Administrator Guide

41:Task(tUsrRoot): [ 697608]33:SS DRV DEBUG: Unit 0 : Soc Reset
Complete
42:Task(tUsrRoot): [ 693327]33:SS DRV DEBUG: Unit 0 : Soc Misc Init
Complete
43:Task(tUsrRoot): [ 770793]34:SS DRV DEBUG: Unit 0 : Soc MMU Init
Complete
44:Task(tUsrRoot): [ 4455907]38:SS DRV DEBUG: Unit 0 : Soc BCM
INitComplete
45:Task(tUsrRoot): [ 81]38:SS DRV DEBUG: Unit 0: Basic Inits
complete
46:Task(tUsrRoot): [ 32839]39:SS DRV DEBUG:
bcmDrvSwitchTypeChipInitSettings complete for unit 0
47:Task(tUsrRoot): [ 127018]39:SS DRV DEBUG: Initializing Stack port
unit 0 port 54
48:Task(tUsrRoot): [ 200703]39:SS DRV DEBUG: Initializing Stack port
unit 0 port 55
49:Task(tUsrRoot): [ 199953]39:SS DRV DEBUG: Port Setup Done
50:Task(tUsrRoot): [ 2938047]42:SS DRV DEBUG: QOS Setup Done
51:Task(tUsrRoot): [ 232921]SS DRV ERR: BCM API Invocation Error(Vlan
already Exists) - Error(-8, Entry exists)
52:Task(tUsrRoot): [ 590818]43:SS DRV DEBUG: S_SERIES_STACK: Waiting
on stack discovery
53:Task(tUsrRoot): [ 8680680]51:SS DRV DEBUG: bcmDrvPostSettings Setup
Done
54:Task(tUsrRoot): [ 562]=========================================
55:Task(tUsrRoot): [ 51]sysDrvLoggerFreezeTop: Top of Log Frozen.
56:Task(tUsrRoot): [ 40]===== FREEZE BY REQUEST =================
57:Task(tUsrRoot): [ 39]=========================================
58:Task(tUsrRoot): [ 53]51:SS DRV DEBUG: bcmDrvInit Done
59:Task(tUsrRoot): [ 67]51:SS DRV DEBUG: bcmDrvInit: Returning,
Time taken 20131916 micro-secs
60:Task(ifagt_1): [ 3447148]SS DRV ERR: BCM API Invocation
Error(bcm_phy84740_pmad_reg_get failed
61:Task(ifagt_1): [ 1070425]SS DRV ERR: BCM API Invocation
Error(bcm_phy84740_pmad_reg_get failed (<- repeated 9 times)
62:Task(ifagt_1): [ 1070425]56:SS DRV DEBUG:
halOpticsUpdateSerialIdInfoUpdate: Update Serial ID Info for XFP48
63:Task(envmgr): [ 1561704]EEPROM LIB ERR: decipherPpId:371 Invalid
ppId[] size[0]
64:Task(ifagt_1): [ 3351519774]EEPROM LIB ERR: decipherPpId:371 Invalid
ppId[] size[0] (<- repeated 1 times)
65:Task(ifagt_1): [ 3351519774]SS DRV ERR: BCM API Invocation
Error(bcm_phy84740_pmad_reg_get failed
show logging kernellog
Display the kernel log for the specified hardware component.
C9000 Series
Syntax
show logging kernellog {cp | rp | linecard slot-id | pe pe-id stack unit
unit-number}
From a PE console, use show logging kernellog stack-unit unit number to display the
kernel logging information for a specified stack-unit.
Parameters
cp Enter the keyword cp to display the kernel log for the Control Processor on the
switch.
rp Enter the keyword cp to display the kernel log for the Route Processor on the
switch.
linecard slot-id Enter the linecard slot-id parameters to specify the line-card ports for
which you want to display the kernel log. The range of line-card slot IDs is from 0
to 2.
1646 Simple Network Management Protocol (SNMP) and Syslog