Deployment Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Table Of Contents

Dell Command Line Reference Guide for the

S6100–ON System

9.14.2.5

January 2020

Rev. A00

Summary of content (1713 pages)

PAGE 1
Dell Command Line Reference Guide for the S6100–ON System 9.14.2.5 January 2020 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 - 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide.........................................................................................................40 Objectives........................................................................................................................................................................... 40 Audience..............................................................................................................................................................................
PAGE 4
banner login........................................................................................................................................................................ 85 banner motd........................................................................................................................................................................87 boot-type.........................................................................................................................................
PAGE 5
show reset-reason...........................................................................................................................................................140 show software ifm...........................................................................................................................................................142 show system.....................................................................................................................................................
PAGE 6
feature acloptimized................................................................................................................................................. 186 feature aclrange......................................................................................................................................................... 187 ip access-group.........................................................................................................................................................
PAGE 7
clear ip prefix-list.......................................................................................................................................................249 deny..............................................................................................................................................................................250 ip prefix-list.............................................................................................................................................
PAGE 8
permit tcp (for Extended IP ACLs)............................................................................................................................ 300 seq arp (for Extended MAC ACLs)............................................................................................................................. 301 seq ether-type (for Extended MAC ACLs).............................................................................................................. 302 seq (for IP ACLs)...................
PAGE 9
bgp dmzlink-bw......................................................................................................................................................... 354 bgp enforce-first-as................................................................................................................................................. 354 bgp fast-external-fallover.......................................................................................................................................
PAGE 10
neighbor update-source.......................................................................................................................................... 400 neighbor weight.........................................................................................................................................................400 network........................................................................................................................................................................
PAGE 11
show cam-usage............................................................................................................................................................. 456 test cam-usage................................................................................................................................................................458 Unified Forwarding Table Modes................................................................................................................................
PAGE 12
dcb-map............................................................................................................................................................................ 493 priority-pgid...................................................................................................................................................................... 493 priority-group bandwidth pfc....................................................................................................................
PAGE 13
excluded-address...................................................................................................................................................... 539 hardware-address..................................................................................................................................................... 540 host-address..............................................................................................................................................................
PAGE 14
hash-algorithm.................................................................................................................................................................575 ip ecmp-group..................................................................................................................................................................578 ip ecmp weighted..........................................................................................................................................
PAGE 15
disable.................................................................................................................................................................................616 garp timers........................................................................................................................................................................ 616 gvrp enable.................................................................................................................................
PAGE 16
flowcontrol..................................................................................................................................................................660 interface...................................................................................................................................................................... 663 interface group............................................................................................................................................
PAGE 17
Chapter 22: IPv4 Routing...........................................................................................................727 arp....................................................................................................................................................................................... 728 arp backoff-time..............................................................................................................................................................
PAGE 18
show show show show show show ip protocols............................................................................................................................................................ 780 ip route....................................................................................................................................................................782 ip route list.......................................................................................................................
PAGE 19
domain-password............................................................................................................................................................829 graceful-restart ietf........................................................................................................................................................829 graceful-restart interval.......................................................................................................................................
PAGE 20
advertise dcbx-app-tlv.................................................................................................................................................. 875 iscsi aging time................................................................................................................................................................ 876 iscsi cos.....................................................................................................................................................
PAGE 21
fefd disable.................................................................................................................................................................. 916 fefd interval................................................................................................................................................................. 917 fefd mode.................................................................................................................................................
PAGE 22
ip msdp mesh-group.......................................................................................................................................................957 ip msdp originator-id...................................................................................................................................................... 958 ip msdp peer.......................................................................................................................................................
PAGE 23
tc-flush-standard............................................................................................................................................................ 992 Chapter 34: Multicast................................................................................................................994 IPv4 Multicast Commands............................................................................................................................................994 clear ip mroute...............
PAGE 24
show track.................................................................................................................................................................1028 threshold metric.......................................................................................................................................................1030 track interface ip routing........................................................................................................................................
PAGE 25
maximum-paths........................................................................................................................................................1075 mib-binding................................................................................................................................................................1075 network area..........................................................................................................................................................
PAGE 26
ipv6 ospf graceful-restart helper-reject............................................................................................................. 1136 ipv6 ospf hello-interval............................................................................................................................................1137 ipv6 ospf priority......................................................................................................................................................
PAGE 27
show ip pim ssm-range........................................................................................................................................... 1185 show ip pim summary.............................................................................................................................................. 1186 show ip pim tib..........................................................................................................................................................
PAGE 28
tc-flush-standard...........................................................................................................................................................1227 vlan bridge-priority........................................................................................................................................................ 1227 vlan forward-delay...........................................................................................................................................
PAGE 29
show qos wred-profile.............................................................................................................................................1271 service-class buffer shared-threshold-weight................................................................................................. 1272 test cam-usage.........................................................................................................................................................1273 threshold.................
PAGE 30
Chapter 45: Remote Monitoring (RMON)................................................................................. 1315 rmon alarm....................................................................................................................................................................... 1315 rmon collection history..................................................................................................................................................1317 rmon collection statistics......
PAGE 31
access-class..............................................................................................................................................................1357 enable password...................................................................................................................................................... 1358 enable restricted.....................................................................................................................................................
PAGE 32
dot1x mac-auth-bypass..........................................................................................................................................1396 dot1x max-eap-req.................................................................................................................................................. 1397 dot1x port-control...................................................................................................................................................
PAGE 33
show userroles..........................................................................................................................................................1437 userrole...................................................................................................................................................................... 1438 ICMP Vulnerabilities...........................................................................................................................................
PAGE 34
snmp-server trap-source....................................................................................................................................... 1478 snmp-server user.....................................................................................................................................................1480 snmp-server user (for AES128-CFB Encryption)............................................................................................ 1482 snmp-server view....................
PAGE 35
storm-control storm-control storm-control storm-control storm-control broadcast (Interface)........................................................................................................................ 1538 multicast (Configuration)................................................................................................................. 1539 multicast (Interface)..........................................................................................................................
PAGE 36
url................................................................................................................................................................................. 1571 show eula-consent........................................................................................................................................................ 1572 show running-config....................................................................................................................................
PAGE 37
tunnel source..................................................................................................................................................................1609 Chapter 58: VLAN Stacking.......................................................................................................1611 dei enable.......................................................................................................................................................................... 1611 dei honor....
PAGE 38
peer-routing-timeout....................................................................................................................................................1648 primary-priority.............................................................................................................................................................. 1648 show vlt brief.................................................................................................................................................
PAGE 39
clear counters vrrp..................................................................................................................................................1682 debug vrrp................................................................................................................................................................. 1683 description..........................................................................................................................................................
PAGE 40
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 41
Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
PAGE 42
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 43
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 44
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/11/1 for the interface tengigabitethernet 1/1/11/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
PAGE 45
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
PAGE 46
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
PAGE 47
show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated the command to display the IPV6acloptimized feature on the S6100– ON and Z9100–ON. 9.12(1.
PAGE 48
CLASS-MAP Mode To create or configure a class map, use CLASS-MAP mode. For more information, see Policy-Based QoS Commands. To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command.
PAGE 49
2. Enter the ecmp-group command then enter the ECMP group ID. The prompt changes to include conf-ecmp-groupecmp-group-id. You can return to CONFIGURATION mode by using the exit command. EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command.
PAGE 50
To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port[/subport] number.
PAGE 51
ISIS ADDRESS-FAMILY Mode To enable or configure IPv6 for ISIS, use ISIS ADDRESS-FAMILY mode. For more information, see Intermediate System to Intermediate System (IS-IS). To enter ISIS ADDRESS-FAMILY mode: 1. Verify that you are logged in to ROUTER ISIS mode. 2. Enter the address-family ipv6 unicast command. The prompt changes to include conf-router_isisaf_ipv6. LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode.
PAGE 52
2. Enter the monitor session command, and then the session ID. The prompt changes to include conf-mon-sesssessionID. MULTIPLE SPANNING TREE (MSTP) Mode To enable and configure MSTP, use MULTIPLE SPANNING TREE mode. For more information, see Multiple Spanning Tree Protocol (MSTP). To enter MULTIPLE SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree mstp command. The prompt changes to include conf-mstp.
PAGE 53
PROTOCOL GVRP Mode To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For more information, see GARP VLAN Registration (GVRP). To enter PROTOCOL GVRP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol gvrp command. The prompt changes to include config-gvrp. You can return to CONFIGURATION mode by using the exit command. RAPID SPANNING TREE (RSTP) Mode To enable and configure RSTP, use RSTP mode.
PAGE 54
You can switch to INTERFACE mode by using the interface command or you can switch to ROUTER RIP mode by using the router rip command. ROUTER OSPFV3 Mode To configure OSPF for IPv6, use ROUTER OSPFV3 mode. To enter ROUTER OSPFV3 mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ipv6 router ospf {process-id} command. The prompt changes to include conf-ipv6-router_ospf. You can return to CONFIGURATION mode by using the exit command.
PAGE 55
2. Enter the vlt domain command, and then the VLT domain number. The prompt changes to include conf-vlt-domain. You can return to CONFIGURATION mode by entering the exit command. VRRP Mode To enable and configure Virtual Router Redundancy Protocol (VRRP), use VRRP mode. For more information, see Virtual Router Redundancy Protocol (VRRP). To enter VRRP mode: 1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command, and then enter the VRRP group ID.
PAGE 56
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 57
secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system. nfsmount://filepath system: Enter the keyword system: to retrieve the image from the system. usbflash Enter the keyword usbflash: to retrieve the image from the USB flash memory. usbflash://filename.
PAGE 58
usbflash: Use the keyword usbflash: to change the current directory to the inserted USB. directory name and path Enter the directory name and path as follows: directory name ([[flash://]directory_path]) NOTE: The cd command without any arguments will change the current directory to flash: Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 59
scp: Enter the keyword scp: to copy from the remote file system, IPv4, or IPv6, (scp://userid:password@hostip/filepath). startup-config Enter the keywords startup-config to copy from the startup configuration. tftp: Enter the keyword tftp: to copy from the remote file system, IPv4, or IPv6, (tftp://hostip/filepath). usbflash: Enter the keyword usbflash: to copy the file to or from the external USB flash.
PAGE 60
When you load the startup configuration or a configuration file from a network server such as TFTP to the running configuration, the configuration is added to the running configuration. This does not replace the existing running configuration. Commands in the configuration file has precedence over commands in the running configuration. Dell EMC Networking OS supports copying the running-configuration to a TFTP server, an FTP server, or a remote NFS file system.
PAGE 61
Related Commands ● cd – changes the working directory. delete Delete a file from the flash. After deletion, files cannot be restored. Syntax Parameters delete {flash: | nfsmount: | usbflash:} [no-confirm] flash: To delete a file or directory on the internal flash, enter flash:// then the filename or directory name ([flash://]filepath). nfsmount: To delete a file or directory on the NFS-mounted file system, enter nfsmount:// then the mount point and the file path (nfsmount://filepath).
PAGE 62
Parameters flash: For a directory on the internal Flash, enter flash:// directory name. nfsmount: For a file or directory on an NFS-mounted file system, enter nfsmount:// then the mount point and file path. NOTE: While displaying a file directory on a remote NFS file system, it is mandatory to specify the mount-point that indicates the working directory on the NFS file system. You cannot display details corresponding to the root directory of the remote NFS file system.
PAGE 63
nfsmount: 1463410688 bytes total (585719808 bytes free) DellEMC# Related Commands ● cd — changes the working directory. format Erase all existing files and reformat the file system. After the file system is formatted, files cannot be restored. Syntax format {flash: | usbflash:} Defaults None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 64
usbflash: Defaults For a directory on the external USB flash, enter usbflash:// directory name. None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 65
Example Related Commands Version Description 9.7(0.0) Introduced on the S-Series. DellEMC# mkdir nfsmount:/nfs-mountpoint/guest DellEMC# ● rmdir — remove a directory. mount nfs Mounts an NFS file system to a device. Syntax mount nfs rhost:path mount-point [username password] Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system.
PAGE 66
Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 67
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Enhanced to specify the MD5, SHA1, or SHA256 hash of the OS image that the system uses to validate the image during reboot. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 68
○ ip ecmp-group maximum-paths 2-64 ● ACL CAM carving related CLIs: ○ cam-acl cli ○ cam-acl-vlan cli ○ cam-acl-egress cli ○ cam-sharing ● Feature keyword CLIs: ○ feature udf-acl ○ feature aclrange ○ feature ipv6acloptimized ○ feature acloptimized Example DellEMC# upgrade system tftp://10.11.8.12/dv-rainier-13 a: 00:39:32 : Discarded 1 pkts. Expected block num : 51. Received block num: 50 !00:39:36 : Discarded 1 pkts. Expected block num : 65.
PAGE 69
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.1.
PAGE 70
Example DellEMC#show boot system stack-unit 1 Current system image information in the system: =============================================== Type Boot Type A B ---------------------------------------------------stack-unit 1 FLASH BOOT 9.10(0.0) 9.10(0.0) [boot] DellEMC# show bootvar Display the variable settings for the boot parameters. Syntax show bootvar Command Modes EXEC Privilege Command History Example 70 This guide is platform-specific.
PAGE 71
show file-systems Display information about the file systems on the system. Syntax show file-systems Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 72
Field Description Prefixes Displays the name of the storage location. show os-version Display the release and software image version information of the image file specified. Syntax show os-version [file-url] Parameters Defaults file-url (OPTIONAL) Enter the following location keywords and information: ● For a file on the internal flash, enter flash:// followed by the filename. ● For a file on an FTP server, enter ftp://user:password@hostip/ filepath.
PAGE 73
runtime 9.10(0.0) Control Processor passed BOOT IMAGE INFORMATION : -------------------------------------------------Type Version Target checksum boot flash 3.25.2.2 Control Processor passed BOOTSEL IMAGE INFORMATION : ----------------------------------------------------Type Version Target checksum boot selector 3.25.0.
PAGE 74
File Management frrp for the current FRRP configuration fvrp for the current FVRP configuration gvrp for the current GVRP configuration host for the current host configuration hardwaremonitor for hardware-monitor action-on-error settings hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current interface configuration interface port-channel for the current port-channel interface configuration.
PAGE 75
qos-policyoutput for the current output QoS policy configuration radius for the current RADIUS configuration redirect-list for the current redirect-list configuration redundancy for the current RPM redundancy configuration resolve for the current DNS configuration rip for the current RIP configuration rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configuration snmp for the current SNMP configuration spanning-tree fo
PAGE 76
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for the tunnel and EIS interface types. 9.0.0.0 Added support for the VLT option. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the hardware-monitor option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 77
! Example Usage Information mtu 9416 portmode hybrid switchport rate-interval 5 service-policy input PMAP_INPUT dcb-policy buffer-threshold dcb-buff-threshold pfc priority 2-3 no shutdown DellEMC# show running-config status running-config bytes 10257, checksum 0xFD33339F startup-config bytes 10257, checksum 0xFD33339F The status option allows you to display the size and checksum of the running configuration and the startup configuration. show startup-config Display the startup configuration.
PAGE 78
boot system stack-unit 1 secondary system: B: boot system stack-unit 1 default system: A: ! redundancy auto-synchronize full ! hardware watchdog stack-unit 1 ! service timestamps log datetime ! Related Commands ● show running-config – displays the current (running) configuration. show version Display the current Dell EMC Networking Operating System (OS) version information on the system.
PAGE 79
Example (S6100– ON) Lines Beginning With Description Copyright (c)... Copyright information Build Time... Software build’s date stamp Build Path... Location of the software build files loaded on the system Dell EMC Networking OS uptime is... Amount of time the system has been up System image... Image file name System Type: System name Control Processor:... Control processor information and amount of memory on processor 8G Bytes ... Amount and type of memory on system 1 4 Modules...
PAGE 80
Defaults booted Enter the keyword booted to upgrade from the current image on the device. ftp: Enter the keyword ftp to follow it with the location of the source file in this form: //userid:password@hostip/filepath, or press Enter to launch a prompt sequence. tftp: Enter the keyword tftp to follow it with the location of the source file in this form: //hostlocation/filepath, or press Enter to launch a prompt sequence.
PAGE 81
Defaults flash:// (Optional). Enter the flash:// keyword. The default is to use the flash drive. You can just enter the image file name. img-file Enter the name the Dell EMC Networking software image file to validate. hash-value (Optional). Enter the relevant hash published on i-Support. flash drive Command Modes EXEC mode Command History Usage Information Version 9.5.(0.0) Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 82
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
PAGE 83
• • • • • • • • • • • • • • • • • • • • show inventory show login statistics show memory show processes cpu show processes ipc flow-control show processes memory show reload-type show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit stack-unit location-led telnet telnet-peer-stack-unit terminal length traceroute undebug all warmboot-failure-action write alias Configure shorter alias names for single-line command input.
PAGE 84
Example The following example shows how to configure single-line alias-name: DellEMC#configure terminal DellEMC(conf)# alias-definition DellEMC(conf-alias-definition)# alias showipbr10 show ip interface brief The following example shows how to configure aliases with arguments in EXEC mode: DellEMC#configure terminal DellEMC(conf)# alias-definition DellEMC(conf-alias-definition)# alias procpu show processes cpu management-unit | grep $1 DellEMC(conf-alias-definition)# alias intbr show ip interface brief | g
PAGE 85
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 86
Enter no banner login to delete the banner text. Enter no banner login keyboardinteractive to automatically go to the banner message prompt (does not require a carriage return). Parameters keyboardinteractive Enter the keyboard-interactive keyword and then press Enter (carriage return) to retrieve the message banner prompt. acknowledgemen Enter the acknowledgement keyword to require a positive acknowledgement t from the user while logging in to the system.
PAGE 87
If you configure the acknowledgement keyword, the system requires a positive acknowledgement from the user while logging in to the system. $ telnet 10.11.178.16 Trying 10.11.178.16... Connected to 10.11.178.16. Escape character is '^]'. THIS IS A LOGIN BANNER. PRESS ‘Y’ TO ACKNOWLEDGE. ACKNOWLEDGE? [y/n]: y Login: admin Password: Related Commands ● banner motd — sets a Message of the Day banner. ● banner exec — enables the display of a text string when you enter EXEC mode.
PAGE 88
Version Description E-Series Original command Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first. If no message of the day banner is configured, the login banner and prompt appear. After the user has logged in, the banner EXEC (if configured) displays.
PAGE 89
● ● ● ● ● ● ● ● ● ● cam-acl {default | l2acl number ipv4acl number ipv6acl number , ipv4qos number l2qos number l2pt numb er ipmacacl number ecfmacl number [vmanqos | vman-dualqos number } VmanQos : 0 EtsAcl : 0 FcoeAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 ipv4udfmirracl: 0 ipv4mirracl: 0 Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal to 9.
PAGE 90
When configuring space for IPv6 ACLs, the total number of Blocks must equal 9. The ipv6acl allocation must be a factor of 3 (0,3,6,9). If you enabled BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the reload conditional nvram-cfg-change command. clear average-power Reset the average power and average power start time.
PAGE 91
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 92
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode.
PAGE 93
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax Parameters Defaults do command command Enter an EXEC-level command.
PAGE 94
Example DellEMC(conf-if-te-1/1/1/1)# do clear counters Clear counters on all interfaces [confirm] DellEMC(conf-if-te-1/1/1/1)# DellEMC(conf-if-te-1/1/1/1)# do clear logging Clear logging buffer [confirm] DellEMC(conf-if-te-1/1/1/1)# DellEMC(conf-if-te-1/1/1/1)# do reload System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password.
PAGE 95
NOTE: If you are authorized for the EXEC Privilege mode by your role, you do not need to enter an enable password. Related Commands ● enable password — configures a password for the enable command and to access a privilege level. enable cpu-clock-monitor Enables Intel CPU LPC (Low Pin Count) clock-failure monitoring. Syntax enable cpu-clock-monitor To disable this feature, use the no enable cpu-clock-monitor command.
PAGE 96
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Replacement command for the S4820T. Replaces the enable xfp-powerupdates command. 8.3.11.4 Replacement command for the Z9000. Replaces the enable xfp-powerupdates command 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. To enable polling and to configure the polling frequency, use this command.
PAGE 97
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. E-Series Original command. ● exit — returns to the lower command mode. exec-timeout Set a time interval that the system waits for input on a line before disconnecting the session. Syntax exec-timeout minutes [seconds] To return to default settings, use the no exec-timeout command.
PAGE 98
Usage Information To remove the time interval, enter exec-timeout 0 0. Example Dell con0 is now available Press RETURN to get started. DellEMC> exit Return to the lower command mode.
PAGE 99
Related Commands Version Description E-Series Original command. ● end — returns to EXEC Privilege mode. ftp-server enable Enable FTP server functions on the system. Syntax Parameters Defaults ftp-server [vrf vrf-name] enable vrf vrf-name Enter the keyword vrf and then the name of the VRF to enable the FTP server to listen to that VRF instance. NOTE: Use this attribute to specify the VRF that is used by the FTP server to accept client connections.
PAGE 100
230 User logged in ftp> pwd 257 Current directory is "flash:" ftp> dir 200 Port set okay 150 Opening ASCII mode data connection size date time name -------- ------ ------ -------512 Jul-20-2004 18:15:00 tgtimg 512 Jul-20-2004 18:15:00 diagnostic 512 Jul-20-2004 18:15:00 other 512 Jul-20-2004 18:15:00 tgt 226 Transfer complete 329 bytes received in 0.018 seconds (17.95 Kbytes/s) ftp> ftp-server topdir Specify the top-level directory to be accessed when an incoming FTP connection request is made.
PAGE 101
Usage Information After you enable FTP server functions with the ftp-server enable command, Dell EMC Networking recommends specifying a top-level directory path. Without a top-level directory path specified, the Dell EMC Networking OS directs users to the flash directory when logging in to the FTP server. Related Commands ● ftp-server enable — enables FTP server functions on the E-Series. ● ftp-server username — sets a username and password for incoming FTP connections to the E-Series.
PAGE 102
hostname Set the host name of the system. Syntax hostname name Parameters Defaults name Enter a text string, up to 32 characters long. Dell Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 103
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 104
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 105
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 106
Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Configure a password with the ip ftp password command. Related Commands ● ip ftp password — sets the password for FTP connections. ip ftp vrf Configures an FTP client with a VRF that is used to connect to the FTP server.
PAGE 107
To disable the Telnet server, use the no ip telnet server enable command. Defaults Enabled Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 108
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 109
The following is a list of the Dell EMC Networking OS version history for this command. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 110
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. Usage Information Use this command to make the TFTP clients VRF aware. The VRF name that you specify is used by the TFTP client to reach the TFTP server. If no VRF is specified, then the default VRF is used.
PAGE 111
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command Usage Information You cannot delete a terminal connection. Related Commands ● access-class — restricts the incoming connections to a particular IP address in an IP access control list (ACL). ● password — specifies a password for users on terminal lines. logging disable-syslog snmp auth-failure Disable the generation of syslog messages for SNMP authentication failure events.
PAGE 112
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500.
PAGE 113
3 vty 1 10.14.1.97 4 vty 2 10.14.1.97 5 vty 3 10.14.1.97 Clear existing session? [line number/Enter to cancel]: Related Commands ● login statistics — enable and configure user login statistics on console and virtual terminal lines. ● show login statistics — displays login statistics of users who have used the console or virtual terminal lines to log in to the system. login statistics Enable and configure user login statistics on console and virtual terminal lines.
PAGE 114
Escape character is '^]'. Login: admin Password: Last successful login: 12:52:01 UTC Tue Mar 22 2016 Line vty0 ( 10.11.178.14 ). There were 1 unsuccessful login attempt(s) since the last successful login. There were 1 unsuccessful login attempt(s) for user admin in the last 30 day(s). There were 1 successful login attempt(s) for user admin in the last 30 day(s). The preceding message shows that the user had previously logged in to the system using the VTY line from 10.11.178.14.
PAGE 115
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command ping Test connectivity between the system and another device by sending echo requests and waiting for replies.
PAGE 116
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a Tunnel interface, enter the keyword tunnel then a number from 1 to 16383. Defaults tos (IPv4 only) Enter the type of service required. The range is from 0 to 255. The default is 0. df-bit (IPv4 only) Enter Y or N for the “don't fragment” bit in IPv4 header. ● N: Do not set the “don't fragment” bit.
PAGE 117
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0)P5 Introduced on the S4048–ON. 9.8(0.0)P2 Introduced on the S3048–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. Added support for the outgoing-interface option for link-local IPv6 addressing on the S4820T. Usage Information 8.3.12.
PAGE 118
Reply to Reply to Reply to :: Reply to Reply to Reply to DellEMC# Example (IPv6) request 1 from 172.31.1.208 0 ms request 1 from 172.31.1.216 0 ms request 1 from 172.31.1.205 16 ms request 5 from 172.31.1.209 0 ms request 5 from 172.31.1.66 0 ms request 5 from 172.31.1.87 0 ms DellEMC# ping 100::1 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds: !!!!! Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms) DellEMC# reload Reboot the system.
PAGE 119
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 9.1(0.0) Added ‘conditional’ parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you use only the reload command, the system boots into the Dell EMC Networking OS.
PAGE 120
Defaults normal-reload Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced on the S6000–ON, S6100–ON and Z9100–ON Once you enter reload-type, you need to enter the boot-type required on the next reboot.
PAGE 121
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. Messages can contain an unlimited number of lines; however, each line is limited to 255 characters. To move to the next line, use .
PAGE 122
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 123
showipbr10 show ip interface brief | …. showipbr40 show ip interface brief | …. shboot show bootvar… cr-vlan interface vlan $1 ..
PAGE 124
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 125
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series 6.2.1.1 Introduced on the E-Series.
PAGE 126
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 127
Command History Usage Information Example (all) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.1P1) The CLI has been enhanced to show the power, average power and average power start time. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 128
--------------------------------------------------------------------------------------1 32 36 32 38 34 34 31 53 30 DellEMC# DellEMC#show environment fan -- Fan Status -Unit Bay TrayStatus Fan1 Speed -----------------------------------------1 1 up up 7680 1 2 up up 7710 1 3 up up 7605 1 4 up up 7635 Speed in RPM DellEMC# DellEMC#show environment pem -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) Power AvgPower AvgPowerStartTime ----------------------------------------------------------------
PAGE 129
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.4 Output expanded to include Piece Part ID (PPID) and eSR4 optics. 8.3.11.
PAGE 130
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2/14 2/15 2/16 3/1 3/2 3/3 3/4 3/5 3/6 3/7 3/8 3/9 3/10 3/11 3/12 3/13 3/14 3/15 3/16 4/1 4/2 4/3 4/4 4/5 4/6 4/7 4/8 4/9 4/10 4/11 4/12 4/13 4/14 4/15 4/16 5/1 5/2 QSFP QSFP Media not present 40GBASE-CR4-1M 40GBASE-CR4-1M Media not present Media not present Media not present Media not present Media not present Media not present Media not present Media not present Media not present Media not present Media not present Media not pres
PAGE 131
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the successful-attempts keyword. Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500.
PAGE 132
User: admin2 Last login time: 12:49:27 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.145 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 3 Successful login attempt(s) in last 30 day(s): 2 ----------------------------------------------------------------------------------------------------------------------------------User: admin3 Last login time: 13:18:42 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 133
show memory View current memory usage on the switch. Syntax Parameters show memory [stack-unit id] stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack unit ID to display memory information on the designated stack member. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 134
stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack member ID. As an option of the show processes cpu command, this option displays CPU usage for the designated stack member. Or, as an option of the command, this option limits the output of memory statistics to the designated stack member. Refer to Example (stack-unit). summary (OPTIONAL) Enter the keywordsummary to view CPU utilization of processes related to stack-unit processing.
PAGE 135
ifagt_1 0xbb206020 tExcTask 0xba576020 envmgr 0xba592020 lcMgr 0xba5b3020 dla 0xba5d5020 sysAdmTsk 0xba5ee020 timerMgr 27380 2738 10000 1.00% 0.92% 1.07% 0 500 50 10000 0.00% 0.00% 0.00% 0 400 40 10000 0.00% 0.00% 0.00% 0 40 4 10000 0.00% 0.00% 0.00% 0 190 19 10000 0.00% 0.00% 0.00% 0 2730 273 10000 0.00% 0.00% 0.
PAGE 136
0x000003a5 clish 0x000001ad lacp 0x000004ba clish 0x000000c9 nvmgr 0x000000e0 igmp 0x00000132 vrrp 0x0000028d ovsdbsvr 0x000000a9 arpm 0x00000253 otm 0x00000206 tnlmgr 0x00000012 mount_mfs 0x0000024d xstp DellEMC# Related Commands 860 86 10000 0.40% 0.22% 0.28% 0 520 52 10000 0.20% 0.30% 0.16% 0 330 33 10000 0.20% 0.36% 0.09% 0 1240 124 10000 0.20% 0.15% 0.44% 0 530 53 10000 0.20% 0.12% 0.16% 0 420 42 10000 0.20% 0.10% 0.13% 0 410 41 10000 0.20% 0.05% 0.
PAGE 137
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 138
show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system. Syntax show processes memory {management-unit | stack unit {unit-id | all | summary}} Parameters management-unit Enter the keyword management-unit for CPU memory usage of the stack management unit. stack unit unit id Enter the keyword stack unit then a stack unit ID of the member unit for which to display memory usage on the forwarding processor.
PAGE 139
show processes memory output Field Description ResSize Actual resident size of the process in memory Size Process test, stack, and data size Allocs Total dynamic memory allocated Frees Total dynamic memory freed Max Maximum dynamic memory allocated Current Current dynamic memory in use The output for the show process memory command displays the memory usage statistics running on CP part (sysd) of the system. The sysd is an aggregate task that handles all the tasks running on S-Series’ CP.
PAGE 140
270 bcmDISC 117927936 0 0 269 bcmATP-RX 117927936 0 0 268 bcmATP-TX 117927936 0 0 267 bcmSTACK 117927936 0 0 266 bcmRX 117927936 0 0 265 bcmLINK.0 117927936 0 0 !----------- output truncated --------------! DellEMC# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 show reload-type Shows the reload type which occurs on the next reboot. Syntax show reload-type Parameters N/A Defaults normal-reload Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 141
Usage Information Example — Userinitiated reboot with the reload command Example — System reboot due to the upgrade command Example — System reboot for unknown reasons You can use the show reset-reason without the stack-unit option to view the reason for the last system reboot of the local system. DellEMC#show reset-reason Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 DellEMC# show reset-reason Cause: Reboot by Software upgrade Module. Reset Time: 8/9/2017 1:39 PM.
PAGE 142
show software ifm Display interface management (IFM) data. Syntax show software ifm {clients [summary] | ifagt number | ifcb interface | stack-unit unit-ID | trace-flags} Parameters clients Enter the keyword clients to display IFM client information. summary (OPTIONAL) Enter the keyword summary to display brief information about IFM clients. ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics.
PAGE 143
Example Version Description 7.6.1.0 Introduced for the C-Series and S-Series.
PAGE 144
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, us reload-type command. Modified the show system stack-unit command output to su Part ID (PPID). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot co "Present". 7.7.1.0 Added Master Priority field. 7.6.1.
PAGE 145
Reqd Mod Type : No Module - No Module -- Module 4 -Reqd Mod Type : No Module - No Module -- Module 4 -- -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed Power AvgPower AvgPowerStar ---------------------------------------------------------------------------------1 1 down UNKNOWN down 0 0 0 N/A 1 2 up AC up 26880 220 220 12/17/2017-08 -- Fan Status -Unit Bay TrayStatus Fan1 Speed ---------------------------------------------------------------------------------1 1 up up 13606 1 2 down 1 3 dow
PAGE 146
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced save to the file options. 7.6.1.0 Introduced on the S-Series. Without the page or stack-unit option, the command output is continuous. To interrupt the command output, use Ctrl-z. The save option works with other filtering commands.
PAGE 147
DellEMC# show tech-support stack-unit 1 | save flash://LauraSave Start saving show command report ....... DellEMC# DellEMC# dir Directory of flash: 1 drw- 16384 Jan 01 1980 00:00:00 +00:00 . 2 drwx 1536 Jul 13 1996 02:38:06 +00:00 ..
PAGE 148
Parameters Defaults -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 149
telnet Connect through Telnet to a server. The Telnet client and server in Dell EMC Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router. Syntax Parameters telnet {host | ip-address | ipv6-address prefix-length | vrf vrf instance name} [/source-interface] host Enter the name of a server. ip-address Enter the IPv4 address in dotted decimal format of the server.
PAGE 150
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Added support for source-interface for link-local IPv6 addressing. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series (IPv6). Increased the number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.
PAGE 151
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. terminal length Configure the number of lines displayed on the terminal screen. Syntax Parameters Defaults terminal length screen-length screen-length Enter a number of lines. Entering zero causes the terminal to display without pausing. The range is from 0 to 512. 24 lines Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 152
vrf instance (Optional) E-Series Only: Enter the keyword vrf then the VRF Instance name. ip-address Enter the IP address of the device in dotted decimal format. ipv6-address Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 153
Example (IPv4) DellEMC# traceroute www.Dell EMC Networking.com Translating "www.Dell EMC Networking.com"...domain server (10.11.0.1) [OK] Type Ctrl-C to abort. ----------------------------------------------Tracing the route to www.Dell EMC Networking.com (10.11.84.18), 30 hops max, 40 byte packets ----------------------------------------------TTL Hostname Probe1 Probe2 Probe3 1 10.11.199.190 001.000 ms 001.000 ms 002.000 ms 2 gwegress-sjc-02.Dell EMC Networking.com (10.11.30.126) 005.000 ms 001.000 ms 001.
PAGE 154
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 155
terminal Enter the keyword terminal to copy the current running configuration to the terminal. This command is similar to the show running-config command. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 156
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 157
• • • • • dot1x dot1x show show show supplicant-timeout tx-period dot1x cos-mapping interface dot1x interface dot1x profile debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x.
PAGE 158
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3.
PAGE 159
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 160
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: ● Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). ● Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command).
PAGE 161
Related Commands ● dot1x authentication (Interface) — enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific.
PAGE 162
Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9000 Series.
PAGE 163
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 164
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 165
Usage Information Version Description 9.10(0.0) Introduced on the S3100 series, S4048–ON, S4048–ON, S4810, S4820T, S5000, S6000, S6000–ON, S6100–ON, the Configuration Terminal Batch mode on C9010, Z9100–ON, and Z9500. 9.9(0.0) Introduced on the C9010. The mac command configures a list of supplicant MAC addresses for a dot1x profile represented with a profile-name. You can configure up to 6 MAC addresses in a single mac command.
PAGE 166
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-auth-bypass command. dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command.
PAGE 167
Parameters Defaults number Enter the number of supplicants that can be authenticated on a single port in Multi-auth mode. The range is from 1 to 128. The default is 128. 128 hosts can be authenticated on a single authenticator port. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 168
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.
PAGE 169
Related Commands ● dot1x static-mab ● mac dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command. Parameters Defaults seconds Enter the number of seconds. The range is from 1 to 65535. The default is 60. 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 170
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 171
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out.
PAGE 172
Ideally, the dot1x server-timeout value (in seconds) is based on the configured RADIUS-server timeout and retransmit values and calculated according to the following formula: dot1x servertimeout seconds > (radius-server retransmit seconds + 1) * radius-server timeout seconds. Where the default values are as follows: dot1x server-timeout (30 seconds), radius-server retransmit (3 seconds), and radius-server timeout (5 seconds). Example DellEMC(conf)# radius-server host 10.11.197.
PAGE 173
Critical VLAN: Critical VLAN id: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Static-MAB: Static-MAB Profile: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Enable 400 Disable Disable Enable Sample 30 seconds 60 seconds 2 30 seconds 30 seconds 60 seconds 2 SINGLE_HOST Authenticated Idle dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out.
PAGE 174
dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters Defaults seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535. The default is 30. 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 175
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. mac-address Defaults (Optional) MAC address of an 802.1X-authenticated supplicant. None Command Modes ● EXEC ● EXEC privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 176
802.1p CoS re-map table for Supplicant: 00:00:00:00:00:10 Dot1p 0 1 2 3 4 5 6 7 DellEMC# Remapped Dot1p 7 6 5 4 3 2 1 0 show dot1x interface Display the 802.1X configuration of an interface. Syntax show dot1x interface interface [mac-address mac-address] Parameters Defaults interface Enter one of the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 177
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added the mac-address option on the C-Series and S-Series. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. If you enable 802.1X multi-supplicant authentication on a port, additional 802.1X configuration details (Port Authentication status, Untagged VLAN ID, Authentication PAE state, and Backend state) display for each supplicant, as shown in the following example.
PAGE 178
Untagged VLAN id: Auth PAE State: Backend State: DellEMC# 400 Authenticated Idle DellEMC# show dot1x interface tengigabitethernet 1/1/1/1 mac-address 00:00:00:00:00:11 Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.
PAGE 179
----------------------------Dot1x Profile mySupplicants Profile MACs 00:50:56:aa:01:10 00:50:56:aa:01:11 802.
PAGE 180
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 181
• • • • • • • • • permit tcp (for IPv6 ACLs) permit udp (for IPv6 ACLs) seq (for IPv6 ACLs) permit (for IPv6 ACLs) deny arp (for Extended MAC ACLs) deny icmp (for Extended IPv6 ACLs) deny tcp (for IPv6 ACLs) deny udp (for Extended IP ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
PAGE 182
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode. You can configure up to 4294967291 remarks for a given IP ACL and 65536 remarks for a given MAC ACL.
PAGE 183
show config Display the current ACL configuration. Syntax show config Command Modes ● ● ● ● Command History Example CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 184
aclrange profile-name Create ACL range profiles for L4 ports. Syntax aclrange profile-name After entering the configuration mode of the ACL range, enter the following: type [inverse value] lower threshold upper-threshold Parameters Defaults profile-name Enter a valid name for the range profile. type Specify the type of the L4 port as source or destination. inverse Enter the keyword inverse followed by a value. This is used as a negative (not equal to) match.
PAGE 185
Command Modes LINE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 186
Parameters access-list-name (OPTIONAL) Enter the name of a configured access-list, up to 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 187
Example DellEMC(conf)#feature acloptimized Configuration change will be in effect after save and reload. ACL config containing TTL, layer3 and VRF conflicts with ACL Cam optimzation feature and these keywords would be discarded while applying the ACL. feature aclrange Enable the ACL range option. Syntax feature aclrange Use the no feature aclrange command to disable the option. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 188
layer3 Defaults (OPTIONAL) Enter the keyword layer3 to enable layer 3 mode. It ensures that all the ACL rules in the access-group are applied only for L3 router packets. Not enabled. Command Modes INTERFACE/VRF MODE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 189
ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 190
1 2 3 4 5 6 dport1 dport2 dportgt5000 ip-mtu-782 sport1 sportinv1 l4dstport l4dstport l4dstport mtu l4srcport l4srcport No No No No No Yes 80 3000 5001 782 1024 2500 89 3500 65535 782 65535 2500 To display the list of ACLs using the configured range profiles: DellEMC# show aclrange access-list Profile-name type Acl-name abc v4 abc V4 zyx V6 def bgp V6 ghi seqno 5 10 8 8 show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters.
PAGE 191
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for the 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.
PAGE 192
Parameters Defaults source Enter the IP address in dotted decimal format of the network from which the packet was sent. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host and then enter the IP address to specify a host IP address only. count (OPTIONAL) Enter the keyword count to count the packets. bytes (OPTIONAL) Enter the keyword bytes to count the bytes. log (OPTIONAL) Enter the keyword log to enter ACL matches in the log.
PAGE 193
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 194
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. Dell EMC Networking OS supports one ingress and one egress IP ACL per interface. Prior to Dell EMC Networking OS version 7.8.
PAGE 195
Defaults monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 196
resequence access-list Re-assign sequence numbers to entries of an existing access-list. Syntax resequence access-list {ipv4 | ipv6 | mac} {access-list-name StartingSeqNum Step-to-Increment} Parameters ipv4 | ipv6 | mac Enter the keyword ipv4or mac to identify the access list type to resequence. access-list-name Enter the name of a configured IP access list. Defaults StartingSeqNum Enter the starting sequence number to resequence. The range is from 0 to 4294967290.
PAGE 197
seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ipaddress}} [count [byte] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To delete a filter, use the no seq sequence-number command. Parameters Defaults sequencenumber Enter a number from 0 to 4294967290. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.
PAGE 198
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 199
deny Configure a filter that drops IP packets meeting the filter criteria. Syntax deny {ip | ip-protocol-number} {source mask | any | host ip-address} {destination mask | any | host ip-address} [ttl operator][count [byte] | log] [dscp value] [order] [monitor] [fragments] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 200
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 201
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [type] [ttl operator] [dscp] [count [byte] [order] [fragments] [monitor] [no-drop] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 202
● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults dscp Enter this keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter.
PAGE 203
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, see the Quality of Service section of the Dell EMC Networking OS Configuration Guide. The monitor option is relevant in the context of flow-based monitoring only.
PAGE 204
Use the established flag to match only ACK and RST flags of established TCP session. You cannot use established along with the other control flags While using the established flag in an ACL rule, all the other TCP control flags are masked, to avoid redundant TCP control flags configuration in a single rule. When you use any TCP control flag in an ACL rule, established is masked and other control flags are available.
PAGE 205
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 206
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands ● deny — assign a filter to deny IP traffic. ● deny udp — assign a filter to deny UDP traffic. deny udp To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 207
Defaults mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 208
Usage Information Version Description 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, see the Quality of Service section of the Dell EMC Networking OS Configuration Guide. The monitor option is relevant in the context of flow-based monitoring only. For more information, see the Port Monitoring section.
PAGE 209
Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 210
Defaults ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 211
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 212
parameter-problem count port-unreachable count source-quench count time-exceeded count For IPv6: echo count echo-reply count nd-ns count nd-na count packet-too-big count parameter-problem count time-exceeded count port-unreachable count The ICMP packets cannot be filtered using mirroring ACL. Defaults dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is 0 to 63.
PAGE 213
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Added support for noncontiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the Quality of Service chapter of the FTOS Configuration Guide. When you use the log option, the CP processor logs details about the packets that match.
PAGE 214
operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 215
Usage Information Version Description 9.11(2.0P0) Added the established parameter on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 216
5 6 7 8 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 7168 7680 7936 8000 7679 7935 7999 8000 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. DellEMC# Data Mask 1 0000000000000000 1111110000000000 0 From To #Covered 1023 1024 Total Ports: 1024 Related Commands ● ip access-list extended — create an extended ACL.
PAGE 217
● gt = greater than ● lt = less than ● range = inclusive range of ports (you must specify two ports for the port parameter) Defaults port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is 0 to 65535. destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter.
PAGE 218
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. . 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide.
PAGE 219
Step-toIncrement Defaults Enter the step to increment the sequence number. The range is from 1 to 4294967290. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 220
icmp Enter the keyword icmp to configure an ICMP access list filter. ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list permits all IP protocols. tcp Enter the keyword tcp to configure a TCP access list filter. udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received.
PAGE 221
talk telnet time uucp whois www Talk (517) Telnet (23) Time (37) Unix-to-Unix Copy Program (540) Nicname (43) World Wide Web (HTTP, 80) The following logical names are supported in UDP: biff Biff (mail notification, comsat, 512) bootpc Bootstrap Protocol (BOOTP) client (68) bootps Bootstrap Protocol (BOOTP) server (67) discard Discard (9) dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mo
PAGE 222
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). monitor (OPTIONAL) Enter the keyword monitor then the session–ID to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 223
Usage Information The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. The order option is relevant in the context of the Policy QoS feature only. The following applies: ● The seq sequence-number command is applicable only in an ACL group. ● The order option works across ACL groups that are applied on an interface via the QoS policy framework. ● The order option takes precedence over seq sequence-number.
PAGE 224
9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series TeraScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series TeraScale Added the monitor option. deny icmp Configure a filter to drop all or specific ICMP messages.
PAGE 225
deny tcp Configure a filter that drops TCP packets that match the filter criteria.
PAGE 226
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series TeraScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series TeraScale Added the monitor option. The C-Series cannot count both packets and bytes, so when you enter the count byte options, only bytes are incremented.
PAGE 227
Parameters Defaults source address Enter the IPv6 address of the network or host from which the packets were sent in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. The :: notation specifies successive hexadecimal fields of zero. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 228
7 8 0001111100000000 1111111111000000 7936 0001111101000000 1111111111111111 8000 7999 8000 64 1 Total Ports: 4001 Example An ACL rule with TCP port lt 1023 takes only one entry in the CAM: Rule# 1 Data Mask From 0000000000000000 1111110000000000 0 To 1023 #Covered 1024 Total Ports: 1024 Related Commands deny – assigns a filter to deny IP traffic. deny tcp – assigns a deny filter for TCP traffic. ipv6 access-list Configure an access list based on IPv6 addresses or protocols.
PAGE 229
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters. Prior to version 7.8.1.0, names are up to 16 characters long. 7.4.1.0 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent.
PAGE 230
Version Description 8.3.7.0 Introduced on the S4810. permit tcp Configure a filter to pass TCP packets that match the filter criteria. Syntax permit tcp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [bit] [operator port [port]] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 231
Defaults Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.
PAGE 232
● Use the no permit udp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} command. Parameters Defaults source address Enter the IPv6 address of the network or host from which the packets were sent in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. The :: notation specifies successive hexadecimal fields of zero. mask Enter a network mask in /prefix format (/x).
PAGE 233
7 0001111100000000 8 0001111101000000 1111111111000000 1111111111111111 7936 8000 7999 8000 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 takes only one entry in the CAM: Rule# 1 Data Mask From 0000000000000000 1111110000000000 0 To #Covered 1023 1024 Total Ports: 1024 Related Commands permit – assigns a permit filter for IP packets. permit tcp – assigns a permit filter for TCP packets.
PAGE 234
seq Assign a sequence number to a deny or permit the filter in an IPv6 access list while creating the filter. Syntax seq sequence-number {deny | permit} {ipv6-protocol-number | icmp | ip | tcp | udp} {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [operator port [port]] [count [byte]] | [log] [monitor] To delete a filter, use the no seq sequence-number command. Parameters sequencenumber Enter a number from 0 to 4294967290.
PAGE 235
Defaults message-type (OPTIONAL) Enter an ICMP message type, either with the type (and code, if necessary) numbers or with the name of the message type . The range is 0 to 255 for ICMP type and 0 to 255 for ICMP code. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. Not configured. Command Modes ACCESS-LIST Command History Related Commands This guide is platform-specific.
PAGE 236
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 237
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 238
● For a port-channel interface, enter the keywords port-channel then the port-channel ID. in | out Identify whether ACL is applied on ingress or egress side. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 239
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 240
deny To drop packets with a the MAC address specified, configure a filter. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {any | mac-source-address mac-source-address-mask} command. Parameters Defaults any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 241
Usage Information When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands ● permit — configures a MAC address filter to pass packets.
PAGE 242
NOTE: Ingress ACLs are supported on C-Series and S-Series platforms only. Example DellEMC(conf)# mac-access-list access-list standard TestMAC DellEMC(config-std-macl)# permit 00:00:00:00:00:00 00:00:00:00:ff:ff count DellEMC(config-std-macl)# deny any count DellEMC(config-std-macl)# permit To forward packets from a specific source MAC address, configure a filter.
PAGE 243
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 244
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see “Flow-based Monitoring” in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. Not configured Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History Usage Information This guide is platform-specific.
PAGE 245
deny To drop packets that match the filter criteria, configure a filter. Syntax deny {any | host mac-address | mac-source-address mac-source-addressmask} {any | host mac-address | mac-destination-address mac-destinationaddress-mask} [ethertype-operator] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 246
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 247
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 248
permit To pass packets matching the criteria specified, configure a filter. Syntax permit {any | host mac-address | mac-source-address mac-source-addressmask} {any | host mac-address | mac-destination-address mac-destinationaddress-mask} [ethertype operator] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 249
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 250
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 251
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 252
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information Prefix lists redistribute OSPF and RIP routes meeting specific criteria.
PAGE 253
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 254
Example Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf-nprefixl)# show config ! ip prefix-list snickers DellEMC(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. Syntax show ip prefix-list detail [prefix-name] Parameters prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters.
PAGE 255
seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) DellEMC# show ip prefix-list summary Display a summary of the configured prefix lists. Syntax Parameters show ip prefix-list summary [prefix-name] prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 256
continue To a route-map entry with a higher sequence number, configure a route-map. Syntax continue [sequence-number] Parameters Defaults sequencenumber (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Not configured. Command Modes ROUTE-MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 257
● If a set action occurs in the first route map entry and then the same set action occurs with a different value in a subsequent route map entry, the last set of actions overrides the previous set of actions with the same set command. ● If set community additive and set as-path prepend are configure, the communities and AS numbers are prepended. Related Commands ● set community — specify a COMMUNITY attribute. ● set as-path — configure a filter to modify the AS path.
PAGE 258
Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 259
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 260
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 261
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 262
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 263
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 264
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address.
PAGE 265
Version Description 8.1.1.0 Introduced on the E-Series. pre-6.1.1.0 Introduced on the E-Series. match route-type To match routes based on the how the route is defined, configure a filter. Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command.
PAGE 266
Related Commands ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address. ip route-source — redistribute routes that match routes advertised by other routers. metric — redistribute routes that match a specific metric. tag — redistribute routes that match a specific tag.
PAGE 267
route-map Enable a route map statement and configure its action and sequence number. This command also places you in ROUTE-MAP mode. Syntax route-map map-name [permit | deny] [sequence-number] To delete a route map, use the no route-map map-name [permit | deny] [sequencenumber] command. Parameters Defaults map-name Enter a text string of up to 140 characters to name the route map for easy identification. permit (OPTIONAL) Enter the keyword permit to set the route map default as permit.
PAGE 268
Example Related Commands DellEMC(conf)# route-map dempsey DellEMC(config-route-map)# ● show config — display the current configuration. set as-path To modify the AS path for border gateway protocol (BGP) routes, configure a filter. Syntax set as-path prepend as-number [... as-number] To remove an AS-Path setting, use the no set as-path {prepend as-number | tag} command.
PAGE 269
set automatic-tag To automatically compute the tag value of the route, configure a filter. Syntax set automatic-tag To return to the default, enter no set automatic-tag. Defaults Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 270
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 271
no-advertise Enter the keywords no-advertise to drop all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to drop all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary.
PAGE 272
Parameters Defaults backbone Enter the keyword backbone to redistribute matched routes to the OSPF backbone area (area 0.0.0.0). level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Not configured.
PAGE 273
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 274
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 275
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 276
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you configure the set next-hop command, its configuration takes precedence over the neighbor next-hop-self command in the ROUTER BGP mode.
PAGE 277
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command. Parameters Defaults tag-value Enter a number as the tag. The range is from zero (0) to 4294967295.
PAGE 278
set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Syntax set weight weight To delete a weight specification, use the no set weight weight command. Parameters weight Enter a number as the weight used by the route meeting the route map specification. The range is from 0 to 65535. The default is router-originated = 32768 and all other routes = 0.
PAGE 279
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 280
Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 281
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 282
Parameters Defaults ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 283
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 284
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 285
Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 286
Related Commands ● deny — assign a filter to deny IP traffic. ● deny udp — assign a filter to deny UDP traffic. deny ether-type (for Extended MAC ACLs) Configure an egress filter that drops specified types of Ethernet packets on egress ACL supported line cards. (For more information, refer to your line card documentation).
PAGE 287
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 288
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 289
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 290
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 291
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the {destination-mac-address mac-address-mask | any} vlan vlan-id {ipaddress | any | opcode code-number} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 292
permit ether-type (for Extended MAC ACLs) Configure a filter that allows traffic with specified types of Ethernet packets. This command is supported only on 12-port GE line cards with SFP optics. For specifications, refer to your line card documentation.
PAGE 293
monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG).
PAGE 294
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 295
● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 296
packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands ● ip access-list extended — create an extended ACL. ● permit — assign a permit filter for IP packets. ● permit tcp — assign a permit filter for TCP packets. permit (for Extended IP ACLs) To pass IP packets meeting the filter criteria, configure a filter.
PAGE 297
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 298
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
PAGE 299
seq (for Standard MAC ACLs) To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax seq sequence-number {deny | permit} {any | mac-source-address [mac-sourceaddress-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 300
be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 301
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 302
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. You can enter a threshold in the range of 1-100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. You can enter an interval in the range of 1-10 minutes.
PAGE 303
Syntax seq sequence-number {deny | permit} ether-type protocol-type-number {destination-mac-address mac-address-mask | any} vlan vlan-id {source-macaddress mac-address-mask | any} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 304
seq (for IP ACLs) Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 305
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 306
packet-too-big count parameter-problem count port-unreachable count source-quench count time-exceeded count For IPv6: echo count echo-reply count nd-ns count nd-na count packet-too-big count parameter-problem count time-exceeded count port-unreachable count The ICMP packets cannot be filtered using mirroring ACL. Defaults ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255.
PAGE 307
Usage Information Version Description 9.11(2.0P1) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.
PAGE 308
host ipv6- address Enter the keyword host then the IP address to specify a host IP address. destination address Enter the IPv6 address of the network or host to which the packets are sent.
PAGE 309
which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 310
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [operator port [port]] [ttl operator] [count [byte]] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 311
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 312
source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) . any Enter the keyword any to specify that all routes are subject to the filter. host ipv6- Enter the keyword host and then enter the IPv6 address to specify a host IP address or hostname.
PAGE 313
The following logical names are supported in UDP: biff Biff (mail notification, comsat, 512) bootpc Bootstrap Protocol (BOOTP) client (68) bootps Bootstrap Protocol (BOOTP) server (67) discard Discard (9) dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mobile-ip Mobile IP registration (434) nameserver IEN116 name service (obsolete, 42) netbios-dgm NetBios datagram service (138) netbios-ns N
PAGE 314
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 315
no-drop Defaults Enter the keywords no-drop to match only the forwarded packets. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 316
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny arp {destination-mac-address mac-address-mask | any} vlan vlan-id {ip-address | any | opcode code-number} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 317
deny icmp (for Extended IPv6 ACLs) Configure a filter to drop all or specific ICMP messages. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here. For a complete description on all of the keywords and variables that are available with this command, refer the topic of this command discussed earlier in this guide.
PAGE 318
● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values.
PAGE 319
MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 320
● range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: ● 23 = Telnet ● 20 and 21 = FTP ● 25 = SMTP ● 169 = SNMP Defaults ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255.
PAGE 321
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 322
● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 323
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. no-drop Enter the keywords no-drop to match only the forwarded packets.
PAGE 324
7 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 325
ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
PAGE 326
You can only enable BFD for VRRP in INTERFACE command mode (vrrp bfd all-neighbors). You can enable BFD on both default and nondefault VRFs for OSPF and BGP protocols for both IPv4 and IPv6 neighbors. NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd disable Disable BFD on an interface. Syntax bfd disable Re-enable BFD using the no bfd disable command. Defaults BFD is disabled by default. Command Modes VRRP Command History This guide is platform-specific.
PAGE 327
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd enable (Interface) Enable BFD on an interface.
PAGE 328
Parameters interval milliseconds min_rx milliseconds Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200. Dell EMC recommends using more than 100 milliseconds. Enter the keywords min_rx to specify the minimum rate at which the local system would like to receive control packets from the remote system. The range is from 50 to 1000. The default is 200.
PAGE 329
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 330
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced the vrf keyword on S3100 series, S3048–ON, S4048–ON, S4048TON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.5) Introduced the vrf keyword on the Z9100–ON. 9.11(0.0) Introduced the prefix-list keyword. 9.10(0.
PAGE 331
● Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is Active. Defaults See Parameters. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.2) Introduced support for enabling BFD on non-default VRFs for OSPFv2. 9.10(0.
PAGE 332
Defaults See Parameters. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.
PAGE 333
Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6100–ON, C9010, and the Z9500. 9.12(1.0) Introduced on the S5048F–ON. 9.11(2.5) Introduced the ipv6 route bfd command on the Z9100–ON.
PAGE 334
Usage Information When you enable a BFD session with a specified BGP neighbor or peer group using the bfd neighbor command, the default BFD session parameters are used (interval: 200 milliseconds, min_rx: 200 milliseconds, multiplier: 3 packets, and role: active) if you have not specified parameters with the bfd neighbor command.
PAGE 335
Usage Information When you explicitly disable a BGP neighbor for a BFD session with the neighbor bfd disable command: ● The neighbor does not inherit the global BFD disable values configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs. ● The neighbor only inherits the global timer values configured with the bfd neighbor command: interval, min_rx, and multiplier.
PAGE 336
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Added support for BFD for BGP on the S4810. 8.4.1.3 Added support for BFD for BGP on the E-Series. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for BFD for VLAN and port-channel interfaces on the E-Series. 7.4.1.0 Introduced BFD on physical ports on the E-Series.
PAGE 337
Example (Detail) The following example shows the show bfd vrf neighbors detail command output showing the nondefault VRF called “VRF_blue”. show bfd vrf VRF_blue neighbors detail Session Discriminator: 5 Neighbor Discriminator: 3 Local Addr: 5.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 5.1.1.
PAGE 338
Role: Active Delete session on Down: True VRF: VRF_blue Client Registered: OSPF Uptime: 00:00:14 Statistics: Number of packets received from neighbor: 73 Number of packets sent to neighbor: 73 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Related Commands ● bfd all-neighbors — establish BFD sessions with all neighbors discovered by the IS-IS protocol or OSPF protocol out of all interfaces.
PAGE 339
Version Description 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 340
8 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 341
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.5.1.
PAGE 342
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 343
Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 344
Usage Information Version Description 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
PAGE 345
DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process.
PAGE 346
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipathrelax command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 347
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The software compares the MEDs only if the path contains no external autonomous system numbers.
PAGE 348
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 349
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 350
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster.
PAGE 351
The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation. Dell EMC Networking OS accepts confederation EBGP peers without a LOCAL_PREF attribute. The software sends AS_CONFED_SET and accepts AS_CONFED_SET and AS_CONF_SEQ.
PAGE 352
Usage Information All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. After specifying autonomous systems numbers for the BGP confederation, recycle the peers to update their configuration. Related Commands ● bgp confederation identifier — configure a confederation ID.
PAGE 353
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enter the bgp dampening command, the default values for half-life, reuse, suppress, and max-suppress-time are applied.
PAGE 354
Usage Information All routers apply the bgp default local-preference command setting within the AS. To set the local preference for a specific route, use the set local-preference command in ROUTE-MAP mode. Related Commands ● set local-preference — assign a local preference value for a specific route. bgp dmzlink-bw Enables BGP Link Bandwidth. Syntax bgp dmzlink-bw To disable BGP Link Bandwidth, enter the no bgp dmzlink-bw command.
PAGE 355
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 356
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The bgp fast-external-fallover command appears in the show config command output.
PAGE 357
Where the 2-byte format is from 1 to 65535, the 4-byte format is from 1 to 4294967295. Both formats are accepted and the advertisements reflect the entered format. For more information about using the 2 byte or 4-byte format, refer to the Dell EMC Networking OS Configuration Guide. This command automatically restarts the BGP instance for the configuration to take effect.
PAGE 358
This command automatically restarts the BGP instance for the configuration to take effect. bgp non-deterministic-med Compare MEDs of paths from different autonomous systems. Syntax bgp non-deterministic-med To return to the default, use the no bgp non-deterministic-med command. Defaults Disabled (that is, paths/routes for the same destination but from different ASs do not have their MEDs compared). Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 359
Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Version Description 9.4.(0.0) Introduced on the S4810. 9.2(1.0) Introduced on the Z9500.
PAGE 360
Usage Information This command is a knob to disable BGP next-hop resolution using BGP learned routes. During the nexthop resolution, only the first route that the next-hop resolves through is verified for the route’s protocol source and is checked if the route is learned from BGP or not. The clear ip bgp command is required for this command to take effect and to keep the BGP database consistent. Execute the clear ip bgp command right after executing this command.
PAGE 361
Examples DellEMC(conf-router_bgp)# no bgp regex-eval-optz-disable DellEMC(conf-router_bgp)# do show ip protocols Routing Protocol is "ospf 22222" Router ID is 2.2.2.2 Area Routing for Networks 51 10.10.10.0/00 Routing Protocol is "bgp 1" Cluster Id is set to 10.10.10.0 Router Id is set to 10.10.10.
PAGE 362
Usage Information Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection. Syntax clear ip bgp [vrf vrf-name] [* | <1–4294967295> | <0.1–65535.65535> | A.B.C.
PAGE 363
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 6.5.1.0 Expanded to include the as-number option.
PAGE 364
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. After you enter this command, the software deletes the history routes and returns the suppressed routes to the Active state. The clear ip bgp dampening command does not clear the history paths. clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap.
PAGE 365
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 366
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 367
updates Enter the keyword updates to view BGP updates. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.
PAGE 368
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view dampened-route information related only to ipv6 unicast routes.
PAGE 369
out (OPTIONAL) Enter the keyword out to view only events on outbound BGP messages. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 370
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.
PAGE 371
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added ipv6 support. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command.
PAGE 372
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors. debug ip bgp updates Allows you to view information about BGP updates. Syntax debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 373
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command.
PAGE 374
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The default-metric command in BGP sets the value of the BGP MULTI_EXIT_DISC (MED) attribute for redistributed routes only. Related Commands ● bgp always-compare-med — enable comparison of all BGP MED attributes. ● redistribute — redistribute routes from other routing protocols into BGP.
PAGE 375
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 376
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Support from 2 to 64 paths on the S4810. Command syntax changed to maxpath (was maximum-paths). 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 377
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. By default, when you create a neighbor/peer group configuration in the Router BGP context, this enables IPv4/Unicast AFI/SAFI.
PAGE 378
Defaults receive Enter the keyword receive to indicate that the system accepts multiple paths from peers. both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported. The range is from 2 to 64. none Command Modes CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY Command History Related Commands This guide is platform-specific.
PAGE 379
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 380
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peer-group-name} allowas-in command.
PAGE 381
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ip-address | peer-group-name} default-originate [route-map mapname] To remove a default route, use the no neighbor {ip-address | peer-group-name} default-originate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the default route of all routers in that peer group.
PAGE 382
You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. In order that settings corresponding to the neighbor default-originate command take effect, you must execute the clear ip bgp command immediately after you execute the neighbor default-originate command. neighbor description Assign a character string describing the neighbor or group of neighbors (peer group).
PAGE 383
To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to apply the distribute list filter to all routers in the peer group. prefix-list-name Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes).
PAGE 384
ttl Defaults (OPTIONAL) Enter the number of hops as the Time to Live (ttl) value. The range is from 1 to 255. The default is 255. Disabled. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 385
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.
PAGE 386
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation.
PAGE 387
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 388
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 389
dmzlink-bw Defaults Enter the keyword dmzlink-bw to attach a link bandwidth to received routes. NOTE: If dmzlink-bw is configured for a peer, in order for the BGP peer to advertise the prefixes with dmzlink-bw attached to it, you must reset the the peer or peer-group using the clear ip bgp session command. Not configured. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 390
neighbor peer-group (creating group) Allows you to create a peer group and assign it a name. Syntax neighbor peer-group-name peer-group To delete a peer group, use the no neighbor peer-group-name peer-group command. Parameters Defaults peer-group-name Enter a text string up to 16 characters long as the name of the peer group. Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 391
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 392
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 393
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Applies to EBGP neighbors only.
PAGE 394
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 395
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed.
PAGE 396
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 397
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group.
PAGE 398
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group.
PAGE 399
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Timer values configured with the neighbor timers command override the timer values configured with any other command.
PAGE 400
neighbor update-source Enable the E-Series software to use Loopback interfaces for TCP connections for BGP sessions. Syntax neighbor {ip-address | peer-group-name} update-source interface To use the closest interface, use the no neighbor {ip-address | peer-group-name} update-source interface command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group.
PAGE 401
Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group. weight Defaults Enter a number as the weight. The range is from 0 to 65535. The default is 0. 0 Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 402
mask Enter the mask of the IP address in the slash prefix length format (for example, / 24). The mask appears in command outputs in dotted decimal format (A.B.C.D). route-map mapname (OPTIONAL) Enter the keyword route-map then the name of an established route map.
PAGE 403
In BGP, the next-hop for the route is calculated from the information that is acquired through IGP or static routes. Related Commands ● redistribute — redistribute routes into BGP. network backdoor Specify this IGP route as the preferred route. Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network.
PAGE 404
To disable this setting, enter the no permit bandwidth command. Parameters Defaults bandwidth Enter the keyword bandwidth to specify extended-community attribute as the matching criteria for permitting traffic. The range is from 0 to 102400. N/A Command Modes EXTENDED COMMUNITY LIST Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 405
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 406
Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 (OPTIONAL) Enter the keywords match external to redistribute OSPF external | 2} routes. You can specify 1 or 2 to redistribute those routes only. match internal (OPTIONAL) Enter the keywords match internal to redistribute OSPF internal routes only. route-map map- (OPTIONAL) Enter the keywords route-map then the name of a configured route map. name Defaults Not configured.
PAGE 407
Defaults Not enabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 408
shutdown address-family-ipv4–multicast Disables all the BGP neighbors corresponding to the multicast IPv4 address families. Syntax shutdown address-family-ipv4–unicast Use the no shutdown address-family-ipv4–unicast command to enable all the configured BGP neighbors corresponding to the multicast IPv4 address families. Command Modes ROUTER BGP CONFIGURATION Command History Usage Information Version Description 9.11.0.0 Introduced on the S-Series, Z-Series, MXL, and IOM.
PAGE 409
This command is global for all VRFs. set extcommunity bandwidth Enables you to set extended community bandwidth. Syntax set extcommunity bandwidth To disable extended community bandwidth, enter the no set extcommunity bandwidth command. Parameters Defaults bandwidth Enter the keyword bandwidth to enable extended community bandwidth. The range is from 0 to 102400. N/A Command Modes ROUTER MAP Command History Usage Information This guide is platform-specific.
PAGE 410
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 411
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 412
longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. cluster-list (OPTIONAL) Enter the keyword cluster-list then the cluster-ID to display the routes matching the cluster. cluster-id community communitynumber community-list community-listname (OPTIONAL) Enter the keyword community then the community–number to display the routes matching the communities.
PAGE 413
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 414
Received from : 1.1.1.2 (3.3.3.1) Best AS_PATH : Next-Hop : 1.1.1.2, Cost : 0 Origin IGP, Metric 0, LocalPref Extended Communities : DMZ-Link Bw: 2000 kbytes* 100, Weight 0, internal Following is the example for displaying all the received routes from all IPv4 neighbors: DellEMC# show ip bgp vrf test ipv4 unicast neighbors all received-routes BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 1.1.1.
PAGE 415
● show ip bgp community — view information on all routes with Community attributes or view specific BGP community groups. ● show ip bgp community-list — view routes that a specific community list affects. ● show ip bgp dampened-paths — view BGP routes that are dampened (non-active). ● show ip bgp extcommunity-list — view information on all routes with Extended Community attributes. ● show ip bgp filter-list — view the routes that match the filter lists.
PAGE 416
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router.
PAGE 417
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. communitynumber Enter the community number in AA:NN format where AA is the AS number (2 bytes) and NN is a value specific to that autonomous system.
PAGE 418
The show ip bgp community command without any parameters lists BGP routes with at least one BGP community attribute and the output is the same as for the show ip bgp command output. The following describes the show ip bgp community command shown in the following example. Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table.
PAGE 419
exact-match Enter the keyword for an exact match of the communities. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 420
DellEMC# show ip bgp 55.0.0.0/24 BGP routing table entry for 55.0.0.0/24 Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 172.16.0.2 (172.16.0.2) AS_PATH : 200 Best Next-Hop : 172.16.0.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref Communities : 200:1 1000:1 DellEMC# 100, Weight 0, external 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active).
PAGE 421
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized.
PAGE 422
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 423
AfNwCtxAddr 1101112443 : AfNwCtxAddrlen 255 : AfNetBKDrRttP 0x41a0d500 : AfNetBKDRCnt 0 : AfDampHLife 0 AfDampReuse 0 : AfDampSupp 0 : AfDampMaxHld 0 : AfDampCeiling 0 : AfDampRmapP DellEMC# show ip bgp extcommunity-list View information on all routes with Extended Community attributes.
PAGE 424
Usage Information To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found. The show ip bgp community command without any parameters lists BGP routes with at least one BGP community attribute and the output is the same as for the show ip bgp command output.
PAGE 425
Usage Information Example Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp filter-list hello command shown in the following example.
PAGE 426
Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view flap statistics on BGP routes corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 427
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp flap command shown in the following example. Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route. Flaps Displays the number of times the route flapped.
PAGE 428
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 429
*>n 11.11.11.11/32 0.0.0.0 *>n 22.22.22.22/32 0.0.0.0 I 32.32.32.32/32 60.0.0.2 I 32.32.33.33/32 60.0.0.2 *>n 33.33.33.33/32 0.0.0.0 *>n 33.33.44.55/32 0.0.0.0 *>n 44.44.44.44/32 0.0.0.0 *>I 55.55.0.0/16 72.1.1.2 *>I 55.55.55.55/32 72.1.1.2 *>I 55.55.66.66/32 72.1.1.2 *>a 66.66.0.0/16 0.0.0.0 *>n 66.66.66.77/32 0.0.0.0 *>n 66.66.77.77/32 0.0.0.
PAGE 430
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced the [all] option for IPv4 and IPv6 neighbors. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 431
The Lines Beginning with: Description ● last read is the time (hours:minutes:seconds) the router read a message from its neighbor ● hold time is the number of seconds configured between messages from its neighbor ● keepalive interval is the number of seconds between keepalive messages to help ensure that the TCP session is still alive.
PAGE 432
Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes
PAGE 433
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop.
PAGE 434
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF for the S4810, S4820T, and S6000. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 435
show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Syntax show ip bgp [vrf vrf-name] paths community Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 436
show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]] Parameters ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 437
Line beginning Description with: Example Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported. Minimum time Displays the time interval between BGP advertisements. For address family Displays IPv4 Unicast as the address family. BGP neighbor Displays the name of the BGP neighbor.
PAGE 438
● ● ● ● [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element. { } = (braces) minimum and the maximum match count. ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. ● $ = (dollar sign) the end of the output string.
PAGE 439
*> 55.0.0.0/24 *> 66.0.0.0/24 DellEMC# 172.16.0.2 172.16.0.2 0 200 i 0 200 i show ip bgp summary Allows you to view the status of all BGP connections. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view the status of all BGP connections corresponding to that VRF.
PAGE 440
same cluster_id, then the cluster_id count is 1000, since the same value is stored for thousand different attribute records. The attribute next-hop is a part of the BGP attribute data structure. If two peers send the same route that contains similar path attributes, then two entries are maintained in the back-end, as both these entries have different next-hops. If this same route is sent to a different peer, an entry for each peer is created, as the next-hop is different.
PAGE 441
Field Description If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm). When the peer is transitioning between states and clearing the routes received, the phrase (Purging) may appear in this column. If the neighbor is disabled, the phrase (Admin shut) appears in this column. Example DellEMC# show ip bgp summary BGP router identifier 192.168.11.
PAGE 442
Example DellEMC# show running-config bgp ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC# timers bgp Adjust the BGP Keep Alive and Hold Time timers. Syntax timers bgp keepalive holdtime To return to the default, use the no timers bgp command. Parameters Defaults keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers.
PAGE 443
timers bgp extended Adjust the BGP idle holdtime for all the BGP neighbors. Syntax timers bgp extended idle-holdtime To return to the default, use the no timers bgp extended command. Parameters extended idle- holdtime Defaults Enter a number for the time interval, in seconds, for the peer to be idle state. The range is from 1 to 32767. The default is 15 seconds. The default idle-holdtime is 15 seconds. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 444
Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 unicast routes.
PAGE 445
Command Modes ROUTER BGP (conf-router_bgp_af) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 9.7(0.
PAGE 446
show ip bgp dampened-paths View BGP routes that are dampened (non-active). Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
PAGE 447
Example Field Description Network Displays the network ID to which the route is dampened. From Displays the IP address of the neighbor advertising the dampened route. Reuse Displays the hour:minutes:seconds until the dampened route is available. Path Lists all the ASs the dampened route passed through to reach the destination network. DellEMC# show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 448
9 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 449
● ipv4udfmirracl: 0 ● ipv4mirracl: 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 0 to 8 in multiples of 2. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 9 in multiples of 3, when ipv4udfenable is selected. If not enabled, it is in multiples of 2. If the feature acloptimized command is enabled, the allocation is in multiples of 1.
PAGE 450
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.5) Added the keyword radius-v4acl on the S3048–ON. 9.14(1.3P2) Added the keyword radius-v4acl on the S3100 series. 9.14(0.0) Added the keyword ipv6mirracl on the S6000 and S6000–ON.
PAGE 451
Parameters default Reset the egress CAM ACL entries to default settings. l2acl number Set the number of blocks for L2 egress ACL entries. ipv4acl number Set the number of blocks for IPv4 egress ACL entries. ipv6acl number Set the number of blocks for IPv6 egress ACL entries. It must be a multiple of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 452
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 453
Example The following example shows that IPv4 QoS is disabled and IPv6 ACL is set to 4. With this configuration, you can share a total of 480 entries between the IPv4 QoS and IPv6 ACL regions after allocating 32 entries for IPv4 QoS. DellEMC(conf)# cam-sharing ipv4qos 50 ipv6acl 50 DellEMC(conf)#cam-acl l2acl 0 ipv4acl 0 ipv6acl 4 ipv4qos 0 l2qos 0 l2pt 0 ipmacacl 1 vman-qos 0 cam-threshold Configure CAM threshold value for sending the syslog message on CAM usage.
PAGE 454
To disable this feature, use the no feature ipv6acloptimized command. Command Modes CONFIGURATION Defaults Not configured Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Usage Information Example Version Description 9.14(0.0) Introduced on the S5048F–ON, S6100–ON, and Z9100–ON..
PAGE 455
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. The display reflects the settings implemented with the cam-acl command.
PAGE 456
show cam-sharing Display the configured CAM space sharing information between IPv6 ACL and IPv6 QoS in percentage. Syntax show cam-sharing Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S6100–ON, and Z9100–ON.
PAGE 457
Table 3.
PAGE 458
test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax test cam-usage service-policy input input policy name stack-unit {number | all} Parameters Defaults policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters. number Enter all to get information for all the stack-units or enter the stack-unit number to get information for a specific stack-unit.
PAGE 459
Example Example Term Explanation Estimated CAM per Port Estimates the amount of CAM space the listed policy will require. Status Indicates whether or not the policy will be allowed in the CAM.
PAGE 460
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.. Usage Information This command takes effect only after reboot. Related Commands show hardware forwarding-table mode — displays the hardware forwarding table mode in the current boot and in the next boot. show hardware forwarding-table mode Display the hardware forwarding table mode in the current boot and in the next boot.
PAGE 461
10 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 462
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. cpu-protocol-group Creates or removes a protocol group. Syntax cpu-protocol-group group-name Use the no cpu-protocol-group group-name command to remove the protocol-group. Command Modes CONFIGURATION Parameters Command History Example group-name Enter the unique protocol-group name that you want to create. NOTE: The length of the group-name that you specify cannot exceed 32 characters.
PAGE 463
cpu-queue Configures queue parameters. Syntax cpu-queue queue-number {protocol-group group-name [qos-policy policy-name] | qos-policy policy-name} Use the no cpu-queue queue-number command to remove the queue parameter configuration. Command Modes COPP-PROFILE Parameters queue-number Enter the queue number that you want to configure. The range is from 0 to 11. A queue can be mapped to a protocol-group or a qos-policy or both. Protocol groups cannot be configured for queue numbers 0 and 4.
PAGE 464
● Ensure that the service-class cpu-queue-buffer command is not configured. The copppolicy command will not be available if the service-class cpu-queue-buffer command is configured. ● Ensure that the service-policy rate-limit-cpu-queues command is not configured, The copp-policy command will not be available if the service-policy rate-limit-cpuqueues is configured. ● You cannot associate a protocol group with more than one queue. ● Ensure that each queue contains a unique protocol list.
PAGE 465
Command Modes QOS-POLICY-INPUT Parameters Default Command History Usage Information Example queue-lengthvalue Enter the queue length value you want to configure. The range is from 0 to 235. The default value is 235. Version Description 9.11.0.0 Introduced on the S6000, S6000–ON, Z9100–ON, and S6100–ON. The queue-length takes effect only if the qos-policy is associated with a copp-policy.
PAGE 466
Usage Information Create a policy-map by associating a queue number with the qos-policy. Create QoS policies prior to enabling this command. For CoPP, use the keyword cpu-qos when creating qos-policy-input. Related Commands ● qos-policy-input — create a QoS input policy map. ● policy-map-input — create an input policy map. service-policy rate-limit-protocols Apply a policy for the system to rate limit control protocols on a per-protocol basis.
PAGE 467
show cpu-queue rate cp Display the rates for each CPU queue. Syntax show cpu-queue rate cp Defaults Not configured. Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 468
Defaults Not configured. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Modified the output to display MCAST data packet information. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 469
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 470
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 471
Example DellEMC#show running-config cpu-protocol-group ! cpu-protocol-group PG0 protocol-list 802dot1x , arp-req , arp-rsp ! cpu-protocol-group PG1 protocol-list arp-req , arp-rsp , ip-local-term ! cpu-protocol-group PG3 protocol-list ttl0 , ttl1 DellEMC# Control Plane Policing (CoPP) 471
PAGE 472
11 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 473
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 474
show hardware pfc-nodrop-priority — displays the packets drop count corresponding to the priority. clear pfc counters Clear the PFC TLV counters and PFC statistics on an interface or stack unit. Syntax clear pfc counters [interface-type | stack-unit {unit number | all } all stack-ports all}] Parameters interface interface-type Enter the keywords port-type then the interface information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 475
Usage Information Used to enable honoring of PFC frames on all queues (lossy and lossless) and to initiate PFC storm control on all queues, when PFC storm control is configured with PFC asymmetric on an interface. 1. Enable pfc asymmetric on interface. 2. Configure pfc storm control to disable the queue if the pfc storm is detected. 3. Clear the queue disable state when the queue is disabled during the pfc storm detection.
PAGE 476
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. ● When you configure lossless queues on an interface, PFC priority configuration is not allowed on the dcb-map profile applied on the interface. ● The maximum number of lossless queues globally supported on the switch is two. The following lists the dot1p priority-queue assignments.
PAGE 477
Usage Information Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. The default number of 802.1p priorities that you can enable for PFC is 2. The maximum number of 802.1p priorities that you can enable for PFC is –4. Queues to which PFC priority traffic is mapped are lossless by default. Traffic may be interrupted due to an interface flap (going down and coming up) when you reconfigure the lossless queues for no-drop priorities.
PAGE 478
show hardware pfc-nodrop-priority View the packets drop count corresponding to the priority. Syntax show hardware pfc-nodrop-priority l2-dlf drops stack-unit stack-unit-number port-set port-pipe Parameters stack-unit stack- Enter the keywords stack-unit and the stack unit number. unit-number port-set port- pipe Enter the keywords port-set and port-pipe number. The port-pipe number is 0. Command Modes EXEC EXEC Privilege Command History Example Related Commands Version Description 9.10(0.
PAGE 479
Command Modes EXEC Privilege CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 480
Example (Summary) Field Description Application Priority TLV: FCOE TLV Tx Status Status of FCoE advertisements in application priority TLVs from the local DCBX port: enabled or disabled. Application Priority TLV: SCSI TLV Tx Status Status of ISCSI advertisements in application priority TLVs from the local DCBX port: enabled or disabled. Application Priority TLV: Local FCOE Priority Map Priority bitmap the local DCBX port uses in FCoE advertisements in application priority TLVs.
PAGE 481
Admin mode is on Admin is enabled Remote is disabled Local is enabled Pfc Type is Asymmetric Oper status is init PFC DCBX Oper status is Down Reason: Port Shutdown State Machine Type is Symmetric TLV Tx Status is enabled PFC Link Delay 65535 pause quntams Application Priority TLV Parameters : -------------------------------------FCOE TLV Tx Status is disabled ISCSI TLV Tx Status is disabled Local FCOE PriorityMap is 0x0 Local ISCSI PriorityMap is 0x0 1 Input TLV pkts, 4 Output TLV pkts, 0 Error pkts, 0 Paus
PAGE 482
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Example (Summary) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Enabled to display the command output even without enabling DCB. Introduced on the S6100–ON. 9.9(0.
PAGE 483
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 484
Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. show interface ets Displays the ETS configuration applied to egress traffic on an interface, including priority groups with priorities and bandwidth allocation. Syntax show interface port-type slot/port[/subport] ets {summary | detail} Parameters port-type slot/ port[/subport] ets Enter the port-type slot and port ETS information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 485
-----------------Admin is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rate(Mbps) Burst(KB) ---------------------------------------------------------------------------------0 0,1,2,3,4,5,6,7 100 ETS 1 2 3 4 5 6 7 15 Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rate(Mbps) Burst(KB) ----------------------------------------------------------
PAGE 486
Oper status is init ETS DCBX Oper status is Down Reason: Port Shutdown State Machine Type is Feature Conf TLV Tx Status is enabled 23 Input Conf TLV Pkts, 47 Output Conf TLV Pkts, 0 Error Conf TLV Pkts DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS. advertise dcbx-tlv On a DCBX port with a manual role, configure the PFC and ETS TLVs advertised to DCBX peers.
PAGE 487
dcbx port-role Configure the DCBX port role the interface uses to exchange DCB information. Syntax dcbx port-role {config-source | auto-downstream | auto-upstream | manual} To remove DCBX port role, use the no dcbx port-role {config-source | auto-downstream | auto-upstream | manual} command. Parameters Defaults config-source | Enter the DCBX port role, where: auto-downstream ● config-source: configures the port to serve as the configuration source on | auto-upstream | the switch.
PAGE 488
● cee: configures the port to use CDD (Intel 1.01). ● ieee-v2: configures the port to use IEEE 802.1az (Draft 2.5). Defaults Auto Command Modes INTERFACE PROTOCOL LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 489
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. fcoe priority-bits Configure the FCoE priority advertised for the FCoE protocol in application priority TLVs.
PAGE 490
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 491
Usage Information Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. To clear DCBX frame counters, use the clear dcbx counters interface stack-unit/port command. The following describes the show interface dcbx detail command shown in the following example. Field Description Interface Interface type with chassis slot and port number. Port-Role Configured the DCBX port role: auto-upstream, auto-downstream, config-source, or manual.
PAGE 492
Field Description Peer DCBX Sequence number transmitted in Control TLVs received from the peer device. Status: Sequence Number Peer DCBX Acknowledgement number transmitted in Control TLVs received from the peer Status: device. Acknowledgment Number Example Total DCBX Frames transmitted Number of DCBX frames sent from the local port. Total DCBX Frames received Number of DCBX frames received from the remote peer port. Total DCBX Frame errors Number of DCBX frames with errors received.
PAGE 493
dcb-map Create a DCB map to configure priority flow control (PFC) and enhanced transmission selection (ETS) on Ethernet ports that support converged Ethernet traffic. Apply the DCB map to an Ethernet interface. Syntax Parameters Defaults dcb-map map-nameTo remove a DCB map from an ethernet interface, use the no dcb-map command. map-name Enter a DCB map name. The maximum number of alphanumeric characters is 32. None.
PAGE 494
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.3(0.0) Introduced on the S4810, S6000 platforms.
PAGE 495
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.0) Added support to configure peak and committed rate on the S6000 platform. 9.3(0.0) Introduced on the S4810, S6000 platforms.
PAGE 496
Usage Information The dcb-map stack-unit all stack-ports all command overwrites any previous DCB maps applied to stack ports. dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. Syntax dcb pfc-shared—buffer—size buffer-size Parameters Default buffer-size Enter a number in the range of 0 to 3399. The default is 1040KB. Command Modes CONFIGURATION mode Command History Usage Information This guide is platform-specific.
PAGE 497
Defaults 1040 KB. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.0) Introduced on the Z9100-ON and S6100-ON. Example dcb-buffer-threshold Configure the profile name for the DCB buffer threshold.
PAGE 498
priority Configure the priority for the PFC threshold to be allocated to the buffer space parameters. Syntax priority value buffer-size size pause-threshold threshold-value peakheadroom headroom-value resume-offset threshold-value shared-thresholdweight size Parameters priority Specify the priority of the queue for which the buffer space settings apply. value Enter a number in the range of 0 to 7 to denote the priority to be allocated to the dynamic buffer control mechanism.
PAGE 499
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms.
PAGE 500
space to be allocated for each priority and the pause or resume thresholds for the buffer. This method of configuration enables you to effectively manage and administer the behavior of lossless queues. Example DellEMC(conf-if-te-1/1/1/1)# dcb-policy buffer-threshold test dcb pfc-total-buffer-size Configure the total buffer size for PFC in kilobytes. Syntax dcb pfc-total—buffer—size buffer-size Parameters Default buffer-size Enter a number in the range of 0 to 3399. The default is 2656KB.
PAGE 501
1 0.3 DellEMC# 3399 2800 1040 1040 720 DellEMC(conf)#dcb pfc-total-buffer-size 2000 % Error: Total buffer size should not be less than the buffer consumed already in the system DellEMC(conf)# show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration. Syntax show running—config dcb-buffer-threshold Command Modes EXEC EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 502
Te 1/1/2 Te 1/1/2 Te 1/1/2 Te 1/1/2 Te 1/1/2 Te 1/1/2 DellEMC# Q2 Q3 Q4 Q5 Q6 Q7 NO NO NO NO NO NO - - - - - On interface on which PFC is enabled: DellEMC(conf)#do show interfaces tengigabitethernet 1/1/1/2 pfc buffer-threshold Interface TenGigabitEthernet 1/1/1/2 Interface Queue# Lossless Buffer-size Pause-threshold Resume-offset Shared Threshold (KB) (KB) (KB) Weight --------------------------------------------------------------------------------------------Te 1/1/1/2 Q0 NO Te 1/1/1/2 Q1 NO Te 1/
PAGE 503
Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process. For example, you can assign a higher priority for time-sensitive applications and a lower priority for other services, such as file transfers.
PAGE 504
12 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 505
on the flash; if the flash is out of memory, the coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
PAGE 506
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 507
Usage Information Version Description 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented. DellEMC#offline stack-unit 1 Warning - Taking unit offline for running diagnostics will make it operationally down, causing traffic disruption through the unit.
PAGE 508
Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 509
Related Commands ● show hardware stack-unit — display the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
PAGE 510
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command. hardware watchdog To trigger a reboot and restart the system, set the watchdog timer.
PAGE 511
Usage Information This command enables a hardware watchdog mechanism that automatically reboots a Dell EMC Networking OS switch or router with a single unresponsive unit. This behavior is a last-resort mechanism that is intended to prevent a manual power cycle. show hardware mac Display MAC ACL entries for the specified stack-unit, port-pipe and pipeline ID.
PAGE 512
Parameters acl | qos Enter either the keyword acl or the keyword qos to select between ACL or QoS data. stack-unit Enter the keywords stack-unit then a number to select a stack ID. number port-set 0–0 Enter the keyword port-set with a port-pipe number. The range is from 0 to 0. pipeline pipeline- Enter the keyword pipeline with a pipeline number to display the MAC ACL number entries specific to the pipeline number. The range is from 0 to 3.
PAGE 513
cpu party-bus statistics Enter the keywords cpu party-bus statistics, to display the Management plane input/output counter statistics of the pseudo party bus interface. cpu satainterface statistics Enter the keywords cpu sata-interface statistics to display the sata interface error counter statistics. drops [unit unitnumber ] Enter the keyword drops to display internal drops on the selected stack member.
PAGE 514
noMhdr :0 noMbuf :0 noClus :0 recvd :0 dropped :0 recvToNet :0 rxError :0 rxFwdError :0 rxDatapathErr :0 rxPkt(COS0 ) :0 rxPkt(COS1 ) :0 rxPkt(COS2 ) :0 rxPkt(COS3 ) :0 rxPkt(COS4 ) :0 rxPkt(COS5 ) :0 rxPkt(COS6 ) :0 rxPkt(COS7 ) :0 rxPkt(COS8 ) :0 rxPkt(COS9 ) :0 rxPkt(COS10) :0 rxPkt(COS11) :0 rxPkt(UNIT0) :0 transmitted :0 txRequested :0 noTxDesc :0 txError :0 txReqTooLarge :0 txInternalError :0 txDatapathErr :0 txPkt(COS0 ) :0 txPkt(COS1 ) :0 txPkt(COS2 ) :0 txPkt(COS3 ) :0 txPkt(COS4 ) :0 txPkt(COS5 )
PAGE 515
0 0 0 0 EgressDrops 0 0 0 0 0 0 0 0 [output truncated] Example (PortStats) 0 0 DellEMC# show hardware stack-unit 1 unit 0 port-stats ena/ speed/ link auto STP port link Lns duplex scan neg? state pause discrd ce0 up 4 100G FD SW No Forward Tag xe0 !ena 1 25G FD None No Disable TX RX None xe1 !ena 1 50G FD None No Disable TX RX None xe2 !ena 1 25G FD None No Disable TX RX None ce1 up 4 100G FD SW No Forward Tag xe3 !ena 1 25G FD None No Disable TX RX None xe4 !ena 1 50G FD None No Disable TX RX None xe5 !e
PAGE 516
0x3880400a ASF_CREDIT_THRESH_HI.xe77 0x3880401a ASF_CREDIT_THRESH_HI.xe78 0x3880400b ASF_CREDIT_THRESH_HI.
PAGE 517
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - Unicast Frame Counter Multicast Frame Counter Broadcast Frame Counter Byte Counter Control Frame Counter Pause Control Frame Counter Oversized Frame Counter Jabber Counter VLAN Tag Frame Counter Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame Priority 2 PFC Frame Priority 3 PFC Frame Priority 4 PFC Frame Priority 5 PFC Frame
PAGE 518
show hardware stack-unit buffer Display the counters for the specified port, minimum guaranteed buffer of a priority-group, and the shared buffer.
PAGE 519
Field Description for Unit 0 Port 1 priority-group 0 Max Shared Limit Maximum shared buffer space allotted to the specific port for the corresponding stack unit Example Default Packet Buffer allocate for the prioritygroup The default packet buffer size in KB that is associated with the particular priority group Accounted Packet Buffer Shared buffer space that is in use by the packets DellEMC# show hardware stack-unit 1 buffer unit 0 port 1 priority-group 0 buffer-info ----- Buffer Accounting Stats f
PAGE 520
Used Packet Buffer: 0 ----- Buffer Stats for Interface Te 1/1/2/1 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Te 1/1/3/1 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Te 1/1/4/1 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 ----- Buffer Stats for Interface Te 1/1/5/1 Queue
PAGE 521
EXEC Privilege Command History Usage Information Example Version Description 9.11(0.0) Introduced on the S6000, S6000–ON, S6100–ON and Z9100–ON. Use this command to view the buffer details of lossy and lossless traffic in the service pool. Use the keyword detail buffer-info to view the buffer details allocated for each MMU unit.
PAGE 522
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information.
PAGE 523
MCAST MCAST MCAST MCAST Example displaying egress queue-level snapshot for unicast packets for the specific interface 6 7 8 9 0 0 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface hundredGigE 1/10 queue ucast 0 Stack-unit 1 unit: 0 port: 34 (interface Hu 1/10) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface hundredGigE 1/10 queue ucast all Stack-unit 1 un
PAGE 524
Stack-unit 1 unit: 0 port: 34 (interface Hu 1/10) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 Example showing buffer snap shot details for head room pool DellEMC#show hardware buffer-stats-snapshot resource headroom-pool --------------------------------------HP# PEAK USE COUNT(CELLS) --------------------------------------0 0 1 0 2 0 3 0 DellEMC# DellEMC#show hardware buffer-stats-snapshot resourc
PAGE 525
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 526
RX - Debug Counter 2 0 show hardware drops Displays internal drops on the specified interface or for a range of interface. Syntax show hardware drops interface interface Parameters drops Enter the keyword drops to display internal drops. interface Enter any of the following keywords and the interface or interface range information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 527
Example displaying internal drops Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.5 Added i2c statistics and sata-interfaces statistics. 8.3.11.4 Added user port information. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
PAGE 528
Ingress FEC uncorrected code words: 0 --- Error Ratio Counters --Ingress preFEC Bit Error Ratio: 0.0E0 Ingress FCS Drops Error Ratio : 0.
PAGE 529
show hardware system-flow Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe. Syntax Parameters show hardware system-flow stack-unit id port-set number [counters | pipeline pipeline-number] stack-unit id Enter the keywords stack-unit to select a stack member ID. port-set number Enter the keywords port-set with a port-pipe number. [counters | pipeline pipeline- (OPTIONAL) Enter the keyword counters for the specified port-pipe.
PAGE 530
DATA=0x00000001 ffffffff MASK=0x00000001 ffffffff HiGig Part:0 Offset0: 150 Width0: 2 DATA=0x00000000 MASK=0x00000001 action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)} action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)} action={act=CosQCpuNew, param0=7(0x7), param1=0(0), param2=0(0), param3=0(0)} action={act=CopyToCpu, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)} policer= statistics={stat id 1 slice = 8 idx=3 entries=1}{GreenPackets}{GreenBytes} ###
PAGE 531
show hardware stack-unit buffer-stats-snapshot View the buffer statistics tracking resource information without polling details and historical snapshots. Syntax Parameters show hardware stack-unit stack-unit-number buffer-stats-snapshot unit number resource X stack-unit stack- Unique ID of the stack unit to select a particular stack member and then enter unit-number one of the following command options to display a collection of data based on the option entered. The range is 0 to 11.
PAGE 532
show hardware stack-unit buffer-stats-snapshot (Total Buffer Information) View the buffer statistics tracking resource information depending on the type of buffer information, such as device-level details, port-level counters, queue-based snapshots, or priority group-level snapshot in the egress and ingress direction of traffic.
PAGE 533
Unit 0 unit: 0 port: 1 (interface Fo 0/0) -------------------------------------------------PG# PRIORITIES SHARED CELLS HEADROOM CELLS -------------------------------------------------7 0-2,5 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 0/0 priority-group 7 Unit 0 unit: 0 port: 1 (interface Fo 0/0) -------------------------------------------------PG# PRIORITIES SHARED CELLS HEADROOM CELLS -------------------------------------------------0 0 0 1 0 0 2 0 0 3 7 0 0 4 6 0 0 5 4 0
PAGE 534
13 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 535
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP.
PAGE 536
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 537
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific.
PAGE 538
Parameters Defaults address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 539
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. excluded-address Prevent the server from leasing an address or range of addresses in the pool.
PAGE 540
hardware-address For manual configurations, specify the client hardware address. Syntax hardware-address address Parameters Defaults address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 541
Usage Information When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.3 or later, the system converts the DHCP CONFIGURATION host command in the running configuration to the hostaddress command. If you downgrade the Dell EMC Networking OS from version 9.14.1.3 or later to an earlier version, any existing host-address command is deleted from the running configuration. If you want to create manual DHCP bindings, use the host command. ip dhcp server Enable DHCP server globally.
PAGE 542
Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 543
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell EMC Networking recommends specifying clients as hybrid.
PAGE 544
network Specify the range of addresses in an address pool. Syntax network network /prefix-length Parameters Defaults network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 545
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 546
show ip dhcp configuration Display the DHCP configuration. Syntax show ip dhcp configuration [global | pool name] Parameters Defaults pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 547
show ip dhcp conflict Display the address conflict log. Syntax Parameters Defaults show ip dhcp conflict address address Display a particular conflict log entry. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 548
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms.
PAGE 549
Related Commands ● arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table. arp inspection-limit Configure dynamic ARP inspection rate-limit to verify the rate of ARP packet received in a port on a specific interval. Syntax arp inspection-limit {rate pps [interval seconds]} Defaults None Command Modes INTERFACE CONFIGURATION Parameters Command History rate pps Enter the keyword rate then the packet per second (pps) value.
PAGE 550
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. ● arp inspection — enable dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. Syntax clear ip dhcp snooping {binding | source-address-validation discardcounters [interface interface]} Parameters binding Clears the binding table.
PAGE 551
Example Version Description 9.6(0.0) Added the keywords discard-counters, interface, and the variable interface on the S4810, S4820T, S5000, S6000, Z9000, Z9500. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 552
Example DellEMC# clear ipv6 dhcp snooping? binding Clear the snooping binding database ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] Parameters Defaults remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82. remote-id port Enter the keywords remote-id port to configure the port as the remote id in option–82.
PAGE 553
Version Description 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 554
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 555
Defaults vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 556
Related Commands ● show ip dhcp snooping — display the contents of the DHCP binding table. IPv6 DHCP Snooping Binding Create a static DHCP snooping binding entry in the snooping database.
PAGE 557
ip dhcp snooping database Delay writing the binding table for a specified time. Syntax Parameters Defaults ip dhcp snooping database write-delay minutes minutes The range is from 5 to 21600. None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 558
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping database renew Renew the binding table.
PAGE 559
Defaults None Command Modes ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 560
ipv6 dhcp snooping trust Configure an interface as trusted for DHCP snooping. Syntax [no] ipv6 dhcp snooping trust To disable dhcp snooping trusted capability on this interface, use the no ipv6 dhcp snooping trust command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 561
Usage Information Version Description 9.6(0.0) Added the vlan keyword and the vlan-id variable . Introduced support for SAV on port channels interfaces. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Added the keyword ipmac. 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 562
Example Version Description 9.11(2.0P0) Introduced the circuit-id attribute in the command. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 563
Command Modes ● CONFIGURATION ● INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface.
PAGE 564
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 565
Version Description 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
PAGE 566
ipv6-address Default Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Enhanced to support non-default VRF configuration for DHCPv6 helper address. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 567
Parameters Description ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 568
permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) permit vlan 10 host 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) permit vlan 10 host 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) ipmac-vlan sav access-list on Port-channel 10 on stack-unit 2 Total cam count 5 permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) permit vlan 10 host 1.1.1.
PAGE 569
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 570
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Example Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.
PAGE 571
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. DellEMC(conf)# ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 572
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrfname] name ip-address command.
PAGE 573
Defaults None Command Modes EXEC Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 574
14 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • ecmp-group hash-algorithm ip ecmp-group ip ecmp weighted link-bundle-distribution trigger-threshold link-bundle-monitor enable ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold.
PAGE 575
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810.
PAGE 576
● xor4: Use CRC16_BISYNC_AND_XOR4 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor4 ● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR hg { crc16 | crc16cc | Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices: crc32MSB | ● crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) crc32LSB | xor1 | ● crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT po
PAGE 577
Usage Information Version Description 9.9(0.0) Added flow-based-hashing support for hashing on ECMP for S4820T, S6000, S4048 and Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.
PAGE 578
ip ecmp-group Enable and specify the maximum number of ecmp that the L3 CAM hold for a route, By default, when maximum paths are not configured, the CAM can hold a maximum of 16 ecmp per route. Syntax ip ecmp-group {maximum-paths | {number} {path-fallback} To negate a command, use the no ip ecmp-group maximum-paths {number} command. Parameters Defaults maximum-paths Specify the maximum number of ECMP for a route. The range is 2 to 64.
PAGE 579
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. Enabling this CLI would inform the FIB to re-program the destination prefix paths with weights in the HW/CAM on the fly.
PAGE 580
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. link-bundle-monitor enable Provides a mechanism to enable monitoring of traffic distribution on an ECMP link bundle. Syntax link-bundle-monitor enable To exit from ECMP group mode, use the exit command.
PAGE 581
15 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Topics: • • • • • • • load-balance ingress-port enable load-balance flexhash lacp fast-switchover show issu clients show issu detail show issu status encapsulation dot1q load-balance ingress-port enable Enable the Flex hash functionality. This utility is supported on the platform. Syntax load-balance ingress-port enable To disable the Flex hash capability, use the no version of this command.
PAGE 582
load-balance flexhash Specify the parameters for the Flex Hash mechanism, such as whether IPv4 or IPv6 packets must be subject to Flex Hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name.
PAGE 583
lacp fast-switchover Cause the physical ports to be aggregated faster by configuring this capability in a port-channel on both the nodes that are members of a port-channel. Syntax lacp fast-switchover To disable the capability of faster aggregation of the member ports of a LAG or a port-channel bundle, use the no version of this command. Defaults Not configured Command Modes INTERFACE (conf-if-po-number) Command History Usage Information Version Description 9.10(0.
PAGE 584
7 ISSU IPMGR Client 8 ISSU MRTM Client 9 ISSU LC Client 10 ISSU Mac Manager Client 11 ISSU LACP Client 12 ISSU NDPM Client 13 ISSU XSTP Client 14 ISSU BGP Client 15 ISSU Mirror Client 16 ISSU SupportAssist Client 17 ISSU Tunnel Manger Client DellEMC# YES Configuration audit completed NO ---NO ---YES Configuration audit completed YES Configuration audit completed YES Configuration audit completed YES Configuration audit completed NO ---YES Configuration audit completed YES Configuration audit completed YES
PAGE 585
ISSU SupportAssist Client DellEMC# show issu status Shows the current state of warmboot and a summary of the number of clients registered. Syntax show issu status Parameters N/A Defaults N/A Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.
PAGE 586
Usage Information 586 To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction. At the egress interface, the VLAN ID is appended to the packet and transmitted out of the interface as a tagged packet with the dot1Q value preserved.
PAGE 587
16 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE end-device and an FCF.
PAGE 588
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface.
PAGE 589
info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 590
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 591
0 ipmacacl 0 vman-qos 0 fcoeacl 2 etsacl 1 iscsi 2 DellEMC(conf)#feature fip-snooping fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN. Syntax fip-snooping enable To disable the FIP snooping feature on all or a specified VLAN, use the no fip-snooping enable command. Defaults FIP snooping is disabled on all VLANs. Command Modes ● CONFIGURATION ● VLAN INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 592
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. fip-snooping max-sessions-per-enodemac Configure the maximum session limit per ENode MAC address.
PAGE 593
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links.
PAGE 594
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 595
Example Field Description ENode Interface Slot/ port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. VLAN VLAN ID number the session uses. FC-ID Fibre Channel session ID the FCF assigns.
PAGE 596
Example DellEMC# show fip-snooping fcf FCF MAC FCF Interface VLAN FC-MAP FKA_ADV_PERIOD No. of Enodes ------- ------------- ---- ------ -------------- ------------54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels.
PAGE 597
Field Description Number of FLOGO Number of FIP-snoop FLOGO frames received on the interface Number of ENode Number of FIP-snoop ENode keep-alive frames received on the interface. Keep Alives Number of VN Port Keep Alives Number of FIP-snoop VN port (Virtual N-port) keep-alive frames received on the interface Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface.
PAGE 598
Number of FLOGO Rejects :0 Number of CVL :0 Number of FCF Discovery Timeouts :0 Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int tengigabitethernet 1/1/1/1 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of FLOGI :1 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :4416 Number of VN Port Keep Al
PAGE 599
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 600
show fips status Display the FIPs status on the platform. Syntax show fips status Defaults none Command Modes EXEC Command History 600 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.
PAGE 601
17 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
PAGE 602
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 603
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 604
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol.
PAGE 605
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 606
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration.
PAGE 607
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. mode Set the Master or Transit mode of the ring. Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters Defaults master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode.
PAGE 608
To exit the ring protocol, use the no protocol frrp {ring-id} command. Parameters Defaults ring-id Enter the ring identification number. The range is from 1 to 255. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 609
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 610
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
PAGE 611
Example (2 Summary) DellEMC# show frrp 2 summary DellEMC#show frrp 2 summary Ring-ID State Mode Ctrl_Vlan Member_Vlans ----------------------------------------------2 Up Master 2 11-20, 25, 27-30 DellEMC# Related Commands ● protocol frrp — enter the resilient ring protocol and designate a ring identification. timer Set the hello interval or dead interval for the Ring control packets.
PAGE 612
Usage Information 612 Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. The hello interval command is the interval at which ring frames are generated from the primary interface of the master node. The dead interval command is the time that elapses before a time-out occurs.
PAGE 613
18 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 614
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax clear gvrp statistics interface interface Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 615
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters Defaults config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 616
disable Globally disable GVRP. Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 617
leave Enter the keyword leave then the number of milliseconds to configure the leave time. The range is from 100 to 2147483647 milliseconds. The default is 600 milliseconds. NOTE: Designate the milliseconds in multiples of 100. leave-all Enter the keywords leave-all then the number of milliseconds to configure the leave-all time. The range is from 100 to 2147483647 milliseconds. The default is 1000 milliseconds. NOTE: Designate the milliseconds in multiples of 100. Defaults As above.
PAGE 618
gvrp enable Enable GVRP on physical interfaces and LAGs. Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 619
Command Modes CONFIGURATION-INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 620
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 621
● protocol gvrp — access the GVRP protocol. show garp timers Display the GARP timer settings for sending GARP messages. Syntax show garp timers Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 622
Parameters Defaults brief (OPTIONAL) Enter the keyword brief to display a brief summary of the GVRP configuration. interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 623
Te 1/1/2/4 Disabled DellEMC# show gvrp brief Related Commands No ● show gvrp statistics — display the GVRP statistics. show gvrp statistics Display the GVRP configuration statistics.
PAGE 624
● The Attribute Type of the attribute that was being parsed was not the GVRP VID Attribute Type (0x01). ● The attribute that was being parsed had an invalid attribute length. ● The attribute that was being parsed had an invalid GARP event. ● The attribute that was being parsed had an invalid VLAN ID. The valid range is from 1 to 4095. A failed registration can occur for the following reasons: ● Join requests were received on a port that was blocked from learning dynamic VLANs (GVRP Blocking state).
PAGE 625
19 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 626
Table 4. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 626 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 627
20 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
PAGE 628
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 629
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 630
Command Modes INTERFACE (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 631
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database.
PAGE 632
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends.
PAGE 633
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.0 Introduced on the C-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. E-Series legacy command.
PAGE 634
Version Description 7.5.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the S-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. 7.5.1.0 Introduced on the C-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. E-Series legacy command. ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list.
PAGE 635
Usage Information Mapping applies to both v1 and v2 IGMP joins; any updates to the ACL are reflected in the IGMP groups. You may not use extended access lists with this command. When you configure a static SSM map and the router cannot find any matching access lists, the router continues to accept (*,G) groups. Related Commands ● ip access-list standard — create a standard access list to filter based on IP address. ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3.
PAGE 636
show ip igmp groups View the IGMP groups. Syntax show ip igmp [vrf vrf-name] groups [group-address [detail] | detail | interface [group-address [detail]]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only.
PAGE 637
Version Description 7.6.1.0 Introduced on the S-Series and C-Series. 7.5.1.0 Expanded to support the detail option. E-Series legacy command. Usage Information This command displays the IGMP database, including configured entries for either all groups on all interfaces, all groups on specific interfaces, or specific groups on specific interfaces. The following describes the show ip igmp groups command shown in the following example.
PAGE 638
Last reporter Group source list Source address 65.0.0.1 65.0.0.2 65.0.0.3 65.0.0.4 65.0.0.5 35.0.0.2 Expires 00:01:22 00:01:22 00:01:22 00:01:22 00:01:22 show ip igmp interface View information on the interfaces participating in IGMP. Syntax show ip igmp [vrf vrf-name] interface [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF.
PAGE 639
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information Example Example (VRF) IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. The show ip igmp interface command does not display information corresponding to the loopback interfaces.
PAGE 640
show ip igmp ssm-map Display is a list of groups that are currently in the IGMP group table and contain SSM mapped sources. Syntax show ip igmp [vrf vrf-name] ssm-map [group] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group (OPTIONAL) Enter the multicast group address in the form A.B.C.
PAGE 641
IGMP Snooping Commands Dell EMC Networking OS supports IGMP Snooping version 2 and 3 on all Dell EMC Networking systems. Important Points to Remember for IGMP Snooping ● Dell EMC Networking OS supports version 1, version 2, and version 3 hosts. ● Dell EMC Networking OS IGMP snooping implementation is based on IP multicast address (not based on Layer 2 multicast mac address) and the IGMP snooping entries are in Layer 3 flow table not in Layer 2 forwarding information base (FIB).
PAGE 642
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 643
Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 644
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. To enable IGMP snooping, enter this command. When you enable this command from CONFIGURATION mode, IGMP snooping enables on all VLAN interfaces (except the default VLAN). NOTE: Execute the no shutdown command on the VLAN interface for IGMP Snooping to function. ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN.
PAGE 645
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to GroupLeave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters Defaults milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
PAGE 646
To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 647
ip igmp snooping querier Enable IGMP querier processing for the VLAN interface. Syntax ip igmp snooping querier To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 648
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 649
Example DellEMC# show ip igmp snooping groups Total Number of Groups: 1 IGMP Connected Group Membership Group Address Interface Mode Reporter 225.1.1.1 Vlan 10 IGMPv2-Compat Member Ports: Te 1/1/1/1 DellEMC# Uptime Expires Last 00:00:07 00:02:09 1.1.1.2 show ip igmp snooping mrouter Display multicast router interfaces. Syntax Parameters show ip igmp snooping mrouter [vlan number] vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094.
PAGE 650
Related Commands 650 ● ip igmp snooping mrouter — configure a static connection to the multicast router. ● show ip igmp groups — view groups.
PAGE 651
21 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • Basic Interface Commands Port Channel Commands Enhanced Validation of Interface Ranges ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 652
● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4. ● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport].
PAGE 653
Example Related Commands DellEMC# clear counters Clear counters on all interfaces [confirm] DellEMC# ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 654
Example Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC# clear dampening tegigabitethernet 1/1/3/1 Clear dampening counters on TeGi 1/1/3/1 [confirm] y DellEMC# ● show interfaces dampening — display interface dampening information. ● dampening — configure dampening on an interface. dampening Configure dampening on an interface.
PAGE 655
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. With each flap, Dell EMC Networking OS penalizes the interface by assigning a penalty (1024) that decays exponentially depending on the configured half-life. After the accumulated penalty exceeds the suppress threshold value, the interface moves to the Error-Disabled state.
PAGE 656
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Modified for E-Series: Revised from 78 to 240 characters. Important Points to Remember: ● To use special characters as a part of the description string, you must enclose the whole string in double quotes.
PAGE 657
Usage Information Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048-ON, S4048-ON, S5000, S6000, S6000– ON, and Z9500. Use the default interface command to set a Gigabit Ethernet, 10- Gigabit Ethernet, or 40-Gigabit Ethernet interface to its factory-default state. By default, a physical interface is disabled (shutdown) with no assigned IP address or switchport (no ip address).
PAGE 658
Usage Information To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction. At the egress interface, the VLAN ID is appended to the packet and transmitted out of the interface as a tagged packet with the dot1Q value preserved.
PAGE 659
Parameters Defaults interval seconds Enter the keyword interval and the number of seconds to recover the interface from Err-disabled state. The range is from 30 to 86,400 seconds. The default is 300 seconds. 300 seconds. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 660
fec enable Enable FEC on the interface. Syntax fec enable To disable FEC, use the no fec enable command. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Enabled on 25G and 50G interfaces on the Z9100–ON by default.
PAGE 661
Defaults rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received. tx off Enter the keywords tx off so that flow control frames are not sent from this port to the connected device when a higher rate of traffic is received. pause-threshold Enter the buffer threshold limit for generating PAUSE frames.
PAGE 662
the traffic. Eventually this reduces the buffer usage. When the buffer usage drops by the value specified in the “resume-threshold”, the port again sends a PAUSE frame with 0 as wait-time. This results in resume of the paused traffic flow. Important Points to Remember ● Do not enable tx pause when buffer carving is enabled. For information and assistance, consult Dell EMC Networking TAC. ● The only configuration applicable to half duplex ports is rx off tx off.
PAGE 663
on on off on on on off on off off on on off on off on LocNegRx off off off off LocNegTx RemNegRx RemNegTx off off off off off off off off off off off off off off off off off off on off off off on off off off off off off on on on off off on on off off on on off on on on off off on on off off on on off off on on off off on on interface Configure a physical or virtual interface on the switch.
PAGE 664
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 665
Related Commands ● ● ● ● interface interface interface interface loopback — configure a Loopback interface. null — configure a Null interface. port-channel — configure a port channel. vlan — configure a VLAN. interface group Create or delete group of VLANs with a single command. You can also use this command to apply a set of configurations on a group of interfaces.
PAGE 666
The configuration commands inside the group context will be the similar to that of the existing range command. Note: For release 9.4(0.0), the group command is supported only for VLANs and physical interfaces. Example DellEMC(conf)# interface group ? fortyGigE FortyGigabit Ethernet interface gigabitethernet GigabitEthernet interface IEEE 802.
PAGE 667
Example Related Commands DellEMC(conf)# interface loopback 1655 DellEMC(conf-if-lo-1655)# ● ● ● ● interface interface interface interface — configure a physical interface. null — configure a Null interface. port-channel — configure a port channel. vlan — configure a VLAN. interface managementEthernet Configure the Management port on the system (either the Primary or Standby RPM). Syntax Parameters Defaults interface managementEthernet slot/port slot/port Not configured.
PAGE 668
interface null Configure a Null interface on the switch. Syntax interface null number Parameters Defaults number Enter zero (0) as the Null interface number. Not configured; number = 0 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 669
interface range This command permits configuration of a range of interfaces to which subsequent commands are applied (bulk configuration). Using the interface range command, you can enter identical commands for a range of interface. Syntax Parameters Defaults interface range interface {[stack/]slot/port[/subport] | port} — {[stack/]slot/port[/subport] | port}, interface {[stack/]slot/port[subport] | port} — {[stack/]slot/port[subport] | port},...
PAGE 670
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. When creating an interface range, interfaces appear in the order they are entered; they are not sorted.
PAGE 671
Example (Multiple Ports) Example (Overlapping Ports) Usage Information DellEMC(conf)# interface range tengigabitethernet 1/1/1/1 - 1/1/4/3, tengigabitethernet 1/1/3/2 - 1/1/4/1 DellEMC(conf-if-range-te-1/1/1/1-1/1/4/3)# DellEMC(conf)# interface range tengigabitethernet 1/1/1/1 - 1/1/3/1, tengigabitethernet 1/1/1/1 - 1/1/4/3 DellEMC(conf-if-range-te-1/1/1/1-1/1/4/3)# Only VLAN and port-channel interfaces created using the interface vlan and interface portchannel commands can be used in the interface range
PAGE 672
Related Commands ● ● ● ● ● interface port-channel — configure a port channel group. interface vlan — configure a VLAN interface. show config (from INTERFACE RANGE mode) — display the bulk configuration interfaces. show range — display the bulk configuration ranges. interface range macro (define) — define a macro for an interface-range. interface range macro (define) Defines a macro for an interface range and then saves the macro in the running configuration.
PAGE 673
Example (Single Range) Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This example shows how to define an interface range macro named test. Execute the show runningconfig command to display the macro definition.
PAGE 674
Example (Single Range) Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 675
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Introduced on the S4810; added support for OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. For more information about VLANs and the commands to configure them, see Virtual LAN (VLAN) Commands. FTP, TFTP, and SNMP operations are not supported on a VLAN.
PAGE 676
intf-type cr2 autoneg Enable Clause 73 autonegotiation on a 50G CR2 interface. Syntax intf-type cr2 autoneg To disable Clause 73 autonegotiation on a 50G CR2 interface, use the no intf-type cr2 autoneg command. Defaults Not configured Command Modes INTERFACE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced on the Z9100–ON.
PAGE 677
● interface loopback — configure a loopback interface. ● interface null — configure a null interface. ● interface port-channel — configure a port channel group. keepalive Send keepalive packets periodically to keep an interface alive when it is not transmitting data. Syntax keepalive To stop sending keepalive packets, use the no keepalive command. Defaults Enabled. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 678
● For the Management interface on the stack-unit, enter the keyword managementEthernet then the slot/port information. ● For a port channel interface, enter the keyword port-channel and then a number. ● For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 679
Example (Single Interface) Key Description monitor time Displays the amount of time since the monitor interface command was entered. time Displays the amount of time the chassis is up (since last reboot). m Change the view from a single interface to all interfaces on the line card or visaversa. c Refresh the view. b Change the counters displayed from Packets on the interface to Bytes.
PAGE 680
Te 1/1/2/4 Up Te 1/1/3/1 Up Te 1/1/3/2 Up Te 1/1/3/3 Up Te 1/1/3/4 Up Te 1/1/4/1 Up Te 1/1/4/2 Up Te 1/1/4/3 Up Te 1/1/4/4 Up Te 1/1/5/1 Up Te 1/1/5/2 Up Te 1/1/5/3 Down Te 1/1/5/4 Up Te 1/1/6/1 Up Te 1/1/6/2 Up 1114221 Te 1/1/6/3 Up 523329 m - Change mode b - Display bytes l - Page up 61427 1 59960 62039 53 104239232 17740044091 372 7373849244 18182889225 44 7184747584 18182682056 0 3682 18182681434 43 6592378911 61349 55 86281941 59808 58 62060 59889 1 61616 0 0 14950126 0 0 0 0 0 0 62734 54 62766 60198
PAGE 681
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If the packet includes a Layer 2 header, the difference between the link MTU and IP MTU (ip mtu command) must be enough bytes to include the Layer 2 header. When you enter the no mtu command, Dell EMC Networking OS reduces the IP MTU value to 1536 bytes. Link MTU and IP MTU considerations for port channels and VLANs are as follows.
PAGE 682
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 683
forced-slave Force port to slave mode DellEMC(conf-if-autoneg)# Example (Configured) User Information DellEMC# show interfaces configured TenGigabitEthernet 1/1/3/4 is up, line protocol is up Hardware is DellEMCEth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.
PAGE 684
Usage Information Related Commands To disable the timer on an individual interface, use the no port-delay-restore command. To disable the timer on all ports globally, use the no port-delay-restore command in CONFIGURATION mode. port-delay-restore (Interface Mode) — allows a delayed bring up of all interfaces during switch boot up. port-delay-restore (Configuration Mode) Allows a delayed bring up of all interfaces during switch boot up.
PAGE 685
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 686
DellEMC(conf-if-te-1/1/1/1)# no portmode hybrid DellEMC(conf-if-vl-20)# rate-interval Configure the traffic sampling interval on the selected interface. Syntax rate-interval seconds Parameters Defaults seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds. NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value.
PAGE 687
rate-interval (Configuration Mode) Configure the traffic sampling interval for all physical and logical port-channel interfaces globally. The support to configure rate-interval globally enables you to modify the default interval rate for all physical and logical interfaces at one time. Syntax rate-interval seconds Use the no rate-interval command to remove the sampling interval configuration. Parameters seconds Enter the number of seconds for which to collect traffic data.
PAGE 688
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 689
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 690
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel then the tunnel ID.
PAGE 691
Usage Information Version Description 9.1(0.0) Updated Management Ethernet output to include two global IPv6 addresses on S4810 and Z9000 and added output example showing OpenFlow instance ID. 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. 8.3.11.4 Output expanded to support eSR4 optics in Z9000. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 692
Line Description Last clearing... Displays the time when the show interfaces counters where cleared. Queuing strategy... States the packet queuing strategy. FIFO means first in first out.
PAGE 693
Flowcontrol rx off tx off ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1d18h54m Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 o
PAGE 694
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 695
Ethernet, two IPv6 addresses) ManagementEthernet 1/1 is up, line protocol is up Hardware is DellForce10Eth, address is 00:01:e8:a0:bf:f3 Current address is 00:01:e8:a0:bf:f3 Pluggable media not present Interface index is 302006472 Internet address is 10.16.130.
PAGE 696
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.
PAGE 697
Parameters interface (Optional) Enter one of the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 698
Example Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 699
Current address is 00:01:e8:4c:f2:82 Pluggable media not present Interface index is 34129154 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto, Mode auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 3w0d17h Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 5144 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttl
PAGE 700
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. stack-unit slot- number Defaults (OPTIONAL) Enter the keyword stack-unit then the slot number. The range is from 0 to 5. None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 701
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 702
Example Version Description 9.10(0.1) Introduced on the S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(1.0) Introduced on the Z9100-ON.
PAGE 703
stack-unit unit-id (OPTIONAL) Enter the keywords stack-unit then the stack member number. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.
PAGE 704
Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/1/3/1 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/1/4/1 802.1QTagged: True Vlan membership: Vlan 2 --More-Related Commands ● interface — configure a physical interface on the switch. ● show ip interface — display Layer 3 information about the interfaces. ● show interfaces transceiver — display the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number.
PAGE 705
Usage Information Version Description 9.11(0.0) Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000-ON, S6100, Z9500, S6010, and Z9100. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 706
Line Description Temp Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 707
Line Description Rx Power Present receiving (Rx) power of the SFP. This value is either average Rx power or OMA. This depends on the Rx Power measurement type displayed above. If this crosses Rx power alarm/warning thresholds, the Rx power high alarm/warning flag is set to true. If it falls below the low alarm/warning thresholds, the Rx power low alarm/warning flag is set to true. Data Ready state This field indicates that the transceiver has achieved power up and data is ready.
PAGE 708
Example Line Description Voltage Low Warning Flag This can be either true or false, depending on the Current Voltage value displayed above. Tx Bias Low Warning Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power Low Warning Flag This can be either true or false, depending on the Current Tx power value displayed above. Rx Power Low Warning Flag This can be either true or false, depending on the Current Rx power value displayed above.
PAGE 709
QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 4/7/1 4/7/1 4/7/1 4/7/1 4/7/1 4/7/1 4/7/1 4/7/1 4/7/1 TX4 RX1 RX2 RX3 RX4 TX1 TX2 TX3 TX4 Bias Current Power Power Power Power Power Power Power Power = = = = = = = = = 0.000mA -1.0193dBm -0.2415dBm -0.4528dBm -0.
PAGE 710
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4093 VLANs on E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced.
PAGE 711
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The shutdown command marks a physical interface as unavailable for traffic. To discover if an interface is disabled, use the show ip interface brief command. Disabled interfaces are listed as down. Disabling a VLAN or a port channel causes different behavior. When a VLAN is disabled, the Layer 3 functions within that VLAN are disabled. Layer 2 traffic continues to flow.
PAGE 712
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Added support for fanned–out 1 Gigabit SFP port. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Supported on LC-EH-GE-50P or the LC-EJ-GE-50P cards. 8.1.1.
PAGE 713
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 714
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Added support for dynamically fanning-out of interfaces on S6000.
PAGE 715
interface interface Defaults (OPTIONAL) Enter any of the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 716
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output. When you enter the switchport command, the interface is automatically added to the default VLAN.
PAGE 717
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 718
group Group two LAGs in a supergroup (“fate-sharing group” or “failover group”). Syntax group group_number port-channel number port-channel number To remove an existing LAG supergroup, use the no group group_number command. Parameters group_number Enter an integer from 1 to 32 that uniquely identifies this LAG fate-sharing group. port-channel Enter the keywords port-channel then an existing LAG number. Enter this keyword/variable combination twice, identifying the two paired LAGs.
PAGE 719
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the number of port channels to 4096. Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 720
● interface null — configure a null interface. ● interface vlan — configure a VLAN. ● shutdown — disable/enable the port channel. minimum-links Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the LAG to be also in “oper up” status. Syntax minimum-links number Parameters Defaults number Enter the number of links in a LAG that must be in “oper up” status. The range is from 1 to 16. The default is 1.
PAGE 721
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 722
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the number of port channels to 4096. Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.
PAGE 723
Example Field Description packets input... Displays the number of packets and bytes into the interface. Input 0 IP packets... Displays the number of packets with IP headers, VLAN tagged headers, and MPLS headers. The number of packets may not add correctly because a VLAN tagged IP packet counts as both a VLAN packet and an IP packet. 0 64-byte... Displays the size of packets and the number of those packets entering that interface. This information is displayed over two lines. Received 0...
PAGE 724
Example Field Description (untitled) Displays the status of the physical interfaces (up or down). ● In Layer 2 port channels, an * (asterisk) indicates which interface is the primary port of the port channel. The primary port sends out interface PDU. ● In Layer 3 port channels, the primary port is not indicated.
PAGE 725
vlan vlan-id Enter the keywords vlan then the VLAN-id. The range is from 0 to 4094. ether-type Enter the keywords ether-type in the XX:XX format. Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 726
1/1/1,fo 1/3/1, this configuration is considered valid. The comma-separated list is not required to be separated by spaces in between the ranges. You can associate multicast MAC or hardware addresses to an interface range and VLANs by using the mac-address-table static multicast-mac-address vlan vlan-id output-range interface command. ip http source-interface Specify an interface as the source interface for HTTP connections.
PAGE 727
22 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 728
• • • • • • • • show show show show show show show show ip management-route ipv6 management-route ip protocols ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters Defaults vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 729
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. You cannot use Class D or Class E IP addresses or zero IP address (0.
PAGE 730
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses.
PAGE 731
Beginning with Dell EMC Networking OS version 8.3.1.0, when a gratuitous ARP is received, Dell EMC Networking OS installs an ARP entry on all three CPUs. arp max-entries Enables you to configure the maximum number of ARP entries per VRF that are allowed for IPv4.. Syntax Parameters Defaults arp max-entries [vrf vrf-name] max-number vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows.
PAGE 732
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 733
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 734
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 735
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 736
clear ip route Clear one or all routes in the routing table. Syntax clear ip route [vrf vrf-name] {* | ip-address mask} Parameters vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to clear the routes corresponding to that VRF. * Enter an asterisk (*) to clear all learned IP routes. ip-address mask Enter a specific IP address and mask in dotted decimal format to clear that IP address from the routing table.
PAGE 737
clear tcp statistics Clear TCP counters. Syntax Parameters clear tcp statistics [all | cp] all Enter the keyword all to clear all TCP statistics maintained on all switch processors. cp (OPTIONAL) Enter the cp to clear only statistics from the Control Processor. rp (OPTIONAL) Enter the keyword rp to clear only the statistics from Route Processor. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 738
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 739
debug ip dhcp Enable debug information for dynamic host configuration protocol (DHCP) relay transactions and display the information on the console. Syntax debug ip dhcp To disable debug, use the no debug ip dhcp command. Defaults Debug disabled Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 740
00:12:40 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for 00:60:CF:20:7B:8C to 14.4.4.2 00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at interface 14.4.4.1 BOOTP Reply, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 113.3.3.17 00:12:42 : %RELAY-I-BOOTREPLY: Forwarded BOOTREPLY for 00:60:CF:20:7B:8C to 113.3.3.254 00:12:42 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.
PAGE 741
Example Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 742
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History Usage Information 742 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 743
Example Usage Information Field Description UDP src= Displays the source and destination ports for the UDP packets. ICMP type= Displays the ICMP type and code. IP Fragment States that it is a fragment and displays the unique number identifying the fragment (Ident) and the offset (in 8-byte units) of this fragment (fragment offset) from the beginning of the original datagram. IP: s=10.1.2.62 (local), d=10.1.2.
PAGE 744
icmp6-redirect enable Enable ICMP and ICMP6 redirects. Syntax icmp6-redirect enable Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description Legacy command Legacy command Usage Information Use this command to notify hosts on the same network that a better route is available for a specific destination.
PAGE 745
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You must be in INTERFACE mode before you add an IP address to an interface. Assign an IP address to an interface prior to entering ROUTER OSPF mode. ip directed-broadcast Enables the interface to receive directed broadcast packets.
PAGE 746
ip domain-list Configure names to complete unqualified host names. Syntax ip domain-list name To remove the name, use the no ip domain-list name command. Parameters Defaults name Enter a domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 747
ip domain-lookup To address resolution (that is, DNS), enable dynamic host-name. Syntax ip domain-lookup To disable DNS lookup, use the no ip domain-lookup command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 748
To remove the domain name, use the no ip domain-name command. Parameters Defaults name Enter one domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 749
Parameters Defaults ip-address Enter an IP address in dotted decimal format (A.B.C.D). Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 750
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 751
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 752
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 753
ipv6 icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv6 packets.
PAGE 754
address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output. The loopback address must be unique in a particular domain.
PAGE 755
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series. To avoid denial of service (DOS) attacks, keep the number of fragments allowed for re-assembly low. ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command.
PAGE 756
In a dual stack setup, the system sends both A (request for IPv4 — RFC 1035) and AAAA (request for IPv6 — RFC 3596) record requests to a DNS server even if only the ip name-server command is configured. ip proxy-arp Enable proxy ARP on an interface. Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History Related Commands 756 This guide is platform-specific.
PAGE 757
ip route Assign a static route to the switch. Syntax ip route [vrf vrf-name] ip-address mask {ip-address | interface [ipaddress]} [distance] [name description] [permanent] [tag tag-value] [vrf vrf-name] [weight weight-value] To delete a specific static route, use the no ip route destination mask command. To delete all routes matching a certain route, use the no ip route destination mask command.
PAGE 758
tag tag-value (OPTIONAL) Enter the keyword tag then a number to assign to the route. The range is from 1 to 4294967295. vrf vrf-name Enter the keyword vrf followed by the name of the VRF. Use this VRF option after the next hop to specify which VRF the next hop belongs to. This setting is used in route leaking cases. See “R”oute Leaking VRFs” in the Virtual Routing and Forwarding (VRF) section of the Configuration guide. weight weight- Enter the keyword weight followed by a weight value.
PAGE 759
● ● ● ● When When When When the interface goes down, Dell EMC Networking OS withdraws the route. the interface comes up, Dell EMC Networking OS re-installs the route. recursive resolution is “broken,” Dell EMC Networking OS withdraws the route. recursive resolution is satisfied, Dell EMC Networking OS re-installs the route. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect.
PAGE 760
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip tcp initial-time Define the wait duration in seconds for the TCP connection to be established. This command is supported on the , , , and platforms.
PAGE 761
Defaults Parameters None vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable catch-all routes corresponding to that VRF. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 762
route prefixes are cleared from RTM DellEMC(conf)#no ip unicast-host-route show ip tcp initial-time Displays the interval that you configured for the device to wait before the TCP connection is attempted to be established. Syntax show ip tcp initial-time Command Modes EXEC EXEC Privilege Command History Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.7(0.1) Introduced on the S3048-ON. 9.7(0.1) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.
PAGE 763
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. load-balance By default, for C-Series and S-Series, Dell EMC Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths.
PAGE 764
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 765
● vlan — Use vlan field in hash calculation. ● L4-source-port — Use IPv4 L4-source-port field in hash calculation. ● L4-dest-port — Use IPv4 L4-dest-port field in hash calculation. Defaults mac [ source-mac | source-port-id | source-moduleid | dest-mac | dest-port-id | dest-module-id | vlan | ethertype | source-destmac ] To use MAC key fields in hash computation, enter the keyword mac then one of the parameters: ● source-mac — Use source-mac field in hash calculation.
PAGE 766
To remove a static route, use the no management route command. Parameters ip-address mask Enter an IP address (dotted decimal format) and mask (/prefix format) of the destination subnet. ipv6-address prefix-length Enter an IPv6 address (x:x:x:x::x format) and mask (/prefix format) of the destination subnet. Enter the IPv6 address in the x:x:x:x::x format followed by the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 767
show arp Display the ARP table. Syntax Parameters show arp [vrf vrf-name] [interface interface | ip ip-address [mask] | macaddress mac-address [mac-address mask]] [retries] [static | dynamic] [inspection {database | statistics][summary] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF. NOTE: Use this attribute to start a BGP instance for either a specific address family corresponding to the default VRF or an IPv4 address family corresponding to a non-default VRF.
PAGE 768
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF and added usage information for the clear arp-cache command. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 769
Internet Internet Internet Internet Internet Internet Internet Internet Internet Example (Private VLAN) 192.2.1.251 192.2.1.250 192.2.1.251 192.2.1.250 192.2.1.249 192.2.1.248 192.2.1.247 192.2.1.246 192.2.1.
PAGE 770
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced.
PAGE 771
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. The following describes the show hosts command in the following example. Field Description Default domain... Displays the domain name (if configured). Name/address lookup... States if DNS is enabled on the system. ● If DNS is enabled, the Name/Address lookup is domain service. ● If DNS is not enabled, the Name/Address lookup is static mapping Name servers are... Lists the name servers, if configured.
PAGE 772
vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display CAM entries corresponding to that VRF. network mask [longer-prefixes [ecmp-group detail]] (OPTIONAL) Enter the IP address and mask of a route to CAM entries for that route only. You can enter one of the following keywords to filter results. ● Enter the keyword longer-prefixes to view routes with a common prefix. ● Enter the keyword ecmp-group detail to view the ECMP group index.
PAGE 773
Example Field Description Port Displays the egress interface. ● CP = control processor ● Gi = Gigabit Ethernet interface ● Te = 10–Gigabit Ethernet interface DellEMC# show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port -------------------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Te 1/1/1/1 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP 1.1.1.
PAGE 774
● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 775
Example (Show command output with Weighted ECMP Enabled) DellEMC# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC RC W -----------------------------------------------------------------------------0.0.0.0/0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - 1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - 1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 - - The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp weighted command.
PAGE 776
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 777
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 778
IP MTU is 1500 bytes Directed broadcast forwarding is disabled Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# DellEMC# show ip interface port-channel 128 Port-channel 128 is down, line protocol is down Internet address is 10.1.1.1/16 Broadcast address is 10.1.255.
PAGE 779
TenGigabitEthernet 1/1/2/3 down down unassigned NO Manual administratively show ip management-route View the IP addresses assigned to the Management interface. Syntax Parameters show ip management-route [all | connected | summary | static] all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
PAGE 780
show ipv6 management-route Display the IPv6 static routes configured for the management interface. Syntax show ipv6 management-route [all | connected | summary | static] Parameters all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
PAGE 781
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 782
show ip route View information, including how they were learned, about the IP routes on the switch. Syntax show ip route [vrf vrf-name] hostname | ip-address [mask] [longer-prefixes] | list prefix-list | protocol [process-id | routing-tag] | all | connected | static | summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the VRF name to list the routes in the route table of a specific VRF.
PAGE 783
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 784
Example DellEMC# show ip route all Codes:C- connected, S - static, R - RIP B- BGP, IN - internal BGP, EX - external BGP, LO - Locally Originated O- OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1 N2- OSPF NSSA external type 2, E1 - OSPF external type 1 E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1 L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default >- non-active route + - summary route Gateway of last resort is not set Destination Gateway Dist/Metric Last ----------- -------
PAGE 785
----------S 1.1.1.0/24 00:00:01 C 4.4.4.0/24 00:01:32 C 6.6.6.0/24 00:01:25 4.4.4.2, via Te 1/1/4/1 , weight 100 6.6.6.2, via Te 1/1/6/1, Direct, Te 1/1/4/1 Direct, Te 1/1/6/1 1/0 weight 200 0/0 0/0 DellEMC# show ip route 1.1.1.0/24 Routing entry for 1.1.1.0/24 Known via "static", distance 1, metric 0 Last update 00:05:01 ago Routing Descriptor Blocks: * 4.4.4.2, via TenGigabitEthernet 1/1/4/1 weight 100 * 6.6.6.
PAGE 786
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 787
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 788
Related Commands ● show ip route — display information about the routes found in the switch. show ip traffic View IP, ICMP, UDP, TCP and ARP traffic statistics. Syntax show ip traffic [all | cp | rp1 | rp2] NOTE: These options are supported only on the E-Series. Parameters all (OPTIONAL) Enter the keyword all to view statistics from all processors. If you do not enter a keyword, you also view all statistics from all processors.
PAGE 789
Keyword Definition unknown protocol... No receiver for these packets. Counts packets whose protocol type field is not recognized by Dell EMC Networking OS. not a gateway... Packets can not be routed; the host/network is unreachable. security failures...
PAGE 790
0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench 0 parameter, 0 timestamp, 0 info request, 0 other Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply 0 mask requests, 0 mask replies, 0 quench, 0 timestamp 0 info reply, 0 time exceeded, 0 parameter problem UDP statistics: Rcvd: 0 total, 0 checksum errors, 0 no port 0 short packets, 0 bad length, 0 no port broadcasts, 0 socket full Sent: 0 total, 0 forwarded broadcasts TCP statistics: Rcvd: 23829 total, 0 checksum errors, 0 no port Sent: 16
PAGE 791
Example Field Description Rcvd: Displays the number and types of TCP packets received by the switch. ● Total = total packets received ● no port = number of packets received with no designated port 0 checksum error... Displays the number of packets received with the following: ● checksum errors ● bad offset to data ● too short 329 packets... Displays the number of packets and bytes received in sequence. 17 dup... Displays the number of duplicate packets and bytes received. 0 partially...
PAGE 792
0 packets ( 0 bytes) with data after window 0 packets after close 0 window probe packets, 41 window update packets 41 dup ack packets, 0 ack packets with unsend data 10184 ack packets (12439508 bytes) Sent: 12007 Total, 0 urgent packets 25 control packets (including 24 retransmitted) 11603 data packets (12439677 bytes) 24 data packets (7638 bytes) retransmitted 355 ack only packets (41 delayed) 0 window probe packets, 0 window update packets 7 Connections initiated, 8 connections accepted, 15 connections es
PAGE 793
23 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 794
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 795
message is generated. Valid range is 1 to 100. When warn-threshold is used, once the limit is reached, additional routes will not be allowed into the RTM ( route table manager ) itself. warning-only Defaults When the warning-only option is used, a syslog message will be thrown when maximum number of dynamic IPv6 routes reaches the limit. Additional dynamic IPv6 routes will still be allowed. No limit is set on the maximum number of dynamic IPv6 routes for a VRF.
PAGE 796
Usage Information Example You can use this command to view the number of supported extended prefix entries in LPM configured. The output also displays the current applied value and the new value that is applicable after the reboot of the device. DellEMC# show cam-ipv6 extended-prefix Cam-Ipv6-LPM Extended Prefix -------------------------------Current Settings cam-ipv6-max-/65-to-/128-Prefix : 2048 DellEMC(conf)# ipv6 unicast-host-route Enable programming of IPv6 /128 route prefixes in L3 host table.
PAGE 797
Version Description 9.11.0.1 Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S4810, S4820, S5000, S6000, S6010–ON, S6000–ON, S6100–ON, Z9100–ON, C9010, Z9500, MXL, and FN IOM. ipv6 nd dns-server Configures Recursive DNS Server (RDNSS) addresses to be distributed via IPv6 router advertisements to an IPv6 device.
PAGE 798
To restore to default, use the no ipv6 nd reachable-time command. Parameters Default reachable-time Enter the reachable time in milliseconds. The value is from 0 to 3600000. The default value is 0. Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON.
PAGE 799
Configure the IPv6 route using a next-hop IPv6 address in order for the ping command to detect the destination address. ipv6-address (OPTIONAL) Enter the forwarding router IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. distance (OPTIONAL) Enter a number as the metric distance assigned to the route. The range is from 1 to 255. name description (OPTIONAL) Enter the keyword name and the description for the IPv6 static route configuration.
PAGE 800
Dell EMC Networking OS withdraws the route. The route is re-installed, by Dell EMC Networking OS, when the recursive resolution is satisfied. After an IPv6 static route interface is created, if an IP address is not assigned to a peer interface, the peer must be manually pinged to resolve the neighbor information. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect.
PAGE 801
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 802
Example (SSeries) Field Description Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured.
PAGE 803
24 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 804
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. Example Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs.
PAGE 805
Example (Manual Profiles) DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) L2Acl : 2 Ipv4Acl : 2 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 3 -- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 806
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.
PAGE 807
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 808
Defaults cpu-qos Enter the keyword cpu-qos to assign this ACL to control plane traffic only (CoPP). permit Enter the keyword permit to configure a filter to forward packets meeting this condition. deny Enter the keyword deny to configure a filter to drop packets meeting this condition. ospfv3 Specify that this ACL is for OSPFv3 control plane traffic All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped.
PAGE 809
Parameters Defaults access-list-name Enter the name of a configured access list, up to 140 characters. in | out Enter either the keyword in or out to apply the IPv6 ACL to incoming traffic (ingress) or outgoing traffic (egress). implicit-permit (OPTIONAL) Enter the keywords implicit-permit to change the default action of the IPv6 ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the IPv6 ACL, the traffic is permitted instead of dropped).
PAGE 810
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 811
cam-acl Allocate space for IPv6 ACLs. Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: ● L3 ACL (ipv4acl): 2 ● L2 ACL(l2acl): 2 ● IPv6 L3 ACL (ipv6acl): 0 ● L3 QoS (ipv4qos): 2 ● L2 QoS (l2qos): 2 l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 812
25 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 813
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 814
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
PAGE 815
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1.
PAGE 816
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain. ● isis password — configure an authentication password for an interface.
PAGE 817
tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 818
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command.
PAGE 819
debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies. Syntax debug isis [vrf vrf-name] adj-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name]adj-packets [interface] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details.
PAGE 820
debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information. Syntax debug isis [vrf vrf-name] local-updates [interface] To turn off debugging, use the no debug isis [vrf vrf—name] updates [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF.
PAGE 821
debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. Syntax debug isis [vrf vrf-name] snp-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name] snp-packets [interface] command.
PAGE 822
debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. Syntax debug isis [vrf vrf-name] spf-triggers To turn off debugging, use the no debug isis [vrf vrf-name] spf-triggers command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging information on IS-IS corresponding to that VRF. This information contains SPF trigger detail tied to the VRF that you specify.
PAGE 823
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information.
PAGE 824
Defaults Not configured. Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 825
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 826
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. The administrative distance indicates the trust value of incoming packets. A low administrative distance indicates a high trust rate. A high value indicates a lower trust rate.
PAGE 827
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced.
PAGE 828
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. Usage Information You can assign a name to a routing process so a prefix list IS applied to only the routes derived from the specified routing process.
PAGE 829
Usage Information When you execute this command, IS-IS does not download the route to the routing table if the same route was redistributed into IS-IS routing protocol on the same router. domain-password Set the authentication password for a routing domain. Syntax domain-password [hmac-md5 | encryption-type] password To disable the password, use the no domain-password command. Parameters Defaults hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5.
PAGE 830
Parameters Defaults ietf Enter ietf to enable graceful restart on the IS-IS router. Graceful restart disabled. Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 831
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 832
Related Commands Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. ● graceful-restart t3 — configure the overall wait time before graceful restart completes. graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated.
PAGE 833
graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize. Syntax graceful-restart t2 {level-1 | level-2} seconds To return to the default, use the no graceful-restart t2 command. Parameters Defaults level-1, level-2 Enter the keywords level-1 or level-2 to identify the database instance type to which the wait interval applies. seconds Enter the gracefule-restart t2 time in seconds.
PAGE 834
Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 835
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 836
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To build name-to-systemID mapping tables through the protocol, use this command. All show commands that display systems also display the hostname. Related Commands ● clns host — define a name-to-NSAP mapping. ignore-lsp-errors Ignore LSPs with bad checksums instead of purging those LSPs. Syntax ignore-lsp-errors To return to the default values, use the no ignore-lsp-errors command.
PAGE 837
Parameters Defaults tag (OPTIONAL) The tag you specify identifies a specific area routing process. If you do not specify a tag, a null tag is assigned. No processes are configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 838
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 839
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 840
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The default values of this command are typically satisfactory transmission times for a specific interface on a designated intermediate system.
PAGE 841
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Hello packets are held for a length of three times the value of the hello interval. To conserve bandwidth and CPU usage, use a high hello interval seconds. Use a low hello interval seconds for faster convergence (but uses more bandwidth and CPU resources).
PAGE 842
Related Commands ● isis hello-interval — specify the length of time between hello packets. isis hello padding Turn ON or OFF padding of hello PDUs from INTERFACE mode. Syntax isis hello padding To return to the default, use the no isis hello padding command. Defaults Padding of hello PDUs is enabled (ON). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 843
level-2 Defaults (OPTIONAL) Enter the keywords level-2 to configure the SPF calculation for Level 2 (inter-area) routing. default-metric = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 844
level-2 Defaults (OPTIONAL) Enter the keywords level-2 to configure the SPF calculation for Level 2 (inter-area) routing. default-metric = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 845
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. isis password Configure an authentication password for an interface. Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [password] [level-1 | level-2] command.
PAGE 846
You can assign different passwords for different routing levels by using the keywords level-1 and level-2. The no form of this command disables the password for Level 1 or Level 2 routing, using the respective keywords level-1 or level-2. This password provides limited security as it is processed as plain text. isis priority Set the priority of the designated router you select.
PAGE 847
is-type Configure IS-IS operating level for a router. Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters Defaults level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. level-1-2 Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific.
PAGE 848
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 849
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.
PAGE 850
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The link MTU and the LSP MTU size must be the same.
PAGE 851
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The refresh interval determines the rate at which route topology information is transmitted preventing the information from becoming obsolete. The refresh interval must be less than the LSP lifetime specified with the max-lsp-lifetime command.
PAGE 852
max-lsp-lifetime Set the maximum time that link-state packets (LSPs) exist without being refreshed. Syntax max-lsp-lifetime seconds To restore the default time, use the no max-lsp-lifetime command. Parameters Defaults seconds The maximum lifetime of LSP in seconds. This value must be greater than the lsp-refresh-interval command. The higher the value the longer the LSPs are kept. The range is from 1 to 65535. The default is 1200.
PAGE 853
Defaults 4 Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 854
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 855
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Introduced. net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start.
PAGE 856
passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 857
redistribute Redistribute routes from one routing domain to another routing domain. Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map mapname] To end redistribution or disable any of the specified keywords, use the no redistribute {static | connected | rip} [metric metric-value] [metric-type {external | internal}] [level-1 | level-1-2 | level-2] [route-map map-name] command.
PAGE 858
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. To redistribute a default route (0.0.0.0/0), configure the default-information originate command. Changing or disabling a keyword in this command does not affect the state of the other command keywords. When an LSP with an internal metric is received, the Dell EMC Networking OS considers the route cost while considering the advertised cost to reach the destination.
PAGE 859
Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 860
metric metric- value (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0. metric-type {external | internal} (OPTIONAL) The external link type associated with the default route advertised into a routing domain. The two options are: ● external ● internal level-1 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 1 routes.
PAGE 861
router isis Allows you to enable the IS-IS routing protocol and to specify an IP IS-IS process. Syntax router isis [vrf vrf-name] [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters Defaults vrf vrf-name Enter the keyword vrf followed by the name of the VRF to enable the IS-IS routing protocol and to specify an IP IS-IS process on that VRF. tag (OPTIONAL) This is a unique name for a routing process. A null tag is assumed if the tag option is not specified.
PAGE 862
To return to the default values, use the no set-overload-bit command. Defaults Not set. Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 863
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. Example (Router- The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode.
PAGE 864
local (OPTIONAL) Displays local link-state database information. detail (OPTIONAL) Displays the detailed link-state database information of each LSP when specified. If not specified, a summary displays. summary (OPTIONAL) Displays the summary of link-state database information when specified. lspid (OPTIONAL) Display only the specified LSP. system-id (OPTIONAL) Displays the link-state database for system-id.
PAGE 865
Example Field Description LSP Checksum This is the checksum of the entire LSP packet. LSP Holdtime This value is the amount of time, in seconds, that the LSP remains valid. A zero holdtime indicates that this is a purged LSP and is being removed from the link state database. A value between brackets indicates the duration that the purged LSP stays in the database before being removed. ATT This value represents the Attach bit.
PAGE 866
Metric: 10 IPv6 2511::/64 Metric: 20 IPv6 1033::/64 Hostname: ISIS DellEMC# show isis database detail IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum ATT/P/OL FTOS.00-00 * 0x00000009 0x79D8 NLPID: 0xCC Area Address: 49.0000.0001 LSP Holdtime 941 1/0/0 show isis graceful-restart detail Display detailed IS-IS graceful restart related settings.
PAGE 867
T2 Timeout Value : 30 (level-1), 30 (level-2) T1 Timeout Value : 5, retry count: 1 Adjacency wait time : 30 Operational Timer Value ====================== Current Mode/State : T3 Time left : T2 Time left : Restart ACK rcv count : Restart Req rcv count : Suppress Adj rcv count : Restart CSNP rcv count : Database Sync count : Normal/RUNNING 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 (level-2) (level-2) (level-2) (level-2) (level-2) (level-2) show isis hostna
PAGE 868
show isis interface Display detailed IS-IS interface status and configuration information. Syntax show isis [vrf vrf-name] interface [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS interface status information corresponding to that VRF.
PAGE 869
Interface Index 37847070, Local circuit ID 1 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.01 Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10 Number of active level-1 adjacencies: 1 Level-2 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 870
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 871
show isis protocol Display IS-IS routing information. Syntax Parameters show isis [vrf vrf-name] protocol vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS routing information corresponding to that VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 872
show isis traffic This command allows you to display IS-IS traffic interface information. Syntax show isis [vrf vrf-name] traffic [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS traffic interface information corresponding to that VRF.
PAGE 873
Example Item Description PTP Hellos (sent/rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs. Level-1/Level-2 LSPs flooded (sent/rcvd) Displays the number of flooded LSPs sent and received. Level-1/Level-2 LSPs CSNPs (sent/ rcvd) Displays the number of CSNP LSPs sent and received. Level-1/Level-2 LSPs PSNPs (sent/ rcvd) Displays the number of PSNP LPSs sent and received.
PAGE 874
Parameters level-l (OPTIONAL) Enter the keyword level-1 to apply the configuration to Level-1 SPF calculations. level-2 (OPTIONAL) Enter the keyword level-2 to apply the configuration to Level-2 SPF calculations. interval seconds Enter the maximum number of seconds between SPF calculations. The range is from 0 to 120 seconds. The default is 10 seconds. initial_wait_inter (OPTIONAL) Enter the initial wait time, in seconds, before running the first SPF val seconds calculations.
PAGE 875
26 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 876
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters Defaults time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 877
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 878
Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 879
ip-address (Optional) Defaults Enter the ip-address that the iSCSI monitors. The ip-address specifies the IP address of the iSCSI target. 860, 3260 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 880
-----------------------------------------------iSCSI Targets and TCP Ports: -----------------------------------------------TCP Port Target IP Address 3260 860 Related Commands ● show iscsi session — display information about active iSCSI sessions on the switch. ● show iscsi session detailed — display detailed information about active iSCSI sessions on the switch. ● show run iscsi — show run iscsi. show iscsi session Display information about active iSCSI sessions on the switch.
PAGE 881
show iscsi session detailed Display detailed information on active iSCSI sessions on the switch. Syntax Parameters show iscsi session detailed [session isid] isid Enter the session’s iSCSi ID to display detailed information about the specified iSCSi session. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 882
Command History Related Commands 882 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 883
27 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 884
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 885
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 886
Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command applies to dynamic port-channel interfaces only. When applied on a static port-channel, this command has no effect. Related Commands ● show lacp — display the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority.
PAGE 887
lacp system-priority Configure the LACP system priority. Syntax Parameters Defaults lacp system-priority priority-value priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 888
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced on the E-Series.
PAGE 889
Example (Port-ChannelNumber) Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# show lacp 1 Port-channel 1 admin up, oper up, mode lacp Actor System ID:Priority 32768, Address 0001.e800.a12b Partner System ID:Priority 32768, Address 0001.e801.
PAGE 890
28 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 891
Related Commands Version Description 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. ● mac learning-limit — set the MAC address learning limits for a selected interface. ● show mac-address-table aging-time — display the MAC aging time.
PAGE 892
Related Commands ● mac learning-limit — set the MAC address learning limits for a selected interface. ● show mac-address-table aging-time — display the MAC aging time. mac-address-table static Associate specific MAC or hardware addresses to an interface and VLANs. Syntax mac-address-table static mac-address {multicast vlan vlan-id output—range interface}{output interface vlan vlan-id} To remove a MAC address, use the no mac-address-table static mac-address output interface vlan vlan-id command.
PAGE 893
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for output range parameter for S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 894
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
PAGE 895
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Deprecated the no-station-move command (replaced by the mac-learninglimit mac-address-sticky command). 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 896
Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 897
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
PAGE 898
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 899
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. mac port-security Enable or disable the port security feature globally in the system. Syntax mac port-security To disable the port security, use the no mac port-security command. Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 900
● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 901
Example Usage Information Example (Count) Related Commands Column Heading Description VlanId Displays the VLAN ID number. Mac Address Displays the MAC address in nn:nn:nn:nn:nn:nn format. Type Lists whether the MAC address was manually configured (Static), learned dynamically (Dynamic), or associated with a specific port (Sticky). Interface Displays the interface type and slot/port[/subport] information.
PAGE 902
Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display the MAC address assigned to the VLAN. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 903
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information.
PAGE 904
default vlan-id Specify a VLAN as the Default VLAN. Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters Defaults vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific.
PAGE 905
Parameters Defaults description Enter a text string description to identify the VLAN (80 characters maximum). none Command Modes INTERFACE VLAN Command History Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 906
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced The no default vlan disable command is not listed in the running-configuration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters Defaults vlan-name Enter up to 32 characters as the name of the VLAN. Not configured.
PAGE 907
show config Display the current configuration of the selected VLAN. Syntax show config Command Modes INTERFACE VLAN Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 908
id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094. Only information on the VLAN specified is displayed. name vlan-name (OPTIONAL) Enter the keyword name then the name configured for the VLAN. Only information on the VLAN named is displayed. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 908 Layer 2 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 909
Column Heading Description ● ● ● ● ● ● ● ● ● Ports Example x (not capitalized x) for Dot1x untagged X (capitalized X) for Dot1x tagged o (not capitalized o) for OpenFlow untagged O (capitalized O) for OpenFlow tagged H for VSN tagged i (not capitalized i) for Internal untagged I (capitalized I) for Internal tagged v (not capitalized v) for VLT untagged V (capitalized V) for VLT tagged Displays the type, slot, and port information.
PAGE 910
40 Active M Te 1/1/4/1 DellEMC# show vlan id 41 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 41 Status Description Q Ports Active T Te 1/1/4/1 DellEMC# show vlan id 42 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 42 DellEMC# Example (Brief) Example (Name) Status Description Q Ports Active U Te 1/1/4/1 DellEMC# show
PAGE 911
Parameters Defaults interface Enter the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 912
track ip Track the Layer 3 operational state of a Layer 3 VLAN, using a subset of the VLAN member interfaces. Syntax track ip interface To remove the tracking feature from the VLAN, use the no track ip interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 913
If the track ip command is not configured, the VLAN's Layer 3 operational state depends on all the members of the VLAN. The Layer 2 state of the VLAN, and the Layer 2 traffic, is not affected by the track ip command configuration. Related Commands ● interface vlan — configure a VLAN. ● tagged — specify which interfaces in a VLAN are tagged. untagged Add a Layer 2 interface to a VLAN as an untagged interface.
PAGE 914
Usage Information Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Untagged interfaces can only belong to one VLAN. In the Default VLAN, you cannot use the no untagged interface command. To remove an untagged interface from all VLANs, including the Default VLAN, enter INTERFACE mode and use the no switchport command. ● interface vlan — configure a VLAN.
PAGE 915
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 916
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
PAGE 917
Usage Information FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. Related Commands ● fefd reset — clear an interface in Err-disabled state. It doesn’t work until the interface is in errdisabled state. ● fefd mode — change FEFD mode on an interface. fefd interval Set an interval between control packets. Syntax fefd interval seconds To return to the default value, use the no fefd interval command.
PAGE 918
Parameters Defaults normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol. aggressive (OPTIONAL) Enter the keyword aggressive to change the link state to “errordisabled” when a far-end failure the software detects on that interface.
PAGE 919
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 920
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. ● fefd-global — enable FEFD globally on the system. fefd-global Enable FEFD globally on the system.
PAGE 921
Version Description 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Usage Information Related Commands If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. ● fefd — enable far-end failure detection. ● fefd-global interval — configure an interval between FEFD control packets. ● show fefd — display the FEFD command output.
PAGE 922
Version Description Legacy E-Series command. Usage Information The following describes the show fefd command shown in the following example. Field Description Interface Displays the interfaces type and number. Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets.
PAGE 923
29 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 924
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
PAGE 925
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor.
PAGE 926
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 927
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 928
Defaults packet Enter the keyword packet to display information regarding packets coming in or going out. brief Enter the keyword brief to display brief packet information. detail Enter the keyword detail to display detailed packet information. tx Enter the keyword tx to display transmit-only packet information. rx Enter the keyword rx to display receive-only packet information. both Enter the keyword both to display both receive and transmit packet information.
PAGE 929
disable Enable or disable LLDP. Syntax disable To enable LLDP, use the no disable command. Defaults Enabled — no disable. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 930
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 931
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. ● protocol lldp (Configuration) — enable LLDP globally. ● show lldp neighbors — display the LLDP neighbors.
PAGE 932
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch. Syntax protocol lldp To disable LLDP globally on the chassis, use the no protocol lldp command. Defaults Enabled. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 933
Command Modes INTERFACE (conf-if-interface-lldp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 934
Defaults None Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13.0.0 Enhanced to display organizational specific unrecognized LLDP TLVs. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 935
58, 4) 68, 4) 78, 4) 88, 4) 98, 4) (108, 4) (118, 4) ( 59, 4) ( 60, 4) ( 61, 4) ( 62, 4) ( 63, 4) ( 64, 4) ( 65, 4) ( 66, 4) ( 67, 4) ( ( 69, 4) ( 70, 4) ( 71, 4) ( 72, 4) ( 73, 4) ( 74, 4) ( 75, 4) ( 76, 4) ( 77, 4) ( ( 79, 4) ( 80, 4) ( 81, 4) ( 82, 4) ( 83, 4) ( 84, 4) ( 85, 4) ( 86, 4) ( 87, 4) ( ( 89, 4) ( 90, 4) ( 91, 4) ( 92, 4) ( 93, 4) ( 94, 4) ( 95, 4) ( 96, 4) ( 97, 4) ( ( 99, 4) (100, 4) (101, 4) (102, 4) (103, 4) (104, 4) (105, 4) (10
PAGE 936
Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: hundredGigE 1/1/2 Locally assigned remote Neighbor Index: 3 Remote TTL: 300 Information valid for next 199 seconds Time since last information change of this neighbor: 00:01:41 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),120, 4) ((00-01-66),119, ((00-01-66),118, 4) -----------------
PAGE 937
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 938
Usage Information SNMP notification for the changes in the lldp remote entry table is throttled by 5 seconds (default), or the configured time set using this command. If more than one notification message is generated within the configured time, only the first one will be sent and the remaining messages are suppressed. LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands.
PAGE 939
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● protocol lldp (Configuration) — enable LLDP globally.
PAGE 940
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 941
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. Usage Information ● ECS — Emergency call service such as defined by TIA or the national emergency numbering association (NENA) ● ELIN — Emergency location identification number, a valid North America Numbering Plan format telephone number supplied for ECS purposes.
PAGE 942
advertise med softphone-voice To advertise softphone to enable IP telephony on a computer so that the computer can be used as a phone, configure the system. Syntax advertise med softphone-voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med softphone-voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 943
advertise med streaming-video To advertise streaming video services for broadcast or multicast-based video, configure the system. This command does not include video applications that rely on TCP buffering. Syntax advertise med streaming-video {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med streaming-video {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID.
PAGE 944
advertise med video-conferencing To advertise dedicated video conferencing and other similar appliances that support real-time interactive video, configure the system. Syntax advertise med video-conferencing {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med video-conferencing {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 945
advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system. Syntax advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority.
PAGE 946
advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system. Syntax advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority. The range is from 0 to 7.
PAGE 947
To return to the default, use the no advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority. The range is from 0 to 7. DSCP_value Enter the DSCP value. The range is from 0 to 63. priority-tagged Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. number Defaults Unconfigured.
PAGE 948
30 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 949
Version Description 9.3(0.0) Added support for association of an IP address with multicast MAC address on the S4810, S4820T, S6000, and Z9000 platforms. Usage Information For multicast mode of NLB, to associate an IP address with a multicast MAC address in the switch, use address resolution protocol (ARP) by entering the arp ip-address multicast-mac-address command in Global configuration mode.
PAGE 950
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Management interface, enter the keyword managementethernet followed by slot/port numbers. ● For a Port Channel interface, enter the keywords port-channel followed by a number. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 951
Usage Information By default this command is disabled. There might be some ARP table entries which are resolved through ARP packets which had Ethernet MAC SA different from MAC information inside the ARP packet. This unicast data traffic flooding occurs only for those packets which use these ARP entries.
PAGE 952
31 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the platform.
PAGE 953
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 954
Version Description 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax clear ip msdp statistic peer peer-address Parameters Defaults peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer.
PAGE 955
ip msdp cache-rejected-sa Enable an MSDP cache for the rejected source-active entries. Syntax ip msdp cache-rejected-sa {number} To clear the MSDP rejected source-active entries, use the no ip msdp cache-rejected-sa {number} command then the ip msdp cache-rejected-sa {number} command. Parameters Defaults number Enter the number of rejected SA entries to cache. The range is from 0 to 32766. None Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 956
list name Defaults Enter the keywords list name and specify a standard access list that contains the RP address that should be treated as the default peer. If no access list is specified, then all SAs from the peer are accepted. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 957
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip msdp mesh-group To be a member of a mesh group, configure a peer.
PAGE 958
Usage Information Version Description 6.2.1.1 Introduced An MSDP mesh group is a mechanism for reducing SA flooding, typically in an intra-domain setting. When some subset of a domain’s MSDP speakers are fully meshed, they can be configured into a mesh-group. If member X of a mesh-group receives a SA message from an MSDP peer that is also a member of the mesh-group, member X accepts the SA message and forwards it to all of its peers that are not part of the mesh-group.
PAGE 959
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 6.2.1.1 Introduced ip msdp peer Configure an MSDP peer. Syntax ip msdp peer peer address [connect-source] [description] [sa-limit number] To remove the MSDP peer, use the no ip msdp peer peer address [connect-source interface] [description name] [sa-limit number] command.
PAGE 960
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.5.1.
PAGE 961
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced Modifications to the ACL do not have an immediate effect on the sa-cache.
PAGE 962
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the E-Series. ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters Defaults number Enter the maximum number of SA entries in SA-cache. The range is from 1 to 500000.
PAGE 963
● show ip msdp — display the MSDP information. ip msdp shutdown Administratively shut down a configured MSDP peer. Syntax Parameters Defaults ip msdp shutdown {peer address} peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 964
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 965
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced DellEMC# show ip msdp peer 100.1.1.1 Peer Addr: 100.1.1.1 Local Addr: 100.1.1.
PAGE 966
Example 966 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 7.4.1.0 Introduced.
PAGE 967
32 Multicast Listener Discovery Protocol The Multicast Listener Discovery (MLD) protocol is used by IPv6 routers to discover multicast listeners on a directly attached link. Similar to the Internet Group Management Protocol (IGMP), which handles multicast group memberships in IPv4 networks, MLD is used for multicast management on IPv6 networks.
PAGE 968
Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. debug ipv6 mld Enable debugging on IPv6 MLD packets. Syntax debug ipv6 mld [vrf vrf-name] {group-address | interface} To turn off debugging, use the no debug ipv6 mld {group-address | interface} command. Parameters Defaults vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF.
PAGE 969
Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld last-member-query-interval Change the MAX Response Time inserted into the Group-Specific Queries sent in response to a Leave Group messages. This interval is also the interval between Group-Specific Query messages.
PAGE 970
Parameters Defaults seconds Enter the interval in seconds. The range is from 1 to 25. 10 seconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld version Configure the MLD version on the system.
PAGE 971
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port/subport information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the slot/port/subport information. ● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094.
PAGE 972
Example Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 973
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. debug ipv6 mld snooping Enable debugging on IPv6 MLD snooping packets.
PAGE 974
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping enable Enable MLD snooping on the switch globally. Syntax ipv6 mld snooping enable To disable MLD snooping, use the no ipv6 mld snooping enable command.
PAGE 975
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 976
interface interface detail Defaults Enter the following keywords and slot/port or number information: ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port/subport information.
PAGE 977
Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Updated the output to show both MLD versions 1 and 2. 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 978
33 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 979
Optionally, enter an in or out parameter with the optional interface: ● For Receive, enter the keyword in. ● For Transmit, enter the keyword out. events (OPTIONAL) Enter the keyword events to debug MSTP events. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 980
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 981
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● max-age — change the wait time before MSTP refreshes protocol configuration information.
PAGE 982
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● forward-delay — amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. ● max-age — change the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB.
PAGE 983
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
PAGE 984
name The name you assign to the multiple spanning tree region. Syntax name region-name To remove the region name, use the no name command. Parameters Defaults region-name Enter the MST region name. The range is 32 character limit. No default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 985
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.1) Introduced on MXL, FN IOM, S6000, S3100, S4810, S4820T, S3048–ON, S4048– ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, S5048F-ON, C9010, and Z9100–ON, This command is used to keep the port-channel path cost constant regardless of the operational status of the port-channel member ports.
PAGE 986
Usage Information MSTP is not enabled when you enter MULTIPLE SPANNING TREE mode. To enable MSTP globally on the switch, enter the no disable command while in MULTIPLE SPANNING TREE mode. For more information about the multiple spanning tree protocol, refer to the Dell EMC Networking OS Configuration Guide. Example Related Commands DellEMC(conf)# protocol spanning-tree mstp DellEMC(config-mstp)#no disable ● disable — disable multiple spanning tree.
PAGE 987
show config View the current configuration for the mode. Only non-default values are shown. Syntax show config Command Modes MULTIPLE SPANNING TREE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 988
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 989
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
PAGE 990
Example (EDS and LBK) The bold line shows the loopback BPDU inconsistency (LBK_INC). DellEMC# show spanning-tree msti 0 brief MSTI 0 VLANs mapped 1-4094 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15, max hops 20 Bridge ID Priority 32768, Address 0001.e801.
PAGE 991
spanning-tree Enable the multiple spanning tree protocol on the interface. Syntax spanning-tree To disable the multiple spanning tree protocol on the interface, use the no spanning-tree command. Parameters Defaults spanning-tree Enter the keywords spanning-tree to enable the MSTP on the interface. Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 992
● ● ● ● ● ● ● priority priority Defaults 10-Gigabit Ethernet interface = 2000 Port Channel interface with one 100 Mb/s Ethernet = 200000 Port Channel interface with one 1 Gigabit Ethernet = 20000 Port Channel interface with one 10 Gigabit Ethernet = 2000 Port Channel with two 1 Gigabit Ethernet = 18000 Port Channel with two 10 Gigabit Ethernet = 1800 Port Channel with two 100 Mbps Ethernet = 180000 Enter keyword priority then a value in increments of 16 as the priority. The range is from 0 to 240.
PAGE 993
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 994
34 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 995
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 996
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 997
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile.
PAGE 998
Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
PAGE 999
-4 103.103.103.3 --> Source -----------------------------------------------------------------The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic. The mtrace command traverses the reverse path to the source from the destination.
PAGE 1000
-----------0 Te 1/3/3/1, 0 Te 1/3/3/1, 0 Te 1/3/3/1, 224.1.1.1 0.0.0.0 1000 1 Te 1/3/1/1, 224.1.1.2 0.0.0.0 1000 1 Te 1/3/1/1, 224.1.1.1 165.13.34.5 2000 2 Te 1/3/5/1, show ip mroute View the multicast routing table.
PAGE 1001
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 1002
Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 1003
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources.
PAGE 1004
ipv6 multicast-routing Enables IPv6 multicast forwarding. Syntax ipv6 multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable IP multicast forwarding on that VRF. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1005
9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1006
L2 Ports : L3 Ports : Te 1/3/3/1 show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1007
35 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1008
NOTE: If you do not specify this option, the neighbors in the default VRF are cleared. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format to remove a specific IPv6 neighbor. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1009
● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1010
Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1011
● ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode. ipv6 nd ra–guard attach–policy Apply the IPv6 RA guard to a specific interface. Syntax Parameters ipv6 nd ra-guard attach—policy policy-name [vlan [vlan 1, vlan 2, vlan 3.....]] policy policy- name vlan [vlan 1, vlan 2, vlan 3........] Defaults Enter the keyword policy then the policy name. The policy-name allows a maximum of 140 characters. Enter the keyword vlan then the VLAN range.
PAGE 1012
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1013
ipv6 neighbor Configure a static entry in the IPv6 neighbor discovery. Syntax ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} {hardware_address} To remove a static IPv6 entry from the IPv6 neighbor discovery, use the no ipv6 neighbor [vrf vrf-name] {ipv6-address} {interface interface} command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
PAGE 1014
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. Neighbor Discovery Protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4. It defines mechanisms for solving problems, such as: ● Router discovery: Hosts can locate routers residing on a link.
PAGE 1015
Related Commands ● ipv6 nd ra-guard enable — configure the RA guard related commands. ● ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. match ra Enable verifying either of the configured source IPv6 address or prefix address or the source MAC address in the inspected messages. If this command is not configured, the verification process is bypassed.
PAGE 1016
To reset the access list, use the no match ra{ipv6-access-list | ipv6-prefix-list | mac-access-list}command. Parameters ipv6–access-list name ipv6–prefix-list Defaults Enter the keywords ipv6–access-list then the access-list name. The accesslist name allows a maximum of 140 characters. name Enter the keywords ipv6–prefix-list then the prefix-list name. The prefix-list name allows a maximum of 140 characters.
PAGE 1017
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches.
PAGE 1018
Related Commands ● ipv6 nd ra-guard enable — configure the RA guard related commands. ● ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. reachable–time Enable the verification of the configured reachability time in the received RA packets. Syntax reachable—time value To reset the advertised reachability time, use the no reachable-timevalue command.
PAGE 1019
Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1020
router–preference maximum Enable the verification of the advertised default router preference (DRP) value. The preference value is lower than or equal to the specified limit. If this command is not configured, the verification process is bypassed. Syntax router-preference maximum {high | low | medium} To reset the default router preference value, use the no router-preference maximum {high | low | medium} command. Parameters Defaults high Enter the keyword high to set the DRP value as high.
PAGE 1021
Example Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1022
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Introduced on the S6000–ON, and Z9000 switches.
PAGE 1023
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1024
trusted–port Allow bypassing the configured RA guard validation and forwards the RA packets received on the interface, which has the trusted port policy attached. Syntax trusted-port To reset the policy applied to the trusted port, use the no trusted-port command. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1025
36 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1026
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Example delay Configure the time delay used before communicating a change in the status of a tracked object to clients. Syntax delay {[up seconds] [down seconds]} To return to the default setting, use the no delay command.
PAGE 1027
● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. ● track ip route reachability – configure object tracking on the reachability of an IPv4 route. description Enter a description of a tracked object. Syntax description {text} To remove the description, use the no description {text} command. Parameters Defaults text Enter a description to identify a tracked object (80 characters maximum).
PAGE 1028
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# show running-config track track 1 ip route 23.0.0.
PAGE 1029
interface (OPTIONAL) Display information on all tracked interfaces (Layer 2 and IPv4 Layer 3). ip route (OPTIONAL) Display information on all tracked IPv4 routes. resolution (OPTIONAL) Display information on the configured resolution values used to scale protocol-specific route metrics. The range is 0 to 255. brief (OPTIONAL) Display a single line summary of the tracking information for a specified object, object type, or all tracked objects.
PAGE 1030
Track 2 IPv6 route 2040::/64 metric threshold Metric threshold is Up (STATIC/0/0) 5 changes, last change 00:02:16 Metric threshold down 255 up 254 First-hop interface is TenGigabitEthernet 1/1/2/1 Tracked by: VRRP TenGigabitEthernet 1/1/3/4 IPv6 VRID 1 Track 3 IPv6 route 2050::/64 reachability Reachability is Up (STATIC) 5 changes, last change 00:02:16 First-hop interface is TenGigabitEthernet 1/1/2/1 Tracked by: VRRP TenGigabitEthernet 1/1/3/4 IPv6 VRID 1 Usage Information Example (Brief) Related Command
PAGE 1031
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1032
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 1033
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1034
vrf vrf-name Defaults (Optional) E-Series only: You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1035
To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefix-len Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32. vrf vrf-name (Optional) E-Series only: You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs.
PAGE 1036
Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1037
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to configure the protocol-specific resolution value that converts the actual metric of an IPv4 route in the routing table to a scaled metric in the range 0 to 255.
PAGE 1038
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. The following describes the show track ipv6 route command shown in the Example below.
PAGE 1039
Example (Brief) Ouput Description State Up or Down state of the tracked object. Last Change Time since the last change in the state of the tracked object. DellEMC# show track ipv6 route brief ResId Resource Parameter State LastChange 2 IPv6 route metric threshold 2040::/64 Up 00:02:36 3 IPv6 route reachability 2050::/64 Up 00:02:36 Related Commands ● show running-config track – display configuration information about tracked objects.
PAGE 1040
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced.
PAGE 1041
Usage Information Use this command to create an object that tracks the UP and/or DOWN threshold of an IPv6 route metric. In order for a route’s metric to be tracked, the route must appear as an entry in the routing table. A tracked IPv6 route is considered to match an entry in the routing table only if the exact IPv6 address and prefix length match a table entry. For example, when configured as a tracked route, 3333:100:200:300:400::/80 does not match routing table entry 3333:100:200:300::/64.
PAGE 1042
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv6 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked route is considered to match an entry in the routing table only if the exact IPv6 address and prefix length match a table entry.
PAGE 1043
Usage Information Version Description 8.4.1.0 Introduced. Use this command to configure the protocol-specific resolution value that converts the actual metric of an IPv6 route in the routing table to a scaled metric in the range 0 to 255. The UP/DOWN state of a tracked IPv6 route is determined by the user-configurable threshold (the threshold metric command) for a route’s metric in the routing table.
PAGE 1044
37 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1045
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1046
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1047
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1048
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1049
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables. Syntax Parameters clear ip ospf process-id [vrf vrf-name] [process] process-id Enter the OSPF Process ID to clear a specific process.
PAGE 1050
Version Description pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Syntax clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] Parameters Defaults process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared.
PAGE 1051
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process.
PAGE 1052
Usage Information 1052 Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the database-timer rate-limit option for the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the debug ip ospf command shown in the Example below.
PAGE 1053
Field Description ● MC- (bit used by MOSPF is not set and router cannot forward IP multicast packets) ● E + (router is able to accept AS External LSAs) ● E - (router cannot accept AS External LSAs) ● T + (router can support TOS) ● T - (router cannot support TOS) Example hi: Displays the amount of time configured for the HELLO interval. di: Displays the amount of time configured for the DEAD interval. dr: Displays the IP address of the designated router.
PAGE 1054
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1055
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. description Add a description about the selected OSPF configuration. Syntax description description To remove the OSPF description, use the no description command.
PAGE 1056
distance Define an administrative distance for particular routes to a specific IP address. Syntax distance weight [ip-address mask access-list-name] To delete the settings, use the no distance weight [ip-address mask access-list-name] command. Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110. ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address.
PAGE 1057
To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255. The default is 110. inter-area dist2 (OPTIONAL) Enter the keywords inter-area then a number to specify a distance metric for routes between areas. The range is from 1 to 255. The default is 110.
PAGE 1058
Parameters Defaults prefix-list-name Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1059
To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters Defaults prefix-list-name Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed. NOTE: BGP and ISIS routes are not available on the C-Series. BGP, ISIS, and RIP routes are not available on the S-Series. connected (OPTIONAL) Enter the keyword connected to specify that connected routes are distributed.
PAGE 1060
fast-convergence This command sets the minimum LSA origination and arrival times to zero (0), allowing more rapid route computation so that convergence takes less time. Syntax fast-convergence {number} To cancel fast-convergence, use the no fast convergence command. Parameters Defaults number Enter the convergence level desired. The higher this parameter is set, the faster OSPF converge takes place. The range is from 1 to 4. None.
PAGE 1061
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON.
PAGE 1062
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1063
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.
PAGE 1064
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart role Specify the role for your OSPF router during graceful restart. Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command.
PAGE 1065
ip ospf auth-change-wait-time OSPF provides a grace period while OSPF changes its interface authentication type. During the grace period, OSPF sends out packets with new and old authentication scheme until the grace period expires. Syntax ip ospf auth-change-wait-time seconds To return to the default, use the no ip ospf auth-change-wait-time command. Parameters Defaults seconds Enter the seconds. The range is from 0 to 300. zero (0) seconds.
PAGE 1066
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1067
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. If this command is not configured, cost is based on the auto-cost command.
PAGE 1068
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information By default, the dead interval is four times the default hello-interval. Related Commands ● ip ospf hello-interval — set the time interval between the hello packets.
PAGE 1069
Version Description pre- 6.1.1.1 Introduced on the E-Series. Usage Information The time interval between the hello packets must be the same for routers in a network. Related Commands ● ip ospf dead-interval — set the time interval before a router is declared dead. ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command.
PAGE 1070
To change to a different key on the interface, enable the new key while the old key is still enabled. Dell EMC Networking OS sends two packets: the first packet authenticated with the old key and the second packet authenticated with the new key. This process ensures that the neighbors learn the new key and communication is not disrupted by keeping the old key enabled. After the reply is received and the new key is authenticated, delete the old key. Dell EMC recommends keeping only one key per interface.
PAGE 1071
Parameters Defaults broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-to-point network. Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1072
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1073
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1074
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled.
PAGE 1075
maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths. 4 Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific.
PAGE 1076
Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1077
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced to all platforms. 7.6.1.
PAGE 1078
● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1079
● If passive-interface default is specified, then save no passive-interface interface into the running configuration. No ● ● ● passive-interface default Clear everything and revert to the default behavior. All previously marked passive interfaces are removed. May update ABR status. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires.
PAGE 1080
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. To redistribute the default route (0.0.0.
PAGE 1081
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.3 Added Route Map for BGP Redistribution to OSPF. 7.8.1.
PAGE 1082
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1083
Usage Information Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. You can configure an arbitrary value in the IP address format for each router.
PAGE 1084
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1085
Example Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. DellEMC(conf-router_ospf)# show config ! router ospf 3 passive-interface 0 TenGigabitEthernet 1/1/1/1 DellEMC(conf-router_ospf)# show ip ospf Display information on the OSPF process configured on the switch.
PAGE 1086
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. If you delete all the network area commands for Area 0, the show ip ospf command output does not list Area 0. The following describes the show ip ospf command shown in the following example. Line Beginning with Description “Routing Process...” Displays the OSPF process ID and the IP address associated with the process ID. “Supports only...
PAGE 1087
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1088
databasesummary (OPTIONAL) Enter the keywords database-summary to the display the number of LSA types in each area and the total number of LSAs. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1089
Link ID 10.2.3.2 10.2.4.2 Link ID 0.0.0.0 1.1.1.1 10.1.1.0 10.1.2.0 10.2.2.0 10.2.3.0 10.2.4.0 11.1.1.0 11.1.2.0 12.1.2.0 13.1.1.0 13.1.2.0 172.16.1.0 DellEMC> Related Commands Network (Area 0.0.0.0) ADV Router Age Seq# Checksum 13.1.1.1 676 0x80000003 0x6592 192.68.135.2 908 0x80000055 0x683e Type-5 AS External ADV Router Age Seq# 192.68.135.2 908 0x80000052 192.68.135.2 908 0x8000002a 11.1.2.1 718 0x80000002 11.1.2.1 718 0x80000002 11.1.2.1 718 0x80000002 11.1.2.1 718 0x80000002 13.1.1.
PAGE 1090
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1091
LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000010 Checksum: 0x4198 Length: 28 --More-Related Commands ● show ip ospf database — display OSPF database information. show ip ospf database external Display information on the AS external (type 5) LSAs.
PAGE 1092
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database external command shown in the following example. Field Description LS Age Displays the LSA’s age.
PAGE 1093
LS Seq Number: 0x80000007 Checksum: 0x4cde Length: 36 Network Mask: /32 Metrics Type: 2 TOS: 0 Metrics: 25 Forward Address: 0.0.0.0 External Route Tag: 43 LS age: 1868 Options: (No TOS-capability, DC) LS type: Type-5 AS External Link State ID: 24.216.12.0 Advertising Router: 20.20.20.8 LS Seq Number: 0x80000005 Checksum: 0xa00e Length: 36 Network Mask: /24 Metrics Type: 2 TOS: 0 Metrics: 1 Forward Address: 0.0.0.
PAGE 1094
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1095
Network Mask: Attached Attached Attached /24 Router: 20.20.20.8 Router: 20.20.20.9 Router: 20.20.20.7 Network (Area 0.0.0.1) LS age: 252 Options: (TOS-capability, No DC, E) LS type: Network Link State ID: 192.10.10.2 Advertising Router: 192.10.10.2 LS Seq Number: 0x80000007 Checksum: 0x4309 Length: 36 Network Mask: /24 Attached Router: 192.10.10.2 Attached Router: 20.20.20.1 Attached Router: 20.20.20.5 DellEMC# Related Commands ● show ip ospf database — display OSPF database information.
PAGE 1096
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1097
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1098
Opaque ID: 1 Unable to display opaque data LS age: 833 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.2 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000002 Checksum: 0x19c2 --More-Related Commands ● show ip ospf database — display OSPF database information. show ip ospf database opaque-as Display the opaque-as (type 11) LSA information.
PAGE 1099
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. ● show ip ospf database — display OSPF database information. show ip ospf database opaque-link Display the opaque-link (type 9) LSA information. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database opaque-link [link-stateid] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process.
PAGE 1100
Related Commands Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. ● show ip ospf database — display OSPF database information. show ip ospf database router Display the router (type 1) LSA information.
PAGE 1101
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database router command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router.
PAGE 1102
Area Border Router Number of Links: 10 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.129.1 (Link Data) Router Interface address: 192.68.129.1 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.130.1 (Link Data) Router Interface address: 192.68.130.1 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.142.
PAGE 1103
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1104
Example DellEMC# show ip ospf 100 database summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Network (Area 0.0.0.0) LS age: 1551 Options: (No TOS-capability, DC, E) LS type: Summary Network Link State ID: 192.68.16.0 Advertising Router: 192.168.17.1 LS Seq Number: 0x80000054 Checksum: 0xb5a2 Length: 28 Network Mask: /24 TOS: 0 Metric: 1 LS age: 9 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.32.0 Advertising Router: 1.1.1.
PAGE 1105
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number.
PAGE 1106
Item Description Designated Router... This line displays the ID of the Designated Router and its interface address. Backup Designated... This line displays the ID of the Backup Designated Router and its interface address. Timer intervals... This line displays the interface’s timer settings for Hello interval, Dead interval, Transmit Delay (Wait), and Retransmit Interval. Example Hello due... This line displays the amount time until the next Hello packet is sent out this interface. Neighbor Count..
PAGE 1107
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1108
show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Syntax show ip ospf [process-id | vrf vrf-name ] routes Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show the OSPF RIB information corresponding to the OSPF processes that are tied to a specific VRF.
PAGE 1109
Dell EMC Networking OS Version 9.3(0.0). Starting with Version 9.4(0.0), the metric of E2 routes in the output is displayed as an external metric, whereas until Dell EMC Networking OS Version 9.3(0.0), the number of hops to the ASBR for E2 routes are displayed in the output. Example DellEMC# show ip ospf 100 route Prefix Cost Nexthop 1.1.1.1 1 0.0.0.0 3.3.3.3 2 13.0.0.3 13.0.0.0 1 0.0.0.0 150.150.150.0 2 13.0.0.3 172.30.1.0 2 13.0.0.
PAGE 1110
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1111
Example Error Type Description Non-Dr Received packets with a destination address of ALL_DRS even though SELF is not a designated router. Self-Org Receive the self originated packet. Wrong_Len The received packet length is different to what was indicated in the OSPF header. Invld-Nbr LSA, LSR, LSU, and DDB are received from a peer which is not a neighbor peer. Nbr-State LSA, LSR, and LSU are received from a neighbor with stats less than the loading state.
PAGE 1112
● Transmit timer remaining value for each neighbor ● The LSU Q length and its highest mark for each neighbor ● The LSR Q length and its highest mark for each neighbor Example (Statistics) DellEMC(conf-if-te-1/1/3/1)# do show ip ospf statistics Interface TenGigabitEthernet 1/1/3/1 Error packets (Receive statistics) Intf-Down 0 Non-Dr 0 Self-Org 0 Wrong-Len 0 Invld-Nbr 0 Nbr-State 0 Auth-Error 0 MD5-Error 0 Cksum-Err 0 Version 0 AreaMisMatch 0 Conf-Issue 0 SeqNo-Err 0 Unknown-Pkt 0 Bad-LsReq 0 RtidZero 0 Nei
PAGE 1113
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. DellEMC# show ip ospf 10 timers rate-limit List of LSAs in rate limit Queue LSA id: 1.1.1.0 Type: 3 Adv Rtid: 3.3.3.3 Expiry time: 00:00:09.111 LSA id: 3.3.3.3 Type: 1 Adv Rtid: 3.3.3.3 Expiry time: 00:00:23.96 DellEMC# show ip ospf topology Display routers in directly connected areas.
PAGE 1114
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. To isolate problems with inter-area and external routes, use this command. In OSPF inter-area and external routes are calculated by adding LSA cost to the cost of reaching the router. If an inter-area or external route is not of correct cost, the display can determine if the path to the originating router is correct or not.
PAGE 1115
Usage Information Related Commands Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The area range command summarizes routes for the different areas. With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.
PAGE 1116
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage.
PAGE 1117
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 9.0.2.0 Introduced on the S6000.. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. LSAs are sent after the start-interval and then after hold-interval until the maximum interval is reached.
PAGE 1118
Version Description 8.3.8.0 Introduced on the S4810. OSPFv3 Commands Open shortest path first version 3 (OSPFv3) for IPv6 is supported on the platform. The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) remain unchanged. However, OSPFv3 runs on a per-link basis instead of on a per-IP-subnet basis. Most changes were necessary to handle the increased address size of IPv6. The Dell EMC Networking OS implementation of OSPFv3 is based on IETF RFC 2740.
PAGE 1119
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.2.0 Introduced on the E-Series. Before you enable IPsec authentication on an OSPFv3 area, you must first enable OSPFv3 globally on the router. Configure the same authentication policy (same SPI and key) on each interface in an OSPFv3 link.
PAGE 1120
key-encryptiontype key (OPTIONAL) Specifies if the authentication key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). null Defaults Causes an encryption policy configured for the area to not be inherited on the interface. Not configured.
PAGE 1121
area nssa Specify an area as a not so stubby area (NSSA). Syntax area area-id nssa [default-information-originate] [no-redistribution] [nosummary] To delete an NSSA, use the no area area-id nssa command. Parameters area-id Specify the OSPF area by entering a number from zero (0) to 65535. no-redistribution (OPTIONAL) Specify that the redistribute command does not distribute routes into the NSSA.
PAGE 1122
auto-cost Specify how the OSPF interface cost is calculated based on the reference bandwidth method. Syntax auto-cost [reference-bandwidth ref-bw] To return to the default bandwidth or to assign cost based on the interface type, use the no autocost [reference-bandwidth ref-bw] command. Parameters Defaults ref-bw (OPTIONAL) Specify a reference bandwidth in megabits per second. The range is from 1 to 4294967. The default is 100 megabits per second. 100 megabits per second.
PAGE 1123
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.
PAGE 1124
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the S4820T, S4810, and Z9000. The following section describes the command fields. Lines Beginning With or Including Description OSPFv3...
PAGE 1125
Parameters interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1126
RId:10.130.254.101 Seq:0x80000001 Met:20(E2) Opt:0x10(DN ) Prefix:9001::/64 -LSA:Router Age:1 LSId:0.0.0.0 RId:10.130.254.101 Seq:0x80000003 Flags:0x2(E) Opt:0x13(R E V6) #Links:1 -Type:TRNET Met:1 IntfId:1049476 NbrIntfId:1049476 NbrRId:10.160.3.37 from Te 0/7 DellEMC# Command Fields Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1127
Command History Example Example (detail) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14.1.0 The detailoption is introduced on the S4810 and S4820T. 9.13(0.0) Added support for detailed debugging. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 1128
Lines Beginning With or Including Description ● ● ● ● ● 1 - Hello packet 2 - database description 3 - link state request 4 - link state update 5 - link state acknowledgement Length: Displays the OSPFv3 packet length. Router ID: Displays the OSPFv3 router ID. Area ID: Displays the OSPFv3 area ID. Chksum: Displays the OSPFv3 checksum. debug ipv6 ospf spf Display debug information for SPF timers on OSPF IPv6 packets.
PAGE 1129
Example Lines Beginning With or Including Description 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1130
Defaults Disabled. Command Modes ROUTER OSPFv3 Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1131
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA.
PAGE 1132
Usage Information OSPFv3 graceful restart supports planned-only and/or unplanned-only restarts. The default is support for both planned and unplanned restarts. ● A planned restart occurs when you enter the redundancy force-failover rpm command to force the primary RPM to switch to the backup RPM. During a planned restart, OSPF sends out a Type-11 Grace LSA before the system switches over to the backup RPM.
PAGE 1133
Parameters null Causes an authentication policy configured for the area to not be inherited on the interface. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295. MD5 | SHA1 Authentication type: Message Digest 5 (MD5) or Secure Hash Algorithm 1 (SHA-1). key-encryptiontype (OPTIONAL) Specifies if the key is encrypted. key Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication.
PAGE 1134
ipv6 ospf cost Explicitly specify the cost of sending a packet on an interface. Syntax ipv6 ospf interface-cost Parameters Defaults interface-cost Enter a unsigned integer value expressed as the link-state metric. The range is from 1 to 65535. Default cost based on the bandwidth. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1135
Defaults 40 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1136
key-encryptiontype key (OPTIONAL) Specifies if the authentication key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1137
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 1138
Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Usage Information The time interval between hello packets must be the same for routers in a network. Related Commands ● ipv6 ospf dead-interval – specify the time interval between hello packets was received from a router.
PAGE 1139
ipv6 router ospf Enable OSPF for IPv6 router configuration. Syntax ipv6 router ospf process-id [vrf vrf-name] To exit OSPF for IPv6, use the no ipv6 router ospf process-id command. Parameters Defaults process-id Enter the process identification number. The range is from 1 to 65535. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF. None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1140
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.
PAGE 1141
Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.5 Introduced on C-Series and E-Series TeraScale. 8.4.1.3 Introduced on E-Series ExaScale.
PAGE 1142
passive-interface Disable (suppress) sending routing updates on an interface. Syntax passive—interface interface To enable sending routing updates on an interface, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1143
OSPFv3 for IPv6 routing information is not sent or received through the specified router interface. The specified interface address appears as a stub network in the OSPFv3 for IPv6 domain. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute into OSPFv3.
PAGE 1144
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. To redistribute the default route (x:x:x:x::x), use the default-information originate command.
PAGE 1145
If this command is used on an OSPFv3 process that is already active (has neighbors), all the neighbor adjacencies are brought down immediately and new sessions are initiated with the new router ID. show crypto ipsec policy Display the configuration of IPsec authentication and encryption policies. Syntax Parameters Defaults show crypto ipsec policy [name name] name name (OPTIONAL) Displays configuration details about a specified policy. No default behavior or values.
PAGE 1146
Transform set : esp-3des esp-md5-hmac Crypto IPSec client security policy data Policy name : OSPFv3-0-501 Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0 c30808825fb5 Inbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Outbound ESP Cipher Key
PAGE 1147
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1148
in use settings : {Transport, } replay detection support : N STATUS : ACTIVE inbound esp sas outbound esp sas Interface: TenGigabitEthernet 1/1/2/1 Link Local address: fe80::201:e8ff:fe40:4d11 IPSecv6 policy name: OSPFv3-1-600 inbound ah sas outbound ah sas inbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay d
PAGE 1149
Parameters process-number Enter the OSPF process number. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. databasesummary (OPTIONAL) Enter the keyword database-summary to view a summary of database LSA information. external (OPTIONAL): Enter the keyword external to display the external link states.
PAGE 1150
Usage Information Example (gracelsa) Version Description 7.8.1.0 Added support for C-Series. The show ipv6 ospf database command output displays detailed information on the OSPFv3 database, including link-state advertisements (LSAs). DellEMC# show ipv6 ospf 3 database grace-lsa ! Type-11 Grace LSA (Area 0) LS Age : 10 Link State ID : 6.16.192.66 Advertising Router : 100.1.1.
PAGE 1151
Neighbor ID Interface 63.114.8.36 Example (external) Pri 1 State Dead Time FULL/DR 00:00:37 Interface ID 4 Te 1/1/4/1 DellEMC# show ipv6 ospf database external OSPFv3 Router with ID (10.160.3.37) (Process ID 6) AS External Link States (Area 0) LS Age: 1651 LS Type: OSPFv3 AS external LSA Link State ID: 0.0.0.1 Advertising Router: 10.130.254.
PAGE 1152
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1153
show ipv6 ospf neighbor Display the OSPF neighbor information on a per-interface basis. Syntax Parameters show ipv6 ospf [process-number] [vrf vrf-name] neighbor [interface] process-number Enter the OSPF process number. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display OSPF neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
PAGE 1154
Example DellEMC# show ipv6 ospf 3 neighbor te 1/1/2/1 Neighbor ID 63.114.8.36 Pri State 1 FULL/DR Dead Time 00:00:38 4 Interface ID Interface Te 1/1/2/1 DellEMC# snmp context Configure SNMPv3 context name to map multiple OSPFv3 VRF instances. Syntax snmp context {context-name} To clear snmp context, use the no snmp context {context-name} command. Parameters Defaults context-name Enter the SNMP context name. The maximum length is 32 alphanumeric characters. None.
PAGE 1155
Defaults holdtime Enter a number as the hold time. The range is from 0 to 2147483647. The default is 10 seconds. When configured in milli seconds, 200 is the least value that is allowed to be configured. msec Enter the keyword msec to specify the time interval value in milli seconds. NOTE: If you do not specify the msec option, the timer values are considered as seconds.
PAGE 1156
38 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1157
Related Commands Version Description 8.4.2.0 Introduced on the E-Series. 7.7.1.0 Introduced on the E-Series. ● ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name test [l2–switch] To remove a redirect list from an interface, use the no ip redirect-group name command.
PAGE 1158
NOTE: Apply the redirect list to physical, VLAN, or LAG interfaces only. The Layer2 PBR option matches the layer2 traffic flow. If you un-configure this option, then the Layer2 traffic is not matched. You can apply the l2–switch option to redirect Layer2 traffic only on a VLAN interface. This VLAN interface must be configured with an IP address for ARP resolution. NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces.
PAGE 1159
permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: ● If you know the filter sequence number, use the no seq sequence-number syntax command.
PAGE 1160
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1161
● rst = reset the connection ● syn = synchronize sequence number ● urg = urgent field Defaults source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1162
[bit] [operator]{source-port source-port| source-port-range start-port end-port} {destination-port destination-port| destination-port-range startport - end-port} To delete a filter, use the no seq sequence-number command. Parameters 1162 sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the keyword IP address of the forwarding router.
PAGE 1163
destination-port- Enter the keywords destination-port-range then the range of the start port range to end port to be matched in the ACL rule in the ICAP rule. Defaults none Command Modes REDIRECT-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1164
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The show cam pbr command displays the PBR CAM content.
PAGE 1165
seq 35 redirect seq 40 redirect seq 45 redirect Track 200 [up], 42.1.1.2 43.1.1.2 31.1.1.2 Next-hop icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20) tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30) track 200 ip 12.0.0.0 255.0.0.197 13.0.0.0 255.0.0.
PAGE 1166
39 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
PAGE 1167
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1168
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
PAGE 1169
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled.
PAGE 1170
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1171
Version Description 8.1.1.0 Introduced on the E-Series. 6.1.1.0 Added support for the VLAN interface. ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1.
PAGE 1172
Parameters Defaults ext-access-list Enter the name of an extended access list. none Command Modes INTERFACE Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1173
NOTE: Applies to specific VRF if input is provided, else applies to default VRF. access-list Defaults Enter the name of a standard access list. Maximum 16 characters. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1174
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 1175
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced The access name is an extended IP access list that denies PIM register packets to RP at the source DR based on the multicast and group addresses. Do not enter this command before creating the access-list.
PAGE 1176
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. pre- 6.1.1.1 Introduced on the E-Series. First-hop routers use this address by to send register packets on behalf of source multicast hosts. The RP addresses are stored in the order in which they are entered.
PAGE 1177
Usage Information Version Description 9.11(0.0) Introduced the acl-name parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 1178
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. The interface must be enabled (the no shutdown command) and not have the switchport command configured. Multicast must also be enabled globally (using the ip multicast-lag-hashing command). PIM is supported on the port-channel interface. ip pim sparse-mode sg-expiry-timer Enable expiry timers globally for all sources.
PAGE 1179
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. 7.7.1.1 Introduced This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL. Even though the FHR nodes act as RPs, these nodes still send Register encap messages to themselves and expect to receive a Register stop message (for Anycast RP support).
PAGE 1180
Usage Information Version Description 7.5.1.0 Introduced on the E-Series. Dell EMC Networking OS supports standard access lists for the SSM range. You cannot use extended ACLs for configuring the SSM range. If you configure an extended ACL and then used in the ip pim ssm-range {access list name} configuration, an error is reported.
PAGE 1181
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. This command is applicable to last hop routers on the shared tree towards the rendezvous point (RP). show ip pim bsr-router View information on the Bootstrap router.
PAGE 1182
This system is a candidate BSR Candidate BSR address: 7.7.7.7, priority: 0, hash mask length: 30 DellEMC# show ip pim interface View information on the interfaces with IP PIM enabled. Syntax show ip pim [vrf vrf-name] interface Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on this VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1183
Field Description Query Intvl Displays the query interval for Router Query messages on that interface (configured with ip pim query-interval command). DR Prio Displays the Designated Router priority value configured on the interface (use the ip pim dr-priority command). DR Displays the IP address of the Designated Router for that interface. The show ip pim interface command does not display information corresponding to the loop-back interfaces.
PAGE 1184
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim neighbor command shown in the following example. Field Description Neighbor address Displays the IP address of the PIM neighbor. Example Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found.
PAGE 1185
Example Example (Mapping) Example (Address) Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1186
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 1187
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.1 Support for the display of PIM-SM snooping status was added on E-Series. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1188
show ip pim tib View the PIM tree information base (TIB). Syntax show ip pim [vrf vrf-name] tib [group-address [source-address]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D). source-address (OPTIONAL) Enter the source address in dotted decimal format (A.
PAGE 1189
Field Description ● ● ● ● ● ● L = local to the multicast group P = route was pruned R = the forwarding entry is pointing toward the RP F = Dell EMC Networking OS is registering this entry for a multicast source T = packets were received via Shortest Tree Path J = first packet from the last hop router is received and the entry is ready to switch to SPT ● K = acknowledge pending state Example Incoming interface Displays the reverse path forwarding (RPF) interface towards the RP/ source.
PAGE 1190
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero. Defaults none Command Modes EXEC Privilege Command History Related Commands Version Description 9.11.3.
PAGE 1191
ipv6 pim bsr-border Define the border of IPv6 PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ipv6 pim bsr-border To return to the default value, use the no ipv6 pim bsr-border command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 9.14(1.
PAGE 1192
Version Description 9.14(1.0) Introduced on the C9010, S3048-ON, S3100 Series, S4048-ON, S4048T-ON, S6000-ON, S6010-ON, S6100-ON, Z9100-ON. ipv6 pim dr-priority Change the designated router (DR) priority for the IPv6 interface. Syntax ipv6 pim dr-priority priority-value To remove the DR priority value assigned, use the no ipv6 pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1.
PAGE 1193
ipv6 pim rp-address Configure a static PIM rendezvous point (RP) address for a group. First-hop routers use this address to send register packets on behalf of the source multicast host. Syntax ipv6 pim [vrf vrf-name] rp-address address {group-address group-address mask} [override] To remove an RP address, use the no ipv6 pim re-address address group-address mask [override] command.
PAGE 1194
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information.
PAGE 1195
Usage Information Enable the interface (use the no shutdown command) and not have the switchport command configured. Also enable Multicast globally. PIM is supported on the port-channel interface. ipv6 pim sparse-mode sg-expiry-timer Enable expiry timers globally for all sources. Syntax ipv6 pim [vrf vrf-name] sparse-mode sg-expiry-timer seconds To disable configured timers and return to default mode, use the no ipv6 pim sparse-mode sgexpiry-timer command.
PAGE 1196
Usage Information Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. PIM leaf routers join the shortest path tree immediately after the first packet arrives from a new source. show ipv6 pim bsr-router View information on the bootstrap router. Syntax show ipv6 pim [vrf vrf-name] bsr-router Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF.
PAGE 1197
Example Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010.
PAGE 1198
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. mapping (OPTIONAL) Enter the keyword mapping to display the multicast groups-to-RP mapping and information on how RP is learned. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format to view RP mappings for a specific group. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1199
RP: 100::1, v2 DellEMC# show ipv6 pim summary View information about PIM-SM operation. Syntax Parameters show ipv6 pim [vrf vrf-name] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1200
show ipv6 pim tib View the IPv6 PIM multicast-routing database (tree information base — tib). Syntax show ipv6 pim [vrf vrf-name] tib [group-address [source-address]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1201
40 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1202
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1203
Version Description 9.11(0.0) Introduced GRE protocol support. ip access-group Assign an IP access list (IP ACL) in the monitor session mode. Syntax Parameters Defaults ip access-group access-list-name access-list-name Enter the name of a configured access list, up to 140 characters. Not enabled. Command Modes MONITOR SESSION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1204
Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1205
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.
PAGE 1206
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000-ON, Z9500. ● monitor session — enable a monitoring session. ● show monitor session — display the monitor session.
PAGE 1207
source TenGigabitEthernet 1/1/1/1 destination Port-channel 1 direction rx show monitor session Display information about monitoring sessions. Syntax show monitor session {session-ID} [access-list] To display monitoring information for all sessions, use the show monitor session command. Parameters Defaults session-ID (OPTIONAL) Enter a session identification number. The range is from 0 to 65535. [access-list] (OPTIONAL) Enter the access-list keyword to display the ACLs applied to monitor sessions.
PAGE 1208
Example DellEMC# show monitor session 1 SessID Source Destination Dest IP DSCP TTL Drop Rate ------ -------------------------- ------ ---1 Te 1/1/2/1 remote-ip 0.0.0.0 0 0 No N/A DellEMC# Dir Mode Source IP Gre-Protocol FcMonitor --- ---- ------------------- --------rx Port 0.0.0.0 N/A yes DellEMC# show monitor session SessID Source Destination Dest IP DSCP TTL Drop Rate ------ -------------------------- ------ ---1 Te 1/1/2/1 remote-ip 0.0.0.
PAGE 1209
Usage Information Example Related Commands Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1210
NOTE: This option is applicable only with drop monitor session. Defaults destination Enter the keyword destination to specify the destination interface. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1211
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1212
41 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1213
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1214
To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN. primary Enter the keyword primary to configure the VLAN as a primary VLAN. none Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific.
PAGE 1215
Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input. none Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1216
Defaults Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1217
42 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1218
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Syntax disable To enable PVST+, use the no disable command. Defaults Disabled.
PAGE 1219
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
PAGE 1220
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1221
show spanning-tree pvst View the Per-VLAN spanning tree configuration. Syntax Parameters Defaults show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1222
Usage Information Example (Brief) Version Description 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples.
PAGE 1223
Port 131 (TenGigabitEthernet 1/1/2/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.131 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1224
Related Commands ● spanning-tree pvst — configure PVST+ on an interface. spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
PAGE 1225
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series, C-Series, and S-Series. 8.3.7.
PAGE 1226
spanning-tree pvst vlan 3 cost 18000 no shutdown DellEMC(conf-if-te-1/1/1/1)# end DellEMC# Related Commands ● show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN.
PAGE 1227
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1228
Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1229
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1230
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced.
PAGE 1231
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. ● vlan bridge-priority — sets the bridge-priority value.
PAGE 1232
43 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1233
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. service-class bandwidth-percentage Specify a minimum bandwidth for queues.
PAGE 1234
Parameters Defaults queue Enter a value from 0 to 7. For each dot1p Priority, the default CoS queue value is: ● Dot1p Priority : 0 1 2 3 4 5 6 7 ● Queue : 1 0 2 3 4 5 6 7 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1235
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information trust dot1p, do1p-priority, service-class dynamic dot1; all these features work over the mapping in this command output. Related Commands ● service-class dot1p-mapping — Identifies the class map.
PAGE 1236
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1237
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1238
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1239
dot1p Queue ID 5 5 6 6 7 7 Command Modes ● INTERFACE ● CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1240
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify data traffic into one of eight classes . Dell EMC Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
PAGE 1241
buffer-stats-snapshot Enable the buffer statistics tracking utility and enter the Buffer Statistics Snapshot configuration mode. You must enable this utility to be able to configure the parameters for buffer statistics tracking. Syntax [No] buffer-stats-snapshot To disable the buffer statistics tracking utility, enter the disable command from the BUFFER-STATSSNAPSHOT mode. Default By default, buffer statistics tracking is disabled.
PAGE 1242
Defaults cpu-qos Enter the keyword cpu-qos to assign this Class Map to control plane traffic only (CoPP). layer2 Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Layer 3 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1243
clear qos statistics Clear qos statistics clears statistics from show qos statistics. Syntax Parameters Defaults clear qos statistics interface-name interface-name Enter one of the following keywords: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1244
description Add a description to the selected policy map or QoS policy. Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the policies (80 characters maximum). none Command Modes CONFIGURATION (policy-map-input and policy-map-output; conf-qos-policy-in and conf-qos-policy-out; wred) Command History Related Commands This guide is platform-specific.
PAGE 1245
Parameters seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100. By default, the sequence number are assigned in multiples of five. access-groupname Enter the ACL name whose contents are used as the match criteria in determining if packets belong to the class the class-map specifies. set-ip-dscp value (OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63.
PAGE 1246
match ip dscp Use a differentiated services code point (DSCP) value as a match criteria. Syntax [seq sequence number] match {ip | ipv6 | ip-any} dscp dscp-list [set-ipdscp value] To remove a DSCP value as a match criteria, use the no [seq sequence number] match {ip | ipv6 | ip-any} dscp dscp-list [[multicast] set-ip-dscp value] command. Parameters seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100.
PAGE 1247
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive. Up to 64 IP DSCP values can be matched in one match statement. For example, to indicate IP DCSP values 0 1 2 3 4 5 6 7, enter either the match ip dscp 0,1,2,3,4,5,6,7 or match ip dscp 0-7 command.
PAGE 1248
Usage Information Version Description 9.5(0.0) Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the keyword multicast . Added support for the DSCP Marking option for the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1249
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.1.0 Introduced on the E-Series. Usage Information To access this command, enter the class-map command.
PAGE 1250
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.1.0 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands ● class-map — identifies the class map.
PAGE 1251
Related Commands ● class-map — identifies the class map. policy-aggregate Allow an aggregate method of configuring per-port QoS via policy maps. An aggregate QoS policy is part of the policy map (output) applied on an interface. Syntax policy-aggregate qos-policy-name To remove a policy aggregate configuration, use the no policy-aggregate qos-policy-name command. Parameters Defaults qos-policy-name Enter the name of the policy map in character format (32 characters maximum).
PAGE 1252
policy-map-input Create an input policy map. Syntax policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] To remove an input policy map, use the no policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] command. Parameters Defaults policy-map-name Enter the name of the policy map in character format (32 characters maximum). cpu-qos Enter the cpu-qos keyword to assign this ACL to control plane traffic only. layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map.
PAGE 1253
policy-map-output Create an output policy map. Syntax policy-map-output policy-map-name To remove a policy map, use the no policy-map-output policy-map-name command. Parameters Defaults policy-map-name Enter the name for the policy map in character format (32 characters maximum). none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1254
Defaults cpu-qos (OPTIONAL) Enter the keyword cpu-qos keyword to assign this ACL to control plane traffic only. layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Layer 3 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1255
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1256
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1257
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1258
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the resequence option for class-map on all the Dell EMC Networking OS platforms. If there is no option to create a new rule and to avoid reconfiguring class-map, use the resequence class-map command.
PAGE 1259
Usage Information Version Description 7.4.1.0 E-Series Only: Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series. You can attach a single policy-map to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. NOTE: The service-policy commands are not allowed on a port channel.
PAGE 1260
Usage Information A single policy-map can be attached to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. Related Commands ● policy-map-output — creates an output policy map. service-queue Assign a class map and QoS policy to different queues.
PAGE 1261
Usage Information There are eight queues per interface on the S6000 and four queues on the S-Series. This command assigns a class map or QoS policy to different queues. Related Commands ● class-map — identifies the class map. ● service-policy input — applies an input policy map to the selected interface. ● service-policy output — applies an output policy map to the selected interface. set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value.
PAGE 1262
show qos class-map View the current class map information. Syntax show qos class-map [class-name] Parameters Defaults class-name (Optional) Enter the name of a configured class map. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option on all the Dell EMC Networking OS platforms.
PAGE 1263
Parameters 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. summary To view a policy map interface summary, enter the keyword summary and optionally one of the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1264
Example (IPv4) Version Description 7.4.1.0 E-Series only: Added trust IPv6 diffserv . 6.2.1.1 Introduced on the E-Series.
PAGE 1265
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1266
show qos policy-map-output View the output QoS policy map details. Syntax show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] Parameters policy-map-name Enter the policy map name. qos-policyoutput qos- Enter the keyword qos-policy-output then the QoS policy name. policy-name Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1267
show qos qos-policy-input View the input QoS policy details. Syntax Parameters Defaults show qos qos-policy-input [qos-policy-name] qos-policy-name Enter the QoS policy name. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 1268
Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1269
wred-profile interface interface Defaults Enter the keywords wred-profile and optionally one of the following keywords and slot/po or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/ slot/port/subport information.
PAGE 1270
Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1271
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on the S6100 and Z9100. This command displays the details of total number of packets marked with ECN and the total number of packets that got dropped. The total number of packets includes both the packets marked with ECN and packets not marked with ECN.
PAGE 1272
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series.
PAGE 1273
The following table describes the mapping between the threshold weight of the shared buffer on the queue. It also shows the percentage of the available shared buffer used by the queues for each of the corresponding threshold weights of the shared buffer: sharedthresholdweight on the queue % of available shared buffer that can be consumed by the queue 0 No dynamic sharing; shared buffer = 0. 1 0.77% 2 1.54% 3 3.03% 4 5.88% 5 11.11% 6 20% 7 33.33% 8 50% 9 66.67% 10 80% 11 88.
PAGE 1274
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. This feature allows you to determine if the CAM has enough space available before applying the configuration on an interface.
PAGE 1275
To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360. max number Enter the keyword max then the maximum threshold number for the WRED profile. The range is from 1 to 9360 KB. max-drop-drop Enter the keyword max-drop-drop followed by the maximum number of packets for the WRED profile.
PAGE 1276
fallback Defaults Enter the keyword fallback to classify packets according to their DSCP or dot1p value as a secondary option in case no match occurs against the configured class maps. none Command Modes CONFIGURATION (conf-policy-map-in) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1277
Table 5. Default Mapping (continued) DSCP/CP hex DSCP Range (XXX) Definition Traditional IP Precedence S6000 Internal Queue ID S-Series Internal Queue ID DSCP/CP Decimal 011XXX AF3 Flash 3 1 16–31 010XXX AF2 Immediate 2 1 16–31 001XXX AF1 Priority 1 0 0–15 000XXX BE (Best Effort) Best Effort 0 0 0–15 unsequence class-map all Allows you to rewrite the running configuration for all the class-map match-any without sequence number.
PAGE 1278
Defaults When WRED green is applied, default WRED yellow profiles take effect and vice-versa. Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 1279
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. When you enable wred ecn, and the number of packets in the queue is below the minimum threshold, packets are transmitted per the usual WRED treatment.
PAGE 1280
Usage Information Example If the average queue size is more than the maximum threshold of WRED, the packet is dropped. If the average queue size is between the minimum and maximum threshold values, the decision to drop or queue the packet is taken based on the packet drop probability. The probability that a packet is dropped depends on the minimum threshold, maximum threshold, and mark probability denominator.
PAGE 1281
rate shape Define the rate-shaping method to be either as a measure of bytes or packets for each of the hierarchical QoS (HQoS) nodes at the leaf level to be applied to each queue. Syntax Parameters Default [no] rate-shape [kbps | pps] peak-rate [burst-KB/Packets] [committed [kbps | pps] committed-rate [burst-KB/Packets]] kbps Enter the keyword kbps to specify the committed rate limit in Kilobits per second (Kbps). Specify this value as a multiple of 64. The range is from 0 to 40000000.
PAGE 1282
Usage Information Version Description 9.3(0.0) Added support for committed rate and committed burst size, and for configuration of rate limits on the S6000 platform. If you specify the pps keyword after the rate-shape command, the peak rate, peak burst, committed rate and committed burst are all considered to be values as a measure of packets. If you do not specify the pps or kbps keyword, the peak and committed rate settings are considered to be values in Mbps.
PAGE 1283
string Default Enter the WRED profile name. It is a string of up to 32 characters. Or use one of the five pre-defined WRED profile names. Pre-defined Profiles: wred_drop, wred-ge_y, wred_teng_y, wred_teng_. This parameter applies only if you specify a weight factor. All queues on backplane ports operate in tail-drop (best-effort traffic) mode by default. There is no default WRED green or yellow profile. The default weight is 0.
PAGE 1284
Defaults None Command Modes CONFIG-COLOR-MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1285
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL.
PAGE 1286
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. Version 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information If the specified color-map does not exist, the Diffserv Manager (DSM) creates a color map and sets all the DSCP values to green (low drop precedence). Example The following example assigns the color map, bat-enclave-map, to interface te 1/1/1/1.
PAGE 1287
show qos dscp-color-map Display the DSCP color map for one or all interfaces. Syntax Parameters Defaults show qos dscp-color-map map-name map-name Enter the name of the color map. None Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1288
44 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1289
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1290
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1291
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic.
PAGE 1292
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command.
PAGE 1293
Related Commands ● redistribute — allows you to redistribute routes learned by other methods. description Enter a description of the RIP routing protocol. Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the RIP protocol (80 characters maximum). none Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1294
Defaults ip-address (OPTIONAL) Enter the IP address, in dotted decimal format (A.B.C.D), of the host or network to receive the new distance metric. mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x). prefix-name (OPTIONAL) Enter a configured prefix list name. weight = 120 Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1295
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 1296
Defaults interface (OPTIONAL) Identifies the interface type slot/port as one of the following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1297
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1298
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1299
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1300
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ● ip poison-reverse — sets the prefix for RIP routing updates. maximum-paths Set RIP to forward packets over multiple paths.
PAGE 1301
Usage Information Version Description pre- 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command. Parameters Defaults ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Not configured.
PAGE 1302
network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command. Syntax network ip-address To disable RIP for a network, use the no network ip-address command. Parameters Defaults ip-address Specify an IP network address in dotted decimal format. You cannot specify a subnet. No RIP network is configured. Command Modes ROUTER RIP Command History Usage Information This guide is platform-specific.
PAGE 1303
Parameters Defaults prefix-list-name Enter the name of an established Prefix list to determine which incoming routes are modified. offset Enter a number from zero (0) to 16 to be applied to the incoming route metric matching the access list specified. If you set an offset value to zero (0), no action is taken.
PAGE 1304
output-delay Set the interpacket delay of successive packets to the same neighbor. Syntax output-delay delay To return to the switch software defaults for interpacket delay, use the no output-delay command. Parameters Defaults delay Specify a number of milliseconds as the delay interval. The range is from 8 to 50. Not configured. Command Modes ROUTER RIP Command History Usage Information This guide is platform-specific.
PAGE 1305
● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1306
Parameters Defaults connected Enter the keyword connected to specify that information from active routes on interfaces is redistributed. static Enter the keyword static to specify that information from static routes is redistributed. Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1307
level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16. value route-map map- name Defaults (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1308
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1309
Usage Information Example Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. To enable RIP, assign a network address using the network command. DellEMC(conf)# router rip DellEMC(conf-router_rip)# ● network — enables RIP. ● exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration.
PAGE 1310
router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1/1/1 DellEMC(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Syntax show ip rip database [ip-address mask] Parameters ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If you enter an IP address, also enter a mask for that IP address.
PAGE 1311
Example Field Description 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24... Lists the routes and the sources advertising those routes. DellEMC# show ip rip database Total number of routes in RIP database: 1624 204.250.54.0/24 [50/1] via 192.14.1.3, 00:00:12, TenGigabitEthernet 1/15/1 204.250.54.0/24 auto-summary 203.250.49.0/24 [50/1] via 192.13.1.3, 00:00:12, TenGigabitEthernet 1/14/1 203.250.49.0/24 auto-summary 210.250.40.0/24 [50/2] via 1.1.18.
PAGE 1312
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Example DellEMC# show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.0.0 passive-interface TenGigabitEthernet 2/1/1 neighbor 20.20.20.
PAGE 1313
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1314
Related Commands 1314 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ● ip rip receive version — sets the RIP version the interface receives.
PAGE 1315
45 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1316
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1317
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1318
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1319
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
PAGE 1320
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1321
show rmon Display the RMON running status including the memory usage. Syntax show rmon Defaults none Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1322
brief Defaults (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) 1322 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1323
13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table. Syntax Parameters Defaults show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format.
PAGE 1324
options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none. event community: event last time sent: none event owner: event status: OK RMON event entry 112 description: event type: LOG. event community: event last time sent: none event owner: event status: OK RMON event entry 113 description: event type: SNMP TRAP. event community: private event last time sent: none event owner: event status: OK RMON event entry 114 description: event type: LOG and SNMP TRAP.
PAGE 1325
Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1326
show rmon history Display the contents of the RMON Ethernet history table. Syntax show rmon history [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an easy-to-read format none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1327
Defaults none Command Modes EXEC Command History Usage Information Example (Index) Example (Brief) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1328
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1329
46 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1330
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1331
Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1332
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. ● protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled.
PAGE 1333
forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters Defaults seconds Enter the number of seconds that Dell EMC Networking OS waits before transitioning RSTP to the forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1334
milli-second Defaults Enter the keywords milli-second to configure a hello time on the order of milliseconds. The range is from 50 to 950 milliseconds 2 seconds Command Modes CONFIGURATION RSTP (conf-rstp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1335
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1336
Usage Information Example Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. RSTP is not enabled when you enter RSTP mode. To enable RSTP globally on the system, use the no disable command from RSTP mode.
PAGE 1337
Example DellEMC(conf-rstp)# show config ! protocol spanning-tree rstp no disable bridge-priority 16384 show spanning-tree rstp Display the RSTP configuration. Syntax Parameters show spanning-tree rstp [brief] [guard] brief (OPTIONAL) Enter the keyword brief to view a synopsis of the RSTP configuration information. guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state.
PAGE 1338
Example (Brief) Field Description Instance RSTP instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), disabled (DIS), or shut down (EDS Shut). Guard Type Types of STP guard configured (Root, Loop, or BPDU guard) DellEMC# show spanning-tree rstp brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 8192, Address 0001.e805.e306 Root Bridge hello time 4, max age 20, forward delay 15 Bridge ID Priority 16384, Address 0001.e801.
PAGE 1339
Example (Guard) DellEMC# show spanning-tree rstp guard Interface Name Instance Sts Guard type ---------- -------- ------------------Te 1/1/1/1 0 INCON(Root) Rootguard Te 1/1/2/1 0 FWD Loopguard Te 1/1/3/1 0 BLK Bpduguard spanning-tree rstp Configure an RSTP interface with one of these settings: port cost, edge port with optional bridge port data unit (BPDU) guard, port priority, loop guard, or root guard.
PAGE 1340
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added support for the optional guard keyword on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 1341
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled Command Modes CONFIGURATION (conf-rstp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1342
47 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant.
PAGE 1343
Defaults exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. dot1x Enter the keyword dot1x to send accounting information when a dot1x user has logged in. commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role.
PAGE 1344
Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
PAGE 1345
aaa authentication login method-list none command is applied. To prevent the accounting records from being generated for sessions that do not have user names associated to them, use the aaa accounting suppress command. accounting Apply an accounting method list to terminal lines. Syntax Parameters Defaults accounting {exec | commands {level | role role-name} method-list exec Enter the keyword exec to apply an EXEC level accounting method list.
PAGE 1346
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1347
Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1348
Command Modes LINE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1349
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1350
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1351
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS. privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands.
PAGE 1352
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To define a password for the level to which you are assigning privilege or access, use the enable password command.
PAGE 1353
Version Description pre-6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication, use the service obscure-passwords command. Defaults Disabled.
PAGE 1354
Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | method-list-name} method [... method2] command.
PAGE 1355
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell EMC Networking OS uses the methods defined for Enable access instead. Methods configured with the aaa authentication enable command are evaluated in the order they are configured.
PAGE 1356
Usage Information Version Description 9.11(0.0) Included a prompt to force the users to re-authenticate, when re-authentication is enabled. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0 Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.
PAGE 1357
To disable the re-authentication option, use the no aaa reauthenticate enable command. Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced this command.
PAGE 1358
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. ● line — applies an authentication method list to the designated terminal lines.
PAGE 1359
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1360
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1361
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1362
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.6.0.0 Revised introductory and usage guidelines description. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1363
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1364
period is not enabled. This parameter enhances the security of the switch by locking out sessions on the Telnet or SSH sessions for which there has been a consecutive failed login attempts. The console is not locked out. user-lockoutperiod minutes (OPTIONAL) Enter the keyword user-lockout-period then the number of minutes. The range is from 1 to 1440 minutes. The default is 0 minutes and the lockout-period is not enabled.
PAGE 1365
Example In the following example, after 5 un-successful login attempts, the session (SSH/TELNET) goes into a locked state for 5 minutes. If all the 10 sessions are locked out with 5 un-successful attempts in each session, no users can login during the lockout-period. DellEMC(conf)# password-attributes max-retry 5 lockout-period 5 Related Commands ● password — specifies a password for users on terminal lines. secure-cli enable Enable the secured CLI mode.
PAGE 1366
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security. When the passwords are encrypted, you cannot return them to plain text unless you re-configure them.
PAGE 1367
Example Version Description pre-6.1.1.0 Introduced on the E-Series. DellEMC# show privilege Current privilege level is 15. DellEMC# DellEMC# show privilege Current privilege level is 14. DellEMC# DellEMC# show privilege Current privilege level is 10. DellEMC# Related Commands ● privilege level (CONFIGURATION mode) — assign access control to different command modes. show users Allows you to view information on all users logged in to the switch.
PAGE 1368
Usage Information Example Related Commands The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lines currently in use. User Displays the user name of all users logged in. Host(s) Displays the terminal line status. Location Displays the IP address of the user.
PAGE 1369
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1370
privilege level Enter the keyword privilege then a number from zero (0) to 15. role role-name Enter the keyword role followed by the role name to associate with that user ID. secret Enter the keyword secret then the encryption type. sha256-password Enter the keyword sha256-password then the encryption-type or the password. Defaults The default encryption type for password option is 0. The default encryption type for secret option is 5. The default encryption type for sha256-password option is 8.
PAGE 1371
● ● ● ● Related Commands A A A A minimum minimum minimum minimum of of of of one one one one lower case letter (a to z) upper case letter (A to Z) numeric character (0 to 9) special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") ● password — specifies a password for users on terminal lines. ● show running-config — views the current configuration. RADIUS Commands The following RADIUS commands are supported by Dell EMC Networking OS. client Configures trusted DAC clients.
PAGE 1372
client-key Configures global shared key for the trusted DAC clients. Syntax client—key [encryption-type] key To remove the shared key configuration, enter the no client-key command. Defaults Parameters None. encryption-type: (OPTIONAL) Enter either 0 or 7 as the encryption type for the key entered. The options are: ● 0 — is the default and means the key is not encrypted and stored as clear text. ● 7 — means that the key is encrypted and hidden.
PAGE 1373
coa-disable-port Configure NAS to reject disable-port requests from DAC. Syntax coa-disable-port To undo this configuration, enter the no coa-disable-port command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Usage Information ● Configure no coa-disable-port DAS to drop radius CoA disable-port requests from DAC. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1374
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1375
To undo this configuration, enter the no disconnect-user command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1376
● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number.
PAGE 1377
Usage Information ● Optionally specify dynamic authorization port number. Default port is 3799. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1378
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1379
● radius-server retransmit — sets the number of times the RADIUS server attempts to send information. ● radius-server timeout — sets the time interval before the RADIUS server times out. radius-server host Configure a RADIUS server host. Syntax Parameters radius-server host {hostname | ipv4-address | ipv6-address} [auth-port port-number] [acct-port port-number] [retransmit retries] [timeout seconds] [key [encryption-type] key] hostname Enter the name of the RADIUS server host.
PAGE 1380
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1381
Syntax radius-server vrf vrf-name [source-interface interface] To delete the association between a RADIUS server group and a VRF and source interface, use the no radius-server vrf vrf-name [source-interface interface] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a RADIUS server group with that VRF.
PAGE 1382
Example DellEMC(conf)#radius-server group group1 DellEMC(conf-radius-group)#radius-server vrf vrf1 source-interface tengigabitethernet 1/1/3/1 DellEMC(conf)#radius-server group group2 DellEMC(conf-radius-group)#radius-server vrf default radius-server key Configure a key for all RADIUS communications between the switch and the RADIUS host server. Syntax radius-server key [encryption-type] key To delete a password, use the no radius-server key command.
PAGE 1383
If you configure the key parameter in the radius-server host command, the key configured with the radius-server key command is the default key for all RADIUS communications. Related Commands ● radius-server host — configures a RADIUS host. radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable.
PAGE 1384
To return to the default value, use the no radius-server timeout command. Parameters Defaults seconds Enter the number of seconds between an unsuccessful attempt and the Dell EMC Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds. 5 seconds Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1385
The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. replay-protection-window Configure replay protection window period to drop the duplicate packets.
PAGE 1386
TACACS+ Commands Dell EMC Networking OS supports TACACS+ as an alternate method for login authentication. tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command . Parameters Defaults group-name Enter the name of the TACACS server group. Not configured.
PAGE 1387
Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1388
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1389
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. You can associate a TACACS server group with a VRF. Example Related Commands ● aaa authentication login — specifies the login authentication method. ● tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server host Specify a TACACS+ host.
PAGE 1390
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times.
PAGE 1391
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1392
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1393
dot1x authentication (Configuration) Enable dot1x globally; dot1x must be enabled both globally and at the interface level. Syntax dot1x authentication To disable dot1x on globally, use the no dot1x authentication command. Defaults Disabled. Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1394
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1395
Usage Information Version Description 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed attempts, the interface is moved to the authentication failed VLAN. After the authentication VLAN is assigned, the port-state must be toggled to restart authentication.
PAGE 1396
Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1397
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1398
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. ● interface range — configure a range of interfaces. dot1x port-control Enable port control on an interface.
PAGE 1399
dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command. Parameters Defaults seconds Enter the number of seconds. The range is from 1 to 65535. The default is 30. 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1400
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1401
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters Defaults seconds Enter a time-out value in seconds.
PAGE 1402
Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 1403
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. show dot1x interface Display the 802.1X information on an interface.
PAGE 1404
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. DellEMC#show dot1x interface fortyGigE 1/10 802.
PAGE 1405
SSH and SCP Commands Dell EMC Networking OS supports secure shell (SSH) protocol version 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted and use authentication. crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1406
NOTE: Only a user with superuser permissions should generate host-keys. Example Related Commands DellEMC(conf)# crypto key generate rsa Enter key size <1024-2048>. Default<1024> : Host key already exists. Overwrite (y/n)?y Generating 1024-bit SSHv2 RSA key. ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! DellEMC(conf)# ● ip ssh server — enables the SSH server. ● show crypto — displays the SSH host public keys. crypto key zeroize rsa Removes the generated RSA host keys and zeroize the key storage location.
PAGE 1407
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1408
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command. Related Commands ● ip ssh server — enables the SSH and SCP server on the switch.
PAGE 1409
Usage Information This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh challenge–response–authentication Enable challenge response authentication for SSHv2.
PAGE 1410
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip ssh connection-rate-interval Configure the rate interval in which the maximum number of SSH connections can be attempted.
PAGE 1411
To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbasedauthentication enable command. Parameters Defaults enable Enter the keyword enable to enable hostbased-authentication for SSHv2 server. Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1412
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1413
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL ip ssh pub-key-file Specify the file used for host-based authentication. Syntax Parameters Defaults ip ssh pub-key-file {WORD} WORD Enter the file name for the host-based authentication.
PAGE 1414
poclab4,123.12.1.123 ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAox/ QQp8xYhzOxn07yh4VGPAoUfgKoieTHO9G4sNV+ui+DWEc3cgYAcU5Lai1MU2ODrzhCwyDNp05tK BU3t ReG1o8AxLi6+S4hyEMqHzkzBFNVqHzpQc+Rs4p2urzV0F4pRKnaXdHf3Lk4D460HZRhhVrxqeNx PDpEn WIMPJi0ds= ashwani@poclab4 NOTE: For rhostfile and pub-key-file, the administrator must FTP the file to the chassis.
PAGE 1415
Usage Information This command specifies the rhost file used for host-based authentication. This creates/ file overwrites the flash:/ADMIN_DIR/ssh/shosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command once. This file contains hostnames and usernames, for which hosts and users, rhost-authentication can be allowed.
PAGE 1416
ip ssh server Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. ip ssh server {ciphers cipher-list} {enable | port port-number} [kex keyexchange-algorithm] [mac hmac-algorithm][version 2] To disable SSH server functions, use the no ip ssh server {ciphers cipher-list} {enable | port port-number} [kex key-exchange-algorithm] [mac hmac-algorithm] command.
PAGE 1417
kex key-exchangealgorithm Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server. The following key exchange algorithms are available: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 When FIPS is enabled, the default key-exchange-algorithm is diffie-hellmangroup14-sha1.
PAGE 1418
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22.
PAGE 1419
Defaults vrf management Enter the keyword vrf followed by the keyword management to configure an SSH server on a management VRF. vrf vrf-name Enter the keyword vrf followed by the VRF name to configure an SSH server on that VRF. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1420
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information. ● For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/slot/port/subport information. ● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 1421
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1422
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command is useful if the remote SSH client implements Strict Host Key Checking.
PAGE 1423
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default.
PAGE 1424
Usage Information Example Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash://ADMIN_DIRssh/knownhosts file.
PAGE 1425
Usage Information Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash:/ADMIN_DIR/ssh/authorizedkeys.username file.
PAGE 1426
-c encryption cipher Enable the “FIPS mode enable", this mode will support the v2 client. "no fips mode enable"(disable) will support v1 & v2 client. This comment is applicable for both ciphers & HMAC algorithms: ● 3des-cbc: Force ssh to use 3des-cbc encryption cipher.
PAGE 1427
Version Description ● ● ● ● ● ● Usage Information Example aes256-cbc aes128-ctr aes192-ctr aes256-ctr hmac-sha2-256 hmac-sha2-256-96 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Added support for the -c and -m parameters on the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Added IPv6 support.
PAGE 1428
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1429
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1430
Parameters Defaults mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected.
PAGE 1431
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1432
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable IP source guard. Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1433
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1434
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ● clear ip dhcp snooping — clear the contents of the DHCP binding table. Role-Based Access Control Commands With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role.
PAGE 1435
Usage Information By default, access to commands are determined by the user’s role (if defined) or by the user’s privilege level. If the aaa authorization role-only command is enabled, then only the user’s role is used. Before you enable role-based only AAA authorization: 1. Locally define a system administrator user role.This will give you access to login with full permissions even if network connectivity to remote authentication servers is not available. 2. Configure login authentication on the console.
PAGE 1436
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL. ● userrole — creates user roles. show role Display information on permissions assigned to a command, including user role and/or permission level.
PAGE 1437
DellEMC# show role mode configure management route Role access: netadmin, sysadmin DellEMC# show role mode configure management crypto-policy Role access: secadmin, sysadmin Related Commands ● userrole — create user roles. show userroles Display information on all defined user roles.
PAGE 1438
Related Commands ● userrole — create user roles. userrole Create user roles for the role-based security model. Syntax userrole name inherit existing-role-name To delete a role name, use the no userrole name command. Note that the reserved role names may not be deleted. Parameters name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1439
NOTE: If you inherit a user role, you cannot modify or delete the inheritance. If you want to change or remove the inheritance, delete the user role and create it again. If the user role is in use, you cannot delete the user role. role mode { { { addrole | deleterole } role-name } | reset } command – Modifies (adds or deletes) command permissions for newly created user roles and system defined roles.
PAGE 1440
Table 7.
PAGE 1441
System Security Commands The following section lists the system security commands. generate hash Generate a hash checksum for the given file or the startup configuration using the MD5, SHA1, or SHA256 algorithm. Syntax Parameters Defaults generate hash {md5 | sha1 | sha256} {flash://filename | startup-config} md5 | sha1 | sha256 Enter the keyword md5, sha1, or sha256 to generate .
PAGE 1442
Command History Usage Information Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM. If you configure the secure-cli command on the system, the Dell EMC Networking OS resets any previously-configured root access password to the default root password without displaying any warning message.
PAGE 1443
verified boot hash Verify and store the hash value of the startup configuration. Syntax Parameters Defaults verified boot hash {system-image {A: | B:} | startup-config} hash value system-image {A: Enter the keyword system-image and A: or B:, depending on where the image | B:} is stored and then the hash value that is present on the iSupport page for your image. startup-config Enter the keyword startup-config and then the hash value for the startup configuration.
PAGE 1444
48 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1445
● For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID.
PAGE 1446
Defaults none Command Modes CONF-IF-VLAN Command History Example Related Command This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1447
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.
PAGE 1448
Usage Information Version Description 7.4.1.0 Introduced Dell EMC Networking OS must have the default CAM profile with the default microcode before you enable L2PT. protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters Defaults rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. 75 frames per second.
PAGE 1449
Related Commands ● show protocol-tunnel — displays tunneling information for all VLANs. ● show running-config — displays the current configuration. show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax Parameters Defaults show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094.
PAGE 1450
49 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1451
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6address} agent-addr {ipv4-address | ipv6-address} [number [max-datagramsize number]] | [max-datagram-size number] [vrf management] command.
PAGE 1452
Usage Information Version Description 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
PAGE 1453
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
PAGE 1454
sflow extended-switch enable Enable packing information on a switch only. Syntax sflow extended-switch enable To disable packing information, use the no sflow extended-switch [enable] command. Parameters Defaults enable Enter the keyword enable to enable global extended information. Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1455
Parameters Defaults extended Enter the keyword extended to copy 256 bytes from the sample packets to sFlow datagram. 128 bytes Command Modes CONFIGURATION INTERFACE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1456
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1457
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This command sets the counter polling interval for an interface. Related Commands ● sflow polling-interval (Global) — globally sets the polling interval. sflow sample-rate (Global) Change the global default sampling rate.
PAGE 1458
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This command changes the global default sampling rate. You can configure an interface to use a different sampling rate than the global sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power of 2 value.
PAGE 1459
Usage Information This command changes the sampling rate for an interface. By default, the sampling rate of an interface is set to the same value as the current global default sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power-of-2 value. Select one of these two number and re-enter the command. Related Commands ● sflow sample-rate (Global) — changes the sampling rate globally.
PAGE 1460
Usage Information Example Version Description 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The dropEvent counter (sFlow samples dropped due to sub-sampling) shown in the following example always displays a value of zero.
PAGE 1461
50 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1462
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1463
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 1464
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
PAGE 1465
RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1466
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1467
snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1468
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
PAGE 1469
The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB. If a community string is configured without a security-name (for example, snmp-server community public ro), the community is mapped to a default security-name/group: ● v1v2creadu / v1v2creadg — maps to a community with ro (read-only) permissions. ● v1v2cwriteu/ v1v2cwriteg — maps to a community with rw (read-write) permissions. The community-name parameter indexes this command.
PAGE 1470
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps.
PAGE 1471
● ● ● ● Defaults linkdown linkup syslog-reachable syslog-unreachable Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1472
snmp-server engineID Configure the name for both the local and remote SNMP engines on the router. Syntax snmp-server engineID [local engineID] [remote ip-address vrf vrf-name udpport port-number engineID] To return to the default, use the no snmp-server engineID [local engineID] [remote ip-address vrf vrf-name udp-port port-number engineID] command. Parameters local engineID Enter the keyword local followed by the engine ID number that identifies the copy of the SNMP on the local device.
PAGE 1473
Usage Information Changing the value of the SNMP Engine ID has important side effects. A user’s password (entered on the command line) is converted to a message digest algorithm (MD5) or secure hash algorithm (SHA) security digest. This digest is based on both the password and the local Engine ID. The command line password is then destroyed, as required by RFC 2274.
PAGE 1474
access-list-name (Optional) Enter both an IPv4 and IPv6 access list name. ipv6 access-listname Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 1475
To remove the SNMP host, use the no snmp-server host ip-address [vrf vrf-name] traps | informs [version 1 | 2c | 3] [auth | noauth | priv] [communitystring] [udp-port number] [notification-type] command. Parameters ip-address Enter the keyword host then the IP address of the host (configurable hosts is limited to 16). ipv6-address Enter the keyword host then the IPv6 address of the host in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1476
● ● ● ● ● ● ● isis — Enable ISIS adjacency change traps. pfc — Enable pfc traps. snmp — Enable SNMP trap. stp — Enable 802.1d state change traps. vlt — Enable VLT traps. vrrp — Enable VRRP state change traps. xstp — Enable 802.1s, 802.1w, and PVST+ state change traps. The default is all trap types are sent to host. Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1477
The snmp-server host command is used with the snmp-server enable command. Use the snmp-server enable command to specify which SNMP notifications are sent globally. For a host to receive most notifications, at least one snmp-server enable command and the snmp-server host command for that host must be enabled.
PAGE 1478
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server packetsize Set the largest SNMP packet size permitted. Wen the SNMP server is receiving a request or generating a reply, use the snmp-server packetsize global configuration command. Syntax snmp-server packetsize byte-count Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32.
PAGE 1479
Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1480
snmp-server user Configure a new user to an SNMP group.
PAGE 1481
priv password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the host to encrypt the contents of the message it sends to the agent. Minimum: eight characters long. access access- list-name (Optional) Enter the standard IPv4 access list name (a string up to 16 characters long). ipv6 access-listname (Optional) Enter the keyword ipv6 then the IPv6 access list name (a string up to 16 characters long).
PAGE 1482
Example Usage Information Example Usage Information Example Related Commands DellEMC# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv des56 d0452401a8c3ce42804fe80e3ba8763d The following command is an example of how to enter a plain-text password as the string authpasswd for user authuser of group v3group.
PAGE 1483
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.
PAGE 1484
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1485
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information Use this command to bind an SNMP agent to a VRF. The SNMP agent processes the requests from the interfaces that belong to the specified VRF. If no VRF is specified, then the default VRF is used.
PAGE 1486
Syslog Commands The following commands allow you to configure logging functions on all Dell EMC Networking switches. clear logging Clear the messages in the logging buffer. Syntax clear logging Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1487
Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the FN IOM. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the MXL.
PAGE 1488
Related Commands ● logging buffered — set the logging buffered parameters. default logging console Return the default settings for messages logged to the console. Syntax default logging console Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1489
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1490
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging trap — limit messages logged to the Syslog servers based on severity. logging Configure an IP address or host name of a Syslog server where logging messages are sent. Multiple logging servers of both IPv4 and/or IPv6 can be configured.
PAGE 1491
Version Description 9.5(0.0) Added udp and tcp keywords for the S4810, S4820T, S6000, Z9000, and MXL. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for IPv6. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1492
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.
PAGE 1493
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1494
● The system administrator and system security administrator roles can view security events and system events. ● The system administrator role can view audit, security, and system events. ● The network administrator and network operator roles can view system events. Examples Related Commands DellEMC(conf)#logging extended ● show logging auditlog — display the audit log. ● clear logging auditlog— clear the audit log.
PAGE 1495
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1496
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1497
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When the number of messages reach the limit you set with the logging history size command, older messages are deleted as newer ones are added to the table. Related Commands ● show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications.
PAGE 1498
Related Commands ● default logging monitor — returns the logging monitor parameters to the default setting. logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines. Syntax logging on To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1499
To disable this command and return to the default setting, use the no logging source-interface command. Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1500
Usage Information Syslog messages contain the IP address of the interface used to egress the router. By configuring the logging source-interface command, the Syslog packets contain the IP address of the interface configured. Related Commands ● logging — enables logging to the Syslog server. logging synchronous Synchronize unsolicited messages and Dell EMC Networking OS output.
PAGE 1501
Usage Information When you enable logging synchronous, unsolicited messages appear between software prompts and outputs. Only the messages with a severity at or below the set level are sent to the console. If the message queue limit is reached on a terminal line and messages are discarded, a system message appears on that terminal line. Messages may continue to appear on other terminal lines. Related Commands ● logging on — enables logging.
PAGE 1502
logging version Displays syslog messages in a RFC 3164 or RFC 5424 format. Syntax logging version {0|1} Defaults 0 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1503
Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. DellEMC(conf)# show logging auditlog ● clear logging auditlog — clear the audit log. show logging Display the logging settings and system messages logged to the internal buffer of the switch.
PAGE 1504
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1505
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1506
terminal monitor Configure the Dell EMC Networking OS to display messages on the monitor/terminal. Syntax terminal monitor To return to default settings, use the terminal no monitor command. defaults Disabled. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1507
51 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 8. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1508
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
PAGE 1509
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
PAGE 1510
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
PAGE 1511
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1512
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
PAGE 1513
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
PAGE 1514
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
PAGE 1515
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
PAGE 1516
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1517
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
PAGE 1518
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
PAGE 1519
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE 1.0.8802.1.1.2.1.5.47 lldpXMedTopology 95.0.1 ChangeDetected lldp-ext-med.
PAGE 1520
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generates an event that is configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
PAGE 1521
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation conflict resolved during audit 113 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
PAGE 1522
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
PAGE 1523
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1. Above threshold" 133 TR_VLT_DOMAIN _CFG_ERROR 134 1.3.6.1.4.1.6027.3.17 dellNetVLTDomain .2.0.6 ConfigError DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.
PAGE 1524
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls. An agent should not generate more than one entConfigChange 'notification-event' in a given time interval (five seconds is the suggested default). A 'notification-event' is the transmission of a single trap or inform PDU to a list of notification destinations.
PAGE 1525
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.23 dellNetSysAlarmCa DELLrdVersionMismatch NETWORKINGCHASSIS-MIB.
PAGE 1526
Table 8. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
PAGE 1527
52 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1528
• • • storm-control multicast (Interface) storm-control unknown-unicast (Configuration) storm-control unknown-unicast (Interface) polling-interval You can set the time interval to poll the queue depth and egress counters. Syntax polling—interval {interval in milli-seconds} Parameters Defaults interval in milliseconds Enter the polling interval in milliseconds. The range is 200 to 1000. The interval should be entered in multiples of 100. The default interval value is 100 milliseconds.
PAGE 1529
of polling-intervals, then it would be detected as PFC storm condition. The ‘xoff’ state means no transmission of data happens out of a port/queue even though there are packets buffered in that queue. Example Use the storm-control pfc command in the configuration mode to enter the ‘storm-control-pfc' configuration mode. The commands provisioned in this mode are applicable for all the interfaces that have PFC storm enabled.
PAGE 1530
Usage Information The storm-control pfc in queue-drop command is used to drop the traffic meant for egressing through the specified port or priority where PFC storm has been detected. Example DellEMC(conf-if-te-1/24)# storm-control pfc in queue-drop queue-drop backoff-force You can remove the queue-drop state after the specified number of polling is done.
PAGE 1531
Usage Information The queue-drop backoff-on-norxpfc polling-count command is used to remove the queuedrop state if additional PFCs are not received for the specified number of polling intervals. Example Use the storm-control pfc command in the configuration mode to enter the ‘storm-control-pfc' configuration mode. The commands provisioned in this mode are applicable for all the interfaces that have PFC storm enabled.
PAGE 1532
Example DellEMC#show storm-control pfc status stack-unit 1 port-set 0 ------------------------------------------------------------------------------------------------------Interface Priority State Duration in discard state(in ms) Pkts Dropped(Ingress) Pkts Dropped(Egress) Pkts Dropped(Ingress,Cumulative) Pkts Dropped(Egress,Cumulative)---------------------------------------------------------------------------------------Te 1/1/1 4 Drop 1194740 2389 135759218588 2389 135759218588 Te 1/1/1 0 4 Normal 0 0
PAGE 1533
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6000, S6000–ON, S6100–ON, Z9100–ON. The show storm-control pfc statistics command is used to view the statistical data of the PFC storm on the specified stack unit and the port set.
PAGE 1534
Related Commands show storm-control pfc statistics — used to view the statistical data of the PFC storm on the specified stack unit and the port set. show storm-control broadcast Display the storm control broadcast configuration.
PAGE 1535
show storm-control multicast Display the storm control multicast configuration. Syntax Parameters Defaults show storm-control multicast [interface] interface (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1536
DellEMC# show storm-control unknown-unicast Display the storm control unknown-unicast configuration. Syntax show storm-control unknown-unicast [interface] Parameters Defaults interface (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1537
Version Description 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. storm-control broadcast (Configuration) Configure the percentage of broadcast traffic allowed in the network. Syntax storm-control broadcast [packets_per_second in] To disable broadcast rate-limiting, use the no storm-control broadcast [packets_per_second in] command.
PAGE 1538
Usage Information Version Description 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series. Broadcast storm control is valid on Layer 2/Layer 3 interfaces only. Layer 2 broadcast traffic is treated as unknown-unicast traffic. storm-control broadcast (Interface) Configure the percentage of broadcast traffic allowed on an interface (ingress only).
PAGE 1539
storm-control multicast (Configuration) Configure the packets per second (pps) of multicast traffic allowed into the C-Series and S-Series networks only. Syntax storm-control multicast packets_per_second in To disable storm-control for multicast traffic into the network, use the no storm-control multicast packets_per_second in command. Parameters Defaults packets_per_sec ond in Enter the packets per second of multicast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1540
Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1541
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series. Unknown Unicast Storm-Control is valid for Layer 2 and Layer 2/Layer 3 interfaces.
PAGE 1542
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
PAGE 1543
53 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1544
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1545
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
PAGE 1546
Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1547
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree — enter SPANNING TREE mode on the switch.
PAGE 1548
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● max-age — changes the wait time before STP refreshes protocol configuration information. ● hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1549
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults seconds Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1550
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1551
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1552
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1553
Example Field Description “Port path...” Displays the path cost, priority, and identifier for the interface. “Designated root...” Displays the priority and MAC address of the root bridge of the STG that the interface belongs. “Designated port...” Displays the designated port ID. DellEMC# show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.
PAGE 1554
Te 1/1/3/1 8.28 DellEMC# Usage Information Example (Guard) 8 4 FWD 0 32768 0001.e800.0a56 8.28 The following describes the show spanning-tree 0 guard command shown in the example. Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1555
Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1556
54 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1557
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1558
Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1559
support-assist activity Trigger an activity event immediately. Syntax Parameters support-assist activity {full-transfer | core-transfer} start now full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information. core-transfer Enter the keyword core-transfer to specify transfer of core files. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1560
Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. Introduced the core-transfer and event-transfer parameters. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. By default, each activity follows a set of default actions using a default schedule.
PAGE 1561
Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes. last-name Enter the last name for the contact person. To include a space, enter a space within double quotes. Command Modes SUPPORTASSIST Command History Usage Information This guide is platform-specific.
PAGE 1562
server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode. Syntax server {default | server-name} To delete a server, use the no server server-name command. Parameters Defaults default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred. To include a space, enter a space within double quotes. Default server has URL stor.g3.ph.dell.
PAGE 1563
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
PAGE 1564
Related Commands ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest show — view the list of action-manifest for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. action-manifest remove Remove the action-manifest file from Dell EMC Networking OS. Syntax action-manifest remove } Parameters local-file-name Enter the name of the local action-manifest file.
PAGE 1565
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest install — configure the action-manifest to use for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. enable Enable a specific SupportAssist activity.
PAGE 1566
To remove the complete company contact information, use the no address command. Parameters city company- city province | region | state name (OPTIONAL) Enter the keyword city then the city or town for the company site. To include a space, enter a space within double quotes. (OPTIONAL) Enter the keyword province, region or state then the name of province, region or state for the company site. To include a space, enter a space within double quotes.
PAGE 1567
Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. territory Configure the territory and set the coverage for the company site.
PAGE 1568
Parameters primary email- address alternate emailaddress Enter the keyword primary then the primary email address for the person. Enter the keyword alternate then the alternate email address for the person. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM.
PAGE 1569
Related Commands ● preferred-method — configure the preferred method for contacting the person. preferred-method Configure the preferred method for contacting the person. Syntax Parameters Defaults preferred-method {email | no-contact | phone] email Enter the keyword email to specify email as preferred method. no-contact Enter the keywords no-contact to specify that there is no preferred method. phone Enter the keyword phone to specify phone as preferred method.
PAGE 1570
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. SupportAssist Server Commands Dell EMC Networking OS supports the following SupportAssist Server mode commands. proxy-ip-address Configure a proxy for reaching the SupportAssist remote server.
PAGE 1571
Usage Information The passwords are stored encrypted in the running configuration. enable Enable communication with the SupportAssist server. Syntax enable To disable communication to a specific SupportAssist server, use the no enable command. Defaults Enabled Command Modes SUPPORTASSIST SERVER Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1572
Usage Information The URL should be formatted to follow the ISO format. show eula-consent Display the EULA for the feature. Syntax show eula-consent {support-assist | other feature} Parameters support-assist | other feature Enter the keywords support-assist or the text corresponding to other feature. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1573
allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dells affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
PAGE 1574
preferred-method email time-zone zone +05:30 start-time 12:23 end-time 15:23 ! server Dell enable url http://1.1.1.1:1332 DellEMC# show support-assist status Display information on SupportAssist feature status including any activities, status of communication, last time communication sent, and so on. Syntax show support-assist status Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1575
55 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1576
Defaults end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year.
PAGE 1577
Defaults start-week (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: ● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month. ● last: Enter this keyword to start daylight saving time in the last week of the month.
PAGE 1578
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key. ● clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. ● show clock — displays the current clock settings.
PAGE 1579
Usage Information Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8. debug ntp Display Network Time Protocol (NTP) transactions and protocol messages for troubleshooting.
PAGE 1580
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp broadcast client Set up the interface to receive NTP broadcasts from an NTP server.
PAGE 1581
ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option. Syntax ntp control-key-passwd [encryption-type] password To delete the control key, use the no ntp control-key-passwd [encryption-type] password command. Parameters Defaults encryption-type (OPTIONAL) Enter one of the following numbers: ● 0 (zero) directs the system to store the password as clear text. It is the default encryption type when using the password option.
PAGE 1582
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp master Configure the switch as NTP Server. Syntax ntp master Parameters Defaults ntp Enter the stratum number to identify the NTP Server's hierarchy.
PAGE 1583
Defaults Zero (0). Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3038–ON, S4048-ON, S3100 Series, S4810P, S4820T, S5000, S6000, S6000–ON, S6100–ON, Z9500, and Z9100–ON.
PAGE 1584
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added support for VRF. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added IPv6 support. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1585
Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/slot/port[/subport] information.
PAGE 1586
ntp step-threshold Configure the step-threshold time interval. Syntax ntp step-threshold value To return to the default NTP step-threshold value, use the no ntp step-threshold command. Parameters Defaults value Enter the threshold value in milliseconds. The range is from 128 to 5000 milliseconds (5 seconds). 128 milliseconds Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 1587
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The number parameter in the ntp trusted-key command must be the same number as the number parameter in the ntp authentication-key command.
PAGE 1588
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1589
Example Example (Detail) Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC#show clock 11:05:56.949 UTC Thu Oct 25 2001 DellEMC# DellEMC# show clock detail 12:18:10.
PAGE 1590
Usage Information Example (without ntp master configuration) Example (with ntp master configuration) Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp associations command shown in the Example below. Field Description (none) One or more of the following symbols could be displayed: ● * means synchronized to this peer. ● # means almost synchronized to this peer.
PAGE 1591
Related Commands ● show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXECEXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1592
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1593
56 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1594
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface.
PAGE 1595
description Enter a text description of an uplink-state group. Syntax Parameters Defaults description text text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.
PAGE 1596
Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1597
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. ● downstream — assign a port or port-channel to the uplink-state group as a downstream interface.
PAGE 1598
Related Commands ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. ● uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. enable Enable uplink state group tracking for a specific UFD group. Syntax enable To disable upstream-link tracking without deleting the uplink-state group, use the no enable command. Defaults Upstream-link tracking is automatically enabled in an uplink-state group.
PAGE 1599
Version Description 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1600
Related Commands ● show running-config uplink-state-group — displays the current configuration of one or more uplinkstate groups. ● uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. uplink-state-group Create an uplink-state group and enable the tracking of upstream links on a switch or router. Syntax uplink-state-group group-id To delete an uplink-state group, enter the no uplink-state-group group-id command.
PAGE 1601
upstream Assign a port or port-channel to the uplink-state group as an upstream interface. Syntax upstream interface To delete an uplink-state group, use the no upstream interface command.
PAGE 1602
57 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1603
Usage Information The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
PAGE 1604
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
PAGE 1605
Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1606
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000.
PAGE 1607
tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit value To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters Defaults value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64.
PAGE 1608
Defaults Tunnel keepalive is disabled. Command Modes INTERFACE TUNNEL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1609
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. To enable a tunnel interface, use this command.
PAGE 1610
Command History Usage Information 1610 Tunneling This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1611
58 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1612
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. When packets are colored green; no packets are dropped.
PAGE 1613
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. Syntax Parameters Defaults dei mark {green | yellow} {0 | 1} 0|1 Enter the bit value you want to map to a color. green | red | yellow Choose a color: ● Green: High priority packets that are the least preferred to be dropped.
PAGE 1614
To remove an interface from a Stackable VLAN, use the no member interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a Port Channel interface, enter the keywords port-channel, and then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. ● For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1615
Parameters stack-unit number Enter a stack member identifier of the switch that you want to add to the stack. module slot number Enter the slot number of the module to identify the slot to be provisioned. module type Enter the module type from one of the following: ● QSFP+ ● QSFP28 ● QSFP28_4CXP Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1616
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to enabling this command, to place the interface in Layer 2 mode, enter the switchport command.
PAGE 1617
Version Description E-Series original Command Usage Information Prior to disabling the stackable VLAN feature, remove the members. To view the stackable VLANs, use the show vlan command in EXEC Privilege mode. Stackable VLANs contain members, designated by the M in the Q column of the command output. If you enabled VRF, you cannot enable the stacked VLAN feature using this command. If you enabled IGMP snooping, you cannot enable the stacked VLAN feature using this command.
PAGE 1618
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. You can separate the C-Tag values by commas or dashed ranges. In the case of conflicts, dynamic mode CoS overrides any Layer 2 QoS configuration.
PAGE 1619
Usage Information For specific interoperability limitations regarding the S-Tag TPID, see the Dell EMC Networking OS Configuration Guide. The four characters you may enter are shown in the following table. Related Commands Number Resulting TPID 1 0x0001 10 0x0010 81 0x0081 8100 0x8100 ● portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays.
PAGE 1620
Version Description E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, use the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. In Example 1, a VLAN-Stack trunk port is configured and then made part of a single-tagged VLAN. In Example 2, the tag protocol identifier (TPID) is set to 88A8.
PAGE 1621
DellEMC(conf-if-te-1/1/3/1)# vlan-stack trunk DellEMC(conf-if-te-1/1/3/1)# exit DellEMC(config)# interface vlan 10 DellEMC(conf-if-vlan)# vlan-stack compatible DellEMC(conf-if-vlan)# member Te 1/1/4/1, Te 1/1/4/2, TenGi 1/1/4/3 DellEMC(conf-if-vlan)# exit DellEMC(config)# interface vlan 30 DellEMC(conf-if-vlan)# untagged TenGi 1/1/4/2 DellEMC(conf-if-vlan)# exit DellEMC(config)# DellEMC(config)# interface vlan 40 DellEMC(conf-if-vlan)# tagged TenGi 1/1/4/2 DellEMC(conf-if-vlan)# exit DellEMC(config)# VLAN
PAGE 1622
59 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • • ip unknown-unicast ipv6 unknown-unicast description ip vrf forwarding ip http vrf ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip unknown-unicast Enable IPv4 catch-all route.
PAGE 1623
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv6 unknown-unicast Disable soft forwarding of unknown IPv6 destination packets.
PAGE 1624
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
PAGE 1625
You can configure an IP subnet or address on a physical or VLAN interface that overlaps the same IP subnet or address configured on another interface only if the interfaces are assigned to different VRFs. If you assign two interfaces to the same VRF, you cannot configure overlapping IP subnets or the same IP address to them.
PAGE 1626
Usage Information Version Description 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To make the HTTP clients VRF-aware, use the ip http vrf command. The HTTP client uses the VRF name that you specify to reach the HTTP server. If you do not specify a VRF name, the HTTP client uses the default VRF. ip route-export Enables route leaking between VRFs. This command exports or shares IPv4 routes corresponding to one VRF with other nondefault VRFs.
PAGE 1627
Related Commands ● ip route-import — imports routes from another VRF. ip route-import Imports IPv4 routes that another VRF leaks using the VRF tag during the export of these routes. Syntax Parameters ip route-import tag [route-map—name] route-import Enter the keywords route-import to import routes into the VRF. tag Enter a tag (ASN number) to specify an import route target for importing routes from another VRF.
PAGE 1628
Defaults tag Enter a tag (ASN number) as the export route target to expose routes to other VRFs. This tag acts as an identifier for exported routes. Use this identifier while importing these routes into another nondefault VRF. route-map-name (Optional) Enter the name of the route-map to filter the exported routes. You can leak global routes to be made available to VRFs.
PAGE 1629
route-map-name Defaults Enter the name of the route-map to filter the imported routes. NOTE: Use the route-map attribute while importing routes from the global RTM. Route-maps allow you to filter routes at the import end based on the matching criteria that you define in the route-map. N/A Command Modes ● VRF mode ● CONFIGURATION mode Command History Usage Information Related Commands This guide is platform-specific.
PAGE 1630
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. Specify the matching criteria only after defining a route-map. Before using this command, you must enter Route Map mode using the route-map route-map-name command.
PAGE 1631
interface management Associates a management port with a management VRF. Syntax interface management To delete the association between a management port and a management VRF, use the no interface management command. Command Modes VRF MODE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1632
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1633
show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax Parameters show run vrf vrf-name vrf vrf-name Enter the keyword vrf and then the name of the VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1634
60 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1635
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1636
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1637
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link. You can also configure the VLANs you want to exclude from the VLT proxy gateway.
PAGE 1638
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1639
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The proxy-gateway feature may go operationally down for any of the following reasons: ● ● ● ● LLDP is globally disabled.
PAGE 1640
61 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1641
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax Parameters Defaults back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1642
clear vlt statistics Clear the VLT operation statistics. Syntax clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP.
PAGE 1643
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax Parameters Defaults delay-restore delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1644
This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap). Defaults 60 seconds Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1645
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. LACP on the VLT ports (on a VLT switch or access device), which are members of the VLT, are not brought up until the VLT domain is recognized on the access device.
PAGE 1646
Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1647
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan option. 8.3.8.0 Introduced on the S4810. To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option.
PAGE 1648
peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 65535. The default value is infinity. Command Modes VLT DOMAIN (conf-vlt-domain) Default Infinity Command History This guide is platform-specific.
PAGE 1649
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1650
Usage Information Example (Brief) Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell EMC Networking OS version number. VLT version numbers begin with odd numbers.
PAGE 1651
Example Version Description 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays counter information.
PAGE 1652
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) If you do not add a parameter such as arp or mac, the output displays all the counters.
PAGE 1653
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1654
-----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.2) VLAN 15 DellEMC# --------VLAN 6 te 1/1/1/1 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show mismatch in VXLAN instance parameters. 9.10(0.
PAGE 1655
VLAN to VNI config mismatch -------------------------------------Vlan-ID Local VNID Peer VNID -----------------------------10 10 11 11 12 12 13 13 - VXLAN enabled status on VLT Port Channels ------------------------------------------Local-Lag Status Peer-Lag Status -----------------------------300 Disable 100 Disable 700 Enable 812 Disable 999 Disable 888 Disable Local VTEP IP mismatch ------------------------------------------------------------------Local Node “Local VTEP IP” Remote Node “Local VTEP IP”
PAGE 1656
Local Lag --------128 Peer Lag Local VLANs -------- ----------128 4094 Peer VLANs ---------100 DellEMC# show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific.
PAGE 1657
show vlt statistics Displays VLT operations statistics. Syntax Parameters Default show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] arp Enter the keyword arp to display the ARP VLT statistics. domain Enter the keyword domain to display the domain VLT statistics. igmp-snoop Enter the keywords igmp-snoop to display the IGMP snooping VLT statistics. mac Enter the keyword mac to display the VLT MAC addresses VLT statistics.
PAGE 1658
VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg Response rcvd: 1 IGMP PDU Tunnel Pkt sent: 5 IGMP PDU Tunnel Pkt rcvd: 10 IGMP Tunnel PDUs sent: 10 IGMP Tun
PAGE 1659
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1660
Usage Information Version Description 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, the Dell EMC Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for internal system operations. To explicitly configure the unit ID of a VLT peer, use the unit-id command. Configure a different unit ID (0 or 1) on each peer switch.
PAGE 1661
Parameters Defaults id-number Enter the respective VLT port-channel number of the peer device. Not configured. Command Modes INTERFACE PORT-CHANNEL Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1662
62 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
PAGE 1663
Usage Information Use this command to clear the remote VTEP and access port statistics. clear mac-address-table dynamic Clear the MAC address table of specific or all MAC address learned dynamically.
PAGE 1664
Defaults Disabled Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1665
Usage Information Version Description 9.14(2.3) Introduced on the S4048–ON, S4048T-ON, S6000, S6010-ON, S6100-ON, and Z9100–ON. Use the disable-mac-learn command in the VXLAN-INSTANCE mode. NOTE: ● This command is only applicable for static VXLAN and does not work for the other modes of VXLAN (controller and nuage). ● The remote VTEP should already be configured. ● In case of static VXLAN VLT deployments, this configuration should be symmetric across VLT nodes.
PAGE 1666
Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1667
Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. Use the local-vtep-ip IP Address command to set the local IP Address that would be used as source for VXLAN tunnels. max_backoff Configures time to wait between connection attempts with controller.
PAGE 1668
Version Description 9.14(0.0) Introduced on the S6000, S6000–ON, S6010-ON, S4048-ON, S4048T-ON, S5048F-ON, S6100-ON, and Z9100-ON. remote-vtep-ip Create a remote VTEP and associate it to specified VNIDs. Syntax remote—vtep—ip IP Address vni-profile profile name To delete the remote VTEP, use the no remote—vtep—ip command. Parameters Defaults IP Address Enter the IP Address of the remote VTEP.
PAGE 1669
vni-profile Create a VNI profile to associate with remote VTEP configuration. Syntax vni—profile profile name To delete the VNI profile, use the no vni-profile command. Parameters Defaults profile name Enter a valid and unique profile name. The profile name can have a maximum of 32 characters. None Command Modes VXLAN-INSTANCE Command History Usage Information This guide is platform-specific.
PAGE 1670
Version Description 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. Usage Information You must configure VXLAN globally before using VXLAN-instance. Use the no shutdown command to enable the VXLAN instance.
PAGE 1671
vxlan-instance loopback Provision VXLAN and non-VXLAN loopback ports that support routing in and out of VXLAN tunnels and enable MAC level loopback on all these ports. Syntax Parameters Defaults vxlan-instance instance ID loopback [port-channel id] instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1.
PAGE 1672
Defaults Controller mode. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. By default, VXLAN instance is created in controller mode. You need a controller to configure VTEP.
PAGE 1673
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.
PAGE 1674
Example Related Commands Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 Instance : 1 Admin State : enabled Management IP : 192.168.200.
PAGE 1675
Example DellEMC#show vxlan vxlan-instance 1 logical-network name LN-1 Name : LN-1 Description : Type : ELAN Tunnel Key : 1 VFI : 28674 Unknown Multicast MAC Tunnels: 2.2.2.
PAGE 1676
Example Related Commands DellEMC#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) vxlan-instance — Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics interface Displays the port VLAN statistics information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1677
Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics remote-vtep-ip Displays VXLAN statistics for a specific VXLAN tunnel. Syntax Parameters show vxlan vxlan-instance instance ID statistics remote-vtep-ip IP Address instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. remote-vtep-ip Enter the keyword remote-vtep-ip followed by the IP Address of the remote VTEP.
PAGE 1678
Version Description 9.13(0.0) Updated to show VLT peer’s local macs. 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. Introduced on the Z9100–ON. Example Related Commands 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1679
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S6000. DellEMC#show vxlan vxlan-instance 1 unicast-mac-remote Total Remote Mac Count: 1 VNI MAC TUNNEL 100 00:00:07:00:02:00 (N) 60.1.1.1 vxlan-instance- Enable VXLAN Instance configuration on the platform.
PAGE 1680
63 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1681
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1682
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax clear counters vrrp [vrrp-id] [ipv6] Parameters vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1683
between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups.
PAGE 1684
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group.
PAGE 1685
disable Disable a VRRP group. Syntax disable To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1686
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1687
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process.
PAGE 1688
Usage Information To guarantee that a VRRP group becomes MASTER, configure the VRRP group’s virtual address with same IP address as the interface’s primary IP address and change the priority of the VRRP group to 255. If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration.
PAGE 1689
show vrrp View the VRRP groups that are active. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group. Syntax Parameters show vrrp [vrrp-id][brief][interface type][ipv6][interface type][vrf vrfname] vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups.
PAGE 1690
Usage Information Example (Brief) Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The following describes the show vrrp brief command. Item Description Interface Lists the interface type, slot, and port of the configured VRRP group. Grp Displays the VRRP group ID. Pri Displays the priority value assigned to the interface.
PAGE 1691
Item Description ● Adv sent displays the number of VRRP advertisements sent on the interface. ● Gratuitous ARP sent displays the number of gratuitous ARPs sent. Virtual MAC address Displays the virtual MAC address of the VRRP group. Virtual IP address Displays the virtual IP address of the interface’s VRRP router. Authentication:... States whether authentication is configured for the VRRP group. If it is configured, this lists the authentication type and password. Tracking states..
PAGE 1692
track Monitor an interface and lower the priority value of the VRRP group on that interface if it is disabled. Syntax track interface [priority-cost cost] To disable monitoring, use the no track interface command. Parameters Defaults interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1693
To delete one or more virtual IP addresses, use the no virtual-address ip-address1 [... ip-address12] command. Parameters Defaults ip-address1 Enter an IP address of the virtual router in dotted decimal format. The IP address must be on the same subnet as the interface’s primary IP address. ... ip-address12 (OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted decimal format. Separate the IP addresses with a space.
PAGE 1694
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.
PAGE 1695
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. This command applies to all the VRRP interfaces on a system. When you use this command with the vrrp delay minimum command, the later timer rules VRRP enabling. For example, if vrrp delay reload is 600 and vrrp delay minimum is 300: ● When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 1696
Related Command ● virtual-address — assigns up to 12 virtual IP addresses per VRRP group. version Set the VRRP protocol version for the IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters Defaults 2 Enter the keyword 2 to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the keyword 3 to specify VRRP version 3 as defined by RFC 5798, Virtual Router Redundancy Protocol.
PAGE 1697
IPv6 VRRP Commands The following are IPv6 VRRP commands. ● clear counters vrrp ipv6 ● debug vrrp ipv6 ● show vrrp ipv6 ● vrrp-ipv6-group The following commands apply to IPv4 and IPv6: ● advertise-interval ● description ● disable ● hold-time ● preempt ● priority ● show config ● virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups.
PAGE 1698
Usage Information NOTE: You can also clear the port configurations corresponding to a range of ports. For Open Networking (ON) platforms, the notation for specifying the port range in the command is different from how you specify the port range in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 1699
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series, C-Series, and S-Series. Support was added for IPv6 VRRP groups in nondefault VRF instances. 8.3.2.0 Introduced on the E-Series.
PAGE 1700
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.3.2.0 Introduced on the E-Series.
PAGE 1701
TenGigabitEthernet 1/1/2/1, IPv6 VRID: 255, Version: 3, Net: fe80::201:e8ff:fe7a:6bb9 VRF: 0 default-vrf State: Master, Priority: 101, Master: fe80::201:e8ff:fe7a:6bb9 (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 64 Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 1::255 fe80::255 vrrp-ipv6-group Assign an interface to a VRRP group.
PAGE 1702
NOTE: For all routers to interoperate, configure the same VRID on neighboring routers (Dell EMC Networking or non- Networking) in the same VRRP group. Related Commands 1702 ● virtual-address — assigns up to 12 virtual IP addresses per VRRP group.
PAGE 1703
64 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1704
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax crypto ca-cert install path Parameters Defaults path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1705
● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1706
email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect. For self-signed certificates, if validity is not specified, it defaults to 3650 days, or 10 years. length length (OPTIONAL) Enter the keyword length followed by a bit length value.
PAGE 1707
Parameters cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored. Following are example of a path that you can specify: flash://certs/s4810-001-request.crtand usbflash:/certs/s4810-001-cert.
PAGE 1708
If the system is in non-FIPS mode, the certificate will be installed as the non-FIPS certificate. When FIPS mode is enabled/disabled, the certificates (and keys) are switched by the system. Related Commands ● crypto ca-cert install crypto x509 ocsp Configures the OCSP behavior. Syntax crypto x509 ocsp [nonce] [sign-requests] Parameters Defaults nonce Enter the keyword nonce to use the nonce feature for the OCSP requests to OCSP responder communication.
PAGE 1709
Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Related Commands Version Description 9.11.0.0 Introduced this command.
PAGE 1710
tcp Enter the keyword tcp to enable TCP. udp Enter the keyword udp to enable UDP. vrf vrf-name Enter the keyword vrf followed by the name of the VRF. sha1 fingerprint Enter the keyword sha1 followed by the finger print. This option is only available when the secure option is configured. This new option enables the Syslog feature to compare the received certificate’s sha-1 fingerprint against this configured sha-1 fingerprint.
PAGE 1711
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin When you use this command, the device maps the current certificate context in the certificate store to a CA certificate through the subject key identifier field. The subject key identifier field contains the SHA-1 hash of the CA’s public key. This configuration provides a way to uniquely identify a CA and associate it with any CA-specific settings.
PAGE 1712
Related Commands ● crypto x509 ocsp ocsp-server prefer Configures OCSP responder preference. You can configure the preference or order that the CA or a device should follow while contacting multiple OCSP responders. Syntax ocsp-server prefer Defaults None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1713
show crypto cert Displays the certificate information that is specified. Syntax Parameters Defaults show crypto cert {path} path (OPTIONAL) Enter the path to a local file where a certificate chain is stored in PEM format. If a path is not specified, display the certificate that is currently installed on the system. None. Command Modes EXEC Privilege Command History This guide is platform-specific.