CLI Guide

Example (If
no ports are
configured within
the specified
interface range)
DellEMC(conf)# interface range gigbitethernet 1/1 - 1/11,
tengigabitethernet 3/3, gigbitethernet 3/10
% Error: No port is configured in interface range
Example
(Configuration
Terminal Batch
Mode)
DellEMC(conf-b)#interface range te 1/1-4
DellEMC(conf-if-range-te-1/1-4)#
Example
(Multiple Ports)
DellEMC(conf)# interface range gigabitethernet 2/10 - 2/23,
gigabitethernet 2/12 - 2/17
DellEMC(conf-if-range-gi-2/10-2/23)#
Example
(Overlapping
Ports)
DellEMC(conf)# interface range gigabitethernet 2/3 - 2/11,
gigabitethernet 2/3 - 2/23
DellEMC(conf-if-range-gi-2/3-2/23)#
Usage
Information
Only VLAN and port-channel interfaces created using the interface vlan and interface port-
channel commands can be used in the interface range command.
Use the show running-config command to display the VLAN and port-channel interfaces. VLAN
or port-channel interfaces that are not displayed in the show running-config command cannot be
used with the bulk configuration feature of the interface range command. You cannot create virtual
interfaces (VLAN, Port-channel) using the interface range command.
NOTE: If a range has VLAN, physical and port-channel interfaces, only commands related to physical
interfaces can be bulk configured. To configure commands specific to VLAN and port-channel only
those respective interfaces should be configured in a particular range.
Example (Single
Range)
This example shows a single range bulk configuration.
DellEMC(config)# interface range gigabitethernet 5/3 - 23
DellEMC(config-if-range-gi-5/3-5/23)# no shutdown
DellEMC(config-if-range-gi-5/3-5/23)#
Example
(Multiple Range)
This example shows how to use commas to add different interface types to a range of interfaces.
DellEMC(config-if)# interface range gigabitethernet 5/1 - 5/23,
gigabitethernet 1/1 - 1/2
DellEMC(config-if-range-gi-1/1-1/2,gi-5/1-5/23)# no shutdown
DellEMC(config-if-range-gi-1/1-1/2,gi-5/1-5/23)#
Example
(Multiple Range)
This example shows how to use commas to add VLAN and port-channel interfaces to the range.
DellEMC(config-if)# interface range gigabitethernet 5/1 - 5/23,
gigabitethernet 1/1 – 1/2,
Vlan 2–100, Port 1–25
DellEMC(config-if-range-gi-1/1-1/2,gi-5/1-5/23,vl-2-100,po-1-25)# no
shutdown
DellEMC(config-if-range)#
Example
(Batch Mode
Configuration)
Primary VLT
DellEMC(conf-b)#int range Tengigabitethernet 3/0 - 5
DellEMC(conf-if-range-te-3/0-5)#mtu 4500
DellEMC(conf-if-range-te-3/0-5)#exit
DellEMC(conf-b)#show conf
interface range tengigabitethernet 3/0 - 5
mtu 4500
DellEMC(conf-b)#commit
DellEMC(conf-b)#Dec 6 11:30:45 %RPM1-P:CP %CLIBATCH-6-
624 Interfaces