Administrator Guide

Table 121. Interface level MIB Objects for Port Security
MIB Object OID Access or Permission Description
dellNetPortSecIfPortSecurity
Enable
1.3.6.1.4.1.6027.3.31.1.2.1.1.1 read-only Specifies if the port security feature
is enabled or disabled on an
interface.
dellNetPortSecIfPortSecurity
Status
1.3.6.1.4.1.6027.3.31.1.2.1.1.2 read-only Represents the port security status
of an interface.
dellNetPortSecIfSecureMacLi
mit
1.3.6.1.4.1.6027.3.31.1.2.1.1.3 read-write Maximum number (N) of MAC
addresses to be secured on the
interface
dellNetPortSecIfCurrentMacC
ount
1.3.6.1.4.1.6027.3.31.1.2.1.1.4 read-only Current number of MAC addresses
learnt or configured on this interface
dellNetPortSecIfStationMove
Enable
1.3.6.1.4.1.6027.3.31.1.2.1.1.5 read-write Enable or disable station movement
on the dynamically secured MAC
addresses learnt on the interface.
dellNetPortSecIfSecureMacVi
olationAction
1.3.6.1.4.1.6027.3.31.1.2.1.1.6 read-write Determines the action to be taken
when MAC limit violation occurs in
the system.
dellNetPortSecIfStmvViolatio
nAction
1.3.6.1.4.1.6027.3.31.1.2.1.1.7 read-write Determines the action to be taken
when either dynamic or static MAC
limit violation occurs in the system.
dellNetPortSecIfStickyEnable 1.3.6.1.4.1.6027.3.31.1.2.1.1.8 read-write Enables or disables sticky port
security feature on this interface.
dellNetPortSecIfClearSecure
MacAddresses
1.3.6.1.4.1.6027.3.31.1.2.1.1.9 read-write Deletes secure MAC addresses
based on the specified type.
dellNetPortSecIfResetViolatio
nStatus
1.3.6.1.4.1.6027.3.31.1.2.1.1.10 read-write Resets the violation status of an
interface based on the specified
type.
dellNetPortSecIfSecureMacA
geEnable
1.3.6.1.4.1.6027.3.31.1.2.1.1.11 read-write Enables aging of the dynamically
secured MAC addresses learnt on
the interface.
Enabling and viewing SNMP for port security
To enable or view DELL-NETWORKING-PORT-SECURITY-MIB, configure snmp-server in read-write mode using the snmp-
server community public rw command. You can enable the port security feature on the Dell EMC Networking OS using
the snmpset command. Also, you can view if the port security feature is enabled or disabled using the snmpwalk command.
To configure dellNetPortSecIfSecureMacLimit as 100 on an interface whose ifIndex is 2101252, use the following
command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 100
To remove dellNetPortSecIfSecureMacLimit configuration on an interface whose ifIndex is 2101252, use the
following command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 2147483647
To retrieve dellNetPortSecIfSecureMacLimit configured on an interface whose ifIndex is 2101252, use the following
command.
snmpwalk -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252
SNMPv2-SMI::enterprises.6027.3.31.1.2.1.1.3. 2101252 = INTEGER: 10
928
Simple Network Management Protocol (SNMP)