Dell Command Line Reference Guide for the S4048–ON System 9.14.2.8 September 2020 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: About this Guide.........................................................................................................43 Objectives........................................................................................................................................................................... 43 Audience..............................................................................................................................................................................
asf-mode............................................................................................................................................................................. 88 banner exec........................................................................................................................................................................ 89 banner login....................................................................................................................................
show environment........................................................................................................................................................... 136 show inventory................................................................................................................................................................. 137 show login statistics.......................................................................................................................................
remark...........................................................................................................................................................................190 show config................................................................................................................................................................. 192 Common IP ACL Commands....................................................................................................................................
Route Map Commands.................................................................................................................................................. 249 continue.......................................................................................................................................................................249 description.........................................................................................................................................................
deny icmp (for Extended IP ACLs).............................................................................................................................290 deny ether-type (for Extended MAC ACLs).............................................................................................................291 deny (for Standard MAC ACLs)..................................................................................................................................292 deny (for Extended MAC ACLs).........
neighbor bfd disable....................................................................................................................................................... 346 show bfd neighbors........................................................................................................................................................ 347 vrrp bfd neighbor................................................................................................................................................
neighbor add-path..................................................................................................................................................... 391 neighbor advertisement-interval........................................................................................................................... 392 neighbor advertisement-start................................................................................................................................ 393 neighbor allowas-in..
show ip bgp inconsistent-as................................................................................................................................... 443 show ip bgp neighbors............................................................................................................................................. 445 show ip bgp next-hop..............................................................................................................................................
show ip protocol-queue-mapping................................................................................................................................487 show ipv6 protocol-queue-mapping...........................................................................................................................488 show mac protocol-queue-mapping...........................................................................................................................
dcb pfc-total-buffer-size..............................................................................................................................................529 show running-config dcb-buffer-threshold..............................................................................................................530 service-class buffer shared-threshold-weight......................................................................................................... 531 dcb pfc-queues...................
show ip dhcp conflict............................................................................................................................................... 574 show ip dhcp server................................................................................................................................................. 574 Commands to Configure Secure DHCP.................................................................................................................... 575 arp inspection......
Chapter 16: FIPS Cryptography.................................................................................................. 611 fips mode enable...............................................................................................................................................................611 show fips status................................................................................................................................................................611 show ip ssh..........
show gvrp statistics........................................................................................................................................................651 Chapter 20: High Availability (HA).............................................................................................654 redundancy disable-auto-reboot................................................................................................................................. 654 redundancy force-failover................
errdisable recovery cause....................................................................................................................................... 693 errdisable recovery interval.................................................................................................................................... 693 flowcontrol..................................................................................................................................................................
show management application pkt-fallback-cntr.............................................................................................. 753 Port Channel Commands.............................................................................................................................................. 754 channel-member........................................................................................................................................................754 group.........................
ip domain-list.................................................................................................................................................................... 796 ip domain-lookup............................................................................................................................................................. 797 ip domain-name.........................................................................................................................................
maximum dynamic-routes-ipv6................................................................................................................................... 853 ipv6 address autoconfig................................................................................................................................................ 854 ipv6 address.....................................................................................................................................................................
debug isis update-packets............................................................................................................................................ 893 default-information originate....................................................................................................................................... 894 description..................................................................................................................................................................
show isis interface.......................................................................................................................................................... 938 show isis neighbors.........................................................................................................................................................940 show isis protocol............................................................................................................................................
fefd interval................................................................................................................................................................ 984 fefd mode....................................................................................................................................................................984 fefd reset...................................................................................................................................................
clear ip msdp statistic.................................................................................................................................................. 1023 debug ip msdp................................................................................................................................................................ 1024 ip msdp cache-rejected-sa.....................................................................................................................................
show spanning-tree mst configuration.................................................................................................................... 1058 show spanning-tree msti............................................................................................................................................. 1058 spanning-tree..................................................................................................................................................................
delay........................................................................................................................................................................... 1095 description.................................................................................................................................................................1096 show running-config track................................................................................................................................
ip ospf retransmit-interval...................................................................................................................................... 1141 ip ospf transmit-delay..............................................................................................................................................1142 log-adjacency-changes...........................................................................................................................................
ipv6 ospf bfd all-neighbors....................................................................................................................................1202 ipv6 ospf cost...........................................................................................................................................................1203 ipv6 ospf dead-interval..........................................................................................................................................
no ip pim snooping dr-flood.................................................................................................................................. 1248 show ip pim bsr-router........................................................................................................................................... 1249 show ip pim interface.............................................................................................................................................
description.......................................................................................................................................................................1288 disable.............................................................................................................................................................................. 1289 extend system-id..............................................................................................................................
show qos dot1p-queue-mapping..........................................................................................................................1335 show qos policy-map.............................................................................................................................................. 1335 show qos policy-map-input................................................................................................................................... 1337 show qos policy-map-output..
Chapter 48: Remote Monitoring (RMON)................................................................................. 1383 rmon alarm...................................................................................................................................................................... 1383 rmon collection history.................................................................................................................................................1385 rmon collection statistics........
aaa authentication login......................................................................................................................................... 1426 aaa reauthenticate enable..................................................................................................................................... 1428 access-class..............................................................................................................................................................
dot1x authentication (Interface)..........................................................................................................................1466 dot1x auth-fail-vlan..................................................................................................................................................1467 dot1x auth-server....................................................................................................................................................
ip dhcp snooping vlan.............................................................................................................................................1508 show ip dhcp snooping...........................................................................................................................................1509 Role-Based Access Control Commands..................................................................................................................
snmp-server community........................................................................................................................................ 1546 snmp-server contact.............................................................................................................................................. 1547 snmp-server enable traps......................................................................................................................................
stack-unit priority...........................................................................................................................................................1613 stack-unit provision....................................................................................................................................................... 1613 stack-unit stack-group......................................................................................................................................
address.......................................................................................................................................................................1649 street-address..........................................................................................................................................................1649 territory.......................................................................................................................................................
Chapter 62: Uplink Failure Detection (UFD)............................................................................. 1686 clear ufd-disable............................................................................................................................................................ 1686 debug uplink-state-group............................................................................................................................................ 1687 description...........................
show vlt-proxy-gateway.............................................................................................................................................. 1724 Chapter 66: Virtual Link Trunking (VLT)...................................................................................1726 arp additional-refresh................................................................................................................................................... 1727 back-up destination.....................
vxlan-instance static.....................................................................................................................................................1760 vxlan-vnid......................................................................................................................................................................... 1761 show running-config vxlan...............................................................................................................................
ocsp-server prefer........................................................................................................................................................ 1800 show crypto ca-cert..................................................................................................................................................... 1800 show crypto cert..................................................................................................................................................
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/1 for the interface tengigabitethernet 1/1/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated the command to display the IPV6acloptimized feature on the S6100– ON and Z9100–ON. 9.12(1.
To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command. CONFIGURATION Mode In EXEC Privilege mode, use the configure command to enter CONFIGURATION mode and configure routing protocols and access interfaces. To enter CONFIGURATION mode: 1. Verify that you are logged in to EXEC Privilege mode. 2.
You can return to CONFIGURATION mode by using the exit command. EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode.
To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port[/subport] number.
LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information, see Link Layer Discovery Protocol (LLDP). To enter LLDP mode: 1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode. 2. Enter the protocol lldp command. The prompt changes to include conf-lldp or conf-if-interface-lldp.
To enter MULTIPLE SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree mstp command. The prompt changes to include conf-mstp. You can return to CONFIGURATION mode by using the exit command. OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
2. Enter the protocol gvrp command. The prompt changes to include config-gvrp. You can return to CONFIGURATION mode by using the exit command. RAPID SPANNING TREE (RSTP) Mode To enable and configure RSTP, use RSTP mode. For more information, see Rapid Spanning Tree Protocol (RSTP). To enter RSTP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree rstp command. The prompt changes to include conf-rstp.
ROUTER OSPFV3 Mode To configure OSPF for IPv6, use ROUTER OSPFV3 mode. To enter ROUTER OSPFV3 mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ipv6 router ospf {process-id} command. The prompt changes to include conf-ipv6-router_ospf. You can return to CONFIGURATION mode by using the exit command. ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, see Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1.
2. Enter the vlt domain command, and then the VLT domain number. The prompt changes to include conf-vlt-domain. You can return to CONFIGURATION mode by entering the exit command. VRRP Mode To enable and configure Virtual Router Redundancy Protocol (VRRP), use VRRP mode. For more information, see Virtual Router Redundancy Protocol (VRRP). To enter VRRP mode: 1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command, and then enter the VRRP group ID.
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
primary Enter the keyword primary to specify the primary Dell EMC Networking OS image. secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. system: Enter the keyword system: to use the system image file URL (system). ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system.
cd Change to a different working directory. Syntax Parameters cd [flash: | usbflash:] flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB.
Password to login remote host: Destination file name [sample_file]: Defaults None. Command Modes EXEC Privilege Command History Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. copy http://admin:admin123@10.16.206.77/sample_file flash://sample_file copy Copy one file to another location.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added the nfsmount: parameters that allow you to mount a remote NFS file system. 9.4(0.0) Added the compressed-config parameter. 9.3(0.1) Added the http parameter on the S6000, Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. 8.4.1.
! 4080 bytes successfully copied DellEMC# In this copy scp: flash: example, specifying SCP in the first position indicates that you need to specify the target in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal flash. The source is on a secure server running secure shell (SSH), so you are prompted for the user datagram protocol (UDP) port of the SSH server on the remote host.
usbflash: To delete a file or directory on the external USB flash, enter usbflash:// then the filename or directory name ([usbflash://]filepath). no-confirm (OPTIONAL) Enter the keywords no-confirm to specify that the Dell EMC Networking OS does not require user input for each file prior to deletion. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for NFS mount. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Introduced on S4810 and Z9000. 8.3.19.0 Introduced on S4820T. Include the colon (:) when entering this command. This command checks the specified flash memory for errors. If errors are found, the command recommends that you format the flash.
Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system. username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password. Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Example Related Commands DellEMC# rmdir nfsmount:/nfs-mountpoint/guest Proceed to remove the directory [confirm yes/no]: yes ● mkdir – create a directory. HTTP Copy via CLI Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). Syntax copy http://10.16.206.77/sample_file flash://sample_filecopy flash:// sample_file http://10.16.206.77/sample_file You can copy from the server to the switch and vice-versa.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fan-out, and so forth). When restoring all units in a stack, all the units in the stack are placed into stand-alone mode. When restoring a single unit in a stack, that unit placed in stand-alone mode.
Example (single stack) Example (NvRAM all stack units) Example (NvRAM, single unit) DellEMC# restore factory-defaults stack-unit 1 clear-all ************************************************************** * Warning - Restoring factory defaults will delete the existing * * startup-config and all persistent settings (stacking, fanout, etc.)* * After restoration the unit(s) will be powercycled immediately.
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. E-Series Original command. DellEMC# show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
Example Version Description 7.6.1.0 Introduced on the S-Series 7.5.1.0 Introduced on the C-Series E-Series Original command DellEMC#show file-systems Size(b) 4286574592 2032525312 DellEMC# Command Fields Free(b) 4170424320 590807040 - Feature Type FAT32 USERFLASH unformatted USERFLASH Unknown NFSMOUNT network network network network Flags rw rw rw rw rw rw rw Prefixes flash: fcmfs: nfsmount: ftp: tftp: scp: http: Field Description size(b) Lists the size (in bytes) of the storage location.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
File Management ethernet for the current Ethernet CFM configuration fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current FVRP configuration gvrp for the current GVRP configuration host for the current host configuration hardwaremonitor for hardware-monitor action-on-error settings hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current
qos-policyinput for the current input QoS policy configuration qos-policyoutput for the current output QoS policy configuration radius for the current RADIUS configuration redirect-list for the current redirect-list configuration redundancy for the current RPM redundancy configuration resolve for the current DNS configuration rip for the current RIP configuration rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configura
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for the tunnel and EIS interface types. 9.0.0.0 Added support for the VLT option. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the hardware-monitor option. 7.6.1.
show startup-config Display the startup configuration. Syntax show startup-config Command Modes EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Command Modes EXEC Privilege Command History Command Fields 82 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
upgrade Upgrade the bootflash image or system image of the management unit. Syntax Parameters upgrade boot {all | bootflash—image | bootselector-image} stack-unit {stackunit-number | all} {booted | flash: | ftp: | nfsmount | scp: | tftp: | usbflash:} file-url boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility this command accepts IPv6 host addresses with or without the square brackets. Reload Dell EMC Networking OS after executing this command.
stack-unit stack- Enter the keyword stack-unit and specify the stack-unit ID to sync the image unit-id to that stack-unit. Defaults stack-unit all Enter the keyword stack-unit followed by the keyword all to sync the image on all stack-units. tftp: file-url Enter the keyword tftp: and specify the location of the image file in the format //host-ip/filepath or press Enter to launch a prompt sequence.
1. Upgrade the system image to the new image and configure the primary partition to boot from the new image using the boot system command. 2. Update the startup configuration file with the new set of configurations and then reload the device using the reload command. The new set of configurations are parsed from the startup configuration file and applied to the NVRAM. During the system boot up, the new set of configurations are applied to the system from the updated NVRAM configurations.
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
• • • • • • • • • • • • • • • • • • • • • • show command-history show cpu-traffic-stats show debugging show environment show inventory show login statistics show memory show processes cpu show processes ipc flow-control show processes memory show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit telnet telnet-peer-stack-unit terminal length traceroute undebug all virtual-ip write asf-mode Enable alternate store and forward (ASF) mode and forward packets as soon as a threshol
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P1) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information You must save the configuration and reload the system to implement ASF.
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original Command After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the acknowledgement keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters Defaults c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator. The delineator is a percent character (%). No banner is configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
Usage Information Version Description 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dual-qos. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
clear average-power Reset the average power and average power start time. Syntax Parameters Defaults clear average-power stack-unit {stack-unit-number} stack-unitnumber Enter the stack unit number. None Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode. Syntax Parameters Defaults disable [level] level (OPTIONAL) Enter a number for a privilege level of the Dell EMC Networking OS. The range is from 0 to 15.
Version Description E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax do command Parameters Defaults command Enter an EXEC-level command. none Command Modes ● CONFIGURATION ● INTERFACE Command History Usage Information Example 98 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
DellEMC(conf-if-te-5/1)# DellEMC(conf-if-te-5/1)# do reload System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Syntax Parameters Defaults enable [level] level (OPTIONAL) Enter a number for a privilege level of Dell EMC Networking OS. The range is from 0 to 15.
enable cpu-clock-monitor Enables Intel CPU LPC (Low Pin Count) clock-failure monitoring. Syntax enable cpu-clock-monitor To disable this feature, use the no enable cpu-clock-monitor command. Parameters None Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
Usage Information Version Description 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. To enable polling and to configure the polling frequency, use this command. enable xfp-power-updates Enable 10–gigabit small form-factor pluggable (XFP) power updates for SNMP. Syntax Parameters Defaults enable xfp-power-updates interval seconds interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds.
● ● ● ● ● ● ● ● Command History Related Commands ACCESS-LIST PREFIX-LIST AS-PATH ACL COMMUNITY-LIST ROUTER OSPF ROUTER RIP ROUTER ISIS ROUTER BGP This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The hostname is used in the prompt. ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command.
Version Description 8.1.1.0 Introduced on E-Series 7.6.1.0 Support added for S-Series 7.5.1.0 Introduced on C-Series ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses.
● 7 (seven) for a hidden text password password Defaults Enter a string up to 40 characters as the password. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Use this command to make the FTP clients VRF-aware. The VRF name that you specify is used by the FTP client to reach the FTP server. If no VRF name is specified, then the default VRF is used. ip telnet server enable Enable the Telnet server on the switch.
ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF. Syntax ip telnet server vrf {vrf-name | any | management} To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters Defaults vrf-name Enter the vrf-name to specify the VRF that is used by the TELNET server. any Enter the keyword any to enable server from any VRF.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For VLAN interface, enter the keyword vlan then a number from 1 to 4094.
To undo the TELENT client configuration, use the ip telnet [vrf vrf-name] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TELENT client. Disabled Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant FTOS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards. 8.2.1.0 Increased number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series.
Usage Information Use this command to make the TFTP clients VRF aware. The VRF name that you specify is used by the TFTP client to reach the TFTP server. If no VRF is specified, then the default VRF is used. Related Commands ● ftp-server topdir — sets the directory to be used for incoming FTP connections. ● ftp-server username — sets a username and password for incoming FTP connections. line Enable and configure console and virtual terminal lines to the system.
Related Commands ● access-class — restricts the incoming connections to a particular IP address in an IP access control list (ACL). ● password — specifies a password for users on terminal lines. login concurrent-session Configures the limit of concurrent sessions for each user on console and virtual terminal lines.
When you try to log in, the following message appears with all your existing concurrent sessions, providing an option to close any one of the existing sessions: $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'. Login: admin Password: Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. Only the system and security administrators can configure login activity tracking and view the login activity details of other users.
motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
NOTE: The :: notation specifies successive hexadecimal fields of zeros. count Enter the number of echo packets to be sent. The default is 5. ● number: from 1 to 2147483647 ● continuous: transmit echo request continuously datagram size Enter the ICMP datagram size. The range is from 36 to 15360 bytes. The default is 100. timeout Enter the interval to wait for an echo reply before timing out. The range is from 0 to 3600 seconds. The default is 2 seconds.
vrf vrf-name Defaults Enter the keyword vrf followed by the name of the VRF to test connectivity to the VRF. None. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
Example (IPv4) Symbol Description U A destination unreachable error PDU was received. Q Source quench (destination too busy). M Could not fragment. ? Unknown packet type. & Packet lifetime exceeded. DellEMC# ping 172.31.1.255 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2 seconds: Reply to request 1 from 172.31.1.208 0 ms Reply to request 1 from 172.31.1.216 0 ms Reply to request 1 from 172.31.1.205 16 ms :: Reply to request 5 from 172.31.1.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Added the optional dell-diag and onie parameters. Introduced the no-confirm option. Usage Information 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
The following example shows how to reload the system into ONIE prompt and enter the install mode directly: DellEMC#reload onie install Proceed with reload [confirm yes/no]: yes reload-type Allows you to configure the boot-type or secure-erase for the next reload. Syntax reload-type Parameters N/A Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
Example DellEMC(conf-reload-type)#boot-type warmboot DellEMC(conf-reload-type)#end Dell# secure-erase Allows you to perform an fstrim on the flash disk during the next reload. Syntax secure-erase To disable secure-erase, use the no secure-erase command. Defaults Enabled. Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series.
Usage Information Version Description 9.14(1.5) Added support for UTC time format. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.
-- Chassis Vlan Cam ACL -Current Settings(in block sizes) 1 block = 256 entries VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 -- stack-unit 1 -Current Settings(in block sizes) VlanOpenFlow : 1 VlanIscsi : 0 VlanAclOpt : 1 VlanHp : 1 VlanFcoe : 1 VlanNlbClstr : 0 show command-history Display a buffered log of all commands all users enter along with a time stamp.
Example Example 1: Default configuration service timestamps log datetime or service timestamps log datetime localtime DellEMC#show clock 15:42:42.804 IST Fri May 17 2019 DellEMC(conf)#service timestamps log datetime DellEMC# show command-history [May 17 15:38:55]: CMD-(CLI):[service timestamps log datetime]by default from console [May 17 15:41:40]: CMD-(CLI):[write memory]by default from console - Repeated 1 time.
[May 17 [May 17 [May 17 [May 17 console 15:55:00]: 15:55:12]: 15:55:22]: 15:55:27]: CMD-(CLI):[show CMD-(CLI):[show CMD-(CLI):[show CMD-(CLI):[show logging]by default from console clock]by default from console running-config]by default from console command-history]by default from show cpu-traffic-stats View the CPU traffic statistics.
NOTE: After debugging is complete, use the no debug cpu-traffic-stats command to shut off traffic statistics collection.
Example DellEMC# show debug Generic IP: IP packet debugging is on for ManagementEthernet 1/1 Port-channel 1-2 Port-channel 5 tenGigabitEthernet 4/1-4/3,4/5-4/6,4/10-4/11,20 TenGigabitEthernet 5/1-5/3,5/5-5/6,5/10-5/11,15,17,19,21 ICMP packet debugging is on for TenGigabitEthernet 5/1,5/2,5/4,5/6,5/8,5/10,5/12,5/14,5/16 DellEMC# show environment View system component status (for example, temperature or voltage).
Usage Information Example (all) Version Description 7.8.1.0 The output of the show environment fan command for the S Series is changed to display fan speeds instead of showing the fan status as up or down. The following example shows the output of the show environment command.
Parameters Defaults media slot (OPTIONAL) Enter the keyword media then the stack ID of the stack member for which you want to display pluggable media inventory. NOTE: This parameter is available but not supported in Dell EMC Networking Operating System version 8.3.11.4. Because stacking is not supported, if you use this parameter, the output displays “Media not present or accessible” (refer to the Usage Information section).
-----------------------------------------------------------------------------2 1 SFP 1000BASE-SX U8706GR Yes 2 2 SFP 1000BASE-SX U8D0PTJ Yes 2 3 SFP 1000BASE-SX PLL4QZG Yes 2 4 SFP 1000BASE-SX PGP2DLH Yes 2 5 SFP 1000BASE-SX PGE3CEG Yes 2 6 Media not present or accessible 2 7 SFP+ 10GBASE-CU2M APF1138003969J Yes 2 8 SFP+ 10GBASE-CU2M APF113800395JP Yes 2 9 Media not present or accessible 2 10 Media not present or accessible 2 11 SFP+ 10GBASE-SR AJG0FFG Yes 2 12 Media not present or accessible 2 13 Media not
keyword, the system displays the number of failed login attempts by a specific user in the last 30 days or the custom defined time period Defaults None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
-----------------------------------------------------------------User: admin1 Last login time: 12:49:19 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
Related Commands ● login statistics — enable and configure user login statistics on console and virtual terminal lines. ● login concurrent-session — configures the limit of concurrent sessions for each user on console and virtual terminal lines. show memory View current memory usage on the switch. Syntax show memory [stack-unit id] Parameters stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack unit ID to display memory information on the designated stack member.
Parameters management-unit (OPTIONAL) Display processes running in the control processor. The 1-99 variable [ 1-99 | details] sets the number of tasks to display in order of the highest CPU usage in the past five (5) seconds. Add the keyword details to display all running processes (except sysdlp). Refer to Example (management-unit). stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack member ID.
CPU utilization of sysdlp for five seconds: 2%/0%; one minute: 3%; PID Runtime(ms) Invoked uSecs 5Sec 1Min Process 0xbb773000 5950 595 10000 1.00% 2.25% tExcTask 0xbab2a000 4030 403 10000 1.00% 1.33% frrpagt 0xbacf3000 10 1 10000 0.00% 0.00% F10StkMgr 0xbad0c000 710 71 10000 0.00% 0.00% lcMgr 0xbad24000 30 3 10000 0.00% 0.00% 0 dla 0xbad44000 50 5 10000 0.00% 0.00% sysAdmTsk 0xbad58000 650 65 10000 0.00% 0.00% timerMgr 0xbad6e000 50 5 10000 0.00% 0.00% 0 PM 0xbad85000 1190 119 10000 0.00% 0.
details | Detail CPU utilization Pipe through a command DellEMC# show processes cpu management-unit CPUID 5sec 1min 5min -------------------------------------------------CORE 0 9.54 9.92 12.82 CORE 2 10.74 11.56 14.31 Overall 10.14 10.74 13.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
● After retrying a defined number of times, the SWP-2-NOMORETIMEOUT timeout message is generated. ● In the S-Series example, a retry (Retries) value of zero indicates that the SWP mechanism reached the maximum number of retransmissions without an acknowledgement.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.7.1.0 Added the management-unit option. 7.6.1.0 Introduced on the S-Series.
sysAdmTsk 33216 tFib4 1943960 aclAgent 90770 ifagt_1 21318 dsagt 6504 MacAgent 269778 DellEMC# Example (managementunit) 0 0 16564 16564 0 0 33216 33216 1943960 1943960 74206 74206 21318 4754 6504 6504 269778 269778 DellEMC# show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249
Usage Information Version Description 9.13(0.0) Introduced on the S3048–ON, S3100 series, S4048–ON, S4048T–ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, C9010, MXL, M-IOA, and FN-IOM. You can use the show reset-reason without the stack-unit option to view the reason for the last system reboot of the local system.
----------------------------------------------------------------------------------stack-unit 1 Reboot by Software 11/05/2017-09:04 stack-unit 2 Reboot by Software 11/05/2017-09:04 stack-unit 3 Cold Reset N/A stack-unit 4 N/A N/A stack-unit 5 N/A N/A stack-unit 6 N/A N/A show software ifm Display interface management (IFM) data.
Example Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced for the C-Series and S-Series.
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, use the show reload-type command. Modified the show system stack-unit command output to support Piece Part ID (PPID). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.
----------1 1 up 1 2 up 1 3 up up up up 7072 7021 7021 up up up 7021 6971 7021 Speed in RPM show tech-support Display a collection of data from other show commands, necessary for Dell EMC Networking technical support to perform troubleshooting. Syntax show tech-support [stack-unit unit-id | page] Parameters stack-unit (OPTIONAL) Enter the keywords stack-unit to view CPU memory usage for the stack member designated by unit-id.
The save option works with other filtering commands. This allows you to save specific information of a show command. The save entry must always be the last option.
Dell EMC Operating System Version: 2.0 Dell EMC Application Software Version: 9.14(0.0) Copyright (c) 1999-2018 by Dell Inc. All Rights Reserved. Build Time: Thu Jun 28 10:15:47 2018 Build Path: /build/build02/SW/SRC Dell EMC Networking OS uptime is 1 minute(s) System image file is "system://A" System Type: S4048-ON Control Processor: Intel Rangeley with 2 Gbytes (2127560704 bytes) of memory, core(s) 2. 8G bytes of boot flash memory. 1 54-port TE/FG (SK-ON) 48 Ten GigabitEthernet/IEEE 802.
Copyright (c) 1999-2018 by Dell Inc. All Rights Reserved. Build Time: Thu Jun 28 10:15:47 2018 Build Path: /build/build02/SW/SRC Dell EMC Networking OS uptime is 1 minute(s) System image file is "system://A" System Type: S4048-ON Control Processor: Intel Rangeley with 2 Gbytes (2127560704 bytes) of memory, core(s) 2. 8G bytes of boot flash memory. 1 54-port TE/FG (SK-ON) 48 Ten GigabitEthernet/IEEE 802.3 interface(s) 6 Forty GigabitEthernet/IEEE 802.
telnet Connect through Telnet to a server. The Telnet client and server in Dell EMC Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router. NOTE: The Telnet server and client are VRF-aware. Using the vrf parameter in this command, you can make a Telnet server or client to listen to a specific VRF. This capability enables a Telent server or client to look up the correct routing table and establish a connection.
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Added support for source-interface for link-local IPv6 addressing. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series (IPv6). Increased the number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. terminal length Configure the number of lines displayed on the terminal screen. Syntax terminal length screen-length Parameters Defaults screen-length Enter a number of lines. Entering zero causes the terminal to display without pausing. The range is from 0 to 512.
traceroute View a packet’s path to a specific device. Syntax Parameters traceroute {host | vrf instance | ip-address | ipv6-address} host Enter the name of device. vrf instance (Optional) E-Series Only: Enter the keyword vrf then the VRF Instance name. ip-address Enter the IP address of the device in dotted decimal format. ipv6-address Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
Usage Information When you enter the traceroute command without specifying an IP address (Extended Traceroute), you are prompted for a target and source IP address, timeout (in seconds) (default is 5), a probe count (default is 3), minimum TTL (default is 1), maximum TTL (default is 30), and port number (default is 33434). To keep the default setting for those parameters, press the ENTER key. For IPv6, you are prompted for a minimum hop count (default is 1) and a maximum hop count (default is 64).
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information You can configure both IPv4 and IPv6 virtual addresses simultaneously, but only one of each.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The write memory command saves the running-configuration to the file labeled startup-configuration.
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
• • • • • dot1x mac show show show tx-period dot1x cos-mapping interface dot1x interface dot1x profile debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x.
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: ● Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). ● Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command).
Related Commands ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9000 Series.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series.
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode.
Parameters Defaults force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. None Command Modes Auto Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9010. The dot1x profile command configures a dot1x profile to define a list of trusted supplicant MAC addresses. Maximum number of dot1x profiles is limited to 10.
dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command. Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which reauthentication is initiated. The range is from 1 to 31536000 (one year). The default is 3600 (1 hour).
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. When you configure the dot1x server-timeout value, take into account the communication medium used to communicate with an authentication server and the number of RADIUS servers configured.
● Ensure that no configured profile exists at the time of configuring the static-mab command. ● Use this command in Interface Batch Mode to enable static MAB in a dual-homing setup. Example DellEMC(conf)#do show dot1x interface twentyFiveGigE 1/41 802.
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command.
mac Configure a list of supplicant MAC addresses for dot1x profile represented with a profile-name. Syntax [no] mac {mac-address1 mac-address2… mac-address6} Parameters Defaults mac-address1 mac-address2 … mac-address6 Enter the keyword mac and type the 48– bit MAC addresses using the H.H.H format. A maximum of 6 MAC addresses are allowed. None Command Modes DOT1X PROFILE CONFIG (conf-dot1x-profile) CONFIGURATION TERMINAL BATCH Command History Usage Information This guide is platform-specific.
Command Modes ● EXEC ● EXEC privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
4 5 6 7 DellEMC# 3 2 1 0 show dot1x interface Display the 802.1X configuration of an interface. Syntax show dot1x interface interface [mac-address mac-address] Parameters interface Enter one of the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
Example DellEMC# show dot1x interface tengigabitethernet 1/32 802.
Re-Authentication: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: Disable Enable 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Auth Status: Untagged VLAN id: Auth PAE St
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
• • • • • • • • • • • • • permit tcp (for Extended IP ACLs) seq arp (for Extended MAC ACLs) seq ether-type (for Extended MAC ACLs) seq (for IP ACLs) seq (for IPv6 ACLs) permit udp (for IPv6 ACLs) permit tcp (for IPv6 ACLs) permit icmp (for IPv6 ACLs) permit (for IPv6 ACLs) deny udp (for IPv6 ACLs) deny tcp (for IPv6 ACLs) deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode.
Related Commands ● show config — display the current ACL configuration. show config Display the current ACL configuration. Syntax show config Command Modes ● ● ● ● Command History Example 192 CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Common IP ACL Commands The following commands are available within both Ingress and Egress IP ACL modes (Standard and Extended) and do not have mode-specific options. When an ACL is created without a rule and then is applied to an interface, ACL behavior reflects an implicit permit. The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line.
Usage Information When you use the access-class access-list-name command without specifying the ipv4 or ipv6 attribute, both IPv4 as well as IPv6 rules that are defined in that ACL are applied to the terminal. This method is a generic way of configuring access restrictions. To be able to filter access exclusively using either IPv4 or IPv6 rules, use either the ipv4 or ipv6 attribute along with the access-class access-list-name command.
ip access-group Assign an IP access list (IP ACL) to an interface. Syntax ip access-group access-list-name {in | out} [implicit-permit] [vlan vlanid] [layer3] [vrf vrf-name] To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id][layer3] [vrf vrf-name] command. Parameters Defaults access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. You can assign one ingress ACL and one egress ACL to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14.2.8 Introduced on all platforms. You can assign one ingress ACL and one egress ACL to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces.
ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Updated the show command output to include monitor option. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
show ip access-lists Display all of the IP ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/ mismatches against each ACL entry displayed. Syntax show ip access-lists [access-list-name] [interface interface] [in | out] [vrf vrf-name] Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters.
● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command. Parameters Defaults source Enter the IP address in dotted decimal format of the network from which the packet was sent. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host and then enter the IP address to specify a host IP address only.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry.
lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide.
resequence access-list Re-assign sequence numbers to entries of an existing access-list. Syntax Parameters resequence access-list {ipv4 | ipv6 | mac} {access-list-name StartingSeqNum Step-to-Increment} ipv4 | ipv6 | mac Enter the keyword ipv4or mac to identify the access list type to resequence. access-list-name Enter the name of a configured IP access list. Defaults StartingSeqNum Enter the starting sequence number to resequence. The range is from 0 to 4294967290.
seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ipaddress}} [count [byte] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To delete a filter, use the no seq sequence-number command. Parameters Defaults sequencenumber Enter a number from 0 to 4294967290. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
deny Configure a filter that drops IP packets meeting the filter criteria. Syntax deny {ip | ip-protocol-number} {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator][count [byte] | log] [dscp value] [order] [monitor] [fragments] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator] [dscp] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(2.0P0) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255.
Defaults fragments Enter the keyword fragments to use ACLs to control packet fragments. monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see Flow-based Monitoring in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
The C-Series and S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands ● deny — assign a filter to deny IP traffic. ● deny tcp — assign a filter to deny TCP traffic. ip access-list extended Name (or select) an extended IP access list (IP ACL) based on IP addresses or protocols.
Example Related Commands DellEMC(conf)# ip access-list extended TESTListEXTEND DellEMC(config-ext-nacl)# ● ip access-list standard — configure a standard IP access list. ● show config — display the current configuration. permit To pass IP packets meeting the filter criteria, configure a filter.
interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. no-drop Defaults Enter the keywords no-drop to match only the forwarded packets. Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.
permit tcp To pass TCP packets meeting the filter criteria, configure a filter. Syntax permit tcp {source mask | any | host ip-address} [bit] [operator port [port]] {destination mask | any | host ip-address} [bit] [ttl operator] [dscp] [operator port [port]] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
● ● ● ● Defaults 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes.
Usage Information Version Description 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only.
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit udp {source mask | any | host ip-address} {destination mask | any | host ip-address command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
3 4 5 6 7 8 0001000000000000 0001100000000000 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111100000000000 1111110000000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 4096 6144 7168 7680 7936 8000 6143 7167 7679 7935 7999 8000 2048 1024 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. When all sequence numbers are exhausted, this feature permits re-assigning a new sequence number to entries of an existing access-list.
portnumber (OPTIONAL) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● ● ● ● 23 = Telnet 20 and 21 = FTP-DATA and FTP 25 = SMTP 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent. ttl Enter the keyword ttl to permit or deny a packet based on the time to live value. The range is from 1 to 255.
Usage Information Version Description 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
Common MAC Access List Commands The following commands are available within both MAC ACL modes (Standard and Extended) and do not have mode-specific options. These commands allow you to clear, display, and assign MAC ACL configurations. The platform supports both Ingress and Egress MAC ACLs. The MAC ACL can be applied on Physical, Port-channel and VLAN interfaces. As per the specified rules in the ACL, the traffic on the interface/ VLAN members or Port-channel members will be permitted or denied.
Parameters access-list-name Enter the name of a configured MAC access list, up to 140 characters. NOTE: This option is available only with the keyword in option. vlan vlan-range (OPTIONAL) Enter the keyword vlan and then enter a range of VLANs. The range is from 1 to 4094 (you can use IDs 1 to 4094). NOTE: This option is available only with the keyword in option. optimized Enter the keyword optimized to enable ACL optimization. in Enter the keyword in to configure the ACL to filter incoming traffic.
Usage Information You can assign one ingress ACL and one egress ACL (standard or extended) to an interface. Related Commands ● mac access-list standard — configure a standard MAC ACL. ● mac access-list extended — configure an extended MAC ACL. show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed.
show mac accounting access-list Display MAC access list configurations and counters (if configured). Syntax show mac accounting access-list access-list-name interface interface in | out Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters.
Example DellEMC# show mac accounting access-list TestMac interface tengigabitethernet 1/8 in Ingress Standard mac access-list TestMac on TenGigabitEthernet 1/89 Total cam count 2 seq 5 permit aa:aa:aa:aa:00:00 00:00:00:00:ff:ff count (0 packets) seq 10 deny any count (20072594 packets) DellEMC# Standard MAC ACL Commands When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
Parameters Defaults any Enter the keyword any to specify that all routes are subject to the filter. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match). count (OPTIONAL) Enter the keyword count to count packets processed by the filter.
NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands ● deny — configure a filter to drop packets. ● permit — configure a filter to forward packets. Extended MAC ACL Commands When an access-list is created without any rule and then applied to an interface, ACL behavior reflects implicit permit. The following commands configure Extended MAC ACLs.
Defaults byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. log (OPTIONAL) Enter the keyword log to include ACL messages in the log. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
mac access-list extended Name a new or existing extended MAC access control list (extended MAC ACL). Syntax mac access-list extended access-list-name [cpu-qos] To delete a MAC access list, use the no mac access-list extended access-list-name command. Parameters access-list-name Enter a text string as the MAC access list name, up to 140 characters. cpu-qos Defaults Enter the keywords cpu-qos to assign this ACL to control plane traffic only (CoPP).
DellEMC(config-ext-macl)# exit DellEMC(conf)# do show mac accounting access-list snickers interface tengig 1/17 in Extended mac access-list snickers on TenGigabitEthernet 1/17 seq 10 permit any any ev2 eq 800 count bytes (559851886 packets 191402152148 bytes) seq 20 permit any any ev2 eq 806 count bytes (74481486 packets 5031686754 bytes) seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands ● mac access-list standard — configure a standard MAC access list.
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, see Flow-based Monitoring in the “Port Monitoring” section of the Dell EMC Networking OS Configuration Guide. Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History Usage Information This guide is platform-specific.
clear ip prefix-list Reset the number of times traffic mets the conditions (“hit” counters) of the configured prefix lists. Syntax Parameters Defaults clear ip prefix-list [prefix-name] prefix-name (OPTIONAL) Enter the name of the configured prefix list to clear only counters for that prefix list, up to 140 characters long. Clears “hit” counters for all prefix lists unless a prefix list is specified. Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific.
le max-prefix- length Defaults (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32. Not configured. Command Modes PREFIX-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
bitmask number Defaults Enter the keyword bitmask then enter a bit mask number in dotted decimal format. Not configured. Command Modes PREFIX-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
Example Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show ip prefix-list detail Ip Prefix-list with the last deletion/insertion: PL_OSPF_to_RIP ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 seq 5 permit 1.1.1.
Example Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show ip prefix-list summary Ip Prefix-list with the last deletion/insertion: PL_OSPF_to_RIP ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 DellEMC# Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit.
Match clause with Continue clause The continue feature can exist without a match clause. A continue clause without a match clause executes and jumps to the specified route-map entry. With a match clause and a continue clause, the match clause executes first and the continue clause next in a specified route map entry. The continue clause launches only after a successful match.
Related Commands Version Description pre-7.7.1.0 Introduced. ● route-map — enable a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command. Parameters Defaults as-path-name Enter the name of an established AS-PATH ACL, up to 140 characters. Not configured.
match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Syntax match community community-list-name [exact] To delete a community match filter, use the no match community command. Parameters Defaults community-listname Enter the name of a configured community list. exact (OPTIONAL) Enter the keywords exact to process only those routes with this community list name. Not configured.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
Parameters Defaults prefix-list-name Enter the name of configured prefix list, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-6.1.1.0 Introduced on the E-Series. match route-type To match routes based on the how the route is defined, configure a filter.
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address.
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address. ip route-source — redistribute routes that match routes advertised by other routers.
Usage Information Example Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
Usage Information Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. You can prepend up to eight AS numbers to a BGP route. This command influences best path selection in BGP by inserting a tag or AS number into the AS_PATH attribute. ● match as-path — redistribute routes that match an AS-PATH attribute.
● set metric — specify the metric value assigned to redistributed routes. ● set metric-type — specify the metric type assigned to redistributed routes. ● set tag — specify the tag assigned to redistributed routes. set comm-list delete To remove the specified community list from the BGP route’s COMMUNITY attribute, configure a filter. Syntax set comm-list community-list-name delete To insert the community list into the COMMUNITY attribute, use the no set comm-list community-list-name delete command.
Related Commands ● match community — redistribute routes that match the COMMUNITY attribute. ● set community — specify a COMMUNITY attribute. set community Allows you to assign a BGP COMMUNITY attribute. Syntax set community {community-number | local-as | no-advertise | no-export | none} [additive] To delete a BGP COMMUNITY attribute assignment, use the no set community {communitynumber | local-as | no-advertise | no-export | none} command.
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● match community — redistribute routes that match the COMMUNITY attribute. ● show ip bgp community — display BGP community groups. set level To specify the IS-IS level or OSPF area to which matched routes are redistributed, configure a filter.
Related Commands Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● set set set set automatic-tag — compute the tag value of the route. metric — specify the metric value assigned to redistributed routes. metric-type — specify the metric type assigned to redistributed routes. tag — specify the tag assigned to redistributed routes.
Usage Information The set local-preference command changes the LOCAL_PREF attribute for routes meeting the route map criteria. To change the LOCAL_PREF for all routes, use the bgp default localpreference command. Related Commands ● bgp default local-preference — change the default LOCAL_PREF attribute for all routes. set metric To assign a new metric to redistributed routes, configure a filter. Syntax set metric [+ | -] metric-value To delete a setting, enter no set metric.
set metric-type To assign a new route type for routes redistributed to OSPF, configure a filter. Syntax set metric-type {internal | external | type-1 | type-2} To delete a setting, use the no set metric-type command. Parameters Defaults internal Enter the keyword internal to assign the Interior Gateway Protocol metric of the next hop as the route’s BGP MULTI_EXIT_DES (MED) value. external Enter the keyword external to assign the IS-IS external metric.
set next-hop To specify an IP address as the next hop, configure a filter. Syntax set next-hop ip-address To delete the setting, use the no set next-hop ip-address command. Parameters Defaults ip-address Specify an IP address in dotted decimal format. Not configured. Command Modes ROUTE-MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
Defaults igp Enter the keyword igp to set routes originating within the same AS. incomplete Enter the keyword incomplete to set routes with incomplete routing information. Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
Example DellEMC(conf-nprefixl)# show config ! ip prefix-list PL_OSPF_to_RIP seq 5 permit 1.1.1.0/24 seq 10 deny 2.1.0.0/16 ge 23 seq 25 permit 192.0.0.0 bitmask 192.0.0.0 DellEMC(conf-nprefixl)# show route-map Display the current route map configurations. Syntax Parameters show route-map [map-name] map-name (OPTIONAL) Enter the name of a configured route map, up to 140 characters. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
Related Commands ● route-map — configure a route map. AS-Path Commands The following commands configure AS-Path ACLs. ip as-path access-list Enter AS-PATH ACL mode and configure an access control list based on the BGP AS_PATH attribute. Syntax ip as-path access-list as-path-name Parameters Defaults as-path-name Enter the access-list name, up to 140 characters. Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific.
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
Example Version Description pre-Version 6.1.1.0 Introduced on the E-Series. DellEMC(conf)# ip community-list TestComList DellEMC(config-community-list)# show ip community-lists Display configured IP community lists in alphabetic order. Syntax show ip community-lists [name] Parameters name (OPTIONAL) Enter the name of the standard or extended IP community list, up to 140 characters. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
deny ip Disassociate the UDF in IP access-list. Syntax deny ip {source mask | any | host ip-address} {destination mask | any | host ip-address} udf-pkt-format name udf-qualifier-value name To remove this filter, use the no seq sequence-number command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous.
Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. key Configure UDF data context for parsing the different header location offset and required bytes. Syntax key description udf-id id packetbase PacketBase offset bytes length bytes To return to the default settings, use the no key description udf-id id packetbase PacketBase offset bytes length bytes command. Parameters description Enter the key name for reference, up to 64 characters.
Parameters l2ethertype Enter the keyword l2ethertype to match the L2 Ethertype. ipv4 Enter the keyword ipv4 to match the IPv4 packet. ipprotocol value Enter the keyword ipprotocol then the option to match the IPv4 protocol. The options are: ● ● ● ● vlantag tagStatus Enter the keyword vlantag then the option to match the VLAN packet. The options are: ● ● ● ● Defaults IP protocol number. The range is from 0 to 255. icmp — Internet control message protocol. tcp — Transmission control protocol.
CONFIGURATION-EXTENDED-ACCESS-LIST mode Example Command History Dell(config-ext-nacl)#permit ip any any udf-pkt-format ipinip udfqualifier-value ipnip_val1 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON.
Example Command History Dell(conf-udf-tcam-qual-val)#udf-id 1 aa ff This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. udf-qualifier-value — creates a UDF qualifier value. udf-tcam — creates a context for UDF TCAM.
Example Command History Dell(conf)#udf-tcam ipnip seq 1 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. deny (for Standard IP ACLs) To drop packets with a certain IP address, configure a filter.
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes.
● ip access-list extended — create an extended ACL. seq (for Standard IPv4 ACLs) Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ipaddress}} [count [bytes]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To delete a filter, use the no seq sequence-number command.
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Parameters ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
deny arp (for Extended MAC ACLs) Configure an egress filter that drops ARP packets on egress ACL supported line cards. (For more information, refer to your line card documentation). Syntax deny arp {destination-mac-address mac-address-mask | any} vlan vlan-id {ipaddress | any | opcode code-number} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. 9.4(0.
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
deny (for Extended MAC ACLs) To drop packets that match the filter criteria, configure a filter. Syntax deny {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | mac-destination-address mac-destination-addressmask} [ethertype-operator] [count [byte]][log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering theflow-based enable command in the Monitor Session mode.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Parameters ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, standard and extended IPv6 ACLs, and standard and extended MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms.
Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100..
seq (for IPv6 ACLs) Assign a sequence number to a deny or permit the filter in an IPv6 access list while creating the filter. Syntax seq sequence-number {deny | permit} {ipv6-protocol-number | icmp | ip | tcp | udp} {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [operator port [portnumber ]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To delete a filter, use the no seq sequence-number command.
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminate with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [operator port [port]] [ttl operator] [count [byte]] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
● rst: reset the connection ● syn: synchronize sequence numbers ● urg: urgent field operator (OPTIONAL) Enter one of the following logical operand: ● ● ● ● ● port port eq = equal to neq = not equal to gt = greater than lt = less than range = inclusive range of ports (you must specify two ports for the port parameter) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P0) Added the established parameter on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.
Parameters source address mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip- Enter the keyword host then the IPv6 address to specify a host IP address. v6address destination Enter the IP address of the network or host to which the packets are sent.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.
Parameters ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● ● ● ● 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements. Topics: • • • • • • • • • • member vlan ip access-group show acl-vlan-group show cam-acl-vlan cam-acl-vlan show cam-usage show running config acl-vlan-group acl-vlan-group show acl-vlan-group detail description (ACL VLAN Group) member vlan Add VLAN members to an ACL VLAN group.
Attaching an ACL individually to VLAN interfaces is similar to the behavior of ACL-VLAN mapping storage in CAM prior to the implementation of the ACL VLAN group functionality. ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax ip access-group {group name} out implicit-permit Parameters Default group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
Version Description 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage. During the initialization of CAM, the chassis manager reads the NVRAM and allocates the dynamic VCAP regions.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S4810 and Z9000 platforms.
Example 1: Output of the show cam-usage Command 332 Field Description CAM Partition Type of area in the CAM block that is used for ACL VLAN groups Total CAM Total amount of space in the CAM block Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs DellEMC#show cam-usage Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM | Available CAM ========|========|=================|=============|=============| ===
Example 2: Output of the show cam-usage acl Command Example 3: Output of the show cam-usage router Command DellEMC#show cam-usage acl Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM | Available CAM ========|========|=================|=============|=============| ============== 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | IN-L3 ACL | 1024 | 1 | 1023 | | IN-V6 ACL | 0 | 0 | 0 | | OUT-L2 ACL | 206 | 9 | 197 | | OUT-L3 ACL | 178 | 9 | 169 | | OUT-V6 ACL | 178 | 4 | 174 2 | 0 | IN-L2 ACL | 1536 | 0 | 1536
| IN-L3 ACL | 1024 | 1 | IN-V6 ACL | 0 | 0 | OUT-L3 ACL | 178 | 9 | | | OUT-V6 ACL | 174 Codes: * - cam usage is above 90%.
DellEMC#show running-config acl-vlan-group ! acl-vlan-group Test member vlan 1-100 ip access-group test in DellEMC# Test acl-vlan-group Create an ACL VLAN group. Syntax acl-vlan-group {group name} To remove an ACL VLAN group, use the no acl-vlan-group {group name} command. Parameters Default group-name Specify the name of the ACL VLAN group. The name can contain a maximum 140 characters.
Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information The output for this command displays in a line-by-line format.
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
which a neighbor belongs. The neighbors inherit only the global timer values (configured with the bfd neighbor command). You can only enable BFD for VRRP in INTERFACE command mode (vrrp bfd all-neighbors). You can enable BFD on both default and nondefault VRFs for OSPF and BGP protocols for both IPv4 and IPv6 neighbors. NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd enable (Configuration) Enable BFD on all interfaces.
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC(conf-if-te-1/3)# bfd interval 250 min_rx 300 multiplier 4 role passive DellEMC(conf-if-te-1/3)# bfd protocol-liveness Enable the BFD protocol liveness feature.
To disable BFD for all neighbors configured through static routes, use the no ip route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command. Parameters prefix-list prefix- (Optional) Enter the keyword prefix-list followed by the name of the prefix list-name list to enable or disable BFD on specific neighbors.
ip ospf bfd all-neighbors Establish BFD sessions with all OSPF neighbors on a single interface or use non-default BFD session parameters. Syntax ip ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPF interface implicitly, use the no ip ospf bfd allneighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters. Syntax ipv6 ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPFv3 interface implicitly, use the no ipv6 ospf bfd allneighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
ipv6 route bfd Enable BFD for all IPv6 neighbors configured through static routes. Syntax ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] To disable BFD for all IPv6 neighbors configured through static routes, use the no ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command.
To remove all BFD sessions with IS-IS neighbors discovered on this interface, use the no isis bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] command. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface. interval (OPTIONAL) Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200.
Parameters ip-address Enter the IP address of the BGP neighbor that you want to explicitly disable for BFD sessions in dotted decimal format (A.B.C.D). peer-group-name Enter the name of the peer group that you want to explicitly disable for BFD sessions. Defaults None Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
V VT - VRRP - Vxlan Tunnel LocalAddr * 5.1.1.1 * 6.1.1.1 * 7.1.1.1 RemoteAddr 5.1.1.2 6.1.1.2 7.1.1.2 Interface Po 30 Vl 30 Te 1/21 State Up Up Up Rx-int 200 200 200 Tx-int 200 200 200 Mult 3 3 3 Clients O O O The following example shows the show bfd vrf neighbors command output showing the nondefault VRF.
Local Addr: 6.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 6.1.1.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
Defaults Disabled Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
router bgp 1 bgp four-octet-as-support bgp asnotation asdot DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands ● bgp four-octet-as-support — enable
Usage Information If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipathrelax command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
Usage Information Version Description 6.3.1.0 Introduced The MED is a 4-byte unsigned integer value and the default behavior is to assume a missing MED as 4294967295. This command causes a missing MED to be treated as 0. During path selection, paths with a lower MED are preferred over paths with a higher MED. bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command.
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added support for the 4-byte format To accept 4-byte formats before entering a 4-byte AS number, configure your system. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added support for the 4-byte format. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors.
reuse (OPTIONAL) Enter a number as the reuse value, which is compared to the flapping route’s Penalty value. If the Penalty value is less than the reuse value, the flapping route is once again advertised (or no longer suppressed). The range is from 1 to 20000. The default is 750. suppress (OPTIONAL) Enter a number as the suppress value, which is compared to the flapping route’s Penalty value.
To return to the default value, use the no bgp default local-preference command. Parameters Defaults value Enter a number to assign to routes as the degree of preference for those routes. When routes are compared, the higher the degree of preference or local preference value, the more the route is preferred. The range is from 0 to 4294967295. The default is 100. 100 Command Modes ROUTER BGP Command History This guide is platform-specific.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. 9.2(1.0) Introduced on the Z9500. Configuring or un-configuring the command brings down and brings up the BGP Route Manager, this results in tear down and re-establishment of all active sessions.
If you disable the enforce-first-as command, it can be viewed using the show ip protocols command. In the event of an enfore-first-as check failure, the existing BGP session is flapped. Related Commands ● show ip bgp neighbors — view the information the BGP neighbors exchange. ● show ip protocols — view information on routing protocols. bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails.
To disable fast external failover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive.
To disable next-hop resolution, use the no bgp recursive-bgp-next-hop command. Defaults Enabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Usage Information Version Description 9.14(0.1) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6010–ON, and Z9100– ON. After configuring the bgp redistribute-internal command, use the clear ip bgp * command to clear all BGP sessions. If you don’t clear all BGP sessions, route redistribution happens only for new routes. NOTE: When you enable redistribution of iBGP routes into an IGP, ensure that you use route maps to control what prefixes are redistributed.
Usage Information Version Description 7.6.1.0 Introduced BGP uses regular expressions (regex) to filter route information. In particular, the use of regular expressions to filter routes based on AS-PATHs and communities is common. In a large-scale configuration, filtering millions of routes based on regular expressions can be quite CPU intensive, as a regular expression evaluation involves generation and evaluation of complex finite state machines.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router.
flap-statistics Enter the keywords flap-statistics to clear the flap statistics information. ipv4 Enter the ipv4 address family to clear. ipv6 Enter the ipv6 address family to clear. peer-group Enter the peer-group to clear all members of the peer-group. Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to clear the ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to clear the ipv6 unicast routes. ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to clear dampening information only that BGP neighbor.
NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF. You can also use this attribute to return the suppressed routes corresponding to a specific VRF to an active state. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to clear information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to clear information related only to ipv4 unicast routes.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information If you enter the clear ip bgp flap-statistics command without any parameters, all statistics are cleared. Related Commands ● show debugging — view the enabled debugging operations. ● show ip bgp flap-statistics — view the BGP flap statistics. ● undebug all — disable all debugging operations.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
To disable all BGP debugging, use the no debug ip bgp command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to debug BGP information corresponding to that VRF. NOTE: Use this attribute to debug BGP protocol operations corresponding to either a default or non-default VRF. A.B.C.D Enter the IPv4 address of the neighbor in dotted decimal format. X:X:X:X::X (OPTIONAL) Enter an IPv6 address.
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To view information on both incoming and outgoing routes, do not include the in and out parameters in the debugging command. The in and out parameters cancel each other; for example, if you enter the debug ip bgp in command and then enter the debug ip bgp out command, you do not see information on the incoming routes.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced IPv6 MGBP support for the E-Series. debug ip bgp events Display information on local BGP state changes and other BGP events. Syntax debug ip bgp [vrf vrf-name] [A.B.C.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp keepalives Display information about BGP keepalive messages. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] keepalives [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] notifications [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.
debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group-name] softreconfiguration To disable, use the debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peergroup-name] soft-reconfiguration command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable soft-reconfiguration debugging on that VRF. A.B.C.
debug ip bgp updates Allows you to view information about BGP updates. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] updates [in | out | prefix-list prefix-list-name] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] updates [in | out | prefix-list prefix-listname] command.
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. default-metric Allows you to change the metric of redistributed routes to locally originated routes. Use this command with the redistribute command. Syntax default-metric number To return to the default setting, use the no default-metric command. Parameters Defaults number Enter a number as the metric to be assigned to routes from other protocols. The range is from 1 to 4294967295.
To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the BGP protocol (80 characters maximum). none Command Modes ROUTER BGP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group. Defaults send Enter the keyword send to indicate that the system sends multiple paths to peers. receive Enter the keyword receive to indicate that the system accepts multiple paths from peers. both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported.
Defaults ● seconds = 5 seconds (internal peers) ● seconds = 30 seconds (external peers) Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path.
Version Description 7.7.1.0 Introduced on the C-Series. Usage Information You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process. neighbor default-originate Inject the default route to a BGP peer or neighbor.
When you configure a route-map for a BGP peer or peer group with the neighbor defaultoriginate command, the command checks for the existence of the route in BGP RIB. Route-map configuration on a BGP peer or peer group works only when the LOC-RIB contains at least one route. When you apply a default route to a BGP peer or peer group using the neighbor defaultoriginate command, changes to the configured default route-map are applied to the BGP peer or peer group only after a delay of 15 seconds.
Version Description 7.7.1.0 Introduced on the C-Series. neighbor distribute-list Distribute BGP information via an established prefix list. Syntax neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
neighbor ebgp-multihop Attempt and accept BGP connections to external peers on networks that are not directly connected. Syntax neighbor {ip-address | peer-group-name} ebgp-multihop [ttl] To disallow and disconnect connections, use the no neighbor {ip-address | peer-groupname} ebgp-multihop command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group.
Defaults Disabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
Command History Usage Information Version Description 9.10(0.0) Introduced the all keyword on the S4810, S4820, S4048–ON, S3048–ON, S3100 series, S6010–ON, S4040T-ON, S5000, S6000, S6000–ON, S6100–ON, Z9100– ON, and Z9500. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. This command automatically restarts the neighbor session for the configuration to take effect. Configure the same password on both BGP peers or a connection does not occur.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the dmzlink-bw parameter. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced the limit keyword on the S4810. 8.3.7.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Applies to EBGP neighbors only. Configure your system to accept 4-byte formats before entering a 4 byte AS Number.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector, the internal BGP (IBGP) speakers in the network must be fully meshed.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To configure a COMMUNITY attribute, use the set community command in ROUTE-MAP mode.
NOTE: If you configure a neighbor to accept such routes using the neighbor allowas-in command, you must disable sender-side loop detection for that neighbor. Related Commands ● bgp client-to-client reflection — enable route reflection between the route reflector and the clients. neighbor shutdown Disable a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} shutdown To enable a disabled neighbor or peer group, use the neighbor {ip-address | peer-groupname}no shutdown command.
neighbor soft-reconfiguration inbound Enable soft-reconfiguration for BGP. Syntax neighbor {ip-address | peer-group-name} soft-reconfiguration inbound To disable, use the no neighbor {ip-address | peer-group-name} softreconfiguration inbound command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to disable or enable all routers within the peer group.
neighbor timers Set keepalive and hold time timers for a BGP neighbor or a peer group. Syntax neighbor {ip-address | peer-group-name} timers keepalive holdtime To return to the default values, use the no neighbor {ip-address | peer-group-name} timers command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to set the timers for all routers within the peer group.
neighbor timers extended Set idle hold time for a BGP neighbor or a peer group. Syntax neighbor {ip-address | ipv6-address | peer-group-name} timers extended idle holdtime To return to the default values, use the no neighbor {ip-address | ipv6-address | peergroup-name} timers extended idle holdtime command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. ipv6-address Enter the IPv6 address of the peer router in X:X:X:X::X format.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In the Dell EMC Networking OS best path selection process, the path with the highest weight value is preferred.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. ● deny bandwidth – link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. redistribute Redistribute routes into BGP. Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. At least one interface must be in Layer 3 mode for the router bgp command to be accepted.
Usage Information You can use this command to disable all the configured BGP neighbors corresponding to the multicast IPv4 address families. This command is global for all VRFs. shutdown address-family-ipv4–unicast Disables all the BGP neighbors corresponding to the unicast IPv4 address families. Syntax shutdown address-family-ipv4–unicast Use the no shutdown address-family-ipv4–unicast command to enable all the configured BGP neighbors corresponding to the unicast IPv4 address families.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced. Example DellEMC(conf-router_bgp)# show capture bgp-pdu neighbor 20.20.20.2 Incoming packet capture enabled for BGP neighbor 20.20.20.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Example DellEMC(conf-router_bgp)# show config ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC(conf-router_bgp)# show ip bgp View the current BGP IPv4 routing table for the system.
dampened-paths (OPTIONAL) Enter the keyword dampened-paths to display the paths suppressed due to dampening. extcommunitylist list name (OPTIONAL) Enter the keyword extcommunity-list then the list name to display the routes matching the extended community-list. filter-list aspath-name (OPTIONAL) Enter the keyword filter-list then the as-path-name to display the routes conforming to the filter–list. flap–statistics (OPTIONAL) Enter the keyword flap-statistics to display flap statistics of the routes.
Usage Information Version Description 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. In BGP, this command displays the exact reason why the route is discarded.
BGP local router ID is 1.1.1.1 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete ID *>I ID *>I ID *>I ID ID ID ID ID Network 110.1.1.0/24 111.1.1.0/24 112.1.1.0/24 113.1.1.0/24 114.1.1.0/24 115.1.1.0/24 116.1.1.0/24 117.1.1.0/24 118.1.1.0/24 119.1.1.0/24 120.1.1.0/24 Next Hop 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.
● show ip bgp next-hop — view all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. ● show ip bgp paths — view all the BGP path attributes in the BGP database. ● show ip bgp peer-group — allow you to view information on the BGP peers in a peer group. ● show ip bgp regexp — display the subset of the BGP routing tables matching the regular expressions specified.
Usage Information Example Version Description 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned.
You can specify up to eight community numbers to view information on those community groups. local-AS Enter the keywords local-AS to view all routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED. All routes with the NO_EXPORT_SUBCONFED (0xFFFFFF03) community attribute must not be advertised to external BGP peers. no-advertise Enter the keywords no-advertise to view all routes containing the well-known community attribute of NO_ADVERTISE.
Example Field Description Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
AS_PATH : 200 Next-Hop : 172.16.0.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref Communities : 200:1 1000:1 DellEMC# 100, Weight 0, external 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active).
Usage Information To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized. The history paths that the show ip bgp command displays contain only the prefix and the next-hop information.
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
show ip bgp extcommunity-list View information on all routes with Extended Community attributes. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] extcommunity-list [list name] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information on all routes with extended community attributes corresponding to that VRF.
Example DellEMC# show run extcommunity-list ! ip extcommunity-list ecl1 permit rt 100:4 permit soo 40:4 DellEMC#show ip bgp extcommunity-list ecl1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp filter-list hello command shown in the following example.
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
Usage Information Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp flap command shown in the following example. Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route. Flaps Displays the number of times the route flapped. Duration Displays the hours:minutes:seconds since the route first flapped.
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
I 32.32.32.32/32 60.0.0.2 I 32.32.33.33/32 60.0.0.2 *>n 33.33.33.33/32 0.0.0.0 *>n 33.33.44.55/32 0.0.0.0 *>n 44.44.44.44/32 0.0.0.0 *>I 55.55.0.0/16 72.1.1.2 *>I 55.55.55.55/32 72.1.1.2 *>I 55.55.66.66/32 72.1.1.2 *>a 66.66.0.0/16 0.0.0.0 *>n 66.66.66.77/32 0.0.0.0 *>n 66.66.77.77/32 0.0.0.0 DellEMC# 0 0 0 0 0 0 0 100 100 100 100 100 0 400 500 i 0 400 500 i 32768 i 32768 i 32768 i 0 i 0 i 0 i 32768 i 32768 i 32768 i show ip bgp neighbors Allows you to view the information BGP neighbors exchange.
● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced the [all] option for IPv4 and IPv6 neighbors. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.
The Lines Beginning with: Description ● last read is the time (hours:minutes:seconds) the router read a message from its neighbor ● hold time is the number of seconds configured between messages from its neighbor ● keepalive interval is the number of seconds between keepalive messages to help ensure that the TCP session is still alive.
Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop.
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Syntax show ip bgp [vrf vrf-name] paths community Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf to view information on BGP peers in a peer group corresponding to that VRF. NOTE: You can use this attribute to view information on BGP peers in a peer group that correspond to either a default or a non-default VRF.
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp peer-group command shown in the following example. Line beginning Description with: Example Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported.
● ● ● ● . * + ? = = = = (period) any single character (including a white space). (asterisk) the sequences in a pattern (zero or more sequences). (plus) the sequences in a pattern (one or more sequences). (question mark) sequences in a pattern (either zero or one sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element.
Example DellEMC# show ip bgp regexp ^200 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 55.0.0.0/24 *> 66.0.0.0/24 DellEMC# Next Hop 172.16.0.2 172.16.0.
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes. For example, if cluster_id is an attribute associated with thousand routes that contain exactly the same set of attributes, then the cluster_id count is 1.
Field State/Pfxrcd Description Time Established Display Example < 1 day 00:12:23 (hours:minutes:seconds) < 1 week 1d21h (DaysHours) > 1 week 11w2d (WeeksDays) If the neighbor is in Established stage, the number of network prefixes received. If a maximum limit was configured with the neighbor maximum-prefix command, (prfxd) appears in this column. If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm).
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. DellEMC# show running-config bgp ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC# timers bgp Adjust the BGP Keep Alive and Hold Time timers.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. timers bgp extended Adjust the BGP idle holdtime for all the BGP neighbors. Syntax timers bgp extended idle-holdtime To return to the default, use the no timers bgp extended command.
debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
To return to default values, use the no distance bgp command. Parameters external-distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internal-distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200. local-distance Defaults Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255.
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Network d From 55.0.0.0/24 172.16.0.2 Reuse Path 00:36:23 200 DellEMC# BGP Extended Communities (RFC 4360) BGP Extended Communities, as defined in RFC 4360, is an optional transitive BGP attribute. BGP Extended Communities provides two major advantages over Standard Communities: ● The range is extended from 4-octet (AA:NN) to 8-octet (Type:Value) to provide enough number communities.
Usage Information Related Commands Version Description 7.6.1.0 Introduced on the E-Series. If the set community rt and soo are in the same route-map entry, the behavior defines as: ● If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. ● If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. ● If the rt with the additive option comes after soo, rt adds the communities soo sets.
● If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. ● If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. ● If the rt with the additive option comes after soo, rt adds the communities soo sets. Related Commands ● set extcommunity rt — set the extended community route origins using the route-map.
show ip extcommunity-list Display the IP extended community list. Syntax show ip extcommunity-list [word] Parameters word Enter the name of the extended community list you want to view. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
as-number Clear and reapply policies for all neighbors belonging to the AS. The range is from 0 to 65535 (2 Byte), from 1 to 4294967295 (4 Byte), or from 0.1 to 0.65535.65535 (Dotted format). ipv4-neighboraddr | ipv6neighbor-addr Clear and reapply policies for a neighbor. peer-group name Clear and reapply policies for all BGP routers in the specified peer group. ipv6 unicast Clear and reapply policies for all IPv6 unicast routes. in Reapply only inbound policies.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Added support for IPv4 multicast and IPv6 unicast routes. 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced on the E-Series. This command turns on BGP soft-reconfiguration inbound debugging for IPv6 unicast routes. If no neighbor is specified, debug is turned on for all neighbors.
Command Modes ROUTER BGPv6 ADDRESS FAMILY (conf-router_bgpv6_af) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.4.1.0 Added support for IPv4 multicast and IPv4 unicast address families. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Introduced on the S4810. 7.7.1.
IPv6 MBGP Commands Multiprotocol BGP (MBGP) is an enhanced BGP that enables the multicast routing policy throughout the internet and connecting multicast topologies between BGP and autonomous systems (AS). FTOS MBGP is implemented as per IETF RFC 1858. show ipv6 mbgproutes Display the selected IPv6 MBGP route or a summary of all MBGP routes in the table.
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● IPV4Acl : 4 IPV6Acl : 0 IPV4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 nlbclusteracl: 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 ipv4udfmirracl: 0 vrfv4Acl :0 Openflow : 0 fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 8.
Openflow number Enter the keyword openflow and then the number of FP blocks for open flow (multiples of 4). The range is from 0 to 8. fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The range is from 0 to 6. Iscsioptacl Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2. number ipv4udfmirracl Enter the keyword ipv4udfmirracl and then the number of FP blocks for IPv4 UDF mirror ACL.
Usage Information Save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings to take effect. The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only number of blocks can be configured by the user . If allocation values are not entered for the CAM regions, the value is 0.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Supported Modes Command History Usage Information Example Version Description 9.14.1.0 Introduced on the S4810 and S4820T. 9.13.0.0 Introduced on the MXL, FN IOM, S5000, S4048-ON, S6000, S6000-ON, S3048ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. The no cam-threshold command will set the CAM threshold to 90 percent and silence period to 0.
Example DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p
IPV6(IPV4QOS) Triple Wide Regions: VmanQos, Openflow, ipv4udfmirracl L2Acl : 2 Ipv4Acl : 4 Ipv6Acl* : 2 Ipv4Qos* : 0 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl: 0 ipv4mirracl : 0 * - shared regions show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow) Syntax show cam-usage [acl | rout
Table 3.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Unified Forwarding Table Modes Unified Forwarding Table (UFT) consolidates the resources of several search tables (Layer 2, Layer 3 Hosts, and Layer 3 Route [Longest Prefix Match — LPM]) into a single flexible resource. The system supports several UFT modes to extract the forwarding tables, as required. By default, Dell EMC Networking OS initializes the table sizes to UFT mode 2 profile, as it provides a reasonable shared memory for all the tables.
The following is a list of the Dell EMC Networking OS version history for this command. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax service-policy rate-limit-cpu-queues policy-name Parameters Defaults policy-name Enter the service-policy name, using a string up to 32 characters. Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History Usage Information This guide is platform-specific.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
LLDP GVRP STP ISIS DellEMC# 490 any 01:80:c2:00:00:21 01:80:c2:00:00:00 01:80:c2:00:00:14/15 09:00:2b:00:00:04/05 Control Plane Policing (CoPP) 0x88cc any any any any Q8 Q8 Q7 Q9 Q9 CP CP CP CP CP _ _ _ _
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release.
● The maximum number of lossless queues globally supported on the switch is two. The following lists the dot1p priority-queue assignments. dot1p Value in Description heading the Incoming Frame 0 1 1 0 2 2 3 3 4 4 5 5 6 6 7 7 ● Before configuring the port queues to function as no-drop queues, you must first apply the dcb-map map with pfc mode off. To apply the dcb-map with pfc mode off, use the following commands: dcbmap pfcoff and no pfc mode on.
show interface pfc Displays the PFC configuration applied to ingress traffic on an interface, including priorities and link delay. Syntax show interface port-type slot/port[/subport] pfc {summary | statistics | detail | buffer-threshold} Parameters port-type slot/ port[ /subport ] pfc Enter the port-type slot and port PFC information. Enter the subport number if a port is fanned-out into 10G ports.
Field Description from peers; received PFC configuration take effect. The admin operational status for a DCBX exchange of PFC configuration is enabled or disabled. Remote is enabled, Priority list Remote Willing Status is enabled Operational status (enabled or disabled) of peer device for DCBX exchange of PFC configuration with a list of the configured PFC priorities. Willing status of peer device for DCBX exchange (Willing bit received in PFC TLV): enabled or disable.
Example (Summary) Field Description PFC TLV Statistics: Error pkts Number of PFC error packets received. PFC TLV Statistics: Pause Tx pkts Number of PFC pause frames transmitted. PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
port-number Enter the port number. Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default, equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure bandwidth amounts in associated dot1p queues, use the bandwidth-percentage command.
dcb-enable Enable data center bridging. Syntax dcb enable[pfc-queues 1–4] To disable DCB, use the no dcb enable command. Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. priority-list Configure the 802.1p priorities for the traffic on which you want to apply an ETS output policy. Syntax priority-list value To remove the priority list, use the no priority-list command. Parameters Defaults value Enter the priority list value.
Usage Information If an error occurs in an ETS output-policy configuration, the configuration is ignored and the scheduler and bandwidth allocation settings are reset to the ETS default values (all priorities are in the same ETS priority group and bandwidth is allocated equally to each priority). If an error occurs when a port receives a peer’s ETS configuration, the port’s configuration is reset to the previously configured ETS output policy.
show interface ets Displays the ETS configuration applied to egress traffic on an interface, including priority groups with priorities and bandwidth allocation. Syntax Parameters show interface port-type slot/port[/subport] ets {summary | detail} port-type slot/ port[/subport] ets Enter the port-type slot and port ETS information. Enter the subport number if a port is fanned-out into 10G ports.
0 1 2 3 4 5 6 7 0,1,2 3 4,5,6,7 100% 0 % 0 % - ETS SP SP - Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf T
3 4 5 6 7 4,5,6,7 0 % - SP - Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts DellEMC# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----
Class Pkts Example (Detail) DellEMC(conf)# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled
show qos priority-groups Displays the ETS priority groups configured on the switch, including the 802.1p priority classes and ID of each group. Syntax show qos priority-groups Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
1 2 3 4 5 6 7 8 - - Stack unit 2 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 - DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements.
advertise dcbx-appln-tlv On a DCBX port with a manual role, configure the application priority TLVs advertised on the interface to DCBX peers. Syntax advertise dcbx-appln-tlv {fcoe | iscsi} To remove the application priority TLVs, use the no advertise dcbx-appln-tlv {fcoe | iscsi} command. Parameters {fcoe | iscsi} Enter the application priority TLVs, where: ● fcoe: enables the advertisement of FCoE in application priority TLVs. ● iscsi: enables the advertisement of iSCSI in application priority TLVs.
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. You can configure the transmission of more than one TLV type at a time; for example: advertise dcbx-tlv ets-conf ets-reco.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command.
debug dcbx Enable DCBX debugging. Syntax debug dcbx {all | auto-detect-timer | config-exchng | fail | mgmt | resource | sem | tlv} To disable DCBX debugging, use the no debug dcbx command. Parameters Defaults {all | autodetect-timer | config-exchng | fail | mgmt | resource | sem | tlv} Enter the type of debugging, where: ● ● ● ● ● ● ● ● all: enables all DCBX debugging operations. auto-detect-timer: enables traces for DCBX auto-detect timers.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. This command is available at the global level only.
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
Field Description Local DCBX TLVs Transmission status (enabled or disabled) of advertised DCB TLVs (see TLV code Transmitted at the top of the show command output). Local DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs. Local DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs. Local DCBX Sequence number transmitted in Control TLVs. Status: Sequence Number Local DCBX Acknowledgement number transmitted in Control TLVs.
F-Application priority for FCOE enabled f-Application Priority for FCOE disabled I-Application priority for iSCSI enabled i-Application Priority for iSCSI disabled ----------------------------------------------------------Interface TenGigabitEthernet 1/9 Remote Mac Address 00:00:00:00:00:11 Port Role is Auto-Upstream DCBX Operational Status is Enabled Is Configuration Source? TRUE Local DCBX Compatibility mode is CEE Local DCBX Configured mode is CEE Peer Operating version is CEE Local DCBX TLVs Transmitted
Usage Information A DCB map is a template used to configure DCB parameters and apply them on converged Ethernet interfaces. DCB parameters include priority-based flow control (PFC) and enhanced traffic selection (ETS). To display the PFC and ETS settings in DCB maps, enter the show qos dcb-map name command. Use the dcb-map command to create a DCB map to specify PFC and ETS settings and apply it on Ethernet ports.
For PFC enabled priorities, it is recommended to map single priority per Priority group. pfc mode on Enable the PFC configuration on the port so that the priorities are included in DCBX negotiation with peer PFC devices. Syntax pfc mode on To disable the PFC configuration, use the no pfc mode on command. Defaults PFC mode is on. Command Modes DCB MAP Command History Usage Information This guide is platform-specific.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.
Usage Information Version Description 9.3(0.0) Introduced on the S4810 and S6000 platforms. The dcb-map stack-unit all stack-ports all command overwrites any previous DCB maps applied to stack ports. show qos dcb-map Display the DCB parameters configured in a specified DCB map. Syntax show qos dcb-map map-name Parameters map-name Displays the PFC and ETS parameters configured in the specified map.
PG:1 TSA:ETS Priorities:3 BW:50 PFC:ON dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. Syntax Parameters Default dcb pfc-shared—buffer—size buffer-size buffer-size Enter a number in the range of 0 to 7787. The default is 832KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.0) Introduced on the S5000. 9.3(0.0) Introduced on the S4810, S4820T, and S6000.
threshold-value Buffer offset limit at which the port resumes the peer in KB. Enter a number in the range of 1 to 7787. The default is 10 KB. sharedBuffer shared threshold weight threshold-weight size Weightage of the priorities on the shared buffer size in the system. Enter a number in the range of 0 to 9. The default shared threshold weight is 10. Command Modes DCB-BUFFER-THRESHOLD mode Command History Usage Information This guide is platform-specific.
queue 0 to queue Specify the queue number to which the QoS policy buffer parameters apply 7 pause Pause frames to be sent at the specified buffer limit levels and pause packet settings no-drop The packets for this queue must not be dropped value Enter a number in the range of 0 to 7 to denote the priority to be allocated to the dynamic buffer control mechanism buffer-size Ingress buffer size size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 45 KB.
dcb-policy buffer-threshold (Interface Configuration) Assign the DCB policy to the DCB buffer threshold profile on interfaces. This setting takes precedence over the global bufferthreshold setting. Syntax Parameters Default dcb-policy buffer-threshold profile-name buffer-threshold Configure the profile name for the DCB buffer threshold profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
Version Description 9.9(0.0) Introduced on the S6000 and the S6000–ON. 9.8(0.0) Introduced on the S4048-ON. 9.6(0.0) Introduced on the S5000. 9.3(0.0) Introduced on the S4810 and S4820T platforms. Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process.
dcb pfc-total-buffer-size Configure the total buffer size for PFC in kilobytes. Syntax Parameters Default dcb pfc-total—buffer—size buffer-size buffer-size Enter a number in the range of 0 to 7787. The default is 6592KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration. Syntax show running—config dcb-buffer-threshold Command Modes EXEC EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
7 - No Denotes dynamic buffering is enabled in respective queues - On interface in which PFC is not enabled: DellEMC#show interface tengigabitethernet 1/20 pfc buffer-threshold The following table describes the output fields displayed for the show interface pfc bufferthreshold command: Field Description queue Number of the queue lossless Whether the queue is a lossy or lossless queue for which buffer threshold is configured buffer-size Ingress buffer size pause-threshold- Buffer limit at which t
Usage Information Example You can configure all the data queues. You can configure queues 0-7. The following table describes the mapping between the threshold weight of the shared buffer on the queue. It also shows the percentage of the available shared buffer used by the queues for each of the corresponding threshold weights of the shared buffer: sharedthresholdweight on the queue % of available shared buffer that can be consumed by the queue 0 No dynamic sharing; shared buffer = 0. 1 0.77% 2 1.
space to be allocated for each priority and the pause or resume thresholds for the buffer. This method of configuration enables you to effectively manage and administer the behavior of lossless queues. Example DellEMC(conf)# dcb pfc-queues 4 dcb {ets | pfc} enable Enable priority flow control or enhanced transmission selection on interface. Syntax dcb {ets | pfc} enable ● To disable ETS on interface, use “no dcb ets enable” command. ● To disable PFC on interface, use “no dcb pfc enable” command.
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
not reachable, the application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
no-reboot Defaults Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit stack-unit-number command. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process.
Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
Related Commands Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. ● show hardware stack-unit — display the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
show hardware mac Display MAC ACL entries for the specified stack-unit, port-pipe and pipeline ID. Syntax Parameters Defaults show hardware mac {eg-acl | in-acl} stack-unit id port-set 0–0 eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack- unit id Enter the keyword stack-unit to select the stack unit ID.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Defaults drops [unit unitnumber ] Enter the keyword drops to display internal drops on the selected stack member. Enter the optional keyword unit unit-number to display the internal drop counters of the specified port pipe. fpga register Enter the keyword to display the register value of the fpga register.
0 Multicasts, 3 Broadcasts, 322 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec Output 00.
0x0060a04c ASFPORTSPEED.ge10 = 0x00000000 0x0060b04c ASFPORTSPEED.ge11 = 0x00000000 0x0060c04c ASFPORTSPEED.ge12 = 0x00000000 0x0060d04c ASFPORTSPEED.ge13 = 0x00000000 0x0060e04c ASFPORTSPEED.ge14 = 0x00000000 0x0060f04c ASFPORTSPEED.ge15 = 0x00000000 0x0061004c ASFPORTSPEED.ge16 = 0x00000000 0x0061104c ASFPORTSPEED.ge17 = 0x00000000 0x0061204c ASFPORTSPEED.ge18 = 0x00000000 0x0061304c ASFPORTSPEED.ge19 = 0x00000000 0x0061404c ASFPORTSPEED.ge20 = 0x00000000 0x0061504c ASFPORTSPEED.
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 546 - Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byt
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter 8 Debug Counter 9 Debug Counter 10 Debug Counter 11 3 4 5 6 7 --------------------unit: 0 port: 61 (interface Fo 1/60) Description RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX
RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - Debug Counter 6 Debug Counter 7 Debug Counter 8 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Fra
****************************************************** Link Status of all the ports in the Device - 1 The linkStatus of Front End Port 0 is FALSE The linkStatus of Front End Port 1 is FALSE The linkStatus of Front End Port 2 is FALSE The linkStatus of Front End Port 3 is FALSE The linkStatus of Front End Port 4 is FALSE The linkStatus of Front End Port 5 is FALSE The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus
Related Commands ● clear hardware system-flow — clear the statistics from selected hardware components. ● show interfaces stack-unit — display information on all interfaces on a specific S-Series stack member. ● show processes cpu (S-Series) — display the CPU usage information based on the processes running in an S-Series. ● show system — display the current status of all the stack members or a specific member.
2036 VRRP STUB 2035 L2_DST_HIT+BC MAC+VLAN 4095 2034 L2_DST_HIT+BC MAC 2033 Catch all 384 OSPF[224.0.0.5] Packets 383 OSPF[224.0.0.
show hardware vlan-counters Display the hardware VLAN statistics. Syntax show hardware vlan-counters vlan-id Parameters Defaults vlan-id Enter the interface VLAN number. The range is from 1 to 4094. None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
RX - Debug Counter 2
Example displaying internal drops Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
show hardware stack-unit buffer-stats-snapshot (Total Buffer Information) View the buffer statistics tracking resource information depending on the type of buffer information, such as device-level details, port-level counters, queue-based snapshots, or priority group-level snapshot in the egress and ingress direction of traffic.
-------------------------------------------------PG# PRIORITIES SHARED CELLS HEADROOM CELLS -------------------------------------------------7 0-2,5 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 0/0 priority-group 7 Unit 0 unit: 0 port: 1 (interface Fo 0/0) -------------------------------------------------PG# PRIORITIES SHARED CELLS HEADROOM CELLS -------------------------------------------------0 0 0 1 0 0 2 0 0 3 7 0 0 4 6 0 0 5 4 0 0 6 3 0 0 7 0-2,5 0 0 show hardware buff
Example displaying priority-group range DellEMC# show hardware buffer interface tengigabitethernet 1/1 prioritygroup 0 buffer-info ----- Buffer stats for unit: 0 port: 1 (interface Te 1/1) ---------------------------------------------------------------------------PG# PRIORITIES ALLOTED (CELLS) COUNTER (CELLS) MIN SHARED MODE HDRM MIN SHARED HDRM -----------------------------------------------------------------------0 61440 0 STATIC 174 0 0 0 DellEMC# Example displaying queue range show hardware buffer-st
Usage Information Example displaying egress queue-level snapshot for both unicast and multicast packets for the specific interface Example displaying egress queue-level snapshot for unicast packets for the specific interface Version Description 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, Z9000, Z9500. -Queue ucast/mcast — Displays the total unicast/multicast buffer usage on per-port per-queue basis.
multicast packets for the specific interface --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 queue mcast all Unit 1 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 0 0 MCAST 1 0 MCAST 2 0 MCAST 3 0 MCAST 4 0 MCAST 5 0 MCAST 6 0 MCAST 7 0 MCAST 8 0 Example dis
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP.
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific.
Parameters Defaults address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. excluded-address Prevent the server from leasing an address or range of addresses in the pool.
hardware-address For manual configurations, specify the client hardware address. Syntax Parameters Defaults hardware-address address address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Usage Information When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.3 or later, the system converts the DHCP CONFIGURATION host command in the running configuration to the hostaddress command. If you downgrade the Dell EMC Networking OS from version 9.14.1.3 or later to an earlier version, any existing host-address command is deleted from the running configuration. If you want to create manual DHCP bindings, use the host command. ip dhcp server Enable DHCP server globally.
Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell EMC Networking recommends specifying clients as hybrid.
network Specify the range of addresses in an address pool. Syntax Parameters Defaults network network /prefix-length network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
show ip dhcp configuration Display the DHCP configuration. Syntax Parameters Defaults show ip dhcp configuration [global | pool name] pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
show ip dhcp conflict Display the address conflict log. Syntax show ip dhcp conflict address Parameters Defaults address Display a particular conflict log entry. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms.
Related Commands ● arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table. arp inspection-limit Configure dynamic ARP inspection rate-limit to verify the rate of ARP packet received in a port on a specific interval. Syntax arp inspection-limit {rate pps [interval seconds]} Defaults None Command Modes INTERFACE CONFIGURATION Parameters Command History rate pps Enter the keyword rate then the packet per second (pps) value.
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. ● arp inspection — enable dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. Syntax Parameters clear ip dhcp snooping {binding | source-address-validation discardcounters [interface interface]} binding Clears the binding table.
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
ip dhcp relay Enable Option 82. Syntax Parameters Defaults ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82. remote-id port Enter the keywords remote-id port to configure the port as the remote id in option–82.
ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ipv6 dhcp snooping vlan Enable ipv6 DHCP Snooping on VLAN or range of VLANs.
interface type Enter the keyword interface then the type of interface to which the host is connected: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. lease time Defaults Enter the keyword lease then the amount of time the IP address are leased. The range is from 1 to 4294967295.
IPv6 DHCP Snooping Binding Create a static DHCP snooping binding entry in the snooping database. Syntax [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6address interface interface-type | interface-number lease value To delete the DHCP snooping binding entry from DHCP snooping database, use the [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease valuecommand.
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted.
To disable dhcp snooping trusted capability on this interface, use the no ipv6 dhcp snooping trust command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Added the keyword ipmac. 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system.
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface.
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
ipv6-address Default Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Enhanced to support non-default VRF configuration for DHCPv6 helper address. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
ipmac-vlan sav access-list on Port-channel 10 on stack-unit 3 Total cam count 5 permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) permit vlan 10 host 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) permit vlan 10 host 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) NOTE: The output for port-channel interfaces does not display the physical interface.
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. DellEMC# show ipv6 dhcp snooping IPv6 DHCP Snooping IPv6 DHCP Snooping Mac Verification : Enabled. : Disabled.
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to associate the system with one or more DNS servers.
Usage Information Example Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. DellEMC(conf)# ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrfname] name ip-address command.
Defaults None Command Modes EXEC Command History Usage Information Example 600 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • • • • • ecmp-group hash-algorithm hash-algorithm ecmp hash-algorithm seed ip ecmp-group ip ecmp weighted link-bundle-monitor enable link-bundle-distribution trigger-threshold show config show link-bundle distribution ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID.
● xor4: Use CRC16_BISYNC_AND_XOR4 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor4 ● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR hg { crc16 | crc16cc | Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices: crc32MSB | ● crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) crc32LSB | xor1 | ● crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT p
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Added flow-based-hashing support for hashing on ECMP for S4820T, S6000, S4048 and Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters Defaults crc-upper Uses the upper 32 bits of the key for the hash computation. The default is crclower. dest-ip Uses the destination IP for ECMP hashing. The default is enabled.
Parameters Defaults seed value Enter the keyword seed then the seed value. The range is from 0 to 2,147,483,646. stack–unit slot/ port Enter the keyword stack-unit then the slot/port[subport] number. port-set number Enter the keyword port-set then the port-pipe number. The value is 0. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Example DellEMC(conf)# ip ecmp ? weighted Enables Weighted ECMP DellEMC(conf)# ip ecmp weighted DellEMC(conf)#do show running-config | grep ecmp ip ecmp weighted DellEMC(conf)# DellEMC(conf)# no ip ecmp ? weighted Disables Weighted ECMP DellEMC(conf)# no ip ecmp weighted DellEMC(conf)# do show running-config | grep ecmp link-bundle-monitor enable Provides a mechanism to enable monitoring of traffic distribution on an ECMP link bundle.
Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
show link-bundle distribution Display the link-bundle distribution for the interfaces in the bundle, type of bundle (LAG or ECMP), and the most recently calculated interface utilization (either bytes per second rate or maximum rate) for each interface. Syntax show link-bundle-distribution Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: Topics: • • • • fips mode enable show fips status show ip ssh ssh fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes CONFIGURATION Command History Example This guide is platform-specific.
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256cbc,aes128-ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-sha1-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled.
● ● ● ● aes192–cbc: Force ssh to use the aes256–cbc encryption cipher. aes128–ctr: Force ssh to use the aes256–cbc encryption cipher. aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. 3des-cbc: Force ssh to use 3des-cbc encryption cipher. -l username (OPTIONAL) Enter the keyword —l then the user name used in this SSH session. The default is the user name of the user associated with the terminal. -m HMAC algorithm Enter one of the following HMAC algorithms to use. (For v2 clients only.
NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. Example If FIPS mode is not enabled: DellEMC# ssh 10.10.10.10 ? -c Encryption cipher to use (for v2 clients only) -l User name option -m HMAC algorithm to use (for v2 clients only) -p SSH server port option (default 22) -v SSH protocol version DellEMC# ssh 10.10.10.
17 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE enddevice and an FCF.
Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface.
ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 9.2(0.2) Introduced on the S4810 and S4820T. Added the receive parameters packettype and interfaces and their options.
fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN. Syntax fip-snooping enable To disable the FIP snooping feature on all or a specified VLAN, use the no fip-snooping enable command. Defaults FIP snooping is disabled on all VLANs. Command Modes ● CONFIGURATION ● VLAN INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. fip-snooping max-sessions-per-enodemac Configure the maximum session limit per ENode MAC address.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links. It is not recommended to use this command because multi-hop FSB is not supported.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
Field Description FCF MAC MAC address of the FCF. VLAN VLAN ID number the session uses. FC-ID Fibre Channel session ID the FCF assigns.
Example DellEMC# show fip-snooping fcf FCF MAC FCF Interface VLAN FC-MAP FKA_ADV_PERIOD No. of Enodes ------- ------------- ---- ------ -------------- ------------54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels.
Field Description Number of FLOGO Number of FIP-snoop FLOGO frames received on the interface Number of ENode Number of FIP-snoop ENode keep-alive frames received on the interface. Keep Alives Number of VN Port Keep Alives Number of FIP-snoop VN port (Virtual N-port) keep-alive frames received on the interface Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface.
Number of FLOGO Rejects :0 Number of CVL :0 Number of FCF Discovery Timeouts :0 Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int tengigabitethernet 1/11 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of FLOGI :1 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :4416 Number of VN Port Keep Alive
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
show fips status Display the FIPs status on the platform. Syntax show fips status Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
18 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol.
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
Version Description 7.4.1.0 Introduced. Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration. Ownership is relinquished for a port only when the interface does not play a part in any control VLAN, that is, the interface does not belong to any ring. Related Commands ● show frrp — display the Resilient Ring Protocol configuration information. member-vlan Specify the member VLAN identification numbers.
mode Set the Master or Transit mode of the ring. Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters Defaults master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
Usage Information Version Description 7.4.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
Related Commands ● protocol frrp — enter the resilient ring protocol and designate a ring identification. timer Set the hello interval or dead interval for the Ring control packets. Syntax timer {hello-interval milliseconds}| {dead-interval milliseconds} To remove the timer, use the no timer {hello-interval [milliseconds]}| {deadinterval milliseconds} command.
Usage Information The hello interval command is the interval at which ring frames are generated from the primary interface of the master node. The dead interval command is the time that elapses before a time-out occurs.
19 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax Parameters clear gvrp statistics interface interface interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
NOTE: Designate the milliseconds in multiples of 100. Defaults As above. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series ● disable — globally disable GVRP. show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific.
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. summary Defaults Enter the keyword summary to display just a summary of the GVRP statistics. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
Leave All Transmitted: 41 Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 DellEMC# Related Commands ● show gvrp — display the GVRP configuration.
20 High Availability (HA) High availability (HA) in the Dell EMC Networking OS is the configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol. You must specifically enable some protocols for HA.
Usage Information Enabling this command keeps the failed RPM in the failed state. If there are two RPMs in the system, enabling this command prevents the failed RPM from becoming a working Standby RPM. If there is only one RPM in the system, the failed RPM does not recover and affects the system. redundancy force-failover Force the secondary stack unit to become the primary stack unit.
Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. redundancy protocol Enable hitless protocols.
show redundancy Display the current redundancy configuration. Syntax show redundancy Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.0) Introduced on the M I/O Aggregator.
Field Description ● RPM failover counter (to reset the counter, use the redundancy resetcounter command) ● the time and date of the last RPM failover ● the reason for the last RPM failover Last Data Sync Record Displays the data sync information and the timestamp for the data sync: ● Start-up Config is the contents of the startup-config file. ● Line Card Config is the line card types configured and interfaces on those line cards. ● Runtime Event Log is the contents of the Event log.
21 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
Table 4. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 660 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
22 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. The access list accepted is an extended ACL.
Version Description 7.7.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion.
Version Description E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters Defaults seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax Parameters Defaults ip igmp version {2 | 3} 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. 2 (IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
Example Example (VLT) Field Description Uptime Displays the amount of time the group has been operational. Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. DellEMC# show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.0.
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
Inbound IGMP access group is not set Internet address is 35.0.0.1/24 IGMP is enabled on interface IGMP query interval is 60 seconds IGMP querier timeout is 125 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is enabled for all groups IGMP activity: 0 joins IGMP querying router is 35.0.0.
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
● IGMP snooping reacts to Layer 2 topology changes multiple spanning tree protocol (MSTP) triggers by sending a general query on the interface that comes in the FWD state. Important Points to Remember for IGMP Querier ● The IGMP snooping Querier supports version 2. ● You must configure an IP address to the VLAN interface for IGMP snooping Querier to begin.
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax debug ip igmp snooping [group address | interface] ● To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. ● To disable all debugging, use the undebug all command. Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to GroupLeave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters Defaults milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information.
show ip igmp snooping mrouter Display multicast router interfaces. Syntax Parameters show ip igmp snooping mrouter [vlan number] vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
23 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • • • Basic Interface Commands Egress Interface Selection (EIS) Commands Port Channel Commands Time Domain Reflectometer (TDR) Commands UDP Broadcast Commands ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. vrrp [ipv6 {vr-id} (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To | vr-id] clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
Related Commands ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear dampening Clear the dampening counters on all the interfaces or just the specified interface. Syntax clear dampening [interface] Parameters interface (OPTIONAL) Enter any of the following keywords and the interface information to clear counters from a specified interface: ● For a Port Channel interface, enter the keywords port-channel then a number.
Related Commands ● show interfaces dampening — display interface dampening information. ● dampening — configure dampening on an interface. dampening Configure dampening on an interface. Syntax Parameters Defaults dampening [[[[half-life] [reuse-threshold]] [suppress-threshold]] [maxsuppress-time]] half-life Enter the number of seconds after which the penalty is decreased. The penalty decreases half after the half-life period expires. The range is from 1 to 30 seconds. The default is 5 seconds.
as “down” by all static/dynamic Layer 2 and Layer 3 protocols. The penalty is exponentially decayed based on the half-life timer. After the penalty decays below the reuse threshold, the interface enables. The configured parameters are as follows: ● suppress-threshold should be greater than reuse-threshold ● max-suppress-time should be at least 4 times half-life NOTE: You cannot apply dampening on an interface that is monitoring traffic for other interfaces.
interface TenGigabitEthernet 1/5 description testconfig no ip address portmode hybrid switchport rate-interval 8 mac learning-limit 10 no-station-move no shutdown DellEMC(conf-if-te-1/5)# DellEMC(conf)# default interface tengigabitethernet 1/5 DellEMC(conf-if-te-1/5)# show config ! interface TenGigabitEthernet 1/5 no ip address shutdown Related Commands ● show running-config – display the current configuration. description Assign a descriptive text string to the interface.
Usage Information Version Description 7.4.1.0 Modified for E-Series: Revised from 78 to 240 characters. Important Points to Remember: ● To use special characters as a part of the description string, you must enclose the whole string in double quotes. ● Spaces between characters are not preserved after entering this command unless you enclose the entire description in quotation marks (“desc_text”).
Usage Information Version Description 6.4.1.0 Introduced This command applies to any physical interface with speed set to 10/100. NOTE: Starting with Dell EMC Networking OS version 7.8.1.0, when you use a copper SFP2 module with catalog number GP-SFP2-1T in the S25P model of the S-Series, you can manually set its speed with the speed command. When you set the speed to 10 Mbps or 100 Mbps, you can also execute the duplex command.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S4048–ON and S5048F-ON. This feature is applicable only for 10GBase-T optical ports. NOTE: It is not supported for stacking ports. enable stack-unit transceiver Enable the 10GBase-T optical port that is reset due to high temperature to normal mode.
Usage Information Version Description 9.3.0.0 Introduced on the S6000. 9.2(1.0) Introduced on the Z9500. To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction.
To remove the configured recovery time interval, use the no errdisable recovery interval seconds command. Parameters Defaults interval seconds Enter the keyword interval and the number of seconds to recover the interface from Err-disabled state. The range is from 30 to 86,400 seconds. The default is 300 seconds. 300 seconds. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
Defaults rx on tx off Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Added support for monitor session. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
● Speeds less than one Gig cannot be configured when the asymmetric flow control configuration is on. The following error is returned: Can’t configure speed <1G when Asymmetric flowcontrol is on, config ignored ● Dell EMC Networking OS only supports rx on tx on and rx off tx off for speeds less than one Gig (Symmetric). NOTE: If you use the disable rx flow control command, Dell EMC Networking recommends rebooting the system. NOTE: Dell EMC Networking OS does not support mirroring of tx pause frames.
off on on on off off on on off off on on off off on on off off on on off off on on off on on on off off on on interface Configure a physical or virtual interface on the switch. Syntax Parameters interface interface interface Enter one of the following keywords and the interface information: ● For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(2.0) Introduced on the S3100 series. 9.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
Usage Information Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a Management port. The Management port is enabled by default (no shutdown).
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete the Null interface. The only configuration command possible in a Null interface is ip unreachables. Example Related Commands DellEMC(conf)# interface null 0 DellEMC(conf-if-nu-0)# ● ● ● ● ● interface — configure a physical interface.
Usage Information Version Description 9.14(0.0) Updated the error message when no ports are configured within the specified interface range. 9.13(0.0) Introduced the Configuration Terminal Batch mode on C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P2) Introduced on the S4038-ON. 9.8(0.0P5) Introduced on the S3048-ON.
Example (Configuration Terminal Batch Mode) Example (Multiple Ports) Example (Overlapping Ports) Usage Information DellEMC(conf-b)#interface range te 1/1-4 DellEMC(conf-if-range-te-1/1-4)# DellEMC(conf)# interface range tengigabitethernet 2/10 - 2/23, tengigabitethernet 2/12 - 2/17 DellEMC(conf-if-range-te-2/10-2/23)# DellEMC(conf)# interface range tengigabitethernet 2/3 - 2/11, tengigabitethernet 2/3 - 2/23 DellEMC(conf-if-range-te-2/3-2/23)# Only VLAN and port-channel interfaces created using the inter
Secondary VLT Dec 6 10:43:17 %RPM1-P:CP %CLIBATCH-6CLI_BATCH_CONFIG_IN_PROGRESS_TRAP: Batch configuration commit is in progress Dec 6 10:43:18 %RPM1-P:CP %CLIBATCH-6-CLI_BATCH_CONFIG_COMPLETE_TRAP: Batch configuration commit is success Related Commands ● ● ● ● ● interface port-channel — configure a port channel group. interface vlan — configure a VLAN interface. show config (from INTERFACE RANGE mode) — display the bulk configuration interfaces. show range — display the bulk configuration ranges.
Example (Single Range) Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This example shows how to define an interface range macro named test.
Example (Single Range) Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced This example shows the macro named test that was defined earlier.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. For more information about VLANs and the commands to configure them, see Virtual LAN (VLAN) Commands. FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs and IP ACLs are supported. For more information, see Access Control Lists (ACL).
Usage Information You can configure the interface type as CR4 with auto-negotiation enabled. If a DAC cable link is down, you can resolve the issue by setting the interface type as CR4. Auto-negotiation is disabled by default. If the CR4 optic fails to come up, use the autoneg option. If a 40G CR4 interface does not come up, use the following commands: ● For ACU 40 G cables — use the no intf-type or intf-type cr4 command. ● For CU 40 G cables — use the intf-type cr4 autoneg command.
monitor interface Monitor counters on a single interface or all interfaces. The screen is refreshed every five seconds and the CLI prompt disappears. Syntax monitor interface [interface] To disable monitoring and return to the CLI prompt, press the q key. Parameters interface (OPTIONAL) Enter the following keywords and the interface information: ● For the Management interface on the stack-unit, enter the keyword managementEthernet then the slot/port information.
Example (Single Interface) Key Description systest-3 Displays the host name assigned to the system. monitor time Displays the amount of time since the monitor interface command was entered. time Displays the amount of time the chassis is up (since last reboot). m Change the view from a single interface to all interfaces on the line card or visaversa. c Refresh the view. b Change the counters displayed from Packets on the interface to Bytes.
Te 1/6 Up 4070 3 8680346 5 Te 1/7 Up 61934 34 138734357 72 Te 1/8 Up 61427 1 59960 1 Te 1/9 Up 62039 53 104239232 3 Te 1/10 Up 17740044091 372 7373849244 79 Te 1/11 Up 18182889225 44 7184747584 138 Te 1/12 Up 18182682056 0 3682 1 Te 1/13 Up 18182681434 43 6592378911 144 Te 1/14 Up 61349 55 86281941 15 Te 1/15 Up 59808 58 62060 27 Te 1/16 Up 59889 1 61616 1 Te 1/17 Up 0 0 14950126 81293 Te 1/18 Up 0 0 0 0 Te 1/19 Down 0 0 0 0 Te 1/20 Up 62734 54 62766 18 Te 1/21 Up 60198 9 200899 9 Te 1/22 Up 17304741100 315
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If the packet includes a Layer 2 header, the difference between the link MTU and IP MTU (ip mtu command) must be enough bytes to include the Layer 2 header. When you enter the no mtu command, Dell EMC Networking OS reduces the IP MTU value to 1536 bytes. Link MTU and IP MTU considerations for port channels and VLANs are as follows.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.
exit Exit from autoneg configuration mode mode Specify autoneg mode no Negate a command or set its defaults show Show autoneg configuration information DellEMC(conf-if-autoneg)# mode ? forced-master Force port to master mode forced-slave Force port to slave mode DellEMC(conf-if-autoneg)# Example (Configured) User Information DellEMC# show interfaces configured TenGigabitEthernet 1/18 is up, line protocol is up Hardware is DellEMCEth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interf
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command-Line Reference Guide. Version Description 9.14(2.3) Introduced on the C9000, S3048-ON, S3100 series, S4048-ON, S4048T-ON, S5048F-ON, S6000, S6000-ON, S6010-ON, S6100-ON, and Z9100-ON. To disable the timer on an individual interface, use the no port-delay-restore command.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
Example (Vlan) DellEMC(conf-if-vl-20)# interface vlan 10 DellEMC(conf-if-vl-10)# no untagged tengigabitethernet 1/1 DellEMC(conf-if-vl-10)# interface vlan 20 DellEMC(conf-if-vl-20)# no tagged tengigabitethernet 1/1 DellEMC(conf-if-vl-20)# interface tengigabitethernet 1/1 DellEMC(conf-if-te-1/1)# no portmode hybrid DellEMC(conf-if-vl-20)# rate-interval Configure the traffic sampling interval on the selected interface.
rate-interval (Configuration Mode) Configure the traffic sampling interval for all physical and logical port-channel interfaces globally. The support to configure rateinterval globally enables you to modify the default interval rate for all physical and logical interfaces at one time. Syntax rate-interval seconds Use the no rate-interval command to remove the sampling interval configuration. Parameters seconds Enter the number of seconds for which to collect traffic data.
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
-range (Optional) Enter the range of interfaces for which you want to view the information. The format is interface-type slot/port/[subport]-slot/ port/[subport] Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.3) Included the FEC types in the output for 25G, 50G, and 100G interfaces of the Z9100–ON. 9.14(0.
Usage Information Version Description 7.8.1.0 Output expanded to include SFP+ media on the C-Series. 7.6.1.0 Introduced on the S Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Changed the organization of the display output. 6.3.1.0 Added the Pluggable Media Type field in the E-Series output. Use the show interfaces command for details on a specific interface. NOTE: In the CLI output, the power value is rounded to a 3-digit value. For receive/transmit power that is less than 0.
Line Description ○ runts = number of packets that are less than 64B ○ giants = packets that are greater than the MTU size ○ throttles = packets containing PAUSE frames ● Number of CRC, overrun, and discarded packets: ○ CRC = packets with CRC/FCS errors ○ overrun = number of packets discarded due to FIFO overrun conditions ○ discarded = the sum of runts, giants, CRC, and overrun packets discarded without any processing Output Statistics: Displays output statistics sent out of the interface including: ● Nu
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
Virtual-IP is not set Virtual-IP IPv6 address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 10 Mbit, Mode full duplex ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 04:01:08 Queueing strategy: fifo Input 943 packets, 78347 bytes, 190 multicast Received 0 errors, 0 discarded Output 459 packets, 102388 bytes, 15 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:03:09 Example (Management Ethernet, two IPv6 addresses) DellEMC# sh
show interfaces configured Display any interface with a non-default configuration. Syntax show interfaces configured Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 00:04:59 DellEMC# show interfaces dampening Display interface dampening information. Syntax show interfaces dampening [[interface] [summary] [detail]] Parameters interface (Optional) Enter one of the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number.
Example Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
Usage Information Version Description 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. 6.5.4.
Speed: ● ● ● ● Example Auto 1000MB 100MB 10MB DellEMC# show interfaces tengigabitethernet 1/1 phy Mode Control: SpeedSelection: 10b AutoNeg: ON Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete: False RemoteFault: False LinkStatus: False JabberDetect: False AutoNegotation Advertise: 100MegFullDplx: True 100MegHalfDplx: True 10MegFullDplx: False 10MegHalfDplx: True Asym Pause: False Sym Pause: False AutoNegotiation Remote Partner's Ability: 100MegFullDplx: False
Example Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in nonON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range.
Te 1/2 Te 1/3 Te 1/4 Te 1/5 DellPort Te 1/6 Te 1/7 Te 1/8 Te 1/9 Te 1/10 Te 1/11 Te 1/12 Te 1/13 Te 1/14 Te 1/15 Te 1/16 DellEMC# Down Down Down Up Down Down Up Down Down Down Down Down Down Down Down Auto Auto Auto Auto Auto Auto 1000 Mbit Auto Auto Auto Auto Auto 1000 Mbit Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto 1 1 -30-130 --1502,1504,1506-1508,1602 -------- show interfaces switchport Display only virtual and physical interfaces in Layer 2 mode.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.
● show ip interface — display Layer 3 information about the interfaces. ● show interfaces transceiver — display the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show interfaces transceiver Display the details of an installed transceiver.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Output augmented with diagnostic data for pluggable media. 7.7.1.0 Removed three fields in the output: Vendor Name, Vendor OUI, and Vendor PN. 7.6.1.0 Introduced on the C-Series and S-Series. 6.5.4.0 Introduced on the E-Series.
Line Description Bias High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+.
Line Description Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above. Tx Bias High Alarm Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power High Alarm Flag This can be either true or false, depending on the Current Tx bias power value displayed above. Rx Power High Alarm Flag This can be either true or false, depending on the Current Rx power value displayed above.
SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP 0 0 0 0 0 0 0 0 0 0 0 0 0 Length(50um) 10m = 0x1e Length(62.
show interfaces vlan Display VLAN statistics. Syntax Parameters show interfaces vlan {vlan-id} [LINE] {description} vlan-id Enter the interface VLAN number. The range is from 1 to 4094. LINE (OPTIONAL) Enter the name of the VLAN. description Displays the VLAN interface information with description. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
show range Display all interfaces configured using the interface range command. Syntax show range Command Modes INTERFACE RANGE (config-if-range) Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. ● ecmp-group — configure a mechanism to monitor traffic distribution. show system stack-unit fanout configured Displays the details about the fanned-out ports.
To activate an interface, use the no shutdown command. Defaults The interface is disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
NOTE: This interface speed is not supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. If the command is entered for these interfaces, an error message appears. Defaults 100 Enter the keyword 100 to set the interface’s speed to 10/100 Mb/s. NOTE: When this setting is enabled, only 100Base-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s. Autonegotiation is enabled.
NOTE: Starting with Dell EMC Networking OS version 7.8.1.0, when you use a copper SFP2 module with catalog number GP-SFP2-1T in the S25P model of the S-Series, you can manually set its speed with the speed command. When you set the speed to 10 or 100 Mbps, you can also use the duplex command. If you use an active optical cable (AOC), you can convert the QSFP+ port to a 10 Gigabit SFP+ port or 1 Gigabit SFP port. Use the speed command to enable the required speed.
Related Commands ● interface ManagementEthernet — configure the Management port on the system (either the Primary or Standby RPM). ● management route — configure a static route that points to the Management interface or a forwarding router. stack-unit portmode quad Configures the list of dynamic fan-out capable ports. Syntax stack-unit [stack-unit number] port port-number portmode quad To remove the quad-port configuration, use the command. Parameters Defaults stack-unit number Enter the port number.
primary port fails, the backup port changes to the up state. If the primary later comes up, it becomes the backup. interface interface Defaults (OPTIONAL) Enter any of the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
Usage Information Version Description pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output. When you enter the switchport command, the interface is automatically added to the default VLAN.
Egress Interface Selection (EIS) Commands The following commands are Egress Interface Selection (EIS) commands. application Configure the management egress interface selection. Syntax application {all | application-type} To remove a management application configuration, use the no application {all | application-type} command. Parameters application-type Enter any of the following keywords: ● ● ● ● ● ● ● ● ● ● ● all Defaults For For For For For For For For For For For DNS, enter the keyword dns.
Parameters application-type Enter any of the following keywords: ● For HTTP, enter the keyword http. ● For ICMP, enter the keyword icmp. all Defaults Configure all applications. None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.
management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface. Syntax management egress-interface-selection To disable and remove management egress interface selection (EIS) configurations, use the no management egress-interface-selection command. Defaults None. Command Modes CONFIGURATION Command History This guide is platform-specific.
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T.
Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a Port Channel. ● The platform supports 128 port channels and 16 members per port channel.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Use the interface port-channel command to access this command. You cannot add an interface to a Port Channel if the interface contains an IP address in its configuration. Only the shutdown, description, mtu, and ip mtu commands can be configured on an interface if it is added to a Port Channel.
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series. 7.6.1.0 Introduced on S-Series. 7.5.1.0 Introduced on C-Series. pre-Version 6.2.1.0 Introduced on E-Series. Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by using the switchport command) or Layer 3 mode (by configuring an IP address). You can add a Port Channel in Layer 2 mode to a VLAN.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Usage Information This feature groups two LAGs to work in tandem as a supergroup.
show interfaces port-channel Display information on configured Port Channel groups. ` Syntax show interfaces port-channel [channel-number] [brief] [description] Parameters channel-number For a Port Channel interface, enter the keyword port-channel then a number. The range is from 1 to 128. NOTE: This command also enables you to view information corresponding to a range of ports. ● For port-channel interfaces, you can specify multiple ports as portrange.
Example Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fatesharing group (“Failover-group”) is listed. Hardware is... Displays the interface’s hardware information and its assigned MAC address. Port-channel is part... Indicates whether the LAG is part of a LAG fate-sharing group (“Failover-group”). Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed.
Output 00.02Mbits/sec,4 packets/sec Time since last interface status change: 00:22:34 DellEMC# User Information The following describes the show interfaces port-channel brief command shown in the following example. Field Description LAG Lists the port channel number. Mode Lists the mode: ● L3 — for Layer 3 ● L2 — for Layer 2 Status Displays the status of the port channel.
source-ip address destination-ip address source-port number destination-port number source-mac address destination-mac Enter the keywords source-ip then the IP source address in IP address format. Enter the keywords destination-ip then the IP destination address in IP address format. Enter the keywords source-port then the source port number. The range is from 1 to 65536. The default is None. Enter the keywords destination-port then the destination port number. The range is from 1 to 65536.
● Load-balance is configured for MAC ● Load-balance is configured for IP 4-tuple/2-tuple ● A non-IP payload is going out of Layer 2 LAG interface that is a member of VLAN with an IP address Example DellEMC# show port-channel-flow outgoing-port-channel 1 incominginterface te 3/3 source-mac 00:00:50:00:00:00 destination-mac 00:00:a0:00:00:00 Egress Port for port-channel 1, for the given flow, is Te 13/2 Time Domain Reflectometer (TDR) Commands TDR is useful for troubleshooting an interface that is not estab
Usage Information Version Description 7.7.1.0 Introduced on the S Series. 7.6.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The interface must be enabled to run the test or an error message is generated: DellEMC# tdr-cable-test tengigabitethernet 11/1 % Error: Interface is disabled Te 11/1. Syslog messages are generated when the link flaps during TDR tests. Related Commands ● show tdr — display the results of the TDR test. show tdr Display the TDR test results.
Example Related Commands Status Definition OK Status: Terminated TDR test is complete, no fault is detected on the cable, and the test is terminated. Length: 92 (+/1) meters, Status: Shorted A short is detected on the cable. The location, in this Example is 92 meters. The short is accurate to plus or minus one meter. Length: 93 (+/1) meters, Status: Open An opening is detected on the cable. The location, in this Example is 93 meters. The open is accurate to plus or minus one meter.
Example Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series. DellEMC# debug ip udp-helper UDP helper debugging is on 01:20:22: Pkt rcvd on Gi 3/0 with IP DA (0xffffffff) will be sent on Gi 5/1 Gi 5/2 Vlan 3 01:44:54: Pkt rcvd on Gi 4/0 is handed over for DHCP processing.
Usage Information Version Description Pre-version 8.3.7.0 Introduced on the E-Series. If you configure the ip helper-address command and ip udp-helper udp-port command, the behavior is that the UDP broadcast traffic with port numbers 67/68 is unicast relayed to the DHCP server per the ip helper-address configuration. This occurs regardless if the ip udp-helper udp-port command contains port numbers 67/68 or not.
To delete an interface, use theno ip http source-interface interface command. Parameters interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
24 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: ● Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
ahauthentication Enter the keywords ah-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. ● md5 — Use Message Digest 5 (MD5) authentication. ● sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. ● null — Causes an encryption policy configured for the area to not be inherited on the interface.
crypto ipsec policy Create a crypto policy used by ipsec. Syntax crypto ipsec policy name seq-num ipsec-manual To delete a crypto policy entry, use the no crypto ipsec policy name seq-num ipsecmanual command. Parameters Defaults name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
Version Description 9.2(1.0) Introduced on the Z9500. match Apply an match filter to the crypto policy. Syntax match seq-num tcp [sourceip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] To remove the match filter for the crypto map, use the no match seq-num tcp [source ip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] command.
session-key Specify the session keys used in the crypto policy entry. Syntax session-key {inbound | outbound} {ah spi hex-key-string | esp spi encrypt hex-key-string auth hex-key-string To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters Defaults name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec.
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500. DellEMC# show crypto ipsec transform-set Transform-Set Name Transform-Set refCnt AH Transform ESP Auth Transform ESP Encry Transform DellEMC# : dallas : 0 : : : 3des show crypto ipsec policy Display the crypto policy configuration.
Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num : : : : : : : : 1.1.1.1 /32 0 1.1.1.2 /32 23 DellEMC(conf-crypto-policy)# transform-set Specify the transform set the crypto policy uses. Syntax transform-set transform-set-name To delete a transform set from the crypto policy, use the no transform-set transform-setname command.
25 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
• • • • • • show show show show show show ip protocols ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid. You can use the vrf attribute of this command to create a static ARP entry on either a default or a nondefault VRF.
Version Description 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands ● show arp retries — display the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
arp max-entries Enables you to configure the maximum number of ARP entries per VRF that are allowed for IPv4.. Syntax Parameters Defaults arp max-entries [vrf vrf-name] max-number vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows. max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Not configured.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM).
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.) Syntax Parameters clear ip fib stack-unit unit-number vrf vrf-name unit-number Enter the number of the stack unit.
Parameters vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to clear the routes corresponding to that VRF. * Enter an asterisk (*) to clear all learned IP routes. ip-address mask Enter a specific IP address and mask in dotted decimal format to clear that IP address from the routing table. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
Parameters all Enter the keyword all to clear all TCP statistics maintained on all switch processors. cp (OPTIONAL) Enter the cp to clear only statistics from the Control Processor. rp (OPTIONAL) Enter the keyword rp to clear only the statistics from Route Processor. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
count value Defaults (OPTIONAL) Enter the keyword count then the count value. The range is from 1 to 65534. None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
to 113.3.3.254 DellEMC# Related Commands ● ip helper-address – specify the destination broadcast or host address for the DHCP server request. ● ip helper-address hop-count disable – disable the hop-count increment for the DHCP relay agent. debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command.
Command Modes EXEC Privilege Command History Example Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
count value (OPTIONAL) Enter the keyword count then the count value. The range is from 1 to 65534. The default is Infinity. interface (OPTIONAL) Enter the following keywords and the interface information: ● ● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
Field Description multicast proto, unroutable TCP src= Displays the source and destination ports, the sequence number, the acknowledgement number, and the window size of the packets in that TCP packets. UDP src= Displays the source and destination ports for the UDP packets. ICMP type= Displays the ICMP type and code.
%IPMGR-3-DEBUG_IP_PACKET_ACL_AMBIGUOUS_EXP: Ambiguous rules not supported in access-list debug, access-list debugging is turned off DellEMC# icmp6-redirect enable Enable ICMP and ICMP6 redirects. Syntax icmp6-redirect enable Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You must be in INTERFACE mode before you add an IP address to an interface. Assign an IP address to an interface prior to entering ROUTER OSPF mode.
ip domain-list Configure names to complete unqualified host names. Syntax ip domain-list name To remove the name, use the no ip domain-list name command. Parameters Defaults name Enter a domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
ip domain-lookup To address resolution (that is, DNS), enable dynamic host-name. Syntax ip domain-lookup To disable DNS lookup, use the no ip domain-lookup command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
To remove the domain name, use the no ip domain-name command. Parameters Defaults name Enter one domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Parameters Defaults ip-address Enter an IP address in dotted decimal format (A.B.C.D). Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
● For a Management Ethernet interface, enter the keyword managementethernet. NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
Example DellEMC(conf)# ipv6 icmp source-interface tengigabitethernet 1/1 DellEMC(conf)# ip max-frag-count Set the maximum number of fragments allowed in one packet for packet re-assembly. Syntax ip max-frag-count count To place no limit on the number of fragments allowed, use the no ip max-frag-count command. Parameters Defaults count Enter a number for the number of fragments allowed for re-assembly. The range is from 2 to 256. No limit is set on number of fragments allowed.
ip max-routes Enables you to configure the maximum number of protocol routes per VRF that are allowed for IPv4. Syntax Parameters Defaults ip max-routes [vrf vrf-name] max-number vrf vrf-name Enter the keyword vrf and then the name of the VRF for which you want to configure maximum number of protocol routes that IPv4 allows. max-number Enter the maximum number of protocol routes that a VRF RTM can hold. The range is from 0 to 7500. Not configured.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● show ip interface — display the interface routing status and configuration. ip route Assign a static route to the switch.
interface ip- address distance Enter the keyword interface then the IP address. (OPTIONAL) Enter the value of the distance metric assigned to the route. The range is from 1 to 255. name description (OPTIONAL) Enter the keyword name and the description for the IPv4 static route configuration. permanent (OPTIONAL) Enter the keyword permanent to specify that the route must not be removed even if the interface assigned to that route goes down.
Usage Information Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Using the following example of a static route: ip route 33.33.33.0 /24 tengigabitethernet 1/1 172.31.5.43 ● The software installs a next hop that is not on the directly connected subnet but which recursively resolves to a next hop on the interface’s configured subnet.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
vlan | L4-source- ● dest-port-id — Use dest-port-id field in hash calculation. port | L4-dest● dest-module-id — Use dest-module-id field in hash calculation. port ] ● protocol — Use IPv4 protocol field in hash calculation. ● vlan — Use vlan field in hash calculation. ● L4-source-port — Use IPv4 L4-source-port field in hash calculation. ● L4-dest-port — Use IPv4 L4-dest-port field in hash calculation.
management route Configure a static route that points to the Management interface or a forwarding router. Syntax management route {ip-address mask | ipv6-address 1.1.1.1prefix-length} {forwarding-router-address | managementethernet | fortyGigE | vlan | tengigabitethernet } To remove a static route, use the no management route command. Parameters ip-address mask Enter an IP address (dotted decimal format) and mask (/prefix format) of the destination subnet.
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix are not reflected in the hardware routing tables. Separate routing tables are maintained for IPv4 and IPv6 management routes.
Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Description CPU Example Example (Private VLAN) Lists which CPU the entries are stored on. DellEMC> show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU ------------------------------------------------------------Internet 192.2.1.254 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.253 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.252 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.251 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.250 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.
Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6 addresses. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show hosts command in the following example. Field Description Default domain... Displays the domain name (if configured).
show ip cam stack-unit Display CAM entries for a port-pipe of a stack-unit on a S-Series or Z-Series switch. Syntax show ip cam stack-unit {stack-unit-number} [port-set {pipe-number} | vrf vrf-name {ip-address mask [longer-prefixes [ecmp-group detail]]}| ecmpgroup {detail | member-info [detail [group-index index-number]]}| summary] Parameters stack-unitnumber Enter the stack-unit ID. The unit ID range is from 1 to 6.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. The following describes the show ip cam command shown in the following example. Field Description Destination Displays the destination route of the index. EC Displays 1 if the route is an ECMP route. Else, displays 0. C This is the CPU bit. If it displays 1, then it indicates that a packet hitting this entry will be forwarded to the CPU. V Id Displays the VLAN ID. If the entry is 0, the entry is not part of a VLAN.
Parameters stack-unitnumber Enter the stack unit ID. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view FIB entries corresponding to that VRF. ip-address mask (OPTIONAL) Enter the IP address of the network destination to view only information on that destination. Enter the IP address in dotted decimal format (A.B.C.D). Enter the mask in slash prefix format (/X). longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix.
If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named W-EC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is assigned with a weight. Example DellEMC# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC ------------------------------------------------------------------------------------------1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Te 3/42 1000 0 2.1.1.2/32 via 2.1.1.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number.
Example DellEMC# show ip interface tengigabitethernet 1/1 TenGigabitEthernet 1/1 is down, line protocol is down Internet address is not set IP MTU is 1500 bytes Directed broadcast forwarding is disabled Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# DellEMC# show ip interface port-channel 128 Port-channel 128 is down, line protocol is down Internet address is 10.1.1.
TenGigabitEthernet 1/7 down unassigned NO Manual administratively down show ip management-route View the IP addresses assigned to the Management interface. Syntax Parameters show ip management-route [all | connected | summary | static] all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
172.16.1.0/24 DellEMC# 10.1.2.4 Active show ipv6 management-route Display the IPv6 static routes configured for the management interface. Syntax show ipv6 management-route [all | connected | summary | static] Parameters all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
show ip protocols View information on all routing protocols enabled and active on the switch. Syntax show ip protocols Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
show ip route View information, including how they were learned, about the IP routes on the switch. Syntax show ip route [vrf vrf-name] hostname | ip-address [mask] [longer-prefixes] | list prefix-list | protocol [process-id | routing-tag] | all | connected | static | summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the VRF name to list the routes in the route table of a specific VRF.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
Field Description Last Change Identifies when the route was last changed or configured.
L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set Destination Gateway Last Change --------------------------S 1.1.1.0/24 4.4.4.2, via Te 1/4 , weight 100 6.6.6.2, via Te 1/16, weight 200 C 4.4.4.0/24 Direct, Te 1/4 C 6.6.6.0/24 Direct, Te 1/16 Dist/Metric ----------1/0 00:00:01 0/0 0/0 00:01:32 00:01:25 DellEMC# show ip route 1.1.1.0/24 Routing entry for 1.1.1.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
Total 2 non-active route(s) using 128 bytes DellEMC> Related Commands ● show ip route — display information about the routes found in the switch. show ip traffic View IP, ICMP, UDP, TCP and ARP traffic statistics. Syntax show ip traffic [all | cp | rp1 | rp2] NOTE: These options are supported only on the E-Series. Parameters all (OPTIONAL) Enter the keyword all to view statistics from all processors. If you do not enter a keyword, you also view all statistics from all processors.
Usage Information The following describes the show ip traffic summary shown in the following example. Keyword Definition unknown protocol... No receiver for these packets. Counts packets whose protocol type field is not recognized by Dell EMC Networking OS. not a gateway... Packets can not be routed; the host/network is unreachable. security failures...
ICMP statistics: Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0 unreachable 0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench 0 parameter, 0 timestamp, 0 info request, 0 other Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply 0 mask requests, 0 mask replies, 0 quench, 0 timestamp 0 info reply, 0 time exceeded, 0 parameter problem UDP statistics: Rcvd: 0 total, 0 checksum errors, 0 no port 0 short packets, 0 bad length, 0 no port broadcasts, 0 socket full Sent: 0 total, 0 forward
Field Description Rcvd: Displays the number and types of TCP packets received by the switch. ● Total = total packets received ● no port = number of packets received with no designated port 0 checksum error... Example Displays the number of packets received with the following: ● checksum errors ● bad offset to data ● too short 329 packets... Displays the number of packets and bytes received in sequence. 17 dup... Displays the number of duplicate packets and bytes received. 0 partially...
0 partially dup packets (0 bytes) 7 out-of-order packets (0 bytes) 0 packets ( 0 bytes) with data after window 0 packets after close 0 window probe packets, 41 window update packets 41 dup ack packets, 0 ack packets with unsend data 10184 ack packets (12439508 bytes) Sent: 12007 Total, 0 urgent packets 25 control packets (including 24 retransmitted) 11603 data packets (12439677 bytes) 24 data packets (7638 bytes) retransmitted 355 ack only packets (41 delayed) 0 window probe packets, 0 window update packets
26 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
Ipv4Qos : L2Qos : 2 3 -- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
Defaults permit Enter the keyword permit to configure a filter to forward packets meeting this condition. deny Enter the keyword deny to configure a filter to drop packets meeting this condition. ospfv3 Specify that this ACL is for OSPFv3 control plane traffic All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
● L3 ACL (ipv4acl: 1 ● IPv6 L3 ACL (ipv6acl): 2 l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
cam-acl Allocate space for IPv6 ACLs. Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: ● ● ● ● ● l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 L3 ACL (ipv4acl): 6 L2 ACL(l2acl): 5 IPv6 L3 ACL (ipv6acl): 0 L3 QoS (ipv4qos): 1 L2 QoS (l2qos): 1 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
27 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
Command Modes CONFIGURATION Command History Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048–ON. 9.8(0.0P2) Introduced on the S3048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can partition the LPM table to store IPv6 prefixes greater than /64 mask length.
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have. Syntax maximum dynamic-routes—ipv6 limit {warn-threshold threshold-value | warningonly} To remove the limit on the maximum number of IPv6 routes used, use the no maximum dynamicroutes-ipv6 command.
ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface. Syntax ipv6 address autoconfig To disable the address autoconfig operation on the management interface, use the no ipv6 address autoconfig command. Default Disabled Command Modes INTERFACE (management interface only) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1(0.0) Updated Usage Information. 9.0.0.0 Introduced on the Z9000. 8.3.19.
To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address {ipv6-address prefix-length} eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ipv6 flowlabel-zero Configure system to set the flow label field in the packets to zero. Syntax ipv6 flowlabel-zero To disable the 0 from being set in the field and allow the protocol operations to fill the field, use the no ipv6 flowlabel-zero command. Default Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series. ipv6 name-server Enter up to six IPv6 addresses of name servers. The order you enter the addresses determines the order of their use.
ipv6 nd dad attempts To perform duplicate address detection (DAD) on an interface, configure the number of neighbor solicitation messages that are sent. Syntax ipv6 nd dad attempts {number of attempts} To restore the default value, use the no ipv6 nd dad attempts command. Parameters Default number of attempts Enter the number of attempts to be made to detect a duplicate address. The range is from 0 to 15. Setting the value to 0 disables DAD on the interface.
Parameters Defaults ipv6-RDNSSaddress Enter the IPv6 Recursive DNS Server’s (RDNSS) address. You can specify up to 4 IPv6 RDNSS server addresses. lifetime Enter the lifetime in seconds. The amount of time the IPv6 host can use the IPv6 RDNSS address for name resolution. The range is 0 to 4294967295 seconds. When you specify the maximum lifetime value of 4294967295 or infinite, the lifetime does not expire. A value of 0 indicates to the host that the RDNSS address should not be used.
no-rtr-address Enter the keyword no-rtr-address to exclude the full router address from router advertisements (the R bit is not set). off-link Enter the keywords off-link to advertise the prefix without stating to recipients that the prefix is either on-link or off-link. valid-lifetime | infinite Enter the amount of time that the prefix is advertised, or enter infinite for an unlimited amount of time. The range is from 0 to 4294967295. The default is 2592000.
ipv6 route Establish a static IPv6 route. Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [name description] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.2) Added the keyword name for static routes. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
ipv6 unicast-routing Enable IPv6 unicast routing on the device. Syntax ipv6 unicast-routing To disable unicast routing, use the no ipv6 unicast-routing command. Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
NOTE: If you do not specify this option, IPv6 CAM entries corresponding to the default VRF are displayed. unit-number Enter the stack unit’s ID number. port-set Enter the keyword Port Set. summary (OPTIONAL) Enter the keyword summary to display a table listing network prefixes and the total number prefixes which can be entered into the IPv6 CAM. index (OPTIONAL) Enter the index in the IPv6 CAM.
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ● ipv6 flowlabel-zero — configure IPv6 address auto-configuration for the management interface. show ipv6 fib stack-unit View all FIB entries.
show ipv6 flowlabel-zero Display the flow label zero setting. Syntax show ipv6 flowlabel-zero Default Disabled Command Modes EXEC Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Defaults tengigabitethern et (OPTIONAL) View information for an IPv6 tengigabitethernet interface. fortyGigE (OPTIONAL) View information for an IPv6 fortygigabitethernet interface. stack-unit id (OPTIONAL) View information for stacking. tunnel tunnel-id (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 868 IPv6 Basics This guide is platform-specific.
ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 IPv6 unicast RPF check is not supported DellEMC# DellEMC# show ipv6 interface port-channel 128 Port-channel 128 is down, line protocol is down IPV6 is enabled Link Local address: fe80::201:e8ff:fe8a:e846 Global Unicast address(es): a
Remaining lifetime: infinite Virtual-IP IPv6 address is not set Global Anycast address(es): Joined Group address(es): ff02::1 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds ND retransmit interval is 1000 milliseconds ND hop limit is 64 DellEMC# Example (Brief) Example (Tunnel) DellEMC# show ipv6 interface brief TenGigabitEthernet 1/2 [administratively dow
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
Defaults hostname (OPTIONAL) View information for this IPv6 routes with Host Name. all (OPTIONAL) View information for all IPv6 routes. bgp (OPTIONAL) View information for all IPv6 BGP routes. connected (OPTIONAL) View only the directly connected IPv6 routes. isis (OPTIONAL) View information for all IPv6 IS-IS routes. list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes.
Field Description ● ● ● ● ● ● ● ● ● ● ● ● ● ● Example (SSeries) LO = Locally Originated O = OSPF IA = OSPF inter-area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes Destination Identifies the route’s destination IPv6 address.
trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults None Command Modes CONFIGURATION-POLICY-MAP-IN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
28 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters Defaults time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
ip-address (Optional) Defaults Enter the ip-address that the iSCSI monitors. The ip-address specifies the IP address of the iSCSI target. 860, 3260 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.
-----------------------------------------------iSCSI Targets and TCP Ports: -----------------------------------------------TCP Port Target IP Address 3260 860 Related Commands ● show iscsi session — display information about active iSCSI sessions on the switch. ● show iscsi session detailed — display detailed information about active iSCSI sessions on the switch. ● show run iscsi — show run iscsi. show iscsi session Display information about active iSCSI sessions on the switch.
● show iscsi session detailed — display detailed information about active iSCSI sessions on the switch. ● show run iscsi — show run iscsi. show iscsi session detailed Display detailed information on active iSCSI sessions on the switch. Syntax Parameters show iscsi session detailed [session isid] isid Enter the session’s iSCSi ID to display detailed information about the specified iSCSi session.
show run iscsi Display all globally configured non-default iSCSI settings in the current Dell EMC Networking OS session. Syntax show run iscsi Command Modes EXEC Privilege Command History Related Commands 882 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.
29 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain. ● isis password — configure an authentication password for an interface.
tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command.
debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies. Syntax debug isis [vrf vrf-name] adj-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name]adj-packets [interface] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details.
To turn off debugging, use the no debug isis [vrf vrf—name] updates [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF. This information contains local updates tied to the VRF that you specify. This command displays the local LSP debugging details of the current unit.
Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable debugging information on ISIS for CSNP/PSNP packets tied to that VRF. The command displays the SNP (CSNP/PSNP) related debugging information. interface (OPTIONAL) Identifies the interface type as one of the following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. When you use this command to redistribute routes into a routing domain, the router becomes an autonomous system (AS) boundary router. An AS boundary router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one.
Related Commands Version Description pre-7.7.1.0 Introduced. ● router isis — enter ROUTER mode on the switch. distance Define the administrative distance for learned routes. Syntax distance weight [ip-address mask [prefix-list]] To return to the default values, use the no distance weight command. Parameters Defaults weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability.
distribute-list in Filter network prefixes received in updates. Syntax distribute-list prefix-list-name in [interface] To return to the default values, use the no distribute-list prefix-list-name in [interface] command. Parameters prefix-list-name Specify the prefix list to filter prefixes in routing updates.
distribute-list out Suppress network prefixes from being advertised in outbound updates. Syntax distribute-list prefix-list-name out [connected | bgp as number | ospf process-id | rip | static] To return to the default values, use the no distribute-list prefix-list-name out [bgp as number connected | ospf process-id | rip | static] command. Parameters Defaults prefix-list-name Specify the prefix list to filter prefixes in routing updates.
distribute-list redistributed-override Suppress flapping of routes when the same route is redistributed into IS-IS from multiple routers in the network. Syntax distribute-list redistributed-override in To return to the default, use the no distribute-list redistributed-override in command. Defaults none Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information This guide is platform-specific.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced on the E-Series. Every graceful restart enabled router’s HELLO PDUs includes a restart TLV. This restart enables (re)starting as well as the existing ISIS peers to detect the GR capability of the routers on the connected network.
Version Description 8.3.1.0 Introduced on the E-Series. graceful-restart restart-wait Enable the graceful restart maximum wait time before a restarting peer comes up. Syntax NOTE: Set the t3 timer to adjacency on the restarting router when implementing this command. graceful-restart restart-wait seconds To return to the default, use the no graceful-restart restart-wait command. Parameters Defaults seconds Enter the graceful restart time in seconds. The range is from 5 to 300 seconds.
Parameters Defaults interval Enter the keyword interval to set the wait time. The range is from 5 to 120 seconds. The default is 5 seconds. retry-times Enter the keywords retry-times to set the number of times the request interval is extended until a CSNP is received from the helping router. The range is from 1 to 10 attempts. The default is 1. See Parameters. Command Modes ROUTER ISIS Command History This guide is platform-specific.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. The running router sets the remaining time value to the current adjacency hold time. You can override this setting by implementing this command. Override the default restart-wait time by entering the no graceful-restart restart-wait command. When you disable restart-wait, the current adjacency hold time is used.
Usage Information IS-IS hellos are padded to the full maximum transmission unit (MTU) size. Padding IS-IS Hellos (IIHS) to the full MTU provides early error detection of large frame transmission problems or mismatched MTUs on adjacent interfaces. Related Commands ● isis hello padding — turn ON or OFF hello padding on an interface basis. hostname dynamic Enables dynamic learning of hostnames from routers in the domain and allows the routers to advertise the hostname in LSPs.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced. To assign a network entity title to enable IS-IS, use the net command. This command accepts even if an IP address is not configured. This command is cached in the L3 Manager till the IP address is configured.
Usage Information Version Description 7.5.1.0 Introduced on the E-Series. Configure a network entity title (the net command) to specify the area address and the router system ID. To establish adjacencies and establish dynamic routing, enable routing on one or more interfaces. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
Usage Information Because the default establishes Level 1 and Level 2 adjacencies, you do not need to configure this command. Routers in an IS-IS system must be configured as a Level 1-only, Level 1-2, or Level 2-only system. Only configure interfaces as Level 1 or Level 2 on routers that are between areas (for example, a Level 1-2 router) to prevent the software from sending unused hello packets and wasting bandwidth.
isis hello-interval Specify the length of time between hello packets sent. Syntax isis hello-interval seconds [level-1 | level-2] To return to the default values, use the no isis hello-interval [seconds] [level-1 | level-2] command. Parameters Defaults seconds Allows you to set the length of time between hello packet transmissions. The range is from 1 to 65535. The default is 10. level-1 (OPTIONAL) Select this value to configure the hello interval for Level 1. This value is the default.
Parameters Defaults multiplier Specifies an integer that sets the multiplier for the hello holding time. Never configure a hello-multiplier lower than the default (3). The range is from 3 to 1000. The default is 3. level-1 (OPTIONAL) Select this value to configure the hello multiplier independently for Level 1 adjacencies. This value is the default. level-2 (OPTONAL) Select this value to configure the hello multiplier independently for Level 2 adjacencies.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Dell EMC Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis metric Assign a metric to an interface.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Dell EMC Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics.
Parameters Defaults encryption-type (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password. level-1 (OPTIONAL) Independently configures the authentication password for Level 1. The router acts as a station router for Level 1 routing. This setting is the default. level-2 (OPTIONAL) Independently configures the authentication password for Level 2.
level-2 Defaults (OPTIONAL) Specify the priority for Level 2. value = 64; level-1 (if not otherwise specified). Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. This command allows you to monitor adjacency state changes, which are useful when you monitor large networks. Messages are logged in the system’s error message facility. lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs).
Usage Information LSP throttling slows down the frequency at which LSPs are generated during network instability. Even though throttling LSP generations slows down network convergence, no throttling can result in a network not functioning as expected. If network topology is unstable, throttling slows down the scheduling of LSP generations until the topology regains its stability.
lsp-refresh-interval Set the link state PDU (LSP) refresh interval. LSPs must be refreshed before they expire. When the LSPs are not refreshed after a refresh interval, they are kept in a database until their max-lsp-lifetime reaches zero and then LSPs is purged. Syntax lsp-refresh-interval seconds To restore the default refresh interval, use the no lsp-refresh-interval command. Parameters Defaults seconds The LSP refresh interval, in seconds.
Parameters Defaults number Set the maximum number of manual area addresses. The range is from 3 to 6. The default is 3. 3 addresses Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Change the maximum LSP lifetime with this command.
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.0 Introduced. metric-style To generate and accept old-style, new-style, or both styles of type, length, and values (TLV), configure a router.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. If you enter the metric-style wide command, the Dell EMC Networking OS generates and accepts only new-style TLVs. The router uses less memory and other resources rather than generating both oldstyle and new-style TLVs. The new-style TLVs have wider metric fields than old-style TLVs. When wide transition is configured, narrow metric is sent for the narrow metric TLV and the actual wide metric is sent in wide metric TLV.
net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start. Syntax net network-entity-title To remove a net, use the no net network-entity-title command. Parameters Defaults network-entitytitle Specify the area address and system ID for an IS-IS routing process. The first 1 to 13 bytes identify the area address. The next 6 bytes identify the system ID.
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level-1-2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes. This setting is the default. route-map map- (OPTIONAL) If you do not enter the route-map argument, all routes are redistributed. If a map-name value is not specified, no routes are imported.
redistribute bgp Redistribute routing information from a BGP process. Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metricvalue] [metric-type {external| internal}] [route-map map-name] To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter a number that corresponds to the autonomous system number. The range is from 1 to 65355.
Usage Information Example Version Description 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command. You can “set” more advanced options using route maps.
Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.0 Introduced.
clns host ISIS 49.0000.0001.F100.E120.0013.00 log-adjacency-changes net 49.0000.0001.F100.E120.0013.00 ! address-family ipv6 unicast maximum-paths 16 multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family Example (AddressFamily_IPv6) The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode.
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added supported for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810.
Example The bold sections identify that MultiTopology IS-IS is enabled. DellEMC# show isis database IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x00000006 0xCF43 580 0/0/0 IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x00000006 0xCF43 580 0/0/0 ! DellEMC# show isis database detail ISIS.00-00 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.
show isis graceful-restart detail Display detailed IS-IS graceful restart related settings. Syntax show isis [vrf vrf-name] graceful-restart detail Command Modes ● EXEC ● EXEC Privilege Parameters Command History Example vrf vrf-name (Optional) Enter the keyword vrf followed by the name if the VRf to display IS-IS graceful restart details corresponding to that VRF. NOTE: If you do not specify this option, the IS-IS graceful restart details corresponding to the default VRF are displayed.
show isis hostname Display IS-IS host names configured or learned on the switch. Syntax show isis [vrf vrf-name] hostname Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IS-IS host names corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
show isis neighbors Display information about neighboring (adjacent) routers. Syntax show isis [vrf vrf-name] neighbors [level-1 | level-2] [detail] [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display adjacent router information corresponding to that VRF. level-1 (OPTIONAL) Displays information about Level 1 IS-IS neighbors. level-2 (OPTIONAL) Displays information about Level 2 IS-IS neighbors.
Example Field Description Interface The interface, slot, and port in which the router was discovered. State The value providing status about the adjacency state. The range is Up and Init. Type This value displays the adjacency type (Layer 2, Layer 2 or both). Priority IS-IS priority the neighbor advertises. The neighbor with highest priority becomes the designated router for the interface. Uptime Displays the interfaces uptime.
Example Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The bold section identifies that Multi-Topology IS-IS is enabled. DellEMC# show isis protocol IS-IS Router: System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.0000.0001 Routing for area address(es): 49.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000.
IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: DellEMC# Level-2 LSPs sourced (new/refresh) : 1/3 Level-1 LSPs flooded (sent/rcvd) : 0/0 Level-2 LSPs flooded (sent/rcvd) : 5934/5217 Level-1 LSPs CSNPs (sent/rcvd) : 0/0 Level-2 LSPs CSNPs (sent/rcvd) : 472/238 Level-1 LSPs PSNPs (sent/rcvd) : 0/0 Level-2 LSPs PSNPs (sent/rcvd) : 10/337 Level-1 DR Elections : 4 Level-2 DR Elections : 4 Level-1 SPF Calculations : 0 Level-2 SPF Calculations : 389 LSP checksum errors r
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for multi-topology ISIS. 7.5.1.0 Added support for SPF Throttling Enhancement. This command spf-interval in CONFIG-ROUTER-ISIS-AF-IPV6 mode is used for IPv6 Multi-Topology route computation only.
30 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on).
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session. Syntax lacp long-timeout To reset the timeout period to a short timeout (1 second), use the no lacp long-timeout command. Defaults 1 second Command Modes INTERFACE (conf-if-po-number) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Defaults 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. port-channel-protocol lacp Enable LACP on any LAN port.
show lacp Display the LACP matrix. Syntax show lacp port-channel-number [sys-id | counters] Parameters Defaults port-channelnumber Enter a port-channel number. The range is from 1 to 128. sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters. Without a Port Channel specified, the command clears all Port Channel counters.
Port Te 1/6 is enabled, LACP is Actor Admin: State ACEHJLMP Oper: State ACEGIKNP Partner Admin: State BDFHJLMP Oper: State BCEGIKNP DellEMC# Example (Sys-id) enabled and mode is lacp Key 1 Priority 128 Key 1 Priority 128 Key 0 Priority 0 Key 1 Priority 128 DellEMC# show lacp 1 sys-id Actor System ID: Priority 32768, Address 0001.e800.a12b Partner System ID: Priority 32768, Address 0001.e801.
31 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically.
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
● show mac-address-table aging-time — display the MAC aging time. mac-address-table disable-learning Disable MAC address learning from LACP or LLDP BPDUs. Syntax mac-address-table disable-learning [lacp | lldp] Parameters Defaults lacp Enter lacp to disable MAC address learning from LACP BPDUs. lldp Enter LLDP to disable MAC address learning from LLDP BPDUs. Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. vlan vlan-id Defaults Enter the keyword vlan then a VLAN ID number from 1 to 4094. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
interval seconds Defaults Enter the keyword interval then the number of seconds. The range is from 5 to 60. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.5.1.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. For more information about using this command, see NIC Teaming in the Layer 2 section of the Dell EMC Networking OS Configuration Guide. mac learning-limit Limit the maximum number of MAC addresses (static + dynamic) learned on a selected interface.
Usage Information Version Description 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added the station-move option. 6.5.1.0 Added support for MAC Learning-Limit on the LAG. This command and its options are supported on physical interfaces, static LAGs, LACP LAGs, and VLANs. If you do not specify the vlan option, the MAC address counters are not VLAN-based.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information If you configure mac-learn-limit and the sticky MAC feature is enabled, dynamically learned MAC addresses are converted to sticky for that port. Any new MAC address that is learned also becomes sticky for that port. Related Commands ● show mac learning-limit — display the details of the mac learning-limit.
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands ● show mac learning-limit — display details of the mac learning-limit. mac learning-limit reset Reset the MAC address learning-limit error-disabled state.
mac port-security Enable or disable the port security feature globally in the system. Syntax mac port-security To disable the port security, use the no mac port-security command. Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. pre-6.2.1.1 Introduced on the E-Series. show cam mac linecard (dynamic or static) Display the CAM size and the portions allocated for MAC addresses and for MAC ACLs.
Example Version Description 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. interface interface-type (OPTIONAL) Instead of entering the keyword interface then the interface type, slot/port[/subport] information, as above, you can enter the interface type, then just a slot number.
Column Heading Description Interface Displays the interface type and slot/port[/subport] information. The following abbreviations describe the interface types: ● Po = port channel ● Te = ten-gigabit Ethernet ● Fo = forty-gigabit Ethernet State Example Usage Information Example (Count) Related Commands Lists if the MAC address is in use (Active) or not in use (Inactive).
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. pre-6.2.1.1 Introduced on the E-Series.
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
default vlan-id Specify a VLAN as the Default VLAN. Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters Defaults vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
Example DellEMC(conf-if-vl-100)# show config ! interface Vlan 100 no ip address no shutdown DellEMC(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series and revised the output to display Native VLAN. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. The following describes the show vlan command shown in the following example. Column Heading Description (Column 1 — no heading) ● ● ● ● ● ● NUM Displays existing VLAN IDs. Status Displays the word Inactive for inactive VLANs and the word Active for active VLANs.
5 Active T Po20(Te 1/6) 6 Active U Po3(Te 1/4) 7 Active T Po20(Te 1/6) P 100 Active T Po1(Te 1/1) C 101 Inactive T Te 1/3 I 102 Inactive T Te 1/4 DellEMC# Example (VLAN ID) T Po20(Te 1/6) T Te 1/7 T Te 1/7 U Te 1/3 T Po20(Te 1/6) T Te 1/7 T Te 1/7 U Te 1/5 T Te 1/2 DellEMC# show vlan id 40 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 40 Status Description Q Ports Active M Te 1/47 DellEMC# show vlan id 4
222 Inactive DellEMC(conf-if-vl-222)# Example (OpenFlow instance) * O O O Related Commands NUM 1 3 6 8 12 Status Inactive Inactive Inactive Inactive Inactive U Te 1/22 Description Q Ports O Te 1/10 ● vlan-stack compatible — enable the Stackable VLAN feature on the selected VLAN. ● interface vlan — configure a VLAN. tagged Add a Layer 2 interface to a VLAN as a tagged interface. Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. When you use the no tagged command, the interface is automatically placed in the Default VLAN as an untagged interface unless the interface is a member of another VLAN. If the interface belongs to several VLANs, remove it from all VLANs to change it to an untagged interface.
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. When this command is configured, the VLAN is operationally UP if any of the interfaces specified in the track ip command are operationally UP, and the VLAN is operationally DOWN if none of the tracking interfaces are operationally UP.
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Untagged interfaces can only belong to one VLAN.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
Usage Information FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. Related Commands ● fefd reset — clear an interface in Err-disabled state. It doesn’t work until the interface is in errdisabled state. ● fefd mode — change FEFD mode on an interface. fefd interval Set an interval between control packets. Syntax fefd interval seconds To return to the default value, use the no fefd interval command.
Parameters Defaults normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol. aggressive (OPTIONAL) Enter the keyword aggressive to change the link state to “errordisabled” when a far-end failure the software detects on that interface.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. ● fefd-global — enable FEFD globally on the system. fefd-global Enable FEFD globally on the system. Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command.
Usage Information Related Commands If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. ● fefd — enable far-end failure detection. ● fefd-global interval — configure an interval between FEFD control packets. ● show fefd — display the FEFD command output. show fefd View FEFD status globally or on a specific interface.
Field Description State Displays the state of the interface and can be one of the following: ● bi-directional (interface is up, connected and hearing neighbor’s echoes). ● err-disabled (only found when FEFD mode is aggressive and when the interface has not hearing its neighbor’s echoes for three times the message interval. To reset an interface in this state, use the fefd reset command.) ● unknown (only found when FEFD mode is normal.
32 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor.
Defaults systemdescription Enter the keywords system-description to advertise the system description TLVs to the LLDP peer. system-name Enter the keywords system-name to advertise the system name TLVs to the LLDP peer. None Command Modes CONFIGURATION (conf-lldp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the Z9000 and S4810. 8.3.19.0 Introduced on the S4820T. clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface.
clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Syntax Parameters clear lldp neighbors [interface interface] interface interface Defaults (OPTIONAL)Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
Parameters interface interface Defaults Enter the following keywords and slot/port[/subport] or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. all Enter the keyword all to display information on all interfaces. events Enter the keyword events to display major events such as timer events.
Dec 4 22:38:27 : 88 cc 02 07 04 00 a0 c9 00 00 01 04 02 05 54 Dec 4 22:38:27 : 02 01 2c fe 05 aa bb cc 04 61 fa 01 40 00 00 Dec 4 22:38:28 : 00 00 00 00 00 00 00 00 c6 0f ba 27 Dec 4 22:38:28 : TLV: Chassis ID, Len: 7, Subtype: Mac address Value: 00:a0:c9:00:00:01 Dec 4 22:38:29 : TLV: Port ID, Len: 2, Subtype: Interface name Value: T Dec 4 22:38:29 : TLV: TTL, Len: 2, Value: 300 Dec 4 22:38:29 : TLV: UNKNOWN TLV, ORG_SPEC[aa-bb-cc, 4], Len: Value:a Dec 4 22:38:29 : aa bb cc 04 61 Dec 4 22:38:29 : 40 Dec 4
hello Configure the rate at which the LLDP control packets are sent to its peer. Syntax hello seconds To revert to the default, use the no hello seconds command. Parameters Defaults seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds. 30 seconds Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000 and S4810. To enable LLDP on the management interface, use the no disable command in LLDP-MANAGEMENTINTERFACE mode (conf-lldp-mgmtIf). mode To receive or transmit, set LLDP. Syntax mode {tx | rx} To return to the default, use the no mode command.
multiplier Set the multiple of the hello timer before LLDP declares the interface dead. Syntax multiplier number To return to the default, use the no multiplier command. Parameters Defaults integer Enter the number of consecutive misses before the LLDP declares the interface dead. The range is from 2 to 10. 4 Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Before LLDP can be configured on an interface, it must be enabled globally from CONFIGURATION mode. This command places you in LLDP mode on the interface; it does not enable the protocol.
Usage Information Example Example (Detail) Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval.
( 38, 4) ( 48, 4) ( 58, 4) ( 68, 4) ( 78, 4) ( 88, 4) ( 98, 4) (108, 4) (118, ( 39, 4) ( 40, 4) ( 41, 4) ( 42, 4) ( 43, 4) ( 44, 4) ( 45, 4) ( 46, 4) ( 47, 4) ( 49, 4) ( 50, 4) ( 51, 4) ( 52, 4) ( 53, 4) ( 54, 4) ( 55, 4) ( 56, 4) ( 57, 4) ( 59, 4) ( 60, 4) ( 61, 4) ( 62, 4) ( 63, 4) ( 64, 4) ( 65, 4) ( 66, 4) ( 67, 4) ( 69, 4) ( 70, 4) ( 71, 4) ( 72, 4) ( 73, 4) ( 74, 4) ( 75, 4) ( 76, 4) ( 77, 4) ( 79, 4) ( 80, 4) ( 81, 4) ( 82, 4) ( 83, 4) ( 8
Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet 1/1 Locally assigned remote Neighbor Index: 1 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-6
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S8420T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information. The Organizational Unique Identifier (OUI) for the Telecommunications Industry Association (TIA) is 00-12-BB. ● LLDP-MED Endpoint Device — any device that is on an IEEE 802 LAN network edge, can communicate using IP, and uses the LLDP-MED framework.
Related Commands Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● protocol lldp (Configuration) — enable LLDP globally. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med guest-voice-signaling To advertise a separate limited voice service for a guest user when the guest voice control packets use a separate network policy than the voice data, configure the system.
Related Commands ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system. Syntax advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} To return to the default, use the no advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} command.
Related Commands ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med power-via-mdi To advertise the Extended Power via MDI TLV, configure the system. Syntax advertise med power-via-mdi To return to the default, use the no advertise med power-via-mdi command. Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific.
layer2_priority Enter the Layer 2 priority. The range is from 0 to 7. DSCP_value Enter the DSCP value. The range is from 0 to 63. priority-tagged Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. number Defaults Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Defaults Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — de bug LLDP. ● show lldp neighbors — display the LLDP neighbors.
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
33 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
command in Global configuration mode. This setting causes the multicast MAC address to be mapped to the cluster IP address for NLB mode of operation of the switch. Related Commands ● clear arp-cache — clear dynamic ARP entries from the ARP table. ● show arp — display the ARP table.
Example (Multicast) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for multicast MAC address on the MXL platform.
34 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the S4048–ON platform.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
Version Description 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters Defaults clear ip msdp statistic peer peer-address peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer.
debug ip msdp Turn on MSDP debugging. Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters Defaults event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.).
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.0 Introduced If a list is not specified, all SA messages received from the default peer are accepted. You can enter multiple default peer commands.
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters Defaults name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
Parameters interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
ip msdp redistribute Filter local PIM SA entries in the SA cache. SAs which the ACL denies time out and are not refreshed. Until they time out, they continue to reside in the MSDP SA cache. Syntax ip msdp redistribute [list acl-name] Parameters Defaults list acl-name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured.
Defaults peer-address Enter the peer address of the MSDP peer in a dotted decimal format (A.B.C.D.). access-list name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the E-Series.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
Parameters Defaults peer peer address Enter the keyword peer then the peer address in a dotted decimal format (A.B.C.D.). sa-cache Enter the keywords sa-cache to display the Source-Active cache. summary Enter the keyword summary to display an MSDP peer summary. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
00:07:17 DellEMC# Peer1 show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
00:00:13 225.1.2.17 10.1.1.3 00:00:13 225.1.2.18 10.1.1.4 00:00:13 225.1.2.19 10.1.1.3 1036 Multicast Source Discovery Protocol (MSDP) 110.1.1.1 13.1.1.2 Rpf-Fail 110.1.1.1 13.1.1.2 Rpf-Fail 110.1.1.1 13.1.1.
35 Multicast Listener Discovery Protocol Dell Networking OS Supports Multicast Listener Discovery (MLD) protocol. Multicast Listener Discovery (MLD) is a Layer 3 protocol that IPv6 routers use to learn of the multicast receivers that are directly connected to them and the groups in which the receivers are interested. Multicast routing protocols (like PIM) use the information learned from MLD to route multicast traffic to all interested receivers.
Joining a Multicast Group The Querier periodically sends a General Query to the all-nodes multicast address FF02::1. A host that wants to join a multicast group responds to the general query with a report that contains the group address; the report is also addressed to the group (in the IPv6 Destination Address field). To avoid duplicate reporting, any host that hears a report from another host for the same group in which it itself is interested cancels its report for that group.
| | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +. -+ . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Version 2 multicast listener reports are sent by IP nodes to report (to neighboring routers) the current multicast listening state, or changes in the multicast listening state, of their interfaces.
| | * Source Address [1] * | | * * | | +-+ | | * * | | * Source Address [2] * | | * * | | +-+ . . . . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Auxiliary Data . . .
To adjust the query response time, use the following command: INTERFACE Mode ipv6 mld query-max-resp-time Clearing MLD groups Clear a specific group or all groups on an interface from the multicast routing table. To clear MLD groups, use the following command: EXEC Privilege clear ipv6 mld groups Debugging MLD Display Dell Networking OS messages about the MLD process.
show ipv6 mld groups Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 Displaying MLD Interfaces Display MLD interfaces.
● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. group-address Defaults (OPTIONAL) Enter the group address in the following format: x:x:x:x::x. The :: notation specifies successive hexadecimal fields of zero. None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping enable Enable MLD snooping on the switch globally. Syntax ipv6 mld snooping enable To disable MLD snooping, use the no ipv6 mld snooping enable command.
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. detail Defaults View detailed group information. None. Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific.
Current MLD snooping version is 1 MLD snooping is enabled on this interface MLD snooping querier is disabled and is currently inactive MLD snooping last member query response interval is 1000 ms MLD snooping explicit tracking is disabled show ipv6 mld snooping mrouter Display information on the MLD snooping router. Syntax Parameters Defaults show ipv6 mld snooping mrouter [vlan] VLAN (OPTIONAL) Enter the keyword VLAN then the VLAN number to display the information on that specific VLAN.
36 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● protocol spanning-tree mstp — enter MULTIPLE SPANNING TREE mode.
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● max-age — change the wait time before MSTP refreshes protocol configuration information. ● hello-time — change the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs).
Related Commands ● forward-delay — amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. ● max-age — change the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command.
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
name The name you assign to the multiple spanning tree region. Syntax name region-name To remove the region name, use the no name command. Parameters Defaults region-name Enter the MST region name. The range is 32 character limit. No default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Command Modes SPANNING TREE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.
Usage Information Version Description pre-6.2.1.1 Introduced on the E-Series. MSTP is not enabled when you enter MULTIPLE SPANNING TREE mode. To enable MSTP globally on the switch, enter the no disable command while in MULTIPLE SPANNING TREE mode. For more information about the multiple spanning tree protocol, refer to the Dell EMC Networking OS Configuration Guide.
Usage Information For two MSTP switches to be within the same MST region, the switches must share the same revision number. Related Commands ● msti — map the VLAN(s) to an MST instance. ● name — assign the region name to the MST region. show config View the current configuration for the mode. Only non-default values are shown. Syntax show config Command Modes MULTIPLE SPANNING TREE Command History Example This guide is platform-specific.
show spanning-tree mst configuration View the multiple spanning tree configuration. Syntax show spanning-tree mst configuration Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
brief (Optional) Enter the keyword brief to view a synopsis of the MST instance. guard (Optional) Enter the keyword guard to display the type of guard enabled on an MSTP interface and the current port state. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
The port is not in the portfast mode Port 89 (TenGigabitEthernet 2/7) is alternate Discarding Port path cost 0, Port priority 128, Port Identifier 128.89 Designated root has priority 16384, address 0001.e800.0a:5c Designated bridge has priority 16384, address 0001.e800.0a:5c Designated port id is 128.
Example (Guard) DellEMC# show spanning-tree msti 5 guard Interface Name Instance Sts Guard type -----------------------------------Te 1/1 5 INCON(Root) Rootguard Te 1/2 5 FWD Loopguard Te 1/3 5 EDS(Shut) Bpduguard spanning-tree Enable the multiple spanning tree protocol on the interface. Syntax spanning-tree To disable the multiple spanning tree protocol on the interface, use the no spanning-tree command.
spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface. Syntax spanning-tree msti instance {cost cost | priority priority} Parameters msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value. The range is from 1 to 200000.
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
37 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system.
Version Description E-Series legacy command Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
|Hop| OIF IP |Proto| Forwarding Code |Source Network/Mask| ----------------------------------------------------------------0 1.1.1.1 --> Destination -1 1.1.1.1 PIM Reached RP/Core 103.103.103.0/24 -2 101.101.101.102 PIM 103.103.103.0/24 -3 2.2.2.1 PIM 103.103.103.0/24 -4 103.103.103.3 --> Source -----------------------------------------------------------------The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic.
Version Description E-Series legacy command Example DellEMC# show ip multicast-cam stack-unit 1 port 0 Vrf Id Group Address Source Address Vlan Id L3 Ports ----------------------------------------------------0 224.1.1.1 0.0.0.0 1000 gi 1/10, 0 224.1.1.2 0.0.0.0 1000 gi 1/10, 0 224.1.1.1 165.13.34.5 2000 gi 1/11, IPMC index ------------ L2 Ports ------------ 1 gi 1/3, 1 gi 1/3, 2 gi 1/5, show ip mroute View the multicast routing table.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.
Vlan 20 (S) Vlan 30 (50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810.
Related Commands Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON. ● show ip pim tib — show the PIM tree information base. ipv6 multicast-routing Enables IPv6 multicast forwarding. Syntax ipv6 multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled.
the keyword count to display the total number of multicast routes with the spanned IIF. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON. Dell# show ipv6 multicast-cam stack-unit 1 port-set 0 Group Address : ff0e::228:1:1 Source Address : 400::2 VRF : 1 VlanId : 4095 IPMC : 609 L2 Ports : L3 Ports : gi 1/10 show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
38 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383.
show ipv6 neighbors Display IPv6 discovery information. Entering the command without options shows all IPv6 neighbor addresses stored on the control processor (CP). Syntax show ipv6 neighbors [vrf vrf-name] [ipv6-address| interface interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
Example DellEMC# show ipv6 neighbors IPv6 Address Expires(min) Hardware Address State Interface VLAN CPU -------------------------------------------------------------------100::1 0.03 00:00:00:00:00:22 DELAY Te 1/12 CP fe80::200:ff:fe00:22 232 00:00:00:00:00:22 STALE Te 1/12 CP 500::1 0.60 00:01:e8:17:5c:af REACH Te 1/13 CP fe80::200:ff:fe00:17 232 00:00:00:00:00:29 REACH Te 1/14 CP 900::1 0.60 00:01:e8:17:5c:b1 STALE Po 23 CP 400::1 0.
Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command.
To reset the hop count limit, use the no hop-limit {maximum | minimum limit} command. Parameters Defaults maximum limit Enter the keyword maximum then the hop limit value. The range is from 0 to 254. minimum limit Enter the keyword minimum then the hop limit value. The range is from 0 to 254. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● show ipv6 nd ra-guard policy — display the configuration applied on all the RA guard policies or a specific RA guard policy.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
● ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. match ra Enable verifying either of the configured source IPv6 address or prefix address or the source MAC address in the inspected messages. If this command is not configured, the verification process is bypassed.
Parameters Defaults value Enter the maximum transmission unit value in bytes. The range is from 1,280 to 11,982 bytes. 0 Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands.
retrans-time Enable the verification of the configured retransmission timer value in the received RA packets. Syntax retrans—timer value To reset the advertised retransmission interval, use the no retrans-timervalue command. Parameters Defaults value Enter the advertised retransmission time interval in milliseconds. The range is from 100 to 4,294,967,295 milliseconds. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands.
show config Display the RA guard policy mode configurations. Syntax show config Command Modes POLICY LIST CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
show ipv6 nd ra–guard policy Display the configurations applied on all the RA guard policies or a specific RA guard policy. Syntax show ipv6 nd ra-guard policy policy-name Parameter policy policy- name Enter the keyword policy then the policy name. The policy name allows a maximum of 140 characters. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
● ipv6 nd raguard attach-policy — apply the IPv6 RA guard to a specific interface. trusted–port Allow bypassing the configured RA guard validation and forwards the RA packets received on the interface, which has the trusted port policy attached. Syntax trusted-port To reset the policy applied to the trusted port, use the no trusted-port command. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
39 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface TenGigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
If the timer expires and an object’s state has changed, a notification is sent to the client. If no delay is configured, a notification is sent immediately after a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds. Related Commands ● track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface.
Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object. Syntax show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500.
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP. DellEMC# show track Track 1 IP route 23.0.0.
To return to the default setting, use the no threshold metric {up number | down number} command. Parameters Defaults up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold. down number Enter a number for the DOWN threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default DOWN threshold is255.
track interface ip routing Configure object tracking on the routing status of an IPv4 Layer 3 interface. Syntax track object-id interface interface ip routing To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
track interface line-protocol Configure object tracking on the line-protocol state of a Layer 2 interface. Syntax track object-id interface interface line-protocol To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefix-len Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32. vrf vrf-name (Optional) You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs.
Usage Information Use this command to create an object that tracks the UP and/or DOWN threshold of an IPv4 route metric. In order for a route’s metric to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv4 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table.
Usage Information To disable the attempt to track the reachability of next-hop after the configured refresh interval, set the refresh interval as 0. Related Commands ● show track – display information about tracked objects, including configuration, current state, and clients which track the object. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric.
● The resolution value used to map RIP routes is not configurable. The RIP hop-count is automatically multiplied by 16 to scale it. For example, a RIP metric of 16 (unreachable) scales to 256, which considers the route to be DOWN. Related Commands ● threshold metric – configure the metric threshold used to determine the UP and/or DOWN state of a tracked route. ● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric.
Output Description Interface type Displays the interface type and slot/port number or address of the IPv4/IPv6 route slot/port , IP that is being tracked. route ip-address , IPv6 route ipv6- address object is Up/ Down Up/Down state of tracked object; for example, IPv4 interface, reachability or metric threshold of an IP route. number changes, Number of times that the state of the tracked object has changed and the time last change time since the last change in hours:minutes:seconds.
track interface ipv6 routing Configure object tracking on the routing status of an IPv6 Layer 3 interface. Syntax track object-id interface interface ipv6 routing To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
track ipv6 route metric threshold Configure object tracking on the threshold of an IPv4 route metric. Syntax track object-id ipv6 route ipv6-address/prefix-len metric threshold To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. ipv6-address/ prefix-len Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128.
● threshold metric – configure the metric threshold used to determine the UP and/or DOWN state of a tracked route. ● track resolution ipv6 route – configure the protocol-specific resolution value used to scale an IPv6 route metric. track ipv6 route reachability Configure object tracking on the reachability of an IPv6 route. Syntax track object-id ipv6 route ip-address/prefix-len reachability To return to the default setting, use the no track object-id command.
track resolution ipv6 route Configure the protocol-specific resolution value used to scale an IPv6 route metric. Syntax track resolution ipv6 route {isis resolution-value | ospf resolution-value} To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. Use the range to 1 to 500. isis resolution- value Enter the resolution used to convert the metric in the routing table for ISIS routes to a scaled metric.
40 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Version Description 9.13(0.0) Introduced on the remaining DNOS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. debug ip ospf Display debug information on OSPF.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.4(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the database-timer rate-limit option for the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Field Description ● N + (N-bit is set) ● N - (N-bit is not set) ● MC+ (bit used by MOSPF is set and router is able to forward IP multicast packets) ● MC- (bit used by MOSPF is not set and router cannot forward IP multicast packets) ● E + (router is able to accept AS External LSAs) ● E - (router cannot accept AS External LSAs) ● T + (router can support TOS) ● T - (router cannot support TOS) Example hi: Displays the amount of time configured for the HELLO interval.
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
Related Commands Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ● show ip ospf asbr — display the VLAN configuration. distance Define an administrative distance for particular routes to a specific IP address.
Version Description 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. distance ospf Configure an OSPF distance metric for different types of routes. S4048–ON Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255.
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. To specify a distance for routes learned from other routing domains, use the redistribute command. distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table. S4048–ON Syntax distribute-list prefix-list-name in [interface] To delete a filter, use the no distribute-list prefix-list-name in [interface] command.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. S4048–ON Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on all platforms. The higher this parameter is set, the faster OSPF converge takes place. NOTE: The faster the convergence, the more frequent the route calculations and updates. This behavior impacts CPU utilization and may impact adjacency stability in larger topologies. Generally, convergence level 1 meets most convergence requirements.
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The Helper mode is enabled by default on the device. To enable the restart mode also on the device, you must configure the grace period using this command. After you enable restart mode the router advertises the neighbor as fully adjacent during a restart. graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart.
graceful-restart mode Enable the graceful restart mode. S4048–ON Syntax graceful-restart mode [planned-only | unplanned-only] To disable graceful restart mode, use the no graceful-restart mode command. Parameters Defaults planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only.
Parameters Defaults role helper-only (OPTIONAL) Enter the keywords helper-only to specify the OSPF router is a helper only during graceful restart. role restart-only (OPTIONAL) Enter the keywords restart-only to specify the OSPF router is a restart only during graceful-restart. By default, OSPF routers are both helper and restart routers during a graceful restart. Command Modes ROUTER OSPF Command History This guide is platform-specific.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. All neighboring routers in the same network must use the same password to exchange OSPF information.
Usage Information Related Commands Version Description pre- 6.1.1.1 Introduced on the E-Series. If this command is not configured, cost is based on the auto-cost command. When you configure OSPF over multiple vendors, to ensure that all routers use the same cost, use the ip ospf cost command. Otherwise, OSPF routes improperly. ● auto-cost — control how the OSPF interface cost is calculated. ip ospf dead-interval Set the time interval since the last hello-packet was received from a router.
Related Commands ● ip ospf hello-interval — set the time interval between the hello packets. ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. S4048–ON Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters Defaults seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds.
ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. S4048–ON Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command. Parameters Defaults keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. No MD5 authentication is configured.
ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets. S4048–ON Syntax ip ospf mtu-ignore To return to the default, use the no ip ospf mtu-ignore command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Set the time interval to a number large enough to prevent unnecessary retransmissions. ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. S4048–ON Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific.
maximum-paths Enable the software to forward packets over multiple paths. S4048–ON Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths.
To disable an OSPF area, use the no network ip-address mask area area-id command. Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format. (/x) area-id Enter the OSPF area ID as either a decimal value or in a valid IP address. Decimal value range is from 0 to 65535. IP address format is dotted decimal format A.B.C.D.
passive-interface Suppress both receiving and sending routing updates on an interface. S4048–ON Syntax passive-interface {default | interface} To enable both the receiving and sending routing, use the no passive-interface interface command. To return all OSPF interfaces (current and future) to active, use the no passive-interface default command. Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive.
The default keyword sets all interfaces as passive. You can then configure individual interfaces, where adjacencies are desired, using the no passive-interface interface command. The no form of this command is inserted into the configuration for individual interfaces when the no passiveinterface interface command is issued while passive-interface default is configured.
● 1 = OSPF External type 1 ● 2 = OSPF External type 2 route-map map- name tag tag-value Defaults (OPTIONAL) Enter the keywords route-map then the name of the route map. (OPTIONAL) Enter the keyword tag then a number. The range is from 0 to 4294967295. Not configured. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
Parameters as number Enter the autonomous system number. The range is from 1 to 65535. metric metric- value (OPTIONAL) Enter the keyword metric then the metric-value number. The range is from 0 to16777214. metric-type (OPTIONAL) Enter the keywords metric-type then one of the following: type-value route-map map- name tag tag-value Defaults ● 1 = for OSPF External type 1 ● 2 = for OSPF External type 2 (OPTIONAL) Enter the keywords route-map then the name of the route map.
Parameters tag (OPTIONAL) Enter the name of the IS-IS routing process. level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- value (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
Parameters Defaults ip-address Enter the router ID in the IP address format. None. Command Modes ROUTER OSPF Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Parameters Defaults process-id Enter a number for the OSPF instance. The range is from 1 to 65535. vrf name (Optional) Enter the VRF process identifier to tie the OSPF instance to the VRF. All network commands under this OSPF instance are then tied to the VRF instance. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.
show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. S4048–ON Syntax Parameters Defaults show ip ospf [process-id | vrf vrf-name] asbr process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
RouterID 3.3.3.3 1.1.1.1 DellEMC# Flags -/-/-/ E/-/-/ Cost Nexthop 2 10.0.0.2 0 0.0.0.0 Interface Area Te 1/1 1 0 show ip ospf database Display all LSA information. If you do not enable OSPF on the switch, no output is generated. S4048–ON Syntax show ip ospf process-id [vrf vrf-name] database [database-summary] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
Example Field Description Link ID Identifies the router ID. ADV Router Identifies the advertising router’s ID. Age Displays the link state age. Seq# Identifies the link state sequence number. This number allows you to identify old or duplicate link state advertisements. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. DellEMC> show ip ospf 1 database OSPF Router with ID (11.1.2.
● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Example Field Description Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. DellEMC# show ip ospf 100 database asbr-summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Asbr (Area 0.0.0.
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Example Field Description Network Mask Displays the network mask implemented on the area. Metrics Type Displays the external type. TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router.
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: ● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.
Example Field Description LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Length Displays the Fletcher checksum of an LSA’s complete contents. Network Mask Displays the length in bytes of the LSA. Attached Router Identifies the IP address of routers attached to the network.
vrf vrf-name Enter the keyword vrf followeed by the name of the VRF to view NSSA-External LSA information corresponding to the OSPF process that is tied to a specific VRF. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: ● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view opaque-area LSA information corresponding to the OSPF process that is tied to a specific VRF. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
Item Description ● DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. ● E or No E is displayed on whether the originating router can accept AS External LSAs. Example LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the advertising router’s ID. Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA.
adv-router ip- address (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
adv-router ip- address (OPTIONAL) Enter the keywords adv-router then the IP address of an Advertising Router to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
● the default destination (0.0.0.0) for Type 5 LSAs adv-router ip- address (OPTIONAL) Enter the keywords adv-router followed by the IP address of an Advertising Router to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Example Item Description LS Seq Number Displays the link state sequence number. This number detects duplicate or old LSAs. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Length Displays the length in bytes of the LSA. Number of Links Displays the number of active links to the type of router (Area Border Router or AS Boundary Router) listed in the previous line. Link connected to: Identifies the type of network to which the router is connected.
Link connected to: a Stub Network (Link ID) Network/subnet number: 11.1.5.0 --More-Related Commands ● show ip ospf database — display OSPF database information. show ip ospf database summary Display the network summary (type 3) LSA routing information. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database summary [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database summary command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router.
TOS: 0 Metric: 1 LS age: 7 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.33.0 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000016 Checksum: 0x1241 Length: 28 Network Mask: /26 TOS: 0 Metric: 1 DellEMC# Related Commands ● show ip ospf database — display OSPF database information. show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
Transmit Delay is 1 sec, State DROTHER, Priority 1 Designated Router (ID) 192.168.253.5, Interface address 192.168.0.4 Backup Designated Router (ID) 192.168.253.3, Interface address 192.168.0.2 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Neighbor Count is 3, Adjacent neighbor count is 2 Adjacent with neighbor 192.168.253.5 (Designated Router) Adjacent with neighbor 192.168.253.
Usage Information Example Version Description pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id neighbor command shown in the following example. Item Description Neighbor ID Displays the neighbor router ID. Pri Displays the priority assigned neighbor. State Displays the OSPF state of the neighbor. Dead Time Displays the expected time until the Dell OS declares the neighbor dead. Address Displays the IP address of the neighbor.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
global Enter the keyword global to display the packet counts received on all running OSPF interfaces and packet counts OSPF neighbors receive and transmit. interface name (OPTIONAL) Enter the keyword interface then one of the following interface keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
Row Heading Description Hello Number of OSPF Hello packets. DDiscr Number of database description packets. LSReq Number of link state request packets. LSUpd Number of link state update packets. LSAck Number of link state acknowledgement packets. TxQ-Len The transmission queue length. RxQ-Len The reception queue length. Tx-Mark The highest number mark in the transmission queue. Rx-Mark The highest number mark in the reception queue.
OSPF Global Queue Length TxQ-Len RxQ-Len Hello-Q 0 0 LSR-Q 0 0 Other-Q 0 0 Tx-Mark 0 0 0 Rx-Mark 2 0 0 Error packets (Only for RX) Intf-Down Wrong-Len Auth-Err Version No-Buffer Q-OverFlow 0 0 0 0 0 0 Non-Dr Invld-Nbr MD5-Err AreaMis Seq-No Unkown-Pkt 0 0 0 0 0 0 Self-Org 0 Nbr-State 0 Chksum 0 Conf-Issues 0 Socket 0 Error packets (Only for TX) Socket Errors DellEMC# Usage Information The show ip ospf process-id statistics command displays the error packet count received on each interface as: ● ● ●
Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Command Modes ROUTER OSPFv2 Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced the keyword msec. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
max-interval Defaults Set the maximum amount of time the system waits before sending the LSA. The range is from 1 to 600,000 milliseconds. ● start-interval: 0 msec ● hold-interval: 5000 msec ● max-interval: 5000 msec Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes ROUTER OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
esp encryptionalgorithm Encryption algorithm used with ESP. Valid values are: 3DES, DES, AES-CBC, and NULL. For AES-CBC, only the AES-128 and AES-192 ciphers are supported. key-encryptionalgorithm key (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in encryption.
When you configure encryption for an OSPFv3 area with the area encryption command, you enable both IPsec encryption and authentication. However, when you enable authentication on an area with the area authentication command, you do not enable encryption at the same time. If you have enabled IPsec authentication in an OSPFv3 area with the area authentication command, you cannot use the area encryption command in the area at the same time.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. area range Summarize routes matching an address or mask at an area border router (ABR). Syntax area area-id range ip-address mask [not-advertise] To disable route summarization, use the no area area-id range ip-address mask command.
Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.9(0.
Version Description 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. debug ipv6 ospf bfd Display debug information and interface types for bidirectional forwarding detection (BFD) on OSPF IPv6 packets.
Example Lines Beginning With or Including Description Sending Ver:3 Sending OSPF3 version..
Example Example (detail) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.
Lines Beginning With or Including Description ● 5 - link state acknowledgement Length: Displays the OSPFv3 packet length. Router ID: Displays the OSPFv3 router ID. Area ID: Displays the OSPFv3 area ID. Chksum: Displays the OSPFv3 checksum. debug ipv6 ospf packet Display debug information and interface types on OSPF IPv6 packets.
Example Example (detail) Version Description 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on E-Series. DellEMC# debug ipv6 ospf packet OSPFv3 packet related debugging is on for all interfaces 05:21:01 : OSPFv3: Sending, Ver:3, Type:1(Hello), Len:40, Router ID:223.255.255.254, Area ID:0, Inst:0, on Po 255 05:21:03 : OSPFv3: Received, Ver:3, Type:1(Hello), Len:40, Router ID:223.255.255.
Parameters interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
default-information originate Configure the Dell EMC Networking OS to generate a default external route into an OSPFv3 routing domain. Syntax default-information originate [always] [metric metric-value] [metric-type type-value] [route-map map-name] To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to specify that default route information must always be advertised.
Parameters Defaults seconds Time duration, in seconds, that specifies the duration of the restart process before OSPFv3 terminates the process. The range is from 40 to 1800 seconds. OSPFv3 graceful restart is disabled and functions in a helper-only role. Command Modes ROUTER OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.4.1.0 Introduced on the E-Series and C-Series. ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface.
Usage Information Version Description 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Before you enable IPsec authentication on an OSPFv3 interface, first enable IPv6 unicast routing globally, configure an IPv6 address and enable OSPFv3 on the interface, and assign the interface to an area. An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router.
Usage Information Version Description 9.2.0.0 Introduced on the Z9000, S4820T, and S4810. This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode.
ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down. Syntax ipv6 ospf dead-interval seconds To return to the default time interval, use the no ipv6 ospf dead-interval command. Parameters Defaults seconds Enter the time interval in seconds. The range is from 1 to 65535 seconds. 40 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific.
For AES-CBC, only the AES-128 and AES-192 ciphers are supported. key-encryptiontype key (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication. The required lengths of a non-encrypted or encrypted key are: 3DES - 48 or 96 hex digits; DES - 16 or 32 hex digits; AES-CBC -32 or 64 hex digits for AES-128 and 48 or 96 hex digits for AES-192.
ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
Version Description 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths.
passive-interface Disable (suppress) sending routing updates on an interface. Syntax passive—interface interface To enable sending routing updates on an interface, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
redistribute Redistribute into OSPFv3. Syntax redistribute {bgp as number}{connected | static}[metric metric-value | metric-type type-value] [route-map map-name] [tag tag-value] To disable redistribution, use the no redistribute {connected | static} command. Parameters bgp as number Enter the keyword bgp then the autonomous system number. The range is from 1 to 65535. connected Enter the keyword connected to redistribute routes from physically connected interfaces.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. To redistribute the default route (x:x:x:x::x), use the default-information originate command. router-id Designate a fixed router ID. Syntax router-id ip-address To return to the previous router ID, use the no router-id ip-address command. Parameters Defaults ip-address Enter the router ID in the dotted decimal format.
show crypto ipsec policy Display the configuration of IPsec authentication and encryption policies. Syntax Parameters Defaults show crypto ipsec policy [name name] name name (OPTIONAL) Displays configuration details about a specified policy. No default behavior or values. Command Modes EXEC EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Inbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Outbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Transform set : esp-128-aes esp-sha1-hm
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults No default behavior or values. Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy
external (OPTIONAL): Enter the keyword external to display the external link states. grace-lsa (OPTIONAL): Enter the keyword grace-lsa to display the Type-11 Grace LSAs sent and received on an OSPFv3 router. inter-area-prefix (OPTIONAL): Enter the keyword inter-area-prefix to display the inter area prefix link states. inter-area-router (OPTIONAL): Enter the keyword inter-area-router to display the inter area router link states.
LS Age : 10 Link State ID : 6.16.192.66 Advertising Router : 100.1.1.1 LS Seq Number : 0x80000001 Checksum : 0x1DF1 Length : 36 Associated Interface : Te 1/3 Restart Interval : 180 Restart Reason : Switch to Redundant Processor Example (databasesummary) DellEMC# show ipv6 ospf 3 database database-summary OSPFv3 Router with ID (1.1.1.
LS Type: OSPFv3 AS external LSA Link State ID: 0.0.0.1 Advertising Router: 10.130.254.101 LS Seq Number: 0x80000001 Checksum: 0xF038 Length: 36 Prefix: 9001::/64 Prefix Options: 0x10 ( DN ) Metric Type: 2 Metric: 20 Example (nssaexternal) DellEMC#show ipv6 ospf 10 database nssa-external OSPFv3 Router with ID (1.1.1.1) (Process ID 10) AS External Link States (Area 1) LS Age: 35 LS Type: OSPFv3 NSSA LSA Link State ID: 0.0.0.1 Advertising Router: 1.1.1.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Added support for showing BFD status on the S4820T, S4810, and Z9000. 9.1.(0.
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults None Command Modes EXEC EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Defaults holdtime Enter a number as the hold time. The range is from 0 to 2147483647. The default is 10 seconds. When configured in milli seconds, 200 is the least value that is allowed to be configured. msec Enter the keyword msec to specify the time interval value in milli seconds. NOTE: If you do not specify the msec option, the timer values are considered as seconds.
41 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
Related Commands Version Description 7.7.1.0 Introduced on the E-Series. ● ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name test [l2–switch] To remove a redirect list from an interface, use the no ip redirect-group name command.
The Layer2 PBR option matches the layer2 traffic flow. If you un-configure this option, then the Layer2 traffic is not matched. You can apply the l2–switch option to redirect Layer2 traffic only on a VLAN interface. This VLAN interface must be configured with an IP address for ARP resolution. NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces. The Layer3 routing is not affected on the same interface on which Layer2 PBR is applied.
permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: ● If you know the filter sequence number, use the no seq sequence-number syntax command.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.
● ● ● ● ● ● = = = = = = acknowledgement finish (no more data from the user) push function reset the connection synchronize sequence number urgent field source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address.
seq Configure a filter with an assigned sequence number for the redirect list.
● lt= less than ● range = inclusive range of ports (you must specify two ports for the port command parameter.) source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule destination-port Enter the keywords destination-port then the port number to be matched in the ACL rule in the ICAP rule. source-portrange Enter the keywords Source-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
Command History Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
Example DellEMC# show ip redirect-list explicit_tunnel IP redirect-list explicit_tunnel: Defined as: seq 5 redirect tunnel 1 track 1 tcp 155.55.2.0/24 222.22.2.0/24, Track 1 [up], Next-hop reachable (via Te 1/32) seq 10 redirect tunnel 1 track 1 tcp any any, Track 1 [up], Next-hop reachable (via Te 1/32) seq 15 redirect tunnel 2 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Next-hop reachable (via Te 1/32) seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.
42 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface.
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Removed the in and out parameters. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
Example Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced DellEMC(conf)# ip access-list standard map1 DellEMC(config-std-nacl)# permit 224.0.0.
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command.
To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. access-list Defaults Enter the name of an extended access list. Maximum 16 characters. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
group-address group-address mask override Enter the keywords group-address then a group-address mask, in dotted decimal format (/xx), to assign that group address to the RP. Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable. NOTE: This option is applicable to multicast group range. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Removed the acl-access-list parameter. Modified the max value of S, G entry second range from 86400 to 65535. Introduced on the S6000ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.7(0.0) Added support for VRF. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
If the PIM DR flood is not disabled (default setting): ● Multicast traffic is transmitted on the egress port towards the PIM DR if the port is not the incoming interface. ● Multicast traffic for an unknown group is sent on the port towards the PIM DR. When DR flooding is disabled, multicast traffic for an unknown group is dropped. show ip pim bsr-router View information on the Bootstrap router.
Candidate BSR address: 7.7.7.7, priority: 0, hash mask length: 30 DellEMC# show ip pim interface View information on the interfaces with IP PIM enabled. S4048–ON Syntax show ip pim [vrf vrf-name] interface Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on this VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
Field Description Nbr Count Displays the number of PIM neighbors discovered over this interface. Query Intvl Displays the query interval for Router Query messages on that interface (configured with ip pim query-interval command). DR Prio Displays the Designated Router priority value configured on the interface (use the ip pim dr-priority command). DR Displays the IP address of the Designated Router for that interface.
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim neighbor command shown in the following example. Field Description Neighbor address Displays the IP address of the PIM neighbor. Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found.
Example Example (Mapping) Example (Address) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series.
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series. The following describes the show ip pim snooping neighbor commands shown in the following example. Field Description Neighbor address Displays the IP address of the neighbor learned through PIM-SM snooping. Interface Displays the VLAN ID number and slot/port on which the PIM-SM-enabled neighbor was discovered.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series. The following describes the show ip pim snooping tib commands shown in the following example. Field Description (S, G) Displays the entry in the PIM multicast snooping database.
SGR-P - (S,G,R) Prune Timers: Uptime/Expires * : Inherited port (165.87.1.7, 225.1.2.1), uptime 00:00:08, expires 00:02:52, flags: j Incoming interface: Vlan 2, RPF neighbor 0.0.0.0 Outgoing interface list: TenGigabitEthernet 2/11 Upstream Port -/TenGigabitEthernet 2/13 DR Port -/TenGigabitEthernet 2/20 RPF 165.87.32.10 00:00:08/00:02:52 show ip pim ssm-range Display the non-default groups added using the SSM range feature.
Example Group Address / MaskLen show ip pim summary View information about PIM-SM operation. S4048–ON Syntax show ip pim [vrf vrf-name] summary Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
TIB summary: 1/1 (*,G) entries in PIM-TIB/MFC 1/1 (S,G) entries in PIM-TIB/MFC 0/0 (S,G,Rpt) entries in PIM-TIB/MFC 0 0 0 0 PIM nexthops RPs sources Register states Message summary: 2582/2583 Joins sent/received 5/0 Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 State-Refresh messages sent/received 0/0 MSDP updates sent/received 0/0 Null Register messages sent/received 0/0 Register-stop messages sent/received Data path event summary: 0 no-cache messag
Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim tib command shown in the following example.
Vlan 2006 Forward/Sparse 00:06:21/Never (20.10.4.9, 225.1.1.1), uptime 00:06:21, expires 00:02:06, flags: CT Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (*, 225.1.1.2), uptime 00:40:15, expires 00:00:00, RP 20.40.4.4, flags: SCJ Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (20.10.4.9, 225.1.1.
clear ipv6 pim tib Clear the IPv6 PIM multicast-routing database (tree information base—TIB). Syntax clear ipv6 pim [vrf vrf-name] tib [group-address] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format.
Command Modes EXEC Privilege Command History Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. ipv6 pim bsr-border Define the border of IPv6 PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ipv6 pim bsr-border To return to the default value, use the no ipv6 pim bsr-border command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, S3048-ON, S3100 Series, S4048-ON, S4048T-ON, S6000-ON, S6010-ON, S6100-ON, Z9100-ON. ipv6 pim dr-priority Change the designated router (DR) priority for the IPv6 interface.
ipv6 pim rp-address Configure a static PIM rendezvous point (RP) address for a group. First-hop routers use this address to send register packets on behalf of the source multicast host. Syntax ipv6 pim [vrf vrf-name] rp-address address {group-address group-address mask} [override] To remove an RP address, use the no ipv6 pim re-address address group-address mask [override] command.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
ipv6 pim sparse-mode sg-expiry-timer Enable expiry timers globally for all sources. Syntax ipv6 pim [vrf vrf-name] sparse-mode sg-expiry-timer seconds To disable configured timers and return to default mode, use the no ipv6 pim sparse-mode sgexpiry-timer command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable expiry timer for all sources on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
Usage Information PIM leaf routers join the shortest path tree immediately after the first packet arrives from a new source. show ipv6 pim bsr-router View information on the bootstrap router. Syntax show ipv6 pim [vrf vrf-name] bsr-router Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
Example DellEMC#show ipv6 pim interface Interface Ver/ Nbr Query Mode Count Intvl Te 1/1 v2/S 1 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router DR Prio 101 Te 1/2 v2/S 1 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router 100 Te 1/3 v2/S 0 30 Address : fe80::4e76:25ff:fee5:32c2 DR : this router 1 show ipv6 pim neighbor Displays IPv6 PIM neighbor information.
group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format to view RP mappings for a specific group. NOTE: The :: notation specifies successive hexadecimal fields of zero. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
show ipv6 pim summary View information about PIM-SM operation. Syntax Parameters show ipv6 pim [vrf vrf-name] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
show ipv6 pim tib View the IPv6 PIM multicast-routing database (tree information base — tib). Syntax show ipv6 pim [vrf vrf-name] tib [group-address [source-address]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
43 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
monitor multicast-queue Configure monitor QoS multicast queue ID. Syntax monitor multicast-queue queue-id To remove the configuration, use the no monitor multicast-queue command. Parameters Defaults queue-id Enter the QoS multicast queue ID. The range is from 0 to 9. queue-id: 0 Enable status: Disabled Command Modes CONFIGURATION Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific.
Defaults set ip dscp Configures the Differentiated Services Code Point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default value, use the no form of this command. dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic.
rate-limit Configure the rate-limit to limit the mirrored packets. Syntax rate-limit limit To remove the limit, use the no rate-limit limit command. Parameters Defaults limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. 60 Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. ● For a port channel interface, enter the keywords port-channel then a number. range Enter the keyword range to specify the list of interfaces. any Enter the keyword any to specify all interfaces.
Example 1282 Version Description 9.4.0.0 Added support for Source and destination. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
44 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. S4048 Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. S4048 Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN.
private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input.
To remove PVLAN mode from the selected port, use the no switchport mode private-vlan command. Parameters Defaults host Enter the keyword host to configure the selected port or port channel as an isolated interface in a PVLAN. promiscuous Enter the keyword promiscuous to configure the selected port or port channel as an promiscuous interface. trunk Enter the keyword trunk to configure the selected port or port channel as a trunk port in a PVLAN. Disabled.
45 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the S4048 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S4048 Syntax disable To enable PVST+, use the no disable command.
Related Commands ● protocol spanning-tree pvst — enter PVST+ mode. extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S4048 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
-------------------------------------------------------Te 1/10 Desg 128.140 128 200000 FWD 0 P2P No Te 1/12 Dis 128.142 128 200000 DIS 0 P2P No DellEMC(conf-pvst)# Related Commands ● protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command.
Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands ● disable — disables PVST+. ● show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. S4048 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094.
Usage Information Example (Brief) Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. 6.2.1.1 Introduced.
The port is not in the Edge port mode Port 131 (TenGigabitEthernet 1/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.131 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
Related Commands ● spanning-tree pvst — configure PVST+ on an interface. spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
no ip address switchport spanning-tree pvst vlan 3 cost 1800 no shutdown DellEMC(conf-if-te-1/1)# end DellEMC# Related Commands ● show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN.
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. S4048 Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
bridge-priority value Defaults Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. 32768 Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Defaults 15 seconds Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Related Commands 1302 Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
46 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis.
When you set the priority for a port channel, the physical interfaces assigned to the port channel are configured with the same value. You cannot assign the dot1p-priority command to individual interfaces in a port channel. rate police Police the incoming traffic rate on the selected interface. Syntax Parameters Defaults rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] [vlan vlan-id] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
S-Series On one interface, you can configure the rate police command for a VLAN or you can configure the rate police command for an interface. rate-shape Shape the traffic output on the selected interface. Syntax rate shape [kbps] rate [burst-KB] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
Related Commands ● rate-shape — shapes traffic output as part of the designated policy. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. S4048–ON Syntax Parameters Defaults service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} queue Enter a value from 0 to 7.
service-class dynamic dot1p Honor all 802.1p markings on incoming switched traffic on an interface (from INTERFACE mode) or on all interfaces (from CONFIGURATION mode). A CONFIGURATION mode entry supersedes an INTERFACE mode entry. S4048–ON Syntax service-class dynamic dot1p To return to the default setting, use the no service-class dynamic dot1p command. Defaults All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command.
Usage Information Version Description 6.1.1.1 Introduced on the E-Series. To honor all incoming 802.1p markings on incoming switched traffic on the interface, enter this command. By default, this facility is not enabled (that is, the 802.1p markings on incoming traffic are not honored). You can apply this command on both physical interfaces and port channels.
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify data traffic into one of eight classes . Dell EMC Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-of-service policies to each class. Syntax Parameters Defaults class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
Related Commands ● ● ● ● ● ● ● ● ● ● ip access-list extended — configures an extended IP ACL. ip access-list standard — configures a standard IP ACL. match ip access-group — configures the match criteria based on the access control list (ACL). match ip precedence — identifies the IP precedence values as match criteria. match ip dscp — configures the match criteria based on the DSCP value. match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL.
Related Commands Version Description 6.1.1.1 Introduced on the E-Series. ● show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the policies (80 characters maximum).
match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IP-any class-maps on both ACLs as well as VLANs.
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed. Related Commands ● class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria.
Usage Information Version Description 7.7.1.0 Added the keyword multicast ; added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series; added support for the DSCP Marking option. 6.2.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive.
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. To access this command, enter the class-map command.
match mac access-group Configure a match criterion for a class map, based on the contents of the designated MAC ACL. Syntax Parameters Defaults [seq sequence number] match mac access-group {mac-acl-name} mac-acl-name Enter a MAC ACL name. Its contents is used as the match criteria in the class map. none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information An aggregate output QoS policy applies to all outbound port traffic.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to add support for Layer 2. 6.1.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rateshape, scheduler strict, bandwidth-percentage, and WRED can be defined.
Usage Information Version Description 7.4.1.0 and 6.5.3.0 Introduced on the E-Series. This command does not uniquely identify a queue, but rather identifies only a set of queues. The WRED curve is applied to all eight egress Multicast queues. Important Points to Remember — Multicast-Bandwidth Option ● A unique multicast weighted fair queuing (WFQ) setting can be applied only on a per port-pipe basis.
Usage Information Version Description 7.4.1.0 and 6.5.3.0 Introduced on the E-Series. This command does not uniquely identify a queue, but rather identifies only a set of queues. The WRED Curve is applied to all eight ingress Multicast queues. NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information The default burst size is 100Kb. If a different value is required, you must configure the burst size to the required value. Related Commands ● rate police — specifies traffic policing on the selected interface. ● qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy.
Version Description 6.1.1.1 Introduced on the E-Series. Usage Information On 40-port 10G stack-unit if the traffic is shaped between 64 and 1000 Kbs, for some values, the shaped rate is much less than the value configured.You must configure the peak rate and peak burst size using the same value: kilobits or packets per second. Similarly, you must configure the committed rate and committed burst size with the same measurement.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series. You can attach a single policy-map to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information A single policy-map can be attached to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. Related Commands ● policy-map-output — creates an output policy map.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information There are eight queues per interface on the S6000 and four queues on the S-Series. This command assigns a class map or QoS policy to different queues.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added mac-dot1p on the C-Series and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added support for mac-dot1p. 6.1.1.1 Introduced on the E-Series. After the IP DSCP bit is set, other QoS services can then operate on the bit settings. show qos class-map View the current class map information.
Example DellEMC# show qos class-map Class-map match-any CM seq 5 Match ip access-group ACL DellEMC# Related Commands ● class-map — identifies the class map. show qos dot1p-queue-mapping Displays the dot1p priority to queue mapping on the switch. Syntax show qos dot1p-queue-mapping Defaults ● Dot1p Priority : 0 1 2 3 4 5 6 7 ● Queue : 0 0 0 1 2 3 3 3 Command Modes EXEC Privilege Command History This guide is platform-specific.
9.8(0.0P2) Introduced on the S3048-ON. summary To view a policy map interface summary, enter the keyword summary and optionally one of the following keywords and slot/port or number information: interface ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
3 DellEMC# Example (IPv6) CM3 q3 DellEMC# show qos policy-map detail Tengigabitethernet 1/1 Interface TeGigabitEthernet 4/1 Policy-map-input pmap1 Queue# Class-map-name Qos-policy-name 0 c0 q0 1 c1 q1 2 c2 q2 3 c3 q3 DellEMC# Example (Summary IPv4) DellEMC#sho qos policy-map summary Interface policy-map-input policy-map-output Te 4/1 PM1 Te 4/2 PM2 PMOut DellEMC# show qos policy-map-input View the input QoS policy map details.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added Trust IPv6 diffserv. 6.1.1.1 Introduced on the E-Series.
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. DellEMC# show qos qos-policy-output Qos-policy-output qosOut Rate-limit 50 50 peak 50 50 Wred yellow 1 Wred green 1 DellEMC# show qos statistics View QoS statistics.
Version Description 9.12(0.0) Modified to display the global WRED state. 9.11(0.0) Updated the show qos statistics egress—queue output to reflect per queue per port tx and drop rates. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
show qos wred-profile View the WRED profile details. Syntax Parameters Defaults show qos wred-profile wred-profile-name wred-profilename Enter the WRED profile name to view the profile details. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Modified to display the global WRED state. 9.10(0.
test cam-usage Check the Input Policy Map configuration for the CAM usage. S4048–ON Syntax test cam-usage service-policy input policy-map stack-unit {[number port-set portpipe number] | [all]} Parameters policy-map Enter the policy map name. stackunit number (OPTIONAL) Enter the keyword stack-unit then the stack-unit slot number. port-set portpipe Enter the keywords port-set then the stack-unit port pipe number. The range is number from 0 or 1.
Field Description NOTE: The CAM entries reserved for the default rules are not included in the Available CAM column; free entries, from the default rules space, cannot be used as a policy map for the classification rules. Estimated CAM per Port Indicates the number of free CAM entries required (for the classification rules) to apply the input policy map on a single interface.
Defaults none Command Modes CONFIGURATION (config-wred) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
Defaults dot1p Enter the keyword dot1p to specify trust dot1p configuration. fallback Enter the keyword fallback to classify packets according to their DSCP or dot1p value as a secondary option in case no match occurs against the configured class maps. none Command Modes CONFIGURATION (conf-policy-map-in) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Table 6. Default Mapping (continued) DSCP/CP hex DSCP Range (XXX) Definition Traditional IP Precedence S6000 Internal Queue ID S-Series Internal Queue ID DSCP/CP Decimal 100XXX AF4 (Assured Forwarding) Flash Override 4 2 32–47 011XXX AF3 Flash 3 1 16–31 010XXX AF2 Immediate 2 1 16–31 001XXX AF1 Priority 1 0 0–15 000XXX BE (Best Effort) Best Effort 0 0 0–15 wred Designate the WRED profile to yellow or green traffic.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information To assign drop precedence to green or yellow traffic, use this command. If there is no honoring enabled on the input, all the traffic defaults to green drop precedence. Related Commands ● wred-profile — creates a WRED profile and name that profile. ● trust — defines the dynamic classification to trust DSCP.
● If neither endpoint is ECN-capable, the packet may be dropped based on the WRED drop probability. This behavior is the identical treatment that a packet receives when WRED is enabled without ECN configured on the router. When you enable wred ecn, and the number of packets in the queue is above the maximum threshold, packets are dropped based on the drop probability. This behavior is the identical treatment a packet receives when WRED is enabled without ECN configured on the router.
Usage Information Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred). Related Commands ● threshold — specifies the minimum and maximum threshold values of the WRED profile. DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red.
● All DSCP values that are not specified as yellow or red are colored green. ● A DSCP value cannot be in both the yellow and red lists. Setting the red or yellow list with any DSCP value that is already in the other list results in an error and no update to that list is made. ● Each color map can only have one list of DSCP values for each color; any DSCP values previously listed for that color that are not in the new DSCP list are colored green.
qos dscp-color-policy Associates the DSCP color map profile with an interface so that all IP packets received on it is given a color based on that color map. Syntax dscp-color-policy color-map-profile-name To remove a color policy map profile, use the no dscp-color-policy color-map-profile-name command. Parameters Defaults color-mapprofile-name Enter the color map profile name. The name can have a maximum of 32 characters.
Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps.
47 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. S4048–ON Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command.
Related Commands ● redistribute — allows you to redistribute routes learned by other methods. description Enter a description of the RIP routing protocol. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the RIP protocol (80 characters maximum). none Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
To return to the default values, use the no distance weight [ip-address mask] command. Parameters Defaults weight Enter a number from 1 to 255 for the weight (for prioritization). The default is 120. ip-address (OPTIONAL) Enter the IP address, in dotted decimal format (A.B.C.D), of the host or network to receive the new distance metric. mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x).
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. S4048–ON Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
2 Defaults (OPTIONAL) Enter the number 2 for RIP version 2. RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. S4048–ON Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command.
Usage Information Related Commands When a neighbor router is identified, unicast data exchanges occur. Multiple neighbor routers are possible. To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. ● passive-interface — sets the interface to only listen to RIP broadcasts. network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command.
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. S4048–ON Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters prefix-list-name Enter the name of an established Prefix list to determine which incoming routes are modified.
Usage Information When the offset metric is applied to an interface, that value takes precedence over an offset value that is not extended to an interface. Related Commands ● ip prefix-list — enters PREFIX-LIST mode and configure a prefix list. output-delay Set the interpacket delay of successive packets to the same neighbor. S4048–ON Syntax output-delay delay To return to the switch software defaults for interpacket delay, use the no output-delay command.
passive-interface Suppress routing updates on a specified interface. S4048–ON Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. Parameters interface Enter the following information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
redistribute Redistribute information from other routing instances. Syntax redistribute {connected | static} To disable redistribution, use the no redistribute {connected | static} command. Parameters Defaults connected Enter the keyword connected to specify that information from active routes on interfaces is redistributed. static Enter the keyword static to specify that information from static routes is redistributed. Not configured.
Parameters tag (OPTIONAL) Enter the name of the IS-IS routing process. level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16.
metric metric- value route-map map- name Defaults (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16. (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. DellEMC(conf-router_rip)# show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1 DellEMC(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated.
Usage Information Example Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24...
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
flush Defaults ● ● ● ● Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table. The flush value should be greater than the update value. The range is from zero (0) to 4294967295. The default is 240 seconds.
Command Modes ROUTER RIP Command History Related Commands 1382 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
48 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table.
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
show rmon Display the RMON running status including the memory usage. S4048–ON Syntax show rmon Defaults none Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
show rmon alarms Display the contents of the RMON alarm table. S4048–ON Syntax show rmon alarms [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) 1390 This guide is platform-specific.
-------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 6 1.3.6.1.2.1.1.3 7 1.3.6.1.2.1.1.3 8 1.3.6.1.2.1.1.3 9 1.3.6.1.2.1.1.3 10 1.3.6.1.2.1.1.3 11 1.3.6.1.2.1.1.3 12 1.3.6.1.2.1.1.3 13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table.
Example (Index) Example (Brief) 1392 Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf)# rmon event 111 -> DellEMC(conf)# rmon event 112 log -> DellEMC(conf)# rmon event 113 trap private -> DellEMC(conf)# rmon event 114 log trap public-> options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none.
21 21 22 22 DellEMC# show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. S4048–ON Syntax Parameters Defaults show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) This guide is platform-specific.
falling threshold: 300, RMON event index: 4 alarm sampling failed 0 times. alarm owner: alarm storage type: non-volatile. alarm status: OK DellEMC# Example (Brief) DellEMC# show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 DellEMC# show rmon history Display the contents of the RMON Ethernet history table.
Example (Index) Example (Brief) Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
Usage Information Example (Index) Example (Brief) Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The log table has a maximum of 500 entries.
Example (Index) Example (Brief) Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
6003 101236775 6004 101236775 9001 134529054 9002 134529054 9003 134791198 9004 134791198 DellEMC# 1398 Remote Monitoring (RMON) TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet 2/1 2/1 3/2 3/2 3/1 3/1
49 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
Related Commands ● protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● forward-delay — changes the wait time before RSTP transitions to the Forwarding state.
Usage Information Example Related Commands RSTP is not enabled when you enter RSTP mode. To enable RSTP globally on the system, use the no disable command from RSTP mode. DellEMC(conf)# protocol spanning-tree rstp DellEMC(config-rstp)# no disable ● disable — disables RSTP globally on the system. show config View the current configuration for the mode. Only non-default values are displayed.
Parameters brief (OPTIONAL) Enter the keyword brief to view a synopsis of the RSTP configuration information. guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example (Brief) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
Name PortID Prio ---------- ------Te 4/2 128.418 128 Te 4/1 128.419 128 Te 4/8 128.426 128 Te 4/9 128.427 128 Interface Name Role ----------Te 4/2 Desg Te 4/1 Desg Te 4/8 Root Te 4/9 Altr DellEMC# Example (EDS, LBK) Cost Sts Cost Bridge ID PortID --- ------- -------------------- -------20000 FWD 20000 16384 0001.e801.6aa8 128.418 20000 FWD 20000 16384 0001.e801.6aa8 128.419 20000 FWD 20000 8192 0001.e805.e306 128.130 20000 BLK 20000 8192 0001.e805.e306 128.
spanning-tree rstp Configure an RSTP interface with one of these settings: port cost, edge port with optional bridge port data unit (BPDU) guard, port priority, loop guard, or root guard. Syntax Parameters spanning-tree rstp {cost port-cost | edge-port [bpduguard [shutdown-onviolation]] | priority priority | {loopguard | rootguard}} cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added support for the optional guard keyword on the C-Series, S-Series, and ESeries. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the hardware shutdown-on-violation options. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the optional bridge port data unit (BPDU) guard. 6.2.1.1 Introduced on the E-Series.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
50 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
51 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant.
dot1x Enter the keyword dot1x to send accounting information when a dot1x user has logged in. commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: ● For name, enter a user-defined name of a list of accounting methods.
Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. ● aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL.
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.
Defaults commands { level | role role-name } Enter the keyword commands followed by either a privilege level for accounting of commands executed at that privilege level, or enter the keyword role then the role name for authorization of commands executed by a user with that user role. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands. none Command Modes LINE Command History Related Commands This guide is platform-specific.
Defaults default Define the default list of authorization methods. local Use the authorization parameters on the system to perform authorization. tacacs+ Use the TACACS+ protocol to perform authorization. none Enter the keyword none to apply no authorization. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS.
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys.
verify that you have successfully obscured passwords and keys, use the show running-config command orshow startup-config command. If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command. Related Commands ● show running-config— Display the current configuration and display changes from the default values. ● service password-encryption— Encrypts all passwords configured in the system.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used.
● radius: use the RADIUS servers configured with the radius-server host command. ● tacacs+: use the TACACS+ servers configured with the tacacs-server host command. ... method4 Defaults (OPTIONAL) Enter up to four additional methods. In the event of a “no response” from the first method, the system applies the next configured method (up to four configured methods). Not configured (that is, no authentication is performed).
After configuring the aaa authentication login command, configure the login authentication command to enable the authentication scheme on terminal lines. Connections to the SSH server work with the following login mechanisms: local, radius, and tacacs. Related Commands ● ● ● ● login authentication — enables AAA login authentication on the terminal lines. password — creates a password. radius-server host — specifies a RADIUS server host. tacacs-server host — specifies a TACACS+ server host.
Defaults Not configured. Command Modes LINE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
encryption-type (OPTIONAL) Enter the number 8 or 0 as the encryption type. Enter 8 to enter the sha256–based hashed password. password Defaults Enter a text string, up to 96 characters long, as the clear text password. No password is configured. level = 15. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Only Dell EMC Networking Technical Support staff use this command. enable secret Change the password for the enable command.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: ● Start with a letter, not a number.
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.6.0.0 Revised introductory and usage guidelines description. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
user-lockoutperiod minutes (OPTIONAL) Enter the keyword user-lockout-period then the number of minutes. The range is from 1 to 1440 minutes. The default is 0 minutes and the lockout-period is not enabled. This parameter enhances the security of the switch by locking out the local user account if there are more number of unsuccessful login attempts than what is configured using the max-retry parameter. The default value is 3 times.
Example In the following example, after 5 un-successful login attempts, the session (SSH/TELNET) goes into a locked state for 5 minutes. If all the 10 sessions are locked out with 5 un-successful attempts in each session, no users can login during the lockout-period. DellEMC(conf)# password-attributes max-retry 5 lockout-period 5 Related Commands ● password — specifies a password for users on terminal lines. secure-cli enable Enable the secured CLI mode.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security. When the passwords are encrypted, you cannot return them to plain text unless you re-configure them.
Example Version Description pre-6.1.1.0 Introduced on the E-Series. DellEMC# show privilege Current privilege level is 15. DellEMC# DellEMC# show privilege Current privilege level is 14. DellEMC# DellEMC# show privilege Current privilege level is 10. DellEMC# Related Commands ● privilege level (CONFIGURATION mode) — assign access control to different command modes. show users Allows you to view information on all users logged in to the switch.
Usage Information Example Related Commands The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lines currently in use. User Displays the user name of all users logged in. Host(s) Displays the terminal line status. Location Displays the IP address of the user.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
privilege level Enter the keyword privilege then a number from zero (0) to 15. role role-name Enter the keyword role followed by the role name to associate with that user ID. secret Enter the keyword secret then the encryption type. sha256-password Enter the keyword sha256-password then the encryption-type or the password. Defaults The default encryption type for password option is 0. The default encryption type for secret option is 5. The default encryption type for sha256-password option is 8.
● ● ● ● ● Related Commands A A A A A minimum minimum minimum minimum minimum of of of of of eight characters in length one lower case letter (a to z) one upper case letter (A to Z) one numeric character (0 to 9) one special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") ● password — specifies a password for users on terminal lines. ● show running-config — views the current configuration. RADIUS Commands The following RADIUS commands are supported by Dell EMC Networking OS.
ipv6–addr Enter the keyword ipv6–addr to specify the IPv6 address of the DAC. hostname Enter the keyword hostname to enter the name of the host. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to associate a VRF with the client. key (Optional) Enter the keyword key to specify an encryption key. encryption-type (Optional) Enter either 0 or 7 as the encryption type for the specified key. The options are: ● 0 – implies that the key is not encrypted and is stored as clear text.
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. coa-bounce-port Configure NAS to allow or reject the port bounce RADIUS messages from DAC. Syntax coa-bounce-port To remove the port bounce configuration, enter the no coa-bounce-port command. Defaults Enabled.
coa-reauthenticate Configure NAS to re-authenticate dot1x user session requests from DAC. Syntax coa-reauthenticate To allow or reject re-authentication requests, enter the no coa-reauthenticate command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Version Description pre-6.2.1.0 Introduced on the E-Series. da-rsp-timeout Configure timeout value for the back end task to respond to DAC requests. Syntax da-rsp-timeout minutes To undo the configuration, enter the no da-rsp-timeout command. Defaults Parameters 10 Minutes. minutes Enter the time out value. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Time for DAS to wait before the back end response is received. Command History This guide is platform-specific.
dynamic-auth-enable Configure NAS to receive and process dynamic authorization messages. Syntax dynamic-auth-enable To stop NAS from receiving and processing dynamic authorization messages, use the no dynamicauth-enable command. Defaults Disabled. Command Modes ● CONF-DYNAMIC-AUTH Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.
Defaults Disabled. Command Modes ● CONFIGURATION Usage Information ● All dynamic authorization commands are configured by entering this mode. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
radius-server group Creates or deletes a group of radius servers. Syntax Parameters Defaults radius-server group group-name group-name Enter the group name that denotes the group of RADIUS servers. Not configured. Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
auth-port port- number acct-port port- number retransmit retries (OPTIONAL) Enter the keywords auth-port then a number as the port number. The range is from zero (0) to 65535. The default port-number is 1812. (OPTIONAL) Enter the keywords acct-port then a number as the port number. The range is from 1 to 65535. The default port-number is 1813. (OPTIONAL) Enter the keyword retransmit then a number as the number of attempts. This parameter overwrites the radius-server retransmit command.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. To configure any number of RADIUS server hosts for each server host that is configured, use this command. Dell EMC Networking OS searches for the RADIUS hosts in the order they are configured in the software.
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes RADIUS SERVER GROUP Command History Usage Information This guide is platform-specific.
Parameters encryption-type (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: ● 0 is the default and means the key is not encrypted and stored as clear text. ● 7 means that the key is encrypted and hidden. key Defaults Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 96 characters long. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
Parameters Defaults retries Enter a number of attempts that the Dell OS tries to locate a RADIUS server. The range is from zero (0) to 100. The default is 3 retries. 3 retries Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
replay-protection-window Configure replay protection window period to drop the duplicate packets. Syntax replay-protection-window minutes To undo the configuration, enter the no replay-protection-window command. Defaults Parameters 5 Minutes. minutes Enter the number of minutes to drop the packets. The range is from 1 to 10 minutes.
TACACS+ Commands Dell EMC Networking OS supports TACACS+ as an alternate method for login authentication. tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command . Parameters Defaults group-name Enter the name of the TACACS server group. Not configured.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Example Related Commands DellEMC(conf)# tacacs-server group group1 DellEMC(conf-tacacs-group)# tacacs-server host 1.1.1.1 key secret DellEMC(conf-tacacs-group)# tacacs-server host 2.2.2.2 key secret DellEMC(conf-tacacs-group)# tacacs-server vrf vrf1 source-interface tengigabitethernet 1/42 DellEMC(conf-tacacs-group)# show config ! tacacs-server group group1 tacacs-server vrf vrf1 source-interface TenGigabitEthernet 1/42 tacacs-server host 1.1.1.1 key 7 9a2f3ec0c65c6f41 tacacs-server host 2.2.2.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
● If an 802.1X port is authenticated and put in the RADIUS server assigned VLAN, any change to the port access VLAN configuration does not take effect. ● The 802.1X with VLAN assignment feature is not supported on trunk ports, dynamic ports, or with dynamic-access port assignment through a VLAN membership. dot1x authentication (Configuration) Enable dot1x globally; dot1x must be enabled both globally and at the interface level.
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed attempts, the interface is moved to the authentication failed VLAN.
dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port[/subport]) Command History Usage Information This guide is platform-specific.
dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell EMC Networking OS attempts to authenticate the host based on its MAC address. Syntax [no] dot1x mac-auth-bypass Defaults Disabled Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator performs authentication only when port-control is set to auto. dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command.
Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated. The range is from 1 to 31536000 (1 year). The default is3600 (1 hour). 3600 seconds (1 hour) Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
Version Description 7.4.1.0 Introduced on the E-Series. dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Syntax dot1x supplicant-timeout seconds To return to the default, use theno dot1x supplicant-timeout command. Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. DellEMC#show dot1x interface fortyGigE 1/48 802.
Auth PAE State: Backend State: DellEMC# Initialize Initialize SSH and SCP Commands Dell EMC Networking OS supports secure shell (SSH) protocol version 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted and use authentication. crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
Usage Information The host keys are required for key-exchange by the SSH server. If the keys are not found when you enable the server (ip ssh server enable), the keys are automatically generated. This command requires user interaction and generates a prompt prior to overwriting any existing host keys. NOTE: Only a user with superuser permissions should generate host-keys. Example Related Commands DellEMC(conf)# crypto key generate rsa Enter key size <1024-2048>. Default<1024> : Host key already exists.
Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command.
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh challenge–response–authentication Enable challenge response authentication for SSHv2.
● aes128-cbc ● 3des-cbc Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON, S6000, S6000–ON, S5000, S4810, S4820T, S3048– ON, S4048–ON, MXL, C9010, S3100 series, and Z9100-ON.
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server. Syntax ip ssh hostbased-authentication enable To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbasedauthentication enable command.
Related Commands ● ip ssh pub-key-file — public keys of trusted hosts from a file. ● ip ssh rhostsfile — trusted hosts and users for rhost authentication. ip ssh key-size Configure the size of the server-generated RSA SSHv1 key. Syntax Parameters Defaults ip ssh key-size 512-869 512-869 Enter the key-size number for the server-generated RSA SSHv1 key. The range is from 512 to 869. The default is 768.
● ● ● ● ● Defaults hmac-sha2-256 hmac-sha1 hmac-sha1–96 hmac-md5 hmac-md5-96 The default list of MAC algorithm is in the order as shown below: When FIPS mode is enabled: ● hmac-sha2–256 ● hmac-sha1 ● hmac-sha1–96 When FIPS mode is disabled: ● ● ● ● ● hmac-sha2-256 hmac-sha1 hmac-sha1–96 hmac-md5 hmac-md5-96 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file.
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL ip ssh rhostsfile Specify the rhost file used for host-based authorization. Syntax Parameters Defaults ip ssh rhostsfile {WORD} WORD Enter the rhost file name for the host-based authentication.
This file contains hostnames and usernames, for which hosts and users, rhost-authentication can be allowed. NOTE: For rhostfile and pub-key-file, the administrator must FTP the file to the switch. ip ssh rsa-authentication (Config) Enable RSA authentication for the SSHv2 server. Syntax ip ssh rsa-authentication enable To disable RSA authentication, use the no ip ssh rsa-authentication enable command. Parameters Defaults enable Enter the keyword enable to enable RSA authentication for the SSHv2 server.
To disable SSH server functions, use the no ip ssh server {ciphers cipher-list} {enable | port port-number} [kex key-exchange-algorithm] [mac hmac-algorithm] command. Parameters enable Enter the key word enable to start the SSH server. ciphers cipher- Enter the keyword ciphers and then a space-delimited list of ciphers that the SSH server supports. The following ciphers are available.
● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 When FIPS is enabled, the default key-exchange-algorithm is diffie-hellmangroup14-sha1. When FIPS is not enabled, the default key-exchange-algorithms are the following: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1, ● diffie-hellman-group14-sha1 port port-number (OPTIONAL) Enter the keyword port then the port number of the listening port of the SSH server. The range is from 1 to 65535. The default is 22.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22. NOTE: Starting with Dell EMC Networking OS Release 9.2(0.0), SSH server is enabled by default.
Defaults None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. If you configure a VRF for an SSH session, then you need not explicitly mention the same VRF for the SSH client sessions intended for that VRF. The vrf attribute in the ip ssh vrf command is applicable for both the SSH client as well as the COPY (SCP) commands.
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command is useful if the remote SSH client implements Strict Host Key Checking. You can copy the host key to your list of known hosts.
Example Related Commands Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : aes256-ctr,aes256-cbc,aes192-ctr,aes192cbc,aes128-ctr,aes128-cbc,3des-cbc. SSH server macs : hmac-sha2-256,hmac-sha1,hmac-sha1-96,hmacmd5,hmac-md5-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffiehellman-group1-sha1,diffie-hellman-group14-sha1.
Usage Information Example Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash://ADMIN_DIRssh/knownhosts file. DellEMC# show ip ssh client-pub-keys 4.8.1.
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash:/ADMIN_DIR/ssh/authorizedkeys.username file.
● aes128-cbc : Force ssh to use aes128-cbc encryption cipher ● aes192-cbc : Force ssh to use aes192-cbc encryption cipher ● aes256-cbc : Force ssh to use aes256-cbc encryption cipher ● aes128-ctr : Force ssh to use aes128-ctr encryption cipher ● aes192-ctr : Force ssh to use aes192-ctr encryption cipher ● aes256-ctr : Force ssh to use aes256-ctr encryption cipher -l username (OPTIONAL) Enter the keyword -l then the user name used in this SSH session.
Version Description ● hmac-sha2-256 ● hmac-sha2-256-96 Usage Information Example 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Added support for the -c and -m parameters on the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Added IPv6 support. Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ● show ip dhcp snooping — display the contents of the DHCP binding table.
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping vlan Enable DHCP Snooping on one or more VLANs. Syntax [no] ip dhcp snooping vlan name Parameters Defaults name Enter the name of a VLAN on which to enable DHCP Snooping. Disabled.
show ip dhcp snooping Display the contents of the DHCP binding table. Syntax show ip dhcp snooping binding Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
aaa authorization role-only Configure authentication to use the user’s role only when determining if access to commands is permitted. Syntax aaa authorization role-only To return to the default setting, use the no aaa authentication role-only command. Parameters Defaults name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
router for Router mode Defaults addrole Enter the keyword addrole to add permission to the command. You cannot add or delete rights for the sysadmin role. deleterole Enter the keyword deleterole to remove access to the command. You cannot add or delete rights for the sysadmin role. role-name Enter a text string for the name of the user role up to 63 characters. These are 3 system defined roles you can modify: secadmin, netadmin, and netoperator.
Command Modes EXEC Privilege Command History Examples This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role from scratch.
Table 7. Suppressed ICMPv4 message types (continued) ICMPv4 Message Types Router advertisement (9) Router solicitation (10) Time exceeded (11) IP header bad (12) Timestamp request (13) Timestamp reply (14) Information request (15) Information reply (16) Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMPv4 message type Echo request (8). Table 8.
drop icmp Drops the ICMPv4 and ICMPv6 packets. Syntax drop {icmp | icmp6} Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other Platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on the S4810, S4820T, S3048–ON, S3100 Series, S4048–ON, S5000, S6000, S6000–ON, Z9500, Z9100–ON, S6100–ON, S6010–ON, S4048T–ON, C9000, and MXL.
● ● ● ● A A A A minimum minimum minimum minimum of of of of one one one one lower case letter (a to z) upper case letter (A to Z) numeric character (0 to 9) special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") If your password does not meet the criteria, the system does not accept your password. When you upgrade the Dell EMC Networking OS image, ensure that you upgrade the boot loader. CAUTION: After configuring the boot access password, save it to a secure location.
root-access password Configure the root access password. Syntax root-access password [encryption-type] root-password To reset to the default password, use the no root-access password command. Parameters encryption-type (OPTIONAL) Enter an encryption type for the root password that you enter. ● 0 directs the system to store the password as clear text. ● 7 directs the system to store the password with a dynamic salt.
Command History Usage Information Example Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, MXL, and FN-IOM. When you reboot the system using the reload command, the system performs OS image verification on the primary boot image.
Command Modes CONFIGURATION Command History Example Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM.
52 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID. The range is from 1 to 4094. count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Debug disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
Example Related Command Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command ● show protocol-tunnel — displays tunneling information for all VLANs.
protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters Defaults rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History Example Related Commands 1526 This guide is platform-specific.
show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax Parameters Defaults show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094. none Command Modes EXEC Command History Example Example (Specific VLAN) Related Commands This guide is platform-specific.
53 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
Usage Information Version Description 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S-Series, Z-Series, and MXL switch. 9.2(1.0) Introduced on the Z9500. Usage Information When you enable ingress sFlow on an interface, flow sampling is done on any incoming traffic.
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Dell EMC Networking OS enhances the sflow implementation for real time traffic analysis on the E-Series to provide extended gateway information in cases where the destination IP addresses are learned by different routing protocols and for cases where the destination is reachable over ECMP.
Parameters Defaults interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is 20 seconds. 20 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.
54 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
UDP-MIB RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.50 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Usage Information Use this command to map SNMP context to a VRF instance within a community in SNMPv2c and SNMPv3. The no version of this command turns off this feature. snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific.
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB. If a community string is configured without a security-name (for example, snmp-server community public ro), the community is mapped to a default security-name/group: ● v1v2creadu / v1v2creadg — maps to a community with ro (read-only) permissions. ● v1v2cwriteu/ v1v2cwriteg — maps to a community with rw (read-write) permissions. The community-name parameter indexes this command.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the following two SNMP notification options: syslog-reachable and syslog-unreachable. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only.
vrf vrf-name Enter the keyword vrf followed by the name of the VRF that is used to reach the device. NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device. If no VRF is specified, then the default VRF is used. udp-port port- Enter the keywords udp-port followed by the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. number engineID Defaults As above.
snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.2 Added support for the access parameter. 8.3.7.0 Introduced on the S4810. 7.6.1.
NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps. informs (OPTIONAL) Enter the keyword informs to send inform notifications to the specified host. The default is traps.
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148 and S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
To send an inform, use the following steps: 1. 2. 3. 4. 5. Related Commands Configure a remote engine ID. Configure a remote user. Configure a group for this user with access rights. Enable traps. Configure a host to receive informs. ● snmp-server enable traps — enables SNMP traps. ● snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server.
snmp-server packetsize Set the largest SNMP packet size permitted. Wen the SNMP server is receiving a request or generating a reply, use the snmpserver packetsize global configuration command. Syntax snmp-server packetsize byte-count Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32. Packet sizes are 8000 bytes, 16000 bytes, 32000 bytes, and 64000 bytes. 8 Command Modes CONFIGURATION Command History This guide is platform-specific.
● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults The IP address assigned to the management interface is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Parameters name Enter the name of the user (not to exceed 20 characters), on the host that connects to the agent. group_name Enter a text string (up to 20 characters long) as the name of the group. The following groups are created for mapping to read/write community/security-names (defaults): ● v1v2creadu — maps to a community with ro permissions. ● 1v2cwriteu — maps to a community rw permissions.
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
5009 3 auth md5 authpasswd Related Commands ● show snmp user — displays the information configured on each SNMP user name. snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826. RFCs for SNMPv3 define two authentication hash algorithms, namely, HMAC-MD5-96 and HMAC-SHA1-96.
Usage Information To enable robust, effective protection and security for SNMP packets transferred between the server and the client, you can use the snmp-server user username group groupname 3 auth authentication-type auth-password priv aes128 priv-password to specify that AES128-CFB encryption algorithm needs to be used. You cannot modify the FIPS mode if SNMPv3 users are already configured and present in the system.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The oid-tree variable is a full sub-tree starting from 1.3.6 and cannot specify the name of a sub-tree or a MIB. The following Example configures a view named rview that allows access to all objects under 1.3.6.1. DellEMC# conf DellEMC#(conf) snmp-server view rview 1.3.6.
snmp trap link-status Enable the interface to send SNMP link traps, which indicate whether the interface is up or down. Syntax snmp trap link-status To disable sending link trap messages, use the no snmp trap link-status command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator.
Example Related Commands DellEMC(conf)# clear logging auditlog ● show logging auditlog — display the audit log. default logging buffered Return to the default setting for messages logged to the internal buffer. Syntax default logging buffered Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging monitor — set the logging monitor parameters. ● terminal monitor — send system messages to the terminal/monitor. default logging trap Return to the default settings for logging messages to the Syslog servers.
logging Configure an IP address or host name of a Syslog server where logging messages are sent. Multiple logging servers of both IPv4 and/or IPv6 can be configured. Syntax logging {ip-address | ipv6-address | hostname} {{udp {port}} | {tcp {port}} [vrf vrf-name] To disable logging, use the no logging command. Parameters ip-address Enter the IPv4 address in dotted decimal format. ipv6-address Enter the IPv6 address in the x:x:x:x::X format.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Multiple logging servers of both IPv4 and/or IPv6 can be configured. Related Commands ● logging on — enables the logging asynchronously to logging buffer, console, Syslog server, and terminal lines. ● logging trap — enables logging to the Syslog server based on severity. logging buffered Enable logging and specify which messages are logged to an internal buffer.
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you decrease the buffer size, all messages stored in the buffer are lost. Increasing the buffer size does not affect messages stored in the buffer. Related Commands ● clear logging — clears the logging buffer.
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● clear logging — clears the logging buffer. ● default logging console — returns the logging console parameters to the default setting. ● show logging — displays the logging setting and system messages in the internal buffer. logging extended Logs security and audit events to a system log server.
logging facility Configure the Syslog facility used for error messages sent to Syslog servers. Syntax logging facility [facility-type] To return to the default values, use the no logging facility command.
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging — enables logging to a Syslog server ● logging on — enables logging. logging history Specify which messages are logged to the history table of the switch and the SNMP network management station (if configured).
Version Description E-Series legacy command Usage Information When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network management station. Related Commands ● show logging — displays information logged to the history buffer. logging history size Specify the number of messages stored in the Dell EMC Networking logging history table.
logging monitor Specify which messages are logged to Telnet applications. Syntax logging monitor [level] To disable logging to terminal connections, use the no logging monitor command. Parameters Defaults level Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging. 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific.
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
all Enter the keyword all to turn off all. limit number-of- Enter the keyword limit then the number of buffers to be queued for the terminal after which new messages are dropped. The range is from 20 to 300. The default is 20. buffers Defaults Disabled. If enabled without the level or number-of-buffers options specified, level = 2 and number-of-buffers = 20 are the defaults. Command Modes LINE Command History This guide is platform-specific.
Defaults 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. To display syslog messages in a RFC 3164 or RFC 5424 format, use the log version command in configuration mode. By default, the system log version is set to 0.
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
Command Modes EXEC Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Example Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
55 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE 1.0.8802.1.1.2.1.5.47 lldpXMedTopology 95.0.1 ChangeDetected lldp-ext-med.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 113 TRAP OID MIB File Explanation TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 132 TR_VLT_ICL_BW_ THRESHOLD_EXC EED 133 TR_VLT_DOMAIN _CFG_ERROR 134 135 Object Name MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclBwUs .2.0.5 ageExceed DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The IFM agent generates this notification to denote the change in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1. Above threshold" 1.3.6.1.4.1.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 138 TR_ENT_CONFIG_ 1.3.6.1.2.1.47.2.0.1 CHANGE 1602 SNMP Traps TRAP OID Object Name MIB File Explanation entConfigChange entity.mib An entConfigChange notification is generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation notificationevents, e.g., due to throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
56 Stacking All commands in this chapter are specific to the Dell EMC Networking OS. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, see the Stacking S-Series Switches section in the Dell EMC Networking OS Configuration Guide. CAUTION: You cannot enable stacking simultaneously with virtual link trunking (VLT).
Usage Information ● To form a mixed-mode stack, use only the 40G ports between the range 49 to 54. ● You cannot form a mixed-mode stack using the 10G ports. Because, the 10G ports on the S4048T are copper ports; where as, the 10G ports on the S4048-ON are SFP ports. ● It is mandatory to enable mixed-mode stacking on the S4048-ON and S4048T-ON switches before joining a mixed-mode stack. ● Stack election is based on the priority or the MAC address of the stack units as in homogenous stacking.
Do you System ! Apr 10 config want to reload? Proceed[confirm yes/no]:yes configuration has been modified. Save? [yes/no]: yes 19:19:18: %STKUNIT2-M:CP %FILEMGR-5-FILESAVED: Copied runningto startup-config in flash by default Apr 10 19:19:18: %STKUNIT2-M:CP %CHMGR-5-RELOAD: User request to reload the chassis syncing disks... done unmounting file systems... unmounting /f10/flash (/dev/wd0e)... unmounting /f10/ConfD/db (mfs:479)... unmounting /usr/pkg (/dev/wd0i)... unmounting /boot (/dev/wd0b)...
Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the running-config. Related Commands show redundancy — displays the current redundancy status. redundancy force-failover stack-unit Force the standby unit in the stack to become the management unit. Syntax redundancy force-failover stack-unit Defaults Not enabled.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the members option.
00:15:01: %STKUNIT2-S:CP %IFMGR-1-DEL_PORT: Removed port: Te 4/1-4/48, Fo 4/51-4/52, DellEMC#00:15:08: %S4048-ON:1 %IFAGT-5-STACK_PORT_LINK_DOWN: Changed stack port state to down: 1/49 00:15:08: %STKUNIT1-M:CP %CHMGR-2-STACKUNIT_DOWN: stack-unit 4 down card removed DellEMC# Related Commands ● reload – reboots Dell EMC Networking OS. show redundancy Display the current redundancy configuration (status of automatic reboot configuration on stack management unit).
Primary Stack-unit: Auto Data Sync: Failover Type: Auto reboot Stack-unit: Auto failover limit: mgmt-id 1 Full Hot Failover Enabled 3 times in 60 minutes -- Stack-unit Failover Record ------------------------------------------------Failover Count: 0 Last failover timestamp: None Last failover Reason: None Last failover type: None -- Last Data Block Sync Record: ------------------------------------------------stack-unit Config: succeeded Apr 20 2016 SSMGR: succeeded Apr 20 2016 Start-up Config: succeeded A
Example Example (Status) Field Description Interface The unit/port ID of the connected stack port on this unit. Link Speed Link Speed of the stack port (12 or 42) in Gb/s. Admin Status The only currently listed status is Up. Connection The stack port ID to which this unit’s stack port is connected.
2/54 3/53 3/54 4/53 4/54 5/53 5/54 6/53 6/54 DellEMC# Related Commands 3/53 2/54 4/53 3/54 5/53 4/54 6/54 1/53 5/54 ● reset stack-unit – resets the designated stack member. ● show hardware stack-unit – displays the data plane or management plane input and output statistics of the designated component of the designated stack member. ● show system – displays the current status of all stack members or a specific member.
model-identifier Defaults Enter the model identifier of the switch to be added as a stack member. This identifier is also referred to as the provision type. When this value is not set, a switch joining the stack is given the next available sequential stack member identifier. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Usage Information The following message displays to confirm the command. Setting ports Fo 1/60 as stack group will make their interface configs obsolete after a reload.[confirm yes/no]: If “y” is entered, all nondefault configurations on any member ports of the current stack group will be removed when the unit is rebooted.
57 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
show storm-control broadcast Display the storm control broadcast configuration. Syntax Parameters show storm-control broadcast [interface] interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
Parameters Defaults percentagedecim E-Series Only: Enter the percentage of broadcast traffic allowed in or out of the al_value in | out network. Optionally, you can designate a decimal value percentage, for example, 55.5%. The decimal range is from .1 to .9. wred-profile name E-Series Only: Enter the keyword wred-profile followed by the profile name to designate a wred-profile. packets_per_sec ond in Enter the packets per second of broadcast traffic allowed into the network.
Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMUX (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series.
Version Description 7.6.1.0 Introduced on the C-series and S-Series. storm-control PFC/LLFC Shut down the port if it receives the PFC/LLFC frames more than the configured rate. Syntax Parameters Defaults storm-control pfc-llfc [pps]in shutdown pfc-llfc in Enter the keyword pfc-llfc to get the flow control traffic. The range is from 0 to 33554368 packets per second. shutdown Enter the keyword shutdown to shut down the port when the rate exceeds.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.
58 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree — enter SPANNING TREE mode on the switch.
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● max-age — changes the wait time before STP refreshes protocol configuration information. ● hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults seconds Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
Example Field Description “Designated port...” Displays the designated port ID. DellEMC# show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
Example (Guard) Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
59 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
SUPASSIST_PKG_UNINSTALLED: SupportAssist package uninstalled DellEMC(conf)# Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific.
This command starts the configuration wizard for the SupportAssist. At any time, you can exit by entering Ctrl-C. If necessary, you can skip some data entry. Once you exit the wizard, the Dell EMC Networking OS starts a full transfer. support-assist activity Trigger an activity event immediately. Syntax support-assist activity {full-transfer | core-transfer} start now Parameters full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information.
Command Modes SUPPORTASSIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. Introduced the core-transfer and event-transfer parameters. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
contact-person Configure the contact name for an individual. Syntax contact-person [first ] last To remove the contact person and all their details, use the no contact-person [first ] last command. Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes. last-name Enter the last name for the contact person.
Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode. Syntax server {default | server-name} To delete a server, use the no server server-name command. Parameters Defaults default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred.
local-file-name Enter the name of the local action-manifest file, up to 32 characters long. Allowable characters are: a to z, A to Z, 0 to 9, -, _, and space. Command Modes SUPPORTASSIST ACTIVITY FULL-TRANSFER SUPPORTASSIST ACTIVITY EVENT-TRANSFER Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Usage Information To replace the default action-manifest with a customized one, copy the action-manifest file to the system using the action-manifest get command and then use the action-manifest install command. To revert to the default action-manifest file, use the action-manifest install default command.
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
address Configure the address information for the company. Syntax address [city company-city] [{province | region | state} name] [country company-country] [{postalcode | zipcode] company-code] To remove a portion of the company address information, use the no address [city | province | region | state | country | postalcode | zipcode] command. For example, to remove the city alone, use the no address city command. To remove the complete company contact information, use the no address command.
address2..addres (OPTIONAL) Enter the street address of the company site. Up to 8 fields are s8 allowed. Command Modes SUPPORTASSIST COMPANY Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
email-address Configure the email addresses to reach the contact person. Syntax email-address primary email-address [alternate email-address] To remove an email address, use the no email-address command. To remove the primary and the alternate email addresses, use the no email-address primary and no email-address alternate commands respectively. Parameters primary email- address alternate emailaddress Enter the keyword primary then the primary email address for the person.
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. The phone numbers may contain country codes, area codes and extensions, if necessary. Allowable characters are 0 to 9, x, (, ), - and +. This command is optional for SupportAssist service configuration.
stop-time HH:MM Enter the keywords stop-time then a stopping time expressed as HH:MM. Use the 24-hour clock format. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
Command Modes SUPPORTASSIST SERVER Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
performance information, network configuration information, host/server configuration & performance information and related data (Collected Data) and transmits this information to Dell. By downloading SupportAssist and agreeing to be bound by these terms and the Dell end user license agreement, available at: www.dell.
Example DellEMC# show running-config support-assist ! support-assist enable all ! activity event-transfer enable action-manifest install default ! activity core-transfer enable ! contact-company name Dell street-address F lane , Sector 30 address city Brussels state HeadState country Belgium postalcode S328J3 ! contact-person first Fred last Nash email-address primary des@sed.com alternate sed@dol.
2016 09:43:56 IST event-transfer 2016 09:48:21 IST full-transfer 2016 09:38:27 IST DellEMC# 1658 SupportAssist Success Feb 15 2016 09:47:43 IST Feb 15 Success Feb 15 2016 09:36:12 IST Feb 15
60 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
Defaults end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year.
start-week (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: ● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month. ● last: Enter this keyword to start daylight saving time in the last week of the month.
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key. ● clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis.
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option.
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
Version Description 9.2(1.0) Introduced on the Z9500. ntp offset-threshold Configure the threshold time interval before which the system generates an NTP audit log message if the time difference from the NTP server is greater than a threshold value (offset-threshold). Syntax ntp offset-threshold threshold-value To disable the threshold value, use the no ntp offset-threshold command.
maxpoll polling- interval Defaults (OPTIONAL) Enter the keyword maxpollthen the polling-interval. The polling interval range is from 4 to 16. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) The trusted-key range value is increased from 1 to 65534.
(KoD) packet. When the Dell EMC Networking OS client receives KoD packets, it logs the following syslog message: Dell EMC# May 27 14:32:13 %STKUNIT1-:CP %ntp-6-: receive: KoD packet from 300::2 has inconsistent xmt/org/rec timestamps. Ignoring. Related Commands ● show ntp associations—displays the NTP servers that are configured and their status. ntp source Specify an interface’s IP address to be included in the NTP packets.
Version Description 8.5.1.0 Added support for 4-port 40G line cards. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp step-threshold Configure the step-threshold time interval. Syntax ntp step-threshold value To return to the default NTP step-threshold value, use the no ntp step-threshold command. Parameters Defaults value Enter the threshold value in milliseconds. The range is from 128 to 5000 milliseconds (5 seconds).
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
Example Example (Detail) Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC#show clock 11:05:56.949 UTC Thu Oct 25 2001 DellEMC# DellEMC# show clock detail 12:18:10.
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp associations command shown in the Example below. Field Description (none) One or more of the following symbols could be displayed: ● ● ● ● ● Example (without ntp master configuration) Example (with ntp master configuration) * means synchronized to this peer. # means almost synchronized to this peer.
Related Commands ● show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXECEXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
61 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
Usage Information The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000.
tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit value To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters Defaults value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64.
Defaults Tunnel keepalive is disabled. Command Modes INTERFACE TUNNEL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. To enable a tunnel interface, use this command.
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the tunnel source anylocal command. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. Added an optional keyword “anylocal” to the tunnel source command.
62 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
Related Commands ● clear ufd-disable — re-enable downstream interfaces that are in a UFD-Disabled Error state. description Enter a text description of an uplink-state group. Syntax description text Parameters Defaults text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific.
Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. If a 40G port is fanned-out into 10G ports, the range is entered as slot/sort/ subport-slot/port/subport. Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific.
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
Usage Information When one upstream interface in an uplink-state group goes down, you can configure the number of downstream interfaces in an uplink-state group are put into a link-down state with an UFD-Disabled error message. If all upstream interfaces in an uplink-state group go down, all downstream interfaces in the same uplinkstate group are put into a link-down state. Related Commands ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface.
Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
Example Version Description 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
Uplink State Group : 1 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/25(Up) Te 1/28(Up) Downstream Interfaces : Te 5/1(Up) Te 5/1(Up) Te 5/3(Up) Te 5/5(Up) Te 5/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 1/1(Dwn) Te 1/3(Dwn) Te 1/5(Dwn) Downstream Interfaces : Te 5/2(Dis) Te 5/4(Dis) Te 5/11(Dis) Te 5/12(Dis) Te 5/13(Dis) Te 5/14(Dis) Te 5/15(Dis) Uplink State Group : 6 Status: Enabled,
Usage Information After you enter the command, to assign upstream and downstream interfaces to the group, enter UplinkState-Group Configuration mode. An uplink-state group is considered operationally up if at least one upstream interface in the group is in the Link-Up state. An uplink-state group is considered operationally down if no upstream interfaces in the group are in the Link-Up state. No uplink-state tracking is performed when a group is disabled or in an operationally down state.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. You can assign physical port or port-channel interfaces to an uplink-state group. You can assign an interface to only one uplink-state group.
63 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. When packets are colored green; no packets are dropped.
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. S4048–ON Syntax Parameters Defaults dei mark {green | yellow} {0 | 1} 0|1 Enter the bit value you want to map to a color. green | red | yellow Choose a color: ● Green: High priority packets that are the least preferred to be dropped.
member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command. Parameters interface Enter the following keywords and the interface information: ● For a Port Channel interface, enter the keywords port-channel, and then a number.
Parameters unit-id Enter the stack unit ID. stack-group-id Enter the stack group ID. The range is from 0 to 16. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to enabling this command, to place the interface in Layer 2 mode, enter the switchport command.
Version Description E-Series original Command Usage Information Prior to disabling the stackable VLAN feature, remove the members. To view the stackable VLANs, use the show vlan command in EXEC Privilege mode. Stackable VLANs contain members, designated by the M in the Q column of the command output. If you enabled VRF, you cannot enable the stacked VLAN feature using this command. If you enabled IGMP snooping, you cannot enable the stacked VLAN feature using this command.
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. You can separate the C-Tag values by commas or dashed ranges. In the case of conflicts, dynamic mode CoS overrides any Layer 2 QoS configuration.
Usage Information For specific interoperability limitations regarding the S-Tag TPID, see the Dell EMC Networking OS Configuration Guide. The four characters you may enter are shown in the following table. Related Commands Number Resulting TPID 1 0x0001 10 0x0010 81 0x0081 8100 0x8100 ● portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays.
Version Description 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, use the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. In Example 1, a VLAN-Stack trunk port is configured and then made part of a single-tagged VLAN.
DellEMC(conf-if-te-5/1)# switchport DellEMC(conf-if-te-5/1)# vlan-stack trunk DellEMC(conf-if-te-5/1)# exit DellEMC(config)# interface vlan 10 DellEMC(conf-if-vlan)# vlan-stack compatible DellEMC(conf-if-vlan)# member Te 4/1, Te 3/10, TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# interface vlan 30 DellEMC(conf-if-vlan)# untagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# DellEMC(config)# interface vlan 40 DellEMC(conf-if-vlan)# tagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config
64 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • ip vrf ip http vrf description ip vrf forwarding ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip vrf Create or delete a customer VRF.
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
you assign two interfaces to the same VRF, you cannot configure overlapping IP subnets or the same IP address to them. Example DellEMC# configure terminal DellEMC(conf)# ip vrf red DellEMC(conf-vrf)# description "Red Network" DellEMC(conf-vrf)# show config ! ip vrf red 4 description "Red Network" DellEMC(conf-vrf)# DellEMC(conf-if-te-1/45)# int te 7/46 DellEMC(conf-if-te-1/46)# no shut DellEMC(conf-if-te-1/46)# ip vrf forwarding red DellEMC(conf-if-te-1/46)# ip add 100.1.1.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, you can use the ip route-export tag command without specifying the route-map attribute. This action exposes source VRF routes to various other VRFs, which then import these routes using the ip route-import tag command.
Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. ● ip route-export – exports routes to another VRF. ipv6 route-export Enables route leaking between VRFs.
Only active routes are eligible for leaking. For example, if one VRF has two routes corresponding to BGP and OSPF, in which the BGP route is not active, the OSPF route takes precedence over BGP. Even though the target VRF has specified filtering options to match BGP, the BGP route is not leaked as that route is not active in the source VRF. Related Commands ● ipv6 route-import – imports IPv6 routes from another VRF.
Parameters bgp Enter the keyword bgp to leak or share routes corresponding to the BGP protocol. isis Enter the keyword isis to leak or share routes corresponding to the ISIS protocol. ospf Enter the keyword ospf to leak or share routes corresponding to the OSPF protocol. connected Enter the keyword connected to leak or share connected routes corresponding to the VRF. static Enter the keyword static to leak or share static routes corresponding to the VRF.
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. ● ip route-import — import routes from another VRF.
To remove the limit on the maximum number of routes used, use the no maximum dynamic-routes command. Parameters limit Maximum number of routes allowed in a VRF. The valid range is from 1 to 16,000 (or maximum allowable for that platform if a smaller value). warningthreshold The warning threshold value is a percentage of the limit value. When the number of routes reaches the specified percentage of the limit, a warning message appears. The valid range is from 1 to 100.
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. This command displays information from the running-config corresponding to either a specific VRF or all the VRFs in the system.
65 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
Usage Information Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link.
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. S4048–ON Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
66 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
arp additional-refresh Perform additional ARP refresh on the VLTi (ICL). Syntax arp additional-refresh To disable additional ARP refresh on VLTi, use the no arp additional-refresh command. Defaults Enabled Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(2.7) Introduced on all platforms.
Example Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.2(0.2) Added support for IPv6. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
Example Related Commands Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.2(0.2) Added multicast and ndp parameters. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
Usage Information Version Description 8.3.19.0 Introduced on the S8420T. 8.3.12.0 Introduced on the S4810. To delay the system from bringing up the VLT port for a brief period to allow IGMP snooping and Layer 3 routing protocols to converge, use the delay-restore command. Use this command: ● after a VLT device reloads. ● if the peer VLT device was up at the time the VLTi link failed. Related Commands ● show vlt statistics — displays statistics on VLT operations.
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
To disable this feature on VLT and port channels, use no lacp ungroup member-independent {vlt | port-channel} command under the configuration mode. Example DellEMC(conf)#lacp ungroup member-independent ? port-channel LACP port-channel members become switchports vlt All VLT LACP members become switchports multicast peer-routing timeout To retain synced multicast routes or synced multicast outgoing interface (OIF) after a VLT peer node failure, configure the timeout value for a VLT node.
Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the support for IPV6 / IPV4. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4.
primary-priority Assign the priority for master election among VLT peers. Syntax Parameters Default [no] primary-priority value To configure the primary role on a VLT peer, enter a lower value than the priority value of the remote peer. The range is from 1 to 65535. The default value is 32768. 32768 Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific.
Usage Information Example (Brief) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
show vlt detail Displays detailed status information about VLT domains configured on the switch. Syntax show vlt detail Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. DellEMC#show vlt inconsistency ip mroute Spanned Multicast Routing IIF Inconsistency Multicast Route LocalIIF -----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.
Vlan-config --------------------------------Vlan-ID Local Mode Peer Mode --------- ------------ --------20 L2 -- Vlan IPV4 Multicast Status -------------------------Vlan-ID Local Status ------------------55 Inactive 1500 Inactive Peer Status ----------Active Active VLT-VXLAN config --------------- - VLAN to VNI config mismatch -------------------------------------Vlan-ID Local VNID Peer VNID -----------------------------10 10 11 11 12 12 13 13 VXLAN enabled status on VLT Port Channels -------------
Port-type-config ---------------Codes:: p - PVLAN Promiscuous port, h - PVLAN Host port, t - PVLAN Trunk port, mt - Vlan-stack trunk port, mu - Vlan-stack access port, n Normal port Vlt Lag ------128 Local ----mt Peer ---mu Vlan-stack protocol-type -----------------------Local ----0x4100 Peer ---0x8100 VLT-VLAN config --------------Local Lag --------128 Peer Lag Local VLANs -------- ----------128 4094 Peer VLANs ---------100 DellEMC# show vlt role Displays the VLT peer status, role of the local VLT
Example Dell_VLTpeer1# show vlt role VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Primary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:bc 32768 Dell_VLTpeer2# show vlt role VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 show vlt statistics Displays VLT operations statistics.
Related Commands Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support in the output for ARP, MAC, and IGMP snooping. 8.3.8.0 Introduced on the S4810. ● clear vlt statistics — clears the statistics on VLT operations. NOTE: The following example shows the statistics for all the VLT parameters. If you enter a specific keyword, such as mac, only the statistics for that VLT parameter displays.
show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, the Dell EMC Networking OS automatically creates a VLTsystem MAC address used for internal system operations.
This command minimizes the time required for the VLT system to determine the unit ID assigned to each peer switch when one peer reboots. vlt domain Enable VLT on a switch, configure a VLT domain, and enter VLT-Domain Configuration mode. Syntax Parameters vlt domain domain-id domain-id Enter the domain ID number. Configure the same domain ID on the peer switch. The range of domain IDs is from 1 to 1000. Command Modes CONFIGURATION Command History This guide is platform-specific.
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.
30 (I) 40 50(C) 60 (I) V T T T Virtual Link Trunking (VLT) 1749
67 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
all Enter the keyword all to clear both MAC address of the VXLAN and legacy VLAN. interface Enter the keyword interface to clear MAC address from a specific interface. vlan Enter the keyword vlan to clear MAC address from a specific vlan. vxlan Enter the keyword vxlan to clear MAC address from a specific vxlan. Command Modes EXEC Privilege Command History This guide is platform-specific.
Defaults tcp (OPTIONAL) Enter the keyword tcp to configure tcp connection to controller. ssl (OPTIONAL) Enter the keyword ssl to configure ssl connection to controller (Default). Disabled Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
debug vxlan Debug messages between the Gateway and Controller. Syntax debug vxlan Defaults Disabled Command Modes EXEC Privilege Command History Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S6000.
fail-mode Configures failure-mode on the platform. Syntax fail-mode secure To disable the fail-mode secure, use the no fail-mode securecommand. Parameters Defaults secure Enter the keyword secure to delete all its database and hardware flows/ resources, when the VTEP loses connectivity with the controller. non secure Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific.
local-vtep-ip Set the local IP Address to be used as the source IP for VXLAN tunnels. Syntax local-vtep-ip IP Address To disable the settings, use the no local-vtep-ip command. Parameters Defaults IP Address Enter the local IP Address to be used as a source for VXLAN tunnels. None. Command Modes VXLAN INSTANCE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
peer-ovsdbserver-ip Specify the IP address of the peer OVSDB server in a VLT setup. Syntax peer-ovsdbserver-ip peer-ip-address To remove the configuration, use the no peer-ovsdbserver-ip Parameters Defaults peer-ip-address Enter the peer OVSDB server IP address. This is usually the management IP address of the peer VLT device. Not configured Command Modes VXLAN-INSTANCE Command History This guide is platform-specific.
Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile. The range is from 1 to 16777215. None. Command Modes VNI-PROFILE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON.
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced nsx and Nuage keywords on the S5048F–ON. 9.13(0.0) Introduced nsx and Nuage keywords on the S4048–ON, S4048T-ON, S6000, S6000–ON, S6100–ON, S6010–ON, and Z9100–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.
Version Description 9.8(0.0) Introduced on the S4048–ON. 9.4(0.0) Introduced on the S6000. Usage Information You must disable vxlan-instance before unconfiguring VAP. Related Commands feature vxlan — Enable VXLAN configuration globally on the platform. vxlan-instance loopback Provision VXLAN and non-VXLAN loopback ports that support routing in and out of VXLAN tunnels and enable MAC level loopback on all these ports.
vnid Associate a range of VNID numbers to a specific VNI profile. Syntax vnid VNID-Range To remove the association, use the no vnid command. Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile. The range is from 1 to 16777215. None. Command Modes VNI-PROFILE Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
Parameters Defaults instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. static Enter the keyword static to set the VXLAN instance in static mode. Controller mode. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
show running-config vxlan Displays the VXLAN configuration information from running configuration. Syntax show running-config vxlan Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.
Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
Example Related Commands Version Description 9.4.(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) vxlan-instance — Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics interface Displays the port VLAN statistics information related to Network Virtualization Overlay (NVO) Gateway.
Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics remote-vtep-ip Displays VXLAN statistics for a specific VXLAN tunnel. Syntax show vxlan vxlan-instance instance ID statistics remote-vtep-ip IP Address Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. remote-vtep-ip Enter the keyword remote-vtep-ip followed by the IP Address of the remote VTEP.
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show VLT peer’s local macs. 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. Introduced on the Z9100–ON. Example Related Commands 9.
Example Related Commands Version Description 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 unicast-mac-remote Total Remote Mac Count: 1 VNI MAC TUNNEL 100 00:00:07:00:02:00 (N) 60.1.1.1 vxlan-instance- Enable VXLAN Instance configuration on the platform.
68 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax Parameters clear counters vrrp [vrrp-id] [ipv6] vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups.
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group. Syntax description text To delete a VRRP group description, use the no description command. Parameters Defaults text Enter a text string up to 80 characters long.
To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command.
If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration. Syntax Parameters show config [verbose] verbose (OPTIONAL) Enter the keyword verbose to view all the VRRP group configuration information, including default information. Command Modes VRRP Command History Example This guide is platform-specific.
Parameters vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups. interface type (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
Item Description Pre States whether preempt is enabled on the interface: ● Y = Preempt is enabled. ● N = Preempt is not enabled. State Displays the operational state of the interface using one of the following: ● NA/IF (the interface is not available). ● MASTER (the interface associated with the MASTER router). ● BACKUP (the interface associated with the BACKUP router). Example (Brief) Usage Information Master addr Displays the IP address of the MASTER router.
Item Description ● Dn or Up states whether the interface is down or up. ● The interface type slot/port information. Example Example (VRRP VRF) DellEMC> show vrrp -----------------TenGigabitEthernet 1/3, VRID: 1, Net: 10.1.1.253 VRF: 0 default State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
-------------------------------------------------------------------Fo 1/50 IPv4 20 100 Y Master 10.0.0.3 10.0.0.2 DellEMC# track Monitor an interface and lower the priority value of the VRRP group on that interface if it is disabled. Syntax track interface [priority-cost cost] To disable monitoring, use the no track interface command.
To delete one or more virtual IP addresses, use the no virtual-address ip-address1 [... ip-address12] command. Parameters Defaults ip-address1 Enter an IP address of the virtual router in dotted decimal format. The IP address must be on the same subnet as the interface’s primary IP address. ... ip-address12 (OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted decimal format. Separate the IP addresses with a space.
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. This command applies to all the VRRP interfaces on a system. When you use this command with the vrrp delay minimum command, the later timer rules VRRP enabling.
Related Command ● virtual-address — assigns up to 12 virtual IP addresses per VRRP group. version Set the VRRP protocol version for the IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters Defaults 2 Enter the keyword 2 to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the keyword 3 to specify VRRP version 3 as defined by RFC 5798, Virtual Router Redundancy Protocol.
IPv6 VRRP Commands The following are IPv6 VRRP commands. ● ● ● ● clear counters vrrp ipv6 debug vrrp ipv6 show vrrp ipv6 vrrp-ipv6-group The following commands apply to IPv4 and IPv6: ● ● ● ● ● ● ● ● advertise-interval description disable hold-time preempt priority show config virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups.
Usage Information NOTE: You can also clear the port configurations corresponding to a range of ports. For Open Networking (ON) platforms, the notation for specifying the port range in the command is different from how you specify the port range in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range.
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series, C-Series, and S-Series. Support was added for IPv6 VRRP groups in nondefault VRF instances. 8.3.2.0 Introduced on the E-Series. If you do not specify an option, debugging is active on all interfaces and all VRRP groups. show vrrp ipv6 View the active IPv6 VRRP groups.
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.3.2.0 Introduced on the E-Series. The following describes the show vrrp ipv6 command. Line starting with Description GigabitEthernet.. Displays the interface, VRRP group ID, and network address. If the interface is not . sending VRRP packets, 0.0.0.0 appears as the network IP address. VRF VRF instance to which the VRRP group interface belongs. State: master...
vrrp-ipv6-group Assign an interface to a VRRP group. Syntax vrrp-ipv6-group vrid Parameters Defaults vrid Enter the virtual-router ID number of the VRRP group. The VRID range is from 1 to 255. Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
69 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax crypto ca-cert install path Parameters path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
● sysadmin ● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
device. If the Common Name does not match the device’s presented identity, then even a properly signed certificate does not validate correctly. email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect.
crypto cert install Installs a trusted certificate on a device. Syntax Parameters crypto cert install cert-file cert-path key-file {key-path | private} [password passphrase] cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored.
certificate. If the system is in non-FIPS mode, the certificate is installed as the non-FIPS certificate. When FIPS mode is enabled or disabled, the certificates (and keys) are switched by the system. NOTE: For the switch, there are two possible certificates stored - one for FIPS mode, one for nonFIPS mode. If the system is in FIPS mode, the certificate will be installed as the FIPS certificate. If the system is in non-FIPS mode, the certificate will be installed as the non-FIPS certificate.
Defaults accept Enter the keyword accept to accept the presented certificate and log in if OCSP retrieval fails. reject Enter the keyword reject to reject the presented certificate and log in if OCSP retrieval fails. crypto x509 revocation ocsp accept Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
Parameters hostname Enter the name of the host or device for which you wish to record logs corresponding to the certificates. NOTE: The hostname can be an IPV4 address, an IPV6 address, or a DNS hostname—with or without DNS suffix. secure Enter the keyword secure to enable the Syslog feature to communicate with a compatible Syslog server using the secure TLS protocol over the default port (6514). The range is from 1024 to 65535. tcp Enter the keyword tcp to enable TCP.
NOTE: To get the subject key identifier details, enter the show crypto cacert command. This command displays the CA certificate details. Defaults None. Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Usage Information Version Description 9.11.0.
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin Multiple OCSP responders may be configured per CA. The system tries each one until it gets a valid response. No priority may be specified or guaranteed; the system tries them in the order in which they were configured. Related Commands ● crypto x509 ocsp ocsp-server prefer Configures OCSP responder preference.
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin This show command should display the index, the certificate’s subject field in plaintext, not-before and not-after dates, and the fingerprint in hexadecimal format. The index assigned to each CA certificate is used by the crypto cert delete certificate-authority command to allow the user to specify which certificate authority to remove.