936 0 0 271 bcmNHOP 117927936 0 0 270 bcmDISC 117927936 0 0 269 bcmATP-RX 117927936 0 0 268 bcmATP-TX 117927936 0 0 267 bcmSTACK 117927936 0 0 266 bcmRX 117927936 0 0 265 bcmLINK.0 117927936 0 0 !----------- output truncated --------------! DellEMC# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 show reload-type Shows the reload type which occurs on the next reboot.
PAGE 141
Usage Information You can use the show reset-reason without the stack-unit option to view the reason for the last system reboot of the local system. Example — Userinitiated reboot with the reload command DellEMC#show reset-reason Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 Example — System reboot due to the upgrade command DellEMC# show reset-reason Cause: Reboot by Software upgrade Module. Reset Time: 8/9/2017 1:39 PM.
PAGE 142
show software ifm Display interface management (IFM) data. Syntax show software ifm {clients [summary] | ifagt number | ifcb interface | stack-unit unit-ID | trace-flags} Parameters clients Enter the keyword clients to display IFM client information. summary (OPTIONAL) Enter the keyword summary to display brief information about IFM clients. ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics.
PAGE 143
Example Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced for the C-Series and S-Series.
PAGE 144
Example (show system brief) Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, use the show reload-type command. Modified the show system stack-unit command output to support Piece Part ID (PPID). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 145
flash: Save to local flash drive (flash://filename. A maximum of 20 characters. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated to display the show revision and show os-version command outputs. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 146
● ● ● ● Example (options under show techsupport) show show show show Inventory log summary command-history (last 20 commands) log DellEMC# show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command DellEMC#show tech-support stack-unit 1 ? | Pipe through a command DellEMC# show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence of a pattern grep Show only text that matches a pattern no-more Don'
PAGE 147
Type runtime Version 9.14(0.0) Target Control Processor checksum passed BOOT IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target checksum boot flash 3.38.2.6 Control Processor passed BOOTSEL IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target checksum boot selector 3.38.0.
PAGE 148
6 Hundred GigabitEthernet/IEEE 802.3 interface(s) ------------ show clock ------------21:44:30.965 UTC Sat Sep 19 2018 ------------ show running-config ------------Current Configuration ... ! Version 9.12(1.
PAGE 149
stack-unit location-led Toggle the stack unit location LED on or off. Syntax Parameters stack-unit stack-unit-number location—led { off | on} stack-unit stack- Enter the keywords stack-unit and the stack unit number. unit-number on | off Default Turn the stack unit location LED on or off. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 150
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a Null interface, enter the keyword null then the Null interface number. ● For a port channel interface, enter the keywords port-channel then a number. ● For Tunnel interface types, enter the keyword tunnel then the slot/ port information. The range is from 1 to 16383. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 151
telnet-peer-stack-unit Open a Telnet connection to the peer stack unit. Syntax telnet-peer-stack-unit Defaults Not configured. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 152
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 153
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 154
Example (IPv6) DellEMC# traceroute 100::1 Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 100::1, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 100::1 000.000 ms 000.000 ms 000.000 ms DellEMC#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort.
PAGE 155
Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command. virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6-address} command. Parameters ipv4-address Enter the IP address of the active management interface in a dotted decimal format (A.B.C.D.).
PAGE 156
Related Commands ● ip address — assigns a primary and secondary IP address to the interface. write Copy the current configuration to either the startup-configuration file or the terminal. Syntax write [memory [compressed] | terminal] Parameters memory Enter the keyword memory to copy the current running configuration to the startup configuration file. This command is similar to the copy running-config startup-config command.
PAGE 157
When you use the write memory command to copy the running configuration to the startup configuration file with the startup configuration verification feature enabled, the system prompts you to update the hash for the startup configuration using the verified boot hash command.
PAGE 158
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 159
• • • • • dot1x dot1x show show show supplicant-timeout tx-period dot1x cos-mapping interface dot1x interface dot1x profile debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x.
PAGE 160
dot1x auth-fail-vlan Configure an authentication failure VLAN for users and devices that fail 802.1X authentication. Syntax dot1x auth-fail-vlan vlan-id [max-attempts number] To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails.
PAGE 161
dot1x auth-server Configure the authentication server to RADIUS. Syntax dot1x auth-server radius Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 162
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series.
PAGE 163
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface.
PAGE 164
dot1x critical-vlan Configure critical-VLAN for users or devices when authentication server is not reachable. Syntax [no] dot1x critical-vlan vlan-id Parameters Defaults vlan-id Enter the VLAN identifier. The VLAN-ID range is from 1 to 4094. Not Configured. Command Modes INTERFACE INTERFACE (BATCH MODE) Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 165
dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific.
PAGE 166
dot1x host-mode Enable single-host or multi-host authentication. Syntax dot1x host-mode {single-host | multi-host | multi-auth} Parameters Defaults single-host Enable single-host authentication. multi-host Enable multi-host authentication. multi-auth Enable multi-supplicant authentication. single-host Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 167
mac Configure a list of supplicant MAC addresses for dot1x profile represented with a profile-name. Syntax Parameters Defaults [no] mac {mac-address1 mac-address2… mac-address6} mac-address1 mac-address2 … mac-address6 Enter the keyword mac and type the 48– bit MAC addresses using the H.H.H format. A maximum of 6 MAC addresses are allowed. None Command Modes DOT1X PROFILE CONFIG (conf-dot1x-profile) CONFIGURATION TERMINAL BATCH Command History Usage Information This guide is platform-specific.
PAGE 168
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 169
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port.
PAGE 170
dot1x port-control Enable port control on an interface. Syntax dot1x port-control {force-authorized | auto | force-unauthorized} Parameters Defaults force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. None Command Modes Auto Command History Usage Information This guide is platform-specific.
PAGE 171
CONFIGURATION TERMINAL BATCH Error Strings NONE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.
PAGE 172
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command.
PAGE 173
dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters Defaults number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 174
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 175
Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9010.
PAGE 176
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 177
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 178
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series.
PAGE 179
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport][/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 180
Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: DellEMC# Example (macaddress) Enable 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Authenticated Idle DellEMC# show dot1x interface twentyFiveGigE 1/32 mac-address 00:00:00:00:0
PAGE 181
Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: DellEMC# AUTHORIZED(GUEST-VLAN) 100 Authenticated Idle show dot1x profile Display all the dot1x profiles or the details of a specific profile configured in the system.
PAGE 182
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 183
• • deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options. Some commands in this chapter may use similar names, but require different options to support the different ACL types (for example, the deny and permit commands). remark Enter a description for an ACL entry. Syntax remark remark-number description To remove a remark, use the no remark command.
PAGE 184
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode. You can configure up to 4294967291 remarks for a given IP ACL and 65536 remarks for a given MAC ACL. You can include a remark with or without a remark number. If you do not enter a remark number, the remark inherits the sequence number of the last ACL rule.
PAGE 185
● CONFIGURATION-EXTENDED-ACCESS-LIST ● CONFIGURATION-MAC ACCESS LIST-STANDARD ● CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 186
access-class Apply a standard ACL to a terminal line. Syntax access-class access-list-name [ipv4 | ipv6] To remove an ACL, use the no access-class command. Parameters Defaults access-list-name Enter the name of a configured Standard ACL, up to 140 characters. ipv4 Enter the keyword ipv4 to configure an IPv4 access class. ipv6 Enter the keyword ipv6 to configure an IPv6 access class. Not configured. Command Modes LINE Command History Usage Information This guide is platform-specific.
PAGE 187
However, if you already have configured generic IP ACL on a terminal line, then you cannot further apply IPv4 or IPv6 specific filtering on top of this configuration. Because, both IPv4 and IPv6 access classes are already configured on this terminal line. Before applying either IPv4 or IPv6 filtering, first undo the generic configuration using the no access-class access-list-name command.
PAGE 188
clear counters ip access-group Erase all counters maintained for access lists. Syntax clear counters ip access-group [access-list-name] Parameters access-list-name (OPTIONAL) Enter the name of a configured access-list, up to 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 189
Usage Information Example Version Description 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S6100–ON and Z9100–ON. After enabling the acloptimized feature, reboot the system. DellEMC(conf)#feature acloptimized Configuration change will be in effect after save and reload. ACL config containing TTL, layer3 and VRF conflicts with ACL Cam optimzation feature and these keywords would be discarded while applying the ACL. feature aclrange Enable the ACL range option.
PAGE 190
Defaults implicit-permit (OPTIONAL) Enter the keyword implicit-permit to change the default action of the ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). vlan vlan-id (OPTIONAL) Enter the keyword vlan then the ID numbers of the VLANs. The range is from 1 to 4094 (you can use IDs from 1 to 4094). vrf vrf-name (OPTIONAL) Enter the keyword vrf then the ID numbers of the VRFs.
PAGE 191
NOTE: If you apply outbound(egress) IP acl on a switch port, the filter applies only for routed traffic egressing out of that port. To associate an access-list to a non-default VRF, use the vrf attribute of this command. You can use this command at the interface context (physical/LAG) to apply the access-list to a range of VRFs. The VRF MODE is not available for the default and management VRFs. In the Dell EMC Networking OS versions prior to 9.13(0.
PAGE 192
NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces. NOTE: If you apply outbound(egress) IPv6 ACL on a switch port, the filter applies only for routed traffic egressing out of that port. In the Dell EMC Networking OS versions prior to 9.13(0.
PAGE 193
ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 194
Examples To display the list of ACL ranges: DellEMC# show aclrange INDEX PROFILE_NAME TYPE INVERSE LOWER UPPER REF_ THRESHOLD THRESHOLD ---------------------------------------------------------------------------------1 dport1 l4dstport No 80 89 0 2 dport2 l4dstport No 3000 3500 2 3 dportgt5000 l4dstport No 5001 65535 1 4 ip-mtu-782 mtu No 782 782 1 5 sport1 l4srcport No 1024 65535 1 6 sportinv1 l4srcport Yes 2500 2500 1 To display the list of ACLs using the configured range profiles: DellEMC# show aclra
PAGE 195
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Updated the show command output to include monitor option. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.
PAGE 196
deny To drop packets with a certain IP address, configure a filter. Syntax deny {source | any | host {ip-address}} [count [bytes] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command.
PAGE 197
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.
PAGE 198
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.
PAGE 199
Defaults bytes (OPTIONAL) Enter the keyword bytes to count the bytes. log (OPTIONAL) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match the IP DSCP values. The range is from 0 to 63. ecn (OPTIONAL) Enter the keyword ecn to match the ECN bits. The range is from 0 to 3. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry.
PAGE 200
Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide. Related Commands ● deny — assign a IP ACL filter to deny IP packets.
PAGE 201
Usage Information Version Description 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. When you have exhausted all the sequence numbers, this feature permits re-assigning a new sequence number to entries of an existing access-list.
PAGE 202
no-drop Defaults Enter the keywords no-drop to match only the forwarded packets. Not configured Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History Usage Information Related Commands 202 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Removed the session–ID option from the monitor parameter. 9.11(0.
PAGE 203
Extended IP ACL Commands When an ACL is created without any rule and then applied to an interface, ACL behavior reflects an implicit permit. The following commands configure extended IP ACLs, which in addition to the IP address, also examine the packet’s protocol type. The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny Configure a filter that drops IP packets meeting the filter criteria.
PAGE 204
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 205
When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The monitor option is relevant in the context of flow-based monitoring only. For more information, see Port Monitoring. The C-Series and S-Series cannot count both packets and bytes, when you enter the count byte options, only bytes are incremented.
PAGE 206
packet-too-big count parameter-problem count time-exceeded count port-unreachable count The ICMP packets cannot be filtered using mirroring ACL. ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value.
PAGE 207
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.
PAGE 208
● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values.
PAGE 209
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see Flow-based Monitoring in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 210
The C-Series and S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
PAGE 211
● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 212
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 213
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands ● deny — assign a filter to deny IP traffic. ● deny tcp — assign a filter to deny TCP traffic. ip access-list extended Name (or select) an extended IP access list (IP ACL) based on IP addresses or protocols.
PAGE 214
Prior to 7.8.1.0, names are up to 16 characters long. Example Related Commands DellEMC(conf)# ip access-list extended TESTListEXTEND DellEMC(config-ext-nacl)# ● ip access-list standard — configure a standard IP access list. ● show config — display the current configuration. permit To pass IP packets meeting the filter criteria, configure a filter.
PAGE 215
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 216
permit icmp Configure a filter to allow all or specific ICMP messages. Syntax permit icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [type] [dscp] [message-type] [count [byte] | log] [order] [monitor] [fragments] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
PAGE 217
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 218
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 219
The following list includes some common TCP port numbers: ● ● ● ● Defaults 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets the filter processes.
PAGE 220
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 221
permit udp To pass UDP packets meeting the filter criteria, configure a filter. Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [ttl operator] [dscp] [operator port [port]] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 222
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 223
Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry. The range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range. Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 224
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters.
PAGE 225
any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host and then enter the IP address to specify a host IP address or hostname. operator (OPTIONAL) Enter one of the following logical operands: ● ● ● ● ● portnumber eq = equal to neq = not equal to gt = greater than lt = less than range = inclusive range of ports (you must specify two ports for the port parameter.) (OPTIONAL) Enter the application layer port number.
PAGE 226
dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mobile-ip Mobile IP registration (434) nameserver IEN116 name service (obsolete, 42) netbios-dgm NetBios datagram service (138) netbios-ns NetBios name service (137) netbios-ss NetBios session service (139) non500-isakmp Internet Security Association and Key Management Protocol (4500) ntp Network Time Protocol (123) pim-rp-disc PIM-RP-DISC(496
PAGE 227
Defaults fragments Enter the keyword fragments to use ACLs to control packet fragments. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.
PAGE 228
● If you do not configure sequence-number, the rules with the same order value are ordered according to their configuration order. ● If you configure sequence-number, the sequence-number is used as a tie breaker for rules with the same order. When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 229
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. mac access-group Apply a MAC ACL to traffic entering or exiting an interface. You can apply a MAC ACL on a physical, port-channel, or VLAN interface.
PAGE 230
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 231
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 232
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 233
deny To drop packets with a the MAC address specified, configure a filter. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {any | mac-source-address mac-source-address-mask} command. Parameters Defaults any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 234
Usage Information When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands ● permit — configures a MAC address filter to pass packets.
PAGE 235
The number of entries allowed per ACL is hardware-dependent. For detailed specifications about entries allowed per ACL, see your line card documentation. NOTE: Ingress ACLs are supported on C-Series and S-Series platforms only.
PAGE 236
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 237
the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 238
The platform supports both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets that match the filter criteria, configure a filter.
PAGE 239
to the monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 240
cpu-qos Defaults Enter the keywords cpu-qos to assign this ACL to control plane traffic only (CoPP). None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 241
seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands ● mac access-list standard — configure a standard MAC access list. ● show mac accounting access-list — display MAC access list configurations and counters (if configured). permit To pass packets matching the criteria specified, configure a filter.
PAGE 242
Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 243
Defaults Clears “hit” counters for all prefix lists unless a prefix list is specified. Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 244
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 245
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 246
Command Modes PREFIX-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 247
Example Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 248
Example Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show ip prefix-list detail Ip Prefix-list with the last deletion/insertion: PL_OSPF_to_RIP ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 seq 5 permit 1.1.1.
PAGE 249
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show ip prefix-list summary Ip Prefix-list with the last deletion/insertion: PL_OSPF_to_RIP ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 DellEMC# Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit.
PAGE 250
feature executes only after a successful match occurs. If there are no successful matches, the continue feature is ignored. Match clause with Continue clause The continue feature can exist without a match clause. A continue clause without a match clause executes and jumps to the specified route-map entry. With a match clause and a continue clause, the match clause executes first and the continue clause next in a specified route map entry. The continue clause launches only after a successful match.
PAGE 251
Related Commands Version Description 8.1.1.0 Introduced on the E-Series. pre-7.7.1.0 Introduced. ● route-map — enable a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command. Parameters Defaults as-path-name Enter the name of an established AS-PATH ACL, up to 140 characters. Not configured.
PAGE 252
match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Syntax match community community-list-name [exact] To delete a community match filter, use the no match community command. Parameters Defaults community-listname Enter the name of a configured community list. exact (OPTIONAL) Enter the keywords exact to process only those routes with this community list name. Not configured.
PAGE 253
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 254
match ip address To match routes based on IP addresses specified in an access list, configure a filter. Syntax match ip address prefix-list-name To delete a match, use the no match ip address prefix-list-name command. Parameters Defaults prefix-list-name Enter the name of configured prefix list, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific.
PAGE 255
To delete a match, use the no match ip next-hop {prefix-list prefix-list-name} command. Parameters Defaults prefix-list prefix- Enter the keywords prefix-list and then enter the name of configured prefix list-name list, up 10 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 256
Parameters Defaults prefix-list prefix- Enter the keywords prefix-list and then enter the name of configured prefix list-name list, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 257
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 258
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 259
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 260
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 261
Usage Information Example Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 262
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 263
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● set set set set level — specify the OSPF area for route redistribution.
PAGE 264
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The community list used in the set comm-list delete command must be configured so that each filter contains only one community.
PAGE 265
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 266
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 267
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 268
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 269
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● set set set set automatic-tag — compute the tag value of the route.
PAGE 270
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you configure the set next-hop command, its configuration takes precedence over the neighbor next-hop-self command in the ROUTER BGP mode.
PAGE 271
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command. Parameters Defaults tag-value Enter a number as the tag. The range is from zero (0) to 4294967295. Not configured.
PAGE 272
set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Syntax set weight weight To delete a weight specification, use the no set weight weight command. Parameters weight Enter a number as the weight used by the route meeting the route map specification. The range is from 0 to 65535. The default is router-originated = 32768 and all other routes = 0.
PAGE 273
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 274
Example Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.
PAGE 275
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 276
[dscp value] [order] [monitor] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {ip | ip-protocol-number} {source mask | any | host ipaddress} {destination mask | any | host ip-address} command. Parameters ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255.
PAGE 277
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 278
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 279
Parameters ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 280
the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 281
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 282
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 283
permit (for Standard IP ACLs) To permit packets from a specific source IP address to leave the switch, configure a filter. Syntax permit {source [mask]| any | host ip-address} [count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit {source [mask] | any | host ip-address} command.
PAGE 284
You can activate flow-based monitoring for a monitoring session by entering theflow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 285
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 286
operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 287
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 288
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 289
permit (for Standard MAC ACLs) To forward packets from a specific source MAC address, configure a filter. Syntax permit {any | mac-source-address [mac-source-address-mask]} [count [byte]] | [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit {any | mac-source-address mac-source-address-mask} command.
PAGE 290
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 291
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 292
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 293
● permit — assign a permit filter for IP packets. ● permit udp — assign a permit filter for UDP packets. seq (for IP ACLs) Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 294
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 295
udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) . any Enter the keyword any to specify that all routes are subject to the filter. host ipv6- address Enter the keyword host and then enter the IPv6 address to specify a host IP address or hostname.
PAGE 296
The following logical names are supported in UDP: biff Biff (mail notification, comsat, 512) bootpc Bootstrap Protocol (BOOTP) client (68) bootps Bootstrap Protocol (BOOTP) server (67) discard Discard (9) dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mobile-ip Mobile IP registration (434) nameserver IEN116 name service (obsolete, 42) netbios-dgm NetBios datagram service (138) netbios-ns N
PAGE 297
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 298
● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 299
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 300
port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● ● ● ● 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255.
PAGE 301
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 302
For IPv4: echo count echo-reply count host-unreachable count host-unknown count network-unknown count net-unreachable count packet-too-big count parameter-problem count port-unreachable count source-quench count time-exceeded count For IPv6: echo count echo-reply count nd-ns count nd-na count packet-too-big count parameter-problem count time-exceeded count port-unreachable count The ICMP packets cannot be filtered using mirroring ACL.
PAGE 303
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the ttl parameter. 9.11(2.
PAGE 304
● Use the no seq sequence-number command syntax if you know the filter’s sequence number ● Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 305
applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 306
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 307
Parameters source address mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all routes are subject to the filter. host ipv6- Enter the keyword host then the IP address to specify a host IP address. address destination address Enter the IPv6 address of the network or host to which the packets are sent.
PAGE 308
Defaults byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 309
monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG).
PAGE 310
The ICMP packets cannot be filtered using mirroring ACL. ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 311
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 312
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 313
7 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 314
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 315
Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.1P1) Introduced support for enabling BFD on non-default VRFs for OSPFv2 on all the remaining Dell EMC Networking OS platforms.
PAGE 316
NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd disable Disable BFD on an interface. Syntax bfd disable Re-enable BFD using the no bfd disable command. Defaults BFD is disabled by default. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 317
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd enable (Interface) Enable BFD on an interface.
PAGE 318
Parameters interval milliseconds min_rx milliseconds Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200. Enter the keywords min_rx to specify the minimum rate at which the local system would like to receive control packets from the remote system. The range is from 50 to 1000. The default is 200.
PAGE 319
Parameters Defaults ip-address Enter the IP address of the neighbor in dotted decimal format (A.B.C.D). None Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 320
Usage Information Version Description 7.4.1.0 Introduced on the E-Series. Protocol Liveness is a feature that notifies the BFD Manager when a client protocol (for example, OSPF and ISIS) is disabled. When a client is disabled, all BFD sessions for that protocol are torn down. Neighbors on the remote system receive an Admin Down control packet and are placed in the Down state. Peer routers might take corrective action by choosing alternative paths for the routes that originally pointed to this router.
PAGE 321
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.3.(0.0) Introduced on S6000. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on Z9000, S4810, and S4820T. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 322
Usage Information Version Description 9.10(0.2) Introduced support for enabling BFD on non-default VRFs for OSPFv2. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.0 Introduced on the Z9000, S4820T, and S4810.
PAGE 323
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.0 Introduced on the Z9000, S4820T, and S4810. This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode.
PAGE 324
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.2.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 325
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series.
PAGE 326
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series.
PAGE 327
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.1P1) Introduced the vrf keyword on all the remaining Dell EMC Networking OS platforms. 9.10(0.2) Introduced the vrf keyword on the S3048–ON, S4048–ON, S4048T-ON, S6010– ON, Z9100–ON, and S6100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 328
V VT - VRRP - Vxlan Tunnel LocalAddr VRF Clients * 13.1.1.1 2 O Example (Detail) RemoteAddr Interface State Rx-int Tx-int Mult 13.1.1.2 Tf 1/2 Up 200 200 3 * 23.1.1.1 2 O 23.1.1.2 Vl 300 Up 200 200 3 * 33.1.1.1 2 O 33.1.1.2 Vl 301 Up 200 200 3 The following example shows the show bfd vrf neighbors detail command output showing the nondefault VRF called “VRF_blue”. DellEMC# show bfd vrf VRF_blue neighbors detail Session Discriminator: 5 Neighbor Discriminator: 3 Local Addr: 5.1.1.
PAGE 329
Number of messages communicated b/w Manager and Agent: 4 Session Discriminator: 6 Neighbor Discriminator: 1 Local Addr: 7.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 7.1.1.
PAGE 330
Related Commands 330 Version Description 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for VLAN and port-channel interfaces on the E-Series. 7.4.1.0 Introduced on the E-Series. ● show bfd neighbors — display the BFD neighbor information on all interfaces or a specified interface.
PAGE 331
8 Boot Command Line Interface To access this BOOT_USER mode, first boot your Dell EMC Networking platform. When you see the “Press ESC to stop autoboot”, press the ESC key to log into BCLI You enter BOOT_USER mode immediately, as indicated by the BOOT_USER# prompt. NOTE: All commands in this chapter are in Boot_User mode. These commands are supported on the Dell EMC Networking platform. You cannot use the Tab key to complete commands in this mode.
PAGE 332
Command History Usage Information Version Descriptiion 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. After entering the boot change command and selecting the parameters, press Enter. The software prompts you to enter the following: ● The boot device (flash, ftp, tftp, or usbflash), image file name, IP address of the server containing the image, username, and password (only for ftp).
PAGE 333
Command History Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. BOOT_USER #boot message boot messages off BOOT_USER # boot show net config retries Show the number of retries for network boot configuration failure. Syntax boot show net config retries Command Modes BOOT_USER Command History Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 334
boot zero Erase the configured primary, secondary, or default boot image parameters. If you erase all three parameters, the S6000 switch boots from its internal Flash. Syntax boot zero {primary | secondary | default} Parameters Defaults primary Enter the keyword primary to remove the primary boot parameter. secondary Enter the keyword secondary to remove the secondary boot parameter. default Enter the keyword default to remove the default boot parameter.
PAGE 335
Parameters ip-address Enter the IP address of the gateway router in dotted decimal format (A.B.C.D). Command Modes BOOT_USER Command History Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. Usage Information Use the show default-gateway command to view the current default gateway.
PAGE 336
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. When you enter the reload command and the system reboots, you will not be prompted for a password to enter the EXEC Privilege mode (normally you are required to enter the enable command).
PAGE 337
Usage Information In the runtime CLI, use the ip address command in INTERFACE mode to change the Management interface’s IP address. To view the current IP address configured on the Management interface, enter the show interfaces management ethernet command Related Commands show_default-gateway — Display the IP address configured for the default gateway. show_interface_mangement_ethernet— Display the IP address configured for the Management interface. NVRAM erase Erase all NVRAM contents alone.
PAGE 338
serial console Use the serial console to set the serial console baud rate. Syntax serial console Parameters serial console [unit] [baud] Enter the keyword to set the serial port baud rate. The supported values for serial console: ● Unit - 0 ● Baud rate -9600,115200 No defaults. Command Modes BOOT_USER Command History Example Serial Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.
PAGE 339
DEFAULT OPERATING SYSTEM BOOT PARAMETERS: ======================================== boot device : tftp file name : PS-SI-9-0-0-566.bin Management Etherenet IP address : 10.16.133.17 Mask : 255.255.0.0 Server IP address : 10.16.1.200 Default Gateway IP address : 10.16.1.254 BOOT_USER # Related Commands boot_change— Change the primary, secondary, or default boot image configuration. boot_zero — Erase the configured primary, secondary, or default boot image parameters.
PAGE 340
Command History Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. BOOT_USER # show interfaces management ethernet Management ethernet IP address: 10.16.133.17/24 BOOT_ADMIN # On the S6000, the output of this command includes the MAC address and port number of the assigned management port.
PAGE 341
status Enter the keyword status to see the watchdog status. timeout Enter the keyword timeout to see the timeout configured for the watchdog. settimeout Enter the keyword set timeout to set timeout. NOTE: By default, watchdog is disabled. Command Modes BOOT_ADMIN Command History Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000.
PAGE 342
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 343
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 344
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 345
path-count Defaults Enter the number paths supported. The range is from 2 to 64. Disabled Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series.
PAGE 346
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path.
PAGE 347
Example DellEMC(conf)# router bgp DellEMC(conf-router_bgp)#bgp DellEMC(conf-router_bgp)# DellEMC(conf)#do show run 1 asnotation asdot ex | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp
PAGE 348
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation.
PAGE 349
Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 350
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 6.3.1.0 Introduced The MED is a 4-byte unsigned integer value and the default behavior is to assume a missing MED as 4294967295.
PAGE 351
bgp client-to-client reflection Allows you to enable route reflection between clients in a cluster. Syntax bgp client-to-client reflection To disable client-to-client reflection, use the no bgp client-to-client reflection command. Defaults Enabled when a route reflector is configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 352
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 353
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 354
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 355
max-suppresstime (OPTIONAL) Enter the maximum number of minutes a route can be suppressed. The default is four times the half-life value. The range is from 1 to 255. The default is 60 minutes. route-map map- (OPTIONAL) Enter the keyword route-map then the name of a configured route map. name Only match commands in the configured route map are supported. Defaults Disabled. Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History Usage Information This guide is platform-specific.
PAGE 356
Defaults 100 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 357
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. Configuring or un-configuring the command brings down and brings up the BGP Route Manager, this results in tear down and re-establishment of all active sessions. Link Bandwidth has to be configured on the router to tell it to associate Link Bandwidth with prefixes (paths) and/or to use Link Bandwidth in BGP Multipath route selection.
PAGE 358
In the event of an enfore-first-as check failure, the existing BGP session is flapped. Related Commands ● show ip bgp neighbors — view the information the BGP neighbors exchange. ● show ip protocols — view information on routing protocols. bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails.
PAGE 359
To disable fast external failover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 360
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 361
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive.
PAGE 362
bgp recursive-bgp-next-hop Enable next-hop resolution through other routes learned by BGP. Syntax bgp recursive-bgp-next-hop To disable next-hop resolution, use the no bgp recursive-bgp-next-hop command. Defaults Enabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 363
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 364
bgp router-id Assign a user-given ID to a BGP router. Syntax bgp router-id ip-address To delete a user-assigned IP address, use the no bgp router-id command. Parameters Defaults ip-address Enter an IP address in dotted decimal format to reset only that BGP neighbor. The router ID is the highest IP address of the Loopback interface or, if no Loopback interfaces are configured, the highest IP address of a physical interface on the router.
PAGE 365
<0.1-65535.6553 Enter <0.1-65535.65535> to clear peers with the AS number in dot format. 5> A.B.C.D Enter the BGP neighbor address in the A.B.C.D format to clear. X:X:X:X::X Enter the BGP neighbor address in the X:X:X:X::X format to clear. soft (OPTIONAL) Enter the keyword soft to configure and activate policies without resetting the BGP TCP session, that is, BGP Soft Reconfiguration. NOTE: If you enter the clear ip bgp ip-address soft command, both inbound and outbound policies are reset.
PAGE 366
Related Commands ● bgp recursive-bgp-next-hop — disable next-hop resolution through other routes learned by the BGP. clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state.
PAGE 367
clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap. Syntax Parameters clear ip bgp [vrf vrf-name] [ipv4 [multicast | unicast] | ipv6 unicast] [flap-statistics [ipv4-address mask | ipv6–address mask] | filter-list aspath-name | regexp regular-expression] ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to reset only that prefix.
PAGE 368
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information If you enter the clear ip bgp flap-statistics command without any parameters, all statistics are cleared. Related Commands ● show debugging — view the enabled debugging operations. ● show ip bgp flap-statistics — view the BGP flap statistics. ● undebug all — disable all debugging operations.
PAGE 369
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. Syntax debug ip bgp [ vrf vrf-name | A.B.C.D | X:X:X:X::X | peer-group peer-groupname] [in | out] To disable all BGP debugging, use the no debug ip bgp command.
PAGE 370
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.4.(0.
PAGE 371
ipv6 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view dampened-route information related only to ipv6 unicast routes. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 372
Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 373
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 374
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added ipv6 support. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 375
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors.
PAGE 376
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 377
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The default-metric command in BGP sets the value of the BGP MULTI_EXIT_DISC (MED) attribute for redistributed routes only. Related Commands ● bgp always-compare-med — enable comparison of all BGP MED attributes.
PAGE 378
description Enter a description of the BGP routing protocol. Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the BGP protocol (80 characters maximum). none Command Modes ROUTER BGP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 379
Defaults none Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 380
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 381
neighbor add-path This command allows the specified neighbor/peer group to send/receive multiple path advertisements. Syntax Parameters neighbor [ip-address | peer-group-name] add-path [send | receive | both] path-count ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group. Defaults send Enter the keyword send to indicate that the system sends multiple paths to peers.
PAGE 382
peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. seconds Defaults Enter a number as the time interval, in seconds, between BGP advertisements. The range is from 0 to 600 seconds. The default is 5 seconds for internal BGP peers and 30 seconds for external BGP peers. ● seconds = 5 seconds (internal peers) ● seconds = 30 seconds (external peers) Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 383
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 384
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information You cannot set this configuration for a peer that is associated with a peer group.
PAGE 385
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you apply a route map to a BGP peer or neighbor with the neighbor default-originate command configured, the software does not apply the set filters in the route map to that BGP peer or neighbor.
PAGE 386
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 387
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Other BGP filtering commands include: neighbor filter-list, ip as-path access-list, and neighbor route-map. Related Commands ● neighbor route-map — assign a route map to a neighbor or peer group.
PAGE 388
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To prevent loops, the neighbor ebgp-multihop command does not install the default routes of the multihop peer. Networks not directly connected are not considered valid for best-path selection. neighbor fall-over Enable or disable fast fall-over for BGP neighbors.
PAGE 389
neighbor local-as To accept external routes from neighbors with a local AS number in the AS number path, configure Internal BGP (IBGP) routers. Syntax neighbor {ip-address | peer-group-name} local-as as-number [no-prepend] To return to the default value, use the no neighbor {ip-address | peer-group-name} local-as command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 390
neighbor maximum-prefix Control the number of network prefixes received. Syntax neighbor {ip-address | peer-group-name} maximum-prefix maximum [threshold] [warning-only] To return to the default values, use the no neighbor {ip-address | peer-group-name} maximum-prefix maximum command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group.
PAGE 391
show ip bgp summary command displays (prfxd) in the State/PfxRcd column for that neighbor. The neighbor remains down until you enter the clear ip bgp command for the neighbor or the peer group to which the neighbor belongs or you enter the neighbor shutdown and neighbor no shutdown commands. Related Commands ● show ip bgp summary — display the current BGP configuration. neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors.
PAGE 392
Configure the same password on both BGP peers or a connection does not occur. When you configure MD5 authentication between two BGP peers, each segment of the TCP connection between them is verified and the MD5 digest is checked on every segment sent on the TCP connection. Configuring a password for a neighbor causes an existing session to be torn down and a new one established.
PAGE 393
Usage Information Version Description 9.7(0.0) Added the dmzlink-bw parameter. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can assign up to 256 peers to one peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
PAGE 394
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 395
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced the limit keyword on the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. After you configure a peer group as passive, assign it a subnet using the neighbor softreconfiguration inbound command.
PAGE 396
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. To accept 4-byte formats before entering a 4 byte AS Number, configure your system.
PAGE 397
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Applies to EBGP neighbors only. Configure your system to accept 4-byte formats before entering a 4 byte AS Number. If the AS-PATH contains both public and private AS number or contains AS numbers of an EBGP neighbor, the private AS numbers are not removed.
PAGE 398
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted.
PAGE 399
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector, the internal BGP (IBGP) speakers in the network must be fully meshed.
PAGE 400
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To configure a COMMUNITY attribute, use the set community command in ROUTE-MAP mode.
PAGE 401
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group. Use this command with caution as it terminates the specified BGP sessions.
PAGE 402
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings.
PAGE 403
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Timer values configured with the neighbor timers command override the timer values configured with any other command.
PAGE 404
neighbor update-source Enable the E-Series software to use Loopback interfaces for TCP connections for BGP sessions. Syntax neighbor {ip-address | peer-group-name} update-source interface To use the closest interface, use the no neighbor {ip-address | peer-group-name} update-source interface command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group.
PAGE 405
To remove a weight value, use the no neighbor {ip-address | peer-group-name} weight command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group. weight Defaults Enter a number as the weight. The range is from 0 to 65535. The default is 0. 0 Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 406
To remove a network, use the no network ip-address mask [route-map map-name] command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for example, /24). The mask appears in command outputs in dotted decimal format (A.B.C.D). route-map map- name (OPTIONAL) Enter the keyword route-map then the name of an established route map.
PAGE 407
When a combination of locally originated and peer originated routes occurs, both these routes will exist in the RTM. However, only the best route is kept active in the RTM and the remaining route is rendered inactive. It is possible to keep only one locally originated route in the BGP database. Network command has preference over the re-distributed routes. When the locally originated route is no longer present in the database the other route is automatically installed.
PAGE 408
permit bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to permit incoming or outgoing traffic. Syntax permit bandwidth To disable this setting, enter the no permit bandwidth command. Parameters Defaults bandwidth Enter the keyword bandwidth to specify extended-community attribute as the matching criteria for permitting traffic. The range is from 0 to 102400.
PAGE 409
● set next-hop ● set origin ● set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 410
redistribute ospf Redistribute OSPF routes into BGP. Syntax redistribute ospf process-id [[match external {1 | 2}] [match internal]] [route-map map-name] To stop redistribution of OSPF routes, use the no redistribute ospf process-id command. Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 (OPTIONAL) Enter the keywords match external to redistribute OSPF external | 2} routes. You can specify 1 or 2 to redistribute those routes only.
PAGE 411
router bgp To configure and enable BGP, enter ROUTER BGP mode. Syntax router bgp as-number To disable BGP, use the no router bgp as-number command. Parameters Defaults as-number Enter the AS number. The range is from 1 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). Not enabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 412
Use the no shutdown all command to enable all the configured BGP neighbors. Command Modes ROUTER BGP Command History Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.0 Introduced on the S-Series, Z-Series, MXL, and IOM. You can use this command to disable all the configured BGP neighbors. This command is global for all VRFs. shutdown address-family-ipv4–multicast Disables all the BGP neighbors corresponding to the multicast IPv4 address families.
PAGE 413
shutdown address-family-ipv6–unicast Disables all the BGP neighbors corresponding to the unicast IPv6 address families. Syntax shutdown address-family-ipv6–unicast Use the no shutdown address-family-ipv6–unicast command to enable all the configured BGP neighbors corresponding to the unicast IPv6 address families. Command Modes ROUTER BGP CONFIGURATION Command History Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.
PAGE 414
During configuration, the bandwidth is specified in Mbps, not in bytes/second. While creating the actual LB extended community, the system will attach the AS number and encode the bandwidth in floating point format. show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system.
PAGE 415
Available buffer size 40958758, 27 packet(s) captured using 562 bytes PDU[1] : len 41, captured 00:34:52 ago ffffffff ffffffff ffffffff ffffffff 00290104 000100b4 14141401 0c020a01 04000100 01020080 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:50 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] DellEMC# show config View the current ROUTER BGP configuration.
PAGE 416
show ip bgp View the current BGP IPv4 routing table for the system.
PAGE 417
summary (OPTIONAL) Enter the keyword summary to display the summary of BGP neighbor status. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced the [all {received-routes}] option for IPv4 and IPv6 neighbors on S4810 and S4820T. 9.14(0.
PAGE 418
The show ip bgp command displays the dmzlink-dw details only if dmzlink-bw is enabled using the bgp dmzlink-dw command. Example DellEMC# show ip bgp BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete *> *> Network 55.0.0.
PAGE 419
Origin codes: i - IGP, e - EGP, ? - incomplete *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I Related Commands ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Network 200::/64 200:0:0:1::/64 200:0:0:2::/64 200:0:0:3::/64 200:0:0:4::/64 200:0:0:5::/64 200:0:0:6::/64 200:0:0:7::/64 200:0:0:8::/64 200:0:0:9::/64 200:0:0:a::/64 200:0:0:b::/64 200:0:0:c::/64 200:0:0:d::/64 200:0:0:e::/64 200:0:0:f::/64 200:0:0:10::/64 200:0:0:11::/64 200:0:0:12::/64 200:0:0:13::/64 Next Hop 12::2 12::2 12::2 12
PAGE 420
cluster-id (OPTIONAL) Enter the cluster id in dotted decimal format. The range is 1 — 4294967295. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 421
BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.6 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *>I 55.0.0.0/24 *>I 66.0.0.0/24 *>I 77.0.0.0/24 DellEMC# Next Hop 172.16.0.2 172.16.0.2 172.16.0.
PAGE 422
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 423
Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 66.0.0.0/24 DellEMC# Next Hop 172.16.0.2 Metric LocPrf Weight Path 0 200 i show ip bgp community-list View routes that a specific community list affects.
PAGE 424
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The show ip bgp community-list command without any parameters lists BGP routes matching the Community List and the output is the same as for the show ip bgp command output. The following describes the show ip bgp community-list pass command shown in the following example. Example Field Description Network Displays the destination network prefix of each BGP route.
PAGE 425
ipv4 unicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 426
Example DellEMC# show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network d From 55.0.0.0/24 172.16.0.
PAGE 427
NdIgnrIllId 0 : NdRRC2C 1 : NdClstId 33686273 : NdPaTblP 0x41a19088 NdASPTblP 0x41a19090 : NdCommTblP 0x41a19098 : NhOptTransTblP 0x41a190a0 : NdRRClsTblP 0x41a190a8 NdPktPA 0 : NdLocCBP 0x41a6f000 : NdTmpPAP 0x419efc80 : NdTmpASPAP 0x41a25000 : NdTmpCommP 0x41a25800 NdTmpRRClP 0x41a4b000 : NdTmpOptP 0x41a4b800 : NdTmpNHP : NdOrigPAP 0 NdOrgNHP 0 : NdModPathP 0x419efcc0 : NdModASPAP 0x41a4c000 : NdModCommP 0x41a4c800 NdModOptP 0x41a4d000 : NdModNHP : NdComSortBufP 0x41a19110 : NdComSortHdP 0x41a19d04 : NdUp
PAGE 428
list name Enter the extended community list name you wish to view. The range is 140 characters. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 429
show ip bgp filter-list View the routes that match the filter lists. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] filter-list as-path-name vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
PAGE 430
Field Description ● ● ● ● ● Example i = internal route entry a = aggregate route entry c = external confederation route entry n = network route entry r = redistributed route entry Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight.
PAGE 431
regexp regular- expression Enter a regular expression then use one or a combination of the following characters to match. The range is 256 characters. ● ● ● ● . * + ? = = = = (period) any single character (including a white space). (asterisk) the sequences in a pattern (zero or more sequences). (plus) the sequences in a pattern (one or more sequences). (question mark) sequences in a pattern (either zero or one sequences).
PAGE 432
Example Field Description Reuse Displays the hours:minutes:seconds until the flapped route is available. Path Lists all the ASs the flapping route passed through to reach the destination network. DellEMC# show ip bgp flap-statistics BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 433
Usage Information Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp inconsistent-as command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned.
PAGE 434
show ip bgp neighbors Allows you to view the information BGP neighbors exchange. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] neighbors [ip-address [advertised-routes | dampened-routes | detail | flapstatistics | routes | all {received-routes [network [network-mask]]} | {denied-routes [network [network-mask]]}] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view information exchanged by BGP neighbors corresponding to that VRF.
PAGE 435
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810.
PAGE 436
The Lines Beginning with: Description Received messages This line displays the number of BGP messages received, the number of notifications (error messages), and the number of messages waiting in a queue for processing. Sent messages The line displays the number of BGP messages sent, the number of notifications (error messages), and the number of messages waiting in a queue for processing. Received updates This line displays the number of BGP updates received and sent.
PAGE 437
ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last reset never Local host: 172.16.0.1, Local port: 58145 Foreign host: 172.16.
PAGE 438
Usage Information Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop. Cost Displays the cost associated with using this next hop.
PAGE 439
Usage Information Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF for the S4810, S4820T, and S6000. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 440
show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Syntax show ip bgp [vrf vrf-name] paths community Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 440 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 441
show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]] ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 442
Usage Information The following describes the show ip bgp peer-group command shown in the following example. Line beginning Description with: Example Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported. Minimum time Displays the time interval between BGP advertisements.
PAGE 443
NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular ● ● ● ● ● expression. [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element. { } = (braces) minimum and the maximum match count. ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. $ = (dollar sign) the end of the output string.
PAGE 444
BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 55.0.0.0/24 *> 66.0.0.0/24 DellEMC# Next Hop 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 200 i 0 200 i show ip bgp summary Allows you to view the status of all BGP connections.
PAGE 445
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes. For example, if cluster_id is an attribute associated with thousand routes that contain exactly the same set of attributes, then the cluster_id count is 1.
PAGE 446
Field State/Pfxrcd Description Time Established Display Example < 1 day 00:12:23 (hours:minutes:seconds) < 1 week 1d21h (DaysHours) > 1 week 11w2d (WeeksDays) If the neighbor is in Established stage, the number of network prefixes received. If a maximum limit was configured with the neighbor maximum-prefix command, (prfxd) appears in this column. If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm).
PAGE 447
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. DellEMC# show running-config bgp ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.
PAGE 448
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. timers bgp extended Adjust the BGP idle holdtime for all the BGP neighbors. Syntax timers bgp extended idle-holdtime To return to the default, use the no timers bgp extended command.
PAGE 449
debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 450
Parameters external-distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internal-distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200. local-distance Defaults Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255. The default is 200.
PAGE 451
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.2) Introduced on the S6000, S6000–ON, S6100–ON, and Z9100–ON..
PAGE 452
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized.
PAGE 453
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 454
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Ipv4Acl : 2 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EtsAcl : 0 FcoeAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 ipv4udfmirracl: 0 ipv4mirracl: 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 0 to 8 in multiples of 2. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL.
PAGE 455
Openflow number Enter the keyword openflow and then the number of FP blocks for open flow (multiples of 4). The range is from 0 to 8.The range is from 0 to 9 in multiples of 3. fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The range is from 0 to 6.The range is from 0 to 8 in multiples of 2. Iscsioptacl Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2.The range is from 0 to 9.
PAGE 456
Usage Information Save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings to take effect. The total amount of space allowed is 12 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only 9 number of blocks can be configured by the user . The ipv6acl allocation must be a factor of 3. If allocation values are not entered for the CAM regions, the value is 0.
PAGE 457
Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 458
● When you convert the IPv6 ACL CAM region to double-wide, carve the IPv6 CAM region in multiples of two. You can use a maximum value of eight. ● This feature is supported for IPv6 user ACLs only in the ingress direction. ● After using the feature ipv6acloptimized command on the system, reload the system for the configuration to take effect. Example DellEMC(conf)# feature ipv6acloptimized Configuration change will be in effect after save and reload.
PAGE 459
Example (IPv6 flow-based mirroring information) DellEMC#show cam-acl -- Chassis Cam ACL -Current Settings(in 1 block = 256 Single Wide Regions: Double Wide Regions: : Triple Wide Regions: L2Acl : 0 Ipv4Acl : 2 Ipv6Acl : 3 Ipv4Qos : 0 L2Qos : 0 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl*: 3 ipv4mirracl : 0 block sizes) entries Ipv4Acl L2Acl, L2Qos, L2PT FcoeAcl, ipv4pbr, vrfv4Acl I
PAGE 460
Command Modes EXEC Privilege Command History Usage Information Version Description 9.14(0.0) Updated to display IPv6 flow-based mirroring information on the S5048F-ON, S6100–ON, Z9100–ON, S6000, and S6000–ON. Updated to display the shared region between IPv4 QoS and IPv6 ACL entries on the S5048F–ON, S6100–ON, and Z9100–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.0P1) Optimized the ACL filters to support more than 200 egress ACL rules on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11.0.
PAGE 461
test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax Parameters Defaults test cam-usage service-policy input input policy name stack-unit {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters. number Enter all to get information for all the stack-units or enter the stack-unit number to get information for a specific stack-unit.
PAGE 462
Example Example Term Explanation Estimated CAM per Port Estimates the amount of CAM space the listed policy will require. Status Indicates whether or not the policy will be allowed in the CAM.
PAGE 463
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.. Usage Information This command takes effect only after reboot. Related Commands show hardware forwarding-table mode — displays the hardware forwarding table mode in the current boot and in the next boot.
PAGE 464
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 465
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. cpu-protocol-group Creates or removes a protocol group. Syntax cpu-protocol-group group-name Use the no cpu-protocol-group group-name command to remove the protocol-group. Command Modes CONFIGURATION Parameters Command History Example group-name Enter the unique protocol-group name that you want to create.
PAGE 466
cpu-queue Configures queue parameters. Syntax cpu-queue queue-number {protocol-group group-name [qos-policy policy-name] | qos-policy policy-name} Use the no cpu-queue queue-number command to remove the queue parameter configuration. Command Modes COPP-PROFILE Parameters queue-number Enter the queue number that you want to configure. The range is from 0 to 11. A queue can be mapped to a protocol-group or a qos-policy or both. Protocol groups cannot be configured for queue numbers 0 and 4.
PAGE 467
Usage Information Following are the prerequisite for applying a CoPP policy: ● Ensure that the protocols are not running. If protocols are running, issues such as, packets arriving out of order, may occur. ● Ensure that the service-class cpu-queue-buffer command is not configured. The copppolicy command will not be available if the service-class cpu-queue-buffer command is configured.
PAGE 468
queue-length Configures queue length. Syntax queue—length queue-length-value Use the no queue-length command to remove the queue length configuration. Command Modes QOS-POLICY-INPUT Parameters Default Command History Usage Information Example queue-lengthvalue Enter the queue length value you want to configure. The range is from 0 to 235. The default value is 235. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.0 Introduced on the S6000, S6000–ON, Z9100–ON, and S6100–ON.
PAGE 469
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Create a policy-map by associating a queue number with the qos-policy. Create QoS policies prior to enabling this command. For CoPP, use the keyword cpu-qos when creating qos-policy-input.
PAGE 470
For CoPP, use the keyword cpu-qos when creating qos-policy-input. Related Commands ● ● ● ● ● ip access-list extended — creates an extended IP ACL. mac access-list extended — creates an extended MAC ACL. qos-policy-input — creates a QoS input policy map. class-map — creates a QoS class map. policy-map-input — creates an input policy map. show cpu-queue rate cp Display the rates for each CPU queue. Syntax show cpu-queue rate cp Defaults Not configured.
PAGE 471
Q9 Q10 Q11 DellEMC# 600 600 300 50 50 50 show ip protocol-queue-mapping Display the queue mapping for each configured protocol. Syntax show ip protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Modified the output to display MCAST data packet information. 9.12(1.
PAGE 472
show ipv6 protocol-queue-mapping Display the queue mapping for each configured IPv6 protocol. Syntax show ipv6 protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Modified the output to display MCAST data packet information. 9.12(1.0) Introduced on the S5048F–ON. 9.
PAGE 473
TCP (BGP) UDP (DHCPV6) ICMPV6 NA ICMPV6 RA ICMPV6 NS ICMPV6 RS ICMPV6 VRRPV6 OSPFV3 DellEMC# any/179 546/547 any any any any any any any 179/any 546/547 any any any any any any any _ _ _ _ _ _ _ _ _ Q9 Q10 Q6 Q6 Q5 Q5 Q6 Q10 Q9 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ show mac protocol-queue-mapping Display the queue mapping for the MAC protocols. Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 474
show running-config copp-profile Displays the configured CoPP profiles. Syntax show running-config copp-profile Defaults none Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.0 Introduced on the S6000, S6000–ON, Z9100–ON, and S6100–ON.
PAGE 475
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 476
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 477
show hardware pfc-nodrop-priority — displays the packets drop count corresponding to the priority. clear pfc counters Clear the PFC TLV counters and PFC statistics on an interface or stack unit. Syntax Parameters clear pfc counters [interface interface-type | stack-unit {unit-number | all} stack-ports all] interface interface-type Enter the keywords port-type then the interface information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 478
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.0) Introduced on the Z9100-ON and S6100-ON. Example pfc-nodrop-priority l2-dlf drop Configure to drop the unknown unicast packets flooding on lossless priorities.
PAGE 479
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. ● When you configure lossless queues on an interface, PFC priority configuration is not allowed on the dcb-map profile applied on the interface.
PAGE 480
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. The default number of 802.1p priorities that you can enable for PFC is 2. The maximum number of 802.1p priorities that you can enable for PFC is –4. Queues to which PFC priority traffic is mapped are lossless by default.
PAGE 481
for guaranteed services like global headroom, queue's min guaranteed buffer and CPU queues. PFC Total Buffer: Maximum buffer available for lossless queues. PFC Shared Buffer: Buffer used by ingress priority groups for shared usage. PFC Headroom Buffer: Buffer used by ingress priority group for shared headroom usage. PFC Available Buffer: Current buffer available for new lossless queues to be Provisioned.
PAGE 482
{summary | statistics | detail | bufferthreshold} Enter the keyword summary for a summary list of results or enter the keyword detail for a full list of results. Enter the keyword statistics to view pfc statistics. Use the keyword buffer-threshold to display the buffer threshold details. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 483
Field Description Local is enabled DCBX operational status (enabled or disabled) with a list of the configured PFC priorities. Operational status (local port) Port state for current operational PFC configuration: ● Init: Local PFC configuration parameters were exchanged with the peer. ● Recommend: Remote PFC configuration parameters were received from the peer. ● Internally propagated: PFC configuration parameters were received from the configuration source.
PAGE 484
Example (Summary) Field Description PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
PAGE 485
PFC Link Delay 65535 pause quntams Application Priority TLV Parameters : -------------------------------------FCOE TLV Tx Status is disabled ISCSI TLV Tx Status is disabled Local FCOE PriorityMap is 0x0 Local ISCSI PriorityMap is 0x0 1 Input TLV pkts, 4 Output TLV pkts, 0 Error pkts, 0 Pause Tx pkts, 0 Pause Rx pkts 0 Input Appln Priority TLV pkts, 0 Output Appln Priority TLV pkts, 0 Error Appln Priority TLV Pkts DellEMC(conf-lldp)#do show int hundredGigE 1/49 pfc summary Interface hundredGigE 1/49 Admin mo
PAGE 486
Usage Information Example (Summary) Version Description 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 487
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 488
show interface ets Displays the ETS configuration applied to egress traffic on an interface, including priority groups with priorities and bandwidth allocation. Syntax show interface port-type slot/port[/subport] ets {summary | detail} Parameters port-type slot/ port[/subport] ets Enter the port-type slot and port ETS information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 489
0 1 2 3 4 5 6 7 0,1,2,3,4,5,6,7 100 - - - - - ETS - Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rate(Mbps) Burst(KB) ---------------------------------------------------------------------------------0 0,1,2,3,4,5,6,7 100 ETS 1 2 3 4 5 6 7 Oper status is init ETS DCBX Oper status is Down Reason: Port Shutdown State Machine Type is Feature Conf TLV Tx Status is enable
PAGE 490
DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS. advertise dcbx-tlv On a DCBX port with a manual role, configure the PFC and ETS TLVs advertised to DCBX peers. Syntax advertise dcbx-tlv {ets-conf | ets-reco | pfc} [ets-conf | ets-reco | pfc] [ets-conf | ets-reco | pfc] To remove the advertised ETS TLVs, use the no advertise dcbx-tlv command.
PAGE 491
To remove DCBX port role, use the no dcbx port-role {config-source | auto-downstream | auto-upstream | manual} command. Parameters Defaults config-source | Enter the DCBX port role, where: auto-downstream ● config-source: configures the port to serve as the configuration source on | auto-upstream | the switch. manual ● auto-upstream: configures the port to receive a peer configuration. The configuration source is elected from auto-upstream ports.
PAGE 492
● cin: configures the port to use Cisco-Intel-Nuova (DCBX 1.0). NOTE: For CIN, priority-group/traffic-class group wise bandwidth works and priority wise bandwidth configuration is ignored. ● ieee-v2: configures the port to use IEEE 802.1az (Draft 2.5). Defaults Auto Command Modes INTERFACE PROTOCOL LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 493
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 494
Parameters port-type Enter the port type along with the port number. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 495
Field Description Local DCBX DCBX version configured on the port: CEE,| cin , IEEE v2.5, or Auto (port autoConfigured mode configures to use the DCBX version received from a peer). Peer Operating version DCBX version that the peer uses to exchange DCB parameters. Local DCBX TLVs Transmission status (enabled or disabled) of advertised DCB TLVs (see TLV code Transmitted at the top of the show command output). Local DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs.
PAGE 496
e-ETS Configuration TLV disabled R-ETS Recommendation TLV enabled r-ETS Recommendation TLV disabled P-PFC Configuration TLV enabled p-PFC Configuration TLV disabled F-Application priority for FCOE enabled f-Application Priority for FCOE disabled ----------------------------------------------------------Interface twentyFiveGigE 1/9 Remote Mac Address 00:00:00:00:00:11 Port Role is Auto-Upstream DCBX Operational Status is Enabled Is Configuration Source? TRUE Local DCBX Compatibility mode is CEE Local DCBX Co
PAGE 497
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.3(0.0) Introduced on the S4810 and S6000 platforms. A DCB map is a template used to configure DCB parameters and apply them on converged Ethernet interfaces. DCB parameters include priority-based flow control (PFC) and enhanced traffic selection (ETS). To display the PFC and ETS settings in DCB maps, enter the show qos dcb-map name command.
PAGE 498
● Priority group 0 contains traffic with dot1p priorities 0, 1, and 2. ● Priority group 1 contains traffic with dot1p priority 3. ● Priority group 2 contains traffic with dot1p priority 4. ● Priority group 4 contains traffic with dot1p priority 5, 6, and 7. To remove a priority-pgid configuration from a DCB map, enter the no priority-pgid command. For PFC enabled priorities, it is recommended to map single priority per Priority group.
PAGE 499
Repeat the priority-group bandwidth pfc command to configure PFC and ETS traffic handling for each priority group in a DCB map. You can enable PFC on a maximum of two priority queues. If you configure more than one priority group as strict priority, the higher numbered priority queue is given preference when scheduling data traffic. If a priority group does not use its allocated bandwidth, the unused bandwidth is made available to other priority groups.
PAGE 500
dcb-buffer-threshold Configure the profile name for the DCB buffer threshold. Syntax dcb buffer—threshold profile-name Parameters Default profile-name Enter the name of the profile, which can be a string of up to 32 characters in length. None Command Modes CONFIGURATION mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON.
PAGE 501
buffer-size Ingress buffer size. size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 9 KB.Enter a number in the range of 0 to 9. The default is as follows: ● ● ● ● ● 10G – 9 25G – 9 40G – 9 50G – 9 100G – 9 pause-threshold Buffer limit for pause frames to be sent. NOTE: In addition to the specified pause-threshold value, pause frames are sent only when the buffer usage exceeds some percentage of the shared buffer.
PAGE 502
Usage Information For each priority, you can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets. When PFC detects congestion on a queue for a specified priority, it sends a pause frame for the 802.1p priority traffic to the transmitting device. You can use the priority command to set up both the administrative and peer-related PFC priorities.
PAGE 503
dcb pfc-total-buffer-size Configure the total buffer size for PFC in kilobytes. Syntax Parameters Default dcb pfc-total—buffer—size buffer-size buffer-size Enter a number in the range of 0 to 4727. The default is 2656KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.
PAGE 504
in the system DellEMC(conf)# show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration. Syntax show running—config dcb-buffer-threshold Command Modes EXEC EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 505
dcb-buffer-threshold test2 pfc priority 0 buffer-size 80 pause-threshold 50 ! dcb-buffer-threshold test3 pfc priority 0 buffer-size 80 pause-threshold 60 resume-threshold 30 DellEMC#show interfaces twentyFiveGigE 1/1 pfc buffer-threshold Interface twentyFiveGigE 1/1 Interface Queue# Lossless Buffer-size Pause-threshold Peak-headroom Resume-offset Shared Threshold (KB) (KB) (KB) (KB) Weight -----------------------------------------------------------------------------------------------------------Tf 1/1 Q0 N
PAGE 506
● To disable ETS on interface, use “no dcb ets enable” command. ● To disable PFC on interface, use “no dcb pfc enable” command. Defaults Enable Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100. 9.8(1.
PAGE 507
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 508
Usage Information The Kernel core dump can be large and may take up to 5 to 30 minutes to upload. Dell EMC Networking OS does not overwrite application core dumps so you should delete them as necessary to conserve space on the flash; if the flash is out of memory, the coredump is aborted. On the S-Series, if the FTP server is not reachable, the application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system.
PAGE 509
interactive Defaults Enter the keyword interactive with the test ID to test interactive test cases. The test cases can be found using the show diag testcase stack-unit stack-unit-id interactive command. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 510
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit.
PAGE 511
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented.
PAGE 512
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CPUTYPEDETECTTEST CPUSDRAMPRESENCETEST CPUSDRAMSIZETEST CPLDBOARDTYPETEST I2CACCESSTEST PSUPRESENCETEST PSUSOURCETYPETEST PSUSTATUSMONITORTEST PSUFANSPEEDMONITORTEST PSUFANSTATUSMONITORTEST PSUFANAIRFLOWTYPETEST FANTRAYPRESENCETEST FANSTATUSMONITORTEST FANAIRFLOWTYPETEST RTCPRESENCETEST SSDPRESENCETEST Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 Level0 [output truncated] Command History This guide is pl
PAGE 513
Defaults cpu party-bus statistics Enter the keywords cpu party-bus statistics to clear the management statistics. cpu satainterface statistics Enter the keywords cpu sata-interface statistics to clear the sata interface statistics. stack-port Enter the keywords stack-port then the port number of the stacking port to clear the statistics of the particular stacking port. None Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific.
PAGE 514
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 515
hardware watchdog To trigger a reboot and restart the system, set the watchdog timer. Syntax hardware watchdog stack-unit {stack-unit-number | all} Defaults Enabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 516
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 517
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. show hardware ipv6 Display Layer 3 IPv6 ACL data for the selected stack member and stack member port-pipe.
PAGE 518
show hardware stack-unit Display the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 519
Example (DataPlane) Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Replaced the keyword port with interface. 9.7(0.
PAGE 520
0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec Output 00.
PAGE 521
0 0 0 0 DellEMC# 0 0 0 0 DellEMC# sh hard stack-unit 1 drops unit 0 PortNumber Ingress Drops IngMac Drops Total Mmu Drops 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 EgMac Drops Egress Drops 0 0 0 0 0 0 0 0 DellEMC# DellEMC#show hardware stack-unit 1 drops unit 0 UserPort PortNumber 1/1 1 1/2 2 1/3 3 1/4 4 1/5 5 1/6 6 1/7 7 1/8 8 Ing-MMU-Drops HOL-MMU-Drops 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EgressDrops 0 0 0 0 0 0 0 0 [output truncated] Example (PortStats) 0 0 0 0 0 0 0 0 IngressDrops Aged-MMU-Drops 0 0 0 0 0 0 0 0
PAGE 522
hg0 up 12G FD hg1 up 12G FD hg2 down 10G FD hg3 down 10G FD 0 DellEMC# SW SW SW SW No No No No Forward Forward Forward Forward None None None None F F F F XGMII XGMII XGMII XGMII 16360 16360 16360 16360 DellEMC# show hardware stack-unit 1 unit 0 port-stats ena/ speed/ link auto STP lrn inter max loop port link duplex scan neg? state pause discrd ops face frame back ge0 down SW Yes Block Untag FA SGMII 1554 ge1 !ena SW Yes Block Tag FA SGMII 1554 ge2 !ena SW Yes Block Tag FA SGMII 1554 ge3 !ena SW Ye
PAGE 523
0x0060104c 0x0060204c 0x0060304c 0x0060404c 0x0060504c 0x0060604c 0x0060704c 0x0060804c 0x0060904c 0x0060a04c 0x0060b04c 0x0060c04c 0x0060d04c 0x0060e04c 0x0060f04c 0x0061004c 0x0061104c 0x0061204c 0x0061304c 0x0061404c 0x0061504c 0x0061604c 0x0061704c 0x0061804c 0x0061904c 0x0061a04c 0x0061b04c 0x0061c04c 0x00780000 0x0e700102 0x0e701102 0x0e702102 0x0e703102 0x0e704102 0x0e705102 0x0e706102 0x0e707102 0x0e708102 0x0e709102 0x0e70a102 0x0e70b102 0x0e70c102 0x0e70d102 0x0e70e102 0x0e70f102 0x0e710102 0x0e71
PAGE 524
0x0b70a001 BCAST_STORM_CONTROL.ge10 = 0x00000000 !------------------ output truncated ---------------! DellEMC# show hardware stack-unit 1 unit 1 register 0x0068003c AGINGCTRMEMDEBUG.mmu0 = 0x00000000 0x0068003d AGINGEXPMEMDEBUG.mmu0 = 0x00000000 0x00680017 ASFCONFIG.mmu0 = 0x0000000e 0x0060004c ASFPORTSPEED.ge0 = 0x00000000 0x0060104c ASFPORTSPEED.ge1 = 0x00000000 0x0060204c ASFPORTSPEED.ge2 = 0x00000000 0x0060304c ASFPORTSPEED.ge3 = 0x00000000 0x0060404c ASFPORTSPEED.
PAGE 525
0x0b705001 BCAST_STORM_CONTROL.ge5 = 0x00000000 0x0b706001 BCAST_STORM_CONTROL.ge6 = 0x00000000 0x0b707001 BCAST_STORM_CONTROL.ge7 = 0x00000000 0x0b708001 BCAST_STORM_CONTROL.ge8 = 0x00000000 0x0b709001 BCAST_STORM_CONTROL.ge9 = 0x00000000 0x0b70a001 BCAST_STORM_CONTROL.ge10 = 0x00000000 !------------------ output truncated ---------------! DellEMC# show hardware stack-unit 1 unit 0 register 0x38804000 ASF_CREDIT_THRESH_HI.xe113 = 0x00000007 0x38804010 ASF_CREDIT_THRESH_HI.
PAGE 526
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame Priority 2 PFC Frame Priority 3 PFC Frame Priority 4 PFC Frame Priority 5 PFC Frame Priority 6 PFC Frame Priority 7 Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter
PAGE 527
The CPU Port of the device is 28 The number of ports in device 1 is - 24 The number of Hg ports in devices 1 is - 4 The CPU Port of the device is 28 The staring unit no the SWF in the device is 0 ****************************************************** The Current Link Status Is Front End Link Status 0x000000000000400000000000 Front End Port Present Status 0x000000000000000000000000 Back Plane Link Status 0x00000000 ****************************************************** Link Status of all the ports in the Dev
PAGE 528
The linkStatus of Front End Port 0 is FALSE The linkStatus of Front End Port 1 is FALSE The linkStatus of Front End Port 2 is FALSE The linkStatus of Front End Port 3 is FALSE The linkStatus of Front End Port 4 is FALSE The linkStatus of Front End Port 5 is FALSE The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus of Front End Port 9 is FALSE The linkStatus of Front End Port 10 is FALSE The linkStatus of Front End
PAGE 529
Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Tf 1/3 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Tf 1/4 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Tf 1/5 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer
PAGE 530
Enter the keyword priority-group followed by id for specific priority group or keyword all. buffer-info To display total buffer information for the port interface, enter the keywords buffer-info. To display a queue range, enter 0 to 19 for a specific queue or all.
PAGE 531
----------------------------------------------------------------HP1 0 0 DellEMC# show hardware buffer headroom-pool Display the headroom pool buffer usage. Syntax Parameters show hardware buffer {headroom-pool {buffer-info | detail buffer-info}} headroom-pool buffer-info Enter the keyword headroom-pool followed by the keyword buffer-info for information on the headroom pool buffer usage.
PAGE 532
----------------------------------------------------------------Service-Pool Configured Buffer(KB) Used Buffer(KB) ----------------------------------------------------------------SP0(Lossy) 9758 7760 SP1(Lossless) 3842 697 DellEMC# DellEMC#show hardware buffer service-pool detail buffer-info ------Buffer Details for Stack-Unit 1 portpipe 0 ----------Buffer Details for MMU 0--------------------------------------------------------------------Service-Pool Configured Buffer(KB) Used Buffer(KB) -----------------
PAGE 533
queue Enter the keyword queue followed by all for displaying details of all queues, ucast queue-id or all for displaying Unicast queue details, and mcast queue-id or all for displaying Multicast queue details. priority-group Enter the keyword priority-group followed by id for specific priority-group or keyword all.
PAGE 534
unicast packets for the specific interface Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface hundredGigE 1/49 queue ucast all Stack-unit 1 unit: 0 port: 34 (interface Hu 1/49) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 Example displaying egress queue-
PAGE 535
6 7 Example showing buffer snap shot details for head room pool 0 0 0 0 DellEMC#show hardware buffer-stats-snapshot resource headroom-pool --------------------------------------HP# PEAK USE COUNT(CELLS) --------------------------------------0 0 1 0 2 0 3 0 DellEMC# DellEMC#show hardware buffer-stats-snapshot resource headroom-pool detail -----------------------------------------------HP# MMU# PEAK USE COUNT(CELLS) -----------------------------------------------0 0 0 0 1 0 0 2 0 0 3 0 1 0 0 1 1 0 1 2 0 1
PAGE 536
Version Description 9.14(0.0) Included the FEC BER details in the output for 25 and 50GG interfaces of the S5048–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Included the FEC BER details in the output for 100G interfaces of S6100–ON and Z9100–ON . Included FCS Error Ratio in the output for all interfaces of S6000, S6000–ON, S6100–ON, and Z9100–ON. Example displaying internal drops 536 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 537
HOL DROPS on COS5 : 0 HOL DROPS on COS6 : 0 HOL DROPS on COS7 : 0 HOL DROPS on COS8 : 0 HOL DROPS on COS9 : 0 HOL DROPS on COS10 : 3240829783 HOL DROPS on COS11 : 0 HOL DROPS on COS12 : 0 HOL DROPS on COS13 : 0 HOL DROPS on COS14 : 0 HOL DROPS on COS15 : 0 HOL DROPS on COS16 : 0 HOL DROPS on COS17 : 0 HOL DROPS on COS18 : 0 HOL DROPS on COS19 : 0 TxPurge CellErr : 0 Aged Drops : 0 --- Egress MAC counters--Egress FCS Drops : 0 --- Egress FORWARD PROCESSOR Drops --IPv4 L3UC Aged & Drops : 0 TTL Threshold Drop
PAGE 538
HOL DROPS on COS14 : 0 HOL DROPS on COS15 : 0 HOL DROPS on COS16 : 0 HOL DROPS on COS17 : 0 HOL DROPS on COS18 : 0 HOL DROPS on COS19 : 0 TxPurge CellErr : 0 Aged Drops : 0 --- Egress MAC counters--Egress FCS Drops : 0 --- Egress FORWARD PROCESSOR Drops --IPv4 L3UC Aged & Drops : 0 TTL Threshold Drops : 0 INVALID VLAN CNTR Drops : 0 L2MC Drops : 0 PKT Drops of ANY Conditions : 0 Hg MacUnderflow : 0 TX Err PKT Counter : 0 --- Error counters--Internal Mac Transmit Errors : 0 Unknown Opcodes : 0 Internal Mac R
PAGE 539
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500.
PAGE 540
show hardware system-flow Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe. Syntax show hardware system-flow stack-unit id port-set number [counters | pipeline pipeline-number] Parameters stack-unit id Enter the keywords stack-unit to select a stack member ID. port-set number Enter the keywords port-set with a port-pipe number. [counters | pipeline pipeline- (OPTIONAL) Enter the keyword counters for the specified port-pipe.
PAGE 541
382 VRRP Packets 0 380 BCast L2_DST_HIT on VLAN 4095 0 379 BCAST L2_DST_HIT Packets 0 4 Unknown L2MC Packets 0 3 L2DLF Packets 0 2 L2UCAST Packets 0 1 L2BCASTPackets 0 25 DellEMC# DellEMC# show hardware system-flow stack-unit 1 port-set 0 counters ----------------------------------------------------------EntryId Description #HITS ----------------------------------------------------------2048 STP BPDU Redirects 0 2047 LLDP BPDU Redirects 0 2045 LACP traffic Redirects 0 2044 GVRP traffic Redirects 0 2043 ARP
PAGE 542
action={act=Drop, param0=0(0x00), param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=2, mode=0x01, entries=1} ################# FP Entry for redirecting GVRP traffic to RSM ########### EID 2044: gid=1, slice=15, slice_idx=0x03, prio=0x7fc, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 0180c200
PAGE 543
action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=3, mode=0x01, entries=1} ################# FP Entry for redirecting ARP Replies to RSM ############# EID 2043: gid=1, slice=15, slice_idx=0x04, prio=0x7fb, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 00000000 00000000 00000806 00001600 , FPF4=0x00 MASK=0x0000
PAGE 544
Example Related Commands 544 Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command.
PAGE 545
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 546
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table.
PAGE 547
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 548
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command.
PAGE 549
dns-server Assign a DNS server to clients based on address pool. Syntax Parameters Defaults dns-server address [address2...address8] address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 550
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 551
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. hardware-address For manual configurations, specify the client hardware address. Syntax Parameters Defaults hardware-address address address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific.
PAGE 552
Command Modes DHCP-POOL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14.1.3 This command replaces host command. Introduced on S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, S6000, S4810, S4820T, S5048F-ON, MXL, FN-IOM, and C9010. When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.
PAGE 553
lease Specify a lease time for the addresses in a pool. Syntax Parameters Defaults lease {days [hours] [minutes] | infinite} days Enter the number of days of the lease. The range is from 0 to 31. hours Enter the number of hours of the lease. The range is from 0 to 23. minutes Enter the number of minutes of the lease. The range is from 0 to 59. infinite Specify that the lease never expires. 24 hours Command Modes DHCP Command History This guide is platform-specific.
PAGE 554
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 555
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. network Specify the range of addresses in an address pool.
PAGE 556
pool Create an address pool. Syntax pool name Parameters Defaults name Enter the address pool’s identifying name. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 557
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 558
Example Version Description 8.2.1.0 Introduced on the C-Series and S-Series. DellEMC# show ip dhcp configuration global Protocol status : Enabled Number of ping packets : 1 DellEMC# DellEMC# show ip dhcp configuration Pool Name Pool Type Domain Name Lease Time DNS Servers Default Routers Network : : : : : : : pool p1 p1 Dynamic dell.com 2Days 0Hrs 0Mins 10.11.0.1 1.1.1.1 1.1.1.0 255.255.255.0 show ip dhcp conflict Display the address conflict log.
PAGE 559
show ip dhcp server Display the DHCP server statistics. Syntax show ip dhcp server statistics Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 560
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 561
Command Modes ● INTERFACE ● INTERFACE PORT-CHANNEL Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 562
● For a port channel interface, enter the keywords port-channel then a number. Defaults None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 563
clear ipv6 dhcp snooping binding Clear all the DHCPv6 snooping binding database entries. Syntax clear ipv6 dhcp snooping binding Defaults None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 564
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 565
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series on Layer 2 interfaces. 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces. When enabled, no learning takes place until you enable snooping on a VLAN. After disabling DHCP snooping, the binding table deletes and Option 82, IP Source Guard, and Dynamic ARP Inspection are disabled.
PAGE 566
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 567
Version Description 9.14(1.0) Enhanced the command to map multiple IP addresses to one MAC address on the S4810 and S4820T. 9.13(0.0) Enhanced the command to map multiple IP addresses to one MAC address on the S5048F–ON. 9.13(0.0) Enhanced the command to map multiple IP addresses to one MAC address. Enhanced to support DHCP snooping in a VLT setup. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 568
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 569
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.
PAGE 570
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 571
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 572
To disable dhcp snooping trusted capability on this interface, use the no ipv6 dhcp snooping trust command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 573
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Added the keyword ipmac. 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2.
PAGE 574
Example Version Description 9.11(2.0P0) Introduced the circuit-id attribute in the command. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 575
Command Modes ● CONFIGURATION ● INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface.
PAGE 576
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 577
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
PAGE 578
Parameters Default vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF through which the host address can be reached. ipv6-address Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.
PAGE 579
Parameters Description ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 580
permit vlan 20 host 10.2.2.1 host 00:00:00:aa:00:03 permit vlan 20 host 10.2.2.2 host 00:00:00:aa:00:04 count (0 packets) count (0 packets) The following example displays the port channel interfaces configured with IP Source Guard: DellEMC> show ip dhcp snooping source-address-validation interface portchannel 10 ipmac-vlan sav access-list on Port-channel 10 on stack-unit 1 Total cam count 5 permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 1.1.1.
PAGE 581
show ipv6 dhcp snooping Display the DHCPv6 snooping binding database. Syntax show ipv6 dhcp snooping Defaults None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 582
ip-address [ ipaddress2 ] [ ipaddress3 ] [ ipaddress4 ] [ ipaddress5 ] [ ipaddress6 ] Defaults Enter the IP address of the name server in dotted decimal format. NOTE: Use the additional ip-address parameters (ip-address2 to ipaddress6) in a sequential order to specify up to a maximum of six IP addresses per VRF. None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 583
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to configure a domain name corresponding to a VRF.
PAGE 584
Usage Information Example Version Description 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to add domain names to the DNS lists corresponding to a specific VRF. You can add up to a maximum of six domain names to the DNS list corresponding to a VRF. This domain is used to complete the unqualified host names. DellEMC(conf)# ip domain-list DellEMC(conf)# ip domain-list vrf jay dell.com vrf jay force10.
PAGE 585
clear host Removes one or all dynamically learned host table entries for a specific VRF. Syntax Parameters Defaults clear host [vrf vrf-name] {* | host-name} vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to delete dynamically learned host table entries corresponding to that VRF. host-name Enter the name of the host corresponding to which you want to delete the dynamically learnt host table entries. * Enter * to delete all host table entries.
PAGE 586
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • ecmp-group hash-algorithm ip ecmp-group ip ecmp weighted link-bundle-distribution trigger-threshold link-bundle-monitor enable ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold.
PAGE 587
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810.
PAGE 588
● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR hg { crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16 } stackunit stack-unitnumber | portset port-pipe Enter the keyword hg then one of the following options: ● ● ● ● ● ● ● ● ● crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial crc32MSB: Use CRC32_UPPER — MSB 16 bits of compute
PAGE 589
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Added the nh-ecmp option. 7.7.1.
PAGE 590
ip ecmp-group Enable and specify the maximum number of ecmp that the L3 CAM hold for a route, By default, when maximum paths are not configured, the CAM can hold a maximum of 16 ecmp per route. Syntax ip ecmp-group {maximum-paths | {number} {path-fallback} To negate a command, use the no ip ecmp-group maximum-paths {number} command. Parameters Defaults maximum-paths Specify the maximum number of ECMP for a route. The range is 2 to 64.
PAGE 591
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series.
PAGE 592
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. link-bundle-monitor enable Provides a mechanism to enable monitoring of traffic distribution on an ECMP link bundle.
PAGE 593
16 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash enhancements. Topics: • • • • load-balance ingress-port enable load-balance flexhash lacp fast-switchover encapsulation dot1q load-balance ingress-port enable Enable the Flex hash functionality. This utility is supported on the platform. Syntax load-balance ingress-port enable To disable the Flex hash capability, use the no version of this command.
PAGE 594
load-balance flexhash Specify the parameters for the Flex Hash mechanism, such as whether IPv4 or IPv6 packets must be subject to Flex Hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name.
PAGE 595
Example DellEMC(conf)# load-balance flexhash ipv4 ip-proto 1 desc offset1 1 offset2 2 lacp fast-switchover Cause the physical ports to be aggregated faster by configuring this capability in a port-channel on both the nodes that are members of a port-channel. Syntax lacp fast-switchover To disable the capability of faster aggregation of the member ports of a LAG or a port-channel bundle, use the no version of this command.
PAGE 596
Usage Information 596 Version Description 9.3.0.0 Introduced on the S6000. 9.2(1.0) Introduced on the Z9500. To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction.
PAGE 597
17 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE enddevice and an FCF.
PAGE 598
Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface.
PAGE 599
info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 600
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 601
Usage Information Before enabling FIP snooping, assign the fcoeacl space using the cam-acl command. If not assigned, the following error message is displayed: DellEMC(conf)#feature fip-snooping % Error: Cannot enable fip snooping. CAM Region not allocated for Fcoe. DellEMC(conf)#cam-acl l2acl 2 ipv4acl 0 ipv6acl 0 ipv4qos 2 l2qos 0 l2pt 0 ipmacacl 0 vman-qos 0 fcoeacl 2 etsacl 1 iscsi 2 DellEMC(conf)#feature fip-snooping fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN.
PAGE 602
Defaults 0x0EFC00 Command Modes ● CONFIGURATION ● VLAN INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.
PAGE 603
fip-snooping port-mode fcf Configure the port for bridge-to-FCF links. Syntax fip-snooping port-mode fcf To disable the bridge-to-FCF link on a port, use the no fip-snooping port-mode fcf command. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 604
Example DellEMC# show fip-snooping config FIP Snooping Feature enabled Status: Enabled FIP Snooping Global enabled Status: Enabled Global FC-MAP Value: 0X0EFC00 FIP Snooping enabled VLANs VLAN Enabled FC-MAP ----------------100 TRUE 0X0EFC00 show fip-snooping enode Display information on the ENodes in FIP-snooped sessions, including the ENode interface and MAC address, FCF MAC address, VLAN ID and FC-ID.
PAGE 605
show fip-snooping fcf Display information on the FCFs in FIP-snooped sessions, including the FCF interface and MAC address, FCF interface, VLAN ID, FC-MAP value, FKA advertisement period, and number of ENodes connected. Syntax Parameters show fip-snooping fcf [fcf-mac-address] fcf-mac-address Enter the MAC address of the FCF to display. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 606
show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax show fip-snooping statistics [interface vlan vlan-id | interface interfacetype | interface port-channel port-channel-number] Parameters vlan-id Enter the VLAN ID of the FIP packet statistics displays. port-channelnumber Enter the port channel number of the FIP packet statistics displays.
PAGE 607
Field Description Number of VN Port Keep Alives Number of FIP-snoop VN port (Virtual N-port) keep-alive frames received on the interface Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snoop unicast discovery advertisements received on the interface. Number of FLOGI Number of FIP FLOGI accept frames received on the interface.
PAGE 608
Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int twentyFiveGigE 1/11 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of FLOGI :1 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :4416 Number of VN Port Keep Alive :3136 Number of Multicast Discovery Advertisement :0 Number of Unicast Discovery Advertisement :0 Number of FLOGI Accepts
PAGE 609
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 610
18 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
PAGE 611
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 612
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 613
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 614
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 615
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 616
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced.
PAGE 617
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. protocol frrp Enter the Resilient Ring Protocol and designate a ring identification. Syntax protocol frrp {ring-id} To exit the ring protocol, use the no protocol frrp {ring-id} command. Parameters Defaults ring-id Enter the ring identification number. The range is from 1 to 255.
PAGE 618
show frrp Display the resilient ring protocol configuration. Syntax show frrp [ring-id [summary]] | [summary] Parameters Defaults ring-id Enter the ring identification number. The range is from 1 to 255 summary (OPTIONAL) Enter the keyword summary to view just a summarized version of the Ring configuration. None Command Modes EXEC Command History Usage Information This guide is platform-specific.
PAGE 619
Example (Summary) DellEMC# show frrp summary Ring-ID State Mode Ctrl_Vlan Member_Vlans ---------------------------------------------2 UP Master 2 11-20, 25,27-30 31 UP Transit 31 40-41 50 Down Transit 50 32 DellEMC# Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 620
Example (1) Example (1) Example (2 Summary) DellEMC# show frrp 1 Ring protocol 1 is in Master mode Ring Protocol Interface: Primary : twentyFiveGigE 1/16 State: Forwarding Secondary: Port-channel 100 State: Blocking Control Vlan: 1 Ring protocol Timers: Hello-Interval 50 msec Dead-Interval 150 msec Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348 Number of state Changes: 34 Member Vlans: 1000-1009 DellEMC# DellEMC# show frrp 1 Rin
PAGE 621
Defaults ● 500 ms for hello-interval milliseconds ● 1500 ms for dead-intervalmilliseconds Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 622
19 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 623
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax Parameters clear gvrp statistics interface interface interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 624
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 625
disable Globally disable GVRP. Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 626
leave Enter the keyword leave then the number of milliseconds to configure the leave time. The range is from 100 to 2147483647 milliseconds. The default is 600 milliseconds. NOTE: Designate the milliseconds in multiples of 100. leave-all Enter the keywords leave-all then the number of milliseconds to configure the leave-all time. The range is from 100 to 2147483647 milliseconds. The default is 1000 milliseconds. NOTE: Designate the milliseconds in multiples of 100. Defaults As above.
PAGE 627
gvrp enable Enable GVRP on physical interfaces and LAGs. Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 628
Defaults normal Command Modes CONFIGURATION-INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 629
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 630
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series ● gvrp enable — enable GVRP on physical interfaces and LAGs. ● protocol gvrp — access the GVRP protocol. show garp timers Display the GARP timer settings for sending GARP messages. Syntax show garp timers Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands 630 This guide is platform-specific.
PAGE 631
show gvrp Display the GVRP configuration. Syntax Parameters show gvrp [brief | interface] brief (OPTIONAL) Enter the keyword brief to display a brief summary of the GVRP configuration. interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information.
PAGE 632
Example Related Commands DellEMC# show gvrp brief GVRP Feature is currently enabled. Port GVRP Status Edge-Port ---------------------------------------------Tf 1/1 Disabled No Tf 1/2 Enabled No Tf 1/3 Disabled No Tf 1/4 Disabled No Tf 1/5 Disabled No Tf 1/6 Disabled No Tf 1/7 Disabled No Tf 1/8 Disabled No DellEMC# show gvrp brief ● show gvrp statistics — display the GVRP statistics. show gvrp statistics Display the GVRP configuration statistics.
PAGE 633
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Invalid messages/attributes skipped can occur in the following cases: ● The incoming GVRP PDU has an incorrect length. ● "End of PDU" was reached before the complete attribute could be parsed.
PAGE 634
20 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 5. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 634 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 635
Table 5. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 636
21 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
PAGE 637
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.
PAGE 638
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 639
Parameters Defaults access-list Enter the name of the extended ACL (16 characters maximum). Not configured Command Modes INTERFACE (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 640
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 641
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) For IGMP version 2, the Interval range is from 100 to 25599. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 642
Version Description 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.
PAGE 643
Version Description 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.
PAGE 644
Version Description 9.7(0.0) Added support for VRF and Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. Usage Information Mapping applies to both v1 and v2 IGMP joins; any updates to the ACL are reflected in the IGMP groups.
PAGE 645
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. show ip igmp groups View the IGMP groups.
PAGE 646
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series and C-Series. 7.5.1.
PAGE 647
Example (Details) 225.0.0.1 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.2 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.3 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.4 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 DellEMC# show ip igmp group details Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.
PAGE 648
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 649
IGMP immediate-leave is disabled IGMP activity: 0 joins IGMP querying router is 50.10.4.1 (this system) IGMP version is 3 Vlan 4007 Inbound IGMP access group is not set Internet address is 50.30.124.4/24 IGMP is up on the interface IGMP query interval is 60 seconds IGMP querier timeout is 83 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is disabled IGMP activity: 0 joins IGMP querying router is 50.30.124.
PAGE 650
Example Related Commands Version Description 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. DellEMC# show ip igmp ssm-map Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.5 00:01:22 ● ip igmp ssm-map — use a statically configured list to translate (*,G) memberships to (S,G) memberships.
PAGE 651
If the IP SA in the incoming IGMP general query frame is lower than the IP address of the VLAN interface, the switch disables its IGMP snooping Querier functionality. If the IP SA of the incoming IGMP general query is higher than the VLAN IP address, the switch continues to work as an IGMP snooping Querier. clear ip igmp snooping groups Clear snooping entries from the group cache table.
PAGE 652
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax debug ip igmp snooping [group address | interface] ● To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. ● To disable all debugging, use the undebug all command. Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 653
To disable IGMP snooping, use the no ip igmp snooping enable command. Defaults Disabled. Command Modes ● CONFIGURATION ● INTERFACE VLAN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 654
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.
PAGE 655
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 656
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 657
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 658
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 659
show ip igmp snooping mrouter Display multicast router interfaces. Syntax Parameters show ip igmp snooping mrouter [vlan number] vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 660
22 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • Basic Interface Commands Port Channel Commands Enhanced Validation of Interface Ranges ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 661
● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4. ● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport].
PAGE 662
Example Related Commands Version Description 6.5.1.0 Updated the definition of the learning-limit option for clarity. DellEMC# clear counters Clear counters on all interfaces [confirm] DellEMC# ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 663
Example Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 664
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 665
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 666
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. Defaults None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 667
full Defaults Enter the keyword full to set the physical interface to transmit in both directions. Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 668
Defaults Enabled Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S4048–ON and S5048F-ON. This feature is applicable only for 10GBase-T optical ports. NOTE: It is not supported for stacking ports. enable stack-unit phy temp polling Enable physical temperature polling for 10GBase-T optical ports.
PAGE 669
Usage Information Version Description 9.14(0.0) Introduced on the S4048–ON and S5048F-ON. This feature is applicable only for 10GBase-T optical ports. NOTE: It is not supported for stacking ports. encapsulation dot1q Configures lite-subinterfaces. Syntax encapsulation dot1q vlan-id To remove a previously configured lite-subinterface, use the no encapsulation dot1q vlan-id command. Parameters dot1q vlan-id Enter the keyword dot1q followed by the VLAN ID to which the host belongs.
PAGE 670
Defaults maclearnlimit Enter the keyword maclearnlimit to enable the timer to recover the interface from MAC learning limit error. arp-inspection Enter the keyword arp-inspection to enable the timer to recover the interface from an arp-inspection error. Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.
PAGE 671
fec default Set the FEC to default value. Syntax fec default Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 672
Usage Information Version Description 9.12(0.0) Enabled on 25G and 50G interfaces on the Z9100–ON by default. Introduced support to enable or disable FEC independent of autonegotiation for 100G interfaces on the S6100–ON and Z9100–ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 673
FEC status is cl74 OUI is 0x6a737d DellEMC(conf-if-fi-1/51/1)#do show int fi 1/51/1 fiftyGigE 1/51/1 is up, line protocol is up Hardware is DellEMCEth, address is 34:17:eb:37:0c:02 Current address is 34:17:eb:37:0c:02 Pluggable media present, QSFP28 type is 2x50GBASE-CR2-1M AutoNegotiation is ON Forward Error Correction(FEC) configured is cl108 FEC status is cl108 Related Commands fec default — sets the FEC to default value.show config — displays the interface configuration.
PAGE 674
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.0.0 Added support for the negotiate feature on the S4810 and S4820T. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 675
NOTE: Dell EMC Networking OS does not support mirroring of tx pause frames. Example Example (Monitor Session) DellEMC(conf-if-tf-1/1)# show config ! interface twentyFiveGigE 1/1 no ip address switchport no negotiation auto flowcontrol rx off tx on no shutdown ...
PAGE 676
interface Configure a physical or virtual interface on the switch. Syntax interface interface Parameters interface Enter one of the following keywords and the interface information: ● For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0. ● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 677
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport.
PAGE 678
Enter the member VLANs using VLAN IDs (separated by commas), a range of VLAN IDs (separated by a hyphen), a single VLAN ID, or a combination. For example: VLAN IDs (comma-separated): 3, 4, 6. Range (hyphen-separated): 5-10. Slot/Port information need not contain a space before and after the dash. For example, both of the following commands are valid: interface group twentyFiveGigE 1/1 - 1/4; interface group twentyFiveGigE 1/1-1/5 .
PAGE 679
interface loopback Configure a Loopback interface. Syntax interface loopback number To remove a loopback interface, use the no interface loopback number command. Parameters Defaults number Enter a number as the interface number. The range is from 0 to 16383. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 680
Parameters Defaults slot/port Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 681
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 682
{slot/ port[subport] | port} — {slot/ port[subport] | port},... Defaults ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport][/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information.
PAGE 683
Usage Information When creating an interface range, interfaces appear in the order they are entered; they are not sorted. The command verifies that interfaces are present (physical) or configured (logical). Important Points to Remember: ● Bulk configuration is created if at least one interface is valid. ● Non-existing interfaces are excluded from the bulk configuration with a warning message. ● The interface range prompt includes interface types with slot/port[/subport] information for valid interfaces.
PAGE 684
Example (Single Range) This example shows a single range bulk configuration. DellEMC(config)# interface range twentyFiveGigE 1/1 - 1/7 DellEMC(config-if-range-tf-1/1-1/7)# no shutdown Example (Multiple Range) This example shows how to use commas to add different interface types to a range of interfaces.
PAGE 685
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 686
define interface-range test twentyFiveGigE 1/1 - 1/3, twentyFiveGigE 1/5 - 1/7, twentyFiveGigE 1/11 - 1/18 DellEMC(config)# interface range macro test DellEMC(config-if-range-tf-1/1-1/3,tf-1/5-1/7,tf-1/11-1/18)# DellEMC(config)# define interface-range test HundredGigE 1/49 - 1/50, HundredGigE 1/52 - 1/53 DellEMC# show running-config | grep define define interface-range test HundredGigE 1/49 - 1/50, HundredGigE 1/52 1/53 DellEMC(config)# interface range macro test DellEMC(config-if-range-hu-1/49-1/50,hu-1/52
PAGE 687
Example (Single Range) This example shows the macro named test that was defined earlier. DellEMC(config)# interface range macro test DellEMC(config-if-range-tf-1/1-1/3,tf-1/4-1/6,tf-1/11-1/22)# Dell Related Commands ● interface range — configure a range of command (bulk configuration). ● interface range macro (define) — define a macro for an interface range (bulk configuration). interface vlan Configure a VLAN. You can configure up to 4094 VLANs.
PAGE 688
If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously. Example (Single Range) Related Commands DellEMC(conf)# int vlan 3 DellEMC(conf-if-vl-3)# ● ● ● ● ● ● ● ● interface — configure a physical interface. interface loopback — configure a loopback interface. interface null — configure a null interface. interface port-channel — configure a port channel group. show vlan — display the current VLAN configuration on the switch.
PAGE 689
Version Description 9.12(0.0) Introduced on the Z9100–ON. Example DellEMC(conf-if-fi-1/49/1)#intf-type cr2 autoneg DellEMC(conf-if-fi-1/49/1)#no intf-type cr2 autoneg intf-type cr4 autoneg Set the interface type as CR4 with auto-negotiation enabled. To set the interface type as CR4 with autonegotiation disabled, use the no intf-type cr4 autoneg command.
PAGE 690
Defaults Enabled. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.
PAGE 691
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 692
Example (Single Interface) Key Description r Change the [delta] column from change in the number of packets/bytes in the last interval to rate per second. l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis. a Change the view to the previous interface on the line card, or if in line card mode, the previous line card in the chassis. T Increase the screen refresh rate. t Decrease the screen refresh rate. q Return to the CLI prompt.
PAGE 693
To return to the default MTU value, use the no mtu command. Parameters Defaults value Enter a maximum frame size in bytes. The range is from 594 to 9416. The default is 1554. 1554 Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 694
● The VLAN link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the VLAN members. For example, the VLAN contains tagged members with Link MTU of 1522 and IP MTU of 1500 and untagged members with Link MTU of 1518 and IP MTU of 1500. The VLAN’s Link MTU cannot be higher than 1518 bytes and its IP MTU cannot be higher than 1500 bytes.
PAGE 695
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. This command is supported on 10/100/1000 Base-T Ethernet interfaces. You can use the negotiation auto command on the 10G ports on the device. The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits.
PAGE 696
Port 0 ● ● ● ● ● auto-negotiation auto-negotiation auto-negotiation auto-negotiation auto-negotiation enabled* speed 1000 or auto enabled speed 100 disabled speed 100 disabled speed 100 enabled* speed 1000 or auto Port 1 ● ● ● ● ● auto-negotiation auto-negotiation auto-negotiation auto-negotiation auto-negotiation enabled* speed 1000 or auto enabled speed 100 disabled speed 100 enabled speed 100 disabled speed 100 Link Status Between Port 1 and Port 2 ● ● ● ● ● Up at 1000 Mb/s Up at 100 Mb/s Up at 10
PAGE 697
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command-Line Reference Guide. Version Description 9.14(2.3) Introduced on the C9000, S3048-ON, S3100 series, S4048-ON, S4048T-ON, S5048F-ON, S6000, S6000-ON, S6010-ON, S6100-ON, and Z9100-ON. When you enable this feature, it allows you to set the delay timer value between 1 second to 300 seconds on all ports globally.
PAGE 698
Usage Information The following describes the interface command shown in the following example. This example sets a port as hybrid, makes the port a tagged member of VLAN 20, and an untagged member of VLAN 10, which becomes the native VLAN of the port. The port now accepts: ● untagged frames and classify them as VLAN 10 frames ● VLAN 20 tagged frames The following describes the do show interfaces command shown in the following example.
PAGE 699
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 700
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.0 Introduced on all Dell EMC Networking OS platforms. The output of the show interfaces command displays the configured rate interval, along with the collected traffic data. When rate-interval is not configured in the global configuration mode or interface mode, the default value of 299 seconds is applied.
PAGE 701
no ip address mtu 9416 switchport no shutdown DellEMC(conf-if-hu-1/49)# show config (from INTERFACE RANGE mode) Display the bulk configured interfaces (interface range). Syntax show config Command Modes CONFIGURATION INTERFACE (conf-if-range) Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 702
show interfaces Display information on a specific physical interface or virtual interface. Syntax show interfaces interface-type[—range] Parameters interface Enter one of the following keywords and the interface information: ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For stack-units, enter the keywords stack-unit then the slot/port information. ● For a Null interface, enter the keyword null then the Null interface number.
PAGE 703
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. Included display information about EEE on the S3100 series, S4820T, and S5000. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 704
Line Description Pluggable media present... Present pluggable media wavelength, type, and rate. The error scenarios are: ● Wavelength, unknown — Unable to determine the optics type ● Unknown — If the wavelength is reading an error Dell EMC Networking allows unsupported SFP and XFP transceivers to be used, but Dell EMC Networking OS might not be able to retrieve some data about them.
PAGE 705
Line Description ○ ○ ○ ○ ○ Example Vlans = number of VLAN tagged packets throttles = packets containing PAUSE frames discarded = number of packets discarded without any processing collisions = number of packet collisions wred=count both packets discarded in the MAC and in the hardware-based queues Rate information... Estimate of the input and output traffic rate over a designated interval (30 to 299 seconds). Traffic rate is displayed in bits, packets per second, and percent of line rate. Time since..
PAGE 706
Internet address is not set Mode of IPv4 Address Assignment : NONE DHCP Client-ID :3417eb2c8c82 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 25000 Mbit Flowcontrol rx off tx off ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 3d9h38m Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 runts, 0 giants, 0 th
PAGE 707
Queueing strategy: fifo Input 943 packets, 78347 bytes, 190 multicast Received 0 errors, 0 discarded Output 459 packets, 102388 bytes, 15 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:03:09 Example (Management Ethernet, two IPv6 addresses) DellEMC# show interfaces managementethernet 1/1 ManagementEthernet 1/1 is up, line protocol is up Hardware is DellForce10Eth, address is 00:01:e8:a0:bf:f3 Current address is 00:01:e8:a0:bf:f3 Pluggable media not present Interfa
PAGE 708
OUI is 0x6a737d Wavelength is 90nm Interface index is 2103820 Internet address is not set Mode of IPv4 Address Assignment : NONE DHCP Client-ID :3417eb373902 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 25000 Mbit Flowcontrol rx off tx off ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:06:57 Queueing strategy: fifo Input Statistics: 5441807056 packets, 348275680676 bytes 5441806949 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byt
PAGE 709
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000.
PAGE 710
show interfaces dampening Display interface dampening information. Syntax show interfaces dampening [[interface] [summary] [detail]] Parameters interface (Optional) Enter one of the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 711
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 712
Example Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 713
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in nonON platforms.
PAGE 714
Example DellEMC#show interfaces status Port Description Status Hu 1/49 Down Hu 1/50 Down Hu 1/51 Down Hu 1/52 Down Tf 1/1 Down Tf 1/2 Down Tf 1/3 Down Tf 1/4 Down Hu 1/53 Down Hu 1/54 Down Tf 1/9 Down Tf 1/7 Down Tf 1/8 Down Tf 1/5 Down Tf 1/10 Down Tf 1/11 Down Tf 1/12 Down Tf 1/13 Down Tf 1/14 Down Tf 1/15 Down Tf 1/16 Down Tf 1/17 Down Speed 100000 100000 100000 100000 25000 25000 25000 25000 100000 100000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 Duplex Vlan Mbit Auto -M
PAGE 715
● You can specify multiple ports as port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1 - 4.
PAGE 716
2/1 2/3 2/5 2/7 2/9 2/11 2/13 2/15 Quad Quad Quad Quad Quad Quad Quad Quad 10G 10G 10G 10G 10G 10G 10G 10G show interfaces switchport Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode interfaces’ IEEE 802.1Q tag status and VLAN membership.
PAGE 717
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.
PAGE 718
● show ip interface — display Layer 3 information about the interfaces. ● show interfaces transceiver — display the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show interfaces transceiver Display the details of an installed transceiver.
PAGE 719
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 720
Line Description Temp High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 721
Line Description RS state This is the reserved digital state of the pin AS(1) per SFF-8079 and RS(1) per SFF-8431. Tx Disable state If the admin status of the port is down then this flag is set to true. Temperature High Alarm Flag This can be either true or false, depending on the Current voltage value displayed above. Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above.
PAGE 722
SFP+ SFP+ SFP+ SFP+ 0x00 SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ 1/2 Id 1/2 Ext Id 1/2 Connector 1/2 Transceiver Code 0x00 0x00 1/2 Encoding 1/2 BR Nominal 1/2 Length(SFM) Km 1/2 Length(SFM) 100m 1/2 Length(OM3) 10m 1/2 Length(OM2) 10m 1/2 Length(OM1) 10m 1/2 Length(Copper-1m/AOC-1m/OM4-10m) 1/2 Vendor Name 1/2 Vendor PN 1/2 Trans Type 1/2 Vendor Rev 1/2 Laser Wavelength 1/2 CheckCodeBase 1/2 Serial Extended ID fields 1/2 Options 1/2 BR
PAGE 723
QSFP 49/1 Voltage Low Alarm threshold QSFP 49/1 Bias Low Alarm threshold QSFP 49/1 RX Power Low Alarm threshold =================================== QSFP 49/1 Temp High Warning threshold QSFP 49/1 Voltage High Warning threshold QSFP 49/1 Bias High Warning threshold QSFP 49/1 RX Power High Warning threshold QSFP 49/1 Temp Low Warning threshold QSFP 49/1 Voltage Low Warning threshold QSFP 49/1 Bias Low Warning threshold QSFP 49/1 RX Power Low Warning threshold =================================== QSFP 49/1 Temp
PAGE 724
Example Related Commands Version Description 8.2.1.0 Added support for 4093 VLANs on E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced. DellEMC(conf-if-range-tf-1/2,fo-1/49/1)# show range 1/2 - 0 1/49/1 - 0 ● interface — configure a physical interface on the switch. ● show ip interface — display Layer 3 information about the interfaces. shutdown Disable an interface.
PAGE 725
Disabling a VLAN or a port channel causes different behavior. When a VLAN is disabled, the Layer 3 functions within that VLAN are disabled. Layer 2 traffic continues to flow. Entering the shutdown command on a port channel disables all traffic on the port channel and the individual interfaces within the port channel. To enable a port channel, enter no shutdown on the port channel interface and at least one interface within that port channel.
PAGE 726
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Supported on LC-EH-GE-50P or the LC-EJ-GE-50P cards. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This command is found on the 10/100/1000/10000 Base-T Ethernet interfaces.
PAGE 727
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810 8.1.1.0 Introduced on the E-Series. 7.5.1.
PAGE 728
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Added support for dynamically fanning-out of interfaces on S6000.
PAGE 729
To remove an interface from Layer 2 mode and place it in Layer 3 mode, enter the no switchport command. If a switchport backup interface is configured, first remove the backup configuration. To remove a switchport backup interface, enter the no switchport backup interface command. Parameters backup (OPTIONAL) Use this option to configure a redundant Layer 2 link without using Spanning Tree.
PAGE 730
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.1.0 Added support for port-channel interfaces (the port-channel number option). 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Added the backup interface option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 731
Related Commands ● show config — displays the interface configuration. Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a Port Channel. ● The platform supports 1284096 port channels and 16 members per port channel.
PAGE 732
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 733
Command Modes PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 734
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series. 7.6.1.0 Introduced on S-Series. 7.5.1.0 Introduced on C-Series. pre-Version 6.2.1.
PAGE 735
minimum-links Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the LAG to be also in “oper up” status. Syntax Parameters Defaults minimum-links number number Enter the number of links in a LAG that must be in “oper up” status. The range is from 1 to 16. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 736
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 737
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the number of port channels to 4096. 9.9(0.
PAGE 738
Example Field Description Queueing strategy. States the packet queuing strategy. FIFO means first in first out. packets input... Displays the number of packets and bytes into the interface. Input 0 IP packets... Displays the number of packets with IP headers, VLAN tagged headers, and MPLS headers. The number of packets may not add correctly because a VLAN tagged IP packet counts as both a VLAN packet and an IP packet. 0 64-byte...
PAGE 739
Field Description Uptime Displays the age of the port channel in hours:minutes:seconds. Ports Lists the interfaces assigned to this port channel. (untitled) Displays the status of the physical interfaces (up or down). ● In Layer 2 port channels, an * (asterisk) indicates which interface is the primary port of the port channel. The primary port sends out interface PDU. ● In Layer 3 port channels, the primary port is not indicated.
PAGE 740
source-mac address destination-mac Enter the keywords source-mac then the MAC source address in the nn:nn:nn:nn:nn:nn format. address Enter the keywords destination-mac then the MAC destination address in the nn:nn:nn:nn:nn:nn format. vlan vlan-id Enter the keywords vlan then the VLAN-id. The range is from 0 to 4094. ether-type Enter the keywords ether-type in the XX:XX format. Command Modes EXEC Command History Usage Information This guide is platform-specific.
PAGE 741
Egress Port for port-channel 1, for the given flow, is Tf 1/2 Enhanced Validation of Interface Ranges You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as interface range hu 1/49,fo 1/50/1, this configuration is considered valid. The comma-separated list is not required to be separated by spaces in between the ranges.
PAGE 742
Interfaces Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.1) Introduced on the S4810, S4820T, S6000, and Z9000. 8.3.11.1 Introduced on the Z9000 8.2.1.0 Increased number of VLANs to 4094 (was 2094) 8.1.1.0 Introduced on E-Series 7.6.1.0 Support added for S-Series 7.5.1.
PAGE 743
23 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 744
• • • • • • • • show show show show show show show show ip management-route ipv6 management-route ip protocols ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 745
Usage Information Version Description 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series.
PAGE 746
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases.
PAGE 747
Usage Information In Dell EMC Networking OS versions prior to 8.3.1.0, if a gratuitous ARP is received some time after an ARP request is sent, only RP2 installs the ARP information. For example: 1. At time t=0, Dell EMC Networking OS sends an ARP request for IP A.B.C.D. 2. At time t=1, Dell EMC Networking OS receives an ARP request for IP A.B.C.D. 3. At time t=2, Dell EMC Networking OS installs an ARP entry for A.B.C.D only on RP2. Beginning with Dell EMC Networking OS version 8.3.1.
PAGE 748
Defaults 5 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 749
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 750
NOTE: Transit traffic may not be forwarded during the period when deleted ARP entries are resolved again and re-installed in CAM. Use this option with extreme caution. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 751
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 752
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.19.0 Introduced on the S4820T. Usage Information To clear Layer 3 CAM inconsistencies, use this command. Related Commands ● show ip fib stack-unit — show FIB entries on a specified stack-unit. CAUTION: Executing this command causes traffic disruption. clear ip route Clear one or all routes in the routing table.
PAGE 753
Usage Information Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Use the vrf vrf-name attribute of this command to clear routes corresponding to either a specific VRF or the default VRF. You cannot use this attribute to clear routes corresponding to a management VRF. Related Commands ● ip route — assign an IP route to the switch. ● show ip route — view the routing table.
PAGE 754
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. debug arp View information on ARP transactions. Syntax debug arp [interface] [count value] To stop debugging ARP transactions, use the no debug arp command. Parameters interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 755
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series(the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.
PAGE 756
Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series. Example Related Commands DellEMC# debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.17 BOOTP Request, hops = 0, XID = 0xbf05140f, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 0.0.0.
PAGE 757
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 758
ICMP: ICMP: ICMP: ICMP: Usage Information echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo reply src 40.40.40.40, dst 40.40.40.40, echo reply echo request sent to dst 40.40.40.40 To stop packets from flooding the user terminal when debugging is turned on, use the count option. debug ip packet View a log of IP packets sent and received.
PAGE 759
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Added the access-group option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option. The following describes the debug ip packet command in the following example.
PAGE 760
Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option. The access-group option supports only the equal to (eq) operator in TCP ACL rules. Port operators not equal to (neq), greater than (gt), less than (lt), or range are not supported in access-group option (refer to the following example). ARP packets (arp) and Ether-type (ether-type) are also not supported in the access-group option. The entire rule is skipped to compose the filter.
PAGE 761
secondary Defaults (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 762
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 763
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To configure a list of possible domain names, configure the ip domain-list command up to six times.
PAGE 764
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To fully enable DNS, also specify one or more domain name servers with the ip name-server command. Dell EMC Networking OS does not support sending DNS queries over a VLAN.
PAGE 765
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You can only configure one domain name with the ip domain-name command. To configure more than one domain name, configure the ip domain-list command up to six times.
PAGE 766
Usage Information Version Description 9.0.0.0 Added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. You can add multiple DHCP servers by entering the ip helper-address command multiple times.
PAGE 767
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced for the E-Series. Usage Information This command disables the incrementing of the hops field when boot requests are relayed to a DHCP server through Dell EMC Networking OS.
PAGE 768
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series.
PAGE 769
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 770
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 771
ip max-frag-count Set the maximum number of fragments allowed in one packet for packet re-assembly. Syntax ip max-frag-count count To place no limit on the number of fragments allowed, use the no ip max-frag-count command. Parameters Defaults count Enter a number for the number of fragments allowed for re-assembly. The range is from 2 to 256. No limit is set on number of fragments allowed. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 772
Parameters Defaults ipv4-address Enter the IPv4 address, in dotted decimal format, of the name server to be used. ipv4-address2... ipv4-address6 (OPTIONAL) Enter up five more IPv4 addresses, in dotted decimal format, of name servers to be used. Separate the addresses with a space. No name servers are configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 773
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 774
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information.
PAGE 775
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Included the weighted parameter to support weighted ECMP feature. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.
PAGE 776
DellEMC(conf)# ip route vrf test 1.1.1.0/24 6.6.6.2 weight 200 DellEMC(conf)# DellEMC(conf)# do show running-config | grep route ip route vrf test 1.1.1.0/24 4.4.4.2 weight 100 ip route vrf test 1.1.1.0/24 6.6.6.2 weight 200 Related Commands ● show ip route — view the switch routing table. ip source-route Enable Dell EMC Networking OS to forward IP packets with source route information in the header.
PAGE 777
ip tcp initial-time Define the wait duration in seconds for the TCP connection to be established. This command is supported on the , , , and platforms. Syntax ip tcp initial-time <8-75> To restore the default behavior, which causes the wait period to be set as 8 seconds, use the no ip tcp initial-time command. Parameters <8-75> Wait duration in seconds for the TCP connection to be established. Command Modes CONFIGURATION Command History Usage Information Version Description 9.12(1.
PAGE 778
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.
PAGE 779
Command Modes EXEC EXEC Privilege Command History Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.7(0.1) Introduced on the S3048-ON. 9.7(0.1) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages.
PAGE 780
load-balance By default, for C-Series and S-Series, Dell EMC Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 781
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Added the ingress-port parameter for the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 782
| dest-mac | dest-port-id | dest-module-id | vlan | ethertype | source-destmac ] tunnel [ ipv4over-ipv4 | ipv4over-gre-ipv4 | mac-in-mac ]} Defaults ● ● ● ● ● ● ● ● ● source-mac — Use source-mac field in hash calculation. source-port-id — Use src-port-id field in hash calculation. source-module-id — Use src-module-id field in hash calculation. dest-mac — Use dest-mac field in hash calculation. dest-port-id — Use dest-port-id field in hash calculation.
PAGE 783
Parameters ip-address mask Enter an IP address (dotted decimal format) and mask (/prefix format) of the destination subnet. ipv6-address prefix-length Enter an IPv6 address (x:x:x:x::x format) and mask (/prefix format) of the destination subnet. Enter the IPv6 address in the x:x:x:x::x format followed by the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 784
Management Connected prefix are not reflected in the hardware routing tables. Separate routing tables are maintained for IPv4 and IPv6 management routes. This command manages both tables. Related Commands ● interface ManagementEthernet — configure the Management port on the system (either the Primary or Standby RPM). ● speed (Management interface) — set the speed for the Management interface. show arp Display the ARP table.
PAGE 785
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 786
Description CPU Example Lists which CPU the entries are stored on. DellEMC> show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU ------------------------------------------------------------Internet 192.2.1.254 1 00:00:c0:02:01:02 Tf 1/1 CP Internet 192.2.1.253 1 00:00:c0:02:01:02 Tf 1/2 CP Internet 192.2.1.252 1 00:00:c0:02:01:02 Tf 1/3 CP Internet 192.2.1.251 1 00:00:c0:02:01:02 Tf 1/4 CP Internet 192.2.1.250 1 00:00:c0:02:01:02 Tf 1/5 CP Internet 192.2.1.
PAGE 787
Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 788
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6 addresses. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show hosts command in the following example.
PAGE 789
show ip cam stack-unit Display CAM entries for a port-pipe of a stack-unit on a S-Series or Z-Series switch. Syntax Parameters show ip cam stack-unit {stack-unit-number} [port-set {pipe-number} | vrf vrf-name {ip-address mask [longer-prefixes [ecmp-group detail]]}| ecmp-group {detail | member-info [detail [group-index index-number]]}| summary] stack-unitnumber Enter the stack-unit ID. The unit ID range is from 1 to 6.
PAGE 790
Usage Information Version Description 7.7.1.0 Added support for up to seven stack members. 7.6.1.0 Introduced on the S-Series. The following describes the show ip cam command shown in the following example. Field Description Destination Displays the destination route of the index. EC Displays 1 if the route is an ECMP route. Else, displays 0. C This is the CPU bit. If it displays 1, then it indicates that a packet hitting this entry will be forwarded to the CPU. V Id Displays the VLAN ID.
PAGE 791
Parameters stack-unitnumber Enter the stack unit ID. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view FIB entries corresponding to that VRF. ip-address mask (OPTIONAL) Enter the IP address of the network destination to view only information on that destination. Enter the IP address in dotted decimal format (A.B.C.D). Enter the mask in slash prefix format (/X). longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix.
PAGE 792
Field Description EC Displays the number of ECMP paths. If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named W-EC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is assigned with a weight. Example DellEMC# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC ------------------------------------------------------------------------------------------1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.
PAGE 793
src-port number Enter the keywords src-port then the source port number. destination-port Enter the keywords destination-port then the destination port number. number Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 794
show ip interface View IP-related information on all interfaces. Syntax show ip interface [interface | brief] [configured] Parameters interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information.
PAGE 795
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.2 Supported on the E-Series E600i. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 796
Fields Description Interface Displays type of interface and the associated slot and port number. IP-Address Displays the IP address for the interface, if configured. Ok? Indicates if the hardware is functioning properly. Method Displays “Manual” if the configuration is read from the saved configuration. Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface.
PAGE 797
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip management-route Destination ----------10.1.2.0/24 172.16.1.0/24 DellEMC# Gateway ------ManagementEthernet 0/0 10.1.2.
PAGE 798
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Introduced on the C- and E-Series. 8.3.7.0 Introduced on the S4810.
PAGE 799
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.3 Router Id is set to 20.20.20.
PAGE 800
connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes. all (OPTIONAL) Enter the keyword all to view both active and non-active routes. static (OPTIONAL) Enter the keyword static to view only routes the ip route command configures. summary (OPTIONAL) Enter the keyword summary. For more information, refer to the show ip route summary command. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 801
Field Description ● ● ● ● ● ● ● ● ● ● ● ● ● O = OSPF IA = OSPF inter area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes The weight for weighted ECMP route calculations is displayed for each path in the route in show ip route command.
PAGE 802
Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------*S 0.0.0.0/0 via 10.10.91.
PAGE 803
Routing Descriptor Blocks: * 4.4.4.2, via twentyFiveGigE 1/4 * 6.6.6.2, via twentyFiveGigE 1/16 DellEMC(conf)# show ip route list Display IP routes in an IP prefix list. Syntax Parameters show ip route [vrf vrf-name] list prefix-list prefix-list Enter the name of a configured prefix list. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IP routes in an IP prefix list corresponding to that VRF.
PAGE 804
N2- OSPF NSSA external type 2, E1 - OSPF external type 1, E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.0/24 2.1.3.0/24 2.1.4.0/24 Gateway ------via 2.1.4.1, Tf via 2.1.4.1, Tf via 2.1.4.1, Tf via 2.1.4.
PAGE 805
Usage Information Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example. Column Heading Description Route Source Identifies how the route is configured in Dell EMC Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources.
PAGE 806
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 807
Keyword Definition reply is not received, Dell EMC Networking OS repeats the request three times. These packets are counted in encapsulation failed. Rcvd: ...short packets The number of bytes in the packet are too small. ...bad length The length of the packet was not correct. ...no port broadcasts The incoming broadcast/multicast packet did not have any listener. ...socket full The applications buffer is full and the incoming packet are dropped.
PAGE 808
show tcp statistics View information on TCP traffic through the switch. Syntax show tcp statistics {all | cp} Parameters all Enter the keyword all to view all TCP information. cp Enter the keyword cp to view only TCP information from the Control Processor. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 809
Example Field Description 0 packets with data after window Displays the number of packets and bytes received that exceed the switch’s window size. 0 packets after close Displays the number of packet received after the TCP connection was closed. 0 window probe packets... Displays the number of window probe and update packets received. 41 dup ack... Displays the number of duplicate acknowledgement packets and acknowledgement packets with data received. 10184 ack...
PAGE 810
24 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 811
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax Parameters clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 812
Defaults warningthreshold Warning threshold value is expressed as a percentage of the limit value. When the number of IPv6 routes reaches the specified percentage of the limit, a warning message is generated. Valid range is 1 to 100. When warn-threshold is used, once the limit is reached, additional routes will not be allowed into the RTM ( route table manager ) itself.
PAGE 813
Usage Information Example Version Description 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can use this command to view the number of supported extended prefix entries in LPM configured. The output also displays the current applied value and the new value that is applicable after the reboot of the device.
PAGE 814
To restore to default, use the no ipv6 nd disable-reachable-timer command. Default Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.
PAGE 815
Example DellEMC(conf-if-tf-1/1)# ipv6 nd dns-server 1000::1 1 ipv6 route Establish a static IPv6 route. Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [name description] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
PAGE 816
permanent (OPTIONAL) Enter the keyword permanent to specify that the route is not to be removed, even if the interface assigned to that route goes down. NOTE: If you disable the interface with an IPv6 address associated with the keyword permanent, the route disappears from the routing table. weight weight- Enter the keyword weight followed by a weight value. The range is from 0 to 255.
PAGE 817
Example Related Commands DellEMC(conf)# DellEMC(conf)# DellEMC(conf)# DellEMC(conf)# DellEMC(conf)# DellEMC(conf)# ipv6 route 44::/64 33::1 weight 100 ipv6 route 44::/64 33::2 weight 200 do show running-config | grep ipv6 route ipv6 route vrf vrf_test 44::/64 33::1 weight 100 ipv6 route vrf vrf_test 44::/64 33::2 weight 200 do show running-config | grep ipv6 route vrf ● show ipv6 route — view the IPv6 configured routes. show ipv6 route Displays the IPv6 routes.
PAGE 818
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.4.1.
PAGE 819
O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, Gateway of last resort is not set Destination Dist/Metric, Gateway, Last Change ----------------------------------------------------C 100::/64 [0/0] Direct, Tf 1/12, 20:00:18 C 400::/64 [0/0] Direct, Tu 1, 00:09:02 S 800::/64 [1/0] via 100::1, Tf 1/12, 00:00:50 L f
PAGE 820
25 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 821
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 822
Version Description 7.8.1.0 Introduced on the C-Series. Example Example (Manual Profiles) DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) L2Acl : 2 Ipv4Acl : 2 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 3 -- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs.
PAGE 823
Command History Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters.
PAGE 824
Defaults destination address Enter the IPv6 address of the network or host to which the packets are sent in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. The :: notation specifies successive hexadecimal fields of zero. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes.
PAGE 825
Defaults ipv6 Enter the keyword ipv6 to filter any internet Protocol version 6. tcp Enter the keyword tcp to filter the Transmission Control protocol. udp Enter the keyword udp to filter the User Datagram Protocol. Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 826
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. ipv6 access-list Configure an access list based on IPv6 addresses or protocols. Syntax ipv6 access-list access-list-name cpu-qos To delete an access list, use the no ipv6 access-list access-list-name command. Parameters Defaults access-list-name Enter the access list name as a string, up to 140 characters.
PAGE 827
Usage Information Version Description 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters. Prior to version 7.8.1.0, names are up to 16 characters long. 7.4.1.0 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification on entries allowed per ACL, refer to your line card documentation.
PAGE 828
Usage Information Version Description 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. For the new settings to take effect, save the new CAM settings to the startup-config (write-mem or copy run start), then reload the system. The total amount of space allowed is 4 FP Blocks.
PAGE 829
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.2.0 Introduced on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 830
26 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 831
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 832
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
PAGE 833
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2.
PAGE 834
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain.
PAGE 835
clear isis Restart the IS-IS process. All IS-IS data is cleared. Syntax Parameters clear isis [vrf vrf-name] [tag] {* | database | traffic} vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to restart the IS-IS process corresponding to that VRF. tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process.
PAGE 836
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 837
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Entering debug isis enables all debugging parameters. To display all debugging information in one output, use this command. To turn off debugging, you normally enter separate no forms of each command. To disable all debug messages for IS-IS at once, enter the no debug isis command.
PAGE 838
Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information.
PAGE 839
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced.
PAGE 840
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced.
PAGE 841
Version Description 6.3.1.0 Introduced. debug isis update-packets Enable debugging on link state PDUs (LSPs) that a router detects. Syntax debug isis [vrf vrf-name] update-packets [interface] To turn off debugging, use the no debug isis update-packets [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS. This information contains updates from neighbors tied to the VRF that you specify.
PAGE 842
Version Description 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information. Syntax default-information originate [always] [metric metric] [route-map map-name] To disable the generation of a default route into the specified IS-IS routing domain, use the no default-information originate [always] [metric metric] [route-map map-name] command.
PAGE 843
How a metric value assigned to a default route advertises depends on the metric-style command configuration. If the metric-style command is set for Narrow mode and the metric value in the default-information originate command is set to a number higher than 63, the metric value advertised in the LSPs is 63. If the metric-style command is set for Wide mode, the metric value in the default-information originate command is advertised.
PAGE 844
Parameters Defaults weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability. Routes with smaller values are given preference.) The default is 115. ip-address mask (OPTIONAL) Enter the next-hop address in dotted decimal format and enter a mask in either dotted decimal or /prefix format. prefix-list (OPTIONAL) Enter the name of a prefix list name.
PAGE 845
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 846
Parameters Defaults prefix-list-name Specify the prefix list to filter prefixes in routing updates. connected (OPTIONAL) Enter the keyword connected for directly connected routing process. ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number. The range is from 1 to 65535. rip (OPTIONAL) Enter the keyword rip for RIP routes.
PAGE 847
● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 848
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced.
PAGE 849
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced on the E-Series. Every graceful restart enabled router’s HELLO PDUs includes a restart TLV. This restart enables (re)starting as well as the existing ISIS peers to detect the GR capability of the routers on the connected network.
PAGE 850
graceful-restart restart-wait Enable the graceful restart maximum wait time before a restarting peer comes up. Syntax NOTE: Set the t3 timer to adjacency on the restarting router when implementing this command. graceful-restart restart-wait seconds To return to the default, use the no graceful-restart restart-wait command. Parameters Defaults seconds Enter the graceful restart time in seconds. The range is from 5 to 300 seconds. The default is 30 seconds.
PAGE 851
retry-times Defaults Enter the keywords retry-times to set the number of times the request interval is extended until a CSNP is received from the helping router. The range is from 1 to 10 attempts. The default is 1. See Parameters. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 852
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 853
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. The running router sets the remaining time value to the current adjacency hold time. You can override this setting by implementing this command. Override the default restart-wait time by entering the no graceful-restart restart-wait command. When you disable restart-wait, the current adjacency hold time is used.
PAGE 854
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information IS-IS hellos are padded to the full maximum transmission unit (MTU) size. Padding IS-IS Hellos (IIHS) to the full MTU provides early error detection of large frame transmission problems or mismatched MTUs on adjacent interfaces. Related Commands ● isis hello padding — turn ON or OFF hello padding on an interface basis.
PAGE 855
To return to the default values, use the no ignore-lsp-errors command. Defaults In IS-IS, the default deletes LSPs with internal checksum errors (no ignore-lsp-errors). Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 856
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced.
PAGE 857
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Configure a network entity title (the net command) to specify the area address and the router system ID. To establish adjacencies and establish dynamic routing, enable routing on one or more interfaces.
PAGE 858
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Because the default establishes Level 1 and Level 2 adjacencies, you do not need to configure this command. Routers in an IS-IS system must be configured as a Level 1-only, Level 1-2, or Level 2-only system.
PAGE 859
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The default values of this command are typically satisfactory transmission times for a specific interface on a designated intermediate system. To maintain database synchronization, the designated routers send CSNPs. You can configure Level 1 and Level 2 CSNP intervals independently. isis hello-interval Specify the length of time between hello packets sent.
PAGE 860
Usage Information Hello packets are held for a length of three times the value of the hello interval. To conserve bandwidth and CPU usage, use a high hello interval seconds. Use a low hello interval seconds for faster convergence (but uses more bandwidth and CPU resources). Related Commands ● isis hello-multiplier — specify the number of IS-IS hello packets a neighbor must miss before the router declares the adjacency as down.
PAGE 861
isis hello padding Turn ON or OFF padding of hello PDUs from INTERFACE mode. Syntax isis hello padding To return to the default, use the no isis hello padding command. Defaults Padding of hello PDUs is enabled (ON). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 862
Defaults default-metric = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 863
Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 864
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. isis password Configure an authentication password for an interface. Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [password] [level-1 | level-2] command. Parameters Defaults encryption-type (OPTIONAL) Enter 7 to encrypt the password using DES.
PAGE 865
You can assign different passwords for different routing levels by using the keywords level-1 and level-2. The no form of this command disables the password for Level 1 or Level 2 routing, using the respective keywords level-1 or level-2. This password provides limited security as it is processed as plain text. isis priority Set the priority of the designated router you select.
PAGE 866
is-type Configure IS-IS operating level for a router. Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters Defaults level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. level-1-2 Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific.
PAGE 867
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 868
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 869
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.
PAGE 870
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The refresh interval determines the rate at which route topology information is transmitted preventing the information from becoming obsolete.
PAGE 871
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. To configure the number of area addresses on router, use this command. This value must be consistent with routers in the same area, otherwise the router forms only Level 2 adjacencies. The value must be same among all the routers to form Level 1 adjacencies. max-lsp-lifetime Set the maximum time that link-state packets (LSPs) exist without being refreshed.
PAGE 872
maximum-paths Allows you to configure the maximum number of equal cost paths allowed in a routing table. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 addresses. Syntax maximum-paths number To return to the default values, use the no maximum-paths command. Parameters Defaults number Enter a number as the maximum number of parallel paths an IP routing installs in a routing table. The range is from 1 to 64. The default is 4.
PAGE 873
Defaults transition Allows you to generate both old-style and new-style TLVs. The metric range is from 0 to 63. wide Allows you to generate and accept only new-style TLVs. The metric range is from 0 to 16777215. level-1 Enables the metric style on Level 1. level-2 Enables the metric style on Level 2. narrow; if no Level is specified, Level-1 and Level-2 are configured. Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific.
PAGE 874
Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 875
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface.
PAGE 876
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Although the passive interface does not send nor receive routing updates, the network on that interface is still included in the IS-IS updates sent using other interfaces.
PAGE 877
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 878
level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only. This setting is the default. metric metric- (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0.
PAGE 879
! router isis redistribute bgp 1 level-1 metric 32 metric-type external route-map rmap-isis-to-bgp redistribute ospf Redistribute routing information from an OSPF process.
PAGE 880
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced.
PAGE 881
Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Configure a network entity title (the net command) to specify the area address and the router system ID. Enable routing on one or more interfaces to establish adjacencies and establish dynamic routing.
PAGE 882
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.0 Introduced. Set the overload bit when a router experiences problems, such as a memory shortage due to an incomplete link state database which can result in an incomplete or inaccurate routing table. If you set the overload bit in its LSPs, other routers ignore the unreliable router in their SPF calculations until the router has recovered.
PAGE 883
set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family Example (AddressFamily_IPv6) The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode. DellEMC(conf-router_isis-af_ipv6)# show conf ! address-family ipv6 unicast maximum-paths 16 multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database.
PAGE 884
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added supported for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810. The following describes the show isis database command shown in the following example.
PAGE 885
ISIS.00-00 * 0x00000006 0xCF43 580 0/0/0 IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x00000006 0xCF43 580 0/0/0 ! DellEMC# show isis database detail ISIS.00-00 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002B 0x853B 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.1 IPv6 Address: 1011::1 Topology: IPv4 (0x00) IPv6 (0x8002) Metric: 10 IS OSPF.
PAGE 886
Parameters Command History Example vrf vrf-name (Optional) Enter the keyword vrf followed by the name if the VRf to display IS-IS graceful restart details corresponding to that VRF. NOTE: If you do not specify this option, the IS-IS graceful restart details corresponding to the default VRF are displayed. This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 887
Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IS-IS host names corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 888
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Example 888 This guide is platform-specific.
PAGE 889
show isis neighbors Display information about neighboring (adjacent) routers. Syntax Parameters show isis [vrf vrf-name] neighbors [level-1 | level-2] [detail] [interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display adjacent router information corresponding to that VRF. level-1 (OPTIONAL) Displays information about Level 1 IS-IS neighbors. level-2 (OPTIONAL) Displays information about Level 2 IS-IS neighbors.
PAGE 890
Usage Information Use this command to confirm that the neighbor adjacencies are operating correctly. If you suspect that they are not, you can verify the specified area addresses of the routers by using the show isis neighbors command. The following describes the show isis neighbors command shown in the following example. Example Field Description System Id The value that identifies a system in an area. Interface The interface, slot, and port in which the router was discovered.
PAGE 891
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 892
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 892 This guide is platform-specific.
PAGE 893
Example Item Description Level-1/Level-2 DR Elections Displays the number of times designated router elections ran. Level-1/Level-2 SPF Calculations Displays the number of shortest path first calculations. LSP checksum errors received Displays the number of checksum errors LSPs received. LSP authentication failures Displays the number of LSP authentication failures.
PAGE 894
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 895
27 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 896
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters Defaults time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 897
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.
PAGE 898
iscsi priority-bits Configure the priority bitmap that advertises in the iSCSI application TLVs. Syntax iscsi priority-bits To remove the configured priority bitmap, use the no iscsi priority-bits command. Defaults 4 (0x10 in the bitmap) Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 899
iscsi target port Configure the iSCSI target ports and optionally, the IP addresses on which iSCSI communication is monitored. Syntax iscsi target port [tcp-port-2...tcp-port-16]ip-address [ip-address] To remove the configured iSCSI target ports or IP addresses, use the no iscsi target port command. Parameters tcpEnter the tcp-port number of the iSCSI target ports. The tcp-port-n is the TCP port-2...tcpport- port number or a list of TCP port numbers on which the iSCSI target listens to 16 requests.
PAGE 900
Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module.
PAGE 901
iom010 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000 Session 1: --------------------------------------------------------Target: iqn.2001-05.com.equallogic:0-8a0906-0f60c2002-0360018428d48c94iom011 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000. Usage Information Only sessions the switch observes are learned; sessions flowing through an adjacent switch are not learned.
PAGE 902
IP Address TCP Port IP Address TCPPort ID 10.10.0.44 33345 10.10.0.101 3260 0 Session 1 : ---------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-35 Up Time:00:00:01:22(DD:HH:MM:SS) Time for aging out:00:00:09:31(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.53 33432 10.10.0.
PAGE 903
28 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 904
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on).
PAGE 905
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series.
PAGE 906
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command applies to dynamic port-channel interfaces only. When applied on a static port-channel, this command has no effect. Related Commands ● show lacp — display the LACP configuration.
PAGE 907
Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp system-priority Configure the LACP system priority. Syntax Parameters Defaults lacp system-priority priority-value priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. 32768 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 908
Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 909
Example (PortChannelNumber) Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 910
29 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 911
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. ● mac learning-limit — set the MAC address learning limits for a selected interface. ● show mac-address-table aging-time — display the MAC aging time.
PAGE 912
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. vlan vlan-id Defaults Enter the keyword vlan then a VLAN ID number from 1 to 4094. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 913
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Modified the default option from none to Enabled. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 914
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 915
mac learning-limit learn-limit-violation Configure an action for a MAC address learning-limit violation. Syntax mac learning-limit learn-limit-violation {log | shutdown} To return to the default, use the no mac learning-limit learn-limit-violation {log | shutdown} command. Parameters Defaults log Enter the keyword log to generate a syslog message on a learning-limit violation. shutdown Enter the keyword shutdown to shut down the port on a learning-limit violation.
PAGE 916
To convert the sticky MAC addresses to dynamic MAC addresses, use the no mac learning-limit command. Parameters Defaults mac-addresssticky Configures the dynamic MAC addresses as sticky on an interface. None Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 917
shutdownoriginal Defaults Enter the keywords shutdown-original to shut down the original interface and generate a syslog message. None Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 918
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 919
show mac-address-table Display the MAC address table. Syntax Parameters show mac-address-table [address mac-address | interface interface | vlan vlan-id] [aging-time] [dynamic | static] [count [vlan vlan-id] [interface interface-type [slot [/port[/subport]]]]] address mac- address (OPTIONAL) Enter the keyword address then a MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address.
PAGE 920
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Updated the output. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.
PAGE 921
Example (Count) Related Commands Line Beginning With Description MAC Entries... Displays the number of MAC entries learned per VLAN. Dynamic Address... Lists the number of dynamically learned MAC addresses. Static Address... Lists the number of user-defined MAC addresses. Total MAC... Lists the total number of MAC addresses the switch uses.
PAGE 922
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series and S-Series. pre-6.2.1.1 Introduced on the E-Series. DellEMC# show mac-address-table aging-time Mac-address-table aging time : 1800 DellEMC# Related Commands ● show mac-address-table — display the current MAC address configuration.
PAGE 923
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on E-Series. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.
PAGE 924
Parameters Defaults vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 925
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.3.1.1 Introduced on the E-Series.
PAGE 926
Usage Information The no default vlan disable command is not listed in the running-configuration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters Defaults vlan-name Enter up to 32 characters as the name of the VLAN. Not configured. Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 927
show config Display the current configuration of the selected VLAN. Syntax show config Command Modes INTERFACE VLAN Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 928
● MAC address aging time ● IP address id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094. Only information on the VLAN specified is displayed. name vlan-name (OPTIONAL) Enter the keyword name then the name configured for the VLAN. Only information on the VLAN named is displayed. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 928 Layer 2 This guide is platform-specific.
PAGE 929
Column Heading Description Status Displays the word Inactive for inactive VLANs and the word Active for active VLANs. Q ● ● ● ● ● ● ● ● ● ● ● ● ● Ports Displays the type, slot, and port information.
PAGE 930
Example (VLAN ID) DellEMC# show vlan id 40 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 40 Status Description Q Ports Active M Tf 1/47 DellEMC# show vlan id 41 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 41 Status Description Q Ports Active T Tf 1/47 DellEMC# show vlan id 42 Codes: Q: U x G - * - Default VLAN, G - G
PAGE 931
tagged Add a Layer 2 interface to a VLAN as a tagged interface. Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command. Parameters interface Enter the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 932
Usage Information When you use the no tagged command, the interface is automatically placed in the Default VLAN as an untagged interface unless the interface is a member of another VLAN. If the interface belongs to several VLANs, remove it from all VLANs to change it to an untagged interface. Tagged interfaces can belong to multiple VLANs, while untagged interfaces can only belong to one VLAN at a time. Related Commands ● interface vlan — configure a VLAN.
PAGE 933
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 934
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series.
PAGE 935
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 936
● aggressive: Change the link state to “error-disabled” when a far-end failure is detected by the software on that interface. When an interface is placed in an “error-disabled” state, you must enter the fefd reset command to reset the interface state. Range is normal or aggressive. Default is normal. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 937
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command.
PAGE 938
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information You can set up the interval between control packets using the fefd interval command. Related Commands ● fefd — enable far-end failure detection. fefd mode Change the FEFD mode on an interface.
PAGE 939
Version Description Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. fefd reset Reset all interfaces or a single interface that was in “error-disabled” mode. Syntax Parameters fefd reset [interface] interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 940
fefd-global interval Configure an interval between FEFD control packets. Syntax fefd-global interval seconds To return to the default value, use the no fefd-global interval command. Parameters Defaults seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds. 15 seconds Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 941
aggressive Defaults (OPTIONAL) Enter the keywords mode aggressive to change the link state to “error-disabled” when a far-end failure the software detects on that interface. When an interface is placed in “error-disabled” state, t enter the fefd reset command to reset the interface state. Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 942
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 943
Tf 1/1 Tf 1/2 Tf 1/3 Tf 1/4 Tf 1/5 Tf 1/6 Tf 1/7 Tf 1/8 Tf 1/9 Tf 1/10 Tf 1/11 DellEMC# Related Commands ● ● ● ● Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive NA Aggressive (second) 10 10 10 10 10 10 10 10 10 NA 10 Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Locally disabled Err-disabled fefd — enable far-end failure detection.
PAGE 944
30 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 945
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
PAGE 946
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor.
PAGE 947
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 948
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 949
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. Defaults all Enter the keyword all to display information on all interfaces. events Enter the keyword events to display major events such as timer events. packet Enter the keyword packet to display information regarding packets coming in or going out.
PAGE 950
Dec Dec Dec Dec Dec 4 4 4 4 4 22:38:29 22:38:29 22:38:29 22:38:29 22:38:29 : TLV: UNKNOWN TLV, ORG_SPEC[aa-bb-cc, 4], Len: 1, Value:a : aa bb cc 04 61 : 40 : TLV: UNKNOWN TLV, Type: 125 Len: 1, Value: @ : TLV: ENDOFPDU, Len: 0 disable Enable or disable LLDP. Syntax disable To enable LLDP, use the no disable command. Defaults Enabled — no disable. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History Related Commands This guide is platform-specific.
PAGE 951
To revert to the default, use the no hello seconds command. Parameters Defaults seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds. 30 seconds Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 952
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 953
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch.
PAGE 954
Version Description 7.4.1.0 Introduced on the E-Series. protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History Usage Information This guide is platform-specific.
PAGE 955
show lldp neighbors Display LLDP neighbor information for all interfaces or a specified interface. Syntax Parameters show lldp neighbors [interface interface] [detail] interface interface detail Defaults (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information.
PAGE 956
Example Example (Detail) DellEMC(conf-if-tf-1/31)# do show lldp neighbors Loc PortID Rem Host Name Rem Port Id Rem Chassis Id -------------------------------------------------------------Tf 1/21 R2 twentyFiveGigE 1/11 00:01:e8:06:95:3e Tf 1/31 R3 twentyFiveGigE 1/11 00:01:e8:09:c2:4a DellEMC#show lldp neighbors detail ======================================================================== Local Interface Tf 1/4 has 1 neighbor Total Frames Out: 6547 Total Frames In: 4136 Total Neighbor information Age out
PAGE 957
( 88, 4) ( 98, 4) (108, 4) (118, ( 79, 4) ( 80, 4) ( 81, 4) ( 82, 4) ( 83, 4) ( 84, 4) ( 85, 4) ( 86, 4) ( 87, 4) ( 89, 4) ( 90, 4) ( 91, 4) ( 92, 4) ( 93, 4) ( 94, 4) ( 95, 4) ( 96, 4) ( 97, 4) ( 99, 4) (100, 4) (101, 4) (102, 4) (103, 4) (104, 4) (105, 4) (106, 4) (107, 4) (109, 4) (110, 4) (111, 4) (112, 4) (113, 4) (114, 4) (115, 4) (116, 4) (117, 4) 4) (119, 4) (120, 4) (121, 4) (122, 4) (123, 4) (124, 4) (125, 4) (126, OrgUnknownTLVList: -----------------
PAGE 958
Information valid for next 199 seconds Time since last information change of this neighbor: 00:01:41 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),120, 4) ((00-01-66),119, ((00-01-66),118, 4) --------------------------------------------------------------------------- 4) 4) show lldp statistics Display the LLDP statistical information.
PAGE 959
LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands. Dell EMC Networking OS LLDP-MED commands are an extension of the set of LLDP TLV advertisement commands. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information.
PAGE 960
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● protocol lldp (Configuration) — enable LLDP globally. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 961
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system.
PAGE 962
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Usage Information ● ECS — Emergency call service such as defined by TIA or the national emergency numbering association (NENA) ● ELIN — Emergency location identification number, a valid North America Numbering Plan format telephone number supplied for ECS purposes.
PAGE 963
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 964
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med video-conferencing To advertise dedicated video conferencing and other similar appliances that support real-time interactive video, configure the system.
PAGE 965
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system.
PAGE 966
Related Commands Version Description 7.6.1.0 Introduced on the C-Series and E-Series. ● ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system.
PAGE 967
advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system. Syntax advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority.
PAGE 968
31 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 969
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.3(0.0) Added support for association of an IP address with multicast MAC address on the S4810, S4820T, S6000, and Z9000 platforms. Usage Information For multicast mode of NLB, to associate an IP address with a multicast MAC address in the switch, use address resolution protocol (ARP) by entering the arp ip-address multicast-mac-address command in Global configuration mode.
PAGE 970
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a Management interface, enter the keyword managementethernet followed by slot/port numbers. ● For a Port Channel interface, enter the keywords port-channel followed by a number.
PAGE 971
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms. Default Disabled Usage Information By default this command is disabled. There might be some ARP table entries which are resolved through ARP packets which had Ethernet MAC SA different from MAC information inside the ARP packet.
PAGE 972
32 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the platform.
PAGE 973
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 974
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax clear ip msdp statistic peer peer-address Parameters Defaults peer Enter the keyword peer to clear the MSDP peer entries.
PAGE 975
ip msdp cache-rejected-sa Enable an MSDP cache for the rejected source-active entries. Syntax ip msdp cache-rejected-sa {number} To clear the MSDP rejected source-active entries, use the no ip msdp cache-rejected-sa {number} command then the ip msdp cache-rejected-sa {number} command. Parameters Defaults number Enter the number of rejected SA entries to cache. The range is from 0 to 32766. None Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 976
list name Defaults Enter the keywords list name and specify a standard access list that contains the RP address that should be treated as the default peer. If no access list is specified, then all SAs from the peer are accepted. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 977
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.
PAGE 978
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced An MSDP mesh group is a mechanism for reducing SA flooding, typically in an intra-domain setting. When some subset of a domain’s MSDP speakers are fully meshed, they can be configured into a mesh-group.
PAGE 979
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 6.2.1.1 Introduced ip msdp peer Configure an MSDP peer.
PAGE 980
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 981
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 982
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the E-Series.
PAGE 983
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the E-Series. Dell EMC Networking OS counts the SA messages originated by itself and those messages received from the MSDP peers. When the total SA messages reach this limit, the subsequent SA messages are dropped (even if they pass RPF checking and policy checking).
PAGE 984
ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 985
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 986
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example 986 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 987
33 Multicast Listener Discovery Protocol The Multicast Listener Discovery (MLD) protocol is used by IPv6 routers to discover multicast listeners on a directly attached link. Similar to the Internet Group Management Protocol (IGMP), which handles multicast group memberships in IPv4 networks, MLD is used for multicast management on IPv6 networks.
PAGE 988
debug ipv6 mld Enable debugging on IPv6 MLD packets. Syntax debug ipv6 mld [vrf vrf-name] {group-address | interface} To turn off debugging, use the no debug ipv6 mld {group-address | interface} command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format. The :: notation specifies successive hexadecimal fields of zero.
PAGE 989
To return to the default, use the no ipv6 mld last-member-query-interval {milliseconds} command. Parameters Defaults milliseconds Enter the last member query interval in milliseconds. The range is from 100 to 65535. 1000 milliseconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.
PAGE 990
ipv6 mld version Configure the MLD version on the system. Syntax ipv6 mld version {1 | 2} Defaults MLD version 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 991
Example Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Reporter Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires Last 00:02:05 1::2 show ipv6 mld interface View the configured MLD interfaces. Syntax Parameters show ipv6 mld [vrf vrf-name] interface [interface] vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF.
PAGE 992
clear ipv6 mld snooping groups Clear entries from the group cache table. Syntax clear ipv6 mld snooping groups [interface | group-address] Parameters interface Enter the following keywords and slot/port or number information: ● For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number.
PAGE 993
ipv6 mld snooping Enable MLD snooping on a VLAN. Syntax ipv6 mld snooping To disable MLD snooping, use the no ipv6 mld snooping command. Defaults Enabled on all VLAN interfaces. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 994
ipv6 mld snooping mrouter Configure a Layer 2 port as a multicast router port. Syntax ipv6 mld snooping mrouter interface {interface interface} Parameters interface Enter the keyword interfaceto indicate the next-hop interface to the multicast router. interface Enter one of the following keywords and the interface information: ● For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0.
PAGE 995
show ipv6 mld snooping groups Display the IPv6 MLD snooping group information. Syntax Parameters show ipv6 mld snooping groups [group address] [summary] [interface interface [detail]] group-address (Optional) Enter the multicast group addresss in the X:X:X:X::X format. The :: notation specifies successive hexadecimal fields of zero. summary (OPTIONAL) Enter the keyword summary to display a summary of groups.
PAGE 996
Example Version Description 9.14(1.0) Updated the output to show both MLD versions 1 and 2. 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 997
34 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 998
Optionally, enter an in or out parameter with the optional interface: ● For Receive, enter the keyword in. ● For Transmit, enter the keyword out. events (OPTIONAL) Enter the keyword events to debug MSTP events. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 999
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1000
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced.
PAGE 1001
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● forward-delay — amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. ● max-age — change the wait time before MSTP refreshes protocol configuration information.
PAGE 1002
Related Commands Version Description 6.5.1.0 Introduced. ● forward-delay — amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. ● hello-time — change the time interval between BPDUs. msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance.
PAGE 1003
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. By default, all VLANs are mapped to MST instance zero (0) unless you use the vlan range command to map it to a non-zero instance. name The name you assign to the multiple spanning tree region. Syntax name region-name To remove the region name, use the no name command. Parameters Defaults region-name Enter the MST region name. The range is 32 character limit. No default name.
PAGE 1004
port-channel path-cost custom Sets the path cost to be constant for port-channel regardless of its operation status. Syntax port-channel path-cost custom To change the path cost to comply with new IEEE standard behavior, use no port-channel pathcost custom command. Defaults Disabled Command Modes SPANNING TREE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1005
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. MSTP is not enabled when you enter MULTIPLE SPANNING TREE mode. To enable MSTP globally on the switch, enter the no disable command while in MULTIPLE SPANNING TREE mode.
PAGE 1006
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information For two MSTP switches to be within the same MST region, the switches must share the same revision number. Related Commands ● msti — map the VLAN(s) to an MST instance.
PAGE 1007
Example DellEMC(conf-mstp)# show config ! protocol spanning-tree mstp no disable name CustomerSvc revision 2 MSTI 10 VLAN 101-105 max-hops 5 DellEMC(conf-mstp)# show spanning-tree mst configuration View the multiple spanning tree configuration. Syntax show spanning-tree mst configuration Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific.
PAGE 1008
show spanning-tree msti View the multiple spanning tree instance. Syntax show spanning-tree msti [instance-number [brief]] [guard] Parameters instance-number (Optional) Enter the multiple spanning tree instance number. The range is from 0 to 63. brief (Optional) Enter the keyword brief to view a synopsis of the MST instance. guard (Optional) Enter the keyword guard to display the type of guard enabled on an MSTP interface and the current port state.
PAGE 1009
Designated root has priority 16384, address 0001.e800.0a:5c Designated bridge has priority 32768, address 0001.e802.35:06 Designated port id is 128.82, designated path cost Number of transitions to forwarding state 1 BPDU (Mrecords): sent 1109, received 0 The port is not in the portfast mode Port 88 (twentyFiveGigE 1/6) is root Forwarding Port path cost 0, Port priority 128, Port Identifier 128.88 Designated root has priority 16384, address 0001.e800.0a:5c Designated bridge has priority 16384, address 0001.
PAGE 1010
Usage Information Example (Guard) The following describes the show spanning-tree msti 5 guard command shown in the following example. Field Description Interface Name MSTP interface. Instance MSTP instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1011
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface. Syntax Parameters spanning-tree msti instance {cost cost | priority priority} msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value.
PAGE 1012
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled.
PAGE 1013
35 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • IPv4 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1014
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 1015
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1016
Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system.
PAGE 1017
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
PAGE 1018
Querying reverse path for source 103.103.103.3 to destination 1.1.1.1 via group 226.0.0.3 From source (?) to destination (?) ----------------------------------------------------------------|Hop| OIF IP |Proto| Forwarding Code |Source Network/Mask| ----------------------------------------------------------------0 1.1.1.1 --> Destination -1 1.1.1.1 PIM Reached RP/Core 103.103.103.0/24 -2 101.101.101.102 PIM 103.103.103.0/24 -3 2.2.2.1 PIM 103.103.103.0/24 -4 103.103.103.
PAGE 1019
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Example DellEMC# show ip multicast-cam stack-unit 1 port 0 Vrf Id Group Address Source Address Vlan Id L3 Ports ----------------------------------------------------0 224.1.1.1 0.0.0.0 1000 tf 1/10, 0 224.1.1.2 0.0.0.0 1000 tf 1/10, 0 224.1.1.1 165.13.34.
PAGE 1020
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1021
Example (VLT) DellEMC# show ip mroute vlt IP Multicast Routing Table Flags: S – Synced (*, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Vlan 30 (50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information Example The following describes the show ip mroute command shown in the following example.
PAGE 1022
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1023
36 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1024
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to clear the neighbor corresponding to that VRF. NOTE: If you do not specify this option, the neighbors in the default VRF are cleared. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format to remove a specific IPv6 neighbor. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1025
debug ipv6 nd ra–guard Enable debugging for IPv6 RA guard snooping information. Syntax debug ipv6 nd ra-guard [interface_type slot/port | count value] Parameters interface_type slot/port count value Defaults Enter the one of the following interfaces and slot/port information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 1026
Defaults None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.
PAGE 1027
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. ● ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode. ipv6 nd ra–guard attach–policy Apply the IPv6 RA guard to a specific interface.
PAGE 1028
To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1029
Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. ipv6 neighbor Configure a static entry in the IPv6 neighbor discovery. Syntax ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} {hardware_address} To remove a static IPv6 entry from the IPv6 neighbor discovery, use the no ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} command.
PAGE 1030
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.
PAGE 1031
Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches.
PAGE 1032
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. ● ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode.
PAGE 1033
other–config–flag Enable the verification of the advertised other configuration parameter. If this command is not configured, the verification process is bypassed. Syntax other-config-flag {on | off} To reset the other configuration parameter, use the no other-config-flag {on | off} command. Parameters Defaults on Enter the keyword on to set the other-config-flag value as ON. off Enter the keyword off to set the other-config flag value as OFF.
PAGE 1034
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1035
Related Commands ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. ipv6 nd ra-guard enable — configure the RA guard related commands. router–lifetime Set the router lifetime. Syntax Parameters Defaults router—lifetime value value Enter the router lifetime in seconds. The range is from 0 to 9,000 seconds.
PAGE 1036
Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.
PAGE 1037
Example Related Commands DellEMC(conf)# ipv6 nd ra-guard policy test DellEMC(conf-ra_guard_policy_list)#show config ! ipv6 nd ra-guard policy test device-role router hop-limit maximum 251 mtu 1350 other-config-flag on reachable-time 540 retrans-timer 101 router-preference maximum medium trusted-port DellEMC(conf-ra_guard_policy_list)# ● ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1038
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Introduced on the S6000–ON, and Z9000 switches. DellEMC# show ipv6 nd ra-guard policy test ipv6 nd ra-guard policy test device-role router hop-limit maximum 1 match ra ipv6-access-list access other-config-flag on router-preference maximum medium trusted-port Interfaces : Tf 1/1 DellEMC# Related Commands ● ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1039
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 1040
trusted–port Allow bypassing the configured RA guard validation and forwards the RA packets received on the interface, which has the trusted port policy attached. Syntax trusted-port To reset the policy applied to the trusted port, use the no trusted-port command. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1041
37 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1042
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface twentyFiveGigE 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1043
If the state of an object changes back to its former UP/DOWN state before the timer expires, the timer is cancelled and the client is not notified. For example, if the DOWN timer is running when an interface goes down and comes back up, the DOWN timer is cancelled and the client is not notified of the event. If the timer expires and an object’s state has changed, a notification is sent to the client.
PAGE 1044
show running-config track Display the current configuration of tracked objects. Syntax show running-config track [object-id] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.
PAGE 1045
● track interface line-protocol – configure object tracking on the line-protocol state of a Layer 2 interface. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. ● track ip route reachability – configure object tracking on the reachability of an IPv4 route. show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1046
Output Description IPv6 route ipv6- address object is Up/ Down Up/Down state of tracked object; for example, IPv4 interface, reachability or metric threshold of an IP route. number changes, Number of times that the state of the tracked object has changed and the time last change time since the last change in hours:minutes:seconds. Example First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route.
PAGE 1047
threshold metric Configure the metric threshold used to determine the UP and/or DOWN state of a tracked IPv4 or IPv6 route. Syntax threshold metric {up number | down number} To return to the default setting, use the no threshold metric {up number | down number} command. Parameters Defaults up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254.
PAGE 1048
Related Commands ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. ● track resolution ip route – configure the protocol-specific resolution value used to scale an IPv4 route metric. track interface ip routing Configure object tracking on the routing status of an IPv4 Layer 3 interface. Syntax track object-id interface interface ip routing To return to the default setting, use the no track object-id command.
PAGE 1049
● The status of the IPv4 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IP address. ● The Layer 3 status of an IPv4 interface goes DOWN when its Layer 2 status goes down (for a Layer 3 VLAN, all VLAN ports must be down) or the IP address is removed from the routing table. Related Commands ● show track – display information about tracked objects, including configuration, current state, and clients which track the object.
PAGE 1050
Usage Information Version Description 8.4.1.0 Introduced. Use this command to create an object that tracks the line-protocol state of a Layer 2 interface by monitoring its operational status (UP or DOWN). When the link-level status goes down, the tracked object status is considered to be DOWN; if the linklevel status is up, the tracked object status is considered to be UP.
PAGE 1051
not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact IPv4 address and prefix length, the status of the tracked route is considered to be DOWN. When you configure the threshold of an IPv4 route metric as a tracked object, the UP/DOWN state of the tracked route is also determined by the current metric for the route in the routing table.
PAGE 1052
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv4 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.
PAGE 1053
Usage Information To disable the attempt to track the reachability of next-hop after the configured refresh interval, set the refresh interval as 0. Related Commands ● show track – display information about tracked objects, including configuration, current state, and clients which track the object. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric.
PAGE 1054
● The resolution value used to map RIP routes is not configurable. The RIP hop-count is automatically multiplied by 16 to scale it. For example, a RIP metric of 16 (unreachable) scales to 256, which considers the route to be DOWN. Related Commands ● threshold metric – configure the metric threshold used to determine the UP and/or DOWN state of a tracked route. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric.
PAGE 1055
Output Description Interface type Displays the interface type and slot/port number or address of the IPv4/IPv6 route slot/port , IP that is being tracked. route ip-address , IPv6 route ipv6- address object is Up/ Down Up/Down state of tracked object; for example, IPv4 interface, reachability or metric threshold of an IP route. number changes, Number of times that the state of the tracked object has changed and the time last change time since the last change in hours:minutes:seconds.
PAGE 1056
track interface ipv6 routing Configure object tracking on the routing status of an IPv6 Layer 3 interface. Syntax track object-id interface interface ipv6 routing To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 1057
Related Commands ● show track ipv6 route – display information about tracked IPv6 routes, including configuration, current state, and clients which track the route. ● track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface. track ipv6 route metric threshold Configure object tracking on the threshold of an IPv4 route metric.
PAGE 1058
You configure the UP and DOWN thresholds for each tracked IPv6 route by using the threshold metric command. The default UP threshold is 254; the default DOWN threshold is 255. The notification of a change in the state of a tracked object is sent when a metric value crosses a configured threshold. Related Commands ● show track ipv6 route – display information about tracked IPv6 routes, including configuration, current state, and clients which track the route.
PAGE 1059
If the next-hop address in the ARP cache ages out for a route tracked for its reachability, an attempt is made to regenerate the ARP cache entry to if the next-hop address appears before considering the route DOWN. Related Commands ● show track ipv6 route – display information about tracked IPv6 routes, including configuration, current state, and clients which track the route. ● track ipv6 route reachability – configure object tracking on the reachability of an IPv4 route.
PAGE 1060
● The resolution value used to map static routes is not configurable. By default, Dell EMC Networking OS assigns a metric of 0 to static routes. ● The resolution value used to map RIP routes is not configurable. The RIP hop-count is automatically multiplied by 16 to scale it. For example, a RIP metric of 16 (unreachable) scales to 256, which considers the route to be DOWN.
PAGE 1061
38 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1062
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1063
Version Description 9.13(0.0) Introduced on the remaining DNOS platforms. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1064
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1065
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1066
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.
PAGE 1067
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors.
PAGE 1068
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.
PAGE 1069
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.4(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 1070
Field Description to: Displays the interface to which the packet is intended. dst: Displays the destination IP address. netmask: Displays the destination IP address mask.
PAGE 1071
Command Modes ROUTER OSPF Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1072
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.
PAGE 1073
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ● show ip ospf asbr — display the VLAN configuration. distance Define an administrative distance for particular routes to a specific IP address.
PAGE 1074
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. distance ospf Configure an OSPF distance metric for different types of routes. Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command.
PAGE 1075
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. To specify a distance for routes learned from other routing domains, use the redistribute command. distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table.
PAGE 1076
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1077
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1078
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on all platforms. The higher this parameter is set, the faster OSPF converge takes place.
PAGE 1079
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Added support for Multi-Process OSPF. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The Helper mode is enabled by default on the device.
PAGE 1080
Version Description 8.3.12.0 Introduced on the S4810. 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart mode Enable the graceful restart mode.
PAGE 1081
graceful-restart role Specify the role for your OSPF router during graceful restart. Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command. Parameters Defaults role helper-only (OPTIONAL) Enter the keywords helper-only to specify the OSPF router is a helper only during graceful restart. role restart-only (OPTIONAL) Enter the keywords restart-only to specify the OSPF router is a restart only during graceful-restart.
PAGE 1082
Parameters Defaults seconds Enter the seconds. The range is from 0 to 300. zero (0) seconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1083
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1084
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. If this command is not configured, cost is based on the auto-cost command.
PAGE 1085
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information By default, the dead interval is four times the default hello-interval. Related Commands ● ip ospf hello-interval — set the time interval between the hello packets. ip ospf hello-interval Specify the time interval between the hello packets sent on the interface.
PAGE 1086
Version Description pre- 6.1.1.1 Introduced on the E-Series. Usage Information The time interval between the hello packets must be the same for routers in a network. Related Commands ● ip ospf dead-interval — set the time interval before a router is declared dead. ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command.
PAGE 1087
To change to a different key on the interface, enable the new key while the old key is still enabled. Dell EMC Networking OS sends two packets: the first packet authenticated with the old key and the second packet authenticated with the new key. This process ensures that the neighbors learn the new key and communication is not disrupted by keeping the old key enabled. After the reply is received and the new key is authenticated, delete the old key. Dell EMC recommends keeping only one key per interface.
PAGE 1088
To return to the default, use the no ip ospf network command. Parameters Defaults broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-to-point network. Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1089
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1090
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1091
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1092
Version Description pre- 6.1.1.1 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths.
PAGE 1093
mib-binding Enable this OSPF process ID to manage the SNMP traps and process SNMP queries. Syntax mib-binding To mib-binding on this OSPF process, use the no mib-binding command. Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command.
PAGE 1094
NOTE: If the area ID is smaller than 65535, it is converted to a decimal value. For example, if you use an area ID of 0.0.0.1, it is converted to 1. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1095
Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive. interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information.
PAGE 1096
passive-interface interface ● The previous no passive-interface interface is removed from the running configuration. ● The ABR status for the router is updated. ● Save passive-interface interface into the running configuration. passive-interface default ● All present and future OSPF interfaces are marked as passive. ● Any adjacency is explicitly terminated from all OSPF interfaces. ● All previous passive-interface interface commands are removed from the running configuration.
PAGE 1097
Defaults Not configured. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1098
route-map map- name tag tag-value Defaults (OPTIONAL) Enter the keywords route-map then the name of the route map. (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. None Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1099
level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- value (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
PAGE 1100
Defaults None. Command Modes ROUTER OSPF Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1101
vrf name Defaults (Optional) Enter the VRF process identifier to tie the OSPF instance to the VRF. All network commands under this OSPF instance are then tied to the VRF instance. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1102
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1103
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.
PAGE 1104
Area ranges are DellEMC# show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. Syntax show ip ospf [process-id | vrf vrf-name] asbr Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1105
You can determine if an ASBR is in a directly connected area (or not) by the flags. For ASBRs in a directly connected area, E flags are set. In the following example, router 1.1.1.1 is in a directly connected area since the Flag is E/-/-/. For remote ASBRs, the E flag is clear (-/-/-/). Example DellEMC# show ip ospf 1asbr RouterID 3.3.3.3 1.1.1.1 DellEMC# Flags -/-/-/ E/-/-/ Cost Nexthop 2 10.0.0.2 0 0.0.0.0 Interface Area Tf 1/1 1 0 show ip ospf database Display all LSA information.
PAGE 1106
Usage Information Example Version Description 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database command shown in the following example. Field Description Link ID Identifies the router ID. ADV Router Identifies the advertising router’s ID. Age Displays the link state age. Seq# Identifies the link state sequence number. This number allows you to identify old or duplicate link state advertisements.
PAGE 1107
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: ● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.
PAGE 1108
Field Description ● E or No E is displayed on whether the originating router can accept AS External LSAs. Example LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the advertising router’s ID. Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the Type of Service (TOS) options.
PAGE 1109
link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: ● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ip- address (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router.
PAGE 1110
Example Field Description LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. LS Seq Number Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area.
PAGE 1111
show ip ospf database network Display the network (type 2) LSA information. Syntax Parameters show ip ospf [process-id] database network [link-state-id] [adv-router ipaddress] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1112
Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: ● TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service. ● DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. ● E or No E is displayed on whether the originating router can accept AS External LSAs.
PAGE 1113
show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database nssa-external [linkstate-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1114
● show ip ospf database — display OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information. Syntax show ip ospf [process-id | vrf vrf-name ] database opaque-area [link-stateid] [adv-router ip-address] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1115
Usage Information Version Description pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database opaque-area command shown in the following example. Item Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: ● TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1116
show ip ospf database opaque-as Display the opaque-as (type 11) LSA information. Syntax show ip ospf process-id database opaque-as [link-state-id] [adv-router ipaddress] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1117
show ip ospf database opaque-link Display the opaque-link (type 9) LSA information. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database opaque-link [link-stateid] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1118
show ip ospf database router Display the router (type 1) LSA information. Syntax show ip ospf [process-id | vrf vrf-name ] database router [link-state-id] [adv-router ip-address] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view the router LSA information corresponding to the OSPF process that is tied to a specific VRF.
PAGE 1119
Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: ● TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service. ● DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. ● E or No E is displayed on whether the originating router can accept AS External LSAs.
PAGE 1120
Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.142.2 (Link Data) Router Interface address: 192.68.142.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.141.2 (Link Data) Router Interface address: 192.68.141.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.140.2 (Link Data) Router Interface address: 192.68.140.
PAGE 1121
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.
PAGE 1122
LS age: 1551 Options: (No TOS-capability, DC, E) LS type: Summary Network Link State ID: 192.68.16.0 Advertising Router: 192.168.17.1 LS Seq Number: 0x80000054 Checksum: 0xb5a2 Length: 28 Network Mask: /24 TOS: 0 Metric: 1 LS age: 9 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.32.0 Advertising Router: 1.1.1.
PAGE 1123
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1124
Item Description Backup Designated... This line displays the ID of the Backup Designated Router and its interface address. Timer intervals... This line displays the interface’s timer settings for Hello interval, Dead interval, Transmit Delay (Wait), and Retransmit Interval. Example Hello due... This line displays the amount time until the next Hello packet is sent out this interface. Neighbor Count... This line displays the number of neighbors and adjacent neighbors.
PAGE 1125
Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1126
show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Syntax show ip ospf [process-id | vrf vrf-name ] routes Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show the OSPF RIB information corresponding to the OSPF processes that are tied to a specific VRF.
PAGE 1127
Version 9.4(0.0), the show ip ospf routes command displays the interface and area ID information of connected networks in addition to the other settings, whereas these details are not displayed until Dell EMC Networking OS Version 9.3(0.0). Starting with Version 9.4(0.0), the metric of E2 routes in the output is displayed as an external metric, whereas until Dell EMC Networking OS Version 9.3(0.0), the number of hops to the ASBR for E2 routes are displayed in the output.
PAGE 1128
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1129
Example Error Type Description Intf_Down Received packets on an interface that is either down or OSPF is not enabled. Non-Dr Received packets with a destination address of ALL_DRS even though SELF is not a designated router. Self-Org Receive the self originated packet. Wrong_Len The received packet length is different to what was indicated in the OSPF header. Invld-Nbr LSA, LSR, LSU, and DDB are received from a peer which is not a neighbor peer.
PAGE 1130
● ● ● ● ● Example (Statistics) The packet count received and transmitted for each neighbor Dead timer remaining value for each neighbor Transmit timer remaining value for each neighbor The LSU Q length and its highest mark for each neighbor The LSR Q length and its highest mark for each neighbor DellEMC(conf-if-tf-1/6)# do show ip ospf statistics Interface twentyFiveGigE 1/6 Error packets (Receive statistics) Intf-Down 0 Non-Dr 0 Self-Org 0 Wrong-Len 0 Invld-Nbr 0 Nbr-State 0 Auth-Error 0 MD5-Error 0 Cksum
PAGE 1131
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. DellEMC# show ip ospf 10 timers rate-limit List of LSAs in rate limit Queue LSA id: 1.1.1.0 Type: 3 Adv Rtid: 3.3.3.3 Expiry time: 00:00:09.111 LSA id: 3.3.3.3 Type: 1 Adv Rtid: 3.3.3.
PAGE 1132
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. To isolate problems with inter-area and external routes, use this command. In OSPF inter-area and external routes are calculated by adding LSA cost to the cost of reaching the router.
PAGE 1133
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1134
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1135
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1136
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. OSPFv3 Commands Open shortest path first version 3 (OSPFv3) for IPv6 is supported on the platform.
PAGE 1137
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1138
key-encryptionalgorithm key (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in encryption. The required lengths of a non-encrypted or encrypted key are: 3DES - 48 or 96 hex digits; DES - 16 or 32 hex digits; AES-CBC -32 or 64 hex digits for AES-128 and 48 or 96 hex digits for AES-192. authenticationalgorithm key-encryptiontype key Specifies the authentication algorithm to use for encryption. Valid values are MD5 or SHA1.
PAGE 1139
The configuration of IPsec encryption on an interface-level takes precedence over an area-level configuration. If you remove an interface configuration, an area encryption policy that has been configured is applied to the interface. To remove an IPsec encryption policy from an interface, enter the no area area-id encryption spi number command. Related Commands ● ipv6 ospf encryption – configure an IPsec encryption policy on an OSPFv3 interface.
PAGE 1140
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.9(0.
PAGE 1141
Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. debug ipv6 ospf bfd Display debug information and interface types for bidirectional forwarding detection (BFD) on OSPF IPv6 packets.
PAGE 1142
Usage Information Example The following section describes the command fields. Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1143
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. vrf vrf-name Enter the keyword vrf to view debugging information on OSPF corresponding to that VRF. detail Enter the keyword detail to view detailed debugging information. Command Modes EXEC Privilege Command History Example Example (detail) This guide is platform-specific.
PAGE 1144
Command Fields Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version.. type: Displays the type of packet sent: ● ● ● ● ● 1 - Hello packet 2 - database description 3 - link state request 4 - link state update 5 - link state acknowledgement Length: Displays the OSPFv3 packet length. Router ID: Displays the OSPFv3 router ID. Area ID: Displays the OSPFv3 area ID.
PAGE 1145
Usage Information Example The following section describes the command fields. Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1146
route-map map- name Defaults (OPTIONAL) Enter the keywords route-map then the name of an established route map. Disabled. Command Modes ROUTER OSPFv3 Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1147
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1148
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. OSPFv3 graceful restart supports planned-only and/or unplanned-only restarts. The default is support for both planned and unplanned restarts.
PAGE 1149
Version Description 7.4.1.0 Introduced on the E-Series and C-Series. ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface. Syntax Parameters ipv6 ospf authentication {null | ipsec spi number {MD5 | SHA1} [keyencryption-type] key}} null Causes an authentication policy configured for the area to not be inherited on the interface. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy.
PAGE 1150
To remove an IPsec authentication policy from an interface, enter the no ipv6 ospf authentication spi number command. To remove null authentication on an interface to allow the interface to inherit the authentication policy configured for the OSPFv3 area, enter the no ipv6 ospf authentication null command. ipv6 ospf cost Explicitly specify the cost of sending a packet on an interface.
PAGE 1151
ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down. Syntax ipv6 ospf dead-interval seconds To return to the default time interval, use the no ipv6 ospf dead-interval command. Parameters Defaults seconds Enter the time interval in seconds. The range is from 1 to 65535 seconds. 40 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1152
esp encryption- algorithm Encryption algorithm used with ESP. Valid values are: 3DES, DES, AES-CBC, and NULL. For AES-CBC, only the AES-128 and AES-192 ciphers are supported. key-encryptiontype key (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication.
PAGE 1153
authentication policy configured for the OSPFv3 area, enter the no ipv6 ospf no ipv6 ospf encryption null command. ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured.
PAGE 1154
Defaults 10 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1155
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. Setting a priority of 0 makes the router ineligible for election as a Designated Router or Backup Designated Router.
PAGE 1156
Version Description 7.4.1.0 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range is from 1 to 64. The default is 8 paths. 8 Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1157
To remove the maximum metric assignment from an OSPF router and send LSAs with the currently configured cost, enter no max-metric router-lsa [on-startup {announce-time | wait-for-bgp [waittime]}]. Parameters on-startup announce-time Enter the time (in seconds) following boot-up during which the maximum cost (65535) for transmitting OSPF traffic on router interfaces is announced in LSAs and the router functions as a stub router. Range: 5 to 86400 seconds.
PAGE 1158
Time remaining 00:07:07 Condition : On-Startup while BGP is converging for 600 secs.
PAGE 1159
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.
PAGE 1160
● 1 for a type 1 external route ● 2 for a type 2 external route The default is 2. route-map map- name tag tag-value (OPTIONAL) Enter the keywords route-map then the name of an established route map. If the route map is not configured, the default is deny (to drop all routes). (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPFv3. The range is from 0 to 4294967295 The default is 0. Defaults Not configured.
PAGE 1161
ROUTER OSPFv3 for OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1162
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. The show crypto ipsec policy command output displays the AH and ESP parameters configured in IPsec security policies, including the SPI number, keys, and algorithms used.
PAGE 1163
Field Description Inbound ESP Auth Key and Outbound Auth Key The ESP authentication key for inbound and outbound links. Inbound ESP Cipher Key and Outbound ESP Cipher Key The ESP encryption key for inbound and outbound links. Transform set The set of security protocols and algorithms used in the policy. Inbound AH SPI The authentication header (AH) security policy index (SPI) for inbound and outbound links. and Outbound AH SPI Inbound AH Key The AH key for inbound and outbound links.
PAGE 1164
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1165
replay detection support : N STATUS : ACTIVE show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/ outbound ah Authentication policy applied to inbound or outbound traffic. inbound/ outbound esp Encryption policy applied to inbound or outbound traffic. spi Security policy index number used to identify the policy.
PAGE 1166
Defaults network (OPTIONAL): Enter the keyword network to display the network link states. nssa-external (OPTIONAL): Enter the keyword nssa-external to display the nssa link state information. router (OPTIONAL): Enter the keyword router to display the router link states. None Command Modes EXEC EXEC Privilege Command History Usage Information Example (gracelsa) This guide is platform-specific.
PAGE 1167
Process 1 database summary Type Count/Status Oper Status 1 Admin Status 1 Area Bdr Rtr Status 1 AS Bdr Rtr Status 1 AS Scope LSA Count 0 AS Scope LSA Cksum sum 0 Originate New LSAS 50 Rx New LSAS 22 Ext LSA Count 0 Rte Max Eq Cost Paths 10 GR grace-period 180 GR mode planned and unplanned Area 0 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 6 Rtr LSA Count 2 Net LSA Count 1 Inter Area Pfx LSA Count 1 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra
PAGE 1168
AS External Link States (Area 1) LS Age: 35 LS Type: OSPFv3 NSSA LSA Link State ID: 0.0.0.1 Advertising Router: 1.1.1.1 LS Seq Number: 0x80000001 Checksum: 0xD2DD Length: 52 Prefix: 101:101:1::/64 Prefix Options: 0x8 ( P ) Metric Type: 2 Metric: 20 Forwarding Address: 101:101:1::1 show ipv6 ospf interface View OSPFv3 interface information. Syntax show ipv6 ospf [process-number] [vrf vrf-name] [interface] Parameters process-number Enter the OSPF process number.
PAGE 1169
Usage Information Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Added support for showing BFD status on the S4820T, S4810, and Z9000. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.
PAGE 1170
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults None Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1171
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6010–ON, S6100–ON, Z9100–ON, Z9500, S6000–ON, C9010, MXL, and FN IOM. Use SNMPv3 context configuration to distinguish between various OSPFv3 VRF instances.
PAGE 1172
Usage Information Example 1172 Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S6000-ON, S6000, S4820T, S4810, S5000. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage.
PAGE 1173
39 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1174
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.7.1.0 Introduced on the E-Series. You can apply any number of redirect-groups to an interface. A redirect list can contain any number of configured rules.
PAGE 1175
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.
PAGE 1176
● ● ● ● ● ● operator = = = = = = acknowledgement finish (no more data from the user) push function reset the connection synchronize sequence number urgent field (OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand: ● ● ● ● ● Defaults ack fin psh rst syn urg eq = equal to neq = not equal to gt = greater than lt= less than range = inclusive range of ports (you must specify two ports for the portcommand parameter.
PAGE 1177
● You can also use the no redirect {ip-address | slot/port}| tunnel tunnel-id} [track ] {ip-protocol-number [bit] | protocol-type} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator] command. Parameters redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the IP address of the forwarding router. slot/port Enter the keyword slot / port followed by the slot/port information.
PAGE 1178
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, and Z9000. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 1179
● udp for user datagram protocol source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1180
Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. show cam pbr Display the PBR CAM content. Syntax show cam pbr {interface interface | stack—unit slot-number port-set number [pipeline number]} [summary] Parameters interface interface stack–unit number Defaults Enter the keyword interface then the name of the interface. Enter the keyword stack-unit then the slot number.
PAGE 1181
show ip redirect-list View the redirect list configuration and the interfaces it is applied to. Syntax Parameters show ip redirect-list redirect-list-name redirect-listname Enter the name of a configured Redirect list. Command Modes ● EXEC ● EXEC Privilege Command History Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1182
40 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • IPv4 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement.
PAGE 1183
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1184
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
PAGE 1185
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface.
PAGE 1186
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1187
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 6.1.1.0 Added support for the VLAN interface. ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number.
PAGE 1188
ip pim join-filter Permit or deny PIM Join/Prune messages on an interface using an extended IP access list. This command prevents the PIM-SM router from creating state based on multicast source and/or group. Syntax ip pim join-filter ext-access-list [in | out] To remove the access list, use the no ip pim join-filter ext-access-list command. Parameters Defaults ext-access-list Enter the name of an extended access list.
PAGE 1189
ip pim neighbor-filter To prevent a router from participating in protocol independent multicast (PIM), configure this feature. Syntax ip pim [vrf vrf-name] neighbor-filter {access-list} To remove the restriction, use the no ip pim [vrf vrf-name] neighbor-filter {accesslist} command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to prevent that VRF from participating in PIM. NOTE: Applies to specific VRF if input is provided, else applies to default VRF.
PAGE 1190
Parameters Defaults seconds Enter a number as the number of seconds between router query messages. The range is from 0 to 65535. The default is 30 seconds. 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1191
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.
PAGE 1192
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.
PAGE 1193
● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults priority (OPTIONAL) Enter the priority used in Bootstrap election process. The range is zero (0) to 255. The default is 192. acl-name (OPTIONAL) Enter the name of an ACL to configure a PIM router to act as an RP for a specific set of multicast group addresses that are defined in the ACL. Not configured.
PAGE 1194
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1195
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Removed the acl-access-list parameter. Modified the max value of S, G entry second range from 86400 to 65535. Introduced on the S6000ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1196
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.7(0.0) Added support for VRF. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1197
infinity Defaults (OPTIONAL) Enter the keyword infinity to never switch to the source-tree. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1198
Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1199
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim interface command shown in the following example.
PAGE 1200
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1201
show ip pim rp View all multicast groups-to-RP mappings. Syntax Parameters show ip pim [vrf vrf-name] rp [mapping | group-address] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. mapping (OPTIONAL) Enter the keyword mapping to display the multicast groups-to-RP mapping and information on how RP is learnt. group-address (OPTIONAL) Enter the multicast group address mask in dotted decimal format to view RP for a specific group.
PAGE 1202
Group(s): 224.0.0.0/4, Static RP: 50.40.4.4, v2 DellEMC# Example (Address) DellEMC# show ip pim rp 229.1.2.1 Group RP 229.1.2.1 165.87.20.4 DellEMC# show ip pim ssm-range Display the non-default groups added using the SSM range feature. Syntax show ip pim [vrf vrf-name] ssm-range Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 1203
show ip pim summary View information about PIM-SM operation. Syntax Parameters show ip pim [vrf vrf-name] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1204
0 0 0 0 PIM nexthops RPs sources Register states Message summary: 2582/2583 Joins sent/received 5/0 Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 State-Refresh messages sent/received 0/0 MSDP updates sent/received 0/0 Null Register messages sent/received 0/0 Register-stop messages sent/received Data path event summary: 0 no-cache messages received 0 last-hop switchover messages received 0/0 pim-assert messages sent/received 0/0 register messages sent
PAGE 1205
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim tib command shown in the following example. Field Description (S, G) Displays the entry in the multicast PIM database. uptime Displays the amount of time the entry has been in the PIM route table.
PAGE 1206
Vlan 2006 Forward/Sparse 00:06:21/Never (*, 225.1.1.2), uptime 00:40:15, expires 00:00:00, RP 20.40.4.4, flags: SCJ Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (20.10.4.9, 225.1.1.2), uptime 00:06:21, expires 00:02:06, flags: CT Incoming interface: Vlan 2007, RPF neighbor 20.30.124.
PAGE 1207
41 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1208
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.
PAGE 1209
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced GRE protocol support. ip access-group Assign an IP access list (IP ACL) in the monitor session mode. Syntax Parameters Defaults ip access-group access-list-name access-list-name Enter the name of a configured access list, up to 140 characters. Not enabled. Command Modes MONITOR SESSION Command History This guide is platform-specific.
PAGE 1210
Enable status: Disabled Command Modes CONFIGURATION Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1211
Defaults ttl_value IP TTL value of the ERSPAN traffic. The range is from 1 to 255. The default value is 255. drop Monitors only the dropped packets in the Ingress. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1212
Parameters Defaults limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. 60 Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1213
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC(conf-mon-sess-1)# show config ! monitor session 1 source twentyFiveGigE 1/1 destination Port-channel 1 direction rx show monitor session Display information about monitoring sessions.
PAGE 1214
Example Version Description 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1215
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1216
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094.
PAGE 1217
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the any parameter. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.
PAGE 1218
42 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1219
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1220
private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN.
PAGE 1221
private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input.
PAGE 1222
To remove PVLAN mode from the selected port, use the no switchport mode private-vlan command. Parameters Defaults host Enter the keyword host to configure the selected port or port channel as an isolated interface in a PVLAN. promiscuous Enter the keyword promiscuous to configure the selected port or port channel as an promiscuous interface. trunk Enter the keyword trunk to configure the selected port or port channel as a trunk port in a PVLAN. Disabled.
PAGE 1223
43 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1224
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Syntax disable To enable PVST+, use the no disable command. Defaults Disabled.
PAGE 1225
Related Commands ● protocol spanning-tree pvst — enter PVST+ mode. extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
PAGE 1226
Tf 1/10 Desg 128.140 128 Tf 1/12 Dis 128.142 128 DellEMC(conf-pvst)# Related Commands 200000 FWD 0 200000 DIS 0 P2P P2P No No ● protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History Example 1226 This guide is platform-specific.
PAGE 1227
Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands ● disable — disables PVST+. ● show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. Syntax Parameters show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094.
PAGE 1228
Usage Information Example (Brief) Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.
PAGE 1229
Number of topology changes 3, last change occured 00:57:00 Port 130 (twentyFiveGigE 1/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.130 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1230
Example (Guard) Related Commands DellEMC# show spanning-tree pvst vlan 5 guard Interface Name Instance Sts Guard type ----------------------------------Tf 1/1 5 INCON(Root) Rootguard Tf 1/2 5 FWD Loopguard Tf 1/3 5 EDS(Shut) Bpduguard DellEMC# ● spanning-tree pvst — configure PVST+ on an interface.
PAGE 1231
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1232
● If no BPDU is received from a remote device, loop guard places the port in a Loop-Inconsistent Blocking state and no traffic is forwarded on the port. Example DellEMC(conf-if-tf-1/1)# spanning-tree pvst vlan 3 cost 1800 DellEMC(conf-if-tf-1/1)# end DellEMC(conf-if-tf-1/1)# show config ! interface twentyFiveGigE 1/1 no ip address switchport spanning-tree pvst vlan 3 cost 18000 no shutdown DellEMC(conf-if-tf-1/1)# end DellEMC# Related Commands ● show spanning-tree pvst — views the PVST+ configuration.
PAGE 1233
Dell EMC Networking systems do not expect PVST+ BPDU on an untagged port. If this happens, Dell EMC Networking OS places the port in the Error-Disable state. This behavior might result in the network not converging. To prevent Dell EMC Networking OS from executing this action, use the no spanningtree pvst err-disable command cause invalid-pvst-bpdu. Related Commands ● show spanning-tree pvst — views the PVST+ configuration.
PAGE 1234
vlan bridge-priority Set the PVST+ bridge-priority for a VLAN or a set of VLANs. Syntax vlan vlan-range bridge-priority value To return to the default value, use the no vlan bridge-priority command. Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. bridge-priority Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768.
PAGE 1235
vlan forward-delay Set the amount of time the interface waits in the Listening state and the Learning state before transitioning to the Forwarding state. Syntax vlan vlan-range forward-delay seconds To return to the default setting, use the no vlan forward-delay command. Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094.
PAGE 1236
vlan hello-time Set the time interval between generation of PVST+ 7 BPDUs. Syntax vlan vlan-range hello-time seconds To return to the default value, use the no vlan hello-time command. Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. hello-time Enter the keywords hello-time then the time interval, in seconds, between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds.
PAGE 1237
vlan max-age To maintain configuration information before refreshing that information, set the time interval for the PVST+ bridge. Syntax vlan vlan-range max-age seconds To return to the default, use the no vlan max-age command. Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. max-age seconds Enter the keywords max-age then the time interval, in seconds, that Dell EMC Networking OS waits before refreshing configuration information.
PAGE 1238
44 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1239
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. service-class bandwidth-percentage Specify a minimum bandwidth for queues.
PAGE 1240
service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. Syntax service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} Parameters Defaults queue Enter a value from 0 to 7. For each dot1p Priority, the default CoS queue value is: ● Dot1p Priority : 0 1 2 3 4 5 6 7 ● Queue : 1 0 2 3 4 5 6 7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1241
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1242
Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives. Syntax dot1p-priority priority-value To delete the IEEE 802.1p configuration on the interface, use the no dot1p-priority command. Defaults none Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1243
Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). The range is from 0 to 40000000100000000. The default granularity is Megabits per second (Mbps). committed-rate Enter the bandwidth in Mbps. The range is from 0 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB. The range is from 16 to 200000. The default is 50. peak peak-rate (OPTIONAL) Enter the keyword peak then a number to specify the peak rate in Mbps. The range is from 0 to 40000.
PAGE 1244
rate-shape Shape the traffic output on the selected interface. Syntax rate shape [kbps] rate [burst-KB] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000100000000. The default granularity is Megabits per second (Mbps). rate The range is from 10 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB. The range is from 0 to 10000. The default is 50.
PAGE 1245
service-class dynamic dot1p Honor all 802.1p markings on incoming switched traffic on an interface (from INTERFACE mode) or on all interfaces (from CONFIGURATION mode). A CONFIGURATION mode entry supersedes an INTERFACE mode entry. Syntax service-class dynamic dot1p To return to the default setting, use the no service-class dynamic dot1p command. Defaults All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command.
PAGE 1246
Usage Information Version Description 6.1.1.1 Introduced on the E-Series. To honor all incoming 802.1p markings on incoming switched traffic on the interface, enter this command. By default, this facility is not enabled (that is, the 802.1p markings on incoming traffic are not honored). You can apply this command on both physical interfaces and port channels.
PAGE 1247
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced on the E-Series. Usage Information The unit of bandwidth percentage is 1%. If the sum of the bandwidth percentages given to all eight classes exceeds 100%, the bandwidth percentage automatically scales down to 100%. Related Commands ● qos-policy-output — creates a QoS output policy.
PAGE 1248
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-of-service policies to each class. Syntax class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] Parameters Defaults match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
PAGE 1249
Related Commands ● ● ● ● ● ● ● ● ● ● ip access-list extended — configures an extended IP ACL. ip access-list standard — configures a standard IP ACL. match ip access-group — configures the match criteria based on the access control list (ACL). match ip precedence — identifies the IP precedence values as match criteria. match ip dscp — configures the match criteria based on the DSCP value. match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL.
PAGE 1250
Related Commands Version Description 8.3.18.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. ● show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1251
● qos-policy-input — creates an input QoS-policy on the router. ● qos-policy-output — creates an output QoS-policy on the router. ● wred-profile — creates a WRED profile. match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IP-any class-maps on both ACLs as well as VLANs.
PAGE 1252
Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series; added support for the DSCP Marking option. 6.1.1.1 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed.
PAGE 1253
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the keyword multicast ; added the DSCP Marking option support on the S-Series. 7.6.1.
PAGE 1254
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1255
Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1256
Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1257
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced. Usage Information To access this command, enter the class-map command.
PAGE 1258
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information An aggregate output QoS policy applies to all outbound port traffic. An aggregate output QoS policy can coexist with per-queue output QoS policies.
PAGE 1259
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series.
PAGE 1260
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map.
PAGE 1261
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined.
PAGE 1262
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rateshape, scheduler strict, bandwidth-percentage, and WRED can be defined.
PAGE 1263
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information The default burst size is 100Kb. If a different value is required, you must configure the burst size to the required value.
PAGE 1264
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information On 40-port 10G stack-unit if the traffic is shaped between 64 and 1000 Kbs, for some values, the shaped rate is much less than the value configured.
PAGE 1265
Usage Information If there is no option to create a new rule and to avoid reconfiguring class-map, use the resequence class-map command. This allows you to create numbering spaces. service-policy input Apply an input policy map to the selected interface. Syntax service-policy input policy-map-name [layer2] To remove the input policy map from the interface, use the no service-policy input policymap-name [layer2] command.
PAGE 1266
(without the policy-map-name option) and the service-class dynamic dot1p command are allowed on an interface. Related Commands ● policy-map-input — creates an input policy map. service-policy output Apply an output policy map to the selected interface. Syntax service-policy output policy-map-name To remove the output policy map from the interface, use the no service-policy output policy-map-name command.
PAGE 1267
service-queue Assign a class map and QoS policy to different queues. Syntax service-queue queue-id [class-map class-map-name] [qos-policy qos-policyname] To remove the queue assignment, use the no service-queue queue-id [class-map classmap-name] [qos-policy qos-policy-name] command. Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7.
PAGE 1268
● service-policy output — applies an output policy map to the selected interface. set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. Syntax set {ip-dscp value | mac-dot1p value} Parameters Defaults ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63. mac-dot1p value Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7.
PAGE 1269
Parameters Defaults class-name (Optional) Enter the name of a configured class map. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced the seq option on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1270
summary interface To view a policy map interface summary, enter the keyword summary and optionally one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information.
PAGE 1271
Example (IPv4) Version Description 7.4.1.0 E-Series only: Added trust IPv6 diffserv . 6.2.1.1 Introduced on the E-Series.
PAGE 1272
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1273
show qos policy-map-output View the output QoS policy map details. Syntax Parameters show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] policy-map-name Enter the policy map name. qos-policyoutput qos- Enter the keyword qos-policy-output then the QoS policy name. policy-name Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1274
show qos qos-policy-input View the input QoS policy details. Syntax show qos qos-policy-input [qos-policy-name] Parameters Defaults qos-policy-name Enter the QoS policy name. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1275
Parameters Defaults qos-policy-name Enter the QoS policy name. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1276
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/ subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/ subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information.
PAGE 1277
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.1 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1278
Parameters Defaults wred-ecn Enter the keyword wred-ecn to display the details of ECN marked packets. interface Slot/ Port[/Subport] Enter an interface to display the details of ECN marked packets specific to the interface. none Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 1279
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.
PAGE 1280
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.9(0.0) Introduced on the Z9500, S4810, S4820T, S5000, and S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.
PAGE 1281
stackunit number (OPTIONAL) Enter the keyword stack-unit then the stack-unit slot number. port-set portpipe Enter the keywords port-set then the stack-unit port pipe number. The range is number from 0 or 1. stack-unit all Defaults (OPTIONAL) Enter the keywords stack-unit all to indicate all stack-unit. none Command Modes EXEC Command History Usage Information This guide is platform-specific.
PAGE 1282
Field Description Status (Allowed ports) Indicates if the input policy map configuration on an interface belonging to a stackunit/port-pipe is successful — Allowed (n) — or not successful — Exception. The allowed number (n) indicates the number of ports in that port-pipe on which the Policy Map can be applied successfully. NOTE: In a Layer 2 Policy Map, IPv4/IPv6 rules are not allowed; therefore, the output contains only L2ACL CAM partition entries.
PAGE 1283
threshold Specify the minimum and maximum threshold values for the configured WRED profiles. Syntax threshold min number max number max-drop-drop To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360. max number Enter the keyword max then the maximum threshold number for the WRED profile. The range is from 1 to 9360 KB.
PAGE 1284
trust Specify dynamic classification (DSCP) or dot1p to trust. Syntax trust {diffserv [fallback]| dot1p [fallback]} Parameters Defaults diffserv Enter the keyword diffserv to specify trust of DSCP markings. dot1p Enter the keyword dot1p to specify trust dot1p configuration. fallback Enter the keyword fallback to classify packets according to their DSCP or dot1p value as a secondary option in case no match occurs against the configured class maps.
PAGE 1285
Table 6.
PAGE 1286
Parameters yellow | green Enter the keyword yellow for yellow traffic. A DSCP value of xxx110 and xxx100, xxx101 maps to yellow. Enter the keyword green for green traffic. A DSCP value of xxx0xx are green and DSCP 111111 are red packets. profile-name Enter your WRED profile name in character format (32 character maximum). Or use one of the five pre-defined WRED profile names. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_.
PAGE 1287
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1288
Command Modes QOS-POLICY-OUT mode Command History Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3.0.0 Introduced on the S6000 and Z9000 platforms If the average queue size is more than the maximum threshold of WRED, the packet is dropped.
PAGE 1289
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. Usage Information Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred).
PAGE 1290
pps. The range is from 0 to 40000 for Mbps (which is the default measure for rate limits if you do not explicitly configure Kbps or pps) Default burst-KB (OPTIONAL) Enter the peak burst size in KB. The range is from 0 to 10000. The default is 50 KB. Packets (OPTIONAL) Enter the peak burst size as a count of packets. The range is from 1 to 1073000. The default is 50 packets. The default peak rate is regarded as the same value as the configured peak rate.
PAGE 1291
can enable WRED and ECN configuration on the global service-pools. You can define WRED profiles and weight on each of the global service-pools for both lossy and lossless (PFC) service-pools. Syntax Parameters Default [No] service-pool wred {green | weight | yellow} {pool0 number/string| pool1 number/string}pool0 number/string service-pool Define the mapping between the service class and policy-based QoS or routing. wred Specify WRED curve parameters for a queue.
PAGE 1292
DellEMC(conf) #service-pool wred yellow pool0 thresh-3 pool1 thresh-4 DellEMC(conf) #service-pool wred weight pool0 11 pool1 4 DellEMC(conf-wred) #wred thresh-1 DellEMC(conf-wred) #threshold min 100 max 200 max-drop-rate 40 DellEMC(conf-wred) #wred thresh-2 DellEMC(conf-wred) #threshold min 300 max 400 max-drop-rate 80 DellEMC(conf) #service-pool wred green pool0 thresh-1 pool1 thresh-2 DellEMC(conf) #service-pool wred yellow pool0 thresh-3 pool1 thresh-4 DellEMC(conf) #service-pool wred weight pool0 11 poo
PAGE 1293
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. If the specified color-map does not exist, the Diffserv Manager (DSM) creates a color map and sets all the DSCP values to green (low drop precedence).
PAGE 1294
Version Description 9.5(0.1) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information A color map outlines the codepoint mappings to the appropriate color mapping (green, yellow, red) for the traffic. The system uses this information use to handle the traffic on the interface based on the traffic priority and places it into the appropriate shaping queue.
PAGE 1295
Example The following example assigns the color map, bat-enclave-map, to interfacetw 1/1. DellEMC(conf)# int tw 1/1 DellEMC(conf-if-tf-1/1)# qos dscp-color-policy bat-enclave-map DellEMC(conf-if-tf-1/1)# Related Commands ● dscp— sets the number of specific DSCP values for color map profile to yellow or red. ● qos dscp-color-map— configures the DSCP color map. show qos dscp-color-policy Display DSCP color policy configuration for one or all interfaces.
PAGE 1296
DellEMC# show qos dscp-color-policy detail tw 1/10 Interface twentyFiveGigE 1/10 Dscp-color-map mapONE yellow 4,7 red 20,30 Related Commands ● show qos dscp-color-map — displays DSCP color maps. show qos dscp-color-map Display the DSCP color map for one or all interfaces. Syntax show qos dscp-color-map map-name Parameters Defaults map-name Enter the name of the color map. None Command Modes EXEC Command History Example This guide is platform-specific.
PAGE 1297
45 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1298
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1299
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1300
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1301
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The default route must be present in the switch routing table for the default-information originate command to take effect.
PAGE 1302
Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information This command ensures that route information being redistributed is converted to the same metric value. Related Commands ● redistribute — allows you to redistribute routes learned by other methods. description Enter a description of the RIP routing protocol.
PAGE 1303
distance Assign a weight (for prioritization) to all routes in the RIP routing table or to a specific route. Lower weights (“administrative distance”) are preferred. Syntax distance weight [ip-address mask [prefix-name]] To return to the default values, use the no distance weight [ip-address mask] command. Parameters Defaults weight Enter a number from 1 to 255 for the weight (for prioritization). The default is 120. ip-address (OPTIONAL) Enter the IP address, in dotted decimal format (A.B.C.
PAGE 1304
distribute-list in Configure a filter for incoming routing updates. Syntax distribute-list prefix-list-name in [interface] To delete the filter, use the no distribute-list prefix-list-name in command. Parameters prefix-list-name Enter the name of a configured prefix list. interface (OPTIONAL) Identifies the interface type slot/port as one of the following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 1305
Related Commands Version Description pre- 6.2.1.1 Introduced on the E-Series. ● ip prefix-list — enters PREFIX-LIST mode and configures a prefix list. distribute-list out Configure a filter for outgoing routing updates. Syntax distribute-list prefix-list-name out [interface | bgp | connected | isis | ospf | static] To delete the filter, use the no distribute-list prefix-list-name out command. Parameters prefix-list-name Enter the name of a configured prefix list.
PAGE 1306
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.
PAGE 1307
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ● ip split-horizon — sets the RIP routing updates to exclude routing prefixes. ip rip receive version To receive specific versions of RIP, set the interface. The RIP version you set on the interface overrides the version command in ROUTER RIP mode.
PAGE 1308
Usage Information If you want the interface to receive both versions of RIP, use the ip rip receive version 1 2 command. Related Commands ● ip rip send version — sets the RIP version for sending RIP traffic on an interface. ● version — sets the RIP version the switch software uses. ip rip send version To send a specific version of RIP, set the interface. The version you set on the interface overrides the version command in ROUTER RIP mode.
PAGE 1309
ip split-horizon Enable split-horizon for RIP data on the interface. As described in RFC 2453, the split-horizon scheme prevents any routes learned over a specific interface to be sent back out that interface. Syntax ip split-horizon To disable split-horizon, use the no ip split-horizon command. Defaults Enabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 1310
Command Modes ROUTER RIP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1311
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1312
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. You can enable an unlimited number of RIP networks.
PAGE 1313
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1314
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.
PAGE 1315
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1316
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.
PAGE 1317
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 6.2.
PAGE 1318
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1319
Usage Information Example Related Commands Version Description pre- 6.2.1.1 Introduced on the E-Series. To enable RIP, assign a network address using the network command. DellEMC(conf)# router rip DellEMC(conf-router_rip)# ● network — enables RIP. ● exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration. The default values are not shown. Syntax show config Command Modes ROUTER RIP Command History Example This guide is platform-specific.
PAGE 1320
show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Syntax show ip rip database [ip-address mask] Parameters ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If you enter an IP address, also enter a mask for that IP address. mask (OPTIONAL) Specify a mask, in /network format, for the IP address.
PAGE 1321
Example DellEMC# show ip rip database Total number of routes in RIP database: 1624 204.250.54.0/24 [50/1] via 192.14.1.3, 00:00:12, twentyFiveGigE 1/15 204.250.54.0/24 auto-summary 203.250.49.0/24 [50/1] via 192.13.1.3, 00:00:12, twentyFiveGigE 1/14 203.250.49.0/24 auto-summary 210.250.40.0/24 [50/2] via 1.1.18.2, 00:00:14, Vlan 18 [50/2] via 1.1.130.2, 00:00:12, Port-channel 30 210.250.40.0/24 auto-summary 207.250.53.0/24 [50/2] via 1.1.120.2, 00:00:55, Port-channel 20 [50/2] via 1.1.130.
PAGE 1322
Version Description 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Example DellEMC# show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.0.0 passive-interface twentyFiveGigE 1/2 neighbor 20.20.20.20 redistribute ospf 999 version 2 DellEMC# timers basic Manipulate the RIP timers for routing updates, invalid, holddown times, and flush time.
PAGE 1323
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.
PAGE 1324
Related Commands 1324 Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ● ip rip receive version — sets the RIP version the interface receives. ● ip rip send version — sets the RIP version the interface sends.
PAGE 1325
46 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1326
variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table.
PAGE 1327
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1328
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1329
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
PAGE 1330
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1331
show rmon Display the RMON running status including the memory usage. Syntax show rmon Defaults none Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1332
Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) 1332 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1333
10 1.3.6.1.2.1.1.3 11 1.3.6.1.2.1.1.3 12 1.3.6.1.2.1.1.3 13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table. Syntax Parameters Defaults show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry.
PAGE 1334
Example (Index) Example (Brief) 1334 DellEMC(conf)# rmon event 111 -> DellEMC(conf)# rmon event 112 log -> DellEMC(conf)# rmon event 113 trap private -> DellEMC(conf)# rmon event 114 log trap public-> options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none. event community: event last time sent: none event owner: event status: OK RMON event entry 112 description: event type: LOG.
PAGE 1335
show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. Syntax Parameters Defaults show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) This guide is platform-specific.
PAGE 1336
Example (Brief) DellEMC# show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 DellEMC# show rmon history Display the contents of the RMON Ethernet history table. Syntax show rmon history [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry.
PAGE 1337
bucket requested: 1 bucket granted: 1 sampling interval: 5 sec owner: 1 status: OK DellEMC# Example (Brief) DellEMC# show rmon history brief index ifIndex interface --------------------------------------------------------------------6001 100974631 twentyFiveGigE 1/2 6002 100974631 twentyFiveGigE 1/3 6003 101236775 twentyFiveGigE 1/1 6004 101236775 twentyFiveGigE 1/4 9001 134529054 twentyFiveGigE 1/5 9002 134529054 twentyFiveGigE 1/6 9003 134791198 twentyFiveGigE 1/7 9004 134791198 twentyFiveGigE 1/8 DellEM
PAGE 1338
Usage Information Example (Index) Example (Brief) Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The log table has a maximum of 500 entries. If the log exceeds that maximum, the oldest log entry is purged to allow room for the new entry.
PAGE 1339
Example (Index) Example (Brief) Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon statistics 6001 RMON statistics entry 6001 interface: ifIndex.
PAGE 1340
47 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1341
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1342
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1343
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. ● protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command.
PAGE 1344
forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters Defaults seconds Enter the number of seconds that Dell EMC Networking OS waits before transitioning RSTP to the forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1345
milli-second Defaults Enter the keywords milli-second to configure a hello time on the order of milliseconds. The range is from 50 to 950 milliseconds 2 seconds Command Modes CONFIGURATION RSTP (conf-rstp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 1346
Defaults 20 seconds Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1347
Usage Information Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1348
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC(conf-rstp)# show config ! protocol spanning-tree rstp no disable bridge-priority 16384 show spanning-tree rstp Display the RSTP configuration.
PAGE 1349
Usage Information Example (Brief) Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) caused by loopback BPDU inconsistency. 6.2.1.1 Introduced on the E-Series. The following describes the show spanning-tree rstp guard command shown in the following example. Field Description Interface Name RSTP interface. Instance RSTP instance.
PAGE 1350
Root Bridge hello time 2, max age 20, forward delay 15, max hops 0 Bridge Identifier has priority 32768, Address 0001.e801.6aa8 Configured hello time 2, max age 20, forward delay 15, max hops 0 We are the root Current root has priority 32768, Address 0001.e801.6aa8 Number of topology changes 1, last change occurred 00:00:31 ago on Tf 1/1 Port 257 (twentyFiveGigE 1/1) is LBK_INC Discarding Port path cost 20000, Port priority 128, Port Identifier 128.257 Designated root has priority 32768, address 0001.e801.
PAGE 1351
Defaults Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON.
PAGE 1352
Example DellEMC(conf)# interface twentyFiveGigE 1/1 DellEMC(conf-if-tf-1/1)# spanning-tree rstp edge-port DellEMC(conf-if-tf-1/1)# show config ! interface twentyFiveGigE 1/1 no ip address switchport spanning-tree rstp edge-port no shutdown DellEMC# tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command.
PAGE 1353
48 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant. Topics: • • • • • • • • • • • • AAA Accounting Commands Authorization and Privilege Commands Obscure Password Commands Authentication and Password Commands RADIUS Commands TACACS+ Commands Port Authentication (802.
PAGE 1354
commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: ● For name, enter a user-defined name of a list of accounting methods. ● For default, the default accounting methods used.
PAGE 1355
Example (TACACS+) DellEMC(conf)# aaa accounting exec default start-stop tacacs+ DellEMC(conf)# aaa accounting command 15 default start-stop tacacs+ DellEMC(conf)# aaa accounting command role secaadmin default start-stop tacacs+ Example (RADIUS) Related Commands DellEMC(conf)# aaa accounting dot1x default start-stop radius DellEMC(conf)# aaa accounting dot1x default stop-only radius ● ● ● ● enable password — changes the password for the enable command.
PAGE 1356
records from being generated for sessions that do not have user names associated to them, use the aaa accounting suppress command. accounting Apply an accounting method list to terminal lines. Syntax accounting {exec | commands {level | role role-name} method-list Parameters Defaults exec Enter the keyword exec to apply an EXEC level accounting method list.
PAGE 1357
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1358
Usage Information Example Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.
PAGE 1359
Parameters Defaults exec Enter the keyword exec to apply an EXEC level authorization method list. commands { level | role role-name } Enter the keyword commands followed by either a privilege level for accounting of commands executed at that privilege level, or enter the keyword role then the role name for authorization of commands executed by a user with that user role. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands.
PAGE 1360
Defaults role role-name Enter the keyword role then the role name. name Define a name for the list of authorization methods. default Define the default list of authorization methods. local Use the authorization parameters on the system to perform authorization. tacacs+ Use the TACACS+ protocol to perform authorization. none Enter the keyword none to apply no authorization. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1361
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1362
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1363
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1364
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1365
authentication by obscuring this information. Passwords and keys are stored encrypted in the configuration file and by default are displayed in the encrypted form when the configuration is displayed. Enabling theservice obscure-passwords command displays asterisks instead of the encrypted passwords and keys. This command prevents a user from reading these passwords and keys by obscuring this information with asterisks.
PAGE 1366
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1367
● enable: use the password the enable password command defines in CONFIGURATION mode. Not available if role-only is in use. ● line: use the password the password command defines in LINE mode. Not available if role-only is in use. ● local: use the password for the userid contained in the local password database. ● none: no authentication. Not available if role-only is in use. ● radius: use the RADIUS servers configured with the radius-server host command.
PAGE 1368
the next method configured. If users fail the first method listed, no other methods are applied. The only exception is the local method. If the user’s name is not listed in the local database, the next method is applied. If the correct user name/password combination is not entered, the user is not allowed access to the switch. NOTE: If authentication fails using the primary method, Dell EMC Networking OS employs the second method (or third method, if necessary) automatically.
PAGE 1369
access-class Restrict incoming connections to a particular IP address in a defined IP access control list (ACL). Syntax access-class access-list-name To delete a setting, use the no access-class command. Parameters Defaults access-list-name Enter the name of an established IP Standard ACL. Not configured. Command Modes LINE Command History Related Commands This guide is platform-specific.
PAGE 1370
encryption-type (OPTIONAL) Enter the number 7 or 0 as the encryption type. Enter a 7 then a text string as the hidden password. The text string must be a password that was already encrypted by a Dell EMC Networking router. Use this parameter only with a password that you copied from the show running-config file of another Dell EMC Networking router. password Defaults Enter a text string, up to 96 characters long, as the clear text password. No password is configured. level = 15.
PAGE 1371
enable sha256-password Configure SHA-256 based password for the enable command. Syntax enable sha256-password [level level] [encryption-type] password To delete a password, use the no enable sha256-password [encryption-type] password [level level] command. Parameters sha256-password Enter the keyword sha256-password then the encryption-type or the password. level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 to 15.
PAGE 1372
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1373
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1374
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1375
● 0 is the default and means the password is not encrypted and stored as clear text. ● 7 means that the password is encrypted and hidden. password Defaults Enter a text string up to 96 characters long. The first character of the password must be a letter. You cannot use spaces in the password. No password is configured. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1376
To return to the default, use the no password-attributes [min-length number] [maxretry number] [lockout-period minutes] [character-restriction [upper number] [lower number] [numeric number] [special-char number]] command. Parameters min-length number max-retry number lockout-period minutes (OPTIONAL) Enter the keywords min-length then the number of characters. The range is from 0 to 32 characters. (OPTIONAL) Enter the keywords max-retry then the number of maximum password retries.
PAGE 1377
Example Version Description 9.5(0.0) Introduced lockout-period option on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series.
PAGE 1378
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1379
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1380
Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1381
To return to the default values, use the no timeout login response command. Parameters seconds Enter a number of seconds the software waits before logging you out. The range is: ● VTY — range is from 1 to 30 seconds, the default is 30 seconds. ● Console — range is from 1 to 300 seconds, the default is 0 seconds (no timeout). ● AUX — range is from 1 to 300 seconds, the default is 0 seconds (no timeout). Defaults See Parameters.
PAGE 1382
access-class Enter the keywords access-class then the name of a configured access control access-list-name list (either an IP access control list or MAC access control list). nopassword Enter the keyword nopassword to specify that the user should not enter a password. password Enter the keyword password then the encryption-type or the password. encryption-type Enter an encryption type for the password that you enter. ● 0 directs the system to store the password as clear text.
PAGE 1383
Usage Information Version Description 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for the secret option and the MD5 password encryption. Extended the name from 25 to 63 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1384
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.0P1) Introduced the command on all Dell EMC Networking OS platforms. If an authentication method is not configured using this command, then PAP is used for authentication with the RADIUS server.
PAGE 1385
ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections. Syntax ip radius source-interface interface To delete a source interface, use the no ip radius source-interface command. Parameters interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
PAGE 1386
radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped. Syntax radius-server deadtime seconds To disable this function or return to the default value, use the no radius-server deadtime command. Parameters Defaults seconds Enter a number of seconds during which non-responsive RADIUS servers are skipped. The range is from 0 to 2147483647 seconds. The default is 0 seconds.
PAGE 1387
Example Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1388
radius-server timeout command. The range is from 0 to 1000. The default is 5 seconds. key [ encryptiontype ] key (OPTIONAL) Enter the keyword key then an optional encryption-type and a string up to 42 characters long as the authentication key. The RADIUS host server uses this authentication key and the RADIUS daemon operating on this switch. For the encryption-type, enter either zero (0) or 7 as the encryption type for the key entered.
PAGE 1389
The global default values for the timeout, retransmit, and key optional parameters are applied, unless those values are specified in the radius-server host or other commands. To return to the global default values, if you configure the timeout, retransmit, or key values, include those keywords when using the no radius-server host command syntax. You can use duplicate host names or IP addresses among RADIUS groups. However, you cannot use duplicate host names or IP addresses within the same RADIUS group.
PAGE 1390
● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes RADIUS SERVER GROUP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1391
● 0 is the default and means the key is not encrypted and stored as clear text. ● 7 means that the key is encrypted and hidden. key Defaults Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 96 characters long. Not configured. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific.
PAGE 1392
Parameters Defaults retries Enter a number of attempts that the Dell OS tries to locate a RADIUS server. The range is from zero (0) to 100. The default is 3 retries. 3 retries Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 1393
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1394
Usage Information Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. If the TACACS group is not configured for Authentication, Authorization, and Accounting, then globally configured TACACS servers are used for the purposes.
PAGE 1395
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections. Syntax ip tacacs source-interface interface To delete a source interface, use the no ip tacacs source-interface command.
PAGE 1396
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. tacacs-server group Creates a group of TACACS servers.
PAGE 1397
tacacs-server host 2.2.2.2 key 7 9a2f3ec0c65c6f41 DellEMC(conf-tacacs-group)# Related Commands ● aaa authentication login — specifies the login authentication method. ● tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server host Specify a TACACS+ host. Syntax Parameters Defaults tacacs-server host {hostname | ipv4-address | ipv6-address} [port number] [timeout seconds] [key key] hostname Enter the name of the TACACS+ server host.
PAGE 1398
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times. If you are not configuring the switch as a TACACS+ server, you do not need to configure the port, timeout and key optional parameters. If you do not configure a key, the key assigned in the tacacsserver key command is used.
PAGE 1399
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.
PAGE 1400
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1401
● If 802.1X is disabled on the port, it is returned to the configured access VLAN. ● When the port is in the Force Authorized, Force Unauthorized, or Shutdown state, it is placed in the configured access VLAN. ● If an 802.1X port is authenticated and put in the RADIUS server assigned VLAN, any change to the port access VLAN configuration does not take effect. ● The 802.
PAGE 1402
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1403
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. If the host responds to 802.1X with an incorrect login/password, the login fails.
PAGE 1404
Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured.
PAGE 1405
Related Commands ● dot1x auth-fail-vlan — configures a VLAN for authentication failures. ● dot1x reauthentication — enables periodic re-authentication. ● show dot1x interface — displays the 802.1X information on an interface. dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell EMC Networking OS attempts to authenticate the host based on its MAC address.
PAGE 1406
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1407
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator performs authentication only when port-control is set to auto.
PAGE 1408
Version Description 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic re-authentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic re-authentication, use the no dot1x reauthentication command. Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated. The range is from 1 to 31536000 (1 year). The default is3600 (1 hour).
PAGE 1409
Parameters Defaults number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1410
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1411
Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs are transmitted by the Authenticator PAE. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters Defaults seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535 (1 year). The default is 30.
PAGE 1412
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information.
PAGE 1413
Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: DellEMC# 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Initialize Initialize DellEMC# show dot1x interface fortyGigE 1/49/1 802.
PAGE 1414
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Removed support for rsa1 keys from all platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1415
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1416
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Debug information includes details for key-exchange, authentication, and established session for each connection. ip scp topdir Identify a location for files used in secure copy transfer. Syntax ip scp topdir directory To return to the default setting, use the no ip scp topdir command.
PAGE 1417
ip ssh authentication-retries Configure the maximum number of attempts that should be used to authenticate a user. Syntax Parameters Defaults ip ssh authentication-retries 1-10 1-10 Enter the number of maximum retries to authenticate a user. The range is from 1 to 10. The default is 3. 3 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1418
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the S4810, S4820T, S3048–ON, S3100 Series, S4048–ON, S5000, S6000, S6000–ON, Z9500, Z9100–ON, S6100–ON, S6010–ON, S4048T–ON, C9000, and MXL.
PAGE 1419
● When the cipher (-c) option is used with the SSH CLI, it overrides the configured or default cipher list. ● When FIPS is enabled or disabled, the client ciphers get default configuration. ip ssh connection-rate-limit Configure the maximum number of incoming SSH connections per minute. Syntax Parameters Defaults ip ssh connection-rate-limit 1-60 1-60 Enter the number of maximum numbers of incoming SSH connections allowed per minute. The range is from 1 to 60 per minute. The default is 10 per minute.
PAGE 1420
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.0) Introduced on the S6000–ON, S6100–ON and Z9100–ON. ip ssh connection-rate-lockout Configure a lockout period until which the SSH connections are blocked, after the SSH connection attempts reach the rate limit.
PAGE 1421
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you enable this command, clients can log in without a password prompt.
PAGE 1422
● ● ● ● ● hmac-sha2-256 hmac-sha1 hmac-sha1–96 hmac-md5 hmac-md5-96 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1423
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. With password authentication enabled, you can authenticate using the local, RADIUS, or TACACS+ password fallback order as configured.
PAGE 1424
ip ssh pub-key-file Specify the file used for host-based authentication. Syntax ip ssh pub-key-file {WORD} Parameters Defaults WORD Enter the file name for the host-based authentication. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1425
ip ssh rhostsfile Specify the rhost file used for host-based authorization. Syntax Parameters Defaults ip ssh rhostsfile {WORD} WORD Enter the rhost file name for the host-based authentication. none Command Modes CONFIGURATION Command History Example Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1426
ip ssh rsa-authentication (Config) Enable RSA authentication for the SSHv2 server. Syntax ip ssh rsa-authentication enable To disable RSA authentication, use the no ip ssh rsa-authentication enable command. Parameters Defaults enable Enter the keyword enable to enable RSA authentication for the SSHv2 server. Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1427
Parameters enable Enter the key word enable to start the SSH server. ciphers cipher- Enter the keyword ciphers and then a space-delimited list of ciphers that the SSH server supports. The following ciphers are available. list ● 3des-cbc ● aes128-cbc ● aes192-cbc ● aes256-cbc ● aes128-ctr ● aes192-ctr ● aes256-ctr The default cipher list is used.
PAGE 1428
When FIPS is enabled, the default key-exchange-algorithm is diffie-hellmangroup14-sha1. When FIPS is not enabled, the default key-exchange-algorithms are the following: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1, ● diffie-hellman-group14-sha1 port port-number (OPTIONAL) Enter the keyword port then the port number of the listening port of the SSH server. The range is from 1 to 65535. The default is 22.
PAGE 1429
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22. NOTE: Starting with Dell EMC Networking OS Release 9.2(0.0), SSH server is enabled by default.
PAGE 1430
Usage Information You can enable the SSH server on either a management VRF or a user defined VRF but not both. If no VRF is specified, then the SSH server is enabled on the default VRF. If the SSH server is enabled on a VRF with name vrf1, then use the following command to restart the SSH server on a VRF with name vrf2: ip ssh server vrf vrf2. If the SSH server is enabled on a VRF with name vrf1, then use the following command to restart the SSH server on the default VRF: ip ssh server vrf.
PAGE 1431
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. The source-interface interface attribute is applicable for both the SSH client as well as the COPY (SCP) commands.
PAGE 1432
Example DellEMC(conf)#ip ssh vrf vrf1 DellEMC(conf)#do ssh 10.10.10.2 -l admin DellEMC(conf)#no ip ssh vrf vrf1 show crypto Display the public part of the SSH host-keys. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. show crypto key mypubkey {rsa} Parameters Defaults Key Enter the keyword key to display the host public key. mypubkey Enter the keyword mypubkey to display the host public key.
PAGE 1433
DellEMC# Related Commands ● crypto key generate — generates the SSH keys. show ip ssh Display information about established SSH sessions. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. show ip ssh Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1434
Password Authentication : Hostbased Authentication : RSA Authentication : Challenge Response Auth : Vty Encryption 2 aes128-cbc 4 aes128-cbc * 5 aes128-cbc DellEMC# Related Commands enabled. disabled. disabled. enabled. HMAC hmac-md5 hmac-md5 hmac-md5 Remote IP 10.16.127.141 10.16.127.141 10.16.127.141 ● ip ssh server — configures an SSH server. ● show ip ssh client-pub-keys — displays the client-public keys. show ip ssh client-pub-keys Display the client public keys used in host-based authentication.
PAGE 1435
yLPI5eehQTyaldRPHtGyPlcmMbCH +QJkqtyiwDPmH4njyDMYDCXY85vc55ibWsN9qalagklnh2cj2q4nYj5x8+8OOhYeFPaHiygd8U/ FXict61jWs84Co1UTsAgRzDJ9aUSS75TVac= root@dt-maa-li nux-1.force10networks.com 10.16.151.
PAGE 1436
zCMlnCf0+qVTd1oofsea5r09kS0xTp0CNfHXZ3NuGCq9Ov33m9+ U9tMwhS8vy8AVxdH4x4km3c3t5Jvc= freedom@poclab4 DellEMC# Related Commands ● ip ssh rsa-authentication (Config) — configures the RSA authorized keys. ssh Open an SSH connection specifying the hostname, username, encryption cipher, HMAC algorithm, port number, and version of the SSH client. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1437
● ● ● ● ● Defaults hmac-md5: Force ssh to use hmac-md5 HMAC algorithm. hmac-md5-96: Force ssh to use hmac-md5-96 HMAC algorithm. hmac-sha1: Force ssh to use hmac-sha1 HMAC algorithm. hmac-sha1-96 : Force ssh to use hmac-sha1-96 HMAC algorithm. hmac-sha2-256 : Force ssh to use hmac-sha2-256 HMAC algorithm. -p port-number (OPTIONAL) Enter the keyword -p then the port number. The range is from 1 to 65535. The default is 22. -v 2 (OPTIONAL) Enter the keyword -v then the SSH version 2.
PAGE 1438
Usage Information Example Version Description pre-6.1.1.0 Introduced on the E-Series. Dell EMC Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. DellEMC#ssh 10.16.151.48 -l anvltest Trying 10.16.151.48... 01:18:16: %STKUNIT0-M:CP %SEC-5-SSH_USAGE: Initiated SSH Client v2 (FIPS Disabled) to anvltest@10.16.151.
PAGE 1439
Related Commands ● show ip dhcp snooping — display the contents of the DHCP binding table. ip dhcp relay Enable Option 82. Syntax Parameters Defaults ip dhcp relay information-option [trust-downstream | vrf] trustdownstream Configure the system to trust Option 82 when it is received from the previous-hop router. vrf Enter the keyword vrf to include VRF related information in the Option 82.
PAGE 1440
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1441
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. Defaults slot/port Enter the slot and port number of the interface. lease time Enter the keyword lease then the amount of time the IP address is leased. The range is from 1 to 4294967295. none Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1442
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1443
ip dhcp source-address-validation Enable IP source guard. Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 1444
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information When enabled, the system begins creating entries in the binding table for the specified VLANs.
PAGE 1445
Related Commands ● clear ip dhcp snooping — clear the contents of the DHCP binding table. Role-Based Access Control Commands With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role. Users are granted permissions based on their user roles, not on their individual user ID. User roles are created for job functions and through those roles they acquire the permissions to perform their associated job function.
PAGE 1446
4. Specify authorization method (RADIUS, TACACS+ or Local). 5. Verify the configuration has been applied to the console or VTY line. Related Commands login authentication, password, radius-server host, tacacs-server host role Changes command permissions for roles.
PAGE 1447
Related Commands Version Description 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. ● userrole — creates user roles. show role Display information on permissions assigned to a command, including user role and/or permission level. Syntax Parameters show role mode {mode} {command} command Enter the command’s keywords to assign the command to a certain access level. You can enter one or all of the keywords. mode mode Enter keyword then one of the following modes.
PAGE 1448
Related Commands ● userrole — create user roles. show userroles Display information on all defined user roles.
PAGE 1449
userrole Create user roles for the role-based security model. Syntax userrole name inherit existing-role-name To delete a role name, use the no userrole name command. Note that the reserved role names may not be deleted. Parameters name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1450
role mode { { { addrole | deleterole } role-name } | reset } command – Modifies (adds or deletes) command permissions for newly created user roles and system defined roles. Related Commands ● role mode { { { addrole | deleterole } role-name } | reset } command — modifies (adds or deletes) command permissions for newly created user roles and system defined roles.
PAGE 1451
Table 8.
PAGE 1452
boot-access password Set a password for the boot loader. Syntax boot-access password [encryption-type] boot-password To remove the GRUB access password, use the no boot-access password command. Parameters encryption-type (OPTIONAL) Enter an encryption type for the boot password. ● 0 directs the system to store the password as clear text. ● 7 directs the system to store the password with a dynamic salt. boot-password Defaults Enter the boot access password. None Command Modes CONFIGURATION.
PAGE 1453
generate hash Generate a hash checksum for the given file or the startup configuration using the MD5, SHA1, or SHA256 algorithm. Syntax Parameters Defaults generate hash {md5 | sha1 | sha256} {flash://filename | startup-config} md5 | sha1 | sha256 Enter the keyword md5, sha1, or sha256 to generate . flash:// filename Enter the keyword flash: and enter the filename to generate the hash checksum for any file in the flash drive using the MD5, SHA1, or SHA256 algorithm.
PAGE 1454
Usage Information Version Description 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM. If you configure the secure-cli command on the system, the Dell EMC Networking OS resets any previously-configured root access password to the default root password without displaying any warning message.
PAGE 1455
Parameters Defaults system-image {A: Enter the keyword system-image and A: or B:, depending on where the image | B:} is stored and then the hash value that is present on the iSupport page for your image. startup-config Enter the keyword startup-config and then the hash value for the startup configuration. You can get the hash value for the startup configuration using the generate hash command. hash value Enter the MD5, SHA1, or SHA256 hash.
PAGE 1456
49 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1457
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID.
PAGE 1458
stp Defaults Enter the keyword stp to enable protocol tunneling on a spanning tree, including STP, MSTP, RSTP, and PVST. none Command Modes CONF-IF-VLAN Command History Example Related Command This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1459
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1460
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.4.1.0 Introduced Dell EMC Networking OS must have the default CAM profile with the default microcode before you enable L2PT. protocol-tunnel rate-limit Enable traffic rate limiting per box.
PAGE 1461
Example Related Commands DellEMC(conf-if-vl-2)# vlan-stack compatible DellEMC(conf-if-vl-2-stack)#protocol-tunnle rate-limit 100 <<<<<<<< VLAN stack mode DellEMC(conf-if-vl-2-stack)#show config ! interface Vlan 2 no ip address mtu 1000 vlan-stack compatible protocol-tunnel rate-limit 100 shutdown ● show protocol-tunnel — displays tunneling information for all VLANs. ● show running-config — displays the current configuration.
PAGE 1462
1001 1002 1003 1004 1005 Example (Specific VLAN) Related Commands 1462 LLDP,GVRP MMRP,MVRP LACP,DOT1X OAM,PAUSE E-LMI Tf Tf Tf Tf Tf 1/7,Tf 1/7,Tf 1/7,Tf 1/7,Tf 1/7,Tf 1/6 1/6 1/6 1/6 1/6 DellEMC# show protocol-tunnel vlan 2 System Rate-Limit: 1000 Frames/second Interface Vlan Protocol(s) Tw1/2 2 STP, PVST DellEMC# ● show running-config — displays the current configuration.
PAGE 1463
50 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1464
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
PAGE 1465
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
PAGE 1466
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default.
PAGE 1467
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S-Series, Z-Series, and MXL switch. 9.2(1.0) Introduced on the Z9500.
PAGE 1468
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1469
sflow polling-interval (Global) Set the sFlow polling interval at a global level. Syntax sflow polling-interval interval value To return to the default, use the no sflow polling-interval interval command. Parameters Defaults interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is 20 seconds. 20 seconds Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1470
To return to the default, use the no sflow polling-interval interval command. Parameters Defaults interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is the global counter polling interval. The same value as the current global default counter polling interval. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1471
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1472
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1473
● For the Management interface on the, enter the keyword ManagementEthernet then the slot/port information. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1474
based on line speed if global sampling rate is default DellEMC# 1474 sFlow
PAGE 1475
51 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1476
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1477
Example Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1478
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
PAGE 1479
IPV6-FLOW-LABEL-MIB SNMPv2-MIB IF-MIB IP-MIB TCP-MIB UDP-MIB RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1 1.3.6.1.2.1.31 1.3.6.1.2.1.48 1.3.6.1.2.1.49 1.3.6.1.2.1.50 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform.
PAGE 1480
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1481
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1482
rw Enter the keyword rw to specify read-write permission. ipv6 access-list- (Optional) Enter the keyword ipv6 then an IPv6 ACL name (a string up to 16 characters long). name security-name name (Optional) Enter the keywords security-name then the security name as defined by the community MIB. access-list-name (Optional) Enter a standard IPv4 access list name (a string up to 16 characters long).
PAGE 1483
NOTE: For IPv6 ACLs, only IPv6 and UDP types are valid for SNMP; TCP and ICMP rules are not valid for SNMP. In IPv6 ACLs, port rules are not valid for SNMP. Example Example Related Commands DellEMC# config DellEMC(conf)# snmp-server community public ro DellEMC(conf)# snmp-server community guest ro security-name guestuser DellEMC(conf)# DellEMC(conf)# ip access-list standard snmp-ro-acl DellEMC(config-std-nacl)#seq 5 permit host 10.10.10.
PAGE 1484
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps. Syntax snmp-server enable traps [notification-type] [notification-option] To disable traps, use the no snmp-server enable traps [notification-type] [notification-option] command. Parameters notification-type Enter the type of notification from the following list: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● notificationoption bgp — Enable BGP state change traps.
PAGE 1485
Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 1486
● The first four octets are set to the private enterprise number. ● The remaining eight octets are the MAC address of the chassis. remote ip- address vrf vrf-name Enter the keyword vrf followed by the name of the VRF that is used to reach the device. NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device. If no VRF is specified, then the default VRF is used.
PAGE 1487
● show running-config snmp — displays the SNMP running configuration. snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
PAGE 1488
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1489
NOTE: The :: notation specifies successive hexadecimal fields of zero. vrf vrf-name Enter the keyword vrf and then the name of the VRF that the SNMP server uses to connect to the host. NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host.
PAGE 1490
● vrrp — Enable VRRP state change traps. ● xstp — Enable 802.1s, 802.1w, and PVST+ state change traps. The default is all trap types are sent to host. Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.12(0.
PAGE 1491
NOTE: For v1 / v2c trap configuration, if the community-string is not defined using the snmpserver community command prior to using this command, the default form of the snmp-server community command automatically is configured with the community-name the same as specified in the snmp-server host command. NOTE: You must configure notify option for the SNMPv3 traps to work. Configuring Informs To send an inform, use the following steps: 1. 2. 3. 4. 5. Related Commands Configure a remote engine ID.
PAGE 1492
Version Description E-Series legacy command snmp-server packetsize Set the largest SNMP packet size permitted. Wen the SNMP server is receiving a request or generating a reply, use the snmpserver packetsize global configuration command. Syntax snmp-server packetsize byte-count Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32. Packet sizes are 8000 bytes, 16000 bytes, 32000 bytes, and 64000 bytes.
PAGE 1493
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 1494
snmp-server user Configure a new user to an SNMP group.
PAGE 1495
priv password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the host to encrypt the contents of the message it sends to the agent. Minimum: eight characters long. access access- list-name (Optional) Enter the standard IPv4 access list name (a string up to 16 characters long). ipv6 access-listname (Optional) Enter the keyword ipv6 then the IPv6 access list name (a string up to 16 characters long).
PAGE 1496
Example Usage Information Example Usage Information Example Related Commands DellEMC# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv des56 d0452401a8c3ce42804fe80e3ba8763d The following command is an example of how to enter a plain-text password as the string authpasswd for user authuser of group v3group.
PAGE 1497
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.
PAGE 1498
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1499
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information Use this command to bind an SNMP agent to a VRF. The SNMP agent processes the requests from the interfaces that belong to the specified VRF.
PAGE 1500
Version Description E-Series legacy command Usage Information If the interface is expected to flap during normal usage, you could disable this command. Syslog Commands The following commands allow you to configure logging functions on all Dell EMC Networking switches. clear logging Clear the messages in the logging buffer. Syntax clear logging Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1501
clear logging auditlog Clears audit log. Syntax clear logging auditlog Defaults None Command Modes EXEC Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.
PAGE 1502
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging buffered — set the logging buffered parameters. default logging console Return the default settings for messages logged to the console.
PAGE 1503
default logging monitor Return to the default settings for messages logged to the terminal. Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1504
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1505
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Added udp and tcp keywords for the Z9500. 9.5(0.
PAGE 1506
size Defaults (OPTIONAL) Indicate the size, in bytes, of the logging buffer. The number of messages buffered depends on the size of each message. The range is from 40960 to 524288. The default is 40960 bytes. level = 7; size = 40960 bytes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1507
Defaults level = 7; size = debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 1508
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. This command is available with or without RBAC enabled.
PAGE 1509
● ● ● ● ● ● ● ● sys10 (system use) sys11 (system use) sys12 (system use) sys13 (system use) sys14 (system use) syslog (Syslog process) user (user process) uucp (Unix to Unix copy process) The default is local7. Defaults local7 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1510
Parameters Defaults level Indicate a value from 0 to 7 or enter one of the following equivalent words: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 4 or warnings. warnings or 4 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1511
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1512
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.
PAGE 1513
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you use the no logging on command, messages are logged only to the console. Related Commands ● ● ● ● logging logging logging logging — enable logging to the Syslog server. buffered — set the logging buffered parameters.
PAGE 1514
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.
PAGE 1515
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1516
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1517
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. To display syslog messages in a RFC 3164 or RFC 5424 format, use the log version command in configuration mode. By default, the system log version is set to 0.
PAGE 1518
show logging Display the logging settings and system messages logged to the internal buffer of the switch. Syntax show logging [number | history [reverse][number] | reverse [number] | summary] Parameters number (OPTIONAL) Enter the number of messages displayed in the output. The range is from 1 to 65535. history (OPTIONAL) Enter the keyword history to view only information in the Syslog history table.
PAGE 1519
Oct 8 09:25:37: %RPM1:RP1 %BGP-5-ADJCHANGE: 223.80.255.254 closed.
PAGE 1520
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 1521
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1522
52 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1523
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
PAGE 1524
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
PAGE 1525
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 TRAP OID Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
PAGE 1526
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1527
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
PAGE 1528
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
PAGE 1529
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
PAGE 1530
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
PAGE 1531
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1532
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
PAGE 1533
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
PAGE 1534
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE lldp-ext-med.
PAGE 1535
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
PAGE 1536
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 113 MIB File Explanation TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
PAGE 1537
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE Object Name MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
PAGE 1538
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 132 TR_VLT_ICL_BW_ THRESHOLD_EXC EED 133 TR_VLT_DOMAIN _CFG_ERROR 134 135 1538 SNMP Traps Object Name MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclBwUs .2.0.5 ageExceed DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The IFM agent generates this notification to denote the change in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1.
PAGE 1539
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 138 TR_ENT_CONFIG_ 1.3.6.1.2.1.47.2.0.1 CHANGE Object Name MIB File Explanation entConfigChange entity.mib An entConfigChange notification is generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls. An agent should not generate more than one entConfigChange 'notification-event' in a given time interval (five seconds is the suggested default).
PAGE 1540
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation notificationevents, e.g., due to throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.
PAGE 1541
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
PAGE 1542
53 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1543
• • • • • • • • show storm-control multicast show storm-control unknown-unicast storm-control broadcast (Configuration) storm-control broadcast (Interface) storm-control multicast (Configuration) storm-control multicast (Interface) storm-control unknown-unicast (Configuration) storm-control unknown-unicast (Interface) polling-interval You can set the time interval to poll the queue depth and egress counters.
PAGE 1544
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6000, S6000–ON, S61000–ON, Z9100–ON. Usage Information The xoff-state threshold polling-count command is used to set the number of times the polling should be done. If a port/priority remains in the ‘xoff’ state for the configured threshold number of polling-intervals, then it would be detected as PFC storm condition.
PAGE 1545
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6000, S6000–ON, S61000–ON, Z9100–ON.
PAGE 1546
storm-control pfc in queue-drop-state clear You can clear the queue-drop state on an interface where the PFC storm has been triggered. Syntax storm-control pfc in queue-drop-state clear Parameters None Defaults None Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1547
show storm-control pfc status You can view the status of the PFC storm on a stack unit with specific port set. Syntax Parameters show storm-control pfc status stack-unit {unit-number} port-set {portpipe-number} unit-number Enter the stack unit number. portpipe-number Enter the port set number. Defaults None Command Modes EXEC Privilege. Command History Usage Information Example This guide is platform-specific.
PAGE 1548
Related Commands show storm-control pfc status — view the status of the PFC storm on a stack unit with a specific port set. show storm-control pfc statistics You can view the statistical details of the PFC storm on a stack unit with specified port set. Syntax show storm-control pfc statistics stack-unit {unit-number} port-set {portpipe-number Parameters unit-number Enter the stack unit number. portpipe-number Enter the port set number. Defaults None Command Modes EXEC Privilege.
PAGE 1549
clear storm-control pfc statistics Clears the discard state count and cleared count statistics. If the queue is in discard state during clear, the discard state count will start from 1. Syntax Parameters clear storm-control pfc statistics stack-unit {unit-number} port-set {portpipe-number} unit-number Enter the stack unit number. portpipe-number Enter the port set number. Defaults None Command Modes EXEC Privilege. Command History This guide is platform-specific.
PAGE 1550
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1551
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1552
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1553
packets_per_sec ond in Defaults Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368. none Command Modes CONFIGURATION (conf) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1554
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1555
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMUX (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series.
PAGE 1556
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. storm-control unknown-unicast (Configuration) Configure the percentage of unknown-unicast traffic allowed in or out of the network. Syntax storm-control unknown-unicast [packets_per_second in] To disable storm control for unknown-unicast traffic, use the no storm-control unknownunicast [packets_per_second in] command.
PAGE 1557
storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only). Syntax storm-control unknown-unicast [percentage decimal_value in] | [wred-profile name]] [packets_per_second in] To disable unknown-unicast storm control on the interface, use the no storm-control unknownunicast [percentage decimal_value in] | [wred-profile name]] [packets_per_second in] command.
PAGE 1558
54 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1559
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1560
debug spanning-tree Enable debugging of the spanning tree protocol and view information on the protocol. Syntax debug spanning-tree {stp-id [all | bpdu | config | events | exceptions | general | root] | protocol} To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp.
PAGE 1561
description Enter a description of the spanning tree. Syntax description {description} To remove the description from the spanning tree, use the no description {description} command. Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific.
PAGE 1562
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1563
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1564
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● forward-delay — changes the wait time before STP transitions to the Forwarding state. ● max-age — changes the wait time before STP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge.
PAGE 1565
protocol spanning-tree To enable and configure the spanning tree group, enter SPANNING TREE mode. Syntax protocol spanning-tree stp-id To disable the Spanning Tree group, use the no protocol spanning-tree stp-id command. Parameters Defaults stp-id Enter zero (0). Dell EMC Networking OS supports one spanning tree group, group 0. Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific.
PAGE 1566
Command Modes SPANNING TREE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1567
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information.
PAGE 1568
Field Description “Configured hello...” Displays the settings for hello time, max age, and forward delay. “We are...” States whether this bridge is the root bridge for the STG. “Current root...” Lists the bridge priority and MAC address for the root bridge. “Topology flag...” States whether the topology flag and the detected flag were set. “Number of...” Displays the number of topology changes, the time of the last topology change, and on what interface the topology change occurred.
PAGE 1569
Port path cost 4, Port priority 8, Port Identifier 8.28 Designated root has priority 32768, address 0001.e800.0a56 Designated bridge has priority 32768, address 0001.e800.0a56 Designated port id is 8.
PAGE 1570
● ● ● ● ● 1-Gigabit Ethernet interface = 4. 10-Gigabit Ethernet interface = 2. Port Channel interface with 100 Mb/s Ethernet = 18. Port Channel interface with 1 Gigabit Ethernet = 3. Port Channel interface with 10 Gigabit Ethernet = 1. loopguard Enter the keyword loopguard to enable STP loop guard on a port or port-channel interface. rootguard Enter the keyword rootguard to enable STP root guard on a port or port-channel interface.
PAGE 1571
Usage Information If you enable portfast bpduguard on an interface and the interface receives a BPDU, the software disables the interface and sends a message stating that fact. The port is in ERR_DISABLE mode, yet appears in the show interface commands as enabled. If you do not enable shutdown-onviolation, BPDUs are still sent to the RPM CPU.
PAGE 1572
55 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1573
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1574
SUPASSIST_PKG_UNINSTALLED: SupportAssist package uninstalled DellEMC(conf)# Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1575
Usage Information You are guided through a series of queries to configure SupportAssist. The generated commands are added to the running configuration, including the DNS resolve commands, if configured. This command starts the configuration wizard for the SupportAssist. At any time, you can exit by entering Ctrl-C. If necessary, you can skip some data entry. Once you exit the wizard, the Dell EMC Networking OS starts a full transfer. support-assist activity Trigger an activity event immediately.
PAGE 1576
● Enter the keyword core-transfer to enable or disable core transfer. ● Enter the keyword event-transfer to enable or disable event transfer. You can create a custom file to monitor a set of events. Command Modes SUPPORTASSIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.
PAGE 1577
This command is optional for SupportAssist service configuration. contact-person Configure the contact name for an individual. Syntax contact-person [first ] last To remove the contact person and all their details, use the no contact-person [first ] last command. Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes.
PAGE 1578
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode.
PAGE 1579
action-manifest get Copy an action-manifest file for an activity to the system. Syntax Parameters action-manifest get tftp | ftp | flash file-specification Enter the full file specification for the action-manifest file. For example: ● tftp://hostip/filepath ● ftp://userid:password@hostip/filepath ● scp://userid:password@hostip/filepath local-file-name Enter the name of the local action-manifest file, up to 32 characters long.
PAGE 1580
Command Modes SUPPORTASSIST ACTIVITY FULL-TRANSFER SUPPORTASSIST ACTIVITY EVENT-TRANSFER Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1581
action-manifest show View the list of action-manifest for a specific activity. Syntax Parameters action-manifest show {all} all Enter the keyword all to view the entire list of action-manifests that are available for an activity. Command Modes SUPPORTASSIST ACTIVITY FULL-TRANSFER SUPPORTASSIST ACTIVITY EVENT-TRANSFER Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1582
Usage Information Enter the specific SupportAssist activity mode and then enable it. NOTE: By default, the full transfer includes the core files. When you disable the core transfer activity, the full transfer excludes the core files. Related Commands ● activity — move user to the SupportAssist Activity mode for that activity. SupportAssist Company Commands Dell EMC Networking OS supports the following SupportAssist Company mode commands. address Configure the address information for the company.
PAGE 1583
This command is optional for SupportAssist service configuration. Example DellEMC(conf-supportassist-cmpy-test)# address city Minneapolis state Minnesota country USA postalcode 55344 street-address Configure the street address information for the company. Syntax street-address {address1} [address2]…[address8] To remove the street address, use the no street-address command. Parameters address1 Enter the street address for the company. address2..
PAGE 1584
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. SupportAssist Person Commands Dell EMC Networking OS supports the following SupportAssist Person mode commands. email-address Configure the email addresses to reach the contact person.
PAGE 1585
To remove a phone number, use the no phone command. To remove the primary and alternate phone numbers, use the no phone primary and no phone alternate commands respectively. Parameters primary phone Enter the keyword primary then the primary phone number for the person. alternate phone Enter the keyword alternate then the alternate phone number for the person. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific.
PAGE 1586
Related Commands ● email-address — configure email addresses to reach the contact person. ● phone — configure phone numbers to reach the contact person. time-zone Configure the time zone for contacting the person. Syntax time-zone zone +-HH:MM[start-time HH:MM] [end-time HH:MM] To remove the time zone, use the no time-zone [zone | start-time | end-time] command. Parameters zone +-HH:MM Enter the keyword zone then a time difference from GMT expressed as HH:MM.
PAGE 1587
NOTE: To use the IPv6 address, the Open Automation package should also support IPv6 communications. For this purpose, SupportAssist requires Dell EMC Networking Open Automation 9.10(0.0) package or later. port port-number Enter the keyword port then the TCP/IP port number. The port number range is from 1024 to 65534. username userid (OPTIONAL) Enter the keyword username then the user ID used for the proxy server. password Enter the keyword password then the encryption-type or the user password.
PAGE 1588
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. ● server — configure the name of the remote SupportAssist server. url Configure the URL to reach the SupportAssist remote server. Syntax url uniform-resource-locator To delete the URL for the server, use the no url command.
PAGE 1589
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1590
you may not download, install or otherwise use SupportAssist. DellEMC# show running-config Display the current configuration and changes from the default values. Syntax show running-config support-assist Parameters support-assist Enter the keyword support-assist to view the detailed configuration for the feature. Command Modes EXEC Privilege Command History Example 1590 This guide is platform-specific.
PAGE 1591
show support-assist status Display information on SupportAssist feature status including any activities, status of communication, last time communication sent, and so on. Syntax show support-assist status Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.
PAGE 1592
56 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1593
Defaults end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year.
PAGE 1594
Parameters time-zone Enter the three-letter name for the time zone. This name is displayed in the show clock output. You can enter up to eight characters. start-week (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: ● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month.
PAGE 1595
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key.
PAGE 1596
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone.
PAGE 1597
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1598
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option.
PAGE 1599
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1600
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Introduced on the S4810, S4820T, S5000, S6000, Z9000, and Z9500. 9.2(1.0) Introduced on the Z9500. ntp offset-threshold Configure the threshold time interval before which the system generates an NTP audit log message if the time difference from the NTP server is greater than a threshold value (offset-threshold). Syntax ntp offset-threshold threshold-value To disable the threshold value, use the no ntp offset-threshold command.
PAGE 1601
version number (OPTIONAL) Enter the keyword version and a number to correspond to the NTP version used on the server. The range is from 1 to 4. minpoll polling- (OPTIONAL) Enter the keyword minpollthen the polling-interval. The polling interval range is from 4 to 16. interval maxpoll polling- interval Defaults (OPTIONAL) Enter the keyword maxpollthen the polling-interval. The polling interval range is from 4 to 16. Not configured.
PAGE 1602
the system to the latest NTPD package in the NTP server and the system logs the following NTP syslog message: Dell EMC# May 30 13:27:46 %STKUNIT2-:CP %ntp-6-: receive: Unexpected origin timestamp 0xdeb95bee.06ba346e does not match aorg 0000000000.00000000 from server@10.16.151.117 xmt 0xdeb95bee.30907a87 In general, the packet denied services are dropped with no further action except incrementing the statistics counters.
PAGE 1603
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards.
PAGE 1604
To delete the key, use the no ntp trusted-key number command. Parameters Defaults number Enter a number as the trusted key ID. The range is from 1 to 65534. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced the trusted-key range update on the S4810 and S4820T. 9.14(0.
PAGE 1605
Defaults 7 Specify that the authentication key is entered in DES encrypted format. key Enter the authentication key in the previously specified format. NTP authentication is not configured by default. If you do not specify the option [0 | 7], 0 is selected by default. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1606
Parameters detail (OPTIONAL) Enter the keyword detail to view the source information of the clock. Command Modes ● EXEC ● EXEC Privilege Command History Example Example (Detail) Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1607
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Network OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1608
Example (without ntp master configuration) Example (with ntp master configuration) Field Description .LOCL. Indicates the reference clock of the NTP master. DellEMC# show ntp associations remote vrf-Id ref clock st when poll reach delay offset disp =============================================================================== *10.16.151.117 0 45.127.112.2 3 8 16 17 1.383 362.704 0.
PAGE 1609
Version Description 8.4.1.0 Added IPv6 support. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. show ntp status Display the current NTP status. Syntax show ntp status Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 1610
Field Description “clock offset is...” Displays the system offset to the synchronized peer and the time delay on the path to the NTP root clock. “root dispersion is...” Displays the root and path dispersion. “peer mode is...” State what NTP mode the switch is. This should be Client mode. Example Related Commands 1610 DellEMC#> show ntp status Clock is synchronized, stratum 4, reference is 10.16.151.117, vrf-id is 0 frequency is 0.000 ppm, stability is 0.
PAGE 1611
57 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1612
Usage Information Version Description 9.3(0.1) Introduced on the S5000 and Z9000. The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
PAGE 1613
NOTE: The ipv6 unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address. The tunnel interface is not changed to operationally up until the logical IP address is identified from one of the address family. tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted.
PAGE 1614
tunnel destination Set a destination endpoint for the tunnel. Syntax tunnel destination {ip-address | ipv6–address} To delete a tunnel destination address, use the no tunnel destination {ip-address | ipv6– address} command. Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific.
PAGE 1615
value Defaults Enter a value to set the DSCP value in the tunnel header. The range is from 0 to 63. The default value of 0 denotes mapping of original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/Traffic Class (IPv6) depending on the mode of tunnel. 0 (Mapped) Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific.
PAGE 1616
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. This command is only valid for tunnel interfaces with an IPv6 outer header.
PAGE 1617
tunnel keepalive Configure the tunnel keepalive target, interval and attempts. Syntax tunnel keepalive {ip-address | ipv6-address}[interval {seconds}] [attempts {count | unlimited}] To disable the tunnel keepalive probes use the no tunnel keepalive command. Parameters ip-address ipv6 address Enter the IPv4 or IPv6 address of the peer to which the keepalive probes will be sent.
PAGE 1618
tunnel-mode Enable a tunnel interface. . Syntax tunnel mode {ipip | ipv6 | ipv6ip}[decapsulate-any] To disable an active tunnel interface, use the no tunnel mode command. Parameters Defaults ipip Enable tunnel in RFC 2003 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv4 tunnel. ipv6 Enable tunnel in RFC 2473 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv6 tunnel. ipv6ip Enable tunnel in RFC 4213 mode and encapsulate IPv6 datagrams inside an IPv4 tunnel.
PAGE 1619
To delete the current tunnel source address, use the no tunnel source command. Parameters Defaults ip-address Enter the source IPv4 address in A.B.C.D format. ipv6–address Enter the source IPv6 address in X:X:X:X::X format. interface-typenumber ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information.
PAGE 1620
58 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1621
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1622
description Enter a text description of an uplink-state group. Syntax description text Parameters Defaults text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.
PAGE 1623
● For a 100-Gigabit interface, enter the keyword hundredGigE then the slot/ port/subport information. Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific.
PAGE 1624
Related Commands Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.
PAGE 1625
Usage Information Version Description 8.4.2.3 Introduced on the S-Series S50. When one upstream interface in an uplink-state group goes down, you can configure the number of downstream interfaces in an uplink-state group are put into a link-down state with an UFD-Disabled error message. If all upstream interfaces in an uplink-state group go down, all downstream interfaces in the same uplinkstate group are put into a link-down state.
PAGE 1626
Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1627
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1628
uplink-state-group Create an uplink-state group and enable the tracking of upstream links on a switch or router. Syntax uplink-state-group group-id To delete an uplink-state group, enter the no uplink-state-group group-id command. Parameters Defaults group-id Enter the ID number of an uplink-state group. The range is from 1 to 16. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1629
upstream Assign a port or port-channel to the uplink-state group as an upstream interface. Syntax upstream interface To delete an uplink-state group, use the no upstream interface command.
PAGE 1630
Related Commands 1630 ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. ● uplink-state-group — creates an uplink-state group and enables the tracking of upstream links.
PAGE 1631
59 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1632
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series.
PAGE 1633
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. Syntax Parameters Defaults dei mark {green | yellow} {0 | 1} 0|1 Enter the bit value you want to map to a color.
PAGE 1634
member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command. Parameters interface Enter the following keywords and the interface information: ● For a Port Channel interface, enter the keywords port-channel, and then a number.
PAGE 1635
vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network. Syntax vlan-stack access To remove access port designation, use the no vlan-stack access command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1636
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1637
Parameters c-tag-dot1p value Enter the keyword c-tag-dot1p then the customer dot1p value that is mapped to a service provider do1p value. The range is from 0 to 7. sp-tag-dot1p value Defaults Enter the keyword sp-tag-dot1p then the service provider dot1p value. The range is from 0 to 7. none Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1638
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series.
PAGE 1639
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1640
shutdown DellEMC(conf-if-vl-100-stack)# interface vlan 20 DellEMC(conf-if-vl-20)# tagged twentyFiveGigE 1/23 DellEMC(conf-if-vl-20)# show config ! interface Vlan 20 no ip address tagged twentyFiveGigE 1/23 shutdown DellEMC(conf-if-vl-20)# do show vlan Codes: * - Default VLAN, G - GVRP VLANs Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM Status Description * 1 Inactive 20 Active 100 Active DellEMC(conf-if-vl-20)# Example 2 Q Ports T Tf 1/23 M Tf 1/23 De
PAGE 1641
60 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • • ip unknown-unicast ipv6 unknown-unicast description ip vrf forwarding ip http vrf ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip unknown-unicast Enable IPv4 catch-all route.
PAGE 1642
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv6 unknown-unicast Disable soft forwarding of unknown IPv6 destination packets.
PAGE 1643
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1644
To assign a port-back to a default VRF, remove the VRF association from the interface. You can use this only if there is no IP address configured on the interface. There must be no prior Layer 3 configuration on the interface when configuring VRF. You must enable VRF before using this command. You can configure an IP subnet or address on a physical or VLAN interface that overlaps the same IP subnet or address configured on another interface only if the interfaces are assigned to different VRFs.
PAGE 1645
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To make the HTTP clients VRF-aware, use the ip http vrf command. The HTTP client uses the VRF name that you specify to reach the HTTP server.
PAGE 1646
In Dell EMC Networking OS, you can configure one route-export per VRF as you can only expose one set of routes for leaking. However, you can configure multiple route-import targets because a VRF can accept routes from multiple VRFs. You can expose a unique set of routes from the source VRF for leaking to other VRFs. When two VRFs leak or export routes, there is no option to discretely filter leaked routes from each source VRF.
PAGE 1647
ipv6 route-export Enables route leaking between VRFs. This command exports or shares IPv6 routes corresponding to one VRF with other nondefault VRFs. Syntax Parameters Defaults ipv6 route-export tag [route-map-name] route-export Enter the keywords route-export to leak or share routes between VRFs. tag Enter a tag (ASN number) as the export route target to expose routes to other VRFs. This tag acts as an identifier for exported routes.
PAGE 1648
ipv6 route-import Imports IPv6 routes that another VRF leaks using the tag that VRF specifies during export of these routes. Syntax ipv6 route-import tag [route-map-name] Parameters Defaults route-import Enter the keywords route-import to import IPv6 routes into the VRF. tag Enter a tag (ASN number) to specify an import route target for importing routes from another VRF. To import leaked routes from another VRF, use the same ASN number that is specified as the export route target at the source VRF.
PAGE 1649
connected Enter the keyword connected to leak or share connected routes corresponding to the VRF. static Enter the keyword static to leak or share static routes corresponding to the VRF. Command Modes ROUTE MAP MODE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1650
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. ● ip route-import — import routes from another VRF.
PAGE 1651
To remove the limit on the maximum number of routes used, use the no maximum dynamic-routes command. Parameters limit Maximum number of routes allowed in a VRF. The valid range is from 1 to 320,000 (or maximum allowable for that platform if a smaller value). warningthreshold The warning threshold value is a percentage of the limit value. When the number of routes reaches the specified percentage of the limit, a warning message appears. The valid range is from 1 to 100.
PAGE 1652
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 1653
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 1654
61 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1655
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax Parameters Defaults back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1656
Hence, the back-up destination command must be configured as: DellEMC(conf-vlt-domain)#back-up destination vrf management vrf-name clear vlt statistics Clear the VLT operation statistics. Syntax clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP.
PAGE 1657
ARP Reg Request sent:19 ARP Reg Request rcvd:10 Related Commands ● show vlt statistics — displays statistics on VLT operations. delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax Parameters Defaults delay-restore delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200.
PAGE 1658
delay-restore abort-threshold Increase the boot up timer to a value greater than 60 seconds. Syntax delay-restore abort-threshold To remove the boot up timer value, use the no delay-restore abort-threshold command. Parameters interval Enter the interval value (in seconds) for the delay restore timer to abort. The range is from 1 to 1800 seconds. The default is 60 seconds. This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap).
PAGE 1659
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 1660
multicast peer-routing timeout To retain synced multicast routes or synced multicast outgoing interface (OIF) after a VLT peer node failure, configure the timeout value for a VLT node. Syntax multicast peer-routing timeout value To restore the default value, use the no multicast peer-routing timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 1200. The default is 150. Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific.
PAGE 1661
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1662
Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the support for IPV6 / IPV4. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4.
PAGE 1663
primary-priority Assign the priority for master election among VLT peers. Syntax Parameters Default [no] primary-priority value To configure the primary role on a VLT peer, enter a lower value than the priority value of the remote peer. The range is from 1 to 65535. The default value is 32768. 32768 Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific.
PAGE 1664
Usage Information Example (Brief) Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 1665
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 1666
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1667
Total VLT Ndp Entries Synced : Total Non-VLT Ndp Entries Learnt : Total Non-VLT Ndp Entries Synced : 0 0 0 show vlt detail Displays detailed status information about VLT domains configured on the switch. Syntax show vlt detail Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 1668
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only.
PAGE 1669
Example Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000.
PAGE 1670
--------128 -------- ----------128 4094 ---------100 DellEMC# show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1671
show vlt statistics Displays VLT operations statistics. Syntax Parameters Default show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] arp Enter the keyword arp to display the ARP VLT statistics. domain Enter the keyword domain to display the domain VLT statistics. igmp-snoop Enter the keywords igmp-snoop to display the IGMP snooping VLT statistics. mac Enter the keyword mac to display the VLT MAC addresses VLT statistics.
PAGE 1672
Version Mismatch Errors: Config Mismatch Errors: 0 0 VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg Response rcvd: 1 IGMP PDU Tunnel Pkt sent: 5 IGMP PDU
PAGE 1673
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1674
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, the Dell EMC Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for internal system operations. To explicitly configure the unit ID of a VLT peer, use the unit-id command. Configure a different unit ID (0 or 1) on each peer switch.
PAGE 1675
vlt-peer-lag port-channel Associate the port channel to the corresponding VLT peer port channel for the VLT connection to an attached device. Syntax Parameters Defaults vlt-peer-lag port-channel id-number id-number Enter the respective VLT port-channel number of the peer device. Not configured. Command Modes INTERFACE PORT-CHANNEL Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1676
62 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1677
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1678
Usage Information Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1679
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link.
PAGE 1680
Example DellEMC(conf-vlt-domain-proxy-gw-lldp)# peer-timeout 5 vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 1681
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1682
63 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
PAGE 1683
Usage Information Use this command to clear the remote VTEP and access port statistics. clear mac-address-table dynamic Clear the MAC address table of specific or all MAC address learned dynamically.
PAGE 1684
Defaults Disabled Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.
PAGE 1685
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command-Line Reference Guide. Version Description 9.14(2.3) Introduced on the S4048–ON, S4048T-ON, S6000, S6010-ON, S6100-ON, and Z9100–ON. Use the disable-mac-learn command in the VXLAN-INSTANCE mode. NOTE: ● This command is only applicable for static VXLAN and does not work for the other modes of VXLAN (controller and nuage).
PAGE 1686
Parameters Defaults secure Enter the keyword secure to delete all its database and hardware flows/ resources, when the VTEP loses connectivity with the controller. non secure Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1687
local-vtep-ip Set the local IP Address to be used as the source IP for VXLAN tunnels. Syntax local-vtep-ip IP Address To disable the settings, use the no local-vtep-ip command. Parameters Defaults IP Address Enter the local IP Address to be used as a source for VXLAN tunnels. None. Command Modes VXLAN INSTANCE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1688
peer-ovsdbserver-ip Specify the IP address of the peer OVSDB server in a VLT setup. Syntax peer-ovsdbserver-ip peer-ip-address To remove the configuration, use the no peer-ovsdbserver-ip Parameters Defaults peer-ip-address Enter the peer OVSDB server IP address. This is usually the management IP address of the peer VLT device. Not configured Command Modes VXLAN-INSTANCE Command History This guide is platform-specific.
PAGE 1689
Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile. The range is from 1 to 16777215. None. Command Modes VNI-PROFILE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.
PAGE 1690
Defaults nuage Enter the keyword nuage to connect to a Nuage controller. static Enter the keyword static to configure static VXLANs. Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced nsx and Nuage keywords on the S5048F–ON. 9.13(0.
PAGE 1691
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.4(0.0) Introduced on the S6000. Usage Information You must disable vxlan-instance before unconfiguring VAP. Related Commands feature vxlan — Enable VXLAN configuration globally on the platform.
PAGE 1692
vxlan-vnid Associate VNID to VLAN. Syntax vxlan-vnid VNID To remove the association, use the no vxlan-vnid command. Parameters Defaults VNID Enter the logical network identifier. None Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.
PAGE 1693
no shutdown vni-profile ni1 vnid 1 remote-vtep-ip 2.2.2.2 vni-profile ni1 Controller Mode: DellEMC#show running-config vxlan ! feature vxlan ! vxlan-instance 1 gateway-ip 3.3.3.3 fail-mode secure controller 1 192.168.122.6 port 6632 ssl no shutdown Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance Displays information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1694
Port List Fo 1/49/1 Related Commands : Tf 1/16 Tf 1/20 Po 2 vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance logical network Displays logical network information related to Network Virtualization Overlay (NVO) Gateway. Syntax show vxlan vxlan-instance instance ID logical-network [name name] Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release.
PAGE 1695
show vxlan vxlan-instance physical-locator Displays physical locators related to Network Virtualization Overlay (NVO) Gateway. Syntax Parameters Defaults show vxlan vxlan-instance instance ID physical—locator [vtep-ip A.B.C.D] instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. A.B.C.D Enter the IP address of the VTEP. Disabled Command Modes VXLAN INSTANCE Command History Example Related Commands This guide is platform-specific.
PAGE 1696
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information. ● For a Port Channel, enter the keywords port-channel. VLAN-ID Defaults Enter the VLAN ID. Disabled Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1697
Example Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. DellEMC# show vxlan vxlan-instance 1 statistics remote-vtep-ip 1.1.1.1 Statistics for Remote-vtep-ip : 1.1.1.
PAGE 1698
Example DellEMC# show vxlan vxlan-instance <1> unicast-mac-local Total Local Mac Count: 5 VNI MAC PORT VLAN 4656 4656 4656 4656 4656 Related Commands 00:00:02:00:03:00 00:00:02:00:03:01 00:00:02:00:03:02 00:00:02:00:03:03 00:00:02:00:03:04 Tf Tf Tf Tf Tf 1/17 1/17 1/17 1/17 1/17 0 0 0 0 0 vxlan-instance- Enable VXLAN Instance configuration on the platform.
PAGE 1699
show vxlan vxlan-instance vtep-vni-map Displays information on VTEP to VNI mapping for a specific remote VTEP or all remote VTEPs Syntax Parameters show vxlan vxlan-instance instance ID vtep-vni-map remote-vtep-ip IPAddress instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. remote-vtep-ip Enter the keyword remote-vtep-ip followed by the IP address of the remote VTEP.
PAGE 1700
64 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1701
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1702
Usage Information Version Description 6.2.1.1 Introduced on the E-Series. The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax clear counters vrrp [vrrp-id] [ipv6] Parameters vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1703
● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as clear counters interfaces interface-type 1/1 - 4. ● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/ [subport].
PAGE 1704
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.
PAGE 1705
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. disable Disable a VRRP group. Syntax disable To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific.
PAGE 1706
hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router. By delaying the initialization of the VRRP MASTER, the new switch can stabilize its routing tables. Syntax hold-time {seconds | centisecs centisecs} To return to the default value, use the no hold-time command. Parameters seconds Enter the number of seconds. The range is from 0 to 65535. The default is zero (0) seconds. centisecs Enter the keyword centisecs then the number of centisecs in units of 25 centisecs.
PAGE 1707
To prohibit preemption, use the no preempt command. Defaults Enabled (that is, a BACKUP router can preempt the MASTER router). Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1708
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.16.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1709
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC(conf-if-vrid-4)# show config vrrp-group 4 virtual-address 119.192.182.124 ! DellEMC(conf-if-vrid-4)# show vrrp View the VRRP groups that are active. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group.
PAGE 1710
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1711
Usage Information The following describes the show vrrp command. Item Description TwentyfiveGigE.. Displays the interface, VRRP group ID, and network address. If the interface is not . sending VRRP packets, 0.0.0.0 appears as the network address. State: master... Displays the interface’s state: ● Na/If (not available) ● master (MASTER virtual router) ● backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:...
PAGE 1712
Up twentyFiveGigE 1/1 priority-cost 10 Up twentyFiveGigE 1/4 priority-cost 10 DellEMC> Example (VRRP VRF) DellEMC# show vrrp vrf jay -----------------fortyGigE 1/49/1, IPv4 VRID: 20, Version: 2, Net: 10.0.0.3 VRF: 1 jay State: Master, Priority: 100, Master: 10.0.0.3 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 38, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:14 Virtual IP address: 10.0.0.
PAGE 1713
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 7.6.1.0 Introduced on the S-Series (S50 only). 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1714
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when you configure a virtual IP address. When you delete the virtual address, the VRRP group stops sending VRRP packets. A system message appears after you enter or delete the virtual-address command.
PAGE 1715
vrrp delay reload Set the delay time for VRRP initialization after a system reboot. Syntax Parameters Defaults vrrp delay reload seconds seconds Enter the number of seconds for the delay. The frange is from 0 to 900 (0 indicates no delay). 0 Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.
PAGE 1716
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1717
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. You can use the both command to migrate from VRRPv2 to VRRPv3.
PAGE 1718
Parameters vrid (OPTIONAL) Enter the number of an IPv6 VRRP group; range is from 1 to 255. vrf vrf-name (OPTIONAL) Enter the name of a VRF instance to clear the counters of all IPv6 VRRP groups in the specified VRF. The maximum is 32 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON.
PAGE 1719
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port information.
PAGE 1720
show vrrp ipv6 View the active IPv6 VRRP groups. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group. Syntax show vrrp ipv6 [vrid] [interface] [brief] [vrf vrf-name] Parameters vrid (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255.
PAGE 1721
Line starting with Description GigabitEthernet.. Displays the interface, VRRP group ID, and network address. If the interface is not . sending VRRP packets, 0.0.0.0 appears as the network IP address. VRF VRF instance to which the VRRP group interface belongs. State: master... Displays the interface’s state: ● Na/If (not available) ● master (MASTER virtual router) ● backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:...
PAGE 1722
Parameters Defaults vrid Enter the virtual-router ID number of the VRRP group. The VRID range is from 1 to 255. Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1723
65 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1724
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax crypto ca-cert install path Parameters path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1725
Usage Information The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1726
device. If the Common Name does not match the device’s presented identity, then even a properly signed certificate does not validate correctly. email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect.
PAGE 1727
crypto cert install Installs a trusted certificate on a device. Syntax Parameters crypto cert install cert-file cert-path key-file {key-path | private} [password passphrase] cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored.
PAGE 1728
NOTE: It is possible for the switch to store two types of certificates: one for the FIPS mode and one for the non-FIPS mode. If the system is in FIPS mode, the certificate is installed as the FIPS certificate. If the system is in non-FIPS mode, the certificate is installed as the non-FIPS certificate. When FIPS mode is enabled or disabled, the certificates (and keys) are switched by the system. NOTE: For the switch, there are two possible certificates stored - one for FIPS mode, one for nonFIPS mode.
PAGE 1729
Parameters Defaults ocsp Enter the method used to check certificate revocation details. In this release, OCSP is the only option that is supported. So, you can specify OCSP as the method-list value. accept Enter the keyword accept to accept the presented certificate and log in if OCSP retrieval fails. reject Enter the keyword reject to reject the presented certificate and log in if OCSP retrieval fails.
PAGE 1730
logging secure Creates a log file for various events related to X.509v3 certificates. Syntax logging {hostname} {secure | tcp | udp} [vrf vrf-name] [sha1 fingerprint] [port port-number] Parameters hostname Enter the name of the host or device for which you wish to record logs corresponding to the certificates. NOTE: The hostname can be an IPV4 address, an IPV6 address, or a DNS hostname—with or without DNS suffix.
PAGE 1731
crypto x509 ca-keyid Creates a per-certificate configuration context using the specified subject key identifier. Syntax crypto x509 ca-keyid subject-key-identifier Use to the no crypto x509 ca-keyid command to remove this configuration. Parameters subject-keyidentifier Enter the content of the SubjectKeyIdentifier field from the CA certificate. NOTE: To get the subject key identifier details, enter the show crypto cacert command. This command displays the CA certificate details. Defaults None.
PAGE 1732
sign-requests Defaults Enter the keyword sign-requests to sign the OCSP requests to OCSP responder communication with the system’s own certificate so that the OCSP responder may verify the requestor. The sign-requests feature is off by default. The no version of the command disables signing of requests. None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1733
show crypto ca-cert Displays the certificate information corresponding to the root CA. Syntax show crypto ca-certs Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.11.0.