API Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Table Of Contents

Dell EMC Command Line Reference Guide for

the S3100 Series

9.14.2.2

July 2019

Rev. A00

Summary of content (1690 pages)

PAGE 1
Dell EMC Command Line Reference Guide for the S3100 Series 9.14.2.2 July 2019 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide.........................................................................................................40 Objectives........................................................................................................................................................................... 40 Audience..............................................................................................................................................................................
PAGE 4
cam-acl................................................................................................................................................................................ 88 cam-acl-vlan....................................................................................................................................................................... 89 clear average-power...........................................................................................................................
PAGE 5
show system..................................................................................................................................................................... 143 show tech-support.......................................................................................................................................................... 145 ssh-peer-stack-unit........................................................................................................................................
PAGE 6
Standard IP ACL Commands........................................................................................................................................ 190 deny...............................................................................................................................................................................190 ip access-list standard.............................................................................................................................................
PAGE 7
match route-type...................................................................................................................................................... 247 match tag....................................................................................................................................................................248 route-map...........................................................................................................................................................
PAGE 8
deny deny deny deny udp (for IPv6 ACLs).............................................................................................................................................303 tcp (for IPv6 ACLs)............................................................................................................................................. 305 icmp (for Extended IPv6 ACLs)........................................................................................................................
PAGE 9
bgp confederation peers......................................................................................................................................... 348 bgp connection-retry-timer....................................................................................................................................349 bgp dampening..........................................................................................................................................................
PAGE 10
neighbor route-reflector-client..............................................................................................................................394 neighbor sender-side-loopdetect.......................................................................................................................... 395 neighbor send-community...................................................................................................................................... 395 neighbor shutdown..............
PAGE 11
show ip extcommunity-list......................................................................................................................................450 IPv6 BGP Commands..................................................................................................................................................... 451 clear ip bgp ipv6 unicast soft..................................................................................................................................
PAGE 12
show show show show hardware hardware hardware hardware stack-unit buffer-stats-snapshot (Total Buffer Information).......................................... 493 system-flow.................................................................................................................................. 495 vlan-counters................................................................................................................................497 drops....................................................
PAGE 13
ipv6 dhcp snooping verify mac-address..............................................................................................................530 ip helper-address....................................................................................................................................................... 531 ipv6 helper-address...................................................................................................................................................
PAGE 14
show garp timers............................................................................................................................................................. 571 show gvrp......................................................................................................................................................................... 572 show gvrp statistics...................................................................................................................................
PAGE 15
errdisable recovery cause........................................................................................................................................ 614 errdisable recovery interval..................................................................................................................................... 615 flowcontrol..................................................................................................................................................................
PAGE 16
channel-member........................................................................................................................................................678 group............................................................................................................................................................................ 680 interface port-channel..........................................................................................................................................
PAGE 17
ip helper-address.............................................................................................................................................................722 ip helper-address hop-count disable.......................................................................................................................... 723 ip host.....................................................................................................................................................................
PAGE 18
ipv6 address eui64.......................................................................................................................................................... 779 ipv6 control-plane icmp error-rate-limit.................................................................................................................... 779 ipv6 flowlabel-zero.........................................................................................................................................................
PAGE 19
distribute-list in................................................................................................................................................................ 819 distribute-list out.............................................................................................................................................................820 distribute-list redistributed-override...............................................................................................................
PAGE 20
spf-interval....................................................................................................................................................................... 866 Chapter 28: Link Aggregation Control Protocol (LACP)............................................................. 868 clear lacp counters......................................................................................................................................................... 868 debug lacp.......................
PAGE 21
Chapter 30: Link Layer Discovery Protocol (LLDP).................................................................... 909 LLPD Commands............................................................................................................................................................ 909 advertise dot1-tlv...................................................................................................................................................... 909 advertise dot3-tlv..........................
PAGE 22
ip msdp peer.....................................................................................................................................................................946 ip msdp redistribute........................................................................................................................................................948 ip msdp sa-filter..........................................................................................................................................
PAGE 23
Chapter 35: Multicast............................................................................................................... 980 IPv4 Multicast Commands............................................................................................................................................980 clear ip mroute...........................................................................................................................................................980 ip mroute.........................
PAGE 24
track interface ip routing........................................................................................................................................1017 track interface line-protocol.................................................................................................................................. 1017 track ip host reachability........................................................................................................................................
PAGE 25
passive-interface.....................................................................................................................................................1060 redistribute................................................................................................................................................................1062 redistribute bgp....................................................................................................................................................
PAGE 26
maximum-paths......................................................................................................................................................... 1121 passive-interface...................................................................................................................................................... 1122 redistribute...........................................................................................................................................................
PAGE 27
show ip pim ssm-range........................................................................................................................................... 1170 show ip pim summary............................................................................................................................................... 1171 show ip pim tib..........................................................................................................................................................
PAGE 28
private-vlan mapping secondary-vlan.......................................................................................................................1207 switchport mode private-vlan.................................................................................................................................... 1208 Chapter 44: Per-VLAN Spanning Tree Plus (PVST+)................................................................. 1210 description..........................................................
PAGE 29
service-queue............................................................................................................................................................1251 set............................................................................................................................................................................... 1252 show qos class-map........................................................................................................................................
PAGE 30
show running-config rip...............................................................................................................................................1298 timers basic.....................................................................................................................................................................1299 version........................................................................................................................................................
PAGE 31
service obscure-passwords................................................................................................................................... 1341 Authentication and Password Commands...............................................................................................................1342 aaa authentication enable......................................................................................................................................1342 aaa authentication login..........
PAGE 32
tacacs-server key.................................................................................................................................................... 1380 tacacs-server vrf......................................................................................................................................................1381 Port Authentication (802.1X) Commands...............................................................................................................
PAGE 33
ip dhcp snooping database....................................................................................................................................1422 ip dhcp snooping database renew....................................................................................................................... 1423 ip dhcp snooping trust............................................................................................................................................
PAGE 34
show snmp user....................................................................................................................................................... 1458 snmp context............................................................................................................................................................1459 snmp ifmib ifalias long............................................................................................................................................
PAGE 35
disable.............................................................................................................................................................................. 1523 forward-delay................................................................................................................................................................. 1524 hello-time.......................................................................................................................................
PAGE 36
address....................................................................................................................................................................... 1561 street-address..........................................................................................................................................................1562 territory......................................................................................................................................................
PAGE 37
clear ufd-disable............................................................................................................................................................ 1598 debug uplink-state-group............................................................................................................................................1599 description.........................................................................................................................................................
PAGE 38
clear vlt statistics.......................................................................................................................................................... 1637 delay-restore.................................................................................................................................................................. 1638 delay-restore abort-threshold..........................................................................................................................
PAGE 39
Chapter 67: X.509v3................................................................................................................ 1680 crypto ca-cert delete................................................................................................................................................... 1680 crypto ca-cert install..................................................................................................................................................... 1681 crypto cert delete......
PAGE 40
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 41
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 42
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 43
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/1 for the interface tengigabitethernet 1/1/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
PAGE 44
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
PAGE 45
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
PAGE 46
Usage Information Activate the VRF application on a device using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any platform. show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific.
PAGE 47
CLASS-MAP Mode To create or configure a class map, use CLASS-MAP mode. For more information, see Policy-Based QoS Commands. To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command.
PAGE 48
2. Enter the ecmp-group command then enter the ECMP group ID. The prompt changes to include conf-ecmp-groupecmp-group-id. You can return to CONFIGURATION mode by using the exit command. EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command.
PAGE 49
To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port number.
PAGE 50
LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information, see Link Layer Discovery Protocol (LLDP). To enter LLDP mode: 1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode. 2. Enter the protocol lldp command. The prompt changes to include conf-lldp or conf-if-interface-lldp.
PAGE 51
2. Enter the protocol spanning-tree mstp command. The prompt changes to include conf-mstp. You can return to CONFIGURATION mode by using the exit command. OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the openflow of-instance command, and then the OpenFlow ID number of the instance you want to create or configure.
PAGE 52
RAPID SPANNING TREE (RSTP) Mode To enable and configure RSTP, use RSTP mode. For more information, see Rapid Spanning Tree Protocol (RSTP). To enter RSTP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree rstp command. The prompt changes to include conf-rstp. You can return to CONFIGURATION mode by using the exit command. ROUTE-MAP Mode To configure a route map, use ROUTE-MAP mode. To enter ROUTE-MAP mode: 1.
PAGE 53
You can return to CONFIGURATION mode by using the exit command. ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, see Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include conf-router_rip. You can return to CONFIGURATION mode by using the exit command.
PAGE 54
2. Enter the vrrp-group command, and then enter the VRRP group ID. The prompt changes to include conf-ifinterface-type-slot/port-vrid-vrrp-group-id.
PAGE 55
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 56
secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. system: Enter the keyword system: to use the system image file URL (system). ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system. nfsmount://filepath system: Enter the keyword system: to retrieve the image from the system.
PAGE 57
Parameters flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB. directory name and path Enter the directory name and path as follows: directory name ([[flash://]directory_path]) NOTE: The cd command without any arguments will change the current directory to flash: Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 58
running-config Enter the keywords running-config to copy from the current system configuration. scp: Enter the keyword scp: to copy from the remote file system, IPv4, or IPv6, (scp://userid:password@hostip/filepath). startup-config Enter the keywords startup-config to copy from the startup configuration. tftp: Enter the keyword tftp: to copy from the remote file system, IPv4, or IPv6, (tftp://hostip/filepath). usbflash: Enter the keyword usbflash: to copy the file to or from the external USB flash.
PAGE 59
When you load the startup configuration or a configuration file from a network server such as TFTP to the running configuration, the configuration is added to the running configuration. This does not replace the existing running configuration. Commands in the configuration file has precedence over commands in the running configuration. Dell EMC Networking OS supports copying the running-configuration to a TFTP server, an FTP server, or a remote NFS file system.
PAGE 60
Related Commands ● cd – changes the working directory. delete Delete a file from the flash. After deletion, files cannot be restored. Syntax delete {flash: | nfsmount: | usbflash:} [no-confirm] Parameters flash: To delete a file or directory on the internal flash, enter flash:// then the filename or directory name ([flash://]filepath). nfsmount: To delete a file or directory on the NFS-mounted file system, enter nfsmount:// then the mount point and the file path (nfsmount://filepath).
PAGE 61
Parameters flash: For a directory on the internal Flash, enter flash:// directory name. nfsmount: For a file or directory on an NFS-mounted file system, enter nfsmount:// then the mount point and file path. NOTE: While displaying a file directory on a remote NFS file system, it is mandatory to specify the mount-point that indicates the working directory on the NFS file system. You cannot display details corresponding to the root directory of the remote NFS file system.
PAGE 62
nfsmount: 1463410688 bytes total (585719808 bytes free) DellEMC# Related Commands ● cd — changes the working directory. format Erase all existing files and reformat the file system. After the file system is formatted, files cannot be restored. Syntax format {flash: | usbflash:} Defaults None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 63
usbflash: Defaults For a directory on the external USB flash, enter usbflash:// directory name. None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 64
Example Related Commands Version Description 9.7(0.0) Introduced on the S-Series. DellEMC# mkdir nfsmount:/nfs-mountpoint/guest DellEMC# ● rmdir — remove a directory. mount nfs Mounts an NFS file system to a device. Syntax mount nfs rhost:path mount-point [username password] Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system.
PAGE 65
Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 66
Defaults none Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Enhanced to specify the MD5, SHA1, or SHA256 hash of the OS image that the system uses to validate the image during reboot. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.
PAGE 67
○ hardware forwarding-table mode {scaled-l2-switch | scaled-l3-routes | scaled-l3-hosts} ○ cam-ipv6 extended-prefix {1024 | 2048 | 3072} ○ ip ecmp-group maximum-paths 2-64 ● ACL CAM carving related CLIs: ○ cam-acl cli ○ cam-acl-vlan cli ○ cam-acl-egress cli ○ cam-sharing ● Feature keyword CLIs: ○ feature udf-acl ○ feature aclrange ○ feature ipv6acloptimized ○ feature acloptimized Example DellEMC# upgrade system tftp://10.11.8.12/dv-rainier-13 a: 00:39:32 : Discarded 1 pkts. Expected block num : 51.
PAGE 68
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.
PAGE 69
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fan-out, and so forth). When restoring all units in a stack, all the units in the stack are placed into stand-alone mode.
PAGE 70
Example (single stack) Example (NvRAM all stack units) Example (NvRAM, single unit) DellEMC# restore factory-defaults stack-unit 1 clear-all ************************************************************** * Warning - Restoring factory defaults will delete the existing * * startup-config and all persistent settings (stacking, fanout, etc.)* * After restoration the unit(s) will be powercycled immediately.
PAGE 71
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 72
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. E-Series Original command. DellEMC# show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 73
Example Version Description 7.6.1.0 Introduced on the S-Series 7.5.1.
PAGE 74
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 75
show running-config Display the current configuration and display changes from the default values. Syntax Parameters show running-config [entity] [configured] [status] [compressed] entity (OPTIONAL) To display that entity’s current (non-default) configuration, enter one of the following keywords: NOTE: If you did not configure anything that entity, nothing displays and the prompt returns.
PAGE 76
File Management mac for the current MAC ACL configuration mac-addresstable for the current MAC configuration managementeis for the current management EIS configuration managementroute for the current Management port forwarding configuration mld for the current MLD configuration monitor for the current Monitor configuration mroute for the current Mroutes configuration msdp for the current MSDP configuration ntp for the current NTP configuration ospf for the current OSPF configuration
PAGE 77
uplink-stategroup for the uplink state group configuration users for the current users configuration vlt for the current VLT configuration wred-profile for the current wred-profile configuration configured (OPTIONAL) Enter the keyword configuration to display line card interfaces with non-default configurations only. status (OPTIONAL) Enter the keyword status to display the checksum for the running configuration and the start-up configuration.
PAGE 78
boot system gateway 10.16.132.
PAGE 79
Example Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to include the last configuration change, start-up last updated (date and time), and who made the change. DellEMC#show startup-config ! Version 1-0(0-4781) ! Startup-config last updated at Sun Mar 20 18:28:22 2016 by default ! boot system stack-unit 1 primary system: A: boot system stack-unit 1 secondary system: A: boot system stack-unit 1 default system: A: boot system gateway 10.16.132.
PAGE 80
Command Fields Example (S3100) Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series 7.5.1.0 Introduced on the C-Series. E-Series Original command. Lines Beginning With Description Dell EMC Network... Name of the operating system Dell EMC Operating... OS version number Dell EMC Application...
PAGE 81
96 GigabitEthernet/IEEE 802.3 interface(s) 6 Ten GigabitEthernet/IEEE 802.3 interface(s) upgrade Upgrade the bootflash image or system image of the management unit. Syntax Parameters upgrade boot {all | bootflash—image | bootselector-image} stack-unit {stackunit-number | all} {booted | flash: | ftp: | nfsmount | scp: | tftp: | usbflash:} file-url boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image.
PAGE 82
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0(0.0) Added support for IPv6 for the file-url parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series.
PAGE 83
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
PAGE 84
• • • • • • • • • • • • • • • • • • show inventory show login statistics show memory show processes cpu show processes ipc flow-control show processes memory show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit telnet telnet-peer-stack-unit terminal length traceroute undebug all virtual-ip write banner exec Configure a message that is displayed when your enter EXEC mode. Syntax banner exec c line c To delete a banner, use the no banner exec command.
PAGE 85
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original Command After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
PAGE 86
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the acknowledgement keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 87
banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters Defaults c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator. The delineator is a percent character (%). No banner is configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 88
cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 89
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dual-qos. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. For the new settings to take effect, save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system.
PAGE 90
clear average-power Reset the average power and average power start time. Syntax clear average-power stack-unit {stack-unit-number} Parameters Defaults stack-unitnumber Enter the stack unit number. None Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 91
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode.
PAGE 92
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode. Syntax disable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of the Dell EMC Networking OS. The range is from 0 to 15.
PAGE 93
Version Description E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax Parameters Defaults do command command Enter an EXEC-level command. none Command Modes ● CONFIGURATION ● INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 94
System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n DellEMC(conf-if-gi-5/1)# enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Syntax enable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of Dell EMC Networking OS. The range is from 0 to 15. 15 Command Modes EXEC Command History This guide is platform-specific.
PAGE 95
enable optic-info-update interval Enable polling intervals of optical information updates for simple network management protocol (SNMP). Syntax enable optic-info-update [interval seconds] To disable optical power information updates, use the no enable optic-info-update interval command. Parameters Defaults interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds. The default is 300 seconds (5 minutes).
PAGE 96
● ● ● ● ● ● Command History Related Commands AS-PATH ACL COMMUNITY-LIST ROUTER OSPF ROUTER RIP ROUTER ISIS ROUTER BGP This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.
PAGE 97
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 98
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 99
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. morpheus% ftp 10.31.1.111 Connected to 10.31.1.111. 220 DellEMC(1.
PAGE 100
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 101
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 102
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The hostname is used in the prompt. ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command.
PAGE 103
Version Description 7.5.1.0 Introduced on C-Series ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 104
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 105
● For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.10(0.
PAGE 106
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 107
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Use this command to make the FTP clients VRF-aware. The VRF name that you specify is used by the FTP client to reach the FTP server. If no VRF name is specified, then the default VRF is used. ip telnet server enable Enable the Telnet server on the switch.
PAGE 108
To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters Defaults vrf-name Enter the vrf-name to specify the VRF that is used by the TELNET server. any Enter the keyword any to enable server from any VRF. management Enter the keyword management to specify a management VRF that is used by the TELNET server. Disabled Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 109
● For VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 110
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant FTOS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 111
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards. 8.2.1.0 Increased number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server.
PAGE 112
line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. Syntax line {aux 0 |console 0 | vty number [end-number]} Parameters Defaults aux 0 Enter the keyword aux 0 to configure the auxiliary terminal connection. console 0 Enter the keyword console 0 to configure the console port. The console option is <0-0>.
PAGE 113
login concurrent-session Configures the limit of concurrent sessions for each user on console and virtual terminal lines. Syntax login concurrent-session {limit number-of-sessions | clear—line enable} no login concurrent-session {limit number-of-sessions | clear—line enable} Parameters Defaults limit number-of- sessions Sets the number of concurrent sessions that any user can have on console and virtual terminal lines. The range is from 1 to 12 (10 VTY lines, one console, and one AUX line).
PAGE 114
Escape character is '^]'. Login: admin Password: Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.97 Clear existing session? [line number/Enter to cancel]: When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of your existing sessions. Close any of your existing sessions to log in to the system. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'.
PAGE 115
Usage Information Version Description 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. Only the system and security administrators can configure login activity tracking and view the login activity details of other users. If you enable user login statistics, the system displays the last successful login details of the current user, the details of any failed login attempts by others, and if the current user’s permissions have changed since the last login.
PAGE 116
motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 117
NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults count Enter the number of echo packets to be sent. The default is 5. ● number: from 1 to 2147483647 ● continuous: transmit echo request continuously datagram size Enter the ICMP datagram size. The range is from 36 to 15360 bytes. The default is 100. timeout Enter the interval to wait for an echo reply before timing out. The range is from 0 to 3600 seconds. The default is 2 seconds.
PAGE 118
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0)P5 Introduced on the S4048–ON. 9.8(0.
PAGE 119
Example (IPv4) Symbol Description ? Unknown packet type. & Packet lifetime exceeded. DellEMC# ping 172.31.1.255 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2 seconds: Reply to request 1 from 172.31.1.208 0 ms Reply to request 1 from 172.31.1.216 0 ms Reply to request 1 from 172.31.1.205 16 ms :: Reply to request 5 from 172.31.1.209 0 ms Reply to request 5 from 172.31.1.66 0 ms Reply to request 5 from 172.31.1.
PAGE 120
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 9.1(0.0) Added ‘conditional’ parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you use only the reload command, the system boots into the Dell EMC Networking OS.
PAGE 121
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series.
PAGE 122
Usage Information Version Description 9.14(1.5) Added support for UTC time format. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 123
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.
PAGE 124
Example DellEMC#show cam-acl-vlan -- Chassis Vlan Cam ACL -Current Settings(in block sizes) 1 block = 256 entries VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 -- stack-unit 1 -Current Settings(in block sizes) VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 show command-history Display a buffered log of all commands all users enter along with a time stamp.
PAGE 125
Example Example 1: Default configuration service timestamps log datetime or service timestamps log datetime localtime DellEMC#show clock 15:42:42.804 IST Fri May 17 2019 DellEMC(conf)#service timestamps log datetime DellEMC#show command-history [May 17 15:38:55]: CMD-(CLI):[service timestamps log datetime]by default from console [May 17 15:41:40]: CMD-(CLI):[write memory]by default from console - Repeated 1 time.
PAGE 126
[May 17 [May 17 [May 17 [May 17 [May 17 console 15:54:54]: 15:55:00]: 15:55:12]: 15:55:22]: 15:55:27]: CMD-(CLI):[end]by default from console CMD-(CLI):[show logging]by default from console CMD-(CLI):[show clock]by default from console CMD-(CLI):[show running-config]by default from console CMD-(CLI):[show command-history]by default from show cpu-traffic-stats View the CPU traffic statistics.
PAGE 127
NOTE: After debugging is complete, use the no debug cpu-traffic-stats command to shut off traffic statistics collection.
PAGE 128
Example DellEMC# show debug Generic IP: IP packet debugging is on for ManagementEthernet 1/1 Port-channel 1-2 Port-channel 5 GigabitEthernet 4/1-4/3,4/5-4/6,4/10-4/11,20 GigabitEthernet 5/1-5/3,5/5-5/6,5/10-5/11,15,17,19,21 ICMP packet debugging is on for GigabitEthernet 5/1,5/2,5/4,5/6,5/8,5/10,5/12,5/14,5/16 DellEMC# show environment View system component status (for example, temperature or voltage).
PAGE 129
Usage Information Version Description 7.8.1.0 The output of the show environment fan command for the S Series is changed to display fan speeds instead of showing the fan status as up or down. The following example shows the output of the show environment command.
PAGE 130
Usage Information Example (S3100) Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.4 Output expanded to include Piece Part ID (PPID) and eSR4 optics. 8.3.11.1 Introduced on the Z9000. 7.6.1.
PAGE 131
Parameters Defaults all (Optional)Displays the login statistics of all users in the last 30 days or the custom defined time period. time-period days (Optional)Displays the number of failed login attempts by the current user in the specified period.
PAGE 132
Successful login attempt(s) in last 30 day(s): 1 -----------------------------------------------------------------The following is sample output of the show login statistics all command. DellEMC#show login statistics all -----------------------------------------------------------------User: admin Last login time: 08:54:28 UTC Wed Mar 23 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 133
The following is sample output of the show login statistics unsuccessful-attempts user login-id command. DellEMC# show login statistics unsuccessful-attempts user admin There were 3 unsuccessful login attempt(s) for user admin in last 12 day(s). The following is sample output of the show login statistics successful-attempts command. DellEMC#show login statistics successful-attempts There were 4 successful login attempt(s) for user admin in last 30 day(s).
PAGE 134
Example DellEMC#show memory stack-unit 1 Statistics On Unit 1 Processor =========================== Total(b) Used(b) Free(b) 3177185280 2310248 3174875032 DellEMC# Lowest(b) 3174676264 Largest(b) 3174875032 show processes cpu Display CPU usage information based on processes running. Syntax show processes cpu [management-unit [1-99 | details] | stack-unit id [1-99]| summary ] Parameters management-unit (OPTIONAL) Display processes running in the control processor.
PAGE 135
stack-unit summary | Unit Number Summary of CPU utilization Pipe through a command DellEMC# show processes cpu summary CPU utilization 5Sec 1Min 5Min ------------------------------------------UNIT1 3% 3% 1% DellEMC# show processes cpu stack-unit 1 CPUID 5sec 1min 5min -------------------------------------------------CORE 0 13.17 11.53 0.00 CORE 2 9.38 12.16 0.00 Overall 11.28 11.84 0.
PAGE 136
statMgr sflCp snmp dpi_cmow dpi_taskcmo 49 1010 101 10000 0.05% 0.07% 0.08% 0 48 30 3 10000 0.00% 0.00% 0.00% 0 47 0 0 0 0.00% 0.00% 0.00% 0 46 0 0 0 0.00% 0.00% 0.
PAGE 137
show processes ipc flow-control Display the single window protocol queue (SWPQ) statistics. Syntax Parameters Defaults show processes ipc flow-control [cp] cp (OPTIONAL) Enter the keyword cp to view the control processor’s SWPQ statistics. none Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 138
Field Description Retr /Available Retra Number of retries left Total/ Max Retra Number of retries allowed Important Points: ● The SWP provides flow control-based reliable communication between the sending and receiving software tasks. ● A sending task enqueues messages into the SWP queue3 for a receiving task and waits for an acknowledgement. ● If no response is received within a defined period of time, the SWP timeout mechanism resubmits the message at the head of the FIFO queue.
PAGE 139
summary Enter the keyword summary for a brief summary of memory availability and usage on all stack members. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 140
For the S-Series, the output of the show memory command and this command differ based on which Dell OS processes are counted. ● In the show memory output, the memory size is equal to the size of the application processes. ● In the output of this command, the memory size is equal to the size of the application processes plus the size of the system processes.
PAGE 141
all (OPTIONAL) Enter the keyword stack-unit and the keyword all to view the reason for the last system reboot of all stack units in the stack. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example — Userinitiated reboot with the reload command Example — System reboot due to the upgrade command Example — System reboot for unknown reasons This guide is platform-specific.
PAGE 142
Example — Reset reason of a single stack unit Example — Reset reason of all stack units DellEMC# show reset-reason stack-unit 1 Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 DellEMC#show reset-reason stack-unit all Last Reset Reason: --------------------Type Cause Time ----------------------------------------------------------------------------------stack-unit 1 Reboot by Software 11/05/2017-09:04 stack-unit 2 Reboot by Software 11/05/2017-09:04 stack-unit 3 Cold Reset N/A stack-un
PAGE 143
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced for the C-Series and S-Series.
PAGE 144
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for the disabled-ports parameter . 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, use the show reload-type command.
PAGE 145
---------------------------------------------------------------------------------1 1 up up 7058 up 7058 Speed in RPM show tech-support Display a collection of data from other show commands, necessary for Dell EMC Networking technical support to perform troubleshooting. Syntax Parameters show tech-support [stack-unit unit-id | page] stack-unit (OPTIONAL) Enter the keywords stack-unit to view CPU memory usage for the stack member designated by unit-id.
PAGE 146
The save option works with other filtering commands. This allows you to save specific information of a show command. The save entry must always be the last option.
PAGE 147
Dell Application Software Version: 9.14(0.0) Copyright (c) 1999-2016 by Dell Inc. All Rights Reserved. Build Time: Wed Mar 9 18:13:18 2016 Build Path: /sites/maa/work/swcontractors02_2/mzaid/zaid_imain/SW/SRC Dell EMC Networking OS uptime is 1 day(s), 17 hour(s), 40 minute(s) System image file is "scripts231" System Type: S3124P Control Processor: Broadcom 56340 (ver A0) with 2 Gbytes (2147483648 bytes) of memory, core(s) 1. 1G bytes of boot flash memory. 1 28-port GE/TE (S3100) 24 GigabitEthernet/IEEE 802.
PAGE 148
Control Processor: Broadcom 56340 (ver A0) with 2 Gbytes (2147483648 bytes) of memory, core(s) 1. 1G bytes of boot flash memory. 1 28-port GE/TE (S3100) 24 GigabitEthernet/IEEE 802.3 interface(s) 2 Ten GigabitEthernet/IEEE 802.3 interface(s) ------------ show clock ------------04:56:09.650 UTC Thu Jun 4 2017 ------------ show running-config ------------Current Configuration ... ! Version 1-0(0-4743) ! Last configuration change at Thu Jun 4 04:53:32 2020 by admin ! boot system stack-unit 1 primary tftp://10.
PAGE 149
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. telnet Connect through Telnet to a server. The Telnet client and server in Dell EMC Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router. NOTE: The Telnet server and client are VRF-aware.
PAGE 150
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Added support for source-interface for link-local IPv6 addressing. 8.3.11.1 Introduced on the Z9000. 8.2.1.
PAGE 151
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series.
PAGE 152
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. traceroute View a packet’s path to a specific device. Syntax traceroute {host | vrf instance | ip-address | ipv6-address} Parameters host Enter the name of device. vrf instance (Optional) E-Series Only: Enter the keyword vrf then the VRF Instance name. ip-address Enter the IP address of the device in dotted decimal format.
PAGE 153
Usage Information Version Description 8.1.1.0 Introduced on the E-Series (IPv4 only). 7.9.1.0 Introduced VRF. 7.6.1.0 Added support for the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for IPv6 address on the E-Series. E-Series Original command.
PAGE 154
undebug all Disable all debug operations on the system. Syntax undebug all Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 155
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 156
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 157
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 158
• • • • • dot1x mac show show show tx-period dot1x cos-mapping interface dot1x interface dot1x profile dot1x critical-vlan Configure critical-VLAN for users or devices when authentication server is not reachable. Syntax [no] dot1x critical-vlan vlan-id Parameters Defaults vlan-id Enter the VLAN identifier. The VLAN-ID range is from 1 to 4094. Not Configured. Command Modes INTERFACE INTERFACE (BATCH MODE) Command History Usage Information This guide is platform-specific.
PAGE 159
Auth PAE State: Backend State: Authenticated Idle debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x. interface Restricts the debugging information to an interface.
PAGE 160
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3.
PAGE 161
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 162
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: ● Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). ● Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command).
PAGE 163
Related Commands ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 164
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 165
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 166
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.
PAGE 167
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode.
PAGE 168
Parameters Defaults force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. None Command Modes Auto Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 169
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9010. The dot1x profile command configures a dot1x profile to define a list of trusted supplicant MAC addresses. Maximum number of dot1x profiles is limited to 10.
PAGE 170
dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command. Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which reauthentication is initiated. The range is from 1 to 31536000 (one year). The default is 3600 (1 hour).
PAGE 171
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 172
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. When you configure the dot1x server-timeout value, take into account the communication medium used to communicate with an authentication server and the number of RADIUS servers configured.
PAGE 173
● Ensure that no configured profile exists at the time of configuring the static-mab command. ● Use this command in Interface Batch Mode to enable static MAB in a dual-homing setup. Example DellEMC(conf)#do show dot1x interface twentyFiveGigE 1/41 802.
PAGE 174
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command.
PAGE 175
mac Configure a list of supplicant MAC addresses for dot1x profile represented with a profile-name. Syntax Parameters Defaults [no] mac {mac-address1 mac-address2… mac-address6} mac-address1 mac-address2 … mac-address6 Enter the keyword mac and type the 48– bit MAC addresses using the H.H.H format. A maximum of 6 MAC addresses are allowed. None Command Modes DOT1X PROFILE CONFIG (conf-dot1x-profile) CONFIGURATION TERMINAL BATCH Command History Usage Information This guide is platform-specific.
PAGE 176
Command Modes ● EXEC ● EXEC privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 177
4 5 6 7 DellEMC# 3 2 1 0 show dot1x interface Display the 802.1X configuration of an interface. Syntax Parameters Defaults show dot1x interface interface [mac-address mac-address] interface Enter one of the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 178
802.
PAGE 179
Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: DellEMC# AUTHORIZED(GUEST
PAGE 180
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 181
• • • • • • • • • • • • seq arp (for Extended MAC ACLs) seq ether-type (for Extended MAC ACLs) seq (for IP ACLs) seq (for IPv6 ACLs) permit udp (for IPv6 ACLs) permit tcp (for IPv6 ACLs) permit icmp (for IPv6 ACLs) permit (for IPv6 ACLs) deny udp (for IPv6 ACLs) deny tcp (for IPv6 ACLs) deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
PAGE 182
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode.
PAGE 183
show config Display the current ACL configuration. Syntax show config Command Modes ● ● ● ● Command History Example CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 184
access-class Apply a standard ACL to a terminal line. Syntax access-class access-list-name [ipv4 | ipv6] To remove an ACL, use the no access-class command. Parameters Defaults access-list-name Enter the name of a configured Standard ACL, up to 140 characters. ipv4 Enter the keyword ipv4 to configure an IPv4 access class. ipv6 Enter the keyword ipv6 to configure an IPv6 access class. Not configured. Command Modes LINE Command History Usage Information This guide is platform-specific.
PAGE 185
already configured on this terminal line. Before applying either IPv4 or IPv6 filtering, first undo the generic configuration using the no access-class access-list-name command. Similarly, if you have configured either IPv4 or IPv6 specific filtering on a terminal line, you cannot apply generic IP ACLs on top of this configuration. Before applying the generic ACL configuration, first undo the existing configuration using the no access-class access-list-name [ipv4 | ipv6] command.
PAGE 186
Parameters Defaults access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic. out Enter the keyword out to apply the ACL to outgoing traffic. implicit-permit (OPTIONAL) Enter the keyword implicit-permit to change the default action of the ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped).
PAGE 187
NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces. NOTE: If you apply outbound(egress) IP acl on a switch port, the filter applies only for routed traffic egressing out of that port. To associate an access-list to a non-default VRF, use the vrf attribute of this command.
PAGE 188
show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters. Syntax show ip accounting {access-list access-list-name | cam_count} interface interface [vrf vrf-name] Parameters access-list-name Enter the name of the ACL to be displayed. cam_count List the count of the CAM rules for this ACL.
PAGE 189
Usage Information Example NOTE: The vrf option is available only when VRF feature is enabled. show ip accounting accesslists Field Description “Extended IP...” Displays the name of the IP ACL. “seq 5...” Displays the filter. If the keywords count or byte were configured in the filter, the number of packets or bytes the filter processes is displayed at the end of the line. “order 4” Displays the QoS order of priority for the ACL entry.
PAGE 190
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.5.1.0 Added support for the 4-port 40G line cards on the E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Standard IP ACL Commands When you create an ACL without any rule and then apply it to an interface, the ACL behavior reflects an implicit permit. The platform supports both Ingress and Egress IP ACLs.
PAGE 191
no-drop Defaults Enter the keywords no-drop to match only the forwarded packets. Not configured. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.
PAGE 192
Parameters Defaults access-list-name Enter a string up to 140 characters long as the ACL name. All IP access lists contain an implicit “deny any,” that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 193
● Use the no permit {source [mask] | any | host ip-address} command. Parameters Defaults source Enter the IP address in dotted decimal format of the network from which the packet was sent. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 194
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.
PAGE 195
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series (IPv6). 8.1.1.0 Introduced on the E-Series (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 196
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments. no-drop Enter the keywords no-drop to match only the forwarded packets.
PAGE 197
● If you configure sequence-number, the sequence-number is used as a tie breaker for rules with the same order. Related Commands ● deny — configure a filter to drop packets. ● permit — configure a filter to forward packets. Extended IP ACL Commands When an ACL is created without any rule and then applied to an interface, ACL behavior reflects an implicit permit. The following commands configure extended IP ACLs, which in addition to the IP address, also examine the packet’s protocol type.
PAGE 198
Defaults byte (OPTIONAL) Enter the keyword byte to count bytes that the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority).
PAGE 199
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the Quality of Service section in the Dell EMC Networking OS Configuration Guide. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The monitor option is relevant in the context of flow-based monitoring only.
PAGE 200
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower order numbers have a higher priority) If you did not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments.
PAGE 201
deny tcp Configure a filter that drops transmission control protocol (TCP) packets meeting the filter criteria. Syntax deny tcp {source mask | any | host ip-address} [bit] [operator port [port]] {destination mask | any | host ip-address} [ttl operator] [dscp] [bit] [operator port [port]] [count [bytes] [order] [fragments] [monitor] [nodrop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 202
● 25 = SMTP ● 169 = SNMP Defaults destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes.
PAGE 203
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only.
PAGE 204
● Use the no deny udp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters Defaults source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 205
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 206
2 3 4 5 6 7 8 0000111111000000 0001000000000000 0001100000000000 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111111111000000 1111100000000000 1111110000000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 4032 4096 6144 7168 7680 7936 8000 4095 6143 7167 7679 7935 7999 8000 64 2048 1024 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM.
PAGE 207
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification about entries allowed per ACL, refer to your line card documentation. Prior to 7.8.1.0, names are up to 16 characters long.
PAGE 208
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments.
PAGE 209
Related Commands ● ip access-list extended — create an extended ACL. ● ● permit tcp — assign a permit filter for TCP packets. ● permit udp — assign a permit filter for UDP packets. permit tcp To pass TCP packets meeting the filter criteria, configure a filter.
PAGE 210
port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● 23 = Telnet ● 20 and 21 = FTP ● 25 = SMTP ● 169 = SNMP Defaults destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.
PAGE 211
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 212
permit udp To pass UDP packets meeting the filter criteria, configure a filter. Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [ttl operator] [dscp] [operator port [port]] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 213
monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. no-drop Defaults Enter the keywords no-drop to match only the forwarded packets. Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 214
Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 215
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 216
● gt = greater than ● lt = less than ● range = inclusive range of ports (you must specify two ports for the port parameter.) portnumber (OPTIONAL) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 217
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P0) Included support for using logical names of a protocol to configure an IP access list in both TCP and UDP on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 218
Related Commands ● deny — configure a filter to drop packets. ● permit — configure a filter to forward packets. Common MAC Access List Commands The following commands are available within both MAC ACL modes (Standard and Extended) and do not have mode-specific options. These commands allow you to clear, display, and assign MAC ACL configurations. The platform supports both Ingress and Egress MAC ACLs. The MAC ACL can be applied on Physical, Port-channel and VLAN interfaces.
PAGE 219
mac access-group Apply a MAC ACL to traffic entering or exiting an interface. You can apply a MAC ACL on a physical, port-channel, or VLAN interface. Syntax mac access-group access-list-name {in [vlan vlan-range] | out} To delete a MAC access-group, use the no mac access-group mac-list-name command. Parameters access-list-name Enter the name of a configured MAC access list, up to 140 characters. NOTE: This option is available only with the keyword in option.
PAGE 220
Version Description 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information You can assign one ingress ACL and one egress ACL (standard or extended) to an interface. Related Commands ● mac access-list standard — configure a standard MAC ACL. ● mac access-list extended — configure an extended MAC ACL.
PAGE 221
Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.1.0 Introduced. show mac accounting access-list Display MAC access list configurations and counters (if configured). Syntax Parameters show mac accounting access-list access-list-name interface interface in | out access-list-name Enter the name of a configured MAC ACL, up to 140 characters.
PAGE 222
Usage Information Example Version Description 7.5.1.0 Introduced on the C-Series 6.1.1.0 Introduced on the E-Series. The ACL hit counters increment the counters for each matching rule, not just the first matching rule.
PAGE 223
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 224
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 225
Defaults log (OPTIONAL) Enter the keyword log to include ACL messages in the log. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated.
PAGE 226
seq To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {any | mac-source-address mac-source-address-mask} command.
PAGE 227
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 228
mac-destination- Specify which bits in the MAC address must match. address-mask The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. Defaults ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the following Ethertypes: ● ev2 - is the Ethernet II frame format ● llc - is the IEEE 802.3 frame format ● snap - is the IEEE 802.
PAGE 229
Usage Information Version Description 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead.
PAGE 230
Usage Information Version Description 6.1.1.0 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specifications about entries allowed per ACL, refer to your line card documentation. Prior to 7.8.1.0, names are up to 16 characters long.
PAGE 231
The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. Defaults ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the following Ethertypes: ● ev2 - is the Ethernet II frame format ● llc - is the IEEE 802.3 frame format ● snap - is the IEEE 802.3 SNAP frame format count (OPTIONAL) Enter the keyword count to count packets the filter processes.
PAGE 232
NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands ● deny — configure a MAC ACL filter to drop packets. ● seq — configure a MAC ACL filter with a specified sequence number. IP Prefix List Commands When you create an access-list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit.
PAGE 233
deny To drop packets meeting the criteria specified, configure a filter. Syntax deny ip-prefix [ge min-prefix-length] [le max-prefix-length] To delete a drop filter, use the no deny ip-prefix command. Parameters ip-prefix Specify an IP prefix in the network/length format. For example, 35.0.0.0/ 8 means match the first 8 bits of address 35.0.0.0. ge min-prefix- (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32.
PAGE 234
Parameters prefix-name Enter a string up to 16 characters long as the name of the prefix list, up to 140 characters long. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 235
any (OPTIONAL) Enter the keyword any to match any packets. ip-prefix /nn (OPTIONAL) Specify an IP prefix in the network/length format. For example, 35.0.0.0/8 means match the first 8 bits of address 35.0.0.0. ge min-prefix- (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32. length le max-prefix- length bitmask number Defaults (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32.
PAGE 236
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 237
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 238
Example Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 239
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. The continue feature allows movement from one route-map entry to a specific route-map entry (the sequence number). If you do not specify the sequence number, the continue feature simply moves to the next sequence number (also known as an implied continue). If a match clause exists, the continue feature executes only after a successful match occurs.
PAGE 240
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-7.7.1.0 Introduced. ● route-map — enable a route map.
PAGE 241
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● set as-path — add information to the BGP AS_PATH attribute. match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Syntax match community community-list-name [exact] To delete a community match filter, use the no match community command.
PAGE 242
match interface To match routes whose next hop is on the interface specified, configure a filter. Syntax match interface interface To remove a match, use the no match interface interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 243
match ip address To match routes based on IP addresses specified in an access list, configure a filter. Syntax match ip address prefix-list-name To delete a match, use the no match ip address prefix-list-name command. Parameters Defaults prefix-list-name Enter the name of configured prefix list, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific.
PAGE 244
Parameters Defaults prefix-list prefix- Enter the keywords prefix-list and then enter the name of configured prefix list-name list, up 10 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 245
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 246
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 247
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 248
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface.
PAGE 249
Related Commands Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address.
PAGE 250
Usage Information Example Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 251
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. You can prepend up to eight AS numbers to a BGP route. This command influences best path selection in BGP by inserting a tag or AS number into the AS_PATH attribute.
PAGE 252
Related Commands ● ● ● ● set set set set level — specify the OSPF area for route redistribution. metric — specify the metric value assigned to redistributed routes. metric-type — specify the metric type assigned to redistributed routes. tag — specify the tag assigned to redistributed routes. set comm-list delete To remove the specified community list from the BGP route’s COMMUNITY attribute, configure a filter.
PAGE 253
Related Commands ● match community — redistribute routes that match the COMMUNITY attribute. ● set community — specify a COMMUNITY attribute. set community Allows you to assign a BGP COMMUNITY attribute. Syntax set community {community-number | local-as | no-advertise | no-export | none} [additive] To delete a BGP COMMUNITY attribute assignment, use the no set community {communitynumber | local-as | no-advertise | no-export | none} command.
PAGE 254
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● match community — redistribute routes that match the COMMUNITY attribute. ● show ip bgp community — display BGP community groups. set level To specify the IS-IS level or OSPF area to which matched routes are redistributed, configure a filter.
PAGE 255
Related Commands Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● set set set set automatic-tag — compute the tag value of the route. metric — specify the metric value assigned to redistributed routes. metric-type — specify the metric type assigned to redistributed routes. tag — specify the tag assigned to redistributed routes.
PAGE 256
Usage Information The set local-preference command changes the LOCAL_PREF attribute for routes meeting the route map criteria. To change the LOCAL_PREF for all routes, use the bgp default localpreference command. Related Commands ● bgp default local-preference — change the default LOCAL_PREF attribute for all routes. set metric To assign a new metric to redistributed routes, configure a filter. Syntax set metric [+ | -] metric-value To delete a setting, enter no set metric.
PAGE 257
set metric-type To assign a new route type for routes redistributed to OSPF, configure a filter. Syntax set metric-type {internal | external | type-1 | type-2} To delete a setting, use the no set metric-type command. Parameters Defaults internal Enter the keyword internal to assign the Interior Gateway Protocol metric of the next hop as the route’s BGP MULTI_EXIT_DES (MED) value. external Enter the keyword external to assign the IS-IS external metric.
PAGE 258
To delete the setting, use the no set next-hop ip-address command. Parameters Defaults ip-address Specify an IP address in dotted decimal format. Not configured. Command Modes ROUTE-MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 259
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 260
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● set set set set automatic-tag — compute the tag value of the route.
PAGE 261
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you do not use the set weight command, router-originated paths have a weight attribute of 32768 and all other paths have a weight attribute of zero.
PAGE 262
seq 25 permit 192.0.0.0 bitmask 192.0.0.0 DellEMC(conf-nprefixl)# show route-map Display the current route map configurations. Syntax show route-map [map-name] Parameters map-name (OPTIONAL) Enter the name of a configured route map, up to 140 characters. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands 262 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 263
AS-Path Commands The following commands configure AS-Path ACLs. ip as-path access-list Enter AS-PATH ACL mode and configure an access control list based on the BGP AS_PATH attribute. Syntax Parameters Defaults ip as-path access-list as-path-name as-path-name Enter the access-list name, up to 140 characters. Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific.
PAGE 264
Example Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 265
Example Version Description 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series. DellEMC(conf)# ip community-list TestComList DellEMC(config-community-list)# show ip community-lists Display configured IP community lists in alphabetic order.
PAGE 266
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 267
Related Commands ● ip access-list standard — configure a standard ACL. ● permit — configure a permit filter. deny (for Extended IP ACLs) Configure a filter that drops IP packets meeting the filter criteria.
PAGE 268
Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 269
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 270
● Use the no deny tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters Defaults ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 271
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 272
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 273
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 274
Parameters Defaults ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 275
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 276
Usage Information Version Description 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 277
Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 278
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
PAGE 279
permit (for Standard IP ACLs) To permit packets from a specific source IP address to leave the switch, configure a filter. Syntax permit {source [mask]| any | host ip-address} [count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit {source [mask] | any | host ip-address} command.
PAGE 280
You can activate flow-based monitoring for a monitoring session by entering theflow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 281
Usage Information Version Description 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 282
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 283
Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 284
permit udp (for Extended IP ACLs) To pass UDP packets meeting the filter criteria, configure a filter. Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [ttl operator] [dscp] [operator port [port]] [count [byte]] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]][monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 285
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 286
● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands.
PAGE 287
packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands ● ip access-list extended — create an extended ACL. ● permit tcp — assign a permit filter for TCP packets. ● permit udp — assign a permit filter for UDP packets. permit (for Standard MAC ACLs) To forward packets from a specific source MAC address, configure a filter.
PAGE 288
and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 289
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 290
● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands.
PAGE 291
Related Commands ● ip access-list extended — create an extended ACL. ● permit — assign a permit filter for IP packets. ● permit udp — assign a permit filter for UDP packets. seq arp (for Extended MAC ACLs) Configure an egress filter with a sequence number that filters ARP packets meeting this criteria. This command is supported only on 12-port GE line cards with SFP optics. For specifications, refer to your line card documentation. NOTE: Only the options that have been newly introduced in Release 9.3(0.
PAGE 292
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, standard and extended IPv6 ACLs, and standard and extended MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 293
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 294
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
PAGE 295
seq (for IPv6 ACLs) Assign a sequence number to a deny or permit the filter in an IPv6 access list while creating the filter. Syntax seq sequence-number {deny | permit} {ipv6-protocol-number | icmp | ip | tcp | udp} {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [operator port [portnumber ]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To delete a filter, use the no seq sequence-number command.
PAGE 296
which the generation of ACL logs is terminate with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 297
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [operator port [port]] [ttl operator] [count [byte]] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 298
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 299
● syn: synchronize sequence numbers ● urg: urgent field operator (OPTIONAL) Enter one of the following logical operand: ● eq = equal to ● neq = not equal to ● gt = greater than ● lt = less than ● range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 300
Usage Information Version Description 9.11(2.0P0) Added the established parameter on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 301
Defaults host ipv6address Enter the keyword host then the IPv6 address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value.
PAGE 302
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 303
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 304
● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 305
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 306
● ● ● ● Defaults 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 307
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 308
● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 309
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 310
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 311
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements. Topics: • • • • • • • • • • member vlan ip access-group show acl-vlan-group show cam-acl-vlan cam-acl-vlan show cam-usage show running config acl-vlan-group acl-vlan-group show acl-vlan-group detail description (ACL VLAN Group) member vlan Add VLAN members to an ACL VLAN group.
PAGE 312
You can create an ACL VLAN group and attach the ACL with the VLAN members. The optimization is applicable only when you create an ACL VLAN group. If you apply an ACL separately on the VLAN interface, each ACL has a mapping with the VLAN and increased CAM space utilization occurs. Attaching an ACL individually to VLAN interfaces is similar to the behavior of ACL-VLAN mapping storage in CAM prior to the implementation of the ACL VLAN group functionality.
PAGE 313
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output.
PAGE 314
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.
PAGE 315
Default vlaniscsi <0-2> Allocate the number of FP blocks for VLAN iSCSI counters. vlanaclopt <0-2> Allocate the number of FP blocks for the ACL VLAN optimization feature. If you use the default keyword with the cam-acl-vlan command, the FP blocks allocated for VLAN processes are restored to their default values. No FP blocks or dynamic VLAN Content Aware Processor (VCAP) groups are allocated for VLAN operations by default.
PAGE 316
Usage Information The following regions must be provided in the show cam-usage output: ● L3AclCam ● L2AclCam ● V6AclCam The following table describes the output fields of this show command: Example 1: Output of the show cam-usage Command 316 Field Description StackUnit The Stack unit number Portpipe The hardware path that packets follow through a system for ACL optimization CAM Partition Type of area in the CAM block that is used for ACL VLAN groups Total CAM Total amount of space in the CAM bl
PAGE 317
| | IN-NLB ACL | 0 | | | IPMAC ACL | 0 | | | OUT-L2 ACL | 206 | | | OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | Codes: * - cam usage is above 90%.
PAGE 318
| OUT-V6 ACL | 178 | 2 | 0 | IN-L3 FIB | 49152 | | | IN-L3 ACL | 1024 | | | IN-V6 ACL | 0 | | | OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | 3 | 0 | IN-L3 FIB | 49152 | | | IN-L3 ACL | 1024 | | | IN-V6 ACL | 0 | | | OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | Codes: * - cam usage is above 90%.
PAGE 319
Examples Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms The following sample output shows the line-by-line style display when using the show runningconfig acl-vlan-group option.
PAGE 320
Attaching an ACL individually to VLAN interfaces is similar to the behavior of ACL-VLAN mapping storage in CAM prior to the implementation of the ACL VLAN group functionality. show acl-vlan-group detail Display all the ACL VLAN Groups or display a specific ACL VLAN Group by name. To display the names in their entirety, the output displays in a line-by-line format. Syntax show acl-vlan-group detail Parameters detail Display information in a line-by-line format to display the names in their entirety.
PAGE 321
Parameters Default description Enter a description to identify the ACL VLAN group (80 characters maximum). No default behavior or values Command Modes CONFIGURATION (conf-acl-vl-grp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.
PAGE 322
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 323
Command Modes ROUTER OSPF ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
PAGE 324
disable values configured with the bfd neighbor command or configured for the peer group to which a neighbor belongs. The neighbors inherit only the global timer values (configured with the bfd neighbor command). You can only enable BFD for VRRP in INTERFACE command mode (vrrp bfd all-neighbors). You can enable BFD on both default and nondefault VRFs for OSPF and BGP protocols for both IPv4 and IPv6 neighbors. NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions.
PAGE 325
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 326
bfd interval Specify non-default BFD session parameters beginning with the transmission interval. Syntax bfd interval interval min_rx min_rx multiplier value role {active | passive} Parameters interval milliseconds min_rx milliseconds Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200. Dell EMC recommends using more than 100 milliseconds.
PAGE 327
bfd protocol-liveness Enable the BFD protocol liveness feature. Syntax bfd protocol-liveness Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.
PAGE 328
role [active | passive] Enter the role that the local system assumes: ● Active — active system initiates the BFD session. Both systems can be active for the same session. ● Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is Active. Defaults See Parameters. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 329
min_rx milliseconds Enter the keywords min_rx to specify the minimum rate at which the local system receives control packets from the remote system. The range is from 50 to 1000. The default is 200. multiplier value Enter the keyword multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3. role [active | passive] Enter the role that the local system assumes: ● Active — active system initiates the BFD session.
PAGE 330
multiplier value Enter the keyword multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3. role [active | passive] Enter the role that the local system assumes: ● Active — active system initiates the BFD session. Both systems can be active for the same session. ● Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system.
PAGE 331
multiplier value Enter the keywords multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3. role [active | passive] Enter the role that the local system assumes: ● Active — active system initiates the BFD session. Both systems can be active for the same session. ● Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system.
PAGE 332
Defaults See Parameters. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on Z9000. 8.3.
PAGE 333
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series.
PAGE 334
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series.
PAGE 335
Example Version Description 9.11(2.1P1) Introduced the vrf keyword on all the remaining Dell EMC Networking OS platforms. 9.10(0.2) Introduced the vrf keyword on the S3048–ON, S4048–ON, S4048T-ON, S6010– ON, Z9100–ON, and S6100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.
PAGE 336
Statistics: Number of packets received from neighbor: 376 Number of packets sent to neighbor: 314 Number of state changes: 2 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 6 DellEMC# Related Commands ● bfd all-neighbors — establish BFD sessions with all neighbors discovered by the IS-IS protocol or OSPF protocol out of all interfaces. vrrp bfd neighbor Establish a BFD for VRRP session with a neighbor.
PAGE 337
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 338
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 339
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 340
Defaults Disabled Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 341
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
PAGE 342
bgp asnotation asdot DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process.
PAGE 343
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipathrelax command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 344
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The software compares the MEDs only if the path contains no external autonomous system numbers.
PAGE 345
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 346
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 347
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster.
PAGE 348
The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation. Dell EMC Networking OS accepts confederation EBGP peers without a LOCAL_PREF attribute. The software sends AS_CONFED_SET and accepts AS_CONFED_SET and AS_CONF_SEQ.
PAGE 349
Usage Information All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. After specifying autonomous systems numbers for the BGP confederation, recycle the peers to update their configuration. Related Commands ● bgp confederation identifier — configure a confederation ID.
PAGE 350
value, the flapping route is no longer advertised (that is, it is suppressed). The range is from 1 to 20000. The default is 2000. max-suppresstime (OPTIONAL) Enter the maximum number of minutes a route can be suppressed. The default is four times the half-life value. The range is from 1 to 255. The default is 60 minutes. route-map map- (OPTIONAL) Enter the keyword route-map then the name of a configured route map. name Only match commands in the configured route map are supported. Defaults Disabled.
PAGE 351
Defaults 100 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 352
Usage Information Version Description 9.7(0.0) Introduced on the S-Series. 9.2(1.0) Introduced on the Z9500. Configuring or un-configuring the command brings down and brings up the BGP Route Manager, this results in tear down and re-establishment of all active sessions. Link Bandwidth has to be configured on the router to tell it to associate Link Bandwidth with prefixes (paths) and/or to use Link Bandwidth in BGP Multipath route selection.
PAGE 353
In the event of an enfore-first-as check failure, the existing BGP session is flapped. Related Commands ● show ip bgp neighbors — view the information the BGP neighbors exchange. ● show ip protocols — view information on routing protocols. bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails.
PAGE 354
Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 355
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 356
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive.
PAGE 357
To disable outbound optimization, enter the no bgp outbound-optimization command. Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Version Description 9.4.(0.0) Introduced on the S4810. 9.2(1.0) Introduced on the Z9500.
PAGE 358
Usage Information Version Description 7.2.1.0 Introduced. This command is a knob to disable BGP next-hop resolution using BGP learned routes. During the nexthop resolution, only the first route that the next-hop resolves through is verified for the route’s protocol source and is checked if the route is learned from BGP or not. The clear ip bgp command is required for this command to take effect and to keep the BGP database consistent. Execute the clear ip bgp command right after executing this command.
PAGE 359
databases. The Regex Engine Performance Enhancement feature optimizes the CPU usage by caching and reusing regular expression evaluation results. This caching and reuse may be at the expensive of RP1 processor memory. Examples DellEMC(conf-router_bgp)# no bgp regex-eval-optz-disable DellEMC(conf-router_bgp)# do show ip protocols Routing Protocol is "ospf 22222" Router ID is 2.2.2.2 Area Routing for Networks 51 10.10.10.0/00 Routing Protocol is "bgp 1" Cluster Id is set to 10.10.10.0 Router Id is set to 10.
PAGE 360
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection.
PAGE 361
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 362
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 363
ipv6–address mask (OPTIONAL) Enter the IPv6 address followed by the network mask to reset only that prefix. filter-list as- (OPTIONAL) Enter the keywords filter-list then the name of a configured AS-PATH list. path-name regexp regular- expression (OPTIONAL) Enter the keyword regexp then regular expressions. Use one or a combination of the following: ● . = (period) any single character (including a white space). ● * = (asterisk) the sequences in a pattern (0 or more sequences).
PAGE 364
clear ip bgp peer-group Reset a peer-group’s BGP sessions. Syntax clear ip bgp [vrf vrf-name] peer-group peer-group-name [ipv4 [multicast | unicast] | ipv6 unicast] [soft {in | out}] Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to reset the peer group corresponding to that VRF. NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF.
PAGE 365
deny bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. Syntax deny bandwidth To disable this setting, enter the no deny bandwidth command. Parameters Defaults bandwidth Enter the keyword bandwidth to specify extended-community attribute as the matching criteria for denying traffic. The range is from 0 to 102400.
PAGE 366
A.B.C.D Enter the IP address of peer in the A.B.C.D format. X:X:X:X::X Enter the IPv6 IP address of peer in the X:X:X:X::X format. dampening Enter the keyword dampening to view BGP dampening. events Enter the keyword events to view BGP protocol events. ipv4 Enter the ipv4 IP address to view the IPV4 route information. ipv6 Enter the ipv6 IP address to view the IPV6 route information. keepalives Enter the keyword keepalives to view BGP keepalives.
PAGE 367
debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 368
To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] events [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP state changes corresponding to that VRF. A.B.C.D (OPTIONAL) Enter the IPv4 address of the neighbor. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peer- (OPTIONAL) Enter the keyword peer-group then the name of the peer group.
PAGE 369
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP keepalive information corresponding to that VRF. A.B.C.D (OPTIONAL) Enter the IPv4 address of the neighbor. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peer- (OPTIONAL) Enter the keyword peer-group then the name of the peer group. group-name in (OPTIONAL) Enter the keyword in to view only inbound keepalive messages.
PAGE 370
peer-group peer- (OPTIONAL) Enter the keyword peer-group then the name of the peer group. group-name in (OPTIONAL) Enter the keyword in to view BGP notifications received from neighbors. out (OPTIONAL) Enter the keyword out to view BGP notifications sent to neighbors Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 371
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 372
ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group to disable or enable all routers within the peer group. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 373
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 374
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. pre-7.7.1.0 Introduced. ● router bgp — enter ROUTER mode on the switch. maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. Syntax maximum-paths {ebgp | ibgp} number To return to the default values, enter the no maximum-paths command.
PAGE 375
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enable this command, use the clear ip bgp * command to recompute the best path. neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/ Subsequent Address Family Identifier).
PAGE 376
NOTE: The no neighbor peer ip-address activate command takes precedence over the no neighbor peer-group-name activate command. The following tables list the neighbor activation and its expected results for IPv4 and IPv6 address families: Table 1. Neighbor activation and update status for peers activated for IPv4 address family S.No Peer – IPv4 address family Peer group Update status for IPv4 prefixes 1. Activate Activate Send Updates 2. Activate No-Activate Send Updates 3.
PAGE 377
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 378
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting. Syntax neighbor {ip-address} advertisement-start seconds To return to the default value, use the no neighbor {ip-address} advertisement-start command.
PAGE 379
neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peer-group-name} allowas-in command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group.
PAGE 380
Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the default route of all routers in that peer group. route-map map- name Defaults (OPTIONAL) Enter the keyword route-map then the name of a configured route map. Not configured. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 381
neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). Syntax neighbor {ip-address | peer-group-name} description text To delete a description, use the no neighbor {ip-address | peer-group-name} description command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. text Defaults Enter a continuous text string up to 80 characters. Not configured.
PAGE 382
If the prefix list is not configured, the default is permit (to allow all routes). Defaults in Enter the keyword in to distribute only inbound traffic. out Enter the keyword out to distribute only outbound traffic. Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 383
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 384
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information When you enable failover, BGP keeps track of IP or IPv6 ability to reach the peer remote address and the peer local address.
PAGE 385
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as. This command automatically restarts the neighbor session for the configuration to take effect.
PAGE 386
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 387
If you do not use the all keyword, the next hop of only eBGP-learned routes is updated by the route reflector. If you use the all keyword, the next hop of both eBGP- and iBGP-learned routes are updated by the route reflector. neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors. Syntax neighbor {ip-address | peer-group-name} password [encryption-type] password To delete a password, use the no neighbor {ip-address | peer-group-name} password command.
PAGE 388
If you specify a BGP peer group by using the peer-group-name parameter, all the members of the peer group inherit the characteristic configured with this command.
PAGE 389
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can assign up to 256 peers to one peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
PAGE 390
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information When you create a peer group, it is disabled (Shut mode). Related Commands ● neighbor peer-group (assigning peers) — assign routers to a peer group.
PAGE 391
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. After you configure a peer group as passive, assign it a subnet using the neighbor softreconfiguration inbound command. For passive eBGP limits, the Remote AS must be different from the AS for this neighbor. Related Commands ● neighbor soft-reconfiguration inbound — assign a subnet to a dynamically configured BGP neighbor.
PAGE 392
Usage Information To accept 4-byte formats before entering a 4 byte AS Number, configure your system. If the number parameter is the same as the AS number used in the router bgp command, the remote AS entry in the neighbor is considered an internal BGP peer entry. This command creates a peer and the newly created peer is disabled (Shutdown). This command automatically restarts the neighbor session for the configuration to take effect.
PAGE 393
Private AS numbers are from 64512 to 65535 (2 byte). neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} route-map map-name {in | out} To remove the route map, use the no neighbor {ip-address | peer-group-name} routemap map-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group.
PAGE 394
neighbor route-reflector-client Configure the router as a route reflector and the specified neighbors as members of the cluster. Syntax neighbor {ip-address | peer-group-name} route-reflector-client To remove one or more neighbors from a cluster, use the no neighbor {ip-address | peergroup-name} route-reflector-client command. If you delete all members of a cluster, you also delete the route-reflector configuration on the router.
PAGE 395
neighbor sender-side-loopdetect Enables sender-side loop detection for BGP. Syntax neighbor {ip-address | peer-group-name} sender-side-loopdetect To disable sender-side loop detection, use the no neighbor {ip-address | peer-group-name} sender-side-loopdetect command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to enable or disable all routers with in the peer group.
PAGE 396
peer-group-name Enter the name of the peer group to send a COMMUNITY attribute to all routers within the peer group. Defaults extended (OPTIONAL) Enter the keyword extended to send extended community attribute. standard (OPTIONAL) Enter the keyword standard to send standard community attribute. Not configured and COMMUNITY attributes are not sent to neighbors. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 397
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 398
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.
PAGE 399
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 400
Usage Information Version Description 9.14(0.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6010–ON, S6100–ON, Z9100–ON, and S6000– ON. The peer remains in idle state based on the configured idle holdtime. The less the idle holdtime, less the peer in idle state. For the new idle holdtime to take effect, you need to shutdown the respective peer manually using neighbor shutdown command and enable the peer again.
PAGE 401
Neighbors are sorted according to the source and destination ip addresses. If an update-source ip address exists, then the source ip address determines the order in which the neighbors are displayed. neighbor weight Assign a weight to the neighbor connection, which is used to determine the best path. Syntax neighbor {ip-address | peer-group-name} weight weight To remove a weight value, use the no neighbor {ip-address | peer-group-name} weight command.
PAGE 402
network Specify the networks for the BGP process and enter them in the BGP routing table. Syntax network ip-address mask [route-map map-name] To remove a network, use the no network ip-address mask [route-map map-name] command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for example, / 24). The mask appears in command outputs in dotted decimal format (A.B.C.D).
PAGE 403
Usage Information Dell EMC Networking OS software resolves the network address the network command configures with the routes in the main routing table to ensure that the networks are reachable using non-BGP routes and non-default routes. As BGP does not query next-hop information corresponding to locally originated routes, a local route with an unreachable next-hop is chosen as the best route.
PAGE 404
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. Although Dell EMC Networking OS does not generate a route due to the backdoor config, there is an option for injecting/sourcing a local route in the presence of network backdoor config on a learned route. permit bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to permit incoming or outgoing traffic.
PAGE 405
● ● ● ● ● ● ● match ip address set community set local-preference set metric set next-hop set origin set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 406
It is possible to keep only one locally originated route in the BGP database. Network command has preference over the re-distributed routes. When the locally originated route is no longer present in the database the other route is automatically installed. Related Commands ● neighbor default-originate — inject the default route. redistribute ospf Redistribute OSPF routes into BGP.
PAGE 407
Usage Information You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes. When you set the route-map with metric-type internal and apply outbound to an EBGP peer/peer-group, the advertised routes corresponding to those peer/peer-groups have the IGP cost set as MED. When you enter the redistribute isis process-id command without any other parameters, Dell EMC Networking OS redistributes all OSPF internal routes, external type 1 routes, and external type 2 routes.
PAGE 408
shutdown all Disables all the BGP neighbors. Syntax shutdown all Use the no shutdown all command to enable all the configured BGP neighbors. Command Modes ROUTER BGP Command History Usage Information Version Description 9.11.0.0 Introduced on the S-Series, Z-Series, MXL, and IOM. You can use this command to disable all the configured BGP neighbors. This command is global for all VRFs.
PAGE 409
shutdown address-family-ipv6–unicast Disables all the BGP neighbors corresponding to the unicast IPv6 address families. Syntax shutdown address-family-ipv6–unicast Use the no shutdown address-family-ipv6–unicast command to enable all the configured BGP neighbors corresponding to the unicast IPv6 address families. Command Modes ROUTER BGP CONFIGURATION Command History Usage Information Version Description 9.11.0.0 Introduced on the S-Series, Z-Series, MXL, and IOM.
PAGE 410
show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system. Syntax show capture bgp-pdu neighbor ipv4-address Parameters ipv4-address Enter the IPv4 address (in dotted decimal format) of the BGP address to display packet information for that address. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 411
ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] DellEMC# show config View the current ROUTER BGP configuration. Syntax show config Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 412
routes}] [network[network-mask]]] [next-hop] [paths] [peer-group peergroup-name] [regexp regular-expression] [summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view ipv4– unicast route information corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. ipv4 multicast (OPTIONAL) Enter the keywords ipv4 multicast to view information only related to ipv4 multicast routes.
PAGE 413
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced the [all {received-routes}] option for IPv4 and IPv6 neighbors on S4810 and S4820T. 9.14(0.0) Introduced the [all {received-routes}] option for IPv4 and IPv6 neighbors. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 414
Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete *> *> Network 55.0.0.0/24 66.0.0.0/24 Next Hop 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 200 i 0 200 i All the show and debugs commands display the link band width extended-community prefixed with DMZ-Link-bw along with other extended communities. DellEMC# show ip bgp 3.3.3.0/24 BGP routing table entry for 3.3.3.
PAGE 415
*>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I *>I Related Commands ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 200:0:0:6::/64 200:0:0:7::/64 200:0:0:8::/64 200:0:0:9::/64 200:0:0:a::/64 200:0:0:b::/64 200:0:0:c::/64 200:0:0:d::/64 200:0:0:e::/64 200:0:0:f::/64 200:0:0:10::/64 200:0:0:11::/64 200:0:0:12::/64 200:0:0:13::/64 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 12::2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 i i i i i i i i i i i i i i show ip bgp communit
PAGE 416
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 417
show ip bgp community View information on all routes with Community attributes or view specific BGP community groups. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] community [community-number] [local-as] [no-export] [no-advertise] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information either on all routes with community attributes or specific BGP community routes corresponding to that VRF.
PAGE 418
Usage Information Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found.
PAGE 419
show ip bgp community-list View routes that a specific community list affects. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] community-list community-list-name [exact-match] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes affected by a specific community list corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 420
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 421
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 422
show ip bgp detail Display BGP internal information for the IPv4 Unicast address family. Syntax show ip bgp [ipv4 unicast] detail Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 423
PeerIdBitsP 0x41967120 : softOutSz 16 : RibUpdCtxCBP 0 UpdPeerCtxCBP 0 : UpdPeerCtxAFI 0 : TcpioCtxCB 0 : RedistBlk 1 NextCBPurg 1101119536 : NumPeerToPurge 0 : PeerIBGPCnt 0 : NonDet 0 : DfrdPathSel 0 BGPRst 0 : NumGrCfg 1 : DfrdTmestmp 0 : SnmpTrps 0 : IgnrBestPthASP 0 RstOn 1 : RstMod 1 : RstRole 2 : AFFalgs 7 : RstInt 120 : MaxeorExtInt 361 FixedPartCrt 1 : VarParCrt 1 Packet Capture max allowed length 40960000 : current length 0 Peer Grp List Nbr List Confed Peer List Address Family specific Informatio
PAGE 424
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 425
● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 426
Network *> 55.0.0.0/24 *> 66.0.0.0/24 DellEMC# Next Hop 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 200 400 500 600 i 0 200 500 i show ip bgp flap-statistics View flap statistics on BGP routes.
PAGE 427
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 428
ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 429
* *> 4.0.0.0/8 * * * * 6.0.0.0/20 * *> * * 9.2.0.0/16 * --More-- 63.114.8.33 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 0 0 0 0 0 0 0 0 0 0 0 0 18508 18508 18508 18508 18508 18508 18508 18508 18508 18508 18508 209 209 209 701 209 209 209 ? 209 209 209 7018 ? 1 i 1 i 1 i 1 i 3549 i 3549 i 3549 i 701 i 701 i DellEMC# show ip bgp vrf testinconsistent-as BGP table version is 11, local router ID is 66.66.77.
PAGE 430
flap-statistics (OPTIONAL) Enter the keywords flap-statistics to view flap statistics on the neighbor’s routes. routes (OPTIONAL) Enter the keyword routes to view only the neighbor’s feasible routes. all {received(OPTIONAL) Enter the keywords all {received-routes} then either the routes [ network network address alone (in dotted decimal format) or the network address along [ network-mask ]} with the network mask (in slash prefix format) to view all the information received from neighbors.
PAGE 431
BGP shows the exact information that is exchanged between the BGP peers. It also indicates whether or not this information is received by the BGP peer. The following describes the show ip bgp neighbors command shown in the following examples. The Lines Beginning with: Description BGP neighbor Displays the BGP neighbor address and its AS number. The last phrase in the line indicates whether the link between the BGP router and its neighbor is an external or internal one.
PAGE 432
Member of peer-group port0 for session parameters BGP remote router ID 172.16.0.
PAGE 433
Usage Information Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 434
● * = (asterisk) the sequences in a pattern (zero or more sequences). ● + = (plus) the sequences in a pattern (one or more sequences). ● ? = (question mark) sequences in a pattern (either zero or one sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element. { } = (braces) minimum and the maximum match count.
PAGE 435
Example DellEMC# show ip bgp paths ? community Display community information extcommunity Display extended community information regexp Display path information based on a regular expression | Pipe through a command DellEMC#show ip bgp paths Total 2 Paths Refcount Metric Path 1 0 200 i 1 0 200 i DellEMC# show ip bgp paths community View all unique COMMUNITY numbers in the BGP database.
PAGE 436
Example Field Description Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these communities. Community Displays the community attributes in this BGP path. DellEMC# show ip bgp paths community Total 2 communities Refcount Community 1 NO-ADVERTISE 1 200:1 1000:1 3000:1 DellEMC# show ip bgp peer-group Allows you to view information on the BGP peers in a peer group.
PAGE 437
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. Introduced on S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 438
show ip bgp regexp Display the subset of the BGP routing tables matching the regular expressions specified. Syntax show ip bgp [vrf vrf-name] regexp regular-expression [character] Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to view the subset of BGP routing tables that match the regular expression specified on that VRF.
PAGE 439
Usage Information Example Version Description 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp regexp command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then non-BGP routes exist in the router’s routing table. Metric Displays the BGP router’s metric, if assigned.
PAGE 440
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 441
Field Description AS Displays the AS number of the neighbor. MsgRcvd Displays the number of BGP messages that neighbor received. MsgSent Displays the number of BGP messages that neighbor sent. TblVer Displays the version of the BGP table that was sent to that neighbor. InQ Displays the number of messages from that neighbor waiting to be processed. OutQ Displays the number of messages waiting to be sent to that neighbor.
PAGE 442
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 443
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 444
MBGP Commands Multiprotocol BGP (MBGP) is an enhanced BGP that enables multicast routing policy throughout the internet and connecting multicast topologies between BGP and autonomous systems (ASs). Dell EMC Networking OS MBGP is implemented as per IETF RFC 1858. BGPv4 is supported in the following: Dell EMC Networking OS Version Platform Support 7.8.1.0, MBGP for IPv4 Multicast Only S-Series debug ip bgp dampening View information on routes being dampened.
PAGE 445
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced IPv6 MGBP support for the E-Series. distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command.
PAGE 446
Related Commands ● router bgp — enter ROUTER mode on the switch. show ip bgp dampened-paths View BGP routes that are dampened (non-active). Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF.
PAGE 447
The history paths that the show ip bgp command displays contain only the prefix and the next-hop information. The next-hop information shows the ip address of the neighbor. It does not show the actual next-hop details. The following describes the show ip bgp damp command shown in the following example. Example Field Description Network Displays the network ID to which the route is dampened. From Displays the IP address of the neighbor advertising the dampened route.
PAGE 448
non-trans Defaults (OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 449
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 450
Usage Information Example Version Description 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. The following describes the show ip bgp paths extcommunity command shown in the following example. Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these extended communities.
PAGE 451
deny RT:1234:12 permit regexp 123 deny regexp 234 deny regexp 123 DellEMC# IPv6 BGP Commands IPv6 border gateway protocol (IPv6 BGP) is supported on the platform. BGP is an external gateway protocol that transmits interdomain routing information within and between Autonomous Systems (AS). Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically send messages to update those routing tables.
PAGE 452
Version Description 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced on the E-Series. debug ip bgp ipv6 unicast soft-reconfiguration Enable soft-reconfiguration debugging for IPv6 unicast routes. Syntax debug ip bgp [ipv4-address | ipv6-address | peer-group-name] ipv6 unicast soft-reconfiguration To disable debugging, use the no debug ip bgp [ipv4-address | ipv6-address | peergroup-name] ipv6 unicast soft-reconfiguration command.
PAGE 453
Parameters prefix-list name Enter the name of the prefix list. NOTE: There is a 140-character limit for prefix list names. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 454
Usage Information This command enables soft-reconfiguration for the specified BGP neighbor. BGP stores all updates for inbound IPv6 unicast routes the neighbor receives but does not reset the peer-session. CAUTION: Inbound update storage is a memory-intensive operation. The entire BGP update database from the neighbor is stored in memory regardless of the inbound policy results applied on the neighbor. show ipv6 prefix-list Displays the specified IPv6 prefix list.
PAGE 455
summary Display a summary of RPF routes. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.
PAGE 456
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 457
● ● ● ● ● ● ● ● ● ● ● ● ● ● IPV4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 nlbclusteracl: 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl :0 Openflow : 0 fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 8.
PAGE 458
Iscsioptacl number Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2. ipv4mirracl Enter the ipv4mirracl keyword and then the number of FP blocks for IPv4 mirror ACL. The range is from 0 to 8. You cannot use the ipv4mirracl and ipv4udfmirracl commands at the same time. radius-v4acl Enter the radius-v4acl keyword and then the number of FP blocks for RADIUS dynamic ACL. The range is from 0 to 8.
PAGE 459
If allocation values are not entered for the CAM regions, the value is 0. If you enable BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the command reload conditional nvram-cfg-change. cam-acl-egress Allocate CAM for egress ACLs. Syntax Parameters cam-acl-egress default | l2acl number ipv4acl number ipv6acl number default Reset the egress CAM ACL entries to default settings.
PAGE 460
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 461
Command History Usage Information Example Version Description 9.14.1.0 Introduced on the S4810 and S4820T. 9.13.0.0 Introduced on the MXL, FN IOM, S5000, S4048-ON, S6000, S6000-ON, S3048ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. The no cam-threshold command will set the CAM threshold to 90 percent and silence period to 0. The CAM threshold and silence period configuration is applicable only for Ingress L2, IPv4, IPv6 and Egress L2, IPv4, and IPv6 ACL CAM groups.
PAGE 462
Example DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p
PAGE 463
IPV6(IPV4QOS) Triple Wide Regions: VmanQos, Openflow, ipv4udfmirracl L2Acl : 2 Ipv4Acl : 4 Ipv6Acl* : 2 Ipv4Qos* : 0 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl: 0 ipv4mirracl : 0 * - shared regions show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow) Syntax Parameters Defaults show
PAGE 464
Table 3.
PAGE 465
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 466
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 467
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax Parameters Defaults service-policy rate-limit-cpu-queues policy-name policy-name Enter the service-policy name, using a string up to 32 characters. Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History Usage Information This guide is platform-specific.
PAGE 468
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 469
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload.
PAGE 470
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 471
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 472
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 473
LLDP GVRP STP ISIS DellEMC# any 01:80:c2:00:00:21 01:80:c2:00:00:00 01:80:c2:00:00:14/15 09:00:2b:00:00:04/05 0x88cc any any any any Q8 Q8 Q7 Q9 Q9 CP CP CP CP CP _ _ _ _ Control Plane Policing (CoPP) 473
PAGE 474
12 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 475
is not reachable, the application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
PAGE 476
no-reboot Defaults Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit stack-unit-number command. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 477
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process.
PAGE 478
Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 479
Related Commands Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. ● show hardware stack-unit — display the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
PAGE 480
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 481
show hardware mac Display MAC ACL entries for the specified stack-unit, port-pipe and pipeline ID. Syntax Parameters Defaults show hardware mac {eg-acl | in-acl} stack-unit id port-set 0–0 eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack- unit id Enter the keyword stack-unit to select the stack unit ID.
PAGE 482
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 483
stats [detail] | register} TI monitor Defaults Enter the unit keyword to show information regarding the TI register. None Command Modes ● EXEC ● EXEC Privilege Command History Example (DataPlane) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 484
Example (PartyBus) Example (Drops Unit) Example (PortStats) Example (Register) 484 DellEMC# show hardware stack-unit 1 cpu party-bus statistics Input Statistics: 0 packets, 0 bytes 0 dropped, 0 errors Output Statistics: 0 packets, 0 bytes 0 errors DellEMC# sh hard stack-unit 1 drops unit 0 PortNumber Ingress Drops IngMac Drops Total Mmu Drops 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 EgMac Drops Egress Drops 0 0 0 0 0 0 0 0 DellEMC# DellEMC# show hardware stack-unit 1 unit 0 port-stats ena/ speed/ link auto STP
PAGE 485
0x0061204c ASFPORTSPEED.ge18 = 0x00000000 0x0061304c ASFPORTSPEED.ge19 = 0x00000000 0x0061404c ASFPORTSPEED.ge20 = 0x00000000 0x0061504c ASFPORTSPEED.ge21 = 0x00000000 0x0061604c ASFPORTSPEED.ge22 = 0x00000000 0x0061704c ASFPORTSPEED.ge23 = 0x00000005 0x0061804c ASFPORTSPEED.hg0 = 0x00000007 0x0061904c ASFPORTSPEED.hg1 = 0x00000007 0x0061a04c ASFPORTSPEED.hg2 = 0x00000000 0x0061b04c ASFPORTSPEED.hg3 = 0x00000000 0x0061c04c ASFPORTSPEED.cpu0 = 0x00000000 0x00780000 AUX_ARB_CONTROL.
PAGE 486
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 486 - 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Frame Counter Good Packet Counter Packet/Frame Counter Unicast Frame Counter Multicast Frame Counter Broadcast Frame Counter Byte Counter Control Frame Counter Pause Control Frame Counter Oversized Frame C
PAGE 487
TX TX TX TX TX TX TX TX TX - Debug Debug Debug Debug Debug Debug Debug Debug Debug Counter Counter Counter Counter Counter Counter Counter Counter Counter 3 4 5 6 7 8 9 10 11 --------------------unit: 0 port: 61 (interface Gi 1/60) Description RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX - IPV4 L3 Unicast Frame Counter IPV4 L3 Routed Multicast Packets IPV6 L3 Unicast Frame Counter IPV6
PAGE 488
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Frame Counter Good Packet Counter Packet/Frame Counter Unicast Frame Counter Multicast Frame Counter Broadcast Frame Counter Byte Counter Control Frame Counter Pause Control Frame Counter Oversized Frame Counter Jabbe
PAGE 489
The linkStatus of Front End Port 5 is FALSE The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus of Front End Port 9 is FALSE The linkStatus of Front End Port 10 is FALSE The linkStatus of Front End Port 11 is FALSE The linkStatus of Front End Port 12 is FALSE The linkStatus of Front End Port 13 is FALSE The linkStatus of Front End Port 14 is FALSE The linkStatus of Front End Port 15 is FALSE The linkStatus of Fron
PAGE 490
show hardware buffer interface Display buffer statistics for a specific interface. Syntax show hardware buffer interface interface{priority-group { id | all } | queue { id| all} ] buffer-info Parameters interface interface Enter any of the following keywords and slot/port or number information: ● For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 491
Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet
PAGE 492
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500.
PAGE 493
show hardware buffer-stats-snapshot Displays buffer statistics tracking resource information for a specific interface. Syntax Parameters show hardware buffer-stats-snapshot resource {headroom-pool [detail] | service-pool [detail] interface interface {{priority-group {id | all} | queue ucast {id | all} mcast {id | all} | all} [detail]} headroom-pool detail Enter the keyword headroom-pool followed by the keyword detail to view detailed information about the headroom pool usage.
PAGE 494
Parameters stack-unit stack- Unique ID of the stack unit to select a particular stack member and then enter unit-number one of the following command options to display a collection of data based on the option entered. buffer-statssnapshot unit number buffer-info Display the historical snapshot of buffer statistical values unit Enter the keyword unit along with a port-pipe number. The range is from 0 to 0.
PAGE 495
-------------------------------------------------0 0 0 1 0 0 2 0 0 3 7 0 0 4 6 0 0 5 4 0 0 6 3 0 0 7 0-2,5 0 0 show hardware system-flow Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe. Syntax Parameters Defaults show hardware system-flow stack-unit id port-set number [counters] stack-unit id Enter the keywords stack-unit to select a stack member ID. port-set number [counters] Enter the keywords port-set with a port-pipe number.
PAGE 496
2039 DROP Cases 2038 OSPF1 STUB 2037 OSPF2 STUB 2036 VRRP STUB 2035 L2_DST_HIT+BC MAC+VLAN 4095 2034 L2_DST_HIT+BC MAC 2033 Catch all 384 OSPF[224.0.0.5] Packets 383 OSPF[224.0.0.
PAGE 497
action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, !--------- output truncated -----------------! show hardware vlan-counters Display the hardware VLAN statistics. Syntax Parameters Defaults show hardware vlan-counters vlan-id vlan-id Enter the interface VLAN number. The range is from 1 to 4094. None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific.
PAGE 498
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Included the FEC BER details in the output for 25 and 50GG interfaces of the S5048–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.11(0.
PAGE 499
Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS on COS10 HOL DROPS on COS11 HOL DROPS on COS12 HOL DROPS on COS13 HOL DROPS on COS14 HOL DROPS on COS15 HOL DROPS on COS16 HOL DROPS on COS17 TxPurge CellErr Aged Drops --- Egress MAC counters--Egress FCS Drops --- Egress FORWARD PROCESSOR IPv4 L3UC Ag
PAGE 500
13 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 501
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP.
PAGE 502
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 503
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific.
PAGE 504
Parameters Defaults address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 505
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. excluded-address Prevent the server from leasing an address or range of addresses in the pool.
PAGE 506
hardware-address For manual configurations, specify the client hardware address. Syntax hardware-address address Parameters Defaults address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 507
Usage Information When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.3 or later, the system converts the DHCP CONFIGURATION host command in the running configuration to the hostaddress command. If you downgrade the Dell EMC Networking OS from version 9.14.1.3 or later to an earlier version, any existing host-address command is deleted from the running configuration. If you want to create manual DHCP bindings, use the host command. ip dhcp server Enable DHCP server globally.
PAGE 508
Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 509
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell EMC Networking recommends specifying clients as hybrid.
PAGE 510
network Specify the range of addresses in an address pool. Syntax network network /prefix-length Parameters Defaults network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 511
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 512
show ip dhcp configuration Display the DHCP configuration. Syntax show ip dhcp configuration [global | pool name] Parameters Defaults pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 513
show ip dhcp conflict Display the address conflict log. Syntax Parameters Defaults show ip dhcp conflict address address Display a particular conflict log entry. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 514
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms.
PAGE 515
Related Commands ● arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table. arp inspection-limit Configure dynamic ARP inspection rate-limit to verify the rate of ARP packet received in a port on a specific interval. Syntax arp inspection-limit {rate pps [interval seconds]} Defaults None Command Modes INTERFACE CONFIGURATION Parameters Command History rate pps Enter the keyword rate then the packet per second (pps) value.
PAGE 516
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. ● arp inspection — enable dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. Syntax clear ip dhcp snooping {binding | source-address-validation discardcounters [interface interface]} Parameters binding Clears the binding table.
PAGE 517
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 518
ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] Parameters Defaults remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82. remote-id port Enter the keywords remote-id port to configure the port as the remote id in option–82.
PAGE 519
ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 520
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ipv6 dhcp snooping vlan Enable ipv6 DHCP Snooping on VLAN or range of VLANs.
PAGE 521
Defaults interface type Enter the keyword interface then the type of interface to which the host is connected: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. lease time Enter the keyword lease then the amount of time the IP address are leased. The range is from 1 to 4294967295.
PAGE 522
To delete the DHCP snooping binding entry from DHCP snooping database, use the [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease valuecommand. Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IPv6 address. vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 523
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 524
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 525
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 526
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp source-address-validation Enable the IP Source Guard.
PAGE 527
Usage Information Version Description 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system. ip dhcp relay information-option Enable Option 82.
PAGE 528
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series. DellEMC(conf)# ip dhcp relay information-option vpn ip dhcp relay source-interface Configure IPv4 DHCP relay source interface.
PAGE 529
Related Commands Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface. ipv6 dhcp relay source-interface Configure DHCP relay source IPv6 interface.
PAGE 530
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 531
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
PAGE 532
ipv6-address Default Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Enhanced to support non-default VRF configuration for DHCPv6 helper address. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 533
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 534
Total cam count 5 permit host 0.0.0.0 permit vlan 10 host permit vlan 10 host permit vlan 10 host host 00:00:00:00:00:00 count (0 packets) 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) NOTE: The output for port-channel interfaces does not display the physical interface.
PAGE 535
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. DellEMC# show ipv6 dhcp snooping IPv6 DHCP Snooping IPv6 DHCP Snooping Mac Verification : Enabled. : Disabled.
PAGE 536
Usage Information Example Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to associate the system with one or more DNS servers.
PAGE 537
Usage Information Example Version Description 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. DellEMC(conf)# ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 538
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrfname] name ip-address command.
PAGE 539
Defaults None Command Modes EXEC Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.
PAGE 540
14 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • • • ecmp-group hash-algorithm ip ecmp-group ip ecmp weighted link-bundle-monitor enable link-bundle-distribution trigger-threshold show config show link-bundle distribution ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
PAGE 541
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID.
PAGE 542
● xor1: Use CRC16_BISYNC_AND_XOR1 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor1 ● xor2: Use CRC16_BISYNC_AND_XOR2 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor2 ● xor4: Use CRC16_BISYNC_AND_XOR4 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor4 ● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR seed Defaults Enter the keyword seed and the seed value of the hash algorithm. The value ranges from 0 to 2147483646.
PAGE 543
default algorithm does not provide a satisfactory distribution of traffic, use the hash-algorithm command to designate another algorithm. When a Port Channel member leaves or is added to the Port Channel, the hash algorithm is recalculated to balance traffic across the members. ip ecmp-group Enable and specify the maximum number of ecmp that the L3 CAM hold for a route, By default, when maximum paths are not configured, the CAM can hold a maximum of 16 ecmp per route.
PAGE 544
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 545
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. link-bundle-distribution trigger-threshold Provides a mechanism to set the threshold to trigger when traffic distribution begins being monitored on an ECMP link bundle.
PAGE 546
Command Modes CONFIGURATION-ECMP-GROUP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 547
Po 100 DellEMC# Up 0 Equal Cost Multi-Path (ECMP) 547
PAGE 548
15 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: Topics: • • • • fips mode enable show fips status show ip ssh ssh fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 549
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 550
SSH server vrf : default. SSH server ciphers : aes256-ctr, aes256-cbc, aes192-ctr, aes192cbc, aes128-ctr, aes128-cbc, 3des-cbc. SSH server macs : hmac-sha2-256, hmac-sha1, hmac-sha1-96, hmac-md5, hmac-md5-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: DellEMC# show ip ssh SSH server : enabled. SSH server version : v2.
PAGE 551
● ● ● ● ● ● ● aes256–ctr: Force ssh to use the aes256–ctr encryption cipher. aes256–cbc: Force ssh to use the aes128–cbc encryption cipher. aes192–ctr: Force ssh to use the aes128–cbc encryption cipher. aes192–cbc: Force ssh to use the aes256–cbc encryption cipher. aes128–ctr: Force ssh to use the aes256–cbc encryption cipher. aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. 3des-cbc: Force ssh to use 3des-cbc encryption cipher.
PAGE 552
Usage Information Dell EMC Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. Example If FIPS mode is not enabled: DellEMC# ssh 10.10.10.
PAGE 553
16 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
PAGE 554
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 555
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 556
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol.
PAGE 557
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 558
Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration. Ownership is relinquished for a port only when the interface does not play a part in any control VLAN, that is, the interface does not belong to any ring. Related Commands ● show frrp — display the Resilient Ring Protocol configuration information. member-vlan Specify the member VLAN identification numbers.
PAGE 559
To reset the mode, use the no mode {master | transit} command. Parameters Defaults master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 560
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced This command places you into the resilient ring protocol.
PAGE 561
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
PAGE 562
● The number of state change counters Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command is executed.
PAGE 563
To remove the timer, use the no timer {hello-interval [milliseconds]}| {deadinterval milliseconds} command. Parameters hello-interval milliseconds dead-interval milliseconds Defaults Enter the keyword hello-interval then the time, in milliseconds, to set the hello interval of the control packets. The milliseconds must be entered in increments of 50 millisecond; for example, 50, 100, 150, and so on. If an invalid value is entered, an error message is generated. The range is from 50 to 2000 ms.
PAGE 564
17 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 565
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax Parameters clear gvrp statistics interface interface interface interface Defaults Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 566
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters Defaults config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 567
To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 568
NOTE: Designate the milliseconds in multiples of 100. Defaults As above. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 569
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 570
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 571
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series ● disable — globally disable GVRP. show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific.
PAGE 572
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 573
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 574
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. summary Defaults Enter the keyword summary to display just a summary of the GVRP statistics. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 575
Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 DellEMC# Related Commands ● show gvrp — display the GVRP configuration.
PAGE 576
18 High Availability (HA) High availability (HA) in the Dell EMC Networking OS is the configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol. You must specifically enable some protocols for HA.
PAGE 577
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the E-Series Enabling this command keeps the failed RPM in the failed state. If there are two RPMs in the system, enabling this command prevents the failed RPM from becoming a working Standby RPM. If there is only one RPM in the system, the failed RPM does not recover and affects the system. redundancy force-failover Force the secondary stack unit to become the primary stack unit.
PAGE 578
Parameters Default lacp Enter the keyword lacp to make LACP hitless. xstp Enter the keyword xstp to invoke hitless STP (all STP modes — MSTP, PVST+, RSTP, and STP). Disabled Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.
PAGE 579
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. The following describes the show redundancy command shown in the following example. Field Description RPM Status Displays the following information: ● Slot number of the RPM. ● Whether the RPM is Primary or Standby. ● The state of the RPM: Active, Standby, Booting, or Offline. ● Whether the link to the second RPM is up or down.
PAGE 580
-- RPM Redundancy Configuration ------------------------------------------------Primary RPM: rpm0 Auto Data Sync: Full Failover Type: Hot Failover Auto reboot RPM: Enabled Auto failover limit: 3 times in 60 minutes -- RPM Failover Record ------------------------------------------------Failover Count: 1 Last failover timestamp: Jul 13 2007 21:25:32 Last failover Reason: User request -- Last Data Block Sync Record: ------------------------------------------------Line Card Config: succeeded Jul 13 2007 21:28:5
PAGE 581
19 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 582
Table 4. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 582 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 583
20 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
PAGE 584
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 585
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 586
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. The access list accepted is an extended ACL.
PAGE 587
Version Description 7.7.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion.
PAGE 588
Version Description E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters Defaults seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 589
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 590
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 591
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax Parameters Defaults ip igmp version {2 | 3} 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. 2 (IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 592
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 593
Example Example (VLT) Field Description Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. DellEMC# show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.0.2 Vlan 100 00:00:05 00:02:04 225.0.0.3 Vlan 100 00:00:05 00:02:04 225.0.0.
PAGE 594
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 595
Internet address is 35.0.0.1/24 IGMP is enabled on interface IGMP query interval is 60 seconds IGMP querier timeout is 125 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is enabled for all groups IGMP activity: 0 joins IGMP querying router is 35.0.0.1 (this system) IGMP version is 2 Example (VRF) DellEMC# show ip igmp vrf BLUE interface GigabitEthernet 1/20 Inbound IGMP access group is not set Internet address is 50.10.4.
PAGE 596
Example Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 597
Important Points to Remember for IGMP Querier ● The IGMP snooping Querier supports version 2. ● You must configure an IP address to the VLAN interface for IGMP snooping Querier to begin. The IGMP snooping Querier disables itself when a VLAN IP address is cleared, and then it restarts itself when an IP address is reassigned to the VLAN interface. ● When enabled, IGMP snooping Querier does not start if there is a statically configured multicast router interface in the VLAN.
PAGE 598
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax debug ip igmp snooping [group address | interface] ● To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. ● To disable all debugging, use the undebug all command. Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 599
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 600
Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
PAGE 601
Usage Information On the C-Series and S-Series, unregistered multicast data traffic drops when you disable flooding; they do not forward the packets to multicast router ports. On the C-Series and S-Series, in order to disable Layer 2 multicast flooding, disable Layer 3 multicast (no ip multicast-routing). ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to GroupLeave messages.
PAGE 602
ip igmp snooping mrouter Statically configure a VLAN member port as a multicast router interface. Syntax ip igmp snooping mrouter interface interface To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 603
ip igmp snooping querier Enable IGMP querier processing for the VLAN interface. Syntax ip igmp snooping querier To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 604
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 605
Member Ports: Gi 1/17 DellEMC# show ip igmp snooping mrouter Display multicast router interfaces. Syntax Parameters show ip igmp snooping mrouter [vlan number] vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 606
21 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • • Basic Interface Commands Egress Interface Selection (EIS) Commands Port Channel Commands Time Domain Reflectometer (TDR) Commands UDP Broadcast Commands Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 607
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. vrrp [ipv6 {vr-id} (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To | vr-id] clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
PAGE 608
Related Commands ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear counters eee Clear the counters for EEE on all copper ports or specific ports. Syntax clear counters [interface—type [slot/port | slot/port-range]] eee Parameters interface-type Enter the interface information as GigabitEthernet or TenGigabitEthernet followed by the slot and the port number or range of port numbers.
PAGE 609
Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 610
Usage Information By default, a combo port is in Hybrid mode. Use the combo-port-type command to provision the combo port as either copper or fiber. Use the no combo-port-type command to change the combo port to Hybrid mode. The negotiation auto command is not available on the combo ports in the hybrid mode. You need to provision the combo port as copper or fiber medium using the combo-port-type command.
PAGE 611
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. With each flap, Dell EMC Networking OS penalizes the interface by assigning a penalty (1024) that decays exponentially depending on the configured half-life. After the accumulated penalty exceeds the suppress threshold value, the interface moves to the Error-Disabled state. This interface state is deemed as “down” by all static/dynamic Layer 2 and Layer 3 protocols.
PAGE 612
no assigned IP address or switchport (no ip address). This command removes all software settings and all L3, VLAN, VXLAN, and port-channel configurations on a physical interface.
PAGE 613
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Modified for E-Series: Revised from 78 to 240 characters. Important Points to Remember: ● To use special characters as a part of the description string, you must enclose the whole string in double quotes.
PAGE 614
encapsulation dot1q Configures lite-subinterfaces. Syntax encapsulation dot1q vlan-id To remove a previously configured lite-subinterface, use the no encapsulation dot1q vlan-id command. Parameters dot1q vlan-id Enter the keyword dot1q followed by the VLAN ID to which the host belongs. The range is from 1 to 4094. A lite subinterface is considered as a Layer 3 port property and is synchronous with the existing rules of applying Layer 2 or Layer 3 properties to an interface.
PAGE 615
Version Description 9.14(1.0) Introduced arp-inspection option. 9.14(0.0) Introduced on the platforms S4048–ON, S6100–ON, Z9100–ON, S4048T-ON, S3048–ON, S6000, S6010–ON, S5048F-ON, FN-IOM and MXL. 9.13(0.2P2) Introduced on the S3100. Usage Information This command has to be configured before the interface moves to Err-disabled state. If not, the recovery action is not performed. Related Commands errdisable recovery interval— Configure recovery timer interval for an interface.
PAGE 616
NOTE: Flow-control packets are mirrored only when flow-control rx is enabled on an interface. Defaults rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received. tx off Enter the keywords tx off so that flow control frames are not sent from this port to the connected device when a higher rate of traffic is received.
PAGE 617
When a port receives traffic at a higher rate than it can process, the frames are stored in the port buffer. As a result, buffer usage increases. When the buffer usage reaches the value specified in the “pause-threshold” argument, the port sends PAUSE frame to the connected link partner to stop sending the traffic. Eventually this reduces the buffer usage. When the buffer usage drops by the value specified in the “resume-threshold”, the port again sends a PAUSE frame with 0 as wait-time.
PAGE 618
off off on off on off off off off on on on off off on on off off on on off on on on off off on on off off on on off off on on off off on on interface Configure a physical or virtual interface on the switch. Syntax interface interface Parameters Defaults interface Enter one of the following keywords and the interface information: ● For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0.
PAGE 619
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport.
PAGE 620
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 621
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 622
Usage Information Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a Management port. The Management port is enabled by default (no shutdown).
PAGE 623
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete the Null interface. The only configuration command possible in a Null interface is ip unreachables. Example Related Commands DellEMC(conf)# interface null 0 DellEMC(conf-if-nu-0)# ● ● ● ● ● interface — configure a physical interface.
PAGE 624
Usage Information Version Description 9.13(0.0) Introduced the Configuration Terminal Batch mode on C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P2) Introduced on the S4038-ON. 9.8(0.0P5) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 625
Example (Multiple Ports) Example (Overlapping Ports) Usage Information DellEMC(conf)# interface range gigabitethernet 2/10 - 2/23, gigabitethernet 2/12 - 2/17 DellEMC(conf-if-range-gi-2/10-2/23)# DellEMC(conf)# interface range gigabitethernet 2/3 - 2/11, gigabitethernet 2/3 - 2/23 DellEMC(conf-if-range-gi-2/3-2/23)# Only VLAN and port-channel interfaces created using the interface vlan and interface portchannel commands can be used in the interface range command.
PAGE 626
Dec 6 10:43:18 %RPM1-P:CP %CLIBATCH-6-CLI_BATCH_CONFIG_COMPLETE_TRAP: Batch configuration commit is success Related Commands ● ● ● ● ● interface port-channel — configure a port channel group. interface vlan — configure a VLAN interface. show config (from INTERFACE RANGE mode) — display the bulk configuration interfaces. show range — display the bulk configuration ranges. interface range macro (define) — define a macro for an interface-range.
PAGE 627
Example (Single Range) Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This example shows how to define an interface range macro named test. Execute the show runningconfig command to display the macro definition.
PAGE 628
Example (Single Range) Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced This example shows the macro named test that was defined earlier. DellEMC(config)# interface range macro test DellEMC(config-if-range-gi-1/1-3,gi-5/1-47,gi-2/1-89)# Dell Related Commands ● interface range — configure a range of command (bulk configuration).
PAGE 629
FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs and IP ACLs are supported. For more information, see Access Control Lists (ACL). The following features are not supported on VLANs associated with an OpenFlow instance: ● IPv4 ● IPv6 ● MTU If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously.
PAGE 630
Usage Information Version Description pre-Version 6.1.1.0 Introduced on the E-Series. When you configure keepalive, the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive, the system does not send keepalive packets and so the local end of a WAN link remains up even if the remote end is down. negotiation auto Enable auto-negotiation on an interface.
PAGE 631
If you do not use the mode option, the default setting is slave. If you do not configure forced-master or forced-slave on a port, the port negotiates to either a master or a slave state. Port status is one of the following: ● Forced-master ● Force-slave ● Master ● Slave ● Auto-neg Error — typically indicates that both ends of the node are configured with forced-master or forced-slave. CAUTION: Ensure that one end of your node is configured as forced-master and one is configured as forced-slave.
PAGE 632
● ● ● ● auto-negotiation auto-negotiation auto-negotiation auto-negotiation enabled speed 100 disabled speed 100 enabled speed 100 disabled speed 100 Link Status Between Port 1 and Port 2 ● Up at 1000 Mb/s ● Up at 100 Mb/s ● Up at 100 Mb/s ● Down ● Down * You cannot disable auto-negotiation when the speed is set to 1000 or auto. monitor interface Monitor counters on a single interface or all interfaces. The screen is refreshed every five seconds and the CLI prompt disappears.
PAGE 633
Usage Information Example (Single Interface) Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. In the Example, the delta column displays changes since the last screen refresh. The following are the monitor command menu options.
PAGE 634
Output throttles: m l T q Example (All Interfaces) - 0 Change mode Page up Increase refresh interval Quit 0 pps 0 c - Clear screen a - Page down t - Decrease refresh interval systest-3 Monitor time: 00:01:31 Refresh Intvl.
PAGE 635
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 636
portmode hybrid To accept both tagged and untagged frames, set a physical port or port-channel. A port configured this way is identified as a hybrid port in report displays. Syntax portmode hybrid To return a port to accept either tagged or untagged frames (non-hybrid), use the no portmode hybrid command. Defaults non-hybrid Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 637
DellEMC(conf-if-vl-20)# tagged gigabitethernet 1/1 DellEMC(conf-if-vl-20)# Example Example (Vlan) DellEMC(conf-if-vl-20)# do show interfaces switchport Name: GigabitEthernet 1/1 802.
PAGE 638
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced The output of the show interfaces command displays the configured rate interval, along with the collected traffic data. rate-interval (Configuration Mode) Configure the traffic sampling interval for all physical and logical port-channel interfaces globally.
PAGE 639
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 640
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 641
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - IPV4 L3 Unicast Frame Counter IPV4 L3 Routed Multicast Packets IPV6 L3 Unicast Frame Counter IPV6 L3 Routed Multicast Packets Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024
PAGE 642
TX - VLAN Tag Frame Counter TX - Double VLAN Tag Frame Counter TX - RUNT Frame Counter TX - Fragment Counter TX - PFC Frame Priority 0 TX - PFC Frame Priority 1 TX - PFC Frame Priority 2 TX - PFC Frame Priority 3 TX - PFC Frame Priority 4 TX - PFC Frame Priority 5 TX - PFC Frame Priority 6 TX - PFC Frame Priority 7 TX - Debug Counter 0 TX - Debug Counter 1 TX - Debug Counter 2 TX - Debug Counter 3 TX - Debug Counter 4 TX - Debug Counter 5 TX - Debug Counter 6 TX - Debug Counter 7 TX - Debug Counter 8 TX - D
PAGE 643
RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - PFC Frame Priority 7 Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter 8 EEE LPI Event Counter EEE LPI Duration Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023
PAGE 644
Parameters interface Enter one of the following keywords and the interface information: ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For stack-units, enter the keywords stack-unit then the slot/port information. ● For a Null interface, enter the keyword null then the Null interface number. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 645
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.2) Added support for the tunnel interface type. 9.1(0.0) Updated Management Ethernet output to include two global IPv6 addresses on S4810 and Z9000 and added output example showing OpenFlow instance ID. 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. 8.3.11.4 Output expanded to support eSR4 optics in Z9000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 646
Example 646 Interfaces Line Description Energy Efficient Ethernet Displays whether Energy Efficient Ethernet has been enabled or not. ARP type:... Displays the ARP type and the ARP timeout value for the interface. Last clearing... Displays the time when the show interfaces counters where cleared. Queuing strategy... States the packet queuing strategy. FIFO means first in first out.
PAGE 647
Last clearing of "show interface" counters 3d17h53m Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts
PAGE 648
Usage Information Example Example (Management Ethernet) Example (Management Ethernet, two IPv6 addresses) The Management port is enabled by default (no shutdown). If necessary, use the ip address command to assign an IP address to the Management port. If two RPMs are installed in your system, use the show redundancy command to display which RPM is the Primary RPM.
PAGE 649
Pluggable media not present Interface index is 302006472 Internet address is 10.16.130.
PAGE 650
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.
PAGE 651
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms.
PAGE 652
Example Related Commands DellEMC# show interfaces dampening Interface Supp Flaps Penalty Half-Life Reuse Suppress Max-Sup State Gi 1/2 Up 0 0 20 800 4500 120 Gi 1/10 Up 0 0 5 750 2500 20 DellEMC# ● dampening — configure dampening on an interface. ● show interfaces configured — display any interface with a non-default configuration. show interfaces eee Display whether EEE is enabled on interfaces..
PAGE 653
GigabitEthernet 1/20 GigabitEthernet 1/21 GigabitEthernet 1/22 GigabitEthernet 1/23 GigabitEthernet 1/24 TenGigabitEthernet 1/25 TenGigabitEthernet 1/26 Yes Yes Yes Yes Yes N/A N/A down down down down down down down Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto <> Example for a specific interface: S3100 Series DellEMC#show interfaces gigabitethernet 1/1 eee Interface EEE Status Speed GigabitEthernet 1/1 Yes down Auto Related Commands Duplex Auto ● show interf
PAGE 654
0 Gi 1/4 0 Gi 1/5 0 Gi 1/6 0 Gi 1/7 0 Gi 1/8 0 Gi 1/9 0 Gi 1/10 0 Gi 1/11 0 Gi 1/12 0 Gi 1/13 0 Gi 1/14 0 Gi 1/15 0 Gi 1/16 0 Gi 1/17 0 Gi 1/18 0 Gi 1/19 0 Gi 1/20 0 Gi 1/21 0 Gi 1/22 0 Gi 1/23 0 Gi 1/24 0 Te 1/25 Te 1/26 Te 1/27 0 Te 1/28 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes Yes 0 0 0 Yes
PAGE 655
show interfaces phy Display auto-negotiation and link partner information. Syntax Parameters show interfaces gigabitethernet slot/port phy gigabitethernet Enter the keyword gigabitethernet then the slot/port information. tengigabitethern et Enter the keyword tengigabitethernet then the slot or port information. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 656
AutoNegotiation Displays the control words the remote interface advertises during negotiation. Remote Partner’s Duplex is either half or full. Asym- and Sym Pause is the types of flow control Ability the remote interface supports. AutoNegotiation Expansion ParallelDetectionFault is the handshaking scheme in which the link partner continuously transmit an “idle” data packet using the Fast Ethernet MLT-3 waveform.
PAGE 657
ParallelDetectionFault: False ... show interfaces stack-unit Display information on all interfaces on a specific S-Series or Z-Series stack member. Syntax Parameters show interfaces stack-unit unit-number unit-number Enter the stack member number. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 658
0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 659
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 660
between 1 and 4, specify the port range as show interfaces interfacetype 1/1 - 4. ● For port–channel interfaces, you can specify multiple ports as port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces port— channel 1 - 4. stack-unit unit-id (OPTIONAL) Enter the keywords stack-unit then the stack member number. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 661
Example DellEMC# show interfaces switchport Name: GigabitEthernet 1/1 802.1QTagged: Hybrid Vlan membership: Vlan 2, Vlan 20 Native VlanId: 20 Name: GigabitEthernet 1/2 802.1QTagged: True Vlan membership: Vlan 2 Name: GigabitEthernet 1/3 802.1QTagged: True Vlan membership: Vlan 2 Name: GigabitEthernet 1/4 802.1QTagged: True Vlan membership: Vlan 2 --More-- Related Commands ● interface — configure a physical interface on the switch. ● show ip interface — display Layer 3 information about the interfaces.
PAGE 662
Usage Information Version Description 9.11(0.0) Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000-ON, S6100, Z9500, S6010, and Z9100. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 663
Line Description Voltage Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 664
Line Description is set to true. If it falls below the low alarm/warning thresholds, the Rx power low alarm/warning flag is set to true. Data Ready state This field indicates that the transceiver has achieved power up and data is ready. Bar This is set to true if data is ready to be sent and set to false if data is being transmitted. Rx LOS state This is the digital state of the Rx_LOS output pin. This is set to true if the operating status is down.
PAGE 665
Example Line Description Tx Bias Low Warning Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power Low Warning Flag This can be either true or false, depending on the Current Tx power value displayed above. Rx Power Low Warning Flag This can be either true or false, depending on the Current Rx power value displayed above. DellEMC# show interfaces GigabitEthernet 1/1 transceiver SFP is present.
PAGE 666
SFP 1 Rx LOS state = True SFP 1 Tx Fault state = False SFP 1 Rate Select state = False SFP 1 RS state = False SFP 1 Tx Disable state = False =================================== SFP 1 Temperature High Alarm Flag = False SFP 1 Voltage High Alarm Flag = False SFP 1 Tx Bias High Alarm Flag = False SFP 1 Tx Power High Alarm Flag = False SFP 1 Rx Power High Alarm Flag = False SFP 1 Temperature Low Alarm Flag = False SFP 1 Voltage Low Alarm Flag = False SFP 1 Tx Bias Low Alarm Flag = False SFP 1 Tx Power Low Alarm
PAGE 667
Example DellEMC# show interfaces vlan 10 Vlan 10 is up, line protocol is down Address is 90:b1:1c:f4:99:ce, Current address is 90:b1:1c:f4:99:ce Interface index is 1107787786 Internet address is not set Mode of IPv4 Address Assignment: NONE DHCP Client-ID: 90b11cf499ce MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 2d17h26m Queueing strategy: fifo Time since last interface status change: 2d17h26m Input Statistics: 0 packets,
PAGE 668
Related Commands ● interface — configure a physical interface on the switch. ● show ip interface — display Layer 3 information about the interfaces. show running-config ecmp-group Display interfaces, LAG, or LAG link bundles being monitored for uneven traffic distribution using the ecmp-group monitoring enable command. The ECMP group could have a LAG or a list of interfaces (not just LAG link-bundles). Syntax show running-config ecmp-group Defaults Disabled.
PAGE 669
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The shutdown command marks a physical interface as unavailable for traffic. To discover if an interface is disabled, use the show ip interface brief command.
PAGE 670
Defaults auto Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14.1.2 Introduced the option 10000 speed setting on the S5048F-ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Added support for fanned–out 1 Gigabit SFP port. 9.8(2.0) Introduced on the S3100 series. 9.8(0.
PAGE 671
speed (Management interface) Set the speed for the Management interface. Syntax speed {10 | 100 | 1000 | auto} To return to the default setting, use the no speed command. Parameters Defaults 10 Enter the keyword 10 to set the interface’s speed to 10 Mb/s. 100 Enter the keyword 100 to set the interface’s speed to 100 Mb/s. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s. auto Enter the keyword auto to set the interface to auto-negotiate its speed.
PAGE 672
To remove an interface from Layer 2 mode and place it in Layer 3 mode, enter the no switchport command. If a switchport backup interface is configured, first remove the backup configuration. To remove a switchport backup interface, enter the no switchport backup interface command. Parameters backup (OPTIONAL) Use this option to configure a redundant Layer 2 link without using Spanning Tree.
PAGE 673
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output.
PAGE 674
Egress Interface Selection (EIS) Commands The following commands are Egress Interface Selection (EIS) commands. application Configure the management egress interface selection. Syntax application {all | application-type} To remove a management application configuration, use the no application {all | application-type} command. Parameters Defaults application-type Enter any of the following keywords: ● For DNS, enter the keyword dns. ● For FTP, enter the keyword ftp. ● For NTP, enter the keyword ntp.
PAGE 675
To remove a management application configuration, use the no application {all | application-type} command. Parameters Defaults application-type Enter any of the following keywords: ● For HTTP, enter the keyword http. ● For ICMP, enter the keyword icmp. all Configure all applications. None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 676
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T. management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface.
PAGE 677
Example Version Description 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T. DellEMC# show ip management-eis-route Destination Gateway ----------------10.11.0.0/16 ManagementEthernet 1/1 172.16.1.0/24 10.11.192.4 State ----Connected Active Route Source -----------Connected Static show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Syntax show management application pkt-cntr Defaults None.
PAGE 678
Example Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 679
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 680
group Group two LAGs in a supergroup (“fate-sharing group” or “failover group”). Syntax group group_number port-channel number port-channel number To remove an existing LAG supergroup, use the no group group_number command. Parameters group_number Enter an integer from 1 to 32 that uniquely identifies this LAG fate-sharing group. port-channel Enter the keywords port-channel then an existing LAG number. Enter this keyword/variable combination twice, identifying the two paired LAGs.
PAGE 681
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the number of port channels to 4096. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 682
minimum-links Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the LAG to be also in “oper up” status. Syntax minimum-links number Parameters Defaults number Enter the number of links in a LAG that must be in “oper up” status. The range is from 1 to 16. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 683
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 684
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. DellEMC(conf-if-po-1)# show config ! interface Port-channel 1 no ip address shutdown DellEMC(conf-if-po-1)# show interfaces port-channel Display information on configured Port Channel groups.
PAGE 685
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Modified to display the LAG failover group status. 7.5.1.0 Introduced on the C-Series.
PAGE 686
Example DellEMC# show interfaces port-channel 20 Port-channel 20 is up, line protocol is up (Failover-group 1 is down) Hardware address is 00:01:e8:01:46:fa Port-channel is part of failover-group 1 Internet address is 1.1.120.
PAGE 687
show port-channel-flow Display an egress port in a given port-channel flow. Syntax Parameters show port-channel-flow outgoing-port-channel number incoming-interface interface {source-ip address destination-ip address} | {source-port number destination-port number} | {source-mac address destination-mac address {vlan vlanid | ether-type}} outgoing-portchannel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information.
PAGE 688
Usage Information Version Description 8.3.10.0 Introduced on the S4810. Because this command calculates based on a Layer 2 hash algorithm, use this command to display flows for switched Layer 2 packets, not for routed packets (use the show ip flow command to display routed packets). The show port-channel-flow command returns the egress port identification in a given portchannel if a valid flow is entered.
PAGE 689
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7.0.0 Introduced on the S5000. 8.3.19.
PAGE 690
Usage Information Version Description 9.7.0.0 Introduced on the S5000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.1.1.0 Introduced. If the TDR test has not been run, an error message is generated: %Error: Please run the TDR test first The following describes the TDR test status.
PAGE 691
debug ip udp-helper Enable UDP debug and display the debug information on a console. Syntax debug ip udp-helper To disable debug information, use the no debug ip udp-helper command. Defaults Debug disabled. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 692
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series ExaScale. Usage Information When a UDP broadcast packet is flooded out of an interface, and the outgoing interface is configured using this command, the outgoing packet’s IP destination address is replaced with the configured broadcast address. Related Commands debug ip udp-helper — enables debug and displays the debug information on a console.
PAGE 693
● show ip udp-helper — display the configured UDP helpers on all interfaces. show ip udp-helper Display the configured UDP helpers on all interfaces. Syntax show ip udp-helper Defaults None Command Modes EXEC Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series.
PAGE 694
22 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: ● Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 695
● md5 — Use Message Digest 5 (MD5) authentication. ● sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. ● null — Causes an encryption policy configured for the area to not be inherited on the interface. Defaults espauthentication Enter the keywords esp-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. ● md5 — Use Message Digest 5 (MD5) authentication.
PAGE 696
To delete a crypto policy entry, use the no crypto ipsec policy name seq-num ipsecmanual command. Parameters Defaults name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 697
match Apply an match filter to the crypto policy. Syntax match seq-num tcp [sourceip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] To remove the match filter for the crypto map, use the no match seq-num tcp [source ip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] command. Parameters seq-num Enter the match command sequence number.
PAGE 698
session-key Specify the session keys used in the crypto policy entry. Syntax session-key {inbound | outbound} {ah spi hex-key-string | esp spi encrypt hex-key-string auth hex-key-string To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters Defaults name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec.
PAGE 699
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500.
PAGE 700
Outbound ESP Auth SPI : Outbound ESP Encry SPI: Outound AH Key : Outound ESP Auth Key : Outound ESP Encry Key : Match sequence Num Protocol type IP or IPv6 Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num 0 0 [0]:: [0]:: [0]:: : : : : : : : : : : : 2 tcp IP 1.1.1.1 /32 0 1.1.1.2 /32 23 DellEMC(conf-crypto-policy)# transform-set Specify the transform set the crypto policy uses.
PAGE 701
23 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 702
• • • • • show show show show show ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters Defaults vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 703
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid. You can use the vrf attribute of this command to create a static ARP entry on either a default or a non-default VRF.
PAGE 704
Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands ● show arp retries — display the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
PAGE 705
Parameters Defaults vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows. max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 706
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart. Related Commands ● show arp retries — display the configured number of ARP retries. arp timeout Set the time interval for an ARP entry to remain in the ARP cache.
PAGE 707
Version Description pre-6.2.1.1 Introduced on the E-Series. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM). Syntax Parameters clear arp-cache [vrf vrf-name | interface | ip ip-address] [no-refresh] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear the ARP cache corresponding to that VRF.
PAGE 708
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 709
clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.) Syntax Parameters clear ip fib stack-unit unit-number vrf vrf-name unit-number Enter the number of the stack unit. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all FIB entries corresponding to that VRF. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 710
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 711
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 712
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 713
Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 714
debug ip icmp View information on the internal control message protocol (ICMP). Syntax debug ip icmp [interface] [count value] To disable debugging, use the no debug ip icmp command. Parameters interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 715
Example Usage Information ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.40 echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.40 reply reply reply reply To stop packets from flooding the user terminal when debugging is turned on, use the count option.
PAGE 716
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Added the access-group option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option. The following describes the debug ip packet command in the following example.
PAGE 717
IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable ICMP type=8, code=0 Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option. The access-group option supports only the equal to (eq) operator in TCP ACL rules. Port operators not equal to (neq), greater than (gt), less than (lt), or range are not supported in access-group option (refer to the following example).
PAGE 718
Parameters Defaults ip-address Enter an IP address in dotted decimal format. mask Enter the mask of the IP address in slash prefix format (for example, /24). secondary (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 719
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 720
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To configure a list of possible domain names, configure the ip domain-list command up to six times. If you configure both the ip domain-name and ip domain-list commands, the software tries to resolve the name using the ip domain-name command.
PAGE 721
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To fully enable DNS, also specify one or more domain name servers with the ip name-server command. Dell EMC Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out all other interfaces, including the Management port.
PAGE 722
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You can only configure one domain name with the ip domain-name command. To configure more than one domain name, configure the ip domain-list command up to six times.
PAGE 723
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. You can add multiple DHCP servers by entering the ip helper-address command multiple times. If multiple servers are defined, an incoming request is sent simultaneously to all configured servers and the reply is forwarded to the DHCP client.
PAGE 724
Version Description 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced for the E-Series. Usage Information This command disables the incrementing of the hops field when boot requests are relayed to a DHCP server through Dell EMC Networking OS. If the incoming boot request already has a non-zero hops field, the message is relayed with the same value for hops. However, the message is discarded if the hops field exceeds 16, to comply with the relay agent behavior specified in RFC 1542.
PAGE 725
ip icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv4 packets.
PAGE 726
address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output. The loopback address must be unique in a particular domain.
PAGE 727
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 728
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series.
PAGE 729
ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command. Parameters Defaults ipv4-address Enter the IPv4 address, in dotted decimal format, of the name server to be used. ipv4-address2...
PAGE 730
ip proxy-arp Enable proxy ARP on an interface. Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 731
Parameters vrf vrf-name (Optoinal) Enter the keyword vrf and then the name of the VRF to configure a static route corresponding to that VRF. Use this VRF option after the ip route keyword to configure a static route on that particular VRF. destination Enter the IP address in dotted decimal format of the destination device. mask Enter the mask in the slash prefix format (/x) of the destination IP address. ip-address Enter the IP address of the forwarding router in dotted decimal format.
PAGE 732
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Included the weighted parameter to support weighted ECMP feature. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 733
DellEMC(conf)# do show running-config | grep route ip route 1.1.1.0/24 4.4.4.2 weight 100 ip route 1.1.1.0/24 6.6.6.2 weight 200 DellEMC(conf)# ip route vrf test 1.1.1.0/24 4.4.4.2 weight 100 DellEMC(conf)# ip route vrf test 1.1.1.0/24 6.6.6.2 weight 200 DellEMC(conf)# DellEMC(conf)# do show running-config | grep route ip route vrf test 1.1.1.0/24 4.4.4.2 weight 100 ip route vrf test 1.1.1.0/24 6.6.6.2 weight 200 Related Commands ● show ip route — view the switch routing table.
PAGE 734
ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages. Syntax ip unreachables To disable the generation of ICMP messages, use the no ip unreachables command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 735
Parameters Defaults ip-selection {dest-ip | source-ip} Enter the keywords to distribute IP traffic based on the following criteria: ● dest-ip — Uses destination IP address and destination port fields to hash. The hashing mechanism returns a 3-bit index indicating which port the packet should be forwarded. ● source-ip — Uses source IP address and source port fields to hash. The hashing mechanism returns a 3-bit index indicating which port the packet should be forwarded.
PAGE 736
● ● ● ● ● ● IP source address IP destination address VLAN Protocol TCP/UDP source port TCP/UDP destination port load-balance hg Choose the traffic flow parameters the hash calculation uses while distributing the traffic across internal higig links.
PAGE 737
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 738
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 739
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ip ip-address mask (OPTIONAL) Enter the keyword ip then an IP address in the dotted decimal format. Enter the optional IP address mask in the slash prefix format (/ x).
PAGE 740
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. The following example shows two VLANs that are associated with a private VLAN (PVLAN) (refer to Private VLAN (PVLAN)). If you have entered the clear arp-cache command to remove a large number of ARP entries and the command is still being processed in the background, an error message display if you attempt to enter the show arp command: Clear arp in-progress.
PAGE 741
Description Example (Summary) Static Entries Lists the total number of configured or static ARP entries. Dynamic Entries Lists the total number of learned or dynamic ARP entries. CPU Lists which CPU the entries are stored on. DellEMC# show arp summary TotalEntries Static Entries Dynamic Entries CPU ---------------------------------------------83 0 83 CP DellEMC# Related Commands ● ip local-proxy-arp — enable/disable Layer 3 communication in secondary VLANs.
PAGE 742
show hosts View the host table and DNS configuration. Syntax show hosts Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 743
Field Description ● ?? — the entry is suspect. Example Related Commands TTL Displays the amount of time until the entry ages out of the cache. For dynamically learned entries only. Type Displays IP as the type of entry. Address Displays the IP addresses assigned to the host.
PAGE 744
● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 745
1.1.1.0/24 100.1.1.0/24 100.1.1.0/24 0.0.0.
PAGE 746
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for up to seven stack members. 7.6.1.0 Introduced on the S-Series. The following describes the show ip fib stack-unit command shown in the following example. Field Description Destination Lists the destination IP address. Gateway Displays either the word “direct” and an interface for a directly connected route or the remote IP address used to forward the traffic.
PAGE 747
Parameters interface interface source-ip address destination-ip Enter the keyword interface then one of the following interface keywords. ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Enter the keywords source-ip then the IP source address in IP address format.
PAGE 748
Example DellEMC# show ip flow interface Gi 2/42 20.1.1.1 100.1.1.2 protocol tcp Flow: 20.1.1.1 100.1.1.2 6 Ingress interface: Gi 2/42 Egress Interface: Gi 2/43 DellEMC# show ip interface View IP-related information on all interfaces. Syntax show ip interface [interface | brief] [configured] Parameters interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 749
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.2 Supported on the E-Series E600i. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 750
Fields Description Interface Displays type of interface and the associated slot and port number. IP-Address Displays the IP address for the interface, if configured. Ok? Indicates if the hardware is functioning properly. Method Displays “Manual” if the configuration is read from the saved configuration. Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface.
PAGE 751
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Example show ipv6 management-route Display the IPv6 static routes configured for the management interface.
PAGE 752
Example DellEMC# show ipv6 IPv6 Destination ---------------2001:34::0/64 2001:68::0/64 DellEMC# management-route Gateway ------ManagementEthernet 1/1 2001:34::16 State ----Connected Active show ip protocols View information on all routing protocols enabled and active on the switch. Syntax show ip protocols Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 753
Address : 20.20.20.2 Filter-list in : foo Route-map in : foo Weight : 0 Address : 5::6 Weight : 0 DellEMC# show ip route View information, including how they were learned, about the IP routes on the switch.
PAGE 754
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 755
Field Description If weighted ECMP is disabled, the show ip route command does not show the weighted ECMP route information. Example Destination Identifies the route’s destination IP address Gateway Identifies whether the route is directly connected and on which interface the route is configured. Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured.
PAGE 756
C Example (With Weighted ECMP Enabled) ----------13.0.0.0/24 ----------------- ----------Direct, Gi 1/17 0/0 00:00:04 DellEMC(conf)# ip route 1.1.1.0/24 6.6.6.2 weight 100 DellEMC(conf)# ip route 1.1.1.0/24 6.6.6.
PAGE 757
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 758
show ip route summary View a table summarizing the IP routes in the switch. Syntax show ip route [vrf vrf-name] [summary] Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on the IP routes corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 758 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 759
Example Column Heading Description Total 1388 active... Displays the number of active and non-active routes and the memory usage of those routes. If there are no routes configured in the Dell EMC Networking OS, this line does not appear.
PAGE 760
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 F10 Monitoring MIB available for the ip traffic statistics command. pre-6.1.1.0 Introduced on the E-Series.
PAGE 761
● ● ● ● Example ARP ARP ARP ARP Statistics: Statistics: Statistics: Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3 Sent: Request: Object = f10ArpReqSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.2 Sent: Replies: Object = f10ArpReplySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.4 Sent: Proxy: Object = f10ArpProxySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.
PAGE 762
Usage Information 762 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 6.4.1.0 Introduced The following describes the show tcp statistics cp command shown in the following example.
PAGE 763
Example Field Description 7 Connections initiated... Displays the number of TCP connections initiated, accepted, and established. 14 Connections closed... Displays the number of TCP connections closed, dropped. 20 Total rxmt... Displays the number of times the switch tried to re-send data and the number of connections dropped during the TCP retransmit timeout period. 0 Keepalive....
PAGE 764
24 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 765
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 766
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 767
-- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 768
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Added the monitor option.
PAGE 769
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 770
Defaults deny Enter the keyword deny to configure a filter to drop packets meeting this condition. ospfv3 Specify that this ACL is for OSPFv3 control plane traffic All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 771
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 772
cam-acl Allocate space for IPv6 ACLs. Syntax cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} Parameters default Use the default CAM profile settings, and set the CAM as follows: ● L3 ACL (ipv4acl): 6 ● L2 ACL(l2acl): 5 ● IPv6 L3 ACL (ipv6acl): 0 ● L3 QoS (ipv4qos): 1 ● L2 QoS (l2qos): 1 l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 773
25 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 774
Command Modes CONFIGURATION Command History Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048–ON. 9.8(0.0P2) Introduced on the S3048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can partition the LPM table to store IPv6 prefixes greater than /64 mask length.
PAGE 775
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax Parameters clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 776
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have.
PAGE 777
ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface. Syntax ipv6 address autoconfig To disable the address autoconfig operation on the management interface, use the no ipv6 address autoconfig command. Default Disabled Command Modes INTERFACE (management interface only) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 778
Defaults None Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1(0.0) Updated Usage Information. 9.0.0.
PAGE 779
ipv6 address eui64 Configure IPv6 EUI64 address configuration on the interface. Syntax ipv6 address {ipv6-address prefix-length} eui64 To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address {ipv6-address prefix-length} eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 780
Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 781
To remove an IP host, use the no ipv6 host name {ipv6–address}. Parameters Defaults name Enter a text string to associate with one IP address. ipv6-address Enter the IPv6 address (X:X:X:X::X) to be mapped to the name. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 782
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series. You can separately configure both IPv4 and IPv6 domain name servers. In a dual stack setup, the system sends both A (request for IPv4 — RFC 1035) and AAAA (request for IPv6 — RFC 3596) record requests to a DNS server even if only the ip name-server command is configured.
PAGE 783
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.1 Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S4810, S4820, S5000, S6000, S6010–ON, S6000–ON, S6100–ON, Z9100–ON, C9010, Z9500, MXL, and FN IOM. ipv6 nd dns-server Configures Recursive DNS Server (RDNSS) addresses to be distributed via IPv6 router advertisements to an IPv6 device.
PAGE 784
ipv6 nd prefix Specify which IPv6 prefixes are included in Neighbor Advertisements. Syntax ipv6 nd prefix {ipv6-prefix | prefix-length | default} [no-advertise] | [no-autoconfig] [no-rtr-address] [off-link] [lifetime {valid | infinite} {preferred | infinite}] Parameters ipv6-prefix Enter an IPv6 prefix. prefix-length Enter the prefix then the prefix length. The length range is from 0 to 128. default Enter the keyword default to set default parameters for all prefixes.
PAGE 785
ipv6 nd reachable-time Configure the amount of time before an IPv6 neighbor is considered unreachable. Syntax ipv6 nd reachable-time reachable-time To restore to default, use the no ipv6 nd reachable-time command. Parameters Default reachable-time Enter the reachable time in milliseconds. The value is from 0 to 3600000. The default value is 0. Disabled Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 786
Configure the IPv6 route using a next-hop IPv6 address in order for the ping command to detect the destination address. ipv6-address (OPTIONAL) Enter the forwarding router IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. distance (OPTIONAL) Enter a number as the metric distance assigned to the route. The range is from 1 to 255. name description (OPTIONAL) Enter the keyword name and the description for the IPv6 static route configuration.
PAGE 787
Dell EMC Networking OS withdraws the route. The route is re-installed, by Dell EMC Networking OS, when the recursive resolution is satisfied. After an IPv6 static route interface is created, if an IP address is not assigned to a peer interface, the peer must be manually pinged to resolve the neighbor information. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect.
PAGE 788
Usage Information Because this command is enabled by default, it does not appear in the running configuration. When you disable unicast routing, the no ipv6 unicast-routing command is included in the running configuration. Whenever unicast routing is disabled or re-enabled, DellEMC Networking OS generates a syslog message indicating the action.
PAGE 789
Version Description 8.3.7.1 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. Usage Information NOTE: If a route has a mask greater than 64, no output is displayed and no output is displayed for show ipv6 cam stack-unit unit-number port-set {0-1} ipv6-address, but an equivalent /64 entry would be listed in the show ipv6 cam stack-unit unit-number port-set {0-1} output.
PAGE 790
slot-number Enter the number of the stack unit. summary (OPTIONAL) Enter the keyword summary to view a summary of entries in IPv6 cam. ipv6-address Enter the IPv6 address in the x:x:x:x::x/n format to display networks that have more specific prefixes. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 791
Related Commands Version Description 8.3.7.0 Introduced on the S4810. ● ipv6 nd dad attempts — configure system to set the flow label field in the packets to zero. show ipv6 interface Display the status of interfaces configured for IPv6.
PAGE 792
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Added support for IPv6 recursive DNS addresses on the Z9500. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Added support for tunnel interface. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.2.1 Introduced on the S-Series. 8.2.1.
PAGE 793
ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 27550 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 IPv6 unicast RPF check is not supported DellEMC# DellEMC# show ipv
PAGE 794
GigabitEthernet 1/12 fe80::201:e8ff:fea7:497e 100::2/64 ManagementEthernet 1/1 fe80::201:e8ff:fea7:497e 300::1/64 DellEMC# Example (Tunnel) [up/up] [up/up] DellEMC# show ipv6 interface tunnel 1 Tunnel 1 is up, line protocol is up IPV6 is enabled Link Local address: fe80::201:e8ff:fea7:497e Global Unicast address(es): 400::1, subnet is 400::/64 (MANUAL) Remaining lifetime: infinite Global Anycast address(es): Joined Group address(es): ff02::1 ff02::2 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redire
PAGE 795
Example Field Description Valid MLD Packets The total number of packets received and sent from the last time the elapsed time was cleared. Reports The total number of reports (queries and unsolicited reports generated from joins or leaves) that have been received or sent. Leaves The number of Multicast leaves that have been sent. MLDv1 queries The number of MLDv1 queries that have been received. MLDv2 queries The number of MLDv2 queries that have been received.
PAGE 796
Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 796 IPv6 Basics This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 797
Example (SSeries) Field Description Gateway Identifies whether the route is directly connected and on which interface the route is configured. Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured.
PAGE 798
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.2.1.0 Introduced on the E-Series. 7.4.1.0 Introduced on the E-Series. When you configure trust IPv6 diffserv, matched bytes/packets counters are not incremented in the show qos statistics command.
PAGE 799
26 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 800
iscsi cos Set the QoS policy that is applied to the iSCSI flows. Syntax iscsi cos {enable | disable | dot1p vlan-priority-value [remark] | dscp dscp-value [remark]} To disable the QoS policy, use the no iscsi cos command. Parameters Defaults enable Enter the keyword enable to allow the application of preferential QoS treatment to iSCSI traffic so that the iSCSI packets are scheduled in the switch with a dot1p priority 4 regardless of the VLAN priority tag in the packet.
PAGE 801
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 802
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. iscsi target port Configure the iSCSI target ports and optionally, the IP addresses on which iSCSI communication is monitored.
PAGE 803
show iscsi Display the currently configured iSCSI settings. Syntax show iscsi Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 804
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. DellEMC# show isci session Session 0: -----------------------------------------------------Target: iqn.2001-05.com.equallogic:0-8a0906-0e70c2002-10a0018426a48c94iom010 Initiator: iqn.1991-05.com.
PAGE 805
Example Related Commands Version Description 8.3.12.0 Introduced on the S4810. DellEMC# show isci session detailed Session 0 : --------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-2c Up Time:00:00:01:28(DD:HH:MM:SS) Time for aging out:00:00:09:34(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.44 33345 10.10.0.
PAGE 806
27 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 807
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 808
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
PAGE 809
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1.
PAGE 810
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain. ● isis password — configure an authentication password for an interface.
PAGE 811
tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 812
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command.
PAGE 813
debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies. Syntax debug isis [vrf vrf-name] adj-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name]adj-packets [interface] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details.
PAGE 814
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF. This information contains local updates tied to the VRF that you specify. This command displays the local LSP debugging details of the current unit. interface (OPTIONAL) Identifies the interface type as one of the following: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 815
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 816
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced.
PAGE 817
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information.
PAGE 818
Usage Information Version Description 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. When you use this command to redistribute routes into a routing domain, the router becomes an autonomous system (AS) boundary router. An AS boundary router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one. How a metric value assigned to a default route advertises depends on the metric-style command configuration.
PAGE 819
distance Define the administrative distance for learned routes. Syntax distance weight [ip-address mask [prefix-list]] To return to the default values, use the no distance weight command. Parameters Defaults weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability. Routes with smaller values are given preference.) The default is 115.
PAGE 820
Parameters Defaults prefix-list-name Specify the prefix list to filter prefixes in routing updates. interface (OPTIONAL) Identifies the interface type and the interface following: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 821
Defaults ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number. The range is from 1 to 65535. rip (OPTIONAL) Enter the keyword rip for RIP routes. static (OPTIONAL) Enter the keyword static for user-configured routing process. Not configured.
PAGE 822
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 823
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. Usage Information The domain password is inserted in Level 2 link state PDUs (LSPs), complete sequence number PDUs (CSNPs), and partial sequence number PDUs (PSNPs).
PAGE 824
network. A flag in the Restart TLV contains restart request (RR), restart acknowledge (RA) and suppress adjacency advertisement (SA) bit flags. The ISIS graceful restart-enabled router can co-exist in mixed topologies where some routers are graceful restart-enabled and others are not. For neighbors that are not graceful restart-enabled, the restarting router brings up the adjacency per the usual methods.
PAGE 825
Parameters Defaults seconds Enter the graceful restart time in seconds. The range is from 5 to 300 seconds. The default is 30 seconds. 30 seconds Command Modes ROUTER ISIS Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 826
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 827
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart t3 Configure the overall wait time before graceful restart completes. Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command.
PAGE 828
Related Commands ● graceful-restart restart-wait — enable the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | point-to-point] command.
PAGE 829
Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 830
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. IS-IS normally purges LSPs with an incorrect data link checksum causing the LSP source to regenerate the message. A cycle of purging and regenerating LSPs can occur when a network link continues to deliver accurate LSPs even though there is a link causing data corruption.
PAGE 831
NOTE: IP address is not mandatory for forming IS-IS adjacency. Related Commands ● net — configure an IS-IS network entity title (NET) for the routing process. ● router isis — enable the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process. Syntax ipv6 router isis [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters Defaults tag (OPTIONAL) This parameter is a unique name for a routing process.
PAGE 832
isis circuit-type Configure the adjacency type on interfaces. Syntax isis circuit-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no isis circuit-type command. Parameters Defaults level-1 You can form a Level 1 adjacency if there is at least one common area address between this system and neighbors. You cannot form Level 2 adjacencies on this interface.
PAGE 833
To return to the default values, use the no isis csnp-interval [seconds] [level-1 | level-2] command. Parameters Defaults seconds Interval of transmission time between CSNPs on multi-access networks for the designated intermediate system. The range is from 0 to 65535. The default is 10. level-1 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 1. level-2 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 2.
PAGE 834
Defaults seconds = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 835
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 836
Version Description 8.3.11.1 Introduced on the Z9000. Usage Information Hello PDUs are “padded” only when both the global and interface padding options are ON. Turning either one OFF disables padding for the corresponding interface. Related Commands ● hello padding — turn ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information.
PAGE 837
isis metric Assign a metric to an interface. Syntax isis metric default-metric [level-1 | level-2] To return to the default values, use the no isis metric [default-metric] [level-1 | level-2] command. Parameters default-metric Metric assigned to the link and used to calculate the cost from each other router via the links in the network to other destinations. You can configure this metric for Level 1 or Level 2 routing. The range is from 0 to 16777215 irrespective of the metric style. The default is 10.
PAGE 838
isis network point-to-point Enable the software to treat a broadcast interface as a point-to-point interface. Syntax isis network point-to-point To disable the feature, use the no isis network point-to-point command. Defaults Not enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 839
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 840
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. You can configure priorities independently for Level 1 and Level 2.
PAGE 841
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The IS-IS protocol automatically determines area boundaries and are able to keep Level 1 and Level 2 routing separate. Poorly planned use of this feature may cause configuration errors, such as accidental area partitioning.
PAGE 842
lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs). Syntax lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keywords level-1 to apply the configuration to generation of Level-1 LSPs.
PAGE 843
and there are no triggers for two times the maximum interval, fast behavior is restored (the initial wait time). lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 512 to 16000 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497.
PAGE 844
Parameters Defaults seconds The LSP refresh interval, in seconds. This value must be 300 seconds less than the value specified in the max-lsp-lifetime command. The range is from 1 to 65535 seconds. The default is 900. 900 seconds Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 845
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 846
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Change the maximum LSP lifetime with this command. The maximum LSP lifetime must always be greater than the LSP refresh interval. The seconds parameter enables the router to keep LSPs for the specified length of time. If the value is higher, the overhead is reduced on slower-speed links.
PAGE 847
Version Description 6.3.1.0 Introduced. metric-style To generate and accept old-style, new-style, or both styles of type, length, and values (TLV), configure a router. Syntax metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] To return to the default values, use the no metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] command. Parameters Defaults narrow Allows you to generate and accept old-style TLVs.
PAGE 848
Related Commands ● isis metric — configure a metric for an interface. multi-topology Enables multi-topology IS-IS. It also allows enabling/disabling of old and new style TLVs for IP prefix information in the LSPs. Syntax multi-topology [transition] To return to a single topology configuration, use the no multi-topology [transition] command. Parameters Defaults transition Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific.
PAGE 849
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 850
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 851
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 852
level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only. This setting is the default. metric metric- (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0.
PAGE 853
redistribute bgp 1 level-1 metric 32 metric-type external route-map rmap-isis-to-bgp redistribute ospf Redistribute routing information from an OSPF process.
PAGE 854
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command.
PAGE 855
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Configure a network entity title (the net command) to specify the area address and the router system ID. Enable routing on one or more interfaces to establish adjacencies and establish dynamic routing. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 856
overload bit in its LSPs, other routers ignore the unreliable router in their SPF calculations until the router has recovered. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 address. show config Display the changes you made to the IS-IS configuration. Default values are not shown. Syntax show config Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific.
PAGE 857
multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database. Syntax Parameters show isis [vrf vrf-name] database [level-1 | level-2] [local] [detail | summary] [system-id] [lspid] vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IS-IS link state database corresponding to that VRF.
PAGE 858
Usage Information The following describes the show isis database command shown in the following example. Field Description IS-IS Level-1/ Level-2 Link State Database Displays the IS-IS link state database for Level 1 or Level 2. LSPID Displays the LSP identifier. The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID. If this byte is not zero, the LSP describes system links.
PAGE 859
Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 10 IPv6 (MT-IPv6) 1511::/64 Metric: 10 IPv6 (MT-IPv6) 2511::/64 Metric: 10 IPv6 (MT-IPv6) 1011::/64 Metric: 10 IPv6 1511::/64 Metric: 10 IP 10.1.1.0 255.255.255.0 Hostname: ISIS IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002D 0xB2CD 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.
PAGE 860
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 861
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. DellEMC# show isis hostname System Id Dynamic Name Static Name *F100.E120.
PAGE 862
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 863
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 864
MAC Address: 0000.0000.0000 Hold Time: 28 Link Local Address: fe80::201:e8ff:fe00:492c Topology: IPv4 IPv6 , Common (IPv4 IPv6 ) Adjacency being used for MTs: IPv4 IPv6 DellEMC# show isis protocol Display IS-IS routing information. Syntax show isis [vrf vrf-name] protocol Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS routing information corresponding to that VRF.
PAGE 865
Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode. DellEMC# show isis traffic This command allows you to display IS-IS traffic interface information. Syntax Parameters show isis [vrf vrf-name] traffic [interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS traffic interface information corresponding to that VRF.
PAGE 866
Example Item Description Level-1/Level-2 Hellos (sent/ rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs. Level-1/Level-2 LSPs flooded (sent/rcvd) Displays the number of flooded LSPs sent and received. Level-1/Level-2 LSPs CSNPs (sent/ rcvd) Displays the number of CSNP LSPs sent and received.
PAGE 867
To restore default values, use the no spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keyword level-1 to apply the configuration to Level-1 SPF calculations. level-2 (OPTIONAL) Enter the keyword level-2 to apply the configuration to Level-2 SPF calculations. interval seconds Enter the maximum number of seconds between SPF calculations. The range is from 0 to 120 seconds.
PAGE 868
28 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 869
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 870
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 871
Related Commands ● show lacp — display the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority. Syntax lacp port-priority priority-value To return to the default setting, use the no lacp port-priority priority-value command. Parameters Defaults priority-value Enter the port-priority value. The higher the value number, the lower the priority.
PAGE 872
Parameters Defaults priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 873
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP information. ● show interfaces port-channel — display information on configured Port Channel groups. show lacp Display the LACP matrix.
PAGE 874
Example (Port-ChannelNumber) Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# show lacp 1 Port-channel 1 admin up, oper up, mode lacp Actor System ID:Priority 32768, Address 0001.e800.a12b Partner System ID:Priority 32768, Address 0001.e801.
PAGE 875
29 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically.
PAGE 876
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 877
mac-address-table disable-learning Disable MAC address learning from LACP or LLDP BPDUs. Syntax Parameters Defaults mac-address-table disable-learning [lacp | lldp] lacp Enter lacp to disable MAC address learning from LACP BPDUs. lldp Enter LLDP to disable MAC address learning from LLDP BPDUs. Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 878
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 879
Usage Information Version Description 9.9(0.0) Modified the default option from none to Enabled. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series. 7.4.1.
PAGE 880
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Deprecated the no-station-move command (replaced by the mac-learninglimit mac-address-sticky command). 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 881
Parameters Defaults log Enter the keyword log to generate a syslog message on a learning-limit violation. shutdown Enter the keyword shutdown to shut down the port on a learning-limit violation. None Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 882
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 883
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.
PAGE 884
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. mac port-security Enable or disable the port security feature globally in the system. Syntax mac port-security To disable the port security, use the no mac port-security command.
PAGE 885
interface interface vlan vlan-id (OPTIONAL) Enter the keyword interface followed by the interface type, slot and port information: ● For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/port information. ● For a Port Channel interface, enter the keywords port-channel followed by a number. For the S-Series, the range is 1 to 128. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 886
interface interface-type (OPTIONAL) Instead of entering the keyword interface then the interface type, slot/port information, as above, you can enter the interface type, then just a slot number. vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display the MAC address assigned to the VLAN. The range is 1 to 4094.
PAGE 887
Example Usage Information Example (Count) Related Commands Column Heading Description State Lists if the MAC address is in use (Active) or not in use (Inactive).
PAGE 888
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.
PAGE 889
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. pre-6.2.1.1 Introduced on the E-Series. MAC Accounting information can be accessed using SNMP via the Force10 Monitor MIB.
PAGE 890
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 891
default vlan-id Specify a VLAN as the Default VLAN. Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters Defaults vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific.
PAGE 892
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 893
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 894
Example DellEMC(conf-if-vl-100)# show config ! interface Vlan 100 no ip address no shutdown DellEMC(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch.
PAGE 895
Usage Information Example Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. The following describes the show vlan command shown in the following example. Column Heading Description (Column 1 — no heading) ● ● ● ● ● ● NUM Displays existing VLAN IDs. Status Displays the word Inactive for inactive VLANs and the word Active for active VLANs. Q ● ● ● ● ● ● ● ● ● ● ● ● ● Ports Displays the type, slot, and port information.
PAGE 896
6 Active U Po3(Gi 1/4) 7 Active T Po20(Gi 1/6) P 100 Active T Po1(Gi 1/1) C 101 Inactive T Gi 1/3 I 102 Inactive T Gi 1/4 DellEMC# Example (VLAN ID) U Gi 1/3 T Po20(Gi 1/6) T Gi 1/7 T Gi 1/7 U Gi 1/5 T Gi 1/2 DellEMC# show vlan id 40 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 40 Status Description Q Ports Active M Gi 1/47 DellEMC# show vlan id 41 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untag
PAGE 897
Example (OpenFlow instance) * O O O Related Commands NUM 1 3 6 8 12 Status Inactive Inactive Inactive Inactive Inactive Description Q Ports O Gi 1/10 ● vlan-stack compatible — enable the Stackable VLAN feature on the selected VLAN. ● interface vlan — configure a VLAN. tagged Add a Layer 2 interface to a VLAN as a tagged interface. Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command.
PAGE 898
Usage Information Version Description pre-6.2.1.1 Introduced on the E-Series. When you use the no tagged command, the interface is automatically placed in the Default VLAN as an untagged interface unless the interface is a member of another VLAN. If the interface belongs to several VLANs, remove it from all VLANs to change it to an untagged interface. Tagged interfaces can belong to multiple VLANs, while untagged interfaces can only belong to one VLAN at a time.
PAGE 899
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. When this command is configured, the VLAN is operationally UP if any of the interfaces specified in the track ip command are operationally UP, and the VLAN is operationally DOWN if none of the tracking interfaces are operationally UP.
PAGE 900
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Untagged interfaces can only belong to one VLAN. In the Default VLAN, you cannot use the no untagged interface command.
PAGE 901
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection on an interface.
PAGE 902
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information When you enter no fefd for an interface and fefd-global, FEFD is enabled on the interface because the no fefd command is not retained in the configuration file.
PAGE 903
fefd interval Set an interval between control packets. Syntax fefd interval seconds To return to the default value, use the no fefd interval command. Parameters Defaults seconds Enter a number as the time between FEFD control packets. The range is from 3 to 255 seconds. The default is 15 seconds. 15 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 904
Defaults Normal Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 905
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. fefd-global interval Configure an interval between FEFD control packets.
PAGE 906
fefd-global Enable FEFD globally on the system. Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command. Parameters Defaults interval seconds Enter the keyword interval followed by the number of seconds to wait between FEFD control packets. Range is from 3 to 300 seconds. Default is 15 seconds.
PAGE 907
show fefd View FEFD status globally or on a specific interface. Syntax Parameters show fefd [interface] interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 908
Example DellEMC# show fefd FEFD is globally 'ON', interval is 10 seconds, mode is 'Aggressive'.
PAGE 909
30 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 910
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
PAGE 911
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. The advertise dot3–tlv power—via—mdi command enables the system to advertise IEEE 802.
PAGE 912
advertise management-tlv Advertise management TLVs (Type, Length, Value). Syntax advertise management-tlv {management-address | system-capabilities | system-description | system-name} To remove advertised management TLVs, use the no advertise management-tlv {management-address | system-capabilities | system-description | systemname} command. Parameters Defaults managementaddress Enter the keyword management-address to advertise the management IP address TLVs to the LLDP peer.
PAGE 913
To remove advertised management TLVs, use the no advertise management-tlv {management-address | system-capabilities | system-description | systemname} command. Parameters Defaults managementaddress Enter the keywords management-address to advertise the management IP address TLVs to the specified interface. systemcapabilities Enter the keywords system-capabilities to advertise the system capabilities TLVs to the specified interface.
PAGE 914
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.
PAGE 915
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. debug lldp interface To display timer events, neighbor additions or deletions, and other information about incoming and outgoing packets, enable LLDP debugging.
PAGE 916
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 917
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.
PAGE 918
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. management-interface Enable and configure LLDP protocol parameters on the management interface. Syntax management-interface To remove LLDP configuration on a management interface, use the no management-interface command.
PAGE 919
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 920
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch.
PAGE 921
protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 922
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. detail Defaults (OPTIONAL) Enter the keyword detail to display all the TLV information, remote management IP addresses, timers, and LLDP tx and rx counters. None Command Modes EXEC Privilege Command History Usage Information Example Example (Detail) This guide is platform-specific.
PAGE 923
Remote Chassis ID: 00:00:00:00:00:01 Remote Port Subtype: Interface name (5) Remote Port ID: TenGigabitEthernEt 1/40 Local Port ID: GigabitEthernet 1/1 Locally assigned remote Neighbor Index: 1 Remote TTL: 120 Information valid for next 44 seconds Time since last information change of this neighbor: 00:01:16 UnknownTLVList: ( 9, 4) ( 10, 4) ( 11, 4) ( 12, 4) ( 13, 4) ( 14, 4) ( 15, 4) 18, 4) ( 19, 4) ( 20, 4) ( 21, 4) ( 22, 4) ( 23, 4) ( 24, 4) ( 25, 4) 28, 4) ( 29, 4) ( 30, 4) ( 31, 4) ( 32, 4) ( 33, 4) (
PAGE 924
Remote Chassis ID: 4c:76:25:f4:ab:02 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: GigabitEthernet 1/2 Locally assigned remote Neighbor Index: 2 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),120, 4) ((00-01-66),119
PAGE 925
show lldp statistics Display the LLDP statistical information. Syntax show lldp statistics Defaults None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 926
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000 and S4810. show running-config lldp Display the current global LLDP configuration. Syntax show running-config lldp Defaults None Command Modes EXEC Privilege Command History Example 926 This guide is platform-specific.
PAGE 927
snmp-notification-interval Used to configure the value for the lldp notification interval, to throttle lldp notification messages. Syntax [no] snmp-notification-interval [seconds] To disable this feature, use the no snmp-notification-interval command. Parameters Defaults seconds Enter a value from 5 to 3600 seconds. 5 seconds Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 928
priority-tagged number Defaults Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 929
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 930
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 931
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP.
PAGE 932
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 933
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 934
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system.
PAGE 935
Related Commands Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system.
PAGE 936
advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system. Syntax advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority.
PAGE 937
31 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 938
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. vlan vlan-id Defaults Enter the keyword vlan then a VLAN ID number from 1 to 4094. Not configured. Command Modes CONFIGURATION Command History Example (Multicast) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 939
32 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the platform.
PAGE 940
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 941
Version Description 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters Defaults clear ip msdp statistic peer peer-address peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer.
PAGE 942
debug ip msdp Turn on MSDP debugging. Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters Defaults event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.).
PAGE 943
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 944
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.
PAGE 945
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters Defaults name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 946
Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 947
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. description name (OPTIONAL) Enter the keyword description then a description name (maximum 80 characters) to designate a description for the MSDP peer.
PAGE 948
ip msdp redistribute Filter local PIM SA entries in the SA cache. SAs which the ACL denies time out and are not refreshed. Until they time out, they continue to reside in the MSDP SA cache. Syntax ip msdp redistribute [list acl-name] Parameters Defaults list acl-name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured.
PAGE 949
Defaults peer-address Enter the peer address of the MSDP peer in a dotted decimal format (A.B.C.D.). access-list name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 950
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the E-Series.
PAGE 951
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 952
Parameters Defaults peer peer address Enter the keyword peer then the peer address in a dotted decimal format (A.B.C.D.). sa-cache Enter the keywords sa-cache to display the Source-Active cache. summary Enter the keyword summary to display an MSDP peer summary. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 953
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 954
33 Multicast Listener Discovery Protocol The Multicast Listener Discovery (MLD) protocol is used by IPv6 routers to discover multicast listeners on a directly attached link. Similar to the Internet Group Management Protocol (IGMP), which handles multicast group memberships in IPv4 networks, MLD is used for multicast management on IPv6 networks.
PAGE 955
debug ipv6 mld Enable debugging on IPv6 MLD packets. Syntax debug ipv6 mld [vrf vrf-name] {group-address | interface} To turn off debugging, use the no debug ipv6 mld {group-address | interface} command. Parameters Defaults vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format. The :: notation specifies successive hexadecimal fields of zero.
PAGE 956
To return to the default, use the no ipv6 mld last-member-query-interval {milliseconds} command. Parameters Defaults milliseconds Enter the last member query interval in milliseconds. The range is from 100 to 65535. 1000 milliseconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.
PAGE 957
ipv6 mld version Configure the MLD version on the system. Syntax ipv6 mld version {1 | 2} Defaults MLD version 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 958
Example Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Reporter Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires Last 00:02:05 1::2 show ipv6 mld interface View the configured MLD interfaces. Syntax show ipv6 mld [vrf vrf-name] interface [interface] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF.
PAGE 959
table entry. The switch creates only one entry per VLAN in the forwarding table for each multicast group, for which it snoops an MLD report. clear ipv6 mld snooping groups Clear entries from the group cache table. Syntax Parameters Defaults clear ipv6 mld snooping groups [interface | group-address] interface Enter the following keywords and slot/port or number information: ● For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/port information.
PAGE 960
Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping Enable MLD snooping on a VLAN. Syntax ipv6 mld snooping To disable MLD snooping, use the no ipv6 mld snooping command. Defaults Enabled on all VLAN interfaces. Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 961
Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping mrouter Configure a Layer 2 port as a multicast router port. Syntax Parameters Defaults ipv6 mld snooping mrouter interface {interface interface} interface Enter the keyword interfaceto indicate the next-hop interface to the multicast router.
PAGE 962
show ipv6 mld snooping groups Display the IPv6 MLD snooping group information. Syntax show ipv6 mld snooping groups [group address] [summary] [interface interface [detail]] Parameters group-address (Optional) Enter the multicast group addresss in the X:X:X:X::X format. The :: notation specifies successive hexadecimal fields of zero. summary (OPTIONAL) Enter the keyword summary to display a summary of groups.
PAGE 963
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Updated the output to show both MLD versions 1 and 2. 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 964
34 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 965
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 966
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● protocol spanning-tree mstp — enter MULTIPLE SPANNING TREE mode.
PAGE 967
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● max-age — change the wait time before MSTP refreshes protocol configuration information. ● hello-time — change the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs).
PAGE 968
● max-age — change the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults max-age Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 969
To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094. bridge-priority Enter the keywords bridge-priority then a value in increments of 4096 as the bridge priority. The range is from zero (0) to 61440.
PAGE 970
Defaults No default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 971
This command is supported in all STP modes such as STP, RSTP, MSTP, and PVST. The command behavior does not change when a new member port is added to the port-channel or an existing member port is deleted from the configuration. The path cost reflects the cumulative speed of the port-channel member ports.
PAGE 972
revision The revision number for the multiple spanning tree configuration. Syntax revision range To return to the default values, use the no revision command. Parameters Defaults range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 973
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 974
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Enable the multiple spanning tree protocol prior to using this command.
PAGE 975
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) loopback BPDU inconsistency causes.
PAGE 976
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------------------------------------------------------Gi 1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge Boundary ---------------------------------------------------------Gi 1/1 ErrDis 128.257 128 20000 EDS 0 P2P No No DellEMC# show spanning-tree msti 0 MSTI 0 VLANs mapped 1-4094 Root Identifier has priority 32768, Address 0001.e801.
PAGE 977
Defaults Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 978
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 979
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced By default, Dell EMC Networking OS implements an optimized flush mechanism for MSTP.
PAGE 980
35 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 981
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 982
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 983
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile.
PAGE 984
Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
PAGE 985
-4 103.103.103.3 --> Source -----------------------------------------------------------------The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic. The mtrace command traverses the reverse path to the source from the destination.
PAGE 986
-----------0 Te 1/10, 0 Te 1/10, 0 Te 1/11, 224.1.1.1 0.0.0.0 1000 1 Te 1/3, 224.1.1.2 0.0.0.0 1000 1 Te 1/3, 224.1.1.1 165.13.34.5 2000 2 Te 1/5, show ip mroute View the multicast routing table.
PAGE 987
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 988
Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 989
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources.
PAGE 990
ipv6 multicast-routing Enables IPv6 multicast forwarding. Syntax ipv6 multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable IP multicast forwarding on that VRF. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 991
9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 992
L2 Ports : L3 Ports : Te 1/10 show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 993
36 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 994
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 995
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. hardware_addres Enter a 48-bit hardware MAC address in nn:nn:nn:nn:nn:nn format. s Defaults None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 996
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 997
IPv6 Router Advertisement (RA) Guard The IPv6 RA guard provides support to perform conditional forwarding or blocking of the router advertisement messages that are received at the network device platform. This functionality analyzes and filters the RAs sent by the devices and compares the configuration information on the layer 2 device with the RA frame. Once the layer 2 device validates the content of the RA frame against the configuration, it forwards the RA to its unicast or multicast destination.
PAGE 998
device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command. Parameters Defaults host Enter the keyword host to set the device-role as host. router Enter the keyword router to set the device-role as router. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 999
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1000
ipv6 nd ra–guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1001
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters Defaults on Enter the keyword on to set the managed-config-flag value as ON.
PAGE 1002
Parameters ipv6–access-list name ipv6–prefix-list Defaults Enter the keywords ipv6–access-list then the access-list name. The accesslist name allows a maximum of 140 characters. name Enter the keywords ipv6–prefix-list then the prefix-list name. The prefix-list name allows a maximum of 140 characters. ipv6–macaccess-list name Enter the keywords ipv6–mac-access-list then the mac-access-list name. The mac-access-list name allows a maximum of 140 characters.
PAGE 1003
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1004
reachable–time Enable the verification of the configured reachability time in the received RA packets. Syntax reachable—time value To reset the advertised reachability time, use the no reachable-timevalue command. Parameters Defaults value Enter the advertised reachability time in milliseconds. The range is from 0 to 3,600,000 milliseconds. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 1005
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1006
router–preference maximum Enable the verification of the advertised default router preference (DRP) value. The preference value is lower than or equal to the specified limit. If this command is not configured, the verification process is bypassed. Syntax router-preference maximum {high | low | medium} To reset the default router preference value, use the no router-preference maximum {high | low | medium} command. Parameters Defaults high Enter the keyword high to set the DRP value as high.
PAGE 1007
Example Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1008
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Introduced on the S6000–ON, and Z9000 switches.
PAGE 1009
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1010
37 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1011
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface GigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1012
If the timer expires and an object’s state has changed, a notification is sent to the client. If no delay is configured, a notification is sent immediately after a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds. Related Commands ● track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface.
PAGE 1013
Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1014
show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object. Syntax show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500.
PAGE 1015
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP. DellEMC# show track Track 1 IP route 23.0.0.
PAGE 1016
To return to the default setting, use the no threshold metric {up number | down number} command. Parameters Defaults up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold. down number Enter a number for the DOWN threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default DOWN threshold is255.
PAGE 1017
track interface ip routing Configure object tracking on the routing status of an IPv4 Layer 3 interface. Syntax track object-id interface interface ip routing To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1018
Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1019
vrf vrf-name Defaults (Optional) You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.
PAGE 1020
A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact IPv4 address and prefix length, the status of the tracked route is considered to be DOWN.
PAGE 1021
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv4 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.
PAGE 1022
Related Commands ● show track – display information about tracked objects, including configuration, current state, and clients which track the object. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. track resolution ip route Configure the protocol-specific resolution value used to scale an IPv4 route metric.
PAGE 1023
● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. IPv6 Object Tracking Commands The following section describes the IPv6 object tracking commands.
PAGE 1024
Output Description number changes, Number of times that the state of the tracked object has changed and the time last change time since the last change in hours:minutes:seconds. Example First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP.
PAGE 1025
Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a tunnel interface, enter the keyword tunnel.
PAGE 1026
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1027
ipv6-address/ prefix-len Defaults Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1028
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1029
38 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1030
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1031
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1032
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1033
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1034
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables. Syntax clear ip ospf process-id [vrf vrf-name] [process] Parameters process-id Enter the OSPF Process ID to clear a specific process.
PAGE 1035
Version Description pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Syntax Parameters Defaults clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared.
PAGE 1036
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process. Syntax debug ip ospf [process-id] [vrf vrf-name] [bfd |event | packet | spf | database-timer rate-limit] To cancel the debug command, use the no debug ip ospf command.
PAGE 1037
Usage Information Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the debug ip ospf command shown in the Example below. Field Description 8:14 Displays the time stamp. OSPF Displays the OSPF process ID: instance ID. v: Displays the OSPF version. Dell EMC Networking OS supports version 2 only.
PAGE 1038
Example Field Description di: Displays the amount of time configured for the DEAD interval. dr: Displays the IP address of the designated router. bdr: Displays the IP address of the Border Area Router. DellEMC# debug ip ospf 1 packet OSPF process 90, packet debugging is on DellEMC# 08:14:24 : OSPF(100:00): Xmt. v:2 t:1(HELLO) l:44 rid:192.1.1.1 aid:0.0.0.1 chk:0xa098 aut:0 auk: keyid:0 to:Gi 4/3 dst:224.0.0.5 netmask:255.255.255.0 pri:1 N-, MC-, E+, T-, hi:10 di:40 dr:90.1.1.1 bdr:0.0.0.
PAGE 1039
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ● redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF.
PAGE 1040
description Add a description about the selected OSPF configuration. Syntax description description To remove the OSPF description, use the no description command. Parameters Defaults description Enter a text string description to identify the OSPF configuration (80 characters maximum). None Command Modes ROUTER OSPF Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1041
Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110. ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n format. access-list-name (OPTIONAL) Enter the name of an IP standard access list, up to 140 characters. Defaults 110 Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1042
Defaults ● external dist3 = 110 ● inter-area dist2 = 110 ● intra-area dist1 = 110 Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1043
Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1044
NOTE: BGP and ISIS routes are not available on the C-Series. BGP, ISIS, and RIP routes are not available on the S-Series. static Defaults (OPTIONAL) Enter the keyword static to specify that only manually configured routes are distributed. Not configured. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1045
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1046
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1047
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1048
Version Description 7.8.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart role Specify the role for your OSPF router during graceful restart. Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command.
PAGE 1049
ip ospf auth-change-wait-time OSPF provides a grace period while OSPF changes its interface authentication type. During the grace period, OSPF sends out packets with new and old authentication scheme until the grace period expires. Syntax ip ospf auth-change-wait-time seconds To return to the default, use the no ip ospf auth-change-wait-time command. Parameters Defaults seconds Enter the seconds. The range is from 0 to 300. zero (0) seconds.
PAGE 1050
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1051
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. If this command is not configured, cost is based on the auto-cost command.
PAGE 1052
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information By default, the dead interval is four times the default hello-interval. Related Commands ● ip ospf hello-interval — set the time interval between the hello packets.
PAGE 1053
Version Description pre- 6.1.1.1 Introduced on the E-Series. Usage Information The time interval between the hello packets must be the same for routers in a network. Related Commands ● ip ospf dead-interval — set the time interval before a router is declared dead. ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command.
PAGE 1054
To change to a different key on the interface, enable the new key while the old key is still enabled. Dell EMC Networking OS sends two packets: the first packet authenticated with the old key and the second packet authenticated with the new key. This process ensures that the neighbors learn the new key and communication is not disrupted by keeping the old key enabled. After the reply is received and the new key is authenticated, delete the old key. Dell EMC recommends keeping only one key per interface.
PAGE 1055
Parameters Defaults broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-to-point network. Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1056
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1057
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1058
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled.
PAGE 1059
maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths. 4 Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific.
PAGE 1060
Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format. (/x) area-id Enter the OSPF area ID as either a decimal value or in a valid IP address. Decimal value range is from 0 to 65535. IP address format is dotted decimal format A.B.C.D. NOTE: If the area ID is smaller than 65535, it is converted to a decimal value. For example, if you use an area ID of 0.0.0.
PAGE 1061
To return all OSPF interfaces (current and future) to active, use the no passive-interface default command. Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive. interface Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1062
● All present and future OSPF interfaces are marked as passive. ● Any adjacency is explicitly terminated from all OSPF interfaces. ● All previous passive-interface interface commands are removed from the running configuration. ● All previous no passive-interface interface commands are removed from the running configuration. no ● ● ● passive-interface interface Remove the interface from the passive list. The ABR status for the router is updated.
PAGE 1063
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1064
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1065
● 2 = for OSPF External type 2 route-map map- name tag tag-value Defaults (OPTIONAL) Enter the keywords route-map then the name of the route map. (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1066
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1067
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.
PAGE 1068
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1069
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1070
Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1071
show ip ospf database Display all LSA information. If you do not enable OSPF on the switch, no output is generated. Syntax Parameters show ip ospf process-id [vrf vrf-name] database [database-summary] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf and then the name of the VRF to view LSA information on OSPF processes corresponding to that VRF.
PAGE 1072
Example Field Description Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. DellEMC> show ip ospf 1 database OSPF Router with ID (11.1.2.1) (Process ID 1) Router (Area 0.0.0.0) Link ID ADV Router Age Seq# Checksum 11.1.2.1 11.1.2.1 673 0x80000005 0x707e 13.1.1.1 13.1.1.1 676 0x80000097 0x1035 192.68.135.2 192.68.135.2 1419 0x80000294 0x9cbd Link ID 10.2.3.2 10.2.4.2 Link ID 0.0.0.0 1.1.1.1 10.1.1.0 10.1.2.0 10.2.2.
PAGE 1073
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1074
Example DellEMC# show ip ospf 100 database asbr-summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Asbr (Area 0.0.0.0) LS age: 1437 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000000f Checksum: 0x8221 Length: 28 Network Mask: /0 TOS: 0 Metric: 2 LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.1 Advertising Router: 1.1.1.
PAGE 1075
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1076
Example Field Description External Route Tag Displays the 32-bit field attached to each external route. The OSPF protocol does not use this field, but you can use the field for external route management. DellEMC# show ip ospf 1 database external OSPF Router with ID (20.20.20.5) (Process ID 1) Type-5 AS External LS age: 612 Options: (No TOS-capability, No DC, E) LS type: Type-5 AS External Link State ID: 12.12.12.2 Advertising Router: 20.31.3.
PAGE 1077
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1078
Example DellEMC# show ip ospf 1 data network OSPF Router with ID (20.20.20.5) (Process ID 1) Network (Area 0.0.0.0) LS age: 1372 Options: (No TOS-capability, DC, E) LS type: Network Link State ID: 202.10.10.2 Advertising Router: 20.20.20.8 LS Seq Number: 0x80000006 Checksum: 0xa35 Length: 36 Network Mask: /24 Attached Router: 20.20.20.8 Attached Router: 20.20.20.9 Attached Router: 20.20.20.7 Network (Area 0.0.0.1) LS age: 252 Options: (TOS-capability, No DC, E) LS type: Network Link State ID: 192.10.10.
PAGE 1079
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1080
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1081
LS age: 1133 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.1 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000416 Checksum: 0x376 Length: 28 Opaque Type: 1 Opaque ID: 1 Unable to display opaque data LS age: 833 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.2 Advertising Router: 10.16.1.
PAGE 1082
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. ● show ip ospf database — display OSPF database information. show ip ospf database opaque-link Display the opaque-link (type 9) LSA information.
PAGE 1083
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. ● show ip ospf database — display OSPF database information.
PAGE 1084
Usage Information Example Version Description 9.4.(0.0) Added supported for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.20 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1085
LS age: 967 Options: (No TOS-capability, No DC, E) LS type: Router Link State ID: 1.1.1.10 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000012f Checksum: 0x3357 Length: 144 AS Boundary Router Area Border Router Number of Links: 10 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.129.1 (Link Data) Router Interface address: 192.68.129.1 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.130.
PAGE 1086
● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router then the IP address of an Advertising Router to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1086 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1087
Example Item Description LS Seq Number Displays the link state sequence number. This number allows you to identify old or duplicate LSAs. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the TOS options. Option 0 is the only option. Metric Displays the LSA metrics. DellEMC# show ip ospf 100 database summary OSPF Router with ID (1.1.1.
PAGE 1088
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show the OSPF processes that are tied to a specific VRF. interface (OPTIONAL) Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1089
Item Description Process ID... This line displays the OSPF Process ID, Router ID, Network type and cost metric for this interface. Transmit Delay... This line displays the interface’s settings for Transmit Delay, State, and Priority. In the State setting, BDR is Backup Designated Router. Designated Router... This line displays the ID of the Designated Router and its interface address. Backup Designated... This line displays the ID of the Backup Designated Router and its interface address.
PAGE 1090
vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show information corresponding to the OSPF neighbors that are tied to a specific VRF. Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1091
show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Syntax Parameters Defaults show ip ospf [process-id | vrf vrf-name ] routes process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show the OSPF RIB information corresponding to the OSPF processes that are tied to a specific VRF.
PAGE 1092
Dell EMC Networking OS Version 9.3(0.0). Starting with Version 9.4(0.0), the metric of E2 routes in the output is displayed as an external metric, whereas until Dell EMC Networking OS Version 9.3(0.0), the number of hops to the ASBR for E2 routes are displayed in the output. Example DellEMC# show ip ospf 100 route Prefix Cost Nexthop 1.1.1.1 1 0.0.0.0 3.3.3.3 2 13.0.0.3 13.0.0.0 1 0.0.0.0 150.150.150.0 2 13.0.0.3 172.30.1.0 2 13.0.0.
PAGE 1093
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 1094
Example Error Type Description Invld-Nbr LSA, LSR, LSU, and DDB are received from a peer which is not a neighbor peer. Nbr-State LSA, LSR, and LSU are received from a neighbor with stats less than the loading state. Auth-Error Simple authentication error. MD5-Error MD5 error Cksum-Err Checksum Error Version Version mismatch AreaMismatch Area mismatch Conf-Issue The received hello packet has a different hello or dead interval than the configuration. No-Buffer Buffer allocation failure.
PAGE 1095
Example (Statistics) DellEMC(conf-if-gi-1/6)# do show ip ospf statistics Interface GigabitEthernet 1/6 Error packets (Receive statistics) Intf-Down 0 Non-Dr 0 Self-Org 0 Wrong-Len 0 Invld-Nbr 0 Nbr-State 0 Auth-Error 0 MD5-Error 0 Cksum-Err 0 Version 0 AreaMisMatch 0 Conf-Issue 0 SeqNo-Err 0 Unknown-Pkt 0 Bad-LsReq 0 RtidZero 0 Neighbor ID 4.4.4.
PAGE 1096
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. DellEMC# show ip ospf 10 timers rate-limit List of LSAs in rate limit Queue LSA id: 1.1.1.0 Type: 3 Adv Rtid: 3.3.3.3 Expiry time: 00:00:09.111 LSA id: 3.3.3.3 Type: 1 Adv Rtid: 3.3.3.3 Expiry time: 00:00:23.96 DellEMC# show ip ospf topology Display routers in directly connected areas.
PAGE 1097
Usage Information Example To isolate problems with inter-area and external routes, use this command. In OSPF inter-area and external routes are calculated by adding LSA cost to the cost of reaching the router. If an inter-area or external route is not of correct cost, the display can determine if the path to the originating router is correct or not. DellEMC# show ip ospf 1 topology Router ID 3.3.3.3 1.1.1.1 DellEMC# Flags Cost E/B/-/ 1 E/-/-/ 1 Nexthop 20.0.0.3 10.0.0.
PAGE 1098
Usage Information Related Commands Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The area range command summarizes routes for the different areas. With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.
PAGE 1099
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage.
PAGE 1100
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 9.0.2.0 Introduced on the S6000.. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. LSAs are sent after the start-interval and then after hold-interval until the maximum interval is reached.
PAGE 1101
Version Description 8.3.8.0 Introduced on the S4810. OSPFv3 Commands Open shortest path first version 3 (OSPFv3) for IPv6 is supported on the platform. The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) remain unchanged. However, OSPFv3 runs on a per-link basis instead of on a per-IP-subnet basis. Most changes were necessary to handle the increased address size of IPv6. The Dell EMC Networking OS implementation of OSPFv3 is based on IETF RFC 2740.
PAGE 1102
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.2.0 Introduced on the E-Series. Before you enable IPsec authentication on an OSPFv3 area, you must first enable OSPFv3 globally on the router. Configure the same authentication policy (same SPI and key) on each interface in an OSPFv3 link.
PAGE 1103
key-encryptiontype key (OPTIONAL) Specifies if the authentication key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). null Defaults Causes an encryption policy configured for the area to not be inherited on the interface. Not configured.
PAGE 1104
area nssa Specify an area as a not so stubby area (NSSA). Syntax area area-id nssa [default-information-originate] [no-redistribution] [nosummary] To delete an NSSA, use the no area area-id nssa command. Parameters area-id Specify the OSPF area by entering a number from zero (0) to 65535. no-redistribution (OPTIONAL) Specify that the redistribute command does not distribute routes into the NSSA.
PAGE 1105
clear ipv6 ospf process Reset an OSPFv3 router process without removing or re-configuring the process. Syntax Parameters clear ipv6 ospf [vrf vrf-name] process vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear IPv6 routes corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1106
Command Modes EXEC Privilege Command History Usage Information Example 1106 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.1P1) Introduced VRF support. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1107
debug ipv6 ospf events Display debug information and interface types on OSPF IPv6 events. Syntax Parameters debug ipv6 ospf events [interface] [vrf vrf-name] interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1108
Met:20(E2) Opt:0x10(DN ) Prefix:9001::/64 -LSA:Router Age:1 LSId:0.0.0.0 RId:10.130.254.101 Seq:0x80000003 Flags:0x2(E) Opt:0x13(R E V6) #Links:1 -Type:TRNET Met:1 IntfId:1049476 NbrIntfId:1049476 NbrRId:10.160.3.37 from Te 0/7 DellEMC# Command Fields Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1109
Example Example (detail) Version Description 9.13(0.0) Added support for detailed debugging. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T.
PAGE 1110
Lines Beginning With or Including Description ● 4 - link state update ● 5 - link state acknowledgement Length: Displays the OSPFv3 packet length. Router ID: Displays the OSPFv3 router ID. Area ID: Displays the OSPFv3 area ID. Chksum: Displays the OSPFv3 checksum. debug ipv6 ospf spf Display debug information for SPF timers on OSPF IPv6 packets.
PAGE 1111
00:59:27 : OSPFv3INFO: Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 00:59:27 : OSPFv3INFO: Completed Enabling BFD on interface Gi 1/2 00:59:27 : OSPFv3INFO: Completed Interface mode BFD configuration on Gi 1/2!! 00:59:27 : OSPFv3INFO: Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 00:59:27 : OSPFv3INFO: Ospf3_register_bfd ospf key 27648 00:59:27 : OSPFv3INFO: OSPFV3 Enabling BFD for NBRIP fe80:0000:0000:0000:0201:e8ff:fe8b:7720 Interface Gi 1/2 IfIndex 34145282 00:59:27 : O
PAGE 1112
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. ● redistribute — redistribute routes from other routing protocols into OSPFv3.
PAGE 1113
When you enable the helper-reject role on an interface with the ipv6 ospf graceful-restart helperreject command, you reconfigure OSPFv3 graceful restart to function in a “restarting-only” role. In a “restarting-only” role, OSPFv3 does not participate in the graceful restart of a neighbor. graceful-restart mode Specify the type of events that trigger an OSPFv3 graceful restart. Syntax graceful-restart mode {planned-only | unplanned-only} To disable graceful restart mode, enter no graceful-restart mode.
PAGE 1114
ipv6 ospf area Enable IPv6 OSPF on an interface. Syntax ipv6 ospf process id areaarea id To disable OSPFv6 routing for an interface, use the no ipv6 ospf process-id area area-id command. Parameters Defaults process-id Enter the process identification number. area area-id Specify the OSPF area. The range is from 0 to 4294967295. None Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1115
For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
PAGE 1116
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.
PAGE 1117
Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Usage Information By default, the dead interval is four times longer than the default hello-interval. Related Commands ● ipv6 ospf hello-interval – specify the time interval between hello packets.
PAGE 1118
Usage Information Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.
PAGE 1119
Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on E-Series. 8.3.19.0 Introduced on the S4820T. By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA. When configured in a helper-reject role, an OSPFv3 router ignores the Grace LSAs that it receives from a restarting OSPFv3 neighbor.
PAGE 1120
ipv6 ospf priority To determine the Designated Router for the OSPFv3 network, set the priority of the interface. Syntax ipv6 ospf priority number To return to the default time interval, use the no ipv6 ospf priority command. Parameters Defaults number Enter the number as the priority. The range is from 1 to 255. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1121
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1122
Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. passive-interface Disable (suppress) sending routing updates on an interface. Syntax passive—interface interface To enable sending routing updates on an interface, use the no passive-interface interface command.
PAGE 1123
OSPFv3 for IPv6 routing information is not sent or received through the specified router interface. The specified interface address appears as a stub network in the OSPFv3 for IPv6 domain. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute into OSPFv3.
PAGE 1124
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. To redistribute the default route (x:x:x:x::x), use the default-information originate command.
PAGE 1125
If this command is used on an OSPFv3 process that is already active (has neighbors), all the neighbor adjacencies are brought down immediately and new sessions are initiated with the new router ID. show crypto ipsec policy Display the configuration of IPsec authentication and encryption policies. Syntax Parameters Defaults show crypto ipsec policy [name name] name name (OPTIONAL) Displays configuration details about a specified policy. No default behavior or values.
PAGE 1126
Transform set : esp-3des esp-md5-hmac Crypto IPSec client security policy data Policy name : OSPFv3-0-501 Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Inbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Outbound ESP Cipher Key
PAGE 1127
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults No default behavior or values. Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1128
Interface: GigabitEthernet 1/2 Link Local address: fe80::201:e8ff:fe40:4d11 IPSecv6 policy name: OSPFv3-1-600 inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 in
PAGE 1129
NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. databasesummary (OPTIONAL) Enter the keyword database-summary to view a summary of database LSA information. external (OPTIONAL): Enter the keyword external to display the external link states. grace-lsa (OPTIONAL): Enter the keyword grace-lsa to display the Type-11 Grace LSAs sent and received on an OSPFv3 router.
PAGE 1130
Usage Information Example (gracelsa) The show ipv6 ospf database command output displays detailed information on the OSPFv3 database, including link-state advertisements (LSAs). DellEMC# show ipv6 ospf 3 database grace-lsa ! Type-11 Grace LSA (Area 0) LS Age : 10 Link State ID : 6.16.192.66 Advertising Router : 100.1.1.
PAGE 1131
Example (external) DellEMC# show ipv6 ospf database external OSPFv3 Router with ID (10.160.3.37) (Process ID 6) AS External Link States (Area 0) LS Age: 1651 LS Type: OSPFv3 AS external LSA Link State ID: 0.0.0.1 Advertising Router: 10.130.254.101 LS Seq Number: 0x80000001 Checksum: 0xF038 Length: 36 Prefix: 9001::/64 Prefix Options: 0x10 ( DN ) Metric Type: 2 Metric: 20 Example (nssaexternal) DellEMC#show ipv6 ospf 10 database nssa-external OSPFv3 Router with ID (1.1.1.
PAGE 1132
Command Modes EXEC Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1133
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults None Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1134
Usage Information Example Version Description 9.14(1.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6010–ON, S6100–ON, Z9100–ON, Z9500, S6000–ON, C9010, MXL, and FN IOM. Use SNMPv3 context configuration to distinguish between various OSPFv3 VRF instances. DellEMC(conf-ipv6-router_ospf)#snmp context ospf1 DellEMC>show runnig-config ospf ! ipv6 router ospf 10 router-id 10.10.10.
PAGE 1135
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S6000-ON, S6000, S4820T, S4810, S5000. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage.
PAGE 1136
39 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1137
Related Commands Version Description 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.7.1.0 Introduced on the E-Series. ● ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times.
PAGE 1138
NOTE: Apply the redirect list to physical, VLAN, or LAG interfaces only. The Layer2 PBR option matches the layer2 traffic flow. If you un-configure this option, then the Layer2 traffic is not matched. You can apply the l2–switch option to redirect Layer2 traffic only on a VLAN interface. This VLAN interface must be configured with an IP address for ARP resolution. NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces.
PAGE 1139
permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: ● If you know the filter sequence number, use the no seq sequence-number syntax command.
PAGE 1140
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1141
● rst = reset the connection ● syn = synchronize sequence number ● urg = urgent field Defaults source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1142
[bit] [operator]{source-port source-port| source-port-range start-port end-port} {destination-port destination-port| destination-port-range startport - end-port} To delete a filter, use the no seq sequence-number command. Parameters 1142 sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the keyword IP address of the forwarding router.
PAGE 1143
destination-port- Enter the keywords destination-port-range then the range of the start port range to end port to be matched in the ACL rule in the ICAP rule. Defaults none Command Modes REDIRECT-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1144
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The show cam pbr command displays the PBR CAM content.
PAGE 1145
[up], Next-hop reachable (via Gi 1/32) seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.0/24, Track 5 [up], Next-hop reachable (via Po 5) seq 30 redirect 155.1.1.2 track 6 icmp host 8.8.8.8 any, Track 5 [up], Next-hop reachable (via Po 5) seq 35 redirect 42.1.1.2 icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20) seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30) seq 45 redirect 31.1.1.2 track 200 ip 12.0.0.0 255.0.0.197 13.0.0.0 255.0.0.
PAGE 1146
40 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
PAGE 1147
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1148
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
PAGE 1149
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled.
PAGE 1150
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1151
ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1152
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Removed the in and out parameters. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 1153
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced DellEMC(conf)# ip access-list standard map1 DellEMC(config-std-nacl)# permit 224.0.0.
PAGE 1154
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command.
PAGE 1155
ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. Syntax ip pim [vrf vrf-name] register-filter access-list To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1156
To remove an RP address, use the no ip pim [vrf vrf-name] rp-address address {group-address group-address mask} [override] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. address Enter the RP address in dotted decimal format (A.B.C.D).
PAGE 1157
To return to the default value, use the no ip pim [vrf vrf-name] rp-candidate {interface [priority]} command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Defaults interface Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1158
To disable PIM sparse mode and IGMP, use the no ip pim sparse-mode command. Defaults Disabled. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1159
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1160
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.7(0.0) Added support for VRF. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1161
vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. infinity Defaults (OPTIONAL) Enter the keyword infinity to never switch to the source-tree. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1162
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced on the E-Series. By default, when you enable PIM-SM snooping, a switch floods all multicast traffic to the PIM designated router (DR), including unnecessary multicast packets. To minimize the traffic sent over the network to the designated router, you can disable designated-router flooding.
PAGE 1163
Example Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. DellEMC# show ip pim bsr-router PIMv2 Bootstrap information This system is the Bootstrap Router (v2) BSR address: 7.7.7.7 (?) BSR Priority: 0, Hash mask length: 30 Next bootstrap message in 00:00:08 This system is a candidate BSR Candidate BSR address: 7.7.7.7, priority: 0, hash mask length: 30 DellEMC# show ip pim interface View information on the interfaces with IP PIM enabled.
PAGE 1164
Usage Information The following describes the show ip pim interface command shown in the following example. Field Description Address Lists the IP addresses of the interfaces participating in PIM. Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), of the interfaces participating in PIM.
PAGE 1165
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim neighbor command shown in the following example.
PAGE 1166
Command History Example Example (Mapping) Example (Address) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1167
● EXEC Privilege Command History Usage Information Example (#2) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1168
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series. The following describes the show ip pim snooping neighbor commands shown in the following example.
PAGE 1169
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1170
Incoming interface: Vlan 2, RPF neighbor 0.0.0.0 Outgoing interface list: GigabitEthernet 2/11 RPF 165.87.32.2 00:00:01/00:02:59 GigabitEthernet 2/13 Upstream Port -/DellEMC# show ip pim snooping tib vlan 2 225.1.2.1 165.87.1.7 PIM Multicast Snooping Table Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune SGR-P - (S,G,R) Prune Timers: Uptime/Expires * : Inherited port (165.87.1.7, 225.1.2.1), uptime 00:00:08, expires 00:02:52, flags: j Incoming interface: Vlan 2, RPF neighbor 0.0.0.
PAGE 1171
Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Group Address / MaskLen show ip pim summary View information about PIM-SM operation. Syntax Parameters show ip pim [vrf vrf-name] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1172
PIM-SNOOPING Interface 1 0 3 summary: active PIM interface passive PIM interfaces active PIM neighbors TIB summary: 1/1 (*,G) entries in PIM-TIB/MFC 1/1 (S,G) entries in PIM-TIB/MFC 0/0 (S,G,Rpt) entries in PIM-TIB/MFC 0 0 0 0 PIM nexthops RPs sources Register states Message summary: 2582/2583 Joins sent/received 5/0 Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 State-Refresh messages sent/received 0/0 MSDP updates sent/received 0/0 Null Register m
PAGE 1173
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1174
Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (20.10.4.9, 225.1.1.1), uptime 00:06:21, expires 00:02:06, flags: CT Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (*, 225.1.1.2), uptime 00:40:15, expires 00:00:00, RP 20.40.4.4, flags: SCJ Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (20.
PAGE 1175
IPv6 PIM-Sparse Mode Commands The following describes the IPv6 PIM-sparse mode (PIM-SM) commands. clear ipv6 pim tib Clear the IPv6 PIM multicast-routing database (tree information base—TIB). Syntax Parameters clear ipv6 pim [vrf vrf-name] tib [group-address] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1176
● hello: to view the IPv6 PIM neighbor keepalive timer ● joinprune: to view the expiry timer (join/prune timer) ● register: to view the register suppression timer Defaults Disabled. Command Modes EXEC Privilege Command History Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. ipv6 pim bsr-border Define the border of IPv6 PIM domain by filtering inbound and outbound PIM-BSR messages per interface.
PAGE 1177
takes the precedence. If the priority values are equal, the router with the higher IP address becomes the BSR. The default is 0. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, S3048-ON, S3100 Series, S4048-ON, S4048T-ON, S6000-ON, S6010-ON, S6100-ON, Z9100-ON.
PAGE 1178
Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. ipv6 pim rp-address Configure a static PIM rendezvous point (RP) address for a group. First-hop routers use this address to send register packets on behalf of the source multicast host.
PAGE 1179
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. interface Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1180
ipv6 pim sparse-mode sg-expiry-timer Enable expiry timers globally for all sources. Syntax ipv6 pim [vrf vrf-name] sparse-mode sg-expiry-timer seconds To disable configured timers and return to default mode, use the no ipv6 pim sparse-mode sgexpiry-timer command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable expiry timer for all sources on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1181
Usage Information PIM leaf routers join the shortest path tree immediately after the first packet arrives from a new source. show ipv6 pim bsr-router View information on the bootstrap router. Syntax Parameters show ipv6 pim [vrf vrf-name] bsr-router vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1182
Mode Count Intvl Gi 1/16 v2/S 1 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router Prio 101 Gi 1/17 v2/S 1 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router 100 Gi 1/19 v2/S 0 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router 1 show ipv6 pim neighbor Displays IPv6 PIM neighbor information.
PAGE 1183
NOTE: The :: notation specifies successive hexadecimal fields of zero. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Example (Mapping) Version Description 9.11.3.
PAGE 1184
show ipv6 pim summary View information about PIM-SM operation. Syntax show ipv6 pim [vrf vrf-name] summary Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1185
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format to view RP mappings for a specific group. NOTE: The :: notation specifies successive hexadecimal fields of zero. source-address (OPTIONAL) Enter the source address in the x:x:x:x::x format.
PAGE 1186
41 Power over Ethernet (PoE) DellEMC Networking OS supports Power over Ethernet (PoE) and Power over Ethernet Plus (PoE+) on S3100 series systems. Use the commands in this chapter to configure the Power over Ethernet (PoE) on the S3100 platforms.
PAGE 1187
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. The advertise dot3–tlv power—via—mdi command enables the system to advertise IEEE 802.
PAGE 1188
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. Example show lldp neighbors — displays the LLDP neighbors.
PAGE 1189
Unit Total System Redundancy Inline Inline Inline Inline Inline Power Power Power Power Power Power Power Power Available Consumed Consumed Threshold Available Allocated Consumed Remaining (Watts) (Watts) (Watts) (%) (Watts) (Watts) (Watts) (Watts) ---------------------------------------------------------------------------------------1 1100 150 0 10 95 0 0 95 DellEMC# power inline Use this command to enable inline power and configure maximum power allocation with priority for the powered device connected
PAGE 1190
Total Inline Power Consumed: Remaining inline power Available: Power Management Mode: Static Interface Inline Power Inline Power LLDP Max / Alloc Consumed Support (Watts) (Watts) -----------------------------------Gi 1/1 30.00/0.00 0.00 DellEMC# 0W 95W Class ------- Device PoE Port Type Priority ------ -------- NO_DEVICE - high power inline legacy Use this command to allocate inline power to the legacy devices on the specified stack unit.
PAGE 1191
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant DellEMC Networking OS Command Line Reference Guide. The following is a list of the DellEMC Networking OS version history for this command. Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.8(2.0) Introduced on the S3100 series.
PAGE 1192
power inline restore You can use this command to enable the temporarily suspended PoE power supply to all the ports in a stack unit. Syntax power inline restore stack-unit unit number Parameters stack-unit unit number Defaults Enter the keyword stack-unit and the stack-unit number. Range is from 1 to 12. None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant DellEMC Networking OS Command Line Reference Guide.
PAGE 1193
% Error: Power to stack-unit 1 is in suspended state. DellEMC# show power detail You can use this command to display the inline power consumption details for a specified stack unit. Syntax Parameters show power detail {stack-unit unit number} stack-unit unit number Defaults Enter the stack-unit keyword and the unit number. Range is 1 to 12. None Command Modes EXEC Command History This guide is platform-specific.
PAGE 1194
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.8(2.0) Introduced on the S3100 series. The following table describes the output fields of the show power inline command: Field Description Interface Displays the line card or the interface slot and port number. Inline Power Allocated Displays the amount of power allocated to the port.
PAGE 1195
42 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1196
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1197
monitor multicast-queue Configure monitor QoS multicast queue ID. Syntax monitor multicast-queue queue-id To remove the configuration, use the no monitor multicast-queue command. Parameters Defaults queue-id Enter the QoS multicast queue ID. The range is from 0 to 9. queue-id: 0 Enable status: Disabled Command Modes CONFIGURATION Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific.
PAGE 1198
Defaults set ip dscp Configures the Differentiated Services Code Point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default value, use the no form of this command. dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic.
PAGE 1199
rate-limit Configure the rate-limit to limit the mirrored packets. Syntax rate-limit limit To remove the limit, use the no rate-limit limit command. Parameters Defaults limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. 60 Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1200
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1201
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1202
Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1203
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. ● For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. ● For a port channel interface, enter the keywords port-channel then a number. range Enter the keyword range to specify the list of interfaces. any Enter the keyword any to specify all interfaces.
PAGE 1204
Example 1204 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1205
43 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1206
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1207
To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN. primary Enter the keyword primary to configure the VLAN as a primary VLAN. none Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific.
PAGE 1208
Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input. none Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1209
Defaults Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1210
44 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1211
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Syntax disable To enable PVST+, use the no disable command. Defaults Disabled.
PAGE 1212
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
PAGE 1213
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1214
show spanning-tree pvst View the Per-VLAN spanning tree configuration. Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters Defaults vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1215
Usage Information Example (Brief) Version Description 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples. Field Description Interface Name PVST interface. Instance PVST instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1216
Port 146 (GigabitEthernet 1/16) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.146 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1217
spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard. Syntax Parameters spanning-tree pvst {edge-port [bpduguard [shutdown-on-violation]] | errdisable | vlan vlan-range {cost number | priority value} | loopguard | rootguard} edge-port Enter the keywords edge-port to configure the interface as a PVST+ edge port.
PAGE 1218
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series, C-Series, and S-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the hardware shutdown-on-violation option. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1219
Related Commands ● show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1220
To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1221
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1222
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1223
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. ● vlan bridge-priority — sets the bridge-priority value.
PAGE 1224
Related Commands 1224 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. ● vlan bridge-priority — sets the bridge-priority value. ● vlan forward-delay — changes the time interval before Dell EMC Networking OS transitions to the forwarding state. ● vlan hello-time — changes the time interval between BPDUs.
PAGE 1225
45 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1226
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis.
PAGE 1227
When you set the priority for a port channel, the physical interfaces assigned to the port channel are configured with the same value. You cannot assign the dot1p-priority command to individual interfaces in a port channel. rate police Police the incoming traffic rate on the selected interface. Syntax Parameters Defaults rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] [vlan vlan-id] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1228
S-Series On one interface, you can configure the rate police command for a VLAN or you can configure the rate police command for an interface. rate-shape Shape the traffic output on the selected interface. Syntax rate shape [kbps] rate [burst-KB] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
PAGE 1229
Related Commands ● rate-shape — shapes traffic output as part of the designated policy. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. Syntax Parameters Defaults service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} queue Enter a value from 0 to 7.
PAGE 1230
Defaults All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command. The default mapping is as follows: dot1p Queue ID 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 Command Modes ● INTERFACE ● CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 1231
strict-priority unicast Configure a unicast queue as a strict-priority (SP) queue. Syntax Parameters Defaults strict-priority unicast number unicast number Enter the keyword unicast then the queue number. The range is from 1 to 3. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1232
Parameters Defaults percentage Enter the percentage assignment of bandwidth to the class/queue. The range is from 1 to 100% (granularity 1%). none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1233
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1234
● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1235
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1236
Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1237
set-ip-dscp value (OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63. Defaults none Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.
PAGE 1238
match ip precedence Use IP precedence values as a match criteria. Syntax [seq sequence number] match {ip | ipv6 | ip-any} precedence ip-precedencelist [set-ip-dscp value] To remove IP precedence as a match criteria, use the no match {ip | ipv6 | ip-any} precedence ip-precedence-list [[multicast] set-ip-dscp value] command. Parameters seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100.
PAGE 1239
Usage Information Version Description 6.1.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip precedence command and the match ip dscp command are mutually exclusive. Up to eight precedence values can be matched in one match statement. For example, to indicate the IP precedence values 0 1 2 3, enter either the match ip precedence 0-3 or match ip precedence 0,1,2,3 command.
PAGE 1240
match ip vrf Uses a VRF as the match criterion for an L3 class map. Syntax match ip vrf vrf-id To remove VRF as the match criterion, use the no match ip vrf vrf-id command. Parameters Defaults vlan vlan-id Enter the keyword vrf and then the ID of the VRF. The range is from 1 to 511. none Command Modes CONF-CLASS-MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1241
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.
PAGE 1242
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.1.0 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria.
PAGE 1243
Version Description 8.2.1.0 Introduced. Usage Information To access this command, enter the class-map command. You can match against only one VLAN ID. Related Commands ● class-map — identifies the class map. policy-aggregate Allow an aggregate method of configuring per-port QoS via policy maps. An aggregate QoS policy is part of the policy map (output) applied on an interface.
PAGE 1244
Related Commands ● policy-map-input — creates an input policy map. ● policy-map-output — creates an output policy map. policy-map-input Create an input policy map. Syntax policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] To remove an input policy map, use the no policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] command. Parameters Defaults policy-map-name Enter the name of the policy map in character format (32 characters maximum).
PAGE 1245
Usage Information The input policy map is used to classify incoming traffic to different flows using class-map, QoS policy, or incoming packets DSCP. This command enables Policy-Map-Input Configuration mode (conf-policy-mapin). When you configure an input policy map for CoPP, you must enter the keyword cpu-qos . Related Commands ● service-queue — assigns a class map and QoS policy to different queues. ● service-policy input — applies an input policy map to the selected interface.
PAGE 1246
qos-policy-input Create a QoS input policy on the router. Syntax qos-policy-input qos-policy-name cpu-qos | layer2 To remove an existing input QoS policy from the router, use the no qos-policy-input qospolicy-name cpu-qos | layer2 command. Parameters Defaults qos-policy-name Enter the name for the policy map in character format (32 characters maximum). cpu-qos (OPTIONAL) Enter the keyword cpu-qos keyword to assign this ACL to control plane traffic only.
PAGE 1247
qos-policy-output Create a QoS output policy. Syntax qos-policy-output qos-policy-name To remove an existing output QoS policy, use the no qos-policy-output qos-policy-name command. Parameters Defaults qos-policy-name Enter your output QoS policy name in character format (32 characters maximum). none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1248
Defaults committed-rate Enter the bandwidth in Mbps. The range is from 0 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB. The range is from 16 to 200000. The default is 100. peak peak-rate (OPTIONAL) Enter the keyword peak then a number to specify the peak rate in Mbps. The range is from 0 to 40000. The default is the same as designated for committed-rate. Burst size is 100KB. peak-rate is by default the same as committed-rate.
PAGE 1249
Defaults burst-kbps (OPTIONAL) Enter the burst size in KB. The range is from 0 to 40000. The default is 100. burst-packets Enter the peak rate or committed rate burst size in packets per seconds. Burst size is 10KB. Granularity for rate is Mbps unless you use the kbps option. Command Modes QOS-POLICY-OUT Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1250
service-policy input Apply an input policy map to the selected interface. Syntax service-policy input policy-map-name [layer2] To remove the input policy map from the interface, use the no service-policy input policymap-name [layer2] command. Parameters policy-map-name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist.
PAGE 1251
service-policy output Apply an output policy map to the selected interface. Syntax service-policy output policy-map-name To remove the output policy map from the interface, use the no service-policy output policy-map-name command. Parameters Defaults policy-map-name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. none Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1252
Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7. class-map class- (OPTIONAL) Enter the keyword class-map then the class map name assigned to the queue in character format (32 character maximum). map-name NOTE: This option is available under policy-map-input only. qos-policy qos- policy-name Defaults (OPTIONAL) Enter the keywords qos-policy then the QoS policy name assigned to the queue in text format (32 characters maximum).
PAGE 1253
mac-dot1p value Defaults Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7. none Command Modes CONFIGURATION (conf-qos-policy-in) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1254
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1255
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information trust dot1p, do1p-priority, service-class dynamic dot1; all these features work over the mapping in this command output. Related Commands ● service-class dot1p-mapping — Identifies the class map. show qos policy-map View the QoS policy map information.
PAGE 1256
Example (IPv4) Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series only: Added trust IPv6 diffserv . 6.2.1.1 Introduced on the E-Series.
PAGE 1257
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1258
qos-policyoutput qos- Enter the keyword qos-policy-output then the QoS policy name. policy-name Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1259
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1260
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1261
Version Description 9.12(0.0) Modified to display the global WRED state. 9.11(0.0) Updated the show qos statistics egress—queue output to reflect per queue per port drop rates. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 1262
NOTE: When you configure trust , matched packet counters are not incremented in this field. ● Matched Bytes — The number of bytes that matched the class-map criteria. NOTE: When you configure trust , matched byte counters are not incremented in this field. ● Dropped Pkts — The total of the number of packets dropped for green, yellow and out-of-profile. show qos wred-profile View the WRED profile details.
PAGE 1263
test cam-usage Check the Input Policy Map configuration for the CAM usage. Syntax Parameters test cam-usage service-policy input policy-map stack-unit {[number port-set portpipe number] | [all]} policy-map Enter the policy map name. stackunit number (OPTIONAL) Enter the keyword stack-unit then the stack-unit slot number. port-set portpipe Enter the keywords port-set then the stack-unit port pipe number. The range is number from 0 or 1.
PAGE 1264
Field Description NOTE: The CAM entries reserved for the default rules are not included in the Available CAM column; free entries, from the default rules space, cannot be used as a policy map for the classification rules. Estimated CAM per Port Indicates the number of free CAM entries required (for the classification rules) to apply the input policy map on a single interface.
PAGE 1265
Command Modes CONFIGURATION (config-wred) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1266
Command Modes CONFIGURATION (conf-policy-map-in) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1267
Table 6. Default Mapping (continued) DSCP/CP hex DSCP Range (XXX) Definition Traditional IP Precedence S6000 Internal Queue ID S-Series Internal Queue ID DSCP/CP Decimal 000XXX Best Effort 0 0 0–15 BE (Best Effort) wred Designate the WRED profile to yellow or green traffic. Syntax wred {yellow | green} profile-name To remove the WRED drop precedence, use the no wred {yellow | green} [profile-name] command. Parameters yellow | green Enter the keyword yellow for yellow traffic.
PAGE 1268
Related Commands ● wred-profile — creates a WRED profile and name that profile. ● trust — defines the dynamic classification to trust DSCP. wred ecn To indicate network congestion, rather than dropping packets, use explicit congestion notification (ECN). Syntax wred ecn To stop marking packets, use the no wred ecn command. Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History Usage Information This guide is platform-specific.
PAGE 1269
wred-profile Create a WRED profile and name the profile. Syntax wred-profile wred-profile-name To remove an existing WRED profile, use the no wred-profile command. Parameters wred-profilename Enter your WRED profile name in character format (32 character maximum). Or use one of the pre-defined WRED profile names. You can configure up to 26 WRED profiles plus the five pre-defined profiles, for a total of 31 WRED profiles. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_g.
PAGE 1270
DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red. Traffic marked as yellow delivers traffic to the egress queue which will either transmit the packet if it has available bandwidth or drop the packet due to no ability to send. Traffic marked as red (high drop precedence) is dropped. dscp Sets the number of specific DSCP values for a color map profile to yellow or red.
PAGE 1271
Example Related Commands DellEMC(conf-dscp-color-map)# dscp yellow 9,10,11,13,15,16 ● qos dscp-color-map — configures the DSCP color map. ● qos dscp-color-policy— configures a DSCP color policy. qos dscp-color-map Configure the DSCP color map. Syntax qos dscp-color-map map-name To remove a color map, use the no qos dscp-color-map map-name command. Parameters Defaults map-name Enter the name of the DSCP color map. The map name can have a maximum of 32 characters.
PAGE 1272
To remove a color policy map profile, use the no dscp-color-policy color-map-profile-name command. Parameters Defaults color-mapprofile-name Enter the color map profile name. The name can have a maximum of 32 characters. None Command Modes CONFIG-INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1273
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display summary information about a color policy on one or more interfaces.
PAGE 1274
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps.
PAGE 1275
46 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1276
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1277
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1278
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic. Syntax default-information originate [always] [metric metric-value] [route-map map-name] To return to the default values, use the no default-information originate command.
PAGE 1279
Usage Information The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command. Syntax default-metric number To return the default metric to the original values, use the no default-metric command. Parameters Defaults number Specify a number. The range is from 1 to 16.
PAGE 1280
description Enter a description of the RIP routing protocol. Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the RIP protocol (80 characters maximum). none Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1281
Defaults mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x). prefix-name (OPTIONAL) Enter a configured prefix list name. weight = 120 Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1282
Defaults Not configured. Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1283
Defaults isis (OPTIONAL) Enter the keyword isis to filter only IS-IS routes. ospf (OPTIONAL) Enter the keyword ospf to filter all OSPF routes. static (OPTIONAL) Enter the keyword static to filter manually configured routes. Not configured. Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1284
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1285
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information If you want the interface to receive both versions of RIP, use the ip rip receive version 1 2 command.
PAGE 1286
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable the interface to send both version of RIP packets, use the ip rip send version 1 2 command. Related Commands ● ip rip receive version — sets the RIP version for the interface to receive traffic. ● version — sets the RIP version for the switch software.
PAGE 1287
maximum-paths Set RIP to forward packets over multiple paths. Syntax maximum-paths number To return to the default values, use the no maximum-paths commands. Parameters Defaults number Enter the number of paths. The range is from 1 to 16. The default is 4 paths. 4 Command Modes ROUTER RIP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1288
Defaults Not configured. Command Modes ROUTER RIP Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1289
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1290
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1291
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command is intended for low-speed interfaces.
PAGE 1292
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1293
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command. Related Commands ● default-information originate — generates a default route for RIP traffic. redistribute isis Redistribute routing information from an IS-IS instance.
PAGE 1294
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 6.2.1.1 Introduced on the E-Series. redistribute ospf Redistribute routing information from an OSPF process. Syntax redistribute ospf process-id [match external {1 | 2} | match internal | metric metric-value] [route-map map-name] To disable redistribution, use the no redistribute ospf process-id [match external {1 | 2} | match internal | metric metric-value] [route-map map-name] command.
PAGE 1295
Version Description pre- 6.2.1.1 Introduced on the E-Series. router rip To configure and enable RIP, enter ROUTER RIP mode. Syntax router rip To disable RIP, use the no router rip command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1296
show config Display the changes you made to the RIP configuration. The default values are not shown. Syntax show config Command Modes ROUTER RIP Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1297
Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1298
[50/2] via 1.1.120.2, 00:00:55, Port-channel 20 [50/2] via 1.1.130.2, 00:00:12, Port-channel 30 [50/2] via 1.1.10.2, 00:00:18, Vlan 10 208.250.42.0/24 auto-summary DellEMC# show running-config rip Display the current RIP configuration. Syntax show running-config rip Defaults none Command Modes EXEC Privilege Command History Example 1298 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1299
timers basic Manipulate the RIP timers for routing updates, invalid, holddown times, and flush time. Syntax timers basic update invalid holddown flush To return to the default settings, use the no timers basic command. Parameters Defaults update Enter the number of seconds to specify the rate at which RIP routing updates are sent. The range is from zero (0) to 4294967295. The default is 30 seconds.
PAGE 1300
Usage Information If you change the timers on one router, also synchronize the timers on all routers in the RIP domain. version Specify either RIP version 1 or RIP version 2. Syntax version {1 | 2} To return to the default version setting, use the no version command. Parameters Defaults 1 Enter the keyword 1 to specify RIP version 1. 2 Enter the keyword 2 to specify RIP version 2. The Dell EMC Networking OS sends RIPv1 and receives RIPv1 and RIPv2.
PAGE 1301
47 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1302
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1303
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1304
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1305
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
PAGE 1306
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1307
show rmon Display the RMON running status including the memory usage. Syntax show rmon Defaults none Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1308
brief Defaults (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) 1308 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1309
13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table. Syntax Parameters Defaults show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format.
PAGE 1310
options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none. event community: event last time sent: none event owner: event status: OK RMON event entry 112 description: event type: LOG. event community: event last time sent: none event owner: event status: OK RMON event entry 113 description: event type: SNMP TRAP. event community: private event last time sent: none event owner: event status: OK RMON event entry 114 description: event type: LOG and SNMP TRAP.
PAGE 1311
Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1312
show rmon history Display the contents of the RMON Ethernet history table. Syntax show rmon history [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an easy-to-read format none Command Modes EXEC Command History Example (Index) Example (Brief) 1312 This guide is platform-specific.
PAGE 1313
9001 134529054 9002 134529054 9003 134791198 9004 134791198 DellEMC# GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet 3/2 3/2 3/1 3/1 show rmon log Display the contents of the RMON log table. Syntax Parameters Defaults show rmon log [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON log table in an easyto-read format.
PAGE 1314
Example (Brief) DellEMC# show rmon log br eventIndex description -----------------------------2 2 4 4 DellEMC# show rmon statistics Display the contents of RMON Ethernet statistics table. Syntax show rmon statistics [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet statistics table in an easy-to-read format.
PAGE 1315
CRC error: 0 under-size packets: 0 over-size packets: 0 fragment errors: 0 jabber errors: 0 collision: 0 64bytes packets: 0 65-127 bytes packets: 0 128-255 bytes packets: 0 256-511 bytes packets: 0 512-1023 bytes packets: 0 1024-1518 bytes packets: 0 owner: 1 status: OK HC packets received overflow: 0 HC packets received: 0 HC bytes received overflow: 0 HC bytes received: 0 HC 64bytes packets overflow: 0 HC 64bytes packets: 0 HC 65-127 bytes packets overflow: 0 HC 65-127 bytes packets:
PAGE 1316
48 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1317
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1318
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# debug spanning-tree rstp bpdu gigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree.
PAGE 1319
disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1320
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1321
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1322
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● forward-delay — changes the wait time before RSTP transitions to the Forwarding state. ● hello-time — changes the time interval between BPDUs.
PAGE 1323
Example Related Commands DellEMC(conf)# protocol spanning-tree rstp DellEMC(config-rstp)# no disable ● disable — disables RSTP globally on the system. show config View the current configuration for the mode. Only non-default values are displayed. Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1324
guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example (Brief) 1324 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1325
Gi 4/1 128.419 128 20000 FWD 20000 16384 0001.e801.6aa8 128.419 Gi 4/8 128.426 128 20000 FWD 20000 8192 0001.e805.e306 128.130 Gi 4/9 128.427 128 20000 BLK 20000 8192 0001.e805.e306 128.131 Interface Name Role ----------Gi 4/2 Desg Gi 4/1 Desg Gi 4/8 Root Gi 4/9 Altr DellEMC# Example (EDS, LBK) PortID Prio Cost Sts Cost Link-type Edge ---- ------- --- ------- --------- ---128.418 128 20000 FWD 20000 P2P Yes 128.419 128 20000 FWD 20000 P2P Yes 128.426 128 20000 FWD 20000 P2P No 128.
PAGE 1326
Parameters cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1327
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the optional bridge port data unit (BPDU) guard. 6.2.1.1 Introduced on the E-Series. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1328
Usage Information 1328 Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.
PAGE 1329
49 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
PAGE 1330
50 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant. Topics: • • • • • • • • • • • • AAA Accounting Commands Authorization and Privilege Commands Obscure Password Commands Authentication and Password Commands RADIUS Commands TACACS+ Commands Port Authentication (802.
PAGE 1331
Defaults commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: ● For name, enter a user-defined name of a list of accounting methods. ● For default, the default accounting methods used.
PAGE 1332
Example (TACACS+) DellEMC(conf)# aaa accounting exec default start-stop tacacs+ DellEMC(conf)# aaa accounting command 15 default start-stop tacacs+ DellEMC(conf)# aaa accounting command role secaadmin default start-stop tacacs+ Example (RADIUS) Related Commands DellEMC(conf)# aaa accounting dot1x default start-stop radius DellEMC(conf)# aaa accounting dot1x default stop-only radius ● ● ● ● enable password — changes the password for the enable command.
PAGE 1333
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. ● aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL. Syntax aaa accounting suppress null-username To permit accounting records to users with user name value of NULL, use the no aaa accounting suppress null-username command.
PAGE 1334
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1335
Usage Information Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.
PAGE 1336
Defaults commands { level | role role-name } Enter the keyword commands followed by either a privilege level for accounting of commands executed at that privilege level, or enter the keyword role then the role name for authorization of commands executed by a user with that user role. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands. none Command Modes LINE Command History Related Commands This guide is platform-specific.
PAGE 1337
Defaults default Define the default list of authorization methods. local Use the authorization parameters on the system to perform authorization. tacacs+ Use the TACACS+ protocol to perform authorization. none Enter the keyword none to apply no authorization. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1338
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1339
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS.
PAGE 1340
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1341
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys.
PAGE 1342
If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command. Related Commands ● show running-config— Display the current configuration and display changes from the default values. ● service password-encryption— Encrypts all passwords configured in the system. Authentication and Password Commands To manage access to the system, use the following the commands.
PAGE 1343
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell EMC Networking OS uses the methods defined for Enable access instead.
PAGE 1344
... method4 Defaults (OPTIONAL) Enter up to four additional methods. In the event of a “no response” from the first method, the system applies the next configured method (up to four configured methods). Not configured (that is, no authentication is performed). Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1345
Related Commands ● ● ● ● login authentication — enables AAA login authentication on the terminal lines. password — creates a password. radius-server host — specifies a RADIUS server host. tacacs-server host — specifies a TACACS+ server host. access-class Restrict incoming connections to a particular IP address in a defined IP access control list (ACL). Syntax access-class access-list-name To delete a setting, use the no access-class command.
PAGE 1346
Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced this command. When an operating system enables to change the user authenticators, the users might access resources and perform tasks that they do not have authorization.
PAGE 1347
Usage Information Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1348
password Defaults Enter a text string, up to 96 characters long, as the clear text password. No password is configured. level = 15. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1349
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Only Dell EMC Networking Technical Support staff use this command. enable secret Change the password for the enable command. Syntax enable secret [level level] [encryption-type] password To delete a password, use the no enable secret [encryption-type] password [level level] command.
PAGE 1350
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: ● Start with a letter, not a number. ● Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression.
PAGE 1351
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. If you configure the aaa authentication login default command, the login authentication default command automatically is applied to all terminal lines.
PAGE 1352
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1353
upper number (OPTIONAL) Enter the keyword upper then the upper number. The range is from 0 to 31. lower number (OPTIONAL) Enter the keyword lower then the lower number. The range is from 0 to 31. numeric number (OPTIONAL) Enter the keyword numeric then the numeric number. The range is from 0 to 31. special-char (OPTIONAL) Enter the keywords special-char then the number of special characters permitted. The range is from 0 to 31. number The following special characters are supported: !"#%&'();<=>?[\]
PAGE 1354
secure-cli enable Enable the secured CLI mode. Syntax secure-cli enable Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced this command. The secured CLI mode prevents the users from enhancing the permissions or promoting the privilege levels.
PAGE 1355
Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security. When the passwords are encrypted, you cannot return them to plain text unless you re-configure them. To remove an encrypted password, use the no password password command. To keep unauthorized people from viewing passwords in the switch configuration file, use the service password-encryption command.
PAGE 1356
Related Commands ● privilege level (CONFIGURATION mode) — assign access control to different command modes. show users Allows you to view information on all users logged in to the switch. Syntax show users [all] Parameters all (OPTIONAL) Enter the keyword all to view all terminal lines in the switch. Command Modes EXEC Privilege Command History Usage Information Example 1356 Security This guide is platform-specific.
PAGE 1357
* 0 console 0 idle 2 vty 0 admin idle 10.16.127.35 3 vty 1 ad idle 10.16.127.145 4 vty 2 ad1 idle 10.16.127.141 5 vty 3 ad1 idle 10.16.127.145 6 vty 4 admin idle 10.16.127.141 7 vty 5 ad idle 10.16.127.141 DellEMC# Related Commands unassigned 1 unassigned 1 unassigned 15 sysadmin 1 sysadmin 1 unassigned 1 unassigned 15 ● username — enables a user. timeout login response Specify how long the software waits for the login input (for example, the user name and password) before timing out.
PAGE 1358
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The software measures the period of inactivity defined in this command as the period between consecutive keystrokes. For example, if your password is “password” you can enter “p” and wait 29 seconds to enter the next letter. username Establish an authentication system based on user names.
PAGE 1359
Usage Information Version Description 9.14(1.0) Introduced dynamic-salt option on the S4810 and S4820T. 9.13.0.0 Enhanced to display a warning message when a weak password is used. Introduced the dynamic-salt option on the MXL, S5000, S4048-ON, S6000, S6000-ON, S3048-ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1360
RADIUS Commands The following RADIUS commands are supported by Dell EMC Networking OS. aaa radius auth-method Configure the authentication method to use with RADIUS for user access. Syntax aaa radius auth-method {pap | mschapv2} To undo the RADIUS authentication method configuration, use the no aaa radius auth-method command. Parameters Defaults pap Enter the keyword pap to use the Password Authentication Protocol (PAP) for RADIUS authentication.
PAGE 1361
● 7 – implies that the key is encrypted and hidden. key Enter a string that is the key to be exchanged between the switch and the dynamic authorization client. The key can be up to 42 characters long. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● It is possible to configure more than one dynamic authorization clients Duplicate (ipv4-addr or ipv6addr or host-name) configurations are not allowed. Command History This guide is platform-specific.
PAGE 1362
To remove the port bounce configuration, enter the no coa-bounce-port command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Configure no coa-bounce-port to drop radius CoA port-bounce requests from the DAC. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command.
PAGE 1363
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. debug radius View RADIUS transactions to assist with troubleshooting. Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1364
Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Time for DAS to wait before the back end response is received. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1365
Usage Information Version Description 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. If this configuration is not enabled, then dynamic authorization messages are not handled by the NAS. ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections.
PAGE 1366
Version Description pre-6.2.1.0 Introduced on the E-Series. port Configures NAS port number to accept CoA or DM requests. Syntax port port-number To remove the NAS port configuration, enter the no port command. Defaults Parameters 3799 port-number Enter the NAS port number to accept CoA and DM requests. The range is from 1 to 65535. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Optionally specify dynamic authorization port number. Default port is 3799.
PAGE 1367
radius-server attribute include-in-access-req Initiates the RADIUS server with the Framed-IP-address or Framed-IPv6-address to be assigned to the host connected to the switch. Syntax Parameters radius-server attribute attribute-number include-in-access-req attribute attribute-number Defaults Enter the attribute keyword and the number. ● 8- Enter the number to initiate the RADIUS server with the Framed-IP-address to be assigned to the host.
PAGE 1368
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1369
radius-server host 2.2.2.2 key 7 9a2f3ec0c65c6f41 DellEMC(conf-radius-group)# Related Commands ● login authentication — sets the database to be checked when a user logs in. ● radius-server key — sets an authentication key for RADIUS communications. ● radius-server retransmit — sets the number of times the RADIUS server attempts to send information. ● radius-server timeout — sets the time interval before the RADIUS server times out. radius-server host Configure a RADIUS server host.
PAGE 1370
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.
PAGE 1371
radius-server vrf Create an association between a RADIUS server group and a VRF and source interface. ud Syntax radius-server vrf vrf-name [source-interface interface] To delete the association between a RADIUS server group and a VRF and source interface, use the no radius-server vrf vrf-name [source-interface interface] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a RADIUS server group with that VRF.
PAGE 1372
Example DellEMC(conf)#radius-server group group1 DellEMC(conf-radius-group)#radius-server vrf vrf1 source-interface gigabitethernet 1/42 DellEMC(conf)#radius-server group group2 DellEMC(conf-radius-group)#radius-server vrf default radius-server key Configure a key for all RADIUS communications between the switch and the RADIUS host server. Syntax radius-server key [encryption-type] key To delete a password, use the no radius-server key command.
PAGE 1373
If you configure the key parameter in the radius-server host command, the key configured with the radius-server key command is the default key for all RADIUS communications. Related Commands ● radius-server host — configures a RADIUS host. radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable.
PAGE 1374
To return to the default value, use the no radius-server timeout command. Parameters Defaults seconds Enter the number of seconds between an unsuccessful attempt and the Dell EMC Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds. 5 seconds Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1375
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. replay-protection-window Configure replay protection window period to drop the duplicate packets. Syntax replay-protection-window minutes To undo the configuration, enter the no replay-protection-window command. Defaults Parameters 5 Minutes.
PAGE 1376
TACACS+ Commands Dell EMC Networking OS supports TACACS+ as an alternate method for login authentication. tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command . Parameters Defaults group-name Enter the name of the TACACS server group. Not configured.
PAGE 1377
Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1378
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1379
Usage Information Example Related Commands You can associate a TACACS server group with a VRF. DellEMC(conf)# tacacs-server group group1 DellEMC(conf-tacacs-group)# tacacs-server host 1.1.1.1 key secret DellEMC(conf-tacacs-group)# tacacs-server host 2.2.2.2 key secret DellEMC(conf-tacacs-group)# tacacs-server vrf vrf1 source-interface gigabitethernet 1/40 DellEMC(conf-tacacs-group)# show config ! tacacs-server group group1 tacacs-server vrf vrf1 source-interface GigabitEthernet 1/40 tacacs-server host 1.
PAGE 1380
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 1381
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1382
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1383
● If an 802.1X port is authenticated and put in the RADIUS server assigned VLAN, any change to the port access VLAN configuration does not take effect. ● The 802.1X with VLAN assignment feature is not supported on trunk ports, dynamic ports, or with dynamic-access port assignment through a VLAN membership. dot1x authentication (Configuration) Enable dot1x globally; dot1x must be enabled both globally and at the interface level.
PAGE 1384
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1385
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed attempts, the interface is moved to the authentication failed VLAN.
PAGE 1386
dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific.
PAGE 1387
dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell EMC Networking OS attempts to authenticate the host based on its MAC address. Syntax [no] dot1x mac-auth-bypass Defaults Disabled Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1388
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1389
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator performs authentication only when port-control is set to auto. dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command.
PAGE 1390
Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated. The range is from 1 to 31536000 (1 year). The default is3600 (1 hour). 3600 seconds (1 hour) Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1391
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1392
Version Description 7.4.1.0 Introduced on the E-Series. dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Syntax dot1x supplicant-timeout seconds To return to the default, use theno dot1x supplicant-timeout command. Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30.
PAGE 1393
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1394
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. DellEMC#show dot1x interface tengigabitethernet 1/49 802.
PAGE 1395
Auth PAE State: Backend State: DellEMC# Initialize Initialize SSH and SCP Commands Dell EMC Networking OS supports secure shell (SSH) protocol version 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted and use authentication. crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1396
Usage Information The host keys are required for key-exchange by the SSH server. If the keys are not found when you enable the server (ip ssh server enable), the keys are automatically generated. This command requires user interaction and generates a prompt prior to overwriting any existing host keys. NOTE: Only a user with superuser permissions should generate host-keys. Example Related Commands DellEMC(conf)# crypto key generate rsa Enter key size <1024-2048>. Default<1024> : Host key already exists.
PAGE 1397
Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1398
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command.
PAGE 1399
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh challenge–response–authentication Enable challenge response authentication for SSHv2.
PAGE 1400
● 3des-cbc Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON, S6000, S6000–ON, S5000, S4810, S4820T, S3048– ON, S4048–ON, MXL, C9010, S3100 series, and Z9100-ON.
PAGE 1401
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server. Syntax ip ssh hostbased-authentication enable To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbasedauthentication enable command. Parameters Defaults enable Enter the keyword enable to enable hostbased-authentication for SSHv2 server. Disabled.
PAGE 1402
ip ssh key-size Configure the size of the server-generated RSA SSHv1 key. Syntax ip ssh key-size 512-869 Parameters Defaults 512-869 Enter the key-size number for the server-generated RSA SSHv1 key. The range is from 512 to 869. The default is 768. Key size 768 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1403
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1404
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file.
PAGE 1405
● hmac-sha1–96 When FIPS mode is disabled: ● hmac-sha2-256 ● hmac-sha1 ● hmac-sha1–96 ● hmac-md5 ● hmac-md5-96 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1406
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL ip ssh rhostsfile Specify the rhost file used for host-based authorization. Syntax ip ssh rhostsfile {WORD} Parameters Defaults WORD Enter the rhost file name for the host-based authentication. none Command Modes CONFIGURATION Command History Example Usage Information This guide is platform-specific.
PAGE 1407
NOTE: For rhostfile and pub-key-file, the administrator must FTP the file to the switch. ip ssh rsa-authentication (Config) Enable RSA authentication for the SSHv2 server. Syntax ip ssh rsa-authentication enable To disable RSA authentication, use the no ip ssh rsa-authentication enable command. Parameters Defaults enable Enter the keyword enable to enable RSA authentication for the SSHv2 server. Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1408
To disable SSH server functions, use the no ip ssh server {ciphers cipher-list} {enable | port port-number} [kex key-exchange-algorithm] [mac hmac-algorithm] command. Parameters enable Enter the key word enable to start the SSH server. ciphers cipher- Enter the keyword ciphers and then a space-delimited list of ciphers that the SSH server supports. The following ciphers are available.
PAGE 1409
● diffie-hellman-group14-sha1 When FIPS is enabled, the default key-exchange-algorithm is diffie-hellmangroup14-sha1. When FIPS is not enabled, the default key-exchange-algorithms are the following: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1, ● diffie-hellman-group14-sha1 port port-number (OPTIONAL) Enter the keyword port then the port number of the listening port of the SSH server. The range is from 1 to 65535. The default is 22.
PAGE 1410
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22. NOTE: Starting with Dell EMC Networking OS Release 9.2(0.0), SSH server is enabled by default.
PAGE 1411
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1412
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000.
PAGE 1413
Usage Information Example Version Description 9.4(0.0) Introduced on the S-Series and Z9000. If you configure a VRF for an SSH session, then you need not explicitly mention the same VRF for the SSH client sessions intended for that VRF. The vrf attribute in the ip ssh vrf command is applicable for both the SSH client as well as the COPY (SCP) commands. DellEMC(conf)#ip ssh vrf vrf1 DellEMC(conf)#do ssh 10.10.10.
PAGE 1414
Example DellEMC# show crypto key mypubkey rsa ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQC9IYgcUcc8wQm+5KUQgW/ zAs8V5STalGq4/+S+6H9axpQnA+A0xweeo5iR5hvPP6Vc+HS+uWoQH+ VOJ8H5Jxsm347XnYv/gpSqhgjZ/C5UwFiucVkVfYu8RDcJVIuQhLv PEebIF5Q+sD8K89MXU90MAS/UdoiJZSOIlbaCuSTW1Q== DellEMC# Related Commands ● crypto key generate — generates the SSH keys. show ip ssh Display information about established SSH sessions. Syntax NOTE: Some of the parameters in this command require licensing to access.
PAGE 1415
cbc,aes128-ctr,aes128-cbc,3des-cbc. SSH server macs : hmac-sha2-256,hmac-sha1,hmac-sha1-96,hmacmd5,hmac-md5-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffiehellman-group1-sha1,diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Challenge Response Auth : enabled. Vty Encryption HMAC Remote IP 2 aes128-cbc hmac-md5 10.16.127.141 4 aes128-cbc hmac-md5 10.16.127.141 * 5 aes128-cbc hmac-md5 10.16.127.
PAGE 1416
2200:2200:2200:2200:2200::2202 ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAu5NoTbmnLxBknaeXZmUJMupNwNUoGlo1/ yLPI5eehQTyaldRPHtGyPlcmMbCH+QJkqtyiwDPmH4njyDMYDCXY85vc55ibWsN9qalagklnh2cj2q4nYj5x8+8OOhYeFPaHiygd8 FXict61jWs84Co1UTsAgRzDJ9aUSS75TVac= root@dt-maa-li nux-1.force10networks.com 10.16.151.
PAGE 1417
freedom@poclab4 DellEMC# Related Commands ● ip ssh rsa-authentication (Config) — configures the RSA authorized keys. ssh Open an SSH connection specifying the hostname, username, encryption cipher, HMAC algorithm, port number, and version of the SSH client. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1418
● hmac-sha1: Force ssh to use hmac-sha1 HMAC algorithm. ● hmac-sha1-96 : Force ssh to use hmac-sha1-96 HMAC algorithm. ● hmac-sha2-256 : Force ssh to use hmac-sha2-256 HMAC algorithm. Defaults -p port-number (OPTIONAL) Enter the keyword -p then the port number. The range is from 1 to 65535. The default is 22. -v 2 (OPTIONAL) Enter the keyword -v then the SSH version 2. The default is the version from the protocol negotiation. As shown in the Parameters section.
PAGE 1419
Usage Information Example Dell EMC Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. DellEMC#ssh 10.16.151.48 -l anvltest Trying 10.16.151.48... 01:18:16: %STKUNIT0-M:CP %SEC-5-SSH_USAGE: Initiated SSH Client v2 (FIPS Disabled) to anvltest@10.16.151.48 by default from console anvltest@10.16.151.
PAGE 1420
ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [trust-downstream | vrf] Parameters Defaults trustdownstream Configure the system to trust Option 82 when it is received from the previous-hop router. vrf Enter the keyword vrf to include VRF related information in the Option 82. This configuration enables the relay agent to include VRF related information when it forwards the broadcasts from client to DHCP server. Disabled.
PAGE 1421
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 1422
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1423
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1424
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable IP source guard. Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1425
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1426
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ● clear ip dhcp snooping — clear the contents of the DHCP binding table. Role-Based Access Control Commands With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role.
PAGE 1427
Usage Information Version Description 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. By default, access to commands are determined by the user’s role (if defined) or by the user’s privilege level. If the aaa authorization role-only command is enabled, then only the user’s role is used. Before you enable role-based only AAA authorization: 1. Locally define a system administrator user role.
PAGE 1428
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Users entering EXEC Privilege mode or any other configured privilege level can access configuration commands. To protect against unauthorized access, use the enable password command to configure a password for the enable command at a specific privilege level.
PAGE 1429
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. ● userrole — creates user roles. show role Display information on permissions assigned to a command, including user role and/or permission level.
PAGE 1430
Examples DellEMC# show role mode configure username Role access: sysadmin DellEMC# show role mode configure management route Role access: netadmin, sysadmin DellEMC# show role mode configure management crypto-policy Role access: secadmin, sysadmin Related Commands ● userrole — create user roles. show userroles Display information on all defined user roles.
PAGE 1431
Route-map Protocol MAC Related Commands ● userrole — create user roles. userrole Create user roles for the role-based security model. Syntax userrole name inherit existing-role-name To delete a role name, use the no userrole name command. Note that the reserved role names may not be deleted. Parameters name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1432
● Make sure you select the correct role you want to inherit. NOTE: If you inherit a user role, you cannot modify or delete the inheritance. If you want to change or remove the inheritance, delete the user role and create it again. If the user role is in use, you cannot delete the user role. role mode { { { addrole | deleterole } role-name } | reset } command – Modifies (adds or deletes) command permissions for newly created user roles and system defined roles.
PAGE 1433
Table 8.
PAGE 1434
System Security Commands The following section lists the system security commands. generate hash Generate a hash checksum for the given file or the startup configuration using the MD5, SHA1, or SHA256 algorithm. Syntax generate hash {md5 | sha1 | sha256} {flash://filename | startup-config} Parameters Defaults md5 | sha1 | sha256 Enter the keyword md5, sha1, or sha256 to generate .
PAGE 1435
Command History Usage Information Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM. If you configure the secure-cli command on the system, the Dell EMC Networking OS resets any previously-configured root access password to the default root password without displaying any warning message.
PAGE 1436
verified boot hash Verify and store the hash value of the startup configuration. Syntax verified boot hash {system-image {A: | B:} | startup-config} hash value Parameters Defaults system-image {A: Enter the keyword system-image and A: or B:, depending on where the image | B:} is stored and then the hash value that is present on the iSupport page for your image. startup-config Enter the keyword startup-config and then the hash value for the startup configuration.
PAGE 1437
51 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1438
Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID. The range is from 1 to 4094. count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Debug disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1439
Example Related Command Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1440
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command ● show protocol-tunnel — displays tunneling information for all VLANs.
PAGE 1441
protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters Defaults rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History Example Related Commands This guide is platform-specific.
PAGE 1442
show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax show protocol-tunnel [vlan vlan-id] Parameters Defaults vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094. none Command Modes EXEC Command History Example Example (Specific VLAN) Related Commands 1442 This guide is platform-specific.
PAGE 1443
52 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1444
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6address} agent-addr {ipv4-address | ipv6-address} [number [max-datagramsize number]] | [max-datagram-size number] [vrf management] command.
PAGE 1445
Usage Information Version Description 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
PAGE 1446
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
PAGE 1447
sflow extended-switch enable Enable packing information on a switch only. Syntax sflow extended-switch enable To disable packing information, use the no sflow extended-switch [enable] command. Parameters Defaults enable Enter the keyword enable to enable global extended information. Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1448
Parameters Defaults extended Enter the keyword extended to copy 256 bytes from the sample packets to sFlow datagram. 128 bytes Command Modes CONFIGURATION INTERFACE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1449
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1450
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This command sets the counter polling interval for an interface. Related Commands ● sflow polling-interval (Global) — globally sets the polling interval. sflow sample-rate (Global) Change the global default sampling rate.
PAGE 1451
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This command changes the global default sampling rate. You can configure an interface to use a different sampling rate than the global sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power of 2 value.
PAGE 1452
Usage Information This command changes the sampling rate for an interface. By default, the sampling rate of an interface is set to the same value as the current global default sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power-of-2 value. Select one of these two number and re-enter the command. Related Commands ● sflow sample-rate (Global) — changes the sampling rate globally.
PAGE 1453
Usage Information Example The dropEvent counter (sFlow samples dropped due to sub-sampling) shown in the following example always displays a value of zero. DellEMC#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header size: 128 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.1, Agent IP addr: 1.1.1.
PAGE 1454
53 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1455
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1456
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 1457
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
PAGE 1458
RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1459
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1460
snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1461
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
PAGE 1462
The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB. If a community string is configured without a security-name (for example, snmp-server community public ro), the community is mapped to a default security-name/group: ● v1v2creadu / v1v2creadg — maps to a community with ro (read-only) permissions. ● v1v2cwriteu/ v1v2cwriteg — maps to a community with rw (read-write) permissions. The community-name parameter indexes this command.
PAGE 1463
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps.
PAGE 1464
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the following two SNMP notification options: syslog-reachable and syslog-unreachable. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.
PAGE 1465
NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device. If no VRF is specified, then the default VRF is used. udp-port port- number engineID Defaults Enter the keywords udp-port followed by the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. As above. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1466
snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
PAGE 1467
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.2 Added support for the access parameter. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1468
NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps. informs (OPTIONAL) Enter the keyword informs to send inform notifications to the specified host. The default is traps.
PAGE 1469
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148 and S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1470
To 1. 2. 3. 4. 5. Related Commands send an inform, use the following steps: Configure a remote engine ID. Configure a remote user. Configure a group for this user with access rights. Enable traps. Configure a host to receive informs. ● snmp-server enable traps — enables SNMP traps. ● snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server.
PAGE 1471
Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32. Packet sizes are 8000 bytes, 16000 bytes, 32000 bytes, and 64000 bytes. 8 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1472
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1473
remote ip- address Enter the keywords udp-port then the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. vrf vrf-name Enter the keywords vrf and then the name of the VRF this is used to connect to the SNMP server. NOTE: Use this attribute to specify a VRF name that is used to connect to the remote host. If no VRF is specified, then the default VRF is used.
PAGE 1474
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.(0.0) Added aes 128 encryption algorithm parameter. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1475
snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826. RFCs for SNMPv3 define two authentication hash algorithms, namely, HMAC-MD5-96 and HMAC-SHA1-96. These are the full forms or editions of the truncated versions, namely, HMAC-MD5 and HMAC-SHA1 authentication algorithms.
PAGE 1476
not previously set up. Otherwise, you must remove the previously configured users before you change the FIPS mode. Example Related Commands DellEMC# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv aes128 d0452401a8c3ce42804fe80e3ba8763d ● show snmp user — Displays the information configured on each SNMP user name. snmp-server view Configure an SNMPv3 view.
PAGE 1477
Usage Information Example Related Commands The oid-tree variable is a full sub-tree starting from 1.3.6 and cannot specify the name of a sub-tree or a MIB. The following Example configures a view named rview that allows access to all objects under 1.3.6.1. DellEMC# conf DellEMC#(conf) snmp-server view rview 1.3.6.1 included ● show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF.
PAGE 1478
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1479
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1480
default logging buffered Return to the default setting for messages logged to the internal buffer. Syntax default logging buffered Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1481
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging console — set the logging console parameters.
PAGE 1482
Related Commands ● logging monitor — set the logging monitor parameters. ● terminal monitor — send system messages to the terminal/monitor. default logging trap Return to the default settings for logging messages to the Syslog servers. Syntax default logging trap Defaults level = 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1483
Defaults hostname Enter the name of a host already configured and recognized by the switch. udp Enter the keyword udp to enable transmission of log message over UDP followed by port number. The default port is 514 tcp Enter the keyword tcp to enable transmission of log message over TCP followed by port number. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to enable the logging process in VRF mode.
PAGE 1484
logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. Syntax logging buffered [level] [size] To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffered command.
PAGE 1485
logging console Specify which messages are logged to the console. Syntax logging console [level] To return to the default values, use the default logging console command. To disable logging to the console, use the no logging console command. Parameters Defaults level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1486
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1487
● ● ● ● ● ● ● ● ● ● ● ● ● local7 (local use) lpr (line printer system) mail (mail system) news (USENET news) sys9 (system use) sys10 (system use) sys11 (system use) sys12 (system use) sys13 (system use) sys14 (system use) syslog (Syslog process) user (user process) uucp (Unix to Unix copy process) The default is local7. Defaults local7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1488
To return to the default values, use the no logging history command. Parameters Defaults level Indicate a value from 0 to 7 or enter one of the following equivalent words: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 4 or warnings. warnings or 4 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1489
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1490
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1491
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you use the no logging on command, messages are logged only to the console. Related Commands ● ● ● ● logging logging logging logging — enable logging to the Syslog server. buffered — set the logging buffered parameters. console — set the logging console parameters. monitor — set the logging parameters for the terminal connections.
PAGE 1492
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1493
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1494
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5.
PAGE 1495
Example DellEMC(conf)#logging version ? <0-1> Select syslog version (default = 0) DellEMC(conf)#logging version 1 show logging Display the logging settings and system messages logged to the internal buffer of the switch. Syntax Parameters show logging [number | history [reverse][number] | reverse [number] | summary] number (OPTIONAL) Enter the number of messages displayed in the output. The range is from 1 to 65535.
PAGE 1496
Console logging: level debugging Monitor logging: level debugging Buffer logging: level debugging, 5604 Messages Logged, Size (524288 bytes) Trap logging: level informational Oct 8 09:25:37: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 223.80.255.254 closed. Hold time expired Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.13.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.1.1.13 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 1.1.14.
PAGE 1497
Example Related Commands Version Description 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. DellEMC(conf)# show logging auditlog ● clear logging auditlog — clear the audit log. show logging driverlog stack-unit Display the driver log for the specified hardware component.
PAGE 1498
f10EepromBlkRead@psu0eeprom: Main block failed checksum calulated checksum 0x1d actual chksum 0x0 3:Task(tUsrRoot): [ 61]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main block failed errcode 6 4:Task(tUsrRoot): [ 89]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed checksum calulated checksum 0xc9a6 actual chksum 0x0 5:Task(tUsrRoot): [ 57]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed errcode 6 6:Task(tUsrRoot): [ 51]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom, faile
PAGE 1499
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging monitor — set the logging parameters on the monitor/terminal.
PAGE 1500
54 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1501
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
PAGE 1502
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
PAGE 1503
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 TRAP OID Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
PAGE 1504
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1505
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
PAGE 1506
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
PAGE 1507
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
PAGE 1508
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
PAGE 1509
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1510
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
PAGE 1511
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
PAGE 1512
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE lldp-ext-med.
PAGE 1513
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generates an event that is configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
PAGE 1514
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation conflict resolved during audit 113 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
PAGE 1515
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE Object Name MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
PAGE 1516
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1. Above threshold" 133 TR_VLT_DOMAIN _CFG_ERROR 134 DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote there is a error/conflict in the VLT domain config parameters (either locally or in remote node which prevent the peer up.
PAGE 1517
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls. An agent should not generate more than one entConfigChange 'notification-event' in a given time interval (five seconds is the suggested default). A 'notification-event' is the transmission of a single trap or inform PDU to a list of notification destinations.
PAGE 1518
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.23 dellNetSysAlarmCa DELLrdVersionMismatch NETWORKINGCHASSIS-MIB.
PAGE 1519
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
PAGE 1520
55 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1521
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1522
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
PAGE 1523
Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1524
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree — enter SPANNING TREE mode on the switch.
PAGE 1525
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● max-age — changes the wait time before STP refreshes protocol configuration information. ● hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1526
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults seconds Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1527
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1528
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1529
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1530
Example Field Description “Designated port...” Displays the designated port ID. DellEMC# show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
PAGE 1531
Example (Guard) Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1532
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1533
56 Stacking All commands in this chapter are specific to the Dell EMC Networking OS. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, see the Stacking S-Series Switches section in the Dell EMC Networking OS Configuration Guide.
PAGE 1534
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the members option. Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the running-config. Related Commands show redundancy — displays the current redundancy status.
PAGE 1535
redundancy protocol Enable hitless failover for a protocol. Syntax Protocols Defaults redundancy protocol lacp Enter the LACP protocol xstp Enter one of the following protocols: STP, RSTP, MSTP, PVST. Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1536
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the hard reset option. Resetting the management unit is not allowed, and an error message displays if you try to do so. Resetting is a soft reboot, including flushing the forwarding tables. Starting with Dell EMC Networking OS version 7.8.1.0, you can run this command directly on the stack standby unit (standby master) to reset the standby.
PAGE 1537
● ● ● ● ● Example except — show only text that doesn not match a pattern. find — search for the first occurrence of a pattern. grep — show only text that matches a pattern. no-more — do not paginate the output. save — save the output to a file.
PAGE 1538
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 1538 Stacking This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1539
Example (Status) Example (Topology) Related Commands DellEMC#show system stack-ports status Topology: Ring Interface Link Speed Admin Link (Gb/s) Status Status -------------------------------------------1/29 10 up up 1/30 10 up up 2/29 10 up up 2/30 10 up up 3/29 10 up up 3/30 10 up up 4/53 10 up up 4/54 10 up up 5/53 10 up up 5/54 10 up up 6/53 10 up up 6/54 10 up up 7/29 10 up up 7/30 10 up up 8/29 10 up up 8/30 10 up up 9/29 10 up up 9/30 10 up up 10/53 10 up up 10/54 10 up up 11/29 10 up up 11/30 10
PAGE 1540
stack-unit priority Configure the ability of a switch to become the management unit of a stack. Syntax stack-unit stack-number priority priority-value Parameters Defaults stack-number Enter the stack member unit identifier. priority-value This preference parameter allows you to specify the management priority of one backup switch over another, with 1 as the lowest priority and 14 being the highest.
PAGE 1541
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. ● reload – reboot the Dell EMC Networking OS. ● show system – display the status of all stack members or a specific member.
PAGE 1542
● show system — displays the status of all stack members or a specific member. ● show version — displays the current Dell EMC Networking OS version information on the system.
PAGE 1543
57 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1544
Parameters Defaults interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 1545
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1546
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1547
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1548
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.
PAGE 1549
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter. It is possible, however, that some multicast control traffic may get dropped when storm control thresholds are exceeded.
PAGE 1550
To disable storm control for unknown-unicast traffic, use the no storm-control unknownunicast [packets_per_second in] command. Parameters Defaults packets_per_sec ond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1551
● 100% allows all traffic into the interface. The decimal range is from 0.1 to 0.9. Defaults wred-profile name E-Series Only: (Optionally) Enter the keywords wred-profile followed by the profile name to designate a wred-profile. packets_per_sec ond in C-Series and S-Series Only: Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554431. none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 1552
58 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1553
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1554
Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1555
support-assist activity Trigger an activity event immediately. Syntax Parameters support-assist activity {full-transfer | core-transfer} start now full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information. core-transfer Enter the keyword core-transfer to specify transfer of core files. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1556
Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. Introduced the core-transfer and event-transfer parameters. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. By default, each activity follows a set of default actions using a default schedule.
PAGE 1557
Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes. last-name Enter the last name for the contact person. To include a space, enter a space within double quotes. Command Modes SUPPORTASSIST Command History Usage Information This guide is platform-specific.
PAGE 1558
server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode. Syntax server {default | server-name} To delete a server, use the no server server-name command. Parameters Defaults default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred. To include a space, enter a space within double quotes. Default server has URL stor.g3.ph.dell.
PAGE 1559
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
PAGE 1560
Related Commands ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest show — view the list of action-manifest for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. action-manifest remove Remove the action-manifest file from Dell EMC Networking OS. Syntax action-manifest remove } Parameters local-file-name Enter the name of the local action-manifest file.
PAGE 1561
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest install — configure the action-manifest to use for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. enable Enable a specific SupportAssist activity.
PAGE 1562
To remove the complete company contact information, use the no address command. Parameters city company- city province | region | state name (OPTIONAL) Enter the keyword city then the city or town for the company site. To include a space, enter a space within double quotes. (OPTIONAL) Enter the keyword province, region or state then the name of province, region or state for the company site. To include a space, enter a space within double quotes.
PAGE 1563
Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. territory Configure the territory and set the coverage for the company site.
PAGE 1564
Parameters primary email- address alternate emailaddress Enter the keyword primary then the primary email address for the person. Enter the keyword alternate then the alternate email address for the person. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM.
PAGE 1565
Related Commands ● preferred-method — configure the preferred method for contacting the person. preferred-method Configure the preferred method for contacting the person. Syntax Parameters Defaults preferred-method {email | no-contact | phone] email Enter the keyword email to specify email as preferred method. no-contact Enter the keywords no-contact to specify that there is no preferred method. phone Enter the keyword phone to specify phone as preferred method.
PAGE 1566
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. SupportAssist Server Commands Dell EMC Networking OS supports the following SupportAssist Server mode commands. proxy-ip-address Configure a proxy for reaching the SupportAssist remote server.
PAGE 1567
Usage Information The passwords are stored encrypted in the running configuration. enable Enable communication with the SupportAssist server. Syntax enable To disable communication to a specific SupportAssist server, use the no enable command. Defaults Enabled Command Modes SUPPORTASSIST SERVER Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1568
Usage Information The URL should be formatted to follow the ISO format. show eula-consent Display the EULA for the feature. Syntax show eula-consent {support-assist | other feature} Parameters support-assist | other feature Enter the keywords support-assist or the text corresponding to other feature. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1569
allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dells affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
PAGE 1570
preferred-method email time-zone zone +05:30 start-time 12:23 end-time 15:23 ! server Dell enable url http://1.1.1.1:1332 DellEMC# show support-assist status Display information on SupportAssist feature status including any activities, status of communication, last time communication sent, and so on. Syntax show support-assist status Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1571
59 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1572
Defaults end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year. The range is from 1993 to 2035. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to1440. The default is 60 minutes.
PAGE 1573
● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month. ● last: Enter this keyword to start daylight saving time in the last week of the month. Defaults start-day Enter the name of the day that you want daylight saving time to begin. Use English three letter abbreviations; for example, Sun, Sat, Mon, and so on. The range is from Sun to Sat.
PAGE 1574
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key. ● clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. ● show clock — displays the current clock settings.
PAGE 1575
Usage Information Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8. debug ntp Display Network Time Protocol (NTP) transactions and protocol messages for troubleshooting.
PAGE 1576
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp authentication-key Specify a key for authenticating the NTP server.
PAGE 1577
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. After configuring the ntp authentication-key command, configure the ntp trusted-key command to complete NTP authentication. Dell EMC Networking OS versions 8.2.1.
PAGE 1578
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option. Syntax ntp control-key-passwd [encryption-type] password To delete the control key, use the no ntp control-key-passwd [encryption-type] password command.
PAGE 1579
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1580
ntp offset-threshold Configure the threshold time interval before which the system generates an NTP audit log message if the time difference from the NTP server is greater than a threshold value (offset-threshold). Syntax ntp offset-threshold threshold-value To disable the threshold value, use the no ntp offset-threshold command. Parameters offset-threshold threshold-value Defaults (Optional) Enter the keyword offset-threshold and then the threshold value. The range is from 0 to 999. Zero (0).
PAGE 1581
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) The trusted-key range value is increased from 1 to 65534. Also, introduced the minpoll and maxpoll polling interval options. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1582
ntp source Specify an interface’s IP address to be included in the NTP packets. Syntax ntp source interface To delete the configuration, use the no ntp source command. Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1583
ntp trusted-key Set a key to authenticate the system to which NTP synchronizes. Syntax ntp trusted-key number To delete the key, use the no ntp trusted-key number command. Parameters Defaults number Enter a number as the trusted key ID. The range is from 1 to 65534. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1584
Command History Example Example (Detail) Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1585
Usage Information Example (without ntp master configuration) Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 1586
Example (with ntp master configuration) Dell EMC#show ntp associations remote vrf-Id ref clock st when poll reach delay offset di ================================================================================== *LOCAL(0) 0 .LOCL. 7 6 16 377 0.000 0.000 0.002 10.16.127.86 0 10.16.127.26 5 9 16 1 65.292 13829.9 0.002 10.16.127.144 0 10.16.127.26 5 6 16 1 0.829 13795.2 0.002 10.16.127.44 0 10.16.127.26 5 16 1 0.799 13791.5 0.
PAGE 1587
show ntp status Display the current NTP status. Syntax show ntp status Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1588
peer mode is client DellEMC# Related Commands 1588 ● show ntp associations — displays information on the NTP master and peer configurations.
PAGE 1589
60 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1590
Usage Information The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
PAGE 1591
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
PAGE 1592
Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1593
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000.
PAGE 1594
tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit value To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters Defaults value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64.
PAGE 1595
Defaults Tunnel keepalive is disabled. Command Modes INTERFACE TUNNEL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1596
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. To enable a tunnel interface, use this command.
PAGE 1597
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the tunnel source anylocal command. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. Added an optional keyword “anylocal” to the tunnel source command.
PAGE 1598
61 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1599
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface.
PAGE 1600
description Enter a text description of an uplink-state group. Syntax description text Parameters Defaults text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.
PAGE 1601
Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1602
Related Commands Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. ● downstream — assign a port or port-channel to the uplink-state group as a downstream interface. ● uplink-state-group — create an uplink-state group and enables the tracking of upstream links.
PAGE 1603
enable Enable uplink state group tracking for a specific UFD group. Syntax enable To disable upstream-link tracking without deleting the uplink-state group, use the no enable command. Defaults Upstream-link tracking is automatically enabled in an uplink-state group. Command Modes UPLINK-STATE-GROUP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1604
Example Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1605
Example Version Description 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1606
Usage Information Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1607
Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1608
62 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1609
● Yellow: Lower priority packets that are treated as best-effort. ● Red: Lowest priority packets that are always dropped (regardless of congestion status). Defaults Disabled; Packets with an unmapped DEI value are colored green. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1610
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series.
PAGE 1611
Version Description 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. Usage Information Enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. Related Commands ● vlan-stack compatible — enables stackable VLAN on a VLAN. stack-unit stack-group Configure a stacking group specified by an ID.
PAGE 1612
vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network. Syntax vlan-stack access To remove access port designation, use the no vlan-stack access command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1613
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1614
Parameters c-tag-dot1p value Enter the keyword c-tag-dot1p then the customer dot1p value that is mapped to a service provider do1p value. The range is from 0 to 7. sp-tag-dot1p value Defaults Enter the keyword sp-tag-dot1p then the service provider dot1p value. The range is from 0 to 7. none Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1615
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. C-Series and S-Series accept both bytes of the 2-byte S-Tag TPID. 8.2.1.0 Introduced on the E-Series. 7.
PAGE 1616
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series.
PAGE 1617
interface Vlan 20 no ip address tagged GigabitEthernet 1/42 shutdown DellEMC(conf-if-vl-20)# do show vlan Codes: * - Default VLAN, G - GVRP VLANs Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM Status Description * 1 Inactive 20 Active 100 Active DellEMC(conf-if-vl-20)# Example 2 Q Ports T Gi 1/42 M Gi 1/42 DellEMC(config)# vlan-stack protocol-type 88A8 DellEMC(config)# interface gigabitethernet 3/10 DellEMC(conf-if-gi-3/10)# no shutdown DellEMC(conf-if
PAGE 1618
63 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • ip vrf description ip vrf forwarding ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip vrf Create or delete a customer VRF.
PAGE 1619
The VRF ID is optional. description Specify a name for a customer VRF. Syntax description string To delete the descriptive name for a customer VRF, use the no description string command. Parameters Defaults string Enter a descriptive name for the VRF. None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1620
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. You can attach an interface to either a nondefault VRF or a management VRF.
PAGE 1621
route-map-name (Optional) Enter the name of the route-map to filter the exported routes. You can leak global routes to VRFs. As the global RTM usually contains a large pool of routes, when the destination VRF imports global routes, these routes are duplicated into the VRF's RTM. It is mandatory to use route-maps to filter out leaked routes while sharing global routes with VRFs. Command Modes ● VRP mode ● CONFIGURATION mode Command History Usage Information This guide is platform-specific.
PAGE 1622
NOTE: Use the route-map attribute while importing routes from the global RTM. Route-maps allow you to filter routes at the import end based on the matching criteria that you define in the route-map. Command Modes ● CONFIGURATION ● VRF mode Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1623
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, use the ip route-export tag command without specifying the route-map attribute.
PAGE 1624
Usage Information Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match the protocol and prefix-list options.
PAGE 1625
Related Commands ● ipv6 route-import – imports IPv6 routes from another VRF. redistribute Redistributes leaked or exported routes corresponding to specific protocols. Syntax Parameters redistribute {imported-bgp | import-ospf | import-isis} imported-bgp Enter the keywords imported-bgp to redistribute leaked routes that are learned using the BGP protocol. imported-ospf Enter the keywords imported-ospf to redistribute leaked routes that are learned using the OSPF protocol.
PAGE 1626
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 1627
Usage Information Version Description 9.4(0.0) Introduced on the S–Series. If you do not specify the maximum route limit for a VRF, the VRF has unlimited space that extends to the maximum number of entries allowed for the system. show ip vrf Displays information corresponding to the VRFs that you configure in the system. Syntax Parameters show ip [vrf vrf-name] vrf vrf-name Enter the keyword vrf then the name of the VRF to display information corresponding to that VRF.
PAGE 1628
test1 1 Gi 1/14,16-17 show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax show run vrf vrf-name Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 1628 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1629
64 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1630
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1631
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1632
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link. You can also configure the VLANs you want to exclude from the VLT proxy gateway.
PAGE 1633
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1634
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The proxy-gateway feature may go operationally down for any of the following reasons: ● ● ● ● LLDP is globally disabled.
PAGE 1635
65 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1636
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} Parameters Defaults ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1637
clear vlt statistics Clear the VLT operation statistics. Syntax Parameters clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP.
PAGE 1638
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax delay-restore Parameters Defaults delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1639
This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap). Defaults 60 seconds Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1640
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. LACP on the VLT ports (on a VLT switch or access device), which are members of the VLT, are not brought up until the VLT domain is recognized on the access device.
PAGE 1641
Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1642
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan option. 8.3.8.0 Introduced on the S4810. To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option.
PAGE 1643
peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 65535. The default value is infinity. Command Modes VLT DOMAIN (conf-vlt-domain) Default Infinity Command History This guide is platform-specific.
PAGE 1644
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1645
Usage Information Example (Brief) Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell EMC Networking OS version number. VLT version numbers begin with odd numbers.
PAGE 1646
Example Version Description 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays counter information.
PAGE 1647
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) If you do not add a parameter such as arp or mac, the output displays all the counters.
PAGE 1648
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1649
-----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.2) VLAN 15 DellEMC# --------VLAN 6 gi 1/5 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show mismatch in VXLAN instance parameters. 9.10(0.
PAGE 1650
Example for Q-in-Q implementation over VLT DellEMC#show vlt mismatch Domain -----Parameters Local Peer ----------------PB for stp Enabled Disabled Vlan-type-config ---------------Codes:: P - Primary, C - Community, I - Isolated, N - Normal vlan, M Vlan-stack Vlan-ID ------- Local ----- 100 N Peer ---M Port-type-config ---------------Codes:: p - PVLAN Promiscuous port, h - PVLAN Host port, t - PVLAN Trunk port, mt - Vlan-stack trunk port, mu - Vlan-stack access port, n Normal port Vlt Lag ------128 Lo
PAGE 1651
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1652
Related Commands Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Added parameters multicast and ndp 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1653
Reg Response Sent: 1 Reg Response Rcvd: 0 Route updates sent to Peer: 0 Route updates rcvd from Peer: 0 Route update pkts sent to Peer: 0 Route update pkts rcvd from Peer: 0 VLT NDP Statistics -------------------NDP NA VLT Tunnel Pkts sent:16 NDP NA VLT Tunnel Pkts Rcvd:46 NDP NA Non-VLT Tunnel Pkts sent:0 NDP NA Non-VLT Tunnel Pkts Rcvd:0 Ndp-sync Pkts Sent:144 Ndp-sync Pkts Rcvd:105 Ndp Reg Request sent:25 Ndp Reg Request rcvd:24 show vlt statistics igmp-snoop Displays the informational packets and IGMP
PAGE 1654
system-mac Reconfigure the default MAC address for the domain. Syntax system-mac mac-address Parameters Defaults mac-address Enter the system MAC address for the VLT domain. Not configured. Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1655
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1656
Usage Information The VLT domain ID must be the same between the two VLT devices. If the domain ID is not the same, a syslog message generates and VLT does not launch. Related Commands ● show vlt brief — display the delay-restore value. vlt-peer-lag port-channel Associate the port channel to the corresponding VLT peer port channel for the VLT connection to an attached device.
PAGE 1657
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S6000. 9.3(0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 1658
66 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1659
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1660
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax clear counters vrrp [vrrp-id] [ipv6] Parameters vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1661
between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups.
PAGE 1662
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group. Syntax description text To delete a VRRP group description, use the no description command. Parameters Defaults text Enter a text string up to 80 characters long.
PAGE 1663
To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1664
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1665
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command.
PAGE 1666
If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration. Syntax show config [verbose] Parameters verbose (OPTIONAL) Enter the keyword verbose to view all the VRRP group configuration information, including default information. Command Modes VRRP Command History Example This guide is platform-specific.
PAGE 1667
Parameters vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups. interface type (OPTIONAL) Enter the following keywords and the interface information: ● For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1668
Item Description ● Y = Preempt is enabled. ● N = Preempt is not enabled. Example (Brief) Usage Information State Displays the operational state of the interface using one of the following: ● NA/IF (the interface is not available). ● MASTER (the interface associated with the MASTER router). ● BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router.
PAGE 1669
Example DellEMC> show vrrp -----------------GigabitEthernet 1/3, VRID: 1, Net: 10.1.1.253 VRF: 0 default State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.252 Authentication: (none) Tracking states for 1 interfaces: Up GigabitEthernet 1/17 priority-cost 10 -----------------GigabitEthernet 1/4, VRID: 2, Net: 10.1.2.
PAGE 1670
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 7.6.1.0 Introduced on the S-Series (S50 only). 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1671
Usage Information Version Description 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when you configure a virtual IP address. When you delete the virtual address, the VRRP group stops sending VRRP packets. A system message appears after you enter or delete the virtual-address command.
PAGE 1672
vrrp delay reload Set the delay time for VRRP initialization after a system reboot. Syntax vrrp delay reload seconds Parameters Defaults seconds Enter the number of seconds for the delay. The frange is from 0 to 900 (0 indicates no delay). 0 Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1673
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1674
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. You can use the both command to migrate from VRRPv2 to VRRPv3. When you set the VRRP protocol version to both, the switch sends only VRRPv3 advertisements but can receive either VRRPv2 or VRRPv3 packets.
PAGE 1675
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.9(0.0) Added support to clear the interface configurations corresponding to a range of ports. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1676
bfd Enter the keyword bfd to enable debugging of all VFFP BFD interactions. database Enter the keyword database to display changes related to group, prefix, and interface entries in the VRRP table. packets Enter the keyword packets to enable debugging of VRRP control packets. state Enter the keyword state to enable debugging of VRRP state changes. timer Enter the keyword timer to enable debugging of the VRRP timer.
PAGE 1677
brief (OPTIONAL) Enter the keyword brief to view a table of information on the VRRP groups. vrf vrf-name Enter the keyword vrf then the name of the VRF to view IPv6 VRRP groups corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1678
Line starting with Description Virtual IP address Displays the virtual IP address of the VRRP router to which the interface is connected. Tracking states... Displays information on the tracked interfaces or objects configured for a VRRP group (track command), including: ● UP or DOWN state of the tracked interface or object (Up or Dn). ● Interface type and slot/port or object number, description, and time since the last change in the state of the tracked object.
PAGE 1679
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.2.0 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when you configure a link-local virtual IP address. When you delete the virtual address, the VRRP group stops sending VRRP packets. ● When you do not load the VRF microcode in the CAM, the VRID for a VRRP group is the same as the VRID number configured with the vrrp-group or vrrp-ipv6-group commands.
PAGE 1680
67 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1681
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax Parameters Defaults crypto ca-cert install path path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1682
● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1683
email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect. For self-signed certificates, if validity is not specified, it defaults to 3650 days, or 10 years. length length (OPTIONAL) Enter the keyword length followed by a bit length value.
PAGE 1684
Parameters cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored. Following are example of a path that you can specify: flash://certs/s4810-001-request.crtand usbflash:/certs/s4810-001-cert.
PAGE 1685
If the system is in non-FIPS mode, the certificate will be installed as the non-FIPS certificate. When FIPS mode is enabled/disabled, the certificates (and keys) are switched by the system. Related Commands ● crypto ca-cert install crypto x509 ocsp Configures the OCSP behavior. Syntax Parameters Defaults crypto x509 ocsp [nonce] [sign-requests] nonce Enter the keyword nonce to use the nonce feature for the OCSP requests to OCSP responder communication.
PAGE 1686
Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Related Commands Version Description 9.11.0.0 Introduced this command.
PAGE 1687
tcp Enter the keyword tcp to enable TCP. udp Enter the keyword udp to enable UDP. vrf vrf-name Enter the keyword vrf followed by the name of the VRF. sha1 fingerprint Enter the keyword sha1 followed by the finger print. This option is only available when the secure option is configured. This new option enables the Syslog feature to compare the received certificate’s sha-1 fingerprint against this configured sha-1 fingerprint.
PAGE 1688
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin When you use this command, the device maps the current certificate context in the certificate store to a CA certificate through the subject key identifier field. The subject key identifier field contains the SHA-1 hash of the CA’s public key. This configuration provides a way to uniquely identify a CA and associate it with any CA-specific settings.
PAGE 1689
Related Commands ● crypto x509 ocsp ocsp-server prefer Configures OCSP responder preference. You can configure the preference or order that the CA or a device should follow while contacting multiple OCSP responders. Syntax ocsp-server prefer Defaults None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1690
show crypto cert Displays the certificate information that is specified. Syntax show crypto cert {path} Parameters Defaults path (OPTIONAL) Enter the path to a local file where a certificate chain is stored in PEM format. If a path is not specified, display the certificate that is currently installed on the system. None. Command Modes EXEC Privilege Command History This guide is platform-specific.