Users Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Table Of Contents

Dell Command Line Reference Guide for the

S4048–ON System

9.14.2.6

June 2020

Rev. A00

Summary of content (1786 pages)

PAGE 1
Dell Command Line Reference Guide for the S4048–ON System 9.14.2.6 June 2020 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide.........................................................................................................43 Objectives........................................................................................................................................................................... 43 Audience..............................................................................................................................................................................
PAGE 4
asf-mode..............................................................................................................................................................................87 banner exec........................................................................................................................................................................ 88 banner login....................................................................................................................................
PAGE 5
show environment........................................................................................................................................................... 135 show inventory................................................................................................................................................................. 136 show login statistics.......................................................................................................................................
PAGE 6
remark...........................................................................................................................................................................188 show config.................................................................................................................................................................190 Common IP ACL Commands.....................................................................................................................................
PAGE 7
continue.......................................................................................................................................................................246 description...................................................................................................................................................................247 match as-path..............................................................................................................................................
PAGE 8
deny ether-type (for Extended MAC ACLs)............................................................................................................ 287 deny (for Standard MAC ACLs)..................................................................................................................................289 deny (for Extended MAC ACLs)................................................................................................................................. 290 permit (for Standard IP ACLs).......
PAGE 9
show bfd neighbors........................................................................................................................................................ 343 vrrp bfd neighbor............................................................................................................................................................ 346 Chapter 9: Border Gateway Protocol......................................................................................... 348 BGP IPv4 Commands..............
PAGE 10
neighbor advertisement-interval........................................................................................................................... 388 neighbor advertisement-start................................................................................................................................ 389 neighbor allowas-in...................................................................................................................................................
PAGE 11
show ip bgp neighbors............................................................................................................................................. 440 show ip bgp next-hop.............................................................................................................................................. 444 show ip bgp paths.....................................................................................................................................................
PAGE 12
show ipv6 protocol-queue-mapping...........................................................................................................................483 show mac protocol-queue-mapping...........................................................................................................................484 Chapter 12: Data Center Bridging (DCB)....................................................................................486 DCB Command..........................................................
PAGE 13
show running-config dcb-buffer-threshold..............................................................................................................525 service-class buffer shared-threshold-weight........................................................................................................ 526 dcb pfc-queues................................................................................................................................................................527 dcb {ets | pfc} enable.....
PAGE 14
show ip dhcp server................................................................................................................................................. 569 Commands to Configure Secure DHCP.................................................................................................................... 570 arp inspection.............................................................................................................................................................
PAGE 15
fips mode enable............................................................................................................................................................. 606 show fips status.............................................................................................................................................................. 606 show ip ssh................................................................................................................................................
PAGE 16
Chapter 20: High Availability (HA).............................................................................................648 redundancy disable-auto-reboot................................................................................................................................. 648 redundancy force-failover............................................................................................................................................ 649 redundancy primary.............................
PAGE 17
errdisable recovery interval.................................................................................................................................... 687 flowcontrol..................................................................................................................................................................688 interface.................................................................................................................................................................
PAGE 18
Port Channel Commands...............................................................................................................................................747 channel-member........................................................................................................................................................ 747 group........................................................................................................................................................................
PAGE 19
ip domain-lookup............................................................................................................................................................. 790 ip domain-name............................................................................................................................................................... 790 ip helper-address...........................................................................................................................................
PAGE 20
ipv6 address autoconfig................................................................................................................................................ 846 ipv6 address..................................................................................................................................................................... 846 ipv6 address eui64............................................................................................................................................
PAGE 21
default-information originate....................................................................................................................................... 886 description........................................................................................................................................................................ 887 distance.......................................................................................................................................................
PAGE 22
show isis neighbors......................................................................................................................................................... 931 show isis protocol........................................................................................................................................................... 933 show isis traffic............................................................................................................................................
PAGE 23
fefd mode....................................................................................................................................................................975 fefd reset.................................................................................................................................................................... 976 fefd-global interval........................................................................................................................................
PAGE 24
debug ip msdp.................................................................................................................................................................1015 ip msdp cache-rejected-sa.......................................................................................................................................... 1015 ip msdp default-peer................................................................................................................................................
PAGE 25
show spanning-tree msti............................................................................................................................................. 1048 spanning-tree................................................................................................................................................................. 1050 spanning-tree msti................................................................................................................................................
PAGE 26
description.................................................................................................................................................................1086 show running-config track.................................................................................................................................... 1086 show track.................................................................................................................................................................
PAGE 27
ip ospf transmit-delay............................................................................................................................................. 1132 log-adjacency-changes........................................................................................................................................... 1133 maximum-paths........................................................................................................................................................
PAGE 28
ipv6 ospf dead-interval........................................................................................................................................... 1193 ipv6 ospf encryption................................................................................................................................................1194 ipv6 ospf graceful-restart helper-reject.............................................................................................................
PAGE 29
show ip pim interface............................................................................................................................................. 1239 show ip pim neighbor..............................................................................................................................................1240 show ip pim rp...........................................................................................................................................................
PAGE 30
extend system-id........................................................................................................................................................... 1279 protocol spanning-tree pvst....................................................................................................................................... 1280 show spanning-tree pvst..............................................................................................................................................
PAGE 31
show qos policy-map-input................................................................................................................................... 1326 show qos policy-map-output................................................................................................................................ 1327 show qos qos-policy-input.................................................................................................................................... 1328 show qos qos-policy-output.
PAGE 32
Chapter 48: Remote Monitoring (RMON)..................................................................................1371 rmon alarm....................................................................................................................................................................... 1371 rmon collection history................................................................................................................................................. 1373 rmon collection statistics......
PAGE 33
aaa authentication login.......................................................................................................................................... 1414 aaa reauthenticate enable...................................................................................................................................... 1416 access-class..............................................................................................................................................................
PAGE 34
dot1x authentication (Interface)..........................................................................................................................1454 dot1x auth-fail-vlan................................................................................................................................................. 1454 dot1x auth-server....................................................................................................................................................
PAGE 35
ip dhcp snooping vlan............................................................................................................................................. 1495 show ip dhcp snooping...........................................................................................................................................1496 Role-Based Access Control Commands..................................................................................................................
PAGE 36
snmp-server community........................................................................................................................................ 1533 snmp-server contact.............................................................................................................................................. 1534 snmp-server enable traps......................................................................................................................................
PAGE 37
stack-unit priority..........................................................................................................................................................1600 stack-unit provision...................................................................................................................................................... 1600 stack-unit stack-group........................................................................................................................................
PAGE 38
address.......................................................................................................................................................................1635 street-address..........................................................................................................................................................1636 territory.......................................................................................................................................................
PAGE 39
Chapter 62: Uplink Failure Detection (UFD)............................................................................. 1672 clear ufd-disable............................................................................................................................................................ 1672 debug uplink-state-group............................................................................................................................................ 1673 description...........................
PAGE 40
show vlt-proxy-gateway...............................................................................................................................................1710 Chapter 66: Virtual Link Trunking (VLT)................................................................................... 1712 back-up destination....................................................................................................................................................... 1713 clear vlt statistics..................
PAGE 41
vxlan-vnid........................................................................................................................................................................ 1746 show running-config vxlan.......................................................................................................................................... 1747 show vxlan vxlan-instance......................................................................................................................................
PAGE 42
show crypto ca-cert..................................................................................................................................................... 1785 show crypto cert...........................................................................................................................................................
PAGE 43
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 44
Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
PAGE 45
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 46
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 47
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/1 for the interface tengigabitethernet 1/1/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
PAGE 48
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
PAGE 49
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
PAGE 50
show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated the command to display the IPV6acloptimized feature on the S6100– ON and Z9100–ON. 9.12(1.
PAGE 51
To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command. CONFIGURATION Mode In EXEC Privilege mode, use the configure command to enter CONFIGURATION mode and configure routing protocols and access interfaces. To enter CONFIGURATION mode: 1. Verify that you are logged in to EXEC Privilege mode. 2.
PAGE 52
EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode.
PAGE 53
NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port[/subport] number.
PAGE 54
1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode. 2. Enter the protocol lldp command. The prompt changes to include conf-lldp or conf-if-interface-lldp. LLDP MANAGEMENT INTERFACE Mode To enable and configure Link Layer Discovery Protocol (LLDP) on management interfaces, use LLDP MANAGEMENT INTERFACE mode. To enter LLDP MANAGEMENT INTERFACE mode: 1. Verify that you are logged in to LLDP mode. 2.
PAGE 55
OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the openflow of-instance command, and then the OpenFlow ID number of the instance you want to create or configure. The prompt changes to include conf-of-instance of-id. You can return to the CONFIGURATION mode by entering the exit command.
PAGE 56
2. Enter the protocol spanning-tree rstp command. The prompt changes to include conf-rstp. You can return to CONFIGURATION mode by using the exit command. ROUTE-MAP Mode To configure a route map, use ROUTE-MAP mode. To enter ROUTE-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the route-map map-name [permit | deny] [sequence-number] command. The prompt changes to include config-route-map. You can return to CONFIGURATION mode by using the exit command.
PAGE 57
To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include conf-router_rip. You can return to CONFIGURATION mode by using the exit command. SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode. For more information, see Spanning Tree Protocol (STP). To enter SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 58
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 59
primary Enter the keyword primary to specify the primary Dell EMC Networking OS image. secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. system: Enter the keyword system: to use the system image file URL (system). ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system.
PAGE 60
cd Change to a different working directory. Syntax cd [flash: | usbflash:] Parameters flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB.
PAGE 61
Password to login remote host: Destination file name [sample_file]: Defaults None. Command Modes EXEC Privilege Command History Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. copy http://admin:admin123@10.16.206.77/sample_file flash://sample_file copy Copy one file to another location.
PAGE 62
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added the nfsmount: parameters that allow you to mount a remote NFS file system. 9.4(0.0) Added the compressed-config parameter. 9.3(0.1) Added the http parameter on the S6000, Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. 8.4.1.
PAGE 63
! 4080 bytes successfully copied DellEMC# In this copy scp: flash: example, specifying SCP in the first position indicates that you need to specify the target in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal flash. The source is on a secure server running secure shell (SSH), so you are prompted for the user datagram protocol (UDP) port of the SSH server on the remote host.
PAGE 64
usbflash: To delete a file or directory on the external USB flash, enter usbflash:// then the filename or directory name ([usbflash://]filepath). no-confirm (OPTIONAL) Enter the keywords no-confirm to specify that the Dell EMC Networking OS does not require user input for each file prior to deletion. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 65
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for NFS mount. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 66
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 67
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Introduced on S4810 and Z9000. 8.3.19.0 Introduced on S4820T. Include the colon (:) when entering this command. This command checks the specified flash memory for errors. If errors are found, the command recommends that you format the flash.
PAGE 68
Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system. username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password. Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 69
Example Related Commands DellEMC# rmdir nfsmount:/nfs-mountpoint/guest Proceed to remove the directory [confirm yes/no]: yes ● mkdir – create a directory. HTTP Copy via CLI Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). Syntax copy http://10.16.206.77/sample_file flash://sample_filecopy flash:// sample_file http://10.16.206.77/sample_file You can copy from the server to the switch and vice-versa.
PAGE 70
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 71
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fan-out, and so forth). When restoring all units in a stack, all the units in the stack are placed into stand-alone mode. When restoring a single unit in a stack, that unit placed in stand-alone mode.
PAGE 72
Example (single stack) Example (NvRAM all stack units) Example (NvRAM, single unit) DellEMC# restore factory-defaults stack-unit 1 clear-all ************************************************************** * Warning - Restoring factory defaults will delete the existing * * startup-config and all persistent settings (stacking, fanout, etc.)* * After restoration the unit(s) will be powercycled immediately.
PAGE 73
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 74
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. E-Series Original command. DellEMC# show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 75
Example Version Description 7.6.1.0 Introduced on the S-Series 7.5.1.0 Introduced on the C-Series E-Series Original command DellEMC#show file-systems Size(b) 4286574592 2032525312 DellEMC# Command Fields Free(b) 4170424320 590807040 - Feature Type FAT32 USERFLASH unformatted USERFLASH Unknown NFSMOUNT network network network network Flags rw rw rw rw rw rw rw Prefixes flash: fcmfs: nfsmount: ftp: tftp: scp: http: Field Description size(b) Lists the size (in bytes) of the storage location.
PAGE 76
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 77
fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current FVRP configuration gvrp for the current GVRP configuration host for the current host configuration hardwaremonitor for hardware-monitor action-on-error settings hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current interface configuration interface port-channel for the current port-chann
PAGE 78
qos-policyinput for the current input QoS policy configuration qos-policyoutput for the current output QoS policy configuration radius for the current RADIUS configuration redirect-list for the current redirect-list configuration redundancy for the current RPM redundancy configuration resolve for the current DNS configuration rip for the current RIP configuration rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configura
PAGE 79
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for the tunnel and EIS interface types. 9.0.0.0 Added support for the VLT option. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the hardware-monitor option. 7.6.1.
PAGE 80
show startup-config Display the startup configuration. Syntax show startup-config Command Modes EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 81
Command Modes EXEC Privilege Command History Command Fields This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 82
upgrade Upgrade the bootflash image or system image of the management unit. Syntax upgrade boot {all | bootflash—image | bootselector-image} stack-unit {stackunit-number | all} {booted | flash: | ftp: | nfsmount | scp: | tftp: | usbflash:} file-url Parameters boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image.
PAGE 83
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility this command accepts IPv6 host addresses with or without the square brackets. Reload Dell EMC Networking OS after executing this command.
PAGE 84
stack-unit stack- Enter the keyword stack-unit and specify the stack-unit ID to sync the image unit-id to that stack-unit. Defaults stack-unit all Enter the keyword stack-unit followed by the keyword all to sync the image on all stack-units. tftp: file-url Enter the keyword tftp: and specify the location of the image file in the format //host-ip/filepath or press Enter to launch a prompt sequence.
PAGE 85
1. Upgrade the system image to the new image and configure the primary partition to boot from the new image using the boot system command. 2. Update the startup configuration file with the new set of configurations and then reload the device using the reload command. The new set of configurations are parsed from the startup configuration file and applied to the NVRAM. During the system boot up, the new set of configurations are applied to the system from the updated NVRAM configurations.
PAGE 86
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
PAGE 87
• • • • • • • • • • • • • • • • • • • • • • show command-history show cpu-traffic-stats show debugging show environment show inventory show login statistics show memory show processes cpu show processes ipc flow-control show processes memory show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit telnet telnet-peer-stack-unit terminal length traceroute undebug all virtual-ip write asf-mode Enable alternate store and forward (ASF) mode and forward packets as soon as a threshol
PAGE 88
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P1) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information You must save the configuration and reload the system to implement ASF.
PAGE 89
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original Command After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
PAGE 90
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the acknowledgement keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 91
banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters Defaults c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator. The delineator is a percent character (%). No banner is configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 92
cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 93
Usage Information Version Description 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dual-qos. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 94
clear average-power Reset the average power and average power start time. Syntax clear average-power stack-unit {stack-unit-number} Parameters Defaults stack-unitnumber Enter the stack unit number. None Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 95
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode.
PAGE 96
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode. Syntax disable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of the Dell EMC Networking OS. The range is from 0 to 15.
PAGE 97
Version Description E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax Parameters Defaults do command command Enter an EXEC-level command. none Command Modes ● CONFIGURATION ● INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 98
System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Syntax enable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of Dell EMC Networking OS. The range is from 0 to 15. 15 Command Modes EXEC Command History This guide is platform-specific.
PAGE 99
enable cpu-clock-monitor Enables Intel CPU LPC (Low Pin Count) clock-failure monitoring. Syntax enable cpu-clock-monitor To disable this feature, use the no enable cpu-clock-monitor command. Parameters None Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 100
Usage Information Version Description 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. To enable polling and to configure the polling frequency, use this command. enable xfp-power-updates Enable 10–gigabit small form-factor pluggable (XFP) power updates for SNMP. Syntax enable xfp-power-updates interval seconds Parameters Defaults interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds.
PAGE 101
● ● ● ● ● ● ● ● Command History Related Commands ACCESS-LIST PREFIX-LIST AS-PATH ACL COMMUNITY-LIST ROUTER OSPF ROUTER RIP ROUTER ISIS ROUTER BGP This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 102
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 103
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 104
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 105
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 106
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 107
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The hostname is used in the prompt. ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command.
PAGE 108
Version Description 8.1.1.0 Introduced on E-Series 7.6.1.0 Support added for S-Series 7.5.1.0 Introduced on C-Series ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses.
PAGE 109
password Defaults Enter a string up to 40 characters as the password. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 110
● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 111
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 112
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Use this command to make the FTP clients VRF-aware. The VRF name that you specify is used by the FTP client to reach the FTP server. If no VRF name is specified, then the default VRF is used. ip telnet server enable Enable the Telnet server on the switch.
PAGE 113
ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF. Syntax ip telnet server vrf {vrf-name | any | management} To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters Defaults vrf-name Enter the vrf-name to specify the VRF that is used by the TELNET server. any Enter the keyword any to enable server from any VRF.
PAGE 114
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 115
To undo the TELENT client configuration, use the ip telnet [vrf vrf-name] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TELENT client. Disabled Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant FTOS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 116
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards. 8.2.1.0 Increased number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series.
PAGE 117
Related Commands ● ftp-server topdir — sets the directory to be used for incoming FTP connections. ● ftp-server username — sets a username and password for incoming FTP connections. line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line.
PAGE 118
login concurrent-session Configures the limit of concurrent sessions for each user on console and virtual terminal lines. Syntax login concurrent-session {limit number-of-sessions | clear—line enable} no login concurrent-session {limit number-of-sessions | clear—line enable} Parameters Defaults limit number-of- sessions Sets the number of concurrent sessions that any user can have on console and virtual terminal lines. The range is from 1 to 12 (10 VTY lines, one console, and one AUX line).
PAGE 119
Escape character is '^]'. Login: admin Password: Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.97 Clear existing session? [line number/Enter to cancel]: When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of your existing sessions. Close any of your existing sessions to log in to the system. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'.
PAGE 120
Usage Information Version Description 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. Only the system and security administrators can configure login activity tracking and view the login activity details of other users. If you enable user login statistics, the system displays the last successful login details of the current user, the details of any failed login attempts by others, and if the current user’s permissions have changed since the last login.
PAGE 121
motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 122
NOTE: The :: notation specifies successive hexadecimal fields of zeros. 122 count Enter the number of echo packets to be sent. The default is 5. ● number: from 1 to 2147483647 ● continuous: transmit echo request continuously datagram size Enter the ICMP datagram size. The range is from 36 to 15360 bytes. The default is 100. timeout Enter the interval to wait for an echo reply before timing out. The range is from 0 to 3600 seconds. The default is 2 seconds.
PAGE 123
Defaults None. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0)P5 Introduced on the S4048–ON. 9.8(0.
PAGE 124
Example (IPv4) Symbol Description M Could not fragment. ? Unknown packet type. & Packet lifetime exceeded. DellEMC# ping 172.31.1.255 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2 seconds: Reply to request 1 from 172.31.1.208 0 ms Reply to request 1 from 172.31.1.216 0 ms Reply to request 1 from 172.31.1.205 16 ms :: Reply to request 5 from 172.31.1.209 0 ms Reply to request 5 from 172.31.1.66 0 ms Reply to request 5 from 172.31.1.
PAGE 125
Version Description 9.10(0.0) Added the optional dell-diag and onie parameters. Introduced the no-confirm option. Usage Information 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 9.1(0.0) Added ‘conditional’ parameter. 8.3.19.
PAGE 126
The following example shows how to reload the system into ONIE prompt and enter the install mode directly: DellEMC#reload onie install Proceed with reload [confirm yes/no]: yes reload-type Allows you to configure the boot-type or secure-erase for the next reload. Syntax reload-type Parameters N/A Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 127
Example DellEMC(conf-reload-type)#boot-type warmboot DellEMC(conf-reload-type)#end Dell# secure-erase Allows you to perform an fstrim on the flash disk during the next reload. Syntax secure-erase To disable secure-erase, use the no secure-erase command. Defaults Enabled. Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 128
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series.
PAGE 129
Usage Information Version Description 9.14(1.5) Added support for UTC time format. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 130
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.
PAGE 131
-- Chassis Vlan Cam ACL -Current Settings(in block sizes) 1 block = 256 entries VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 -- stack-unit 1 -Current Settings(in block sizes) VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 show command-history Display a buffered log of all commands all users enter along with a time stamp.
PAGE 132
DellEMC(conf)#service timestamps log datetime DellEMC# show command-history [May 17 15:38:55]: CMD-(CLI):[service timestamps log datetime]by default from console [May 17 15:41:40]: CMD-(CLI):[write memory]by default from console - Repeated 1 time.
PAGE 133
show cpu-traffic-stats View the CPU traffic statistics. Syntax Parameters Defaults show cpu-traffic-stats [port number | all | cp ] port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568. all (OPTIONAL) Enter the keyword all to display traffic statistics on all the interfaces receiving traffic, sorted based on the traffic. cp (OPTIONAL) Enter the keyword cp to display traffic statistics on the specified CPU.
PAGE 134
Unicast:100, Multicast:0, Broadcast:0 Processor : RP1 --------------Received 62% traffic on TenGigabitEthernet 8/2 Total packets:500 LLC:0, SNAP:0, IP:500, ARP:0, other:0 Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on TenGigabitEthernet 8/1 Total packets:300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Processor : RP2 --------------No CPU traffic statistics. DellEMC# show debugging View a list of all enabled debugging processes.
PAGE 135
ICMP packet debugging is on for TenGigabitEthernet 5/1,5/2,5/4,5/6,5/8,5/10,5/12,5/14,5/16 DellEMC# show environment View system component status (for example, temperature or voltage). Syntax Parameters show environment [all | fan | pem | stack-unit unit-id | thermal-sensor ] all Enter the keyword all to view all components. fan Enter the keyword fan to view information on the fans. The output of this command is chassis-dependent.
PAGE 136
Unit Bay TrayStatus Fan0 Speed Fan1 Speed ---------------------------------------------------0 0 up up 6971 up 7072 0 1 up up 6971 up 7021 0 2 up up 7021 up 7021 Speed in RPM -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) Power AvgPower AvgPowerStartTime -------------------------------------------------------------------------------------1 1 up AC up 6960 48 31 14/4/2017 17:24 1 2 up AC up 6656 40 26 14/4/2017 17:24 -- Unit Environment Status -Unit Status Temp Voltage TempStatus -----------
PAGE 137
Command History Usage Information Example (S4048– ON) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000-ON, S6100, Z9500, S6010, and Z9100. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 138
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Related Commands 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49/1 49/2 49/3 49/4 50 51 52 53 54 SFP+ SFP+ SFP SFP+ SFP+ SFP+ QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 10GBASE-SR Media not present or Media not present or Media not present or 10GBASE-SR 1000BASE-LX 10GBASE-LRM 10GBASE-LR Media not present or Media not present or Media not present or Media not present or Media not pr
PAGE 139
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the successful-attempts keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500.
PAGE 140
Last login location: Line vty0 ( 10.16.127.145 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 3 Successful login attempt(s) in last 30 day(s): 2 ----------------------------------------------------------------------------------------------------------------------------------User: admin3 Last login time: 13:18:42 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 141
Parameters stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack unit ID to display memory information on the designated stack member. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 142
summary (OPTIONAL) Enter the keywordsummary to view CPU utilization of processes related to stack-unit processing. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 143
timerMgr 0xbad6e000 PM 0xbad85000 KP 0xbad9a000 evagt 0xbadb4000 ipc 0xbadc9000 sysReaper 0xbae22000 tme 50 5 10000 0.00% 0.00% 0.00% 0 1190 119 10000 0.00% 0.00% 0.00% 0 0 0 0 0.00% 0.00% 0.00% 0 30 3 10000 0.00% 0.00% 0.00% 0 10 1 10000 0.00% 0.00% 0.00% 0 60 6 10000 0.00% 0.00% 0.
PAGE 144
0x000001ad lacp 0x000004ba clish 0x000000c9 nvmgr 0x000000e0 igmp 0x00000132 vrrp 0x0000028d ovsdbsvr 0x000000a9 arpm 0x00000253 otm 0x00000206 tnlmgr 0x00000012 mount_mfs 0x0000024d xstp DellEMC# Related Commands 520 52 10000 0.20% 0.30% 0.16% 0 330 33 10000 0.20% 0.36% 0.09% 0 1240 124 10000 0.20% 0.15% 0.44% 0 530 53 10000 0.20% 0.12% 0.16% 0 420 42 10000 0.20% 0.10% 0.13% 0 410 41 10000 0.20% 0.05% 0.12% 0 200 20 10000 0.20% 0.03% 0.
PAGE 145
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 146
IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFAGT3 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 IFMGR0 PORTMIRR0 IFMGR0 IFMGR0 DellEMC# IPSECMGR0 DHCP0 IPMGR0 IFAGT3 IFMGR0 OFMGR0 ACL0 VRRP0 PIM0 MACMGR0 L2PM0 DIFFSERV0 RTM0 LLDP0 MRTM0 IPMGR1 LACP0 ACL_AGENT2 IGMP0 IFAGT2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 8 29 1 1 16 8 10 1 0 29 51 9 12 10 33 23 0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 11 11 36 2 1 21 14 17 1 0 40 67 11 12 10 33 23
PAGE 147
Usage Information show processes memory output Field Description Total: Total system memory available MaxUsed: Total maximum memory used ever (history indicated with time stamp) CurrentUsed: Total memory currently in use CurrentFree: Total system memory available SharedUsed: Total used shared memory SharedFree: Total free shared memory PID Process ID Process Process Name ResSize Actual resident size of the process in memory Size Process test, stack, and data size Allocs Total dynamic
PAGE 148
314 igmp 4960256 380928 18588 16564 313 mrtm 6742016 1130496 72758 0 308 l2mgr 5607424 552960 735214 380972 301 l2pm 5001216 167936 1429522 1176044 298 arpm 4628480 217088 71092 33128 294 ospf 5468160 503808 724204 662560 288 dsm 6778880 1159168 39490 16564 287 rtm 5713920 602112 442280 198768 284 rip 4562944 258048 528 0 281 lacp 4673536 266240 221060 0 277 ipm1 4837376 380928 83788 0 273 acl 5005312 512000 239564 149076 272 topoDPC 117927936 0 0 0 271 bcmNHOP 117927936 0 0 0 270 bcmDISC 117927936 0 0 0 26
PAGE 149
Example — System reboot for unknown reasons DellEMC# show reset-reason Cause: N/A Reload Time: N/A Example — The example shows the reason for the last reboot as N/A for warm reset. System reboot due to power loss DellEMC#show reset-reason or pressing the Cause : N/A Reset Time : N/A. power button off and on. Example — System reboot due to watchdog timeout Example — System reboot due to thermal shutdown DellEMC#show reset-reason Cause: N/A.
PAGE 150
ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics. ifcb interface Enter the keyword ifcb then one of the following interface IDs then the interface information to display interface control block information for that interface: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 151
Unidentified Client0 0x006e0002 0x00000000 0x00000000 0x00000000 0 DellEMC# show system Display the status of all stack members or a specific member. Syntax Parameters show system [brief | stack-unit unit-id] brief (OPTIONAL) Enter the keyword brief to view an abbreviated list of system information. stack-unit unit-id (OPTIONAL) Enter the keywords stack-unit then the stack member ID for information on t stack member. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 152
-- Unit 1 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S4048-ON - 54-port TE/FG (SK-ON) Current Type : S4048-ON - 54-port TE/FG (SK-ON) Master priority : 0 Hardware Rev : 2.0 Num Ports : 72 Up Time : 2 day, 20 hr, 49 min Dell EMC Networking OS Version : 9.13(0.0) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : 3.21.2.9 Boot Selector : 3.21.0.
PAGE 153
flash: Save to local flash drive (flash://filename. A maximum of 20 characters. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated to display the show revision and show os-version command outputs. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 154
● ● ● ● Example (options under show techsupport) show show show show Inventory log summary command-history (last 20 commands) log DellEMC# show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command DellEMC#show tech-support stack-unit 1 ? | Pipe through a command DellEMC# show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence of a pattern grep Show only text that matches a pattern no-more Don'
PAGE 155
--------------------------------------------------------------------Type Version Target checksum runtime 9.14(0.0) Control Processor passed BOOT IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target checksum boot flash 3.21.2.9 Control Processor passed BOOTSEL IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target checksum boot selector 3.21.0.
PAGE 156
Parameters Defaults -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 157
● For a Null interface, enter the keyword null then the Null interface number. ● For a port channel interface, enter the keywords port-channel then a number. ● For Tunnel interface types, enter the keyword tunnel then the slot/ port information. The range is from 1 to 16383. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 158
telnet-peer-stack-unit Open a Telnet connection to the peer stack unit. Syntax telnet-peer-stack-unit Defaults Not configured. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 159
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 160
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series with IPv6. 8.1.1.0 Introduced on the E-Series (IPv4 only). 7.9.1.0 Introduced VRF. 7.6.1.
PAGE 161
DellEMC#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 3ffe:501:ffff:100:201:e8ff:fe00:4c8b, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 3ffe:501:ffff:100:201:e8ff:fe00:4c8b 000.000 ms 000.000 ms 000.000 ms DellEMC# Related Commands ● ping — tests the connectivity to a device. undebug all Disable all debug operations on the system.
PAGE 162
virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6-address} command. Parameters ipv4-address Enter the IP address of the active management interface in a dotted decimal format (A.B.C.D.). ipv6-address Enter an IPv6 address of the active management interface, in the x:x:x:x::x format.
PAGE 163
write Copy the current configuration to either the startup-configuration file or the terminal. Syntax Parameters write [memory [compressed] | terminal] memory Enter the keyword memory to copy the current running configuration to the startup configuration file. This command is similar to the copy running-config startup-config command. compressed Enter the keyword compressed to write the operating configuration to the startup-config file in the compressed mode.
PAGE 164
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 165
• • • • • dot1x mac show show show tx-period dot1x cos-mapping interface dot1x interface dot1x profile debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x.
PAGE 166
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3.
PAGE 167
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 168
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: ● Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). ● Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command).
PAGE 169
Related Commands ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 170
Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9000 Series.
PAGE 171
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 172
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 173
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series.
PAGE 174
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode.
PAGE 175
Parameters Defaults force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. None Command Modes Auto Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 176
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9010. The dot1x profile command configures a dot1x profile to define a list of trusted supplicant MAC addresses. Maximum number of dot1x profiles is limited to 10.
PAGE 177
dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command. Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which reauthentication is initiated. The range is from 1 to 31536000 (one year). The default is 3600 (1 hour).
PAGE 178
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 179
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. When you configure the dot1x server-timeout value, take into account the communication medium used to communicate with an authentication server and the number of RADIUS servers configured.
PAGE 180
● Ensure that no configured profile exists at the time of configuring the static-mab command. ● Use this command in Interface Batch Mode to enable static MAB in a dual-homing setup. Example DellEMC(conf)#do show dot1x interface twentyFiveGigE 1/41 802.
PAGE 181
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command.
PAGE 182
mac Configure a list of supplicant MAC addresses for dot1x profile represented with a profile-name. Syntax [no] mac {mac-address1 mac-address2… mac-address6} Parameters Defaults mac-address1 mac-address2 … mac-address6 Enter the keyword mac and type the 48– bit MAC addresses using the H.H.H format. A maximum of 6 MAC addresses are allowed. None Command Modes DOT1X PROFILE CONFIG (conf-dot1x-profile) CONFIGURATION TERMINAL BATCH Command History Usage Information This guide is platform-specific.
PAGE 183
Command Modes ● EXEC ● EXEC privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 184
4 5 6 7 DellEMC# 3 2 1 0 show dot1x interface Display the 802.1X configuration of an interface. Syntax show dot1x interface interface [mac-address mac-address] Parameters Defaults interface Enter one of the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 185
802.
PAGE 186
Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: DellEMC# AUTHORIZED(GUEST
PAGE 187
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 188
• • • • • • • • • • • • • permit tcp (for Extended IP ACLs) seq arp (for Extended MAC ACLs) seq ether-type (for Extended MAC ACLs) seq (for IP ACLs) seq (for IPv6 ACLs) permit udp (for IPv6 ACLs) permit tcp (for IPv6 ACLs) permit icmp (for IPv6 ACLs) permit (for IPv6 ACLs) deny udp (for IPv6 ACLs) deny tcp (for IPv6 ACLs) deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
PAGE 189
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode.
PAGE 190
Related Commands ● show config — display the current ACL configuration. show config Display the current ACL configuration. Syntax show config Command Modes ● ● ● ● Command History Example 190 CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 191
Common IP ACL Commands The following commands are available within both Ingress and Egress IP ACL modes (Standard and Extended) and do not have mode-specific options. When an ACL is created without a rule and then is applied to an interface, ACL behavior reflects an implicit permit. The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line.
PAGE 192
Usage Information When you use the access-class access-list-name command without specifying the ipv4 or ipv6 attribute, both IPv4 as well as IPv6 rules that are defined in that ACL are applied to the terminal. This method is a generic way of configuring access restrictions. To be able to filter access exclusively using either IPv4 or IPv6 rules, use either the ipv4 or ipv6 attribute along with the access-class access-list-name command.
PAGE 193
ip access-group Assign an IP access list (IP ACL) to an interface. Syntax ip access-group access-list-name {in | out} [implicit-permit] [vlan vlanid] [layer3] [vrf vrf-name] To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id][layer3] [vrf vrf-name] command. Parameters Defaults access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic.
PAGE 194
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. You can assign one ingress ACL and one egress ACL to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces.
PAGE 195
Related Commands Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T–ON, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, and Z9500. ● ip access-list standard — configure a standard ACL. ● ip access-list extended — configure an extended ACL. ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 196
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. in | out Identify whether ACL is applied on the ingress or egress side. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to view the IP accounting information on either a default or a non-default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 196 This guide is platform-specific.
PAGE 197
Example DellEMC# show ip accounting access-list L3-ACL vrf vrf3 ! Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1.2.0/24 any negotiate 150 monitor 300 count (0 packets) seq 10 permit 20.1.2.0/24 seq 15 permit 30.1.2.0/24 DellEMC# show ip access-lists Display all of the IP ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/ mismatches against each ACL entry displayed.
PAGE 198
deny To drop packets with a certain IP address, configure a filter. Syntax deny {source | any | host {ip-address}} [count [bytes] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command.
PAGE 199
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 200
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 201
Defaults dscp (OPTIONAL) Enter the keyword dcsp to match the IP DSCP values. The range is from 0 to 63. ecn (OPTIONAL) Enter the keyword ecn to match the ECN bits. The range is from 0 to 3. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255).
PAGE 202
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide. Related Commands ● deny — assign a IP ACL filter to deny IP packets. ● ip access-list standard — create a standard ACL. resequence access-list Re-assign sequence numbers to entries of an existing access-list.
PAGE 203
seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ipaddress}} [count [byte] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To delete a filter, use the no seq sequence-number command. Parameters Defaults sequencenumber Enter a number from 0 to 4294967290. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.
PAGE 204
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 205
deny Configure a filter that drops IP packets meeting the filter criteria. Syntax deny {ip | ip-protocol-number} {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator][count [byte] | log] [dscp value] [order] [monitor] [fragments] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 206
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 207
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator] [dscp] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 208
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(2.0P0) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 209
mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255.
PAGE 210
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see Flow-based Monitoring in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 211
NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry. The range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range.
PAGE 212
● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults dscp Enter this keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63.
PAGE 213
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 214
Related Commands ● deny — assign a filter to deny IP traffic. ● deny tcp — assign a filter to deny TCP traffic. ip access-list extended Name (or select) an extended IP access list (IP ACL) based on IP addresses or protocols. Syntax ip access-list extended access-list-name To delete an access list, use the no ip access-list extended access-list-name command. Parameters Defaults access-list-name Enter a string up to 140 characters long as the access list name.
PAGE 215
permit To pass IP packets meeting the filter criteria, configure a filter. Syntax permit {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator] [count [bytes]] [dscp value] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
PAGE 216
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 217
● Use the no permit tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 218
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments.
PAGE 219
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes increment.
PAGE 220
Defaults host ip-address Enter the keyword host and then enter the IP address to specify a host IP address. ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 221
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 222
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. DellEMC# Data Mask 1 0000000000000000 1111110000000000 0 From To #Covered 1023 1024 Total Ports: 1024 Related Commands ● ip access-list extended — create an extended ACL. ● permit — assign a permit filter for IP packets. ● permit tcp — assign a permit filter for TCP packets. resequence access-list Re-assign sequence numbers to entries of an existing access-list.
PAGE 223
Usage Information When all sequence numbers are exhausted, this feature permits re-assigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 224
Defaults operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 225
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 226
clear counters mac access-group Clear counters for all or a specific MAC ACL. Syntax clear counters mac access-group [mac-list-name] Parameters mac-list-name (OPTIONAL) Enter the name of a configured MAC access list. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 227
out Enter the keyword out to configure the ACL to filter outgoing traffic. NOTE: 1. If the MAC ACL is applied on VLAN, none of the VLAN members should have an access list applied for that VLAN. 2. If the MAC ACL is applied on a Physical or Port Channel interface, the VLAN in which this port is associated should not have an access list applied. 3. If the MAC ACL is applied on a VLAN, then that VLAN should not belong to VLAN ACL group. 4.
PAGE 228
show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed. Syntax show mac access-lists [access-list-name] [interface interface] [in | out] Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters.
PAGE 229
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. in | out Identify whether ACL is applied on ingress or egress side.
PAGE 230
Standard MAC ACL Commands When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. These commands configure standard MAC ACLs and support both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets with a the MAC address specified, configure a filter.
PAGE 231
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 232
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Dell EMC Networking OS supports one ingress and one egress MAC ACL per interface. The number of entries allowed per ACL is hardware-dependent. For detailed specifications about entries allowed per ACL, see your line card documentation. NOTE: Ingress ACLs are supported on C-Series and S-Series platforms only.
PAGE 233
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 234
Defaults log (OPTIONAL) Enter the keyword log to include ACL messages in the log. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated.
PAGE 235
Extended MAC ACL Commands When an access-list is created without any rule and then applied to an interface, ACL behavior reflects implicit permit. The following commands configure Extended MAC ACLs. The platform supports both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets that match the filter criteria, configure a filter.
PAGE 236
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 237
Parameters access-list-name Enter a text string as the MAC access list name, up to 140 characters. cpu-qos Defaults Enter the keywords cpu-qos to assign this ACL to control plane traffic only (CoPP). None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 238
seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands ● mac access-list standard — configure a standard MAC access list. ● show mac accounting access-list — display MAC access list configurations and counters (if configured). permit To pass packets matching the criteria specified, configure a filter.
PAGE 239
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 240
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 241
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 242
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 243
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 244
Example Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf-nprefixl)# show config ! ip prefix-list snickers DellEMC(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. Syntax show ip prefix-list detail [prefix-name] Parameters prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters.
PAGE 245
ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 seq 5 permit 1.1.1.0/24 (hit count: 0) seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) DellEMC# show ip prefix-list summary Display a summary of the configured prefix lists. Syntax Parameters show ip prefix-list summary [prefix-name] prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters.
PAGE 246
Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit. To configure route maps and their redistribution criteria, use the following commands. continue To a route-map entry with a higher sequence number, configure a route-map. Syntax continue [sequence-number] Parameters Defaults sequencenumber (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Not configured.
PAGE 247
● If the next route map entry does not contain a continue clause, the route map evaluates normally. If a match does not occur, the route map does not continue and falls through to the next sequence number, if one exists. Set Clause with Continue Clause If the route-map entry contains sets with the continue clause, set actions are performed first then the continue clause jumps to the specified route map entry.
PAGE 248
To delete a match AS path filter, use the no match as-path as-path-name command. Parameters Defaults as-path-name Enter the name of an established AS-PATH ACL, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 249
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 250
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 251
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 252
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 253
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 254
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address.
PAGE 255
Version Description 8.1.1.0 Introduced on the E-Series. pre-6.1.1.0 Introduced on the E-Series. match route-type To match routes based on the how the route is defined, configure a filter. Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command.
PAGE 256
Related Commands ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address. ip route-source — redistribute routes that match routes advertised by other routers. metric — redistribute routes that match a specific metric. tag — redistribute routes that match a specific tag.
PAGE 257
route-map Enable a route map statement and configure its action and sequence number. This command also places you in ROUTE-MAP mode. Syntax route-map map-name [permit | deny] [sequence-number] To delete a route map, use the no route-map map-name [permit | deny] [sequencenumber] command. Parameters Defaults map-name Enter a text string of up to 140 characters to name the route map for easy identification. permit (OPTIONAL) Enter the keyword permit to set the route map default as permit.
PAGE 258
Example Related Commands DellEMC(conf)# route-map dempsey DellEMC(config-route-map)# ● show config — display the current configuration. set as-path To modify the AS path for border gateway protocol (BGP) routes, configure a filter. Syntax set as-path prepend as-number [... as-number] To remove an AS-Path setting, use the no set as-path {prepend as-number | tag} command.
PAGE 259
set automatic-tag To automatically compute the tag value of the route, configure a filter. Syntax set automatic-tag To return to the default, enter no set automatic-tag. Defaults Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 260
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 261
no-advertise Enter the keywords no-advertise to drop all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to drop all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary.
PAGE 262
Parameters Defaults backbone Enter the keyword backbone to redistribute matched routes to the OSPF backbone area (area 0.0.0.0). level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Not configured.
PAGE 263
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 264
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 265
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 266
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you configure the set next-hop command, its configuration takes precedence over the neighbor next-hop-self command in the ROUTER BGP mode.
PAGE 267
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command. Parameters Defaults tag-value Enter a number as the tag. The range is from zero (0) to 4294967295.
PAGE 268
set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Syntax set weight weight To delete a weight specification, use the no set weight weight command. Parameters weight Enter a number as the weight used by the route meeting the route map specification. The range is from 0 to 65535. The default is router-originated = 32768 and all other routes = 0.
PAGE 269
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 270
Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 271
Usage Information Example Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series. To apply the AS-PATH ACL to BGP routes, use the match as-path or neighbor filter-list commands.
PAGE 272
IP Community List Commands IP community list commands are supported on the Dell EMC Networking OS. ip community-list Enter COMMUNITY-LIST mode and create an IP community-list for BGP. Syntax ip community-list comm-list-name To delete a community-list, use the no ip community-list comm-list-name command. Parameters comm-list-name Enter a text string as the name of the community-list, up to 140 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 273
Example Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 274
Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. ip access-list standard — configures a standard ACL. ip access-list extended — creates an extended ACL. feature udf-acl Enable udf-acl feature on a switch. Syntax feature udf-acl To disable the udf-acl feature, use the no feature udf-acl command. Defaults Disabled Command Modes CONFIGURATION Example Command History Dell(conf)#feature udf-acl This guide is platform-specific.
PAGE 275
Example Command History Dell(conf-udf-tcam)#key innerL3header udf-id 6 packetbase innerL3Header offset 0 length 2 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. udf-tcam — creates a context for UDF TCAM.
PAGE 276
permit ip Associate the UDF in IP access-list. Syntax permit ip {source mask | any | host ip-address} {destination mask | any | host ip-address} udf-pkt-format name udf-qualifier-value name To remove this filter, use the no seq sequence-number command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous.
PAGE 277
! key innerL3header udf-id 6 packetbase innerL3Header offset 0 length 2 match l2ethertype ipv4 ipprotocol 4 vlantag any udf-qualifier-value ipnip_val1 Dell(conf-udf-tcam)# udf-id Assign value for each configured UDF ID in the given UDF TCAM profile. Syntax udf-id id value mask To return to the default settings, use the no udf-id 1-12 value mask command. Parameters Defaults id Enter the UDF ID range. The range is from 1 to 12. value Enter the value for the UDF in Hex, up to 24 bytes.
PAGE 278
Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. udf-id — assigns value for each configured UDF ID in the given UDF TCAM profile. udf-tcam — creates a context for UDF TCAM. show config — displays the current UDF-Qualifier-Value Profile configuration. udf-tcam Create a context for UDF TCAM. Syntax udf-tcam name seq number To return to the default settings, use the no udf-tcam name seq number command.
PAGE 279
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 280
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {ip | ip-protocol-number} {source mask | any | host ipaddress} {destination mask | any | host ip-address} command. Parameters Defaults ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255.
PAGE 281
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 282
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 283
● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 284
specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands ● deny — assign a filter to deny IP traffic. ● deny udp — assign a filter to deny UDP traffic. deny udp (for Extended IP ACLs) To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 285
Usage Information Version Description 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 286
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 287
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes.
PAGE 288
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny ether-type protocol-type-number {destination-mac-address mac-address-mask | any} vlan vlan-id {source-mac-address mac-address-mask | any} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 289
deny (for Standard MAC ACLs) To drop packets with a the MAC address specified, configure a filter. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]][monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {any | mac-source-address mac-source-address-mask} command.
PAGE 290
that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 291
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 292
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 293
which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 294
● Use the no permit ether-type protocol-type-number {destination-mac-address mac-address-mask | any} vlan vlan-id {source-mac-address mac-address-mask | any} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated.
PAGE 295
permit icmp (for Extended IP ACLs) Configure a filter to allow all or specific ICMP messages. Syntax permit icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator] [dscp] [count [byte]] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 296
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 297
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 298
permit (for Extended IP ACLs) To pass IP packets meeting the filter criteria, configure a filter. Syntax permit {source mask | any | host ip-address} {destination mask | any | host ip-address} [count [bytes]] [ttl operator] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 299
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added the support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 300
The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 301
which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 302
permit tcp (for Extended IP ACLs) To pass TCP packets meeting the filter criteria, configure a filter. Syntax permit tcp {source mask | any | host ip-address} [bit] [operator port [port]] {destination mask | any | host ip-address} [bit] [ttl operator] [dscp] [operator port [port]] [count [byte]] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 303
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 304
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled.
PAGE 305
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. You can enter a threshold in the range of 1-100.
PAGE 306
| host ip-address} [operator port [port]] [ttl operator] [count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] Parameters Defaults ttl Enter the keyword ttl to permit or deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value.
PAGE 307
and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 308
● lt = less than ● range = inclusive range of ports (you must specify two ports for the port parameter.) portnumber (OPTIONAL) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● 23 = Telnet ● 20 and 21 = FTP-DATA and FTP ● 25 = SMTP ● 169 = SNMP Defaults destination Enter the IP address of the network or host to which the packets are sent.
PAGE 309
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 310
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 311
Parameters source address mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all routes are subject to the filter. host ipv6- Enter the keyword host then the IP address to specify a host IP address. address destination address Enter the IPv6 address of the network or host to which the packets are sent.
PAGE 312
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific.
PAGE 313
permit icmp (for IPv6 ACLs) To allow all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax permit icmp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [message-type] [ttl operator] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 314
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P1) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 315
which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 316
deny udp (for IPv6 ACLs) Configure a filter to drop user datagram protocol (UDP) packets meeting the filter criteria.
PAGE 317
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms.
PAGE 318
● ● ● ● psh: rst: syn: urg: push function reset the connection synchronize sequence numbers urgent field operator (OPTIONAL) Enter one of the following logical operand: ● eq = equal to ● neq = not equal to ● gt = greater than ● lt = less than ● range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 319
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P0) Added the established parameter on the on the S6000, S6000–ON, S6100– ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON.
PAGE 320
Parameters source address mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip- Enter the keyword host then the IPv6 address to specify a host IP address. v6address Defaults destination Enter the IP address of the network or host to which the packets are sent.
PAGE 321
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.5(0.1) Introduced on the Z9500. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 322
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 323
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements. Topics: • • • • • • • • • • member vlan ip access-group show acl-vlan-group show cam-acl-vlan cam-acl-vlan show cam-usage show running config acl-vlan-group acl-vlan-group show acl-vlan-group detail description (ACL VLAN Group) member vlan Add VLAN members to an ACL VLAN group.
PAGE 324
Attaching an ACL individually to VLAN interfaces is similar to the behavior of ACL-VLAN mapping storage in CAM prior to the implementation of the ACL VLAN group functionality. ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax ip access-group {group name} out implicit-permit Parameters Default group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 325
Version Description 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
PAGE 326
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage. During the initialization of CAM, the chassis manager reads the NVRAM and allocates the dynamic VCAP regions.
PAGE 327
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S4810 and Z9000 platforms.
PAGE 328
Example 1: Output of the show cam-usage Command 328 Field Description Total CAM Total amount of space in the CAM block Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs DellEMC#show cam-usage Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM | Available CAM ========|========|=================|=============|=============| ============== 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | IN-L3 ACL | 1024 | 1 | 1023
PAGE 329
Example 2: Output of the show cam-usage acl Command Example 3: Output of the show cam-usage router Command DellEMC#show cam-usage acl Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM | Available CAM ========|========|=================|=============|=============| ============== 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | IN-L3 ACL | 1024 | 1 | 1023 | | IN-V6 ACL | 0 | 0 | 0 | | OUT-L2 ACL | 206 | 9 | 197 | | OUT-L3 ACL | 178 | 9 | 169 | | OUT-V6 ACL | 178 | 4 | 174 2 | 0 | IN-L2 ACL | 1536 | 0 | 1536
PAGE 330
| | IN-L3 ACL | 1024 | | | IN-V6 ACL | 0 | | | OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | Codes: * - cam usage is above 90%.
PAGE 331
DellEMC#show running-config acl-vlan-group ! acl-vlan-group Test member vlan 1-100 ip access-group test in DellEMC# Test acl-vlan-group Create an ACL VLAN group. Syntax acl-vlan-group {group name} To remove an ACL VLAN group, use the no acl-vlan-group {group name} command. Parameters Default group-name Specify the name of the ACL VLAN group. The name can contain a maximum 140 characters.
PAGE 332
Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information The output for this command displays in a line-by-line format.
PAGE 333
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 334
ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
PAGE 335
You can only enable BFD for VRRP in INTERFACE command mode (vrrp bfd all-neighbors). You can enable BFD on both default and nondefault VRFs for OSPF and BGP protocols for both IPv4 and IPv6 neighbors. NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd enable (Configuration) Enable BFD on all interfaces. Syntax bfd enable Disable BFD using the no bfd enable command. Defaults BFD is disabled by default.
PAGE 336
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd interval Specify non-default BFD session parameters beginning with the transmission interval.
PAGE 337
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC(conf-if-te-1/3)# bfd interval 250 min_rx 300 multiplier 4 role passive DellEMC(conf-if-te-1/3)# bfd protocol-liveness Enable the BFD protocol liveness feature.
PAGE 338
To disable BFD for all neighbors configured through static routes, use the no ip route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command. Parameters prefix-list prefix- (Optional) Enter the keyword prefix-list followed by the name of the prefix list-name list to enable or disable BFD on specific neighbors.
PAGE 339
ip ospf bfd all-neighbors Establish BFD sessions with all OSPF neighbors on a single interface or use non-default BFD session parameters. Syntax ip ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPF interface implicitly, use the no ip ospf bfd allneighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
PAGE 340
ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters. Syntax ipv6 ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPFv3 interface implicitly, use the no ipv6 ospf bfd allneighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
PAGE 341
ipv6 route bfd Enable BFD for all IPv6 neighbors configured through static routes. Syntax ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] To disable BFD for all IPv6 neighbors configured through static routes, use the no ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command.
PAGE 342
To remove all BFD sessions with IS-IS neighbors discovered on this interface, use the no isis bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] command. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface. interval (OPTIONAL) Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200.
PAGE 343
Parameters ip-address Enter the IP address of the BGP neighbor that you want to explicitly disable for BFD sessions in dotted decimal format (A.B.C.D). peer-group-name Enter the name of the peer group that you want to explicitly disable for BFD sessions. Defaults None Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 344
Defaults interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 345
VT - Vxlan Tunnel LocalAddr * 5.1.1.1 * 6.1.1.1 * 7.1.1.1 RemoteAddr 5.1.1.2 6.1.1.2 7.1.1.2 Interface Po 30 Vl 30 Te 1/21 State Up Up Up Rx-int 200 200 200 Tx-int 200 200 200 Mult 3 3 3 Clients O O O The following example shows the show bfd vrf neighbors command output showing the nondefault VRF. DellEMC(conf)#do sho bfd vrf vrf2 neighbors * Ad Dn B C I O O3 R M V VT - Active session role Admin Down BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr VRF Clients * 13.
PAGE 346
Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 6.1.1.
PAGE 347
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.
PAGE 348
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 349
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 350
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 351
Defaults Disabled Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 352
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
PAGE 353
bgp asnotation asdot DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process.
PAGE 354
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipathrelax command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 355
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The software compares the MEDs only if the path contains no external autonomous system numbers.
PAGE 356
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 357
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 358
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster.
PAGE 359
The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation. Dell EMC Networking OS accepts confederation EBGP peers without a LOCAL_PREF attribute. The software sends AS_CONFED_SET and accepts AS_CONFED_SET and AS_CONF_SEQ.
PAGE 360
Usage Information All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. After specifying autonomous systems numbers for the BGP confederation, recycle the peers to update their configuration. Related Commands ● bgp confederation identifier — configure a confederation ID.
PAGE 361
max-suppresstime (OPTIONAL) Enter the maximum number of minutes a route can be suppressed. The default is four times the half-life value. The range is from 1 to 255. The default is 60 minutes. route-map map- (OPTIONAL) Enter the keyword route-map then the name of a configured route map. name Only match commands in the configured route map are supported. Defaults Disabled. Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History Usage Information This guide is platform-specific.
PAGE 362
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 363
Link Bandwidth has to be configured on the router to tell it to associate Link Bandwidth with prefixes (paths) and/or to use Link Bandwidth in BGP Multipath route selection. This is done under BGP configuration and is supported per address family – for IPv4 and IPv6 address families. The configuration for a particular address family applies across all VRFs configured.
PAGE 364
bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails. Syntax bgp fast-external-fallover To disable fast external fallover, use the no bgp fast-external-fallover command. Defaults Enabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 365
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 366
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 367
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive.
PAGE 368
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 369
Usage Information After configuring the bgp redistribute-internal command, use the clear ip bgp * command to clear all BGP sessions. If you don’t clear all BGP sessions, route redistribution happens only for new routes. NOTE: When you enable redistribution of iBGP routes into an IGP, ensure that you use route maps to control what prefixes are redistributed. Redistributing all iBGP routes can create a loop in the network.
PAGE 370
configuration, filtering millions of routes based on regular expressions can be quite CPU intensive, as a regular expression evaluation involves generation and evaluation of complex finite state machines. BGP policies, containing regular expressions to match as-path and communities, tend to use much CPU processing time, which in turn affects the BGP routing convergence. Additionally, the show bgp commands, which are filtered through regular expressions, use up CPU cycles particularly with large databases.
PAGE 371
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessions.
PAGE 372
Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 373
ipv6–address mask (OPTIONAL) Enter the IPv6 address and the network mask to clear information on IPv6 route dampening. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 374
ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to clear information related only to ipv6 unicast routes. ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to reset only that prefix. ipv6–address mask (OPTIONAL) Enter the IPv6 address followed by the network mask to reset only that prefix. filter-list as- (OPTIONAL) Enter the keywords filter-list then the name of a configured AS-PATH list.
PAGE 375
Related Commands ● show debugging — view the enabled debugging operations. ● show ip bgp flap-statistics — view the BGP flap statistics. ● undebug all — disable all debugging operations. clear ip bgp peer-group Reset a peer-group’s BGP sessions. Syntax Parameters clear ip bgp [vrf vrf-name] peer-group peer-group-name [ipv4 [multicast | unicast] | ipv6 unicast] [soft {in | out}] vrf vrf-name Enter the keyword vrf and then the name of the VRF to reset the peer group corresponding to that VRF.
PAGE 376
Version Description 7.7.1.0 Introduced on the C-Series. deny bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. Syntax deny bandwidth To disable this setting, enter the no deny bandwidth command. Parameters Defaults bandwidth Enter the keyword bandwidth to specify extended-community attribute as the matching criteria for denying traffic. The range is from 0 to 102400.
PAGE 377
peer-group peer- Enter the keywords peer-group then the name of the peer group to debug. group-name in (OPTIONAL) Enter the keyword in to view only information on inbound BGP routes. out (OPTIONAL) Enter the keyword out to view only information on outbound BGP routes. A.B.C.D Enter the IP address of peer in the A.B.C.D format. X:X:X:X::X Enter the IPv6 IP address of peer in the X:X:X:X::X format. dampening Enter the keyword dampening to view BGP dampening.
PAGE 378
Related Commands ● ● ● ● ● debug ip bgp events — view information about BGP events. debug ip bgp keepalives — view information about BGP keepalives. debug ip bgp notifications — view information about BGP notifications. debug ip bgp updates — view information about BGP updates. show debugging — view enabled debugging operations. debug ip bgp dampening View information on routes being dampened.
PAGE 379
debug ip bgp events Display information on local BGP state changes and other BGP events. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] events [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] events [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP state changes corresponding to that VRF. A.B.C.
PAGE 380
debug ip bgp keepalives Display information about BGP keepalive messages. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] keepalives [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] keepalives [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP keepalive information corresponding to that VRF. A.B.C.
PAGE 381
debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] notifications [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] notifications [in | out] command.
PAGE 382
To disable, use the debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peergroup-name] soft-reconfiguration command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable soft-reconfiguration debugging on that VRF. A.B.C.D (OPTIONAL) Enter the IPv4 address of the neighbor in dotted decimal format. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group-name (OPTIONAL) Enter the name of the peer group to disable or enable all routers within the peer group.
PAGE 383
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view BGP updates information corresponding to that VRF. A.B.C.D (OPTIONAL) Enter an IPv4 address of the neighbor. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peer- (OPTIONAL) Enter the keyword peer-group followed by the name of the peer group-name group. in (OPTIONAL) Enter the keyword in to view only BGP updates received from neighbors.
PAGE 384
To return to the default setting, use the no default-metric command. Parameters Defaults number Enter a number as the metric to be assigned to routes from other protocols. The range is from 1 to 4294967295. 0 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 385
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 386
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Support from 2 to 64 paths on the S4810. Command syntax changed to maxpath (was maximum-paths). 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 387
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. By default, when you create a neighbor/peer group configuration in the Router BGP context, this enables IPv4/Unicast AFI/SAFI. When you use activate in the new context, the neighbor/peer group enables for AFI/SAFI.
PAGE 388
Defaults both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported. The range is from 2 to 64. none Command Modes CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 389
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 390
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peer-group-name} allowas-in command.
PAGE 391
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ip-address | peer-group-name} default-originate [route-map mapname] To remove a default route, use the no neighbor {ip-address | peer-group-name} default-originate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the default route of all routers in that peer group.
PAGE 392
You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. In order that settings corresponding to the neighbor default-originate command take effect, you must execute the clear ip bgp command immediately after you execute the neighbor default-originate command. neighbor description Assign a character string describing the neighbor or group of neighbors (peer group).
PAGE 393
To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to apply the distribute list filter to all routers in the peer group. prefix-list-name Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes).
PAGE 394
ttl Defaults (OPTIONAL) Enter the number of hops as the Time to Live (ttl) value. The range is from 1 to 255. The default is 255. Disabled. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 395
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.
PAGE 396
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation.
PAGE 397
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 398
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you configure the set next-hop command in ROUTE-MAP mode, the configuration takes precedence over the neighbor next-hop-self command. If you do not use the all keyword, the next hop of only eBGP-learned routes is updated by the route reflector. If you use the all keyword, the next hop of both eBGP- and iBGP-learned routes are updated by the route reflector.
PAGE 399
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. This command automatically restarts the neighbor session for the configuration to take effect. Configure the same password on both BGP peers or a connection does not occur. When you configure MD5 authentication between two BGP peers, each segment of the TCP connection between them is verified and the MD5 digest is checked on every segment sent on the TCP connection.
PAGE 400
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the dmzlink-bw parameter. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can assign up to 256 peers to one peer group.
PAGE 401
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 402
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced the limit keyword on the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 403
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. To accept 4-byte formats before entering a 4 byte AS Number, configure your system.
PAGE 404
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Applies to EBGP neighbors only. Configure your system to accept 4-byte formats before entering a 4 byte AS Number. If the AS-PATH contains both public and private AS number or contains AS numbers of an EBGP neighbor, the private AS numbers are not removed.
PAGE 405
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted. If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used in this command.
PAGE 406
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector, the internal BGP (IBGP) speakers in the network must be fully meshed. The first time you enter this command, the router configures as a route reflector and the specified BGP neighbors configure as clients in the route-reflector cluster.
PAGE 407
Usage Information Version Description Version 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To configure a COMMUNITY attribute, use the set community command in ROUTE-MAP mode. In order that settings corresponding to the neighbor send-community command take effect, you must execute the clear ip bgp command immediately after you execute the neighbor sendcommunity command.
PAGE 408
neighbor shutdown Disable a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} shutdown To enable a disabled neighbor or peer group, use the neighbor {ip-address | peer-groupname}no shutdown command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to disable or enable all routers within the peer group. Defaults Enabled (that is, BGP neighbors and peer groups are disabled.
PAGE 409
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to disable or enable all routers within the peer group. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 410
peer-group-name Enter the name of the peer group to set the timers for all routers within the peer group. Defaults keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds. holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds.
PAGE 411
ipv6-address Enter the IPv6 address of the peer router in X:X:X:X::X format. peer-group-name Enter the name of the peer group to set the timers for all routers within the peer group. timers extended idle holdtime Defaults Enter a number for the time interval, in seconds, for the peer to be idle state. The range is from 1 to 32767. The default is 15 seconds. The default idle holdtime is 15 seconds. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 412
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Loopback interfaces are up constantly and the BGP session may need one interface constantly up to stabilize the session. The neighbor update-source command is not necessary for directly connected internal BGP sessions.
PAGE 413
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. In the Dell EMC Networking OS best path selection process, the path with the highest weight value is preferred. NOTE: In the Dell EMC Networking OS best-path selection process, the path with the highest weight value is preferred. If you configure the set weight command in a route map applied to this neighbor, the weight set in that command overrides the weight set in the neighbor weight command.
PAGE 414
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 415
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 416
redistribute Redistribute routes into BGP. Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command. Parameters connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. These routes are treated as incomplete routes.
PAGE 417
Usage Information You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes. When you set the route-map with metric-type internal and applied outbound to an EBGP peer/ peer-group, the advertised routes corresponding to those peer/peer-groups have the IGP cost set as MED. If you do not configure the default-metric command, in addition to the redistribute command, or there is no route map to set the metric, the metric for redistributed static and connected is “0”.
PAGE 418
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
PAGE 419
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. At least one interface must be in Layer 3 mode for the router bgp command to be accepted. If all interfaces are configured under VRF, at least one interface should be in the default VRF for the router bgp command to be accepted. If no interfaces are enabled for Layer 3, an error message appears: % Error: No router id configured BGP does not allow 23456 (AS-TRANS) as a configured AS number.
PAGE 420
Use the no shutdown address-family-ipv4–unicast command to enable all the configured BGP neighbors corresponding to the unicast IPv4 address families. Command Modes ROUTER BGP CONFIGURATION Command History Usage Information Version Description 9.11.0.0 Introduced on the S-Series, Z-Series, MXL, and IOM. You can use this command to disable all the configured BGP neighbors corresponding to the unicast IPv4 address families. This command is global for all VRFs.
PAGE 421
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. A new policy command is introduced in order to attach the Link Bandwidth extended community only to the prefixes that are received from a neighbor that satisfy the desired conditions. This command is relevant for both inbound as well as outbound policy handling (for received prefixes).
PAGE 422
Available buffer size 40958758, 26 packet(s) captured using 680 bytes PDU[1] : len 101, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00650100 00000013 00000000 00000000 419ef06c 00000000 00000000 00000000 00000000 00000000 0181a1e4 0181a25c 41af92c0 00000000 00000000 00000000 00000000 00000001 0181a1e4 0181a25c 41af9400 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400
PAGE 423
router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC(conf-router_bgp)# show ip bgp View the current BGP IPv4 routing table for the system.
PAGE 424
neighbors [all {receivedroutes}] (OPTIONAL) Enter the keyword neighbors [all {received-routes}] to display all the received routes both accepted and rejected from all the IPv4 or IPv6 neighbors. next-hop (OPTIONAL) Enter the keyword next-hop to view all the next-hop information on the learnt routes. paths (OPTIONAL) Enter the keyword paths to view the BGP path attributes in the BGP database.
PAGE 425
Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the AS the route passed through to reach the destination network.
PAGE 426
ID 119.1.1.0/24 ID 120.1.1.0/24 11.1.1.2 11.1.1.2 0 0 100 100 0 ? 0 ? Following is the example for displaying all the received routes from all IPv6 neighbors: DellEMC# show ip bgp ipv6 unicast neighbors all received-routes BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 11.1.1.
PAGE 427
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view cluster information of BGP neighbors corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 multicast routes.
PAGE 428
BGP local router ID is 192.168.11.6 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *>I 55.0.0.0/24 *>I 66.0.0.0/24 *>I 77.0.0.0/24 Next Hop 172.16.0.2 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 0 400 500 600 i 0 0 500 i 0 0 i DellEMC# show ip bgp cluster-list 4.4.4.
PAGE 429
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 430
*> *> Network 55.0.0.0/24 66.0.0.0/24 Next Hop 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 200 i 0 200 i DellEMC# show ip bgp community no-advertise BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 66.
PAGE 431
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The show ip bgp community-list command without any parameters lists BGP routes matching the Community List and the output is the same as for the show ip bgp command output. The following describes the show ip bgp community-list pass command shown in the following example.
PAGE 432
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
PAGE 433
Example DellEMC# show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network d From 55.0.0.0/24 172.16.0.
PAGE 434
NdRRClsTblP 0x41a190a8 NdPktPA 0 : NdLocCBP 0x41a6f000 : NdTmpPAP 0x419efc80 : NdTmpASPAP 0x41a25000 : NdTmpCommP 0x41a25800 NdTmpRRClP 0x41a4b000 : NdTmpOptP 0x41a4b800 : NdTmpNHP : NdOrigPAP 0 NdOrgNHP 0 : NdModPathP 0x419efcc0 : NdModASPAP 0x41a4c000 : NdModCommP 0x41a4c800 NdModOptP 0x41a4d000 : NdModNHP : NdComSortBufP 0x41a19110 : NdComSortHdP 0x41a19d04 : NdUpdAFMsk 0 : AFRstSet 0x41a1a298 : NHopDfrdHdP 0x41a1a3e0 : NumNhDfrd 0 : CfgHdrAFMsk 1 AFChkNetTmrP 0x41ee705c : AFRtDamp 0 : AlwysCmpMed 0 : Lo
PAGE 435
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 436
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 437
Example Field Description Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. DellEMC# show run as-path a1 ! ip as-path access-list a1 permit 500 DellEMC# DellEMC# show ip bgp filter-list a1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 438
● ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. ● $ = (dollar sign) the end of the output string. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 439
show ip bgp inconsistent-as View routes with inconsistent originating autonomous system (AS) numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] inconsistent-as vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view routes corresponding to the VRF that contain inconsistent originating AS numbers.
PAGE 440
Status codes: s suppressed, d damped, h history, * valid, > best Path source: I - internal, c - confed-external, r - redistributed, n - network Origin codes: i - IGP, e - EGP, ? - incomplete Network Next * 3.0.0.0/8 * * *> *> 3.18.135.0/24 * * * *> 4.0.0.0/8 * * * * 6.0.0.0/20 * *> * * 9.2.0.0/16 * --More-- Hop Metric LocPrf Weight Path 63.114.8.33 0 18508 209 63.114.8.34 0 18508 209 63.114.8.60 0 18508 209 63.114.8.33 0 18508 701 63.114.8.60 0 18508 209 63.114.8.34 0 18508 209 63.114.8.33 0 18508 701 63.
PAGE 441
ip-address (OPTIONAL) Enter the IP address of the neighbor to view only BGP information exchanged with that neighbor. advertisedroutes (OPTIONAL) Enter the keywords advertised-routes to view only the routes the neighbor sent. dampened-routes (OPTIONAL) Enter the keywords dampened-routes to view information on dampened routes from the BGP neighbor. detail (OPTIONAL) Enter the keyword detail to view neighbor-specific internal information for the IPv4 Unicast address family.
PAGE 442
Usage Information Version Description 7.2.1.0 Added the received and denied route options. 6.3.10 The output is changed to display the total number of advertised prefixes. After a peer reset, the contents of the notification log messages is displayed in hex values for debugging. The neighbor information that this command displays does not include counts corresponding to ignored prefixes and updates.
PAGE 443
Example The Lines Beginning with: Description Last reset Displays the amount of time since the peering session was last reset. Also states if the peer resets the peering session. If the peering session was never reset, the word never is displayed. Local host: Displays the peering address of the local router and the TCP port number. Foreign host: Displays the peering address of the neighbor and the TCP port number. DellEMC# show ip bgp neighbors 172.16.0.2 BGP neighbor is 172.16.0.
PAGE 444
show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. Syntax show ip bgp [vrf vrf-name] next-hop Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 444 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 445
show ip bgp paths View all the BGP path attributes in the BGP database. Syntax Parameters show ip bgp[vrf vrf-name] paths [regexp regular-expression] vrf vrf-name (OPTIONAL) Enter the keyword vrf to view all path attributes in the BGP database corresponding to that VRF. NOTE: DescriptionYou can use this attribute to view information on all path attributes in the BGP database that correspond to either a default or a nondefault VRF.
PAGE 446
Usage Information Example Version Description 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp path command shown in the following example. Field Description Total Displays the total number of BGP path attributes. Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using this path attribute.
PAGE 447
Usage Information Example Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp paths community command shown in the following example.
PAGE 448
summary (OPTIONAL) Enter the keyword summary to view status information of the peers in that peer group. The output is the same as that found in the show ip bgp summary command. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 449
For address family: IPv4 Unicast BGP neighbor is port0, peer-group external Update packing has 4_OCTET_AS support enabled Number of peers in this group 1 Maximum limit on the accepted connections 256 Peer-group members (* - outbound optimized): 172.16.0.2 DellEMC# Related Commands ● neighbor peer-group (assigning peers) — assign a peer to a peer-group. ● neighbor peer-group (creating group) — create a peer group.
PAGE 450
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 451
ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 452
Field Description BGP path attribute entries Displays the number of BGP path attributes and the amount of memory used to process them. BGP AS-PATH entries Displays the number of BGP AS_PATH attributes processed and the amount of memory used to process them. BGP community entries Displays the number of BGP COMMUNITY attributes processed and the amount of memory used to process them. The show ip bgp community command provides more details on the COMMUNITY attributes.
PAGE 453
show running-config bgp To display the current BGP configuration, use this feature. Syntax show running-config bgp Defaults none Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 454
holdtime Defaults Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 455
Usage Information The peer remains in idle state based on the configured idle-holdtime. The less the idle-holdtime, lesser the peer in idle state. For the new idle-holdtime to take effect, you need to shutdown all the peers manually using neighbor shutdown command and enable the peers again. MBGP Commands Multiprotocol BGP (MBGP) is an enhanced BGP that enables multicast routing policy throughout the internet and connecting multicast topologies between BGP and autonomous systems (ASs).
PAGE 456
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced IPv6 MGBP support for the E-Series. distance bgp Configure three administrative distances for routes.
PAGE 457
The higher the administrative distance assigned to a route means that your confidence in that route is low. Routes assigned an administrative distance of 255 are not installed in the routing table. Routes from confederations are treated as internal BGP routes. Related Commands ● router bgp — enter ROUTER mode on the switch. show ip bgp dampened-paths View BGP routes that are dampened (non-active).
PAGE 458
Usage Information To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized. The history paths that the show ip bgp command displays contain only the prefix and the next-hop information.
PAGE 459
Defaults IPADDR:NN Enter the IP address specific extended community in the format IPADDR:NN (4byte IPv4 Unicast Address:2-byte community value). additive (OPTIONAL) Enter the keyword additive to add to the existing extended community. non-trans (OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific.
PAGE 460
Defaults none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 461
Usage Information Example The following describes the show ip bgp paths extcommunity command shown in the following example. Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these extended communities. Community Displays the extended community attributes in this BGP path.
PAGE 462
IPv6 BGP Commands IPv6 border gateway protocol (IPv6 BGP) is supported on the platform. BGP is an external gateway protocol that transmits interdomain routing information within and between Autonomous Systems (AS). Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically send messages to update those routing tables.
PAGE 463
debug ip bgp ipv6 unicast soft-reconfiguration Enable soft-reconfiguration debugging for IPv6 unicast routes. Syntax debug ip bgp [ipv4-address | ipv6-address | peer-group-name] ipv6 unicast soft-reconfiguration To disable debugging, use the no debug ip bgp [ipv4-address | ipv6-address | peergroup-name] ipv6 unicast soft-reconfiguration command. Parameters ipv4-address | ipv6-address Enter the IP address of the neighbor on which you want to enable softreconfiguration debugging.
PAGE 464
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. neighbor soft-reconfiguration inbound Enable a BGP soft-reconfiguration and start storing updates for inbound IPv6 unicast routes.
PAGE 465
prefix-list name Enter the name of the prefix list. NOTE: There is a 140-character limit for prefix list names. summary Display a summary of RPF routes. Command Modes EXEC Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.10.
PAGE 466
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 467
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● IPV6Acl : 0 IPV4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 nlbclusteracl: 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 ipv4udfmirracl: 0 vrfv4Acl :0 Openflow : 0 fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 8.
PAGE 468
fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The range is from 0 to 6. Iscsioptacl Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2. number ipv4udfmirracl Enter the keyword ipv4udfmirracl and then the number of FP blocks for IPv4 UDF mirror ACL. The range is from 0 to 8. ipv4mirracl Enter the ipv4mirracl keyword and then the number of FP blocks for IPv4 mirror ACL. The range is from 0 to 8.
PAGE 469
The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only number of blocks can be configured by the user . If allocation values are not entered for the CAM regions, the value is 0. If you enable BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the command reload conditional nvram-cfg-change. cam-acl-egress Allocate CAM for egress ACLs.
PAGE 470
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 471
Command History Usage Information Example Version Description 9.14.1.0 Introduced on the S4810 and S4820T. 9.13.0.0 Introduced on the MXL, FN IOM, S5000, S4048-ON, S6000, S6000-ON, S3048ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. The no cam-threshold command will set the CAM threshold to 90 percent and silence period to 0. The CAM threshold and silence period configuration is applicable only for Ingress L2, IPv4, IPv6 and Egress L2, IPv4, and IPv6 ACL CAM groups.
PAGE 472
Example DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p
PAGE 473
IPV6(IPV4QOS) Triple Wide Regions: VmanQos, Openflow, ipv4udfmirracl L2Acl : 2 Ipv4Acl : 4 Ipv6Acl* : 2 Ipv4Qos* : 0 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl: 0 ipv4mirracl : 0 * - shared regions show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow) Syntax Parameters Defaults show
PAGE 474
Table 3.
PAGE 475
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 476
Unified Forwarding Table Modes Unified Forwarding Table (UFT) consolidates the resources of several search tables (Layer 2, Layer 3 Hosts, and Layer 3 Route [Longest Prefix Match — LPM]) into a single flexible resource. The system supports several UFT modes to extract the forwarding tables, as required. By default, Dell EMC Networking OS initializes the table sizes to UFT mode 2 profile, as it provides a reasonable shared memory for all the tables.
PAGE 477
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.
PAGE 478
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 479
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax Parameters Defaults service-policy rate-limit-cpu-queues policy-name policy-name Enter the service-policy name, using a string up to 32 characters. Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History Usage Information This guide is platform-specific.
PAGE 480
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 481
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload.
PAGE 482
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 483
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 484
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 485
LLDP GVRP STP ISIS DellEMC# any 01:80:c2:00:00:21 01:80:c2:00:00:00 01:80:c2:00:00:14/15 09:00:2b:00:00:04/05 0x88cc any any any any Q8 Q8 Q7 Q9 Q9 CP CP CP CP CP _ _ _ _ Control Plane Policing (CoPP) 485
PAGE 486
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 487
Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 488
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 489
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release.
PAGE 490
● The maximum number of lossless queues globally supported on the switch is two. The following lists the dot1p priority-queue assignments. dot1p Value in Description heading the Incoming Frame 0 1 1 0 2 2 3 3 4 4 5 5 6 6 7 7 ● Before configuring the port queues to function as no-drop queues, you must first apply the dcb-map map with pfc mode off. To apply the dcb-map with pfc mode off, use the following commands: dcb-map pfcoff and no pfc mode on.
PAGE 491
show interface pfc Displays the PFC configuration applied to ingress traffic on an interface, including priorities and link delay. Syntax Parameters show interface port-type slot/port[/subport] pfc {summary | statistics | detail | buffer-threshold} port-type slot/ port[ /subport ] pfc Enter the port-type slot and port PFC information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 492
Field Description from peers; received PFC configuration take effect. The admin operational status for a DCBX exchange of PFC configuration is enabled or disabled. 492 Remote is enabled, Priority list Remote Willing Status is enabled Operational status (enabled or disabled) of peer device for DCBX exchange of PFC configuration with a list of the configured PFC priorities. Willing status of peer device for DCBX exchange (Willing bit received in PFC TLV): enabled or disable.
PAGE 493
Example (Summary) Field Description PFC TLV Statistics: Error pkts Number of PFC error packets received. PFC TLV Statistics: Pause Tx pkts Number of PFC pause frames transmitted. PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
PAGE 494
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 495
Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 496
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default, equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure bandwidth amounts in associated dot1p queues, use the bandwidth-percentage command.
PAGE 497
dcb-enable Enable data center bridging. Syntax dcb enable[pfc-queues 1–4] To disable DCB, use the no dcb enable command. Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 498
Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. priority-list Configure the 802.1p priorities for the traffic on which you want to apply an ETS output policy. Syntax priority-list value To remove the priority list, use the no priority-list command. Parameters Defaults value Enter the priority list value. Separate priority values with a comma; specify a priority range with a dash; for example, priority-list 3,5-7.
PAGE 499
Usage Information If an error occurs in an ETS output-policy configuration, the configuration is ignored and the scheduler and bandwidth allocation settings are reset to the ETS default values (all priorities are in the same ETS priority group and bandwidth is allocated equally to each priority). If an error occurs when a port receives a peer’s ETS configuration, the port’s configuration is reset to the previously configured ETS output policy.
PAGE 500
show interface ets Displays the ETS configuration applied to egress traffic on an interface, including priority groups with priorities and bandwidth allocation. Syntax show interface port-type slot/port[/subport] ets {summary | detail} Parameters port-type slot/ port[/subport] ets Enter the port-type slot and port ETS information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 501
0 1 2 3 4 5 6 7 0,1,2 3 4,5,6,7 100% 0 % 0 % - ETS SP SP - Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf T
PAGE 502
3 4 5 6 7 4,5,6,7 0 % - SP - Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts DellEMC# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----
PAGE 503
Class Pkts Example (Detail) DellEMC(conf)# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled
PAGE 504
show qos priority-groups Displays the ETS priority groups configured on the switch, including the 802.1p priority classes and ID of each group. Syntax show qos priority-groups Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 505
1 2 3 4 5 6 7 8 - - Stack unit 2 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 - DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements.
PAGE 506
advertise dcbx-appln-tlv On a DCBX port with a manual role, configure the application priority TLVs advertised on the interface to DCBX peers. Syntax advertise dcbx-appln-tlv {fcoe | iscsi} To remove the application priority TLVs, use the no advertise dcbx-appln-tlv {fcoe | iscsi} command. Parameters Defaults {fcoe | iscsi} Enter the application priority TLVs, where: ● fcoe: enables the advertisement of FCoE in application priority TLVs.
PAGE 507
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. You can configure the transmission of more than one TLV type at a time; for example: advertise dcbx-tlv ets-conf ets-reco. You can enable ETS recommend TLVs (ets-reco) only if you enable ETS configuration TLVs (etsconf).
PAGE 508
Usage Information Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. If you use the auto-upstream option and the port does not come up on a switch from a different vendor, manually configure the version a CEE on the peer device.
PAGE 509
debug dcbx Enable DCBX debugging. Syntax debug dcbx {all | auto-detect-timer | config-exchng | fail | mgmt | resource | sem | tlv} To disable DCBX debugging, use the no debug dcbx command. Parameters Defaults {all | autodetect-timer | config-exchng | fail | mgmt | resource | sem | tlv} Enter the type of debugging, where: ● all: enables all DCBX debugging operations. ● auto-detect-timer: enables traces for DCBX auto-detect timers. ● config-exchng: enables traces for DCBX configuration exchanges.
PAGE 510
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. This command is available at the global level only.
PAGE 511
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 512
Field Description Local DCBX TLVs Transmission status (enabled or disabled) of advertised DCB TLVs (see TLV code Transmitted at the top of the show command output). Local DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs. Local DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs. Local DCBX Sequence number transmitted in Control TLVs. Status: Sequence Number Local DCBX Acknowledgement number transmitted in Control TLVs.
PAGE 513
F-Application priority for FCOE enabled f-Application Priority for FCOE disabled I-Application priority for iSCSI enabled i-Application Priority for iSCSI disabled ----------------------------------------------------------Interface TenGigabitEthernet 1/9 Remote Mac Address 00:00:00:00:00:11 Port Role is Auto-Upstream DCBX Operational Status is Enabled Is Configuration Source? TRUE Local DCBX Compatibility mode is CEE Local DCBX Configured mode is CEE Peer Operating version is CEE Local DCBX TLVs Transmitted
PAGE 514
Usage Information A DCB map is a template used to configure DCB parameters and apply them on converged Ethernet interfaces. DCB parameters include priority-based flow control (PFC) and enhanced traffic selection (ETS). To display the PFC and ETS settings in DCB maps, enter the show qos dcb-map name command. Use the dcb-map command to create a DCB map to specify PFC and ETS settings and apply it on Ethernet ports.
PAGE 515
For PFC enabled priorities, it is recommended to map single priority per Priority group. pfc mode on Enable the PFC configuration on the port so that the priorities are included in DCBX negotiation with peer PFC devices. Syntax pfc mode on To disable the PFC configuration, use the no pfc mode on command. Defaults PFC mode is on. Command Modes DCB MAP Command History Usage Information This guide is platform-specific.
PAGE 516
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.
PAGE 517
Usage Information Version Description 9.3(0.0) Introduced on the S4810 and S6000 platforms. The dcb-map stack-unit all stack-ports all command overwrites any previous DCB maps applied to stack ports. show qos dcb-map Display the DCB parameters configured in a specified DCB map. Syntax Parameters show qos dcb-map map-name map-name Displays the PFC and ETS parameters configured in the specified map.
PAGE 518
PG:1 TSA:ETS Priorities:3 BW:50 PFC:ON dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. Syntax dcb pfc-shared—buffer—size buffer-size Parameters Default buffer-size Enter a number in the range of 0 to 7787. The default is 832KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific.
PAGE 519
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.0) Introduced on the S5000. 9.3(0.0) Introduced on the S4810, S4820T, and S6000.
PAGE 520
threshold-value Buffer offset limit at which the port resumes the peer in KB. Enter a number in the range of 1 to 7787. The default is 10 KB. sharedBuffer shared threshold weight threshold-weight size Weightage of the priorities on the shared buffer size in the system. Enter a number in the range of 0 to 9. The default shared threshold weight is 10. Command Modes DCB-BUFFER-THRESHOLD mode Command History Usage Information This guide is platform-specific.
PAGE 521
queue 0 to queue Specify the queue number to which the QoS policy buffer parameters apply 7 pause Pause frames to be sent at the specified buffer limit levels and pause packet settings no-drop The packets for this queue must not be dropped value Enter a number in the range of 0 to 7 to denote the priority to be allocated to the dynamic buffer control mechanism buffer-size Ingress buffer size size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 45 KB.
PAGE 522
dcb-policy buffer-threshold (Interface Configuration) Assign the DCB policy to the DCB buffer threshold profile on interfaces. This setting takes precedence over the global buffer-threshold setting. Syntax dcb-policy buffer-threshold profile-name Parameters Default buffer-threshold Configure the profile name for the DCB buffer threshold profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
PAGE 523
Version Description 9.9(0.0) Introduced on the S6000 and the S6000–ON. 9.8(0.0) Introduced on the S4048-ON. 9.6(0.0) Introduced on the S5000. 9.3(0.0) Introduced on the S4810 and S4820T platforms. Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process.
PAGE 524
dcb pfc-total-buffer-size Configure the total buffer size for PFC in kilobytes. Syntax dcb pfc-total—buffer—size buffer-size Parameters Default buffer-size Enter a number in the range of 0 to 7787. The default is 6592KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 525
show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration. Syntax show running—config dcb-buffer-threshold Command Modes EXEC EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 526
7 - No Denotes dynamic buffering is enabled in respective queues - On interface in which PFC is not enabled: DellEMC#show interface tengigabitethernet 1/20 pfc buffer-threshold The following table describes the output fields displayed for the show interface pfc bufferthreshold command: Field Description queue Number of the queue lossless Whether the queue is a lossy or lossless queue for which buffer threshold is configured buffer-size Ingress buffer size pause-threshold- Buffer limit at which t
PAGE 527
Usage Information Example You can configure all the data queues. You can configure queues 0-7. The following table describes the mapping between the threshold weight of the shared buffer on the queue. It also shows the percentage of the available shared buffer used by the queues for each of the corresponding threshold weights of the shared buffer: sharedthresholdweight on the queue % of available shared buffer that can be consumed by the queue 0 No dynamic sharing; shared buffer = 0. 1 0.77% 2 1.
PAGE 528
space to be allocated for each priority and the pause or resume thresholds for the buffer. This method of configuration enables you to effectively manage and administer the behavior of lossless queues. Example DellEMC(conf)# dcb pfc-queues 4 dcb {ets | pfc} enable Enable priority flow control or enhanced transmission selection on interface. Syntax dcb {ets | pfc} enable ● To disable ETS on interface, use “no dcb ets enable” command. ● To disable PFC on interface, use “no dcb pfc enable” command.
PAGE 529
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 530
is not reachable, the application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
PAGE 531
no-reboot Defaults Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit stack-unit-number command. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 532
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process.
PAGE 533
Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 534
Related Commands Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. ● show hardware stack-unit — display the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
PAGE 535
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 536
show hardware mac Display MAC ACL entries for the specified stack-unit, port-pipe and pipeline ID. Syntax show hardware mac {eg-acl | in-acl} stack-unit id port-set 0–0 Parameters Defaults eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack- unit id Enter the keyword stack-unit to select the stack unit ID.
PAGE 537
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 538
Defaults drops [unit unitnumber ] Enter the keyword drops to display internal drops on the selected stack member. Enter the optional keyword unit unit-number to display the internal drop counters of the specified port pipe. fpga register Enter the keyword to display the register value of the fpga register.
PAGE 539
0 Multicasts, 3 Broadcasts, 322 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec Output 00.
PAGE 540
0x0060a04c ASFPORTSPEED.ge10 = 0x00000000 0x0060b04c ASFPORTSPEED.ge11 = 0x00000000 0x0060c04c ASFPORTSPEED.ge12 = 0x00000000 0x0060d04c ASFPORTSPEED.ge13 = 0x00000000 0x0060e04c ASFPORTSPEED.ge14 = 0x00000000 0x0060f04c ASFPORTSPEED.ge15 = 0x00000000 0x0061004c ASFPORTSPEED.ge16 = 0x00000000 0x0061104c ASFPORTSPEED.ge17 = 0x00000000 0x0061204c ASFPORTSPEED.ge18 = 0x00000000 0x0061304c ASFPORTSPEED.ge19 = 0x00000000 0x0061404c ASFPORTSPEED.ge20 = 0x00000000 0x0061504c ASFPORTSPEED.
PAGE 541
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Fra
PAGE 542
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter 8 Debug Counter 9 Debug Counter 10 Debug Counter 11 3 4 5 6 7 --------------------unit: 0 port: 61 (interface Fo 1/60) Description RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX
PAGE 543
RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - Debug Counter 6 Debug Counter 7 Debug Counter 8 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Fra
PAGE 544
****************************************************** Link Status of all the ports in the Device - 1 The linkStatus of Front End Port 0 is FALSE The linkStatus of Front End Port 1 is FALSE The linkStatus of Front End Port 2 is FALSE The linkStatus of Front End Port 3 is FALSE The linkStatus of Front End Port 4 is FALSE The linkStatus of Front End Port 5 is FALSE The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus
PAGE 545
Related Commands ● clear hardware system-flow — clear the statistics from selected hardware components. ● show interfaces stack-unit — display information on all interfaces on a specific S-Series stack member. ● show processes cpu (S-Series) — display the CPU usage information based on the processes running in an S-Series. ● show system — display the current status of all the stack members or a specific member.
PAGE 546
2036 VRRP STUB 2035 L2_DST_HIT+BC MAC+VLAN 4095 2034 L2_DST_HIT+BC MAC 2033 Catch all 384 OSPF[224.0.0.5] Packets 383 OSPF[224.0.0.
PAGE 547
show hardware vlan-counters Display the hardware VLAN statistics. Syntax Parameters Defaults show hardware vlan-counters vlan-id vlan-id Enter the interface VLAN number. The range is from 1 to 4094. None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 548
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 549
show hardware drops Displays internal drops on the specified interface or for a range of interface. Syntax Parameters show hardware drops interface interface drops Enter the keyword drops to display internal drops. interface Enter any of the following keywords and the interface or interface range information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 550
Example displaying internal drops DellEMC# show hardware drops interface tengigabitethernet 2/1 Drops in Interface Te 2/1: --- Ingress Drops --Ingress Drops IBP CBP Full Drops PortSTPnotFwd Drops IPv4 L3 Discards Policy Discards Packets dropped by FP (L2+L3) Drops Port bitmap zero Drops Rx VLAN Drops --- Ingress MAC counters--Ingress FCSDrops Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DR
PAGE 551
buffer-statssnapshot unit number buffer-info Display the historical snapshot of buffer statistical values unit Enter the keyword unit along with a port-pipe number. The range is from 0 to 0.
PAGE 552
5 6 7 4 3 0-2,5 0 0 0 0 0 0 show hardware buffer interface Display buffer statistics for a specific interface. Syntax show hardware buffer interface interface{priority-group { id | all } | queue { id| all} ] buffer-info Parameters interface interface Enter any of the following keywords and slot/port[/subport] or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 553
Example displaying queue range show hardware buffer-stats-snapshot Displays buffer statistics tracking resource information for a specific interface.
PAGE 554
packets for the specific interface Example displaying egress queue-level snapshot for unicast packets for the specific interface UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 queue ucast 10 Unit 0 unit: 0 port: 1 (interface Fo 1/49) -----------------------------
PAGE 555
MCAST MCAST MCAST MCAST MCAST MCAST Example displaying ingress prioritygroup level snapshot for the specific interface 3 4 5 6 7 8 0 0 0 0 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 priority-group 7 Unit 1 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------7 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 priority-group all Unit 1 unit: 0
PAGE 556
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 557
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP.
PAGE 558
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 559
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific.
PAGE 560
Parameters Defaults address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 561
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. excluded-address Prevent the server from leasing an address or range of addresses in the pool.
PAGE 562
hardware-address For manual configurations, specify the client hardware address. Syntax hardware-address address Parameters Defaults address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 563
Usage Information When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.3 or later, the system converts the DHCP CONFIGURATION host command in the running configuration to the hostaddress command. If you downgrade the Dell EMC Networking OS from version 9.14.1.3 or later to an earlier version, any existing host-address command is deleted from the running configuration. If you want to create manual DHCP bindings, use the host command. ip dhcp server Enable DHCP server globally.
PAGE 564
Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 565
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell EMC Networking recommends specifying clients as hybrid.
PAGE 566
network Specify the range of addresses in an address pool. Syntax network network /prefix-length Parameters Defaults network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 567
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 568
show ip dhcp configuration Display the DHCP configuration. Syntax show ip dhcp configuration [global | pool name] Parameters Defaults pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 569
show ip dhcp conflict Display the address conflict log. Syntax Parameters Defaults show ip dhcp conflict address address Display a particular conflict log entry. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 570
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms.
PAGE 571
Related Commands ● arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table. arp inspection-limit Configure dynamic ARP inspection rate-limit to verify the rate of ARP packet received in a port on a specific interval. Syntax arp inspection-limit {rate pps [interval seconds]} Defaults None Command Modes INTERFACE CONFIGURATION Parameters Command History rate pps Enter the keyword rate then the packet per second (pps) value.
PAGE 572
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. ● arp inspection — enable dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. Syntax clear ip dhcp snooping {binding | source-address-validation discardcounters [interface interface]} Parameters binding Clears the binding table.
PAGE 573
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 574
ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] Parameters Defaults remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82. remote-id port Enter the keywords remote-id port to configure the port as the remote id in option–82.
PAGE 575
ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 576
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ipv6 dhcp snooping vlan Enable ipv6 DHCP Snooping on VLAN or range of VLANs.
PAGE 577
Defaults interface type Enter the keyword interface then the type of interface to which the host is connected: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. lease time Enter the keyword lease then the amount of time the IP address are leased. The range is from 1 to 4294967295.
PAGE 578
To delete the DHCP snooping binding entry from DHCP snooping database, use the [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease valuecommand. Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IPv6 address. vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 579
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 580
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 581
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 582
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp source-address-validation Enable the IP Source Guard.
PAGE 583
Usage Information Version Description 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system. ip dhcp relay information-option Enable Option 82.
PAGE 584
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series. DellEMC(conf)# ip dhcp relay information-option vpn ip dhcp relay source-interface Configure IPv4 DHCP relay source interface.
PAGE 585
Related Commands Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface. ipv6 dhcp relay source-interface Configure DHCP relay source IPv6 interface.
PAGE 586
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 587
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
PAGE 588
ipv6-address Default Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Enhanced to support non-default VRF configuration for DHCPv6 helper address. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 589
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 590
Total cam count 5 permit host 0.0.0.0 permit vlan 10 host permit vlan 10 host permit vlan 10 host host 00:00:00:00:00:00 count (0 packets) 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) NOTE: The output for port-channel interfaces does not display the physical interface.
PAGE 591
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. DellEMC# show ipv6 dhcp snooping IPv6 DHCP Snooping IPv6 DHCP Snooping Mac Verification : Enabled. : Disabled.
PAGE 592
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to associate the system with one or more DNS servers.
PAGE 593
Usage Information Example Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. DellEMC(conf)# ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 594
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrfname] name ip-address command.
PAGE 595
Defaults None Command Modes EXEC Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 596
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • • • • • ecmp-group hash-algorithm hash-algorithm ecmp hash-algorithm seed ip ecmp-group ip ecmp weighted link-bundle-monitor enable link-bundle-distribution trigger-threshold show config show link-bundle distribution ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
PAGE 597
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID.
PAGE 598
● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR hg { crc16 | crc16cc | Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices: crc32MSB | ● crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) crc32LSB | xor1 | ● crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial xor2 | xor4 | xor8 ● crc32MSB: Use CRC32_UPPER — MSB 16 bits of computed CRC32 |
PAGE 599
Usage Information Version Description 9.9(0.0) Added flow-based-hashing support for hashing on ECMP for S4820T, S6000, S4048 and Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.
PAGE 600
hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters Defaults crc-upper Uses the upper 32 bits of the key for the hash computation. The default is crclower. dest-ip Uses the destination IP for ECMP hashing. The default is enabled.
PAGE 601
stack–unit slot/ port port-set number Defaults Enter the keyword stack-unit then the slot/port[subport] number. Enter the keyword port-set then the port-pipe number. The value is 0. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 602
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 603
Example DellEMC(conf)# ip ecmp ? weighted Enables Weighted ECMP DellEMC(conf)# ip ecmp weighted DellEMC(conf)#do show running-config | grep ecmp ip ecmp weighted DellEMC(conf)# DellEMC(conf)# no ip ecmp ? weighted Disables Weighted ECMP DellEMC(conf)# no ip ecmp weighted DellEMC(conf)# do show running-config | grep ecmp link-bundle-monitor enable Provides a mechanism to enable monitoring of traffic distribution on an ECMP link bundle.
PAGE 604
Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 605
show link-bundle distribution Display the link-bundle distribution for the interfaces in the bundle, type of bundle (LAG or ECMP), and the most recently calculated interface utilization (either bytes per second rate or maximum rate) for each interface. Syntax show link-bundle-distribution Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 606
16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: Topics: • • • • fips mode enable show fips status show ip ssh ssh fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 607
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 608
Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256cbc,aes128-ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-sha1-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled.
PAGE 609
● aes128–ctr: Force ssh to use the aes256–cbc encryption cipher. ● aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. ● 3des-cbc: Force ssh to use 3des-cbc encryption cipher. -l username (OPTIONAL) Enter the keyword —l then the user name used in this SSH session. The default is the user name of the user associated with the terminal. -m HMAC algorithm Enter one of the following HMAC algorithms to use. (For v2 clients only.
PAGE 610
Example If FIPS mode is not enabled: DellEMC# ssh 10.10.10.10 ? -c Encryption cipher to use (for v2 clients only) -l User name option -m HMAC algorithm to use (for v2 clients only) -p SSH server port option (default 22) -v SSH protocol version DellEMC# ssh 10.10.10.
PAGE 611
17 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE end-device and an FCF.
PAGE 612
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface.
PAGE 613
info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 614
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 9.2(0.2) Introduced on the S4810 and S4820T. Added the receive parameters packettype and interfaces and their options.
PAGE 615
fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN. Syntax fip-snooping enable To disable the FIP snooping feature on all or a specified VLAN, use the no fip-snooping enable command. Defaults FIP snooping is disabled on all VLANs. Command Modes ● CONFIGURATION ● VLAN INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 616
Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. fip-snooping max-sessions-per-enodemac Configure the maximum session limit per ENode MAC address. Syntax fip-snooping max—sessions—per—enode—mac max-sessions-value To return the configured maximum sessions to the default value, use the no fip-snooping max— sessions—per—enode—mac command.
PAGE 617
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links. It is not recommended to use this command because multi-hop FSB is not supported.
PAGE 618
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 619
Example Field Description FC-ID Fibre Channel session ID the FCF assigns. DellEMC# show fip-snooping enode Enode MAC Enode Interface FCF MAC VLAN FC-ID --------- --------------- ------- ---- ----d4:ae:52:1b:e3:cd Te 1/11 54:7f:ee:37:34:40 100 62:00:11 show fip-snooping fcf Display information on the FCFs in FIP-snooped sessions, including the FCF interface and MAC address, FCF interface, VLAN ID, FC-MAP value, FKA advertisement period, and number of ENodes connected.
PAGE 620
------- ------------- ---- ------ -------------- ------------54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax show fip-snooping statistics [interface vlan vlan-id | interface interfacetype | interface port-channel port-channel-number] Parameters vlan-id Enter the VLAN ID of the FIP packet statistics displays.
PAGE 621
Field Description Number of ENode Number of FIP-snoop ENode keep-alive frames received on the interface. Keep Alives Number of VN Port Keep Alives Number of FIP-snoop VN port (Virtual N-port) keep-alive frames received on the interface Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snoop unicast discovery advertisements received on the interface.
PAGE 622
Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int tengigabitethernet 1/11 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of FLOGI :1 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :4416 Number of VN Port Keep Alive :3136 Number of Multicast Discovery Advertisement :0 Number of Unicast Discover
PAGE 623
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 624
show fips status Display the FIPs status on the platform. Syntax show fips status Defaults none Command Modes EXEC Command History 624 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 625
18 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
PAGE 626
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 627
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 628
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol.
PAGE 629
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 630
Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration. Ownership is relinquished for a port only when the interface does not play a part in any control VLAN, that is, the interface does not belong to any ring. Related Commands ● show frrp — display the Resilient Ring Protocol configuration information. member-vlan Specify the member VLAN identification numbers.
PAGE 631
To reset the mode, use the no mode {master | transit} command. Parameters Defaults master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 632
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced This command places you into the resilient ring protocol.
PAGE 633
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
PAGE 634
● The number of state change counters Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command is executed.
PAGE 635
To remove the timer, use the no timer {hello-interval [milliseconds]}| {deadinterval milliseconds} command. Parameters hello-interval milliseconds dead-interval milliseconds Defaults Enter the keyword hello-interval then the time, in milliseconds, to set the hello interval of the control packets. The milliseconds must be entered in increments of 50 millisecond; for example, 50, 100, 150, and so on. If an invalid value is entered, an error message is generated. The range is from 50 to 2000 ms.
PAGE 636
19 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 637
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax Parameters clear gvrp statistics interface interface interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 638
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters Defaults config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 639
To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 640
NOTE: Designate the milliseconds in multiples of 100. Defaults As above. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 641
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 642
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 643
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series ● disable — globally disable GVRP. show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific.
PAGE 644
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 645
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 646
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. summary Defaults Enter the keyword summary to display just a summary of the GVRP statistics. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 647
Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 DellEMC# Related Commands ● show gvrp — display the GVRP configuration.
PAGE 648
20 High Availability (HA) High availability (HA) in the Dell EMC Networking OS is the configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol. You must specifically enable some protocols for HA.
PAGE 649
Usage Information Enabling this command keeps the failed RPM in the failed state. If there are two RPMs in the system, enabling this command prevents the failed RPM from becoming a working Standby RPM. If there is only one RPM in the system, the failed RPM does not recover and affects the system. redundancy force-failover Force the secondary stack unit to become the primary stack unit.
PAGE 650
Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. redundancy protocol Enable hitless protocols.
PAGE 651
show redundancy Display the current redundancy configuration. Syntax show redundancy Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 652
Field Description ● the time and date of the last RPM failover ● the reason for the last RPM failover Last Data Sync Record Displays the data sync information and the timestamp for the data sync: ● Start-up Config is the contents of the startup-config file. ● Line Card Config is the line card types configured and interfaces on those line cards. ● Runtime Event Log is the contents of the Event log. ● Running Config is the current running-config.
PAGE 653
21 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 654
Table 4. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 654 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 655
22 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
PAGE 656
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 657
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 658
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. The access list accepted is an extended ACL.
PAGE 659
Version Description 7.7.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion.
PAGE 660
Version Description E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters Defaults seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 661
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 662
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 663
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax Parameters Defaults ip igmp version {2 | 3} 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. 2 (IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 664
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 665
Example Example (VLT) Field Description Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. DellEMC# show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.0.2 Vlan 100 00:00:05 00:02:04 225.0.0.3 Vlan 100 00:00:05 00:02:04 225.0.0.
PAGE 666
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 667
Internet address is 35.0.0.1/24 IGMP is enabled on interface IGMP query interval is 60 seconds IGMP querier timeout is 125 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is enabled for all groups IGMP activity: 0 joins IGMP querying router is 35.0.0.1 (this system) IGMP version is 2 Example (VRF) DellEMC# show ip igmp vrf BLUE interface TenGigabitEthernet 1/20 Inbound IGMP access group is not set Internet address is 50.10.4.
PAGE 668
Example Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 669
Important Points to Remember for IGMP Querier ● The IGMP snooping Querier supports version 2. ● You must configure an IP address to the VLAN interface for IGMP snooping Querier to begin. The IGMP snooping Querier disables itself when a VLAN IP address is cleared, and then it restarts itself when an IP address is reassigned to the VLAN interface. ● When enabled, IGMP snooping Querier does not start if there is a statically configured multicast router interface in the VLAN.
PAGE 670
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax debug ip igmp snooping [group address | interface] ● To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. ● To disable all debugging, use the undebug all command. Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 671
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 672
Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
PAGE 673
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to GroupLeave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters Defaults milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
PAGE 674
To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 675
To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 676
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 677
show ip igmp snooping mrouter Display multicast router interfaces. Syntax Parameters show ip igmp snooping mrouter [vlan number] vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 678
23 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • • • Basic Interface Commands Egress Interface Selection (EIS) Commands Port Channel Commands Time Domain Reflectometer (TDR) Commands UDP Broadcast Commands ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 679
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. vrrp [ipv6 {vr-id} (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To | vr-id] clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
PAGE 680
Related Commands ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 681
dampening Configure dampening on an interface. Syntax Parameters Defaults dampening [[[[half-life] [reuse-threshold]] [suppress-threshold]] [maxsuppress-time]] half-life Enter the number of seconds after which the penalty is decreased. The penalty decreases half after the half-life period expires. The range is from 1 to 30 seconds. The default is 5 seconds. reuse-threshold Enter a number as the reuse threshold, the penalty value below which the interface state is changed to “up”.
PAGE 682
NOTE: You cannot apply dampening on an interface that is monitoring traffic for other interfaces. Example Related Commands DellEMC(conf-if-te-1/10)# dampening 20 800 4500 120 DellEMC(conf-if-te-1/10)# ● clear dampening — clear the dampening counters on all the interfaces or just the specified interface. ● show interfaces dampening — display interface dampening information. default interface Reset a physical interface to its factory default settings.
PAGE 683
DellEMC(conf)# default interface tengigabitethernet 1/5 DellEMC(conf-if-te-1/5)# show config ! interface TenGigabitEthernet 1/5 no ip address shutdown Related Commands ● show running-config – display the current configuration. description Assign a descriptive text string to the interface. Syntax description desc_text To delete a description, use the no description command. Parameters Defaults desc_text Enter a text string up to 240 characters long.
PAGE 684
● Entering a text string after the description command overwrites any previous text string that you previously configured as the description. ● The shutdown and description commands are the only commands that you can configure on an interface that is a member of a port-channel. ● Use the show interfaces description command to display descriptions configured for each interface. duplex (10/100 Interfaces) Configure duplex mode on the Management Interface interfaces where the speed is set to 10/100.
PAGE 685
disable stack-unit phy temp polling Disable physical temperature polling for 10GBase-T optical ports. Syntax disable stack-unit unit-number port port-number phy temp polling To enable physical temperature polling, use the enable stack-unit unit-number port portnumber phy temp polling command. Parameters stack-unit unitnumber Enter the keyword stack-unit then the unit-numberfor which you want to disable temperature polling. The range is from 1 to 6.
PAGE 686
enable stack-unit transceiver Enable the 10GBase-T optical port that is reset due to high temperature to normal mode. Syntax enable stack-unit unit-number port port-number transceiver Parameters stack-unit unit- number Enter the keyword stack-unit then the unit-number for which you want to enable temperature polling. The range is from 1 to 6. port port-number Enter the keyword port then the port-number for which you want to enable temperature polling. The range is from 1 to 48.
PAGE 687
errdisable recovery cause Enable automatic recovery of an interface from the Err-disabled state. Syntax errdisable recovery cause {bpduguard | fefd | maclearnlimit | arpinspection} To disable the automatic recovery, use the no errdisable recovery cause {bpduguard | fefd | maclearnlimit | arp-inspection} command. Parameters Defaults bpduguard Enter the keyword bpduguard to enable the timer to recover the interface from BPDU Guard error.
PAGE 688
Usage Information Version Description 9.14(0.0) Introduced on the platforms S4048–ON, S6100–ON, Z9100–ON, S4048T-ON, S3048–ON, S6000, S6010–ON, S5048F-ON, FN-IOM, and MXL. 9.13(0.2P2) Introduced on the S3100. Whenever the Err-disable recovery timer is reconfigured, it will get effective only after the current timer expires.
PAGE 689
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.0.0 Added support for the negotiate feature on the S4810 and S4820T. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 690
Example Example (Monitor Session) DellEMC(conf-if-Te-1/1)# show config ! interface TenGigabitEthernet 1/1 no ip address switchport no negotiation auto flowcontrol rx off tx on no shutdown ... DellEMC(conf-if-te-1/5)#show config ! interface TenGigabitEthernet 1/5 no ip address shutdown flowcontrol monitor 5 Example (Values) This Example shows how Dell EMC Networking OS negotiates the flow control values between two Dell EMC Networking chassis connected back-to-back using 1G copper ports.
PAGE 691
interface Configure a physical or virtual interface on the switch. Syntax Parameters Defaults interface interface interface Enter one of the following keywords and the interface information: ● For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0. ● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 692
Usage Information You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport. To place an interface in Layer 2 mode, ensure that the interface’s configuration does not contain an IP address and enter the switchport command. You can create up to 64 tunnel interfaces. The tunnel is added as a logical interface with no default configuration. To delete a tunnel interface, use the no interface tunnel tunnel-id command.
PAGE 693
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. The interface group command will create all the non-existent VLANs specified in the range. On successful command execution, the CLI switches to the interface group context.
PAGE 694
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Example Related Commands DellEMC(conf)# interface loopback 1655 DellEMC(conf-if-lo-1655)# ● ● ● ● interface interface interface interface — configure a physical interface. null — configure a Null interface.
PAGE 695
Usage Information Example Related Commands Version Description 6.4.1.0 Introduced You cannot delete a Management port. The Management port is enabled by default (no shutdown). To assign an IP address to the Management port, use the ip address command. DellEMC(conf)# interface managementethernet 1/1 DellEMC(conf-if-ma-1/1)# ● management route — configure a static route that points to the Management interface or a forwarding router.
PAGE 696
Example Related Commands DellEMC(conf)# interface null 0 DellEMC(conf-if-nu-0)# ● ● ● ● ● interface — configure a physical interface. interface loopback — configure a Loopback interface. interface port-channel — configure a port channel. interface vlan — configure a VLAN. ip unreachables — enable generation of internet control message protocol (ICMP) unreachable messages.
PAGE 697
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 698
Use the show running-config command to display the VLAN and port-channel interfaces. VLAN or port-channel interfaces that are not displayed in the show running-config command cannot be used with the bulk configuration feature of the interface range command. You cannot create virtual interfaces (VLAN, Port-channel) using the interface range command. NOTE: If a range has VLAN, physical and port-channel interfaces, only commands related to physical interfaces can be bulk configured.
PAGE 699
interface range macro (define) Defines a macro for an interface range and then saves the macro in the running configuration. Syntax Parameters define interface range macro name interface , interface , ... name Enter up to 16 characters for the macro name. interface, interface,... Enter the keywords interface range and the interface information. Select the range of interfaces for bulk configuration. You can enter up to six comma-separated ranges. Spaces are not required between the commas.
PAGE 700
Example (Single Range) This example shows how to define an interface range macro named test. Execute the show runningconfig command to display the macro definition.
PAGE 701
Example (Single Range) This example shows the macro named test that was defined earlier. DellEMC(config)# interface range macro test DellEMC(config-if-range-te-1/1-3,te-5/1-47,te-2/1-89)# Dell Related Commands ● interface range — configure a range of command (bulk configuration). ● interface range macro (define) — define a macro for an interface range (bulk configuration). interface vlan Configure a VLAN. You can configure up to 4094 VLANs.
PAGE 702
Example (Single Range) Related Commands DellEMC(conf)# int vlan 3 DellEMC(conf-if-vl-3)# ● ● ● ● ● ● ● ● interface — configure a physical interface. interface loopback — configure a loopback interface. interface null — configure a null interface. interface port-channel — configure a port channel group. show vlan — display the current VLAN configuration on the switch. shutdown — disable/enable the VLAN. tagged — add a Layer 2 interface to a VLAN as a tagged interface.
PAGE 703
keepalive Send keepalive packets periodically to keep an interface alive when it is not transmitting data. Syntax keepalive To stop sending keepalive packets, use the no keepalive command. Defaults Enabled. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 704
● For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 705
Example (Single Interface) Key Description l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis. a Change the view to the previous interface on the line card, or if in line card mode, the previous line card in the chassis. T Increase the screen refresh rate. t Decrease the screen refresh rate. q Return to the CLI prompt. systest-3 Monitor time: 00:00:06 Refresh Intvl.
PAGE 706
Te 1/22 Up 17304741100 3157554 10102508511 1114221 Te 1/23 Up 17304769659 3139507 7133354895 523329 m - Change mode c - Clear screen b - Display bytes r - Display pkts/bytes per sec l - Page up a - Page down mtu Set the link maximum transmission unit (MTU) (frame size) for an Ethernet interface. Syntax mtu value To return to the default MTU value, use the no mtu command. Parameters Defaults value Enter a maximum frame size in bytes. The range is from 592 to 9216.
PAGE 707
● All members must have the same link MTU value and the same IP MTU value. ● The port channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the channel members. For example, if the members have a link MTU of 2100 and an IP MTU 2000, the port channel’s MTU values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU. VLANs: ● All members of a VLAN must have same IP MTU value. ● Members can have different Link MTU values.
PAGE 708
Usage Information Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits.
PAGE 709
ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interfaces" counters 00:12:42 Queueing strategy: fifo Input Statistics: ... User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces.
PAGE 710
port-delay-restore (Configuration Mode) Allows a delayed bring up of all interfaces during switch boot up. Syntax port-delay-restore value To return to the default value, use the no port-delay-restore command. Parameters Defaults value Enter a timer value from 1 second to 300 seconds. Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 711
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. The following describes the interface command shown in the following example.
PAGE 712
Parameters Defaults seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds. NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value. For example, if 44 seconds is designated, it rounds to 30; 45 to 59 seconds rounds to 45. 299 seconds Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 713
entire buffer is cleared; the show int stats command shows the rate information to be 0 as the polling interval is less than 5. Defaults 299 seconds Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on all Dell EMC Networking OS platforms.
PAGE 714
Example Version Description pre-Version 6.2.1.0 Introduced on the E-Series. DellEMC(conf-if-fo-1/49)# show config ! interface fortyGigE 1/49 no ip address mtu 9216 switchport no shutdown DellEMC(conf-if-fo-1/49)# DellEMC(conf-if-te-1/50)# show config ! interface Tengigabitethernet 1/50 no ip address mtu 9216 switchport no shutdown DellEMC(conf-if-te-1/50)# show config (from INTERFACE RANGE mode) Display the bulk configured interfaces (interface range).
PAGE 715
Example DellEMC(conf)# interface range tengigabitethernet 1/1 - 2 DellEMC(conf-if-range-gi-1/1-2)# show config ! interface TenGigabitEthernet 1/1 no ip address switchport no shutdown ! interface TenGigabitEthernet 1/2 no ip address switchport no shutdown DellEMC(conf-if-range-gi-1/1-2)# show interfaces Display information on a specific physical interface or virtual interface.
PAGE 716
Version Description 9.11(0.0) Included the FEC BER details in the output for 100G interfaces of S6100–ON and Z9100–ON. Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000-ON, S6100, Z9500, S6010, and Z9100. Included display information about EEE on the S3048–ON. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. Included display information about EEE on the S3100 series, S4820T, and S5000. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 717
Line Description TenGigabitEther net 1/1... Interface type and administrative and line protocol status. Hardware is... Interface hardware information, assigned MAC address, and current address. Pluggable media present... Present pluggable media wavelength, type, and rate.
PAGE 718
Line Description ○ wred=count both packets discarded in the MAC and in the hardware-based queues Rate information... Estimate of the input and output traffic rate over a designated interval (30 to 299 seconds). Traffic rate is displayed in bits, packets per second, and percent of line rate. Time since... Elapsed time since the last interface status change (hh:mm:ss format).
PAGE 719
Pluggable media present, SFP type is 1000BASE-SX Wavelength is 850nm Interface index is 100974648 Port will not be disabled on partial SFM failure Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit Flowcontrol rx on tx on ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1w0d5h Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 0 Vlans 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0
PAGE 720
Virtual-IP is not set Virtual-IP IPv6 address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example (OpenFlow instance) Related Commands DellEMC# show in
PAGE 721
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Changed the organization of the display output.
PAGE 722
for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interfacetype 1/1 - 4. ● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport].
PAGE 723
Related Commands ● dampening — configure dampening on an interface. ● show interfaces configured — display any interface with a non-default configuration. show interfaces phy Display auto-negotiation and link partner information. Syntax Parameters show interfaces gigabitethernet slot/port phy tengigabitethern et Enter the keyword tengigabitethernet then the slot or port information. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 724
AutoNegotiation Advertise Displays the control words the local interface advertises during negotiation. Duplex is either half or full. Asym- and Sym Pause is the types of flow control the local interface supports. AutoNegotiation Displays the control words the remote interface advertises during negotiation. Remote Partner’s Duplex is either half or full. Asym- and Sym Pause is the types of flow control Ability the remote interface supports.
PAGE 725
Asym Pause: False Sym Pause: False AutoNegotiation Expansion: ParallelDetectionFault: False ... show interfaces stack-unit Display information on all interfaces on a specific S-Series or Z-Series stack member. Syntax Parameters show interfaces stack-unit unit-number unit-number Enter the stack member number. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 726
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 727
Example Version Description 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.
PAGE 728
NOTE: This command also enables you to view information corresponding to a range of ports. ● For physical interfaces, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interfacetype 1/1 - 4. ● For port–channel interfaces, you can specify multiple ports as port-range.
PAGE 729
Items Description Vlan membership Lists the VLANs to which the interface is a member. Starting with Dell EMC Networking OS version 7.6.1, this field can display native VLAN membership by the port. Example DellEMC# show interfaces switchport Name: TenGigabitEthernet 1/1 802.1QTagged: Hybrid Vlan membership: Vlan 2, Vlan 20 Native VlanId: 20 Name: TenGigabitEthernet 1/2 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/3 802.
PAGE 730
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000-ON, S6100, Z9500, S6010, and Z9100. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 731
Line Description RX Power High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 732
Line Description Tx Power Present Tx power of the SFP. If this crosses Tx power alarm/warning thresholds, the Tx power high alarm/warning flag is set to true. If it falls below the low alarm/ warning thresholds, the Tx power low alarm/ warning flag is set to true. Rx Power Present receiving (Rx) power of the SFP. This value is either average Rx power or OMA. This depends on the Rx Power measurement type displayed above.
PAGE 733
Line Description Temperature Low This can be either true or false, depending on the Current Temperature value Warning Flag displayed above. Example Voltage Low Warning Flag This can be either true or false, depending on the Current Voltage value displayed above. Tx Bias Low Warning Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power Low Warning Flag This can be either true or false, depending on the Current Tx power value displayed above.
PAGE 734
SFP 1 Tx Bias Current = 6.894mA SFP 1 Tx Power = 0.328mW SFP 1 Rx Power = 0.
PAGE 735
● You can specify multiple ports as port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1 - 4.
PAGE 736
Example Related Commands DellEMC(conf-if-range-te-2/2,fo-2/56)# show range 2/2 - 0 2/56 - 0 DellEMC(conf-if-range-te-2/2,fo-2/56)# ● interface — configure a physical interface on the switch. ● show ip interface — display Layer 3 information about the interfaces. show running-config ecmp-group Display interfaces, LAG, or LAG link bundles being monitored for uneven traffic distribution using the ecmp-group monitoring enable command.
PAGE 737
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(1.0) Introduced on the Z9100-ON. Example DellEMC#show system stack-unit 1 fanout configured Configured fan out ports in stack-unit 1 Configured Present 49 49 50 50 51 51 52 52 53 53 54 54 shutdown Disable an interface. Syntax shutdown To activate an interface, use the no shutdown command. Defaults The interface is disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 738
command on a port channel disables all traffic on the port channel and the individual interfaces within the port channel. To enable a port channel, enter no shutdown on the port channel interface and at least one interface within that port channel. The shutdown and description commands are the only commands that you can configure on an interface that is a member of a port channel. Related Commands ● interface port-channel — create a port channel interface. ● interface vlan — create a VLAN.
PAGE 739
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Supported on LC-EH-GE-50P or the LC-EJ-GE-50P cards. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This command is found on the /1000/10000 Base-T Ethernet interfaces.
PAGE 740
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810 8.1.1.0 Introduced on the E-Series. 7.5.1.
PAGE 741
[confirm yes/no]:yes Quad mode is enabled on stack-unit 1 port 49 Dell(conf)#Jan 1 13:37:01: %STKUNIT1-M:CP %IFMGR-5-DYNAMIC_FANOUT: Port 49 in slot 1 has been fanned-out TenGigabitEthernet 1/49/1 unassigned NO Manual administratively down down TenGigabitEthernet 1/49/2 unassigned NO Manual administratively down down TenGigabitEthernet 1/49/3 unassigned NO Manual administratively down down TenGigabitEthernet 1/49/4 unassigned NO Manual administratively down down switchport Place an interface in Layer 2 mod
PAGE 742
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.1.0 Added support for port-channel interfaces (the port-channel number option). 8.3.7.
PAGE 743
If you configure the wavelength on a non-tunable optic, there is no change to the existing wavelength. The configured wavelength is saved in the running configuration and is applicable, when a tunable optic is used. If you do not configure the wavelength on an inserted tunable optic, the existing wavelength is used. Example The following example shows the wavelength set for a tunable 10–Gigabit SFP+ optic: DellEMC(conf-if-te-1/1)# wavelength Related Commands 1528.
PAGE 744
application (for HTTP and ICMP) Configure the management egress interface selection for HTTP and ICMP. NOTE: Only the options that have been newly introduced are described here. For a complete description on all of the keywords and variables that are available with this command, refer the respective Command Reference Guide of the applicable platform of the Release 9.2(0.0) documentation set.
PAGE 745
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 746
----------10.11.0.0/16 172.16.1.0/24 ------ManagementEthernet 1/1 10.11.192.4 ----Connected Active -----------Connected Static show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Syntax show management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 747
Example DellEMC# show management application pkt-fallback-cntr dns : 0 ftp : 0 ntp : 0 radius : 0 sflow-collector : 0 snmp : 0 ssh : 2 syslog : 0 tacacs : 0 telnet : 0 tftp : 0 Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a Port Channel. ● The platform supports 128 port channels and 16 members per port channel.
PAGE 748
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 749
port-channel number Defaults Enter the keywords port-channel then an existing LAG number. Enter this keyword/variable combination twice, identifying the two paired LAGs. None Command Modes PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 750
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series. 7.6.1.0 Introduced on S-Series. 7.5.1.
PAGE 751
Parameters Defaults number Enter the number of links in a LAG that must be in “oper up” status. The range is from 1 to 16. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 752
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 753
Example Version Description pre-Version 6.2.1.0 Introduced on the E-Series. DellEMC(conf-if-po-1)# show config ! interface Port-channel 1 no ip address shutdown DellEMC(conf-if-po-1)# show interfaces port-channel Display information on configured Port Channel groups. ` Syntax Parameters show interfaces port-channel [channel-number] [brief] [description] channel-number For a Port Channel interface, enter the keyword port-channel then a number. The range is from 1 to 128.
PAGE 754
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Modified to display the LAG failover group status. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example 754 Interfaces The following describes the show interfaces port-channel command shown in the following example. Field Description Port-Channel 1... Displays the LAG’s status.
PAGE 755
Members in this channel: Te 2/5 Te 2/18 ARP type: ARPA, ARP timeout 04:00:00 Last clearing of "show interfaces" counters 00:00:00 Queueing strategy: fifo 44507301 packets input, 3563070343 bytes Input 44506754 IP Packets, 0 Vlans 0 MPLS 41 64-byte pkts, 44502871 over 64-byte pkts, 249 over 127-byte pkts 407 over 255-byte pkts, 3127 over 511-byte pkts, 606 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 1218120 packets output, 10
PAGE 756
Parameters outgoing-portchannel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information. ● For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. incominginterface Enter the keywords incoming-interface then the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 757
The output displays three entries: ● Egress port for unfragmented packets. ● In the event of fragmented packets, the egress port of the first fragment. ● In the event of fragmented packets, the egress port of the subsequent fragments. NOTE: In the show port channel flow command output, the egress port for an unknown unicast, multicast, or broadcast traffic is not displayed.
PAGE 758
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7.0.0 Introduced on the S5000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S Series. 7.6.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 759
Usage Information Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.1.1.0 Introduced. If the TDR test has not been run, an error message is generated: %Error: Please run the TDR test first The following describes the TDR test status. Example Related Commands Status Definition OK Status: Terminated TDR test is complete, no fault is detected on the cable, and the test is terminated.
PAGE 760
Defaults Debug disabled. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.
PAGE 761
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series.
PAGE 762
ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 763
24 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: ● Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 764
● md5 — Use Message Digest 5 (MD5) authentication. ● sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. ● null — Causes an encryption policy configured for the area to not be inherited on the interface. Defaults espauthentication Enter the keywords esp-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. ● md5 — Use Message Digest 5 (MD5) authentication.
PAGE 765
Parameters Defaults name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.
PAGE 766
match Apply an match filter to the crypto policy. Syntax match seq-num tcp [sourceip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] To remove the match filter for the crypto map, use the no match seq-num tcp [source ip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] command. Parameters seq-num Enter the match command sequence number.
PAGE 767
session-key Specify the session keys used in the crypto policy entry. Syntax session-key {inbound | outbound} {ah spi hex-key-string | esp spi encrypt hex-key-string auth hex-key-string To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters Defaults name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec.
PAGE 768
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500. DellEMC# show crypto ipsec transform-set Transform-Set Name Transform-Set refCnt AH Transform ESP Auth Transform ESP Encry Transform DellEMC# : dallas : 0 : : : 3des show crypto ipsec policy Display the crypto policy configuration.
PAGE 769
Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num : : : : : : : : 1.1.1.1 /32 0 1.1.1.2 /32 23 DellEMC(conf-crypto-policy)# transform-set Specify the transform set the crypto policy uses. Syntax transform-set transform-set-name To delete a transform set from the crypto policy, use the no transform-set transform-setname command.
PAGE 770
25 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 771
• • • • • • show show show show show show ip protocols ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters Defaults vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 772
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid. You can use the vrf attribute of this command to create a static ARP entry on either a default or a non-default VRF.
PAGE 773
Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands ● show arp retries — display the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
PAGE 774
Parameters Defaults vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows. max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 775
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart. Related Commands ● show arp retries — display the configured number of ARP retries. arp timeout Set the time interval for an ARP entry to remain in the ARP cache.
PAGE 776
Version Description pre-6.2.1.1 Introduced on the E-Series. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM). Syntax clear arp-cache [vrf vrf-name | interface | ip ip-address] [no-refresh] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear the ARP cache corresponding to that VRF.
PAGE 777
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 778
clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.) Syntax clear ip fib stack-unit unit-number vrf vrf-name Parameters unit-number Enter the number of the stack unit. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all FIB entries corresponding to that VRF. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 779
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 780
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 781
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 782
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.
PAGE 783
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 784
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series.
PAGE 785
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 786
Field Description UDP src= Displays the source and destination ports for the UDP packets. ICMP type= Displays the ICMP type and code. IP Fragment States that it is a fragment and displays the unique number identifying the fragment (Ident) and the offset (in 8-byte units) of this fragment (fragment offset) from the beginning of the original datagram. Example Usage Information IP: s=10.1.2.62 (local), d=10.1.2.
PAGE 787
icmp6-redirect enable Enable ICMP and ICMP6 redirects. Syntax icmp6-redirect enable Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description Legacy command Legacy command Usage Information Use this command to notify hosts on the same network that a better route is available for a specific destination.
PAGE 788
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You must be in INTERFACE mode before you add an IP address to an interface. Assign an IP address to an interface prior to entering ROUTER OSPF mode. ip directed-broadcast Enables the interface to receive directed broadcast packets.
PAGE 789
ip domain-list Configure names to complete unqualified host names. Syntax ip domain-list name To remove the name, use the no ip domain-list name command. Parameters Defaults name Enter a domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 790
ip domain-lookup To address resolution (that is, DNS), enable dynamic host-name. Syntax ip domain-lookup To disable DNS lookup, use the no ip domain-lookup command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 791
To remove the domain name, use the no ip domain-name command. Parameters Defaults name Enter one domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 792
Parameters Defaults ip-address Enter an IP address in dotted decimal format (A.B.C.D). Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 793
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 794
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 795
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 796
● ● ● ● ● Defaults NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
PAGE 797
ip max-frag-count Set the maximum number of fragments allowed in one packet for packet re-assembly. Syntax ip max-frag-count count To place no limit on the number of fragments allowed, use the no ip max-frag-count command. Parameters Defaults count Enter a number for the number of fragments allowed for re-assembly. The range is from 2 to 256. No limit is set on number of fragments allowed. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 798
max-number Defaults Enter the maximum number of protocol routes that a VRF RTM can hold. The range is from 0 to 7500. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(2.0) Introduced on the S3100 series. 9.4.(0.0) Introduced on the S4810 and S4820T.
PAGE 799
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell EMC Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out on all other interfaces, including the Management port. You can separately configure both IPv4 and IPv6 domain name servers.
PAGE 800
Related Commands ● show ip interface — display the interface routing status and configuration. ip route Assign a static route to the switch. Syntax ip route [vrf vrf-name] ip-address mask {ip-address | interface [ipaddress]} [distance] [name description] [permanent] [tag tag-value] [vrf vrf-name] [weight weight-value] To delete a specific static route, use the no ip route destination mask command. To delete all routes matching a certain route, use the no ip route destination mask command.
PAGE 801
vrf vrf-name Enter the keyword vrf followed by the name of the VRF. Use this VRF option after the next hop to specify which VRF the next hop belongs to. This setting is used in route leaking cases. See “R”oute Leaking VRFs” in the Virtual Routing and Forwarding (VRF) section of the Configuration guide. weight weight- Enter the keyword weight followed by a weight value. The range is from 0 to 255.
PAGE 802
● When recursive resolution is satisfied, Dell EMC Networking OS re-installs the route. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect. Also, if a path corresponding to a static route (destination) has a non-zero weight assigned to it and other paths do not have any weight configured, then regular ECMP is used for forwarding.
PAGE 803
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages. Syntax ip unreachables To disable the generation of ICMP messages, use the no ip unreachables command. Defaults Disabled.
PAGE 804
load-balance By default, for C-Series and S-Series, Dell EMC Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 805
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Added the ingress-port parameter for the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 806
Defaults | source-destmac ] ● ● ● ● tunnel [ ipv4over-ipv4 | ipv4over-gre-ipv4 | mac-in-mac ]} To use tunnel key fields in hash computation, enter the keyword tunnel then one of the parameters: ● ipv4-over-ipv4 — Use ipv4-over-ipv4 field in hash calculation. ● ipv4-over-gre-ipv4 — Use ipv4-over-gre-ipv4 field in hash calculation. ● mac-in-mac — Use mac-in-mac field in hash calculation. dest-module-id — Use dest-module-id field in hash calculation. vlan — Use vlan field in hash calculation .
PAGE 807
NOTE: The :: notation specifies successive hexadecimal fields of zeros. forwardingrouter-address Enter an IP address (dotted decimal format) or an IPv6 address (x:x:x:x::x format) of a forwarding router. managementethe Enter the keyword managementethernet for the Management interface on the rnet Primary RPM. Defaults fortyGigE Enter the keyword fortyGigE to specify a forty Gigbit Ethernet interface. vlan Enter the keyword vlan to specify a vlan interface.
PAGE 808
show arp Display the ARP table. Syntax show arp [vrf vrf-name] [interface interface | ip ip-address [mask] | macaddress mac-address [mac-address mask]] [retries] [static | dynamic] [inspection {database | statistics][summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF. NOTE: Use this attribute to start a BGP instance for either a specific address family corresponding to the default VRF or an IPv4 address family corresponding to a non-default VRF.
PAGE 809
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF and added usage information for the clear arp-cache command. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.
PAGE 810
Internet Internet Example (Private VLAN) 192.2.1.246 1 192.2.1.245 1 00:00:c0:02:01:02 00:00:c0:02:01:02 Te 2/13 Te 2/13 - CP CP NOTE: In this example, Line 1 shows community VLAN 200 (in primary VLAN 10) in a PVLAN. Line 2 shows primary VLAN 10. DellEMC# show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU --------------------------------------------------------------Internet 5.5.5.1 - 00:01:e8:43:96:5e Vl 10 pv 200 Internet 5.5.5.10 - 00:01:e8:44:99:55 Vl 10 Internet 10.1.2.
PAGE 811
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced. ● arp retries — set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. show hosts View the host table and DNS configuration.
PAGE 812
Field Description Default domain... Displays the domain name (if configured). Name/address lookup... States if DNS is enabled on the system. ● If DNS is enabled, the Name/Address lookup is domain service. ● If DNS is not enabled, the Name/Address lookup is static mapping Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address.
PAGE 813
[ecmp-group detail]] ● Enter the keyword ecmp-group detail to view the ECMP group index. ecmp-group {detail | memberinfo [detail [group-index index-number ]]} (OPTIONAL) Enter the keyword ecmp-group then one of the following keywords to filter results. ● Enter the keyword detail to view the ECMP group index. ● Enter the keyword member-info to view the member information for the ECMP group. ● Enter the keyword member-info detail to view detailed ECMP membership and n-hop information.
PAGE 814
Example DellEMC# show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port --------------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Te 3/44 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP 1.1.1.0/24 0 1 0 00:00:00:00:00:00 CP DellEMC# Example (ECMPGroup) DellEMC# show ip cam stack-unit 3 po 0 ecmp-group detail Destination EC C VId Mac-Addr Port ECMP Group-Index -------------------------------------------------------------------------1.1.
PAGE 815
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 816
The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp weighted command. Related Commands ● clear ip fib stack-unit — clear FIB entries on a specified stack-unit. ● ip ecmp weighted— enable weighted ECMP calculations. show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface.
PAGE 817
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command provides egress port information for a given IP flow. This information is useful in identifying which interface the packet follows in the case of Port-channel and Equal Cost Multi Paths. Use this command for routed packed only.
PAGE 818
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Updated the command output to include the unicast reverse path forwarding (uRPF) status. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 819
IP unicast RPF check is not supported DellEMC# DellEMC#show ip interface vlan 1 Vlan 1 is down, line protocol is down Internet address is not set IP MTU is 1500 bytes Directed broadcast forwarding is disabled Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# Usage Information Example (Brief) The following describes the show ip interface brief command shown in the following examp
PAGE 820
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 821
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.
PAGE 822
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Regular evaluation optimization enabled/disabled added to display output. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Example DellEMC# show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.
PAGE 823
NOTE: bgp, isis, ospf, and rip. ● If you enter bgp, you can include the BGP as-number . ● If you enter isis, you can include the ISIS routing-tag. ● If you enter ospf, you can include the OSPF process-id. process-id (OPTIONAL) Specify that only OSPF routes with a certain process ID must be displayed. routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes.
PAGE 824
Field Description ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● C = connected S = static R = RIP B = BGP IN = internal BGP EX = external BGP LO = Locally Originated O = OSPF IA = OSPF inter area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes The weight for weighted ECMP route calculations is displayed for each path
PAGE 825
Route Source Active Routes Non-active Routes connected 2 0 static 1 0 Total 3 0 Total 3 active route(s) using 612 bytes R1_E600i>show ip route static ? | Pipe through a command R1_E600i>show ip route static Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------*S 0.0.0.0/0 via 10.10.91.
PAGE 826
C C 4.4.4.0/24 6.6.6.0/24 6.6.6.2, via Te 1/16 Direct, Te 1/4 Direct, Te 1/16 0/0 0/0 00:01:32 00:01:25 DellEMC(conf)#do show ip route 1.1.1.0/24 Routing entry for 1.1.1.0/24 Known via "static", distance 1, metric 0 Last update 00:05:01 ago Routing Descriptor Blocks: * 4.4.4.2, via TenGigabitEthernet 1/4 * 6.6.6.2, via TenGigabitEthernet 1/16 DellEMC(conf)# show ip route list Display IP routes in an IP prefix list.
PAGE 827
Codes:C- connected, S - static, R - RIP, B- BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated, O- OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2- OSPF NSSA external type 2, E1 - OSPF external type 1, E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.
PAGE 828
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example. Column Heading Description Route Source Identifies how the route is configured in Dell EMC Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources.
PAGE 829
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 830
Keyword Definition ...short packets The number of bytes in the packet are too small. ...bad length The length of the packet was not correct. ...no port broadcasts The incoming broadcast/multicast packet did not have any listener. ...socket full The applications buffer is full and the incoming packet are dropped. The Dell Monitoring MIB provides access to the following statistics. ● IP Statistics: Bcast: Received: Object = f10BcastPktRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.
PAGE 831
cp Enter the keyword cp to view only TCP information from the Control Processor. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 832
Field Description Sent: Displays the total number of TCP packets sent and the number of urgent packets sent. 25 control packets... Displays the number of control packets sent and the number retransmitted. 11603 data packets... Displays the number of data packets sent. 24 data packets retransmitted Displays the number of data packets resent. 355 ack.. Displays the number of acknowledgement packets sent and the number of packet delayed. 0 window probe...
PAGE 833
26 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 834
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 835
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 836
-- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 837
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Added the monitor option.
PAGE 838
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 839
Defaults deny Enter the keyword deny to configure a filter to drop packets meeting this condition. ospfv3 Specify that this ACL is for OSPFv3 control plane traffic All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 840
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 841
cam-acl Allocate space for IPv6 ACLs. Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: ● L3 ACL (ipv4acl): 6 ● L2 ACL(l2acl): 5 ● IPv6 L3 ACL (ipv6acl): 0 ● L3 QoS (ipv4qos): 1 ● L2 QoS (l2qos): 1 l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 842
27 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 843
Command Modes CONFIGURATION Command History Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048–ON. 9.8(0.0P2) Introduced on the S3048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can partition the LPM table to store IPv6 prefixes greater than /64 mask length.
PAGE 844
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 845
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have. Syntax maximum dynamic-routes—ipv6 limit {warn-threshold threshold-value | warningonly} To remove the limit on the maximum number of IPv6 routes used, use the no maximum dynamicroutes-ipv6 command.
PAGE 846
ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface. Syntax ipv6 address autoconfig To disable the address autoconfig operation on the management interface, use the no ipv6 address autoconfig command. Default Disabled Command Modes INTERFACE (management interface only) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 847
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1(0.0) Updated Usage Information. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 848
To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address {ipv6-address prefix-length} eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 849
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ipv6 flowlabel-zero Configure system to set the flow label field in the packets to zero. Syntax ipv6 flowlabel-zero To disable the 0 from being set in the field and allow the protocol operations to fill the field, use the no ipv6 flowlabel-zero command. Default Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 850
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series. ipv6 name-server Enter up to six IPv6 addresses of name servers. The order you enter the addresses determines the order of their use.
PAGE 851
ipv6 nd dad attempts To perform duplicate address detection (DAD) on an interface, configure the number of neighbor solicitation messages that are sent. Syntax ipv6 nd dad attempts {number of attempts} To restore the default value, use the no ipv6 nd dad attempts command. Parameters Default number of attempts Enter the number of attempts to be made to detect a duplicate address. The range is from 0 to 15. Setting the value to 0 disables DAD on the interface.
PAGE 852
Parameters Defaults ipv6-RDNSSaddress Enter the IPv6 Recursive DNS Server’s (RDNSS) address. You can specify up to 4 IPv6 RDNSS server addresses. lifetime Enter the lifetime in seconds. The amount of time the IPv6 host can use the IPv6 RDNSS address for name resolution. The range is 0 to 4294967295 seconds. When you specify the maximum lifetime value of 4294967295 or infinite, the lifetime does not expire. A value of 0 indicates to the host that the RDNSS address should not be used.
PAGE 853
no-rtr-address Enter the keyword no-rtr-address to exclude the full router address from router advertisements (the R bit is not set). off-link Enter the keywords off-link to advertise the prefix without stating to recipients that the prefix is either on-link or off-link. valid-lifetime | infinite Enter the amount of time that the prefix is advertised, or enter infinite for an unlimited amount of time. The range is from 0 to 4294967295. The default is 2592000.
PAGE 854
ipv6 route Establish a static IPv6 route. Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [name description] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
PAGE 855
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.2) Added the keyword name for static routes. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 856
ipv6 unicast-routing Enable IPv6 unicast routing on the device. Syntax ipv6 unicast-routing To disable unicast routing, use the no ipv6 unicast-routing command. Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
PAGE 857
NOTE: If you do not specify this option, IPv6 CAM entries corresponding to the default VRF are displayed. unit-number Enter the stack unit’s ID number. port-set Enter the keyword Port Set. summary (OPTIONAL) Enter the keyword summary to display a table listing network prefixes and the total number prefixes which can be entered into the IPv6 CAM. index (OPTIONAL) Enter the index in the IPv6 CAM.
PAGE 858
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ● ipv6 flowlabel-zero — configure IPv6 address auto-configuration for the management interface. show ipv6 fib stack-unit View all FIB entries.
PAGE 859
show ipv6 flowlabel-zero Display the flow label zero setting. Syntax show ipv6 flowlabel-zero Default Disabled Command Modes EXEC Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 860
Defaults fortyGigE (OPTIONAL) View information for an IPv6 fortygigabitethernet interface. stack-unit id (OPTIONAL) View information for stacking. tunnel tunnel-id (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 860 IPv6 Basics This guide is platform-specific.
PAGE 861
ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 IPv6 unicast RPF check is not supported DellEMC# DellEMC# show ipv6 interface port-channel 128 Port-channel 128 is down, line protocol is down IPV6 is enabled Link Local address: fe80::201:e8ff:fe8a:e846 Global Unicast address(es): aabb::aa11, subnet is aabb::/64 (MANUAL) Remaining lifetime: infinite Global Anycast address(es): Joined Group address(es): ff02::1 ff02::2 ff02::1:ff00:aa11 ff02::1:ff8a:e846 ND MTU is 0 ICMP redirects are
PAGE 862
ff02::1 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds ND retransmit interval is 1000 milliseconds ND hop limit is 64 DellEMC# Example (Brief) Example (Tunnel) DellEMC# show ipv6 interface brief TenGigabitEthernet 1/2 [administratively down/down] fe80::201:e8ff:fea7:497e 2002:1:2::3/96 TenGigabitEthernet 1/12 [up/up] fe80::201:e8ff:fea7:497e 100::2/64 Man
PAGE 863
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. The following describes the show ipv6 mld-host command shown in the following example. Field Description Valid MLD Packets The total number of packets received and sent from the last time the elapsed time was cleared.
PAGE 864
Defaults bgp (OPTIONAL) View information for all IPv6 BGP routes. connected (OPTIONAL) View only the directly connected IPv6 routes. isis (OPTIONAL) View information for all IPv6 IS-IS routes. list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes. static (OPTIONAL) View only routes configured by the ipv6 route command.
PAGE 865
Field Description ● ● ● ● ● ● ● ● ● ● Example (SSeries) N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes Destination Identifies the route’s destination IPv6 address. Gateway Identifies whether the route is directly connected and on which interface the route is configured.
PAGE 866
trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults None Command Modes CONFIGURATION-POLICY-MAP-IN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 867
28 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 868
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters Defaults time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 869
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 870
Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 871
ip-address (Optional) Defaults Enter the ip-address that the iSCSI monitors. The ip-address specifies the IP address of the iSCSI target. 860, 3260 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 872
-----------------------------------------------iSCSI Targets and TCP Ports: -----------------------------------------------TCP Port Target IP Address 3260 860 Related Commands ● show iscsi session — display information about active iSCSI sessions on the switch. ● show iscsi session detailed — display detailed information about active iSCSI sessions on the switch. ● show run iscsi — show run iscsi. show iscsi session Display information about active iSCSI sessions on the switch.
PAGE 873
show iscsi session detailed Display detailed information on active iSCSI sessions on the switch. Syntax Parameters show iscsi session detailed [session isid] isid Enter the session’s iSCSi ID to display detailed information about the specified iSCSi session. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 874
Command History Related Commands 874 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 875
29 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 876
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 877
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
PAGE 878
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1.
PAGE 879
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain. ● isis password — configure an authentication password for an interface.
PAGE 880
tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 881
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command.
PAGE 882
debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies. Syntax debug isis [vrf vrf-name] adj-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name]adj-packets [interface] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details.
PAGE 883
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF. This information contains local updates tied to the VRF that you specify. This command displays the local LSP debugging details of the current unit.
PAGE 884
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 885
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced.
PAGE 886
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information.
PAGE 887
Usage Information Version Description 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. When you use this command to redistribute routes into a routing domain, the router becomes an autonomous system (AS) boundary router. An AS boundary router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one. How a metric value assigned to a default route advertises depends on the metric-style command configuration.
PAGE 888
distance Define the administrative distance for learned routes. Syntax distance weight [ip-address mask [prefix-list]] To return to the default values, use the no distance weight command. Parameters Defaults weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability. Routes with smaller values are given preference.) The default is 115.
PAGE 889
Parameters Defaults prefix-list-name Specify the prefix list to filter prefixes in routing updates. interface (OPTIONAL) Identifies the interface type and the interface following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 890
Defaults ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number. The range is from 1 to 65535. rip (OPTIONAL) Enter the keyword rip for RIP routes. static (OPTIONAL) Enter the keyword static for user-configured routing process. Not configured.
PAGE 891
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 892
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. Usage Information The domain password is inserted in Level 2 link state PDUs (LSPs), complete sequence number PDUs (CSNPs), and partial sequence number PDUs (PSNPs).
PAGE 893
network. A flag in the Restart TLV contains restart request (RR), restart acknowledge (RA) and suppress adjacency advertisement (SA) bit flags. The ISIS graceful restart-enabled router can co-exist in mixed topologies where some routers are graceful restart-enabled and others are not. For neighbors that are not graceful restart-enabled, the restarting router brings up the adjacency per the usual methods.
PAGE 894
Parameters Defaults seconds Enter the graceful restart time in seconds. The range is from 5 to 300 seconds. The default is 30 seconds. 30 seconds Command Modes ROUTER ISIS Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 895
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 896
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart t3 Configure the overall wait time before graceful restart completes. Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command.
PAGE 897
Related Commands ● graceful-restart restart-wait — enable the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | point-to-point] command.
PAGE 898
Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 899
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. IS-IS normally purges LSPs with an incorrect data link checksum causing the LSP source to regenerate the message. A cycle of purging and regenerating LSPs can occur when a network link continues to deliver accurate LSPs even though there is a link causing data corruption.
PAGE 900
NOTE: IP address is not mandatory for forming IS-IS adjacency. Related Commands ● net — configure an IS-IS network entity title (NET) for the routing process. ● router isis — enable the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process. Syntax ipv6 router isis [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters Defaults tag (OPTIONAL) This parameter is a unique name for a routing process.
PAGE 901
isis circuit-type Configure the adjacency type on interfaces. Syntax isis circuit-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no isis circuit-type command. Parameters Defaults level-1 You can form a Level 1 adjacency if there is at least one common area address between this system and neighbors. You cannot form Level 2 adjacencies on this interface.
PAGE 902
To return to the default values, use the no isis csnp-interval [seconds] [level-1 | level-2] command. Parameters Defaults seconds Interval of transmission time between CSNPs on multi-access networks for the designated intermediate system. The range is from 0 to 65535. The default is 10. level-1 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 1. level-2 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 2.
PAGE 903
Defaults seconds = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 904
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 905
Version Description 8.3.11.1 Introduced on the Z9000. Usage Information Hello PDUs are “padded” only when both the global and interface padding options are ON. Turning either one OFF disables padding for the corresponding interface. Related Commands ● hello padding — turn ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information.
PAGE 906
isis metric Assign a metric to an interface. Syntax isis metric default-metric [level-1 | level-2] To return to the default values, use the no isis metric [default-metric] [level-1 | level-2] command. Parameters default-metric Metric assigned to the link and used to calculate the cost from each other router via the links in the network to other destinations. You can configure this metric for Level 1 or Level 2 routing. The range is from 0 to 16777215 irrespective of the metric style. The default is 10.
PAGE 907
isis network point-to-point Enable the software to treat a broadcast interface as a point-to-point interface. Syntax isis network point-to-point To disable the feature, use the no isis network point-to-point command. Defaults Not enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 908
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 909
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. You can configure priorities independently for Level 1 and Level 2.
PAGE 910
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The IS-IS protocol automatically determines area boundaries and are able to keep Level 1 and Level 2 routing separate. Poorly planned use of this feature may cause configuration errors, such as accidental area partitioning.
PAGE 911
lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs). Syntax lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keywords level-1 to apply the configuration to generation of Level-1 LSPs.
PAGE 912
and there are no triggers for two times the maximum interval, fast behavior is restored (the initial wait time). lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 512 to 16000 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497.
PAGE 913
Parameters Defaults seconds The LSP refresh interval, in seconds. This value must be 300 seconds less than the value specified in the max-lsp-lifetime command. The range is from 1 to 65535 seconds. The default is 900. 900 seconds Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 914
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 915
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Change the maximum LSP lifetime with this command. The maximum LSP lifetime must always be greater than the LSP refresh interval. The seconds parameter enables the router to keep LSPs for the specified length of time. If the value is higher, the overhead is reduced on slower-speed links.
PAGE 916
Version Description 6.3.1.0 Introduced. metric-style To generate and accept old-style, new-style, or both styles of type, length, and values (TLV), configure a router. Syntax metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] To return to the default values, use the no metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] command. Parameters Defaults narrow Allows you to generate and accept old-style TLVs.
PAGE 917
Related Commands ● isis metric — configure a metric for an interface. multi-topology Enables multi-topology IS-IS. It also allows enabling/disabling of old and new style TLVs for IP prefix information in the LSPs. Syntax multi-topology [transition] To return to a single topology configuration, use the no multi-topology [transition] command. Parameters Defaults transition Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific.
PAGE 918
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 919
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 920
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 921
level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only. This setting is the default. metric metric- (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0.
PAGE 922
redistribute bgp 1 level-1 metric 32 metric-type external route-map rmap-isis-to-bgp redistribute ospf Redistribute routing information from an OSPF process.
PAGE 923
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command.
PAGE 924
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Configure a network entity title (the net command) to specify the area address and the router system ID. Enable routing on one or more interfaces to establish adjacencies and establish dynamic routing. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 925
overload bit in its LSPs, other routers ignore the unreliable router in their SPF calculations until the router has recovered. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 address. show config Display the changes you made to the IS-IS configuration. Default values are not shown. Syntax show config Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific.
PAGE 926
multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database. Syntax show isis [vrf vrf-name] database [level-1 | level-2] [local] [detail | summary] [system-id] [lspid] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IS-IS link state database corresponding to that VRF.
PAGE 927
Usage Information The following describes the show isis database command shown in the following example. Field Description IS-IS Level-1/ Level-2 Link State Database Displays the IS-IS link state database for Level 1 or Level 2. LSPID Displays the LSP identifier. The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID. If this byte is not zero, the LSP describes system links.
PAGE 928
Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 10 IPv6 (MT-IPv6) 1511::/64 Metric: 10 IPv6 (MT-IPv6) 2511::/64 Metric: 10 IPv6 (MT-IPv6) 1011::/64 Metric: 10 IPv6 1511::/64 Metric: 10 IP 10.1.1.0 255.255.255.0 Hostname: ISIS IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002D 0xB2CD 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.
PAGE 929
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 930
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. DellEMC# show isis hostname System Id Dynamic Name Static Name *F100.E120.
PAGE 931
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 932
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 933
MAC Address: 0000.0000.0000 Hold Time: 28 Link Local Address: fe80::201:e8ff:fe00:492c Topology: IPv4 IPv6 , Common (IPv4 IPv6 ) Adjacency being used for MTs: IPv4 IPv6 DellEMC# show isis protocol Display IS-IS routing information. Syntax Parameters show isis [vrf vrf-name] protocol vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS routing information corresponding to that VRF.
PAGE 934
Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode. DellEMC# show isis traffic This command allows you to display IS-IS traffic interface information. Syntax show isis [vrf vrf-name] traffic [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS traffic interface information corresponding to that VRF.
PAGE 935
Example Item Description Level-1/Level-2 Hellos (sent/ rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs. Level-1/Level-2 LSPs flooded (sent/rcvd) Displays the number of flooded LSPs sent and received. Level-1/Level-2 LSPs CSNPs (sent/ rcvd) Displays the number of CSNP LSPs sent and received.
PAGE 936
To restore default values, use the no spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keyword level-1 to apply the configuration to Level-1 SPF calculations. level-2 (OPTIONAL) Enter the keyword level-2 to apply the configuration to Level-2 SPF calculations. interval seconds Enter the maximum number of seconds between SPF calculations. The range is from 0 to 120 seconds.
PAGE 937
30 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 938
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 939
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 940
Defaults 1 second Command Modes INTERFACE (conf-if-po-number) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 941
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 942
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. port-channel-protocol lacp Enable LACP on any LAN port. Syntax port-channel-protocol lacp To disable LACP on a LAN port, use the no port-channel-protocol lacp command. Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 943
Defaults sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters. Without a Port Channel specified, the command clears all Port Channel counters. Command Modes ● EXEC ● EXEC Privilege Command History Example (Port-ChannelNumber) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 944
DellEMC# Example (Counter) Related Commands 944 DellEMC# show lacp 1 counters ---------------------------------------------------LACP PDU Marker PDU Unknown Illegal Port Xmit Recv Xmit Recv Pkts Rx Pkts Rx ----------------------------------------------------Te 1/6 200 200 0 0 0 0 DellEMC# ● clear lacp counters — clear the LACP counters. ● show interfaces port-channel — display information on configured Port Channel groups.
PAGE 945
31 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically.
PAGE 946
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 947
mac-address-table disable-learning Disable MAC address learning from LACP or LLDP BPDUs. Syntax Parameters Defaults mac-address-table disable-learning [lacp | lldp] lacp Enter lacp to disable MAC address learning from LACP BPDUs. lldp Enter LLDP to disable MAC address learning from LLDP BPDUs. Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 948
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 949
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. For information about the specific trap sent and the corresponding Syslog, see SNMP Traps. mac-address-table station-move refresh-arp Ensure that address resolution protocol (ARP) refreshes the egress interface when a station move occurs due to a topology change.
PAGE 950
mac learning-limit Limit the maximum number of MAC addresses (static + dynamic) learned on a selected interface. Syntax mac learning-limit address_limit [vlan vlan-id] [station-move-violation [dynamic]] [dynamic [no-station-move| station-move]] Parameters Defaults address_limit Enter the maximum number of MAC addresses that can be learned on the interface. The range is from 1 to 1000000. vlan vlan-id Enter the keyword then the VLAN ID. The range is from 1 to 4094.
PAGE 951
MAC Learning Limit violation logs and actions are not available on a per-VLAN basis. With the keyword no-station-move option, MAC addresses learned through this feature on the selected interface persist on a per-VLAN basis, even if received on another interface. Enabling or disabling this option has no effect on already learned MAC addresses. After the MAC address learning limit is reached, the MAC addresses do not age out unless you add the dynamic option.
PAGE 952
Version Description 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands ● show mac learning-limit — display details of the mac learning-limit. mac learning-limit mac-address-sticky Maintain the dynamically learned mac addresses as sticky MAC addresses on the selected port.
PAGE 953
mac learning-limit station-move-violation Specify the actions for a station move violation. Syntax mac learning-limit station-move-violation {log | shutdown-both | shutdownoffending | shutdown-original} To disable a configuration, use the no mac learning-limit station-move-violation command, then the configured keyword. Parameters Defaults log Enter the keyword log to generate a syslog message on a station move violation.
PAGE 954
mac learning-limit reset Reset the MAC address learning-limit error-disabled state. Syntax mac learning-limit reset Defaults none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 955
Usage Information Only if you enable the port security, you will be able to configure MAC address learning limit configurations on the interface level. When you disable the port security, all the interface level configurations are reset. Also, all dynamically learnt MAC addresses on the interfaces configured with MAC address learning limit are cleared. show cam mac linecard (count) Display the content addressable memory (CAM) size and the portions allocated for MAC addresses and for MAC ACLs.
PAGE 956
Parameters linecard slot (REQUIRED) Enter the keyword linecard then a slot number to select the linecard for which to gather information. port-set port- (REQUIRED) Enter the keywords port-set then a Port-Pipe number to select the Port-Pipe for which to gather information. The range is from 0 or 1. pipe address mac- addr (OPTIONAL) Enter the keyword address then a MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address.
PAGE 957
111 112 113 114 115 116 117 Dell# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00:01:e8:0d:b7:63 00:01:e8:0d:b7:62 00:01:e8:0d:b7:61 00:01:e8:0d:b7:60 00:01:e8:0d:b7:5f 00:01:e8:0d:b7:5e 00:01:e8:0d:b7:5d SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC DROP DROP DROP DROP DROP DROP DROP show mac-address-table Display the MAC address table.
PAGE 958
Usage Information Example Usage Information 958 Layer 2 Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Updated the output. 8.5.1.
PAGE 959
Example (Count) Related Commands Line Beginning With Description Dynamic Address... Lists the number of dynamically learned MAC addresses. Static Address... Lists the number of user-defined MAC addresses. Total MAC... Lists the total number of MAC addresses the switch uses.
PAGE 960
Example Version Description 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series and S-Series. pre-6.2.1.1 Introduced on the E-Series. DellEMC# show mac-address-table aging-time Mac-address-table aging time : 1800 DellEMC# Related Commands ● show mac-address-table — display the current MAC address configuration. show mac accounting destination Display destination counters for Layer 2 traffic (available on physical interfaces only).
PAGE 961
Example Dell-1# show mac accounting destination interface tengigabitethernet 2/1 Destination Out Port VLAN Packets Bytes 00:44:00:00:00:02 00:44:00:00:00:01 00:22:00:00:00:00 00:44:00:00:00:02 00:44:00:00:00:01 Te Te Te Te Te 1000 1000 1000 2000 2000 10000 10000 10000 10000 10000 11/1 11/1 11/1 11/1 11/1 5120000 5120000 5120000 5120000 5120000 Dell-1# Related Commands ● show mac accounting access-list — display the MAC access list configurations and counters (if configured).
PAGE 962
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Added support for the violate-action and detail options. 6.5.1.0 Added support for Port Channel.
PAGE 963
Usage Information Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 964
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced The no default vlan disable command is not listed in the running-configuration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters Defaults vlan-name Enter up to 32 characters as the name of the VLAN. Not configured.
PAGE 965
show config Display the current configuration of the selected VLAN. Syntax show config Command Modes INTERFACE VLAN Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 966
id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094. Only information on the VLAN specified is displayed. name vlan-name (OPTIONAL) Enter the keyword name then the name configured for the VLAN. Only information on the VLAN named is displayed. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 966 Layer 2 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 967
Column Heading Description ● ● ● ● ● ● ● ● ● Ports Example x (not capitalized x) for Dot1x untagged X (capitalized X) for Dot1x tagged o (not capitalized o) for OpenFlow untagged O (capitalized O) for OpenFlow tagged H for VSN tagged i (not capitalized i) for Internal untagged I (capitalized I) for Internal tagged v (not capitalized v) for VLT untagged V (capitalized V) for VLT tagged Displays the type, slot, and port information.
PAGE 968
Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 41 Status Description Q Ports Active T Te 1/47 DellEMC# show vlan id 42 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 42 DellEMC# Example (Brief) Example (Name) Status Description Q Ports Active U Te 1/47 DellEMC# show vlan br VLAN Name STG MAC Aging IP Address ---- --------
PAGE 969
● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults All interfaces in Layer 2 mode are untagged. Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific.
PAGE 970
Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Not configured. Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific.
PAGE 971
untagged Add a Layer 2 interface to a VLAN as an untagged interface. Syntax untagged interface To remove an untagged interface from a VLAN, use the no untagged interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 972
Far-End Failure Detection (FEFD) The Dell EMC Networking operating software supports far-end failure detection (FEFD) on the Ethernet interfaces of the platform. The FEFD feature detects and reports far-end link failures. ● FEFD is not supported on the Management interface. ● During an RPM failover, FEFD is operationally disabled for approximately 8 to 10 seconds. ● By default, FEFD is disabled. debug fefd Enable debugging of FEFD.
PAGE 973
fefd Enable Far-End Failure Detection on an interface, set the FEFD interval, or select the FEFD mode. Syntax fefd {disable|interval|mode {aggressive|normal} Parameters Defaults disable Enter the keyword disable to disable FEFD for the specified interface. interval Enter the keyword interval, followed by a value to specify the FEFD interval in seconds. Range is from 3 to 300. Default is 15. mode Enter the keyword mode followed by the mode type to specify the FEFD mode.
PAGE 974
To re-enable FEFD on an interface, use the no fefd disable command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 975
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information You can set up the interval between control packets using the fefd interval command.
PAGE 976
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. fefd reset Reset all interfaces or a single interface that was in “error-disabled” mode.
PAGE 977
fefd-global interval Configure an interval between FEFD control packets. Syntax fefd-global interval seconds To return to the default value, use the no fefd-global interval command. Parameters Defaults seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds. 15 seconds Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 978
When an interface is placed in “error-disabled” state, t enter the fefd reset command to reset the interface state. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 979
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 980
Related Commands 980 Layer 2 ● ● ● ● fefd — enable far-end failure detection. fefd disable — disable FEFD on an interface only. fefd-global — enable FEFD globally on the system. fefd reset — reset all interfaces or a single interface that was in “error-disabled” mode.
PAGE 981
32 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 982
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
PAGE 983
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor.
PAGE 984
Defaults systemdescription Enter the keywords system-description to advertise the system description TLVs to the LLDP peer. system-name Enter the keywords system-name to advertise the system name TLVs to the LLDP peer. None Command Modes CONFIGURATION (conf-lldp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.
PAGE 985
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the Z9000 and S4810. 8.3.19.0 Introduced on the S4820T. clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface.
PAGE 986
clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Syntax clear lldp neighbors [interface interface] Parameters interface interface Defaults (OPTIONAL)Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 987
Parameters interface interface Defaults Enter the following keywords and slot/port[/subport] or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. all Enter the keyword all to display information on all interfaces. events Enter the keyword events to display major events such as timer events.
PAGE 988
Dec 4 22:38:27 : 02 01 2c fe 05 aa bb cc 04 61 fa 01 40 00 00 Dec 4 22:38:28 : 00 00 00 00 00 00 00 00 c6 0f ba 27 Dec 4 22:38:28 : TLV: Chassis ID, Len: 7, Subtype: Mac address Value: 00:a0:c9:00:00:01 Dec 4 22:38:29 : TLV: Port ID, Len: 2, Subtype: Interface name Value: T Dec 4 22:38:29 : TLV: TTL, Len: 2, Value: 300 Dec 4 22:38:29 : TLV: UNKNOWN TLV, ORG_SPEC[aa-bb-cc, 4], Len: Value:a Dec 4 22:38:29 : aa bb cc 04 61 Dec 4 22:38:29 : 40 Dec 4 22:38:29 : TLV: UNKNOWN TLV, Type: 125 Len: 1, Value: @ Dec 4
PAGE 989
hello Configure the rate at which the LLDP control packets are sent to its peer. Syntax hello seconds To revert to the default, use the no hello seconds command. Parameters Defaults seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds. 30 seconds Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 990
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000 and S4810. To enable LLDP on the management interface, use the no disable command in LLDP-MANAGEMENTINTERFACE mode (conf-lldp-mgmtIf). mode To receive or transmit, set LLDP. Syntax mode {tx | rx} To return to the default, use the no mode command.
PAGE 991
multiplier Set the multiple of the hello timer before LLDP declares the interface dead. Syntax multiplier number To return to the default, use the no multiplier command. Parameters Defaults integer Enter the number of consecutive misses before the LLDP declares the interface dead. The range is from 2 to 10. 4 Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 992
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 993
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Before LLDP can be configured on an interface, it must be enabled globally from CONFIGURATION mode. This command places you in LLDP mode on the interface; it does not enable the protocol.
PAGE 994
Usage Information Example Example (Detail) Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval.
PAGE 995
38, 4) 48, 4) 58, 4) 68, 4) 78, 4) 88, 4) 98, 4) (108, (118, 4) ( 39, 4) ( 40, 4) ( 41, 4) ( 42, 4) ( 43, 4) ( 44, 4) ( 45, 4) ( 46, 4) ( 47, 4) ( ( 49, 4) ( 50, 4) ( 51, 4) ( 52, 4) ( 53, 4) ( 54, 4) ( 55, 4) ( 56, 4) ( 57, 4) ( ( 59, 4) ( 60, 4) ( 61, 4) ( 62, 4) ( 63, 4) ( 64, 4) ( 65, 4) ( 66, 4) ( 67, 4) ( ( 69, 4) ( 70, 4) ( 71, 4) ( 72, 4) ( 73, 4) ( 74, 4) ( 75, 4) ( 76, 4) ( 77, 4) ( ( 79, 4) ( 80, 4) ( 81, 4) ( 82, 4) ( 83, 4) ( 84, 4)
PAGE 996
Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet 1/1 Locally assigned remote Neighbor Index: 1 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-6
PAGE 997
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 998
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S8420T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 999
As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information. The Organizational Unique Identifier (OUI) for the Telecommunications Industry Association (TIA) is 00-12-BB. ● LLDP-MED Endpoint Device — any device that is on an IEEE 802 LAN network edge, can communicate using IP, and uses the LLDP-MED framework.
PAGE 1000
Related Commands Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● protocol lldp (Configuration) — enable LLDP globally. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med guest-voice-signaling To advertise a separate limited voice service for a guest user when the guest voice control packets use a separate network policy than the voice data, configure the system.
PAGE 1001
Related Commands ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system. Syntax advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} To return to the default, use the no advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} command.
PAGE 1002
advertise med power-via-mdi To advertise the Extended Power via MDI TLV, configure the system. Syntax advertise med power-via-mdi To return to the default, use the no advertise med power-via-mdi command. Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1003
priority-tagged number Defaults Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1004
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1005
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1006
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● ● debug lldp interface — debug LLDP.
PAGE 1007
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — de bug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system.
PAGE 1008
Related Commands 1008 Version Description 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 1009
33 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 1010
command in Global configuration mode. This setting causes the multicast MAC address to be mapped to the cluster IP address for NLB mode of operation of the switch. Related Commands ● clear arp-cache — clear dynamic ARP entries from the ARP table. ● show arp — display the ARP table.
PAGE 1011
Example (Multicast) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for multicast MAC address on the MXL platform.
PAGE 1012
34 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the S4048–ON platform.
PAGE 1013
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 1014
Version Description 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax clear ip msdp statistic peer peer-address Parameters Defaults peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer.
PAGE 1015
debug ip msdp Turn on MSDP debugging. Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters Defaults event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.).
PAGE 1016
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1017
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.0 Introduced If a list is not specified, all SA messages received from the default peer are accepted. You can enter multiple default peer commands.
PAGE 1018
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters Defaults name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1019
Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 1020
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. description name (OPTIONAL) Enter the keyword description then a description name (maximum 80 characters) to designate a description for the MSDP peer.
PAGE 1021
ip msdp redistribute Filter local PIM SA entries in the SA cache. SAs which the ACL denies time out and are not refreshed. Until they time out, they continue to reside in the MSDP SA cache. Syntax Parameters Defaults ip msdp redistribute [list acl-name] list acl-name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1022
Defaults peer-address Enter the peer address of the MSDP peer in a dotted decimal format (A.B.C.D.). access-list name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1023
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the E-Series.
PAGE 1024
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1025
Parameters Defaults peer peer address Enter the keyword peer then the peer address in a dotted decimal format (A.B.C.D.). sa-cache Enter the keywords sa-cache to display the Source-Active cache. summary Enter the keyword summary to display an MSDP peer summary. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1026
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example 1026 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1027
35 Multicast Listener Discovery Protocol Dell Networking OS Supports Multicast Listener Discovery (MLD) protocol. Multicast Listener Discovery (MLD) is a Layer 3 protocol that IPv6 routers use to learn of the multicast receivers that are directly connected to them and the groups in which the receivers are interested. Multicast routing protocols (like PIM) use the information learned from MLD to route multicast traffic to all interested receivers.
PAGE 1028
Joining a Multicast Group The Querier periodically sends a General Query to the all-nodes multicast address FF02::1. A host that wants to join a multicast group responds to the general query with a report that contains the group address; the report is also addressed to the group (in the IPv6 Destination Address field). To avoid duplicate reporting, any host that hears a report from another host for the same group in which it itself is interested cancels its report for that group.
PAGE 1029
| | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +. -+ . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Version 2 multicast listener reports are sent by IP nodes to report (to neighboring routers) the current multicast listening state, or changes in the multicast listening state, of their interfaces.
PAGE 1030
| | * Source Address [1] * | | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +-+ . . . . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Auxiliary Data . . .
PAGE 1031
To adjust the query response time, use the following command: INTERFACE Mode ipv6 mld query-max-resp-time Clearing MLD groups Clear a specific group or all groups on an interface from the multicast routing table. To clear MLD groups, use the following command: EXEC Privilege clear ipv6 mld groups Debugging MLD Display Dell Networking OS messages about the MLD process.
PAGE 1032
show ipv6 mld groups Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 Displaying MLD Interfaces Display MLD interfaces.
PAGE 1033
● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. group-address Defaults (OPTIONAL) Enter the group address in the following format: x:x:x:x::x. The :: notation specifies successive hexadecimal fields of zero. None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 1034
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping enable Enable MLD snooping on the switch globally. Syntax ipv6 mld snooping enable To disable MLD snooping, use the no ipv6 mld snooping enable command.
PAGE 1035
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1036
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. detail Defaults View detailed group information. None. Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 1037
MLD snooping last member query response interval is 1000 ms MLD snooping explicit tracking is disabled show ipv6 mld snooping mrouter Display information on the MLD snooping router. Syntax Parameters Defaults show ipv6 mld snooping mrouter [vlan] VLAN (OPTIONAL) Enter the keyword VLAN then the VLAN number to display the information on that specific VLAN. The VLAN range is from 1 to 4094. None. Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1038
36 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 1039
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1040
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● protocol spanning-tree mstp — enter MULTIPLE SPANNING TREE mode.
PAGE 1041
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● max-age — change the wait time before MSTP refreshes protocol configuration information. ● hello-time — change the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs).
PAGE 1042
● max-age — change the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults max-age Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1043
To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094. bridge-priority Enter the keywords bridge-priority then a value in increments of 4096 as the bridge priority. The range is from zero (0) to 61440.
PAGE 1044
Defaults No default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1045
This command is supported in all STP modes such as STP, RSTP, MSTP, and PVST. The command behavior does not change when a new member port is added to the port-channel or an existing member port is deleted from the configuration. The path cost reflects the cumulative speed of the port-channel member ports.
PAGE 1046
revision The revision number for the multiple spanning tree configuration. Syntax revision range To return to the default values, use the no revision command. Parameters Defaults range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1047
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1048
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Enable the multiple spanning tree protocol prior to using this command.
PAGE 1049
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) loopback BPDU inconsistency causes.
PAGE 1050
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------------------------------------------------------Te 1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge Boundary ---------------------------------------------------------Te 1/1 ErrDis 128.257 128 20000 EDS 0 P2P No No DellEMC# show spanning-tree msti 0 MSTI 0 VLANs mapped 1-4094 Root Identifier has priority 32768, Address 0001.e801.
PAGE 1051
Defaults Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1052
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1053
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced By default, Dell EMC Networking OS implements an optimized flush mechanism for MSTP.
PAGE 1054
37 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1055
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 1056
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 1057
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile.
PAGE 1058
Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
PAGE 1059
-4 103.103.103.3 --> Source -----------------------------------------------------------------The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic. The mtrace command traverses the reverse path to the source from the destination.
PAGE 1060
-----------0 gi 1/10, 0 gi 1/10, 0 gi 1/11, 224.1.1.1 0.0.0.0 1000 1 gi 1/3, 224.1.1.2 0.0.0.0 1000 1 gi 1/3, 224.1.1.1 165.13.34.5 2000 2 gi 1/5, show ip mroute View the multicast routing table.
PAGE 1061
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 1062
Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 1063
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources.
PAGE 1064
ipv6 multicast-routing Enables IPv6 multicast forwarding. Syntax ipv6 multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable IP multicast forwarding on that VRF. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1065
9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1066
L2 Ports : L3 Ports : gi 1/10 show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1067
38 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1068
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1069
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. hardware_addres Enter a 48-bit hardware MAC address in nn:nn:nn:nn:nn:nn format. s Defaults None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1070
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1071
IPv6 Router Advertisement (RA) Guard The IPv6 RA guard provides support to perform conditional forwarding or blocking of the router advertisement messages that are received at the network device platform. This functionality analyzes and filters the RAs sent by the devices and compares the configuration information on the layer 2 device with the RA frame. Once the layer 2 device validates the content of the RA frame against the configuration, it forwards the RA to its unicast or multicast destination.
PAGE 1072
device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command. Parameters Defaults host Enter the keyword host to set the device-role as host. router Enter the keyword router to set the device-role as router. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 1073
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1074
ipv6 nd ra–guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1075
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters Defaults on Enter the keyword on to set the managed-config-flag value as ON.
PAGE 1076
Parameters ipv6–access-list name ipv6–prefix-list Defaults Enter the keywords ipv6–access-list then the access-list name. The accesslist name allows a maximum of 140 characters. name Enter the keywords ipv6–prefix-list then the prefix-list name. The prefix-list name allows a maximum of 140 characters. ipv6–macaccess-list name Enter the keywords ipv6–mac-access-list then the mac-access-list name. The mac-access-list name allows a maximum of 140 characters.
PAGE 1077
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1078
reachable–time Enable the verification of the configured reachability time in the received RA packets. Syntax reachable—time value To reset the advertised reachability time, use the no reachable-timevalue command. Parameters Defaults value Enter the advertised reachability time in milliseconds. The range is from 0 to 3,600,000 milliseconds. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 1079
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1080
router–preference maximum Enable the verification of the advertised default router preference (DRP) value. The preference value is lower than or equal to the specified limit. If this command is not configured, the verification process is bypassed. Syntax router-preference maximum {high | low | medium} To reset the default router preference value, use the no router-preference maximum {high | low | medium} command. Parameters Defaults high Enter the keyword high to set the DRP value as high.
PAGE 1081
Example Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1082
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Introduced on the S6000–ON, and Z9000 switches.
PAGE 1083
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1084
39 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1085
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface TenGigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1086
If the timer expires and an object’s state has changed, a notification is sent to the client. If no delay is configured, a notification is sent immediately after a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds. Related Commands ● track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface.
PAGE 1087
Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1088
show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object. Syntax show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500.
PAGE 1089
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP. DellEMC# show track Track 1 IP route 23.0.0.
PAGE 1090
To return to the default setting, use the no threshold metric {up number | down number} command. Parameters Defaults up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold. down number Enter a number for the DOWN threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default DOWN threshold is255.
PAGE 1091
track interface ip routing Configure object tracking on the routing status of an IPv4 Layer 3 interface. Syntax track object-id interface interface ip routing To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1092
To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1093
vrf vrf-name Defaults (Optional) You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1094
not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact IPv4 address and prefix length, the status of the tracked route is considered to be DOWN. When you configure the threshold of an IPv4 route metric as a tracked object, the UP/DOWN state of the tracked route is also determined by the current metric for the route in the routing table.
PAGE 1095
Usage Information Version Description 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv4 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8.
PAGE 1096
● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. track resolution ip route Configure the protocol-specific resolution value used to scale an IPv4 route metric. Syntax track resolution ip route {isis resolution-value | ospf resolution-value} To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500.
PAGE 1097
IPv6 Object Tracking Commands The following section describes the IPv6 object tracking commands. The following object tracking commands apply to IPv4 and IPv6: ● debug track ● delay ● description ● show running-config track ● threshold metric ● track interface line-protocol show track ipv6 route Display information about all tracked IPv6 routes, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1098
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP.
PAGE 1099
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a tunnel interface, enter the keyword tunnel.
PAGE 1100
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1101
ipv6-address/ prefix-len Defaults Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1102
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1103
40 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1104
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1105
Version Description 9.13(0.0) Introduced on the remaining DNOS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1106
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1107
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1108
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables.
PAGE 1109
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors.
PAGE 1110
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process.
PAGE 1111
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the database-timer rate-limit option for the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1112
Field Description ● MC+ (bit used by MOSPF is set and router is able to forward IP multicast packets) ● MC- (bit used by MOSPF is not set and router cannot forward IP multicast packets) ● E + (router is able to accept AS External LSAs) ● E - (router cannot accept AS External LSAs) ● T + (router can support TOS) ● T - (router cannot support TOS) Example hi: Displays the amount of time configured for the HELLO interval. di: Displays the amount of time configured for the DEAD interval.
PAGE 1113
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series.
PAGE 1114
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. description Add a description about the selected OSPF configuration. S4048–ON Syntax description description To remove the OSPF description, use the no description command.
PAGE 1115
Related Commands Version Description pre- 6.1.1.1 Introduced on the E-Series. ● show ip ospf asbr — display the VLAN configuration. distance Define an administrative distance for particular routes to a specific IP address. S4048–ON Syntax distance weight [ip-address mask access-list-name] To delete the settings, use the no distance weight [ip-address mask access-list-name] command. Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110.
PAGE 1116
distance ospf Configure an OSPF distance metric for different types of routes. S4048–ON Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255. The default is 110.
PAGE 1117
distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table. S4048–ON Syntax distribute-list prefix-list-name in [interface] To delete a filter, use the no distribute-list prefix-list-name in [interface] command. Parameters Defaults prefix-list-name Enter the name of a configured prefix list.
PAGE 1118
distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. S4048–ON Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters Defaults prefix-list-name Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed.
PAGE 1119
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and inter-area routes.
PAGE 1120
Generally, convergence level 1 meets most convergence requirements. Higher convergence levels should only be selected following consultation with Dell EMC Networking technical support. graceful-restart grace-period Specifies the time duration, in seconds, that the router’s neighbors continue to advertise the router as fully adjacent regardless of the synchronization state during a graceful restart.
PAGE 1121
graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart. S4048–ON Syntax graceful-restart helper-reject ip-address To return to default value, use the no graceful-restart helper-reject command. Parameters Defaults ip-address Enter the OSPF router-id, in IP address format, of the restart router that will not act as a helper during graceful restart. Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1122
Parameters Defaults planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only. Support for both planned and unplanned failures. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1123
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF.
PAGE 1124
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface.
PAGE 1125
Usage Information Version Description pre- 6.1.1.1 Introduced on the E-Series. All neighboring routers in the same network must use the same password to exchange OSPF information. ip ospf cost Change the cost associated with the OSPF traffic on an interface. S4048–ON Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters Defaults cost Enter a number as the cost. The range is from 1 to 65535. The default cost is based on the reference bandwidth.
PAGE 1126
ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. S4048–ON Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters Defaults seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds.
PAGE 1127
ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. S4048–ON Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters Defaults seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds. 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1128
To delete a key, use the no ip ospf message-digest-key keyid command. Parameters Defaults keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. No MD5 authentication is configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1129
ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets. S4048–ON Syntax ip ospf mtu-ignore To return to the default, use the no ip ospf mtu-ignore command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1130
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1131
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1132
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Set the time interval to a number large enough to prevent unnecessary retransmissions. ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed.
PAGE 1133
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. S4048–ON Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1134
maximum-paths Enable the software to forward packets over multiple paths. S4048–ON Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths.
PAGE 1135
To disable an OSPF area, use the no network ip-address mask area area-id command. Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format. (/x) area-id Enter the OSPF area ID as either a decimal value or in a valid IP address. Decimal value range is from 0 to 65535. IP address format is dotted decimal format A.B.C.D.
PAGE 1136
passive-interface Suppress both receiving and sending routing updates on an interface. S4048–ON Syntax passive-interface {default | interface} To enable both the receiving and sending routing, use the no passive-interface interface command. To return all OSPF interfaces (current and future) to active, use the no passive-interface default command. Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive.
PAGE 1137
The default keyword sets all interfaces as passive. You can then configure individual interfaces, where adjacencies are desired, using the no passive-interface interface command. The no form of this command is inserted into the configuration for individual interfaces when the no passiveinterface interface command is issued while passive-interface default is configured.
PAGE 1138
route-map map- name tag tag-value Defaults (OPTIONAL) Enter the keywords route-map then the name of the route map. (OPTIONAL) Enter the keyword tag then a number. The range is from 0 to 4294967295. Not configured. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1139
metric-type type-value (OPTIONAL) Enter the keywords metric-type then one of the following: ● 1 = for OSPF External type 1 ● 2 = for OSPF External type 2 route-map map- (OPTIONAL) Enter the keywords route-map then the name of the route map. name tag tag-value Defaults (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. None Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1140
level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
PAGE 1141
Parameters Defaults ip-address Enter the router ID in the IP address format. None. Command Modes ROUTER OSPF Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1142
Parameters Defaults process-id Enter a number for the OSPF instance. The range is from 1 to 65535. vrf name (Optional) Enter the VRF process identifier to tie the OSPF instance to the VRF. All network commands under this OSPF instance are then tied to the VRF instance. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1143
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1144
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.
PAGE 1145
show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. S4048–ON Syntax Parameters Defaults show ip ospf [process-id | vrf vrf-name] asbr process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1146
3.3.3.3 1.1.1.1 DellEMC# -/-/-/ E/-/-/ 2 0 10.0.0.2 0.0.0.0 Te 1/1 - 1 0 show ip ospf database Display all LSA information. If you do not enable OSPF on the switch, no output is generated. S4048–ON Syntax show ip ospf process-id [vrf vrf-name] database [database-summary] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1147
Example Field Description Link ID Identifies the router ID. ADV Router Identifies the advertising router’s ID. Age Displays the link state age. Seq# Identifies the link state sequence number. This number allows you to identify old or duplicate link state advertisements. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. DellEMC> show ip ospf 1 database OSPF Router with ID (11.1.2.
PAGE 1148
● the default destination (0.0.0.0) for Type 5 LSAs adv-router ip- address (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1148 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1149
Example Field Description Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. DellEMC# show ip ospf 100 database asbr-summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Asbr (Area 0.0.0.0) LS age: 1437 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.
PAGE 1150
● EXEC Privilege Command History Usage Information 1150 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1151
Example Field Description TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router. External Route Tag Displays the 32-bit field attached to each external route.
PAGE 1152
● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1152 This guide is platform-specific.
PAGE 1153
Example Field Description Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Length Displays the Fletcher checksum of an LSA’s complete contents. Network Mask Displays the length in bytes of the LSA. Attached Router Identifies the IP address of routers attached to the network. DellEMC# show ip ospf 1 data network OSPF Router with ID (20.20.20.5) (Process ID 1) Network (Area 0.0.0.
PAGE 1154
● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1155
● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1156
Example Item Description Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Opaque Type Displays the Opaque type field (the first 8 bits of the Link State ID). Opaque ID Displays the Opaque type-specific ID (the remaining 24 bits of the Link State ID). DellEMC> show ip ospf 1 database opaque-area OSPF Router with ID (3.3.3.
PAGE 1157
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1158
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1159
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added supported for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.20 Introduced on the S6000. 8.3.19.
PAGE 1160
Example Item Description (Link Data) Identifies the router interface address. Number of TOS Metric Lists the number of TOS metrics. TOS 0 Metric Lists the number of TOS 0 metrics. DellEMC# show ip ospf 100 database router OSPF Router with ID (1.1.1.10) (Process ID 100) Router (Area 0) LS age: 967 Options: (No TOS-capability, No DC, E) LS type: Router Link State ID: 1.1.1.10 Advertising Router: 1.1.1.
PAGE 1161
show ip ospf database summary Display the network summary (type 3) LSA routing information. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database summary [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1162
Example Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: ● TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service. ● DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. ● E or No E is displayed on whether the originating router can accept AS External LSAs.
PAGE 1163
DellEMC# Related Commands ● show ip ospf database — display OSPF database information. show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated. Syntax Parameters show ip ospf [process-id | vrf vrf-name] interface [interface] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1164
Usage Information Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id interface command shown in the following example. Item Description GigabitEthernet.. This line identifies the interface type slot/port and the status of the OSPF protocol . on that interface. Internet Address...
PAGE 1165
Process ID 1, Router ID 192.168.253.2, Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host. DellEMC> show ip ospf neighbor Display the OSPF neighbors connected to the local router. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] neighbor process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1166
Example Item Description Dead Time Displays the expected time until the Dell OS declares the neighbor dead. Address Displays the IP address of the neighbor. Interface Displays the interface type slot/port information. Area Displays the neighbor’s area (process ID). DellEMC# show ip ospf 34 neighbor Neighbor ID 20.20.20.7 192.10.10.2 20.20.20.1 DellEMC# Pri State Dead Time Address 1 FULL/DR 00:00:32 182.10.10.3 1 FULL/DR 00:00:37 192.10.10.2 1 FULL/DROTHER00:00:36 192.10.10.
PAGE 1167
Usage Information Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. This command is useful in isolating routing problems between the OSPF and the RTM. For example, if a route is missing from the RTM/FIB but is visible from the display output of this command, the problem is with downloading the route to the RTM.
PAGE 1168
neighbor routerid Defaults (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.). None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1168 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1169
Row Heading Description Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets. Other-Q The queue, for transmission or reception, for the link state acknowledgement, database description, and update packets. The following describes the error definitions for the show ip ospf statistics process-id global command.
PAGE 1170
Socket Errors DellEMC# Usage Information Example (Statistics) 0 The show ip ospf process-id statistics command displays the error packet count received on each interface as: ● The hello-timer remaining value for each interface ● The wait-timer remaining value for each interface ● The grace-timer remaining value for each interface ● The packet count received and transmitted for each neighbor ● Dead timer remaining value for each neighbor ● Transmit timer remaining value for each neighbor ● The LSU Q lengt
PAGE 1171
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 1172
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 1173
Usage Information Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.
PAGE 1174
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1175
● max-interval: 5000 msec Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1176
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. OSPFv3 Commands Open shortest path first version 3 (OSPFv3) for IPv6 is supported on the S4048–ON platform.
PAGE 1177
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 1178
key Text string used in encryption. The required lengths of a non-encrypted or encrypted key are: 3DES - 48 or 96 hex digits; DES - 16 or 32 hex digits; AES-CBC -32 or 64 hex digits for AES-128 and 48 or 96 hex digits for AES-192. authenticationalgorithm key-encryptiontype key Specifies the authentication algorithm to use for encryption. Valid values are MD5 or SHA1. (OPTIONAL) Specifies if the authentication key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted).
PAGE 1179
To remove an IPsec encryption policy from an interface, enter the no area area-id encryption spi number command. Related Commands ● ipv6 ospf encryption – configure an IPsec encryption policy on an OSPFv3 interface. ● show crypto ipsec policy – display the configuration of IPsec encryption policies. area nssa Specify an area as a not so stubby area (NSSA). Syntax area area-id nssa [default-information-originate] [no-redistribution] [nosummary] To delete an NSSA, use the no area area-id nssa command.
PAGE 1180
auto-cost Specify how the OSPF interface cost is calculated based on the reference bandwidth method. S4048–ON Syntax auto-cost [reference-bandwidth ref-bw] To return to the default bandwidth or to assign cost based on the interface type, use the no autocost [reference-bandwidth ref-bw] command. Parameters Defaults ref-bw (OPTIONAL) Specify a reference bandwidth in megabits per second. The range is from 1 to 4294967. The default is 100 megabits per second. 100 megabits per second.
PAGE 1181
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.
PAGE 1182
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the S4820T, S4810, and Z9000. The following section describes the command fields. Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1183
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. vrf vrf-name Enter the keyword vrf to view debugging information on OSPF corresponding to that VRF. Command Modes EXEC Privilege Command History Example Example (detail) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1184
Command Fields Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version.. type: Displays the type of packet sent: ● 1 - Hello packet ● 2 - database description ● 3 - link state request ● 4 - link state update ● 5 - link state acknowledgement Length: Displays the OSPFv3 packet length. Router ID: Displays the OSPFv3 router ID. Area ID: Displays the OSPFv3 area ID.
PAGE 1185
Example Example (detail) Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on E-Series.
PAGE 1186
Lines Beginning With or Including Description Chksum: Displays the OSPFv3 checksum. debug ipv6 ospf spf Display debug information for SPF timers on OSPF IPv6 packets. Syntax [no] debug ipv6 ospf spf [vrf vrf-name] Parameters interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1187
00:59:27 : OSPFv3INFO: OSPFV3 Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 Interface Te 1/2 IfIndex 34145282 00:59:27 : OSPFv3INFO: BFD parameters interval 100 min_rx 100 mult 3 role active 00:59:27 : OSPFv3INFO: BFD parameters interval 100 min_rx 100 mult 3 role active 00:59:27 : OSPFv3INFO: Completed Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 Aug 25 11:19:59: %STKUNIT0-M:CP %BFDMGR-1-BFD_STATE_CHANGE: Changed session state to Init for neighbor fe80::201:e8ff:fe8b:7720
PAGE 1188
Related Commands Version Description 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. ● redistribute — redistribute routes from other routing protocols into OSPFv3. graceful-restart grace-period Enable OSPFv3 graceful restart globally by setting the grace period (in seconds) that an OSPFv3 router’s neighbors continues to advertise the router as adjacent during a graceful restart.
PAGE 1189
graceful-restart mode Specify the type of events that trigger an OSPFv3 graceful restart. Syntax graceful-restart mode {planned-only | unplanned-only} To disable graceful restart mode, enter no graceful-restart mode. Parameters Defaults planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only.
PAGE 1190
Parameters Defaults process-id Enter the process identification number. area area-id Specify the OSPF area. The range is from 0 to 4294967295. None Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.2) Increased the area ID value from 65535 to 4294967295. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1191
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1192
The default is Active. Defaults See Parameters. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.
PAGE 1193
Usage Information Version Description 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1194
ipv6 ospf encryption Configure an IPsec encryption policy for OSPFv3 packets on an IPv6 interface. Syntax ipv6 ospf encryption {null | ipsec spi number esp encryption-algorithm [key-encryption-type] key athentication-algorithm [key-encryption-type] key}} Parameters null Causes an encryption policy configured for the area to not be inherited on the interface. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1195
Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Before you enable IPsec encryption on an OSPFv3 interface, first enable IPv6 unicast routing globally, configure an IPv6 address and enable OSPFv3 on the interface, and assign the interface to an area. An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router.
PAGE 1196
ipv6 ospf hello-interval Specify the time interval between the hello packets sent on the interface. Syntax ipv6 ospf hello—interval seconds To return to the default time interval, enter no ipv6 ospf hello—interval. Parameters Defaults seconds Enter the time interval in seconds as the time between hello packets. The range is from 1 to 65525 seconds. 10 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1197
Version Description 9.14(2.3) Introduced on the C9000, S3048-ON, S3100, S4048-ON, S4048T-ON, S6000, and Z9100-ON. ipv6 ospf priority To determine the Designated Router for the OSPFv3 network, set the priority of the interface. Syntax ipv6 ospf priority number To return to the default time interval, use the no ipv6 ospf priority command. Parameters Defaults number Enter the number as the priority. The range is from 1 to 255.
PAGE 1198
Parameters Defaults process-id Enter the process identification number. The range is from 1 to 65535. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF. None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1199
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. passive-interface Disable (suppress) sending routing updates on an interface.
PAGE 1200
Usage Information Version Description 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. By default, no interfaces are passive. Routing updates are sent to all interfaces on which the routing protocol is enabled.
PAGE 1201
Defaults Not configured. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON.
PAGE 1202
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. You can configure an arbitrary value in the IP address for each router. However, each router ID must be unique.
PAGE 1203
Related Commands Example show crypto ipsec sa ipv6– displays the IPsec security associations used on OSPFv3 interfaces.
PAGE 1204
show crypto ipsec sa ipv6 Display the IPsec security associations (SAs) used on OSPFv3 interfaces. Syntax show crypto ipsec sa ipv6 [interface interface] Parameters interface interface (OPTIONAL) Displays information about the SAs used on a specified OSPFv3 interface, where interface is one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1205
in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound ah sas spi : 500 (0x1f4) transform : ah-md5-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE inbound esp sas outbound esp sas Interface: TenGigabitEthernet 1/2 Link Local address: fe80::201:e8ff:fe40:4d11 IPSecv6 policy name: OSPFv3-1-600 inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection suppor
PAGE 1206
show ipv6 ospf database Display information in the OSPFv3 database, including link-state advertisements (LSAs) in detail. Syntax show ipv6 ospf [process-number] [vrf vrf-name] database [database-summary | grace-lsa | external | inter-area-prefix | inter-area-router | intra-areaprefix | link | network | router | nssa-external] Parameters process-number Enter the OSPF process number.
PAGE 1207
Usage Information Example (gracelsa) Version Description 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.4.2.2 Added support for the display of graceful restart parameters and Type-11 Grace LSAs on E-Series routers. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series.
PAGE 1208
Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 E1200-T2C2#sh ipv6 ospf neighbor Neighbor ID Interface 63.114.8.36 Example (external) Pri 1 State FULL/DR Dead Time 00:00:37 Interface ID 4 Te 1/4 DellEMC# show ipv6 ospf database external OSPFv3 Router with ID (10.160.3.
PAGE 1209
interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1210
show ipv6 ospf neighbor Display the OSPF neighbor information on a per-interface basis. Syntax show ipv6 ospf [process-number] [vrf vrf-name] neighbor [interface] Parameters process-number Enter the OSPF process number. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display OSPF neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
PAGE 1211
timers spf Set the time interval between when the switch receives a topology change and starts a shortest path first (SPF) calculation. S4048–ON Syntax timers spf delay holdtime msec To return to the default, use the no timers spf command. Parameters Defaults delay Enter a number as the delay. The range is from 0 to 2147483647. The default is 5 seconds. When configured in milli seconds, 100 is the least value that is allowed to be configured. holdtime Enter a number as the hold time.
PAGE 1212
41 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1213
Related Commands Version Description 7.7.1.0 Introduced on the E-Series. ● ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name test [l2–switch] To remove a redirect list from an interface, use the no ip redirect-group name command.
PAGE 1214
The Layer2 PBR option matches the layer2 traffic flow. If you un-configure this option, then the Layer2 traffic is not matched. You can apply the l2–switch option to redirect Layer2 traffic only on a VLAN interface. This VLAN interface must be configured with an IP address for ARP resolution. NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces. The Layer3 routing is not affected on the same interface on which Layer2 PBR is applied.
PAGE 1215
permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: ● If you know the filter sequence number, use the no seq sequence-number syntax command.
PAGE 1216
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1217
● rst = reset the connection ● syn = synchronize sequence number ● urg = urgent field Defaults source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1218
[bit] [operator]{source-port source-port| source-port-range start-port end-port} {destination-port destination-port| destination-port-range startport - end-port} To delete a filter, use the no seq sequence-number command. Parameters 1218 sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the keyword IP address of the forwarding router.
PAGE 1219
destination-port- Enter the keywords destination-port-range then the range of the start port range to end port to be matched in the ACL rule in the ICAP rule. Defaults none Command Modes REDIRECT-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1220
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The show cam pbr command displays the PBR CAM content.
PAGE 1221
seq 15 redirect tunnel 2 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Next-hop reachable (via Te 1/32) seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.0/24, Track 5 [up], Next-hop reachable (via Po 5) seq 30 redirect 155.1.1.2 track 6 icmp host 8.8.8.8 any, Track 5 [up], Next-hop reachable (via Po 5) seq 35 redirect 42.1.1.2 icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20) seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30) seq 45 redirect 31.1.1.
PAGE 1222
42 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
PAGE 1223
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1224
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
PAGE 1225
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled.
PAGE 1226
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1227
ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1228
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Removed the in and out parameters. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 1229
Example Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced DellEMC(conf)# ip access-list standard map1 DellEMC(config-std-nacl)# permit 224.0.0.
PAGE 1230
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command.
PAGE 1231
To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. access-list Defaults Enter the name of an extended access list. Maximum 16 characters. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1232
group-address group-address mask override Enter the keywords group-address then a group-address mask, in dotted decimal format (/xx), to assign that group address to the RP. Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable. NOTE: This option is applicable to multicast group range. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1233
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
PAGE 1234
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1235
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Removed the acl-access-list parameter. Modified the max value of S, G entry second range from 86400 to 65535. Introduced on the S6000ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1236
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.7(0.0) Added support for VRF. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 1237
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1238
If the PIM DR flood is not disabled (default setting): ● Multicast traffic is transmitted on the egress port towards the PIM DR if the port is not the incoming interface. ● Multicast traffic for an unknown group is sent on the port towards the PIM DR. When DR flooding is disabled, multicast traffic for an unknown group is dropped. show ip pim bsr-router View information on the Bootstrap router.
PAGE 1239
show ip pim interface View information on the interfaces with IP PIM enabled. S4048–ON Syntax Parameters show ip pim [vrf vrf-name] interface vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on this VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1240
Field Description DR Displays the IP address of the Designated Router for that interface. The show ip pim interface command does not display information corresponding to the loop-back interfaces. Example DellEMC# show ip pim interface Address Interface Ver/ Mode 165.87.34.5 Te 1/10 v2/S 10.1.1.2 Vl 10 v2/S 20.1.1.5 Vl 20 v2/S 165.87.31.200 Vl 30 v2/S DellEMC# Nbr Count 0 1 1 1 Query Intvl 30 30 30 30 DR Prio 1 1 1 1 DR 165.87.34.5 10.1.1.2 20.1.1.5 165.87.31.
PAGE 1241
Usage Information The following describes the show ip pim neighbor command shown in the following example. Field Description Neighbor address Displays the IP address of the PIM neighbor. Example Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found.
PAGE 1242
Example Example (Mapping) Example (Address) Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. DellEMC# show ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.
PAGE 1243
Usage Information Example (#2) Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series. The following describes the show ip pim snooping interface commands shown in the following example. Field Description Interface Displays the VLAN interfaces with PIM-SM snooping enabled.
PAGE 1244
Field Description Neighbor address Displays the IP address of the neighbor learned through PIM-SM snooping. Example Interface Displays the VLAN ID number and slot/port on which the PIM-SM-enabled neighbor was discovered. Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires).
PAGE 1245
Usage Information Example The following describes the show ip pim snooping tib commands shown in the following example. Field Description (S, G) Displays the entry in the PIM multicast snooping database. uptime Displays the amount of time the entry has been in the PIM multicast route table. expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1246
show ip pim ssm-range Display the non-default groups added using the SSM range feature. 4048–ON Syntax show ip pim [vrf vrf-name] ssm-range Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1247
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1248
0/0 0/0 0/0 0/0 State-Refresh messages sent/received MSDP updates sent/received Null Register messages sent/received Register-stop messages sent/received Data path event summary: 0 no-cache messages received 0 last-hop switchover messages received 0/0 pim-assert messages sent/received 0/0 register messages sent/received DellEMC# show ip pim tib View the PIM tree information base (TIB).
PAGE 1249
Example Field Description (S, G) Displays the entry in the multicast PIM database. uptime Displays the amount of time the entry has been in the PIM route table. expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1250
show running-config pim Display the current configuration of PIM-SM. Syntax show running-config pim Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.
PAGE 1251
Command History Related Commands Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. show ipv6 pim tib – displays the IPv6 PIM tree information base (TIB) debug ipv6 pim Invoke IPv6 PIM debugging.
PAGE 1252
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 9.14(1.0) Usage Information Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON. This command is applied to the subsequent PIM-BSR. Existing BSR advertisements are cleaned up by time-out.
PAGE 1253
Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.11.3.
PAGE 1254
NOTE: The :: notation specifies successive hexadecimal fields of zero. group-address group-address mask override Enter the keywords group-address then the group address in the x:x:x:x::x format and then the mask in /nn format to assign that group address to the RP. NOTE: The :: notation specifies successive hexadecimal fields of zero. (OPTIONAL) Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable.
PAGE 1255
NOTE: If you do not specify the acl-name, the system uses the default multicast IPv6 group range, which is ff00::/8. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON.
PAGE 1256
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL.
PAGE 1257
Example Version Description 9.14(1.0) Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON.
PAGE 1258
]Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. detail (OPTIONAL) Enter the keyword detail to displayed PIM neighbor detailed information. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 1259
DellEMC#show run pim ! ip pim bsr-candidate Loopback 0 ip pim vrf red bsr-candidate Loopback 1 ip pim vrf blue bsr-candidate Loopback 2 ip pim vrf red rp-candidate Loopback 1 ip pim vrf blue rp-candidate Loopback 2 ipv6 pim bsr-candidate Loopback 0 ipv6 pim vrf red bsr-candidate Loopback 1 ipv6 pim vrf blue bsr-candidate Loopback 2 ipv6 pim rp-candidate Loopback 0 100 def_vrf_acl ipv6 pim vrf red rp-candidate Loopback 1 100 def_vrf_acl ipv6 pim vrf blue rp-candidate Loopback 2 60 blue_vrf_acl_dut DellEMC# E
PAGE 1260
Example Dell# show ipv6 pim summary PIM TIB version 1480 Uptime 5d4h Entries in PIM-TIB/MFC : 105/81 Active Modes : PIM-SM Interface 3 0 2 summary: active PIM interfaces passive PIM interfaces active PIM neighbors TIB summary: 12/12 (*,G) entries in PIM-TIB/MFC 69/69 (S,G) entries in PIM-TIB/MFC 24/0 (S,G,Rpt) entries in PIM-TIB/MFC 8 PIM nexthops 1 RPs 7 sources 30 Register states Message summary: 47132/53793 Joins/Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/
PAGE 1261
Example Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010.
PAGE 1262
43 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1263
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1264
monitor multicast-queue Configure monitor QoS multicast queue ID. Syntax monitor multicast-queue queue-id To remove the configuration, use the no monitor multicast-queue command. Parameters Defaults queue-id Enter the QoS multicast queue ID. The range is from 0 to 9. queue-id: 0 Enable status: Disabled Command Modes CONFIGURATION Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific.
PAGE 1265
Defaults set ip dscp Configures the Differentiated Services Code Point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default value, use the no form of this command. dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic.
PAGE 1266
rate-limit Configure the rate-limit to limit the mirrored packets. Syntax rate-limit limit To remove the limit, use the no rate-limit limit command. Parameters Defaults limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. 60 Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1267
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1268
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1269
● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1270
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. ● For a port channel interface, enter the keywords port-channel then a number. range Enter the keyword range to specify the list of interfaces. any Enter the keyword any to specify all interfaces. NOTE: This option is applicable only with drop monitor session.
PAGE 1271
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1272
44 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1273
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. S4048 Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1274
private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. S4048 Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN.
PAGE 1275
private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input.
PAGE 1276
To remove PVLAN mode from the selected port, use the no switchport mode private-vlan command. Parameters Defaults host Enter the keyword host to configure the selected port or port channel as an isolated interface in a PVLAN. promiscuous Enter the keyword promiscuous to configure the selected port or port channel as an promiscuous interface. trunk Enter the keyword trunk to configure the selected port or port channel as a trunk port in a PVLAN. Disabled.
PAGE 1277
45 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the S4048 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1278
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S4048 Syntax disable To enable PVST+, use the no disable command.
PAGE 1279
Related Commands ● protocol spanning-tree pvst — enter PVST+ mode. extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S4048 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
PAGE 1280
-------------------------------------------------------Te 1/10 Desg 128.140 128 200000 FWD 0 P2P No Te 1/12 Dis 128.142 128 200000 DIS 0 P2P No DellEMC(conf-pvst)# Related Commands ● protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command.
PAGE 1281
Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands ● disable — disables PVST+. ● show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. S4048 Syntax Parameters Defaults show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094.
PAGE 1282
Usage Information Example (Brief) Version Description 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples.
PAGE 1283
Port 131 (TenGigabitEthernet 1/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.131 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1284
Related Commands ● spanning-tree pvst — configure PVST+ on an interface. spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
PAGE 1285
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
PAGE 1286
no ip address switchport spanning-tree pvst vlan 3 cost 1800 no shutdown DellEMC(conf-if-te-1/1)# end DellEMC# Related Commands ● show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN.
PAGE 1287
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. S4048 Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1288
bridge-priority value Defaults Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. 32768 Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1289
Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1290
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1291
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1292
46 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1293
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis.
PAGE 1294
When you set the priority for a port channel, the physical interfaces assigned to the port channel are configured with the same value. You cannot assign the dot1p-priority command to individual interfaces in a port channel. rate police Police the incoming traffic rate on the selected interface. Syntax rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] [vlan vlan-id] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1295
S-Series On one interface, you can configure the rate police command for a VLAN or you can configure the rate police command for an interface. rate-shape Shape the traffic output on the selected interface. Syntax Parameters Defaults rate shape [kbps] rate [burst-KB] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
PAGE 1296
Related Commands ● rate-shape — shapes traffic output as part of the designated policy. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. S4048–ON Syntax service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} Parameters Defaults queue Enter a value from 0 to 7.
PAGE 1297
To return to the default setting, use the no service-class dynamic dot1p command. Defaults All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command. The default mapping is as follows: dot1p Queue ID 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 Command Modes ● INTERFACE ● CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1298
● All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally. ● Layer 2 or Layer 3 service policies supersede dot1p service classes. strict-priority unicast Configure a unicast queue as a strict-priority (SP) queue. Syntax strict-priority unicast number Parameters Defaults unicast number Enter the keyword unicast then the queue number. The range is from 1 to 3.
PAGE 1299
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify data traffic into one of eight classes . Dell EMC Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
PAGE 1300
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-of-service policies to each class. Syntax class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] Parameters Defaults match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
PAGE 1301
Related Commands ● ● ● ● ● ● ● ● ● ● ip access-list extended — configures an extended IP ACL. ip access-list standard — configures a standard IP ACL. match ip access-group — configures the match criteria based on the access control list (ACL). match ip precedence — identifies the IP precedence values as match criteria. match ip dscp — configures the match criteria based on the DSCP value. match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL.
PAGE 1302
Related Commands Version Description 6.1.1.1 Introduced on the E-Series. ● show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the policies (80 characters maximum).
PAGE 1303
match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IP-any class-maps on both ACLs as well as VLANs.
PAGE 1304
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed. Related Commands ● class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria.
PAGE 1305
Usage Information Version Description 7.7.1.0 Added the keyword multicast ; added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series; added support for the DSCP Marking option. 6.2.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive.
PAGE 1306
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1307
Usage Information Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. To access this command, enter the class-map command.
PAGE 1308
match mac access-group Configure a match criterion for a class map, based on the contents of the designated MAC ACL. Syntax [seq sequence number] match mac access-group {mac-acl-name} Parameters Defaults mac-acl-name Enter a MAC ACL name. Its contents is used as the match criteria in the class map. none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1309
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1310
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced.
PAGE 1311
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information An aggregate output QoS policy applies to all outbound port traffic.
PAGE 1312
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series.
PAGE 1313
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map.
PAGE 1314
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined. This command enables the qos-policy-input configuration mode— (conf-qos-policy-in).
PAGE 1315
Version Description 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rateshape, scheduler strict, bandwidth-percentage, and WRED can be defined. This command enables the qos-policy-output configuration mode—(conf-qos-policy-out).
PAGE 1316
Important Points to Remember — Multicast-Bandwidth Option ● A unique multicast weighted fair queuing (WFQ) setting can be applied only on a per port-pipe basis. The minimum percentage of the multicast bandwidth assigned to any of the ports in the port-pipe takes effect for the entire port-pipe. ● If the percentage of multicast bandwidth is 0, control traffic going through multicast queues are dropped.
PAGE 1317
NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast. rate-police Specify the policing functionality on incoming traffic. Syntax Parameters Defaults rate-police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1318
Related Commands ● rate police — specifies traffic policing on the selected interface. ● qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy. Syntax rate-shape [kbps | pps] peak-rate [burst-kbps | burst-packets] commited [kbps | pps] commited-rate [burst-kbps | burst-packets] Parameters Defaults pps Enter the keyword pps to specify the rate limit in packets per second (pps).
PAGE 1319
propagates at an average rate that is less than or equal to the committed rate, it is considered to be green-colored or coded. When the transmitted traffic falls below the committed rate, the bandwidth, which is not used by any traffic that is traversing the network, is aggregated to form the committed burst size. Traffic is considered to be green-colored up to the point at which the unused bandwidth does not exceed the committed burst size.
PAGE 1320
Usage Information You can attach a single policy-map to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. NOTE: The service-policy commands are not allowed on a port channel. The servicepolicy input policy-map-name command and the service-class dynamic dot1p command are not allowed simultaneously on an interface.
PAGE 1321
Related Commands ● policy-map-output — creates an output policy map. service-queue Assign a class map and QoS policy to different queues. S4048–ON Syntax service-queue queue-id [class-map class-map-name] [qos-policy qos-policyname] To remove the queue assignment, use the no service-queue queue-id [class-map classmap-name] [qos-policy qos-policy-name] command. Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7.
PAGE 1322
Related Commands ● class-map — identifies the class map. ● service-policy input — applies an input policy map to the selected interface. ● service-policy output — applies an output policy map to the selected interface. set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. S4048–ON Syntax set {ip-dscp value | mac-dot1p value} Parameters Defaults ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63.
PAGE 1323
show qos class-map View the current class map information. Syntax Parameters Defaults show qos class-map [class-name] class-name (Optional) Enter the name of a configured class map. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option on all the Dell EMC Networking OS platforms.
PAGE 1324
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1325
Command History Example (IPv4) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1326
show qos policy-map-input View the input QoS policy map details. S4048–ON Syntax show qos policy-map-input [policy-map-name] [class class-map-name] [qospolicy-input qos-policy-name] Parameters policy-map-name Enter the policy map name. class class-map- name qos-policy-input qos-policy-name Defaults Enter the keyword class then the class map name. Enter the keyword qos-policy-input then the QoS policy name.
PAGE 1327
Example DellEMC# show qos policy-map-input Policy-map-input pmap1 Trust ipv6-diffserv Queue# Class-map-name 0 c0 1 c1 2 c2 3 c3 4 c4 5 c5 6 c6 7 c7 DellEMC# Qos-policy-name q0 q1 q2 q3 q4 q6 q7 show qos policy-map-output View the output QoS policy map details. S4048–ON Syntax Parameters show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] policy-map-name Enter the policy map name. qos-policyoutput qos- Enter the keyword qos-policy-output then the QoS policy name.
PAGE 1328
Example Version Description 6.1.1.1 Introduced on the E-Series. DellEMC# show qos policy-map-output Policy-map-output PolicyMapOutput Aggregate Qos-policy-name AggPolicyOut Queue# Qos-policy-name 0 qosPolicyOutput DellEMC# show qos qos-policy-input View the input QoS policy details. S4048–ON Syntax show qos qos-policy-input [qos-policy-name] Parameters Defaults qos-policy-name Enter the QoS policy name.
PAGE 1329
DellEMC# Rate-police 100 50 peak 100 50 Dscp 32 show qos qos-policy-output View the output QoS policy details. S4048–ON Syntax Parameters Defaults show qos qos-policy-output [qos-policy-name] qos-policy-name Enter the QoS policy name. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1330
show qos statistics View QoS statistics. Syntax show qos statistics {egress—queue [interface]} | {wred-profile [interface]} | [interface] Parameters egress-queue interface wred-profile interface interface Defaults Enter the keyword egress-queue to display the egress-queue statistics and optionally one of the following keywords and slot/port or number information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1331
Version Description 7.7.1.1 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1332
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series.
PAGE 1333
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1334
0 1 Exception 1 0 Allowed (5) 1 1 Exception 13 (2) DellEMC# L2ACL 100 200 L2ACL 1000 200 L2ACL 0 200 … … … L2ACL 1 400 200 Allowed threshold Specify the minimum and maximum threshold values for the configured WRED profiles. S4048–ON Syntax threshold min number max number max-drop-drop To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile.
PAGE 1335
Usage Information To configure the minimum and maximum threshold values for user-defined profiles, use this command. Additionally, to modify the minimum and maximum threshold values for the pre-defined WRED profiles, use this command. If you delete the threshold values of the pre-defined WRED profiles, the profiles revert to their original default values. Table 5.
PAGE 1336
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added fallback to the E-Series. 8.2.1.0 Added dot1p to the C-Series and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added dot1p and IPv6 DSCP . 6.1.1.1 Introduced on the E-Series. When you configure trust, matched bytes/packets counters are not incremented in the show qos statistics command.
PAGE 1337
profile-name Enter your WRED profile name in character format (32 character maximum). Or use one of the five pre-defined WRED profile names. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_. Defaults When WRED green is applied, default WRED yellow profiles take effect and vice-versa. Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific.
PAGE 1338
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1339
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1340
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1341
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information A color map outlines the codepoint mappings to the appropriate color mapping (green, yellow, red) for the traffic.
PAGE 1342
Version Description Version 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information If the specified color-map does not exist, the Diffserv Manager (DSM) creates a color map and sets all the DSCP values to green (low drop precedence). Example The following example assigns the color map, bat-enclave-map, to interface te 1/11.
PAGE 1343
Interface TE 1/10 dscp-color-map mapONE Displayed detailed color policy information on an interface. DellEMC# show qos dscp-color-policy detail te 1/10 Interface TenGigabitEthernet 1/10 Dscp-color-map mapONE yellow 4,7 red 20,30 Related Commands ● show qos dscp-color-map — displays DSCP color maps. show qos dscp-color-map Display the DSCP color map for one or all interfaces. Syntax Parameters Defaults show qos dscp-color-map map-name map-name Enter the name of the color map.
PAGE 1344
47 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1345
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1346
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. S4048–ON Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1347
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic.
PAGE 1348
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command.
PAGE 1349
Related Commands ● redistribute — allows you to redistribute routes learned by other methods. description Enter a description of the RIP routing protocol. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the RIP protocol (80 characters maximum). none Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1350
To return to the default values, use the no distance weight [ip-address mask] command. Parameters Defaults weight Enter a number from 1 to 255 for the weight (for prioritization). The default is 120. ip-address (OPTIONAL) Enter the IP address, in dotted decimal format (A.B.C.D), of the host or network to receive the new distance metric. mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x).
PAGE 1351
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1352
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults connected (OPTIONAL) Enter the keyword connected to filter only directly connected routes.
PAGE 1353
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. S4048–ON Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1354
2 Defaults (OPTIONAL) Enter the number 2 for RIP version 2. RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1355
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1356
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1357
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. S4048–ON Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command.
PAGE 1358
Usage Information Related Commands When a neighbor router is identified, unicast data exchanges occur. Multiple neighbor routers are possible. To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. ● passive-interface — sets the interface to only listen to RIP broadcasts. network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command.
PAGE 1359
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. S4048–ON Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters Defaults prefix-list-name Enter the name of an established Prefix list to determine which incoming routes are modified.
PAGE 1360
Related Commands ● ip prefix-list — enters PREFIX-LIST mode and configure a prefix list. output-delay Set the interpacket delay of successive packets to the same neighbor. S4048–ON Syntax output-delay delay To return to the switch software defaults for interpacket delay, use the no output-delay command. Parameters Defaults delay Specify a number of milliseconds as the delay interval. The range is from 8 to 50. Not configured.
PAGE 1361
passive-interface Suppress routing updates on a specified interface. S4048–ON Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. Parameters Defaults interface Enter the following information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1362
redistribute Redistribute information from other routing instances. Syntax redistribute {connected | static} To disable redistribution, use the no redistribute {connected | static} command. Parameters Defaults connected Enter the keyword connected to specify that information from active routes on interfaces is redistributed. static Enter the keyword static to specify that information from static routes is redistributed. Not configured.
PAGE 1363
Parameters tag (OPTIONAL) Enter the name of the IS-IS routing process. level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16.
PAGE 1364
metric metric- value route-map map- name Defaults (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16. (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1365
Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1366
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. DellEMC(conf-router_rip)# show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1 DellEMC(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated.
PAGE 1367
Usage Information Example Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24...
PAGE 1368
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1369
flush Defaults ● ● ● ● Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table. The flush value should be greater than the update value. The range is from zero (0) to 4294967295. The default is 240 seconds.
PAGE 1370
Command Modes ROUTER RIP Command History Related Commands 1370 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1371
48 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1372
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1373
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1374
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1375
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
PAGE 1376
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1377
show rmon Display the RMON running status including the memory usage. S4048–ON Syntax show rmon Defaults none Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 1378
show rmon alarms Display the contents of the RMON alarm table. S4048–ON Syntax show rmon alarms [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) 1378 This guide is platform-specific.
PAGE 1379
-------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 6 1.3.6.1.2.1.1.3 7 1.3.6.1.2.1.1.3 8 1.3.6.1.2.1.1.3 9 1.3.6.1.2.1.1.3 10 1.3.6.1.2.1.1.3 11 1.3.6.1.2.1.1.3 12 1.3.6.1.2.1.1.3 13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table.
PAGE 1380
Example (Index) Example (Brief) 1380 Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf)# rmon event 111 -> DellEMC(conf)# rmon event 112 log -> DellEMC(conf)# rmon event 113 trap private -> DellEMC(conf)# rmon event 114 log trap public-> options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none.
PAGE 1381
21 21 22 22 DellEMC# show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. S4048–ON Syntax Parameters Defaults show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) This guide is platform-specific.
PAGE 1382
falling threshold: 300, RMON event index: 4 alarm sampling failed 0 times. alarm owner: alarm storage type: non-volatile. alarm status: OK DellEMC# Example (Brief) DellEMC# show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 DellEMC# show rmon history Display the contents of the RMON Ethernet history table.
PAGE 1383
Example (Index) Example (Brief) Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1384
Usage Information Example (Index) Example (Brief) Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The log table has a maximum of 500 entries.
PAGE 1385
Example (Index) Example (Brief) Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1386
6003 101236775 6004 101236775 9001 134529054 9002 134529054 9003 134791198 9004 134791198 DellEMC# 1386 Remote Monitoring (RMON) TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet 2/1 2/1 3/2 3/2 3/1 3/1
PAGE 1387
49 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1388
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1389
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# debug spanning-tree rstp bpdu tengigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree.
PAGE 1390
disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1391
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1392
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1393
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● forward-delay — changes the wait time before RSTP transitions to the Forwarding state. ● hello-time — changes the time interval between BPDUs.
PAGE 1394
Example Related Commands DellEMC(conf)# protocol spanning-tree rstp DellEMC(config-rstp)# no disable ● disable — disables RSTP globally on the system. show config View the current configuration for the mode. Only non-default values are displayed. Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1395
guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example (Brief) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1396
Te 4/1 128.419 128 20000 FWD 20000 16384 0001.e801.6aa8 128.419 Te 4/8 128.426 128 20000 FWD 20000 8192 0001.e805.e306 128.130 Te 4/9 128.427 128 20000 BLK 20000 8192 0001.e805.e306 128.131 Interface Name Role ----------Te 4/2 Desg Te 4/1 Desg Te 4/8 Root Te 4/9 Altr DellEMC# Example (EDS, LBK) PortID Prio Cost Sts Cost Link-type Edge ---- ------- --- ------- --------- ---128.418 128 20000 FWD 20000 P2P Yes 128.419 128 20000 FWD 20000 P2P Yes 128.426 128 20000 FWD 20000 P2P No 128.
PAGE 1397
Parameters cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1398
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the optional bridge port data unit (BPDU) guard. 6.2.1.1 Introduced on the E-Series. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1399
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.
PAGE 1400
50 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
PAGE 1401
51 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant.
PAGE 1402
Defaults dot1x Enter the keyword dot1x to send accounting information when a dot1x user has logged in. commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: ● For name, enter a user-defined name of a list of accounting methods.
PAGE 1403
Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
PAGE 1404
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. ● aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL.
PAGE 1405
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1406
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.
PAGE 1407
Defaults commands { level | role role-name } Enter the keyword commands followed by either a privilege level for accounting of commands executed at that privilege level, or enter the keyword role then the role name for authorization of commands executed by a user with that user role. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands. none Command Modes LINE Command History Related Commands This guide is platform-specific.
PAGE 1408
Defaults default Define the default list of authorization methods. local Use the authorization parameters on the system to perform authorization. tacacs+ Use the TACACS+ protocol to perform authorization. none Enter the keyword none to apply no authorization. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1409
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1410
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS.
PAGE 1411
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1412
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys.
PAGE 1413
If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command. Related Commands ● show running-config— Display the current configuration and display changes from the default values. ● service password-encryption— Encrypts all passwords configured in the system. Authentication and Password Commands To manage access to the system, use the following the commands.
PAGE 1414
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell EMC Networking OS uses the methods defined for Enable access instead.
PAGE 1415
... method4 Defaults (OPTIONAL) Enter up to four additional methods. In the event of a “no response” from the first method, the system applies the next configured method (up to four configured methods). Not configured (that is, no authentication is performed). Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1416
Related Commands ● ● ● ● login authentication — enables AAA login authentication on the terminal lines. password — creates a password. radius-server host — specifies a RADIUS server host. tacacs-server host — specifies a TACACS+ server host. aaa reauthenticate enable Enable re-authentication of user whenever there is a change in the authenticators. Syntax aaa reauthenticate enable To disable the re-authentication option, use the no aaa reauthenticate enable command.
PAGE 1417
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1418
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1419
Defaults No password is configured. level = 15. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1420
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Only Dell EMC Networking Technical Support staff use this command. enable secret Change the password for the enable command. Syntax enable secret [level level] [encryption-type] password To delete a password, use the no enable secret [encryption-type] password [level level] command.
PAGE 1421
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: ● Start with a letter, not a number. ● Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression.
PAGE 1422
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. If you configure the aaa authentication login default command, the login authentication default command automatically is applied to all terminal lines.
PAGE 1423
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1424
upper number (OPTIONAL) Enter the keyword upper then the upper number. The range is from 0 to 31. lower number (OPTIONAL) Enter the keyword lower then the lower number. The range is from 0 to 31. numeric number (OPTIONAL) Enter the keyword numeric then the numeric number. The range is from 0 to 31. special-char (OPTIONAL) Enter the keywords special-char then the number of special characters permitted. The range is from 0 to 31. number The following special characters are supported: !"#%&'();<=>?[\]
PAGE 1425
secure-cli enable Enable the secured CLI mode. Syntax secure-cli enable Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced this command. The secured CLI mode prevents the users from enhancing the permissions or promoting the privilege levels.
PAGE 1426
Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security. When the passwords are encrypted, you cannot return them to plain text unless you re-configure them. To remove an encrypted password, use the no password password command. To keep unauthorized people from viewing passwords in the switch configuration file, use the service password-encryption command.
PAGE 1427
Related Commands ● privilege level (CONFIGURATION mode) — assign access control to different command modes. show users Allows you to view information on all users logged in to the switch. Syntax Parameters show users [all] all (OPTIONAL) Enter the keyword all to view all terminal lines in the switch. Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific.
PAGE 1428
* 0 console 0 idle 2 vty 0 admin idle 10.16.127.35 3 vty 1 ad idle 10.16.127.145 4 vty 2 ad1 idle 10.16.127.141 5 vty 3 ad1 idle 10.16.127.145 6 vty 4 admin idle 10.16.127.141 7 vty 5 ad idle 10.16.127.141 DellEMC# Related Commands unassigned 1 unassigned 1 unassigned 15 sysadmin 1 sysadmin 1 unassigned 1 unassigned 15 ● username — enables a user. timeout login response Specify how long the software waits for the login input (for example, the user name and password) before timing out.
PAGE 1429
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The software measures the period of inactivity defined in this command as the period between consecutive keystrokes. For example, if your password is “password” you can enter “p” and wait 29 seconds to enter the next letter. username Establish an authentication system based on user names.
PAGE 1430
Usage Information Version Description 9.14(1.0) Introduced dynamic-salt option on the S4810 and S4820T. 9.13.0.0 Enhanced to display a warning message when a weak password is used. Introduced the dynamic-salt option on the MXL, S5000, S4048-ON, S6000, S6000-ON, S3048-ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1431
RADIUS Commands The following RADIUS commands are supported by Dell EMC Networking OS. aaa radius auth-method Configure the authentication method to use with RADIUS for user access. Syntax aaa radius auth-method {pap | mschapv2} To undo the RADIUS authentication method configuration, use the no aaa radius auth-method command. Parameters Defaults pap Enter the keyword pap to use the Password Authentication Protocol (PAP) for RADIUS authentication.
PAGE 1432
● 7 – implies that the key is encrypted and hidden. key Enter a string that is the key to be exchanged between the switch and the dynamic authorization client. The key can be up to 42 characters long. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● It is possible to configure more than one dynamic authorization clients Duplicate (ipv4-addr or ipv6addr or host-name) configurations are not allowed. Command History This guide is platform-specific.
PAGE 1433
To remove the port bounce configuration, enter the no coa-bounce-port command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Configure no coa-bounce-port to drop radius CoA port-bounce requests from the DAC. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command.
PAGE 1434
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. debug radius View RADIUS transactions to assist with troubleshooting. Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1435
Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Time for DAS to wait before the back end response is received. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1436
Usage Information Version Description 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. If this configuration is not enabled, then dynamic authorization messages are not handled by the NAS. ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections.
PAGE 1437
Version Description pre-6.2.1.0 Introduced on the E-Series. port Configures NAS port number to accept CoA or DM requests. Syntax port port-number To remove the NAS port configuration, enter the no port command. Defaults Parameters 3799 port-number Enter the NAS port number to accept CoA and DM requests. The range is from 1 to 65535. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Optionally specify dynamic authorization port number. Default port is 3799.
PAGE 1438
radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped. Syntax radius-server deadtime seconds To disable this function or return to the default value, use the no radius-server deadtime command. Parameters Defaults seconds Enter a number of seconds during which non-responsive RADIUS servers are skipped. The range is from 0 to 2147483647 seconds. The default is 0 seconds.
PAGE 1439
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. DellEMC(conf)# radius-server group group1 DellEMC(conf-radius-group)# radius-server host 1.1.1.
PAGE 1440
key [ encryptiontype ] key (OPTIONAL) Enter the keyword key then an optional encryption-type and a string up to 42 characters long as the authentication key. The RADIUS host server uses this authentication key and the RADIUS daemon operating on this switch. For the encryption-type, enter either zero (0) or 7 as the encryption type for the key entered. The options are: ● 0 is the default and means the password is not encrypted and stored as clear text. ● 7 means that the password is encrypted and hidden.
PAGE 1441
You can use duplicate host names or IP addresses among RADIUS groups. However, you cannot use duplicate host names or IP addresses within the same RADIUS group. If a VRF is not configured on the RADIUS group, then servers configured in the group are considered to be on the default VRF. RADIUS servers that are configured in the CONFIGURATION mode are also considered to be on the default VRF.
PAGE 1442
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000.
PAGE 1443
Usage Information Related Commands Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1444
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1445
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. ● radius-server host — configure a RADIUS host. rate-limit Configure NAS to allow or reject RADIUS dynamic authorization (DA) packets based on the configurable rate limit value.
PAGE 1446
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL.
PAGE 1447
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1448
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections. Syntax ip tacacs source-interface interface To delete a source interface, use the no ip tacacs source-interface command.
PAGE 1449
tacacs-server group Creates a group of TACACS servers. Syntax Parameters Defaults tacacs-server group group-nameTo delete a group of TACACS servers, use the no tacacsserver group group-name command. group-name Enter the name of the TACACS server group. Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific.
PAGE 1450
Defaults port number (OPTIONAL) Enter the keyword port then a number as the port to be used by the TACACS+ server. The range is from zero (0) to 65535. The default is 49. timeout seconds (OPTIONAL) Enter the keyword timeout then the number of seconds the switch waits for a reply from the TACACS+ server. The range is from 0 to 1000. The default is 10 seconds. key key (OPTIONAL) Enter the keyword key then a string up to 42 characters long as the authentication key.
PAGE 1451
Example Related Commands DellEMC(conf)# tacacs-server group group1 DellEMC(conf-tacacs-group)# tacacs-server host 1.1.1.1 key secr-et DellEMC(conf-tacacs-group)# no tacacs-server host 1.1.1.1 DellEMC(conf-tacacs-group)# ● aaa authentication login — specifies the login authentication method. ● tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server key Configure a key for communication between a TACACS+ server and a client.
PAGE 1452
tacacs-server vrf Create an association between a TACACS server group and a VRF and source interface. Syntax tacacs-server vrf vrf-name [source-interface interface] To delete the association between a TACACS server group and a VRF and source interface, use the no tacacs-server vrf vrf-name [source-interface interface] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a TACACS server group with that VRF.
PAGE 1453
Port Authentication (802.1X) Commands An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. Dell EMC Networking OS supports RADIUS and Active Directory environments using 802.1X Port Authentication.
PAGE 1454
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface; dot1x must be enabled both globally and at the interface level.
PAGE 1455
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts then number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3.
PAGE 1456
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1457
Usage Information Version Description 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. 802.1X authentication is enabled when an interface is connected to the switch. If the host fails to respond within a designated amount of time, the authenticator places the port in the guest VLAN. If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable.
PAGE 1458
dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command. Parameters Defaults number Enter the number of times an EAP request is transmitted before a session time-out. The range is from 1 to 10. The default is 2. 2 Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 1459
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1460
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic re-authentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic re-authentication, use the no dot1x reauthentication command.
PAGE 1461
dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters Defaults number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1462
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1463
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs are transmitted by the Authenticator PAE. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters Defaults seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted.
PAGE 1464
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. Defaults none Command Modes ● EXEC ● EXEC privilege Command History Example This guide is platform-specific.
PAGE 1465
Backend State: DellEMC# Initialize DellEMC# show dot1x interface fortyGigE 1/48 802.
PAGE 1466
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 1467
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL debug ip ssh Enables collecting SSH debug information.
PAGE 1468
ip scp topdir Identify a location for files used in secure copy transfer. Syntax ip scp topdir directory To return to the default setting, use the no ip scp topdir command. Parameters Defaults directory Enter a directory name. The internal flash (flash:) is the default directory. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1469
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1470
ip ssh cipher Configure the list of ciphers supported on both SSH client and SCP. Syntax ip ssh cipher cipher-list Parameters Defaults cipher cipher-list Enter the keyword cipher and then a space-delimited list of ciphers that the SSH client supports. The following ciphers are available.
PAGE 1471
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Increased the SSH rate–limit range. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1472
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you enable this command, clients can log in without a password prompt.
PAGE 1473
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. The server-generated key is used for SSHv1 key-exchange. ip ssh mac Configure the list of MAC algorithms supported on both SSH client and SCP. Syntax Parameters ip ssh mac mac-list mac mac-list Enter the keyword mac then a space-delimited list of message authentication code (MAC) algorithms supported by the SSH client. The following MAC algorithms are available.
PAGE 1474
● When FIPS is enabled or disabled, the client MACs get default configuration. ip ssh password-authentication Enable password authentication for the SSH server. Syntax ip ssh password-authentication enable To disable password-authentication, use the no ip ssh password-authentication enable command. Parameters Defaults enable Enter the keyword enable to enable password-authentication for the SSH server.
PAGE 1475
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1476
Parameters Defaults time minutes Enter the keywords time then the amount of time in minutes. The range is from 10 to 1440 minutes. The default is 60 minutes volume rekeylimit Enter the keywords volume then the amount of volume in megabytes. The range is from 1 to 4096 to megabytes. The default is 1024 megabytes The default time is 60 minutes. The default volume is 1024 megabytes. Command Modes CONFIGURATION mode Command History This guide is platform-specific.
PAGE 1477
Example Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC#conf DellEMC(conf)# ip ssh rhostsfile flash://shosts DellEMC(conf)# This command specifies the rhost file used for host-based authentication.
PAGE 1478
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Enabling RSA authentication allows the user to log in without being prompted for a password. In addition, the OpenSSH compatible SSHv2 RSA public key must be added to the list of authorized keys (ip ssh rsa-authentication my-authorized-keys device://filename command).
PAGE 1479
● hmac-sha1 ● hmac-sha1-96 ● hmac-sha2-256 When FIPS is enabled, the default HMAC algorithm is hmac-sha1-96. When FIPS is not enabled, the default HMAC algorithms are the following: ● hmac-md5 ● hmac-md5-96 ● hmac-sha1 ● hmac-sha1-96 ● hmac-sha2-256 kex key-exchangealgorithm Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server.
PAGE 1480
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Removed the support for hmac-sha2-256-96 algorithm. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced the cipher , kex and mac options on the Z9500. 9.5(0.0) Introduced the cipher, kex and mac options on the Z9000, S6000, S4820T, S4810, and MXL.
PAGE 1481
ip ssh server vrf Configure an SSH server on either a specific VRF or a management VRF. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. ip ssh server vrf {any | management | vrf-name} To disable the SSH server configuration, use the no ip ssh server vrf {management | vrfname} command. Parameters Defaults any Enter the keyword any to enable access to the server from any VRF.
PAGE 1482
ip ssh source-interface Specifies an interface’s IP address as the source IP address for an outgoing SSH connections. Syntax ip ssh source-interface interface To delete a source interface, use the no ip ssh source-interface command. Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1483
Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to configure that VRF for an outgoing SSH session. Not configured. Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1484
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1485
Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1486
Usage Information Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1487
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1488
vrf instance (OPTIONAL) E-Series Only: Enter the keyword vrf then the VRF Instance name to open an SSH connection to that instance. ipv4 address (OPTIONAL) Enter the IP address in dotted decimal format A.B.C.D. ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1489
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for the following ciphers and HMAC alogorithms on the Z9000, S6000, S4820T, S4820T. S6000–ON. ● aes128-cbc ● aes192-cbc ● aes256-cbc ● aes128-ctr ● aes192-ctr ● aes256-ctr ● hmac-sha2-256 ● hmac-sha2-256-96 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1490
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1491
Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1492
ip dhcp snooping binding Create a static entry in the DHCP binding table. Syntax [no] ip dhcp snooping binding mac address vlan-id vlan-id ip ip-address interface type slot/port lease number Parameters Defaults mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 1493
ip dhcp snooping database Delay writing the binding table for a specified time. Syntax Parameters Defaults ip dhcp snooping database write-delay minutes minutes The range is from 5 to 21600. none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1494
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1495
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 1496
Related Commands ● ip dhcp snooping trust — configure an interface as trusted. show ip dhcp snooping Display the contents of the DHCP binding table. Syntax show ip dhcp snooping binding Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1497
aaa authorization role-only Configure authentication to use the user’s role only when determining if access to commands is permitted. Syntax aaa authorization role-only To return to the default setting, use the no aaa authentication role-only command. Parameters Defaults name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1498
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1499
router for Router mode Defaults addrole Enter the keyword addrole to add permission to the command. You cannot add or delete rights for the sysadmin role. deleterole Enter the keyword deleterole to remove access to the command. You cannot add or delete rights for the sysadmin role. role-name Enter a text string for the name of the user role up to 63 characters. These are 3 system defined roles you can modify: secadmin, netadmin, and netoperator.
PAGE 1500
Command Modes EXEC Privilege Command History Examples This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1501
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL.
PAGE 1502
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role from scratch.
PAGE 1503
Table 7. Suppressed ICMPv4 message types (continued) ICMPv4 Message Types Router solicitation (10) Time exceeded (11) IP header bad (12) Timestamp request (13) Timestamp reply (14) Information request (15) Information reply (16) Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMPv4 message type Echo request (8). Table 8.
PAGE 1504
drop icmp Drops the ICMPv4 and ICMPv6 packets. Syntax drop {icmp | icmp6} Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other Platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on the S4810, S4820T, S3048–ON, S3100 Series, S4048–ON, S5000, S6000, S6000–ON, Z9500, Z9100–ON, S6100–ON, S6010–ON, S4048T–ON, C9000, and MXL.
PAGE 1505
● A minimum of one upper case letter (A to Z) ● A minimum of one numeric character (0 to 9) ● A minimum of one special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") If your password does not meet the criteria, the system does not accept your password. When you upgrade the Dell EMC Networking OS image, ensure that you upgrade the boot loader. CAUTION: After configuring the boot access password, save it to a secure location.
PAGE 1506
root-access password Configure the root access password. Syntax root-access password [encryption-type] root-password To reset to the default password, use the no root-access password command. Parameters encryption-type (OPTIONAL) Enter an encryption type for the root password that you enter. ● 0 directs the system to store the password as clear text. ● 7 directs the system to store the password with a dynamic salt.
PAGE 1507
Command History Usage Information Example Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, MXL, and FN-IOM. When you reboot the system using the reload command, the system performs OS image verification on the primary boot image.
PAGE 1508
Command Modes CONFIGURATION Command History Example 1508 Security Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM.
PAGE 1509
52 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1510
Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID. The range is from 1 to 4094. count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Debug disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1511
Example Related Command Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1512
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command ● show protocol-tunnel — displays tunneling information for all VLANs.
PAGE 1513
protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters Defaults rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History Example Related Commands This guide is platform-specific.
PAGE 1514
show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax show protocol-tunnel [vlan vlan-id] Parameters Defaults vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094. none Command Modes EXEC Command History Example Example (Specific VLAN) Related Commands 1514 This guide is platform-specific.
PAGE 1515
53 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1516
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6address} agent-addr {ipv4-address | ipv6-address} [number [max-datagramsize number]] | [max-datagram-size number] [vrf management] command.
PAGE 1517
Usage Information Version Description 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
PAGE 1518
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
PAGE 1519
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S-Series, Z-Series, and MXL switch. 9.2(1.0) Introduced on the Z9500. Usage Information When you enable ingress sFlow on an interface, flow sampling is done on any incoming traffic.
PAGE 1520
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Dell EMC Networking OS enhances the sflow implementation for real time traffic analysis on the E-Series to provide extended gateway information in cases where the destination IP addresses are learned by different routing protocols and for cases where the destination is reachable over ECMP.
PAGE 1521
Parameters Defaults interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is 20 seconds. 20 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1522
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1523
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.
PAGE 1524
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1525
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.
PAGE 1526
54 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1527
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1528
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 1529
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
PAGE 1530
RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1531
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1532
snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1533
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
PAGE 1534
The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB. If a community string is configured without a security-name (for example, snmp-server community public ro), the community is mapped to a default security-name/group: ● v1v2creadu / v1v2creadg — maps to a community with ro (read-only) permissions. ● v1v2cwriteu/ v1v2cwriteg — maps to a community with rw (read-write) permissions. The community-name parameter indexes this command.
PAGE 1535
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps.
PAGE 1536
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the following two SNMP notification options: syslog-reachable and syslog-unreachable. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.
PAGE 1537
NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device. If no VRF is specified, then the default VRF is used. udp-port port- number engineID Defaults Enter the keywords udp-port followed by the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. As above. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1538
snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
PAGE 1539
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.2 Added support for the access parameter. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1540
NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps. informs (OPTIONAL) Enter the keyword informs to send inform notifications to the specified host. The default is traps.
PAGE 1541
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148 and S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1542
To 1. 2. 3. 4. 5. Related Commands send an inform, use the following steps: Configure a remote engine ID. Configure a remote user. Configure a group for this user with access rights. Enable traps. Configure a host to receive informs. ● snmp-server enable traps — enables SNMP traps. ● snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server.
PAGE 1543
Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32. Packet sizes are 8000 bytes, 16000 bytes, 32000 bytes, and 64000 bytes. 8 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1544
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1545
remote ip- address Enter the keywords udp-port then the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. vrf vrf-name Enter the keywords vrf and then the name of the VRF this is used to connect to the SNMP server. NOTE: Use this attribute to specify a VRF name that is used to connect to the remote host. If no VRF is specified, then the default VRF is used.
PAGE 1546
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.(0.0) Added aes 128 encryption algorithm parameter. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1547
snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826. RFCs for SNMPv3 define two authentication hash algorithms, namely, HMAC-MD5-96 and HMAC-SHA1-96. These are the full forms or editions of the truncated versions, namely, HMAC-MD5 and HMAC-SHA1 authentication algorithms.
PAGE 1548
not previously set up. Otherwise, you must remove the previously configured users before you change the FIPS mode. Example Related Commands DellEMC# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv aes128 d0452401a8c3ce42804fe80e3ba8763d ● show snmp user — Displays the information configured on each SNMP user name. snmp-server view Configure an SNMPv3 view.
PAGE 1549
Usage Information Example Related Commands The oid-tree variable is a full sub-tree starting from 1.3.6 and cannot specify the name of a sub-tree or a MIB. The following Example configures a view named rview that allows access to all objects under 1.3.6.1. DellEMC# conf DellEMC#(conf) snmp-server view rview 1.3.6.1 included ● show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF.
PAGE 1550
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1551
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1552
default logging buffered Return to the default setting for messages logged to the internal buffer. Syntax default logging buffered Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1553
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging console — set the logging console parameters.
PAGE 1554
Related Commands ● logging monitor — set the logging monitor parameters. ● terminal monitor — send system messages to the terminal/monitor. default logging trap Return to the default settings for logging messages to the Syslog servers. Syntax default logging trap Defaults level = 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1555
Defaults hostname Enter the name of a host already configured and recognized by the switch. udp Enter the keyword udp to enable transmission of log message over UDP followed by port number. The default port is 514 tcp Enter the keyword tcp to enable transmission of log message over TCP followed by port number. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to enable the logging process in VRF mode.
PAGE 1556
logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. Syntax logging buffered [level] [size] To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffered command.
PAGE 1557
logging console Specify which messages are logged to the console. Syntax logging console [level] To return to the default values, use the default logging console command. To disable logging to the console, use the no logging console command. Parameters Defaults level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1558
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1559
● ● ● ● ● ● ● ● ● ● ● ● ● local7 (local use) lpr (line printer system) mail (mail system) news (USENET news) sys9 (system use) sys10 (system use) sys11 (system use) sys12 (system use) sys13 (system use) sys14 (system use) syslog (Syslog process) user (user process) uucp (Unix to Unix copy process) The default is local7. Defaults local7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1560
To return to the default values, use the no logging history command. Parameters Defaults level Indicate a value from 0 to 7 or enter one of the following equivalent words: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 4 or warnings. warnings or 4 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1561
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1562
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1563
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you use the no logging on command, messages are logged only to the console. Related Commands ● ● ● ● logging logging logging logging — enable logging to the Syslog server. buffered — set the logging buffered parameters. console — set the logging console parameters. monitor — set the logging parameters for the terminal connections.
PAGE 1564
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1565
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1566
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5.
PAGE 1567
Example DellEMC(conf)#logging version ? <0-1> Select syslog version (default = 0) DellEMC(conf)#logging version 1 show logging Display the logging settings and system messages logged to the internal buffer of the switch. Syntax Parameters show logging [number | history [reverse][number] | reverse [number] | summary] number (OPTIONAL) Enter the number of messages displayed in the output. The range is from 1 to 65535.
PAGE 1568
Console logging: level debugging Monitor logging: level debugging Buffer logging: level debugging, 5604 Messages Logged, Size (524288 bytes) Trap logging: level informational Oct 8 09:25:37: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 223.80.255.254 closed. Hold time expired Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.13.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.1.1.13 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 1.1.14.
PAGE 1569
Example Related Commands Version Description 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. DellEMC(conf)# show logging auditlog ● clear logging auditlog — clear the audit log. show logging driverlog stack-unit Display the driver log for the specified hardware component.
PAGE 1570
3:Task(tUsrRoot): [ 61]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main block failed errcode 6 4:Task(tUsrRoot): [ 89]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed checksum calulated checksum 0xc9a6 actual chksum 0x0 5:Task(tUsrRoot): [ 57]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed errcode 6 6:Task(tUsrRoot): [ 51]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom, failed to get any good block 7:Task(tUsrRoot): [ 75]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main b
PAGE 1571
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging monitor — set the logging parameters on the monitor/terminal.
PAGE 1572
55 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1573
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
PAGE 1574
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
PAGE 1575
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 TRAP OID Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
PAGE 1576
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1577
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
PAGE 1578
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
PAGE 1579
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
PAGE 1580
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
PAGE 1581
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1582
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
PAGE 1583
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
PAGE 1584
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE lldp-ext-med.
PAGE 1585
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generates an event that is configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
PAGE 1586
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation conflict resolved during audit 113 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
PAGE 1587
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE Object Name MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
PAGE 1588
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1. Above threshold" 133 TR_VLT_DOMAIN _CFG_ERROR 134 DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote there is a error/conflict in the VLT domain config parameters (either locally or in remote node which prevent the peer up.
PAGE 1589
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls. An agent should not generate more than one entConfigChange 'notification-event' in a given time interval (five seconds is the suggested default). A 'notification-event' is the transmission of a single trap or inform PDU to a list of notification destinations.
PAGE 1590
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.23 dellNetSysAlarmCa DELLrdVersionMismatch NETWORKINGCHASSIS-MIB.
PAGE 1591
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
PAGE 1592
56 Stacking All commands in this chapter are specific to the Dell EMC Networking OS. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, see the Stacking S-Series Switches section in the Dell EMC Networking OS Configuration Guide. CAUTION: You cannot enable stacking simultaneously with virtual link trunking (VLT).
PAGE 1593
Usage Information ● To form a mixed-mode stack, use only the 40G ports between the range 49 to 54. ● You cannot form a mixed-mode stack using the 10G ports. Because, the 10G ports on the S4048T are copper ports; where as, the 10G ports on the S4048-ON are SFP ports. ● It is mandatory to enable mixed-mode stacking on the S4048-ON and S4048T-ON switches before joining a mixed-mode stack. ● Stack election is based on the priority or the MAC address of the stack units as in homogenous stacking.
PAGE 1594
Do you System ! Apr 10 config want to reload? Proceed[confirm yes/no]:yes configuration has been modified. Save? [yes/no]: yes 19:19:18: %STKUNIT2-M:CP %FILEMGR-5-FILESAVED: Copied runningto startup-config in flash by default Apr 10 19:19:18: %STKUNIT2-M:CP %CHMGR-5-RELOAD: User request to reload the chassis syncing disks... done unmounting file systems... unmounting /f10/flash (/dev/wd0e)... unmounting /f10/ConfD/db (mfs:479)... unmounting /usr/pkg (/dev/wd0i)... unmounting /boot (/dev/wd0b)...
PAGE 1595
Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the running-config. Related Commands show redundancy — displays the current redundancy status. redundancy force-failover stack-unit Force the standby unit in the stack to become the management unit. Syntax redundancy force-failover stack-unit Defaults Not enabled.
PAGE 1596
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the members option.
PAGE 1597
00:15:01: %STKUNIT2-S:CP %IFMGR-1-DEL_PORT: Removed port: Te 4/1-4/48, Fo 4/51-4/52, DellEMC#00:15:08: %S4048-ON:1 %IFAGT-5-STACK_PORT_LINK_DOWN: Changed stack port state to down: 1/49 00:15:08: %STKUNIT1-M:CP %CHMGR-2-STACKUNIT_DOWN: stack-unit 4 down card removed DellEMC# Related Commands ● reload – reboots Dell EMC Networking OS. show redundancy Display the current redundancy configuration (status of automatic reboot configuration on stack management unit).
PAGE 1598
Failover Type: Auto reboot Stack-unit: Auto failover limit: Hot Failover Enabled 3 times in 60 minutes -- Stack-unit Failover Record ------------------------------------------------Failover Count: 0 Last failover timestamp: None Last failover Reason: None Last failover type: None -- Last Data Block Sync Record: ------------------------------------------------stack-unit Config: succeeded Apr 20 2016 SSMGR: succeeded Apr 20 2016 Start-up Config: succeeded Apr 20 2016 Runtime Event Log: succeeded Apr 19 2016
PAGE 1599
Example Example (Status) Field Description Link Speed Link Speed of the stack port (12 or 42) in Gb/s. Admin Status The only currently listed status is Up. Connection The stack port ID to which this unit’s stack port is connected.
PAGE 1600
3/54 4/53 4/54 5/53 5/54 6/53 6/54 DellEMC# Related Commands 4/53 3/54 5/53 4/54 6/54 1/53 5/54 ● reset stack-unit – resets the designated stack member. ● show hardware stack-unit – displays the data plane or management plane input and output statistics of the designated component of the designated stack member. ● show system – displays the current status of all stack members or a specific member. stack-unit priority Configure the ability of a switch to become the management unit of a stack.
PAGE 1601
Defaults When this value is not set, a switch joining the stack is given the next available sequential stack member identifier. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1602
default configurations on any member ports of the current stack group will be removed when the unit is rebooted. NOTE: Any scripts used to streamline the stacking configuration process must be updated to reflect the Command Mode change from EXEC Privilege to CONFIGURATION to allow the scripts to work correctly. upgrade system stack-unit Copy the boot image or Dell EMC Networking OS from the management unit to one or more stack members.
PAGE 1603
57 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1604
Parameters Defaults interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 1605
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1606
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1607
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1608
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.
PAGE 1609
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter. It is possible, however, that some multicast control traffic may get dropped when storm control thresholds are exceeded.
PAGE 1610
Parameters Defaults pfc-llfc in Enter the keyword pfc-llfc to get the flow control traffic. The range is from 0 to 33554368 packets per second. shutdown Enter the keyword shutdown to shut down the port when the rate exceeds. none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.9(0.
PAGE 1611
Usage Information Version Description 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series. Unknown Unicast Storm-Control is valid for Layer 2 and Layer 2/Layer 3 interfaces. storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only).
PAGE 1612
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
PAGE 1613
58 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1614
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1615
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
PAGE 1616
Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1617
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree — enter SPANNING TREE mode on the switch.
PAGE 1618
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● max-age — changes the wait time before STP refreshes protocol configuration information. ● hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1619
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults seconds Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1620
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1621
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1622
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1623
Example Field Description “Designated port...” Displays the designated port ID. DellEMC# show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
PAGE 1624
Example (Guard) Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1625
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1626
59 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1627
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1628
Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1629
support-assist activity Trigger an activity event immediately. Syntax Parameters support-assist activity {full-transfer | core-transfer} start now full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information. core-transfer Enter the keyword core-transfer to specify transfer of core files. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1630
Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. Introduced the core-transfer and event-transfer parameters. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. By default, each activity follows a set of default actions using a default schedule.
PAGE 1631
Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes. last-name Enter the last name for the contact person. To include a space, enter a space within double quotes. Command Modes SUPPORTASSIST Command History Usage Information This guide is platform-specific.
PAGE 1632
server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode. Syntax server {default | server-name} To delete a server, use the no server server-name command. Parameters Defaults default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred. To include a space, enter a space within double quotes. Default server has URL stor.g3.ph.dell.
PAGE 1633
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
PAGE 1634
Related Commands ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest show — view the list of action-manifest for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. action-manifest remove Remove the action-manifest file from Dell EMC Networking OS. Syntax action-manifest remove } Parameters local-file-name Enter the name of the local action-manifest file.
PAGE 1635
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest install — configure the action-manifest to use for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. enable Enable a specific SupportAssist activity.
PAGE 1636
To remove the complete company contact information, use the no address command. Parameters city company- city province | region | state name (OPTIONAL) Enter the keyword city then the city or town for the company site. To include a space, enter a space within double quotes. (OPTIONAL) Enter the keyword province, region or state then the name of province, region or state for the company site. To include a space, enter a space within double quotes.
PAGE 1637
Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. territory Configure the territory and set the coverage for the company site.
PAGE 1638
Parameters primary email- address alternate emailaddress Enter the keyword primary then the primary email address for the person. Enter the keyword alternate then the alternate email address for the person. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM.
PAGE 1639
Related Commands ● preferred-method — configure the preferred method for contacting the person. preferred-method Configure the preferred method for contacting the person. Syntax Parameters Defaults preferred-method {email | no-contact | phone] email Enter the keyword email to specify email as preferred method. no-contact Enter the keywords no-contact to specify that there is no preferred method. phone Enter the keyword phone to specify phone as preferred method.
PAGE 1640
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. SupportAssist Server Commands Dell EMC Networking OS supports the following SupportAssist Server mode commands. proxy-ip-address Configure a proxy for reaching the SupportAssist remote server.
PAGE 1641
Usage Information The passwords are stored encrypted in the running configuration. enable Enable communication with the SupportAssist server. Syntax enable To disable communication to a specific SupportAssist server, use the no enable command. Defaults Enabled Command Modes SUPPORTASSIST SERVER Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1642
Usage Information The URL should be formatted to follow the ISO format. show eula-consent Display the EULA for the feature. Syntax show eula-consent {support-assist | other feature} Parameters support-assist | other feature Enter the keywords support-assist or the text corresponding to other feature. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1643
allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dells affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
PAGE 1644
preferred-method email time-zone zone +05:30 start-time 12:23 end-time 15:23 ! server Dell enable url http://1.1.1.1:1332 DellEMC# show support-assist status Display information on SupportAssist feature status including any activities, status of communication, last time communication sent, and so on. Syntax show support-assist status Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1645
60 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1646
Defaults end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year.
PAGE 1647
Defaults start-week (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: ● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month. ● last: Enter this keyword to start daylight saving time in the last week of the month.
PAGE 1648
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key. ● clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. ● show clock — displays the current clock settings.
PAGE 1649
Usage Information Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8. debug ntp Display Network Time Protocol (NTP) transactions and protocol messages for troubleshooting.
PAGE 1650
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp authentication-key Specify a key for authenticating the NTP server.
PAGE 1651
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. After configuring the ntp authentication-key command, configure the ntp trusted-key command to complete NTP authentication. Dell EMC Networking OS versions 8.2.1.
PAGE 1652
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option. Syntax ntp control-key-passwd [encryption-type] password To delete the control key, use the no ntp control-key-passwd [encryption-type] password command.
PAGE 1653
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1654
ntp offset-threshold Configure the threshold time interval before which the system generates an NTP audit log message if the time difference from the NTP server is greater than a threshold value (offset-threshold). Syntax ntp offset-threshold threshold-value To disable the threshold value, use the no ntp offset-threshold command. Parameters offset-threshold threshold-value Defaults (Optional) Enter the keyword offset-threshold and then the threshold value. The range is from 0 to 999. Zero (0).
PAGE 1655
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) The trusted-key range value is increased from 1 to 65534. Also, introduced the minpoll and maxpoll polling interval options. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1656
ntp source Specify an interface’s IP address to be included in the NTP packets. Syntax ntp source interface To delete the configuration, use the no ntp source command. Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1657
ntp step-threshold Configure the step-threshold time interval. Syntax ntp step-threshold value To return to the default NTP step-threshold value, use the no ntp step-threshold command. Parameters Defaults value Enter the threshold value in milliseconds. The range is from 128 to 5000 milliseconds (5 seconds). 128 milliseconds Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 1658
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The number parameter in the ntp trusted-key command must be the same number as the number parameter in the ntp authentication-key command.
PAGE 1659
Example Example (Detail) Related Commands DellEMC#show clock 11:05:56.949 UTC Thu Oct 25 2001 DellEMC# DellEMC# show clock detail 12:18:10.691 UTC Wed Jan 7 2009 Time source is RTC hardware Summer time starts 02:00:00 UTC Sun Mar 8 2009 Summer time ends 02:00:00 ABC Sun Nov 1 2009 DellEMC# ● clock summer-time recurring — displays the time and date from the switch hardware clock. show ntp associations Display the NTP master and peers.
PAGE 1660
Field Description ● - means the peer is a candidate for selection. ● x means designated falsesticker by the intersection algorithm. Example (without ntp master configuration) Example (with ntp master configuration) remote Displays the remote IP address of the NTP peer. ref clock Displays the IP address of the remote peer’s reference clock. st Displays the peer’s stratum, that is, the number of hops away from the external time source. A in this column means the NTP peer cannot reach the time source.
PAGE 1661
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added support for VRF. 9.4.(0.0) Added support for VRF.
PAGE 1662
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp status command shown in the Example below. Field Description “Clock is...” States whether or not the switch clock is synchronized, which NTP stratum the system is assigned and the IP address of the NTP peer. “frequency is...
PAGE 1663
61 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1664
Usage Information The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
PAGE 1665
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
PAGE 1666
Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1667
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000.
PAGE 1668
tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit value To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters Defaults value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64.
PAGE 1669
Defaults Tunnel keepalive is disabled. Command Modes INTERFACE TUNNEL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1670
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. To enable a tunnel interface, use this command.
PAGE 1671
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the tunnel source anylocal command. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. Added an optional keyword “anylocal” to the tunnel source command.
PAGE 1672
62 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1673
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1674
Related Commands ● clear ufd-disable — re-enable downstream interfaces that are in a UFD-Disabled Error state. description Enter a text description of an uplink-state group. Syntax description text Parameters Defaults text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific.
PAGE 1675
Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. If a 40G port is fanned-out into 10G ports, the range is entered as slot/sort/ subport-slot/port/subport. Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific.
PAGE 1676
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1677
If all upstream interfaces in an uplink-state group go down, all downstream interfaces in the same uplink-state group are put into a link-down state. Related Commands ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. ● uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. enable Enable uplink state group tracking for a specific UFD group.
PAGE 1678
Example Related Commands Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1679
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1680
Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/25(Up) Te 1/28(Up) Downstream Interfaces : Te 5/1(Up) Te 5/1(Up) Te 5/3(Up) Te 5/5(Up) Te 5/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 1/1(Dwn) Te 1/3(Dwn) Te 1/5(Dwn) Downstream Interfaces : Te 5/2(Dis) Te 5/4(Dis) Te 5/11(Dis) Te 5/12(Dis) Te 5/13(Dis) Te 5/14(Dis) Te 5/15(Dis) Uplink State Group : 6 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 7 Status: Enabled,
PAGE 1681
An uplink-state group is considered operationally up if at least one upstream interface in the group is in the Link-Up state. An uplink-state group is considered operationally down if no upstream interfaces in the group are in the Link-Up state. No uplink-state tracking is performed when a group is disabled or in an operationally down state. To disable upstream-link tracking without deleting the uplink-state group, use the no enable command in uplink-state-group configuration mode.
PAGE 1682
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. You can assign physical port or port-channel interfaces to an uplink-state group. You can assign an interface to only one uplink-state group.
PAGE 1683
63 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1684
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. When packets are colored green; no packets are dropped.
PAGE 1685
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. S4048–ON Syntax Parameters Defaults dei mark {green | yellow} {0 | 1} 0|1 Enter the bit value you want to map to a color. green | red | yellow Choose a color: ● Green: High priority packets that are the least preferred to be dropped.
PAGE 1686
member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a Port Channel interface, enter the keywords port-channel, and then a number.
PAGE 1687
stack-group-id Enter the stack group ID. The range is from 0 to 16. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1688
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to enabling this command, to place the interface in Layer 2 mode, enter the switchport command.
PAGE 1689
Version Description E-Series original Command Usage Information Prior to disabling the stackable VLAN feature, remove the members. To view the stackable VLANs, use the show vlan command in EXEC Privilege mode. Stackable VLANs contain members, designated by the M in the Q column of the command output. If you enabled VRF, you cannot enable the stacked VLAN feature using this command. If you enabled IGMP snooping, you cannot enable the stacked VLAN feature using this command.
PAGE 1690
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. You can separate the C-Tag values by commas or dashed ranges. In the case of conflicts, dynamic mode CoS overrides any Layer 2 QoS configuration.
PAGE 1691
Usage Information For specific interoperability limitations regarding the S-Tag TPID, see the Dell EMC Networking OS Configuration Guide. The four characters you may enter are shown in the following table. Related Commands Number Resulting TPID 1 0x0001 10 0x0010 81 0x0081 8100 0x8100 ● portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays.
PAGE 1692
Version Description E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, use the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. In Example 1, a VLAN-Stack trunk port is configured and then made part of a single-tagged VLAN. In Example 2, the tag protocol identifier (TPID) is set to 88A8.
PAGE 1693
DellEMC(conf-if-te-5/1)# vlan-stack trunk DellEMC(conf-if-te-5/1)# exit DellEMC(config)# interface vlan 10 DellEMC(conf-if-vlan)# vlan-stack compatible DellEMC(conf-if-vlan)# member Te 4/1, Te 3/10, TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# interface vlan 30 DellEMC(conf-if-vlan)# untagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# DellEMC(config)# interface vlan 40 DellEMC(conf-if-vlan)# tagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# VLAN Stacking 1693
PAGE 1694
64 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • ip vrf ip http vrf description ip vrf forwarding ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip vrf Create or delete a customer VRF.
PAGE 1695
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 1696
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
PAGE 1697
you assign two interfaces to the same VRF, you cannot configure overlapping IP subnets or the same IP address to them. Example DellEMC# configure terminal DellEMC(conf)# ip vrf red DellEMC(conf-vrf)# description "Red Network" DellEMC(conf-vrf)# show config ! ip vrf red 4 description "Red Network" DellEMC(conf-vrf)# DellEMC(conf-if-te-1/45)# int te 7/46 DellEMC(conf-if-te-1/46)# no shut DellEMC(conf-if-te-1/46)# ip vrf forwarding red DellEMC(conf-if-te-1/46)# ip add 100.1.1.
PAGE 1698
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, you can use the ip route-export tag command without specifying the route-map attribute. This action exposes source VRF routes to various other VRFs, which then import these routes using the ip route-import tag command.
PAGE 1699
Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. ● ip route-export – exports routes to another VRF. ipv6 route-export Enables route leaking between VRFs.
PAGE 1700
Only active routes are eligible for leaking. For example, if one VRF has two routes corresponding to BGP and OSPF, in which the BGP route is not active, the OSPF route takes precedence over BGP. Even though the target VRF has specified filtering options to match BGP, the BGP route is not leaked as that route is not active in the source VRF. Related Commands ● ipv6 route-import – imports IPv6 routes from another VRF.
PAGE 1701
Parameters bgp Enter the keyword bgp to leak or share routes corresponding to the BGP protocol. isis Enter the keyword isis to leak or share routes corresponding to the ISIS protocol. ospf Enter the keyword ospf to leak or share routes corresponding to the OSPF protocol. connected Enter the keyword connected to leak or share connected routes corresponding to the VRF. static Enter the keyword static to leak or share static routes corresponding to the VRF.
PAGE 1702
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. ● ip route-import — import routes from another VRF.
PAGE 1703
To remove the limit on the maximum number of routes used, use the no maximum dynamic-routes command. Parameters limit Maximum number of routes allowed in a VRF. The valid range is from 1 to 16,000 (or maximum allowable for that platform if a smaller value). warningthreshold The warning threshold value is a percentage of the limit value. When the number of routes reaches the specified percentage of the limit, a warning message appears. The valid range is from 1 to 100.
PAGE 1704
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 1705
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. This command displays information from the running-config corresponding to either a specific VRF or all the VRFs in the system.
PAGE 1706
65 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1707
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1708
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1709
Usage Information Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link.
PAGE 1710
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. S4048–ON Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1711
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1712
66 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1713
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax Parameters Defaults back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1714
clear vlt statistics Clear the VLT operation statistics. Syntax clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP.
PAGE 1715
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax Parameters Defaults delay-restore delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1716
This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap). Defaults 60 seconds Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1717
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. LACP on the VLT ports (on a VLT switch or access device), which are members of the VLT, are not brought up until the VLT domain is recognized on the access device.
PAGE 1718
Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1719
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan option. 8.3.8.0 Introduced on the S4810. To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option.
PAGE 1720
peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 65535. The default value is infinity. Command Modes VLT DOMAIN (conf-vlt-domain) Default Infinity Command History This guide is platform-specific.
PAGE 1721
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1722
Usage Information Example (Brief) Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell EMC Networking OS version number. VLT version numbers begin with odd numbers.
PAGE 1723
Example Version Description 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays counter information.
PAGE 1724
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) If you do not add a parameter such as arp or mac, the output displays all the counters.
PAGE 1725
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1726
-----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.2) VLAN 15 DellEMC# --------VLAN 6 te 1/5 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show mismatch in VXLAN instance parameters. 9.10(0.
PAGE 1727
VLAN to VNI config mismatch -------------------------------------Vlan-ID Local VNID Peer VNID -----------------------------10 10 11 11 12 12 13 13 - VXLAN enabled status on VLT Port Channels ------------------------------------------Local-Lag Status Peer-Lag Status -----------------------------300 Disable 100 Disable 700 Enable 812 Disable 999 Disable 888 Disable Local VTEP IP mismatch ------------------------------------------------------------------Local Node “Local VTEP IP” Remote Node “Local VTEP IP”
PAGE 1728
Local Lag --------128 Peer Lag Local VLANs -------- ----------128 4094 Peer VLANs ---------100 DellEMC# show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific.
PAGE 1729
show vlt statistics Displays VLT operations statistics. Syntax Parameters Default show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] arp Enter the keyword arp to display the ARP VLT statistics. domain Enter the keyword domain to display the domain VLT statistics. igmp-snoop Enter the keywords igmp-snoop to display the IGMP snooping VLT statistics. mac Enter the keyword mac to display the VLT MAC addresses VLT statistics.
PAGE 1730
VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg Response rcvd: 1 IGMP PDU Tunnel Pkt sent: 5 IGMP PDU Tunnel Pkt rcvd: 10 IGMP Tunnel PDUs sent: 10 IGMP Tun
PAGE 1731
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1732
unit-id Configure the default unit ID of a VLT peer switch. Syntax unit-id [0 | 1] Parameters Defaults 0|1 Configure the default unit ID of a VLT peer switch. Enter 0 for the first peer. Enter 1 for the second peer. Automatically assigned based on the MAC address of each VLT peer. The peer with the lower MAC address is assigned unit 0; the peer with the higher MAC address is assigned unit 1. Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific.
PAGE 1733
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 1734
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. show vlt private-vlan Display the private VLAN (PVLAN) associated with the VLT LAG for VLT peer nodes. Syntax show vlt private-vlan Command Modes EXEC Command History Usage Information This guide is platform-specific.
PAGE 1735
67 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
PAGE 1736
all Enter the keyword all to clear both MAC address of the VXLAN and legacy VLAN. interface Enter the keyword interface to clear MAC address from a specific interface. vlan Enter the keyword vlan to clear MAC address from a specific vlan. vxlan Enter the keyword vxlan to clear MAC address from a specific vxlan. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1737
Defaults tcp (OPTIONAL) Enter the keyword tcp to configure tcp connection to controller. ssl (OPTIONAL) Enter the keyword ssl to configure ssl connection to controller (Default). Disabled Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1738
debug vxlan Debug messages between the Gateway and Controller. Syntax debug vxlan Defaults Disabled Command Modes EXEC Privilege Command History Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S6000.
PAGE 1739
fail-mode Configures failure-mode on the platform. Syntax fail-mode secure To disable the fail-mode secure, use the no fail-mode securecommand. Parameters Defaults secure Enter the keyword secure to delete all its database and hardware flows/ resources, when the VTEP loses connectivity with the controller. non secure Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific.
PAGE 1740
local-vtep-ip Set the local IP Address to be used as the source IP for VXLAN tunnels. Syntax local-vtep-ip IP Address To disable the settings, use the no local-vtep-ip command. Parameters Defaults IP Address Enter the local IP Address to be used as a source for VXLAN tunnels. None. Command Modes VXLAN INSTANCE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1741
peer-ovsdbserver-ip Specify the IP address of the peer OVSDB server in a VLT setup. Syntax peer-ovsdbserver-ip peer-ip-address To remove the configuration, use the no peer-ovsdbserver-ip Parameters Defaults peer-ip-address Enter the peer OVSDB server IP address. This is usually the management IP address of the peer VLT device. Not configured Command Modes VXLAN-INSTANCE Command History This guide is platform-specific.
PAGE 1742
Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile. The range is from 1 to 16777215. None. Command Modes VNI-PROFILE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON.
PAGE 1743
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced nsx and Nuage keywords on the S5048F–ON. 9.13(0.0) Introduced nsx and Nuage keywords on the S4048–ON, S4048T-ON, S6000, S6000–ON, S6100–ON, S6010–ON, and Z9100–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1744
Version Description 9.8(0.0) Introduced on the S4048–ON. 9.4(0.0) Introduced on the S6000. Usage Information You must disable vxlan-instance before unconfiguring VAP. Related Commands feature vxlan — Enable VXLAN configuration globally on the platform. vxlan-instance loopback Provision VXLAN and non-VXLAN loopback ports that support routing in and out of VXLAN tunnels and enable MAC level loopback on all these ports.
PAGE 1745
vnid Associate a range of VNID numbers to a specific VNI profile. Syntax vnid VNID-Range To remove the association, use the no vnid command. Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile. The range is from 1 to 16777215. None. Command Modes VNI-PROFILE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1746
Parameters Defaults instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. static Enter the keyword static to set the VXLAN instance in static mode. Controller mode. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1747
show running-config vxlan Displays the VXLAN configuration information from running configuration. Syntax show running-config vxlan Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.
PAGE 1748
Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.
PAGE 1749
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1750
Example Related Commands Version Description 9.4.(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) vxlan-instance — Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics interface Displays the port VLAN statistics information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1751
show vxlan vxlan-instance statistics remote-vtep-ip Displays VXLAN statistics for a specific VXLAN tunnel. Syntax Parameters show vxlan vxlan-instance instance ID statistics remote-vtep-ip IP Address instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. remote-vtep-ip Enter the keyword remote-vtep-ip followed by the IP Address of the remote VTEP. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1752
Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. Introduced on the Z9100–ON. Example Related Commands 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1753
Example Related Commands Version Description 9.4(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 unicast-mac-remote Total Remote Mac Count: 1 VNI MAC TUNNEL 100 00:00:07:00:02:00 (N) 60.1.1.1 vxlan-instance- Enable VXLAN Instance configuration on the platform.
PAGE 1754
68 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1755
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1756
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax clear counters vrrp [vrrp-id] [ipv6] Parameters vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1757
between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups.
PAGE 1758
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group. Syntax description text To delete a VRRP group description, use the no description command. Parameters Defaults text Enter a text string up to 80 characters long.
PAGE 1759
To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1760
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1761
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command.
PAGE 1762
If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration. Syntax show config [verbose] Parameters verbose (OPTIONAL) Enter the keyword verbose to view all the VRRP group configuration information, including default information. Command Modes VRRP Command History Example This guide is platform-specific.
PAGE 1763
Parameters vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups. interface type (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1764
Item Description ● Y = Preempt is enabled. ● N = Preempt is not enabled. Example (Brief) Usage Information State Displays the operational state of the interface using one of the following: ● NA/IF (the interface is not available). ● MASTER (the interface associated with the MASTER router). ● BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router.
PAGE 1765
Example Example (VRRP VRF) DellEMC> show vrrp -----------------TenGigabitEthernet 1/3, VRID: 1, Net: 10.1.1.253 VRF: 0 default State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
PAGE 1766
track Monitor an interface and lower the priority value of the VRRP group on that interface if it is disabled. Syntax track interface [priority-cost cost] To disable monitoring, use the no track interface command. Parameters Defaults interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1767
... ip-address12 Defaults (OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted decimal format. Separate the IP addresses with a space. The IP addresses must be on the same subnet as the interface’s primary IP address. Not configured. Command Modes VRRP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1768
Version Description 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information This command applies to a single interface. When you use this command with the vrrp delay reload command, the later timer rules VRRP enabling.
PAGE 1769
Usage Information This command applies to all the VRRP interfaces on a system. When you use this command with the vrrp delay minimum command, the later timer rules VRRP enabling. For example, if vrrp delay reload is 600 and vrrp delay minimum is 300: ● When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 1770
version Set the VRRP protocol version for the IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters Defaults 2 Enter the keyword 2 to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the keyword 3 to specify VRRP version 3 as defined by RFC 5798, Virtual Router Redundancy Protocol. both Enter the keyword both for in-service migration from VRRP version 2 to VRRP version 3.
PAGE 1771
● debug vrrp ipv6 ● show vrrp ipv6 ● vrrp-ipv6-group The following commands apply to IPv4 and IPv6: ● advertise-interval ● description ● disable ● hold-time ● preempt ● priority ● show config ● virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups. Syntax Parameters clear counters vrrp ipv6 [vrid | vrf vrf-name] vrid (OPTIONAL) Enter the number of an IPv6 VRRP group; range is from 1 to 255.
PAGE 1772
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/ [subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp ipv6 Enable VRRP debugging.
PAGE 1773
Usage Information If you do not specify an option, debugging is active on all interfaces and all VRRP groups. show vrrp ipv6 View the active IPv6 VRRP groups. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group. Syntax Parameters show vrrp ipv6 [vrid] [interface] [brief] [vrf vrf-name] vrid (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255.
PAGE 1774
Line starting with Description VRF VRF instance to which the VRRP group interface belongs. State: master... Displays the interface’s state: ● Na/If (not available) ● master (MASTER virtual router) ● backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:... Displays additional VRRP configuration information: ● Hold Down displays the hold down timer interval in seconds.
PAGE 1775
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1776
69 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1777
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax Parameters Defaults crypto ca-cert install path path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1778
● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1779
email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect. For self-signed certificates, if validity is not specified, it defaults to 3650 days, or 10 years. length length (OPTIONAL) Enter the keyword length followed by a bit length value.
PAGE 1780
Parameters cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored. Following are example of a path that you can specify: flash://certs/s4810-001-request.crtand usbflash:/certs/s4810-001-cert.
PAGE 1781
If the system is in non-FIPS mode, the certificate will be installed as the non-FIPS certificate. When FIPS mode is enabled/disabled, the certificates (and keys) are switched by the system. Related Commands ● crypto ca-cert install crypto x509 ocsp Configures the OCSP behavior. Syntax Parameters Defaults crypto x509 ocsp [nonce] [sign-requests] nonce Enter the keyword nonce to use the nonce feature for the OCSP requests to OCSP responder communication.
PAGE 1782
Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Related Commands Version Description 9.11.0.0 Introduced this command.
PAGE 1783
tcp Enter the keyword tcp to enable TCP. udp Enter the keyword udp to enable UDP. vrf vrf-name Enter the keyword vrf followed by the name of the VRF. sha1 fingerprint Enter the keyword sha1 followed by the finger print. This option is only available when the secure option is configured. This new option enables the Syslog feature to compare the received certificate’s sha-1 fingerprint against this configured sha-1 fingerprint.
PAGE 1784
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin When you use this command, the device maps the current certificate context in the certificate store to a CA certificate through the subject key identifier field. The subject key identifier field contains the SHA-1 hash of the CA’s public key. This configuration provides a way to uniquely identify a CA and associate it with any CA-specific settings.
PAGE 1785
Related Commands ● crypto x509 ocsp ocsp-server prefer Configures OCSP responder preference. You can configure the preference or order that the CA or a device should follow while contacting multiple OCSP responders. Syntax ocsp-server prefer Defaults None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1786
show crypto cert Displays the certificate information that is specified. Syntax show crypto cert {path} Parameters Defaults path (OPTIONAL) Enter the path to a local file where a certificate chain is stored in PEM format. If a path is not specified, display the certificate that is currently installed on the system. None. Command Modes EXEC Privilege Command History This guide is platform-specific.