Administrator Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Dell Configuration Guide for the S6000

System

9.14.2.8

September 2020

Rev. A00

Summary of content (1141 pages)

PAGE 1
Dell Configuration Guide for the S6000 System 9.14.2.8 September 2020 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide.........................................................................................................32 Audience.............................................................................................................................................................................. 32 Conventions........................................................................................................................................................................
PAGE 4
Moving a Command from EXEC Privilege Mode to EXEC Mode.................................................................... 56 Allowing Access to CONFIGURATION Mode Commands................................................................................. 56 Allowing Access to Different Modes...................................................................................................................... 56 Applying a Privilege Level to a Username...........................................................
PAGE 5
Enabling 802.1X..................................................................................................................................................................86 Configuring dot1x Profile ................................................................................................................................................ 87 Configuring MAC addresses for a do1x Profile...........................................................................................................
PAGE 6
Applying Egress Layer 3 ACLs (Control-Plane)..................................................................................................120 IP Prefix Lists....................................................................................................................................................................120 Configuration Task List for Prefix Lists.................................................................................................................121 ACL Remarks...............
PAGE 7
Enabling four-byte autonomous system numbers..............................................................................................179 Changing a BGP router ID....................................................................................................................................... 180 Configuring AS4 Number Representations..........................................................................................................180 Configuring a BGP peer....................................
PAGE 8
Unified Forwarding Table (UFT) Modes....................................................................................................................234 Configuring UFT Modes...........................................................................................................................................234 Chapter 11: Control Plane Policing (CoPP)................................................................................ 236 Configure Control Plane Policing..................................
PAGE 9
DCBx Example............................................................................................................................................................267 DCBx Prerequisites and Restrictions................................................................................................................... 268 Configuring DCBx......................................................................................................................................................
PAGE 10
Configuring the Hash Algorithm............................................................................................................................ 308 Enabling Deterministic ECMP Next Hop............................................................................................................. 308 Configuring the Hash Algorithm Seed................................................................................................................. 309 Link Bundle Monitoring............................
PAGE 11
Creating the FRRP Group........................................................................................................................................341 Configuring the Control VLAN................................................................................................................................341 Configuring and Adding the Member VLANs..................................................................................................... 342 Setting the FRRP Timers.....................
PAGE 12
Configuring Layer 2 (Data Link) Mode................................................................................................................ 375 Configuring Layer 2 (Interface) Mode................................................................................................................. 375 Configuring Layer 3 (Network) Mode..................................................................................................................376 Configuring Layer 3 (Interface) Mode.................
PAGE 13
Auto-Negotiation on Ethernet Interfaces................................................................................................................. 407 Setting the Speed of Ethernet Interfaces.......................................................................................................... 408 Set Auto-Negotiation Options............................................................................................................................... 409 View Advanced Interface Information.........
PAGE 14
Extended Address Space........................................................................................................................................ 432 Stateless Autoconfiguration................................................................................................................................... 432 IPv6 Headers..............................................................................................................................................................
PAGE 15
Multi-Topology IS-IS...................................................................................................................................................... 462 Transition Mode.........................................................................................................................................................462 Interface Support....................................................................................................................................................
PAGE 16
Chapter 27: Layer 2................................................................................................................... 499 Manage the MAC Address Table................................................................................................................................ 499 Clearing the MAC Address Table.......................................................................................................................... 499 Setting the Aging Time for Dynamic Entries.............
PAGE 17
Relevant Management Objects................................................................................................................................... 530 Chapter 29: Microsoft Network Load Balancing......................................................................... 534 Configuring a Switch for NLB .................................................................................................................................... 535 Enabling a Switch for Multicast NLB..........................
PAGE 18
MSTP Sample Configurations...................................................................................................................................... 567 Debugging and Verifying MSTP Configurations...................................................................................................... 570 Chapter 32: Multicast Features................................................................................................. 572 Enabling IP Multicast............................................
PAGE 19
Assigning Area ID on an Interface......................................................................................................................... 623 Assigning OSPFv3 Process ID and Router ID Globally.....................................................................................623 Assigning OSPFv3 Process ID and Router ID to a VRF................................................................................... 624 Configuring Stub Areas......................................................
PAGE 20
Configuring Monitor Multicast Queue....................................................................................................................... 663 Flow-Based Monitoring................................................................................................................................................. 664 Enabling Flow-Based Monitoring...........................................................................................................................
PAGE 21
Displaying WRED Drop Statistics............................................................................................................................711 Displaying egress–queue Statistics........................................................................................................................ 711 Pre-Calculating Available QoS CAM Space...............................................................................................................
PAGE 22
Chapter 45: Security................................................................................................................. 748 AAA Accounting...............................................................................................................................................................748 Configuration Task List for AAA Accounting......................................................................................................748 RADIUS Accounting................................
PAGE 23
Dell EMC Networking OS Image Verification..................................................................................................... 803 Startup Configuration Verification........................................................................................................................804 Configuring the root User Password....................................................................................................................805 Enabling User Lockout for Failed Login Attempts......
PAGE 24
Configuration Task List for SNMP.............................................................................................................................. 831 Important Points to Remember....................................................................................................................................831 Set up SNMP...................................................................................................................................................................
PAGE 25
Global MIB objects for port security.................................................................................................................... 865 MIB support for interface level port security.....................................................................................................865 MIB objects for configuring MAC addresses..................................................................................................... 866 MIB objects for configuring MAC addresses.................
PAGE 26
Troubleshoot a Stack.....................................................................................................................................................896 Recover from Stack Link Flaps..............................................................................................................................896 Recover from a Card Problem State on a Stack...............................................................................................896 Chapter 50: Storm Control............
PAGE 27
Disabling NTP on an Interface............................................................................................................................... 926 Configuring a Source IP Address for NTP Packets.......................................................................................... 926 Configuring NTP Authentication........................................................................................................................... 927 Configuring NTP control key password...............
PAGE 28
VLT Terminology....................................................................................................................................................... 956 Layer-2 Traffic in VLT Domains.............................................................................................................................957 Interspersed VLANs..................................................................................................................................................
PAGE 29
Configuring an LLDP VLT Proxy Gateway.............................................................................................................. 1025 VLT Proxy Gateway Sample Topology.....................................................................................................................1026 VLT Domain Configuration.................................................................................................................................... 1026 Dell-1 VLT Configuration..................
PAGE 30
Configuring Management VRF.............................................................................................................................1065 Configuring a Static Route....................................................................................................................................1066 Sample VRF Configuration..........................................................................................................................................1066 Route Leaking VRFs........
PAGE 31
Open Shortest Path First (OSPF)........................................................................................................................1125 Intermediate System to Intermediate System (IS-IS).....................................................................................1126 Routing Information Protocol (RIP)..................................................................................................................... 1127 Multicast..................................................
PAGE 32
1 About this Guide This guide describes the protocols and features the Dell EMC Networking Operating System (OS) supports and provides configuration instructions and examples for implementing them. For complete information about all the CLI commands, see the Dell EMC Command Line Reference Guide for your system. The S6000 platform is available with Dell EMC Networking OS version 9.0(2.0) and beyond. Though this guide contains information about protocols, it is not intended to be a complete reference.
PAGE 33
2 Configuration Fundamentals The Dell EMC Networking Operating System (OS) command line interface (CLI) is a text-based interface you can use to configure interfaces and protocols. The CLI is largely the same for each platform except for some commands and command outputs. The CLI is structured in modes for security and management purposes. Different sets of commands are available in each mode, and you can limit user access to modes using privilege levels.
PAGE 34
● EXEC mode is the default mode and has a privilege level of 1, which is the most restricted level. Only a limited selection of commands is available, notably the show commands, which allow you to view system information. ● EXEC Privilege mode has commands to view configurations, clear counters, manage configuration files, run diagnostics, and enable or disable debug operations. The privilege level is 15, which is unrestricted.
PAGE 35
ROUTE-MAP ROUTER BGP BGP ADDRESS-FAMILY ROUTER ISIS ISIS ADDRESS-FAMILY ROUTER OSPF ROUTER OSPFV3 ROUTER RIP SPANNING TREE SUPPORTASSIST TRACE-LIST VLT DOMAIN VRRP UPLINK STATE GROUP uBoot Navigating CLI Modes The Dell EMC Networking OS prompt changes to indicate the CLI mode. The following table lists the CLI mode, its prompt, and information about how to access and exit the CLI mode.
PAGE 36
Table 1.
PAGE 37
Table 1.
PAGE 38
The do Command You can enter an EXEC mode command from any CONFIGURATION mode (CONFIGURATION, INTERFACE, SPANNING TREE, and so on.) without having to return to EXEC mode by preceding the EXEC mode command with the do command. The following example shows the output of the do command.
PAGE 39
no ip address no shutdown Layer 2 protocols are disabled by default. To enable Layer 2 protocols, use the no disable command. For example, in PROTOCOL SPANNING TREE mode, enter no disable to enable Spanning Tree. Obtaining Help Obtain a list of keywords and a brief functional description of those keywords at any CLI mode using the ? or help command: ● To list the keywords available in the current mode, enter ? at the prompt or after a keyword.
PAGE 40
Short-Cut Key Action Combination CNTL-K Deletes all characters from the cursor to the end of the command line. CNTL-L Re-enters the previous command. CNTL-N Return to more recent commands in the history buffer after recalling commands with CTRL-P or the UP arrow key. CNTL-P Recalls commands, beginning with the last command. CNTL-R Re-enters the previous command. CNTL-U Deletes the line. CNTL-W Deletes the previous word. CNTL-X Deletes the line.
PAGE 41
The except keyword displays text that does not match the specified text. The following example shows this command used in combination with the show system brief command. Example of the except Keyword DellEMC#show system brief | except 1 Stack MAC Reload-Type : 4c:76:25:e5:49:40 : normal-reload [Next boot : normal-reload] The find keyword displays the output of the show command beginning from the first occurrence of specified text.
PAGE 42
EXEC Privilege mode show alias Example of the show alias Command DellEMC# configure terminal DellEMC(config)# alias-definition DellEMC(conf-alias-definition)# alias ns no shutdown DellEMC(conf-alias-definition)# alias 10gint interface TenGigabitEthernet $1 Viewing alias configuration To view the Alias configurations, use the following commands: 1. Display the complete list of aliases and its definitions.
PAGE 43
3 Getting Started This chapter describes how you start configuring your system. When you power up the chassis, the system performs a power-on self test (POST) and system then loads the Dell EMC Networking Operating System. Boot messages scroll up the terminal window during this process. No user interaction is required if the boot process proceeds without interruption. When the boot process completes, the system status LEDs remain online (green) and the console monitor displays the EXEC mode prompt.
PAGE 44
Accessing the Console Port To access the console port, follow these steps: For the console port pinout, refer to Accessing the RJ-45 Console Port with a DB-9 Adapter. 1. Install an RJ-45 copper cable into the console port. Use a rollover (crossover) cable to connect the console port to a terminal server. 2. Connect the other end of the cable to the DTE terminal server. 3.
PAGE 45
Accessing the System Remotely You can configure the system to access it remotely by Telnet or secure shell (SSH). ● The platform has a dedicated management port and a management routing table that is separate from the IP routing table. ● You can manage all Dell EMC Networking products in-band via the front-end data ports through interfaces assigned an IP address as well. Accessing the System Remotely Configuring the system for remote access is a three-step process, as described in the following topics: 1.
PAGE 46
username name [access-class access-list-name] [nopassword | {password | secret | sha256– password} [encryption-type] password [dynamic-salt]] [privilege level] [role role-name] ○ name: Enter a text string upto 63 characters long. ○ access-class access-list-name: Enter the name of a configured IP ACL. ○ nopassword: Allows you to configure an user without the password. ○ password: Allows you to configure an user with a password. ○ secret: Specify a secret string for an user.
PAGE 47
○ encryption-type: specifies how you input the password, is 0 by default, and is not required. ￭￭￭￭ 0 is to input the password in clear text. 5 is to input a password that is already encrypted using MD5 encryption method. Obtain the encrypted password from the configuration file of another device. 7 is to input a password that is already encrypted using DES encryption method. Obtain the encrypted password from the configuration file of another device.
PAGE 48
Destination file name [Dell-EF-8.2.1.0.bin.bin]: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 26292881 bytes successfully copied Mounting an NFS File System This feature enables you to quickly access data on an NFS mounted file system. You can perform file operations on an NFS mounted file system using supported file commands. This feature allows an NFS mounted device to be recognized as a file system.
PAGE 49
Destination file name [test.txt]: User name to login remote host: username Password to login remote host: ! Example of Copying to NFS Mount DellEMC#copy flash://test.txt nfsmount:/// Destination file name [test.txt]: ! 15 bytes successfully copied DellEMC#copy flash://test/capture.txt.pcap nfsmount:/// Destination file name [test.txt]: ! 15 bytes successfully copied DellEMC#copy flash://test/capture.txt.pcap nfsmount:///username/snoop.pcap ! 24 bytes successfully copied DellEMC# DellEMC#copy tftp://10.16.
PAGE 50
Configure the Overload Bit for a Startup Scenario For information about setting the router overload bit for a specific period of time after a switch reload is implemented, see the Intermediate System to Intermediate System (IS-IS) section in the Dell Command Line Reference Guide for your system. Viewing Files You can only view file information and content on local file systems. To view a list of files or the contents of a file, use the following commands. ● View a list of files on the internal flash.
PAGE 51
Managing the File System The Dell EMC Networking system can use the internal Flash, external Flash, or remote devices to store files. The system stores files on the internal Flash by default but can be configured to store files elsewhere. To view file system information, use the following command. ● View information about each file system.
PAGE 52
[May 17 15:43:08]: CMD-(CLI):[end]by default from console [May 17 15:43:16]: CMD-(CLI):[show logging]by default from console [May 17 15:43:22]: CMD-(CLI):[show command-history]by default from console DellEMC# Example 2: service timestamps log datetime utc DellEMC(conf)#service timestamps log datetime utc DellEMC# show command-history - Repeated 1 time. [May 17 15:46:44]: CMD-(CLI):[configure]by default from console - Repeated 1 time.
PAGE 53
Upgrading Dell EMC Networking OS To upgrade Dell EMC Networking Operating System (OS), refer to the Release Notes for the version you want to load on the system. You can download the release notes of your platform at https://www.force10networks.com. Use your login ID to log in to the website. Using HTTP for File Transfers Stating with Release 9.3(0.1), you can use HTTP to copy files or configuration details to a remote server.
PAGE 54
To validate a software image: 1. Download Dell EMC Networking OS software image file from the iSupport page to the local (FTP or TFTP) server. The published hash for that file displays next to the software image file on the iSupport page. 2. Go on to the Dell EMC Networking system and copy the software image to the flash drive, using the copy command. 3. Run the verify {md5 | sha256} [ flash://]img-file sha256 flash://FTOS-SE-9.5.0.0.bin [hash-value] command. For example, verify 4.
PAGE 55
4 Management This chapter describes the different protocols or services used to manage the Dell EMC Networking system.
PAGE 56
● restricting access A user can access all commands at his privilege level and below. Removing a Command from EXEC Mode To remove a command from the list of available commands in EXEC mode for a specific privilege level, use the privilege exec command from CONFIGURATION mode. In the command, specify a level greater than the level given to a user or terminal line, then the first keyword of each command you wish to restrict.
PAGE 57
privilege exec level level configure ● Allow access to INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode. Specify all the keywords in the command. CONFIGURATION mode privilege configure level level {interface | line | route-map | router} {command-keyword ||...|| command-keyword} ● Allow access to a CONFIGURATION, INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode command. CONFIGURATION mode privilege {configure |interface | line | route-map | router} level level {command ||...
PAGE 58
DellEMC(conf)#interface group ? gigabitethernet GigabitEthernet interface IEEE 802.3z tengigabitethernet TenGigabit Ethernet interface vlan VLAN keyword DellEMC(conf)# interface group vlan 1 - 2 , tengigabitethernet 1/1 DellEMC(conf-if-group-vl-1-2,te-1/1)# no shutdown DellEMC(conf-if-group-vl-1-2,te-1/1)# end Applying a Privilege Level to a Username To set the user privilege level, use the following command. ● Configure a privilege level for a user.
PAGE 59
Audit and Security Logs This section describes how to configure, display, and clear audit and security logs. The following is the configuration task list for audit and security logs: ● Enabling Audit and Security Logs ● Displaying Audit and Security Logs ● Clearing Audit Logs Enabling Audit and Security Logs You enable audit and security logs to monitor configuration changes or determine if these changes affect the operation of the system in the network.
PAGE 60
Displaying Audit and Security Logs To display audit logs, use the show logging auditlog command in Exec mode. To view these logs, you must first enable the logging extended command. Only the RBAC system administrator user role can view the audit logs. Only the RBAC security administrator and system administrator user role can view the security logs. If extended logging is disabled, you can only view system events, regardless of RBAC user role. To view security logs, use the show logging command.
PAGE 61
Figure 2. Setting Up a Secure Connection to a Syslog Server Pre-requisites To configure a secure connection from the switch to the syslog server: 1. On the switch, enable the SSH server DellEMC(conf)#ip ssh server enable 2. On the syslog server, create a reverse SSH tunnel from the syslog server to the Dell OS switch, using following syntax: ssh -R :: user@remote_host -nNf In the following example the syslog server IP address is 10.156.166.
PAGE 62
Log Messages in the Internal Buffer All error messages, except those beginning with %BOOTUP (Message), are log in the internal buffer.
PAGE 63
In the previous lines, local7 is the logging facility level and debugging is the severity level. Track Login Activity Dell EMC Networking OS enables you to track the login activity of users and view the successful and unsuccessful login events.
PAGE 64
Unsuccessful login attempt(s) in last 30 day(s): 0 Successful login attempt(s) in last 30 day(s): 1 -----------------------------------------------------------------Example of the show login statistics all command The show login statistics all command displays the successful and failed login details of all users in the last 30 days or the custom defined time period.
PAGE 65
The following is sample output of the show login statistics unsuccessful-attempts time-period days command. DellEMC# show login statistics unsuccessful-attempts time-period 15 There were 0 unsuccessful login attempt(s) for user admin in last 15 day(s). The following is sample output of the show login statistics unsuccessful-attempts user login-id command. DellEMC# show login statistics unsuccessful-attempts user admin There were 3 unsuccessful login attempt(s) for user admin in last 12 day(s).
PAGE 66
During the next authentication attempt, the system does not allow any attempt to login since maximum VTY sessions have reached and hence no clear-line option. NOTE: If the maximum number of VTY lines are more than the concurrent sessions and the same user is attempting to login second time or more, the system displays the Maximum concurrent sessions for the user reached message. You are allowed to clear the existing session and login.
PAGE 67
Changing System Logging Settings You can change the default settings of the system logging by changing the severity level and the storage location. The default is to log all messages up to debug level, that is, all system messages. By changing the severity level in the logging commands, you control the number of system messages logged. To specify the system logging settings, use the following commands. ● Specify the minimum severity level for logging to the logging buffer.
PAGE 68
%CHMGR-5-CARDDETECTED: Line card 0 present %CHMGR-5-CARDDETECTED: Line card 2 present %CHMGR-5-CARDDETECTED: Line card 4 present %CHMGR-5-CARDDETECTED: Line card 5 present %CHMGR-5-CARDDETECTED: Line card 8 present %CHMGR-5-CARDDETECTED: Line card 10 present %CHMGR-5-CARDDETECTED: Line card 12 present %TSM-6-SFM_DISCOVERY: Found SFM 0 %TSM-6-SFM_DISCOVERY: Found SFM 1 %TSM-6-SFM_DISCOVERY: Found SFM 2 %TSM-6-SFM_DISCOVERY: Found SFM 3 %TSM-6-SFM_DISCOVERY: Found SFM 4 %TSM-6-SFM_DISCOVERY: Found SFM 5 %TSM-
PAGE 69
○ uucp (UNIX to UNIX copy protocol) To view nondefault settings, use the show running-config logging command in EXEC mode. DellEMC#show running-config logging ! logging buffered 524288 debugging service timestamps log datetime msec service timestamps debug datetime msec ! logging trap debugging logging facility user logging source-interface Loopback 0 logging 10.10.10.
PAGE 70
○ msec: Enter the keyword msec to include milliseconds in the timestamp. ○ uptime: To view time since last boot. ○ utc: Enter the keyword utc to view timestamp in UTC time that excludes the local time zone. If you do not specify a parameter, Dell EMC Networking OS configures datetime as localtime by default. To view the configuration, use the show running-config logging command in EXEC privilege mode. To disable time stamping on syslog messages, use the no service timestamps [log | debug] command.
PAGE 71
[May 17 10:17:50]: CMD-(CLI):[show logging]by default from console [May 17 10:17:56]: CMD-(CLI):[show command-history]by default from console DellEMC# show logging Syslog logging: enabled Console logging: disabled Monitor logging: level debugging Buffer logging: level debugging, 6 Messages Logged, Size (40960 bytes) Trap logging: level informational Last logging buffer cleared: May 17 15:46:36 May 17 10:17:46 %STKUNIT1-M:CP %SYS-5-CONFIG_I: Configured from console May 17 10:17:40 %STKUNIT1-M:CP %FILEMGR-5-F
PAGE 72
[May 17 15:53:16]: CMD-(CLI):[write memory]by default from console - Repeated 3 times. [May 17 15:53:22]: CMD-(CLI):[show logging]by default from console - Repeated 1 time. [May 17 15:53:36]: CMD-(CLI):[write memory]by default from console - Repeated 5 times.
PAGE 73
ftp-server enable DellEMC#show running ftp ! ftp-server enable ftp-server username nairobi password 0 zanzibar DellEMC# Configuring FTP Server Parameters After you enable the FTP server on the system, you can configure different parameters. To specify the system logging settings, use the following commands. ● Specify the directory for users using FTP to reach the system. CONFIGURATION mode ftp-server topdir dir The default is the internal flash directory.
PAGE 74
Terminal Lines You can access the system remotely and restrict access to the system by creating user profiles. Terminal lines on the system provide different means of accessing the system. The console line (console) connects you through the console port in the route processor modules (RPMs). The virtual terminal lines (VTYs) connect you through Telnet to the system. The auxiliary line (aux) connects secondary devices such as modems.
PAGE 75
DellEMC(config-line-vty)#show c line vty 0 exec-timeout 0 0 access-class testpermit ipv4 access-class testv6deny ipv6 ! Configuring Login Authentication for Terminal Lines You can use any combination of up to six authentication methods to authenticate a user on a terminal line. A combination of authentication methods is called a method list.
PAGE 76
Setting Timeout for EXEC Privilege Mode EXEC timeout is a basic security feature that returns Dell EMC Networking OS to EXEC mode after a period of inactivity on the terminal lines. To set timeout, use the following commands. ● Set the number of minutes and seconds. The default is 10 minutes on the console and 30 minutes on VTY. Disable EXEC time out by setting the timeout period to 0. LINE mode exec-timeout minutes [seconds] ● Return to the default timeout values.
PAGE 77
Lock CONFIGURATION Mode Dell EMC Networking OS allows multiple users to make configurations at the same time. You can lock CONFIGURATION mode so that only one user can be in CONFIGURATION mode at any time (Message 2). You can set two types of lockst: auto and manual. ● Set auto-lock using the configuration mode exclusive auto command from CONFIGURATION mode. When you set auto-lock, every time a user is in CONFIGURATION mode, all other users are denied access.
PAGE 78
NOTE: You must manually enter each CLI command. The system rejects a command if you copy and paste it in the command line. 5. Configure a new password. CONFIGURATION mode enable {secret | password} 6. Save the change in the running configuration to the startup configuration. EXEC Privilege mode copy running-config startup-config Recovering from a Forgotten Enable Password Use the following commands if you forget the enable password. 1. Log onto the system using the console. 2.
PAGE 79
BOOT_USER# boot change default 5. Reboot the chassis. BOOT_USER mode reload Restoring the Factory Default Settings Restoring the factory-default settings deletes the existing NVRAM settings, startup configuration, and all configured settings such as, stacking or fanout. To restore the factory default settings, use the restore factory-defaults stack-unit {stack—unit—number | all} {clear-all | nvram | bootvar} command in EXEC Privilege mode. CAUTION: There is no undo for this command.
PAGE 80
1. Power-cycle the chassis (pull the power cord and reinsert it). 2. Press esc key to abort the boot process (while the system prompts to) You enter BLI immediately, as indicated by the BOOT_USER # prompt. press any key 3. Assign the new location of the Dell EMC Networking OS image to be used when the system reloads.
PAGE 81
Enter the stack-unit keyword and the keyword all to view the reason for the last system reboot of all stack units in the stack. DellEMC#show reset-reason Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 DellEMC# show reset-reason stack-unit 1 Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 Disabling Syslog Messages for SNMP Authentication Failure Events The system generates syslog messages for SNMP authentication events.
PAGE 82
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. A device connected to a port that is enabled with 802.1X is disallowed from sending or receiving packets on the network until its identity is verified (through a username and password, for example). 802.
PAGE 83
● The device attempting to access the network is the supplicant. The supplicant is not allowed to communicate on the network until the authenticator authorizes the port. It can only communicate with the authenticator in response to 802.1X requests. ● The device with which the supplicant communicates is the authenticator. The authenticator is the gate keeper of the network. It translates and forwards requests and responses between the authentication server and the supplicant.
PAGE 84
Figure 5. EAP Port-Authentication EAP over RADIUS 802.1X uses RADIUS to shuttle EAP packets between the authenticator and the authentication server, as defined in RFC 3579. EAP messages are encapsulated in RADIUS packets as a type of attribute in Type, Length, Value (TLV) format. The Type value for EAP messages is 79. Figure 6. EAP Over RADIUS RADIUS Attributes for 802.1X Support Dell EMC Networking systems include the following RADIUS attributes in all 802.
PAGE 85
Configuring 802.1X Configuring 802.1X on a port is a one-step process. For more information, refer to Enabling 802.1X. Related Configuration Tasks ● ● ● ● ● ● Configuring Request Identity Re-Transmissions Forcibly Authorizing or Unauthorizing a Port Re-Authenticating a Port Configuring Timeouts Configuring a Guest VLAN Configuring an Authentication-Fail VLAN Important Points to Remember ● Dell EMC Networking OS supports 802.
PAGE 86
Enabling 802.1X Enable 802.1X globally. Figure 7. 802.1X Enabled 1. Enable 802.1X globally. CONFIGURATION mode dot1x authentication 2. Enter INTERFACE mode on an interface or a range of interfaces. INTERFACE mode interface [range] 3. Enable 802.1X on the supplicant interface only. INTERFACE mode dot1x authentication Verify that 802.1X is enabled globally and at the interface level using the show running-config | find dot1x command from EXEC Privilege mode.
PAGE 87
no ip address dot1x authentication no shutdown ! DellEMC# To view 802.1X configuration information for an interface, use the show dot1x interface command. In the following example, the bold lines show that 802.1X is enabled on all ports unauthorized by default. DellEMC#show dot1x interface TenGigabitEthernet 2/1/ 802.
PAGE 88
● Configure a list of MAC addresses for a dot1x profile. DOT1X PROFILE CONFIG (conf-dot1x-profile) mac mac-address mac-address — Enter the keyword mac and type up to the 48– bit MAC addresses using the nn:nn:nn:nn:nn:nn format. A maximum of 6 MAC addresses are allowed. The following example configures 2 MAC addresses and then displays these addresses.
PAGE 89
Auth PAE State: Backend State: Authenticated Idle Configuring Critical VLAN By default, critical-VLAN is not configured. If authentication fails because of a server which is not reachable, user session is authenticated under critical-VLAN. To configure a critical-VLAN for users or devices when authenticating server is not reachable, use the following command.
PAGE 90
● Configure the amount of time that the authenticator waits before re-transmitting an EAP Request Identity frame. INTERFACE mode dot1x tx-period number The range is from 1 to 65535 (1 year) The default is 30. ● Configure the maximum number of times the authenticator re-transmits a Request Identity frame. INTERFACE mode dot1x max-eap-req number The range is from 1 to 10. The default is 2.
PAGE 91
Forcibly Authorizing or Unauthorizing a Port The 802.1X ports can be placed into any of the three states: ● ForceAuthorized — an authorized state. A device connected to this port in this state is never subjected to the authentication process, but is allowed to communicate on the network. Placing the port in this state is same as disabling 802.1X on the port. ● ForceUnauthorized — an unauthorized state.
PAGE 92
INTERFACE mode dot1x reauth-max number The range is from 1 to 10. The default is 2. The bold lines show that re-authentication is enabled and the new maximum and re-authentication time period. DellEMC(conf-if-Te-1/1)#dot1x reauthentication interval 7200 DellEMC(conf-if-Te-1/1)#dot1x reauth-max 10 DellEMC(conf-if-Te-1/1)#do show dot1x interface TenGigabitEthernet 1/1 802.
PAGE 93
Guest VLAN: Disable Guest VLAN id: NONE Auth-Fail VLAN: Disable Auth-Fail VLAN id: NONE Auth-Fail Max-Attempts: NONE Tx Period: 90 seconds Quiet Period: 120 seconds ReAuth Max: 10 Supplicant Timeout: 15 seconds Server Timeout: 15 seconds Re-Auth Interval: 7200 seconds Max-EAP-Req: 10 Auth Type: Auth PAE State: Backend State: SINGLE_HOST Initialize Initialize Enter the tasks the user should do after finishing this task (optional).
PAGE 94
Figure 8. Dynamic VLAN Assignment 1. Configure 8021.x globally (refer to Enabling 802.1X) along with relevant RADIUS server configurations (refer to the illustration inDynamic VLAN Assignment with Port Authentication). 2. Make the interface a switchport so that it can be assigned to a VLAN. 3. Create the VLAN to which the interface will be assigned. 4. Connect the supplicant to the port configured for 802.1X. 5.
PAGE 95
● If a port is already forwarding on the Guest VLAN when 802.1X is enabled, the port is moved out of the Guest VLAN and the authentication process begins. Configuring a Guest VLAN If the supplicant does not respond within a determined amount of time ([reauth-max + 1] * tx-period, the system assumes that the host does not have 802.1X capability and the port is placed in the Guest VLAN. NOTE: For more information about configuring timeouts, refer to Configuring Timeouts.
PAGE 96
Example of Viewing Configured Authentication 802.
PAGE 97
6 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements.
PAGE 98
The ACL manager does not notify the ACL agent in the following cases: ● The ACL VLAN group is created. ● The ACL VLAN group is deleted and it does not contain VLAN members. ● The ACL is applied or removed from a group and the ACL group does not contain a VLAN member. ● The description of the ACL group is added or removed.
PAGE 99
acl-vlan-group {group name} 2. Add a description to the ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode description description 3. Add VLAN member(s) to an ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode member vlan {VLAN-range} 4. Display all the ACL VLAN groups or display a specific ACL VLAN group, identified by name.
PAGE 100
Viewing CAM Usage View the amount of CAM space available, used, and remaining in each partition (including IPv4Flow and Layer 2 ACL subpartitions) using the show cam-usage command in EXEC Privilege mode. Display Layer 2, Layer 3, ACL, or all CAM usage statistics. EXCE Privilege mode show cam usage [acl | router | switch] The following output shows CAM blocks usage for Layer 2 and Layer 3 ACLs and other processes that use CAM space: Starting from OS 9.11(2.
PAGE 101
| | OUT-V6 ACL | Codes: * - cam usage is above 90%.
PAGE 102
7 Access Control Lists (ACLs) This chapter describes access control lists (ACLs), prefix lists, and route-maps. At their simplest, access control lists (ACLs), prefix lists, and route-maps permit or deny traffic based on MAC and/or IP addresses. This chapter describes implementing IP ACLs, IP prefix lists and route-maps. For MAC ACLS, refer to Layer 2.
PAGE 103
• • • • • • • • • • Assign an IP ACL to an Interface Applying an IP ACL Configure Ingress ACLs Configure Egress ACLs IP Prefix Lists ACL Remarks ACL Resequencing Route Maps Configuring UDF ACL Configuring IP Mirror Access Group IP Access Control Lists (ACLs) In Dell EMC Networking switch/routers, you can create two different types of IP ACLs: standard or extended. A standard ACL filters packets based on the source IP packet.
PAGE 104
CAM Optimization When you enable this command, if a policy map containing classification rules (ACL and/or dscp/ ip-precedence rules) is applied to more than one physical interface on the same port-pipe, only a single copy of the policy is written (only one FP entry is used). When you disable this command, the system behaves as described in this chapter. Test CAM Usage This command applies to both IPv4 and IPv6 CAM profiles, but is best used when verifying QoS optimization for IPv6 ACLs.
PAGE 105
ACL Optimization If an access list contains duplicate entries, Dell EMC Networking OS deletes one entry to conserve CAM space. Standard and extended ACLs take up the same amount of CAM space. A single ACL rule uses two CAM entries to identify whether the access list is a standard or extended ACL.
PAGE 106
Configuration Task List for Route Maps Configure route maps in ROUTE-MAP mode and apply the maps in various commands in ROUTER RIP and ROUTER OSPF modes. The following list includes the configuration tasks for route maps, as described in the following sections.
PAGE 107
level stub-area DellEMC# The following example shows a route map with multiple instances. The show config command displays only the configuration of the current route map instance. To view all instances of a specific route map, use the show route-map command.
PAGE 108
Configuring Match Routes To configure match criterion for a route map, use the following commands. ● Match routes with the same AS-PATH numbers. CONFIG-ROUTE-MAP mode match as-path as-path-name ● Match routes with COMMUNITY list attributes in their path. CONFIG-ROUTE-MAP mode match community community-list-name [exact] ● Match routes whose next hop is a specific interface.
PAGE 109
To create route map instances, use these commands. There is no limit to the number of match commands per route map, but the convention is to keep the number of match filters in a route map low. Set commands do not require a corresponding match command. Configuring Set Conditions To configure a set condition, use the following commands. ● Add an AS-PATH number to the beginning of the AS-PATH. CONFIG-ROUTE-MAP mode set as-path prepend as-number [...
PAGE 110
a routing protocol. Other attributes that can be changed include the metric type (for example, external and internal route types in OSPF) and route tag. Use the redistribute command in OSPF, RIP, ISIS, and BGP to set some of these attributes for routes that are redistributed into those protocols. Route maps add to that redistribution capability by allowing you to match specific routes and set or change more attributes when redistributing those routes.
PAGE 111
IP Fragment Handling Dell EMC Networking OS supports a configurable option to explicitly deny IP fragmented packets, particularly second and subsequent packets. It extends the existing ACL command syntax with the fragments keyword for all Layer 3 rules applicable to all Layer protocols (permit/deny ip/tcp/udp/icmp). ● Both standard and extended ACLs support IP fragments. ● Second and subsequent fragments are allowed because a Layer 4 rule cannot be applied to these fragments.
PAGE 112
Example of Permitting All Packets from a Specified Host DellEMC(conf)#ip access-list extended ABC DellEMC(conf-ext-nacl)#permit tcp host 10.1.1.1 any eq 24 DellEMC(conf-ext-nacl)#deny ip any any fragment DellEMC(conf-ext-nacl) In the following example, the TCP packets that are first fragments or non-fragmented from host 10.1.1.1 with TCP destination port equal to 24 are permitted. Additionally, all TCP non-first fragments from host 10.1.1.1 are permitted.
PAGE 113
seq 20 seq 25 seq 30 seq 35 seq 40 seq 45 seq 50 DellEMC# deny deny deny deny deny deny deny 10.4.0.0 /16 10.5.0.0 /16 10.6.0.0 /16 10.7.0.0 /16 10.8.0.0 /16 10.9.0.0 /16 10.10.0.0 /16 The following example shows how the seq command orders the filters according to the sequence number assigned. In the example, filter 25 was configured before filter 15, but the show config command displays the filters in the correct order. DellEMC(config-std-nacl)#seq 25 deny ip host 10.5.0.
PAGE 114
seq 50 permit tcp 10.8.0.0 /16 10.50.188.118 /31 eq 49 monitor 349 seq 55 permit udp 10.15.1.0 /24 10.50.188.118 /31 range 1812 1813 To delete a filter, enter the show config command in IP ACCESS LIST mode and locate the sequence number of the filter you want to delete. Then use the no seq sequence-number command in IP ACCESS LIST mode.
PAGE 115
seq sequence-number {deny | permit} icmp {source mask | any | host ip-address} [count [byte]] [order] [monitor [session-id]] [fragments] The ICMP packets cannot be filtered using mirroring ACL.
PAGE 116
Configure Filters, TCP Packets To create a filter for TCP packets with a specified sequence number, use the following commands. 1. Create an extended IP ACL and assign it a unique name. CONFIGURATION mode ip access-list extended access-list-name 2. Configure an extended IP ACL filter for TCP packets.
PAGE 117
{deny | permit} udp {source mask | any | host ip-address}} [count [byte]] [order] [monitor [session-id]] [fragments] When you use the log keyword, the CP logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The following example shows an extended IP ACL in which the sequence numbers were assigned by the software.
PAGE 118
The same ACL may be applied to different interfaces and that changes its functionality. For example, you can take ACL “ABCD” and apply it using the in keyword and it becomes an ingress access list. If you apply the same ACL using the out keyword, it becomes an egress access list. If you apply the same ACL to the Loopback interface, it becomes a Loopback access list. Applying an IP ACL To apply an IP ACL (standard or extended) to a physical or port channel interface, use the following commands. 1.
PAGE 119
Configure Ingress ACLs Ingress ACLs are applied to interfaces and to traffic entering the system. These system-wide ACLs eliminate the need to apply ACLs onto each interface and achieves the same results. By localizing target traffic, it is a simpler implementation. To create an ingress ACL, use the ip access-group command in EXEC Privilege mode. The example shows applying the ACL, rules to the newly created access group, and viewing the access list.
PAGE 120
DellEMC(config-ext-nacl)#permit tcp any any DellEMC(config-ext-nacl)#deny icmp any any DellEMC(config-ext-nacl)#permit 1.1.1.2 DellEMC(config-ext-nacl)#end DellEMC#show ip accounting access-list ! Extended Ingress IP access list abcd on tengigabitethernet 0/0 seq 5 permit tcp any any seq 10 deny icmp any any seq 15 permit 1.1.1.
PAGE 121
The following examples show permit or deny filters for specific routes using the le and ge parameters, where x.x.x.x/x represents a route prefix: ● ● ● ● To To To To deny only /8 prefixes, enter deny x.x.x.x/x ge 8 le 8. permit routes with the mask greater than /8 but less than /12, enter permit x.x.x.x/x ge 8. deny routes with a mask less than /24, enter deny x.x.x.x/x le 24. permit routes with a mask greater than /20, enter permit x.x.x.x/x ge 20.
PAGE 122
The following example shows how the seq command orders the filters according to the sequence number assigned. In the example, filter 20 was configured before filter 15 and 12, but the show config command displays the filters in the correct order. DellEMC(conf-nprefixl)#seq 20 permit 0.0.0.0/0 le 32 DellEMC(conf-nprefixl)#seq 12 deny 134.23.0.0 /16 DellEMC(conf-nprefixl)#seq 15 deny 120.23.14.0 /8 le 16 DellEMC(conf-nprefixl)#show config ! ip prefix-list juba seq 12 deny 134.23.0.0/16 seq 15 deny 120.0.0.
PAGE 123
EXEC Privilege mode show ip prefix-list summary [prefix-name] The following example shows the show ip prefix-list detail command. DellEMC>show ip prefix detail Prefix-list with the last deletion/insertion: filter_ospf ip prefix-list filter_in: count: 3, range entries: 3, sequences: 5 - 10 seq 5 deny 1.102.0.0/16 le 32 (hit count: 0) seq 6 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 10 permit 0.0.0.0/0 le 32 (hit count: 0) ip prefix-list filter_ospf: count: 4, range entries: 1, sequences: 5 - 10 seq 5 deny 100.
PAGE 124
Applying a Filter to a Prefix List (OSPF) To apply a filter to routes in open shortest path first (OSPF), use the following commands. ● Enter OSPF mode. CONFIGURATION mode router ospf ● Apply a configured prefix list to incoming routes. You can specify an interface. If you enter the name of a non-existent prefix list, all routes are forwarded. CONFIG-ROUTER-OSPF mode distribute-list prefix-list-name in [interface] ● Apply a configured prefix list to incoming routes.
PAGE 125
The remark number is optional. The following example shows how to write a remark for an ACL rule: Dell(config-ext-nacl)#ip access-list extended test Dell(config-ext-nacl)# remark permit any ip Dell(config-ext-nacl)# seq 10 permit ip any any Dell(config-ext-nacl)#sh config ! ip access-list extended test remark 10 permit any ip seq 10 permit ip any any Deleting a Remark To delete a remark, follow this procedure: A standard IP ACL uses the source IP address as its match criterion.
PAGE 126
Table 7. ACL Resequencing (continued) Rules Resquencing seq 7 permit any host 1.1.1.3 seq 10 permit any host 1.1.1.4 Rules After Resequencing: seq 5 permit any host 1.1.1.1 seq 10 permit any host 1.1.1.2 seq 15 permit any host 1.1.1.3 seq 20 permit any host 1.1.1.4 Resequencing an ACL or Prefix List Resequencing is available for IPv4 and IPv6 ACLs, prefix lists, and MAC ACLs. To resequence an ACL or prefix list, use the following commands.
PAGE 127
ip access-list extended test remark 4 XYZ remark 5 this remark corresponds to permit any host 1.1.1.1 seq 5 permit ip any host 1.1.1.1 remark 9 ABC remark 10 this remark corresponds to permit ip any host 1.1.1.2 seq 10 permit ip any host 1.1.1.2 seq 15 permit ip any host 1.1.1.3 seq 20 permit ip any host 1.1.1.4 DellEMC# end DellEMC# resequence access-list ipv4 test 2 2 DellEMC# show running-config acl ! ip access-list extended test remark 2 XYZ remark 4 this remark corresponds to permit any host 1.1.1.
PAGE 128
EXEC Privilege mode show cam-acl DellEMC#show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 2 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 2 FcoeAcl : 4 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 2 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 2 FcoeAcl :
PAGE 129
key innerL3header udf-id 6 packetbase innerL3Header offset 0 length 2 DellEMC(conf-udf-tcam)# 7. Configure the match criteria for the packet type in which UDF offset bytes are parsed. CONFIGURATION-UDF TCAM mode match l2ethertype ipv4 ipprotocol value vlantag tagStatus DellEMC(conf-udf-tcam)#match l2ethertype ipv4 ipprotocol 4 vlantag any 8. View the UDF TCAM configuration.
PAGE 130
cam-acl {default | l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number [vman-qos | vman-qos—dual— number | vman-qos—dual—fp number] ipv4pbr number} ecfmacl number [nlbclusteraclnumber]fcoeacl number iscsioptacl number ipv4udfmirracl number | ipv4mirracl number} 2. Create a monitor session. CONFIGURATION mode monitor session session-ID [type { rpm | erpm [set ip dscp dscp_value | set ip ttl ttl_value]}] [drop] Dell(conf)#monitor session 65535 type erpm 3.
PAGE 131
8 Bidirectional Forwarding Detection (BFD) BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no routing protocol is used. BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake.
PAGE 132
BFD Packet Format Control packets are encapsulated in user datagram protocol (UDP) packets. The following illustration shows the complete encapsulation of a BFD control packet inside an IPv4 packet. Figure 9. BFD in IPv4 Packet Format Field Description Diagnostic Code The reason that the last session failed. State The current local session state. Refer to BFD Sessions. Flag A bit that indicates packet function.
PAGE 133
Field Description Your Discriminator A random number generated by the remote system to identify the session. Discriminator values are necessary to identify the session to which a control packet belongs because there can be many sessions running on a single interface. Desired Min TX Interval The minimum rate at which the local system would like to send control packets to the remote system.
PAGE 134
State Description Init The local system is communicating. Up Both systems are exchanging control packets. The session is declared down if: ● A control packet is not received within the detection time. ● Sufficient echo packets are lost. ● Demand mode is active and a control packet is not received in response to a poll packet. BFD Three-Way Handshake A three-way handshake must take place between the systems that participate in the BFD session.
PAGE 135
Session State Changes The following illustration shows how the session state on a system changes based on the status notification it receives from the remote system. For example, if a session on a system is down and it receives a Down status notification from the remote system, the session state on the local system changes to Init. Figure 11.
PAGE 136
● ● ● ● ● Configure BFD for OSPFv3 Configure BFD for IS-IS Configure BFD for BGP Configure BFD for VRRP Configuring Protocol Liveness Configure BFD for Physical Ports Configuring BFD for physical ports is supported on the C-Series and E-Series platforms only. BFD on physical ports is useful when you do not enable the routing protocol. Without BFD, if the remote system fails, the local system does not remove the connected route until the first failed attempt to send a packet.
PAGE 137
Remote Addr: 2.2.2.
PAGE 138
● Disabling BFD for Static Routes Establishing Sessions for Static Routes for Default VRF Sessions are established for all neighbors that are the next hop of a static route on the default VRF. Figure 12. Establishing Sessions for Static Routes To establish a BFD session, use the following command. ● Establish BFD sessions for all neighbors that are the next hop of a static route.
PAGE 139
Example Configuration and Verification The following example contains static routes for both default and nondefault VRFs. Dell#sh run | grep bfd bfd enable ip route bfd prefix-list p4_le ip route bfd vrf vrf1 ip route bfd vrf vrf2 ip route bfd vrf vrf1 prefix-list p4_le The following example shows that sessions are created for static routes for the default VRF.
PAGE 140
Prefix lists are used in route maps and route filtering operations. You can use prefix lists as an alternative to existing access lists (ACLs). A prefix is a portion of the IP address. Prefix lists constitute any number of bits in an IP address starting from the far left bit of the far left octet. By specifying the exactly number of bits in an IP address that belong to a prefix list, the prefix list can be used to aggregate addresses and perform some functions; for example, redistribution.
PAGE 141
no ip route bfd [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] Configure BFD for IPv6 Static Routes BFD offers systems a link state detection mechanism for static routes. With BFD, systems are notified to remove static routes from the routing table as soon as the link state change occurs, rather than waiting until packets fail to reach their next hop. Configuring BFD for IPv6 static routes is a three-step process: 1. Enable BFD globally. 2.
PAGE 142
ipv6 route bfd vrf vrf-name [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] Example Configuration and Verification The following example contains static routes for both default and nondefault VRFs. Dell#show run | grep bfd bfd enable ipv6 route bfd prefix-list p6_le ipv6 route bfd vrf vrf1 ipv6 route bfd vrf vrf2 ipv6 route bfd vrf vrf1 prefix-list p6_le The following example shows that sessions are created for static routes for the default VRF.
PAGE 143
Changing IPv6 Static Route Session Parameters BFD sessions are configured with default intervals and a default role. The parameters you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all static routes. If you change a parameter, the change affects all sessions for static routes. To change parameters for static route sessions, use the following command . ● Change parameters for all static route sessions.
PAGE 144
Establishing Sessions with OSPF Neighbors for the Default VRF BFD sessions can be established with all OSPF neighbors at once or sessions can be established with all neighbors out of a specific interface. Sessions are only established when the OSPF adjacency is in the Full state. Figure 13. Establishing Sessions with OSPF Neighbors To establish BFD with all OSPF neighbors or with OSPF neighbors on a single interface, use the following commands. ● Enable BFD globally.
PAGE 145
The bold line shows the OSPF BFD sessions. R2(conf-router_ospf)#bfd all-neighbors R2(conf-router_ospf)#do show bfd neighbors * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients * 2.2.2.2 2.2.2.1 Te 2/1 Up 100 100 3 O * 2.2.3.1 2.2.3.2 Te 2/2 Up 100 100 3 O Establishing Sessions with OSPF Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, follow this procedure: ● Enable BFD globally.
PAGE 146
* * * * * 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 192.168.122.135 192.168.122.136 192.168.122.137 192.168.122.138 192.168.122.139 Te Te Te Te Te 1/38 1/42 1/43 1/38 1/42 Up Up Up Up Up 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 3 3 3 3 3 VT VT VT VT VT DellEMC# show bfd neighbors detail Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.
PAGE 147
ROUTER-OSPF mode no bfd all-neighbors ● Disable BFD sessions with all OSPF neighbors on an interface. INTERFACE mode ip ospf bfd all-neighbors disable Configure BFD for OSPFv3 BFD for OSPFv3 provides support for IPV6. Configuring BFD for OSPFv3 is a two-step process: 1. Enable BFD globally. 2. Establish sessions with OSPFv3 neighbors.
PAGE 148
O3 DellEMC# Establishing BFD Sessions with OSPFv3 Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, use the following procedure: ● Enable BFD globally. CONFIGURATION mode bfd enable ● Establish sessions with all OSPFv3 neighbors in a specific VRF. ROUTER-OSPFv3 mode bfd all-neighbors ● Establish sessions with the OSPFv3 neighbors on a single interface in a specific VRF.
PAGE 149
3 511 O3 * fe80::2a0:c9ff:fe00:2 3 511 O3 fe80::3617:98ff:fe34:12 Vl 101 Up 150 150 * fe80::2a0:c9ff:fe00:2 3 511 O3 fe80::3617:98ff:fe34:12 Vl 102 Up 150 150 * fe80::2a0:c9ff:fe00:2 3 511 O3 DellEMC# fe80::3617:98ff:fe34:12 Vl 103 Up 150 150 Changing OSPFv3 Session Parameters Configure BFD sessions with default intervals and a default role. The parameters that you can configure are: desired tx interval, required min rx interval, detection multiplier, and system role.
PAGE 150
Related Configuration Tasks ● Changing IS-IS Session Parameters ● Disabling BFD for IS-IS Establishing Sessions with IS-IS Neighbors BFD sessions can be established for all IS-IS neighbors at once or sessions can be established for all neighbors out of a specific interface. Figure 14. Establishing Sessions with IS-IS Neighbors To establish BFD with all IS-IS neighbors or with IS-IS neighbors on a single interface, use the following commands. ● Establish sessions with all IS-IS neighbors.
PAGE 151
C I O R - CLI - ISIS - OSPF - Static Route (RTM) LocalAddr * 2.2.2.2 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 Te 2/1 Up 100 100 3 I Changing IS-IS Session Parameters BFD sessions are configured with default intervals and a default role. The parameters that you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all IS-IS sessions or all IS-IS sessions out of an interface.
PAGE 152
Figure 15. Establishing Sessions with BGP Neighbors The sample configuration shows alternative ways to establish a BFD session with a BGP neighbor: ● By establishing BFD sessions with all neighbors discovered by BGP (the bfd all-neighbors command). ● By establishing a BFD session with a specified BGP neighbor (the neighbor {ip-address | peer-group-name} bfd command) BFD packets originating from a router are assigned to the highest priority egress queue to minimize transmission delays.
PAGE 153
CONFIGURATION mode bfd enable 2. Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3. Add a BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group name} remote-as as-number 4. Enable the BGP neighbor. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group-name} no shutdown 5. Add a BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP mode neighbor {ipv6-address | peer-group name} remote-as as-number 6.
PAGE 154
bfd enable 2. Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3. Specify the address family as IPv4. CONFIG-ROUTERBGP mode address-family ipv4 vrf vrf-name 4. Add an IPv4 BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP_ADDRESSFAMILY mode neighbor {ip-address | peer-group name} remote-as as-number 5. Enable the BGP neighbor. CONFIG-ROUTERBGP_ADDRESSFAMILY mode neighbor {ip-address | peer-group-name} no shutdown 6.
PAGE 155
exit-address-family DellEMC(conf-router_bgp)# Disabling BFD for BGP You can disable BFD for BGP. To disable a BFD for BGP session with a specified neighbor, use the first command. To remove the disabled state of a BFD for BGP session with a specified neighbor, use the second command. The BGP link with the neighbor returns to normal operation and uses the BFD session parameters globally configured with the bfd all-neighbors command or configured for the peer group to which the neighbor belongs.
PAGE 156
C I O R M V - CLI ISIS OSPF Static Route (RTM) MPLS VRRP LocalAddr * 1.1.1.3 * 2.2.2.3 * 3.3.3.3 RemoteAddr 1.1.1.2 2.2.2.2 3.3.3.2 Interface Te 6/1 Te 6/2 Te 6/3 State Up Up Up Rx-int 200 200 200 Tx-int 200 200 200 Mult 3 3 3 Clients B B B The following example shows viewing BFD neighbors with full detail. The bold lines show the BFD session parameters: TX (packet transmission), RX (packet reception), and multiplier (maximum number of missed packets).
PAGE 157
The bold line shows the message displayed when you enable BFD for BGP connections. R2# show ip bgp summary BGP router identifier 10.0.0.1, local AS number 2 BGP table version is 0, main routing table version 0 BFD is enabled, Interval 200 Min_rx 200 Multiplier 3 Role Active 3 neighbor(s) using 24168 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 1.1.1.2 2.2.2.2 3.3.3.
PAGE 158
... R2# show ip bgp neighbors 2.2.2.4 BGP neighbor is 2.2.2.4, remote AS 1, external link Member of peer-group pg1 for session parameters BGP version 4, remote router ID 12.0.0.4 BGP state ESTABLISHED, in this state for 00:05:33 ... Neighbor is using BGP peer-group mode BFD configuration Peer active in peer-group outbound optimization ... Configure BFD for VRRP When using BFD with VRRP, the VRRP protocol registers with the BFD manager on the route processor module (RPM).
PAGE 159
To establish sessions with all VRRP neighbors, use the following command. ● Establish sessions with all VRRP neighbors. INTERFACE mode vrrp bfd all-neighbors Establishing VRRP Sessions on VRRP Neighbors The master router does not care about the state of the backup router, so it does not participate in any VRRP BFD sessions. VRRP BFD sessions on the backup router cannot change to the UP state. Configure the master router to establish an individual VRRP session the backup router.
PAGE 160
vrrp bfd all-neighbors interval milliseconds min_rx milliseconds multiplier value role [active | passive] ● Change parameters for a particular VRRP session. INTERFACE mode vrrp bfd neighbor ip-address interval milliseconds min_rx milliseconds multiplier value role [active | passive] To view session parameters, use the show bfd neighbors detail command. Disabling BFD for VRRP If you disable any or all VRRP sessions, the sessions are torn down.
PAGE 161
9 Border Gateway Protocol (BGP) Border Gateway Protocol (BGP) is an interdomain routing protocol that manages routing between edge routers. BGP uses an algorithm to exchange routing information between switches enabled with BGP. BGP determines a path to reach a particular destination using certain attributes while avoiding routing loops. BGP selects a single path as the best path to a destination network or host. You can also influence BGP to select different path by altering some of the BGP attributes.
PAGE 162
The devices within an AS (AS1 or AS2, as seen in the following illustration) exchange routing information using Internal BGP (IBGP), whereas the devices in different AS communicate using External BGP (EBGP). IBGP provides routers inside the AS with the knowledge to reach routers external to the AS. EBGP routers exchange information with other EBGP routers as well as IBGP routers to maintain connectivity and accessibility. Figure 17.
PAGE 163
Figure 18. BGP Routers in Full Mesh The number of BGP speakers each BGP peer must maintain increases exponentially. Network management quickly becomes impossible. AS4 Number Representation Dell EMC Networking OS supports multiple representations of 4-byte AS numbers: asplain, asdot+, and asdot. NOTE: The ASDOT and ASDOT+ representations are supported only with the 4-Byte AS numbers feature. If 4-Byte AS numbers are not implemented, only ASPLAIN representation is supported.
PAGE 164
● All AS numbers between 0 and 65535 are represented as a decimal number, when entered in the CLI and when displayed in the show commands outputs. ● AS Numbers larger than 65535 is represented using ASDOT notation as .. For example: AS 65546 is represented as 1.10. ASDOT representation combines the ASPLAIN and ASDOT+ representations.
PAGE 165
DellEMC(conf-router_bgp)#do sho ip bgp BGP table version is 28093, local router ID is 172.30.1.57 AS4 SUPPORT DISABLED DellEMC(conf-router_bgp)#no bgp four-octet-as-support DellEMC(conf-router_bgp)#sho conf ! router bgp 100 neighbor 172.30.1.250 local-as 65057 DellEMC(conf-router_bgp)#do show ip bgp BGP table version is 28093, local router ID is 172.30.1.57 Four-Byte AS Numbers You can use the 4-Byte (32-bit) format when configuring autonomous system numbers (ASNs).
PAGE 166
State Description Idle BGP initializes all resources, refuses all inbound BGP connection attempts, and initiates a TCP connection to the peer. Connect In this state the router waits for the TCP connection to complete, transitioning to the OpenSent state if successful. If that transition is not successful, BGP resets the ConnectRetry timer and transitions to the Active state when the timer expires. Active The router resets the ConnectRetry timer to zero and returns to the Connect state.
PAGE 167
Best Path Selection Criteria Paths for active routes are grouped in ascending order according to their neighboring external AS number (BGP best path selection is deterministic by default, which means the bgp non-deterministic-med command is NOT applied). The best path in each group is selected based on specific criteria. Only one “best path” is selected at a time. If any of the criteria results in more than one path, BGP moves on to the next option in the list.
PAGE 168
6. Prefer the path with the lowest multi-exit discriminator (MED) attribute. The following criteria apply: a. This comparison is only done if the first (neighboring) AS is the same in the two paths; the MEDs are compared only if the first AS in the AS_SEQUENCE is the same for both paths. b. If you entered the bgp always-compare-med command, MEDs are compared for all paths. c. Paths with no MED are treated as “worst” and assigned a MED of 4294967295. 7.
PAGE 169
Figure 20. BGP Local Preference Multi-Exit Discriminators (MEDs) If two ASs connect in more than one place, a multi-exit discriminator (MED) can be used to assign a preference to a preferred path. MED is one of the criteria used to determine the best path, so keep in mind that other criteria may impact selection, as shown in the illustration in Best Path Selection Criteria. One AS assigns the MED a value and the other AS uses that value to decide the preferred path.
PAGE 170
Figure 21. Multi-Exit Discriminators NOTE: Configuring the set metric-type internal command in a route-map advertises the IGP cost as MED to outbound EBGP peers when redistributing routes. The configured set metric value overwrites the default IGP cost. If the outbound route-map uses MED, it overwrites IGP MED. Origin The origin indicates the origin of the prefix, or how the prefix came into BGP. There are three origin codes: IGP, EGP, INCOMPLETE.
PAGE 171
The AS path is shown in the following example. The origin attribute is shown following the AS path information (shown in bold).
PAGE 172
unicast and multicast BGP database to form a routing table for unicast and multicast. You can configure BGP peers that exchange both unicast and multicast Network Layer Reachability Information (NLRI) in which MBGP routes is redistributed into BGP. The default is IPv4 unicast. IPv4 and IPv6 address family The IPv4 address family configuration in Dell EMC Networking OS is used for identifying routing sessions for protocols that use IPv4 address. You can specify multicast within the IPv4 address family.
PAGE 173
BGP global configuration default values By default, BGP is disabled. The following table displays the default values for BGP on Dell EMC Networking OS. Table 8. BGP Default Values Item Default BGP Neighbor Adjacency changes All BGP neighbor changes are logged.
PAGE 174
● If the redistribute command has metric configured (route-map set metric or redistribute route-type metric) and the BGP peer outbound route-map has metric-type internal configured, BGP advertises the metric configured in the redistribute command as MED. ● If BGP peer outbound route-map has metric configured, all other metrics are overwritten by this configuration. NOTE: When redistributing static, connected, or OSPF routes, there is no metric option.
PAGE 175
Figure 22. Before and After AS Number Migration with Local-AS Enabled When you complete your migration, and you have reconfigured your network with the new information, disable this feature. If you use the “no prepend” option, the Local-AS does not prepend to the updates received from the eBGP peer. If you do not select “no prepend” (the default), the Local-AS is added to the first AS segment in the AS-PATH.
PAGE 176
● Configure inbound BGP soft-reconfiguration on a peer for f10BgpM2PrefixInPrefixesRejected to display the number of prefixes filtered due to a policy. If you do enable BGP soft-reconfig, the denied prefixes are not accounted for. ● F10BgpM2AdjRibsOutRoute stores the pointer to the NLRI in the peer's Adj-Rib-Out. ● PA Index (f10BgpM2PathAttrIndex field in various tables) is used to retrieve specific attributes from the PA table.
PAGE 177
Basic BGP configuration tasks The following sections describe how to configure a basic BGP network and the basic configuration tasks that are required for the BGP to be up and running.
PAGE 178
neighbor {ip-address | ipv6-address| peer-group name} remote-as as-number ● ip-address: IPv4 address of the neighbor ● ipv6-address: IPv6 address of the neighbor ● peer-group name: Name of the peer group. It can contain 16 characters. ● as-number: Autonomous number NOTE: Neighbors that are defined using the neighbor remote-as command in the CONFIGURATION-ROUTERBGP mode exchange IPv4 unicast address prefixes only. 3. Enable the BGP neighbor.
PAGE 179
The third line of the show ip bgp neighbors output contains the BGP State. If anything other than ESTABLISHED is listed, the neighbor is not exchanging information and routes. For more information about using the show ip bgp neighbors command, refer to the Dell EMC Networking OS Command Line Interface Reference Guide. The following example shows the show ip bgp neighbors command output. DellEMC#show ip bgp neighbors BGP neighbor is 20.20.20.1, remote AS 20, external link BGP remote router ID 1.1.1.
PAGE 180
1 neighbor(s) using 40960 bytes of memory Neighbor 20.20.20.1 AS 200 MsgRcvd 0 MsgSent 0 TblVer 0 InQ 0 OutQ Up/Down State/Pfx 0 00:00:00 0 Changing a BGP router ID BGP uses the configured router ID to identify the devices in the network. By default, the router ID is the highest IP address of the Loopback interface. If no Loopback interfaces are configured, the highest IP address of a physical interface on the router is used as the BGP router ID.
PAGE 181
CONFIG-ROUTER-BGP mode bgp asnotation asplain NOTE: ASPLAIN is the default method Dell EMC Networking OS uses and does not appear in the configuration display. ● Enable ASDOT AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asdot ● Enable ASDOT+ AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asdot+ The following example shows the bgp asnotation asplain command output.
PAGE 182
● Enter the router configuration mode and the AS number. CONFIG mode router bgp as-number ● Add the IP address of the neighbor for the specified autonomous system. CONFIG-ROUTER-BGP mode neighbor {ip-address | ipv6–address | peer-group-name} remote-as as-number ● Enable the neighbor. CONFIG-ROUTERBGP mode neighbor ip-address | ipv6-address | peer-group-name no shutdown ● Specify the IPv4 address family configuration.
PAGE 183
To support your own IP addresses, interfaces, names, and so on, you can copy and paste from these examples to your CLI. Be sure that you make the necessary changes. Example-Configuring BGP routing between peers Example of enabling BGP in Router A Following is an example to enable BGP configuration in the router A. RouterA# configure terminal RouterA(conf)# router bgp 40000 RouterA(conf-router_bgp)# bgp router-id 10.1.1.99 RouterA(conf-router_bgp)# timers bgp 80 130 RouterA(conf-router_bgp)# neighbor 192.
PAGE 184
Configuration rules in a peer group: ● You must create a peer group first before adding the neighbors in the peer group. ● If you remove any configuration parameters from a peer group, it will apply to all the neighbors configured under that peer group. ● If you have not configured a parameter for an individual neighbor in the peer group, the neighbor uses the value configured in the peer group. ● If you reset any parameter for an individual neighbor, it will override the value set in the peer group.
PAGE 185
To add an external BGP (EBGP) neighbor, configure the as-number parameter with a number different from the BGP asnumber configured in the router bgp as-number command. To add an internal BGP (IBGP) neighbor, configure the as-number parameter with the same BGP as-number configured in the router bgp as-number command. After you create a peer group, you can use any of the commands beginning with the keyword neighbor to configure that peer group.
PAGE 186
Number of peers in this group 1 Peer-group members (* - outbound optimized): 2001::1 Example-Configuring BGP peer groups The following example configurations show how to enable BGP and set up some peer groups. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations. To support your own IP addresses, interfaces, names, and so on, you can copy and paste from these examples to your CLI. Be sure that you make the necessary changes.
PAGE 187
ip address 10.0.1.21/24 no shutdown R1(conf-if-gi-1/21)#int gi 1/31 R1(conf-if-gi-1/31)#ip address 10.0.3.31/24 R1(conf-if-gi-1/31)#no shutdown R1(conf-if-gi-1/31)#show config ! interface GigabitEthernet 1/31 ip address 10.0.3.31/24 no shutdown R1(conf-if-gi-1/31)#exit R1(conf)#ip route 192.168.128.2/32 10.0.1.22 R1(conf)#router bgp 99 R1(conf-router_bgp)#neighbor 192.168.128.2 remote 99 R1(conf-router_bgp)#neighbor 192.168.128.2 no shut R1(conf-router_bgp)#neighbor 192.168.128.
PAGE 188
Example of Enabling BGP (Router 3) R3#conf R3(conf)#int te 3/11 R3(conf-if-te-3/11)#ip address 10.0.3.33/24 R3(conf-if-te-3/11)#no shutdown R3(conf-if-te-3/11)#show config ! interface TengigabitEthernet 3/11 ip address 10.0.3.33/24 no shutdown R3(conf-if-te-3/11)#int te 3/21 R3(conf-if-te-3/21)#ip address 10.0.2.3/24 R3(conf-if-te-3/21)#no shutdown R3(conf-if-te-3/21)#show config ! interface TengigabitEthernet 3/21 ip address 10.0.2.
PAGE 189
2 BGP AS-PATH entrie(s) using 74 bytes of memory 2 neighbor(s) using 8672 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ 192.168.128.2 99 23 24 0 0 OutQ Up/Down State/Pfx 0 00:06:11 0 Example of Enabling Peer Groups (Router 2) R2#conf R2(conf)#router bgp 99 R2(conf-router_bgp)# neighbor CCC peer-group R2(conf-router_bgp)# neighbor CC no shutdown R2(conf-router_bgp)# neighbor BBB peer-group R2(conf-router_bgp)# neighbor BBB no shutdown R2(conf-router_bgp)# neighbor 192.168.128.
PAGE 190
192.168.128.1 192.168.128.2 99 99 93 122 99 120 1 1 0 0 (0) (0) 00:00:15 1 00:00:11 1 Advanced BGP configuration tasks The following sections describe how to configure the advanced (optional) BGP configuration tasks. Route-refresh and Soft-reconfiguration BGP soft-reconfiguration allows for faster and easier route changing. Changing routing policies typically requires a reset of BGP sessions (the TCP connection) for the policies to take effect.
PAGE 191
DellEMC(conf-router_bgp)# neighbor 10.108.1.1 soft-reconfiguration inbound DellEMC(conf-router_bgp)# exit Route-refresh This section explains how the soft-reconfiguration and route-refresh works. Soft-reconfiguration has to be configured explicitly for a neighbor unlike route refresh, which is automatically negotiated between BGP peers when establishing a peer session.
PAGE 192
IPv4 and IPv6 route-refresh updates are sent. Following is an example configuration in which IPv6 prefixes is enabled for a IPv6 neighbor and the corresponding route-refresh message: DellEMC(conf-router_bgp)# show config ! router bgp 100 redistribute connected neighbor 20.1.1.2 remote-as 200 neighbor 20.1.1.
PAGE 193
aggregate-address ip-address mask [advertise-map map-name] [as-set] [attribute-map mapname] [summary-only] [suppress-map map-name] ○ as-set- Specify that the advertised path of this route is an AS_SET. ○ summary-only-Create aggregate route and suppress advertisements of specific routes to all neighbors. ○ suppress-map map-name-Create aggregate route by suppressing the advertisements of specific routes. ○ advertise-map map-name-Create aggregate route by advertising specific routes.
PAGE 194
The suppress-map keyword creates the aggregate route but suppress the advertisement of specified routes. The routes that are suppressed are not advertised to the neighbors. You can use match clause of route maps to selectively suppress the specific route from the aggregate routes. Following is the sample configuration to suppress the advertisement of specific aggregate routes. DellEMC# configure terminal DellEMC(conf)# router bgp 100 DellEMC(conf-router_bgp)# aggregate-address 10.1.1.
PAGE 195
Regular Expression Definition _ (underscore) Matches a ^, a $, a comma, a space, or a {, or a }. Placed on either side of a string to specify a literal and disallow substring matching. You can precede or follow numerals enclosed by underscores by any of the characters listed. | (pipe) Matches characters on either side of the metacharacter; logical OR. As seen in the following example, the expressions are displayed when using the show commands.
PAGE 196
NOTE: You can create inbound and outbound policies. Each of the commands used for filtering has in and out parameters that you must apply. In Dell EMC Networking OS, the order of preference varies depending on whether the attributes are applied for inbound updates or outbound updates.
PAGE 197
● If none of the routes match any of the filters in the prefix list, the route is denied. This action is called an implicit deny. (If you want to forward all routes that do not match the prefix list criteria, you must configure a prefix list filter to permit all routes. For example, you could have the following filter as the last filter in your prefix list permit 0.0.0.0/0 le 32). ● After a route matches a filter, the filter’s action is applied. No additional filters are applied to the route.
PAGE 198
To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. To view a route map configuration, use the show route-map command in EXEC Privilege mode. Filtering on an AS-Path Attribute You can use the BGP attribute, AS_PATH, to manipulate routing policies. The AS_PATH attribute contains a sequence of AS numbers representing the route’s path. As the route traverses an AS, the ASN is prepended to the route.
PAGE 199
20 0 --More-- 64801 i Filtering Routes with Community Lists To use an IP community list or IP extended community list to filter routes, you must apply a match community filter to a route map and then apply that route map to a BGP neighbor or peer group. 1. Enter the ROUTE-MAP mode and assign a name to a route map. CONFIGURATION mode route-map map-name [permit | deny] [sequence-number] 2. Configure a match filter for all routes meeting the criteria in the IP community or IP extended community list.
PAGE 200
The BGP fast fall-over feature is configured on a per-neighbor or peer-group basis and is disabled by default. To enable the BGP fast fall-over feature, use the following command. ● Enable BGP fast fall-over. CONFIG-ROUTER-BGP mode neighbor {ip-address | ipv6-address | peer-group-name} fall-over To disable fast fall-over, use the [no] neighbor [ip-address | ipv6-address | peer-group] fall-over command in CONFIGURATION ROUTER BGP mode.
PAGE 201
To verify that fast fall-over is enabled on a peer-group, use the show ip bgp peer-group command (shown in bold). DellEMC#show ip bgp peer-group Peer-group test fall-over enabled BGP version 4 Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP neighbor is test Number of peers in this group 1 Peer-group members (* - outbound optimized): 10.10.10.
PAGE 202
Enabling Graceful Restart Use this feature to lessen the negative effects of a BGP restart. Dell EMC Networking OS advertises support for this feature to BGP neighbors through a capability advertisement. You can enable graceful restart by router and/or by peer or peer group. NOTE: By default, BGP graceful restart is disabled. The default role for BGP is as a receiving or restarting peer.
PAGE 203
Redistributing Routes In addition to filtering routes, you can add routes from other routing instances or protocols to the BGP process. You can configure the device to redistribute ISIS, OSPF, static, or directly connected routes into BGP process using the redistribute command. To add routes from other routing instances or protocols, use any of the following commands in ROUTER BGP mode. ● Include directly connected or user-configured (static) routes into BGP.
PAGE 204
To allow multiple paths sent to peers, use the following commands. 1. Allow the advertisement of multiple paths (send, receive or both). CONFIG-ROUTER-BGP or CONFIG-ROUTER-BGP-AF mode bgp add-path [both | enable | receive | send] path-count Configure the following parameters: ● ● ● ● ● both: Indicate that the system sends and accepts multiple paths from peers. enable: Indicate that the system enables add-path support for the node. send: Indicate that the system sends multiple paths to peers.
PAGE 205
{deny | permit} {community-number | local-AS | no-advertise | no-export | quote-regexp regular-expression-list | regexp regular-expression} ● community-number: use AA:NN format where AA is the AS number (2 Bytes or 4 Bytes) and NN is a value specific to that autonomous system. ● local-AS: routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED. ● no-advertise: routes with the COMMUNITY attribute of NO_ADVERTISE. ● no-export: routes with the COMMUNITY attribute of NO_EXPORT.
PAGE 206
deny 701:20 deny 702:20 deny 703:20 deny 704:20 deny 705:20 deny 14551:20 deny 701:112 deny 702:112 deny 703:112 deny 704:112 deny 705:112 deny 14551:112 deny 701:667 deny 702:667 deny 703:667 deny 704:666 deny 705:666 deny 14551:666 DellEMC# Configure BGP attributes Following sections explain how to configure the BGP attributes such as MED, COMMUNITY, WEIGHT, and LOCAL_PREFERENCE.
PAGE 207
extended- Allows to send the extended community attribute to a BGP neighbor or peer group. standard- Allows to send the standard community attribute to a BGP neighbor or peer group. To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. If you want to remove or add a specific COMMUNITY number from a BGP path, you must create a route map with one or both of the following statements in the route map. Then apply that route map to a BGP neighbor or peer group. 1.
PAGE 208
*>i 6.10.0.0/15 *>i 6.14.0.0/15 *>i 6.133.0.0/21 *>i 6.151.0.0/16 --More-- 195.171.0.16 205.171.0.16 205.171.0.16 205.171.0.16 100 100 100 100 0 0 0 0 209 209 209 209 7170 7170 7170 7170 1455 1455 1455 1455 i i i i Changing the LOCAL_PREFERENCE Attribute In Dell EMC Networking OS, you can change the value of the LOCAL_PREFERENCE attribute, so that the preferred path can be changed. To change the default values of this attribute for all routes received by the router, use the following command.
PAGE 209
In the above example configuration, a route-map named route1 is created with a clause to set the specified local preference value, which is 140. To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. To view a routemap configuration, use the show route-map command in EXEC Privilege mode.
PAGE 210
Enabling Multipath By default, the software allows one path to a destination. You can enable multipath to allow up to 64 parallel paths to a destination. You can configure the maximum number of parallel routes (multipath support) to a destination in BGP. NOTE: Dell EMC Networking recommends not using multipath and add path simultaneously in a route reflector. To allow more than one path, use the following command. ● Enable multiple parallel paths.
PAGE 211
2. Router C receives the advertisement but does not advertise it to any peer because its only other peer is Router D, an iBGP peer, and Router D has already learned it through iBGP from Router B. 3. Router D does not advertise the route to Router C because Router C is a nonclient peer and the route advertisement came from Router B who is also a nonclient peer. 4. Router D does reflect the advertisement to Routers E and G because they are client peers of Router D. 5.
PAGE 212
● Attribute change When dampening is applied to a route, its path is described by one of the following terms: ● history entry — an entry that stores information on a downed route ● dampened path — a path that is no longer advertised ● penalized path — a path that is assigned a penalty To configure route flap dampening parameters, set dampening parameters using a route map, clear information on route dampening and return suppressed routes to active state, view statistics on route flapping, or change the path
PAGE 213
CONFIG-ROUTER-BGP mode bgp non-deterministic-med NOTE: When you change the best path selection method, path selection for existing paths remains unchanged until you reset it by entering the clear ip bgp command in EXEC Privilege mode. To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show running-config bgp command in EXEC Privilege mode. The following example shows how to configure values to reuse or restart a route.
PAGE 214
CONFIG-ROUTER-BGP mode neighbors {ip-address | ipv6-address | peer-group-name} timers keepalive holdtime ○ keepalive: Time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds. ○ holdtime: Time interval, in seconds, between the last keepalive message and declaring the BGP peer is dead. The range is from 3 to 65536. The default is 180 seconds. ● Configure timer values for all neighbors.
PAGE 215
CONFIGURATION Mode router bgp as-number 2. In ROUTER BGP mode, enter the following command: ROUTER BGP Mode shutdown all You can use the no shutdown all command in the ROUTER BGP mode to re-enable all the BGP interface. You can also enable or disable BGP neighbors corresponding to the IPv4 unicast or multicast address families and the IPv6 unicast address family. To enable or disable BGP neighbors corresponding to the IPv4 unicast address families, use the following commands: 1.
PAGE 216
Meaning, BGP neighbors corresponding to the IPv4 unicast or multicast address family and the IPv6 unicast address family that were explicitly disabled before the global shutdown remains in disabled state. Use the no shutdown address-familyipv4-unicast, no shutdown address-family-ipv4-multicast, or no shutdown address-family-ipv6unicast commands to enable these neighbors. NOTE: This behavior applies to all BGP neighbors.
PAGE 217
bgp confederation peers as-number [... as-number] ○ as-number: from 0 to 65535 (2 Byte) or from 1 to 4294967295 (4 Byte). All Confederation routers must be either 4 Byte or 2 Byte. You cannot have a mix of router ASN support. To view the configuration, use the show config command in CONFIGURATION ROUTER BGP mode. Configuring a BGP VRF address family To perform BGP configuration between two neighbors that must exchange IPv6 or IPv4 VRF information, use the following commands.
PAGE 218
Neighbor 50.0.0.2 AS 200 MsgRcvd 0 MsgSent 0 TblVer 0 InQ 0 OutQ Up/Down State/Pfx 0 00:00:00 0 Following is the output of show running-config bgp command for the above configuration. DellEMC#show running-config bgp ! router bgp 10 bgp router-id 1.1.1.1 network 10.10.21.0/24 bgp four-octet-as-support neighbor 20.20.20.1 remote-as 65550 neighbor 20.20.20.1 no shutdown ! address-family ipv4 vrf vrf1 neighbor 50.0.0.2 maximum-prefix 10000 warning-only neighbor 50.0.0.2 remote-as 200 neighbor 50.0.0.
PAGE 219
neighbor 100.10.92.9 local-as 6500 neighbor 100.10.92.9 no shutdown neighbor 192.168.10.1 remote-as 65123 neighbor 192.168.10.1 update-source Loopback 0 neighbor 192.168.10.1 no shutdown neighbor 192.168.12.2 remote-as 65123 neighbor 192.168.12.2 update-source Loopback 0 neighbor 192.168.12.2 no shutdown R2(conf-router_bgp)# Allowing an AS Number to Appear in its Own AS Path This command allows you to set the number of times a particular AS number can occur in the AS path.
PAGE 220
The default is IPv4 Unicast routes. When you configure a peer to support IPv4 multicast, Dell EMC Networking OS takes the following actions: ● Send a capability advertisement to the peer in the BGP Open message specifying IPv4 multicast as a supported AFI/SAFI (Subsequent Address Family Identifier). ● If the corresponding capability is received in the peer’s Open message, BGP marks the peer as supporting the AFI/SAFI.
PAGE 221
Following is the output of show ip bgp ipv6 unicast summary command for the above configuration example. DellEMC#show ip bgp ipv6 unicast summary BGP router identifier 1.1.1.
PAGE 222
Neighbor 20.20.20.2 30.30.30.1 2001::2 AS 200 20 200 MsgRcvd 10 0 40 MsgSent 20 0 45 TblVer 0 0 0 InQ 0 0 0 OutQ 0 0 0 Up/Down 00:06:11 00:00:00 00:03:14 State/Pfx 0 0 0 The same output will be displayed when using show ip bgp ipv4 unicast summary command. Following is the sample output of show ip bgp ipv4 multicast summary command. R1# show ip bgp ipv4 multicast summary BGP router identifier 1.1.1.
PAGE 223
Following is the output of show ip bgp ipv6 unicast summary command for the above configuration example. R2#show ip bgp ipv6 unicast summary BGP router identifier 2.2.2.2, local AS number 200 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 2 neighbor(s) using 24576 bytes of memory Neighbor 20.20.20.
PAGE 224
Following is the show running-config command output for the above configuration. DellEMC# show running-config bgp ! router bgp 655 bgp router-id 1.1.1.1 neighbor 10.1.1.2 remote-as 20 neighbor 10.1.1.2 auto-local-address neighbor 10.1.1.2 no shutdown ! address-family ipv6 unicast neighbor 10.1.1.2 activate exit-address-family ! Example configuration performed in R2 DellEMC# configure terminal DellEMC(conf)# router bgp 20 DellEMC(conf-router_bgp)# neighbor 10.1.1.
PAGE 225
Debugging BGP To enable BGP debugging, use any of the following commands. ● View all information about BGP, including BGP events, keepalives, notifications, and updates. EXEC Privilege mode debug ip bgp [ip-address | peer-group peer-group-name] [in | out] ● View information about BGP route being dampened. EXEC Privilege mode debug ip bgp dampening [in | out] ● View information about local BGP state changes and other BGP events.
PAGE 226
3 opens, 2 notifications, 0 updates 43 keepalives, 0 route refresh requests Minimum time between advertisement runs is 30 seconds Minimum time before advertisements start is 0 seconds Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP table version 1395, neighbor version 1394 Prefixes accepted 1
PAGE 227
10 Content Addressable Memory (CAM) CAM is a type of memory that stores information in the form of a lookup table. On Dell EMC Networking systems, CAM stores Layer 2 (L2) and Layer 3 (L3) forwarding information, access-lists (ACLs), flows, and routing policies.
PAGE 228
Table 11. Default Cam Allocation Settings (continued) CAM Allocation Setting ipv4pbr 0 vrfv4Acl 0 Openflow 0 fedgovacl 0 NOTE: When you reconfigure CAM allocation, use the nlbclusteracl number command to change the number of NLB ARP entries. The range is from 0 to 2. The default value is 0. At the default value of 0, eight NLB ARP entries are available for use. This platform supports upto 512 CAM entries. Select 1 to configure 256 entries. Select 2 to configure 1024 entries.
PAGE 229
The new cam region ipv6mirracl is introduced in the cam-acl command to configure dedicated FP CAM regions for the IPv6 mirror ACL entries. NOTE: If you do not enter the allocation values for the CAM regions, the value is 0. 3. Execute write memory and verify that the new settings are written to the CAM on the next boot. EXEC Privilege mode show cam-acl 4. Reload the system.
PAGE 230
Example of show running-config cam-profile Command Dell#show running-config cam-profile ! cam-profile default microcode default Dell# View CAM-ACL Settings The show cam-acl command shows the cam-acl setting that will be loaded after the next reload.
PAGE 231
L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : : : : : : : 1 block = 128 entries 6 4 0 2 1 0 0 0 0 0 0 0 0 0 0 0 -- Stack unit 0 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 -- Stack unit 7 -Cu
PAGE 232
Example of the show cam-usage Command DellEMC#show cam-usage Stackunit|Portpipe|Pipeline| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|========|=================|=============|=============|============== 1 | 0 | 0 | IN-L2 ACL | 0 | 0 | 0 | | | IN-L3 ACL | 2304 | 1 | 2303 | | | IN-L3 ECMP GRP | 2048 | 0 | 2048 | | | IN-V6 ACL | 0 | 0 | 0 | | | IN-NLB ACL | 0 | 0 | 0 | | | IPMAC ACL | 0 | 0 | 0 | | | IN-V6-MIRRACL | 0 | 0 | 0 | | | IN-L3-MIRR ACL | 0 | 0 | 0 | | | OUT-L2 ACL | 206 |
PAGE 233
Consider if the last CAM threshold was set to 90 percent and now you re-configure the CAM threshold to 80. And, if the current CAM usage is 85 percent, then the system displays the syslog message saying that the CAM usage is above the configured CAM threshold value. Table 13.
PAGE 234
Syslog Error When the Table is Full In the Dell EMC Networking OS, the table full condition is displayed as CAM full only for LPM. But now the LPM is split into two tables. There are two syslog errors that are displayed: 1. /65 to /128 Table full. 2. 0/0 – 0/64 Table full. A table-full error message is displayed once the number of entries is crossed the table size. Table-full message is generated only once when it crosses the threshold.
PAGE 235
DellEMC(conf)# DellEMC(conf)#end DellEMC#01:13:44: %STKUNIT0-M:CP %SYS-5-CONFIG_I: Configured from console DellEMC# 2. Display the hardware forwarding table mode in the current boot and in the next boot.
PAGE 236
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. That filter prevents traffic not specifically identified as legitimate from reaching the system control plane, rate-limits, traffic to an acceptable level.
PAGE 237
Figure 28. CoPP Implemented Versus CoPP Not Implemented Topics: • Configure Control Plane Policing Configure Control Plane Policing The system can process a maximum of 4200 packets per second (PPS). Protocols that share a single queue may experience flaps if one of the protocols receives a high rate of control traffic even though per protocol CoPP is applied. This happens because queue-based rate limiting is applied first.
PAGE 238
Configuring CoPP for Protocols This section lists the commands necessary to create and enable the service-policies for CoPP. For complete information about creating ACLs and QoS rules, refer to Access Control Lists (ACLs) and Quality of Service (QoS). The basics for creating a CoPP service policy are to create a Layer 2, Layer 3, and/or an IPv6 ACL rule for the desired protocol type. Then, create a QoS input policy to rate-limit the protocol traffics according to the ACL.
PAGE 239
DellEMC(conf)#mac access-list extended lacp cpu-qos DellEMC(conf-mac-acl-cpuqos)#permit lacp DellEMC(conf-mac-acl-cpuqos)#exit DellEMC(conf)#ipv6 access-list ipv6-icmp cpu-qos DellEMC(conf-ipv6-acl-cpuqos)#permit icmp DellEMC(conf-ipv6-acl-cpuqos)#exit DellEMC(conf)#ipv6 access-list ipv6-vrrp cpu-qos DellEMC(conf-ipv6-acl-cpuqos)#permit vrrp DellEMC(conf-ipv6-acl-cpuqos)#exit The following example shows creating the QoS input policy.
PAGE 240
1. Create a QoS input policy for the router and assign the policing. CONFIGURATION mode qos-policy-input name cpu-qos 2. Create an input policy-map to assign the QoS policy to the desired service queues.l. CONFIGURATION mode policy-map--input name cpu-qos service-queue queue-number qos-policy name 3. Enter Control Plane mode. CONFIGURATION mode control-plane-cpuqos 4. Assign a CPU queue-based service policy on the control plane in cpu-qos mode.
PAGE 241
Table 15.
PAGE 242
Displaying CoPP Configuration The CLI provides show commands to display the protocol traffic assigned to each control-plane queue and the current rate-limit applied to each queue. Other show commands display statistical information for trouble shooting CoPP operation. To view the rates for each queue, use the show cpu-queue rate cp command.
PAGE 243
Example of Viewing Queue Mapping for IPv6 Protocols DellEMC#show ipv6 protocol-queue-mapping Protocol Src-Port Dst-Port TcpFlag Queue EgPort Rate (kbps) --------------- -------- ------- ----- ------ ----------TCP (BGP) any/179 179/any _ Q6 CP _ ICMP any any _ Q6 CP _ VRRP any any _ Q7 CP _ DellEMC# Control Plane Policing (CoPP) 243
PAGE 244
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of enhancements to Ethernet local area networks used in data center environments, particularly with clustering and storage area networks.
PAGE 245
A CNA is a computer input/output device that combines the functionality of a host bus adapter (HBA) with a network interface controller (NIC). Multiple adapters on different devices for several traffic types are no longer required.
PAGE 246
Figure 29. Illustration of Traffic Congestion The system supports loading two DCB_Config files: ● FCoE converged traffic with priority 3. ● iSCSI storage traffic with priority 4. In the Dell EMC Networking OS, PFC is implemented as follows: ● PFC is supported on specified 802.1p priority traffic (dot1p 0 to 7) and is configured per interface.
PAGE 247
The following figure shows how ETS allows you to allocate bandwidth when different traffic types are classed according to 802.1p priority and mapped to priority groups. Figure 30. Enhanced Transmission Selection The following table lists the traffic groupings ETS uses to select multiprotocol traffic for transmission. Table 16. ETS Traffic Groupings Traffic Groupings Description Group ID A 4-bit identifier assigned to each priority group. The range is from 0 to 7 configurable; 8 - 14 reservation and 15.
PAGE 248
Data Center Bridging in a Traffic Flow The following figure shows how DCB handles a traffic flow on an interface. Figure 31. DCB PFC and ETS Traffic Handling Enabling Data Center Bridging DCB is automatically configured when you configure FCoE or iSCSI optimization. Data center bridging supports converged enhanced Ethernet (CEE) in a data center network. DCB is disabled by default. It must be enabled to support CEE.
PAGE 249
DCB Maps and its Attributes This topic contains the following sections that describe how to configure a DCB map, apply the configured DCB map to a port, configure PFC without a DCB map, and configure lossless queues. DCB Map: Configuration Procedure A DCB map consists of PFC and ETS parameters. By default, PFC is not enabled on any 802.1p priority and ETS allocates equal bandwidth to each priority. To configure user-defined PFC and ETS settings, you must create a DCB map.
PAGE 250
PFC is not applied on specific dot1p priorities. ETS: Equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure PFC and ETS parameters on an interface, you must specify the PFC mode, the ETS bandwidth allocation for a priority group, and the 802.1p priority-to-priority group mapping in a DCB map. No default PFC and ETS settings are applied to Ethernet interfaces.
PAGE 251
Port A —> Port B Port C —> Port B PFC no-drop queues are configured for queues 1, 2 on Port B. PFC capability is enabled on priorities 3, 4 on PORT A and C. Port B acting as Egress During the congestion, [traffic pump on priorities 3 and 4 from PORT A and PORT C is at full line rate], PORT A and C send out the PFCs to rate the traffic limit. Egress drops are not observed on Port B since traffic flow on priorities is mapped to loss less queues.
PAGE 252
NOTE: Dell EMC Networking OS Behavior: By default, no lossless queues are configured on a port. A limit of two lossless queues is supported on a port. If the amount of priority traffic that you configure to be paused exceeds the two lossless queues, an error message displays. In S6000, any pfc-dot1p priorities configured on a given interface need not be the same across the system. In other words, lossless queue limit is applicable on a per-port level and not on the global-config context.
PAGE 253
● When you apply a DCB map, an error message is displayed if link-level flow control is already enabled on an interface. You cannot enable PFC and link-level flow control at the same time on an interface. ● In a switch stack, configure all stacked ports with the same PFC configuration. ● Dell EMC Networking OS allows you to change the default dot1p priority-queue assignments only if the change satisfies the following requirements in DCB maps already applied to the interfaces: ● All 802.
PAGE 254
Configuring no-drop queues is applicable only on the interfaces which do not need PFC. Example: Port A —> Port B Port C —> Port B PFC no-drop queues are configured for queues 1, 2 on Port B. PFC capability is enabled on priorities 3, 4 on PORT A and C. Port B acting as Egress During the congestion, [traffic pump on priorities 3 and 4 from PORT A and PORT C is at full line rate], PORT A and C send out the PFCs to rate the traffic limit.
PAGE 255
Table 18. Configuring Lossless Queues on a Port Interface (continued) Step Task Command Command Mode Range: 0-3. Separate queue values with a comma; specify a priority range with a dash; for example: pfc no-drop queues 1,3 or pfc no-drop queues 2-3 Default: No lossless queues are configured.
PAGE 256
Behavior of Tagged Packets The below is example for enabling PFC for priority 2 for tagged packets. Priority (Packet Dot1p) 2 will be mapped to PG6 on PRIO2PG setting. All other Priorities for which PFC is not enabled are mapped to default PG – PG7. Classification rules on ingress (Ingress FP CAM region) matches incoming packet-dot1p and assigns an internal priority (to select queue as per Table 1 and Table 2).
PAGE 257
Table 19. Queue Assignments Internal-priority Queue 0 2 1 0 2 1 3 3 4 4 5 5 6 6 7 7 3. Dot1p->Queue Mapping Configuration is retained at the default value. Default dot1p-queue mapping is, DellEMC#show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 Queue : 2 0 1 3 4 5 6 7 7 4. Interface Configurations on server connected ports. a. Enable DCB globally. DellEMC(conf)#dcb enable b. Apply PFC Priority configuration. Configure priorities on which PFC is enabled.
PAGE 258
dellNetFpStatsPe This table fetches the Allocated Min cells, Shared cells, and Headroom cells per Priority Group, the mode rPgTable in which the buffer cells are allocated — Static or Dynamic and the Used Min Cells, Shared cells and Headroom cells per Priority Group. The table fetches a value of 0 if the mode of allocation is Static and a value of 1 if the mode of allocation is Dynamic. This table lists thestack-unit number, port number and priority group number.
PAGE 259
Table 21. Dot1p to Queue Mapping Packet-Dot1p Queue 0 2 1 0 2 1 3 3 4 4 5 5 6 6 7 7 PFC and ETS Configuration Examples This section contains examples of how to configure and apply DCB policies on an interface. Using PFC to Manage Converged Ethernet Traffic To use PFC for managing converged Ethernet traffic, use the following command: dcb-map stack-unit all dcb-map-name Operations on Untagged Packets The below is example for enabling PFC for priority 2 for tagged packets.
PAGE 260
Generation of PFC for a Priority for Untagged Packets In order to generate PFC for a particular priority for untagged packets, and configuring PFC for that priority, you should find the queue number associated with priority from TABLE 1 and Associate a DCB map to forward the matched DSCP packet to that queue. PFC frames gets generated with PFC priority associated with the queue when the queue gets congested.
PAGE 261
PRIORITY-GROUP mode exit 5. Repeat Steps 1 to 4 to configure all remaining dot1p priorities in an ETS priority group. 6. Specify the dot1p priority-to-priority group mapping for each priority. priority-pgid dot1p0_group_num dot1p1_group_num ...dot1p7_group_num Priority group range is from 0 to 7. All priorities that map to the same queue must be in the same priority group. Leave a space between each priority group number.
PAGE 262
To create a QoS output policy that allocates different amounts of bandwidth to the different traffic types/ dot1p priorities assigned to a queue and apply the output policy to the interface, follow these steps. 1. Create a QoS output policy. CONFIGURATION mode Dell(conf)#qos-policy-output test12 The maximum 32 alphanumeric characters. 2. Configure the percentage of bandwidth to allocate to the dot1p priority/queue traffic in the associated L2 class map.
PAGE 263
parameter. The sum of the bandwidth allocated to all priority groups in a DCB map must be 100% of the bandwidth on the link. You must allocate at least 1% of the total bandwidth to each priority group. ● Scheduling of priority traffic: dot1p priority traffic on the switch is scheduled to the current queue mapping. dot1p priorities within the same queue must have the same traffic properties and scheduling method.
PAGE 264
● If priority group 3 has free bandwidth, it is distributed as follows: 20% of the free bandwidth to priority group 1 and 30% of the free bandwidth to priority group 2. ● If priority group 1 or 2 has free bandwidth, (20 + 30)% of the free bandwidth is distributed to priority group 3. Priority groups 1 and 2 retain whatever free bandwidth remains up to the (20+ 30)%.
PAGE 265
● Accepts the DCB configuration from a peer if a DCBx port is in “willing” mode to accept a peer’s DCB settings and then internally propagates the received DCB configuration to its peer ports. DCBx Port Roles To enable the auto-configuration of DCBx-enabled ports and propagate DCB configurations learned from peer DCBx devices internally to other switch ports, use the following DCBx port roles.
PAGE 266
When making a configuration change to a DCBx port in a Manual role, Dell EMC Networking recommends shutting down the interface using the shutdown command, change the configuration, then re-activate the interface using the no shutdown command. The default for the DCBx port role is manual.
PAGE 267
Propagation of DCB Information When an auto-upstream or auto-downstream port receives a DCB configuration from a peer, the port acts as a DCBx client and checks if a DCBx configuration source exists on the switch. ● If a configuration source is found, the received configuration is checked against the currently configured values that are internally propagated by the configuration source.
PAGE 268
Figure 32. DCBx Sample Topology DCBx Prerequisites and Restrictions The following prerequisites and restrictions apply when you configure DCBx operation on a port: ● For DCBx, on a port interface, enable LLDP in both Send (TX) and Receive (RX) mode (the protocol lldp mode command; refer to the example in CONFIGURATION versus INTERFACE Configurations in the Link Layer Discovery Protocol (LLDP) chapter). If multiple DCBx peer ports are detected on a local DCBx interface, LLDP is shut down.
PAGE 269
The default is Auto. 4. Configure the DCBx port role the interface uses to exchange DCB information. PROTOCOL LLDP mode [no] DCBx port-role {config-source | auto-downstream | auto-upstream | manual} ● auto-upstream: configures the port to receive a peer configuration. The configuration source is elected from autoupstream ports. ● auto-downstream: configures the port to accept the internally propagated DCB configuration from a configuration source.
PAGE 270
● auto: configures all ports to operate using the DCBx version received from a peer. ● cee: configures a port to use CEE (Intel 1.01). cin configures a port to use Cisco-Intel-Nuova (DCBx 1.0). ● ieee-v2.5: configures a port to use IEEE 802.1Qaz (Draft 2.5). The default is Auto. NOTE: To configure the DCBx port role the interfaces use to exchange DCB information, use the DCBx port-role command in INTERFACE Configuration mode (Step 3). 4.
PAGE 271
DCBx Error Messages The following syslog messages appear when an error in DCBx operation occurs. LLDP_MULTIPLE_PEER_DETECTED: DCBx is operationally disabled after detecting more than one DCBx peer on the port interface. LLDP_PEER_AGE_OUT: DCBx is disabled as a result of LLDP timing out on a DCBx peer interface. DSM_DCBx_PEER_VERSION_CONFLICT: A local port expected to receive the IEEE, CIN, or CEE version in a DCBx TLV from a remote peer but received a different, conflicting DCBx version.
PAGE 272
Table 22. Displaying DCB Configurations (continued) Command Output show dcb [stack-unit unit-number] Displays the data center bridging status, number of PFCenabled ports, and number of PFC-enabled queues. On the master switch in a stack, you can specify a stack-unit number. The range is from 0 to 5. show qos priority-groups Displays the ETS priority groups configured on the switch, including the 802.1p priority classes and ID of each group.
PAGE 273
PG:0 TSA:ETS BW:50 PFC:OFF Priorities:0 1 2 5 6 7 PG:1 TSA:ETS BW:50 Priorities:3 4 PFC:ON The following example shows the show interfaces pfc summary command.
PAGE 274
Table 23. show interface pfc summary Command Description (continued) Fields Description DCBx exchange (Willing bit received in PFC TLV): enabled or disabled. Local is enabled DCBx operational status (enabled or disabled) with a list of the configured PFC priorities Operational status (local port) DCBx operational status (enabled or disabled) with a list of the configured PFC priorities.
PAGE 275
Te Te Te Te Te Te Te 1/1 1/1 1/1 1/1 1/1 1/1 1/1 P1 P2 P3 P4 P5 P6 P7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The following example shows the show interface ets summary command.
PAGE 276
1 2 3 4 5 6 7 Priority# Bandwidth TSA 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# 0 0,1,2,3,4,5,6,7 1 2 3 4 5 6 7 0% 0% 0% 0% 0% 0% 0% ETS ETS ETS ETS ETS ETS ETS 13% 13% 13% 13% 12% 12% 12% 12% ETS ETS ETS ETS ETS ETS ETS ETS Bandwidth 100% 0% 0% 0% 0% 0% 0% 0% TSA ETS ETS ETS ETS ETS ETS ETS ETS Priority# Bandwidth 0 13% 1 13% 2 13% 3 13% 4 12% 5 12% 6 12% 7 12% Oper status is init Conf TLV Tx Status i
PAGE 277
Table 24. show interface ets detail Command Description (continued) Field Description exchange, the Willing bit received in ETS TLVs from the remote peer is included. Local Parameters ETS configuration on local port, including Admin mode (enabled when a valid TLV is received from a peer), priority groups, assigned dot1p priorities, and bandwidth allocation.
PAGE 278
2 3 4 5 6 7 8 - - Stack unit 1 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 The following example shows the show interface DCBx detail command (IEEE).
PAGE 279
Local DCBx TLVs Transmitted: ErPFi Local DCBx Status ----------------DCBx Operational Version is 0 DCBx Max Version Supported is 0 Sequence Number: 1 Acknowledgment Number: 1 Protocol State: In-Sync Peer DCBx Status: ---------------DCBx Operational Version is 0 DCBx Max Version Supported is 0 Sequence Number: 1 Acknowledgment Number: 1 Total DCBx Frames transmitted 994 Total DCBx Frames received 646 Total DCBx Frame errors 0 Total DCBx Frames unrecognized 0 The following table describes the show interface D
PAGE 280
Table 25. show interface DCBx detail Command Description (continued) Field Description Peer DCBx Status: Acknowledgment Number Acknowledgement number transmitted in Control TLVs received from peer device. Total DCBx Frames transmitted Number of DCBx frames sent from local port. Total DCBx Frames received Number of DCBx frames received from remote peer port. Total DCBx Frame errors Number of DCBx frames with errors received.
PAGE 281
1. Enable the DCB application. By default, DCB is enabled and link-level flow control is disabled on all interfaces. CONFIGURATION mode dcb enable 2. Configure the shared PFC buffer size and the total buffer size. A maximum of 4 lossless queues are supported. CONFIGURATION mode dcb pfc-shared-buffer-size value dcb pfc-total-buffer-size value The buffer size range is from 0 to 3399. Default is 3088. 3. Configure the number of PFC queues.
PAGE 282
Figure 33. PFC and ETS Applied to LAN, IPC, and SAN Priority Traffic QoS Traffic Classification: The service-class dynamic dot1p command has been used in Global Configuration mode to map ingress dot1p frames to the queues shown in the following table. For more information, refer to QoS dot1p Traffic Classification and Queue Assignment.
PAGE 283
The following describes the priority group-bandwidth assignment. Priority Group Bandwidth Assignment IPC 5% SAN 50% LAN 45% PFC and ETS Configuration Command Examples The following examples show PFC and ETS configuration commands to manage your data center traffic. 1. Enabling DCB DellEMC(conf)#dcb enable 2. Configure DCB map and enable PFC, and ETS DellEMC(conf)# service-class dynamic dot1p Or DellEMC(conf)# interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)# service-class dynamic dot1p 3.
PAGE 284
13 Dynamic Host Configuration Protocol (DHCP) DHCP is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network endstations (hosts) based on configuration policies determined by network administrators.
PAGE 285
Option Number and Description Subnet Mask Option 1 Specifies the client’s subnet mask. Router Option 3 Specifies the router IP addresses that may serve as the client’s default gateway. Domain Name Server Option 6 Domain Name Option 15 Specifies the domain name servers (DNSs) that are available to the client. Specifies the domain name that clients should use when resolving hostnames via DNS.
PAGE 286
1. The client initially broadcasts a DHCPDISCOVER message on the subnet to discover available DHCP servers. This message includes the parameters that the client requires and might include suggested values for those parameters. 2. Servers unicast or broadcast a DHCPOFFER message in response to the DHCPDISCOVER that offers to the client values for the requested parameters. Multiple servers might respond to a single DHCPDISCOVER; the client might wait a period of time and then act on the most preferred offer.
PAGE 287
● All platforms support Dynamic ARP Inspection on 16 VLANs per system. For more information, refer to Dynamic ARP Inspection. NOTE: If the DHCP server is on the top of rack (ToR) and the VLTi (ICL) is down due to a failed link, when a VLT node is rebooted in BMP (Bare Metal Provisioning) mode, it is not able to reach the DHCP server, resulting in BMP failure.
PAGE 288
DHCP mode show config After an IP address is leased to a client, only that client may release the address. Dell EMC Networking OS performs a IP + MAC source address validation to ensure that no client can release another clients address. This validation is a default behavior and is separate from IP+MAC source address validation.
PAGE 289
Configure a Method of Hostname Resolution Dell systems are capable of providing DHCP clients with parameters for two methods of hostname resolution—using DNS or NetBIOS WINS. Using DNS for Address Resolution A domain is a group of networks. DHCP clients query DNS IP servers when they need to correlate host names to IP addresses. 1. Create a domain. DHCP domain-name name 2. Specify in order of preference the DNS servers that are available to a DHCP client.
PAGE 290
Debugging the DHCP Server To debug the DHCP server, use the following command. ● Display debug information for DHCP server. EXEC Privilege mode debug ip dhcp server [events | packets] Using DHCP Clear Commands To clear DHCP binding entries, address conflicts, and server counters, use the following commands. ● Clear DHCP binding entries for the entire binding table. EXEC Privilege mode. clear ip dhcp binding ● Clear a DHCP binding entry for an individual IP address. EXEC Privilege mode.
PAGE 291
Configuring the DHCP Client System This section describes how to configure and view an interface as a DHCP client to receive an IP address. Dell EMC Networking OS Behavior: The ip address dhcp command enables DHCP server-assigned dynamic addresses on an interface. The setting persists after a switch reboot. To stop DHCP transactions and save the dynamically acquired IP address, use the shutdown command on the interface.
PAGE 292
● To display dynamic IP address lease information currently assigned to a DHCP client interface, use the show ip dhcp lease [interface type slot/port] command. ● To display log messages for all DHCP packets sent and received on DHCP client interfaces, use the debug ip dhcp client packets [interface type slot/port command.
PAGE 293
DHCP Snooping A DHCP client can run on a switch simultaneously with the DHCP snooping feature as follows: ● If you enable DHCP snooping globally on a switch and you enable a DHCP client on an interface, the trust port, source MAC address, and snooping table validations are not performed on the interface by DHCP snooping for packets destined to the DHCP client daemon. The following criteria determine packets destined for the DHCP client: ○ DHCP is enabled on the interface.
PAGE 294
! ip vrf VRF_2 ip route-import 2:2 ip route-export 1:1 ! route-map rmap1 permit 10 match source-protocol connected ! route-map map2 permit 20 match source-protocol connected Route Leaking for Complete Routing Table ! ip vrf VRF_1 ip route-import 1:1 ip route-export 2:2 ! ip vrf VRF_2 ip route-import 2:2 ip route-export 1:1 Route Leaking for Selective Routes ! ip vrf VRF_1 ip route-import 1:1 map1 ip route-export 2:2 map2 ! ip vrf VRF_2 ip route-import 2:2 ip route-export 1:1 ! ! route-map map1 permit 10 m
PAGE 295
INTERFACE mode ipv6 helper-address [vrf vrf-name] ipv6-address Configuring DHCP relay source interface The following section explains how to configure global and interface level DHCP relay source IPv4 or IPv6 configuration to forward all the DHCP packets from the DHCP client to DHCP server through the configured source interface. This feature is applicable only for L3 interface with relay configuration and L3 DHCP snooping enabled VLANs.
PAGE 296
1. Configuring L3 interface with IPv4 or IPv6 address. Following are the steps to configure a L3 interface (loopback) with IPv4 and IPv6 address in INTERFACE MODE. Dell(conf)# interface loopback 2 Dell(conf-if-lo-1)# ip vrf forwarding vrf1 Dell(conf-if-lo-1)# ip address 2.2.2.2/32 Dell(conf-if-lo-1)# ipv6 address 2::2/128 Dell(conf-if-lo-1)# no shutdown Dell(conf)# interface loopback 3 Dell(conf-if-lo-1)# ip vrf forwarding vrf2 Dell(conf-if-lo-1)# ip address 3.3.3.
PAGE 297
The received stacking configuration is always applied on the master stack unit. option #230 "unit-number:3#priority:2#stack-group:14" Configure Secure DHCP DHCP as defined by RFC 2131 provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks.
PAGE 298
ip dhcp relay information-option remote-id DHCPv6 relay agent options The DHCPv6 relay agent inserts Options 18 and 37 before forwarding DHCPv6 packets to the server. These DHCPv6 options are enabled by default and are not configurable. Interface ID (Option 18) Remote ID (Option 37) Interface on which the client-originated message is received. The interface-ID is 12 bytes long and is constructed using three ifindexes: Logical, Received, and Physical. Each of the ifindex is 4 bytes long.
PAGE 299
NOTE: If you enable DHCP Option 82 using the ip dhcp relay command, by default, the remote-ID field contains the MAC address of the relay agent. If you configure the remote ID as the host name in a VLT setup, configure different host names on both VLT peers. If you configure the remote ID with your own string, ensure that your strings are different on both VLT peers. DHCP Snooping in a VLT Setup In a VLT setup, the DHCP snooping binding table synchronizes between the VLT nodes.
PAGE 300
Adding a Static IPV6 DHCP Snooping Binding Table To add a static entry in the snooping database, use the following command. ● Add a static entry in the snooping binding table. EXEC Privilege mode ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease value Clearing the Binding Table To clear the binding table, use the following command. ● Delete all of the entries in the binding table.
PAGE 301
Invalid Binding List of List of List of Binding Entry Entry lease expired Trust Ports DHCP Snooping Enabled Vlans DAI Trust ports : 0 : 0 :Te 1/4 :Vl 10 :Te 1/4 View the DHCP snooping binding table using the show ip dhcp snooping binding command. DellEMC#show ip dhcp snooping binding Codes : S - Static D - Dynamic IP Address MAC Address Expires(Sec) Type VLAN Interface ========================================================================= 10.1.1.254 00:00:a0:00:00:02 162 D Vl 200 Te 1/4 10.1.1.
PAGE 302
View the DHCP snooping statistics with the show ipv6 dhcp snooping command. DellEMC#show ipv6 dhcp snooping binding Codes : S - Static D – Dynamic IPv6 Address MAC Address Expires(Sec) Type VLAN Interface ========================================================================= 11:11::22 11:22:11:22:11:22 120331 S Vl 100 Te 1/1 33::22 11:22:11:22:11:23 120331 S Vl 200 Te 1/1 333:22::22 11:22:11:22:11:24 120331 D Vl 300 Te 1/2 Debugging the IPv6 DHCP To debug the IPv6 DHCP, use the following command.
PAGE 303
Drop DHCP Packets on Snooped VLANs Only Binding table entries are deleted when a lease expires or the relay agent encounters a DHCPRELEASE. Line cards maintain a list of snooped VLANs. When the binding table fills, DHCP packets are dropped only on snooped VLANs, while such packets are forwarded across non-snooped VLANs. Because DHCP packets are dropped, no new IP address assignments are made. However, DHCP release and decline packets are allowed so that the DHCP snooping table can decrease in size.
PAGE 304
arp inspection To view entries in the ARP database, use the show arp inspection database command. DellEMC#show arp inspection database Protocol Address Age(min) Hardware Address Interface VLAN CPU --------------------------------------------------------------------Internet 10.1.1.251 00:00:4d:57:f2:50 Te 1/2 Vl 10 CP Internet 10.1.1.252 00:00:4d:57:e6:f6 Te 1/1 Vl 10 CP Internet 10.1.1.253 00:00:4d:57:f8:e8 Te 1/3 Vl 10 CP Internet 10.1.1.
PAGE 305
Source Address Validation Using the DHCP binding table, Dell EMC Networking OS can perform three types of source address validation (SAV). Table 28. Three Types of Source Address Validation Source Address Validation Description IP Source Address Validation Prevents IP spoofing by forwarding only IP packets that have been validated against the DHCP binding table.
PAGE 306
Enabling IP+MAC Source Address Validation IP source address validation (SAV) validates the IP source address of an incoming packet and optionally the VLAN ID of the client against the DHCP snooping binding table. IP+MAC SAV ensures that the IP source address and MAC source address are a legitimate pair, rather than validating each attribute individually. You cannot configure IP+MAC SAV with IP SAV. 1. Allocate at least one FP block to the ipmacacl CAM region. CONFIGURATION mode cam-acl l2acl 2.
PAGE 307
Clearing the Number of SAV Dropped Packets To clear the number of SAV dropped packets, use the clear ip dhcp snooping source-address-validation discard-counters command. DellEMC>clear ip dhcp snooping source-address-validation discard-counters To clear the number of SAV dropped packets on a particular interface, use the clear ip dhcp snooping sourceaddress-validation discard-counters interface interface command.
PAGE 308
14 Equal Cost Multi-Path (ECMP) This chapter describes configuring ECMP. This chapter describes configuring ECMP. Topics: • • • • ECMP for Flow-Based Affinity Link Bundle Monitoring RTAG7 Flow-based Hashing for ECMP ECMP for Flow-Based Affinity ECMP for flow-based affinity includes link bundle monitoring.
PAGE 309
Configuring the Hash Algorithm Seed Deterministic ECMP sorts ECMPs in order even though RTM provides them in a random order. However, the hash algorithm uses as a seed the lower 12 bits of the chassis MAC, which yields a different hash result for every chassis. This behavior means that for a given flow, even though the prefixes are sorted, two unrelated chassis can select different hops.
PAGE 310
Managing ECMP Group Paths To avoid path degeneration, configure the maximum number of paths for an ECMP route that the L3 CAM can hold. When you do not configure the maximum number of routes, the CAM can hold a maximum ECMP per route. To configure the maximum number of paths, use the following command. NOTE: For the new settings to take effect, save the new ECMP settings to the startup-config (write-mem) then reload the system. ● Configure the maximum number of paths per ECMP group. CONFIGURATION mode.
PAGE 311
NOTE: An ecmp-group index is generated automatically for each unique ecmp-group when you configure multipath routes to the same network. The system can generate a maximum of 512 unique ecmp-groups. The ecmp-group indices are generated in even numbers (0, 2, 4, 6... 1022) and are for information only. You can configure ecmp-group with id 2 for link bundle monitoring. This ecmp-group is different from the ecmp-group index 2 that is created by configuring routes and is automatically generated.
PAGE 312
Support for moving /128 IPv6 Prefixes and /32 IPv4 Prefixes The software supports a command to program IPv6 /128 route prefixes in the route table. You can define IPv6 /128 route prefixes in the route table using the ipv6 unicast-host-routecommand. You can also define IPv4 /32 route prefixes in the host table using the ipv4 unicast-host-routecommand. RTAG7 RTAG7 is a hashing algorithm that load balances the traffic within a trunk group in a controlled manner.
PAGE 313
● RTAG7 hashing also provides options to select between multiple hash algorithms that would result in balanced traffic distribution for various traffic patterns.
PAGE 314
Figure 36. Before Polarization Effect Router B performs the same hash as router A and all the traffic goes through the same path to router D, while no traffic is redirected to router E. Some of the anti-polarization techniques used generally to mitigate unequal traffic distribution in LAG/ECMP as follows: 1. Configuring different hash-seed values at each node - Hash seed is the primary parameter in hash computations that determine distribution of traffic among the ECMP paths.
PAGE 315
bits of xor4 xor8 bits of xor8 xor16 CRC16_BISYNC_AND_XOR8 - Upper 8 bits of CRC16-BISYNC and lower 8 CR16 - 16 bit XOR] Example to view show hash-algorithm: DellEMC(conf)#hash-algorithm ecmp flow-based-hashing crc16 DellEMC(conf)#end DellEMC#show hash-algorithm Hash-Algorithm linecard 0 Port-Set 0 Seed 185270328 Hg-Seed 185282673 EcmpFlowBasedHashingAlgo- crc16 EcmpAlgo- crc32MSB LagAlgo- crc32LSB HgAlgo- crc16 Figure 37.
PAGE 316
15 FIP Snooping The Fibre Channel over Ethernet (FCoE) Transit feature is supported on Ethernet interfaces. When you enable the switch for FCoE transit, the switch functions as a FIP snooping bridge. NOTE: FIP snooping is not supported on Fibre Channel interfaces or in a switch stack.
PAGE 317
The following table lists the FIP functions. Table 29. FIP Functions FIP Function Description FIP VLAN discovery FCoE devices (ENodes) discover the FCoE VLANs on which to transmit and receive FIP and FCoE traffic. FIP discovery FCoE end-devices and FCFs are automatically discovered. Initialization FCoE devices learn ENodes from the FLOGI and FDISC to allow immediate login and create a virtual link with an FCoE switch.
PAGE 318
Dynamic ACL generation on the switch operating as a FIP snooping bridge function as follows: Port-based ACLs These ACLs are applied on all three port modes: on ports directly connected to an FCF, server-facing ENode ports, and bridge-to-bridge links. Port-based ACLs take precedence over global ACLs. FCoE-generated ACLs These take precedence over user-configured ACLs. A user-configured ACL entry cannot deny FCoE and FIP snooping frames.
PAGE 319
● To ensure that they are operationally active, check FIP snooping-enabled VLANs. ● Process FIP VLAN discovery requests and responses, advertisements, solicitations, FLOGI/FDISC requests and responses, FLOGO requests and responses, keep-alive packets, and clear virtual-link messages. FIP Snooping in a Switch Stack FIP snooping supports switch stacking as follows: ● A switch stack configuration is synchronized with the standby stack unit.
PAGE 320
○ ACLs are not installed, FIP and FCoE traffic is not blocked, and FIP packets are not processed. ○ The existing per-VLAN and FIP snooping configuration is stored. The configuration is re-applied the next time you enable the FIP snooping feature. ● You must apply the CAM-ACL space for the FCoE region before enabling the FIP-Snooping feature. If you do not apply CAM-ACL space, the following error message is displayed: DellEMC(conf)#feature fip-snooping % Error: Cannot enable fip snooping.
PAGE 321
● FCoE traffic is allowed on VLANs only after a successful virtual-link initialization (fabric login FLOGI) between an ENode and an FCF. All other FCoE traffic is dropped. ● You must configure at least one interface for FCF (FCoE Forwarder) mode on a FIP snooping-enabled VLAN. You can configure multiple FCF trusted interfaces in a VLAN. ● A maximum of eight VLANS are supported for FIP snooping on the switch.
PAGE 322
Table 30. Impact of Enabling FIP Snooping (continued) Impact Description deleted. If a port is enabled for FIP snooping in ENode or FCF mode, the ENode/FCF MAC-based ACLs are deleted. FIP Snooping Restrictions The following restrictions apply when you configure FIP snooping. ● The maximum number of FCoE VLANs supported on the switch is eight. ● The maximum number of FIP snooping sessions supported per ENode server is 32.
PAGE 323
Displaying FIP Snooping Information Use the following show commands to display information on FIP snooping. Table 31. Displaying FIP Snooping Information Command Output show fip-snooping sessions [interface vlan vlan-id] Displays information on FIP-snooped sessions on all VLANs or a specified VLAN, including the ENode interface and MAC address, the FCF interface and MAC address, VLAN ID, FCoE MAC address and FCoE session ID number (FC-ID), worldwide node name (WWNN) and the worldwide port name (WWPN).
PAGE 324
Table 32. show fip-snooping sessions Command Description Field Description ENode MAC MAC address of the ENode . ENode Interface Slot/port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. FCF Interface Slot/port number of the interface to which the FCF is connected. VLAN VLAN ID number used by the session. FCoE MAC MAC address of the FCoE session assigned by the FCF. FC-ID Fibre Channel ID assigned by the FCF. Port WWPN Worldwide port name of the CNA port.
PAGE 325
Table 34. show fip-snooping fcf Command Description (continued) Field Description FCF Interface Slot/port number of the interface to which the FCF is connected. VLAN VLAN ID number used by the session. FC-MAP FC-Map value advertised by the FCF. ENode Interface Slot/port number of the interface connected to the ENode. FKA_ADV_PERIOD Period of time (in milliseconds) during which FIP keep-alive advertisements are transmitted. No of ENodes Number of ENodes connected to the FCF.
PAGE 326
The following example shows the show fip-snooping statistics port-channel command.
PAGE 327
Table 35. show fip-snooping statistics Command Descriptions (continued) Field Description Number of FDISC Rejects Number of FIP FDISC reject frames received on the interface. Number of FLOGO Accepts Number of FIP FLOGO accept frames received on the interface. Number of FLOGO Rejects Number of FIP FLOGO reject frames received on the interface. Number of CVLs Number of FIP clear virtual link frames received on the interface.
PAGE 328
FCoE Transit Configuration Example The following illustration shows a switch used as a FIP snooping bridge for FCoE traffic between an ENode (server blade) and an FCF (ToR switch). The ToR switch operates as an FCF and FCoE gateway. Figure 40. Configuration Example: FIP Snooping on a Switch In this example, DCBx and PFC are enabled on the FIP snooping bridge and on the FCF ToR switch.
PAGE 329
Example of Configuring the ENode Server-Facing Port DellEMC(conf)# interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)# portmode hybrid DellEMC(conf-if-te-1/1)# switchport DellEMC(conf-if-te-1/1)# protocol lldp DellEMC(conf-if-te-1/1-lldp)# dcbx port-role auto-downstream NOTE: A port is enabled by default for bridge-ENode links.
PAGE 330
16 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Topics: • • • • • • • Flex Hash Capability Overview Configuring the Flex Hash Mechanism Configuring Fast Boot and LACP Fast Switchover Optimizing the Boot Time Interoperation of Applications with Fast Boot and System States RDMA Over Converged Ethernet (RoCE) Overview Preserving 802.
PAGE 331
Flex hash APIs do not mask out unwanted byte values after extraction of the data from the Layer 4 headers for the offset value. 2. Use the load-balance flexhash command to specify whether IPv4 or IPv6 packets must be subjected to the flex hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name.
PAGE 332
unexpected shutdown) from an older release of Dell EMC Networking OS to Release 9.3(0.0) or later. Dell EMC recommends that you do not downgrade your system from Release 9.3(0.0) to an earlier release that does not support the fast boot functionality because the system behavior is unexpected and undefined. ● Fast boot uses the Symmetric Multiprocessing (SMP) utility that is enabled on the Intel CPU on the device to enhance the speed of the system startup. SMP is supported on the device.
PAGE 333
A file is generated to indicate that the system is undergoing a fast boot, which is used after the system comes up. After the Dell EMC Networking OS image is loaded and activated, and the appropriate software components come up, the following additional actions are performed: ● If a database of dynamic ARP entries is present on the flash drive, that information is read and the ARP entries are restored; the entries are installed on the switch as soon as possible.
PAGE 334
Unexpected Reload of the System When an unexpected or unplanned reload occurs, such as a reset caused by the software, the system performs the regular boot sequence even if it is configured for fast boot. When the system comes up, dynamic ARP or ND database entries are not present or required to be restored. The system boot up mode will not be fast boot and actions specific to this mode will not be performed.
PAGE 335
RDMA Over Converged Ethernet (RoCE) Overview This functionality is supported on the S6000 platform. RDMA is a technology that a virtual machine (VM) uses to directly transfer information to the memory of another VM, thus enabling VMs to be connected to storage networks. With RoCE, RDMA enables data to be forwarded without passing through the CPU and the main memory path of TCP/IP.
PAGE 336
except the Layer 2 and Layer 3 control frames. It is not required for a VLAN ID to be preserved (in the hardware or the OS application) when a VLAN ID, used for encapsulation, is associated with a physical/Port-channel interface. Normal VLANs and VLAN encapsulation can exist simultaneously and any non-unicast traffic received on a normal VLAN is not flooded using lite subinterfaces whose encapsulation VLAN ID matches with that of the normal VLAN ID.
PAGE 337
17 Force10 Resilient Ring Protocol (FRRP) FRRP provides fast network convergence to Layer 2 switches interconnected in a ring topology, such as a metropolitan area network (MAN) or large campuses. FRRP is similar to what can be achieved with the spanning tree protocol (STP), though even with optimizations, STP can take up to 50 seconds to converge (depending on the size of network and node of failure) and may require 4 to 5 seconds to reconverge.
PAGE 338
Ring Status The ring failure notification and the ring status checks provide two ways to ensure the ring remains up and active in the event of a switch or port failure. Ring Checking At specified intervals, the Master node sends a ring health frame (RHF) through the ring. If the ring is complete, the frame is received on its secondary port and the Master node resets its fail-period timer and continues normal operation.
PAGE 339
Figure 41. Example of Multiple Rings Connected by Single Switch Important FRRP Points FRRP provides a convergence time that can generally range between 150ms and 1500ms for Layer 2 networks. The Master node originates a high-speed frame that circulates around the ring. This frame, appropriately, sets up or breaks down the ring. ● ● ● ● ● ● ● ● ● ● The Master node transmits ring status check frames at specified intervals. You can run multiple physical rings on the same switch.
PAGE 340
Important FRRP Concepts The following table lists some important FRRP concepts. Concept Explanation Ring ID Each ring has a unique 8-bit ring ID through which the ring is identified (for example, FRRP 101 and FRRP 202, as shown in the illustration in Member VLAN Spanning Two Rings Connected by One Switch. Control VLAN Each ring has a unique Control VLAN through which tagged ring health frames (RHF) are sent. Control VLANs are used only for sending RHF, and cannot be used for any other purpose.
PAGE 341
● ● ● ● The control VLAN cannot have members that are not ring ports. If multiple rings share one or more member VLANs, they cannot share any links between them. Member VLANs across multiple rings are not supported in Master nodes. Each ring has only one Master node; all others are transit nodes. FRRP Configuration These are the tasks to configure FRRP.
PAGE 342
Interface: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 3. Assign the Primary and Secondary ports and the control VLAN for the ports on the ring. CONFIG-FRRP mode.
PAGE 343
VLAN ID: Identification number of the Control VLAN. 4. Configure a Transit node. CONFIG-FRRP mode. mode transit 5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id {range} VLAN-ID, Range: VLAN IDs for the ring’s Member VLANs. 6. Enable this FRRP group on this switch. CONFIG-FRRP mode. no disable Setting the FRRP Timers To set the FRRP timers, use the following command. NOTE: Set the Dead-Interval time 3 times the Hello-Interval.
PAGE 344
show frrp ring-id Ring ID: the range is from 1 to 255. ● Show the state of all FRRP groups. EXEC or EXEC PRIVELEGED mode. show frrp summary Ring ID: the range is from 1 to 255. Troubleshooting FRRP To troubleshoot FRRP, use the following information. Configuration Checks ● ● ● ● ● Each Control Ring must use a unique VLAN ID. Only two interfaces on a switch can be Members of the same control VLAN. There can be only one Master node for any FRRP group. You can configure FRRP on Layer 2 interfaces only.
PAGE 345
switchport no shutdown ! interface TenGigabitEthernet 2/31 no ip address switchport no shutdown ! interface Vlan 101 no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! interface Vlan 201 no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! protocol frrp 101 interface primary TenGigabitEthernet 2/14 secondary TenGigabitEthernet 2/31 controlvlan 101 member-vlan 201 mode transit no disable Example of R3 TRANSIT interface TenGigabitEthernet 3/14 no ip address switchport no shutdown ! interf
PAGE 346
Figure 42. FRRP Ring Connecting VLT Devices You can also configure an FRRP ring where both the VLT peers are connected to the FRRP ring and the VLTi acts as the primary interface for the FRRP Master and transit nodes. This active-active FRRP configuration blocks the FRRP ring on a per VLAN or VLAN group basis enabling the configuration to spawn across different set of VLANs.
PAGE 347
control VLAN, multiple member VLANS are configured (for example, M1 to M10) that carry the data traffic across the FRRP rings. The secondary port P2 is tagged to the control VLAN (V1). VLTi is implicitly tagged to the member VLANs when these VLANs are configured in the VLT peer. As a result of the VLT Node2 configuration on R2, the secondary interface P2 is blocked for the member VLANs (M11 to Mn). Following figure illustrated the FRRP Ring R1 topology: Figure 43.
PAGE 348
18 GARP VLAN Registration Protocol (GVRP) The generic attribute registration protocol (GARP) VLAN registration protocol (GVRP), defined by the IEEE 802.1q specification, is a Layer 2 network protocol that provides for automatic VLAN configuration of switches. GVRP-compliant switches use GARP to register and de-register attribute values, such as VLAN IDs, with each other.
PAGE 349
Configure GVRP To begin, enable GVRP. To facilitate GVRP communications, enable GVRP globally on each switch. Then, GVRP configuration is per interface on a switch-by-switch basis. Enable GVRP on each port that connects to a switch where you want GVRP information exchanged. In the following example, GVRP is configured on VLAN trunk ports. Figure 44. Global GVRP Configuration Example Basic GVRP configuration is a two-step process: 1. Enabling GVRP Globally 2.
PAGE 350
gvrp enable DellEMC(conf)#protocol gvrp DellEMC(config-gvrp)#no disable DellEMC(config-gvrp)#show config ! protocol gvrp no disable DellEMC(config-gvrp)# To inspect the global configuration, use the show gvrp brief command. Enabling GVRP on a Layer 2 Interface To enable GVRP on a Layer 2 interface, use the following command. ● Enable GVRP on a Layer 2 interface.
PAGE 351
no shutdown DellEMC(conf-if-te-1/21)# Configure a GARP Timer Set GARP timers to the same values on all devices that are exchanging information using GVRP. There are three GARP timer settings. ● Join — A GARP device reliably transmits Join messages to other devices by sending each Join message two times. To define the interval between the two sending operations of each Join message, use this parameter. The Dell EMC Networking OS default is 200ms.
PAGE 352
19 Internet Group Management Protocol (IGMP) Internet group management protocol (IGMP) is a Layer 3 multicast protocol that hosts use to join or leave a multicast group. Multicast is premised on identifying many hosts by a single destination IP address; hosts represented by the same IP address are a multicast group. Multicast routing protocols (such as protocol-independent multicast [PIM]) use the information in IGMP messages to discover which groups are active and to populate the multicast routing table.
PAGE 353
Figure 45. IGMP Messages in IP Packets Join a Multicast Group There are two ways that a host may join a multicast group: it may respond to a general query from its querier or it may send an unsolicited report to its querier. Responding to an IGMP Query The following describes how a host can join a multicast group. 1. One router on a subnet is elected as the querier. The querier periodically multicasts (to all-multicast-systems address 224.0.0.1) a general query to all hosts on the subnet. 2.
PAGE 354
IGMP Version 3 Conceptually, IGMP version 3 behaves the same as version 2. However, there are differences. ● Version 3 adds the ability to filter by multicast source, which helps multicast routing protocols avoid forwarding traffic to subnets where there are no interested receivers. ● To enable filtering, routers must keep track of more state information, that is, the list of sources that must be filtered.
PAGE 355
Joining and Filtering Groups and Sources The following illustration shows how multicast routers maintain the group and source information from unsolicited reports. 1. The first unsolicited report from the host indicates that it wants to receive traffic for group 224.1.1.1. 2. The host’s second report indicates that it is only interested in traffic from group 224.1.1.1, source 10.11.1.1. Include messages prevents traffic from all other sources in the group from reaching the subnet.
PAGE 356
Leaving and Staying in Groups The following illustration shows how multicast routers track and refresh state changes in response to group-and-specific and general queries. 1. Host 1 sends a message indicating it is leaving group 224.1.1.1 and that the included filter for 10.11.1.1 and 10.11.1.2 are no longer necessary. 2.
PAGE 357
● ● ● ● ● ● Adjusting Timers Preventing a Host from Joining a Group Enabling IGMP Immediate-Leave IGMP Snooping Fast Convergence after MSTP Topology Changes Designating a Multicast Router Interface Viewing IGMP Enabled Interfaces Interfaces that are enabled with PIM-SM are automatically enabled with IGMP. To view IGMP-enabled interfaces, use the following command. ● View IGMP-enabled IPv4 interfaces. EXEC Privilege mode show ip igmp interface ● View IGMP-enabled IPv6 interfaces.
PAGE 358
Viewing IGMP Groups To view both learned and statically configured IGMP groups, use the following command. ● View both learned and statically configured IGMP groups. EXEC Privilege mode show ip igmp groups show ipv6 mld groups DellEMC# show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface 225.1.1.1 TenGigabitEthernet 1/1 225.1.2.1 TenGigabitEthernet 1/1 Mode IGMPV2 IGMPV2 Uptime 00:11:19 00:10:19 Expires 00:01:50 00:01:50 Last Reporter 165.87.34.100 165.
PAGE 359
When the querier receives a leave message from a host, it sends a group-specific query to the subnet. If no response is received, it sends another. The amount of time that the querier waits to receive a response to the initial query before sending a second one is the last member query interval (LMQI). The switch waits one LMQI after the second query before removing the group from the state table. ● Adjust the period between queries.
PAGE 360
IGMP Snooping Implementation Information ● IGMP snooping on Dell EMC Networking OS uses IP multicast addresses not MAC addresses. ● IGMP snooping reacts to spanning tree protocol (STP) and multiple spanning tree protocol (MSTP) topology changes by sending a general query on the interface that transitions to the forwarding state. ● If IGMP snooping is enabled on a PIM-enabled VLAN interface, data packets using the router as an Layer 2 hop may be dropped.
PAGE 361
Disabling Multicast Flooding If the switch receives a multicast packet that has an IP address of a group it has not learned (unregistered frame), the switch floods that packet out of all ports on the VLAN. When you configure the no ip igmp snooping flood command, the system drops the packets immediately. The system does not forward the frames on mrouter ports, even if they are present. Disable Layer 3 multicast (no ip multicastrouting) in order to disable multicast flooding.
PAGE 362
Fast Convergence after MSTP Topology Changes When a port transitions to the Forwarding state as a result of an STP or MSTP topology change, Dell EMC Networking OS sends a general query out of all ports except the multicast router ports. The host sends a response to the general query and the forwarding database is updated without having to wait for the query interval to expire.
PAGE 363
Table 36.
PAGE 364
panel port IP on the peer box is initiated via management port only, if the management port is UP and management route is available.
PAGE 365
● TFTP is an exception to the preceding logic. ● For TFTP, data transfer is initiated on port 69, but the data transfer ports are chosen independently by the sender and receiver during initialization of the connection. The ports are chosen at random according to the parameters of the networking stack, typically from the range of temporary ports. ● If route lookup in EIS routing table succeeds, the application-specific packet count is incremented.
PAGE 366
Handling of Transit Traffic (Traffic Separation) This is forwarded traffic where destination IP is not an IP address configured in the switch. ● Packets received on the management port with destination on the front-end port is dropped. ● Packets received on the front-end port with destination on the management port is dropped. ● A separate drop counter is incremented for this case. This counter is viewed using the netstat command, like all other IP layer counters.
PAGE 367
This phenomenon occurs where traffic is originating from the switch. 1. Management Applications (Applications that are configured as management applications): The management port is an egress port for management applications. If the management port is down or the destination is not reachable through the management port (next hop ARP is not resolved, and so on), and if the destination is reachable through a data port, then the management application traffic is sent out through the front-end data port.
PAGE 368
EIS Behavior: If source TCP or UDP port matches an EIS management or a non-EIS management application and source IP address is management port IP address, management port is the preferred egress port selected based on route lookup in EIS table. If the management port is down or the route lookup fails, packets are dropped. If the source TCP/UDP port or source IP address does not match the management port IP address, a route lookup is done in the default routing table.
PAGE 369
Designating a Multicast Router Interface To designate an interface as a multicast router interface, use the following command. Dell EMC Networking OS also has the capability of listening in on the incoming IGMP general queries and designate those interfaces as the multicast router interface when the frames have a non-zero IP source address. All IGMP control packets and IP multicast data traffic originating from receivers is forwarded to multicast router interfaces.
PAGE 370
20 Interfaces This chapter describes interface types, both physical and logical, and how to configure them with Dell EMC Networking Operating System (OS). The system supports 10 Gigabit Ethernet and 40 Gigabit Ethernet interfaces. NOTE: Only Dell-qualified optics are supported on these interfaces. Non-Dell 40G optics are set to error-disabled state.
PAGE 371
• • • • • • • • • • • • • • • • • Defining Interface Range Macros Monitoring and Maintaining Interfaces Non Dell-Qualified Transceivers Splitting 40G Ports without Reload Splitting QSFP Ports to SFP+ Ports Converting a QSFP or QSFP+ Port to an SFP or SFP+ Port Configuring wavelength for 10–Gigabit SFP+ optics Link Dampening Link Bundle Monitoring Using Ethernet Pause Frames for Flow Control Configure the MTU Size on an Interface Port-Pipes Auto-Negotiation on Ethernet Interfaces View Advanced Interface Inf
PAGE 372
The following example shows the configuration and status information for one interface. DellEMC#show interfaces tengigabitethernet 1/1 TenGigabitEthernet 1/1 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:05:f3:6a Current address is 00:01:e8:05:f3:6a Pluggable media present, XFP type is 10GBASE-LR. Medium is MultiRate, Wavelength is 1310nm XFP receive power reading is -3.7685 Interface index is 67436603 Internet address is 65.113.24.
PAGE 373
interface TenGigabitEthernet 2/9 no ip address shutdown Resetting an Interface to its Factory Default State You can reset the configurations applied on an interface to its factory default state. To reset the configuration, perform the following steps: 1. View the configurations applied on an interface. INTERFACE mode show config DellEMC(conf-if-te-1/5)#show config ! interface TenGigabitEthernet 1/5 no ip address portmode hybrid switchport rate-interval 8 mac learning-limit 10 no-station-move no shutdown 2.
PAGE 374
Physical Interfaces The Management Ethernet interface is a single RJ-45 Fast Ethernet port on a switch. The interface provides dedicated management access to the system. Stack-unit interfaces support Layer 2 and Layer 3 traffic over the and 40-Gigabit Ethernet interfaces. These interfaces can also become part of virtual interfaces such as virtual local area networks (VLANs) or port channels. For more information about VLANs, refer to Bulk Configuration.
PAGE 375
Overview of Layer Modes On all systems running Dell EMC Networking OS, you can place physical interfaces, port channels, and VLANs in Layer 2 mode or Layer 3 mode. By default, VLANs are in Layer 2 mode. Table 41.
PAGE 376
Configuring Layer 3 (Network) Mode When you assign an IP address to a physical interface, you place it in Layer 3 mode. To enable Layer 3 mode on an individual interface, use the following commands. In all interface types except VLANs, the shutdown command prevents all traffic from passing through the interface. In VLANs, the shutdown command prevents Layer 3 traffic from passing through the interface. Layer 2 traffic is unaffected by the shutdown command.
PAGE 377
Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported Automatic recovery of an Err-disabled interface The Dell EMC Networking OS attempts to recover the interface from the Err-disabled state automatically based on the cause of the error.
PAGE 378
Whenever the Err-disable recovery timer is reconfigured, it will get effective only after the current timer expires. Following message is displayed after each Err-disable recovery timer configuration: DellEMC(conf)# errdisable recovery interval 30 New timer interval will be effective from the next timer instance only. Following is the sample steps to configure the recovery cause and the timer interval for automatic recovery of an interface.
PAGE 379
Management Interfaces The system supports the Management Ethernet interface as well as the standard interface on any port. You can use either method to connect to the system. Configuring Management Interfaces The dedicated Management interface provides management access to the system. You can configure this interface using the CLI, but the configuration options on this interface are limited.
PAGE 380
Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 If there are two RPMs on the system, configure each Management interface with a different IP address. Unless you configure the management route command, you can only access the Management interface from the local LAN.
PAGE 381
B - BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated, O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is 10.11.131.254 to network 0.0.0.0 Destination ----------*S 0.0.0.0/0 C 10.11.130.0/23 DellEMC# Gateway ------via 10.11.131.
PAGE 382
To configure, view, or delete a Loopback interface, use the following commands. ● Enter a number as the Loopback interface. CONFIGURATION mode interface loopback number The range is from 0 to 16383. ● View Loopback interface configurations. EXEC mode show interface loopback number ● Delete a Loopback interface. CONFIGURATION mode no interface loopback number Many of the commands supported on physical interfaces are also supported on a Loopback interface.
PAGE 383
● Port Channel Benefits ● Port Channel Implementation ● Configuration Tasks for Port Channel Interfaces Port Channel Definition and Standards Link aggregation is defined by IEEE 802.3ad as a method of grouping multiple physical interfaces into a single logical interface— a link aggregation group (LAG) or port channel. A LAG is “a group of links that appear to a MAC client as if they were a single link” according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a port channel interface.
PAGE 384
Port channels can contain a mix of 1G/10G/40G. The interface speed that the port channel uses is determined by the first port channel member that is physically up. Dell EMC Networking OS disables the interfaces that do not match the interface speed that the first channel member sets. That first interface may be either the interface that is physically brought up first or was physically operating when interfaces were added to the port channel.
PAGE 385
NOTE: To configure the MTU, use the mtu command from INTERFACE mode. To view the interface’s configuration, enter INTERFACE mode for that interface and use the show config command or from EXEC Privilege mode, use the show running-config interface interface command. When an interface is added to a port channel, Dell EMC Networking OS recalculates the hash algorithm. To add a physical interface to a port, use the following commands. 1. Add the interface to a port channel.
PAGE 386
interface that is part of that port channel. In the following example, interface 1/6 is part of port channel 5, which is in Layer 2 mode, and an error message appeared when an IP address was configured. DellEMC(conf-if-portch)#show config ! interface Port-channel 5 no ip address switchport channel-member TenGigabitEthernet 1/6 DellEMC(conf-if-portch)#int Te 1/6 DellEMC(conf-if)#ip address 10.56.4.4 /24 % Error: Port is part of a LAG Te 1/6.
PAGE 387
The default is 1. Example of Configuring the Minimum Oper Up Links in a Port Channel DellEMC#config t DellEMC(conf)#int po 1 DellEMC(conf-if-po-1)#minimum-links 5 DellEMC(conf-if-po-1)# Adding or Removing a Port Channel from a VLAN As with other interfaces, you can add Layer 2 port channel interfaces to VLANs. To add a port channel to a VLAN, place the port channel in Layer 2 mode (by using the switchport command).
PAGE 388
802.1QTagged: True Vlan membership: Q Vlans T 2-5,100,4010 DellEMC# Assigning an IP Address to a Port Channel You can assign an IP address to a port channel and use port channels in Layer 3 routing protocols. To assign an IP address, use the following command. ● Configure an IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] ○ ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in slash format (/24).
PAGE 389
● Change the default (0) to another algorithm and apply it to ECMP, LAG hashing, or a particular line card.
PAGE 390
The show configuration command is also available under Interface Range mode. This command allows you to display the running configuration only for interfaces that are part of interface range. You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as interface range fo 2/0-1,te 10/0,te 3/0,fo 0/0, this configuration is considered valid.
PAGE 391
Exclude a Smaller Port Range The following is an example show how the smaller of two port ranges is omitted in the interface-range prompt.
PAGE 392
Choosing an Interface-Range Macro To use an interface-range macro, use the following command. ● Selects the interfaces range to be configured using the values saved in a named interface-range macro. CONFIGURATION mode interface range macro name The following example shows how to change to the interface-range configuration mode using the interface-range macro named “test.
PAGE 393
Output underruns: Output throttles: m l T q - 0 0 0 pps 0 pps Change mode Page up Increase refresh interval Quit 0 0 c - Clear screen a - Page down t - Decrease refresh interval q DellEMC# Maintenance Using TDR The time domain reflectometer (TDR) is supported on all Dell EMC Networking switches. TDR is an assistance tool to resolve link issues that helps detect obvious open or short conditions within any of the four copper pairs.
PAGE 394
LineSpeed 40000 Mbit For information about which optics and transceivers are supported, contact your Dell representative. Splitting 40G Ports without Reload You can split 40G interfaces into 10G ports without reboot. You can also combine the split ports to create a 40G port without reload. ● On a device, fan-out profile constructs automatically with default 24 ports (0,8,16,24,32,36,40,44,48,52,56,60,64,68,72,76,80,84,88,92,100,108,116,124) .
PAGE 395
116 124 116 124 Dell# S6010-ON_1#show system stack-unit 1 quad-port-profile Configured fan out profile ports in stack-unit 1 Configured Activated 2 2 4 4 6 6 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 26 26 28 28 30 30 32 32 You can only split the 40G ports in the top row (odd numbered ports) on a 16X40G module. If you configure 4X10G on a 40G interface, the subsequent even numbered interface is removed and unavailable for use.
PAGE 396
1 1 1 1 1/15/1 1/15/2 1/15/3 1/15/4 QSFP QSFP QSFP QSFP 40GBASE-SR4 40GBASE-SR4 40GBASE-SR4 40GBASE-SR4 4829455N01XP 4829455N01XP 4829455N01XP 4829455N01XP Yes Yes Yes Yes Splitting QSFP Ports to SFP+ Ports The platform supports splitting a single 40G QSFP port into four 10G SFP+ ports using one of the supported breakout cables (for a list of supported cables, refer to the Installation Guide or the Release Notes).
PAGE 397
After you insert an SFP or SFP+ cable into a QSA connected to a 40 Gigabit port, Dell Networking OS assumes that all the four fanned-out 10 Gigabit ports have plugged-in SFP or SFP+ optical cables. However, the link UP event happens only for the first 10 Gigabit port and you can use only that port for data transfer. As a result, only the first fanned-out port is identified as the active 10 Gigabit port with a speed of 10G or 1G depending on whether you insert an SFP+ or SFP cable respectively.
PAGE 398
=================================== SFP+ 0 Temp High Alarm threshold SFP+ 0 Voltage High Alarm threshold SFP+ 0 Bias High Alarm threshold = 0.000C = 0.000V = 0.000mA NOTE: In the following show interfaces tengigbitethernet commands, the ports 1,2, and 3 are inactive and no physical SFP or SFP+ connection actually exists on these ports. However, Dell Networking OS still perceives these ports as valid and the output shows that pluggable media (optical cables) is inserted into these ports.
PAGE 399
SFP 0 Connector SFP 0 Transceiver Code SFP 0 Encoding ……………… = 0x23 = 0x08 0x00 0x00 0x00 0x00 0x00 0x00 0x00 = 0x00 Dell#show interfaces tengigabitethernet 0/7 transceiver SFP 0 Serial ID Base Fields SFP 0 Id = 0x0d SFP 0 Ext Id = 0x00 SFP 0 Connector = 0x23 SFP 0 Transceiver Code = 0x08 0x00 0x00 0x00 0x00 0x00 0x00 0x00 SFP 0 Encoding = 0x00 ……………… Dell#show interfaces tengigabitethernet 0/8 transceiver QSFP 0 Serial ID Base Fields QSFP 0 Id = 0x0d QSFP 0 Ext Id = 0x00 QSFP 0 Connector = 0x23 QSFP 0 Tr
PAGE 400
Hardware is DellEth, address is 90:b1:1c:f4:9a:fa Current address is 90:b1:1c:f4:9a:fa Pluggable media present, SFP+ type is 10GBASE-SX ………. LineSpeed 10000 Mbit Dell#show interfaces tengigabitethernet 0/3 tengigabitethernet 0/1 is up, line protocol is down Hardware is DellEth, address is 90:b1:1c:f4:9a:fa Current address is 90:b1:1c:f4:9a:fa Pluggable media present, SFP+ type is 10GBASE-SX ……….
PAGE 401
0 0 0 0 0 8 9 10 11 12 QSFP QSFP QSFP QSFP QSFP 4x10GBASE-CR1-3M 4x10GBASE-CR1-3M 4x10GBASE-CR1-3M 4x10GBASE-CR1-3M 40GBASE-SR4 APF12420031B3P APF12420031B3P APF12420031B3P APF12420031B3P Configuring wavelength for 10–Gigabit SFP+ optics You can set the wavelength for tunable 10–Gigabit SFP+ optics using the wavelength command. To set the wavelength, follow these steps: ● Enter the interface mode and set the wavelength. INTERFACE mode wavelength 1529.0 The wavelength range is from 1528.3 nm to 1568.
PAGE 402
● improves convergence times and stability throughout the network by isolating failures so that disturbances are not propagated. Important Points to Remember ● ● ● ● Link dampening is not supported on VLAN interfaces. Link dampening is disabled when the interface is configured for port monitoring. You can apply link dampening to Layer 2 and Layer 3 interfaces. You can configure link dampening on individual interfaces in a LAG.
PAGE 403
Figure 50. Interface State Change Consider an interface periodically flaps as shown above. Every time the interface goes down, a penalty (1024) is added. In the above example, during the first interface flap (flap 1), the penalty is added to 1024. And, the accumulated penalty will exponentially decay based on the set half-life, which is set as 10 seconds in the above example. During the second interface flap (flap 2), again the penalty (1024) is accumulated.
PAGE 404
Enabling Link Dampening To enable link dampening, use the following command. ● Enable link dampening. INTERFACE mode dampening To view the link dampening configuration on an interface, use the show config command. R1(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 ip address 10.10.19.1/24 dampening 1 2 3 4 no shutdown To view dampening information on all or specific dampened interfaces, use the show interfaces dampening command from EXEC Privilege mode.
PAGE 405
Configure MTU Size on an Interface In Dell EMC Networking OS, Maximum Transmission Unit (MTU) is defined as the entire Ethernet packet (Ethernet header + FCS + payload). The following table lists the range for each transmission media. Transmission Media MTU Range (in bytes) Ethernet 592-9216 = link MTU 576-9398 = IP MTU The IP MTU automatically configures.
PAGE 406
The globally assigned 48-bit Multicast address 01-80-C2-00-00-01 is used to send and receive pause frames. To allow fullduplex flow control, stations implementing the pause operation instruct the MAC to enable reception of frames with destination address equal to this multicast address. The PAUSE frame is defined by IEEE 802.3x and uses MAC Control frames to carry the PAUSE commands. Ethernet pause frames are supported on full duplex only.
PAGE 407
For example, for VLAN packets, if the IP MTU is 1400, the Link MTU must be no less than 1422: 1400-byte IP MTU + 22-byte VLAN Tag = 1422-byte link MTU The following table lists the various Layer 2 overheads found in Dell EMC Networking OS and the number of bytes. The MTU range is from 592 to 9216, with a default of 9216. IP MTU automatically configures. The following table lists the various Layer 2 overheads found in the Dell EMC Networking OS and the number of bytes. Table 42.
PAGE 408
Setting the Speed of Ethernet Interfaces To discover whether the remote and local interface requires manual speed synchronization, and to manually synchronize them if necessary, use the following command sequence. 1. Determine the local interface status. Refer to the following example. EXEC Privilege mode show interfaces [interface | stack—unit stack-unit-number] status 2. Determine the remote interface status.
PAGE 409
In the previous example, several ports display “Auto” in the Speed field. In the following example, the speed of port 1/1 is set to 100Mb and then its auto-negotiation is disabled.
PAGE 410
View Advanced Interface Information The following options have been implemented for the show [ip | running-config] interfaces commands for (only) stack-unit interfaces. When you use the configured keyword, only interfaces that have non-default configurations are displayed. Dummy stack-unit interfaces (created with the stack-unit command) are treated like any other physical interface.
PAGE 411
DellEMC(conf-if-te-1/1)#rate-interval 100 DellEMC#show interfaces TenGigabitEthernet 1/1 is down, line protocol is down Hardware is DellEMCEth, address is 00:01:e8:01:9e:d9 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 10000 Mbit ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1d23h45m Queueing strategy: fifo 0 packets input, 0 bytes Input 0 IP Packets, 0 Vlans 0 MPLS 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 o
PAGE 412
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 406 Multicasts, 0 Broadcasts, 2700 Unicasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 3106 packets, 226755 bytes, 0 underruns 133 64-byte pkts, 2973 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 406 Multicasts, 0 Broadcasts, 2700 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 150 seconds): Input 300.
PAGE 413
● IP FIB ● L2 ACL ● L2 FIB Clearing Interface Counters The counters in the show interfaces command are reset by the clear counters command. This command does not clear the counters any SNMP program captures. To clear the counters, use the following the command. ● Clear the counters used in the show interface commands for all VRRP groups, VLANs, and physical interfaces or selected ones. Without an interface specified, the command clears all interface counters.
PAGE 414
Table 43. Standard and Compressed Configurations Uncompressed Compressed ! ! interface TenGigabitEthernet 1/1 interface TenGigabitEthernet 1/1 no ip address no ip address switchport switchport shutdown shutdown ! ! interface TenGigabitEthernet 1/2 Interface group TenGigabitEthernet 1/2 – 4 , TenGigabitEthernet 1/10 no ip address shutdown shutdown ! interface TenGigabitEthernet 1/3 no ip address shutdown ! interface TenGigabitEthernet 1/34 ip address 2.1.1.
PAGE 415
Table 43. Standard and Compressed Configurations (continued) Uncompressed Compressed interface Vlan 5 tagged te 1/1 no ip address shutdown ! interface Vlan 100 no ip address no shutdown ! interface Vlan 1000 ip address 1.1.1.1/16 no shutdown Uncompressed config size – 52 lines write memory compressed The write memory compressed CLI will write the operating configuration to the startup-config file in the compressed mode.
PAGE 416
21 IPv4 Routing The Dell EMC Networking Operating System (OS) supports various IP addressing features. This chapter describes the basics of domain name service (DNS), address resolution protocol (ARP), and routing principles and their implementation in the Dell EMC Networking OS.
PAGE 417
IP Addresses Dell EMC Networking OS supports IP version 4 (as described in RFC 791), classful routing, and variable length subnet masks (VLSM). With VLSM, you can configure one network with different masks. Supernetting, which increases the number of subnets, is also supported. To subnet, you add a mask to the IP address to separate the network and host portions of the IP address.
PAGE 418
INTERFACE mode ip address ip-address mask [secondary] ● ip-address mask: the IP address must be in dotted decimal format (A.B.C.D). The mask must be in slash prefixlength format (/24). ● secondary: add the keyword secondary if the IP address is the interface’s backup IP address. You can configure up to eight secondary IP addresses. To view the configuration, use the show config command in INTERFACE mode or use the show ip interface command in EXEC privilege mode, as shown in the second example.
PAGE 419
S 6.1.2.7/32 S 6.1.2.8/32 S 6.1.2.9/32 S 6.1.2.10/32 S 6.1.2.11/32 S 6.1.2.12/32 S 6.1.2.13/32 S 6.1.2.14/32 S 6.1.2.15/32 S 6.1.2.16/32 S 6.1.2.17/32 S 11.1.1.0/24 Direct, Lo 0 --More-- via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.2, via 6.1.20.
PAGE 420
Configure Static Routes for the Management Interface When an IP address that a protocol uses and a static management route exists for the same prefix, the protocol route takes precedence over the static management route. To configure a static route for the management port, use the following command. ● Assign a static route to point to the management interface or forwarding router.
PAGE 421
occurs on the device. You can set the wait time to be 10 seconds or lower. If the device does not contain any BGP connections with the BGP neighbors across WAN links, you must set this interval to a higher value, depending on the complexity of your network and the configuration attributes. To configure the duration for which the device waits for the ACK packet to be sent from the requesting host to establish the TCP connection, perform the following steps: 1.
PAGE 422
ip name-server ip-address [ip-address2 ... ip-address6] The order you entered the servers determines the order of their use. To view current bindings, use the show hosts command. DellEMC>show host Default domain is force10networks.com Name/address lookup uses domain service Name servers are not set Host Flags TTL Type Address -------- ----- ------- ------ks (perm, OK) - IP 2.2.2.2 patch1 (perm, OK) - IP 192.68.69.2 tomm-3 (perm, OK) - IP 192.68.99.2 gxr (perm, OK) - IP 192.71.18.2 f00-3 (perm, OK) - IP 192.
PAGE 423
To keep the default setting for these parameters, press the ENTER key. The following text is example output of DNS using the traceroute command. DellEMC#traceroute www.force10networks.com Translating "www.force10networks.com"...domain server (10.11.0.1) [OK] Type Ctrl-C to abort. ---------------------------------------------------------------------Tracing the route to www.force10networks.com (10.11.84.
PAGE 424
○ ip-address: IP address in dotted decimal format (A.B.C.D). ○ mac-address: MAC address in nnnn.nnnn.nnnn format. ○ interface: enter the interface type slot/port information. These entries do not age and can only be removed manually. To remove a static ARP entry, use the no arp ip-address command. To view the static entries in the ARP cache, use the show arp static command in EXEC privilege mode.
PAGE 425
● inform switches of their presence on a port so that packets can be forwarded ● update the ARP table of other nodes on the network in case of an address change In the request, the host uses its own IP address in the Sender Protocol Address and Target Protocol Address fields. Enabling ARP Learning via Gratuitous ARP To enable ARP learning via gratuitous ARP, use the following command. ● Enable ARP learning via gratuitous ARP.
PAGE 426
Configuring ARP Retries You can configure the number of ARP retries. The default backoff interval remains at 20 seconds. To set and display ARP retries, use the following commands. ● Set the number of ARP retries. CONFIGURATION mode arp retries number The default is 5. The range is from 1 to 20. ● Set the exponential timer for resending unresolved ARPs. CONFIGURATION mode arp backoff-time The default is 30. The range is from 1 to 3600. ● Display all ARP entries learned via gratuitous ARP.
PAGE 427
ICMP Redirects When a host sends a packet to a destination, it sends the packet to the configured default gateway. If the gateway router finds that a better route is available through a different router in the same network, that is, the same data link, the gateway router sends the source host an ICMP redirect message with the better route. The gateway router routes the packet to its destination and the host sends subsequent packets to that particular destination through the correct router.
PAGE 428
UDP Helper User datagram protocol (UDP) helper allows you to direct the forwarding IP/UDP broadcast traffic by creating special broadcast addresses and rewriting the destination IP address of packets to match those addresses. Configure UDP Helper To configure Dell EMC Networking OS to direct UDP broadcast, enable UDP helper and specify the UDP ports for which traffic is forwarded.
PAGE 429
ip address 1.1.0.1/24 ip udp-broadcast-address 1.1.255.255 untagged TenGigabitEthernet 1/2 no shutdown To view the configured broadcast address for an interface, use show interfaces command. DellEMC#show interfaces vlan 100 Vlan 100 is up, line protocol is down Address is 00:01:e8:0d:b9:7a, Current address is 00:01:e8:0d:b9:7a Interface index is 1107787876 Internet address is 1.1.0.1/24 IP UDP-Broadcast address is 1.1.255.
PAGE 430
Figure 54. UDP Helper with Broadcast-All Addresses UDP Helper with Subnet Broadcast Addresses When the destination IP address of an incoming packet matches the subnet broadcast address of any interface, the system changes the address to the configured broadcast address and sends it to matching interface. In the following illustration, Packet 1 has the destination IP address 1.1.1.255, which matches the subnet broadcast address of VLAN 101.
PAGE 431
Figure 56. UDP Helper with Configured Broadcast Addresses UDP Helper with No Configured Broadcast Addresses The following describes UDP helper with no broadcast addresses configured. ● If the incoming packet has a broadcast destination IP address, the unaltered packet is routed to all Layer 3 interfaces. ● If the Incoming packet has a destination IP address that matches the subnet broadcast address of any interface, the unaltered packet is routed to the matching interfaces.
PAGE 432
22 IPv6 Routing Internet protocol version 6 (IPv6) routing is the successor to IPv4. Due to the rapid growth in internet users and IP addresses, IPv4 is reaching its maximum usage. IPv6 will eventually replace IPv4 usage to allow for the constant expansion. This chapter provides a brief description of the differences between IPv4 and IPv6, and the Dell EMC Networking support of IPv6. This chapter is not intended to be a comprehensive description of IPv6.
PAGE 433
● Prefix Renumbering — Useful in transparent renumbering of hosts in the network when an organization changes its service provider. NOTE: As an alternative to stateless autoconfiguration, network hosts can obtain their IPv6 addresses using the dynamic host control protocol (DHCP) servers via stateful auto-configuration. NOTE: Dell EMC Networking OS provides the flexibility to add prefixes on Router Advertisements (RA) to advertise responses to Router Solicitations (RS).
PAGE 434
● Partition will take effect only after the switch reboot. During the reboot Dell EMC Networking OS reads the partition configuration from NVRAM and uses the same for partitioning the LPM. ● A command has been introduced to partition the LPM to support provisioning of IPv6 /65 to /128 route prefixes. To support /65 – /128 IPv6 route prefix entries, Dell EMC Networking OS needs to be programmed with /65 - /128 bit IPv6 support. The number of entries as well needs to be explicitly programmed.
PAGE 435
Version (4 bits) The Version field always contains the number 6, referring to the packet’s IP version. Traffic Class (8 bits) The Traffic Class field deals with any data that needs special handling. These bits define the packet priority and are defined by the packet Source. Sending and forwarding routers use this field to identify different IPv6 classes and priorities. Routers understand the priority settings and handle them appropriately during conditions of congestion.
PAGE 436
Hop Limit (8 bits) The Hop Limit field shows the number of hops remaining for packet processing. In IPv4, this is known as the Time to Live (TTL) field and uses seconds rather than hops. Each time the packet moves through a forwarding router, this field decrements by 1. If a router receives a packet with a Hop Limit of 1, it decrements it to 0 (zero). The router discards the packet and sends an ICMPv6 message back to the sending router indicating that the Hop Limit was exceeded in transit.
PAGE 437
11 Discard the packet and send an ICMP Parameter Problem, Code 2 message to the packet’s Source IP Address only if the Destination IP Address is not a multicast address. The second byte contains the Option Data Length. The third byte specifies whether the information can change en route to the destination. The value is 1 if it can change; the value is 0 if it cannot change.
PAGE 438
Implementing IPv6 with Dell EMC Networking OS Dell EMC Networking OS supports both IPv4 and IPv6 and both may be used simultaneously in your system. The following table lists the Dell EMC Networking OS version in which an IPv6 feature became available for each platform. The sections following the table give greater detail about the feature. Table 44.
PAGE 439
Table 44. Dell EMC Networking OS versions and supported platforms with IPv6 support (continued) Feature and Functionality Dell EMC Networking OS Release Introduction Documentation and Chapter Location S6000 IPv6 IS-IS in the Dell EMC Networking OS Command Line Reference Guide. OSPF for IPv6 (OSPFv3) 8.3.11 Equal Cost Multipath for IPv6 8.3.11 OSPFv3 in the Dell EMC Networking OS Command Line Reference Guide. IPv6 Services and Management Telnet client over IPv6 (outbound Telnet) 8.3.
PAGE 440
Path MTU discovery The size of the packet that can be sent across each hop in the network path without being fragmented is called the path maximum transmission unit (PMTU). The PMTU value might differ for the same route between two devices, mainly over a public network, depending on the network load and speed, and it is not a consistent value. The MTU size can also be different for various types of traffic sent from one host to the same endpoint.
PAGE 441
Figure 59. NDP Router Redirect IPv6 Neighbor Discovery of MTU Packets You can set the MTU advertised through the RA packets to incoming routers, without altering the actual MTU setting on the interface. The ipv6 nd mtu command sets the value advertised to routers. It does not set the actual MTU rate. For example, if you set ipv6 nd mtu to 1280, the interface still passes 1500-byte packets, if that is what is set with the mtu command.
PAGE 442
resolution DellEMC(conf-if-te-1/1)#ipv6 nd dns-server 1000::1 1 Debugging IPv6 RDNSS Information Sent to the Host To verify that the IPv6 RDNSS information sent to the host is configured correctly, use the debug ipv6 nd command in EXEC Privilege mode. Example of Debugging IPv6 RDNSS Information Sent to the Host The following example debugs IPv6 RDNSS information sent to the host.
PAGE 443
IPv6 hop limit for originated packets ND dns-server address is 1000::1 with ND dns-server address is 3000::1 with ND dns-server address is 2000::1 with IP unicast RPF check is not supported is 64 lifetime of 1 seconds lifetime of 1 seconds lifetime of 0 seconds To display IPv6 RDNSS information, use the show configuration command in INTERFACE CONFIG mode. DellEMC(conf-if-te-1/1)#show configuration The following example uses the show configuration command to display IPv6 RDNSS information.
PAGE 444
CONFIGURATION mode cam-acl { ipv6acl } When not selecting the default option, enter all of the profiles listed and a range for each. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. ● Show the current CAM settings. EXEC mode or EXEC Privilege mode show cam-acl ● Provides information on FP groups allocated for the egress acl. CONFIGURATION mode show cam-acl-egress Allocate at least one group for L2ACL and IPv4 ACL. The total number of groups is 4.
PAGE 445
○ forwarding router: forwarding router’s address ○ tag: route tag Enter the keyword interface then the type of interface and slot/port information: ○ ○ ○ ○ ○ ○ For For For For For For a a a a a a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 446
mld mroute neighbors ospf pim prefix-list route rpf DellEMC# MLD information IPv6 multicast-routing table IPv6 neighbor information OSPF information PIM V6 information List IPv6 prefix lists IPv6 routing information RPF table Displaying an IPv6 Interface Information To view the IPv6 configuration for a specific interface, use the following command. ● Show the currently running configuration for the specified interface.
PAGE 447
The following keywords are available: ○ To display information about a network, enter ipv6 address (X:X:X:X::X). ○ To display information about a host, enter hostname. ○ To display information about all IPv6 routes (including non-active routes), enter all. ○ To display information about all connected IPv6 routes, enter connected. ○ To display information about brief summary of all IPv6 routes, enter summary. ○ To display information about Border Gateway Protocol (BGP) routes, enter bgp.
PAGE 448
Showing the Running-Configuration for an Interface To view the configuration for any interface, use the following command. ● Show the currently running configuration for the specified interface. EXEC mode show running-config interface type {slot/port} Enter the keyword interface then the type of interface and slot/port information: ○ For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 449
Configuring IPv6 RA Guard The IPv6 Router Advertisement (RA) guard allows you to block or reject the unwanted router advertisement guard messages that arrive at the network device platform. To configure the IPv6 RA guard, perform the following steps: 1. Configure the terminal to enter the Global Configuration mode. EXEC Privilege mode configure terminal 2. Enable the IPv6 RA guard. CONFIGURATION mode ipv6 nd ra-guard enable 3. Create the policy.
PAGE 450
reachable—time value The reachability time range is from 0 to 3,600,000 milliseconds. 14. Set the advertised retransmission time. POLICY LIST CONFIGURATION mode retrans—timer value The retransmission time range is from 100 to 4,294,967,295 milliseconds. 15. Display the configurations applied on the RA guard policy mode.
PAGE 451
EXEC Privilege mode debug ipv6 nd ra-guard [interface slot/port | count value] The count range is from 1 to 65534. The default is infinity. For a complete listing of all commands related to IPv6 RA Guard, see the Dell EMC Networking OS Command Line Reference Guide.
PAGE 452
23 iSCSI Optimization This chapter describes how to configure internet small computer system interface (iSCSI) optimization, which enables qualityof-service (QoS) treatment for iSCSI traffic.
PAGE 453
NOTE: After a switch is reloaded, powercycled, or upgraded, the system may display the ACL_AGENT-3ISCSI_OPT_MAX_SESS_LIMIT_REACHED: Monitored iSCSI sessions reached maximum limit log message. This cannot be inferred as the maximum supported iSCSI sessions are reached. Also, number of iSCSI sessions displayed on the system may show any number equal to or less than the maximum.
PAGE 454
Application of Quality of Service to iSCSI Traffic Flows You can configure iSCSI CoS mode. This mode controls whether CoS (dot1p priority) queue assignment and/or packet marking is performed on iSCSI traffic. When you enable iSCSI CoS mode, the CoS policy is applied to iSCSI traffic. When you disable iSCSI CoS mode, iSCSI sessions and connections are still detected and displayed in the status tables, but no CoS policy is applied to iSCSI traffic.
PAGE 455
Detection and Auto-Configuration for Dell EqualLogic Arrays The iSCSI optimization feature includes auto-provisioning support with the ability to detect directly connected Dell EqualLogic storage arrays and automatically reconfigure the switch to enhance storage traffic flows. The switch uses the link layer discovery protocol (LLDP) to discover Dell EqualLogic devices on the network. LLDP is enabled by default. For more information about LLDP, refer to Link Layer Discovery Protocol (LLDP).
PAGE 456
● Additional updates to connections (including aging updates) that are learnt on VLT lag members are synced to the peer. ● When receiving an iSCSI login request on a non-VLT interface followed by a response from a VLT interface, the session is not synced since it is initially learnt on a non-VLT interface through the request packet. ● The peer generates a new connection log that sees the login response packet.
PAGE 457
Table 45. iSCSI Optimization Defaults (continued) Parameter Default Value iSCSI optimization target ports iSCSI well-known ports 3260 and 860 are configured as default (with no IP address or name) but can be removed as any other configured target. iSCSI session monitoring Disabled. The CAM allocation for iSCSI is set to zero (0). iSCSI Optimization Prerequisites The following are iSCSI optimization prerequisites. ● iSCSI optimization requires LLDP on the switch.
PAGE 458
CONFIGURATION mode [no] iscsi target port tcp-port-1 [tcp-port-2...tcp-port-16] [ip-address address] ● tcp-port-n is the TCP port number or a list of TCP port numbers on which the iSCSI target listens to requests. You can configure up to 16 target TCP ports on the switch in one command or multiple commands. The default is 860, 3260. Separate port numbers with a comma.
PAGE 459
Displaying iSCSI Optimization Information To display information on iSCSI optimization, use the following show commands. ● Display the currently configured iSCSI settings. show iscsi ● Display information on active iSCSI sessions on the switch. show iscsi sessions ● Display detailed information on active iSCSI sessions on the switch . To display detailed information on specified iSCSI session, enter the session’s iSCSI ID.
PAGE 460
Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-2c Up Time:00:00:01:28(DD:HH:MM:SS) Time for aging out:00:00:09:34(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.53 33432 10.10.0.
PAGE 461
24 Intermediate System to Intermediate System The intermediate system to intermediate system (IS-IS) protocol that uses a shortest-path-first algorithm. Dell EMC Networking supports both IPv4 and IPv6 versions of IS-IS.
PAGE 462
Figure 61. ISO Address Format Multi-Topology IS-IS Multi-topology IS-IS (MT IS-IS) allows you to create multiple IS-IS topologies on a single router with separate databases. Use this feature to place a virtual physical topology into logical routing domains, which can each support different routing and security policies. All routers on a LAN or point-to-point must have at least one common supported topology when operating in Multi-Topology ISIS mode.
PAGE 463
Graceful Restart Graceful restart is a protocol-based mechanism that preserves the forwarding table of the restarting router and its neighbors for a specified period to minimize the loss of packets. A graceful-restart router does not immediately assume that a neighbor is permanently down and so does not trigger a topology change. Normally, when an IS-IS router is restarted, temporary disruption of routing occurs due to events in both the restarting router and the neighbors of the restarting router.
PAGE 464
● ● ● ● Processes IPv6 information received in the PDUs. Computes routes to IPv6 destinations. Downloads IPv6 routes to the RTM for installing in the FIB. Accepts external IPv6 information and advertises this information in the PDUs. The following table lists the default IS-IS values. Table 46.
PAGE 465
In IS-IS, neighbors form adjacencies only when they are same IS type. For example, a Level 1 router never forms an adjacency with a Level 2 router. A Level 1-2 router forms Level 1 adjacencies with a neighboring Level 1 router and forms Level 2 adjacencies with a neighboring Level 2 router. NOTE: Even though you enable IS-IS globally, enable the IS-IS process on an interface for the IS-IS process to exchange protocol information and form adjacencies. To configure IS-IS globally, use the following commands.
PAGE 466
To view the IS-IS configuration, enter the show isis protocol command in EXEC Privilege mode or the show config command in ROUTER ISIS mode. DellEMC#show isis protocol IS-IS Router: System Id: EEEE.EEEE.EEEE IS-Type: level-1-2 Manual area address(es): 47.0004.004d.0001 Routing for area address(es): 21.2223.2425.2627.2829.3031.3233 47.0004.004d.
PAGE 467
2. Exclude this router from other router’s SPF calculations. ROUTER ISIS AF IPV6 mode set-overload-bit 3. Set the minimum interval between SPF calculations. ROUTER ISIS AF IPV6 mode spf-interval [level-l | level-2 | interval] [initial_wait_interval [second_wait_interval]] Use this command for IPv6 route computation only when you enable multi-topology. If using single-topology mode, to apply to both IPv4 and IPv6 route computations, use the spf-interval command in CONFIG ROUTER ISIS mode. 4.
PAGE 468
graceful-restart t3 {adjacency | manual seconds} ○ adjacency: the restarting router receives the remaining time value from its peer and adjusts its T3 value so if user has configured this option. ○ manual: allows you to specify a fixed value that the restarting router should use. The range is from 50 to 120 seconds. The default is 30 seconds. NOTE: If this timer expires before the synchronization has completed, the restarting router sends the overload bit in the LSP.
PAGE 469
Restart Capable Neighbors: 2, In Start: 0, In Restart: 0 DellEMC# Changing LSP Attributes IS-IS routers flood link state PDUs (LSPs) to exchange routing information. LSP attributes include the generation interval, maximum transmission unit (MTU) or size, and the refresh interval. You can modify the LSP attribute defaults, but it is not necessary. To change the defaults, use any or all of the following commands. ● Set interval between LSP generation.
PAGE 470
example, if you configure the metric as narrow, and a link state PDU (LSP) with wide metrics is received, the route is not installed. Dell EMC Networking OS supports the following IS-IS metric styles. Table 47. Metric Styles Metric Style Characteristics Cost Range Supported on IS-IS Interfaces narrow Sends and accepts narrow or old TLVs (Type, Length, Value). 0 to 63 wide Sends and accepts wide or new TLVs. 0 to 16777215 transition Sends both wide (new) and narrow (old) TLVs.
PAGE 471
○ default-metric: the range is from 0 to 63 if the metric-style is narrow, narrow-transition, or transition. The range is from 0 to 16777215 if the metric style is wide or wide transition. ● Assign a metric for an IPv6 link or interface. INTERFACE mode isis ipv6 metric default-metric [level-1 | level-2] ○ default-metric: the range is from 0 to 63 for narrow and transition metric styles. The range is from 0 to 16777215 for wide metric styles. The default is 10. The default level is level-1.
PAGE 472
The default is Level 1-2 router. When the IS-type is Level 1-2, the software maintains two Link State databases, one for each level. To view the Link State databases, use the show isis database command. DellEMC#show isis database IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum B233.00-00 0x00000003 0x07BF eljefe.00-00 * 0x00000009 0xF76A eljefe.01-00 * 0x00000001 0x68DF eljefe.02-00 * 0x00000001 0x2E7F Force10.
PAGE 473
○ For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● Apply a configured prefix list to all outgoing IPv4 IS-IS routes. ROUTER ISIS mode distribute-list prefix-list-name out [bgp as-number | connected | ospf process-id | rip | static] You can configure one of the optional parameters: ○ connected: for directly connected routes. ○ ospf process-id: for OSPF routes only. ○ rip: for RIP routes only. ○ static: for user-configured routes. ○ bgp: for BGP routes only.
PAGE 474
Redistributing IPv4 Routes In addition to filtering routes, you can add routes from other routing instances or protocols to the IS-IS process. With the redistribute command syntax, you can include BGP, OSPF, RIP, static, or directly connected routes in the IS-IS process. NOTE: Do not route iBGP routes to IS-IS unless there are route-maps associated with the IS-IS redistribution. To add routes from other routing instances or protocols, use the following commands.
PAGE 475
redistribute ospf process-id [level-1| level-1-2 | level-2] [metric value] [match external {1 | 2} | match internal] [metric-type {external | internal}] [route-map mapname] Configure the following parameters: ○ ○ ○ ○ ○ ○ ○ ○ process-id: the range is from 1 to 65535. level-1, level-1-2, or level-2: assign all redistributed routes to a level. The default is level-2. metric value: the range is from 0 to 16777215. The default is 0. metric value: the range is from 0 to 16777215. The default is 0.
PAGE 476
no set-overload-bit When the bit is set, a 1 is placed in the OL column in the show isis database command output. The overload bit is set in both the Level-1 and Level-2 database because the IS type for the router is Level-1-2. DellEMC#show isis database IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum B233.00-00 0x00000003 0x07BF eljefe.00-00 * 0x0000000A 0xF963 eljefe.01-00 * 0x00000001 0x68DF eljefe.02-00 * 0x00000001 0x2E7F Force10.
PAGE 477
Dell EMC Networking OS displays debug messages on the console. To view which debugging commands are enabled, use the show debugging command in EXEC Privilege mode. To disable a specific debug command, enter the keyword no then the debug command. For example, to disable debugging of IS-IS updates, use the no debug isis updates-packets command. To disable all IS-IS debugging, use the no debug isis command. To disable all debugging, use the undebug all command.
PAGE 478
Table 48. Metric Value When the Metric Style Changes (continued) Beginning Metric Style Final Metric Style Resulting IS-IS Metric Value wide transition truncated value (the truncated value appears in the LSP only). The original isis metric value is displayed in the show config and show runningconfig commands and is used if you change back to transition metric style. NOTE: A truncated value is a value that is higher than 63, but set back to 63 because the higher value is not supported.
PAGE 479
Table 49. Metric Value when the Metric Style Changes Multiple Times (continued) Beginning Metric Style Next Metric Style Resulting Metric Value Next Metric Style Final Metric Value wide transition transition truncated value wide transition original value is recovered wide transition truncated value narrow default value (10). A message is sent to the logging buffer wide transition transition truncated value narrow transition default value (10).
PAGE 480
You can copy and paste from these examples to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes. NOTE: Whenever you make IS-IS configuration changes, clear the IS-IS process (re-started) using the clear isis command. The clear isis command must include the tag for the ISIS process. The following example shows the response from the router: DellEMC#clear isis * % ISIS not enabled.
PAGE 481
metric-style wide level-2 net 34.0000.0000.AAAA.00 DellEMC(conf-router_isis)# IS-IS Sample Configuration — Multi-topology DellEMC(conf-if-te-3/17)#show config ! interface TenGigabitEthernet 3/17 ipv6 address 24:3::1/76 ipv6 router isis no shutdown DellEMC(conf-if-te-3/17)# DellEMC(conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.
PAGE 482
25 In-Service Software Upgrade This chapter deals with In-Service Software Upgrade (ISSU) and its dependencies. Topics: • • • • • • • • • ISSU Introduction Fastboot 2.0 (Zero Loss Upgrade) L2 ISSU L3 ISSU CoPP Mirroring flow control packets PFC QoS Tunnel Configuration ISSU Introduction In-service software upgrades (ISSU), also known as warmboot or fastboot 2.0, allow Dell EMC Networking to address software bugs and add new features to switches and routers without interrupting network availability.
PAGE 483
L2 ISSU This section deals with L2 ISSU related information. The following changes are required by ISSU for L2: LACP Long Timeout If there is a LACP protocol running on an interface, the user needs to have the LACP long timeout configured, if LACP short timeout is configured, ISSU will not take place. Spanning Tree When spanning tree is enabled, user needs to have BPDU guard configured in the interfaces.
PAGE 484
The user will need to configure the boot-type to warmboot under the reload-type configuration mode. Warmboot is a system reload technique where the NPU will not restart. Only the CPU is restarted to bring up the upgraded software. Software upgrade ISSU, is the typical use case for warmboot. Since BCM chip is already up and running while the software is restarted, there should not be any traffic outage during warmboot.
PAGE 485
26 Link Aggregation Control Protocol (LACP) A link aggregation group (LAG), referred to as a port channel by the Dell EMC Networking OS, can provide both load-sharing and port redundancy across line cards. You can enable LAGs as static or dynamic.
PAGE 486
NOTE: There is no configuration on the interface because that condition is required for an interface to be part of a LAG. ● You can configure link dampening on individual members of a LAG. LACP Modes Dell EMC Networking OS provides three modes for configuration of LACP — Off, Active, and Passive. ● Off — In this state, an interface is not capable of being part of a dynamic LAG. LACP does not run on any port that is configured to be in this state.
PAGE 487
● ● ● ● Configuring the LAG Interfaces as Dynamic Setting the LACP Long Timeout Monitoring and Debugging LACP Configuring Shared LAG State Tracking Creating a LAG To create a dynamic port channel (LAG), use the following command. First you define the LAG and then the LAG interfaces. ● Create a dynamic port channel (LAG). CONFIGURATION mode interface port-channel ● Create a dynamic port channel (LAG).
PAGE 488
Setting the LACP Long Timeout PDUs are exchanged between port channel (LAG) interfaces to maintain LACP sessions. PDUs are transmitted at either a slow or fast transmission rate, depending upon the LACP timeout value. The timeout value is the amount of time that a LAG interface waits for a PDU from the remote system before bringing the LACP session down. The default timeout value is 1 second. You can configure the default timeout value to be 30 seconds.
PAGE 489
Figure 63. Shared LAG State Tracking To avoid packet loss, redirect traffic through the next lowest-cost link (R3 to R4). Dell EMC Networking OS has the ability to bring LAG 2 down if LAG 1 fails, so that traffic can be redirected. This redirection is what is meant by shared LAG state tracking. To achieve this functionality, you must group LAG 1 and LAG 2 into a single entity, called a failover group.
PAGE 490
Figure 64. Configuring Shared LAG State Tracking The following are shared LAG state tracking console messages: ● 2d1h45m: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 1 ● 2d1h45m: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 2 To view the status of a failover group member, use the show interface port-channel command.
PAGE 491
LACP Basic Configuration Example The screenshots in this section are based on the following example topology. Two routers are named ALPHA and BRAVO, and their hostname prompts reflect those names. Figure 65. LACP Basic Configuration Example Configure a LAG on ALPHA The following example creates a LAG on ALPHA.
PAGE 492
0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics 136 packets, 16718 bytes, 0 underruns 0 64-byte pkts, 15 over 64-byte pkts, 121 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 136 Multicasts, 0 Broadcasts, 0 Unicasts 0 Vlans, 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec,0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec,0 packets/sec, 0.
PAGE 493
Figure 67.
PAGE 494
Figure 68.
PAGE 495
Bravo(conf-if-po-10)#switch Bravo(conf-if-po-10)#no shut Bravo(conf-if-po-10)#show config ! interface Port-channel 10 no ip address switchport no shutdown ! Bravo(conf-if-po-10)#exit Bravo(conf)#int tengig 3/21 Bravo(conf)#no ip address Bravo(conf)#no switchport Bravo(conf)#shutdown Bravo(conf-if-te-3/21)#port-channel-protocol lacp Bravo(conf-if-te-3/21-lacp)#port-channel 10 mode active Bravo(conf-if-te-3/21-lacp)#no shut Bravo(conf-if-te-3/21)#end ! interface TenGigabitEthernet 3/21 no ip address ! port-ch
PAGE 496
Figure 69.
PAGE 497
Figure 70.
PAGE 498
Figure 71. Inspecting the LAG Status Using the show lacp command The point-to-point protocol (PPP) is a connection-oriented protocol that enables layer two links over various different physical layer connections. It is supported on both synchronous and asynchronous lines, and can operate in Half-Duplex or Full-Duplex mode. It was designed to carry IP traffic but is general enough to allow any type of network layer datagram to be sent over a PPP connection.
PAGE 499
27 Layer 2 This chapter describes the Layer 2 features supported on the device. Topics: • • • • • Manage the MAC Address Table MAC Learning Limit NIC Teaming Configure Redundant Pairs Far-End Failure Detection Manage the MAC Address Table You can perform the following management tasks in the MAC address table.
PAGE 500
Configuring a Static MAC Address A static entry is one that is not subject to aging. Enter static entries manually. To create a static MAC address entry, use the following command. ● Create a static MAC address entry in the MAC address table. CONFIGURATION mode mac-address-table static Displaying the MAC Address Table To display the MAC address table, use the following command. ● Display the contents of the MAC address table.
PAGE 501
Setting the MAC Learning Limit To set a MAC learning limit on an interface, use the following command. ● Specify the number of MAC addresses that the system can learn off a Layer 2 interface. INTERFACE mode mac learning-limit address_limit Three options are available with the mac learning-limit command: ○ dynamic ○ no-station-move ○ station-move NOTE: An SNMP trap is available for mac learning-limit station-move. No other SNMP traps are available for MAC Learning Limit, including limit violations.
PAGE 502
mac learning-limit no-station-move The no-station-move option, also known as “sticky MAC,” provides additional port security by preventing a station move. When you configure this option, the first entry in the table is maintained instead of creating an entry on the new interface. nostation-move is the default behavior. Entries created before you set this option are not affected. To display a list of all interfaces with a MAC learning limit, use the following command.
PAGE 503
station-move-violation shutdown-both ● Display a list of all of the interfaces configured with MAC learning limit or station move violation. CONFIGURATION mode show mac learning-limit violate-action NOTE: When the MAC learning limit (MLL) is configured as no-station-move, the MLL will be processed as static entries internally. For static entries, the MAC address will be installed in all port-pipes, irrespective of the VLAN membership.
PAGE 504
CONFIGURATION mode mac port-security NIC Teaming NIC teaming is a feature that allows multiple network interface cards in a server to be represented by one MAC address and one IP address in order to provide transparent redundancy, balancing, and to fully utilize network adapter resources. The following illustration shows a topology where two NICs have been teamed together.
PAGE 505
Figure 73. Configuring the mac-address-table station-move refresh-arp Command Configure Redundant Pairs Networks that employ switches that do not support the spanning tree protocol (STP) — for example, networks with digital subscriber line access multiplexers (DSLAM) — cannot have redundant links between switches because they create switching loops (as shown in the following illustration).
PAGE 506
Figure 74. Configuring Redundant Layer 2 Pairs without Spanning Tree You configure a redundant pair by assigning a backup interface to a primary interface with the switchport backup interface command. Initially, the primary interface is active and transmits traffic and the backup interface remains down. If the primary fails for any reason, the backup transitions to an active Up state. If the primary interface fails and later comes back up, it remains as the backup interface for the redundant pair.
PAGE 507
As shown in the above illustration, interface 3/41 is a backup interface for 3/42, and 3/42 is in the Down state. If 3/41 fails, 3/42 transitions to the Up state, which makes the backup link active. A message similar to the following message appears whenever you configure a backup port.
PAGE 508
Apr 9 00:16:29: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Te 1/2 DellEMC(conf-if-po-1)# Far-End Failure Detection Far-end failure detection (FEFD) is a protocol that senses remote data link errors in a network. FEFD responds by sending a unidirectional report that triggers an echoed response after a specified time interval. You can enable FEFD globally or locally on an interface basis.
PAGE 509
3. When the local interface receives the echoed packet from the remote end, the local interface transitions to the Bi-directional state. 4. If the FEFD enabled system is configured to use FEFD in Normal mode and neighboring echoes are not received after three intervals, (you can set each interval can be set between 3 and 300 seconds) the state changes to unknown. 5.
PAGE 510
fefd-global {interval | mode} To display information about the state of each interface, use the show fefd command in EXEC privilege mode. DellEMC#show fefd FEFD is globally 'ON', interval is 3 seconds, mode is 'Normal'.
PAGE 511
Debugging FEFD To debug FEFD, use the first command. To provide output for each packet transmission over the FEFD enabled connection, use the second command. ● Display output whenever events occur that initiate or disrupt an FEFD enabled connection. EXEC Privilege mode debug fefd events ● Provide output for each packet transmission over the FEFD enabled connection.
PAGE 512
28 Link Layer Discovery Protocol (LLDP) This chapter describes how to configure and use the link layer discovery protocol (LLDP). Topics: • • • • • • • • • • • • • • • • • 802.
PAGE 513
Figure 76. Type, Length, Value (TLV) Segment TLVs are encapsulated in a frame called an LLDP data unit (LLDPDU) (shown in the following table), which is transmitted from one LLDP-enabled device to its LLDP-enabled neighbors. LLDP is a one-way protocol. LLDP-enabled devices (LLDP agents) can transmit and/or receive advertisements, but they cannot solicit and do not respond to advertisements. There are five types of TLVs. All types are mandatory in the construction of an LLDPDU except Optional TLVs.
PAGE 514
Optional TLVs The Dell EMC Networking OS supports these optional TLVs: management TLVs, IEEE 802.1 and 802.3 organizationally specific TLVs, and TIA-1057 organizationally specific TLVs. Management TLVs A management TLV is an optional TLVs sub-type. This kind of TLV contains essential management information about the sender. Organizationally Specific TLVs A professional organization or a vendor can define organizationally specific TLVs.
PAGE 515
Table 53. Optional TLV Types (continued) Type TLV Description port belongs (and the untagged VLAN to which a port belongs if the port is in Hybrid mode). 127 Protocol Identity Indicates the protocols that the port can process. Dell EMC Networking OS does not currently support this TLV. 127 MAC/PHY Configuration/Status Indicates the capability and current setting of the duplex status and bit rate, and whether the current settings are the result of auto-negotiation.
PAGE 516
TIA Organizationally Specific TLVs The Dell EMC Networking system is an LLDP-MED Network Connectivity Device (Device Type 4). Network connectivity devices are responsible for: ● transmitting an LLDP-MED capability TLV to endpoint devices ● storing the information that endpoint devices advertise The following table describes the five types of TIA-1057 Organizationally Specific TLVs. Table 54.
PAGE 517
Table 54. TIA-1057 (LLDP-MED) Organizationally Specific TLVs (continued) Type SubType TLV Description 127 11 Inventory — Asset ID Indicates a user specified device number to manage inventory. 127 12–255 Reserved — LLDP-MED Capabilities TLV The LLDP-MED capabilities TLV communicates the types of TLVs that the endpoint device and the network connectivity device support. LLDP-MED network connectivity devices must transmit the Network Policies TLV.
PAGE 518
LLDP-MED Network Policies TLV A network policy in the context of LLDP-MED is a device’s VLAN configuration and associated Layer 2 and Layer 3 configurations. LLDP-MED network policies TLV include: ● ● ● ● VLAN ID VLAN tagged or untagged status Layer 2 priority DSCP value An integer represents the application type (the Type integer shown in the following table), which indicates a device function for which a unique network policy is defined.
PAGE 519
Extended Power via MDI TLV The extended power via MDI TLV enables advanced PoE management between LLDP-MED endpoints and network connectivity devices. Advertise the extended power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. ● Power Type — there are two possible power types: power source entity (PSE) or power device (PD). The Dell EMC Networking system is a PSE, which corresponds to a value of 0, based on the TIA-1057 specification.
PAGE 520
● 802.1X controlled ports do not allow LLDPDUs until the connected device is authenticated. CONFIGURATION versus INTERFACE Configurations All LLDP configuration commands are available in PROTOCOL LLDP mode, which is a sub-mode of the CONFIGURATION mode and INTERFACE mode. ● Configurations made at the CONFIGURATION level are global; that is, they affect all interfaces on the system.
PAGE 521
To undo an LLDP configuration, precede the relevant command with the keyword no. Enabling LLDP on Management Ports LLDP on management ports is enabled by default. To enable LLDP on management ports, use the following command. 1. Enter Protocol LLDP mode. CONFIGURATION mode protocol lldp 2. Enter LLDP management-interface mode. LLDP-MANAGEMENT-INTERFACE mode management-interface 3. Enable LLDP.
PAGE 522
● For TIA-1057 TLVs: ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ guest-voice guest-voice-signaling location-identification power-via-mdi softphone-voice streaming-video video-conferencing video-signaling voice voice-signaling In the following example, LLDP is enabled globally. R1 and R2 are transmitting periodic LLDPDUs that contain management, 802.1, and 802.3 TLVs. Figure 82.
PAGE 523
The system processes each LLDP frame to retrieve the OUI, subtype, and data length, and stores the retrieved data of organizational specific unrecognized LLDP TLVs in a list. The stored list of organizational TLVs is removed when the neighbor is lost or neighbor ages out. The software assigns a temporary identification index for each unrecognized organizational specific LLDP TLVs upon receiving more than one TLV with the same OUI and subtype, but with different organizationally defined information strings.
PAGE 524
Viewing Information Advertised by Adjacent LLDP Neighbors To view brief information about adjacent devices or to view all the information that neighbors are advertising, use the following commands. ● Display brief information about adjacent devices. show lldp neighbors ● Display all of the information that neighbors are advertising.
PAGE 525
1000BASE-T half duplex mode Operational MAU type: unknown UnknownTLVList: OrgUnknownTLVList: ((f8-b1-56), 24, 1) ((f8-b1-56), 23, 1) ((f8-b1-56), 22, 1) ((f8-b1-56), 21, 7) ((00-80-c2), 7, 5) --------------------------------------------------------------------------Following note is applicable only in platforms that support 25G interfaces: NOTE: Since different port types are shown in two letters, the 25G interface is represented as tf (Twentyfive) in show lldp neighbors output.
PAGE 526
Total Neighbor information Age outs: 0 Total Multiple Neighbors Detected: 0 Total Frames Discarded: 0 Total In Error Frames: 0 Total Unrecognized TLVs: 1056 Total TLVs Discarded: 0 Next packet will be sent after 16 seconds The neighbors are given below: ----------------------------------------------------------------------Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet
PAGE 527
R1(conf-lldp)#hello 25 R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description hello 25 no disable R1(conf-lldp)#no hello R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)# Configuring LLDP Notification I
PAGE 528
rx Rx only tx Tx only R1(conf-lldp)#mode tx R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description mode tx no disable R1(conf-lldp)#no mode R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)# Configuring
PAGE 529
Debugging LLDP You can view the TLVs that your system is sending and receiving. To view the TLVs, use the following commands. ● View a readable version of the TLVs. debug lldp brief ● View a readable version of the TLVs plus a hexadecimal version of the entire LLDPDU, including unrecognized TLVs. debug lldp detail To stop viewing the LLDP TLVs sent and received by the system, use the no debug lldp command. Figure 83.
PAGE 530
Relevant Management Objects Dell EMC Networking OS supports all IEEE 802.1AB MIB objects. The following tables list the objects associated with: ● ● ● ● received and transmitted TLVs the LLDP configuration on the local agent IEEE 802.1AB Organizationally Specific TLVs received and transmitted LLDP-MED TLVs Table 58.
PAGE 531
Table 59.
PAGE 532
Table 60. LLDP 802.
PAGE 533
Table 61.
PAGE 534
29 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems (OSs). NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
PAGE 535
Limitations of the NLB Feature The following limitations apply to switches on which you configure NLB: ● The NLB Unicast mode uses switch flooding to transmit all packets to all the servers that are part of the VLAN. When a large volume of traffic is processed, the clustering performance might be impacted in a small way. This limitation is applicable to switches that perform unicast flooding in the software. ● The ip vlan-flooding command applies globally across the system and for all VLANs.
PAGE 536
There might be some ARP table entries that are resolved through ARP packets, which had the Ethernet MAC SA different from the MAC information inside the ARP packet. This unicast data traffic flooding occurs only for those packets that use these ARP entries. Enabling a Switch for Multicast NLB To enable a switch for Multicast NLB mode, perform the following steps: 1.
PAGE 537
30 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) is supported on Dell EMC Networking OS. Protocol Overview MSDP is a Layer 3 protocol that connects IPv4 protocol-independent multicast-sparse mode (PIM-SM) domains. A domain in the context of MSDP is a contiguous set of routers operating PIM within a common boundary defined by an exterior gateway protocol, such as border gateway protocol (BGP).
PAGE 538
Figure 85.
PAGE 539
Implementation Information The Dell EMC Networking OS implementation of MSDP is in accordance with RFC 3618 and Anycast RP is in accordance with RFC 3446. Configure Multicast Source Discovery Protocol Configuring MSDP is a four-step process. 1. Enable an exterior gateway protocol (EGP) with at least two routing domains. Refer to the following figures. The MSDP Sample Configurations show the OSPF-BGP configuration used in this chapter for MSDP.
PAGE 540
Figure 86.
PAGE 541
Figure 87.
PAGE 542
Figure 88.
PAGE 543
Figure 89. Configuring MSDP Enable MSDP Enable MSDP by peering RPs in different administrative domains. 1. Enable MSDP. CONFIGURATION mode ip multicast-msdp 2. Peer PIM systems in different administrative domains. CONFIGURATION mode ip msdp peer connect-source R3(conf)#ip multicast-msdp R3(conf)#ip msdp peer 192.168.0.
PAGE 544
Multicast sources in remote domains are stored on the RP in the source-active cache (SA cache). The system does not create entries in the multicast routing table until there is a local receiver for the corresponding multicast group. R3#show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.
PAGE 545
Clearing the Source-Active Cache To clear the source-active cache, use the following command. ● Clear the SA cache of all, local, or rejected entries, or entries for a specific group. CONFIGURATION mode clear ip msdp sa-cache [group-address | local | rejected-sa] Enabling the Rejected Source-Active Cache To cache rejected sources, use the following command. Active sources can be rejected because the RPF check failed, the SA limit is reached, the peer RP is unreachable, or the SA message has a format error.
PAGE 546
Figure 90.
PAGE 547
Figure 91.
PAGE 548
Figure 92. MSDP Default Peer, Scenario 4 Specifying Source-Active Messages To specify messages, use the following command. ● Specify the forwarding-peer and originating-RP from which all active sources are accepted without regard for the RPF check. CONFIGURATION mode ip msdp default-peer ip-address list If you do not specify an access list, the peer accepts all sources that peer advertises. All sources from RPs that the ACL denies are subject to the normal RPF check. DellEMC(conf)#ip msdp peer 10.0.50.
PAGE 549
DellEMC#ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 3 rejected SAs received, cache-size 32766 UpTime GroupAddr SourceAddr RPAddr 00:33:18 229.0.50.64 24.0.50.64 200.0.1.50 00:33:18 229.0.50.65 24.0.50.65 200.0.1.50 00:33:18 229.0.50.66 24.0.50.66 200.0.1.50 LearnedFrom 10.0.50.2 10.0.50.2 10.0.50.2 Reason Rpf-Fail Rpf-Fail Rpf-Fail Limiting the Source-Active Messages from a Peer To limit the source-active messages from a peer, use the following commands. 1.
PAGE 550
Preventing MSDP from Caching a Remote Source To prevent MSDP from caching a remote source, use the following commands. 1. OPTIONAL: Cache sources that the SA filter denies in the rejected SA cache. CONFIGURATION mode ip msdp cache-rejected-sa 2. Prevent the system from caching remote sources learned from a specific peer based on source and group. CONFIGURATION mode ip msdp sa-filter list out peer list ext-acl As shown in the following example, R1 is advertising source 10.11.4.2.
PAGE 551
MSDP Source-Active Cache - 1 entries GroupAddr SourceAddr RPAddr LearnedFrom 239.0.0.1 10.11.4.2 192.168.0.1 local R3(conf)#do show ip msdp sa-cache MSDP Source-Active Cache - 1 entries GroupAddr SourceAddr RPAddr LearnedFrom 239.0.0.1 10.11.4.2 192.168.0.1 192.168.0.1 Expire 70 UpTime 00:27:20 Expire 1 UpTime 00:10:29 [Router 3] R3(conf)#do show ip msdp sa-cache R3(conf)# To display the configured SA filters for a peer, use the show ip msdp peer command from EXEC Privilege mode.
PAGE 552
CONFIGURATION mode clear ip msdp peer peer-address R3(conf)#do show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.3(639) Connect Source: Lo 0 State: Established Up/Down Time: 00:04:26 Timers: KeepAlive 30 sec, Hold time 75 sec SourceActive packet count (in/out): 5/0 SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: myremotefilter Output (S,G) filter: none R3(conf)#do clear ip msdp peer 192.168.0.1 R3(conf)#do show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 0.0.0.
PAGE 553
Anycast RP relieves these limitations by allowing multiple RPs per group, which can be distributed in a topologically significant manner according to the locations of the sources and receivers. 1. All the RPs serving a given group are configured with an identical anycast address. 2. Sources then register with the topologically closest RP. 3. RPs use MSDP to peer with each other using a unique address. Figure 93.
PAGE 554
4. Peer each RP with every other RP using MSDP, specifying the unique Loopback address as the connect-source. CONFIGURATION mode ip msdp peer 5. Advertise the network of each of the unique Loopback addresses throughout the network. ROUTER OSPF mode network Reducing Source-Active Message Flooding RPs flood source-active messages to all of their peers away from the RP.
PAGE 555
! ip ip ip ip ip multicast-msdp msdp peer 192.168.0.3 connect-source Loopback 1 msdp peer 192.168.0.22 connect-source Loopback 1 msdp mesh-group AS100 192.168.0.22 msdp originator-id Loopback 1! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 The following example shows an R2 configuration for MSDP with Anycast RP. ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.
PAGE 556
ip address 10.11.6.34/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.3/32 no shutdown ! router ospf 1 network 10.11.6.0/24 area 0 network 192.168.0.3/32 area 0 redistribute static redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.22 remote-as 100 neighbor 192.168.0.22 ebgp-multihop 255 neighbor 192.168.0.22 update-source Loopback 0 neighbor 192.168.0.22 no shutdown ! ip multicast-msdp ip msdp peer 192.168.0.
PAGE 557
! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 MSDP Sample Configuration: R2 Running-Config ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.21/24 no shutdown ! interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.0.23/24 no shutdown ! interface Loopback 0 ip address 192.168.0.2/32 no shutdown ! router ospf 1 network 10.11.1.
PAGE 558
redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.2 remote-as 100 neighbor 192.168.0.2 ebgp-multihop 255 neighbor 192.168.0.2 update-source Loopback 0 neighbor 192.168.0.2 no shutdown ! ip multicast-msdp ip msdp peer 192.168.0.1 connect-source Loopback 0 ! ip route 192.168.0.2/32 10.11.0.23 MSDP Sample Configuration: R4 Running-Config ip multicast-routing ! interface TenGigabitEthernet 4/1 ip pim sparse-mode ip address 10.11.5.
PAGE 559
31 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP) — specified in IEEE 802.1Q-2003 — is a rapid spanning tree protocol (RSTP)-based spanning tree variation that improves per-VLAN spanning tree plus (PVST+). MSTP allows multiple spanning tree instances and allows you to map many VLANs to one spanning tree instance to reduce the total number of required instances. Protocol Overview MSTP — specified in IEEE 802.
PAGE 560
• • • • • • • Modifying Global Parameters Modifying the Interface Parameters Setting STP path cost as constant Configuring an EdgePort Flush MAC Addresses after a Topology Change MSTP Sample Configurations Debugging and Verifying MSTP Configurations Spanning Tree Variations The Dell EMC Networking OS supports four variations of spanning tree, as shown in the following table. Table 62. Spanning Tree Variations Dell EMC Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .
PAGE 561
● Enabling SNMP Traps for Root Elections and Topology Changes ● Configuring Spanning Trees as Hitless Enable Multiple Spanning Tree Globally MSTP is not enabled by default. To enable MSTP globally, use the following commands. When you enable MSTP, all physical, VLAN, and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the MSTI 0. ● Within an MSTI, only one path from any bridge to any other bridge is enabled.
PAGE 562
no disable MSTI 1 VLAN 100 MSTI 2 VLAN 200-300 All bridges in the MSTP region must have the same VLAN-to-instance mapping. To view which instance a VLAN is mapped to, use the show spanning-tree mst vlan command from EXEC Privilege mode.
PAGE 563
To view the bridge priority, use the show config command from PROTOCOL MSTP mode. R3(conf-mstp)#msti 2 bridge-priority 0 1d2h51m: %RPM0-P:RP2 %SPANMGR-5-STP_ROOT_CHANGE: MSTP root changed for instance 2. My Bridge ID: 0:0001.e809.c24a Old Root: 32768:0001.e806.953e New Root: 0:0001.e809.c24a R3(conf-mstp)#show config ! protocol spanning-tree mstp no disable MSTI 1 VLAN 100 MSTI 2 VLAN 200,300 MSTI 2 bridge-priority 0 Interoperate with Non-Dell Bridges Dell EMC Networking OS supports only one MSTP region.
PAGE 564
● Hello-time — the time interval in which the bridge sends MSTP bridge protocol data units (BPDUs). ● Max-age — the length of time the bridge maintains configuration information before it refreshes that information by recomputing the MST topology. ● Max-hops — the maximum number of hops a BPDU can travel before a receiving switch discards it. NOTE: Dell EMC Networking recommends that only experienced network administrators change MSTP parameters.
PAGE 565
The following lists the default values for port cost by interface. Table 63.
PAGE 566
Configuring an EdgePort The EdgePort feature enables interfaces to begin forwarding traffic approximately 30 seconds sooner. In this mode, an interface forwards frames by default until it receives a BPDU that indicates that it should behave otherwise; it does not go through the Learning and Listening states. The bpduguard shutdown-on-violation option causes the interface hardware to be shut down when it receives a BPDU.
PAGE 567
MSTP Sample Configurations The running-configurations support the topology shown in the following illustration. The configurations are from Dell EMC Networking OS systems. Figure 95. MSTP with Three VLANs Mapped to Two Spanning Tree Instances Router 1 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3.
PAGE 568
no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown Router 2 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3. Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
PAGE 569
(Step 2) interface TenGigabitEthernet 3/11 no ip address switchport no shutdown ! interface TenGigabitEthernet 3/21 no ip address switchport no shutdown ! (Step 3) interface Vlan 100 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown SFTOS Example Running-Configuration This example uses the following steps: 1.
PAGE 570
tagged 1/0/31 tagged 1/0/32 exit Debugging and Verifying MSTP Configurations To debut and verify MSTP configuration, use the following commands. ● Display BPDUs. EXEC Privilege mode debug spanning-tree mstp bpdu ● Display MSTP-triggered topology change messages. debug spanning-tree mstp events To ensure all the necessary parameters match (region name, region version, and VLAN to instance mapping), examine your individual routers.
PAGE 571
Brg/Port Prio: 32768/128, Rem Hops: 20 4w0d4h : MSTP: Received BPDU on Te 2/21 : ProtId: 0, Ver: 3, Bpdu Type: MSTP, Flags 0x78 (Indicates MSTP routers are in the [single] region.) CIST Root Bridge Id: 32768:0001.e806.953e, Ext Path Cost: 0 Regional Bridge Id: 32768:0001.e806.953e, CIST Port Id: 128:470 Msg Age: 0, Max Age: 20, Hello: 2, Fwd Delay: 15, Ver1 Len: 0, Ver3 Len: 96 Name: Tahiti, Rev: 123 (MSTP region name and revision), Int Root Path Cost: 0 Rem Hops: 19, Bridge Id: 32768:0001.e8d5.
PAGE 572
32 Multicast Features NOTE: Multicast routing is supported on secondary IP addresses; it is not supported on IPv6. NOTE: Multicast routing is supported across default and non-default virtual routing and forwarding (VRFs).
PAGE 573
Protocol Ethernet Address RIP 01:00:5e:00:00:09 NTP 01:00:5e:00:01:01 VRRP 01:00:5e:00:00:12 PIM-SM 01:00:5e:00:00:0d ● ● ● ● The Dell EMC Networking OS implementation of MTRACE is in accordance with IETF draft draft-fenner-traceroute-ipm. Multicast is not supported on secondary IP addresses. If you enable multicast routing, egress Layer 3 ACL is not applied to multicast data traffic. Multicast traffic can be forwarded to a maximum of 15 VLANs with the same outgoing interface.
PAGE 574
● Limit the total number of multicast routes on the system. CONFIGURATION mode ip multicast-limit The range is from 1 to 16000. The default is 4000. NOTE: The IN-L3-McastFib CAM partition stores multicast routes and is a separate hardware limit that exists per portpipe. Any software-configured limit may supersede this hardware space limitation. The opposite is also true, the CAM partition might not be exhausted at the time the system-wide route limit is reached using the ip multicast-limit command.
PAGE 575
Figure 96. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 64. Preventing a Host from Joining a Group — Description Location Description 1/21 ● ● ● ● Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 ● ● ● ● Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
PAGE 576
Table 64. Preventing a Host from Joining a Group — Description (continued) Location Description 2/11 ● ● ● ● Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 ● ● ● ● Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 ● ● ● ● Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 ● ● ● ● Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
PAGE 577
Initially, a single PIM-SM tree called a shared tree to distribute traffic. It is called shared because all traffic for the group, regardless of the source, or the location of the source, must pass through the RP. The shared tree is unidirectional; that is, all multicast traffic flows only from the RP to the receivers. Once a receiver receives traffic from the RP, PM-SM switches to SPT to forward multicast traffic, which connects the receiver directly to the source.
PAGE 578
Figure 97. Preventing a Source from Transmitting to a Group The following table lists the location and description shown in the previous illustration. Table 66. Preventing a Source from Transmitting to a Group — Description Location Description 1/21 ● ● ● ● Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 ● ● ● ● Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
PAGE 579
Table 66. Preventing a Source from Transmitting to a Group — Description (continued) Location Description 2/11 ● ● ● ● Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 ● ● ● ● Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 ● ● ● ● Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 ● ● ● ● Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
PAGE 580
Understanding Multicast Traceroute (mtrace) Multicast Traceroute (mtrace) is a multicast diagnostic facility used for tracing multicast paths. Mtrace enables you to trace the path that a multicast packet takes from its source to the destination. When you initiate mtrace from a source to a destination, an mtrace Query packet with IGMP type 0x1F is sent to the last-hop multicast router for the given destination. The mtrace query packet is forwarded hop-by-hop untill it reaches the last-hop router.
PAGE 581
● MTRACE Transit — when a Dell EMC Networking system is an intermediate router between the source and destination in an MTRACE query, Dell EMC Networking OS computes the RPF neighbor for the source, fills in the request, and forwards the request to the RPF neighbor. When a Dell EMC Networking system is the last hop to the destination, Dell EMC Networking OS sends a response to the query. To print the network path, use the following command.
PAGE 582
Table 67. mtrace Command Output — Explained (continued) Command Output Description From source (?) to destination (?) In case the provided source or destination IP can be resolved to a hostname the corresponding name will be displayed. In cases where the IP cannot be resolved, it is displayed as (?) 0 1.1.1.1 --> Destination The first row in the table corresponds to the destination provided by the user. -1 1.1.1.1 PIM Reached RP/Core 103.103.103.
PAGE 583
Table 68. Supported Error Codes (continued) Error Code Error Name Description 0x81 NO_SPACE There is not enough room to insert another response data block in the packet. mtrace Scenarios This section describes various scenarios that may result when an mtrace command is issued. The following table describes various scenarios when the mtrace command is issued: Table 69.
PAGE 584
Table 69. Mtrace Scenarios (continued) Scenario You invoke a weak mtrace request by specifying only the source without specifying the mulicast tree or multicast group information for the source. Mtrace traces a path towards the source by using the RPF neighbor at each node. Output R1>mtrace 103.103.103.3 Type Ctrl-C to abort. Querying reverse path for source 103.103.103.
PAGE 585
Table 69. Mtrace Scenarios (continued) Scenario When you issue the mtrace command with the source and multicast group information, if a multicast route is not present on a particular node, then the NO ROUTE error code is displayed on the node. In this scenario, the Source Network/Mask column for that particular node displays the the value as default.
PAGE 586
Table 69. Mtrace Scenarios (continued) Scenario Output ----------------------------------------------------------------- If the destination provided in the command is not a valid receiver for the multicast group, the last hop router for the destination provides the WRONG LAST HOP error code. If the last-hop router contains a path to the source, the path is traced irrespective of the incorrect destination.
PAGE 587
Table 69. Mtrace Scenarios (continued) Scenario Output 0 1.1.1.1 --> Destination -1 * * * * ----------------------------------------------------------------Timed out receiving responses Perhaps no local router has a route for source, the receiver is not a member of the multicast group or the multicast ttl is too low. While traversing the path from source to destination, if the mtrace packet exhausts the maximum buffer size of the packet, then NO SPACE error is displayed in the output.
PAGE 588
Table 69. Mtrace Scenarios (continued) Scenario Output Querying reverse path for source 6.6.6.6 to destination 4.4.4.5 via RPF From source (?) to destination (?) ---------------------------------------------------------------|Hop| OIF IP |Proto| Forwarding Code |Source Network/Mask| ---------------------------------------------------------------0 4.4.4.5 --> Destination -1 4.4.4.4 PIM 6.6.6.0/24 -2 20.20.20.2 PIM 6.6.6.0/24 -3 10.10.10.1 PIM RPF Interface 6.6.6.
PAGE 589
33 Object Tracking IPv4 or IPv6 object tracking is available on Dell EMC Networking OS. Object tracking allows the Dell EMC Networking OS client processes, such as virtual router redundancy protocol (VRRP), to monitor tracked objects (for example, interface or link status) and take appropriate action when the state of an object changes. NOTE: In Dell EMC Networking OS release version 8.4.1.0, object tracking is supported only on VRRP.
PAGE 590
Figure 98. Object Tracking Example When you configure a tracked object, such as an IPv4/IPv6 a route or interface, you specify an object number to identify the object. Optionally, you can also specify: ● UP and DOWN thresholds used to report changes in a route metric. ● A time delay before changes in a tracked object’s state are reported to a client. Track Layer 2 Interfaces You can create an object to track the line-protocol state of a Layer 2 interface.
PAGE 591
Track IPv4 and IPv6 Routes You can create an object that tracks an IPv4 or IPv6 route entry in the routing table. Specify a tracked route by its IPv4 or IPv6 address and prefix-length. Optionally specify a tracked route by a virtual routing and forwarding (VRF) instance name if the route to be tracked is part of a VRF. The next-hop address is not part of the definition of the tracked object.
PAGE 592
Set Tracking Delays You can configure an optional UP and/or DOWN timer for each tracked object to set the time delay before a change in the state of a tracked object is communicated to clients. The configured time delay starts when the state changes from UP to DOWN or the opposite way. If the state of an object changes back to its former UP/DOWN state before the timer expires, the timer is cancelled and the client is not notified.
PAGE 593
OBJECT TRACKING mode delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status.
PAGE 594
The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status.
PAGE 595
priority over a higher value. The resulting scaled value is compared against the configured threshold values to determine the state of a tracked route as follows: ○ If the scaled metric for a route entry is less than or equal to the UP threshold, the state of a route is UP. ○ If the scaled metric for a route is greater than or equal to the DOWN threshold or the route is not entered in the routing table, the state of a route is DOWN. The UP and DOWN thresholds are user-configurable for each tracked route.
PAGE 596
2 changes, last change 00:02:49 Tracked by: DellEMC#configure DellEMC(conf)#track 4 ip route 3.1.1.
PAGE 597
2. Configure object tracking on the metric of an IPv4 or IPv6 route. CONFIGURATION mode track object-id {ip route ip-address/prefix-len | ipv6 route ipv6-address/prefix-len} metric threshold [vrf vrf-name] Valid object IDs are from 1 to 500. Enter an IPv4 address in dotted decimal format. Valid IPv4 prefix lengths are from /0 to /32. Enter an IPv6 address in X:X:X:X::X format. Valid IPv6 prefix lengths are from /0 to /128. (Optional) E-Series only: For an IPv4 route, you can enter a VRF name. 3.
PAGE 598
● Display the configuration and status of currently tracked Layer 2 or Layer 3 interfaces, IPv4 or IPv6 routes, and a VRF instance. show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] ● Use the show running-config track command to display the tracking configuration of a specified object or all objects that are currently configured on the router.
PAGE 599
Example of Viewing Object Tracking Configuration DellEMC#show running-config track track 1 ip route 23.0.0.0/8 reachability track 2 ipv6 route 2040::/64 metric threshold delay down 3 delay up 5 threshold metric up 200 track 3 ipv6 route 2050::/64 reachability track 4 interface TenGigabitEthernet 1/4 ip routing track 5 ip route 192.168.0.
PAGE 600
34 Open Shortest Path First (OSPFv2 and OSPFv3) Open shortest path first (OSPFv2 for IPv4) and OSPF version 3 (OSPF for IPv6) are supported on Dell EMC Networking OS. This chapter provides a general description of OSPFv2 (OSPF for IPv4) and OSPFv3 (OSPF for IPv6) as supported in the Dell EMC Networking Operating System (OS). NOTE: The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) are the same between OSPFv2 and OSPFv3.
PAGE 601
Figure 99. Autonomous System Areas Area Types The backbone of the network is Area 0. It is also called Area 0.0.0.0 and is the core of any AS. All other areas must connect to Area 0. An OSPF backbone is responsible for distributing routing information between areas. It consists of all area border routers, networks not wholly contained in any area, and their attached routers. NOTE: If you configure two non-backbone areas, then you must enable the B bit in OSPF.
PAGE 602
Networks and Neighbors As a link-state protocol, OSPF sends routing information to other OSPF routers concerning the state of the links between them. The state (up or down) of those links is important. Routers that share a link become neighbors on that segment. OSPF uses the Hello protocol as a neighbor discovery and keep alive mechanism. After two routers are neighbors, they may proceed to exchange and synchronize their databases, which creates an adjacency.
PAGE 603
Backbone Router (BR) A backbone router (BR) is part of the OSPF Backbone, Area 0. This includes all ABRs. It can also include any routers that connect only to the backbone and another ABR, but are only part of Area 0, such as Router I in the previous example. Area Border Router (ABR) Within an AS, an area border router (ABR) connects one or more areas to the backbone. The ABR keeps a copy of the link-state database for every area it connects to, so it may keep multiple copies of the link state database.
PAGE 604
● Type 3: Summary LSA (OSPFv2), Inter-Area-Prefix LSA (OSPFv3) — An ABR takes information it has learned on one of its attached areas and can summarize it before sending it out on other areas it is connected to. The link-state ID of the Type 3 LSA is the destination network number. ● Type 4: AS Border Router Summary LSA (OSPFv2), Inter-Area-Router LSA (OSPFv3) — In some cases, Type 5 External LSAs are flooded to areas where the detailed next-hop information may not be available.
PAGE 605
Figure 101. Priority and Cost Examples OSPF with Dell EMC Networking OS The Dell EMC Networking OS supports up to 128,000 OSPF routes for OSPFv2. Dell EMC Networking OS version 9.4(0.0) and later support only one OSPFv2 process per VRF. Dell EMC Networking OS version 9.7(0.0) and later support OSPFv3 in VRF. Also, on OSPFv3, Dell EMC Networking OS supports only one OSPFv3 process per VRF. OSPFv2 and OSPFv3 can co-exist but you must configure them individually.
PAGE 606
OSPF graceful restart understands that in a modern router, the control plane and data plane functionality are separate, restarting the control plane functionality (such as the failover of the active RPM to the backup in a redundant configuration), does not necessarily have to interrupt the forwarding of data packets.
PAGE 607
Multi-Process OSPFv2 with VRF Multi-process OSPF with VRF is supported on the Dell EMC Networking OS. Only one OSPFv2 process per VRF is supported. Multi-process OSPF allows multiple OSPFv2 processes on a single router. Multiple OSPFv2 processes allow for isolating routing domains, supporting multiple route policies and priorities in different domains, and creating smaller domains for easier management. The system supports up to 16 OSPFv2 processes.
PAGE 608
LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.2.0 Adv:6.1.0.0 Netmask:255.255.255.0 fwd:0.0.0.0 E2, tos:0 metric:0 RFC 2328 is supported by default on Dell EMC Networking OS and it is indicated in the show ip ospf command output. DellEMC#show ip ospf Routing Process ospf 1 with ID 2.2.2.
PAGE 609
Configuration Information The interfaces must be in Layer 3 mode (assigned an IP address) and enabled so that they can send and receive traffic. The OSPF process must know about these interfaces. To make the OSPF process aware of these interfaces, they must be assigned to OSPF areas. You must configure OSPF GLOBALLY on the system in CONFIGURATION mode. NOTE: Loop back routes are not installed in the Route Table Manager (RTM) as non-active routes.
PAGE 610
Enabling OSPFv2 To enable Layer 3 routing, assign an IP address to an interface (physical or Loopback). By default, OSPF, similar to all routing protocols, is disabled. You must configure at least one interface for Layer 3 before enabling OSPFv2 globally. If implementing multi-process OSPF, create an equal number of Layer 3 enabled interfaces and OSPF process IDs. For example, if you create four OSPFv2 process IDs, you must have four interfaces with Layer 3 enabled. 1. Assign an IP address to an interface.
PAGE 611
Supports only single TOS (TOS0) routes SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Number of area in this router is 0, normal 0 stub 0 nssa 0 DellEMC# Assigning an OSPFv2 Area After you enable OSPFv2, assign the interface to an OSPF area. Set up OSPF areas and enable OSPFv2 on an interface with the network command. You must have at least one AS area: Area 0. This is the backbone area. If your OSPF network contains more than one area, configure a backbone area (Area ID 0.0.0.0).
PAGE 612
To view currently active interfaces and the areas assigned to them, use the show ip ospf interface command. Example of Viewing Active Interfaces and Assigned Areas DellEMC>show ip ospf 1 interface TenGigabitEthernet 1/17 is up, line protocol is up Internet Address 10.2.2.1/24, Area 0.0.0.0 Process ID 1, Router ID 11.1.2.1, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 11.1.2.1, Interface address 10.2.2.1 Backup Designated Router (ID) 0.0.0.
PAGE 613
configure 3. Enter ROUTER OSPF mode. CONFIGURATION mode router ospf process-id [vrf] Process ID is the ID assigned when configuring OSPFv2 globally. 4. Configure the area as a stub area. CONFIG-ROUTER-OSPF-id mode area area-id stub [no-summary] Use the keywords no-summary to prevent transmission into the area of summary ASBR LSAs. Area ID is the number or IP address assigned when creating the area.
PAGE 614
Backup Designated Router (ID) 0.0.0.0, Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 13:39:46 Neighbor Count is 0, Adjacent neighbor count is 0 TenGigabitEthernet 2/1 is up, line protocol is down Internet Address 10.1.3.100/24, Area 2.2.2.2 Process ID 34, Router ID 10.1.2.100, Network Type BROADCAST, Cost: 10 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 10.1.2.100, Interface address 10.1.3.
PAGE 615
Min LSA origination 5 secs, Min LSA arrival 1 secs Number of area in this router is 0, normal 0 stub 0 nssa 0 DellEMC# Changing OSPFv2 Parameters on Interfaces In Dell EMC Networking OS, you can modify the OSPF settings on the interfaces. Some interface parameter values must be consistent across all interfaces to avoid routing errors. For example, set the same time interval for the hello packets on all routers in the OSPF network to prevent misconfiguration of OSPF neighbors.
PAGE 616
ip ospf transmit-delay seconds ○ seconds: the range is from 1 to 65535 (the default is 1 second). The transmit delay must be the same on all routers in the OSPF network. To view interface configurations, use the show config command in CONFIGURATION INTERFACE mode. To view interface status in the OSPF process, use the show ip ospf interface command in EXEC mode. The bold lines in the example show the change on the interface. The change is reflected in the OSPF configuration.
PAGE 617
● mode — the situation or situations that trigger a graceful restart. ● role — the role or roles the configured router can perform. NOTE: By default, OSPFv2 graceful restart is disabled. To enable and configure OSPFv2 graceful restart, use the following commands. 1. Enable OSPFv2 graceful-restart globally and set the grace period. CONFIG-ROUTEROSPF- id mode graceful-restart grace-period seconds The seconds range is from 40 and 3000.
PAGE 618
Creating Filter Routes To filter routes, use prefix lists. OSPF applies prefix lists to incoming or outgoing routes. Incoming routes must meet the conditions of the prefix lists. If they do not, OSPF does not add the route to the routing table. Configure the prefix list in CONFIGURATION PREFIX LIST mode prior to assigning it to the OSPF process. ● Create a prefix list and assign it a unique name. CONFIGURATION mode ip prefix-list prefix-name You are in PREFIX LIST mode.
PAGE 619
router ospf 34 network 10.1.2.32 0.0.0.255 area 2.2.2.2 network 10.1.3.24 0.0.0.255 area 3.3.3.3 distribute-list dilling in DellEMC(conf-router_ospf)# Troubleshooting OSPFv2 Use the information in this section to troubleshoot OSPFv2 operation on the switch. Be sure to check the following, as these questions represent typical issues that interrupt an OSPFv2 process. NOTE: The following tasks are not a comprehensive; they provide some examples of typical troubleshooting checks.
PAGE 620
○ database-timers rate-limit: view the LSAs currently in the queue. DellEMC#show run ospf ! router ospf 4 router-id 4.4.4.4 network 4.4.4.0/28 area 1 ! ipv6 router ospf 999 default-information originate always router-id 10.10.10.10 DellEMC# Sample Configurations for OSPFv2 The following configurations are examples for enabling OSPFv2. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations.
PAGE 621
ip address 192.168.10.100/24 no shutdown OSPF Area 0 — Te 3/1 and 3/2 router ospf 33333 network 192.168.20.0/24 area 0 network 10.1.1.0/24 area 0 network 10.2.13.0/24 area 0 ! interface Loopback 30 ip address 192.168.20.100/24 no shutdown ! interface TenGigabitEthernet 3/1 ip address 10.1.1.2/24 no shutdown ! interface TenGigabitEthernet 3/2 ip address 10.2.13.3/24 no shutdown OSPF Area 0 — Te 2/1 and 2/2 router ospf 22222 network 192.168.30.0/24 area 0 network 10.1.11.0/24 area 0 network 10.2.13.
PAGE 622
3. No-summary – To act as totally stubby area — NSSA area can be converted intoa totally stubby area to reduce the number of Type-3 LSAs. Once it is configured, NSSA ABR will inject Type-3 LSAs into the NSSA area for default routes. The remaining Type-3 LSAs are not allowed inside this area. Configuration Task List for OSPFv3 (OSPF for IPv6) This section describes the configuration tasks for Open Shortest Path First version 3 (OSPF for IPv6) on the switch.
PAGE 623
INTERFACE mode ipv6 ospf interface-cost ○ interface-cost:The range is from 1 to 65535. Default cost is based on the bandwidth. ● Specify how the OSPF interface cost is calculated based on the reference bandwidth method. The cost of an interface is calculated as Reference Bandwidth/Interface speed. ROUTER OSPFv3 auto-cost [reference-bandwidth ref-bw] To return to the default bandwidth or to assign cost based on the interface type, use the no auto-cost [referencebandwidth ref-bw] command.
PAGE 624
router-id {number} ○ number: the IPv4 address. The format is A.B.C.D. NOTE: Enter the router-id for an OSPFv3 router as an IPv4 IP address. ● Disable OSPF. CONFIGURATION mode no ipv6 router ospf process-id ● Reset the OSPFv3 process. EXEC Privilege mode clear ipv6 ospf process Assigning OSPFv3 Process ID and Router ID to a VRF To assign, disable, or reset OSPFv3 on a non-default VRF, use the following commands. ● Enable the OSPFv3 process on a non-default VRF and enter OSPFv3 mode.
PAGE 625
● Specify whether some or all some of the interfaces are passive. CONF-IPV6-ROUTER-OSPF mode passive-interface {interface-type} Interface: identifies the specific interface that is passive. ○ ○ ○ ○ For For For For a a a a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. port channel interface, enter the keywords port-channel then a number.
PAGE 626
By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA. To enable OSPFv3 graceful restart, enter the ipv6 router ospf process-id command to enter OSPFv3 configuration mode. Then configure a grace period using the graceful-restart grace-period command. The grace period is the time that the OSPFv3 neighbors continue to advertise the restarting router as though it is fully adjacent.
PAGE 627
The following example shows the show run ospf command. DellEMC#show run ospf ! router ospf 1 router-id 200.1.1.1 log-adjacency-changes graceful-restart grace-period 180 network 20.1.1.0/24 area 0 network 30.1.1.0/24 area 0 ! ipv6 router ospf 1 log-adjacency-changes graceful-restart grace-period 180 The following example shows the show ipv6 ospf database database-summary command. DellEMC#show ipv6 ospf database database-summary ! OSPFv3 Router with ID (200.1.1.
PAGE 628
IPsec is a set of protocols developed by the internet engineering task force (IETF) to support secure exchange of packets at the IP layer. IPsec supports two encryption modes: transport and tunnel. ● Transport mode — encrypts only the data portion (payload) of each packet, but leaves the header untouched. ● Tunnel mode — is more secure and encrypts both the header and payload. On the receiving side, an IPsec-compliant device decrypts each packet.
PAGE 629
NOTE: To encrypt all keys on a router, use the service password-encryption command in Global Configuration mode. However, this command does not provide a high level of network security. To enable key encryption in an IPsec security policy at an interface or area level, specify 7 for [key-encryption-type] when you enter the ipv6 ospf authentication ipsec or ipv6 ospf encryption ipsec command.
PAGE 630
● Enable IPsec encryption for OSPFv3 packets on an IPv6-based interface. INTERFACE mode ipv6 ospf encryption {null | ipsec spi number esp encryption-algorithm [key-encryptiontype] key authentication-algorithm [key-authentication-type] key} ○ null: causes an encryption policy configured for the area to not be inherited on the interface. ○ ipsec spi number: is the security policy index (SPI) value. The range is from 256 to 4294967295.
PAGE 631
no area area-id authentication ipsec spi number ● Display the configuration of IPSec authentication policies on the router. show crypto ipsec policy Configuring IPsec Encryption for an OSPFv3 Area To configure, remove, or display IPsec encryption in an OSPFv3 area, use the following commands. Prerequisite: Before you enable IPsec encryption in an OSPFv3 area, first enable OSPFv3 globally on the router (refer to Configuration Task List for OSPFv3 (OSPF for IPv6)).
PAGE 632
● Display security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router. EXEC Privilege show crypto ipsec sa ipv6 [interface interface] To display information on the SAs used on a specific interface, enter interface interface, where interface is one of the following values: ○ ○ ○ ○ For For For For a a a a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 633
STATUS : ACTIVE outbound ah sas spi : 500 (0x1f4) transform : ah-md5-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE inbound esp sas outbound esp sas Interface: TenGigabitEthernet 1/2 Link Local address: fe80::201:e8ff:fe40:4d11 IPSecv6 policy name: OSPFv3-1-600 inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) tran
PAGE 634
show ipv6 route [vrf vrf-name] summary ● View the summary information for the OSPFv3 database. EXEC Privilege mode show ipv6 ospf [vrf vrf-name] database ● View the configuration of OSPFv3 neighbors. EXEC Privilege mode show ipv6 ospf [vrf vrf-name] neighbor ● View debug messages for all OSPFv3 interfaces.
PAGE 635
SNMPv2-SMI::mib-2.191.1.1.5.0 = INTEGER: 2 SNMPv2-SMI::mib-2.191.1.1.6.0 = Gauge32: 0 SNMPv2-SMI::mib-2.191.1.1.7.0 = Gauge32: 0 SNMPv2-SMI::mib-2.191.1.1.8.0 = Counter32: 10088 SNMPv2-SMI::mib-2.191.1.1.9.0 = Counter32: 10076 SNMPv2-SMI::mib-2.191.1.1.10.0 = Gauge32: 7 SNMPv2-SMI::mib-2.191.1.1.11.0 = INTEGER: -1 SNMPv2-SMI::mib-2.191.1.1.12.0 = Gauge32: 0 SNMPv2-SMI::mib-2.191.1.1.13.0 = INTEGER: 2 SNMPv2-SMI::mib-2.191.1.1.14.0 = Gauge32: 100000 SNMPv2-SMI::mib-2.191.1.1.15.
PAGE 636
35 Policy-based Routing (PBR) Policy-based routing (PBR) allows a switch to make routing decisions based on policies applied to an interface. Topics: • • • • Overview Implementing PBR Configuration Task List for Policy-based Routing Sample Configuration Overview When a router receives a packet, the router decides where to forward the packet based on the destination address in the packet, which is used to look up an entry in a routing table.
PAGE 637
● ● ● ● Destination IP address and mask Source port Destination port TCP Flags After you apply a redirect-list to an interface, all traffic passing through it is subjected to the rules defined in the redirect-list. Traffic is forwarded based on the following: ● ● ● ● Next-hop addresses are verified. If the specified next hop is reachable, traffic is forwarded to the specified next-hop. If the specified next-hops are not reachable, the normal routing table is used to forward the traffic.
PAGE 638
PBR Exceptions (Permit) To create an exception to a redirect list, use thepermit command. Exceptions are used when a forwarding decision should be based on the routing table rather than a routing policy. The Dell EMC Networking OS assigns the first available sequence number to a rule configured without a sequence number and inserts the rule into the PBR CAM region next to the existing entries. Because the order of rules is important, ensure that you configure any necessary sequence numbers.
PAGE 639
● ● ● ● source ip-address or any or host ip-address is the Source’s IP address FORMAT: A.B.C.D/NN, or ANY or HOST IP address destination ip-address or any or host ip-address is the Destination’s IP address FORMAT: A.B.C.D/NN, or ANY or HOST IP address To delete a rule, use the no redirect command.
PAGE 640
multiple seq redirect commands with the same source and destination address and specify a different next-hop IP address. In this way, the recursive routes are used as different forwarding routes for dynamic failover. If the primary path goes down and the recursive route is removed from the routing table, the seq redirect command is ignored and the next command in the list with a different route is used.
PAGE 641
In addition to supporting multiple redirect-lists in a redirect-group, multiple redirect-groups are supported on a single interface. Dell EMC Networking OS has the capability to support multiple groups on an interface for backup purposes. Show Redirect List Configuration To view the configuration redirect list configuration, use the following commands. 1. View the redirect list configuration and the associated interfaces. EXEC mode show ip redirect-list redirect-list-name 2.
PAGE 642
Example: Showing CAM PBR Configuration DellEMC#show cam pbr stack-unit 1 port-set 0 TCP Flag: Bit 5 - URG, Bit 4 - ACK, Bit 3 - PSH, Bit 2 - RST, Bit 1 - SYN, Bit 0 - FIN Cam Port VlanID Proto Tcp Src Dst SrcIp DstIp Next-hop Egress Index Flag Port Port MAC Port ---------------------------------------------------------------------------------------------------------------06080 0 N/A IP 0x0 0 0 200.200.200.200 200.200.200.200 199.199.199.199 199.199.199.199 N/A NA 06081 0 N/A TCP 0x10 0 40 234.234.234.
PAGE 643
Create the Redirect-List GOLD EDGE_ROUTER(conf-if-Te-2/23)#ip redirect-list GOLD EDGE_ROUTER(conf-redirect-list)#description Route GOLD traffic to ISP_GOLD. EDGE_ROUTER(conf-redirect-list)#direct 10.99.99.254 ip 192.168.1.0/24 any EDGE_ROUTER(conf-redirect-list)#redirect 10.99.99.254 ip 192.168.2.0/24 any EDGE_ROUTER(conf-redirect-list)# seq 15 permit ip any any EDGE_ROUTER(conf-redirect-list)#show config ! ip redirect-list GOLD description Route GOLD traffic to ISP_GOLD. seq 5 redirect 10.99.99.254 ip 192.
PAGE 644
144.144.144.144 DellEMC(conf-redirect-list)#end Verify the Status of the Track Objects (Up/Down): DellEMC#show track brief ResId 1 2 3 4 Resource Interface ip routing Interface ipv6 routing IP Host reachability IP Host reachability Parameter Tunnel 1 Tunnel 2 42.1.1.2/32 43.1.1.
PAGE 645
Create Track Objects to track the Tunnel Interfaces: DellEMC#configure terminal DellEMC(conf)#track 1 interface tunnel 1 ip routing DellEMC(conf-track-1)#exit DellEMC(conf)#track 2 interface tunnel 2 ipv6 routing DellEMC(conf-track-2)#end Verify the Status of the Track Objects (Up/Down): DellEMC#show track brief ResId Resource 1 Interface ip routing 2 Interface ipv6 routing DellEMC# Parameter Tunnel 1 Tunnel 2 State Up Up LastChange 00:00:00 00:00:00 Create a Redirect-list with Track Objects pertaining
PAGE 646
36 PIM Sparse-Mode (PIM-SM) Protocol-independent multicast sparse-mode (PIM-SM) is a multicast protocol that forwards multicast traffic to a subnet only after a request using a PIM Join message; this behavior is the opposite of PIM-Dense mode, which forwards multicast traffic to all subnets until a request to stop.
PAGE 647
3. If a host on the same subnet as another multicast receiver sends an IGMP report for the same multicast group, the gateway takes no action. If a router between the host and the RP receives a PIM Join message for which it already has a (*,G) entry, the interface on which the message was received is added to the outgoing interface list associated with the (*,G) entry, and the message is not (and does not need to be) forwarded towards the RP.
PAGE 648
Related Configuration Tasks The following are related PIM-SM configuration tasks. ● ● ● ● Configuring S,G Expiry Timers Configuring a Static Rendezvous Point Configuring a Designated Router Creating Multicast Boundaries and Domains Enable PIM-SM You must enable PIM-SM on each participating interface. 1. Enable IPv4 multicast routing on the system. CONFIGURATION mode ip multicast-routing [vrf vrf-name] 2. Enable PIM-Sparse mode.
PAGE 649
127.87.50.5 DellEMC# Te 2/13 00:03:08/00:01:37 v2 1 / S DellEMC#show ipv6 pim neighbor Neighbor Interface Uptime/Expires Address fe80::201:e8ff:fe02:140f Te 1/11 01:44:59/00:01:16 fe80::201:e8ff:fe00:6265 Te 1/12 01:45:00/00:01:16 DellEMC# Ver v2 v2 DR Prio/Mode 1 / S 1 / DR To display the PIM routing table, use the show ip pim tib [group-address [source-address]] command from EXEC privilege mode.
PAGE 650
ip pim sparse-mode sg-expiry-timer seconds The range is from 211 to 86,400 seconds. The default is 210. NOTE: The global expiry time for all [S, G] entries can vary from 360 to 420 seconds. Configuring a Static Rendezvous Point The rendezvous point (RP) is a PIM-enabled interface on a router that acts as the root a group-specific tree; every group must have an RP. ● Identify an RP by the IP address of a PIM-enabled or Loopback interface.
PAGE 651
● Change the interval at which a router sends hello messages. INTERFACE mode ip pim query-interval seconds ● Display the current value of these parameter.
PAGE 652
Creating Multicast Boundaries and Domains A PIM domain is a contiguous set of routers that all implement PIM and are configured to operate within a common boundary defined by PIM multicast border routers (PMBRs). PMBRs connect each PIM domain to the rest of the Internet. Create multicast boundaries and domains by filtering inbound and outbound bootstrap router (BSR) messages per interface. The following command is applied to the subsequent inbound and outbound updates.
PAGE 653
37 PIM Source-Specific Mode (PIM-SSM) PIM source-specific mode (PIM-SSM) is a multicast protocol that forwards multicast traffic from a single source to a subnet. In the other versions of protocol independent multicast (PIM), a receiver subscribes to a group only. The receiver receives traffic not just from the source in which it is interested but from all sources sending to that group.
PAGE 654
Related Configuration Tasks ● Use PIM-SSM with IGMP Version 2 Hosts Enabling PIM-SSM To enable PIM-SSM, follow these steps. 1. Create an ACL that uses permit rules to specify what range of addresses should use SSM. CONFIGURATION mode ip access-list standard name 2. Enter the ip pim ssm-range command and specify the ACL you created. CONFIGURATION mode ip pim ssm-range acl-name To display address ranges in the PIM-SSM range, use the show ip pim ssm-range command from EXEC Privilege mode.
PAGE 655
Configuring PIM-SSM with IGMPv2 R1(conf)#do show run pim ! ip pim rp-address 10.11.12.2 group-address 224.0.0.0/4 ip pim ssm-range ssm R1(conf)#do show run acl ! ip access-list standard map seq 5 permit host 239.0.0.2 ! ip access-list standard ssm seq 5 permit host 239.0.0.2 R1(conf)#ip igmp ssm-map map 10.11.5.2 R1(conf)#do show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface Mode Uptime Expires 239.0.0.
PAGE 656
Group Address Interface Mode Uptime 239.0.0.2 Vlan 300 IGMPv2-Compat 00:00:36 Member Ports: Te 1/1 R1(conf)#do show ip igmp ssm-map 239.0.0.2 SSM Map Information Group : 239.0.0.2 Source(s) : 10.11.5.2 R1(conf)#do show ip igmp groups detail Interface Group Uptime Expires Router mode Last reporter Last reporter mode Last report Group source Source address 10.11.5.2 00:00:01 Expires Never Last Reporter 10.11.3.2 Vlan 300 239.0.0.2 00:00:01 Never IGMPv2-Compat 10.11.3.
PAGE 657
To enable BSR election for IPv4 or IPv6, perform the following steps: 1. Enter the following IPv4 or IPv6 command to make a PIM router a BSR candidate: CONFIGURATION ip pim bsr-candidate ipv6 pim bsr-candidate 2. Enter the following IPv4 or IPv6 command to make a PIM router a RP candidate: CONFIGURATION ip pim rp-candidate ipv6 pim rp-candidate 3. Display IPv4 or IPv6 Bootstrap Router information.
PAGE 658
NOTE: You can create the ACL list of multicast prefix using the ip access-list standard command.
PAGE 659
38 Port Monitoring Port monitoring (also referred to as mirroring ) allows you to monitor ingress and/or egress traffic on specified ports. The mirrored traffic can be sent to a port to which a network analyzer is connected to inspect or troubleshoot the traffic. Mirroring is used for monitoring Ingress or Egress or both Ingress and Egress traffic on a specific port(s). This mirrored traffic can be sent to a port where a network sniffer can connect and monitor the traffic.
PAGE 660
Port Monitoring Port monitoring is supported on both physical and logical interfaces, such as VLAN and port-channel interfaces. The source port (MD) with monitored traffic and the destination ports (MG) to which an analyzer can be attached must be on the same switch. You can configure up to 128 source ports in a monitoring session. Only one destination port is supported in a monitoring session. The platform supports multiple source-destination statements in a single monitor session.
PAGE 661
Example of Configuring Another Monitoring Session with a Previously Used Destination Port DellEMC(conf)#monitor session 300 DellEMC(conf-mon-sess-300)#source TenGig 1/17 destination TenGig 1/4 direction tx % Error: Exceeding max MG ports for this MD port pipe.
PAGE 662
the configuration source TenGig 6/1 destination TeGig 6/2 direction tx, if the MD port TenGig 6/1 is an untagged member of any VLAN, all monitored frames that the MG port TeGig 6/2 receives are tagged with the VLAN ID of the MD port. Similarly, if BPDUs are transmitted, the MG port receives them tagged with the VLAN ID 4095. This behavior might result in a difference between the number of egress packets on the MD port and monitored packets on the MG port.
PAGE 663
N/A N/A N/A 0 0 1 Te 1/1 N/A Po 10 N/A Vl 40 N/A Te 1/2 No Te 1/2 No Te 1/3 No rx Port 0.0.0.0 0.0.0.0 0 0 No rx Port 0.0.0.0 0.0.0.0 0 0 No rx Flow 0.0.0.0 0.0.0.0 0 0 No NOTE: Source as VLAN is achieved via Flow based mirroring. Please refer section Enabling Flow-Based Monitoring. In the following example, the host and server are exchanging traffic which passes through the uplink interface 1/1.
PAGE 664
Flow-Based Monitoring Flow-based monitoring conserves bandwidth by monitoring only the specified traffic instead of all traffic on the interface. It is available for Layer 3 ingress traffic. You can specify the traffic that needs to be monitored using standard or extended accesslists. The flow-based monitoring mechanism copies packets that matches the ACL rules applied on the port and forwards (mirrors) them to another port.
PAGE 665
---- ------ -------------1 Te 1/2 remote-ip 0 0 No N/A N/A DellEMC# --------rx Port yes 0.0.0.0 0.0.0.0 The show config command has been modified to display monitoring configuration in a particular session. Example Output of the show Command The show ip accounting commands have been enhanced to display whether monitoring is enabled for traffic that matches with the rules of the specific ACL.
PAGE 666
DellEMC(conf)#ip access-list ext testflow DellEMC(config-ext-nacl)#seq 5 permit icmp any any count bytes monitor DellEMC(config-ext-nacl)#seq 10 permit ip 102.1.1.
PAGE 667
ACL. The IPv6 mirror ACL region priority is less than IPv6 user ACL region, so that the traffic matching the user ACL takes priority in permit/deny action. Both IPv4 and IPv6 mirror ACLs can co-exist in a monitor session. Pre-requisite ● Allocate a CAM region using the following command.
PAGE 668
DellEMC#show monitor session 10 Monitor session – 10 Interface Direction ----------------Te 1/1 rx access-list Mirror-access-list -----------------mtv6acl(ipv6) The following show cam-acl output displays the CAM region ipv6mirraclconfigured for IPv6 flow-based mirroring with ACL.
PAGE 669
Remote Port Mirroring Example Remote port mirroring uses the analyzers shown in the aggregation network in Site A. The VLAN traffic on monitored links from the access network is tagged and assigned to a dedicated L2 VLAN. Monitored links are configured in two source sessions shown with orange and green circles. Each source session uses a separate reserved VLAN to transmit mirrored packets (mirrored source-session traffic is shown with an orange or green circle with a blue border).
PAGE 670
● Mirrored traffic is transported across the network using 802.1Q-in-802.1Q tunneling. The source address, destination address and original VLAN ID of the mirrored packet are preserved with the tagged VLAN header. Untagged source packets are tagged with the reserve VLAN ID. ● You cannot configure a private VLAN or a GVRP VLAN as the reserved RPM VLAN. ● The RPM VLAN can’t be a Private VLAN. ● The RPM VLAN can be used as GVRP VLAN. ● The L3 interface configuration should be blocked for RPM VLAN.
PAGE 671
● A destination port for remote port mirroring cannot be used as a source port, including the session in which the port functions as the destination port. ● A destination port cannot be used in any spanning tree instance. ● The reserved VLAN used to transport mirrored traffic must be a L2 VLAN. L3 VLANs are not supported. ● On a source switch on which you configure source ports for remote port mirroring, you can add only one port to the dedicated RPM VLAN which is used to transport mirrored traffic.
PAGE 672
Configuring a RSPAN VLAN for RPM Following are the steps for configuring a RSPAN VLAN for RPM. You must repeat the below mentioned steps on source, intermediate, and destination switches. 1. Enter global configuration mode. EXEC mode configure terminal 2. Create a VLAN to transport mirrored traffic in RPM. CONFIGURATION mode interface vlan vlan-id 3. Configure the RSPAN VLAN to be used to transport mirrored traffic in RPM. VLAN INTERFACE mode mode remote-port-mirroring 4.
PAGE 673
MONITOR SESSION mode tagged destination interface To configure destination ports as untagged ports, enter the untagged destinationcommand. Configuration Example of Remote Port Mirroring This example provides a sample configuration of remote port mirroring (RPM) on a source switch, an intermediate switch, and a destination switch based on the following illustration. Figure 105.
PAGE 674
DellEMC(conf-if-vl-10)#tagged tengigabitethernet 1/5 DellEMC(conf-if-vl-10)#exit Configuring Remote Port Mirroring on a destination switch Following is a sample configuration of RPM on an a destination switch.
PAGE 675
Dell(conf-mon-sess-2)#source remote-vlan 20 destination tengigabitethernet 1/8 Dell(conf-mon-sess-2)#tagged destination tengigabitethernet 1/8 Dell(conf-mon-sess-2)#exit Configuration Example of RPM for port-channel This example provides a sample configuration of remote port mirroring for the port-channel source interface.
PAGE 676
Encapsulated Remote Port Monitoring Encapsulated Remote Port Monitoring (ERPM) copies traffic from source ports/port-channels or source VLANs and forwards the traffic using routable GRE-encapsulated packets to the destination IP address specified in the session. NOTE: When configuring ERPM, follow these guidelines ● The Dell EMC Networking OS supports ERPM source session only. Encapsulated packets terminate at the destination IP address or at the analyzer.
PAGE 677
The following example shows an ERPM configuration: DellEMC(conf)#monitor session 0 type erpm DellEMC(conf-mon-sess-0)#source tengigabitethernet 1/9 direction rx DellEMC(conf-mon-sess-0)#source port-channel 1 direction tx DellEMC(conf-mon-sess-0)#erpm source-ip 1.1.1.1 dest-ip 7.1.1.2 gre-protocol 111 DellEMC(conf-mon-sess-0)#no disable DellEMC(conf)#monitor session 1 type erpm DellEMC(conf-mon-sess-1)#source vlan 11 direction rx DellEMC(conf-mon-sess-1)#erpm source-ip 5.1.1.1 dest-ip 3.1.1.
PAGE 678
ERPM Behavior on a typical Dell EMC Networking OS The Dell EMC Networking OS is designed to support only the Encapsulation of the data received / transmitted at the specified source port (Port A). An ERPM destination session / decapsulation of the ERPM packets at the destination Switch are not supported. Figure 106.
PAGE 679
○ Either have a Linux server's ethernet port ip as the ERPM destination ip or connect the ingress interface of the server to the ERPM MirrorToPort. The analyzer should listen in the forward/egress interface. If there is only one interface, one can choose the ingress and forward interface to be same and listen in the tx direction of the interface. ○ Download/ Write a small script (for example: erpm.py) such that it will strip the given ERPM packet starting from the bit where GRE header ends.
PAGE 680
VLT Fail-over Scenario Consider a scenario where port monitoring is configured to mirror traffic on the source port or LAG of a VLT device to a destination port on an other device on the network. A fail-over occurs when the primary VLT device fails causing the secondary VLT device to take over. At the time of failover, the mirrored packets are dropped for some time. This time period is equivalent to the gracious VLT failover recovery time.
PAGE 681
Table 72. RPM over VLT Scenarios (continued) Scenario RPM Restriction Recommended Solution device:source remote vlan destination orphan port. Mirroring VLT LAG across VLT Peers — In this scenario, the VLT LAG on the primary VLT peer is mirrored to an orphan port on the secondary VLT peer through the ICL LAG. The packet analyzer is connected to the secondary VLT peer. No restrictions apply to the RPM session.
PAGE 682
39 Per-VLAN Spanning Tree Plus (PVST+) Per-VLAN spanning tree plus (PVST+) is a variation of spanning tree — developed by a third party — that allows you to configure a separate spanning tree instance for each virtual local area network (VLAN).
PAGE 683
Figure 107. Per-VLAN Spanning Tree The Dell EMC Networking OS supports three other variations of spanning tree, as shown in the following table. Table 73. Spanning Tree Variations Dell EMC Networking OS Supports Dell EMC Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .1w Multiple Spanning Tree Protocol (MSTP) 802 .
PAGE 684
Configure Per-VLAN Spanning Tree Plus Configuring PVST+ is a four-step process. 1. 2. 3. 4. Configure interfaces for Layer 2. Place the interfaces in VLANs. Enable PVST+. Optionally, for load balancing, select a nondefault bridge-priority for a VLAN.
PAGE 685
Influencing PVST+ Root Selection As shown in the previous per-VLAN spanning tree illustration, all VLANs use the same forwarding topology because R2 is elected the root, and all TenGigabitEthernet ports have the same cost. The following per-VLAN spanning tree illustration changes the bridge priority of each bridge so that a different forwarding topology is generated for each VLAN. This behavior demonstrates how you can use PVST+ to achieve load balancing. Figure 108.
PAGE 686
Current root has priority 4096, Address 0001.e80d.b6d6 Number of topology changes 5, last change occurred 00:34:37 ago on Te 1/32 Port 375 (TenGigabitEthernet 1/22) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.375 Designated root has priority 4096, address 0001.e80d.b6:d6 Designated bridge has priority 4096, address 0001.e80d.b6:d6 Designated port id is 128.
PAGE 687
● Port priority — influences the likelihood that a port is selected to be a forwarding port in case that several ports have the same port cost. The following tables lists the default values for port cost by interface. Table 74.
PAGE 688
CAUTION: Configure EdgePort only on links connecting to an end station. EdgePort can cause loops if you enable it on an interface connected to a network. To enable EdgePort on an interface, use the following command. ● Enable EdgePort on an interface. INTERFACE mode spanning-tree pvst edge-port [bpduguard | shutdown-on-violation] The EdgePort status of each interface is given in the output of the show spanning-tree pvst command, as previously shown.
PAGE 689
Figure 109. PVST+ with Extend System ID ● Augment the bridge ID with the VLAN ID. PROTOCOL PVST mode extend system-id DellEMC(conf-pvst)#do show spanning-tree pvst vlan 5 brief VLAN 5 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32773, Address 0001.e832.73f7 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32773 (priority 32768 sys-id-ext 5), Address 0001.e832.
PAGE 690
no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/22,32 no shutdown ! protocol spanning-tree pvst no disable vlan 100 bridge-priority 4096 Example of PVST+ Configuration (R2) interface TenGigabitEthernet 2/12 no ip address switchport no shutdown ! interface TenGigabitEthernet 2/32 no ip address switchport no shutdown ! interface Vlan 100 no ip address tagged TenGigabitEthernet 2/12,32 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 2/12,32 no shutdown ! inte
PAGE 691
40 Quality of Service (QoS) This chapter describes how to use and configure Quality of Service service (QoS) features on the switch. Differentiated service is accomplished by classifying and queuing traffic, and assigning priorities to those queues. Table 75.
PAGE 692
Table 75. Dell EMC Networking Operating System (OS) Support for Port-Based, Policy-Based Features (continued) Feature Direction Create Output Policy Maps Egress Specify an Aggregate QoS Policy Egress Create Output Policy Maps Egress Enabling QoS Rate Adjustment Enabling Strict-Priority Queueing Weighted Random Early Detection Egress Create WRED Profiles Egress Figure 110.
PAGE 693
• • • • • • Configuring Policy-Based Rate Shaping Configuring Weights and ECN for WRED Configuring WRED and ECN Attributes Guidelines for Configuring ECN for Classifying and Color-Marking Packets Applying Layer 2 Match Criteria on a Layer 3 Interface Enabling Buffer Statistics Tracking Implementation Information The Dell EMC Networking QoS implementation complies with IEEE 802.1p User Priority Bits for QoS Indication.
PAGE 694
dot1p-priority DellEMC#configure terminal DellEMC(conf)#interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)#switchport DellEMC(conf-if-te-1/1)#dot1p-priority 1 DellEMC(conf-if-te-1/1)#end Honoring dot1p Priorities on Ingress Traffic By default, Dell EMC Networking OS does not honor dot1p priorities on ingress traffic. You can configure this feature on physical interfaces and port-channels, but you cannot configure it on individual interfaces in a port channel.
PAGE 695
Traffic Monitor 0: normal 300 (50) peak 800 (50) Out of profile yellow 23386960 red 320605113 Traffic Monitor 1: normal NA peak NA Out of profile yellow 0 red 0 Traffic Monitor 2: normal NA peak NA Out of profile yellow 0 red 0 Traffic Monitor 3: normal NA peak NA Out of profile yellow 0 red 0 Traffic Monitor 4: normal NA peak NA Out of profile yellow 0 red 0 Configuring Port-Based Rate Shaping Rate shaping buffers, rather than drops, traffic exceeding the specified rate until the buffer is exhausted.
PAGE 696
Policy-Based QoS Configurations Policy-based QoS configurations consist of the components shown in the following example. Figure 111. Constructing Policy-Based QoS Configurations Classify Traffic Class maps differentiate traffic so that you can apply separate quality of service policies to different types of traffic. For both class maps, Layer 2 and Layer 3, Dell EMC Networking OS matches packets against match criteria in the order that you configure them.
PAGE 697
class-map match-any 2. Create a match-all class map. CONFIGURATION mode class-map match-all 3. Specify your match criteria. CLASS MAP mode [seq sequence number] match {ip | ipv6 | ip-any} After you create a class-map, Dell EMC Networking OS places you in CLASS MAP mode. Match-any class maps allow up to five ACLs. Match-all class-maps allow only one ACL. NOTE: Within a class-map, the match rules are installed in the sequence number order. 4. Link the class-map to a queue.
PAGE 698
3. Specify your match criteria. CLASS MAP mode [seq sequence number] match mac After you create a class-map, Dell EMC Networking OS places you in CLASS MAP mode. Match-any class maps allow up to five access-lists. Match-all class-maps allow only one. You can match against only one VLAN ID. 4. Link the class-map to a queue.
PAGE 699
ip access-list extended AF1-FB1 seq 5 permit ip host 23.64.0.2 any seq 10 deny ip any any ! ip access-list extended AF1-FB2 seq 5 permit ip host 23.64.0.3 any seq 10 deny ip any any ! ip access-list extended AF2 seq 5 permit ip host 23.64.0.5 any seq 10 deny ip any any DellEMC# show cam layer3-qos interface tengigabitethernet 2/4 Cam Port Dscp Proto Tcp Src Dst SrcIp DstIp DSCP Queue Index Flag Port Port Marking ----------------------------------------------------------------------20416 1 18 IP 0x0 0 0 23.
PAGE 700
● If two rate three color policer is configured along with this feature then, ○ x < CIR – will be marked as “Green” ○ CIR < x< PIR – will be marked as “Yellow” ○ PIR < x – will be marked as “Red” But ‘Green’ packets matching the specific match criteria for which ‘color-marking’ is configured will be over-written and marked as “Yellow”. Create a QoS Policy There are two types of QoS policies — input and output. Input QoS policies regulate Layer 3 and Layer 2 ingress traffic.
PAGE 701
set mac-dot1p Constraints The systems supporting this feature should use only the default global dot1p to queue mapping configuration as described in Dot1p to Queue Mapping Requirement. Creating an Output QoS Policy To create an output QoS policy, use the following commands. 1. Create an output QoS policy. CONFIGURATION mode qos-policy-output 2.
PAGE 702
When you assign a percentage to one queue, note that this change also affects the amount of bandwidth that is allocated to other queues. Therefore, whenever you are allocating bandwidth to one queue, Dell EMC Networking recommends evaluating your bandwidth requirements for all other queues as well. ● Assign each queue a bandwidth percentage ranging from 1 to 100%, in increments of 1%.
PAGE 703
● All DSCP values that are not specified as yellow or red are colored green (low drop precedence). ● A DSCP value cannot be in both the yellow and red lists. Setting the red or yellow list with any DSCP value that is already in the other list results in an error and no update to that DSCP list is made. ● Each color map can only have one list of DSCP values for each color; any DSCP values previously listed for that color that are not in the new DSCP list are colored green.
PAGE 704
Displaying a DSCP Color Policy Configuration To display the DSCP color policy configuration for one or all interfaces, use the show qos dscp-color-policy {summary [interface] | detail {interface}} command in EXEC mode. summary: Displays summary information about a color policy on one or more interfaces. detail: Displays detailed color policy information on an interface interface : Enter the name of the interface that has the color policy configured.
PAGE 705
Applying an Input QoS Policy to an Input Policy Map To apply an input QoS policy to an input policy map, use the following command. ● Apply an input QoS policy to an input policy map. POLICY-MAP-IN mode policy-service-queue qos-polcy Honoring DSCP Values on Ingress Packets Dell EMC Networking OS provides the ability to honor DSCP values on ingress packets using Trust DSCP feature.
PAGE 706
Table 79. Default dot1p to Queue Mapping (continued) dot1p Queue ID 7 7 The dot1p value is also honored for frames on the default VLAN. For more information, refer to Priority-Tagged Frames on the Default VLAN. ● Enable the trust dot1p feature. POLICY-MAP-IN mode trust dot1p Mapping dot1p Values to Service Queues All traffic is by default mapped to the same queue, Queue 0.
PAGE 707
policy-map-output 2. After you create an output policy map, do one or more of the following: Applying an Output QoS Policy to a Queue Specifying an Aggregate QoS Policy Applying an Output Policy Map to an Interface 3. Apply the policy map to an interface. Applying an Output QoS Policy to a Queue To apply an output QoS policy to a queue, use the following command. ● Apply an output QoS policy to queues.
PAGE 708
For example, to include the Preamble and SFD, type qos-rate-adjust 8. For variable length overhead fields, know the number of bytes you want to include. The default is disabled. Enabling Strict-Priority Queueing In strict-priority queuing, the system de-queues all packets from the assigned queue before servicing any other queues. You can assign strict-priority to one unicast queue, using the strict-priority command.
PAGE 709
NOTE: L2 qos-policy behavior will be retained and would not be changed, that is we would not allow to set both DSCP and Dot1p in the L2 Input Qos Policy. Example case: Consider that two switches A and B are connected back to back via a tagged interface. Consider the case where untagged packets arrive on switch A, if you want to generate PFC for priority 2 for DSCP range 0-7, then you must need to match the interested traffic using the class map.
PAGE 710
Figure 112. Packet Drop Rate for WRED You can create a custom WRED profile or use one of the five pre-defined profiles. Enabling and Disabling WRED Globally By default, WRED is enabled on the system. You can disable or reenable WRED manually using a single command. Follow these steps to disable or enable WRED in Dell EMC Networking OS.
PAGE 711
Applying a WRED Profile to Traffic After you create a WRED profile, you must specify to which traffic Dell EMC Networking OS should apply the profile. Dell EMC Networking OS assigns a color (also called drop precedence) — red, yellow, or green — to each packet based on it DSCP value before queuing it. DSCP is a 6–bit field. Dell EMC Networking uses the first three bits (LSB) of this field (DP) to determine the drop precedence. ● DP values of 110 and 100, 101 map to yellow; all other values map to green.
PAGE 712
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 UCAST 1708252734 2340972 874625399808 1198000301 1357413570 0 694995747840 4 UCAST 0 0 0 0 0 0 0 5 UCAST 0 0 0 0 0 0 0 6 UCAST 0 0 0 0 0 0 0 7 UCAST 0 0 0 0 0 0 0 8 UCAST 0 0 0 0 0 0 0 9 UCAST 1132 1 143063 217 0 0 0 10 MCAST 0 0 0 0 0 0 0 11 MCAST 0 0 0 0 0 0 0 12 MCAST 0 0 0 0 0 0 0 13 MCAST 0 0 0 0 0 0 0 14 MCAST 0 0 0 0 0 0 0 15 MCAST 0 0 0 0 0 0 0 16 MCA
PAGE 713
CAM entries the policy-map would consume; the test cam-usage command is useful because it provides this measurement. ● Verify that there are enough available CAM entries.
PAGE 714
QOS-POLICY-OUT mode DellEMC(config-qos-policy-out)# rate shape pps peak-rate burst-packets committed pps committed-rate burst-packets 4. Alternatively, configure the committed rate and committed burst size in bytes.
PAGE 715
● If WRED/ECN is enabled on the global service-pool with threshold values and if it is not enabled on the queues, WRED/ECN are not effective based on global service-pool WRED thresholds. The queue on which the traffic is scheduled must contain WRED/ECN settings, which are enabled for WRED, to be valid for that traffic.
PAGE 716
WRED mode DellEMC(conf-wred) #wred—profile thresh-1 DellEMC(conf-wred) #threshold min 100 max 200 max-drop-rate 40 3. Configure another WRED profile, and specify the threshold and maximum drop rate. WRED mode DellEMC(conf-wred) #wred—profile thresh-2 DellEMC(conf-wred) #threshold min 300 max 400 max-drop-rate 80 4. Create a global buffer pool that is a shared buffer pool accessed by multiple queues when the minimum guaranteed buffers for the queue are consumed.
PAGE 717
Sample configuration to mark non-ecn packets as “yellow” with Multiple traffic class Consider the example where there are no different traffic classes that is all the packets are egressing on the default ‘queue0’. Dell EMC Networking OS can be configured as below to mark the non-ecn packets as yellow packets.
PAGE 718
categorization. The IPv4 ACLs (standard and Extended) are enhanced to add this qualifier. This new keyword ‘ecn’ is present for all L3 ACL types (TCP/UDP/IP/ICMP) at the level where the ‘DSCP’ qualifier is positioned in the current ACL commands. Dell EMC Networking OS supports the capability to contain DSCP and ECN classifiers simultaneously for the same ACL entry.
PAGE 719
Approach without explicit ECN match qualifiers for ECN packets: ! ip access-list standard dscp_50 seq 5 permit any dscp 50 ! ip access-list standard dscp_40 seq 5 permit any dscp 40 ! ip access-list standard dscp_50_non_ecn seq 5 permit any dscp 50 ecn 0 ! ip access-list standard dscp_40_non_ecn seq 5 permit any dscp 40 ecn 0 ! class-map match-any class_dscp_40 match ip access-group dscp_40_non_ecn set-color yellow match ip access-group dscp_40 ! class-map match-any class_dscp_50 match ip access-group dscp_
PAGE 720
Applying Layer 2 Match Criteria on a Layer 3 Interface To process Layer 3 packets that contain a dot1p (IEEE 802.1p) VLAN Layer 2 header, configure VLAN tags on a Layer 3 port interface which is configured with an IP address but has no VLAN associated with it. You can also configure a VLAN subinterface on the port interface and apply a policy map that classifies packets using the dot1p VLAN ID.
PAGE 721
Enabling Buffer Statistics Tracking You can enable the tracking of statistical values of buffer spaces at a global level. The buffer statistics tracking utility operates in the max use count mode that enables the collection of maximum values of counters. To configure the buffer statistics tracking utility, perform the following step: 1. Enable the buffer statistics tracking utility and enter the Buffer Statistics Snapshot configuration mode.
PAGE 722
Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 29 (interface Fo 1/172) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 33 (interface Fo 1/176) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 37 (interface Fo 1/180) --------------------------------------Q# TYPE Q# TOTAL BUFFER
PAGE 723
41 Routing Information Protocol (RIP) The Routing Information Protocol (RIP) tracks distances or hop counts to nearby routers when establishing network connections and is based on a distance-vector algorithm. RIP is based on a distance-vector algorithm; it tracks distances or hop counts to nearby routers when establishing network connections. RIP protocol standards are listed in the Standards Compliance chapter.
PAGE 724
Table 81. RIP Defaults Feature Default Interfaces running RIP ● Listen to RIPv1 and RIPv2 ● Transmit RIPv1 RIP timers ● ● ● ● Auto summarization Enabled ECMP paths supported 16 update timer = 30 seconds invalid timer = 180 seconds holddown timer = 180 seconds flush timer = 240 seconds Configuration Information By default, RIP is disabled in Dell EMC Networking OS. To configure RIP, you must use commands in two modes: ROUTER RIP and INTERFACE.
PAGE 725
The Dell EMC Networking OS default is to send RIPv1 and to receive RIPv1 and RIPv2. To change the RIP version globally, use the version command in ROUTER RIP mode. To view the global RIP configuration, use the show running-config command in EXEC mode or the show config command in ROUTER RIP mode. DellEMC(conf-router_rip)#show config ! router rip network 10.0.0.0 DellEMC(conf-router_rip)# When the RIP process has learned the RIP routes, use the show ip rip database command in EXEC mode to view those routes.
PAGE 726
29.0.0.0/8 31.0.0.0/8 [120/1] via 31.0.0.0/8 192.162.2.0/24 [120/1] via 192.162.2.0/24 192.161.1.0/24 [120/1] via 192.161.1.0/24 192.162.3.0/24 [120/1] via 192.162.3.0/24 auto-summary 29.10.10.12, 00:00:26, Fa 1/49 auto-summary 29.10.10.12, 00:01:21, Fa 1/49 auto-summary 29.10.10.12, 00:00:27, Fa 1/49 auto-summary 29.10.10.12, 00:01:22, Fa 1/49 auto-summary To disable RIP globally, use the no router rip command in CONFIGURATION mode.
PAGE 727
To view the current RIP configuration, use the show running-config command in EXEC mode or the show config command in ROUTER RIP mode. Adding RIP Routes from Other Instances In addition to filtering routes, you can add routes from other routing instances or protocols to the RIP process. With the redistribute command, you can include open shortest path first (OSPF), static, or directly connected routes in the RIP process. To add routes from other routing instances or protocols, use the following commands.
PAGE 728
Sending updates every 30 seconds, next due in 23 Invalid after 180 seconds, hold down 180, flushed after 240 Output delay 8 milliseconds between packets Automatic network summarization is in effect Outgoing filter for all interfaces is Incoming filter for all interfaces is Default redistribution metric is 1 Default version control: receive version 2, send version 2 Interface Recv Send TenGigabitEthernet 1/1 2 2 Routing for Networks: 10.0.0.
PAGE 729
To confirm that the default route configuration is completed, use the show config command in ROUTER RIP mode. Summarize Routes Routes in the RIPv2 routing table are summarized by default, thus reducing the size of the routing table and improving routing efficiency in large networks. By default, the autosummary command in ROUTER RIP mode is enabled and summarizes RIP routes up to the classful network boundary. If you must perform routing between discontiguous subnets, disable automatic summarization.
PAGE 730
EXEC privilege mode Enable debugging of RIP. The following example shows the confirmation when you enable the debug function. DellEMC#debug ip rip RIP protocol debug is ON DellEMC# To disable RIP, use the no debug ip rip command. RIP Configuration Example The examples in this section show the command sequence to configure RIPv2 on the two routers shown in the following illustration — Core 2 and Core 3. The host prompts used in the following example reflect those names.
PAGE 731
● To display Core 2 RIP activity, use the show ip protocols command. The following example shows the show ip rip database command to view the learned RIP routes on Core 2. Core2(conf-router_rip)#end 00:12:24: %RPM0-P:CP %SYS-5-CONFIG_I: Configured from console by console Core2#show ip rip database Total number of routes in RIP database: 7 10.11.30.0/24 [120/1] via 10.11.20.1, 00:00:03, TenGigabitEthernet 2/3 10.300.10.0/24 directly connected,TenGigabitEthernet 2/4 10.200.10.
PAGE 732
10.11.20.0 10.11.10.0 Routing Information Sources: Gateway Distance Last Update 10.11.20.1 120 00:00:12 Distance: (default is 120) Core2# RIP Configuration on Core3 The following example shows how to configure RIPv2 on a host named Core3. Core3(conf)#router rip Core3(conf-router_rip)#version 2 Core3(conf-router_rip)#network 192.168.1.0 Core3(conf-router_rip)#network 192.168.2.0 Core3(conf-router_rip)#network 10.11.30.0 Core3(conf-router_rip)#network 10.11.20.
PAGE 733
Gateway of last resort is not set Destination Gateway Dist/Metric Last Change ----------- ------- --------------------R 10.11.10.0/24 via 10.11.20.2, Te 3/21 120/1 00:01:14 C 10.11.20.0/24 Direct, Te 3/21 0/0 00:01:53 C 10.11.30.0/24 Direct, Te 3/11 0/0 00:06:00 R 10.200.10.0/24 via 10.11.20.2, Te 3/21 120/1 00:01:14 R 10.300.10.0/24 via 10.11.20.2, Te 3/21 120/1 00:01:14 C 192.168.1.0/24 Direct, Te 3/23 0/0 00:06:53 C 192.168.2.
PAGE 734
10.11.10.0 10.11.20.0 The following example shows viewing the RIP configuration on Core 3. ! interface TenGigabitEthernet 3/1 ip address 10.11.30.1/24 no shutdown ! interface TenGigabitEthernet 3/2 ip address 10.11.20.1/24 no shutdown ! interface TenGigabitEthernet 3/4 ip address 192.168.1.1/24 no shutdown ! interface TenGigabitEthernet 3/5 ip address 192.168.2.1/24 no shutdown ! router rip version 2 network 10.11.20.0 network 10.11.30.0 network 192.168.1.0 network 192.168.2.
PAGE 735
42 Remote Monitoring (RMON) RMON is an industry-standard implementation that monitors network traffic by sharing network monitoring information. RMON provides both 32-bit and 64-bit monitoring facility and long-term statistics collection on Dell EMC Networking Ethernet interfaces. RMON operates with the simple network management protocol (SNMP) and monitors all nodes on a local area network (LAN) segment. RMON monitors traffic passing through the router and segment traffic not destined for the router.
PAGE 736
[no] rmon alarm number variable interval {delta | absolute} rising-threshold [value event-number] falling-threshold value event-number [owner string] OR [no] rmon hc-alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] Configure the alarm using the following optional parameters: ○ number: alarm number, an integer from 1 to 65,535, the value must be unique in the RMON Alarm Table.
PAGE 737
In the following example, the configuration creates RMON event number 1, with the description “High ifOutErrors”, and generates a log entry when an alarm triggers the event. The user nms1 owns the row that is created in the event table by this command. This configuration also generates an SNMP trap when the event is triggered using the SNMP community string “eventtrap”.
PAGE 738
The following command example enables an RMON MIB collection history group of statistics with an ID number of 20 and an owner of john, both the sampling interval and the number of buckets use their respective defaults.
PAGE 739
43 Rapid Spanning Tree Protocol (RSTP) The Rapid Spanning Tree Protocol (RSTP) is a Layer 2 protocol — specified by IEEE 802.1w — that is essentially the same as spanning-tree protocol (STP) but provides faster convergence and interoperability with switches configured with STP and multiple spanning tree protocol (MSTP).
PAGE 740
● ● ● ● ● ● Prevent Network Disruptions with BPDU Guard Influencing RSTP Root Selection Configuring Spanning Trees as Hitless Enabling SNMP Traps for Root Elections and Topology Changes Configuring Fast Hellos for Link State Detection Flush MAC Addresses after a Topology Change Important Points to Remember ● RSTP is disabled by default. ● Dell EMC Networking OS supports only one Rapid Spanning Tree (RST) instance.
PAGE 741
To verify that an interface is in Layer 2 mode and enabled, use the show config command from INTERFACE mode. The bold lines indicate that the interface is in Layer 2 mode. Enabling Rapid Spanning Tree Protocol Globally Enable RSTP globally on all participating bridges; it is not enabled by default. When you enable RSTP, all physical and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the RST topology. ● Only one path from any bridge to any other bridge is enabled.
PAGE 742
To view the interfaces participating in RSTP, use the show spanning-tree rstp command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output. DellEMC#show spanning-tree rstp Root Identifier has priority 32768, Address 0001.e801.cbb4 Root Bridge hello time 2, max age 20, forward delay 15, max hops 0 Bridge Identifier has priority 32768, Address 0001.e801.
PAGE 743
Te 3/4 R3# Altr 128.684 128 20000 BLK 20000 P2P No Adding and Removing Interfaces To add and remove interfaces, use the following commands. To add an interface to the Rapid Spanning Tree topology, configure it for Layer 2 and it is automatically added. If you previously disabled RSTP on the interface using the command no spanning-tree 0 command, re-enable it using the spanningtree 0 command. ● Remove an interface from the Rapid Spanning Tree topology.
PAGE 744
PROTOCOL SPANNING TREE RSTP mode hello-time seconds NOTE: With large configurations (especially those configurations with more ports) Dell EMC Networking recommends increasing the hello-time. The range is from 1 to 10. The default is 2 seconds. ● Change the max-age parameter. PROTOCOL SPANNING TREE RSTP mode max-age seconds The range is from 6 to 40. The default is 20 seconds. To view the current values for global parameters, use the show spanning-tree rstp command from EXEC privilege mode.
PAGE 745
Influencing RSTP Root Selection RSTP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it is selected as the root bridge. To change the bridge priority, use the following command. ● Assign a number as the bridge priority or designate it as the primary or secondary root. PROTOCOL SPANNING TREE RSTP mode bridge-priority priority-value ○ priority-value The range is from 0 to 65535.
PAGE 746
In the following example, the bold line indicates that the interface is in EdgePort mode. DellEMC(conf-if-te-2/1)#show config ! interface TenGigabitEthernet 2/1 no ip address switchport spanning-tree rstp edge-port shutdown DellEMC(conf-if-te-2/1)# Configuring Fast Hellos for Link State Detection Use RSTP fast hellos to achieve sub-second link-down detection so that convergence is triggered faster. The standard RSTP link-state detection mechanism does not offer the same low link-state detection speed.
PAGE 747
44 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
PAGE 748
45 Security This chapter describes several ways to provide security to the Dell EMC Networking system. For details about all the commands described in this chapter, refer to the Security chapter in the Dell EMC Networking OS Command Reference Guide.
PAGE 749
● Enable AAA accounting and create a record for monitoring the accounting function. CONFIGURATION mode aaa accounting {commands level | dot1x | exec | rest | suppress | system} {default | name} {start-stop | wait-start | stop-only} {radius | tacacs+} The variables are: ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ system: sends accounting information of any other AAA configuration. exec: sends accounting information when a user has logged in to EXEC mode.
PAGE 750
CONFIG-LINE-VTY mode accounting commands 15 com15 accounting exec execAcct DellEMC(config-line-vty)# accounting commands 15 com15 DellEMC(config-line-vty)# accounting exec execAcct Monitoring AAA Accounting Dell EMC Networking OS does not support periodic interim accounting because the periodic command can cause heavy congestion when many users are logged in to the network. No specific show command exists for TACACS+ accounting.
PAGE 751
Sample dot1x accounting records The following lists the sample EAP and MAB accounting records EAP START accounting record: Fri May 10 12:20:43 2019 NAS-IP-Address = 10.16.133.
PAGE 752
NAS-Port = 1010 NAS-Port-Id = "GigabitEthernet 1/11" Service-Type = Call-Check Acct-Session-Time = 21 Acct-Session-Id = "00-11-22-33-44-55-4" Acct-Multi-Session-Id = "00-11-22-33-44-55-00-11-33-44-77-88-5e-50-d6-5cc" Acct-Link-Count = 1 Acct-Terminate-Cause = Lost-Carrier Acct-Status-Type = Stop Event-Timestamp = "May 10 2019 23:30:42 CDT" Tmp-String-9 = "ai:" Acct-Unique-Session-Id = "5a761462ef63b815707de5fa1c5ef348" Timestamp = 1557549042 RADIUS Accounting attributes The following tables describe the va
PAGE 753
Table 85. RADIUS Accounting Stop Record Attributes for CLI user (continued) RADIUS Attribute code RADIUS Attribute Description 46 Acct-Session Time Time the user has received the service. 49 Acct-Terminate-Cause Reason for session termination. 61 NAS-Port-Type ASYNC - for Console session. VIRTUAL - for telnet/SSH session. Table 86.
PAGE 754
Table 88. RADIUS Accounting Stop Record Attributes for dot1x supplicant (continued) RADIUS Attribute code RADIUS Attribute Description 4 NAS-IP-Address IPv4 address of the NAS. 95 NAS-IPv6–Address IPv6 address of the NAS. Session Identification Attributes 1 User-Name User name/ Supplicant MAC Address (for MAB). 5 NAS-Port Port on which session is terminated. 6 Service-Type Framed (2) for EAP /Call check (10) for MAB. 8 Framed-IP-Address IPv4 address of supplicant.
PAGE 755
Table 89. Use cases for dot1x supplicant to trigger RADIUS Accounting Start/Stop records (continued) dot1x event Accounting type Attributes Configure Port control to force unauth Stop Stop record attributes with termination cause as port-reinitialized (21). Interface Host mode change (single/multihost/multiauth) Stop Stop record attributes with termination cause as port-reinitialized (21).
PAGE 756
Configure Login Authentication for Terminal Lines You can assign up to five authentication methods to a method list. Dell EMC Networking OS evaluates the methods in the order in which you enter them in each list. If the first method list does not respond or returns an error, Dell EMC Networking OS applies the next method list until the user either passes or fails the authentication. If the user fails a method list, Dell EMC Networking OS does not apply the next method list.
PAGE 757
○ method1 [... method4]: any of the following: RADIUS, TACACS, enable, line, none. If you do not set the default list, only the local enable is checked. This setting has the same effect as issuing an aaa authentication enable default enable command. Enabling AAA Authentication — RADIUS To enable authentication from the RADIUS server, and use TACACS as a backup, use the following commands. 1. Enable RADIUS and set up TACACS as backup. CONFIGURATION mode aaa authentication enable default radius tacacs 2.
PAGE 758
The re-authentication is also applicable for authenticated 802.1x devices. When there is a change in the authetication servers, the supplicants connected to all the ports are forced to re-authenticate. 1. Enable the re-authentication mode. CONFIGURATION mode aaa reauthentication enable 2. You are prompted to force the users to re-authenticate while adding or removing a RADIUS/TACACS+ server.
PAGE 759
Privilege Levels Overview Limiting access to the system is one method of protecting the system and your network. However, at times, you might need to allow others access to the router and you can limit that access to a subset of commands. In Dell EMC Networking OS, you can configure a privilege level for users who need limited access to the system. Every command in Dell EMC Networking OS is assigned a privilege level of 0, 1, or 15. You can configure up to 16 privilege levels in Dell EMC Networking OS.
PAGE 760
○ privilege level The range is from 0 to 15. ○ Secret:Specify the secret for the user To view username, use the show users command in EXEC Privilege mode. Configuring the Enable Password Command To configure Dell EMC Networking OS, use the enable command to enter EXEC Privilege level 15. After entering the command, Dell EMC Networking OS requests that you enter a password. Privilege levels are not assigned to passwords, rather passwords are assigned to a privilege level.
PAGE 761
enable password [level level] [encryption-mode] password Configure the optional and required parameters: ● level level: specify a level from 0 to 15. Level 15 includes all levels. ● encryption-type: enter 0 for plain text or 7 for encrypted text. ● password: enter a string up to 32 characters long. To change only the password for the enable command, configure only the password parameter. 3. Configure level and commands for a mode or reset a command’s level.
PAGE 762
exit Exit from the EXEC no Negate a command show Show running system information terminal Set terminal line parameters traceroute Trace route to destination DellEMC#confi DellEMC(conf)#? end Exit from Configuration mode exit Exit from Configuration mode no Reset a command snmp-server Modify SNMP parameters DellEMC(conf)# Specifying LINE Mode Password and Privilege You can specify a password authentication of all users on different terminal lines.
PAGE 763
RADIUS Remote authentication dial-in user service (RADIUS) is a distributed client/server protocol. This protocol transmits authentication, authorization, and configuration information between a central RADIUS server and a RADIUS client (the Dell EMC Networking system). The system sends user information to the RADIUS server and requests authentication of the user and password. The RADIUS server returns one of the following responses: ● Access-Accept — the RADIUS server authenticates the user.
PAGE 764
Auto-Command You can configure the system through the RADIUS server to automatically execute a command when you connect to a specific line. The auto-command command is executed when the user is authenticated and before the prompt appears to the user. ● Automatically execute a command. auto-command Privilege Levels Through the RADIUS server, you can configure a privilege level for the user to enter into when they connect to a session. This value is configured on the client system. ● Set a privilege level.
PAGE 765
Applying the Method List to Terminal Lines To enable RADIUS AAA login authentication for a method list, apply it to a terminal line. To configure a terminal line for RADIUS authentication and authorization, use the following commands. ● Enter LINE mode. CONFIGURATION mode line {aux 0 | console 0 | vty number [end-number]} ● Enable AAA login authentication for the specified RADIUS method list.
PAGE 766
CONFIGURATION mode radius-server deadtime seconds ○ seconds: the range is from 0 to 2147483647. The default is 0 seconds. ● Configure a key for all RADIUS communications between the system and RADIUS server hosts. CONFIGURATION mode radius-server key [encryption-type] key ○ encryption-type: enter 7 to encrypt the password. Enter 0 to keep the password as plain text. ○ key: enter a string. The key can be up to 42 characters long. You cannot use spaces in the key.
PAGE 767
aaa authentication login default radius local 2. Specify the protocol for authentication. CONFIGURATION mode aaa radius auth-method mschapv2 3. Establish a host address and password. CONFIGURATION mode radius-server host H key K 4. Log in to switch using console or telnet or ssh with a valid user role. When 1-factor authentication is used, the authentication succeeds enabling you to access the switch.
PAGE 768
disconnect-user operations using DMs, if all NAS identification attributes match, and more than one session matches all of the session identification attributes, then a CoA-request or a disconnect-message request applies to all matching sessions. The following tables describe the various types of attributes that identify the NAS and the user sessions: Table 90. NAS Identification Attributes Attribute code Attribute Description 4 NAS-IP-Address IPv4 address of the NAS.
PAGE 769
Table 95. CoA EAP/MAB Session(s) Re-authenticate (continued) Radius Attribute code Radius Attribute Description Mandatory 4 NAS-IP-Address IPv4 address of the NAS. No 95 NAS-IPv6–Address IPv6 address of the NAS. No Session Identification Attributes 5 NAS-Port Port on which session is terminated Yes, If Calling-Station-Id attribute is not provided 31 Calling-Station-Id The link address from which session is connected.
PAGE 770
Table 98. DM EAP/MAB Session(s) disconnect (continued) Radius Attribute code Radius Attribute Description Mandatory 95 NAS-IPv6–Address IPv6 address of the NAS. No Session Identification Attributes 5 NAS-Port Port on which session is terminated Yes, if Calling-Station-Id attribute is not provided 31 Calling-Station-Id The link address from which session is connected.
PAGE 771
Table 100. Error-cause Values (continued) Serial Number Error-cause Scenarios 3 NAS Identification Mismatch(403) ● CoA request containing NAS-IP-Address or NAS-IPV6-Address that does not match NAS. 4 Administratively Prohibited(501) ● NAS is configured to ignore the CoA or DM request. Also, dot1x is not configured on the NAS-Port. 5 Session Context Not Found(503) ● CoA or DM request containing session identification attributes that does not match any of the NAS user sessions.
PAGE 772
○ Disconnect-Request (40) ○ CoA-Request (43) ● discards the duplicate packets, if NAS is currently processing the original packet. NAS identifies the duplicate packet with the following fields: ○ Source IP address ○ Source UDP port ○ Identifier ○ VRF ID ● discards the packets, if length of the packet is shorter than the length field value. ● discards the packets, if length of the packet is shorter than 20 or longer than 4096.
PAGE 773
client host-name Dell(conf-dynamic-auth#)client testhost Configuring the port number You can configure the port number on which the NAS receives CoA or DM requests. This setting enables you to specify an optional port number on which to receive CoA or DM requests. The default value is 3799. Enter the following command to configure the port number: port port-number The range for the port number value that you can specify is from 1 to 65535.
PAGE 774
Configuring CoA to bounce 802.1x enabled ports Dell EMC Networking OS provides RADIUS extension commands that enables you to configure port bounce settings for the 802.1x enabled port. Before configuring port bounce settings on a 802.1x enabled port, ensure that the following prerequisites are satisfied: ● Shared key is configured in NAS for DAC. ● NAS server listens on the Management IP UDP port 3799 (default) or the port configured through CLI. ● The user is logged-in through 802.
PAGE 775
● sends a CoA-Nak with an error-cause of 402 (missing attribute), if the CoA request does not contain both the callingstation-id as well as the NAS-port attribute. ● sends a CoA-Ack if the re-authentication of the 802.1x session is successful. ● sends a CoA-Nak with an error-cause value of 506 (resource unavailable), if it is unable to initiate the re-authentication process. ● sends a CoA-Nak if user authentication fails due to unresponsive supplicant or RADIUS server.
PAGE 776
1. Enter the following command to configure the dynamic authorization feature: radius dynamic-auth 2. Enter the following command to disable the 802.1x enabled physical port: coa-disable-port NAS administratively shuts down the 802.1x enabled port that is hosting the session. You can re-enable this port only through a non-RADIUS mechanism or through bounce-port request.
PAGE 777
NAS considers the new replay protection window value from next window period. The range is from 1 to 10 minutes. The default is 5 minutes. Dell(conf-dynamic-auth#)replay-prot-window 10 Rate-limiting RADIUS packets NAS enables you to allow or reject RADIUS dynamic authorization packets based on the rate-limiting value that you specify. NAS lets you to configure number of RADIUS dynamic authorization packets allowed per minute. The default value is 30 packets per minute.
PAGE 778
CONFIGURATION mode tacacs-server host {ip-address | host} Enter the IP address or host name of the TACACS+ server. Use this command multiple times to configure multiple TACACS+ server hosts. 2. Enter a text string (up to 16 characters long) as the name of the method list you wish to use with the TACAS+ authentication method. CONFIGURATION mode aaa authentication login {method-list-name | default} tacacs+ [...method3] The TACACS+ method must not be the last method specified. 3. Enter LINE mode.
PAGE 779
Monitoring TACACS+ To view information on TACACS+ transactions, use the following command. ● View TACACS+ transactions to troubleshoot problems. EXEC Privilege mode debug tacacs+ TACACS+ Remote Authentication The system takes the access class from the TACACS+ server. Access class is the class of service that restricts Telnet access and packet sizes.
PAGE 780
Password: DellEMC# Command Authorization The AAA command authorization feature configures Dell EMC Networking OS to send each configuration command to a TACACS server for authorization before it is added to the running configuration. By default, the AAA authorization commands configure the system to check both EXEC mode and CONFIGURATION mode commands. Use the no aaa authorization config-commands command to enable only EXEC mode command checking.
PAGE 781
The following example uses the ip ssh server version 2 command to enable SSH version 2 and the show ip ssh command to confirm the setting. DellEMC(conf)#ip ssh server version 2 DellEMC(conf)#do show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmacsha2-256,hmac-sha2-256-96.
PAGE 782
● show ip ssh client-pub-keys : display the client public keys used in host-based authentication. ● show ip ssh rsa-authentication : display the authorized-keys for the RSA authentication. DellEMC#copy scp: flash: Address or name of remote host []: 10.10.10.1 Port number of the server [22]: 99 Source file name []: test.
PAGE 783
● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 When FIPS is enabled, the default is diffie-hellman-group14-sha1. Example of Configuring a Key Exchange Algorithm The following example shows you how to configure a key exchange algorithm.
PAGE 784
● hmac-sha1-96 ● hmac-sha2-256 The default list of HMAC algorithm is in the following order: ● hmac-sha2-256 ● hmac-sha1 ● hmac-sha1-96 ● hmac-md5 ● hmac-md5-96 When FIPS is enabled, the default HMAC algorithm is hmac-sha2-256, hmac-sha1, hmac-sha1-96. Example of Configuring a HMAC Algorithm The following example shows you how to configure a HMAC algorithm list.
PAGE 785
● aes256-cbc ● aes128-ctr ● aes192-ctr ● aes256-ctr The default cipher list is in the given order: aes256-ctr, aes256-cbc, aes192-ctr, aes192-cbc, aes128-ctr, aes128-cbc, 3des-cbc. Example of Configuring a Cipher List The following example shows you how to configure a cipher list. DellEMC(conf)#ip ssh cipher aes128-ctr aes128-cbc 3des-cbc Configuring DNS in the SSH Server Dell EMC Networking provides support to enable the DNS in SSH server configuration for host-based authentication.
PAGE 786
SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmacsha2-256,hmac-sha2-256-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffie-hellman-group1sha1,diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP Using RSA Authentication of SSH The following procedure authenticates an SSH client based on an RSA key using RSA authentication. This method uses SSH version 2. 1.
PAGE 787
no ip ssh password-authentication or no ip ssh rsa-authentication 6. Enable host-based authentication. CONFIGURATION mode ip ssh hostbased-authentication enable 7. Bind shosts and rhosts to host-based authentication. CONFIGURATION mode ip ssh pub-key-file flash://filename or ip ssh rhostsfile flash://filename The following example shows creating shosts. admin@Unix_client# cd /etc/ssh admin@Unix_client# ls moduli sshd_config ssh_host_dsa_key.pub ssh_host_key.pub ssh_host_rsa_key.
PAGE 788
Enable host-based authentication on the server (Dell EMC Networking system) and the client (Unix machine). The following message appears if you attempt to log in via SSH and host-based is disabled on the client. In this case, verify that host-based authentication is set to “Yes” in the file ssh_config (root permission is required to edit this file): permission denied (host based). If the IP address in the RSA key does not match the IP address from which you attempt to log in, the following message appears.
PAGE 789
can assign different access classes to different users by username. Until users attempt to log in, does not know if they will be assigned a VTY line. This means that incoming users always see a login prompt even if you have excluded them from the VTY line with a deny-all access class. After users identify themselves, retrieves the access class from the local database and applies it. ( then can close the connection if a user is denied access.
PAGE 790
DellEMC(config-line-vty)#access-class sourcemac DellEMC(config-line-vty)#end Role-Based Access Control With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role. Users are granted permissions based on their user roles, not on their individual user ID. User roles are created for job functions and through those roles they acquire the permissions to perform their associated job function.
PAGE 791
NOTE: When you enter a user role, you have already been authenticated and authorized. You do not need to enter an enable password because you will be automatically placed in EXEC Priv mode. For greater security, the ability to view event, audit, and security system log is associated with user roles. For information about these topics, see Audit and Security Logs.
PAGE 792
login authentication test authorization exec test To enable role-based only AAA authorization, enter the following command in Configuration mode: DellEMC(conf)#aaa authorization role-only System-Defined RBAC User Roles By default, the Dell EMC Networking OS provides 4 system defined user roles. You can create up to 8 additional user roles. NOTE: You cannot delete any system defined roles.
PAGE 793
modify command permissions. The security administrator and roles inherited by security administrator can only modify permissions for commands they already have access to. ● Make sure you select the correct role you want to inherit. ● If you inherit a user role, you cannot modify or delete the inheritance. If you want to change or remove the inheritance, delete the user role and create it again. If the user role is in use, you cannot delete the user role. 1.
PAGE 794
The following example denies the netadmin role from using the show users command and then verifies that netadmin cannot access the show users command in exec mode. Note that the netadmin role is not listed in the Role access: secadmin,sysadmin, which means the netadmin cannot access the show users command.
PAGE 795
By default, the system defined role, secadmin, is not allowed to configure protocols. The following example first grants the secadmin role to configure protocols and then removes access to configure protocols. DellEMC(conf)#role configure addrole secadmin protocol DellEMC(conf)#role configure deleterole secadmin protocol Example: Resets Only the Security Administrator role to its original setting. The following example resets only the secadmin role to its original setting.
PAGE 796
that have only privilege levels are denied access to the system because they do not have a role. For information about role only mode, see Configuring Role-based Only AAA Authorization. NOTE: Authentication services only validate the user ID and password combination. To determine which commands are permitted for users, configure authorization. For information about how to configure authorization for roles, see Configure AAA Authorization for Roles.
PAGE 797
line vty 2 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 3 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 4 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 5 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 6 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 7 login
PAGE 798
In the following example, you create an AV pair for a user-defined role. You must also define a role, using the userrole myrole inherit command on the switch to associate it with this AV pair. Force10-avpair= ”shell:role=myrole“ The string, “myrole”, is associated with a TACACS+ user group. The user IDs are associated with the user group. Role Accounting This section describes how to configure role accounting and how to display active sessions for roles.
PAGE 799
Display Information About User Roles This section describes how to display information about user roles and consists of the following topics: ● Displaying User Roles ● Displaying Information About Roles Logged into the Switch ● Displaying Active Accounting Sessions for Roles Displaying User Roles To display user roles using the show userrole command in EXEC Privilege mode, use the show userroles and show users commands in EXEC privilege mode.
PAGE 800
*3 vty 1 4 vty 2 sec1 ml1 secadmin netadmin 14 12 idle idle 172.31.1.4 172.31.1.5 Two Factor Authentication (2FA) Two factor authentication also known as 2FA, strengthens the login security by providing one time password (OTP) in addition to username and password. 2FA supports RADIUS authentications with Console, Telnet, and SSHv2. To perform 2FA, follow these steps: ● When the Network access server (NAS) prompts for the username and password, provide the inputs.
PAGE 801
Challenge Response Auth : enabled. Vty Encryption 2 aes128-cbc 4 aes128-cbc * 5 aes128-cbc DellEMC# HMAC hmac-md5 hmac-md5 hmac-md5 Remote IP 10.16.127.141 10.16.127.141 10.16.127.141 SMS-OTP Mechanism A short message service one time password (SMS-OTP) is a free RADIUS module to implement two factor authentication. There are multiple 2FA mechanisms that can be deployed with the RADIUS.
PAGE 802
Table 102. Suppressed ICMP message types (continued) ICMPv4 message types Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMP message type echo request (8). Table 103.
PAGE 803
Dell EMC Networking OS Security Hardening The security of a network consists of multiple factors. Apart from access to the device, best practices, and implementing various security features, security also lies with the integrity of the device. If the software itself is compromised, all of the aforementioned methods become ineffective. The Dell EMC Networking OS is enhanced verify whether the OS image and the startup configuration file are altered before loading.
PAGE 804
● Use the following command to upgrade the Dell EMC Networking OS and enter the hash value when prompted. EXEC Privilege upgrade system DellEMC# upgrade system tftp://10.16.127.35/FTOS-SE-9.11.0.1 A: Hash Value: e42e2548783c2d5db239ea2fa9de4232 !!!!!!!!!!!!!!... Startup Configuration Verification Dell EMC Networking OS comes with startup configuration verification feature.
PAGE 805
After enabling and configuring startup configuration verification, the device verifies the hash checksum of the startup configuration during every reload. DellEMC# verified boot hash startup—config 619A8C1B7A2BC9692A221E2151B9DA9E Configuring the root User Password For added security, you can change the root user password. If you configure the secure-cli command on the system, the Dell EMC Networking OS resets any previously-configured root access password without displaying any warning message.
PAGE 806
46 Service Provider Bridging Service provider bridging provides the ability to add a second VLAN ID tag in an Ethernet frame and is referred to as VLAN stacking in the Dell EMC Networking OS. Topics: • • • • • VLAN Stacking VLAN Stacking Packet Drop Precedence Dynamic Mode CoS for VLAN Stacking Layer 2 Protocol Tunneling Provider Backbone Bridging VLAN Stacking VLAN stacking, also called Q-in-Q, is defined in IEEE 802.1ad — Provider Bridges, which is an amendment to IEEE 802.
PAGE 807
Figure 115. VLAN Stacking in a Service Provider Network Important Points to Remember ● Interfaces that are members of the Default VLAN and are configured as VLAN-Stack access or trunk ports do not switch untagged traffic. To switch traffic, add these interfaces to a non-default VLAN-Stack-enabled VLAN. ● Dell EMC Networking cautions against using the same MAC address on different customer VLANs, on the same VLAN-Stack VLAN.
PAGE 808
Related Configuration Tasks ● ● ● ● Configuring the Protocol Type Value for the Outer VLAN Tag Configuring Dell EMC Networking OS Options for Trunk Ports Debugging VLAN Stacking VLAN Stacking in Multi-Vendor Networks Creating Access and Trunk Ports To create access and trunk ports, use the following commands. ● Access port — a port on the service provider edge that directly connects to the customer. An access port may belong to only one service provider VLAN.
PAGE 809
NOTE: When the VRF feature is enabled, you cannot configure a VLAN interface as a vlan-stack. DellEMC#show vlan Codes: * - Default VLAN, G - GVRP VLANs NUM * 1 2 3 4 5 6 Status Active Inactive Inactive Inactive Inactive Active DellEMC# Q Ports U Te 3/0-5,18 M Po1(Te 3/14-15) M Te 3/13 Configuring the Protocol Type Value for the Outer VLAN Tag The tag protocol identifier (TPID) field of the S-Tag is user-configurable. To set the S-Tag TPID, use the following command. ● Select a value for the S-Tag TPID.
PAGE 810
DellEMC(conf-if-vl-101)#tagged tengigabitethernet 1/1 DellEMC(conf-if-vl-101)#interface vlan 103 DellEMC(conf-if-vl-103)#vlan-stack compatible DellEMC(conf-if-vl-103-stack)#member tengigabitethernet 1/1 DellEMC(conf-if-vl-103-stack)#do show vlan Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM * 1 100 101 103 Status Inactive Inactive Inactive Inactive Description Q Ports U Te 1/1 T Te 1/1 M Te 1/1 Debugging VLAN St
PAGE 811
You can configure the first 8 bits of the TPID using the vlan-stack protocol-type command. The TPID is global. Ingress frames that do not match the system TPID are treated as untagged. This rule applies for both the outer tag TPID of a double-tagged frame and the TPID of a single-tagged frame. For example, if you configure TPID 0x9100, the system treats 0x8100 and untagged traffic the same and maps both types to the default VLAN, as shown by the frame originating from Building C.
PAGE 812
Figure 117.
PAGE 813
Figure 118. Single and Double-Tag TPID Mismatch VLAN Stacking Packet Drop Precedence VLAN stacking packet-drop precedence is supported on the switch. The drop eligible indicator (DEI) bit in the S-Tag indicates to a service provider bridge which packets it should prefer to drop when congested. Enabling Drop Eligibility Enable drop eligibility globally before you can honor or mark the DEI value. When you enable drop eligibility, DEI mapping or marking takes place according to the defaults.
PAGE 814
Table 104. Drop Eligibility Behavior (continued) Ingress Egress DEI Disabled DEI Enabled Trunk Port Trunk Port Retain inner tag CFI Retain inner tag CFI. Retain outer tag CFI Set outer tag CFI to 0. Retain inner tag CFI Retain inner tag CFI Set outer tag CFI to 0 Set outer tag CFI to 0 Access Port Trunk Port To enable drop eligibility globally, use the following command. ● Make packets eligible for dropping based on their DEI value.
PAGE 815
To display the DEI-marking configuration, use the show interface dei-mark [interface slot/port ] in EXEC Privilege mode. DellEMC#show interface dei-mark Default CFI/DEI Marking: 0 Interface Drop precedence CFI/DEI -------------------------------Te 1/1 Green 0 Te 1/1 Yellow 1 Te 2/9 Yellow 0 Te 2/10 Yellow 0 Dynamic Mode CoS for VLAN Stacking One of the ways to ensure quality of service for customer VLAN-tagged frames is to use the 802.1p priority bits in the tag to indicate the level of QoS desired.
PAGE 816
Examples of QoS Interface Configuration and Rate Policing policy-map-input in layer2 service-queue 3 class-map a qos-policy 3 ! class-map match-any a layer2 match mac access-group a ! mac access-list standard a seq 5 permit any ! qos-policy-input 3 layer2 rate-police 40 Likewise, in the following configuration, packets with dot1p priority 0–3 are marked as dot1p 7 in the outer tag and queued to Queue 3. Rate policing is according to qos-policy-input 3.
PAGE 817
NOTE: Because dot1p-mapping marks and queues packets, the only remaining applicable QoS configuration is rate metering. You may use Rate Shaping or Rate Policing. Layer 2 Protocol Tunneling Spanning tree bridge protocol data units (BPDUs) use a reserved destination MAC address called the bridge group address, which is 01-80-C2-00-00-00. Only spanning-tree bridges on the local area network (LAN) recognize this address and process the BPDU.
PAGE 818
Dell EMC Networking OS Behavior: In Dell EMC Networking OS versions prior to 8.2.1.0, the MAC address that Dell EMC Networking systems use to overwrite the Bridge Group Address on ingress was non-configurable. The value of the L2PT MAC address was the Dell EMC Networking-unique MAC address, 01-01-e8-00-00-00.
PAGE 819
EXEC Privilege mode show cam-profile 2. Enable protocol tunneling globally on the system. CONFIGURATION mode protocol-tunnel enable 3. Tunnel BPDUs the VLAN. INTERFACE VLAN mode protocol-tunnel stp Specifying a Destination MAC Address for BPDUs By default, Dell EMC Networking OS uses a Dell EMC Networking-unique MAC address for tunneling BPDUs. You can configure another value. To specify a destination MAC address for BPDUs, use the following command.
PAGE 820
Provider Backbone Bridging IEEE 802.1ad—Provider Bridges amends 802.1Q—Virtual Bridged Local Area Networks so that service providers can use 802.1Q architecture to offer separate VLANs to customers with no coordination between customers, and minimal coordination between customers and the provider. 802.
PAGE 821
47 sFlow sFlow is a standard-based sampling technology embedded within switches and routers which is used to monitor network traffic. It is designed to provide traffic monitoring for high-speed networks with many switches and routers.
PAGE 822
● If the global sampling rate is non-default, for example 256, and if the sampling rate is not configured on the interface, the sampling rate of the interface is the global non-default sampling rate, that is, 256. To avoid the back-off, either increase the global sampling rate or configure all the line card ports with the desired sampling rate even if some ports have no sFlow configured.
PAGE 823
Te 1/1: configured rate 16384, actual rate 16384 DellEMC# If you did not enable any extended information, the show output displays the following (shown in bold).
PAGE 824
Example of the show sflow command when the sflow max-header-size extended is configured globally DellEMC(conf-if-te-1/10)#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 86400 Global default extended maximum header size: 256 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.12, Agent IP addr: 100.1.1.
PAGE 825
Global default sampling rate: 32768 Global default counter polling interval: 20 1 collectors configured Collector IP addr: 133.33.33.53, Agent IP addr: 133.33.33.
PAGE 826
Configuring Specify Collectors The sflow collector command allows identification of sFlow collectors to which sFlow datagrams are forwarded. You can specify up to two sFlow collectors. If you specify two collectors, the samples are sent to both. ● Identify sFlow collectors to which sFlow datagrams are forwarded. CONFIGURATION mode sflow collector ip-address agent-addr ip-address [number [max-datagram-size number] ] | [max-datagram-size number ] The default UDP port is 6343.
PAGE 827
● extended-switch — 802.1Q VLAN ID and 802.1p priority information. ● extended-router — Next-hop and source and destination mask length. ● extended-gateway — Source and destination AS number and the BGP next-hop. NOTE: The entire AS path is not included. BGP community-list and local preference information are not included. These fields are assigned default values and are not interpreted by the collector. ● Enable extended sFlow.
PAGE 828
Table 105. Extended Gateway Summary (continued) IP SA IP DA srcAS and srcPeerAS dstAS and dstPeerAS Description there is no AS information. static/connected/IGP BGP 0 Exported src_as and src_peer_as are zero because there is no AS information for IGP. BGP static/connected/IGP — — Exported Exported Prior to Dell EMC Networking OS version 7.8.1.0, extended gateway data is not exported because IP DA is not learned via BGP. Version 7.8.1.
PAGE 829
48 Simple Network Management Protocol (SNMP) The Simple Network Management Protocol (SNMP) is designed to manage devices on IP networks by monitoring device operation, which might require administrator intervention. NOTE: On Dell EMC Networking routers, standard and private SNMP management information bases (MIBs) are supported, including all Get and a limited number of Set operations (such as set vlan and copy cmd).
PAGE 830
• • • Troubleshooting SNMP Operation Transceiver Monitoring Configuring SNMP context name Protocol Overview Network management stations use SNMP to retrieve or alter management data from network elements. A datum of management information is called a managed object; the value of a managed object can be static or variable. Network elements store managed objects in a database called a management information base (MIB).
PAGE 831
In this example, for a specified user and a group, the AES128-CFB algorithm, the authentication password to enable the server to receive packets from the host, and the privacy password to encode the message contents are configured. SHA authentication needs to be used with the AES-CFB128 privacy algorithm only when FIPS is enabled because SHA is then the only available authentication level.
PAGE 832
Set up SNMP As previously stated, Dell EMC Networking OS supports SNMP version 1 and version 2 that are community-based security models. The primary difference between the two versions is that version 2 supports two additional protocol operations (informs operation and snmpgetbulk query) and one additional object (counter64 object). SNMP version 3 (SNMPv3) is a user-based security model that provides password authentication for user security and encryption for data security and privacy.
PAGE 833
snmp-server group group-name 3 noauth auth read name write name ● Configure an SNMPv3 view. CONFIGURATION mode snmp-server view view-name oid-tree {included | excluded} NOTE: To give a user read and write view privileges, repeat this step for each privilege type. ● Configure the user with an authorization password (password privileges only). CONFIGURATION mode snmp-server user name group-name 3 noauth auth md5 auth-password ● Configure an SNMP group (password privileges only).
PAGE 834
Reading Managed Object Values You may only retrieve (read) managed object values if your management station is a member of the same community as the SNMP agent. Dell EMC Networking supports RFC 4001, Textual Conventions for Internet Work Addresses that defines values representing a type of internet address. These values display for ipAddressTable objects using the snmpwalk command. There are several UNIX SNMP commands that read data. ● Read the value of a single managed object.
PAGE 835
Configuring Contact and Location Information using SNMP You may configure system contact and location information from the Dell EMC Networking system or from the management station using SNMP. To configure system contact and location information from the Dell EMC Networking system and from the management station using SNMP, use the following commands.
PAGE 836
To send informational messages, enter the keyword informs. To send the SNMP version to use for notification messages, enter the keyword version. To identify the SNMPv1 community string, enter the name of the community-string. 2. Specify which traps the Dell EMC Networking system sends to the trap receiver. CONFIGURATION mode snmp-server enable traps Enable all Dell EMC Networking enterprise-specific and RFC-defined traps using the snmp-server enable traps command from CONFIGURATION mode.
PAGE 837
ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CPU_THRESHOLD: Cpu %s usage above threshold. Cpu5SecUsage (%d) CPU_THRESHOLD_CLR: Cpu %s usage drops below threshold. Cpu5SecUsage (%d) MEM_THRESHOLD: Memory %s usage above threshold. MemUsage (%d) MEM_THRESHOLD_CLR: Memory %s usage drops below threshold. MemUsage (%d) DETECT_STN_MOVE: Station Move threshold exceeded for Mac %s in vlan %d CAM-UTILIZATION: Enable SNMP envmon CAM utilization traps.
PAGE 838
4:08:15.68,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1, SNMPv2-SMI::enterprises.6027.3.6.1.1.2.
PAGE 839
10.11.226.121 (port: 9140) is reachable"SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 2 Following is the sample audit log message that other syslog servers that are reachable receive: Oct 21 05:26:04: dv-fedgov-s4810-6: %EVL-6-REACHABLE:Syslog server 10.11.226.121 (port: 9140) is reachable Copy Configuration Files Using SNMP To do the following, use SNMP from a remote client.
PAGE 840
Table 108. MIB Objects for Copying Configuration Files via SNMP (continued) MIB Object OID Object Values Description ● If copyDestFileType is a binary, you must specify copyDestFileLocation and copyDestFileName. copyDestFileLocation .1.3.6.1.4.1.6027.3.5.1.1.1.1.6 1 = flash 2 = slot0 3 = tftp 4 = ftp 5 = scp Specifies the location of destination file. ● If copyDestFileLocation is FTP or SCP, you must specify copyServerAddress, copyUserName, and copyUserPassword. copyDestFileName .1.3.6.1.4.1.6027.
PAGE 841
● index must be unique to all previously executed snmpset commands. If an index value has been used previously, a message like the following appears. In this case, increment the index value and enter the command again. Error in packet. Reason: notWritable (that object does not support modification) Failed object: FTOS-COPY-CONFIG-MIB::copySrcFileType.101 ● To complete the command, use as many MIB objects in the command as required by the MIB object descriptions shown in the previous table.
PAGE 842
The following example shows how to copy configuration files from a UNIX machine using the object name. > snmpset -c public -v 2c -m ./f10-copy-config.mib 10.11.131.162 copySrcFileType.7 i 3 copyDestFileType.7 i 2 FTOS-COPY-CONFIG-MIB::copySrcFileType.7 = INTEGER: runningConfig(3) FTOS-COPY-CONFIG-MIB::copyDestFileType.7 = INTEGER: startupConfig(2) The following example shows how to copy configuration files from a UNIX machine using OID. >snmpset -c public -v 2c 10.11.131.162 .1.3.6.1.4.1.6027.3.5.1.1.1.1.2.
PAGE 843
Copy a Binary File to the Startup-Configuration To copy a binary file from the server to the startup-configuration on the Dell EMC Networking system via FTP, use the following command. ● Copy a binary file from the server to the startup-configuration on the Dell EMC Networking system via FTP. snmpset -v 2c -c public -m ./f10-copy-config.mib force10system-ip-address copySrcFileType.index i 1 copySrcFileLocation.index i 4 copySrcFileName.index s filepath/ filename copyDestFileType.index i 3 copyServerAddress.
PAGE 844
index: the index value used in the snmpset command used to complete the copy operation. NOTE: You can use the entire OID rather than the object name. Use the form: OID.index. The following examples show the snmpget command to obtain a MIB object value. These examples assume that: ● ● ● ● the server OS is UNIX you are using SNMP version 2c the community name is public the file f10-copy-config.mib is in the current directory NOTE: In UNIX, enter the snmpset command for help using this command.
PAGE 845
MIB Support for Power Monitoring Dell EMC Networking provides MIB objects to display the information for Power Monitoring. The OIDs specific to Power Monitoring are appended to the DellITaMIbs. There are three separate DellITaMIbs available to display the current input power, average input power and average input-power start time. These statistics can also be obtained by using the CLI command: show environment . The following table lists the related MIB objects, OID and description for the same: Table 111.
PAGE 846
Table 112. MIB Objects to Display support for 25G, 40G, 50G, 100G Optical Transceiver or DAC cable IDPROM user info (continued) MIB Object OID Description dellNetIfTransSerialNumber 1.3.6.1.4.1.6027.3.11.1.3.1.1.7 Specifies the Serial Number of the Optic inserted dellNetIfTransTransmitPowerLane1 1.3.6.1.4.1.6027.3.11.1.3.1.1.8 Specifies Lane 1 Tx power value in dBm dellNetIfTransTransmitPowerLane2 1.3.6.1.4.1.6027.3.11.1.3.1.1.
PAGE 847
MIB Support to Display the Available Memory Size on Flash Dell EMC Networking provides more MIB objects to display the available memory size on flash memory. The following table lists the MIB object that contains the available memory size on flash memory. Table 113. MIB Objects for Displaying the Available Memory Size on Flash via SNMP MIB Object OID Description chStackUnitFlashUsageUtil 1.3.6.1.4.1.6027.3.10.1.2.9.1.6 Contains flash memory usage in percentage.
PAGE 848
Viewing the Software Core Files Generated by the System ● To view the software core files generated by the system, use the following command. snmpwalk -v2c -c public 192.168.60.120 .1.3.6.1.4.1.6027.3.10.1.2.10 enterprises.6027.3.10.1.2.10.1.1.1.1 = 1 enterprises.6027.3.10.1.2.10.1.1.1.2 = 2 enterprises.6027.3.10.1.2.10.1.1.1.3 = 3 enterprises.6027.3.10.1.2.10.1.1.2.1 = 1 enterprises.6027.3.10.1.2.10.1.2.1.1 = "/CORE_DUMP_DIR/flashmntr.core.gz" enterprises.6027.3.10.1.2.10.1.2.1.
PAGE 849
Viewing the CAM MIB ● To view the CAM MIB generated by the system, use the following commands. snmpwalk -c public -v 2c 10.16.210.24 1.3.6.1.4.1.6027.3.7.1.1.3.1.12 SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.12.1.1.1 = INTEGER: 0 snmpwalk -c public -v 2c 10.16.210.24 1.3.6.1.4.1.6027.3.7.1.1.3.1.16 SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.16.1.1.1 = INTEGER: 1 snmpwalk -c public -v 2c 10.16.210.24 1.3.6.1.4.1.6027.3.7.1.1.3.1.18 SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.18.1.1.
PAGE 850
Table 116. MIB Objects to Display the Information for PFC Storm Control (continued) MIB Object OID Description dellNetFpPfcStormControlDiscardStateF 1.3.6.1.4.1.6027.3.27.1.21.2.1.1.2 orcedClearCount Number of times the queue is moved forcefully to normal state. dellNetFpPfcStormControlDiscardStateN 1.3.6.1.4.1.6027.3.27.1.21.2.1.1.3 orxPfcClearCount Number of times the queue is moved to normal state due to no rxPFC. SNMP Walk Example Output snmpwalk -v 2c -c public 10.16.134.200 1.3.6.1.4.1.6027.3.
PAGE 851
SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.2.2097669.5 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.2.2097669.6 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.2.2097925.5 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.2.2097925.6 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.3.2097157.5 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.3.2097157.6 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.3.2097413.5 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.3.2097413.6 SNMPv2-SMI::enterprises.6027.3.27.1.21.2.1.1.3.2097669.
PAGE 852
Table 118. MIB Objects to Display the Information for Monitoring the overall buffer usage for lossy and lossless traffic per XPE. (continued) MIB Object OID Description dellNetFpServicePoolBufferSizeEntry 1.3.6.1.4.1.6027.3.27.1.23.1 Table to show the sizes of configured and used lossy as well as lossless service pools. dellNetFpXPENumber 1.3.6.1.4.1.6027.3.27.1.23.1.1 Denotes XPE number in the MMU. dellNetFpLossyServicePoolConfiguredBu 1.3.6.1.4.1.6027.3.27.1.23.1.
PAGE 853
SNMPv2-SMI::enterprises.6027.3.27.1.3.1.5.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.6.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.7.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.8.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.9.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.10.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.11.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.12.
PAGE 854
snmpwalk -v 2c -c public -On 10.16.150.97 1.3.6.1.4.1.6027.3.26.1.4.8 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.4 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.4 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.4 .1.3.6.1.4.1.6027.3.
PAGE 855
Table 121. MIB Objects to display egress queue statistics (continued) MIB Object OID Description dellNetFpEgrQDroppedPacketsRate 1.3.6.1.4.1.6027.3.27.1.20.1.8 Rate of Packets dropped per Unicast/ Multicast Egress queue. dellNetFpEgrQDroppedBytesRate 1.3.6.1.4.1.6027.3.27.1.20.1.9 Rate of Bytes dropped per Unicast/ Multicast Egress queue. MIB Support to ECMP Group Count Dell EMC Networking OS provides MIB objects to display the information of the ECMP group count information.
PAGE 856
INTEGER: 1258296320 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.80.80.80.0.24.1.4.30.1.1.1.1.4.30.1.1.1 = INTEGER: 1275078656 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.90.90.90.0.24.0.0.0.0 = INTEGER: 2097157 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.90.90.90.1.32.1.4.127.0.0.1.1.4.127.0.0.1 = INTEGER: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.90.90.90.2.32.1.4.90.90.90.2.1.4.90.90.90.2 = INTEGER: 2097157 SNMPv2SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.100.100.100.0.24.1.4.10.1.1.1.1.4.10.1.
PAGE 857
SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.20.1.1.1.32.1.4.20.1.1.1.1.4.20.1.1.1 = STRING: "Po 10" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.20.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.0.24.0.0.0.0 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.1.32.1.4.30.1.1.1.1.4.30.1.1.1 = STRING: "Po 20" SNMPv2SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.
PAGE 858
Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.80.80.80.0.24.1.4.30.1.1.1.1.4.30.1.1.1 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.90.90.90.0.24.0.0.0.0 = Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.90.90.90.1.32.1.4.127.0.0.1.1.4.127.0.0.1 = Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.90.90.90.2.32.1.4.90.90.90.2.1.4.90.90.90.2 = Gauge32: 0 SNMPv2SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.100.100.100.0.24.1.4.10.1.1.1.1.4.10.1.1.
PAGE 859
.1.3.6.1.2.1.47.1.3.2.1.2.30.0 = OID: .1.3.6.1.2.1.2.2.1.1.2100356 .1.3.6.1.2.1.47.1.3.2.1.2.31.0 = OID: .1.3.6.1.2.1.2.2.1.1.2100484 MIB Support to Display the FCS Error Ratio Details Dell EMC Networking provides MIB objects to display the FCS Error Ratio details. Table 124. MIB Objects for Displaying the Details of FCS Error Ratio MIB Object OID Description dellNetFpDropsTable 1.3.6.1.4.1.6027.3.27.1.
PAGE 860
Table 124. MIB Objects for Displaying the Details of FCS Error Ratio (continued) MIB Object OID Description dellNetFpEgHgMacUnderFlow 1.3.6.1.4.1.6027.3.27.1.3.1.21 Hg MacUnderflow. dellNetFpEgTxErrPktCounter 1.3.6.1.4.1.6027.3.27.1.3.1.22 TX Error Packet Counter. dellNetFpFlowControlDrops 1.3.6.1.4.1.6027.3.27.1.3.1.23 Flow Control Drops. dellNetFpIngressDropsBytes 1.3.6.1.4.1.6027.3.27.1.3.1.24 Ingress Drops Byte Counter. dellNetFpIngressFECBitErrors 1.3.6.1.4.1.6027.3.27.1.3.1.
PAGE 861
SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1059845 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1060357 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1060869 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1061381 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1061893 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1062404 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1062532 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1062660 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.1062788 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.28.
PAGE 862
Table 125. MIB Objects for LAG (continued) MIB Object OID Description dot3adAggPartnerSystemID 1.2.840.10006.300.43.1.1.1.1.7 Contains a six octet read–only MAC address value consisting of an unique identifier for the current Protocol partner of the Aggregator. dot3adAggPartnerSystemPriority 1.2.840.10006.300.43.1.1.1.1.8 Contains a two octet read–only value that indicates the priority value associated with the Partner’s system ID. dot3adAggPartnerOperKey 1.2.840.10006.300.43.1.1.1.1.
PAGE 863
MIB Support to Display Unrecognized LLDP TLVs This section provides information about MIB objects that display unrecognized LLDP TLV information about reserved and organizational specific unrecognized LLDP TLVs. MIB Support to Display Reserved Unrecognized LLDP TLVs The lldpRemUnknownTLVTable contains the information about an incoming reserved unrecognized LLDP TLVs that is not recognized by the local neighbor. The following table lists the related MIB objects: Table 126.
PAGE 864
MIB Support to Display Organizational Specific Unrecognized LLDP TLVs The lldpRemOrgDefInfoTable contains organizationally defined information that is not recognized by the local neighbor. The following table lists the related MIB objects: Table 127. MIB Objects for Displaying Organizational Specific Unrecognized LLDP TLVs MIB Object OID Description lldpRemOrgDefInfoTable 1.0.8802.1.1.2.1.4.4 This table contains organizationally defined information that is not recognized by the local neighbor.
PAGE 865
Global MIB objects for port security This section describes about the scalar MIB objects of the global MIB dellNetPortSecGlobalObjects. The following table shows the scalar global MIB objects for port security. Table 128. Global MIB Objects for Port Security MIB Object OID Access or Permission Description dellNetGlobalPortSecurityMod 1.3.6.1.4.1.6027.3.31.1.1.1 e read-write Enables or disables port security feature globally on the device. dellNetGlobalTotalSecureAddr 1.3.6.1.4.1.6027.3.31.1.1.
PAGE 866
Table 129. Interface level MIB Objects for Port Security (continued) MIB Object OID Access or Permission Description dellNetPortSecIfStickyEnable 1.3.6.1.4.1.6027.3.31.1.2.1.1.8 read-write Enables or disables sticky port security feature on this interface. dellNetPortSecIfClearSecure MacAddresses 1.3.6.1.4.1.6027.3.31.1.2.1.1.9 read-write Deletes secure MAC addresses based on the specified type. dellNetPortSecIfResetViolatio nStatus 1.3.6.1.4.1.6027.3.31.1.2.1.1.
PAGE 867
Table 130. MIB Objects for configuring MAC addresses MIB Object OID Access or Permission Description dellNetPortSecSecureStaticM acAddrTable. Enabling and viewing SNMP for static MAC addresses You can enable and view SNMP for static MAC addresses using snmpset and snmpget command. Following example shows how to enable and view the static MAC addresses. To configure a static MAC address (00:00:00:00:11:11) on a vlan (100) on interface whose ifIndex is (2101252), use the following command.
PAGE 868
MIB support for MAC notification traps Dell EMC Networking OS provides MIB support to generate SNMP trap messages on learning or station move of a new or existing MAC address in the system with mac–address, vlan–id, and port details. The following table lists the related MIB objects, OID, and description for the same: Table 132. MIB Objects for MAC notification traps MIB Object OID Description dellNetMacNotifMib 1.3.6.1.4.1.6027.3.28.1 Contains the MAC notification groups.
PAGE 869
Manage VLANs using SNMP The qBridgeMIB managed objects in Q-BRIDGE-MIB, defined in RFC 2674, allows you to use SNMP to manage VLANs. Creating a VLAN To create a VLAN, use the dot1qVlanStaticRowStatus object. The snmpset operation shown in the following example creates VLAN 10 by specifying a value of 4 for instance 10 of the dot1qVlanStaticRowStatus object. > snmpset -v2c -c mycommunity 123.45.6.78 .1.3.6.1.2.1.17.7.1.4.3.1.5.10 i 4 SNMPv2-SMI::mib-2.17.7.1.4.3.1.5.
PAGE 870
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00" .1.3.6.1.2.1.17.7.1.4.3.1.4.1107787786 x "40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00" SNMPv2-SMI::mib-2.17.7.1.4.3.1.2.
PAGE 871
respectively To set time to wait till bgp session are up set 1.3.6.1.4.1.6027.3.18.1.3 and 1.3.6.1.4.1.6027.3.18.1.6 Enabling and Disabling a Port using SNMP To enable and disable a port using SNMP, use the following commands. 1. Create an SNMP community on the Dell system. CONFIGURATION mode snmp-server community 2. From the Dell EMC Networking system, identify the interface index of the port for which you want to change the admin status.
PAGE 872
example, the decimal equivalent of E8 is 232, and so the instance number for MAC address 00:01:e8:06:95:ac is.0.1.232.6.149.172. The value of dot1dTpFdbPort is the port number of the port off which the system learns the MAC address. In this case, of TenGigabitEthernet 1/21, the manager returns the integer 118.
PAGE 873
MIB Objects for Viewing the System Image on Flash Partitions To view the system image on Flash Partition A, use the chSysSwInPartitionAImgVers object or, to view the system image on Flash Partition B, use the chSysSwInPartitionBImgVers object. Table 134. MIB Objects for Viewing the System Image on Flash Partitions MIB Object OID Description MIB chSysSwInPartitionAImgVers 1.3.6.1.4.1.6027.3.10.1.2.8.1.11 List the version string of the system image in Flash Partition A.
PAGE 874
● snmp-server community VRF2 ro ● snmp-server context cx1 ● snmp-server context cx2 ● snmp-server group admingroup 3 auth read readview write writeview ● snmp-server group admingroup 3 auth read readview context cx1 ● snmp-server group admingroup 3 auth read readview context cx2 ● snmp-server user admin admingroup 3 auth md5 helloworld ● snmp mib community-map VRF1 context cx1 ● snmp mib community-map VRF2 context cx2 ● snmp-server view readview .1 included ● snmp-server view writeview .1 included 2.
PAGE 875
Monitor Port-Channels To check the status of a Layer 2 port-channel, use f10LinkAggMib (.1.3.6.1.4.1.6027.3.2). In the following example, Po 1 is a switchport and Po 2 is in Layer 3 mode. Example of SNMP Trap for Monitored Port-Channels [senthilnathan@lithium ~]$ snmpwalk -v 2c -c public 10.11.1.1 .1.3.6.1.4.1.6027.3.2.1.1 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.1 = INTEGER: 1 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.2 = INTEGER: 2 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.
PAGE 876
IF-MIB::linkUp IF-MIB::ifIndex.1107755009 = INTEGER: 1107755009 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_UP: Changed interface state to up: Po 1" Troubleshooting SNMP Operation When you use SNMP to retrieve management data from an SNMP agent on a Dell EMC Networking router, take into account the following behavior. ● When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the snmpwalk command, the output for echo replies may be incorrectly displayed.
PAGE 877
Table 135. SNMP OIDs for Transceiver Monitoring (continued) Field (OID) Description SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.4 Optics Type SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.5 Vendor Name SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.6 Part Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.7 Serial Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.8 Transmit Power Lane1 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.9 Transmit Power Lane2 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.
PAGE 878
49 Stacking Using the Dell EMC Networking OS stacking feature, you can interconnect multiple switch units with stacking ports or front end user ports. The stack becomes manageable as a single switch through the stack management unit. The system accepts Unit ID numbers from 0 to 6 and the S6000 supports stacking up to six units with Dell EMC Networking OS version 9.7(0.0).
PAGE 879
Stack Master Election The stack elects a master and standby unit at bootup time based on two criteria. ● Unit priority — User-configurable. The range is from 1 to 14. A higher value (14) means a higher priority. The default is 0. By removing the stack-unit priority using the no stack-unit priority command, you can set the priority back to the default value of zero. The unit with the highest priority is elected the master management unit; the unit with the second highest priority is elected the standby unit.
PAGE 880
Virtual IP You can manage the stack using a single IP, known as a virtual IP, that is retained in the stack even after a failover. The virtual IP address is used to log in to the current master unit of the stack. Both IPv4 and IPv6 addresses are supported as virtual IPs. Use the following command to configure a virtual IP: Dell(conf)#virtual-ip {ip-address | ipv6–address | dhcp} Failover Roles If the stack master fails (for example, is powered off), it is removed from the stack topology.
PAGE 881
2 Member not present 3 Member not present 4 Member not present 5 Member not present 6 Member not present 7 Member not present [output omitted] Stack#show system stack-unit 0 | grep priority Master priority : 0 Stack#show system stack-unit 1 | grep priority Master priority : 0 Example of Adding a Standalone with a Lower MAC Address and Equal Priority to a Stack ---------------STANDALONE AFTER CONNECTION----------------Standalone#%STKUNIT0-M:CP %POLLMGR-2-ALT_STACK_UNIT_STATE: Alternate Stack-unit is present
PAGE 882
Figure 122. Supported Stacking Topologies High Availability on Stacks Stacks have master and standby management units analogous to Dell EMC Networking route processor modules (RPM). The master unit synchronizes the running configuration and protocol states so that the system fails over in the event of a hardware or software fault on the master unit. In such an event, or when the master unit is removed, the standby unit becomes the stack manager and Dell EMC Networking OS elects a new standby unit.
PAGE 883
exit format fsck pwd rename reset show ssh-peer-stack-unit start telnet-peer-stack-unit terminal upload Dell(standby)# Exit from the EXEC Format a filesystem Filesystem check utility Display current working directory Rename a file Reset selected card Show running system information Open a SSH connection to the peer stack-unit Start shell Open a telnet connection to the peer stack-unit Set terminal line parameters Upload file -----------------CONSOLE ACCESS ON A MEMBER---------------------------Dell(stack-
PAGE 884
Figure 123. Stack-Group Assignments You can connect the units while they are powered down or up. Stacking ports are bidirectional. When a unit is added to a stack, the management unit performs a system check on the new unit to ensure the hardware type is compatible. A similar check is performed on the Dell EMC Networking OS version. If the stack is running Dell EMC Networking OS version9.7.0.0and the new unit is running an earlier software version, the new unit is put into a card problem state.
PAGE 885
3. Reload the switch. EXEC Privilege mode reload Dell EMC Networking OS automatically assigns a number to the new unit and adds it as member switch in the stack. The new unit synchronizes its running and startup configurations with the stack. 4. After the units are reloaded, the system reboots. The units come up in a stack after the reboot completes. To view the port assignments, use the show system stack-unit command.
PAGE 886
Figure 124. Creating a new stack In the above example, stack unit 1 is the master management unit, stack unit 2 is the standby unit. The cables are connected to each unit.
PAGE 887
Stack MAC Reload-Type : 90:b1:1c:f4:a7:c7 : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Member not present S6000 1 Member not present 2 Standby online S6000 S6000 1-0(0-3387) 128 3 Member not present S6000 4 Member not present 5 Management online S6000 S6000 1-0(0-3387) 128 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ------------------------
PAGE 888
CONFIGURATION mode stack-unit stack-unit-number priority priority-number 4. Assign a stack group to each unit. CONFIGURATION mode stack-unitstack-unit-number stack-group stack-group-number 5. Connect the new unit to the stack using stacking cables. The following example shows adding a stack unit with a conflicting stack number (before).
PAGE 889
● stack-group group-number: configures a port for stacking. 6. Save the stacking configuration on the ports. EXEC Privilege mode write memory 7. Reload the switch. EXEC Privilege mode reload Dell EMC Networking OS automatically assigns a number to the new unit and adds it as member switch in the stack. The new unit synchronizes its running and startup configurations with the stack. 8. If a standalone switch already has stack groups configured.
PAGE 890
● ● ● ● ● Displaying Information About a Stack Influencing Management Unit Selection on a Stack Managing Redundancy on a Stack Resetting a Unit on a Stack Recover from Stack Link Flaps Assigning Unit Numbers to Units in an Stack Each unit in the stack has a stack number that is either assigned by you or Dell EMC Networking OS. Stack numbers are stored in NVRAM and are preserved upon reload. ● Assign a stack-number to a unit.
PAGE 891
Unit Type : Standby Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 1 Hardware Rev : 4.
PAGE 892
Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Member not present S6000 1 Member not present 2 Standby online S6000 S6000 1-0(0-3387) 128 3 Member not present S6000 4 Member not present 5 Management online S6000 S6000 1-0(0-3387) 128 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------2 0 up AC up 6720 2 1 up AC up 6688 5 0 up AC up 6688
PAGE 893
Managing Redundancy on a Stack Use the following commands to manage the redundancy on a stack. ● Reset the current management unit and make the standby unit the new master unit. EXEC Privilege mode redundancy force-failover stack-unit A new standby is elected. When the former stack master comes back online, it becomes a member unit. ● Prevent the stack master from rebooting after a failover.
PAGE 894
(Gb/s) Status Status Group ----------------------------------------------------1/48 7/56 42 up up 1/52 5/60 42 up up 2/56 6/52 42 up up 2/60 4/52 42 up up 3/48 7/52 42 up up 3/52 5/56 42 up up 4/52 6/48 42 up up 4/56 4/48 42 up up DellEMC# The following example shows the parameters for the management unit in the stack.
PAGE 895
5/4 5/120 DellEMC# 2/4 42 42 up up down up Remove Units or Front End Ports from a Stack To remove units or front end ports from a stack, use the following instructions. ● Removing a Unit from a Stack ● Removing Front End Port Stacking Removing a Unit from a Stack The running-configuration and startup-configuration are synchronized on all stack units. A stack member that is disconnected from the stack maintains this configuration.
PAGE 896
CONFIGURATION mode no stack-unit id stack-group id 2. Save the stacking configuration on the ports. EXEC Privilege mode write memory 3. Reload the switch. EXEC Privilege mode reload After the units are reloaded, the system reboots. The units come up as standalone units after the reboot completes. Troubleshoot a Stack To troubleshoot a stack, use the following recovery tasks.
PAGE 897
Stack MAC Reload-Type : 90:b1:1c:f4:a7:c7 : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Member not present S6000 unknown 128 1 Member not present 2 Standby online S6000 S6000 1-0(0-3387) 128 3 Member not present S6000 4 Member not present 5 Management online S6000 S6000 1-0(0-3387) 128 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ------------
PAGE 898
50 Storm Control Storm control allows you to control unknown-unicast, muticast, and broadcast traffic on Layer 2 and Layer 3 physical interfaces. Dell EMC Networking Operating System (OS) Behavior: Dell EMC Networking OS supports unknown-unicast, muticast, and broadcast control for Layer 2 and Layer 3 traffic. To view the storm control broadcast configuration show storm-control broadcast | multicast | unknownunicast | pfc-llfc[interface] command.
PAGE 899
● Configure the packets per second of multicast traffic allowed on C-Series or S-Series interface (ingress only) network only. INTERFACE mode storm-control multicast packets_per_second in ● Shut down the port if it receives the PFC/LLFC packets more than the configured rate. INTERFACE mode storm-control pfc-llfc pps in shutdown NOTE: PFC/LLFC storm control enabled interface disables the interfaces if it receives continuous PFC/LLFC packets.
PAGE 900
Detect PFC Storm The following section explains the procedure to detect the PFC storm. You can detect the PFC storm by polling the lossless queues in a port or priority periodically. When the queue depth is not equal to zero or when the queue has traffic after subsequent number of polling, then the port or priority is detected to have the PFC storm. ● Use the polling—interval {interval in milli-seconds} command to set the polling interval. The queue traffic and egress counters are polled.
PAGE 901
Te 0/0 Te 0/1 Te 0/2 Te 0/3 Te 0/4 Te 0/5 Te 0/80 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 2 2 2 2 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DellEMC# Storm Control 901
PAGE 902
51 Spanning Tree Protocol (STP) The spanning tree protocol (STP) is supported on Dell EMC Networking OS.
PAGE 903
● ● ● ● ● ● ● Modifying Global Parameters Modifying Interface STP Parameters Enabling PortFast Prevent Network Disruptions with BPDU Guard STP Root Guard Enabling SNMP Traps for Root Elections and Topology Changes Configuring Spanning Trees as Hitless Important Points to Remember ● STP is disabled by default. ● The Dell EMC Networking OS supports only one spanning tree instance (0). For multiple instances, enable the multiple spanning tree protocol (MSTP) or per-VLAN spanning tree plus (PVST+).
PAGE 904
Configuring Interfaces for Layer 2 Mode All interfaces on all switches that participate in spanning tree must be in Layer 2 mode and enabled. Figure 125. Example of Configuring Interfaces for Layer 2 Mode To configure and enable the interfaces for Layer 2, use the following command. 1. If the interface has been assigned an IP address, remove it. INTERFACE mode no ip address 2. Place the interface in Layer 2 mode. INTERFACE switchport 3. Enable the interface.
PAGE 905
no shutdown DellEMC(conf-if-te-1/1)# Enabling Spanning Tree Protocol Globally Enable the spanning tree protocol globally; it is not enabled by default. When you enable STP, all physical, VLAN, and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the Spanning Tree topology. ● Only one path from any bridge to any other bridge participating in STP is enabled. ● Bridges block a redundant path by disabling one of the link ports. Figure 126.
PAGE 906
To view the spanning tree configuration and the interfaces that are participating in STP, use the show spanning-tree 0 command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output. R2#show spanning-tree 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, address 0001.e826.ddb7 Configured hello time 2, max age 20, forward delay 15 Current root has priority 32768, address 0001.e80d.
PAGE 907
Modifying Global Parameters You can modify the spanning tree parameters. The root bridge sets the values for forward-delay, hello-time, and max-age and overwrites the values set on other bridges participating in STP. NOTE: Dell EMC Networking recommends that only experienced network administrators change the spanning tree parameters. Poorly planned modification of the spanning tree parameters can negatively affect network performance. The following table displays the default values for STP. Table 137.
PAGE 908
Modifying Interface STP Parameters You can set the port cost and port priority values of interfaces in Layer 2 mode. ● Port cost — a value that is based on the interface type. The greater the port cost, the less likely the port is selected to be a forwarding port. ● Port priority — influences the likelihood that a port is selected to be a forwarding port in case that several ports have the same port cost. The default values are listed in Modifying Global Parameters.
PAGE 909
Prevent Network Disruptions with BPDU Guard Configure the Portfast (and Edgeport, in the case of RSTP, PVST+, and MSTP) feature on ports that connect to end stations. End stations do not generate BPDUs, so ports configured with Portfast/ Edgport (edgeports) do not expect to receive BDPUs. If an edgeport does receive a BPDU, it likely means that it is connected to another part of the network, which can negatively affect the STP topology.
PAGE 910
Figure 127. Enabling BPDU Guard Dell EMC Networking OS Behavior BPDU guard: ● is used on edgeports and blocks all traffic on edgeport if it receives a BPDU. ● drops the BPDU after it reaches the RP and generates a console message. Example of Blocked BPDUs DellEMC(conf-if-te-1/7)#do show spanning-tree rstp brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e805.fb07 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e85d.
PAGE 911
Selecting STP Root The STP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it becomes the root bridge. You can also specify that a bridge is the root or the secondary root. To change the bridge priority or specify that a bridge is the root or secondary root, use the following command. ● Assign a number as the bridge priority or designate it as the root or secondary root.
PAGE 912
Figure 128. STP Root Guard Prevents Bridging Loops Configuring Root Guard Enable STP root guard on a per-port or per-port-channel basis. Dell EMC Networking OS Behavior: The following conditions apply to a port enabled with STP root guard: ● Root guard is supported on any STP-enabled port or port-channel interface except when used as a stacking port.
PAGE 913
To disable STP root guard on a port or port-channel interface, use the no spanning-tree 0 rootguard command in an interface configuration mode. To verify the STP root guard configuration on a port or port-channel interface, use the show spanning-tree 0 guard [interface interface] command in a global configuration mode. Enabling SNMP Traps for Root Elections and Topology Changes To enable SNMP traps individually or collectively, use the following commands.
PAGE 914
As soon as a BPDU is received on an STP port in a Loop-Inconsistent state, the port returns to a blocking state. If you disable STP loop guard on a port in a Loop-Inconsistent state, the port transitions to an STP blocking state and restarts the max-age timer. Figure 129. STP Loop Guard Prevents Forwarding Loops Configuring Loop Guard Enable STP loop guard on a per-port or per-port channel basis.
PAGE 915
○ If a BPDU is received from a remote device, BPDU guard places the port in an Err-Disabled Blocking state and no traffic is forwarded on the port. ○ If no BPDU is received from a remote device, loop guard places the port in a Loop-Inconsistent Blocking state and no traffic is forwarded on the port. ● When used in a PVST+ network, STP loop guard is performed per-port or per-port channel at a VLAN level.
PAGE 916
52 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide. Figure 130.
PAGE 917
Enable the SupportAssist service. CONFIGURATION mode support-assist activate DellEMC(conf)#support-assist activate This command guides you through steps to configure SupportAssist. Configuring SupportAssist Manually To manually configure SupportAssist service, use the following commands. 1. Accept the end-user license agreement (EULA). CONFIGURATION mode eula-consent {support-assist} {accept | reject} NOTE: Once accepted, you do not have to accept the EULA again.
PAGE 918
CONFIGURATION mode support-assist DellEMC(conf)#support-assist DellEMC(conf-supportassist)# 3. (Optional) Configure the contact information for the company. SUPPORTASSIST mode contact-company name {company-name}[company-next-name] ... [company-next-name] DellEMC(conf)#support-assist DellEMC(conf-supportassist)#contact-company name test DellEMC(conf-supportassist-cmpy-test)# 4. (Optional) Configure the contact name for an individual.
PAGE 919
[no] activity {full-transfer|core-transfer|event-transfer} DellEMC(conf-supportassist)#activity full-transfer DellEMC(conf-supportassist-act-full-transfer)# DellEMC(conf-supportassist)#activity core-transfer DellEMC(conf-supportassist-act-core-transfer)# DellEMC(conf-supportassist)#activity event-transfer DellEMC(conf-supportassist-act-event-transfer)# 2. Copy an action-manifest file for an activity to the system.
PAGE 920
SUPPORTASSIST ACTIVITY mode [no] enable DellEMC(conf-supportassist-act-full-transfer)#enable DellEMC(conf-supportassist-act-full-transfer)# DellEMC(conf-supportassist-act-core-transfer)#enable DellEMC(conf-supportassist-act-core-transfer)# DellEMC(conf-supportassist-act-event-transfer)#enable DellEMC(conf-supportassist-act-event-transfer)# Configuring SupportAssist Company SupportAssist Company mode allows you to configure name, address and territory information of the company.
PAGE 921
[no] contact-person [first ] last DellEMC(conf-supportassist)#contact-person first john last doe DellEMC(conf-supportassist-pers-john_doe)# 2. Configure the email addresses to reach the contact person. SUPPORTASSIST PERSON mode [no] email-address primary email-address [alternate email-address] DellEMC(conf-supportassist-pers-john_doe)#email-address primary jdoe@mycompany.com DellEMC(conf-supportassist-pers-john_doe)# 3. Configure phone numbers of the contact person.
PAGE 922
[no] enable DellEMC(conf-supportassist-serv-default)#enable DellEMC(conf-supportassist-serv-default)# 4. Configure the URL to reach the SupportAssist remote server. SUPPORTASSIST SERVER mode [no] url uniform-resource-locator DellEMC(conf-supportassist-serv-default)#url https://192.168.1.1/index.htm DellEMC(conf-supportassist-serv-default)# Viewing SupportAssist Configuration To view the SupportAssist configurations, use the following commands: 1.
PAGE 923
! server Dell enable url http://1.1.1.1:1337 DellEMC# 3. Display the EULA for the feature. EXEC Privilege mode show eula-consent {support-assist | other feature} DellEMC#show eula-consent support-assist SupportAssist EULA has been: Accepted Additional information about the SupportAssist EULA is as follows: By installing SupportAssist, you allow Dell to save your contact information (e.g.
PAGE 924
53 System Time and Date System time and date settings and the network time protocol (NTP) are supported on Dell EMC Networking OS. You can set system times and dates and maintained through the NTP. They are also set through the Dell EMC Networking Operating System (OS) command line interfaces (CLIs) and hardware settings. The Dell EMC Networking OS supports reaching an NTP server through different VRFs. You can configure a maximum of eight logging servers across different VRFs or the same VRF.
PAGE 925
Protocol Overview The NTP messages to one or more servers and processes the replies as received. The server interchanges addresses and ports, fills in or overwrites certain fields in the message, recalculates the checksum, and returns it immediately. Information included in the NTP message allows each client/server peer to determine the timekeeping characteristics of its other peers, including the expected accuracies of their clocks.
PAGE 926
To display the system clock state with respect to NTP, use the show ntp status command from EXEC Privilege mode. DellEMC#show ntp status Clock is synchronized, stratum 4, reference is 10.16.151.117, vrf-id is 0 frequency is -44.862 ppm, stability is 0.050 ppm, precision is -18 reference time deeef7ef.85eeaa10 Tue, Jul 10 2018 9:16:31.523 UTC clock offset is -0.167449 msec, root delay is 149.194 msec root dispersion is 54.557 msec, peer dispersion is 0.
PAGE 927
○ ○ ○ ○ ○ ○ For For For For For For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. a Loopback interface, enter the keyword loopback then a number from 0 to 16383. the Management interface, enter the keyword ManagementEthernet then the slot/port information. a port channel interface, enter the keywords port-channel then a number.
PAGE 928
○ minpoll polling-interval: Enter the minpoll value. The range is from 4 to 16. ○ maxpoll polling-interval: Enter the maxpoll value. The range is from 4 to 16. 5. Configure the switch as NTP master. CONFIGURATION mode ntp master To configure the switch as NTP Server use the ntp master command. stratum number identifies the NTP Server's hierarchy. The following example shows configuring an NTP server. Dell EMC(conf)#show running-config ntp ! ntp master ntp server 10.16.127.
PAGE 929
● Originate Timestamp: The departure time on the server of its last NTP message. If the server becomes unreachable, the value is set to zero. ● Receive Timestamp — the arrival time on the client of the last NTP message from the server. If the server becomes unreachable, the value is set to zero. ● Transmit Timestamp — the departure time on the server of the current NTP message from the sender. ● Filter dispersion — the error in calculating the minimum delay from a set of sample data from a peer.
PAGE 930
The range for threshold-value is from 0 to 999. DellEMC(conf)#ntp offset-threshold 9 Dell EMC Networking OS Time and Date You can set the time and date using the Dell EMC Networking OS CLI. Configuration Task List The following is a configuration task list for configuring the time and date settings.
PAGE 931
￭￭ a number from 1 to 23 as the number of hours in addition to UTC for the timezone. a minus sign (-) then a number from 1 to 23 as the number of hours. DellEMC#conf DellEMC(conf)#clock timezone Pacific -8 DellEMC(conf)#01:40:19: %RPM0-P:CP %CLOCK-6-TIME CHANGE: Timezone configuration changed from "UTC 0 hrs 0 mins" to "Pacific -8 hrs 0 mins" DellEMC# Set Daylight Saving Time Dell EMC Networking OS supports setting the system to daylight saving time once or on a recurring basis every year.
PAGE 932
clock summer-time time-zone recurring start-week start-day start-month start-time endweek end-day end-month end-time [offset] ○ time-zone: Enter the three-letter name for the time zone. This name displays in the show clock output. ○ start-week: (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ￭ week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time.
PAGE 933
54 Tunneling Tunnel interfaces create a logical tunnel for IPv4 or IPv6 traffic. Tunneling supports RFC 2003, RFC 2473, and 4213. DSCP, hop-limits, flow label values, open shortest path first (OSPF) v2, and OSPFv3 are supported. Internet control message protocol (ICMP) error relay, PATH MTU transmission, and fragmented packets are not supported.
PAGE 934
tunnel mode ipv6ip no shutdown The following sample configuration shows a tunnel configured in IPIP mode (IPv4 tunnel carries IPv4 and IPv6 traffic): DellEMC(conf)#interface tunnel 3 DellEMC(conf-if-tu-3)#tunnel source 5::5 DellEMC(conf-if-tu-3)#tunnel destination 8::9 DellEMC(conf-if-tu-3)#tunnel mode ipv6 DellEMC(conf-if-tu-3)#ip address 3.1.1.1/24 DellEMC(conf-if-tu-3)#ipv6 address 3::1/64 DellEMC(conf-if-tu-3)#no shutdown DellEMC(conf-if-tu-3)#show config ! interface Tunnel 3 ip address 3.1.1.
PAGE 935
The following sample configuration shows how to use the interface tunnel configuration commands. DellEMC(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 ip address 20.1.1.1/24 ipv6 address 20:1::1/64 no shutdown DellEMC(conf)#interface tunnel 1 DellEMC(conf-if-tu-1)#ip unnumbered tengigabitethernet 1/1 DellEMC(conf-if-tu-1)#ipv6 unnumbered tengigabitethernet 1/1 DellEMC(conf-if-tu-1)#tunnel source 40.1.1.
PAGE 936
DellEMC(conf-if-tu-1)#no shutdown DellEMC(conf-if-tu-1)#show config ! interface Tunnel 1 ip address 1.1.1.1/24 ipv6 address 1abd::1/64 tunnel source anylocal tunnel allow-remote 40.1.1.2 tunnel mode ipip decapsulate-any no shutdown Guidelines for Configuring Multipoint Receive-Only Tunnels ● You can configure up to eight remote end-points for a multipoint receive-only tunnel.
PAGE 937
55 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if used with network interface controller (NIC) teaming, automatic recovery from a failed link.
PAGE 938
Figure 132. Uplink Failure Detection How Uplink Failure Detection Works UFD creates an association between upstream and downstream interfaces. The association of uplink and downlink interfaces is called an uplink-state group. An interface in an uplink-state group can be a physical interface or a port-channel (LAG) aggregation of physical interfaces. An enabled uplink-state group tracks the state of all assigned upstream interfaces.
PAGE 939
Figure 133. Uplink Failure Detection Example If only one of the upstream interfaces in an uplink-state group goes down, a specified number of downstream ports associated with the upstream interface are put into a Link-Down state. You can configure this number and is calculated by the ratio of the upstream port bandwidth to the downstream port bandwidth in the same uplink-state group.
PAGE 940
● If one of the upstream interfaces in an uplink-state group goes down, either a user-configurable set of downstream ports or all the downstream ports in the group are put in an Operationally Down state with an UFD Disabled error. The order in which downstream ports are disabled is from the lowest numbered port to the highest.
PAGE 941
UPLINK-STATE-GROUP mode downstream auto-recover The default is auto-recovery of UFD-disabled downstream ports is enabled. To disable auto-recovery, use the no downstream auto-recover command. 5. (Optional) Enter a text description of the uplink-state group. UPLINK-STATE-GROUP mode description text The maximum length is 80 alphanumeric characters. 6. (Optional) Disable upstream-link tracking without deleting the uplink-state group.
PAGE 942
02:37:29: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Fo 3/60 02:38:31 : UFD: Group:3, UplinkState: UP 02:38:31: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Changed uplink state group state to up: Group 3 02:38:53: Fo 3/48 02:38:53: Fo 3/52 02:38:53: Fo 3/56 02:38:53: Fo 3/60 02:38:53: 02:38:53: 02:38:53: 02:38:53: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cleared from UFD error-disabled: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Downstream interface cleared from UFD error-disabled: %RPM0-P:CP %IFMGR
PAGE 943
Uplink State Group : 1 Upstream Interfaces : Downstream Interfaces : Status: Enabled, Up Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/6(Up) Te 1/7(Up) Downstream Interfaces : Te 3/1(Up) Te 3/3(Up) Te 3/5(Up) Te 3/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 1/1(Dwn) Te 1/3(Dwn) Te 1/5(Dwn) Downstream Interfaces : Te 3/2(Dis) Te 3/4(Dis) Te 3/11(Dis) Te 3/12(Dis) Te 3/13(Dis) Te 3/14(Dis) Te 3/15(Dis) Uplink State Group : 6 Upstream Interfaces : Downs
PAGE 944
downstream TenGigabitEthernet 1/1, 3, 5, 7-10 upstream TengigabitEthernet 1/16, 20 DellEMC(conf-uplink-state-group-16)# show configuration ! uplink-state-group 16 no enable description test downstream disable links all downstream TenGigabitEthernet 1/21 upstream TenGigabitEthernet 1/22 upstream Port-channel 8 Sample Configuration: Uplink Failure Detection The following example shows a sample configuration of UFD on a switch/router in which you configure as follows.
PAGE 945
(Up): Interface up (Dwn): Interface down (Dis): Interface disabled Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/3(Up) Te 1/4(Dwn) Downstream Interfaces : Te 1/1(Dis) Te 1/2(Dwn) Te 1/5(Dwn) Te 1/9(Dwn) Te 1/11(Dwn) Te 1/12(Dwn) Uplink Failure Detection (UFD) 945
PAGE 946
56 Upgrade Procedures To find the upgrade procedures, go to the Dell EMC Networking OS Release Notes for your system type to see all the requirements needed to upgrade to the desired Dell EMC Networking OS version. To upgrade your system type, follow the procedures in the Dell EMC Networking OS Release Notes. You can download the release notes of your platform at https://www.force10networks.com. Use your login ID to log in to the website.
PAGE 947
57 Virtual LANs (VLANs) Virtual LANs (VLANs) are a logical broadcast domain or logical grouping of interfaces in a local area network (LAN) in which all data received is kept locally and broadcast to all members of the group. When in Layer 2 mode, VLANs move traffic at wire speed and can span multiple devices. The system supports up to 4093 portbased VLANs and one default VLAN, as specified in IEEE 802.1Q.
PAGE 948
NOTE: You cannot assign an IP address to the Default VLAN. To assign an IP address to a VLAN that is currently the Default VLAN, create another VLAN and assign it to be the Default VLAN. For more information about assigning IP addresses, refer to Assigning an IP Address to a VLAN. ● Untagged interfaces must be part of a VLAN. To remove an untagged interface from the Default VLAN, create another VLAN and place the interface into that VLAN.
PAGE 949
● The VLAN protocol identifier identifies the frame as tagged according to the IEEE 802.1Q specifications (2 bytes). ● Tag control information (TCI) includes the VLAN ID (2 bytes total). The VLAN ID can have 4,096 values, but two are reserved. NOTE: The insertion of the tag header into the Ethernet frame increases the size of the frame to more than the 1,518 bytes as specified in the IEEE 802.3 standard. Some devices that are not compliant with IEEE 802.3 may not support the larger frame size.
PAGE 950
Assigning Interfaces to a VLAN You can only assign interfaces in Layer 2 mode to a VLAN using the tagged and untagged commands. To place an interface in Layer 2 mode, use the switchport command. You can further designate these Layer 2 interfaces as tagged or untagged. For more information, see the Interfaces chapter and Configuring Layer 2 (Data Link) Mode.
PAGE 951
When you remove a tagged interface from a VLAN (using the no tagged interface command), it remains tagged only if it is a tagged interface in another VLAN. If the tagged interface is removed from the only VLAN to which it belongs, the interface is placed in the Default VLAN as an untagged interface. Moving Untagged Interfaces To move untagged interfaces from the Default VLAN to another VLAN, use the following commands. 1. Access INTERFACE VLAN mode of the VLAN to which you want to assign the interface.
PAGE 952
Assigning an IP Address to a VLAN VLANs are a Layer 2 feature. For two physical interfaces on different VLANs to communicate, you must assign an IP address to the VLANs to route traffic between the two interfaces. The shutdown command in INTERFACE mode does not affect Layer 2 traffic on the interface; the shutdown command only prevents Layer 3 traffic from traversing over the interface. NOTE: You cannot assign an IP address to the Default VLAN (VLAN 1).
PAGE 953
Enabling Null VLAN as the Default VLAN In a Carrier Ethernet for Metro Service environment, service providers who perform frequent reconfigurations for customers with changing requirements occasionally enable multiple interfaces, each connected to a different customer, before the interfaces are fully configured. This presents a vulnerability because both interfaces are initially placed in the native VLAN, VLAN 1, and for that period customers are able to access each other's networks.
PAGE 954
58 Virtual Link Trunking (VLT) Virtual link trunking (VLT) is a Dell EMC technology that provides two Dell EMC switches the ability to function as a single switch. VLT allows physical links between two Dell EMC switches to appear as a single virtual link to the network core or other switches such as Edge, Access, or top-of-rack (ToR). As a result, the two physical switches appear as a single switch to the connected devices.
PAGE 955
VLT not only overcomes this caveat, but also provides a multipath to the connected devices. In the example shown below, the two physical VLT peers appear as a single logical device to the connected devices. As the connected devices consider the VLT peers as a single switch, VLT eliminates STP-blocked ports. However, the two VLT devices are independent Layer2/Layer3 (L2/L3) switches for devices in the upstream network. Figure 136.
PAGE 956
Figure 137. Example of VLT Deployment VLT offers the following benefits: ● ● ● ● ● ● ● ● ● ● ● ● Allows a single device to use a LAG across two upstream devices. Eliminates STP-blocked ports. Provides a loop-free topology. Uses all available uplink bandwidth. Provides fast convergence if either the link or a device fails. Optimized forwarding with virtual router redundancy protocol (VRRP). Provides link-level resiliency. Assures high availability. Active-Active load sharing with VRRP.
PAGE 957
● VLT backup link — The backup link monitors the connectivity between the VLT peer switches. The backup link sends configurable, periodic keep alive messages between the VLT peer switches. ● VLT interconnect (VLTi) — The link used to synchronize states between the VLT peer switches. Both ends must be on 10G or 40G interfaces. ● VLT domain — This domain includes both the VLT peer devices, VLT interconnect, and all of the port channels in the VLT connected to the attached devices.
PAGE 958
Viewing the MAC Synchronization Between VLT Peers You can use the following commands to verify the MAC synchronization between VLT peers: VLT-10-PEER-1#show mac-address-table count MAC Entries for all vlans : Dynamic Address Count : 1007 Static Address (User-defined) Count : 1 Sticky Address Count : 0 Total Synced Mac from Peer(N): 503 Total MAC Addresses in Use: 1008 VLT-10-PEER-1#show vlt counter mac Total MAC VLT counters ---------------------L2 Total MAC-Address Count: 1007 VLT-10-PEER-1#show mac-addr
PAGE 959
that all the uplinks from servers to access and access to aggregation are in Active-Active Load Sharing mode. This example provides the highest form of resiliency, scaling, and load balancing in data center switching networks. The following example shows stacking at the access, VLT in aggregation, and Layer 3 at the core. Figure 139. VLT on Core Switches The aggregation layer is mostly in the L2/L3 switching/routing layer.
PAGE 960
Figure 140. Enhanced VLT Configure Virtual Link Trunking VLT requires that you enable the feature and then configure the same VLT domain, backup link, and VLT interconnect on both peer switches. Important Points to Remember WARNING: Do not add any VLANs to the VLT Interconnect. The VLTi interface manages VLAN tagged/untagged traffic automatically between peers. Manually adding any VLAN configuration has been shown to disrupt traffic flow.
PAGE 961
● ● ● ● ● ● ● ● ● ● ● ● channels to or from a VLAN. You can manually add or remove a VLTi port-channel to a VLAN. In case a VLTi port-channel is manually removed from a VLAN, it is added back to the VLAN after reload of the VLTi peers. Use the lacp ungroup member-independent command only if the system connects to nodes using bare metal provisioning (BMP) to upgrade or boot from the network.
PAGE 962
Configuration Notes When you configure VLT, the following conditions apply. ● With VLT, when an L3 interface is created, the local DA of that interface is added as an L2 entry pointing to the ICL interface on the peer chassis. This ensures that the L3 packets reaching the peer, by LAG hashing on ToR, get forwarded to the actual chassis via ICL and then get routed. When this interface is removed, the entry pointing to ICL on the peer chassis is deleted.
PAGE 963
NOTE: If you configure the VLT system MAC address or VLT unit-id on only one of the VLT peer switches, the link between the VLT peer switches is not established. Each VLT peer switch must be correctly configured to establish the link between the peers. ○ If the link between the VLT peer switches is established, changing the VLT system MAC address or the VLT unit-id causes the link between the VLT peer switches to become disabled.
PAGE 964
○ ○ ○ ○ ○ ○ ○ ￭ Ingress and egress QoS policies applied on VLT ports must be the same on both VLT peers. ￭ Apply the same ingress and egress QoS policies on VLTi (ICL) member ports to handle failed links. For detailed information about how to use VRRP in a VLT domain, see the following VLT and VRRP interoperability section. For information about configuring IGMP Snooping in a VLT domain, see VLT and IGMP Snooping.
PAGE 965
can configure another peer as the Primary Peer using the VLT domain domain-id role priority priority-value command. If the VLTi link fails, the status of the remote VLT Primary Peer is checked using the backup link. If the remote VLT Primary Peer is available, the Secondary Peer disables all VLT ports to prevent loops. If all ports in the VLTi link fail or if the communication between VLTi links fails, VLT checks the backup link to determine the cause of the failure.
PAGE 966
VLT and IGMP Snooping When configuring IGMP Snooping with VLT, ensure the configurations on both sides of the VLT trunk are identical to get the same behavior on both sides of the trunk. When you configure IGMP snooping on a VLT node, the dynamically learned groups and multicast router ports are automatically learned on the VLT peer node. VLT IPv6 The following features have been enhanced to support IPv6: ● VLT Sync — Entries learned on the VLT interface are synced on both VLT peers.
PAGE 967
Figure 141. PIM-Sparse Mode Support on VLT On each VLAN where the VLT peer nodes act as the first hop or last hop routers, one of the VLT peer nodes is elected as the PIM designated router. If you configured IGMP snooping along with PIM on the VLT VLANs, you must configure VLTi as the static multicast router port on both VLT peer switches. This ensures that for first hop routers, the packets from the source are redirected to the designated router (DR) if they are incorrectly hashed.
PAGE 968
If the VLT node elected as the designated router fails and you enable VLT Multicast Routing, multicast routes are synced to the other peer for traffic forwarding to ensure minimal traffic loss. If you did not enable VLT Multicast Routing, traffic loss occurs until the other VLT peer is selected as the DR. VLT Routing VLT Routing refers to the ability to run a dynamic routing protocol within a single VLT domain or between VLT domains (mVLT).
PAGE 969
If you enable peer routing, a VLT node acts as a proxy gateway for its connected VLT peer as shown in the image below. Even though the gateway address of the packet is different, Peer-1 routes the packet to its destination on behalf of Peer-2 to avoid sub-optimal routing. Figure 143. Packets with peer routing enabled Benefits of Peer Routing ● ● Avoids sub-optimal routing ● Reduces latency by avoiding another hop in the traffic path.
PAGE 970
Configuring VLT Unicast To enable and configure VLT unicast, follow these steps. 1. Enable VLT on a switch, then configure a VLT domain and enter VLT-domain configuration mode. CONFIGURATION mode vlt domain domain-id 2. Enable peer-routing. VLT DOMAIN mode peer-routing 3. Configure the peer-routing timeout. VLT DOMAIN mode peer-routing—timeout value value: Specify a value (in seconds) from 1 to 65535. The default value is infinity (without configuring the timeout).
PAGE 971
3. Configure the multicast peer-routing timeout. VLT DOMAIN mode multicast peer-routing—timeout value value: Specify a value (in seconds) from 1 to 1200. NOTE: Reduce the multicast peer-routing-timeout value to 10 seconds to clear the (S,G) entry in mroute in primary VLT peer. Also, the MLD leave packet must be sent after the unicast route convergence. 4. Configure a PIM-SM compatible VLT node as a designated router (DR). For more information, refer to Configuring a Designated Router. 5.
PAGE 972
Sample RSTP configuration The following is a sample of an RSTP configuration: Using the example shown in the Overview section as a sample VLT topology, the primary VLT switch sends BPDUs to an access device (switch or server) with its own RSTP bridge ID. BPDUs generated by an RSTP-enabled access device are only processed by the primary VLT switch. The secondary VLT switch tunnels the BPDUs that it receives to the primary VLT switch over the VLT interconnect.
PAGE 973
Configuring a VLT Interconnect To configure a VLT interconnect, follow these steps. 1. Configure the port channel for the VLT interconnect on a VLT switch and enter interface configuration mode. CONFIGURATION mode interface port-channel id-number Enter the same port-channel number configured with the peer-link port-channel command as described in Enabling VLT and Creating a VLT Domain. NOTE: To be included in the VLTi, the port channel must be in Default mode (no switchport or VLAN assigned). 2.
PAGE 974
4. Enable peer routing. VLT DOMAIN CONFIGURATION mode peer-routing If you enable peer routing, a VLT node acts as the proxy gateway for its peer. 5. (Optional) After you configure a VLT domain on each peer switch and connect (cable) the two VLT peers on each side of the VLT interconnect, the system elects a primary and secondary VLT peer device (see Primary and Secondary VLT Peers). To configure the primary and secondary roles before the election process, use the primary-priority command.
PAGE 975
CONFIGURATION mode delay-restore delay-restore-time The range is from 1 to 1200. The default is 90 seconds. Reconfiguring the Default VLT Settings (Optional) To reconfigure the default VLT settings, use the following commands. 1. Enter VLT-domain configuration mode for a specified VLT domain. CONFIGURATION mode vlt domain domain-id The range of domain IDs is from 1 to 1000. 2.
PAGE 976
switchport 4. Add one or more port interfaces to the port channel. INTERFACE PORT-CHANNEL mode channel-member interface interface: specify one of the following interface types: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 5. Ensure that the port channel is active. INTERFACE PORT-CHANNEL mode no shutdown 6.
PAGE 977
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 3. Enter VLT-domain configuration mode for a specified VLT domain. CONFIGURATION mode vlt domain domain-id The range of domain IDs is from 1 to 1000. 4. Enter the port-channel number that acts as the interconnect trunk. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 5.
PAGE 978
INTERFACE mode port-channel-protocol lacp 14. Configure the LACP port channel mode. INTERFACE mode port-channel number mode [active] 15. Ensure that the interface is active. MANAGEMENT INTERFACE mode no shutdown 16. Enable peer routing. VLT DOMAIN CONFIGURATION mode peer-routing If you enable peer routing, a VLT node acts as the proxy gateway for its peer. 17. Repeat steps 1 through 16 for the VLT peer node in Domain 1. 18. Repeat steps 1 through 16 for the first VLT node in Domain 2. 19.
PAGE 979
show running-config entity 12. Verify that VLT is running. EXEC mode show vlt brief or show vlt detail 13. Verify that the VLT LAG is running in both VLT peer units. EXEC mode or EXEC Privilege mode show interfaces interface In the following sample VLT configuration steps, VLT peer 1 is Dell-2, VLT peer 2 is Dell-4, and the ToR is S60-1. NOTE: If you use a third-party ToR unit, Dell EMC Networking recommends using static LAGs with VLT peers to avoid potential problems if you reboot the VLT peers.
PAGE 980
! port-channel-protocol LACP port-channel 2 mode active no shutdown configuring VLT peer lag in VLT Dell-2#show running-config interface port-channel 2 ! interface Port-channel 2 no ip address switchport vlt-peer-lag port-channel 2 no shutdown Dell-2#show interfaces port-channel 2 brief Codes: L - LACP Port-channel L LAG 2 Mode L2L3 Status up Uptime 03:33:14 Ports Te 1/4 (Up) In the ToR unit, configure LACP on the physical ports.
PAGE 981
Delay-Restore Abort Threshold Peer-Routing Peer-Routing-Timeout timer Multicast peer-routing timeout DellEMC# : : : : 60 seconds Disabled 0 seconds 150 seconds Verify that the VLT LAG is up in VLT peer unit.
PAGE 982
Name ---------Po 1 Po 2 Te 1/10 Te 1/13 PortID -------128.2 128.3 128.230 128.233 Interface Name ---------Po 1 Po 2 Te 1/10 Te 1/13 DellEMC# Role -----Desg Desg Desg Desg Prio ---128 128 128 128 Cost -----188 2000 2000 2000 PortID -------128.2 128.3 128.230 128.233 Prio ---128 128 128 128 Sts Cost Bridge ID PortID ----------- ------- -------------------- -------FWD(vltI) 0 0 90b1.1cf4.9b79 128.2 FWD(vlt) 0 0 90b1.1cf4.9b79 128.3 FWD 0 0 90b1.1cf4.9b79 128.230 FWD 0 0 90b1.1cf4.9b79 128.
PAGE 983
Figure 144. Peer Routing Configuration Example Dell-1 Switch Configuration In the following output, RSTP is enabled with a bridge priority of 0. This ensures that Dell-1 becomes the root bridge. DellEMC#1#show run | find protocol protocol spanning-tree pvst no disable vlan 1,20,800,900 bridge-priority 0 The following output shows the existing VLANs.
PAGE 984
(The management interfaces are part of a default VRF and are isolated from the switch’s data plane.) In Dell-1, te 0/0 and te 0/1 are used for VLTi. DellEMC#1#sh run int te0/0 interface TenGigabitEthernet 0/0 description VLTi LINK no ip address no shutdown (VLTi Physical link) ! DellEMC#1#sh run int te0/1 interface TenGigabitEthernet 0/1 description VLTi LINK no ip address no shutdown (VLTi Physical link) The following example shows that te 0/0 and te 0/1 are included in port channel 10.
PAGE 985
Vlan 20 is used in Dell-1, Dell-2, and R1 to form OSPF adjacency. When OSPF is converged, the routing tables in all devices are synchronized. DellEMC#1#sh run int vlan 20 interface Vlan 20 description OSPF PEERING VLAN ip address 192.168.20.1/29 untagged Port-channel 1 no shutdown ! DellEMC#1#sh run int vlan 800 interface Vlan 800 description Client-VLAN ip address 192.168.8.1/24 tagged Port-channel 2 no shutdown The following output shows Dell-1 is configured with VLT domain 1.
PAGE 986
Use the show vlt detail command to verify that VLT is functional and that the correct VLANs are allowed. DellEMC#1#sh vlt detail Local LAG Id -----------1 2 Peer LAG Id ----------1 2 Local Status -----------UP UP Peer Status ----------UP UP Active VLANs ------------20 1, 800, 900 The following output displays the OSPF configuration in Dell-1 DellEMC#1#sh run | find router router ospf 1 router-id 172.17.1.1 network 192.168.9.0/24 area 0 network 192.168.8.0/24 area 0 network 172.17.1.
PAGE 987
0 0 90:b1:1c:f4:2c:bd 90:b1:1c:f4:29:f3 LOCAL_DA LOCAL_DA 00001 00001A The above output shows that the 90:b1:1c:f4:2c:bd MAC address belongs to Dell-1. The 90:b1:1c:f4:29:f3 MAC address belongs to Dell-2. Also note that these MAC addresses are marked with LOCAL_DA. This means, these are the local destination MAC addresses used by hosts when routing is required. Packets sent to this MAC address are directly forwarded to their destinations without being sent to the peer switch.
PAGE 988
no ip address port-channel-protocol LACP port-channel 2 mode active no shutdown Te 0/6 connects to the uplink switch R1. Dell-2#sh run int te0/6 interface TenGigabitEthernet 0/6 description To_CR1_fa0/13 no ip address port-channel-protocol LACP port-channel 1 mode active no shutdown Port channel 1 connects the uplink switch R1.
PAGE 989
Verify if VLT on Dell-1 is functional Dell-2#sh vlt brief VLT Domain Brief -----------------Domain ID: Role: Role Priority: 1 Secondary 55000 ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Peer routing : Peer routing-Timeout timer: Multicast peer routing timeout: Up Up Up 1 6(3) 90:b1:1c:f4:29:f1 90:b1:1c:f4:2c:bb 90:b1:1c:f4:01:01 6(3) 90 seconds En
PAGE 990
The following output displays the routes learned using OSPF. Dell-2 also learns the routes to the loopback addresses on R1 through OSPF. Dell-2#show ip route ospf Destination Gateway ----------------O 2.2.2.2/24 via 192.168.20.3, O 3.3.3.2/24 via 192.168.20.3, O 4.4.4.2/24 via 192.168.20.3, O 172.15.1.1/32 via 192.168.20.3, O 172.16.1.2/32 via 192.168.20.
PAGE 991
network 172.15.1.0 0.0.0.255 area 0 network 192.168.20.0 0.0.0.7 area 0 CR1#show ip ospf neighbor (R1 is a DROTHER) Neighbor ID Pri State Dead Time Address Interface 172.16.1.2 1 FULL/BDR 00:00:31 192.168.20.2 Port-channel1 172.17.1.1 1 FULL/DR 00:00:38 192.168.20.1 Port-channel1 CR1#show ip route (Output Truncated) 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Loopback2 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, Loopback3 O 192.168.8.0/24 [110/2] via 192.168.
PAGE 992
Figure 145. eVLT Configuration Example eVLT Configuration Step Examples In Domain 1, configure the VLT domain and VLTi on Peer 1. Domain_1_Peer1#configure Domain_1_Peer1(conf)#interface port-channel 1 Domain_1_Peer1(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-9 Domain_1_Peer1(conf)#vlt domain 1000 Domain_1_Peer1(conf-vlt-domain)# peer-link port-channel 1 Domain_1_Peer1(conf-vlt-domain)# back-up destination 10.16.130.
PAGE 993
Configure eVLT on Peer 2. Domain_1_Peer2(conf)#interface port-channel 100 Domain_1_Peer2(conf-if-po-100)# switchport Domain_1_Peer2(conf-if-po-100)# vlt-peer-lag port-channel 100 Domain_1_Peer2(conf-if-po-100)# no shutdown Add links to the eVLT port-channel on Peer 2.
PAGE 994
PIM-Sparse Mode Configuration Example The following sample configuration shows how to configure the PIM Sparse mode designated router functionality on the VLT domain with two VLT port-channels that are members of VLAN 4001. For more information, refer to PIM-Sparse Mode Support on VLT. Examples of Configuring PIM-Sparse Mode The following example shows how to enable PIM multicast routing on the VLT node globally.
PAGE 995
EXEC mode show vlt role ● Display the current configuration of all VLT domains or a specified group on the switch. EXEC mode show running-config vlt ● Display statistics on VLT operation. EXEC mode show vlt statistics ● Display the RSTP configuration on a VLT peer switch, including the status of port channels used in the VLT interconnect trunk and to connect to access devices. EXEC mode show spanning-tree rstp ● Display the current status of a port or port-channel interface used in the VLT domain.
PAGE 996
Delay-Restore Abort Threshold Peer-Routing Peer-Routing-Timeout timer Multicast peer-routing timeout DellEMC# : : : : 60 seconds Disabled 0 seconds 150 seconds The following example shows the show vlt detail command.
PAGE 997
VLT Statistics ---------------HeartBeat Messages Sent: HeartBeat Messages Received: ICL Hello's Sent: ICL Hello's Received: 994 978 89 89 The following example shows the show spanning-tree rstp command. The bold section displays the RSTP state of port channels in the VLT domain. Port channel 100 is used in the VLT interconnect trunk (VLTi) to connect to VLT peer2. Port channels 110, 111, and 120 are used to connect to access switches or servers (vlt).
PAGE 998
Configure the backup link. Dell_VLTpeer1(conf)#interface ManagementEthernet 0/0 Dell_VLTpeer1(conf-if-ma-0/0)#ip address 10.11.206.23/ Dell_VLTpeer1(conf-if-ma-0/0)#no shutdown Dell_VLTpeer1(conf-if-ma-0/0)#exit Configure the VLT interconnect (VLTi).
PAGE 999
Dell_VLTpeer2(conf-if-po-110)#vlt-peer-lag port-channel 110 Dell_VLTpeer2(conf-if-po-110)#end Verify that the port channels used in the VLT domain are assigned to the same VLAN.
PAGE 1000
Table 138. Troubleshooting VLT (continued) Description Behavior at Peer Up Behavior During Run Time Action to Take A one-time informational syslog message is generated. To resolve, enable RSTP on both VLT peers. A one-time informational syslog message is generated. Correct the spanning tree configuration on the ports. Spanning tree mismatch at port level A syslog error message is generated.
PAGE 1001
Specifying VLT Nodes in a PVLAN You can configure VLT peer nodes in a private VLAN (PVLAN). VLT enables redundancy without the implementation of Spanning Tree Protocol (STP), and provides a loop-free network with optimal bandwidth utilization. Because the VLT LAG interfaces are terminated on two different nodes, PVLAN configuration of VLT VLANs and VLT LAGs are symmetrical and identical on both the VLT peers. PVLANs provide Layer 2 isolation between ports within the same VLAN.
PAGE 1002
MAC Synchronization for VLT Nodes in a PVLAN For the MAC addresses that are learned on non-VLT ports, MAC address synchronization is performed with the other peer if the VLTi (ICL) link is part of the same VLAN as the non-VLT port. For MAC addresses that are learned on VLT ports, the VLT LAG mode of operation and the primary to secondary association of the VLT nodes is determined on both the VLT peers.
PAGE 1003
Scenarios for VLAN Membership and MAC Synchronization With VLT Nodes in PVLAN The following table illustrates the association of the VLTi link and PVLANs, and the MAC synchronization of VLT nodes in a PVLAN (for various modes of operations of the VLT peers): Table 139.
PAGE 1004
Table 139.
PAGE 1005
7. Enter the port-channel number that acts as the interconnect trunk. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 8. (Optional) To configure a VLT LAG, enter the VLAN ID number of the VLAN where the VLT forwards packets received on the VLTi from an adjacent peer that is down. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number peer-down-vlan vlan interface number Associating the VLT LAG or VLT VLAN in a PVLAN 1.
PAGE 1006
By default, proxy ARP is enabled. To disable proxy ARP, use the no proxy-arp command in Interface mode. To re-enable proxy ARP, use the ip proxy-arp command in Interface mode. To view if proxy ARP is enabled on the interface, use the show config command in INTERFACE mode. If it is not listed in the show config command output, it is enabled. Only nondefault information displays in the show config command output.
PAGE 1007
VLT Nodes as Rendezvous Points for Multicast Resiliency You can configure VLT peer nodes as rendezvous points (RPs) in a Protocol Independent Multicast (PIM) domain. PIM uses a VLT node as the RP to distribute multicast traffic to a multicast group. Messages to join the multicast group (Join messages) and data are sent towards the RP, so that receivers can discover who the senders are and begin receiving traffic destined for the multicast group.
PAGE 1008
DellEMC(conf-vlt-domain)#peer-link port-channel 1 DellEMC(conf-vlt-domain)#back-up destination 10.16.151.116 DellEMC(conf-vlt-domain)#primary-priority 100 DellEMC(conf-vlt-domain)#system-mac mac-address 00:00:00:11:11:11 DellEMC(conf-vlt-domain)#unit-id 0 DellEMC(conf-vlt-domain)# DellEMC#show running-config vlt ! vlt domain 1 peer-link port-channel 1 back-up destination 10.16.151.
PAGE 1009
Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged NUM 50 Status Active Description DellEMC# Q M M V Ports Po10(Te 1/8) Po20(Te 1/12) Po1(Te 1/30-32) Sample Configuration of VLAN-Stack Over VLT (Peer 2) Configure
PAGE 1010
DellEMC(conf-if-vl-50-stack)#member port-channel 10 DellEMC(conf-if-vl-50-stack)#member port-channel 20 DellEMC(conf-if-vl-50-stack)# DellEMC#show running-config interface vlan 50 ! interface Vlan 50 vlan-stack compatible member Port-channel 10,20 shutdown DellEMC# Verify that the Port Channels used in the VLT Domain are Assigned to the VLAN-Stack VLAN DellEMC#show vlan id 50 Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow Q: U
PAGE 1011
node, node2, owing to LAG-level hashing in the ToR switch, it is routed instead of forwarding the packet to node1. This processing occurs because of the match or hit for the entry in the TCAM of the VLT node2. Synchronization of IPv6 ND Entries in a VLT Domain Because the VLT nodes appear as a single unit, the ND entries learned via the VLT interface are expected to be the same on both VLT nodes.
PAGE 1012
Figure 146. Sample Configuration of IPv6 Peer Routing in a VLT Domain Sample Configuration of IPv6 Peer Routing in a VLT Domain Consider a sample scenario as shown in the following figure in which two VLT nodes, Unit1 and Unit2, are connected in a VLT domain using an ICL or VLTi link. To the south of the VLT domain, Unit1 and Unit2 are connected to a ToR switch named Node B. Also, Unit1 is connected to another node, Node A, and Unit2 is linked to a node, Node C.
PAGE 1013
Consider a case in which NS for VLT node1 IP reaches VLT node1 on the VLT interface and NS for VLT node1 IP reaches VLT node2 due to LAG level hashing in the ToR. When VLT node1 receives NS from VLT VLAN interface, it unicasts the NA packet on the VLT interface. When NS reaches VLT node2, it is flooded on all interfaces including ICL. When VLT node 1 receives NS on ICL, it floods the NA packet on the VLAN. If NS is unicast and if it reaches the wrong VLT peer, it is lifted to the CPU using ACL entry.
PAGE 1014
When VLT node receives traffic from non-VLT host intended to VLT host, it routes the traffic to VLT interface. If VLT interface is not operationally up VLT node will route the traffic over ICL. Non-VLT host to North Bound traffic flow When VLT node receives traffic from non-VLT host intended to north bound with DMAC as self MAC it routes traffic to next hop.
PAGE 1015
ToR 1. Enable BFD globally. TOR(conf)# bfd enable 2. Configure a VLT peer LAG. TOR(conf)#interface tengigabitethernet 1/1 TOR(conf-if-te-1/1)#no ip address TOR(conf-if-te-1/1)#port-channel-protocol lacp TOR(conf-if-te-1/1)#port-channel 10 mode active TOR(conf-if-te-1/1)#no shutdown TOR(conf)#interface tengigabitethernet 1/2 TOR(conf-if-te-1/2)#no ip address TOR(conf-if-te-1/2)#port-channel-protocol lacp TOR(conf-if-te-1/2)#port-channel 10 mode active TOR(conf-if-te-1/2)#no shutdown 3.
PAGE 1016
5. Enable BFD over OSPF. TOR(conf)# router ospf 1 TOR(conf-router_ospf)# network 100.1.1.0/24 area 0 TOR(conf-router_ospf)# bfd all-neighbors VLT Primary 1. Enable BFD globally. VLT_Primary(conf)# bfd enable 2. Configure port channel which is used as VLTi link. VLT_Primary(conf)# interface VLT_Primary(conf-if-po-100)# VLT_Primary(conf-if-po-100)# VLT_Primary(conf-if-po-100)# port-channel 100 no ip address channel-member tengigabitethernet 1/1, 1/2 no shutdown 3. Enable VLT and configure a VLT domain.
PAGE 1017
2. Configure port channel which is used as VLTi link. VLT_Secondary(conf)# interface VLT_Secondary(conf-if-po-100)# VLT_Secondary(conf-if-po-100)# VLT_Secondary(conf-if-po-100)# port-channel 100 no ip address channel-member tengigabitethernet 1/1, 1/2 no shutdown 3. Enable VLT and configure a VLT domain. VLT_Secondary(conf)# vlt domain VLT_Secondary(conf-vlt-domain)# VLT_Secondary(conf-vlt-domain)# VLT_Secondary(conf-vlt-domain)# 100 peer-link port-channel 100 back-up destination 10.16.206.
PAGE 1018
Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: 60 seconds Enabled 0 seconds 150 seconds ● To verify the VLTi (ICL) link is up in the VLT secondary peer, use show vlt brief command.
PAGE 1019
Static VXLAN Configuration in a VLT setup Configuration steps are covered below: 1. Both Gateway VTEPs need VLT configured. ● ICL port configuration interface Port-channel 1 no ip address channel-member TenGigabitEthernet 0/4-5 no shutdown ● VLT Domain Configuration vlt domain 100 peer-link port-channel 1 back-up destination 10.11.70.14  this is ip address of the peer node ● VXLAN Instance Configuration vxlan-instance 1 static local-vtep-ip 14.14.14.
PAGE 1020
vni-profile test vnid 200 remote-vtep-ip 3.3.3.3 vni-profile test ● VLT Access port configuration interface TengigabitEthernet 0/12 port-channel-protocol lacp port-channel 30 mode active interface Port-channel 30 no ip address vxlan-instance 1 switchport vlt-peer-lag port-channel 30 no shutdown 2. Configure loopback interface and VXLAN instances on both the peers. ● Configure loopback interface IP address on both peers with the same IPaddress. interface Loopback 1 ip address 14.14.14.14/32 no shutdown 3.
PAGE 1021
59 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1022
Figure 148. Sample Configuration for a VLT Proxy Gateway Guidelines for Enabling the VLT Proxy Gateway Keep the following points in mind when you enable a VLT proxy gateway: ● Proxy gateway is supported only for VLT; for example, across a VLT domain. ● You must enable the VLT peer-routing command for the VLT proxy gateway to function.
PAGE 1023
● Private VLANs (PVLANs) are not supported. ● When a Virtual Machine (VM) moves from one VLT domain to the another VLT domain, the VM host sends the gratuitous ARP (GARP) , which in-turn triggers a mac movement from the previous VLT domain to the newer VLT domain. ● After a station move, if the host sends a TTL1 packet destined to its gateway; for example, a previous VLT node, the packet can be dropped.
PAGE 1024
● You must globally enable LLDP. ● You cannot have interface–level LLDP disable commands on the interfaces configured for proxy gateway and you must enable both transmission and reception. ● You must connect both units of the remote VLT domain by the port channel member. ● If you connect more than one port to a unit of the remote VLT domain, the connection must be completed by the time you enable the proxy gateway LLDP.
PAGE 1025
● The preceding figure shows a sample square VLT Proxy gateway topology. There are no diagonal links in the square VLT connection between the C and D in VLT domain 1 and C1 and D1 in the VLT domain 2. This causes sub-optimal routing. For VLT Proxy Gateway to work in this scenario you must configure the VLT-peer-mac transmit command under VLT Domain Proxy Gateway LLDP mode, in both C and D (VLT domain 1) and C1 and D1 (VLT domain 2).
PAGE 1026
2. Configure peer-domain-link port-channel in VLT Domain Proxy Gateway LLDP mode. The VLT port channel is the one that connects the remote VLT domain. Sample Dynamic Proxy Configuration on C switch or C1 switch Switch_C#conf Switch_C(conf)#vlt domain 1 Switch_C(conf-vlt-domain1)#proxy-gateway lldp Switch_C(conf-vlt-domain1-pxy-gw-lldp)#peer-domain-link port-channel 1....
PAGE 1027
The MAC addresses, configured using the remote-mac-address command, belong to Dell-3 and Dell-4.
PAGE 1028
remote-mac-address 00:01:e8:8b:ff:4f remote-mac-address 00:01:e8:d8:93:04 The MAC addresses, configured using the remote-mac-address command, belong to Dell-3 and Dell-4. interface Vlan 100 description OSPF peering VLAN to Dell-1 ip address 10.10.100.2/30 ip ospf network point-to-point no shutdown The following is the OSPF configuration on Dell-2. router ospf 1 router-id 2.2.2.2 network 10.10.100.0/30 area 0 The following output shows that Dell-1 forms OSPF neighborship with Dell-2.
PAGE 1029
interface Vlan 102 description ospf peering vlan to DELL-4 ip address 10.10.102.1/30 ip ospf network point-to-point no shutdown The following is the OSPF configuration on Dell-3. router ospf 1 router-id 3.3.3.3 network 10.10.101.0/30 area 0 network 10.10.102.0/30 area 0 The following output shows that Dell-4 and VLT domain 120 form OSPF neighborship with Dell-3. Dell-3#sh ip ospf nei ! Neighbor ID Pri State Dead Time Address Interface Area 4.4.4.4 1 FULL/ - 00:00:33 10.10.101.1 Vl 101 0 1.1.1.
PAGE 1030
60 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS. Overview The switch acts as the VXLAN gateway and performs the VXLAN Tunnel End Point (VTEP) functionality. VXLAN is a technology where in the data traffic from the virtualized servers is transparently transported over an existing legacy network. Figure 151. VXLAN Gateway NOTE: In a stack setup, the Dell EMC Networking OS does not support VXLAN.
PAGE 1031
• • Routing in and out of VXLAN tunnels NSX Controller-based VXLAN for VLT Components of VXLAN network VXLAN provides a mechanism to extend an L2 network over an L3 network. In short, VXLAN is an L2 overlay scheme over an L3 network and this overlay is termed as a VXLAN segment.
PAGE 1032
Service Node(SN) It is also another VTEP, but it is fully managed by the controller. The purpose of SN is to be the central replication engine for flooded packets Legacy TOR It is a TOR switch, which performs routing or switching decisions. Functional Overview of VXLAN Gateway The following section is the functional overview of VXLAN Gateway: 1. Provides connectivity between a Virtual server infrastructure and a Physical server infrastructure. 2.
PAGE 1033
● Destination Address: Generally, it is a first hop router's MAC address when the VTEP is on a different address. ● Source Address : It is the source MAC address of the router that routes the packet. ● VLAN: It is optional in a VXLAN implementation and will be designated by an ethertype of 0×8100 and has an associated VLAN ID tag. ● Ethertype: It is set to 0×0800 because the payload packet is an IPv4 packet.
PAGE 1034
Configuring and Controlling VXLAN from the NSX Controller GUI You can configure and control VXLAN from the NSX controller GUI, by adding a hardware device to NSX and authenticating the device. 1. Generate a certificate in your system and add it to the NSX before adding a hardware device for authentication. To generate a certificate, use the following command: ● crypto cert generate self-signed cert-file flash://vtep-cert.pem key-file flash:// vtep-privkey.
PAGE 1035
Figure 153. Create VXLAN Gateway To create a VXLAN L2 Gateway, the IP address of the Gateway is required. After connectivity is established between the VTEP and NSX controller, the management IP address and the connectivity status are populated as shown in the following image. Figure 154. Hardware Devices 3. Add a service node or replicator. Under Home > Networking and Security > Service Definition > Hardware Devices > Replication Cluster, click the Edit button.
PAGE 1036
Figure 155. Add Service Node or Replicator NOTE: Ensure L3 reachability between the VTEP and the replicator. 4. Create Logical Switch. You can create a logical network by creating a logical switch. The logical network acts as the forwarding domain for workloads on the physical as well as virtual infrastructure. Click Home > Networking and Security > Logical Switches and click Add. The New Logical Switch window opens. Enter a name and select Unicast as the replication mode and click OK. Figure 156.
PAGE 1037
In the Manage Hardware Bindings window, expand a VTEP and click Add. The Manage Hardware Bindings Window opens. Click the Select link and the Specify Hardware Port window opens. Click the hardware port and click OK. Figure 157. Specify Hardware Port In the Manage Hardware Bindings window, under the VLAN column, enter the VLAN ID and press OK. Figure 158. Create Logical Switch Port 6. (Optional) Enable or disable BFD globally. Go to Hardware Devices tab > BFD Configuration, and click the Edit button.
PAGE 1038
Figure 159. Edit VXLAN BFD Configuration NOTE: For more details about NSX controller configuration, refer to the NSX user guide from VMWare . Configuring and Controling VXLAN from Nuage Controller GUI The Dell EMC Networking OS supports Nuage controller for VXLAN. You can configure and control VXLAN from the Nuage controller GUI, by adding a hardware device to the Nuage controller and authenticating the device. 1. Under the Infrastructure tab, add a datacenter gateway. Figure 160.
PAGE 1039
Figure 161. Port-to-VLAN mappings 3. Under the Networks tab, create an L2 domain. Under the L2 domain, create a logical network (VNI) and add access ports of the VTEP in the logical network. Figure 162. Access ports of the VTEP Configuring VxLAN Gateway To configure the VxLAN gateway on the switch, follow these steps: 1. Connecting to NVP controller 2. Advertising VXLAN access ports to controller Connecting to an NVP Controller To connect to an NVP controller, use the following commands. 1.
PAGE 1040
3. Define how the device connects to the controller. VxLAN INSTANCE mode controller controller ID ip address port port-number TCP | SSL The port number range is from 1 to 6632. The default connection type is SSL. TCP, PTCP, and PSSL are supported with NSX controller only. 4. Enter the gateway IP VxLAN INSTANCE mode gateway-ip IP address 5. Enter the maximum backoff time (Optional). VxLAN INSTANCE mode max_backoff time The range is from 1000-180000. The default value is 30000 milliseconds. 6.
PAGE 1041
The following example shows the show vxlan vxlan-instance logical-network command. • show vxlan vxlan-instance 1 logical-network Instance : 1 Total LN count : 1024 * - No VLAN mapping exists and yet to be installed Name VNID 1ba08465-8774-3383-ba51-8b7e642ff632 6427 02f063c2-36c7-3ef6-a324-b432b748d15d 6218 36ab6265-5fa8-3ce8-b35c-e7cfdaf7c9e8 6368 The following example shows the show vxlan vxlan-instance statistics interface command.
PAGE 1042
Examples of the show bfd neighbors command. To verify that the session is established, use the show bfd neighbors command. Dell_GW1#show bfd neighbors * Ad Dn B C I O O3 R M V VT * * * * * * - Active session role Admin Down BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr 1.0.1.1 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 3.3.3.3 RemoteAddr 1.0.1.2 192.168.122.135 192.168.122.136 192.168.122.137 192.168.122.138 192.168.122.
PAGE 1043
VNI-PROFILE mode vnid VNID Range 6. Create a remote tunnel and associate the remote VTEP to the VNID. VXLAN-INSTANCE mode remote—vtep—ip remote IP Address vni-profile profile name 7. Enable the VXLAN. VXLAN-INSTANCE mode no shutdown 8. Enable VXLAN instance on the interface. The interface should not be on layer 2. INTERFACE mode vxlan-instance Instance ID 9. Associate VNID to VLAN.
PAGE 1044
Use the following command to clear the remote VTEP and access port statistics. DellEMC# clear vxlan vxlan-instance 1 statistics Disabling MAC Address Learning on Static VXLAN Tunnels You can configure the system to not learn MAC addresses on static VXLAN tunnels or remote VTEPs. MAC address learning on static VXLAN tunnels is Enabled by default.
PAGE 1045
Following is the output of show ip routecommand for the above connection: DellEMC# show ip route Destination Gateway --------------- Dist/Metric Last ----------- *B IN 0.0.0.0/0 C 1.1.1.1/32 B IN 2.2.2.2/32 200/0 0/0 200/0 via 192.168.11.2 Direct, Lo 1 via 192.168.22.1 Change ----------16:13:30 8:59:34 00:36:48 From the above routing table it is understood that the remote VTEP 2.2.2.2/32 is resolved through next-hop 192.168.22.1, which is not directly connected.
PAGE 1046
In this RIOT scheme, whenever R1 tries to reach R2, the packet gets to P1 on VTEP 1 with VLAN 10 and gets routed out of P2 on VLAN 20. VTEP 1 sends an ARP request for R2 (10.1.2.1) through P2. This request gets VXLAN encapsulated at P3 and is sent out of P4. Eventually, the native ARP request reaches R2. R2 sends an ARP response that is VXLAN encapsulated at VTEP 2. This response reaches VTEP 1 on P4 with a VXLAN encapsulation. At this point, the ARP response is de-capsulated at P4.
PAGE 1047
The topology to achieve RIOT with a physical loopback is inherently susceptible to Layer 2 loops. To prevent these loops from disrupting the network, the following egress masks need to be applied: ● ● ● ● Any Any Any Any frame frame frame frame ingressing ingressing ingressing ingressing on on on on a a a a VXLAN access port is not allowed to egress out of a VXLAN loopback port. VXLAN loopback port is not allowed to egress out of a VXLAN access port.
PAGE 1048
In this topology, P2 and P3 in VTEP 1 are VLT port-channels with corresponding VLT peer LAGs being P2 and P3 in VTEP 2. Similarly, P6 and P7 in VTEP 3 are VLT port-channels with corresponding VLT peer LAGs being P6 and P7 in VTEP 4. NOTE: P2, P3, P6, and P7 can be a single port or multi-port port-channels that are VLT port-channels. NOTE: The VLT VXLAN configuration for RIOT deviates from the standard VLT behavior when these physical loopbacks are provisioned as VLT port-channels.
PAGE 1049
Figure 164. Controller-based VXLAN for VLT Providing Redundancy Important Points to Remember ● The VLT peer port channel number must be the same on both VLT peers. ● before configuring controller-based VXLAN with VLT, remove any existing standalone VXLAN configuration. ● BFD tunnels come up only after the NSX controller sends tunnel details. The details come after the remote MAC addresses are downloaded from NSX controller.
PAGE 1050
bfd enable Enter the result of your step here (optional). 2. Create an uplink-state group. CONFIGURATION mode uplink-state-group group-id group-id: values are from 1 to 16. 3. Assign a VLT port channel to the uplink-state group as an upstream link. UPLINK-STATE-GROUP mode upstream interface 4. Assign a network port or port channel to the uplink-state group as a downstream link.
PAGE 1051
vlt domain domain-id The domain ID range is from 1 to 1000. Configure the same domain ID on the peer switch 2. Configure the IP address of the management interface on the remote VLT peer to be used as the endpoint of the VLT backup link for sending out-of-band hello messages. VLT DOMAIN CONFIGURATION mode back-up destination ip-address 3. Configure the port channel to be used as the VLT interconnect between VLT peers in the domain. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 4.
PAGE 1052
vlt-peer-lag port-channel 10 no shutdown The following are some of the show command outputs on the VLT primary: DellEMC#show vlt brief VLT Domain Brief -----------------Domain ID: Role: Role Priority: ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: D
PAGE 1053
Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated O - Openflow, Vx - Vxlan Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged * NUM 1 Status Active Vx 20 Active 500 Active Description DellEMC# DellEMC# DellEMC#sh vxlan vxlan-instance 1 multicast-mac * - Active Replicator
PAGE 1054
Role Priority: ICL Link Status: HeartBeat Status: VLT Peer Status: Local Unit Id: Version: Local System MAC address: Remote System MAC address: Configured System MAC address: Remote system version: Delay-Restore timer: Delay-Restore Abort Threshold: Peer-Routing : Peer-Routing-Timeout timer: Multicast peer-routing timeout: DellEMC# DellEMC# DellEMC# 10 Up Up Up 1 6(8) f4:8e:38:2b:3e:85 14:18:77:0a:53:80 00:00:00:11:11:11 6(8) 90 seconds 60 seconds Enabled 0 seconds 150 seconds DellEMC#sh vxlan vxlan-insta
PAGE 1055
Tunnel : count 1 6.6.6.2 : vxlan_over_ipv4 (up) DellEMC#show vxlan vxlan-instance 1 unicast-mac-local Total Local Mac Count: 1 VNI MAC PORT 5000 00:00:00:cc:00:00 (N) Po 1 VLAN 20 DellEMC#show vxlan vxlan-instance 1 unicast-mac-remote Total Remote Mac Count: 1 VNI MAC TUNNEL 5000 00:00:bb:00:00:00 4.3.3.
PAGE 1056
Copy and paste the generated certificate to the NSX. NOTE: Once controller connectivity is established from VLT peers, if you want to generate a new certificate and use it for controller connection, generate the certificate from the node (node that is directly connected to controller). If you do not generate a new certificate from the node, system shows inconsistent behavior. 2. Create a VXLAN Gateway. To create service node, the required fields are the IP address and SSL certificate of the server.
PAGE 1057
Figure 166. Hardware Devices 3. Add a service node or replicator. Under Home > Networking and Security > Service Definition > Hardware Devices > Replication Cluster, click the Edit button. Select required hosts for replication and click OK. Figure 167. Add Service Node or Replicator NOTE: Ensure L3 reachability between the VTEP and the replicator. 4. Create Logical Switch. You can create a logical network by creating a logical switch.
PAGE 1058
Figure 168. Create Logical Switch 5. Create Logical Switch Port. A logical switch port provides a logical connection point for a VM interface (VIF) and a L2 gateway connection to an external network. It binds the virtual access ports in the gateway to logical network (VXLAN) and VLAN. In the Manage Hardware Bindings window, expand a VTEP and click Add. The Manage Hardware Bindings Window opens. Click the Select link and the Specify Hardware Port window opens. Click the hardware port and click OK.
PAGE 1059
Figure 170. Create Logical Switch Port 6. (Optional) Enable or disable BFD globally. Go to Hardware Devices tab > BFD Configuration, and click the Edit button. The Edit BFD Configuration windows opens. Check or uncheck the Enable BFD check box. You can also change the probe interval if required. Figure 171. Edit VXLAN BFD Configuration NOTE: For more details about NSX controller configuration, refer to the NSX user guide from VMWare .
PAGE 1060
61 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows a physical router to partition itself into multiple Virtual Routers (VRs). The control and data plane are isolated in each VR so that traffic does NOT flow across VRs.Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist within the same router at the same time.
PAGE 1061
Figure 172. VRF Network Example VRF Configuration Notes Although there is no restriction on the number of VLANs that can be assigned to a VRF instance, the total number of routes supported in VRF is limited by the size of the IPv4 CAM. VRF is implemented in a network device by using Forwarding Information Bases (FIBs). A network device may have the ability to configure different virtual routers, where entries in the FIB that belong to one VRF cannot be accessed by another VRF on the same device.
PAGE 1062
VRF supports some routing protocols only on the default VRF (default-vrf) instance. Table 1 displays the software features supported in VRF and whether they are supported on all VRF instances or only the default VRF. NOTE: To configure a router ID in a non-default VRF, configure at least one IP address in both the default as well as the non-default VRF. Table 140. Software Features Supported on VRF Feature/Capability Support Status for Default VRF Support Status for Non-default VRF 802.
PAGE 1063
DHCP DHCP requests are not forwarded across VRF instances. The DHCP client and server must be on the same VRF instance. VRF Configuration The VRF configuration tasks are: 1. Enabling VRF in Configuration Mode 2. Creating a Non-Default VRF 3. Assign an Interface to a VRF You can also: ● View VRF Instance Information ● Connect an OSPF Process to a VRF Instance ● Configure VRRP on a VRF Loading VRF CAM ● Load CAM memory for the VRF feature.
PAGE 1064
interface tengigabitethernet 1/1 2. Assign the interface to management VRF. INTERFACE CONFIGURATION ip vrf forwarding management Before assigning a front-end port to a management VRF, ensure that no IP address is configured on the interface. 3. Assign an IPv4 address to the interface. INTERFACE CONFIGURATION ip address 10.1.1.1/24 Before assigning a front-end port to a management VRF, ensure that no IP address is configured on the interface. 4. Assign an IPv6 address to the interface.
PAGE 1065
Table 141. Configuring VRRP on a VRF (continued) Task Command Syntax Assign an IP address to the interface Configure the VRRP group and virtual IP address View VRRP command output for the VRF vrf1 Command Mode ip address 10.1.1.1 /24 no shutdown vrrp-group 10 virtual-address 10.1.1.100 show config ----------------------------! interface TenGigabitEthernet 1/13 ip vrf forwarding vrf1 ip address 10.1.1.1/24 ! vrrp-group 10 virtual-address 10.1.1.
PAGE 1066
● ● ● ● ● ● ● ipv6 ipv6 ipv6 ipv6 ipv6 ipv6 ipv6 nd ra-lifetime — Set IPv6 Router Advertisement Lifetime nd reachable-time — Set advertised reachability time nd retrans-timer — Set NS retransmit interval used and advertised in RA nd suppress-ra — Suppress IPv6 Router Advertisements ad — IPv6 Address Detection ad autoconfig — IPv6 stateless auto-configuration address — Configure IPv6 address on an interface NOTE: The command line help still displays relevant details correspon
PAGE 1067
Figure 174. Setup VRF Interfaces The following example relates to the configuration shown in the above illustrations. Router 1 ip vrf blue 1 ! ip vrf orange 2 ! ip vrf green 3 ! interface TenGigabitEthernet no ip address switchport no shutdown ! interface TenGigabitEthernet ip vrf forwarding blue ip address 10.0.0.1/24 no shutdown ! interface TenGigabitEthernet ip vrf forwarding orange ip address 20.0.0.1/24 no shutdown ! interface TenGigabitEthernet ip vrf forwarding green ip address 30.0.0.
PAGE 1068
ip vrf forwarding blue ip address 1.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 192 ip vrf forwarding orange ip address 2.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.1 network 1.0.0.0/24 area 0 network 10.0.0.0/24 area 0 ! router ospf 2 vrf orange router-id 2.0.0.1 network 2.0.0.0/24 area 0 network 20.0.0.
PAGE 1069
! router ospf 1 vrf blue router-id 1.0.0.2 network 11.0.0.0/24 area 0 network 1.0.0.0/24 area 0 passive-interface TenGigabitEthernet 2/1 ! router ospf 2 vrf orange router-id 2.0.0.2 network 21.0.0.0/24 area 0 network 2.0.0.0/24 area 0 passive-interface TenGigabitEthernet 2/2 ! ip route vrf green30.0.0.0/24 3.0.0.1 ! The following shows the output of the show commands on Router 1.
PAGE 1070
Change Destination --------------------C 2.0.0.0/24 C 20.0.0.0/24 O 21.0.0.0/24 00:10:41 Gateway Dist/Metric ------- ----------- Direct, Vl 192 Direct, Te 1/2 via 2.0.0.
PAGE 1071
C 11.0.0.
PAGE 1072
Dynamic Route Leaking Route Leaking is a powerful feature that enables communication between isolated (virtual) routing domains by segregating and sharing a set of services such as VOIP, Video, and so on that are available on one routing domain with other virtual domains. Inter-VRF Route Leaking enables a VRF to leak or export routes that are present in its RTM to one or more VRFs.
PAGE 1073
ip route-import 1:1 5. Configure the export target in VRF-red. ip route-export 2:2 6. Configure VRF-blue. ip vrf vrf-blue interface-type slot/port ip vrf forwarding VRF-blue ip address ip—address mask A non-default VRF named VRF-blue is created and the interface 1/12 is assigned to it. 7. Configure the import target in VRF-blue. ip route-import 1:1 8. Configure the export target in VRF-blue. ip route-import 3:3 9. Configure VRF-green.
PAGE 1074
DellEMC# show ip route vrf VRF-Shared O 44.4.4.4/32 via 144.4.4.4 110/0 00:00:11 C 144.4.4.0/24 Direct, Te 1/4 0/0 00:32:36 Show routing tables of VRFs( after route-export and route-import tags are configured). DellEMC# show ip route vrf VRF-Red O C O C 11.1.1.1/32 111.1.1.0/24 44.4.4.4/32 144.4.4.0/24 via 111.1.1.1 110/0 00:00:10 Direct, Te 1/11 0/0 22:39:59 via VRF-shared:144.4.4.4 0/0 00:32:36 Direct, VRF-shared:Te 1/4 0/0 00:32:36 DellEMC# show ip route vrf VRF-Blue O 22.2.2.2/32 via 122.2.2.
PAGE 1075
You can use the match source-protocol or match ip-address commands to specify matching criteria for importing or exporting routes between VRFs. NOTE: You must use the match source-protocol or match ip-address commands in conjunction with the route-map command to be able to define the match criteria for route leaking. Consider a scenario where you have created two VRF tables VRF-red and VRF-blue. VRF-red exports routes with the export_ospfbgp_protocol route-map to VRF-blue.
PAGE 1076
The show run output for the above configuration is as follows: ip vrf vrf-Red ip route-export 1:1 export_ospfbgp_protocol ip route-import 2:2 ! this action exports only the OSPF and BGP routes to other VRFs ! ip vrf vrf-Blue ip route-export 2:2 ip route-import 1:1 import_ospf_protocol !this action accepts only OSPF routes from VRF-red even though both OSPF as well as BGP routes are shared The show VRF commands displays the following output: DellEMC# show ip route vrf VRF-Blue C 122.2.2.
PAGE 1077
62 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is designed to eliminate a single point of failure in a statically routed network. Topics: • • • • • • VRRP Overview VRRP Benefits VRRP Implementation VRRP Configuration Sample Configurations Proxy Gateway with VRRP VRRP Overview VRRP is designed to eliminate a single point of failure in a statically routed network.
PAGE 1078
Figure 175. Basic VRRP Configuration VRRP Benefits With VRRP configured on a network, end-station connectivity to the network is not subject to a single point-of-failure. Endstation connections to the network are redundant and are not dependent on internal gateway protocol (IGP) protocols to converge or update routing tables. In conjunction with Virtual Link Trunking (VLT), you can configure optimized forwarding with virtual router redundancy protocol (VRRP).
PAGE 1079
NOTE: In a VLT environment, VRRP configuration acts as active-active and if route is not present in any of the VRRP nodes, the packet to the destination is dropped on that VRRP node. Table 142.
PAGE 1080
The following examples how to configure VRRP. DellEMC(conf)#interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)#vrrp-group 111 DellEMC(conf-if-te-1/1-vrid-111)# The following examples how to verify the VRRP configuration. DellEMC(conf-if-te-1/1)#show conf ! interface TenGigabitEthernet 1/1 ip address 10.10.10.
PAGE 1081
3. Set the backup switches to version 3. Dell_backup_switch1(conf-if-te-1/1-vrid-100)#version 3 Dell_backup_switch2(conf-if-te-1/2-vrid-100)#version 3 Assign Virtual IP addresses Virtual routers contain virtual IP addresses configured for that VRRP group (VRID). A VRRP group does not transmit VRRP packets until you assign the Virtual IP address to the VRRP group.
PAGE 1082
virtual-address 10.10.10.1 virtual-address 10.10.10.2 virtual-address 10.10.10.3 ! vrrp-group 222 no shutdown The following example shows the same VRRP group (VRID 111) configured on multiple interfaces on different subnets. DellEMC#show vrrp -----------------TenGigabitEthernet 1/1, VRID: 111, Version: 2 Net: 10.10.10.1 VRF: 0 default State: Master, Priority: 255, Master: 10.10.10.
PAGE 1083
Virtual IP address: 10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10 Authentication: (none) -----------------TenGigabitEthernet 1/2, VRID: 111, Net: 10.10.2.1 VRF: 0 default State: Master, Priority: 125, Master: 10.10.2.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 601, Gratuitous ARP sent: 2 Virtual MAC address: 00:00:5e:00:01:6f Virtual IP address: 10.10.2.2 10.10.2.
PAGE 1084
● Prevent any BACKUP router with a higher priority from becoming the MASTER router. INTERFACE-VRID mode no preempt Re-enable preempt by entering the preempt command. When you enable preempt, it does not display in the show commands, because it is a default setting. The following example shows how to disable preempt using the no preempt command.
PAGE 1085
The following example shows how to change the advertise interval using the advertise-interval command. DellEMC(conf-if-te-1/1)#vrrp-group 111 DellEMC(conf-if-te-1/1-vrid-111)#advertise-interval 10 DellEMC(conf-if-te-1/1-vrid-111)# The following example shows how to verify the advertise interval change using the show conf command. DellEMC(conf-if-te-1/1-vrid-111)#show conf ! vrrp-group 111 advertise-interval 10 authentication-type simple 7 387a7f2df5969da4 no preempt priority 255 virtual-address 10.10.10.
PAGE 1086
● (Optional) Display the configuration and the UP or DOWN state of tracked objects, including the client (VRRP group) that is tracking an object’s state. EXEC mode or EXEC Privilege mode show track ● (Optional) Display the configuration and the UP or DOWN state of tracked interfaces and objects in VRRP groups, including the time since the last change in an object’s state.
PAGE 1087
2007::1 fe80::1 Tracking states for 2 resource Ids: 2 - Up IPv6 route, 2040::/64, priority-cost 20, 00:02:11 3 - Up IPv6 route, 2050::/64, priority-cost 30, 00:02:11 The following example shows verifying the VRRP configuration on an interface.
PAGE 1088
Sample Configurations Before you set up VRRP, review the following sample configurations. VRRP for an IPv4 Configuration The following configuration shows how to enable IPv4 VRRP. This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes.
PAGE 1089
R2(conf-if-te-2/31-vrid-99)#virtual 10.1.1.3 R2(conf-if-te-2/31-vrid-99)#no shut R2(conf-if-te-2/31)#show conf ! interface TenGigabitEthernet 2/31 ip address 10.1.1.1/24 ! vrrp-group 99 priority 200 virtual-address 10.1.1.3 no shutdown R2(conf-if-te-2/31)#end R2#show vrrp -----------------TenGigabitEthernet 2/31, VRID: 99, Net: 10.1.1.1 VRF: 0 default State: Master, Priority: 200, Master: 10.1.1.
PAGE 1090
Figure 177. VRRP for an IPv6 Configuration NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be MASTER even if one of two routers has a higher IP or IPv6 address. The following example shows configuring VRRP for IPv6 Router 2 and Router 3. Configure a virtual link local (fe80) address for each VRRPv3 group created for an interface.
PAGE 1091
vrrp-group 10 priority 100 virtual-address fe80::10 virtual-address 1::10 no shutdown R2(conf-if-te-1/1)#end R2#show vrrp -----------------TenGigabitEthernet 1/1, IPv6 VRID: 10, Version: 3, Net:fe80::201:e8ff:fe6a:c59f VRF: 0 default State: Master, Priority: 100, Master: fe80::201:e8ff:fe6a:c59f (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 135 Virtual MAC address: 00:00:5e:00:02:0a Virtual IP addre
PAGE 1092
Both Switch-1 and Switch-2 have three VRF instances defined: VRF-1, VRF-2, and VRF-3. Each VRF has a separate physical interface to a LAN switch and an upstream VPN interface to connect to the Internet. Both Switch-1 and Switch-2 use VRRP groups on each VRF instance in order that there is one MASTER and one backup router for each VRF. In VRF-1 and VRF-2, Switch-2 serves as owner-master of the VRRP group and Switch-1 serves as the backup. On VRF-3, Switch-1 is the ownermaster and Switch-2 is the backup.
PAGE 1093
% Info: The VRID used by the VRRP group 11 in VRF 2 will be 178. S1(conf-if-te-1/2-vrid-101)#priority 100 S1(conf-if-te-1/2-vrid-101)#virtual-address 10.10.1.2 S1(conf-if-te-1/2)#no shutdown ! S1(conf)#interface TenGigabitEthernet 1/3 S1(conf-if-te-1/3)#ip vrf forwarding VRF-3 S1(conf-if-te-1/3)#ip address 20.1.1.5/24 S1(conf-if-te-1/3)#vrrp-group 15 % Info: The VRID used by the VRRP group 15 in VRF 3 will be 243. S1(conf-if-te-1/3-vrid-105)#priority 255 S1(conf-if-te-1/3-vrid-105)#virtual-address 20.1.1.
PAGE 1094
VLAN Scenario In another scenario, to connect to the LAN, VRF-1, VRF-2, and VRF-3 use a single physical interface with multiple tagged VLANs (instead of separate physical interfaces). In this case, you configure three VLANs: VLAN-100, VLAN-200, and VLAN-300. Each VLAN is a member of one VRF. A physical interface (tengigabitethernet 1/1 ) attaches to the LAN and is configured as a tagged interface in VLAN-100, VLAN-200, and VLAN-300. The rest of this example is similar to the non-VLAN scenario.
PAGE 1095
Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 2 vrf2 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 419, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
PAGE 1096
Virtual MAC address: 00:00:5e:00:01:0a Virtual IP address: 20.1.1.100 Authentication: (none) DellEMC#show vrrp vrf vrf2 port-channel 1 -----------------Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 2 vrf2 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 419, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
PAGE 1097
Figure 179. VRRP for IPv6 Topology NOTE: This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. Be sure you make the necessary changes to support your own IP addresses, interfaces, names, and so on.
PAGE 1098
NOTE: The virtual IPv6 address you configure should be the same as the IPv6 subnet to which the interface belongs.
PAGE 1099
00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 DellEMC#show vrrp tengigabitethernet 2/8 TenGigabitEthernet 2/8, IPv6 VRID: 255, Version: 3, Net: fe80::201:e8ff:fe8a:e9ed VRF: 0 default State: Master, Priority: 110, Master: fe80::201:e8ff:fe8a:e9ed (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 120 Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 DellEMC# D
PAGE 1100
Proxy Gateway with VRRP VLT proxy gateway solves the inefficient traffic trombone problem when VLANs are extended between date centers and when VMs are migrated between the two DCs. Starting from Dell EMC Networking OS 9.14.0.0, VRRP provides a much simpler method to solve the traffic trombone problem. This is achieved by configuring same VRRP group IDs to the extended L3 VLANs and VRRP stays active-active across all four VLT nodes even though they are in two different VLT domains.
PAGE 1101
NOTE: The following configuration assumes that all VLT-related settings are already present on the respective devices. Sample configuration of C1: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
PAGE 1102
int ten 1/5/1 port-channel-protocol lacp port-channel 10 mode active no shut int ten 1/4/1 port-channel-protocol lacp port-channel 20 mode active no shut interface port-channel 10 vlt-peer-lag po 10 switchport no shutdown interface port-channel 20 vlt-peer-lag po 20 switchport no shutdown int vlan 100 ip address 100.1.1.2/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.254 priority 100 no shutdown int vlan 200 tagged port-channel 20 no shutdown router ospf 10 network 100.1.
PAGE 1103
int vlan 100 ip address 100.1.1.3/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.254 priority 100 no shutdown int vlan 200 tagged port-channel 20 no shutdown router ospf 10 network 100.1.1.0/24 area 0 Sample configuration of D2: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
PAGE 1104
63 Debugging and Diagnostics This chapter describes debugging and diagnostics for the device. Topics: • • • • • • • • • • Offline Diagnostics Trace Logs Auto Save on Crash or Rollover Hardware Watchdog Timer Enabling Environmental Monitoring Buffer Tuning Troubleshooting Packet Loss Enabling Application Core Dumps Mini Core Dumps Enabling TCP Dumps Offline Diagnostics The offline diagnostics test suite is useful for isolating faults and debugging hardware.
PAGE 1105
NOTE: The system reboots when the offline diagnostics complete. This is an automatic process. The following warning message appears when you implement the offline stack-unit command: Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y After the system goes offline, you must reload or run the online stack-unit stack-unit-number command for the normal operation. 2. Confirm the offline status.
PAGE 1106
--------------------------------------------------------------------------0 0 up AC up 18048 0 1 absent absent 0 -- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed -----------------------------------------------------------------------------------0 0 up up 19275 up 19275 0 1 up up 19275 up 19275 0 2 absent Speed in RPM The following example shows the diag command (standalone unit).
PAGE 1107
**************************** S6000 LEVEL 0 DIAGNOSTICS************************** Test 1 - Board Revision Test ........................................ PASS Test 2 - Cpu Type Detect Test ....................................... PASS Test 3.000 - Psu0 Presence Test ..................................... PASS diagS6000PsuPresenceTest[1022]: ERROR: Psu:1 is not present... Test 3.001 - Psu1 Presence Test ..................................... NOT PRESENT Test 3 - Psu Presence Test ..................................
PAGE 1108
I2C Devices Scanned - 20 I2C Device PASS Count - 17 I2C Device FAIL Count - 3 Test 13 - I2c Access Test ........................................... Test 14 - RTC Presence Test ......................................... Test 15 - CPU Sdram Presence Test ................................... Test 16 - CPU Sdram Size Test ...................................... Test 17.000 - System Cpld Access Test ............................... Test 17.001 - Master Cpld Access Test ............................... Test 17.
PAGE 1109
QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 52 52 52 52 52 52 52 52 52 52 52 52 Length(OM2) 1m = 0x00 Length(OM1) 1m = 0x00 Length(Copper) 1m = 0x00 Vendor Rev = 01 Laser Wavelength = 850.
PAGE 1110
-- Temperature Limits (deg C) ----------------------------------------------------------------Minor Off Minor Major Off Major Shutdown Unit2 55 60 75 80 85 ---------------------------------------------------------------Minor Off Minor Major Off Major Shutdown Unit3 55 60 75 80 85 Troubleshoot an Over-temperature Condition To troubleshoot an over-temperature condition, use the following information. 1. Use the show environment commands to monitor the temperature levels. 2. Check air flow through the system.
PAGE 1111
Table 143. SNMP Traps and OIDs (continued) OID String OID Name Description .1.3.6.1.4.1.6027.3.27.1.4 dellNetFpPacketBufferTable View the modular packet buffers details per stack unit and the mode of allocation. .1.3.6.1.4.1.6027.3.27.1.5 dellNetFpStatsPerPortTable View the forwarding plane statistics containing the packet buffer usage per port per stack unit. .1.3.6.1.4.1.6027.3.27.1.
PAGE 1112
● show hardware {ip | ipv6 | mac} {eg-acl | in-acl} stack-unit stack-unit-number port-set 0 pipeline 0-3 ● show hardware ip qos stack-unit stack-unit-number port-set 0 ● show hardware system-flow layer2 stack-unit stack-unit-number port-set 0 {counters | pipeline 0-3} ● show hardware drops interface interface ● show hardware buffer-stats-snapshot resource interface interface ● show hardware buffer inteface interface{priority-group { id | all } | queue { id| all} } buffer-info ● show hardware buffer-stats-sn
PAGE 1113
Port bitmap zero Drops Rx VLAN Drops --- Ingress MAC counters--Ingress FCSDrops Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS on COS10 HOL DROPS on COS11 HOL DROPS on COS12 HOL DROPS on COS13 HOL DROPS on COS14 HOL DROPS on COS15 HOL DROPS on COS16 HOL DROPS on COS17 TxPurge CellErr Aged Drops ---
PAGE 1114
rxPkt(COS2 ) :0 rxPkt(COS3 ) :0 rxPkt(COS4 ) :0 rxPkt(COS5 ) :0 rxPkt(COS6 ) :0 rxPkt(COS7 ) :0 rxPkt(COS8 ) :773 rxPkt(COS9 ) :0 rxPkt(COS10) :0 rxPkt(COS11) :0 rxPkt(UNIT0) :773 transmitted :12698 txRequested :12698 noTxDesc :0 txError :0 txReqTooLarge :0 txInternalError :0 txDatapathErr :0 txPkt(COS0 ) :0 txPkt(COS1 ) :0 txPkt(COS2 ) :0 txPkt(COS3 ) :0 txPkt(COS4 ) :0 txPkt(COS5 ) :0 txPkt(COS6 ) :0 txPkt(COS7 ) :0 txPkt(COS8 ) :0 txPkt(COS9 ) :0 txPkt(COS10) :0 txPkt(COS11) :0 txPkt(UNIT0) :0 Example of
PAGE 1115
Display Stack Member Counters You can use the show hardware command to display internal receive and transmit statistics, based on the selected command option. The following example is a sample of the output for the counters option.
PAGE 1116
RX - IPV6 L3 Unicast Frame Counter --------------------Interface Fo 0/60 : Description RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Frame Counter RX - IPV6 L3 routed multicast Packets RX - Unicast Packet Counter RX - 64 Byte Frame Counter RX - 64 to 127 Byte Frame Counter RX - 128 to 255 Byte Frame Counter RX - 256 to 511 Byte Frame Counter RX - 512 to 1023 Byte Frame Counter RX - 1024 to 1518 Byte Frame Counter RX - 1519 to 1522 Byte Good VLAN Frame Counter
PAGE 1117
RX - Unicast Packet Counter RX - 64 Byte Frame Counter RX - 65 to 127 Byte Frame Counter RX - 128 to 255 Byte Frame Counter RX - 256 to 511 Byte Frame Counter RX - 512 to 1023 Byte Frame Counter RX - 1024 to 1518 Byte Frame Counter RX - 1519 to 1522 Byte Good VLAN Frame Counter RX - 1519 to 2047 Byte Frame Counter RX - 2048 to 4095 Byte Frame Counter RX - 4096 to 9216 Byte Frame Counter RX - Good Packet Counter RX - Packet/Frame Counter RX - Unicast Frame Counter RX - Multicast Frame Counter RX - Broadcast
PAGE 1118
A mini core dump contains critical information in the event of a crash. Mini core dump files are located in flash:/ (root dir). The application mini core filename format is f10StkUnit..acore.mini.txt. The kernel mini core filename format is f10StkUnit.kcore.mini.txt. The following are sample filenames. When a member or standby unit crashes, the mini core file gets uploaded to master unit.
PAGE 1119
You can use the capture-duration timer and the packet-count counter at the same time. The TCP dump stops when the first of the thresholds is met. That means that even if the duration timer is 9000 seconds, if the maximum file count parameter is met first, the dumps stop. To enable a TCP dump, use the following command. ● Enable a TCP dump for CPU bound traffic.
PAGE 1120
64 Standards Compliance This chapter describes standards compliance for Dell EMC Networking products. NOTE: Unless noted, when a standard cited here is listed as supported by the Dell EMC Networking OS, the system also supports predecessor standards. One way to search for predecessor standards is to use the http://tools.ietf.org/ website. Click “Browse and search IETF documents,” enter an RFC number, and inspect the top of the resulting document for obsolescence citations to related RFCs.
PAGE 1121
RFC and I-D Compliance Dell EMC Networking OS supports the following standards. The standards are grouped by related protocol. The columns showing support by platform indicate which version of Dell EMC Networking OS first supports the standard. General Internet Protocols The following table lists the Dell EMC Networking OS support per platform for general internet protocols. Table 144.
PAGE 1122
Table 144. General Internet Protocols (continued) R F C # Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 6 0 Transfer Protocol 2 4 7 4 Definition of 7.7.1 the Differentiate d Services Field (DS Field) in the IPv4 and IPv6 Headers 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2 PPP over 61 SONET/SD 5 H 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2 6 9 8 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.
PAGE 1123
Table 145. General IPv4 Protocols (continued) RF C# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 103 DOMAIN NAMES 5 IMPLEMENTATION AND SPECIFICATION (client) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 104 A Standard for the 2 Transmission of IP Datagrams over IEEE 802 Networks 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 1191 Path MTU Discovery 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.
PAGE 1124
Table 146. General IPv6 Protocols (continued) RFC Full Name # S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 246 2 (Par tial) IPv6 Stateless Address Autoconfiguration 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 246 4 Transmission of IPv6 Packets over Ethernet Networks 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 267 5 IPv6 Jumbograms 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2711 IPv6 Router Alert Option 8.3.12.0 9.8(0.
PAGE 1125
Table 147. Border Gateway Protocol (BGP) (continued) RFC# Full Name SSeries/ZSeries S3048–ON S4048–ON Z9100–ON S4048TON S6010–ON 2842 Capabilities Advertisement with BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2858 Multiprotocol Extensions for BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2918 Route Refresh Capability for BGP-4 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 3065 Autonomous System Confederations for BGP 7.8.1 9.
PAGE 1126
Intermediate System to Intermediate System (IS-IS) The following table lists the Dell EMC Networking OS support per platform for IS-IS protocol. Table 149. Intermediate System to Intermediate System (IS-IS) RFC# Full Name S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1142 OSI IS-IS Intra-Domain Routing Protocol (ISO DP 10589) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 1195 Use of OSI IS-IS for Routing in TCP/IP and Dual Environments 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.
PAGE 1127
Routing Information Protocol (RIP) The following table lists the Dell EMC Networking OS support per platform for RIP protocol. Table 150. Routing Information Protocol (RIP) RF C# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 105 8 Routing Information Protocol 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 245 RIP Version 3 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 4191 Default Router Preferences and More-Specific Routes 8.3.12.0 9.8(0.
PAGE 1128
Table 152. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1156 Management Information Base for Network Management of TCP/IP-based internets 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 1157 A Simple Network Management 7.6.1 Protocol (SNMP) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 1212 Concise MIB Definitions 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.
PAGE 1129
Table 152. Network Management (continued) RFC# Full Name 2575 S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON View-based Access Control 7.6.1 Model (VACM) for the Simple Network Management Protocol (SNMP) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 2576 Coexistence Between Version 1, 7.6.1 Version 2, and Version 3 of the Internet-standard Network Management Framework 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 2578 Structure of Management Information Version 2 (SMIv2) 7.
PAGE 1130
Table 152. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON Network Management Protocol (SNMP) 3418 Management Information Base (MIB) for the Simple Network Management Protocol (SNMP) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 3434 Remote Monitoring MIB Extensions for High Capacity Alarms, High-Capacity Alarm Table (64 bits) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 3580 IEEE 802.
PAGE 1131
Table 152. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON IEEE Management Information Base 7.7.1 802.1A module for LLDP configuration, B statistics, local system data and remote systems data components. 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) IEEE The LLDP Management 802.1A Information Base extension B module for IEEE 802.1 organizationally defined discovery information. (LLDP DOT1 MIB and LLDP DOT3 MIB) 7.7.1 9.8(0.0P2) 9.8(0.
PAGE 1132
Table 152. Network Management (continued) RFC# Full Name FORC E10-IFEXTEN SIONMIB S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON Force10 Enterprise IF Extension 7.6.1 MIB (extends the Interfaces portion of the MIB-2 (RFC 1213) by providing proprietary SNMP OIDs for other counters displayed in the "show interfaces" output) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) FORC E10LINKA GGMIB Force10 Enterprise Link Aggregation MIB 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.
PAGE 1133
Table 152. Network Management (continued) RFC# Full Name S4810 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON ALAR M-MIB MIB Location You can find Force10 MIBs under the Force10 MIBs subhead on the Documentation page of iSupport: https://www.force10networks.com/CSPortal20/KnowledgeBase/Documentation.aspx You also can obtain a list of selected MIBs and their OIDs at the following URL: https://www.force10networks.com/CSPortal20/Main/Login.aspx Some pages of iSupport require a login.
PAGE 1134
65 X.509v3 supports X.509v3 standards. Topics: • • • • • • • • • Introduction to X.509v3 certificates X.509v3 support in Information about installing CA certificates Information about Creating Certificate Signing Requests (CSR) Information about installing trusted certificates Transport layer security (TLS) Online Certificate Status Protocol (OSCP) Verifying certificates Event logging Introduction to X.509v3 certificates X.
PAGE 1135
Advantages of X.509v3 certificates Public key authentication is preferred over password-based authentication, although both may be used in conjunction, for various reasons. Public-key authentication provides the following advantages over normal password-based authentication: ● Public-key authentication avoids the human problems of low-entropy password selection and provides more resistance to brute-force attacks than password-based authentication.
PAGE 1136
The other hosts on the network, such as the SUT switch, syslog server, and OCSP server, generate private keys and create Certificate Signing Requests (CSRs). The hosts then upload the CSRs to the Intermediate CA or make the CSRs available for the Intermediate CA to download. generates a CSR using the crypto cert generate request command. The hosts on the network (SUT, syslog, OCSP…) also download and install the CA certificates from the Root and Intermediate CAs.
PAGE 1137
After the CA certificate is installed, the system can secure communications with TLS servers by verifying certificates that are signed by the CA. Installing CA certificate To install a CA certificate, enter the crypto ca-cert install {path} command in Global Configuration mode. Information about Creating Certificate Signing Requests (CSR) Certificate Signing Request (CSR) enables a device to get a X.509v3 certificate from a CA. In order for a device to get a X.
PAGE 1138
● ● ● ● ● ● Organization Unit Name Common Name Email address Validity Length Alternate Name NOTE: The command contains multiple options with the Common Name being a required field and blanks being filled in for unspecified fields. Information about installing trusted certificates Dell EMC Networking OS also enables you to install a trusted certificate. The system can then present this certificate for authentication to clients such as SSH and HTTPS.
PAGE 1139
When not operating in FIPS mode, the system may support TLS 1.0 up to 1.2, and older ciphers and hashes: TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA TLS_DHE_RSA_WITH_AES_256_CBC_SHA TLS_DHE_RSA_WITH_AES_128_CBC_SHA TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_ECDH_RSA_WITH_AES_256_CBC_SHA TLS_ECDH_RSA_WITH_AES_128_CBC_SHA TLS_DH_RSA_WITH_AES_256_CBC_SHA TLS_DH_RSA_WITH_AES_128_CBC_SHA TLS compression is disabled by default.
PAGE 1140
Configuring OCSP behavior You can configure how the OCSP requests and responses are signed when the CA or the device contacts the OCSP responders. To configure this behavior, follow this step: In CONFIGURATION mode, enter the following command: crypto x509 ocsp {[nonce] [sign-request]} Both the none and sign-request parameters are optional. The default behavior is to not use these two options.
PAGE 1141
Verifying Client Certificates Verifying client certificates is optional in the TLS protocol and is not explicitly required by Common Criteria. However, TLS-protected Syslog and RADIUS protocols mandate that certificate-based mutual authentication be performed. Event logging The system logs the following events: ● ● ● ● ● A CA certificate is installed or deleted. A self-signed certificate and private key are generated. An existing host certificate, a private key, or both are deleted.