Concept Guide

Table 110. Interface level MIB Objects for Port Security (continued)
MIB Object OID Access or Permission Description
dellNetPortSecIfStationMove
Enable
1.3.6.1.4.1.6027.3.31.1.2.1.1.5 read-write Enable or disable station movement
on the dynamically secured MAC
addresses learnt on the interface.
dellNetPortSecIfSecureMacVi
olationAction
1.3.6.1.4.1.6027.3.31.1.2.1.1.6 read-write Determines the action to be taken
when MAC limit violation occurs in
the system.
dellNetPortSecIfStmvViolatio
nAction
1.3.6.1.4.1.6027.3.31.1.2.1.1.7 read-write Determines the action to be taken
when either dynamic or static MAC
limit violation occurs in the system.
dellNetPortSecIfStickyEnable 1.3.6.1.4.1.6027.3.31.1.2.1.1.8 read-write Enables or disables sticky port
security feature on this interface.
dellNetPortSecIfClearSecure
MacAddresses
1.3.6.1.4.1.6027.3.31.1.2.1.1.9 read-write Deletes secure MAC addresses
based on the specified type.
dellNetPortSecIfResetViolatio
nStatus
1.3.6.1.4.1.6027.3.31.1.2.1.1.10 read-write Resets the violation status of an
interface based on the specified
type.
dellNetPortSecIfSecureMacA
geEnable
1.3.6.1.4.1.6027.3.31.1.2.1.1.11 read-write Enables aging of the dynamically
secured MAC addresses learnt on
the interface.
Enabling and viewing SNMP for port security
To enable or view DELL-NETWORKING-PORT-SECURITY-MIB, configure snmp-server in read-write mode using the snmp-
server community public rw command. You can enable the port security feature on the Dell EMC Networking OS using
the snmpset command. Also, you can view if the port security feature is enabled or disabled using the snmpwalk command.
To configure dellNetPortSecIfSecureMacLimit as 100 on an interface whose ifIndex is 2101252, use the following
command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 100
To remove dellNetPortSecIfSecureMacLimit configuration on an interface whose ifIndex is 2101252, use the
following command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 2147483647
To retrieve dellNetPortSecIfSecureMacLimit configured on an interface whose ifIndex is 2101252, use the following
command.
snmpwalk -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252
SNMPv2-SMI::enterprises.6027.3.31.1.2.1.1.3. 2101252 = INTEGER: 10
MIB objects for configuring MAC addresses
This section describes about the MIB objects dellNetPortSecSecureStaticMacAddrTable to configure and un-
configure static MAC addresses in the system. The OID of this MIB table is 1.3.6.1.4.1.6027.3.31.1.2.2.
The table is indexed by the following parameters:
● MAC Address (Octet string of length 6 and MAC address ( in decimal) as value
● VLAN ID
● Interface Index
NOTE:
Simple Network Management Protocol (SNMP) 815