Install Guide

ManualsBrandsDell ManualsAccess PlatformsOS9

Table Of Contents

Dell EMC Command Line Reference Guide for

the S4048T–ON System

9.14.2.2

July 2019

Rev. A00

Summary of content (1744 pages)

PAGE 1
Dell EMC Command Line Reference Guide for the S4048T–ON System 9.14.2.2 July 2019 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: About this Guide......................................................................................................... 41 Objectives............................................................................................................................................................................ 41 Audience.............................................................................................................................................................................
PAGE 4
asf-mode............................................................................................................................................................................. 85 banner exec........................................................................................................................................................................ 86 banner login....................................................................................................................................
PAGE 5
show memory................................................................................................................................................................... 139 show processes cpu........................................................................................................................................................139 show processes ipc flow-control................................................................................................................................
PAGE 6
show ip accounting access-list............................................................................................................................... 191 show ip access-lists.................................................................................................................................................. 193 Standard IP ACL Commands........................................................................................................................................ 193 deny..........
PAGE 7
match metric.............................................................................................................................................................. 249 match origin................................................................................................................................................................250 match route-type.................................................................................................................................................
PAGE 8
permit (for Extended IP ACLs)....................................................................................................................................294 permit (for Standard MAC ACLs)...............................................................................................................................295 seq (for Standard MAC ACLs)....................................................................................................................................
PAGE 9
bgp always-compare-med.......................................................................................................................................348 bgp asnotation........................................................................................................................................................... 349 bgp bestpath as-path ignore..................................................................................................................................
PAGE 10
neighbor local-as....................................................................................................................................................... 392 neighbor maximum-prefix....................................................................................................................................... 393 neighbor next-hop-self............................................................................................................................................
PAGE 11
timers bgp....................................................................................................................................................................451 timers bgp extended................................................................................................................................................ 452 MBGP Commands.........................................................................................................................................................
PAGE 12
description.................................................................................................................................................................. 486 pfc mode on............................................................................................................................................................... 486 pfc no-drop queues.............................................................................................................................................
PAGE 13
Offline Diagnostic Commands..................................................................................................................................... 529 diag stack-unit........................................................................................................................................................... 529 offline stack-unit.......................................................................................................................................................
PAGE 14
ipv6 dhcp snooping...................................................................................................................................................574 ipv6 dhcp snooping vlan.......................................................................................................................................... 575 ip dhcp snooping binding.........................................................................................................................................
PAGE 15
debug fip snooping rx..................................................................................................................................................... 612 feature fip-snooping....................................................................................................................................................... 613 fip-snooping enable..............................................................................................................................................
PAGE 16
IGMP Commands............................................................................................................................................................ 654 clear ip igmp groups................................................................................................................................................. 654 debug ip igmp...........................................................................................................................................................
PAGE 17
mtu................................................................................................................................................................................705 portmode hybrid........................................................................................................................................................ 707 rate-interval................................................................................................................................................
PAGE 18
Chapter 24: Internet Protocol Security (IPSec).........................................................................759 crypto ipsec transform-set...........................................................................................................................................759 crypto ipsec policy.......................................................................................................................................................... 760 management crypto-policy..................
PAGE 19
show show show show show show show show show show show show show show show arp............................................................................................................................................................................804 arp retries.............................................................................................................................................................. 806 hosts..............................................................................
PAGE 20
show ipv6 flowlabel-zero.............................................................................................................................................. 855 show ipv6 interface........................................................................................................................................................855 show ipv6 mld_host....................................................................................................................................................
PAGE 21
ipv6 router isis................................................................................................................................................................. 896 isis circuit-type................................................................................................................................................................ 897 isis csnp-interval..................................................................................................................................
PAGE 22
clear mac-address-table..........................................................................................................................................940 mac-address-table aging-time................................................................................................................................941 mac-address-table static........................................................................................................................................
PAGE 23
mode.............................................................................................................................................................................984 multiplier......................................................................................................................................................................985 protocol lldp (Configuration)..........................................................................................................................
PAGE 24
ipv6 mld last-member-query-interval....................................................................................................................... 1023 ipv6 mld query-interval................................................................................................................................................ 1023 ipv6 mld query-max-resp-time...................................................................................................................................
PAGE 25
show ipv6 mroute....................................................................................................................................................1058 show ipv6 multicast-cam...................................................................................................................................... 1059 show ipv6 rpf...........................................................................................................................................................
PAGE 26
Chapter 40: Open Shortest Path First (OSPFv2 and OSPFv3).................................................. 1097 OSPFv2 Commands......................................................................................................................................................1097 area default-cost..................................................................................................................................................... 1097 area nssa.................................................
PAGE 27
graceful-restart grace-period................................................................................................................................1147 graceful-restart mode............................................................................................................................................. 1148 ipv6 ospf area............................................................................................................................................................
PAGE 28
ip pim sparse-mode..................................................................................................................................................1194 ip pim sparse-mode sg-expiry-timer....................................................................................................................1195 ip pim ssm-range......................................................................................................................................................
PAGE 29
private-vlan mapping secondary-vlan...................................................................................................................... 1236 switchport mode private-vlan.................................................................................................................................... 1236 Chapter 45: Per-VLAN Spanning Tree Plus (PVST+)................................................................ 1238 description...........................................................
PAGE 30
service-policy input................................................................................................................................................. 1280 service-policy output...............................................................................................................................................1281 service-queue...........................................................................................................................................................
PAGE 31
show config.................................................................................................................................................................... 1326 show ip rip database..................................................................................................................................................... 1327 show running-config rip.....................................................................................................................................
PAGE 32
privilege level (LINE mode)................................................................................................................................... 1372 Obscure Password Commands.................................................................................................................................. 1373 service obscure-passwords...................................................................................................................................
PAGE 33
tacacs-server key......................................................................................................................................................1411 tacacs-server vrf......................................................................................................................................................1412 Port Authentication (802.1X) Commands................................................................................................................
PAGE 34
ip dhcp snooping trust............................................................................................................................................1453 ip dhcp source-address-validation...................................................................................................................... 1453 ip dhcp snooping vlan.............................................................................................................................................
PAGE 35
snmp context............................................................................................................................................................1490 snmp ifmib ifalias long............................................................................................................................................. 1491 snmp-server community........................................................................................................................................
PAGE 36
show redundancy.......................................................................................................................................................... 1556 show system stack-ports............................................................................................................................................ 1557 stack-unit priority.....................................................................................................................................................
PAGE 37
enable......................................................................................................................................................................... 1595 SupportAssist Company Commands........................................................................................................................ 1595 address.......................................................................................................................................................................
PAGE 38
Chapter 62: Uplink Failure Detection (UFD)..............................................................................1631 clear ufd-disable............................................................................................................................................................. 1631 debug uplink-state-group............................................................................................................................................ 1632 description..........................
PAGE 39
show vlt-proxy-gateway..............................................................................................................................................1669 Chapter 66: Virtual Link Trunking (VLT)................................................................................... 1671 back-up destination...................................................................................................................................................... 1672 clear vlt statistics....................
PAGE 40
show show show show show show show vxlan vxlan vxlan vxlan vxlan vxlan vxlan vxlan-instance vxlan-instance vxlan-instance vxlan-instance vxlan-instance vxlan-instance vxlan-instance logical network............................................................................................................. 1706 physical-locator............................................................................................................1706 statistics interface................................................
PAGE 41
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 42
Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
PAGE 43
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 44
User "admin" on line vty0 ( 123.12.1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 45
When entering commands, you can take advantage of the following timesaving features: ● Commands are not case-sensitive. ● Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/1 for the interface tengigabitethernet 1/1/1 command. ● Use the TAB key to complete keywords in commands. ● Use the up Arrow key to display the last enabled command. ● Use either the Backspace key or Delete key to erase the previous character.
PAGE 46
Using the no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration. In this guide, the no form of the command is described in the Syntax portion of the command description.
PAGE 47
Enabling Software Features on Devices Using a Command Option The capability to activate software applications or components on a device using a command is supported on this platform. Starting with Release 9.4(0.0), you can enable or disable specific software features or applications that need to run on a device by using a command attribute in the CLI interface. This enables effective, streamlined management and administration of applications and utilities that run on a device.
PAGE 48
show feature Verify the status of software applications, such as VRF, that are activated and running on a device. Syntax show feature Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated the command to display the IPV6acloptimized feature on the S6100– ON and Z9100–ON. 9.12(1.
PAGE 49
To enter CLASS-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the class-map command, and then enter the class map name. The prompt changes to include config-classmap. You can return to CONFIGURATION mode by using the exit command. CONFIGURATION Mode In EXEC Privilege mode, use the configure command to enter CONFIGURATION mode and configure routing protocols and access interfaces. To enter CONFIGURATION mode: 1. Verify that you are logged in to EXEC Privilege mode. 2.
PAGE 50
EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include conf-mgmt-eis. You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode.
PAGE 51
NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. But in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. The prompt changes to include the designated interface and slot/port[/subport] number.
PAGE 52
1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode. 2. Enter the protocol lldp command. The prompt changes to include conf-lldp or conf-if-interface-lldp. LLDP MANAGEMENT INTERFACE Mode To enable and configure Link Layer Discovery Protocol (LLDP) on management interfaces, use LLDP MANAGEMENT INTERFACE mode. To enter LLDP MANAGEMENT INTERFACE mode: 1. Verify that you are logged in to LLDP mode. 2.
PAGE 53
OPENFLOW INSTANCE Mode To enable and configure OpenFlow instances, use OPENFLOW INSTANCE mode. To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the openflow of-instance command, and then the OpenFlow ID number of the instance you want to create or configure. The prompt changes to include conf-of-instance of-id. You can return to the CONFIGURATION mode by entering the exit command.
PAGE 54
2. Enter the protocol spanning-tree rstp command. The prompt changes to include conf-rstp. You can return to CONFIGURATION mode by using the exit command. ROUTE-MAP Mode To configure a route map, use ROUTE-MAP mode. To enter ROUTE-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the route-map map-name [permit | deny] [sequence-number] command. The prompt changes to include config-route-map. You can return to CONFIGURATION mode by using the exit command.
PAGE 55
To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include conf-router_rip. You can return to CONFIGURATION mode by using the exit command. SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode. For more information, see Spanning Tree Protocol (STP). To enter SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 56
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 57
primary Enter the keyword primary to specify the primary Dell EMC Networking OS image. secondary Enter the keyword secondary to specify the secondary Dell EMC Networking OS image. system: Enter the keyword system: to use the system image file URL (system). ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system.
PAGE 58
cd Change to a different working directory. Syntax cd [flash: | usbflash:] Parameters flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB.
PAGE 59
Password to login remote host: Destination file name [sample_file]: Defaults None. Command Modes EXEC Privilege Command History Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. copy http://admin:admin123@10.16.206.77/sample_file flash://sample_file copy Copy one file to another location.
PAGE 60
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added the nfsmount: parameters that allow you to mount a remote NFS file system. 9.4(0.0) Added the compressed-config parameter. 9.3(0.1) Added the http parameter on the S6000, Z9000, S4810, and S4820T. 9.0.2.
PAGE 61
User name to login remote host: username Password to login remote host: ! 4080 bytes successfully copied DellEMC# In this copy scp: flash: example, specifying SCP in the first position indicates that you need to specify the target in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal flash. The source is on a secure server running secure shell (SSH), so you are prompted for the user datagram protocol (UDP) port of the SSH server on the remote host.
PAGE 62
usbflash: To delete a file or directory on the external USB flash, enter usbflash:// then the filename or directory name ([usbflash://]filepath). no-confirm (OPTIONAL) Enter the keywords no-confirm to specify that the Dell EMC Networking OS does not require user input for each file prior to deletion. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 63
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for NFS mount. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 64
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 65
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Introduced on S4810 and Z9000. 8.3.19.0 Introduced on S4820T. Include the colon (:) when entering this command. This command checks the specified flash memory for errors. If errors are found, the command recommends that you format the flash.
PAGE 66
Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system. username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password. Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 67
Example Related Commands DellEMC# rmdir nfsmount:/nfs-mountpoint/guest Proceed to remove the directory [confirm yes/no]: yes ● mkdir – create a directory. HTTP Copy via CLI Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). Syntax copy http://10.16.206.77/sample_file flash://sample_filecopy flash:// sample_file http://10.16.206.77/sample_file You can copy from the server to the switch and vice-versa.
PAGE 68
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 69
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fan-out, and so forth). When restoring all units in a stack, all the units in the stack are placed into stand-alone mode.
PAGE 70
Example (single stack) Example (NvRAM all stack units) Example (NvRAM, single unit) DellEMC# restore factory-defaults stack-unit 1 clear-all ************************************************************** * Warning - Restoring factory defaults will delete the existing * * startup-config and all persistent settings (stacking, fanout, etc.)* * After restoration the unit(s) will be powercycled immediately.
PAGE 71
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 72
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. E-Series Original command. DellEMC# show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 73
Example Version Description 7.6.1.0 Introduced on the S-Series 7.5.1.
PAGE 74
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 75
ethernet for the current Ethernet CFM configuration fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current FVRP configuration gvrp for the current GVRP configuration host for the current host configuration hardwaremonitor for hardware-monitor action-on-error settings hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current interface configurati
PAGE 76
qos-policyinput for the current input QoS policy configuration qos-policyoutput for the current output QoS policy configuration radius for the current RADIUS configuration redirect-list for the current redirect-list configuration redundancy for the current RPM redundancy configuration resolve for the current DNS configuration rip for the current RIP configuration rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configura
PAGE 77
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for the tunnel and EIS interface types. 9.0.0.0 Added support for the VLT option. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the hardware-monitor option. 7.6.1.
PAGE 78
show startup-config Display the startup configuration. Syntax show startup-config Command Modes EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 79
Command Modes EXEC Privilege Command History Command Fields This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 80
upgrade Upgrade the bootflash image or system image of the management unit. Syntax upgrade boot {all | bootflash—image | bootselector-image} stack-unit {stackunit-number | all} {booted | flash: | ftp: | nfsmount | scp: | tftp: | usbflash:} file-url Parameters boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image.
PAGE 81
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility this command accepts IPv6 host addresses with or without the square brackets.
PAGE 82
stack-unit stack- Enter the keyword stack-unit and specify the stack-unit ID to sync the image unit-id to that stack-unit. Defaults stack-unit all Enter the keyword stack-unit followed by the keyword all to sync the image on all stack-units. tftp: file-url Enter the keyword tftp: and specify the location of the image file in the format //host-ip/filepath or press Enter to launch a prompt sequence.
PAGE 83
1. Upgrade the system image to the new image and configure the primary partition to boot from the new image using the boot system command. 2. Update the startup configuration file with the new set of configurations and then reload the device using the reload command. The new set of configurations are parsed from the startup configuration file and applied to the NVRAM. During the system boot up, the new set of configurations are applied to the system from the updated NVRAM configurations.
PAGE 84
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP).
PAGE 85
• • • • • • • • • • • • • • • • • • • • • show cpu-traffic-stats show debugging show environment show inventory show login statistics show memory show processes cpu show processes ipc flow-control show processes memory show reset-reason show software ifm show system show tech-support ssh-peer-stack-unit telnet telnet-peer-stack-unit terminal length traceroute undebug all virtual-ip write asf-mode Enable alternate store and forward (ASF) mode and forward packets as soon as a threshold is reached.
PAGE 86
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P1) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information You must save the configuration and reload the system to implement ASF.
PAGE 87
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original Command After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
PAGE 88
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the acknowledgement keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 89
banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters Defaults c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator. The delineator is a percent character (%). No banner is configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 90
cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 91
Usage Information Version Description 9.2(0.2) Added support for the fcoe parameter on the S4810 and S4820T. 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dual-qos. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 92
clear average-power Reset the average power and average power start time. Syntax clear average-power stack-unit {stack-unit-number} Parameters Defaults stack-unitnumber Enter the stack unit number. None Command Modes EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 93
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode.
PAGE 94
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example DellEMC# configure DellEMC(conf)# disable Return to EXEC mode. Syntax disable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of the Dell EMC Networking OS. The range is from 0 to 15.
PAGE 95
Version Description E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax Parameters Defaults do command command Enter an EXEC-level command. none Command Modes ● CONFIGURATION ● INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 96
System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Syntax enable [level] Parameters Defaults level (OPTIONAL) Enter a number for a privilege level of Dell EMC Networking OS. The range is from 0 to 15. 15 Command Modes EXEC Command History This guide is platform-specific.
PAGE 97
enable optic-info-update interval Enable polling intervals of optical information updates for simple network management protocol (SNMP). Syntax enable optic-info-update [interval seconds] To disable optical power information updates, use the no enable optic-info-update interval command. Parameters Defaults interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds. The default is 300 seconds (5 minutes).
PAGE 98
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 8.3.19.0 Deprecated command for S4820T. Replaced by the enable optic-infoupdate interval command to update information on temperature and power monitoring in the SNMP MIB. 8.3.11.4 Deprecated command for Z9000. Replaced by the enable optic-infoupdate interval command to update information on temperature and power monitoring in the SNMP MIB. 8.3.10.0 Deprecated command for the S4810 only.
PAGE 99
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. E-Series Original command. ● exit — returns to the lower command mode.
PAGE 100
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. To remove the time interval, enter exec-timeout 0 0. Example Dell con0 is now available Press RETURN to get started. DellEMC> exit Return to the lower command mode.
PAGE 101
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. ● end — returns to EXEC Privilege mode. ftp-server enable Enable FTP server functions on the system.
PAGE 102
Example Version Description E-Series Original command. morpheus% ftp 10.31.1.111 Connected to 10.31.1.111. 220 DellEMC(1.0) FTP server ready Name (10.31.1.
PAGE 103
Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information After you enable FTP server functions with the ftp-server enable command, Dell EMC Networking recommends specifying a top-level directory path. Without a top-level directory path specified, the Dell EMC Networking OS directs users to the flash directory when logging in to the FTP server.
PAGE 104
Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. hostname Set the host name of the system. Syntax hostname name Parameters Defaults name Enter a text string, up to 32 characters long. Dell Command Modes CONFIGURATION Command History Usage Information 104 This guide is platform-specific.
PAGE 105
ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 106
Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF. Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 107
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 108
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.
PAGE 109
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Configure a password with the ip ftp password command. Related Commands ● ip ftp password — sets the password for FTP connections. ip ftp vrf Configures an FTP client with a VRF that is used to connect to the FTP server.
PAGE 110
ip telnet server enable Enable the Telnet server on the switch. Syntax ip telnet server enable To disable the Telnet server, use the no ip telnet server enable command. Defaults Enabled Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 111
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 112
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 113
Usage Information Example Version Description 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. If you configure a TELNET client to use a specific VRF, then you need not explicitly specify the same VRF during the TELNET client sessions corresponding to that VRF. Dell(conf)# ip telnet vrf vrf1 Dell(conf)# do telnet 10.10.10.2 Dell(conf)# no ip telnet vrf vrf1 Dell(conf)# ip tftp source-interface Assign an interface’s IP address in outgoing packets for TFTP traffic.
PAGE 114
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command. Parameters Defaults vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TFTP client.
PAGE 115
Defaults console 0 Enter the keyword console 0 to configure the console port. The console option is <0-0>. vty number Enter the keyword vty then a number from 0 to 9 to configure a virtual terminal line for remote sessions. The system supports 10 remote sessions. end-number (OPTIONAL) Enter a number from 1 to 9 as the last virtual terminal line to configure. You can configure multiple lines at one time. Not configured Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 116
clear-line enable Defaults Enables you to clear your existing sessions. Not configured. You can use all the available sessions. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 117
When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of your existing sessions. Close any of your existing sessions to log in to the system. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'. Login: admin Password: Maximum concurrent sessions for the user reached. Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.97 4 vty 2 10.14.1.97 5 vty 3 10.14.1.
PAGE 118
If you use the login statistics time-period days command to set a custom time period, the system only reports the login statistics during that interval. NOTE: Login statistics are not applicable for login sessions that do not use authentication on user names. For example, the system does not report login activity for a telnet session that prompts only a password field. Example When you log into the system, it displays a message similar to the following: $ telnet 10.11.178.14 Trying 10.11.178.14...
PAGE 119
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 120
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a Tunnel interface, enter the keyword tunnel then a number from 1 to 16383.
PAGE 121
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0)P5 Introduced on the S4048–ON. 9.8(0.0)P2 Introduced on the S3048–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. Added support for the outgoing-interface option for link-local IPv6 addressing on the S4820T. Usage Information 8.3.12.
PAGE 122
Reply to Reply to :: Reply to Reply to Reply to DellEMC# Example (IPv6) request 1 from 172.31.1.216 0 ms request 1 from 172.31.1.205 16 ms request 5 from 172.31.1.209 0 ms request 5 from 172.31.1.66 0 ms request 5 from 172.31.1.87 0 ms DellEMC# ping 100::1 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds: !!!!! Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms) DellEMC# reload Reboot the system.
PAGE 123
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 9.1(0.0) Added ‘conditional’ parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you use only the reload command, the system boots into the Dell EMC Networking OS.
PAGE 124
vty Defaults Enter the keyword vty to send a message to the virtual terminal. none Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 125
Defaults show-timezone (OPTIONAL) Enter the keyword show-timezone to include the time zone information in the timestamp. uptime (OPTIONAL) Enter the keyword uptime to have the timestamp based on time elapsed since system reboot. utc (OPTIONAL) Enter the keyword utc to include the UTC time format (ignoring local time zone) in the timestamp. ● datetime [localtime] ● datetime Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 126
Parameters threshold (OPTIONAL) Enter the keyword threshold to display the temperature thresholds in Celsius for each level. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 127
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 9.1.(0.0) Introduced on S4810. Version 8.3.19.0 Introduced on the S4820T.
PAGE 128
Usage Information Version Description 7.5.1.0 Introduced on the C-Series and E-Series. One trace log message is generated for each command. No password information is saved to this file. A command-history trace log is saved to a file after failover. Dell EMC Networking TAC analyzes this file to help identify the root cause of it. The timestamps display format of the show command-history output changes based on the service timestamps log datetime configuration.
PAGE 129
[1d0h25m]: CMD-(CLI):[end]by default from console [1d0h25m]: CMD-(CLI):[write memory]by default from console Example 4: no service timestamps log DellEMC#show clock 15:55:12.
PAGE 130
Enable privilege mode: enable command usage:3 <0-15> option usage: 0 exit command usage:1 show command-tree command usage:9 count option usage: 3 show version command usage:1 ! Global configuration mode: aaa authentication enable command usage:1 WORD option usage: 1 default option usage: 0 enable option usage: 0 line option usage: 0 none option usage: 0 radius option usage: 1 tacacs+ option usage: 0 Dell# show cpu-traffic-stats View the CPU traffic statistics.
PAGE 131
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series 6.2.1.1 Introduced on the E-Series. Traffic statistics are sorted on a per-interface basis; the interface receiving the most traffic is displayed first. All CPU and port information is displayed unless a specific port or CPU is specified.
PAGE 132
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series E-Series Original command.
PAGE 133
Usage Information Example (all) Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 134
1 2 up AC up 6656 40 26 14/4/2017 17:24 DellEMC#show environment thermal-sensor -- Thermal Sensor Readings (deg C) -- Unit Sensor0 Sensor1 Sensor2 Sensor3 Sensor4 Sensor5 Sensor6 ------------------------------------------------------------------0 39 36 37 37 31 31 46 show inventory Display the switch type, components (including media), and Dell EMC Networking Operating System (OS), including hardware identification numbers and configured protocols.
PAGE 135
Usage Information Example (S4048– ON) If there are no fiber ports in the unit, just the header under show inventory media displays. If there are fiber ports but no optics inserted, the output displays Media not present or accessible. DellEMC# show inventory System Type : S4048-ON System Mode : 1.
PAGE 136
1 S4048T-ON-FAN NA 061DJT X01 TW-061DJT-28298-61J-0174 X01 N/A 0 * - Management Unit Software Protocol Configured ---------------------------BFD BGP LLDP MCAST OSPF RSTP SNMP Spanning-Tree DellEMC# DellEMC# show inventory media Slot Port Type Media Serial Number F10Qualified --------------------------------------------------------------------------------------1 49/1 QSFP 40GBASE-CR4-1M APF11150011EE7 Yes 1 49/2 QSFP 40GBASE-CR4-1M APF11150011EE7 Yes 1 49/3 QSFP 40GBASE-CR4-1M APF11150011EE7 Yes 1 49
PAGE 137
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced the successful-attempts keyword. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 138
----------------------------------------------------------------------------------------------------------------------------------User: admin2 Last login time: 12:49:27 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 139
show memory View current memory usage on the switch. Syntax Parameters show memory [stack-unit id] stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack unit ID to display memory information on the designated stack member. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 140
stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack member ID. As an option of the show processes cpu command, this option displays CPU usage for the designated stack member. Or, as an option of the command, this option limits the output of memory statistics to the designated stack member. Refer to Example (stack-unit). summary (OPTIONAL) Enter the keywordsummary to view CPU utilization of processes related to stack-unit processing.
PAGE 141
frrpagt 0xbacf3000 F10StkMgr 0xbad0c000 lcMgr 0xbad24000 dla 0xbad44000 sysAdmTsk 0xbad58000 timerMgr 0xbad6e000 PM 0xbad85000 KP 0xbad9a000 evagt 0xbadb4000 ipc 0xbadc9000 sysReaper 0xbae22000 tme 10 1 10000 0.00% 0.00% 0.00% 0 710 71 10000 0.00% 0.00% 0.03% 0 30 3 10000 0.00% 0.00% 0.00% 0 50 5 10000 0.00% 0.00% 0.00% 0 650 65 10000 0.00% 0.00% 0.00% 0 50 5 10000 0.00% 0.00% 0.00% 0 1190 119 10000 0.00% 0.00% 0.00% 0 0 0 0 0.00% 0.00% 0.
PAGE 142
PID Runtime(ms) Process 0x00000000 45040 system 0x000001ac 25750 sysdlp 0x0000019a 10650 sysd 0x000003a5 860 clish 0x000001ad 520 lacp 0x000004ba 330 clish 0x000000c9 1240 nvmgr 0x000000e0 530 igmp 0x00000132 420 vrrp 0x0000028d 410 ovsdbsvr 0x000000a9 200 arpm 0x00000253 100 otm 0x00000206 140 tnlmgr 0x00000012 1290 mount_mfs 0x0000024d 40 xstp DellEMC# Related Commands Invoked uSecs 5Sec 1Min 4504 10000 13.12% 13.20% 12.94% 0 2575 10000 2.78% 2.48% 3.40% 0 1065 10000 0.60% 1.16% 2.
PAGE 143
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 144
DHCP0 IPMGR0 DHCP0 IPMGR1 DHCP0 IFMGR0 IPMGR0 NDPM0 IFMGR0 FEFD0 IFMGR0 SNMP0 IFMGR0 SFL_CP0 IFMGR0 PORTMIRR0 IFMGR0 EVENTTERMLOG0 IFMGR0 IPSECMGR0 IFMGR0 DHCP0 IFMGR0 IPMGR0 IFMGR0 IFAGT3 IFAGT3 IFMGR0 IFMGR0 OFMGR0 IFMGR0 ACL0 IFMGR0 VRRP0 IFMGR0 PIM0 IFMGR0 MACMGR0 IFMGR0 L2PM0 IFMGR0 DIFFSERV0 IFMGR0 RTM0 IFMGR0 LLDP0 IFMGR0 MRTM0 IFMGR0 IPMGR1 IFMGR0 LACP0 PORTMIRR0 ACL_AGENT2 IFMGR0 IGMP0 IFMGR0 IFAGT2 DellEMC# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 1 20 8 1 8 8 29 1 1
PAGE 145
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.7.1.0 Added the management-unit option. 7.6.1.0 Introduced on the S-Series.
PAGE 146
Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249856 50572 0 50572 50572 323 frrp 5206016 241664 369238 0 369238 369238 322 xstp 7430144 2928640 38328 0 38328 38328 321 pim 5267456 823296 62168 0 62168 62168 314 igmp 4960256 380928 18588 16564 18588 2024 313 mrtm 6742016 1130496 72758 0 72758 72758 308 l2m
PAGE 147
Example — System reboot due to the upgrade command Example — System reboot for unknown reasons DellEMC# show reset-reason Cause: Reboot by Software upgrade Module. Reset Time: 8/9/2017 1:39 PM. DellEMC# show reset-reason Cause: N/A Reload Time: N/A Example — The example shows that the last system reboot was due to warm reset. System reboot due to power loss DellEMC#show reset-reason or pressing the Cause : Warm Reset Reset Time : N/A. power button off and on.
PAGE 148
show software ifm Display interface management (IFM) data. Syntax show software ifm {clients [summary] | ifagt number | ifcb interface | stack-unit unit-ID | trace-flags} Parameters clients Enter the keyword clients to display IFM client information. summary (OPTIONAL) Enter the keyword summary to display brief information about IFM clients. ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics.
PAGE 149
L2PM 0 0x00000000 0x00000000 0x87ff79ff 0x0e032200 45 ACL 0 0x00000000 0x00000000 0x867f50c3 0x000f0218 44 OSPF 0 0x00000dfa 0x00400098 0x00000000 0x00000000 0 PIM 0 0x000000f3 0x00030000 0x00000000 0x00000000 0 IGMP 0 0x000e027f 0x00000000 0x00000000 0x00000000 0 SNMP 0 0x00000000 0x00000000 0x800302c0 0x00000002 30 EVTTERM 0 0x00000000 0x00000000 0x800002c0 0x00000000 29 MRTM 0 0x00000000 0x00000200 0x81f7103f 0x00000000 38 DSM 0 0x00000000 0x00000000 0x80771003 0x00000000 32 LACP 0 0x00000000 0x00000000
PAGE 150
Version Description 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot co display as "Present". 7.7.1.0 Added Master Priority field. 7.6.1.0 Introduced on the S-Series.
PAGE 151
Current Type : S4048-ON - 54-port TE/FG (SK-ON) Master priority : 0 Hardware Rev : 2.0 Num Ports : 72 Up Time : 2 day, 20 hr, 49 min Dell EMC Networking OS Version : 9.13(0.0) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : 3.21.2.9 Boot Selector : 3.21.0.
PAGE 152
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated to display the show revision and show os-version command outputs. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 153
Example (options under show techsupport) DellEMC# show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command DellEMC#show tech-support stack-unit 1 ? | Pipe through a command DellEMC# show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence of a pattern grep Show only text that matches a pattern no-more Don't paginate output save Save output to a file DellEMC# show tech-support stack-unit 1 | save
PAGE 154
boot flash 3.21.2.9 Control Processor passed BOOTSEL IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target checksum boot selector 3.21.0.0-5 Control Processor passed FPGA IMAGE INFORMATION : --------------------------------------------------------------------Card FPGA Name Version stack-unit 1 S4048-ON SYSTEM CPLD 15.
PAGE 155
--------------------------------------------------------------------Type Version Target checksum boot selector 3.27.0.
PAGE 156
6 Forty GigabitEthernet/IEEE 802.3 interface(s) ssh-peer-stack-unit Open an SSH connection to the peer stack-unit. Syntax ssh-peer-stack-unit [-l username] Parameters Defaults -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 157
source-interface Defaults (OPTIONAL) Enter the keywords /source-interface then the interface information to include the source interface. Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 158
The source interface configured using this command has a higher precedence than the source interface configured using the ip telnet source-interface command. If you do not configure a source interface using this command, then the TELNET client uses the source interface configured using the ip telnet source-interface command. In case there is a mismatch between the VRF telnet source interface and the telnent VRF, then an error is reported. Example DellEMC# telnet vrf vrf1 10.10.10.
PAGE 159
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 160
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 161
Example (IPv6) DellEMC# traceroute 100::1 Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 100::1, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 100::1 000.000 ms 000.000 ms 000.000 ms DellEMC#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort.
PAGE 162
Version Description E-Series Original command. virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6-address} command. Parameters ipv4-address Enter the IP address of the active management interface in a dotted decimal format (A.B.C.D.).
PAGE 163
write Copy the current configuration to either the startup-configuration file or the terminal. Syntax Parameters write [memory [compressed] | terminal] memory Enter the keyword memory to copy the current running configuration to the startup configuration file. This command is similar to the copy running-config startup-config command. compressed Enter the keyword compressed to write the operating configuration to the startup-config file in the compressed mode.
PAGE 164
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 165
debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x. interface Restricts the debugging information to an interface.
PAGE 166
max-attempts number Defaults (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 167
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 168
Usage Information Version Description 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: ● Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). ● Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command). In MAB-only authentication mode, a port authenticates using the host MAC address even though 802.1xauthentication is enabled.
PAGE 169
dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 170
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 171
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 172
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series.
PAGE 173
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode.
PAGE 174
Parameters Defaults force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. None Command Modes Auto Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 175
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.
PAGE 176
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command.
PAGE 177
To return to the default, use the no dot1x server-timeout command. Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. 30 seconds Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 178
Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 179
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 180
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. Enter a supplicant’s MAC address using the mac-address option to display CoS mapping information only for the specified supplicant. You can display the CoS mapping information applied to traffic from authenticated supplicants on 802.
PAGE 181
Defaults None Command Modes ● EXEC ● EXEC privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 182
Example (macaddress) DellEMC# show dot1x interface tengigabitethernet 1/32 mac-address 00:00:00:00:00:10 Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.
PAGE 183
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 184
• • • • • • • • • • • • • permit tcp (for Extended IP ACLs) seq arp (for Extended MAC ACLs) seq ether-type (for Extended MAC ACLs) seq (for IP ACLs) seq (for IPv6 ACLs) permit udp (for IPv6 ACLs) permit tcp (for IPv6 ACLs) permit icmp (for IPv6 ACLs) permit (for IPv6 ACLs) deny udp (for IPv6 ACLs) deny tcp (for IPv6 ACLs) deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
PAGE 185
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode.
PAGE 186
Related Commands ● show config — display the current ACL configuration. show config Display the current ACL configuration. Syntax show config Command Modes ● ● ● ● Command History Example 186 CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 187
Common IP ACL Commands The following commands are available within both Ingress and Egress IP ACL modes (Standard and Extended) and do not have mode-specific options. When an ACL is created without a rule and then is applied to an interface, ACL behavior reflects an implicit permit. The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line.
PAGE 188
Usage Information When you use the access-class access-list-name command without specifying the ipv4 or ipv6 attribute, both IPv4 as well as IPv6 rules that are defined in that ACL are applied to the terminal. This method is a generic way of configuring access restrictions. To be able to filter access exclusively using either IPv4 or IPv6 rules, use either the ipv4 or ipv6 attribute along with the access-class access-list-name command.
PAGE 189
ip access-group Assign an IP access list (IP ACL) to an interface. Syntax ip access-group access-list-name {in | out} [implicit-permit] [vlan vlanid] [layer3] [vrf vrf-name] To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id][layer3] [vrf vrf-name] command. Parameters Defaults access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic.
PAGE 190
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. You can assign one ingress ACL and one egress ACL to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces.
PAGE 191
Related Commands Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T–ON, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, and Z9500. ● ip access-list standard — configure a standard ACL. ● ip access-list extended — configure an extended ACL. ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 192
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. in | out Identify whether ACL is applied on the ingress or egress side. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to view the IP accounting information on either a default or a non-default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 192 This guide is platform-specific.
PAGE 193
Example DellEMC# show ip accounting access-list L3-ACL vrf vrf3 ! Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1.2.0/24 any negotiate 150 monitor 300 count (0 packets) seq 10 permit 20.1.2.0/24 seq 15 permit 30.1.2.0/24 DellEMC# show ip access-lists Display all of the IP ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/ mismatches against each ACL entry displayed.
PAGE 194
NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny To drop packets with a certain IP address, configure a filter. Syntax deny {source | any | host {ip-address}} [count [bytes] | log] [dscp value] [ecn value] [fragments] [monitor] [no-drop] [order] To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command.
PAGE 195
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.
PAGE 196
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.
PAGE 197
Defaults log (OPTIONAL) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match the IP DSCP values. The range is from 0 to 63. ecn (OPTIONAL) Enter the keyword ecn to match the ECN bits. The range is from 0 to 3. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority).
PAGE 198
Version Description 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide. Related Commands ● deny — assign a IP ACL filter to deny IP packets. ● ip access-list standard — create a standard ACL.
PAGE 199
Usage Information Version Description 7.4.1.0 Introduced on the E-Series. When you have exhausted all the sequence numbers, this feature permits re-assigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter.
PAGE 200
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 201
The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny Configure a filter that drops IP packets meeting the filter criteria.
PAGE 202
Defaults fragments Enter the keyword fragments to use ACLs to control packet fragments. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter.
PAGE 203
Related Commands ● deny tcp — assign a filter to deny TCP packets. ● deny udp — assign a filter to deny UDP packets. ● ip access-list extended — create an extended ACL. deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 204
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(2.0P0) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.11(0.0) Added support for session–ID to the monitor parameter.
PAGE 205
Parameters source Enter the IP address of the network or host from which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. ttl Enter the keyword ttl to deny a packet based on the time to live value.
PAGE 206
Defaults fragments Enter the keyword fragments to use ACLs to control packet fragments. monitor (OPTIONAL) Enter the keyword monitor to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, see Flow-based Monitoring in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Not configured.
PAGE 207
The C-Series and S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
PAGE 208
● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values.
PAGE 209
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.
PAGE 210
Total Ports: 1024 Related Commands ● deny — assign a filter to deny IP traffic. ● deny tcp — assign a filter to deny TCP traffic. ip access-list extended Name (or select) an extended IP access list (IP ACL) based on IP addresses or protocols. Syntax ip access-list extended access-list-name To delete an access list, use the no ip access-list extended access-list-name command. Parameters Defaults access-list-name Enter a string up to 140 characters long as the access list name.
PAGE 211
Related Commands ● ip access-list standard — configure a standard IP access list. ● show config — display the current configuration. permit To pass IP packets meeting the filter criteria, configure a filter.
PAGE 212
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 213
To remove this filter, you have two choices: ● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no permit tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 214
Defaults order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments.
PAGE 215
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes increment.
PAGE 216
Defaults host ip-address Enter the keyword host and then enter the IP address to specify a host IP address. ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 217
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 218
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. DellEMC# Data Mask 1 0000000000000000 1111110000000000 0 From To #Covered 1023 1024 Total Ports: 1024 Related Commands ● ip access-list extended — create an extended ACL. ● permit — assign a permit filter for IP packets. ● permit tcp — assign a permit filter for TCP packets. resequence access-list Re-assign sequence numbers to entries of an existing access-list.
PAGE 219
Usage Information When all sequence numbers are exhausted, this feature permits re-assigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 220
Defaults operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 221
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 222
clear counters mac access-group Clear counters for all or a specific MAC ACL. Syntax clear counters mac access-group [mac-list-name] Parameters mac-list-name (OPTIONAL) Enter the name of a configured MAC access list. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 223
out Enter the keyword out to configure the ACL to filter outgoing traffic. NOTE: 1. If the MAC ACL is applied on VLAN, none of the VLAN members should have an access list applied for that VLAN. 2. If the MAC ACL is applied on a Physical or Port Channel interface, the VLAN in which this port is associated should not have an access list applied. 3. If the MAC ACL is applied on a VLAN, then that VLAN should not belong to VLAN ACL group. 4.
PAGE 224
show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed. Syntax show mac access-lists [access-list-name] [interface interface] [in | out] Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters.
PAGE 225
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. in | out Identify whether ACL is applied on ingress or egress side.
PAGE 226
Standard MAC ACL Commands When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. These commands configure standard MAC ACLs and support both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets with a the MAC address specified, configure a filter.
PAGE 227
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 228
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Dell EMC Networking OS supports one ingress and one egress MAC ACL per interface. The number of entries allowed per ACL is hardware-dependent. For detailed specifications about entries allowed per ACL, see your line card documentation. NOTE: Ingress ACLs are supported on C-Series and S-Series platforms only.
PAGE 229
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 230
Defaults log (OPTIONAL) Enter the keyword log to include ACL messages in the log. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated.
PAGE 231
Extended MAC ACL Commands When an access-list is created without any rule and then applied to an interface, ACL behavior reflects implicit permit. The following commands configure Extended MAC ACLs. The platform supports both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets that match the filter criteria, configure a filter.
PAGE 232
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 233
Parameters access-list-name Enter a text string as the MAC access list name, up to 140 characters. cpu-qos Defaults Enter the keywords cpu-qos to assign this ACL to control plane traffic only (CoPP). None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 234
seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands ● mac access-list standard — configure a standard MAC access list. ● show mac accounting access-list — display MAC access list configurations and counters (if configured). permit To pass packets matching the criteria specified, configure a filter.
PAGE 235
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 236
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 237
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 238
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 239
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 240
Example Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf-nprefixl)# show config ! ip prefix-list snickers DellEMC(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. Syntax show ip prefix-list detail [prefix-name] Parameters prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters.
PAGE 241
ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 seq 5 permit 1.1.1.0/24 (hit count: 0) seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) DellEMC# show ip prefix-list summary Display a summary of the configured prefix lists. Syntax Parameters show ip prefix-list summary [prefix-name] prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters.
PAGE 242
Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit. To configure route maps and their redistribution criteria, use the following commands. continue To a route-map entry with a higher sequence number, configure a route-map. Syntax continue [sequence-number] Parameters Defaults sequencenumber (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Not configured.
PAGE 243
● If the next route map entry contains a continue clause, the route map executes the continue clause if a successful match occurs. ● If the next route map entry does not contain a continue clause, the route map evaluates normally. If a match does not occur, the route map does not continue and falls through to the next sequence number, if one exists.
PAGE 244
match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command. Parameters Defaults as-path-name Enter the name of an established AS-PATH ACL, up to 140 characters. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific.
PAGE 245
exact Defaults (OPTIONAL) Enter the keywords exact to process only those routes with this community list name. Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 246
Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 247
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 248
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 249
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 250
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface.
PAGE 251
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. pre-6.1.1.0 Introduced on the E-Series. match route-type To match routes based on the how the route is defined, configure a filter. Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command.
PAGE 252
Related Commands Version Description pre-6.1.1.0 Introduced on the E-Series. ● ● ● ● ● ● match match match match match match interface — redistribute routes that match the next-hop interface. ip address — redistribute routes that match an IP address. ip next-hop — redistribute routes that match the next-hop IP address. ip route-source — redistribute routes that match routes advertised by other routers. metric — redistribute routes that match a specific metric.
PAGE 253
● match metric — redistribute routes that match a specific metric. ● match route-type — redistribute routes that match a route type. route-map Enable a route map statement and configure its action and sequence number. This command also places you in ROUTE-MAP mode. Syntax route-map map-name [permit | deny] [sequence-number] To delete a route map, use the no route-map map-name [permit | deny] [sequencenumber] command.
PAGE 254
Usage Information Example Related Commands Use caution when you delete route maps because if you do not specify a sequence number, all route maps with the same map-name are deleted when you use the no route-map map-name command. DellEMC(conf)# route-map dempsey DellEMC(config-route-map)# ● show config — display the current configuration. set as-path To modify the AS path for border gateway protocol (BGP) routes, configure a filter. Syntax set as-path prepend as-number [...
PAGE 255
set automatic-tag To automatically compute the tag value of the route, configure a filter. Syntax set automatic-tag To return to the default, enter no set automatic-tag. Defaults Not configured. Command Modes ROUTE-MAP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 256
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 257
no-advertise Enter the keywords no-advertise to drop all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to drop all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary.
PAGE 258
Parameters Defaults backbone Enter the keyword backbone to redistribute matched routes to the OSPF backbone area (area 0.0.0.0). level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Not configured.
PAGE 259
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 260
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 261
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 262
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you configure the set next-hop command, its configuration takes precedence over the neighbor next-hop-self command in the ROUTER BGP mode.
PAGE 263
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command. Parameters Defaults tag-value Enter a number as the tag. The range is from zero (0) to 4294967295.
PAGE 264
set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Syntax set weight weight To delete a weight specification, use the no set weight weight command. Parameters weight Enter a number as the weight used by the route meeting the route map specification. The range is from 0 to 65535. The default is router-originated = 32768 and all other routes = 0.
PAGE 265
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 266
Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 267
Usage Information Example Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 268
IP Community List Commands IP community list commands are supported on the Dell EMC Networking OS. ip community-list Enter COMMUNITY-LIST mode and create an IP community-list for BGP. Syntax ip community-list comm-list-name To delete a community-list, use the no ip community-list comm-list-name command. Parameters comm-list-name Enter a text string as the name of the community-list, up to 140 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 269
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 270
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. ip access-list standard — configures a standard ACL. ip access-list extended — creates an extended ACL.
PAGE 271
length bytes Defaults Enter the keyword length then the length value. The range is from 2 to 24, in multiples of 2 bytes. None Command Modes CONFIGURATION-UDF TCAM Example Command History Dell(conf-udf-tcam)#key innerL3header udf-id 6 packetbase innerL3Header offset 0 length 2 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 272
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON. udf-tcam — creates a context for UDF TCAM. show config — displays the current UDF TCAM profile configuration. permit ip Associate the UDF in IP access-list.
PAGE 273
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON.
PAGE 274
Parameters Defaults name Enter the UDF qualifier value profile name, up to 64 characters. None Command Modes CONFIGURATION-UDF TCAM Example Command History Dell(conf-udf-tcam)# udf-qualifier-value ipnip_val1 This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.10(0.
PAGE 275
● Use the no seq sequence-number command if you know the filter’s sequence number. ● Use the no deny {source [mask] | any | host ip-address} command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 276
Related Commands ● ip access-list standard — configure a standard ACL. ● permit — configure a permit filter. deny (for Extended IP ACLs) Configure a filter that drops IP packets meeting the filter criteria.
PAGE 277
Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 278
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 279
● Use the no deny tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters Defaults ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value.
PAGE 280
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 281
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.
PAGE 282
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 283
Defaults operator Enter one of the following logical operand: ● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 284
looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG).
PAGE 285
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 286
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 287
Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 288
which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 289
permit arp (for Extended MAC ACLs) Configure a filter that forwards ARP packets meeting this criteria. This command is supported only on 12-port GE line cards with SFP optics; refer to your line card documentation for specifications.
PAGE 290
looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). permit ether-type (for Extended MAC ACLs) Configure a filter that allows traffic with specified types of Ethernet packets.
PAGE 291
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 292
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 293
● eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. ● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 294
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 295
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 296
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 297
seq (for Standard MAC ACLs) To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax seq sequence-number {deny | permit} {any | mac-source-address [mac-sourceaddress-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 298
be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 299
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 300
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. You can enter a threshold in the range of 1-100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. You can enter an interval in the range of 1-10 minutes.
PAGE 301
seq ether-type (for Extended MAC ACLs) Configure an egress filter with a specific sequence number that filters traffic with specified types of Ethernet packets. This command is supported only on 12-port GE line cards with SFP optics. For specifications, refer to your line card documentation. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here.
PAGE 302
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 303
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 304
ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list permits all IP protocols. tcp Enter the keyword tcp to configure a TCP access list filter. udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) .
PAGE 305
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 306
● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 307
looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). permit tcp (for IPv6 ACLs) Configure a filter to pass TCP packets that match the filter criteria.
PAGE 308
● neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. ● gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. ● lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. ● range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values.
PAGE 309
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 310
which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 311
permit (for IPv6 ACLs) To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP.
PAGE 312
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 313
Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 314
Parameters source address mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all routes are subject to the filter. host ipv6- Enter the keyword host then the IP address to specify a host IP address. address destination address Enter the IPv6 address of the network or host to which the packets are sent.
PAGE 315
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History Usage Information This guide is platform-specific.
PAGE 316
deny icmp (for Extended IPv6 ACLs) Configure a filter to drop all or specific ICMP messages. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here. For a complete description on all of the keywords and variables that are available with this command, refer the topic of this command discussed earlier in this guide.
PAGE 317
Usage Information Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P0) Added the type parameter to filter the ICMP packets based on the type and code on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 318
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. no-drop Enter the keywords no-drop to match only the forwarded packets.
PAGE 319
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements. Topics: • • • • • • • • • • member vlan ip access-group show acl-vlan-group show cam-acl-vlan cam-acl-vlan show cam-usage show running config acl-vlan-group acl-vlan-group show acl-vlan-group detail description (ACL VLAN Group) member vlan Add VLAN members to an ACL VLAN group.
PAGE 320
Attaching an ACL individually to VLAN interfaces is similar to the behavior of ACL-VLAN mapping storage in CAM prior to the implementation of the ACL VLAN group functionality. ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax ip access-group {group name} out implicit-permit Parameters Default group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 321
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
PAGE 322
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage. During the initialization of CAM, the chassis manager reads the NVRAM and allocates the dynamic VCAP regions.
PAGE 323
Default If you use the default keyword with the cam-acl-vlan command, the FP blocks allocated for VLAN processes are restored to their default values. No FP blocks or dynamic VLAN Content Aware Processor (VCAP) groups are allocated for VLAN operations by default. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 324
Example 1: Output of the show cam-usage Command 324 Field Description StackUnit The Stack unit number Portpipe The hardware path that packets follow through a system for ACL optimization CAM Partition Type of area in the CAM block that is used for ACL VLAN groups Total CAM Total amount of space in the CAM block Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs DellEMC#show cam-usage Stackunit|Portpipe|
PAGE 325
| | OUT-V6 ACL | 178 | Codes: * - cam usage is above 90%.
PAGE 326
| OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | 3 | 0 | IN-L3 FIB | 49152 | | | IN-L3 ACL | 1024 | | | IN-V6 ACL | 0 | | | OUT-L3 ACL | 178 | | | OUT-V6 ACL | 178 | Codes: * - cam usage is above 90%.
PAGE 327
Examples The following sample output shows the line-by-line style display when using the show runningconfig acl-vlan-group option. Note that no group or access list names are truncated Dell #show running-config acl-vlan-group ! acl-vlan-group Test member vlan 1-100 ip access-group test in DellEMC#show running-config acl-vlan-group ! acl-vlan-group Test member vlan 1-100 ip access-group test in DellEMC# Test acl-vlan-group Create an ACL VLAN group.
PAGE 328
show acl-vlan-group detail Display all the ACL VLAN Groups or display a specific ACL VLAN Group by name. To display the names in their entirety, the output displays in a line-by-line format. Syntax show acl-vlan-group detail Parameters detail Display information in a line-by-line format to display the names in their entirety. Without the detail option, the output is displayed in a table style and information may be truncated.
PAGE 329
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.
PAGE 330
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 331
ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
PAGE 332
You can only enable BFD for VRRP in INTERFACE command mode (vrrp bfd all-neighbors). You can enable BFD on both default and nondefault VRFs for OSPF and BGP protocols for both IPv4 and IPv6 neighbors. NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd enable (Configuration) Enable BFD on all interfaces. Syntax bfd enable Disable BFD using the no bfd enable command. Defaults BFD is disabled by default.
PAGE 333
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd interval Specify non-default BFD session parameters beginning with the transmission interval.
PAGE 334
Example Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC(conf-if-te-1/3)# bfd interval 250 min_rx 300 multiplier 4 role passive DellEMC(conf-if-te-1/3)# bfd protocol-liveness Enable the BFD protocol liveness feature.
PAGE 335
To disable BFD for all neighbors configured through static routes, use the no ip route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command. Parameters prefix-list prefix- (Optional) Enter the keyword prefix-list followed by the name of the prefix list-name list to enable or disable BFD on specific neighbors.
PAGE 336
ipv6 route bfd Enable BFD for all IPv6 neighbors configured through static routes. Syntax ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] To disable BFD for all IPv6 neighbors configured through static routes, use the no ipv6 route bfd [vrf vrf-name] [prefix-list prefix-list-name] [interval interval min_rx min_rx multiplier value role {active | passive}] command.
PAGE 337
To disable all BFD sessions on an OSPF interface implicitly, use the no ip ospf bfd allneighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface. interval (OPTIONAL) Enter the keyword interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200.
PAGE 338
Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface. interval (OPTIONAL) Enter the keyword interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200. milliseconds min_rx milliseconds Enter the keywords min_rx to specify the minimum rate at which the local system receives control packets from the remote system. The range is from 50 to 1000. The default is 200.
PAGE 339
min_rx milliseconds Enter the keywords min_rx to specify the minimum rate at which the local system would like to receive control packets from the remote system. The range is from 50 to 1000. The default is 200. multiplier value Enter the keywords multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3.
PAGE 340
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and non-default VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 341
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail Defaults (OPTIONAL) Enter the keyword detail to view detailed information about BFD neighbors. None Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.
PAGE 342
The following example shows the show bfd vrf neighbors command output showing the nondefault VRF. DellEMC(conf)#do sho bfd vrf vrf2 neighbors * Ad Dn B C I O O3 R M V VT - Active session role Admin Down BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr VRF Clients * 13.1.1.1 R Example (Detail) RemoteAddr Interface State Rx-int Tx-int Mult 13.1.1.2 Te 1/2 Up 200 200 3 2 * 23.1.1.1 R 23.1.1.2 Vl 300 Up 200 200 3 2 * 33.1.1.1 R 33.1.1.
PAGE 343
Neighbor parameters: TX: 200ms, RX: 200ms, Multiplier: 3 Actual parameters: TX: 200ms, RX: 200ms, Multiplier: 3 Role: Active Delete session on Down: True VRF: VRF_blue Client Registered: OSPF Uptime: 00:00:15 Statistics: Number of packets received from neighbor: 78 Number of packets sent to neighbor: 78 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Session Discriminator: 6 Neighbor Discriminator: 1 Local Addr: 7.1.
PAGE 344
Related Commands 344 Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for VLAN and port-channel interfaces on the E-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 345
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 346
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 347
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 348
Defaults Disabled Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 349
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
PAGE 350
bgp asnotation asdot DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asdot+ DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process.
PAGE 351
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipathrelax command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 352
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The software compares the MEDs only if the path contains no external autonomous system numbers.
PAGE 353
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 354
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 355
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster.
PAGE 356
The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation. Dell EMC Networking OS accepts confederation EBGP peers without a LOCAL_PREF attribute. The software sends AS_CONFED_SET and accepts AS_CONFED_SET and AS_CONF_SEQ.
PAGE 357
Usage Information All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. After specifying autonomous systems numbers for the BGP confederation, recycle the peers to update their configuration. Related Commands ● bgp confederation identifier — configure a confederation ID.
PAGE 358
max-suppresstime (OPTIONAL) Enter the maximum number of minutes a route can be suppressed. The default is four times the half-life value. The range is from 1 to 255. The default is 60 minutes. route-map map- (OPTIONAL) Enter the keyword route-map then the name of a configured route map. name Only match commands in the configured route map are supported. Defaults Disabled. Command Modes ● ROUTER BGP ● ROUTER BGP-address-family Command History Usage Information This guide is platform-specific.
PAGE 359
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 360
Usage Information Configuring or un-configuring the command brings down and brings up the BGP Route Manager, this results in tear down and re-establishment of all active sessions. Link Bandwidth has to be configured on the router to tell it to associate Link Bandwidth with prefixes (paths) and/or to use Link Bandwidth in BGP Multipath route selection. This is done under BGP configuration and is supported per address family – for IPv4 and IPv6 address families.
PAGE 361
bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails. Syntax bgp fast-external-fallover To disable fast external fallover, use the no bgp fast-external-fallover command. Defaults Enabled Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 362
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 363
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 364
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive.
PAGE 365
Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 366
Usage Information Version Description 9.14(0.1) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6010–ON, and Z9100– ON. After configuring the bgp redistribute-internal command, use the clear ip bgp * command to clear all BGP sessions. If you don’t clear all BGP sessions, route redistribution happens only for new routes. NOTE: When you enable redistribution of iBGP routes into an IGP, ensure that you use route maps to control what prefixes are redistributed.
PAGE 367
Usage Information Version Description 7.6.1.0 Introduced BGP uses regular expressions (regex) to filter route information. In particular, the use of regular expressions to filter routes based on AS-PATHs and communities is common. In a large-scale configuration, filtering millions of routes based on regular expressions can be quite CPU intensive, as a regular expression evaluation involves generation and evaluation of complex finite state machines.
PAGE 368
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router.
PAGE 369
flap-statistics Enter the keywords flap-statistics to clear the flap statistics information. ipv4 Enter the ipv4 address family to clear. ipv6 Enter the ipv6 address family to clear. peer-group Enter the peer-group to clear all members of the peer-group. Command Modes EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 370
ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to clear the ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to clear the ipv6 unicast routes. ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to clear dampening information only that BGP neighbor.
PAGE 371
NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF. You can also use this attribute to return the suppressed routes corresponding to a specific VRF to an active state. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to clear information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to clear information related only to ipv4 unicast routes.
PAGE 372
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information If you enter the clear ip bgp flap-statistics command without any parameters, all statistics are cleared. Related Commands ● show debugging — view the enabled debugging operations. ● show ip bgp flap-statistics — view the BGP flap statistics. ● undebug all — disable all debugging operations.
PAGE 373
Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. deny bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic.
PAGE 374
Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to debug BGP information corresponding to that VRF. NOTE: Use this attribute to debug BGP protocol operations corresponding to either a default or non-default VRF. A.B.C.D Enter the IPv4 address of the neighbor in dotted decimal format. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peer- Enter the keywords peer-group then the name of the peer group to debug.
PAGE 375
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. To view information on both incoming and outgoing routes, do not include the in and out parameters in the debugging command. The in and out parameters cancel each other; for example, if you enter the debug ip bgp in command and then enter the debug ip bgp out command, you do not see information on the incoming routes. Entering a no debug ip bgp command removes all configured debug commands for BGP.
PAGE 376
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced IPv6 MGBP support for the E-Series. debug ip bgp events Display information on local BGP state changes and other BGP events. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] events [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 377
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp keepalives Display information about BGP keepalive messages. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] keepalives [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 378
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] notifications [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] notifications [in | out] command.
PAGE 379
debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group-name] softreconfiguration To disable, use the debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peergroup-name] soft-reconfiguration command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable soft-reconfiguration debugging on that VRF. A.B.C.
PAGE 380
debug ip bgp updates Allows you to view information about BGP updates. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] updates [in | out | prefix-list prefix-list-name] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] updates [in | out | prefix-list prefix-listname] command.
PAGE 381
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. default-metric Allows you to change the metric of redistributed routes to locally originated routes. Use this command with the redistribute command. Syntax default-metric number To return to the default setting, use the no default-metric command. Parameters Defaults number Enter a number as the metric to be assigned to routes from other protocols. The range is from 1 to 4294967295.
PAGE 382
To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the BGP protocol (80 characters maximum). none Command Modes ROUTER BGP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 383
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 384
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 385
Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group. Defaults send Enter the keyword send to indicate that the system sends multiple paths to peers. receive Enter the keyword receive to indicate that the system accepts multiple paths from peers. both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported.
PAGE 386
● seconds = 30 seconds (external peers) Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 387
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path.
PAGE 388
Usage Information You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. Related Commands ● bgp four-octet-as-support — enable 4-byte support for the BGP process. neighbor default-originate Inject the default route to a BGP peer or neighbor.
PAGE 389
When you apply a default route to a BGP peer or peer group using the neighbor defaultoriginate command, changes to the configured default route-map are applied to the BGP peer or peer group only after a delay of 15 seconds. As a result, you must wait for a period of 15 seconds before manually resetting BGP using the clear ip bgp command. In case of eBGP, the neighbor default-originate command does not support extendedcommunity as a non-transtive route-map attribute.
PAGE 390
neighbor distribute-list Distribute BGP information via an established prefix list. Syntax neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 391
To disallow and disconnect connections, use the no neighbor {ip-address | peer-groupname} ebgp-multihop command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. ttl Defaults (OPTIONAL) Enter the number of hops as the Time to Live (ttl) value. The range is from 1 to 255. The default is 255. Disabled. Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific.
PAGE 392
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 393
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 394
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 395
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you configure the set next-hop command in ROUTE-MAP mode, the configuration takes precedence over the neighbor next-hop-self command. If you do not use the all keyword, the next hop of only eBGP-learned routes is updated by the route reflector.
PAGE 396
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. This command automatically restarts the neighbor session for the configuration to take effect. Configure the same password on both BGP peers or a connection does not occur.
PAGE 397
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the dmzlink-bw parameter. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 398
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 399
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced the limit keyword on the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 400
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. To accept 4-byte formats before entering a 4 byte AS Number, configure your system.
PAGE 401
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Applies to EBGP neighbors only. Configure your system to accept 4-byte formats before entering a 4 byte AS Number. If the AS-PATH contains both public and private AS number or contains AS numbers of an EBGP neighbor, the private AS numbers are not removed.
PAGE 402
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted.
PAGE 403
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector, the internal BGP (IBGP) speakers in the network must be fully meshed.
PAGE 404
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To configure a COMMUNITY attribute, use the set community command in ROUTE-MAP mode.
PAGE 405
Related Commands ● bgp client-to-client reflection — enable route reflection between the route reflector and the clients. neighbor shutdown Disable a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} shutdown To enable a disabled neighbor or peer group, use the neighbor {ip-address | peer-groupname}no shutdown command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 406
neighbor soft-reconfiguration inbound Enable soft-reconfiguration for BGP. Syntax neighbor {ip-address | peer-group-name} soft-reconfiguration inbound To disable, use the no neighbor {ip-address | peer-group-name} softreconfiguration inbound command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to disable or enable all routers within the peer group.
PAGE 407
neighbor timers Set keepalive and hold time timers for a BGP neighbor or a peer group. Syntax neighbor {ip-address | peer-group-name} timers keepalive holdtime To return to the default values, use the no neighbor {ip-address | peer-group-name} timers command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to set the timers for all routers within the peer group.
PAGE 408
neighbor timers extended Set idle hold time for a BGP neighbor or a peer group. Syntax neighbor {ip-address | ipv6-address | peer-group-name} timers extended idle holdtime To return to the default values, use the no neighbor {ip-address | ipv6-address | peergroup-name} timers extended idle holdtime command. Parameters ip-address Enter the IP address of the peer router in dotted decimal format. ipv6-address Enter the IPv6 address of the peer router in X:X:X:X::X format.
PAGE 409
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 410
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In the Dell EMC Networking OS best path selection process, the path with the highest weight value is preferred.
PAGE 411
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 412
Command Modes ROUTER BGP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 413
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. ● deny bandwidth – link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. redistribute Redistribute routes into BGP. Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command.
PAGE 414
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
PAGE 415
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 416
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. At least one interface must be in Layer 3 mode for the router bgp command to be accepted.
PAGE 417
9.11.0.0 Usage Information Introduced on the S-Series, Z-Series, MXL, and IOM. You can use this command to disable all the configured BGP neighbors corresponding to the multicast IPv4 address families. This command is global for all VRFs. shutdown address-family-ipv4–unicast Disables all the BGP neighbors corresponding to the unicast IPv4 address families.
PAGE 418
Defaults N/A Command Modes ROUTER MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 419
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced. Example DellEMC(conf-router_bgp)# show capture bgp-pdu neighbor 20.20.20.2 Incoming packet capture enabled for BGP neighbor 20.20.20.
PAGE 420
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Example DellEMC(conf-router_bgp)# show config ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.
PAGE 421
community-list community-listname (OPTIONAL) Enter the keyword community-list then the community–list– name to display the routes matching the community–list. dampened-paths (OPTIONAL) Enter the keyword dampened-paths to display the paths suppressed due to dampening. extcommunitylist list name (OPTIONAL) Enter the keyword extcommunity-list then the list name to display the routes matching the extended community-list.
PAGE 422
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. In BGP, this command displays the exact reason why the route is discarded.
PAGE 423
Following is the example for displaying all the received routes from all IPv4 neighbors: DellEMC# show ip bgp vrf test ipv4 unicast neighbors all received-routes BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 1.1.1.
PAGE 424
● show ip bgp flap-statistics — view flap statistics on BGP routes. ● show ip bgp neighbors — allow you to view the information BGP neighbors exchange. ● show ip bgp next-hop — view all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. ● show ip bgp paths — view all the BGP path attributes in the BGP database.
PAGE 425
Usage Information Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned.
PAGE 426
communitynumber Enter the community number in AA:NN format where AA is the AS number (2 bytes) and NN is a value specific to that autonomous system. You can specify up to eight community numbers to view information on those community groups. local-AS Enter the keywords local-AS to view all routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED. All routes with the NO_EXPORT_SUBCONFED (0xFFFFFF03) community attribute must not be advertised to external BGP peers.
PAGE 427
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 428
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 429
AS_PATH : 200 Next-Hop : 172.16.0.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref Communities : 200:1 1000:1 DellEMC# 100, Weight 0, external 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active).
PAGE 430
Usage Information To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized. The history paths that the show ip bgp command displays contain only the prefix and the next-hop information.
PAGE 431
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 432
show ip bgp extcommunity-list View information on all routes with Extended Community attributes. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] extcommunity-list [list name] Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information on all routes with extended community attributes corresponding to that VRF.
PAGE 433
Example DellEMC# show run extcommunity-list ! ip extcommunity-list ecl1 permit rt 100:4 permit soo 40:4 DellEMC#show ip bgp extcommunity-list ecl1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 434
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp filter-list hello command shown in the following example.
PAGE 435
ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. ip-address (OPTIONAL) Enter the IP address (in dotted decimal format) of the BGP network to view information only on that network. mask (OPTIONAL) Enter the network mask (in slash prefix (/x) format) of the BGP network address.
PAGE 436
Usage Information Example The following describes the show ip bgp flap command shown in the following example. Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route. Flaps Displays the number of times the route flapped. Duration Displays the hours:minutes:seconds since the route first flapped. Reuse Displays the hours:minutes:seconds until the flapped route is available.
PAGE 437
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp inconsistent-as command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route.
PAGE 438
*>I 55.55.66.66/32 *>a 66.66.0.0/16 *>n 66.66.66.77/32 *>n 66.66.77.77/32 DellEMC# 72.1.1.2 0.0.0.0 0.0.0.0 0.0.0.0 0 0 0 100 0 32768 32768 32768 i i i i show ip bgp neighbors Allows you to view the information BGP neighbors exchange.
PAGE 439
Usage Information Version Description 9.14(0.0) Introduced the [all] option for IPv4 and IPv6 neighbors. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.0.2.
PAGE 440
The Lines Beginning with: Description ● keepalive interval is the number of seconds between keepalive messages to help ensure that the TCP session is still alive. Received messages This line displays the number of BGP messages received, the number of notifications (error messages), and the number of messages waiting in a queue for processing.
PAGE 441
Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last res
PAGE 442
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop.
PAGE 443
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 444
show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Syntax show ip bgp [vrf vrf-name] paths community Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 444 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 445
show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]] vrf vrf-name (OPTIONAL) Enter the keyword vrf to view information on BGP peers in a peer group corresponding to that VRF. NOTE: You can use this attribute to view information on BGP peers in a peer group that correspond to either a default or a non-default VRF.
PAGE 446
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp peer-group command shown in the following example. Line beginning Description with: Example Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported.
PAGE 447
● * = (asterisk) the sequences in a pattern (zero or more sequences). ● + = (plus) the sequences in a pattern (one or more sequences). ● ? = (question mark) sequences in a pattern (either zero or one sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element. { } = (braces) minimum and the maximum match count.
PAGE 448
Example DellEMC# show ip bgp regexp ^200 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 55.0.0.0/24 *> 66.0.0.0/24 DellEMC# Next Hop 172.16.0.2 172.16.0.
PAGE 449
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes. For example, if cluster_id is an attribute associated with thousand routes that contain exactly the same set of attributes, then the cluster_id count is 1.
PAGE 450
Field State/Pfxrcd Description Time Established Display Example < 1 day 00:12:23 (hours:minutes:seconds) < 1 week 1d21h (DaysHours) > 1 week 11w2d (WeeksDays) If the neighbor is in Established stage, the number of network prefixes received. If a maximum limit was configured with the neighbor maximum-prefix command, (prfxd) appears in this column. If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm).
PAGE 451
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. DellEMC# show running-config bgp ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC# timers bgp Adjust the BGP Keep Alive and Hold Time timers.
PAGE 452
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. timers bgp extended Adjust the BGP idle holdtime for all the BGP neighbors. Syntax timers bgp extended idle-holdtime To return to the default, use the no timers bgp extended command.
PAGE 453
debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 454
To return to default values, use the no distance bgp command. Parameters external-distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internal-distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200. local-distance Defaults Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255.
PAGE 455
ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 456
n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network d From 55.0.0.0/24 172.16.0.2 Reuse Path 00:36:23 200 DellEMC# BGP Extended Communities (RFC 4360) BGP Extended Communities, as defined in RFC 4360, is an optional transitive BGP attribute. BGP Extended Communities provides two major advantages over Standard Communities: ● The range is extended from 4-octet (AA:NN) to 8-octet (Type:Value) to provide enough number communities.
PAGE 457
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Usage Information If the set community rt and soo are in the same route-map entry, the behavior defines as: ● If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. ● If the rt option comes after soo, without the additive option, rt overrides the communities soo sets.
PAGE 458
Usage Information If the set community rt and soo are in the same route-map entry, the behavior defines as: ● If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. ● If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. ● If the rt with the additive option comes after soo, rt adds the communities soo sets.
PAGE 459
show ip extcommunity-list Display the IP extended community list. Syntax Parameters show ip extcommunity-list [word] word Enter the name of the extended community list you want to view. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 460
as-number Clear and reapply policies for all neighbors belonging to the AS. The range is from 0 to 65535 (2 Byte), from 1 to 4294967295 (4 Byte), or from 0.1 to 0.65535.65535 (Dotted format). ipv4-neighboraddr | ipv6neighbor-addr Clear and reapply policies for a neighbor. peer-group name Clear and reapply policies for all BGP routers in the specified peer group. ipv6 unicast Clear and reapply policies for all IPv6 unicast routes. in Reapply only inbound policies.
PAGE 461
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Added support for IPv4 multicast and IPv6 unicast routes. 7.8.1.0 Introduced on the S4810. 7.7.1.
PAGE 462
Parameters ipv4-address | ipv6-address Enter the IP address of the neighbor for which you want to start storing inbound routing updates. peer-group-name Enter the name of the peer group for which you want to start storing inbound routing updates. Defaults Disabled. Command Modes ROUTER BGPv6 ADDRESS FAMILY (conf-router_bgpv6_af) Command History Usage Information This guide is platform-specific.
PAGE 463
Related Commands ● ipv6 prefix-list — configure an IPv6 prefix-list. IPv6 MBGP Commands Multiprotocol BGP (MBGP) is an enhanced BGP that enables the multicast routing policy throughout the internet and connecting multicast topologies between BGP and autonomous systems (AS). FTOS MBGP is implemented as per IETF RFC 1858. show ipv6 mbgproutes Display the selected IPv6 MBGP route or a summary of all MBGP routes in the table.
PAGE 464
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 465
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● IPV6Acl : 0 IPV4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 nlbclusteracl: 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 ipv4udfmirracl: 0 vrfv4Acl :0 Openflow : 0 fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 8.
PAGE 466
fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The range is from 0 to 6. Iscsioptacl Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2. number ipv4udfmirracl Enter the keyword ipv4udfmirracl and then the number of FP blocks for IPv4 UDF mirror ACL. The range is from 0 to 8. ipv4mirracl Enter the ipv4mirracl keyword and then the number of FP blocks for IPv4 mirror ACL. The range is from 0 to 8.
PAGE 467
The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only number of blocks can be configured by the user . If allocation values are not entered for the CAM regions, the value is 0. If you enable BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the command reload conditional nvram-cfg-change. cam-acl-egress Allocate CAM for egress ACLs.
PAGE 468
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 469
Command History Usage Information Example Version Description 9.14.1.0 Introduced on the S4810 and S4820T. 9.13.0.0 Introduced on the MXL, FN IOM, S5000, S4048-ON, S6000, S6000-ON, S3048ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. The no cam-threshold command will set the CAM threshold to 90 percent and silence period to 0. The CAM threshold and silence period configuration is applicable only for Ingress L2, IPv4, IPv6 and Egress L2, IPv4, and IPv6 ACL CAM groups.
PAGE 470
Example DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p
PAGE 471
IPV6(IPV4QOS) Triple Wide Regions: VmanQos, Openflow, ipv4udfmirracl L2Acl : 2 Ipv4Acl : 4 Ipv6Acl* : 2 Ipv4Qos* : 0 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl: 0 ipv4mirracl : 0 * - shared regions show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow) Syntax Parameters Defaults show
PAGE 472
Table 3.
PAGE 473
| | IN-V6 ACL | | IN-L3-MIRR ACL | | IN-L3 FIB | 0 | 0 | 0 | 0 | 0 | 0 | 163840 | 15 | 163825 test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax Parameters Defaults test cam-usage service-policy input input policy name stack-unit {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters.
PAGE 474
Example Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks. Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for stack-units and port-pipes in the chassis. The port set value is from 0 to 0. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile.
PAGE 475
The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.. Usage Information This command takes effect only after reboot. Related Commands show hardware forwarding-table mode — displays the hardware forwarding table mode in the current boot and in the next boot.
PAGE 476
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 477
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax Parameters Defaults service-policy rate-limit-cpu-queues policy-name policy-name Enter the service-policy name, using a string up to 32 characters. Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History Usage Information This guide is platform-specific.
PAGE 478
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 479
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload.
PAGE 480
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 481
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 482
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 483
LLDP GVRP STP ISIS DellEMC# any 01:80:c2:00:00:21 01:80:c2:00:00:00 01:80:c2:00:00:14/15 09:00:2b:00:00:04/05 0x88cc any any any any Q8 Q8 Q7 Q9 Q9 CP CP CP CP CP _ _ _ _ Control Plane Policing (CoPP) 483
PAGE 484
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 485
Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 486
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 487
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release.
PAGE 488
Usage Information ● When you configure lossless queues on an interface, PFC priority configuration is not allowed on the dcb-map profile applied on the interface. ● The maximum number of lossless queues globally supported on the switch is two. The following lists the dot1p priority-queue assignments.
PAGE 489
show interface pfc Displays the PFC configuration applied to ingress traffic on an interface, including priorities and link delay. Syntax Parameters show interface port-type slot/port[/subport] pfc {summary | statistics | detail | buffer-threshold} port-type slot/ port[ /subport ] pfc Enter the port-type slot and port PFC information. Enter the subport number if a port is fanned-out into 10G ports.
PAGE 490
Field Description from peers; received PFC configuration take effect. The admin operational status for a DCBX exchange of PFC configuration is enabled or disabled. 490 Remote is enabled, Priority list Remote Willing Status is enabled Operational status (enabled or disabled) of peer device for DCBX exchange of PFC configuration with a list of the configured PFC priorities. Willing status of peer device for DCBX exchange (Willing bit received in PFC TLV): enabled or disable.
PAGE 491
Example (Summary) Field Description PFC TLV Statistics: Error pkts Number of PFC error packets received. PFC TLV Statistics: Pause Tx pkts Number of PFC pause frames transmitted. PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
PAGE 492
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 493
Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 494
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default, equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure bandwidth amounts in associated dot1p queues, use the bandwidth-percentage command.
PAGE 495
dcb-enable Enable data center bridging. Syntax dcb enable[pfc-queues 1–4] To disable DCB, use the no dcb enable command. Parameters Defaults pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 496
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. priority-list Configure the 802.1p priorities for the traffic on which you want to apply an ETS output policy. Syntax priority-list value To remove the priority list, use the no priority-list command. Parameters Defaults value Enter the priority list value.
PAGE 497
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. If an error occurs in an ETS output-policy configuration, the configuration is ignored and the scheduler and bandwidth allocation settings are reset to the ETS default values (all priorities are in the same ETS priority group and bandwidth is allocated equally to each priority).
PAGE 498
Related Commands ● qos-policy-output ets — configure the ETS bandwidth allocation. ● bandwidth-percentage — bandwidth percentage allocated to priority traffic in port queues. show interface ets Displays the ETS configuration applied to egress traffic on an interface, including priority groups with priorities and bandwidth allocation.
PAGE 499
-----------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status i
PAGE 500
TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts DellEMC# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 M
PAGE 501
Traffic Class TLV Tx Status is disabled 0 Input Conf TLV Pkts, 0 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0T LIVnput Traffic Class TLV Pkts, 0 Output Traffic Class TLV Pkts, 0 Error Traffic Class Pkts Example (Detail) DellEMC(conf)# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0%
PAGE 502
show qos priority-groups Displays the ETS priority groups configured on the switch, including the 802.1p priority classes and ID of each group. Syntax show qos priority-groups Command Modes EXEC Privilege Command History Example (Summary) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 503
TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - Stack unit 2 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 - DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS.
PAGE 504
advertise dcbx-appln-tlv On a DCBX port with a manual role, configure the application priority TLVs advertised on the interface to DCBX peers. Syntax advertise dcbx-appln-tlv {fcoe | iscsi} To remove the application priority TLVs, use the no advertise dcbx-appln-tlv {fcoe | iscsi} command. Parameters Defaults {fcoe | iscsi} Enter the application priority TLVs, where: ● fcoe: enables the advertisement of FCoE in application priority TLVs.
PAGE 505
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. You can configure the transmission of more than one TLV type at a time; for example: advertise dcbx-tlv ets-conf ets-reco.
PAGE 506
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command.
PAGE 507
debug dcbx Enable DCBX debugging. Syntax debug dcbx {all | auto-detect-timer | config-exchng | fail | mgmt | resource | sem | tlv} To disable DCBX debugging, use the no debug dcbx command. Parameters Defaults {all | autodetect-timer | config-exchng | fail | mgmt | resource | sem | tlv} Enter the type of debugging, where: ● all: enables all DCBX debugging operations. ● auto-detect-timer: enables traces for DCBX auto-detect timers. ● config-exchng: enables traces for DCBX configuration exchanges.
PAGE 508
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. This command is available at the global level only.
PAGE 509
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 510
Field Description Local DCBX TLVs Transmission status (enabled or disabled) of advertised DCB TLVs (see TLV code Transmitted at the top of the show command output). Local DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs. Local DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs. Local DCBX Sequence number transmitted in Control TLVs. Status: Sequence Number Local DCBX Acknowledgement number transmitted in Control TLVs.
PAGE 511
F-Application priority for FCOE enabled f-Application Priority for FCOE disabled I-Application priority for iSCSI enabled i-Application Priority for iSCSI disabled ----------------------------------------------------------Interface TenGigabitEthernet 1/9 Remote Mac Address 00:00:00:00:00:11 Port Role is Auto-Upstream DCBX Operational Status is Enabled Is Configuration Source? TRUE Local DCBX Compatibility mode is CEE Local DCBX Configured mode is CEE Peer Operating version is CEE Local DCBX TLVs Transmitted
PAGE 512
Usage Information A DCB map is a template used to configure DCB parameters and apply them on converged Ethernet interfaces. DCB parameters include priority-based flow control (PFC) and enhanced traffic selection (ETS). To display the PFC and ETS settings in DCB maps, enter the show qos dcb-map name command. Use the dcb-map command to create a DCB map to specify PFC and ETS settings and apply it on Ethernet ports.
PAGE 513
● Priority group 4 contains traffic with dot1p priority 5, 6, and 7. To remove a priority-pgid configuration from a DCB map, enter the no priority-pgid command. For PFC enabled priorities, it is recommended to map single priority per Priority group. pfc mode on Enable the PFC configuration on the port so that the priorities are included in DCBX negotiation with peer PFC devices. Syntax pfc mode on To disable the PFC configuration, use the no pfc mode on command. Defaults PFC mode is on.
PAGE 514
pfc {on | off} Defaults Configure whether priority-based flow control is enabled (on) or disabled (off) for port traffic in the priority group. None Command Modes DCB MAP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 515
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810 and S6000 platforms.
PAGE 516
Example Dell# show qos dcb-map dcbmap2 State :Complete PfcMode:ON -------------------PG:0 TSA:ETS BW:50 PFC:OFF Priorities:0 1 2 4 5 6 7 PG:1 TSA:ETS Priorities:3 BW:50 PFC:ON dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. Syntax dcb pfc-shared—buffer—size buffer-size Parameters Default buffer-size Enter a number in the range of 0 to 7787. The default is 832KB.
PAGE 517
dcb-buffer-threshold Configure the profile name for the DCB buffer threshold. Syntax Parameters Default dcb buffer—threshold profile-name profile-name Enter the name of the profile, which can be a string of up to 32 characters in length. None Command Modes CONFIGURATION mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 518
size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 45 KB. pause-threshold Buffer limit for pause frames to be sent. NOTE: In addition to the specified pause-threshold value, pause frames are sent only when the buffer usage exceeds some percentage of the shared buffer. threshold-value Buffer limit at which the port sends the pause to peer in KB. Enter a number in the range of 0 to 7787. The default is 10 KB.
PAGE 519
qos-policy-buffer Create a QoS policy buffer and enter the configuration mode to configure the no-drop queues, ingress buffer size, buffer limit for pausing, and buffer offset limit for resuming.
PAGE 520
For each QoS policy buffer, you can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets. When PFC detects congestion on a queue for a specified priority, it sends a pause frame for the 802.1p priority traffic to the transmitting device. You can use set up both the administrative and peer-related PFC priorities.
PAGE 521
dcb-policy buffer-threshold (Global Configuration) Assign the dcb buffer threshold policy on the stack ports. To apply the dcb buffer threshold policy on the stack-units, use the configuration mode. To apply on front-end ports, use the interface mode.
PAGE 522
Example Field Description Name Name of the DCB buffer threshold profile Buffer threshold parameters Buffer size allocated for the PFC priority queue and the priority of the queue Dell# show qos dcb buffer-threshold Name : test1 Buffer threshold parameters: pfc priority 0 buffer-size 40 pfc priority 3 buffer-size 50 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 523
Example DellEMC(conf)#dcb pfc-total-buffer-size 2800 DellEMC(conf)# DellEMC#show dcb DCB Status: Enabled, PFC Queue Count: 2 Total Buffer: Total available buffer excluding the buffer pre-allocated for guaranteed services like global headroom, queue's min guaranteed buffer and CPU queues. PFC Total Buffer: Maximum buffer available for lossless queues. PFC Shared Buffer: Buffer used by ingress priority groups for shared usage.
PAGE 524
Example Field Description resumethreshold-value Buffer offset limit at which the port resumes the peer in KB.
PAGE 525
sharedSpecify the weight of a queue for the shared buffer space threshold-weight queue 0 to queue To apply the shared-threshold weight, specify the queue number 7 number Default Enter a weight for the queue on the shared buffer as a number in the range of 1 to 11. The default threshold weight on the shared buffer for each queue is 9. Therefore, each queue can consume up to 66.67 percent of available shared buffer by default.
PAGE 526
dcb pfc-queues Configure the number of PFC queues. Syntax dcb pfc-queues value Parameters Default value Enter the number of PFC queues in the range of 0 through 4. The number of ports supported based on lossless queues configured will depend on the buffer. The default number of PFC queues in the system is 2 for S4810 and 1 for S6000 platforms. Command Modes CONFIGURATION mode Command History This guide is platform-specific.
PAGE 527
Usage Information PFC and ETS are enabled by default on the interfaces when DCB is globally enabled (refer to dcb enable). In some network topology, you may want to disable PFC on an interface and apply link level flow control; Similarly you may want to disable ETS on an interface and apply QoS bandwidth configurations. Limitations ● “dcb-map” CLI on interface is mutually exclusive to “no dcb ets enable” and “no dcb pfc enable”. ● “pfc priority” CLI is mutually exclusive to “no dcb pfc enable” command.
PAGE 528
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 529
is not reachable, the application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
PAGE 530
no-reboot Defaults Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit stack-unit-number command. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 531
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process.
PAGE 532
Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 533
Related Commands Version Description 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. ● show hardware stack-unit — display the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
PAGE 534
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 535
show hardware mac Display MAC ACL entries for the specified stack-unit, port-pipe and pipeline ID. Syntax Parameters Defaults show hardware mac {eg-acl | in-acl} stack-unit id port-set 0–0 eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack- unit id Enter the keyword stack-unit to select the stack unit ID.
PAGE 536
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 537
Defaults drops [unit unitnumber ] Enter the keyword drops to display internal drops on the selected stack member. Enter the optional keyword unit unit-number to display the internal drop counters of the specified port pipe. fpga register Enter the keyword to display the register value of the fpga register.
PAGE 538
0 Multicasts, 3 Broadcasts, 322 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec Output 00.
PAGE 539
0x0060a04c ASFPORTSPEED.ge10 = 0x00000000 0x0060b04c ASFPORTSPEED.ge11 = 0x00000000 0x0060c04c ASFPORTSPEED.ge12 = 0x00000000 0x0060d04c ASFPORTSPEED.ge13 = 0x00000000 0x0060e04c ASFPORTSPEED.ge14 = 0x00000000 0x0060f04c ASFPORTSPEED.ge15 = 0x00000000 0x0061004c ASFPORTSPEED.ge16 = 0x00000000 0x0061104c ASFPORTSPEED.ge17 = 0x00000000 0x0061204c ASFPORTSPEED.ge18 = 0x00000000 0x0061304c ASFPORTSPEED.ge19 = 0x00000000 0x0061404c ASFPORTSPEED.ge20 = 0x00000000 0x0061504c ASFPORTSPEED.
PAGE 540
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 540 - Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byt
PAGE 541
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority PFC Frame Priority Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter 8 Debug Counter 9 Debug Counter 10 Debug Counter 11 3 4 5 6 7 --------------------unit: 0 port: 61 (interface Fo 1/60) Description RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX
PAGE 542
RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - Debug Counter 6 Debug Counter 7 Debug Counter 8 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Fra
PAGE 543
****************************************************** Link Status of all the ports in the Device - 1 The linkStatus of Front End Port 0 is FALSE The linkStatus of Front End Port 1 is FALSE The linkStatus of Front End Port 2 is FALSE The linkStatus of Front End Port 3 is FALSE The linkStatus of Front End Port 4 is FALSE The linkStatus of Front End Port 5 is FALSE The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus
PAGE 544
Related Commands ● clear hardware system-flow — clear the statistics from selected hardware components. ● show interfaces stack-unit — display information on all interfaces on a specific S-Series stack member. ● show processes cpu (S-Series) — display the CPU usage information based on the processes running in an S-Series. ● show system — display the current status of all the stack members or a specific member.
PAGE 545
2036 VRRP STUB 2035 L2_DST_HIT+BC MAC+VLAN 4095 2034 L2_DST_HIT+BC MAC 2033 Catch all 384 OSPF[224.0.0.5] Packets 383 OSPF[224.0.0.
PAGE 546
show hardware vlan-counters Display the hardware VLAN statistics. Syntax show hardware vlan-counters vlan-id Parameters Defaults vlan-id Enter the interface VLAN number. The range is from 1 to 4094. None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 547
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 548
show hardware drops Displays internal drops on the specified interface or for a range of interface. Syntax show hardware drops interface interface Parameters drops Enter the keyword drops to display internal drops. interface Enter any of the following keywords and the interface or interface range information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 549
Example displaying internal drops DellEMC# show hardware drops interface tengigabitethernet 2/1 Drops in Interface Te 2/1: --- Ingress Drops --Ingress Drops IBP CBP Full Drops PortSTPnotFwd Drops IPv4 L3 Discards Policy Discards Packets dropped by FP (L2+L3) Drops Port bitmap zero Drops Rx VLAN Drops --- Ingress MAC counters--Ingress FCSDrops Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DR
PAGE 550
buffer-statssnapshot unit number buffer-info Display the historical snapshot of buffer statistical values unit Enter the keyword unit along with a port-pipe number. The range is from 0 to 0.
PAGE 551
3 4 5 6 7 7 6 4 3 0-2,5 0 0 0 0 0 0 0 0 0 0 show hardware buffer interface Display buffer statistics for a specific interface. Syntax Parameters show hardware buffer interface interface{priority-group { id | all } | queue { id| all} ] buffer-info interface interface Enter any of the following keywords and slot/port[/subport] or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 552
DellEMC# Example displaying queue range show hardware buffer-stats-snapshot Displays buffer statistics tracking resource information for a specific interface.
PAGE 553
snapshot for both unicast and multicast packets for the specific interface Example displaying egress queue-level snapshot for unicast packets for the specific interface Unit 1 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 UCAST 10 0 UCAST 11 0 MCAST 0 0 MCAST 1 0 MCAST 2 0 MCAST 3 0 MCAST 4 0 MCAST 5 0 MCAST 6
PAGE 554
--------------------------------------MCAST 0 0 MCAST 1 0 MCAST 2 0 MCAST 3 0 MCAST 4 0 MCAST 5 0 MCAST 6 0 MCAST 7 0 MCAST 8 0 Example displaying ingress prioritygroup level snapshot for the specific interface DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 priority-group 7 Unit 1 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------7 0 0 DellEMC# show hardware buffer-stats-snapshot re
PAGE 555
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 556
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP.
PAGE 557
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 558
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific.
PAGE 559
Parameters Defaults address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 560
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. excluded-address Prevent the server from leasing an address or range of addresses in the pool.
PAGE 561
hardware-address For manual configurations, specify the client hardware address. Syntax Parameters Defaults hardware-address address address Enter the hardware address of the client. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 562
Usage Information When you upgrade the Dell EMC Networking OS from an earlier version to 9.14.1.3 or later, the system converts the DHCP CONFIGURATION host command in the running configuration to the hostaddress command. If you downgrade the Dell EMC Networking OS from version 9.14.1.3 or later to an earlier version, any existing host-address command is deleted from the running configuration. If you want to create manual DHCP bindings, use the host command. ip dhcp server Enable DHCP server globally.
PAGE 563
Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 564
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell EMC Networking recommends specifying clients as hybrid.
PAGE 565
network Specify the range of addresses in an address pool. Syntax Parameters Defaults network network /prefix-length network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 566
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 567
show ip dhcp configuration Display the DHCP configuration. Syntax Parameters Defaults show ip dhcp configuration [global | pool name] pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. None Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 568
show ip dhcp conflict Display the address conflict log. Syntax show ip dhcp conflict address Parameters Defaults address Display a particular conflict log entry. None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 569
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms.
PAGE 570
Related Commands ● arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table. arp inspection-limit Configure dynamic ARP inspection rate-limit to verify the rate of ARP packet received in a port on a specific interval. Syntax arp inspection-limit {rate pps [interval seconds]} Defaults None Command Modes INTERFACE CONFIGURATION Parameters Command History rate pps Enter the keyword rate then the packet per second (pps) value.
PAGE 571
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. ● arp inspection — enable dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. Syntax Parameters clear ip dhcp snooping {binding | source-address-validation discardcounters [interface interface]} binding Clears the binding table.
PAGE 572
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 573
ip dhcp relay Enable Option 82. Syntax Parameters Defaults ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82. remote-id port Enter the keywords remote-id port to configure the port as the remote id in option–82.
PAGE 574
ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 575
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ipv6 dhcp snooping vlan Enable ipv6 DHCP Snooping on VLAN or range of VLANs.
PAGE 576
Defaults interface type Enter the keyword interface then the type of interface to which the host is connected: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. lease time Enter the keyword lease then the amount of time the IP address are leased. The range is from 1 to 4294967295.
PAGE 577
To delete the DHCP snooping binding entry from DHCP snooping database, use the [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease valuecommand. Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IPv6 address. vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 578
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 579
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 580
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 581
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp source-address-validation Enable the IP Source Guard.
PAGE 582
Usage Information Version Description 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system. ip dhcp relay information-option Enable Option 82.
PAGE 583
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series. DellEMC(conf)# ip dhcp relay information-option vpn ip dhcp relay source-interface Configure IPv4 DHCP relay source interface.
PAGE 584
Related Commands Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. ● ipv6 dhcp relay source-interface— Configure DHCP relay source IPv6 interface. ipv6 dhcp relay source-interface Configure DHCP relay source IPv6 interface.
PAGE 585
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 586
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command.
PAGE 587
ipv6-address Default Enter the keywordipv6–address through which the server address can be reached. Disabled. Command Modes INTERFACE Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Enhanced to support non-default VRF configuration for DHCPv6 helper address. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 588
● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 589
Total cam count 5 permit host 0.0.0.0 permit vlan 10 host permit vlan 10 host permit vlan 10 host host 00:00:00:00:00:00 count (0 packets) 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) NOTE: The output for port-channel interfaces does not display the physical interface.
PAGE 590
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. DellEMC# show ipv6 dhcp snooping IPv6 DHCP Snooping IPv6 DHCP Snooping Mac Verification : Enabled. : Disabled.
PAGE 591
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Use this command to associate the system with one or more DNS servers.
PAGE 592
Usage Information Example Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. DellEMC(conf)# ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 593
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrfname] name ip-address command.
PAGE 594
Defaults None Command Modes EXEC Command History Usage Information Example 594 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.
PAGE 595
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • • • • • ecmp-group hash-algorithm hash-algorithm ecmp hash-algorithm seed ip ecmp-group ip ecmp weighted link-bundle-monitor enable link-bundle-distribution trigger-threshold show config show link-bundle distribution ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
PAGE 596
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID.
PAGE 597
● xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 ● xor16: Use CR16 — 16 bit XOR hg { crc16 | crc16cc | Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices: crc32MSB | ● crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) crc32LSB | xor1 | ● crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial xor2 | xor4 | xor8 ● crc32MSB: Use CRC32_UPPER — MSB 16 bits of computed CRC32 |
PAGE 598
Usage Information Version Description 9.9(0.0) Added flow-based-hashing support for hashing on ECMP for S4820T, S6000, S4048 and Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.
PAGE 599
hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters Defaults crc-upper Uses the upper 32 bits of the key for the hash computation. The default is crclower. dest-ip Uses the destination IP for ECMP hashing. The default is enabled.
PAGE 600
Parameters Defaults seed value Enter the keyword seed then the seed value. The range is from 0 to 2,147,483,646. stack–unit slot/ port Enter the keyword stack-unit then the slot/port[subport] number. port-set number Enter the keyword port-set then the port-pipe number. The value is 0. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 601
Defaults 16 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 602
If disabled, the CLI would inform the FIB to re-program the destination prefix paths with no weights or regular ECMP.
PAGE 603
To exit from ecmp group mode, use the exit command. Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 604
show link-bundle distribution Display the link-bundle distribution for the interfaces in the bundle, type of bundle (LAG or ECMP), and the most recently calculated interface utilization (either bytes per second rate or maximum rate) for each interface. Syntax show link-bundle-distribution Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 605
16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: Topics: • • • • fips mode enable show fips status show ip ssh ssh fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes CONFIGURATION Command History Example This guide is platform-specific.
PAGE 606
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 607
SSH server ciphers : aes256-ctr, aes256-cbc, aes192-ctr, aes192cbc, aes128-ctr, aes128-cbc, 3des-cbc. SSH server macs : hmac-sha2-256, hmac-sha1, hmac-sha1-96, hmac-md5, hmac-md5-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default.
PAGE 608
● ● ● ● ● ● ● aes256–ctr: Force ssh to use the aes256–ctr encryption cipher. aes256–cbc: Force ssh to use the aes128–cbc encryption cipher. aes192–ctr: Force ssh to use the aes128–cbc encryption cipher. aes192–cbc: Force ssh to use the aes256–cbc encryption cipher. aes128–ctr: Force ssh to use the aes256–cbc encryption cipher. aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. 3des-cbc: Force ssh to use 3des-cbc encryption cipher.
PAGE 609
Usage Information Dell EMC Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. Example If FIPS mode is not enabled: DellEMC# ssh 10.10.10.
PAGE 610
17 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE end-device and an FCF.
PAGE 611
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface.
PAGE 612
info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 613
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 9.2(0.2) Introduced on the S4810 and S4820T. Added the receive parameters packettype and interfaces and their options.
PAGE 614
fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN. Syntax fip-snooping enable To disable the FIP snooping feature on all or a specified VLAN, use the no fip-snooping enable command. Defaults FIP snooping is disabled on all VLANs. Command Modes ● CONFIGURATION ● VLAN INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 615
Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. fip-snooping max-sessions-per-enodemac Configure the maximum session limit per ENode MAC address. Syntax fip-snooping max—sessions—per—enode—mac max-sessions-value To return the configured maximum sessions to the default value, use the no fip-snooping max— sessions—per—enode—mac command.
PAGE 616
Usage Information Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links. It is not recommended to use this command because multi-hop FSB is not supported.
PAGE 617
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 618
Field Description VLAN VLAN ID number the session uses. FC-ID Fibre Channel session ID the FCF assigns.
PAGE 619
------- ------------- ---- ------ -------------- ------------54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax Parameters show fip-snooping statistics [interface vlan vlan-id | interface interfacetype | interface port-channel port-channel-number] vlan-id Enter the VLAN ID of the FIP packet statistics displays.
PAGE 620
Field Description Number of ENode Number of FIP-snoop ENode keep-alive frames received on the interface. Keep Alives Number of VN Port Keep Alives Number of FIP-snoop VN port (Virtual N-port) keep-alive frames received on the interface Number of Multicast Discovery Advertisements Number of FIP-snoop multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snoop unicast discovery advertisements received on the interface.
PAGE 621
Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int tengigabitethernet 1/11 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of FLOGI :1 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :4416 Number of VN Port Keep Alive :3136 Number of Multicast Discovery Advertisement :0 Number of Unicast Discover
PAGE 622
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 623
show fips status Display the FIPs status on the platform. Syntax show fips status Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.
PAGE 624
18 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember ● ● ● ● ● ● ● FRRP is media- and speed-independent.
PAGE 625
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 626
count number Defaults Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Disabled. Command Modes CONFIGURATION (conf-frrp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 627
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol.
PAGE 628
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 629
Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration. Ownership is relinquished for a port only when the interface does not play a part in any control VLAN, that is, the interface does not belong to any ring. Related Commands ● show frrp — display the Resilient Ring Protocol configuration information. member-vlan Specify the member VLAN identification numbers.
PAGE 630
To reset the mode, use the no mode {master | transit} command. Parameters Defaults master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 631
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced This command places you into the resilient ring protocol.
PAGE 632
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command executes.
PAGE 633
● The number of state change counters Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command is executed.
PAGE 634
To remove the timer, use the no timer {hello-interval [milliseconds]}| {deadinterval milliseconds} command. Parameters hello-interval milliseconds dead-interval milliseconds Defaults Enter the keyword hello-interval then the time, in milliseconds, to set the hello interval of the control packets. The milliseconds must be entered in increments of 50 millisecond; for example, 50, 100, 150, and so on. If an invalid value is entered, an error message is generated. The range is from 50 to 2000 ms.
PAGE 635
19 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 636
• • • • show show show show config garp timers gvrp gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax clear gvrp statistics interface interface Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 637
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters Defaults config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 638
To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 639
NOTE: Designate the milliseconds in multiples of 100. Defaults As above. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 640
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 641
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 642
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series ● disable — globally disable GVRP. show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History Related Commands This guide is platform-specific.
PAGE 643
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 644
Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 645
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. summary Defaults Enter the keyword summary to display just a summary of the GVRP statistics. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 646
Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 DellEMC# Related Commands 646 ● show gvrp — display the GVRP configuration.
PAGE 647
20 High Availability (HA) High availability (HA) in the Dell EMC Networking OS is the configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol. You must specifically enable some protocols for HA.
PAGE 648
Usage Information Version Description 7.6.1.0 Introduced on the E-Series Enabling this command keeps the failed RPM in the failed state. If there are two RPMs in the system, enabling this command prevents the failed RPM from becoming a working Standby RPM. If there is only one RPM in the system, the failed RPM does not recover and affects the system. redundancy force-failover Force the secondary stack unit to become the primary stack unit.
PAGE 649
xstp Default Enter the keyword xstp to invoke hitless STP (all STP modes — MSTP, PVST+, RSTP, and STP). Disabled Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.
PAGE 650
Usage Information The following describes the show redundancy command shown in the following example. Field Description RPM Status Displays the following information: ● Slot number of the RPM. ● Whether the RPM is Primary or Standby. ● The state of the RPM: Active, Standby, Booting, or Offline. ● Whether the link to the second RPM is up or down.
PAGE 651
Auto reboot RPM: Enabled Auto failover limit: 3 times in 60 minutes -- RPM Failover Record ------------------------------------------------Failover Count: 1 Last failover timestamp: Jul 13 2007 21:25:32 Last failover Reason: User request -- Last Data Block Sync Record: ------------------------------------------------Line Card Config: succeeded Jul 13 2007 21:28:53 Start-up Config: succeeded Jul 13 2007 21:28:53 SFM Config State: succeeded Jul 13 2007 21:28:53 Runtime Event Log: succeeded Jul 13 2007 21:28:5
PAGE 652
21 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 652 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 653
Table 4. ICMP messages and their definitions (continued) Symbol Type Code Description 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 654
22 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember ● Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent sourcespecific multicast (PIM-SSM) include and exclude modes. ● IGMPv2 is the default version of IGMP on interfaces.
PAGE 655
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 656
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 657
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. The access list accepted is an extended ACL.
PAGE 658
Version Description 7.7.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion.
PAGE 659
Version Description E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters Defaults seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 660
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 661
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 662
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax ip igmp version {2 | 3} Parameters Defaults 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. 2 (IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 663
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 664
Example Example (VLT) Field Description Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. DellEMC# show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.0.2 Vlan 100 00:00:05 00:02:04 225.0.0.3 Vlan 100 00:00:05 00:02:04 225.0.0.
PAGE 665
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF. interface (OPTIONAL) Enter the interface type and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 666
Internet address is 35.0.0.1/24 IGMP is enabled on interface IGMP query interval is 60 seconds IGMP querier timeout is 125 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is enabled for all groups IGMP activity: 0 joins IGMP querying router is 35.0.0.1 (this system) IGMP version is 2 Example (VRF) DellEMC# show ip igmp vrf BLUE interface TenGigabitEthernet 1/20 Inbound IGMP access group is not set Internet address is 50.10.4.
PAGE 667
Example Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 668
Important Points to Remember for IGMP Querier ● The IGMP snooping Querier supports version 2. ● You must configure an IP address to the VLAN interface for IGMP snooping Querier to begin. The IGMP snooping Querier disables itself when a VLAN IP address is cleared, and then it restarts itself when an IP address is reassigned to the VLAN interface. ● When enabled, IGMP snooping Querier does not start if there is a statically configured multicast router interface in the VLAN.
PAGE 669
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax debug ip igmp snooping [group address | interface] ● To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. ● To disable all debugging, use the undebug all command. Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 670
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 671
Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
PAGE 672
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to GroupLeave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters Defaults milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
PAGE 673
To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Defaults Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 674
To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 675
● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. detail (OPTIONAL) Enter the keyword detail to display the IGMPv3 source information. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 676
show ip igmp snooping mrouter Display multicast router interfaces. Syntax show ip igmp snooping mrouter [vlan number] Parameters vlan number Enter the keyword vlan then the vlan number. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 677
23 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • • • Basic Interface Commands Egress Interface Selection (EIS) Commands Port Channel Commands Time Domain Reflectometer (TDR) Commands UDP Broadcast Commands ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 678
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. vrrp [ipv6 {vr-id} (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To | vr-id] clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
PAGE 679
Related Commands ● mac learning-limit — allow aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 680
dampening Configure dampening on an interface. Syntax dampening [[[[half-life] [reuse-threshold]] [suppress-threshold]] [maxsuppress-time]] Parameters Defaults half-life Enter the number of seconds after which the penalty is decreased. The penalty decreases half after the half-life period expires. The range is from 1 to 30 seconds. The default is 5 seconds. reuse-threshold Enter a number as the reuse threshold, the penalty value below which the interface state is changed to “up”.
PAGE 681
NOTE: You cannot apply dampening on an interface that is monitoring traffic for other interfaces. Example Related Commands DellEMC(conf-if-te-1/10)# dampening 20 800 4500 120 DellEMC(conf-if-te-1/10)# ● clear dampening — clear the dampening counters on all the interfaces or just the specified interface. ● show interfaces dampening — display interface dampening information. default interface Reset a physical interface to its factory default settings.
PAGE 682
DellEMC(conf)# default interface tengigabitethernet 1/5 DellEMC(conf-if-te-1/5)# show config ! interface TenGigabitEthernet 1/5 no ip address shutdown Related Commands ● show running-config – display the current configuration. description Assign a descriptive text string to the interface. Syntax description desc_text To delete a description, use the no description command. Parameters Defaults desc_text Enter a text string up to 240 characters long.
PAGE 683
● Entering a text string after the description command overwrites any previous text string that you previously configured as the description. ● The shutdown and description commands are the only commands that you can configure on an interface that is a member of a port-channel. ● Use the show interfaces description command to display descriptions configured for each interface. duplex (10/100 Interfaces) Configure duplex mode on the Management Interface interfaces where the speed is set to 10/100.
PAGE 684
encapsulation dot1q Configures lite-subinterfaces. Syntax encapsulation dot1q vlan-id To remove a previously configured lite-subinterface, use the no encapsulation dot1q vlan-id command. Parameters dot1q vlan-id Enter the keyword dot1q followed by the VLAN ID to which the host belongs. The range is from 1 to 4094. A lite subinterface is considered as a Layer 3 port property and is synchronous with the existing rules of applying Layer 2 or Layer 3 properties to an interface.
PAGE 685
Version Description 9.14(1.0) Introduced arp-inspection option. 9.14(0.0) Introduced on the platforms S4048–ON, S6100–ON, Z9100–ON, S4048T-ON, S3048–ON, S6000, S6010–ON, S5048F-ON, FN-IOM and MXL. 9.13(0.2P2) Introduced on the S3100. Usage Information This command has to be configured before the interface moves to Err-disabled state. If not, the recovery action is not performed. Related Commands errdisable recovery interval— Configure recovery timer interval for an interface.
PAGE 686
NOTE: Flow-control packets are mirrored only when flow-control rx is enabled on an interface. Defaults rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received. tx off Enter the keywords tx off so that flow control frames are not sent from this port to the connected device when a higher rate of traffic is received.
PAGE 687
When a port receives traffic at a higher rate than it can process, the frames are stored in the port buffer. As a result, buffer usage increases. When the buffer usage reaches the value specified in the “pause-threshold” argument, the port sends PAUSE frame to the connected link partner to stop sending the traffic. Eventually this reduces the buffer usage. When the buffer usage drops by the value specified in the “resume-threshold”, the port again sends a PAUSE frame with 0 as wait-time.
PAGE 688
on on off on on off off off on on off on off on on on off off on on off on off on LocNegRx off off off off LocNegTx RemNegRx RemNegTx off off off off off off off off off off off off off off off off off off on off off off on off off off off off off on on on off off on on off off on on off on on on off off on on off off on on off off on on off off on on interface Configure a physical or virtual interface on the switch.
PAGE 689
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added the support for interfaces. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 690
To delete a range of VLANs, use the following command: no interface group vlan vlanid {- vlanid} Parameters interface, interface,... Enter the keywords interface group and one of the interfaces — slot/port or VLAN number. Select the range of interfaces for bulk configuration. Spaces are not required between the commas. Comma-separated ranges can include VLANs and physical interfaces.
PAGE 691
interface loopback Configure a Loopback interface. Syntax interface loopback number To remove a loopback interface, use the no interface loopback number command. Parameters Defaults number Enter a number as the interface number. The range is from 0 to 16383. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 692
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 693
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 694
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a Tunnel interface, enter the keyword Tunnel then a number from 1 to 16383. Defaults None Command Modes CONFIGURATION CONFIGURATION TERMINAL BATCH Command History Usage Information This guide is platform-specific.
PAGE 695
Example (If atleast one port is configured) DellEMC(conf)# interface range tengigbitethernet 1/1 - 1/11, fortyGigE 3/50, tengigbitethernet 3/10 % Warning: Non-existing ports (not configured) are ignored by interface-range Example (If no ports are configured within the specified interface range) DellEMC(conf)# interface range tengigbitethernet 1/1 - 1/11, fortyGigE 3/50, tengigbitethernet 3/10 % Error: No port is configured in interface range Example (Configuration Terminal Batch Mode) DellEMC(conf-b)#i
PAGE 696
DellEMC(conf-if-range-te-3/0-5)#exit DellEMC(conf-b)#show conf interface range tengigabitethernet 3/0 - 5 mtu 4500 DellEMC(conf-b)#commit DellEMC(conf-b)#Dec 6 11:30:45 %RPM1-P:CP %CLIBATCH-6CLI_BATCH_CONFIG_IN_PROGRESS_TRAP: Batch configuration commit is in progress Dec 6 11:30:45 %RPM1-P:CP %CLIBATCH-6-CLI_BATCH_CONFIG_COMPLETE_TRAP: Batch configuration commit is success Secondary VLT Dec 6 10:43:17 %RPM1-P:CP %CLIBATCH-6CLI_BATCH_CONFIG_IN_PROGRESS_TRAP: Batch configuration commit is in progress Dec 6 10
PAGE 697
Example (Single Range) Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 698
Example (Single Range) Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 699
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Introduced on the S4810; added support for OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. For more information about VLANs and the commands to configure them, see Virtual LAN (VLAN) Commands. FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs and IP ACLs are supported.
PAGE 700
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.16.1 Introduced on the MXL 10/40GbE Switch IO Module. You can configure the interface type as CR4 with auto-negotiation enabled. If a DAC cable link is down, you can resolve the issue by setting the interface type as CR4. Auto-negotiation is disabled by default. If the CR4 optic fails to come up, use the autoneg option.
PAGE 701
Usage Information Version Description pre-Version 6.1.1.0 Introduced on the E-Series. When you configure keepalive, the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive, the system does not send keepalive packets and so the local end of a WAN link remains up even if the remote end is down. negotiation auto Enable auto-negotiation on an interface.
PAGE 702
● ● ● ● ● Forced-master Force-slave Master Slave Auto-neg Error — typically indicates that both ends of the node are configured with forced-master or forced-slave. CAUTION: Ensure that one end of your node is configured as forced-master and one is configured as forced-slave. If both are configured the same (that is, forced-master or forced-slave), the show interfaces command flaps between an auto-neg-error and forced-master/slave states.
PAGE 703
● auto-negotiation enabled speed 100 ● auto-negotiation disabled speed 100 Link Status Between Port 1 and Port 2 ● Up at 1000 Mb/s ● Up at 100 Mb/s ● Up at 100 Mb/s ● Down ● Down * You cannot disable auto-negotiation when the speed is set to 1000 or auto. monitor interface Monitor counters on a single interface or all interfaces. The screen is refreshed every five seconds and the CLI prompt disappears.
PAGE 704
Usage Information Example (Single Interface) Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. In the Example, the delta column displays changes since the last screen refresh. The following are the monitor command menu options. Key Description systest-3 Displays the host name assigned to the system.
PAGE 705
T - Increase refresh interval q - Quit Example (All Interfaces) t - Decrease refresh interval systest-3 Monitor time: 00:01:31 Refresh Intvl.
PAGE 706
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 707
portmode hybrid To accept both tagged and untagged frames, set a physical port or port-channel. A port configured this way is identified as a hybrid port in report displays. Syntax portmode hybrid To return a port to accept either tagged or untagged frames (non-hybrid), use the no portmode hybrid command. Defaults non-hybrid Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 708
DellEMC(conf-if-vl-20)# tagged tengigabitethernet 1/1 DellEMC(conf-if-vl-20)# Example Example (Vlan) DellEMC(conf-if-vl-20)# do show interfaces switchport Name: TenGigabitEthernet 1/1 802.
PAGE 709
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced The output of the show interfaces command displays the configured rate interval, along with the collected traffic data. rate-interval (Configuration Mode) Configure the traffic sampling interval for all physical and logical port-channel interfaces globally.
PAGE 710
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 711
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 712
● For a tunnel interface, enter the keyword tunnel then the tunnel ID. The range is from 1 to 16383. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. -range (Optional) Enter the range of interfaces for which you want to view the information.
PAGE 713
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.2 Included SFP and SFP+ optics power detail in the E-Series and C-Series output. 8.2.1.0 Added support for 4093 VLANs on the E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Output expanded to include SFP+ media on the C-Series. 7.6.1.0 Introduced on the S Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Changed the organization of the display output. 6.3.1.
PAGE 714
Line Description ● Number of Multicast and Broadcast packets: ○ Multicasts = number of MAC multicast packets ○ Broadcasts = number of MAC broadcast packets ● Number of runts, giants, and throttles packets: ○ runts = number of packets that are less than 64B ○ giants = packets that are greater than the MTU size ○ throttles = packets containing PAUSE frames ● Number of CRC, overrun, and discarded packets: ○ CRC = packets with CRC/FCS errors ○ overrun = number of packets discarded due to FIFO overrun condition
PAGE 715
0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 716
Internet address is 10.11.201.
PAGE 717
● show range – display all interfaces configured using the interface range command. show interfaces configured Display any interface with a non-default configuration. Syntax show interfaces configured Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 718
0 Vlans, 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 00:04:59 DellEMC# show interfaces dampening Display interface dampening information.
PAGE 719
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 720
Usage Information Version Description 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. 6.5.4.
PAGE 721
● ● ● ● Example Auto 1000MB 100MB 10MB DellEMC# show interfaces tengigabitethernet 1/1 phy Mode Control: SpeedSelection: 10b AutoNeg: ON Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete: False RemoteFault: False LinkStatus: False JabberDetect: False AutoNegotation Advertise: 100MegFullDplx: True 100MegHalfDplx: True 10MegFullDplx: False 10MegHalfDplx: True Asym Pause: False Sym Pause: False AutoNegotiation Remote Partner's Ability: 100MegFullDplx: False 100MegH
PAGE 722
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 723
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. ● For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interfacetype 1/1 - 4.
PAGE 724
Te 1/6 Te 1/7 Te 1/8 Te 1/9 Te 1/10 Te 1/11 Te 1/12 Te 1/13 Te 1/14 Te 1/15 Te 1/16 DellEMC# Down Down Up Down Down Down Down Down Down Down Down Auto Auto Auto Auto 1000 Mbit Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto --1502,1504,1506-1508,1602 -------- show interfaces switchport Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode interfaces’ IEEE 802.1Q tag status and VLAN membership.
PAGE 725
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 726
show interfaces transceiver Display the details of an installed transceiver. Syntax show interfaces [interface number] transceiver Parameters interfaces (OPTIONAL) Enter one of the following keywords and then the interface interface number information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 727
Usage Information Version Description 7.8.1.0 Output augmented with diagnostic data for pluggable media. 7.7.1.0 Removed three fields in the output: Vendor Name, Vendor OUI, and Vendor PN. 7.6.1.0 Introduced on the C-Series and S-Series. 6.5.4.0 Introduced on the E-Series.
PAGE 728
Line Description Temp Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Warning Factory-defined setting. Value can differ between SFP and SFP+. threshold TX Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 729
Line Description Temperature Low This can be either true or false, depending on the Current Temperature value Alarm Flag displayed above. Voltage Low Alarm Flag This can be either true or false, depending on the Current voltage value displayed above. Tx Bias Low Alarm Flag This can be either true or false, depending on the Tx bias current value displayed above. Tx Power Low Alarm Flag This can be either true or false, depending on the Current Tx power value displayed above.
PAGE 730
SFP 0 CheckCodeExt = 0x5b SFP 1 Diagnostic Information =================================== SFP 1 Rx Power measurement type = Average =================================== SFP 1 Temp High Alarm threshold = 95.000C SFP 1 Voltage High Alarm threshold = 3.900V SFP 1 Bias High Alarm threshold = 17.000mA SFP 1 TX Power High Alarm threshold = 0.631mW SFP 1 RX Power High Alarm threshold = 1.259mW SFP 1 Temp Low Alarm threshold = -25.000C SFP 1 Voltage Low Alarm threshold = 2.700V SFP 1 Bias Low Alarm threshold = 1.
PAGE 731
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.
PAGE 732
Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4093 VLANs on E-Series. 8.1.1.
PAGE 733
Related Commands ● ecmp-group — configure a mechanism to monitor traffic distribution. show system stack-unit fanout configured Displays the details about the fanned-out ports. Syntax Parameters show system stack-unit stack-unit-number fanout configured stack-unit stack- The stack Unit ID of the device. unit-number fanout configured Defaults Enter the keywords fanout configured to display the details about the fanned-out ports. None.
PAGE 734
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 735
Defaults 10000 Enter the keyword 10000 to set the interface’s speed to 10000 Mb/s. Autonegotiation is enabled. For more information, refer to negotiation auto. auto Enter the keyword auto to set the interface to auto-negotiate its speed. Autonegotiation is enabled. For more information, refer to negotiation auto. auto Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 736
speed (Management interface) Set the speed for the Management interface. Syntax speed {10 | 100 | 1000 | auto} To return to the default setting, use the no speed command. Parameters Defaults 10 Enter the keyword 10 to set the interface’s speed to 10 Mb/s. 100 Enter the keyword 100 to set the interface’s speed to 100 Mb/s. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s. auto Enter the keyword auto to set the interface to auto-negotiate its speed.
PAGE 737
Parameters Defaults stack-unit number Enter the port number. The range is from 1 to 6. 49,50,51,52,53,54 Command Modes CONFIGURATION Command History Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000 and S6000–ON. For the new quad port profile configuration to take effect, you must first save changes and then reload the switch.
PAGE 738
Defaults host (OPTIONAL) Enter the keyword host to set the private VLAN interface to host mode. promiscuous (OPTIONAL) Enter the keyword promiscuous to set the private VLAN interface to promiscuous mode. trunk (OPTIONAL) Enter the keyword trunk to set the private VLAN interface to trunk mode. Disabled — interface is in Layer 3 mode. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 739
Egress Interface Selection (EIS) Commands The following commands are Egress Interface Selection (EIS) commands. application Configure the management egress interface selection. Syntax application {all | application-type} To remove a management application configuration, use the no application {all | application-type} command. Parameters Defaults application-type Enter any of the following keywords: ● For DNS, enter the keyword dns. ● For FTP, enter the keyword ftp. ● For NTP, enter the keyword ntp.
PAGE 740
Parameters Defaults application-type Enter any of the following keywords: ● For HTTP, enter the keyword http. ● For ICMP, enter the keyword icmp. all Configure all applications. None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 741
Version Description 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T. management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface. Syntax management egress-interface-selection To disable and remove management egress interface selection (EIS) configurations, use the no management egress-interface-selection command.
PAGE 742
show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Syntax show management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 743
radius sflow-collector snmp ssh syslog tacacs telnet tftp : : : : : : : : 0 0 0 2 0 0 0 0 Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a Port Channel. ● The platform supports 128 port channels and 16 members per port channel.
PAGE 744
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Use the interface port-channel command to access this command.
PAGE 745
Command Modes PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 746
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series. 7.6.1.0 Introduced on S-Series. 7.5.1.0 Introduced on C-Series. pre-Version 6.2.1.0 Introduced on E-Series.
PAGE 747
Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 748
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Usage Information This feature groups two LAGs to work in tandem as a supergroup.
PAGE 749
interface Port-channel 1 no ip address shutdown DellEMC(conf-if-po-1)# show interfaces port-channel Display information on configured Port Channel groups. ` Syntax Parameters show interfaces port-channel [channel-number] [brief] [description] channel-number For a Port Channel interface, enter the keyword port-channel then a number. The range is from 1 to 128. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 750
Version Description E-Series legacy command Usage Information Example 750 Interfaces The following describes the show interfaces port-channel command shown in the following example. Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fatesharing group (“Failover-group”) is listed. Hardware is... Displays the interface’s hardware information and its assigned MAC address. Port-channel is part...
PAGE 751
Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 1218120 packets output, 100745130 bytes, 0 underruns Output 5428 Multicasts, 4 Broadcasts, 1212688 Unicasts 1216142 IP Packets, 0 Vlans, 0 MPLS 0 throttles, 0 discarded Rate info (interval 299 sec): Input 01.50Mbits/sec, 2433 packets/sec Output 00.
PAGE 752
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. source-ip address destination-ip address source-port number destination-port number source-mac address destination-mac Enter the keywords source-ip then the IP source address in IP address format. Enter the keywords destination-ip then the IP destination address in IP address format.
PAGE 753
NOTE: In the show port channel flow command output, the egress port for an unknown unicast, multicast, or broadcast traffic is not displayed.
PAGE 754
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S Series. 7.6.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The interface must be enabled to run the test or an error message is generated: DellEMC# tdr-cable-test tengigabitethernet 11/1 % Error: Interface is disabled Te 11/1.
PAGE 755
Usage Information If the TDR test has not been run, an error message is generated: %Error: Please run the TDR test first The following describes the TDR test status. Example Related Commands Status Definition OK Status: Terminated TDR test is complete, no fault is detected on the cable, and the test is terminated. Length: 92 (+/- 1) meters, Status: Shorted A short is detected on the cable. The location, in this Example is 92 meters. The short is accurate to plus or minus one meter.
PAGE 756
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series.
PAGE 757
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series. If you configure the ip helper-address command and ip udp-helper udp-port command, the behavior is that the UDP broadcast traffic with port numbers 67/68 is unicast relayed to the DHCP server per the ip helper-address configuration.
PAGE 758
ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 759
24 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: ● Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 760
● md5 — Use Message Digest 5 (MD5) authentication. ● sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. ● null — Causes an encryption policy configured for the area to not be inherited on the interface. Defaults espauthentication Enter the keywords esp-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. ● md5 — Use Message Digest 5 (MD5) authentication.
PAGE 761
Parameters Defaults name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 762
match Apply an match filter to the crypto policy. Syntax match seq-num tcp [sourceip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] To remove the match filter for the crypto map, use the no match seq-num tcp [source ip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] command. Parameters seq-num Enter the match command sequence number.
PAGE 763
session-key Specify the session keys used in the crypto policy entry. Syntax session-key {inbound | outbound} {ah spi hex-key-string | esp spi encrypt hex-key-string auth hex-key-string To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters Defaults name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec.
PAGE 764
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500.
PAGE 765
Outound ESP Auth Key : [0]:: Outound ESP Encry Key : [0]:: Match sequence Num Protocol type IP or IPv6 Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num : : : : : : : : : : : 2 tcp IP 1.1.1.1 /32 0 1.1.1.2 /32 23 DellEMC(conf-crypto-policy)# transform-set Specify the transform set the crypto policy uses.
PAGE 766
25 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 767
• • • • • • show show show show show show ip protocols ip route ip route list ip route summary ip traffic tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters Defaults vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 768
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid. You can use the vrf attribute of this command to create a static ARP entry on either a default or a non-default VRF.
PAGE 769
Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands ● show arp retries — display the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
PAGE 770
Parameters Defaults vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows. max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 771
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart. Related Commands ● show arp retries — display the configured number of ARP retries. arp timeout Set the time interval for an ARP entry to remain in the ARP cache.
PAGE 772
Version Description pre-6.2.1.1 Introduced on the E-Series. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM). Syntax clear arp-cache [vrf vrf-name | interface | ip ip-address] [no-refresh] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear the ARP cache corresponding to that VRF.
PAGE 773
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 774
clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.) Syntax clear ip fib stack-unit unit-number vrf vrf-name Parameters unit-number Enter the number of the stack unit. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all FIB entries corresponding to that VRF. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 775
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 776
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 777
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 778
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.
PAGE 779
debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 780
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series.
PAGE 781
● For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 782
Field Description UDP src= Displays the source and destination ports for the UDP packets. ICMP type= Displays the ICMP type and code. IP Fragment States that it is a fragment and displays the unique number identifying the fragment (Ident) and the offset (in 8-byte units) of this fragment (fragment offset) from the beginning of the original datagram. Example Usage Information IP: s=10.1.2.62 (local), d=10.1.2.
PAGE 783
icmp6-redirect enable Enable ICMP and ICMP6 redirects. Syntax icmp6-redirect enable Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description Legacy command Legacy command Usage Information Use this command to notify hosts on the same network that a better route is available for a specific destination.
PAGE 784
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You must be in INTERFACE mode before you add an IP address to an interface. Assign an IP address to an interface prior to entering ROUTER OSPF mode. ip directed-broadcast Enables the interface to receive directed broadcast packets.
PAGE 785
ip domain-list Configure names to complete unqualified host names. Syntax ip domain-list name To remove the name, use the no ip domain-list name command. Parameters Defaults name Enter a domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 786
ip domain-lookup To address resolution (that is, DNS), enable dynamic host-name. Syntax ip domain-lookup To disable DNS lookup, use the no ip domain-lookup command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 787
To remove the domain name, use the no ip domain-name command. Parameters Defaults name Enter one domain name to be used to complete unqualified names (that is, incomplete domain names that cannot be resolved). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 788
Parameters Defaults ip-address Enter an IP address in dotted decimal format (A.B.C.D). Not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 789
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 790
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 791
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 792
● ● ● ● ● Defaults NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
PAGE 793
ip max-frag-count Set the maximum number of fragments allowed in one packet for packet re-assembly. Syntax ip max-frag-count count To place no limit on the number of fragments allowed, use the no ip max-frag-count command. Parameters Defaults count Enter a number for the number of fragments allowed for re-assembly. The range is from 2 to 256. No limit is set on number of fragments allowed. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 794
max-number Defaults Enter the maximum number of protocol routes that a VRF RTM can hold. The range is from 0 to 7500. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(2.0) Introduced on the S3100 series. 9.4.(0.0) Introduced on the S4810 and S4820T.
PAGE 795
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell EMC Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out on all other interfaces, including the Management port. You can separately configure both IPv4 and IPv6 domain name servers.
PAGE 796
Related Commands ● show ip interface — display the interface routing status and configuration. ip route Assign a static route to the switch. Syntax ip route [vrf vrf-name] ip-address mask {ip-address | interface [ipaddress]} [distance] [name description] [permanent] [tag tag-value] [vrf vrf-name] [weight weight-value] To delete a specific static route, use the no ip route destination mask command. To delete all routes matching a certain route, use the no ip route destination mask command.
PAGE 797
vrf vrf-name Enter the keyword vrf followed by the name of the VRF. Use this VRF option after the next hop to specify which VRF the next hop belongs to. This setting is used in route leaking cases. See “R”oute Leaking VRFs” in the Virtual Routing and Forwarding (VRF) section of the Configuration guide. weight weight- Enter the keyword weight followed by a weight value. The range is from 0 to 255.
PAGE 798
● When recursive resolution is satisfied, Dell EMC Networking OS re-installs the route. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect. Also, if a path corresponding to a static route (destination) has a non-zero weight assigned to it and other paths do not have any weight configured, then regular ECMP is used for forwarding.
PAGE 799
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages. Syntax ip unreachables To disable the generation of ICMP messages, use the no ip unreachables command. Defaults Disabled.
PAGE 800
load-balance By default, for C-Series and S-Series, Dell EMC Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 801
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Added the ingress-port parameter for the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 802
Defaults | source-destmac ] ● ● ● ● tunnel [ ipv4over-ipv4 | ipv4over-gre-ipv4 | mac-in-mac ]} To use tunnel key fields in hash computation, enter the keyword tunnel then one of the parameters: ● ipv4-over-ipv4 — Use ipv4-over-ipv4 field in hash calculation. ● ipv4-over-gre-ipv4 — Use ipv4-over-gre-ipv4 field in hash calculation. ● mac-in-mac — Use mac-in-mac field in hash calculation. dest-module-id — Use dest-module-id field in hash calculation. vlan — Use vlan field in hash calculation .
PAGE 803
NOTE: The :: notation specifies successive hexadecimal fields of zeros. forwardingrouter-address Enter an IP address (dotted decimal format) or an IPv6 address (x:x:x:x::x format) of a forwarding router. managementethe Enter the keyword managementethernet for the Management interface on the rnet Primary RPM. Defaults fortyGigE Enter the keyword fortyGigE to specify a forty Gigbit Ethernet interface. vlan Enter the keyword vlan to specify a vlan interface.
PAGE 804
show arp Display the ARP table. Syntax show arp [vrf vrf-name] [interface interface | ip ip-address [mask] | macaddress mac-address [mac-address mask]] [retries] [static | dynamic] [inspection {database | statistics][summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF. NOTE: Use this attribute to start a BGP instance for either a specific address family corresponding to the default VRF or an IPv4 address family corresponding to a non-default VRF.
PAGE 805
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF and added usage information for the clear arp-cache command. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.
PAGE 806
Internet Internet Example (Private VLAN) 192.2.1.246 1 192.2.1.245 1 00:00:c0:02:01:02 00:00:c0:02:01:02 Te 2/13 Te 2/13 - CP CP NOTE: In this example, Line 1 shows community VLAN 200 (in primary VLAN 10) in a PVLAN. Line 2 shows primary VLAN 10. DellEMC# show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU --------------------------------------------------------------Internet 5.5.5.1 - 00:01:e8:43:96:5e Vl 10 pv 200 Internet 5.5.5.10 - 00:01:e8:44:99:55 Vl 10 Internet 10.1.2.
PAGE 807
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced. ● arp retries — set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. show hosts View the host table and DNS configuration.
PAGE 808
Field Description Default domain... Displays the domain name (if configured). Name/address lookup... States if DNS is enabled on the system. ● If DNS is enabled, the Name/Address lookup is domain service. ● If DNS is not enabled, the Name/Address lookup is static mapping Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address.
PAGE 809
[ecmp-group detail]] ● Enter the keyword ecmp-group detail to view the ECMP group index. ecmp-group {detail | memberinfo [detail [group-index index-number ]]} (OPTIONAL) Enter the keyword ecmp-group then one of the following keywords to filter results. ● Enter the keyword detail to view the ECMP group index. ● Enter the keyword member-info to view the member information for the ECMP group. ● Enter the keyword member-info detail to view detailed ECMP membership and n-hop information.
PAGE 810
Example DellEMC# show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port --------------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Te 3/44 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP 1.1.1.0/24 0 1 0 00:00:00:00:00:00 CP DellEMC# Example (ECMPGroup) DellEMC# show ip cam stack-unit 3 po 0 ecmp-group detail Destination EC C VId Mac-Addr Port ECMP Group-Index -------------------------------------------------------------------------1.1.
PAGE 811
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 812
The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp weighted command. Related Commands ● clear ip fib stack-unit — clear FIB entries on a specified stack-unit. ● ip ecmp weighted— enable weighted ECMP calculations. show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface.
PAGE 813
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command provides egress port information for a given IP flow. This information is useful in identifying which interface the packet follows in the case of Port-channel and Equal Cost Multi Paths. Use this command for routed packed only.
PAGE 814
Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Updated the command output to include the unicast reverse path forwarding (uRPF) status. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 815
IP unicast RPF check is not supported DellEMC# DellEMC#show ip interface vlan 1 Vlan 1 is down, line protocol is down Internet address is not set IP MTU is 1500 bytes Directed broadcast forwarding is disabled Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# Usage Information Example (Brief) The following describes the show ip interface brief command shown in the following examp
PAGE 816
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 817
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.
PAGE 818
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Regular evaluation optimization enabled/disabled added to display output. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Example DellEMC# show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.
PAGE 819
NOTE: bgp, isis, ospf, and rip. ● If you enter bgp, you can include the BGP as-number . ● If you enter isis, you can include the ISIS routing-tag. ● If you enter ospf, you can include the OSPF process-id. process-id (OPTIONAL) Specify that only OSPF routes with a certain process ID must be displayed. routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes.
PAGE 820
Field Description ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● C = connected S = static R = RIP B = BGP IN = internal BGP EX = external BGP LO = Locally Originated O = OSPF IA = OSPF inter area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes The weight for weighted ECMP route calculations is displayed for each path
PAGE 821
Route Source Active Routes Non-active Routes connected 2 0 static 1 0 Total 3 0 Total 3 active route(s) using 612 bytes R1_E600i>show ip route static ? | Pipe through a command R1_E600i>show ip route static Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------*S 0.0.0.0/0 via 10.10.91.
PAGE 822
C C 4.4.4.0/24 6.6.6.0/24 6.6.6.2, via Te 1/16 Direct, Te 1/4 Direct, Te 1/16 0/0 0/0 00:01:32 00:01:25 DellEMC(conf)#do show ip route 1.1.1.0/24 Routing entry for 1.1.1.0/24 Known via "static", distance 1, metric 0 Last update 00:05:01 ago Routing Descriptor Blocks: * 4.4.4.2, via TenGigabitEthernet 1/4 * 6.6.6.2, via TenGigabitEthernet 1/16 DellEMC(conf)# show ip route list Display IP routes in an IP prefix list.
PAGE 823
Codes:C- connected, S - static, R - RIP, B- BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated, O- OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2- OSPF NSSA external type 2, E1 - OSPF external type 1, E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.
PAGE 824
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example. Column Heading Description Route Source Identifies how the route is configured in Dell EMC Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources.
PAGE 825
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 826
Keyword Definition ...short packets The number of bytes in the packet are too small. ...bad length The length of the packet was not correct. ...no port broadcasts The incoming broadcast/multicast packet did not have any listener. ...socket full The applications buffer is full and the incoming packet are dropped. The Dell Monitoring MIB provides access to the following statistics. ● IP Statistics: Bcast: Received: Object = f10BcastPktRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.
PAGE 827
cp Enter the keyword cp to view only TCP information from the Control Processor. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 828
Field Description Sent: Displays the total number of TCP packets sent and the number of urgent packets sent. 25 control packets... Displays the number of control packets sent and the number retransmitted. 11603 data packets... Displays the number of data packets sent. 24 data packets retransmitted Displays the number of data packets resent. 355 ack.. Displays the number of acknowledgement packets sent and the number of packet delayed. 0 window probe...
PAGE 829
26 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember ● ● ● ● ● ● ● ● ● Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 830
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 831
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 832
-- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands ● cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 833
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Added the monitor option.
PAGE 834
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 835
Defaults deny Enter the keyword deny to configure a filter to drop packets meeting this condition. ospfv3 Specify that this ACL is for OSPFv3 control plane traffic All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 836
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 837
cam-acl Allocate space for IPv6 ACLs. Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: ● L3 ACL (ipv4acl): 6 ● L2 ACL(l2acl): 5 ● IPv6 L3 ACL (ipv6acl): 0 ● L3 QoS (ipv4qos): 1 ● L2 QoS (l2qos): 1 l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 838
27 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 839
Command Modes CONFIGURATION Command History Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048–ON. 9.8(0.0P2) Introduced on the S3048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can partition the LPM table to store IPv6 prefixes greater than /64 mask length.
PAGE 840
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 841
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have. Syntax maximum dynamic-routes—ipv6 limit {warn-threshold threshold-value | warningonly} To remove the limit on the maximum number of IPv6 routes used, use the no maximum dynamicroutes-ipv6 command.
PAGE 842
ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface. Syntax ipv6 address autoconfig To disable the address autoconfig operation on the management interface, use the no ipv6 address autoconfig command. Default Disabled Command Modes INTERFACE (management interface only) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 843
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1(0.0) Updated Usage Information. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 844
To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address {ipv6-address prefix-length} eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults None Command Modes CONFIGURATION Command History Usage Information Example This guide is platform-specific.
PAGE 845
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ipv6 flowlabel-zero Configure system to set the flow label field in the packets to zero. Syntax ipv6 flowlabel-zero To disable the 0 from being set in the field and allow the protocol operations to fill the field, use the no ipv6 flowlabel-zero command. Default Disabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 846
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series. ipv6 name-server Enter up to six IPv6 addresses of name servers. The order you enter the addresses determines the order of their use.
PAGE 847
ipv6 nd dad attempts To perform duplicate address detection (DAD) on an interface, configure the number of neighbor solicitation messages that are sent. Syntax ipv6 nd dad attempts {number of attempts} To restore the default value, use the no ipv6 nd dad attempts command. Parameters Default number of attempts Enter the number of attempts to be made to detect a duplicate address. The range is from 0 to 15. Setting the value to 0 disables DAD on the interface.
PAGE 848
Parameters Defaults ipv6-RDNSSaddress Enter the IPv6 Recursive DNS Server’s (RDNSS) address. You can specify up to 4 IPv6 RDNSS server addresses. lifetime Enter the lifetime in seconds. The amount of time the IPv6 host can use the IPv6 RDNSS address for name resolution. The range is 0 to 4294967295 seconds. When you specify the maximum lifetime value of 4294967295 or infinite, the lifetime does not expire. A value of 0 indicates to the host that the RDNSS address should not be used.
PAGE 849
no-rtr-address Enter the keyword no-rtr-address to exclude the full router address from router advertisements (the R bit is not set). off-link Enter the keywords off-link to advertise the prefix without stating to recipients that the prefix is either on-link or off-link. valid-lifetime | infinite Enter the amount of time that the prefix is advertised, or enter infinite for an unlimited amount of time. The range is from 0 to 4294967295. The default is 2592000.
PAGE 850
ipv6 route Establish a static IPv6 route. Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [name description] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
PAGE 851
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.2) Added the keyword name for static routes. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 852
ipv6 unicast-routing Enable IPv6 unicast routing on the device. Syntax ipv6 unicast-routing To disable unicast routing, use the no ipv6 unicast-routing command. Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
PAGE 853
NOTE: If you do not specify this option, IPv6 CAM entries corresponding to the default VRF are displayed. unit-number Enter the stack unit’s ID number. port-set Enter the keyword Port Set. summary (OPTIONAL) Enter the keyword summary to display a table listing network prefixes and the total number prefixes which can be entered into the IPv6 CAM. index (OPTIONAL) Enter the index in the IPv6 CAM.
PAGE 854
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. ● ipv6 flowlabel-zero — configure IPv6 address auto-configuration for the management interface. show ipv6 fib stack-unit View all FIB entries.
PAGE 855
show ipv6 flowlabel-zero Display the flow label zero setting. Syntax show ipv6 flowlabel-zero Default Disabled Command Modes EXEC Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 856
Defaults fortyGigE (OPTIONAL) View information for an IPv6 fortygigabitethernet interface. stack-unit id (OPTIONAL) View information for stacking. tunnel tunnel-id (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example 856 IPv6 Basics This guide is platform-specific.
PAGE 857
ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 IPv6 unicast RPF check is not supported DellEMC# DellEMC# show ipv6 interface port-channel 128 Port-channel 128 is down, line protocol is down IPV6 is enabled Link Local address: fe80::201:e8ff:fe8a:e846 Global Unicast address(es): aabb::aa11, subnet is aabb::/64 (MANUAL) Remaining lifetime: infinite Global Anycast address(es): Joined Group address(es): ff02::1 ff02::2 ff02::1:ff00:aa11 ff02::1:ff8a:e846 ND MTU is 0 ICMP redirects are
PAGE 858
ff02::1 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds ND retransmit interval is 1000 milliseconds ND hop limit is 64 DellEMC# Example (Brief) Example (Tunnel) DellEMC# show ipv6 interface brief TenGigabitEthernet 1/2 [administratively down/down] fe80::201:e8ff:fea7:497e 2002:1:2::3/96 TenGigabitEthernet 1/12 [up/up] fe80::201:e8ff:fea7:497e 100::2/64 Man
PAGE 859
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. The following describes the show ipv6 mld-host command shown in the following example. Field Description Valid MLD Packets The total number of packets received and sent from the last time the elapsed time was cleared.
PAGE 860
Defaults bgp (OPTIONAL) View information for all IPv6 BGP routes. connected (OPTIONAL) View only the directly connected IPv6 routes. isis (OPTIONAL) View information for all IPv6 IS-IS routes. list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes. static (OPTIONAL) View only routes configured by the ipv6 route command.
PAGE 861
Field Description ● ● ● ● ● ● ● ● ● ● Example (SSeries) N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes Destination Identifies the route’s destination IPv6 address. Gateway Identifies whether the route is directly connected and on which interface the route is configured.
PAGE 862
trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults None Command Modes CONFIGURATION-POLICY-MAP-IN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 863
28 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 864
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters Defaults time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 865
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 866
Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 867
ip-address (Optional) Defaults Enter the ip-address that the iSCSI monitors. The ip-address specifies the IP address of the iSCSI target. 860, 3260 Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 868
-----------------------------------------------iSCSI Targets and TCP Ports: -----------------------------------------------TCP Port Target IP Address 3260 860 Related Commands ● show iscsi session — display information about active iSCSI sessions on the switch. ● show iscsi session detailed — display detailed information about active iSCSI sessions on the switch. ● show run iscsi — show run iscsi. show iscsi session Display information about active iSCSI sessions on the switch.
PAGE 869
show iscsi session detailed Display detailed information on active iSCSI sessions on the switch. Syntax Parameters show iscsi session detailed [session isid] isid Enter the session’s iSCSi ID to display detailed information about the specified iSCSi session. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 870
Command History Related Commands 870 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 871
29 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 872
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 873
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacencycheck is enabled by default.
PAGE 874
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1.
PAGE 875
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands ● domain-password — set the authentication password for a routing domain. ● isis password — configure an authentication password for an interface.
PAGE 876
tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 877
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command.
PAGE 878
debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies. Syntax debug isis [vrf vrf-name] adj-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name]adj-packets [interface] command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details.
PAGE 879
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF. This information contains local updates tied to the VRF that you specify. This command displays the local LSP debugging details of the current unit.
PAGE 880
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 881
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced.
PAGE 882
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information.
PAGE 883
Usage Information Version Description 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. When you use this command to redistribute routes into a routing domain, the router becomes an autonomous system (AS) boundary router. An AS boundary router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one. How a metric value assigned to a default route advertises depends on the metric-style command configuration.
PAGE 884
distance Define the administrative distance for learned routes. Syntax distance weight [ip-address mask [prefix-list]] To return to the default values, use the no distance weight command. Parameters Defaults weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability. Routes with smaller values are given preference.) The default is 115.
PAGE 885
Parameters Defaults prefix-list-name Specify the prefix list to filter prefixes in routing updates. interface (OPTIONAL) Identifies the interface type and the interface following: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 886
Defaults ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number. The range is from 1 to 65535. rip (OPTIONAL) Enter the keyword rip for RIP routes. static (OPTIONAL) Enter the keyword static for user-configured routing process. Not configured.
PAGE 887
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 888
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. Usage Information The domain password is inserted in Level 2 link state PDUs (LSPs), complete sequence number PDUs (CSNPs), and partial sequence number PDUs (PSNPs).
PAGE 889
network. A flag in the Restart TLV contains restart request (RR), restart acknowledge (RA) and suppress adjacency advertisement (SA) bit flags. The ISIS graceful restart-enabled router can co-exist in mixed topologies where some routers are graceful restart-enabled and others are not. For neighbors that are not graceful restart-enabled, the restarting router brings up the adjacency per the usual methods.
PAGE 890
Parameters Defaults seconds Enter the graceful restart time in seconds. The range is from 5 to 300 seconds. The default is 30 seconds. 30 seconds Command Modes ROUTER ISIS Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 891
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 892
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart t3 Configure the overall wait time before graceful restart completes. Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command.
PAGE 893
Related Commands ● graceful-restart restart-wait — enable the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | point-to-point] command.
PAGE 894
Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 895
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. IS-IS normally purges LSPs with an incorrect data link checksum causing the LSP source to regenerate the message. A cycle of purging and regenerating LSPs can occur when a network link continues to deliver accurate LSPs even though there is a link causing data corruption.
PAGE 896
NOTE: IP address is not mandatory for forming IS-IS adjacency. Related Commands ● net — configure an IS-IS network entity title (NET) for the routing process. ● router isis — enable the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process. Syntax ipv6 router isis [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters Defaults tag (OPTIONAL) This parameter is a unique name for a routing process.
PAGE 897
isis circuit-type Configure the adjacency type on interfaces. Syntax isis circuit-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no isis circuit-type command. Parameters Defaults level-1 You can form a Level 1 adjacency if there is at least one common area address between this system and neighbors. You cannot form Level 2 adjacencies on this interface.
PAGE 898
To return to the default values, use the no isis csnp-interval [seconds] [level-1 | level-2] command. Parameters Defaults seconds Interval of transmission time between CSNPs on multi-access networks for the designated intermediate system. The range is from 0 to 65535. The default is 10. level-1 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 1. level-2 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 2.
PAGE 899
Defaults seconds = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 900
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 901
Version Description 8.3.11.1 Introduced on the Z9000. Usage Information Hello PDUs are “padded” only when both the global and interface padding options are ON. Turning either one OFF disables padding for the corresponding interface. Related Commands ● hello padding — turn ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information.
PAGE 902
isis metric Assign a metric to an interface. Syntax isis metric default-metric [level-1 | level-2] To return to the default values, use the no isis metric [default-metric] [level-1 | level-2] command. Parameters default-metric Metric assigned to the link and used to calculate the cost from each other router via the links in the network to other destinations. You can configure this metric for Level 1 or Level 2 routing. The range is from 0 to 16777215 irrespective of the metric style. The default is 10.
PAGE 903
isis network point-to-point Enable the software to treat a broadcast interface as a point-to-point interface. Syntax isis network point-to-point To disable the feature, use the no isis network point-to-point command. Defaults Not enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 904
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 905
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. You can configure priorities independently for Level 1 and Level 2.
PAGE 906
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The IS-IS protocol automatically determines area boundaries and are able to keep Level 1 and Level 2 routing separate. Poorly planned use of this feature may cause configuration errors, such as accidental area partitioning.
PAGE 907
lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs). Syntax lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keywords level-1 to apply the configuration to generation of Level-1 LSPs.
PAGE 908
and there are no triggers for two times the maximum interval, fast behavior is restored (the initial wait time). lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 512 to 16000 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497.
PAGE 909
Parameters Defaults seconds The LSP refresh interval, in seconds. This value must be 300 seconds less than the value specified in the max-lsp-lifetime command. The range is from 1 to 65535 seconds. The default is 900. 900 seconds Command Modes ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 910
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 911
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Change the maximum LSP lifetime with this command. The maximum LSP lifetime must always be greater than the LSP refresh interval. The seconds parameter enables the router to keep LSPs for the specified length of time. If the value is higher, the overhead is reduced on slower-speed links.
PAGE 912
Version Description 6.3.1.0 Introduced. metric-style To generate and accept old-style, new-style, or both styles of type, length, and values (TLV), configure a router. Syntax metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] To return to the default values, use the no metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] command. Parameters Defaults narrow Allows you to generate and accept old-style TLVs.
PAGE 913
Related Commands ● isis metric — configure a metric for an interface. multi-topology Enables multi-topology IS-IS. It also allows enabling/disabling of old and new style TLVs for IP prefix information in the LSPs. Syntax multi-topology [transition] To return to a single topology configuration, use the no multi-topology [transition] command. Parameters Defaults transition Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific.
PAGE 914
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 915
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 916
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 917
level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only. This setting is the default. metric metric- (OPTIONAL) The value used for the redistributed route. Use a metric value that is consistent with the destination protocol. The range is from 0 to 16777215. The default is 0.
PAGE 918
redistribute bgp 1 level-1 metric 32 metric-type external route-map rmap-isis-to-bgp redistribute ospf Redistribute routing information from an OSPF process.
PAGE 919
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command.
PAGE 920
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Configure a network entity title (the net command) to specify the area address and the router system ID. Enable routing on one or more interfaces to establish adjacencies and establish dynamic routing. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 921
overload bit in its LSPs, other routers ignore the unreliable router in their SPF calculations until the router has recovered. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 address. show config Display the changes you made to the IS-IS configuration. Default values are not shown. Syntax show config Command Modes ● ROUTER ISIS (for IPv4) ● CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific.
PAGE 922
multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database. Syntax show isis [vrf vrf-name] database [level-1 | level-2] [local] [detail | summary] [system-id] [lspid] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IS-IS link state database corresponding to that VRF.
PAGE 923
Usage Information The following describes the show isis database command shown in the following example. Field Description IS-IS Level-1/ Level-2 Link State Database Displays the IS-IS link state database for Level 1 or Level 2. LSPID Displays the LSP identifier. The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID. If this byte is not zero, the LSP describes system links.
PAGE 924
Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 10 IPv6 (MT-IPv6) 1511::/64 Metric: 10 IPv6 (MT-IPv6) 2511::/64 Metric: 10 IPv6 (MT-IPv6) 1011::/64 Metric: 10 IPv6 1511::/64 Metric: 10 IP 10.1.1.0 255.255.255.0 Hostname: ISIS IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002D 0xB2CD 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.
PAGE 925
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 926
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. DellEMC# show isis hostname System Id Dynamic Name Static Name *F100.E120.
PAGE 927
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 928
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 929
MAC Address: 0000.0000.0000 Hold Time: 28 Link Local Address: fe80::201:e8ff:fe00:492c Topology: IPv4 IPv6 , Common (IPv4 IPv6 ) Adjacency being used for MTs: IPv4 IPv6 DellEMC# show isis protocol Display IS-IS routing information. Syntax Parameters show isis [vrf vrf-name] protocol vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS routing information corresponding to that VRF.
PAGE 930
Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode. DellEMC# show isis traffic This command allows you to display IS-IS traffic interface information. Syntax show isis [vrf vrf-name] traffic [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS traffic interface information corresponding to that VRF.
PAGE 931
Example Item Description Level-1/Level-2 Hellos (sent/ rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs. Level-1/Level-2 LSPs flooded (sent/rcvd) Displays the number of flooded LSPs sent and received. Level-1/Level-2 LSPs CSNPs (sent/ rcvd) Displays the number of CSNP LSPs sent and received.
PAGE 932
To restore default values, use the no spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keyword level-1 to apply the configuration to Level-1 SPF calculations. level-2 (OPTIONAL) Enter the keyword level-2 to apply the configuration to Level-2 SPF calculations. interval seconds Enter the maximum number of seconds between SPF calculations. The range is from 0 to 120 seconds.
PAGE 933
30 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 934
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 935
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 936
Related Commands ● show lacp — display the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority. Syntax lacp port-priority priority-value To return to the default setting, use the no lacp port-priority priority-value command. Parameters Defaults priority-value Enter the port-priority value. The higher the value number, the lower the priority.
PAGE 937
Parameters Defaults priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 938
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced on the E-Series. ● show lacp — display the LACP information. ● show interfaces port-channel — display information on configured Port Channel groups. show lacp Display the LACP matrix.
PAGE 939
Example (Port-ChannelNumber) Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# show lacp 1 Port-channel 1 admin up, oper up, mode lacp Actor System ID:Priority 32768, Address 0001.e800.a12b Partner System ID:Priority 32768, Address 0001.e801.
PAGE 940
31 Layer 2 This section describes commands to configure Layer 2 features. Topics: • • • MAC Addressing Commands Virtual LAN (VLAN) Commands Far-End Failure Detection (FEFD) MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically.
PAGE 941
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 942
mac-address-table static Associate specific MAC or hardware addresses to an interface and VLANs. Syntax mac-address-table static mac-address {multicast vlan vlan-id output—range interface}{output interface vlan vlan-id} To remove a MAC address, use the no mac-address-table static mac-address output interface vlan vlan-id command. Parameters mac-address Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn format. multicast Enter a vlan port to where L2 multicast MAC traffic is forwarded.
PAGE 943
Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 944
Defaults Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Modified the default option from none to Enabled. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 945
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 946
mac learning-limit learn-limit-violation Configure an action for a MAC address learning-limit violation. Syntax mac learning-limit learn-limit-violation {log | shutdown} To return to the default, use the no mac learning-limit learn-limit-violation {log | shutdown} command. Parameters Defaults log Enter the keyword log to generate a syslog message on a learning-limit violation. shutdown Enter the keyword shutdown to shut down the port on a learning-limit violation.
PAGE 947
To convert the sticky MAC addresses to dynamic MAC addresses, use the no mac learning-limit command. Parameters Defaults mac-addresssticky Configures the dynamic MAC addresses as sticky on an interface. None Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 948
Defaults None Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 949
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 950
interface interface vlan vlan-id (OPTIONAL) Enter the keyword interface then the interface type, slot and port information: ● For a port channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 951
vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display the MAC address assigned to the VLAN. The range is 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.
PAGE 952
dynamic (OPTIONAL) Enter the keyword dynamic to display only those MAC addresses the switch dynamically learns. Optionally, you can also add one of these combinations: address/mac-address, interface/interface, or vlan vlan-id. static (OPTIONAL) Enter the keyword static to display only those MAC addresses specifically configured on the switch. Optionally, you can also add one of these combinations: address/mac-address, interface/interface, or vlan vlan-id.
PAGE 953
Usage Information Example Usage Information Example (Count) Related Commands Version Description pre-6.2.1.1 Introduced on the E-Series. The following describes the show mac-address-table command shown in the following example. Column Heading Description VlanId Displays the VLAN ID number. Mac Address Displays the MAC address in nn:nn:nn:nn:nn:nn format.
PAGE 954
show mac-address-table aging-time Display the aging times assigned to the MAC addresses on the switch. Syntax show mac-address-table aging-time [vlan vlan-id] Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display the MAC address assigned to the VLAN. The range is from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific.
PAGE 955
Parameters mac-address (OPTIONAL) Enter the MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address. interface (OPTIONAL) Enter the keyword interface then the interface type, slot and port information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 956
Parameters violate-action (OPTIONAL) Enter the keywords violate-action to display the MAC learning limit violation status. detail (OPTIONAL) Enter the keyword detail to display the MAC learning limit in detail. interface (OPTIONAL) Enter the keyword interface with the following keywords and the interface information: ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 957
Virtual LAN (VLAN) Commands The following commands configure and monitor virtual LANs (VLANs). VLANs are a virtual interface and use many of the same commands as physical interfaces. You can configure an IP address and Layer 3 protocols on a VLAN called Inter-VLAN routing. FTP, TFTP, ACLs and SNMP are not supported on a VLAN. Occasionally, while sending broadcast traffic over multiple Layer 3 VLANs, the VRRP state of a VLAN interface may continually switch between Master and Backup.
PAGE 958
The Default VLAN contains only untagged interfaces. Related Commands ● interface vlan — configure a VLAN. default-vlan disable Disable the default VLAN so that all switchports are placed in the Null VLAN until they are explicitly configured as a member of another VLAN. Defaults Enabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 959
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 960
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. DellEMC(conf-if-vl-100)# show config ! interface Vlan 100 no ip address no shutdown DellEMC(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch.
PAGE 961
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Updated to support OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Augmented to display PVLAN data for the C-Series and S-Series and revised the output to include the Description field to display a user-entered VLAN description. 7.6.1.
PAGE 962
o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged NUM Status Description Q Ports * 1 Inactive 2 Active U Po1(Te 1/1) T Po20(Te 1/6), Te 1/25 T Te 1/7 3 Active T Po20(Te 1/6) T Te 1/7 U Te 1/1 4 Active U Po2(Te 1/2) T Po20(Te 1/6) T Te 1/7 5 Active T Po20(Te 1/6) T Te 1/7 U Te 1/3 6 Active U Po3(Te 1/4) T Po20(Te 1/6) T Te 1/7 7 Active T Po20(Te 1/6) T Te 1/7 U Te 1/5 P 100 Active T Po1(Te 1/1) T Te 1/2 C 10
PAGE 963
Example (Name) Dellconf)# interface vlan 222 DellEMC(conf-if-vl-222)#name test DellEMC(conf-if-vl-222)#do show vlan name test Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM Status Description 222 Inactive DellEMC(conf-if-vl-222)# Example (OpenFlow instance) * O O O Related Commands NUM 1 3 6 8 12 Status Inactive Inactive Inactive Inactive Inactive Q Ports U Te 1/22 Description Q Ports O Te 1/10 ● vlan-stack
PAGE 964
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 965
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 966
Usage Information Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 967
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 968
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 969
Version Description 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. Related Commands ● fefd reset — clear an interface in Err-disabled state. It doesn’t work until the interface is in errdisabled state. ● fefd mode — change FEFD mode on an interface. fefd interval Set an interval between control packets.
PAGE 970
fefd mode Change the FEFD mode on an interface. Syntax fefd mode {normal | aggressive}] To return the FEFD mode to the default of normal, use the no fefd mode command. Parameters Defaults normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol.
PAGE 971
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 972
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands ● fefd — enable far-end failure detection. ● fefd-global — enable FEFD globally on the system. fefd-global Enable FEFD globally on the system.
PAGE 973
Version Description 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Usage Information Related Commands If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. ● fefd — enable far-end failure detection. ● fefd-global interval — configure an interval between FEFD control packets. ● show fefd — display the FEFD command output.
PAGE 974
Field Description Interface Displays the interfaces type and number. Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets. State Displays the state of the interface and can be one of the following: ● bi-directional (interface is up, connected and hearing neighbor’s echoes).
PAGE 975
32 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 976
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
PAGE 977
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor.
PAGE 978
Defaults systemdescription Enter the keywords system-description to advertise the system description TLVs to the LLDP peer. system-name Enter the keywords system-name to advertise the system name TLVs to the LLDP peer. None Command Modes CONFIGURATION (conf-lldp) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.
PAGE 979
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the Z9000 and S4810. 8.3.19.0 Introduced on the S4820T. clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface.
PAGE 980
clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Syntax clear lldp neighbors [interface interface] Parameters interface interface Defaults (OPTIONAL)Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 981
Parameters interface interface Defaults Enter the following keywords and slot/port[/subport] or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. all Enter the keyword all to display information on all interfaces. events Enter the keyword events to display major events such as timer events.
PAGE 982
Dec 4 22:38:27 : 02 01 2c fe 05 aa bb cc 04 61 fa 01 40 00 00 Dec 4 22:38:28 : 00 00 00 00 00 00 00 00 c6 0f ba 27 Dec 4 22:38:28 : TLV: Chassis ID, Len: 7, Subtype: Mac address Value: 00:a0:c9:00:00:01 Dec 4 22:38:29 : TLV: Port ID, Len: 2, Subtype: Interface name Value: T Dec 4 22:38:29 : TLV: TTL, Len: 2, Value: 300 Dec 4 22:38:29 : TLV: UNKNOWN TLV, ORG_SPEC[aa-bb-cc, 4], Len: Value:a Dec 4 22:38:29 : aa bb cc 04 61 Dec 4 22:38:29 : 40 Dec 4 22:38:29 : TLV: UNKNOWN TLV, Type: 125 Len: 1, Value: @ Dec 4
PAGE 983
hello Configure the rate at which the LLDP control packets are sent to its peer. Syntax hello seconds To revert to the default, use the no hello seconds command. Parameters Defaults seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds. 30 seconds Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 984
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000 and S4810. To enable LLDP on the management interface, use the no disable command in LLDP-MANAGEMENTINTERFACE mode (conf-lldp-mgmtIf). mode To receive or transmit, set LLDP. Syntax mode {tx | rx} To return to the default, use the no mode command.
PAGE 985
multiplier Set the multiple of the hello timer before LLDP declares the interface dead. Syntax multiplier number To return to the default, use the no multiplier command. Parameters Defaults integer Enter the number of consecutive misses before the LLDP declares the interface dead. The range is from 2 to 10. 4 Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 986
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 987
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Before LLDP can be configured on an interface, it must be enabled globally from CONFIGURATION mode. This command places you in LLDP mode on the interface; it does not enable the protocol.
PAGE 988
Usage Information Example Example (Detail) Version Description 9.1.(0.0) Modified output of detail parameter to display remote management IP addresses. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 989
28, 4) 38, 4) 48, 4) 58, 4) 68, 4) 78, 4) 88, 4) 98, 4) (108, (118, 4) ( 19, 4) ( 20, 4) ( 21, 4) ( 22, 4) ( 23, 4) ( 24, 4) ( 25, 4) ( 26, 4) ( 27, 4) ( ( 29, 4) ( 30, 4) ( 31, 4) ( 32, 4) ( 33, 4) ( 34, 4) ( 35, 4) ( 36, 4) ( 37, 4) ( ( 39, 4) ( 40, 4) ( 41, 4) ( 42, 4) ( 43, 4) ( 44, 4) ( 45, 4) ( 46, 4) ( 47, 4) ( ( 49, 4) ( 50, 4) ( 51, 4) ( 52, 4) ( 53, 4) ( 54, 4) ( 55, 4) ( 56, 4) ( 57, 4) ( ( 59, 4) ( 60, 4) ( 61, 4) ( 62, 4) ( 63, 4) (
PAGE 990
The neighbors are given below: ----------------------------------------------------------------------Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet 1/1 Locally assigned remote Neighbor Index: 1 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-
PAGE 991
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 992
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S8420T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 993
As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information. The Organizational Unique Identifier (OUI) for the Telecommunications Industry Association (TIA) is 00-12-BB. ● LLDP-MED Endpoint Device — any device that is on an IEEE 802 LAN network edge, can communicate using IP, and uses the LLDP-MED framework.
PAGE 994
Related Commands Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● protocol lldp (Configuration) — enable LLDP globally. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med guest-voice-signaling To advertise a separate limited voice service for a guest user when the guest voice control packets use a separate network policy than the voice data, configure the system.
PAGE 995
Related Commands ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system. Syntax advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} To return to the default, use the no advertise med location-identification {coordinate-based value | civic-based value | ecs-elin value} command.
PAGE 996
advertise med power-via-mdi To advertise the Extended Power via MDI TLV, configure the system. Syntax advertise med power-via-mdi To return to the default, use the no advertise med power-via-mdi command. Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 997
priority-tagged number Defaults Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 998
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 999
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1000
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● ● debug lldp interface — debug LLDP.
PAGE 1001
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — de bug LLDP. ● show lldp neighbors — display the LLDP neighbors. advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system.
PAGE 1002
Related Commands 1002 Version Description 7.6.1.0 Introduced on the C-Series and E-Series. ● debug lldp interface — debug LLDP. ● show lldp neighbors — display the LLDP neighbors.
PAGE 1003
33 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 1004
command in Global configuration mode. This setting causes the multicast MAC address to be mapped to the cluster IP address for NLB mode of operation of the switch. Related Commands ● clear arp-cache — clear dynamic ARP entries from the ARP table. ● show arp — display the ARP table.
PAGE 1005
Example (Multicast) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for multicast MAC address on the MXL platform.
PAGE 1006
34 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the S4048–ON platform.
PAGE 1007
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 1008
Version Description 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax clear ip msdp statistic peer peer-address Parameters Defaults peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer.
PAGE 1009
debug ip msdp Turn on MSDP debugging. Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters Defaults event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.).
PAGE 1010
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1011
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.0 Introduced If a list is not specified, all SA messages received from the default peer are accepted. You can enter multiple default peer commands.
PAGE 1012
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters Defaults name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1013
Parameters Defaults interface Enter the following keywords and slot/port or number information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number.
PAGE 1014
● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. description name (OPTIONAL) Enter the keyword description then a description name (maximum 80 characters) to designate a description for the MSDP peer.
PAGE 1015
ip msdp redistribute Filter local PIM SA entries in the SA cache. SAs which the ACL denies time out and are not refreshed. Until they time out, they continue to reside in the MSDP SA cache. Syntax Parameters Defaults ip msdp redistribute [list acl-name] list acl-name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1016
Defaults peer-address Enter the peer address of the MSDP peer in a dotted decimal format (A.B.C.D.). access-list name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1017
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the E-Series.
PAGE 1018
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1019
Parameters Defaults peer peer address Enter the keyword peer then the peer address in a dotted decimal format (A.B.C.D.). sa-cache Enter the keywords sa-cache to display the Source-Active cache. summary Enter the keyword summary to display an MSDP peer summary. Not configured. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1020
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults None Command Modes ● EXEC ● EXEC Privilege Command History Example 1020 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1021
35 Multicast Listener Discovery Protocol The Multicast Listener Discovery (MLD) protocol is used by IPv6 routers to discover multicast listeners on a directly attached link. Similar to the Internet Group Management Protocol (IGMP), which handles multicast group memberships in IPv4 networks, MLD is used for multicast management on IPv6 networks.
PAGE 1022
debug ipv6 mld Enable debugging on IPv6 MLD packets. Syntax debug ipv6 mld [vrf vrf-name] {group-address | interface} To turn off debugging, use the no debug ipv6 mld {group-address | interface} command. Parameters Defaults vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format. The :: notation specifies successive hexadecimal fields of zero.
PAGE 1023
ipv6 mld last-member-query-interval Change the MAX Response Time inserted into the Group-Specific Queries sent in response to a Leave Group messages. This interval is also the interval between Group-Specific Query messages. Syntax ipv6 mld last-member-query-interval {milliseconds} To return to the default, use the no ipv6 mld last-member-query-interval {milliseconds} command. Parameters Defaults milliseconds Enter the last member query interval in milliseconds. The range is from 100 to 65535.
PAGE 1024
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld version Configure the MLD version on the system. Syntax ipv6 mld version {1 | 2} Defaults MLD version 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1025
Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 1026
MLD Snooping MLD snooping allows the switch to examine the MLD packets and forwards the decision based on their content. You can configure MLD snooping in subnets that receive MLD queries from either MLD or the MLD snooping querier. MLD snooping limits the IPv6 multicast traffic at Layer 2 by configuring Layer 2 LAN ports and dynamically forwards the IPv6 multicast traffic to the ports that want to receive it.
PAGE 1027
● For a Port Channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1028
ipv6 mld snooping explicit-tracking Enable explicit MLD snooping tracking on an interface. Syntax ipv6 mld snooping explicit-tracking To disable MLD snooping explicit tracking, use the no ipv6 mld snooping explicit-tracking command. Defaults Disabled. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 1029
To disable the querier feature, use the no ipv6 mld snooping querier command. Defaults Disabled Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 1030
show ipv6 mld snooping interface View the configured MLD snooping interfaces. Syntax show ipv6 mld snooping interface [interface] Parameters interface interface Enter the following keywords and slot/port or number information: ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1031
Vlan 2 Gi 1/18 Dell# Multicast Listener Discovery Protocol 1031
PAGE 1032
36 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 1033
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1034
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● protocol spanning-tree mstp — enter MULTIPLE SPANNING TREE mode.
PAGE 1035
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. ● max-age — change the wait time before MSTP refreshes protocol configuration information. ● hello-time — change the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs).
PAGE 1036
● max-age — change the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults max-age Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1037
To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094. bridge-priority Enter the keywords bridge-priority then a value in increments of 4096 as the bridge priority. The range is from zero (0) to 61440.
PAGE 1038
Defaults No default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1039
This command is supported in all STP modes such as STP, RSTP, MSTP, and PVST. The command behavior does not change when a new member port is added to the port-channel or an existing member port is deleted from the configuration. The path cost reflects the cumulative speed of the port-channel member ports.
PAGE 1040
revision The revision number for the multiple spanning tree configuration. Syntax revision range To return to the default values, use the no revision command. Parameters Defaults range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1041
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1042
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Enable the multiple spanning tree protocol prior to using this command.
PAGE 1043
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) loopback BPDU inconsistency causes.
PAGE 1044
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------------------------------------------------------Te 1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge Boundary ---------------------------------------------------------Te 1/1 ErrDis 128.257 128 20000 EDS 0 P2P No No DellEMC# show spanning-tree msti 0 MSTI 0 VLANs mapped 1-4094 Root Identifier has priority 32768, Address 0001.e801.
PAGE 1045
Defaults Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1046
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1047
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced By default, Dell EMC Networking OS implements an optimized flush mechanism for MSTP.
PAGE 1048
37 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1049
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 1050
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 1051
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile.
PAGE 1052
Usage Information After you enable multicast, you can enable IGMP and PIM on an interface. In INTERFACE mode, enter the ip pim sparse-mode command to enable IGMP and PIM on the interface. Related Commands ● ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver.
PAGE 1053
-4 103.103.103.3 --> Source -----------------------------------------------------------------The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic. The mtrace command traverses the reverse path to the source from the destination.
PAGE 1054
-----------0 gi 1/10, 0 gi 1/10, 0 gi 1/11, 224.1.1.1 0.0.0.0 1000 1 gi 1/3, 224.1.1.2 0.0.0.0 1000 1 gi 1/3, 224.1.1.1 165.13.34.5 2000 2 gi 1/5, show ip mroute View the multicast routing table.
PAGE 1055
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 1056
Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 1057
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources.
PAGE 1058
ipv6 multicast-routing Enables IPv6 multicast forwarding. Syntax ipv6 multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable IP multicast forwarding on that VRF. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1059
9.11.3.0 Example Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1060
L2 Ports : L3 Ports : gi 1/10 show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000– ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1061
38 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1062
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1063
● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ● For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. hardware_addres Enter a 48-bit hardware MAC address in nn:nn:nn:nn:nn:nn format. s Defaults None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1064
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero.
PAGE 1065
IPv6 Router Advertisement (RA) Guard The IPv6 RA guard provides support to perform conditional forwarding or blocking of the router advertisement messages that are received at the network device platform. This functionality analyzes and filters the RAs sent by the devices and compares the configuration information on the layer 2 device with the RA frame. Once the layer 2 device validates the content of the RA frame against the configuration, it forwards the RA to its unicast or multicast destination.
PAGE 1066
device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command. Parameters Defaults host Enter the keyword host to set the device-role as host. router Enter the keyword router to set the device-role as router. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 1067
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1068
ipv6 nd ra–guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1069
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands. managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters Defaults on Enter the keyword on to set the managed-config-flag value as ON.
PAGE 1070
Parameters ipv6–access-list name ipv6–prefix-list Defaults Enter the keywords ipv6–access-list then the access-list name. The accesslist name allows a maximum of 140 characters. name Enter the keywords ipv6–prefix-list then the prefix-list name. The prefix-list name allows a maximum of 140 characters. ipv6–macaccess-list name Enter the keywords ipv6–mac-access-list then the mac-access-list name. The mac-access-list name allows a maximum of 140 characters.
PAGE 1071
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ● ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1072
reachable–time Enable the verification of the configured reachability time in the received RA packets. Syntax reachable—time value To reset the advertised reachability time, use the no reachable-timevalue command. Parameters Defaults value Enter the advertised reachability time in milliseconds. The range is from 0 to 3,600,000 milliseconds. None Command Modes POLICY LIST CONFIGURATION Command History Related Commands This guide is platform-specific.
PAGE 1073
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1074
router–preference maximum Enable the verification of the advertised default router preference (DRP) value. The preference value is lower than or equal to the specified limit. If this command is not configured, the verification process is bypassed. Syntax router-preference maximum {high | low | medium} To reset the default router preference value, use the no router-preference maximum {high | low | medium} command. Parameters Defaults high Enter the keyword high to set the DRP value as high.
PAGE 1075
Example Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1076
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Introduced on the S6000–ON, and Z9000 switches.
PAGE 1077
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1078
39 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1079
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface TenGigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1080
If the timer expires and an object’s state has changed, a notification is sent to the client. If no delay is configured, a notification is sent immediately after a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds. Related Commands ● track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface.
PAGE 1081
Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1082
show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object. Syntax show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500.
PAGE 1083
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP. DellEMC# show track Track 1 IP route 23.0.0.
PAGE 1084
To return to the default setting, use the no threshold metric {up number | down number} command. Parameters Defaults up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold. down number Enter a number for the DOWN threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default DOWN threshold is255.
PAGE 1085
track interface ip routing Configure object tracking on the routing status of an IPv4 Layer 3 interface. Syntax track object-id interface interface ip routing To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1086
To return to the default setting, use the no track object-id command. Parameters Defaults object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1087
vrf vrf-name Defaults (Optional) You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1088
not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact IPv4 address and prefix length, the status of the tracked route is considered to be DOWN. When you configure the threshold of an IPv4 route metric as a tracked object, the UP/DOWN state of the tracked route is also determined by the current metric for the route in the routing table.
PAGE 1089
Usage Information Version Description 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv4 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8.
PAGE 1090
● track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. track resolution ip route Configure the protocol-specific resolution value used to scale an IPv4 route metric. Syntax track resolution ip route {isis resolution-value | ospf resolution-value} To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500.
PAGE 1091
IPv6 Object Tracking Commands The following section describes the IPv6 object tracking commands. The following object tracking commands apply to IPv4 and IPv6: ● debug track ● delay ● description ● show running-config track ● threshold metric ● track interface line-protocol show track ipv6 route Display information about all tracked IPv6 routes, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1092
Example Output Description First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP.
PAGE 1093
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a tunnel interface, enter the keyword tunnel.
PAGE 1094
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1095
ipv6-address/ prefix-len Defaults Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128. None Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1096
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1097
40 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1098
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1099
Version Description 9.13(0.0) Introduced on the remaining DNOS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1100
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1101
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1102
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables.
PAGE 1103
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors.
PAGE 1104
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process.
PAGE 1105
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the database-timer rate-limit option for the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1106
Field Description ● MC+ (bit used by MOSPF is set and router is able to forward IP multicast packets) ● MC- (bit used by MOSPF is not set and router cannot forward IP multicast packets) ● E + (router is able to accept AS External LSAs) ● E - (router cannot accept AS External LSAs) ● T + (router can support TOS) ● T - (router cannot support TOS) Example hi: Displays the amount of time configured for the HELLO interval. di: Displays the amount of time configured for the DEAD interval.
PAGE 1107
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series.
PAGE 1108
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. description Add a description about the selected OSPF configuration. S4048–ON Syntax description description To remove the OSPF description, use the no description command.
PAGE 1109
Related Commands Version Description pre- 6.1.1.1 Introduced on the E-Series. ● show ip ospf asbr — display the VLAN configuration. distance Define an administrative distance for particular routes to a specific IP address. S4048–ON Syntax distance weight [ip-address mask access-list-name] To delete the settings, use the no distance weight [ip-address mask access-list-name] command. Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110.
PAGE 1110
distance ospf Configure an OSPF distance metric for different types of routes. S4048–ON Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255. The default is 110.
PAGE 1111
distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table. S4048–ON Syntax distribute-list prefix-list-name in [interface] To delete a filter, use the no distribute-list prefix-list-name in [interface] command. Parameters Defaults prefix-list-name Enter the name of a configured prefix list.
PAGE 1112
distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. S4048–ON Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters Defaults prefix-list-name Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed.
PAGE 1113
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and inter-area routes.
PAGE 1114
Generally, convergence level 1 meets most convergence requirements. Higher convergence levels should only be selected following consultation with Dell EMC Networking technical support. graceful-restart grace-period Specifies the time duration, in seconds, that the router’s neighbors continue to advertise the router as fully adjacent regardless of the synchronization state during a graceful restart.
PAGE 1115
graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart. S4048–ON Syntax graceful-restart helper-reject ip-address To return to default value, use the no graceful-restart helper-reject command. Parameters Defaults ip-address Enter the OSPF router-id, in IP address format, of the restart router that will not act as a helper during graceful restart. Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1116
Parameters Defaults planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only. Support for both planned and unplanned failures. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1117
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF.
PAGE 1118
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface.
PAGE 1119
Usage Information Version Description pre- 6.1.1.1 Introduced on the E-Series. All neighboring routers in the same network must use the same password to exchange OSPF information. ip ospf cost Change the cost associated with the OSPF traffic on an interface. S4048–ON Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters Defaults cost Enter a number as the cost. The range is from 1 to 65535. The default cost is based on the reference bandwidth.
PAGE 1120
ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. S4048–ON Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters Defaults seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds.
PAGE 1121
ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. S4048–ON Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters Defaults seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds. 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1122
To delete a key, use the no ip ospf message-digest-key keyid command. Parameters Defaults keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. No MD5 authentication is configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1123
ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets. S4048–ON Syntax ip ospf mtu-ignore To return to the default, use the no ip ospf mtu-ignore command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1124
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1125
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1126
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Set the time interval to a number large enough to prevent unnecessary retransmissions. ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed.
PAGE 1127
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. S4048–ON Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1128
maximum-paths Enable the software to forward packets over multiple paths. S4048–ON Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths.
PAGE 1129
To disable an OSPF area, use the no network ip-address mask area area-id command. Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format. (/x) area-id Enter the OSPF area ID as either a decimal value or in a valid IP address. Decimal value range is from 0 to 65535. IP address format is dotted decimal format A.B.C.D.
PAGE 1130
passive-interface Suppress both receiving and sending routing updates on an interface. S4048–ON Syntax passive-interface {default | interface} To enable both the receiving and sending routing, use the no passive-interface interface command. To return all OSPF interfaces (current and future) to active, use the no passive-interface default command. Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive.
PAGE 1131
The default keyword sets all interfaces as passive. You can then configure individual interfaces, where adjacencies are desired, using the no passive-interface interface command. The no form of this command is inserted into the configuration for individual interfaces when the no passiveinterface interface command is issued while passive-interface default is configured.
PAGE 1132
route-map map- name tag tag-value Defaults (OPTIONAL) Enter the keywords route-map then the name of the route map. (OPTIONAL) Enter the keyword tag then a number. The range is from 0 to 4294967295. Not configured. Command Modes ROUTER OSPF Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1133
metric-type type-value (OPTIONAL) Enter the keywords metric-type then one of the following: ● 1 = for OSPF External type 1 ● 2 = for OSPF External type 2 route-map map- (OPTIONAL) Enter the keywords route-map then the name of the route map. name tag tag-value Defaults (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. None Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1134
level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
PAGE 1135
Parameters Defaults ip-address Enter the router ID in the IP address format. None. Command Modes ROUTER OSPF Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1136
Parameters Defaults process-id Enter a number for the OSPF instance. The range is from 1 to 65535. vrf name (Optional) Enter the VRF process identifier to tie the OSPF instance to the VRF. All network commands under this OSPF instance are then tied to the VRF instance. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1137
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1138
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.
PAGE 1139
show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. S4048–ON Syntax Parameters Defaults show ip ospf [process-id | vrf vrf-name] asbr process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes ● EXEC ● EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1140
3.3.3.3 1.1.1.1 DellEMC# -/-/-/ E/-/-/ 2 0 10.0.0.2 0.0.0.0 Te 1/1 - 1 0 show ip ospf database Display all LSA information. If you do not enable OSPF on the switch, no output is generated. S4048–ON Syntax show ip ospf process-id [vrf vrf-name] database [database-summary] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1141
Example Field Description Link ID Identifies the router ID. ADV Router Identifies the advertising router’s ID. Age Displays the link state age. Seq# Identifies the link state sequence number. This number allows you to identify old or duplicate link state advertisements. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. DellEMC> show ip ospf 1 database OSPF Router with ID (11.1.2.
PAGE 1142
● the default destination (0.0.0.0) for Type 5 LSAs adv-router ip- address (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1142 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1143
Example Field Description Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. DellEMC# show ip ospf 100 database asbr-summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Asbr (Area 0.0.0.0) LS age: 1437 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.
PAGE 1144
● EXEC Privilege Command History Usage Information 1144 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1145
Example Field Description TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router. External Route Tag Displays the 32-bit field attached to each external route.
PAGE 1146
● the network’s IP address for Type 3 LSAs or Type 5 LSAs ● the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs ● the default destination (0.0.0.0) for Type 5 LSAs adv-router ipaddress (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1146 This guide is platform-specific.
PAGE 1147
Example Field Description Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Length Displays the Fletcher checksum of an LSA’s complete contents. Network Mask Displays the length in bytes of the LSA. Attached Router Identifies the IP address of routers attached to the network. DellEMC# show ip ospf 1 data network OSPF Router with ID (20.20.20.5) (Process ID 1) Network (Area 0.0.0.
PAGE 1148
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 1149
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. OSPFv3 graceful restart supports planned-only and/or unplanned-only restarts. The default is support for both planned and unplanned restarts.
PAGE 1150
Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.4.1.0 Introduced on the E-Series and C-Series. ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface. Syntax ipv6 ospf authentication {null | ipsec spi number {MD5 | SHA1} [keyencryption-type] key}} Parameters null Causes an authentication policy configured for the area to not be inherited on the interface.
PAGE 1151
Usage Information Before you enable IPsec authentication on an OSPFv3 interface, first enable IPv6 unicast routing globally, configure an IPv6 address and enable OSPFv3 on the interface, and assign the interface to an area. An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router. Configure the same authentication policy (same SPI and key) on each OSPFv3 interface in a link.
PAGE 1152
command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode. To disable BFD on a specific interface while you configure BFD in CONFIGURATION mode, use the keyword disable. ipv6 ospf cost Explicitly specify the cost of sending a packet on an interface. Syntax ipv6 ospf interface-cost Parameters Defaults interface-cost Enter a unsigned integer value expressed as the link-state metric.
PAGE 1153
ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down. Syntax ipv6 ospf dead-interval seconds To return to the default time interval, use the no ipv6 ospf dead-interval command. Parameters Defaults seconds Enter the time interval in seconds. The range is from 1 to 65535 seconds. 40 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1154
For AES-CBC, only the AES-128 and AES-192 ciphers are supported. key-encryptiontype key (OPTIONAL) Specifies if the key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). Text string used in authentication. The required lengths of a non-encrypted or encrypted key are: 3DES - 48 or 96 hex digits; DES - 16 or 32 hex digits; AES-CBC -32 or 64 hex digits for AES-128 and 48 or 96 hex digits for AES-192.
PAGE 1155
ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured. Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1156
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.
PAGE 1157
Usage Information Version Description 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. Setting a priority of 0 makes the router ineligible for election as a Designated Router or Backup Designated Router. Use this command for interfaces connected to multi-access networks, not point-to-point networks. ipv6 router ospf Enable OSPF for IPv6 router configuration.
PAGE 1158
maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters Defaults number Specify the number of paths. The range is from 1 to 64. The default is 8 paths. 8 Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1159
● For a port channel interface, enter the keywords port-channel then a number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Enabled, that is sending of routing updates are enabled by default. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1160
static Enter the keyword static to redistribute manually configured routes. metric metric- Enter the keyword metric then the metric value. value The range is from 0 to 16777214. The default is 20. metric-type type-value (OPTIONAL) Enter the keywords metric-type then the OSPFv3 link state type of 1 or 2 for default routes. The values are: ● 1 for a type 1 external route ● 2 for a type 2 external route The default is 2.
PAGE 1161
To return to the previous router ID, use the no router-id ip-address command. Parameters Defaults ip-address Enter the router ID in the dotted decimal format. The router ID is selected automatically from the set of IPv4 addresses configured on a router. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1162
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1163
show crypto ipsec policy Command Fields Field Description Policy name Displays the name of an IPsec policy. Policy refcount Number of interfaces on the router that use the policy. Inbound ESP SPI and Outbound ESP SPI The encapsulating security payload (ESP) security policy index (SPI) for inbound and outbound links. Inbound ESP Auth Key and Outbound Auth Key The ESP authentication key for inbound and outbound links.
PAGE 1164
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1165
replay detection support : N STATUS : ACTIVE show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/ outbound ah Authentication policy applied to inbound or outbound traffic. inbound/ outbound esp Encryption policy applied to inbound or outbound traffic. spi Security policy index number used to identify the policy.
PAGE 1166
Defaults network (OPTIONAL): Enter the keyword network to display the network link states. nssa-external (OPTIONAL): Enter the keyword nssa-external to display the nssa link state information. router (OPTIONAL): Enter the keyword router to display the router link states. None Command Modes EXEC EXEC Privilege Command History Usage Information Example (gracelsa) This guide is platform-specific.
PAGE 1167
Process 1 database summary Type Count/Status Oper Status 1 Admin Status 1 Area Bdr Rtr Status 1 AS Bdr Rtr Status 1 AS Scope LSA Count 0 AS Scope LSA Cksum sum 0 Originate New LSAS 50 Rx New LSAS 22 Ext LSA Count 0 Rte Max Eq Cost Paths 10 GR grace-period 180 GR mode planned and unplanned Area 0 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 6 Rtr LSA Count 2 Net LSA Count 1 Inter Area Pfx LSA Count 1 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra
PAGE 1168
AS External Link States (Area 1) LS Age: 35 LS Type: OSPFv3 NSSA LSA Link State ID: 0.0.0.1 Advertising Router: 1.1.1.1 LS Seq Number: 0x80000001 Checksum: 0xD2DD Length: 52 Prefix: 101:101:1::/64 Prefix Options: 0x8 ( P ) Metric Type: 2 Metric: 20 Forwarding Address: 101:101:1::1 show ipv6 ospf interface View OSPFv3 interface information. Syntax show ipv6 ospf [process-number] [vrf vrf-name] [interface] Parameters process-number Enter the OSPF process number.
PAGE 1169
Usage Information Example Version Description 9.2.(0.0) Added support for showing BFD status on the S4820T, S4810, and Z9000. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. If you enable BFD at the global level, show ipv6 ospf interface shows the BFD provisioning. If you enable BFD at the interface level, show ipv6 ospf interface shows the BFD interval timers.
PAGE 1170
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.
PAGE 1171
router-id 10.10.10.1 snmp context ospf1 ! DellEMC> timers spf Set the time interval between when the switch receives a topology change and starts a shortest path first (SPF) calculation. S4048–ON Syntax timers spf delay holdtime msec To return to the default, use the no timers spf command. Parameters Defaults delay Enter a number as the delay. The range is from 0 to 2147483647. The default is 5 seconds. When configured in milli seconds, 100 is the least value that is allowed to be configured.
PAGE 1172
DellEMC(conf-ipv6-router_ospf)# DellEMC(conf-ipv6-router_ospf)# end DellEMC# 1172 Open Shortest Path First (OSPFv2 and OSPFv3)
PAGE 1173
41 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1174
Related Commands Version Description 8.4.2.0 Introduced on the E-Series. 7.7.1.0 Introduced on the E-Series. ● ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name test [l2–switch] To remove a redirect list from an interface, use the no ip redirect-group name command.
PAGE 1175
NOTE: Apply the redirect list to physical, VLAN, or LAG interfaces only. The Layer2 PBR option matches the layer2 traffic flow. If you un-configure this option, then the Layer2 traffic is not matched. You can apply the l2–switch option to redirect Layer2 traffic only on a VLAN interface. This VLAN interface must be configured with an IP address for ARP resolution. NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces.
PAGE 1176
permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: ● If you know the filter sequence number, use the no seq sequence-number syntax command.
PAGE 1177
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1178
● rst = reset the connection ● syn = synchronize sequence number ● urg = urgent field Defaults source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1179
[bit] [operator]{source-port source-port| source-port-range start-port end-port} {destination-port destination-port| destination-port-range startport - end-port} To delete a filter, use the no seq sequence-number command. Parameters sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the keyword IP address of the forwarding router.
PAGE 1180
destination-port- Enter the keywords destination-port-range then the range of the start port range to end port to be matched in the ACL rule in the ICAP rule. Defaults none Command Modes REDIRECT-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1181
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. The show cam pbr command displays the PBR CAM content.
PAGE 1182
seq 15 redirect tunnel 2 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Next-hop reachable (via Te 1/32) seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.0/24, Track 5 [up], Next-hop reachable (via Po 5) seq 30 redirect 155.1.1.2 track 6 icmp host 8.8.8.8 any, Track 5 [up], Next-hop reachable (via Po 5) seq 35 redirect 42.1.1.2 icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20) seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30) seq 45 redirect 31.1.1.
PAGE 1183
42 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
PAGE 1184
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1185
If you use this command on a peer VLT node, only the synced routes are deleted from the multicast route table. debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command.
PAGE 1186
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled.
PAGE 1187
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters Defaults vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1188
ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History Usage Information This guide is platform-specific.
PAGE 1189
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Removed the in and out parameters. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 1190
Example Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced DellEMC(conf)# ip access-list standard map1 DellEMC(config-std-nacl)# permit 224.0.0.
PAGE 1191
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command.
PAGE 1192
To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. access-list Defaults Enter the name of an extended access list. Maximum 16 characters. Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1193
group-address group-address mask override Enter the keywords group-address then a group-address mask, in dotted decimal format (/xx), to assign that group address to the RP. Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable. NOTE: This option is applicable to multicast group range. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1194
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port-channel interface, enter the keywords port-channel then the port-channel ID. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
PAGE 1195
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1196
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Removed the acl-access-list parameter. Modified the max value of S, G entry second range from 86400 to 65535. Introduced on the S6000ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1197
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.7(0.0) Added support for VRF. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 1198
Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1199
If the PIM DR flood is not disabled (default setting): ● Multicast traffic is transmitted on the egress port towards the PIM DR if the port is not the incoming interface. ● Multicast traffic for an unknown group is sent on the port towards the PIM DR. When DR flooding is disabled, multicast traffic for an unknown group is dropped. show ip pim bsr-router View information on the Bootstrap router.
PAGE 1200
show ip pim interface View information on the interfaces with IP PIM enabled. S4048–ON Syntax show ip pim [vrf vrf-name] interface Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on this VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information 1200 This guide is platform-specific.
PAGE 1201
Field Description DR Displays the IP address of the Designated Router for that interface. The show ip pim interface command does not display information corresponding to the loop-back interfaces. Example DellEMC# show ip pim interface Address Interface Ver/ Mode 165.87.34.5 Te 1/10 v2/S 10.1.1.2 Vl 10 v2/S 20.1.1.5 Vl 20 v2/S 165.87.31.200 Vl 30 v2/S DellEMC# Nbr Count 0 1 1 1 Query Intvl 30 30 30 30 DR Prio 1 1 1 1 DR 165.87.34.5 10.1.1.2 20.1.1.5 165.87.31.
PAGE 1202
Usage Information The following describes the show ip pim neighbor command shown in the following example. Field Description Neighbor address Displays the IP address of the PIM neighbor. Example Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found.
PAGE 1203
Example Example (Mapping) Example (Address) Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. DellEMC# show ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.
PAGE 1204
Usage Information Example (#2) Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series. The following describes the show ip pim snooping interface commands shown in the following example. Field Description Interface Displays the VLAN interfaces with PIM-SM snooping enabled.
PAGE 1205
Field Description Neighbor address Displays the IP address of the neighbor learned through PIM-SM snooping. Example Interface Displays the VLAN ID number and slot/port on which the PIM-SM-enabled neighbor was discovered. Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires).
PAGE 1206
Usage Information Example The following describes the show ip pim snooping tib commands shown in the following example. Field Description (S, G) Displays the entry in the PIM multicast snooping database. uptime Displays the amount of time the entry has been in the PIM multicast route table. expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1207
show ip pim ssm-range Display the non-default groups added using the SSM range feature. 4048–ON Syntax Parameters Defaults show ip pim [vrf vrf-name] ssm-range vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1208
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1209
0/0 0/0 0/0 0/0 State-Refresh messages sent/received MSDP updates sent/received Null Register messages sent/received Register-stop messages sent/received Data path event summary: 0 no-cache messages received 0 last-hop switchover messages received 0/0 pim-assert messages sent/received 0/0 register messages sent/received DellEMC# show ip pim tib View the PIM tree information base (TIB).
PAGE 1210
Example Field Description (S, G) Displays the entry in the multicast PIM database. uptime Displays the amount of time the entry has been in the PIM route table. expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1211
show running-config pim Display the current configuration of PIM-SM. Syntax show running-config pim Command Modes EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.
PAGE 1212
Command History Related Commands Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. show ipv6 pim tib – displays the IPv6 PIM tree information base (TIB) debug ipv6 pim Invoke IPv6 PIM debugging.
PAGE 1213
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 9.14(1.0) Usage Information Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON. This command is applied to the subsequent PIM-BSR. Existing BSR advertisements are cleaned up by time-out.
PAGE 1214
Parameters Defaults priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. 1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.11.3.
PAGE 1215
NOTE: The :: notation specifies successive hexadecimal fields of zero. group-address group-address mask override Enter the keywords group-address then the group address in the x:x:x:x::x format and then the mask in /nn format to assign that group address to the RP. NOTE: The :: notation specifies successive hexadecimal fields of zero. (OPTIONAL) Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable.
PAGE 1216
NOTE: If you do not specify the acl-name, the system uses the default multicast IPv6 group range, which is ff00::/8. Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON.
PAGE 1217
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL.
PAGE 1218
Example Version Description 9.14(1.0) Introduced on the C9010, S3048–ON, S3100 Series, S4048–ON, S4048T–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON.
PAGE 1219
]Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. detail (OPTIONAL) Enter the keyword detail to displayed PIM neighbor detailed information. Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 1220
DellEMC#show run pim ! ip pim bsr-candidate Loopback 0 ip pim vrf red bsr-candidate Loopback 1 ip pim vrf blue bsr-candidate Loopback 2 ip pim vrf red rp-candidate Loopback 1 ip pim vrf blue rp-candidate Loopback 2 ipv6 pim bsr-candidate Loopback 0 ipv6 pim vrf red bsr-candidate Loopback 1 ipv6 pim vrf blue bsr-candidate Loopback 2 ipv6 pim rp-candidate Loopback 0 100 def_vrf_acl ipv6 pim vrf red rp-candidate Loopback 1 100 def_vrf_acl ipv6 pim vrf blue rp-candidate Loopback 2 60 blue_vrf_acl_dut DellEMC# E
PAGE 1221
Example Dell# show ipv6 pim summary PIM TIB version 1480 Uptime 5d4h Entries in PIM-TIB/MFC : 105/81 Active Modes : PIM-SM Interface 3 0 2 summary: active PIM interfaces passive PIM interfaces active PIM neighbors TIB summary: 12/12 (*,G) entries in PIM-TIB/MFC 69/69 (S,G) entries in PIM-TIB/MFC 24/0 (S,G,Rpt) entries in PIM-TIB/MFC 8 PIM nexthops 1 RPs 7 sources 30 Register states Message summary: 47132/53793 Joins/Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/
PAGE 1222
Example Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010.
PAGE 1223
43 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember ● Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). ● The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1224
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1225
monitor multicast-queue Configure monitor QoS multicast queue ID. Syntax monitor multicast-queue queue-id To remove the configuration, use the no monitor multicast-queue command. Parameters Defaults queue-id Enter the QoS multicast queue ID. The range is from 0 to 9. queue-id: 0 Enable status: Disabled Command Modes CONFIGURATION Example Command History DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific.
PAGE 1226
Defaults set ip dscp Configures the Differentiated Services Code Point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default value, use the no form of this command. dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic.
PAGE 1227
rate-limit Configure the rate-limit to limit the mirrored packets. Syntax rate-limit limit To remove the limit, use the no rate-limit limit command. Parameters Defaults limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. 60 Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1228
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1229
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for the RPM / ERPM. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1230
Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1231
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. ● For a port channel interface, enter the keywords port-channel then a number. range Enter the keyword range to specify the list of interfaces. any Enter the keyword any to specify all interfaces.
PAGE 1232
Example 1232 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1233
44 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1234
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. S4048 Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1235
private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. S4048 Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters Defaults community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN.
PAGE 1236
private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters Defaults vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input.
PAGE 1237
To remove PVLAN mode from the selected port, use the no switchport mode private-vlan command. Parameters Defaults host Enter the keyword host to configure the selected port or port channel as an isolated interface in a PVLAN. promiscuous Enter the keyword promiscuous to configure the selected port or port channel as an promiscuous interface. trunk Enter the keyword trunk to configure the selected port or port channel as a trunk port in a PVLAN. Disabled.
PAGE 1238
45 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the S4048 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1239
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. ● protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S4048 Syntax disable To enable PVST+, use the no disable command.
PAGE 1240
Related Commands ● protocol spanning-tree pvst — enter PVST+ mode. extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S4048 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History Example This guide is platform-specific.
PAGE 1241
-------------------------------------------------------Te 1/10 Desg 128.140 128 200000 FWD 0 P2P No Te 1/12 Dis 128.142 128 200000 DIS 0 P2P No DellEMC(conf-pvst)# Related Commands ● protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command.
PAGE 1242
Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands ● disable — disables PVST+. ● show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. S4048 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters Defaults vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094.
PAGE 1243
Usage Information Example (Brief) Version Description 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples.
PAGE 1244
Port 131 (TenGigabitEthernet 1/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.131 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1245
Related Commands ● spanning-tree pvst — configure PVST+ on an interface. spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
PAGE 1246
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
PAGE 1247
no ip address switchport spanning-tree pvst vlan 3 cost 1800 no shutdown DellEMC(conf-if-te-1/1)# end DellEMC# Related Commands ● show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN.
PAGE 1248
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. S4048 Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1249
bridge-priority value Defaults Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. 32768 Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1250
Command Modes CONFIGURATION (conf-pvst) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1251
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1252
Related Commands 1252 Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1253
46 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1254
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis.
PAGE 1255
When you set the priority for a port channel, the physical interfaces assigned to the port channel are configured with the same value. You cannot assign the dot1p-priority command to individual interfaces in a port channel. rate police Police the incoming traffic rate on the selected interface. Syntax Parameters Defaults rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] [vlan vlan-id] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1256
S-Series On one interface, you can configure the rate police command for a VLAN or you can configure the rate police command for an interface. rate-shape Shape the traffic output on the selected interface. Syntax rate shape [kbps] rate [burst-KB] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
PAGE 1257
Related Commands ● rate-shape — shapes traffic output as part of the designated policy. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. S4048–ON Syntax Parameters Defaults service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} queue Enter a value from 0 to 7.
PAGE 1258
To return to the default setting, use the no service-class dynamic dot1p command. Defaults All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command. The default mapping is as follows: dot1p Queue ID 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 Command Modes ● INTERFACE ● CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1259
● All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally. ● Layer 2 or Layer 3 service policies supersede dot1p service classes. strict-priority unicast Configure a unicast queue as a strict-priority (SP) queue. Syntax Parameters Defaults strict-priority unicast number unicast number Enter the keyword unicast then the queue number. The range is from 1 to 3.
PAGE 1260
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify data traffic into one of eight classes . Dell EMC Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
PAGE 1261
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-of-service policies to each class. Syntax Parameters Defaults class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
PAGE 1262
Related Commands ● ● ● ● ● ● ● ● ● ● ip access-list extended — configures an extended IP ACL. ip access-list standard — configures a standard IP ACL. match ip access-group — configures the match criteria based on the access control list (ACL). match ip precedence — identifies the IP precedence values as match criteria. match ip dscp — configures the match criteria based on the DSCP value. match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL.
PAGE 1263
Related Commands Version Description 6.1.1.1 Introduced on the E-Series. ● show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the policies (80 characters maximum).
PAGE 1264
match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IP-any class-maps on both ACLs as well as VLANs.
PAGE 1265
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed. Related Commands ● class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria.
PAGE 1266
Usage Information Version Description 7.7.1.0 Added the keyword multicast ; added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series; added support for the DSCP Marking option. 6.2.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive.
PAGE 1267
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1268
Usage Information Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. To access this command, enter the class-map command.
PAGE 1269
match mac access-group Configure a match criterion for a class map, based on the contents of the designated MAC ACL. Syntax Parameters Defaults [seq sequence number] match mac access-group {mac-acl-name} mac-acl-name Enter a MAC ACL name. Its contents is used as the match criteria in the class map. none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1270
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1271
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced.
PAGE 1272
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information An aggregate output QoS policy applies to all outbound port traffic.
PAGE 1273
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series.
PAGE 1274
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map.
PAGE 1275
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined. This command enables the qos-policy-input configuration mode— (conf-qos-policy-in).
PAGE 1276
Version Description 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rateshape, scheduler strict, bandwidth-percentage, and WRED can be defined. This command enables the qos-policy-output configuration mode—(conf-qos-policy-out).
PAGE 1277
Important Points to Remember — Multicast-Bandwidth Option ● A unique multicast weighted fair queuing (WFQ) setting can be applied only on a per port-pipe basis. The minimum percentage of the multicast bandwidth assigned to any of the ports in the port-pipe takes effect for the entire port-pipe. ● If the percentage of multicast bandwidth is 0, control traffic going through multicast queues are dropped.
PAGE 1278
NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast. rate-police Specify the policing functionality on incoming traffic. Syntax rate-police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] Parameters Defaults kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1279
Related Commands ● rate police — specifies traffic policing on the selected interface. ● qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy. Syntax Parameters Defaults rate-shape [kbps | pps] peak-rate [burst-kbps | burst-packets] commited [kbps | pps] commited-rate [burst-kbps | burst-packets] pps Enter the keyword pps to specify the rate limit in packets per second (pps).
PAGE 1280
propagates at an average rate that is less than or equal to the committed rate, it is considered to be green-colored or coded. When the transmitted traffic falls below the committed rate, the bandwidth, which is not used by any traffic that is traversing the network, is aggregated to form the committed burst size. Traffic is considered to be green-colored up to the point at which the unused bandwidth does not exceed the committed burst size.
PAGE 1281
Usage Information You can attach a single policy-map to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. NOTE: The service-policy commands are not allowed on a port channel. The servicepolicy input policy-map-name command and the service-class dynamic dot1p command are not allowed simultaneously on an interface.
PAGE 1282
Related Commands ● policy-map-output — creates an output policy map. service-queue Assign a class map and QoS policy to different queues. S4048–ON Syntax service-queue queue-id [class-map class-map-name] [qos-policy qos-policyname] To remove the queue assignment, use the no service-queue queue-id [class-map classmap-name] [qos-policy qos-policy-name] command. Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7.
PAGE 1283
Related Commands ● class-map — identifies the class map. ● service-policy input — applies an input policy map to the selected interface. ● service-policy output — applies an output policy map to the selected interface. set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. S4048–ON Syntax Parameters Defaults set {ip-dscp value | mac-dot1p value} ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63.
PAGE 1284
show qos class-map View the current class map information. Syntax show qos class-map [class-name] Parameters Defaults class-name (Optional) Enter the name of a configured class map. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option on all the Dell EMC Networking OS platforms.
PAGE 1285
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1286
Command History Example (IPv4) This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1287
show qos policy-map-input View the input QoS policy map details. S4048–ON Syntax Parameters show qos policy-map-input [policy-map-name] [class class-map-name] [qospolicy-input qos-policy-name] policy-map-name Enter the policy map name. class class-map- name qos-policy-input qos-policy-name Defaults Enter the keyword class then the class map name. Enter the keyword qos-policy-input then the QoS policy name.
PAGE 1288
Example DellEMC# show qos policy-map-input Policy-map-input pmap1 Trust ipv6-diffserv Queue# Class-map-name 0 c0 1 c1 2 c2 3 c3 4 c4 5 c5 6 c6 7 c7 DellEMC# Qos-policy-name q0 q1 q2 q3 q4 q6 q7 show qos policy-map-output View the output QoS policy map details. S4048–ON Syntax show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] Parameters policy-map-name Enter the policy map name. qos-policyoutput qos- Enter the keyword qos-policy-output then the QoS policy name.
PAGE 1289
Example Version Description 6.1.1.1 Introduced on the E-Series. DellEMC# show qos policy-map-output Policy-map-output PolicyMapOutput Aggregate Qos-policy-name AggPolicyOut Queue# Qos-policy-name 0 qosPolicyOutput DellEMC# show qos qos-policy-input View the input QoS policy details. S4048–ON Syntax Parameters Defaults show qos qos-policy-input [qos-policy-name] qos-policy-name Enter the QoS policy name.
PAGE 1290
DellEMC# Rate-police 100 50 peak 100 50 Dscp 32 show qos qos-policy-output View the output QoS policy details. S4048–ON Syntax show qos qos-policy-output [qos-policy-name] Parameters Defaults qos-policy-name Enter the QoS policy name. none Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1291
show qos statistics View QoS statistics. Syntax Parameters show qos statistics {egress—queue [interface]} | {wred-profile [interface]} | [interface] egress-queue interface wred-profile interface interface Defaults Enter the keyword egress-queue to display the egress-queue statistics and optionally one of the following keywords and slot/port or number information. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1292
Version Description 7.7.1.1 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1293
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series.
PAGE 1294
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1295
0 1 Exception 1 0 Allowed (5) 1 1 Exception 13 (2) DellEMC# L2ACL 100 200 L2ACL 1000 200 L2ACL 0 200 … … … L2ACL 1 400 200 Allowed threshold Specify the minimum and maximum threshold values for the configured WRED profiles. S4048–ON Syntax threshold min number max number max-drop-drop To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile.
PAGE 1296
Usage Information To configure the minimum and maximum threshold values for user-defined profiles, use this command. Additionally, to modify the minimum and maximum threshold values for the pre-defined WRED profiles, use this command. If you delete the threshold values of the pre-defined WRED profiles, the profiles revert to their original default values. Table 5.
PAGE 1297
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added fallback to the E-Series. 8.2.1.0 Added dot1p to the C-Series and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added dot1p and IPv6 DSCP . 6.1.1.1 Introduced on the E-Series. When you configure trust, matched bytes/packets counters are not incremented in the show qos statistics command.
PAGE 1298
profile-name Enter your WRED profile name in character format (32 character maximum). Or use one of the five pre-defined WRED profile names. Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_. Defaults When WRED green is applied, default WRED yellow profiles take effect and vice-versa. Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific.
PAGE 1299
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1300
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1301
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1302
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information A color map outlines the codepoint mappings to the appropriate color mapping (green, yellow, red) for the traffic.
PAGE 1303
Version Description Version 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Usage Information If the specified color-map does not exist, the Diffserv Manager (DSM) creates a color map and sets all the DSCP values to green (low drop precedence). Example The following example assigns the color map, bat-enclave-map, to interface te 1/11.
PAGE 1304
Interface TE 1/10 dscp-color-map mapONE Displayed detailed color policy information on an interface. DellEMC# show qos dscp-color-policy detail te 1/10 Interface TenGigabitEthernet 1/10 Dscp-color-map mapONE yellow 4,7 red 20,30 Related Commands ● show qos dscp-color-map — displays DSCP color maps. show qos dscp-color-map Display the DSCP color map for one or all interfaces. Syntax show qos dscp-color-map map-name Parameters Defaults map-name Enter the name of the color map.
PAGE 1305
47 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1306
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1307
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. S4048–ON Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1308
Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic.
PAGE 1309
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command.
PAGE 1310
Related Commands ● redistribute — allows you to redistribute routes learned by other methods. description Enter a description of the RIP routing protocol. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters Defaults description Enter a description to identify the RIP protocol (80 characters maximum). none Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1311
To return to the default values, use the no distance weight [ip-address mask] command. Parameters Defaults weight Enter a number from 1 to 255 for the weight (for prioritization). The default is 120. ip-address (OPTIONAL) Enter the IP address, in dotted decimal format (A.B.C.D), of the host or network to receive the new distance metric. mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x).
PAGE 1312
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific.
PAGE 1313
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Port Channel interface, enter the keywords port-channel then a number. ● For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults connected (OPTIONAL) Enter the keyword connected to filter only directly connected routes.
PAGE 1314
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. S4048–ON Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1315
2 Defaults (OPTIONAL) Enter the number 2 for RIP version 2. RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1316
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1317
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1318
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. S4048–ON Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command.
PAGE 1319
Usage Information Related Commands When a neighbor router is identified, unicast data exchanges occur. Multiple neighbor routers are possible. To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. ● passive-interface — sets the interface to only listen to RIP broadcasts. network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command.
PAGE 1320
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. S4048–ON Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters Defaults prefix-list-name Enter the name of an established Prefix list to determine which incoming routes are modified.
PAGE 1321
Related Commands ● ip prefix-list — enters PREFIX-LIST mode and configure a prefix list. output-delay Set the interpacket delay of successive packets to the same neighbor. S4048–ON Syntax output-delay delay To return to the switch software defaults for interpacket delay, use the no output-delay command. Parameters Defaults delay Specify a number of milliseconds as the delay interval. The range is from 8 to 50. Not configured.
PAGE 1322
passive-interface Suppress routing updates on a specified interface. S4048–ON Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. Parameters Defaults interface Enter the following information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1323
redistribute Redistribute information from other routing instances. Syntax redistribute {connected | static} To disable redistribution, use the no redistribute {connected | static} command. Parameters Defaults connected Enter the keyword connected to specify that information from active routes on interfaces is redistributed. static Enter the keyword static to specify that information from static routes is redistributed. Not configured.
PAGE 1324
Parameters tag (OPTIONAL) Enter the name of the IS-IS routing process. level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric- (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16.
PAGE 1325
metric metric- value route-map map- name Defaults (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16. (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1326
Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1327
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. DellEMC(conf-router_rip)# show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1 DellEMC(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated.
PAGE 1328
Usage Information Example Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24...
PAGE 1329
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1330
flush Defaults ● ● ● ● Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table. The flush value should be greater than the update value. The range is from zero (0) to 4294967295. The default is 240 seconds.
PAGE 1331
Command Modes ROUTER RIP Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1332
48 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1333
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1334
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1335
rmon collection statistics Enable RMON MIB statistics collection on an interface. Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer owner name Defaults Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1336
log (OPTIONAL) Enter the keyword log to generate an RMON event log. This option sets the eventType to either log or log-and-snmptrap in the RMON event table. The default is None. trap community (OPTIONAL) Enter the keyword trap followed by the SNMP community string to generate SNMP traps for an RMON event entry. This option sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table. In addition to the SNMP traps, this option also generates a syslog.
PAGE 1337
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1338
show rmon Display the RMON running status including the memory usage. S4048–ON Syntax show rmon Defaults none Command Modes EXEC Command History Example 1338 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1339
show rmon alarms Display the contents of the RMON alarm table. S4048–ON Syntax Parameters Defaults show rmon alarms [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) Example (Brief) This guide is platform-specific.
PAGE 1340
-------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 6 1.3.6.1.2.1.1.3 7 1.3.6.1.2.1.1.3 8 1.3.6.1.2.1.1.3 9 1.3.6.1.2.1.1.3 10 1.3.6.1.2.1.1.3 11 1.3.6.1.2.1.1.3 12 1.3.6.1.2.1.1.3 13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.3 DellEMC# show rmon events Display the contents of the RMON event table.
PAGE 1341
Example (Index) Example (Brief) Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC(conf)# rmon event 111 -> DellEMC(conf)# rmon event 112 log -> DellEMC(conf)# rmon event 113 trap private -> DellEMC(conf)# rmon event 114 log trap public-> options DellEMC(conf)#do show rmon events RMON event entry 111 description: event type: none.
PAGE 1342
21 21 22 22 DellEMC# show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. S4048–ON Syntax show rmon hc-alarm [index] [brief] Parameters Defaults index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. none Command Modes EXEC Command History Example (Index) 1342 This guide is platform-specific.
PAGE 1343
falling threshold: 300, RMON event index: 4 alarm sampling failed 0 times. alarm owner: alarm storage type: non-volatile. alarm status: OK DellEMC# Example (Brief) DellEMC# show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 DellEMC# show rmon history Display the contents of the RMON Ethernet history table.
PAGE 1344
Example (Index) Example (Brief) Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1345
Usage Information Example (Index) Example (Brief) Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The log table has a maximum of 500 entries.
PAGE 1346
Example (Index) Example (Brief) 1346 Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1347
6003 101236775 6004 101236775 9001 134529054 9002 134529054 9003 134791198 9004 134791198 DellEMC# TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet 2/1 2/1 3/2 3/2 3/1 3/1 Remote Monitoring (RMON) 1347
PAGE 1348
49 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1349
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1350
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. DellEMC# debug spanning-tree rstp bpdu tengigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree.
PAGE 1351
disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1352
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1353
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1354
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● forward-delay — changes the wait time before RSTP transitions to the Forwarding state. ● hello-time — changes the time interval between BPDUs.
PAGE 1355
Example Related Commands DellEMC(conf)# protocol spanning-tree rstp DellEMC(config-rstp)# no disable ● disable — disables RSTP globally on the system. show config View the current configuration for the mode. Only non-default values are displayed. Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1356
guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. Command Modes ● EXEC ● EXEC Privilege Command History Usage Information Example (Brief) 1356 This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1357
Te 4/1 128.419 128 20000 FWD 20000 16384 0001.e801.6aa8 128.419 Te 4/8 128.426 128 20000 FWD 20000 8192 0001.e805.e306 128.130 Te 4/9 128.427 128 20000 BLK 20000 8192 0001.e805.e306 128.131 Interface Name Role ----------Te 4/2 Desg Te 4/1 Desg Te 4/8 Root Te 4/9 Altr DellEMC# Example (EDS, LBK) PortID Prio Cost Sts Cost Link-type Edge ---- ------- --- ------- --------- ---128.418 128 20000 FWD 20000 P2P Yes 128.419 128 20000 FWD 20000 P2P Yes 128.426 128 20000 FWD 20000 P2P No 128.
PAGE 1358
Parameters cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1359
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the optional bridge port data unit (BPDU) guard. 6.2.1.1 Introduced on the E-Series. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1360
Usage Information 1360 Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.
PAGE 1361
50 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
PAGE 1362
51 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant.
PAGE 1363
Defaults exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. dot1x Enter the keyword dot1x to send accounting information when a dot1x user has logged in. commands { level | role role-name } Enter the keyword commands then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role.
PAGE 1364
Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
PAGE 1365
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. ● aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL.
PAGE 1366
aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters Defaults group-name Enter the name of the RADIUS server group. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific.
PAGE 1367
Usage Information Example Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.
PAGE 1368
Defaults commands { level | role role-name } Enter the keyword commands followed by either a privilege level for accounting of commands executed at that privilege level, or enter the keyword role then the role name for authorization of commands executed by a user with that user role. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands. none Command Modes LINE Command History Related Commands This guide is platform-specific.
PAGE 1369
Defaults default Define the default list of authorization methods. local Use the authorization parameters on the system to perform authorization. tacacs+ Use the TACACS+ protocol to perform authorization. none Enter the keyword none to apply no authorization. none Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1370
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1371
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS.
PAGE 1372
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1373
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys.
PAGE 1374
If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command. Related Commands ● show running-config— Display the current configuration and display changes from the default values. ● service password-encryption— Encrypts all passwords configured in the system. Authentication and Password Commands To manage access to the system, use the following the commands.
PAGE 1375
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell EMC Networking OS uses the methods defined for Enable access instead.
PAGE 1376
... method4 Defaults (OPTIONAL) Enter up to four additional methods. In the event of a “no response” from the first method, the system applies the next configured method (up to four configured methods). Not configured (that is, no authentication is performed). Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1377
Related Commands ● ● ● ● login authentication — enables AAA login authentication on the terminal lines. password — creates a password. radius-server host — specifies a RADIUS server host. tacacs-server host — specifies a TACACS+ server host. aaa reauthenticate enable Enable re-authentication of user whenever there is a change in the authenticators. Syntax aaa reauthenticate enable To disable the re-authentication option, use the no aaa reauthenticate enable command.
PAGE 1378
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1379
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1380
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1381
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1382
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1383
password Defaults Enter a text string up to 96 characters long. The first character of the password must be a letter. You cannot use spaces in the password. No password is configured. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.
PAGE 1384
Parameters min-length number max-retry number lockout-period minutes (OPTIONAL) Enter the keywords min-length then the number of characters. The range is from 0 to 32 characters. (OPTIONAL) Enter the keywords max-retry then the number of maximum password retries. The range is from 0 to 16. (OPTIONAL) Enter the keyword lockout-period then the number of minutes. The range is from 1 to 1440 minutes. The default is 0 minutes and the lockoutperiod is not enabled.
PAGE 1385
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. In the following example, after 5 un-successful login attempts, the session (SSH/TELNET) goes into a locked state for 5 minutes. If all the 10 sessions are locked out with 5 un-successful attempts in each session, no users can login during the lockout-period.
PAGE 1386
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1387
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show privilege Current privilege level is 15. DellEMC# DellEMC# show privilege Current privilege level is 14. DellEMC# DellEMC# show privilege Current privilege level is 10.
PAGE 1388
Usage Information Example Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using.
PAGE 1389
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1390
● 7 to indicate that a password encrypted using a DES hashing algorithm follows. This encryption type is available with the password option only. ● 5 to indicate that a password encrypted using an MD5 hashing algorithm follows. This encryption type is available with the secret option only, and is the default encryption type for this option. password Enter a string up to 32 characters long. dynamic-salt Enter the keyword dynamic-salt to have an additional random input in the password encryption process.
PAGE 1391
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To view the defined user names, use the show running-config user command. You can use the dynamic-salt option only under the secret and the password options. When you configure the password, the system alerts if your password does not match the following criteria. The system accepts your password even if these conditions are not met.
PAGE 1392
client Configures trusted DAC clients. Syntax client {ipv4-addr | ipv6-addr | hostname} [vrf vrf-name] [key [encryptiontype] key] To undo the DAC client configuration, enter the no client host command. Defaults Parameters If VRF is not configured, default VRF is considered. ipv4–addr Enter the keyword ipv4–addr to specify the IPv4 address of the DAC. ipv6–addr Enter the keyword ipv6–addr to specify the IPv6 address of the DAC. hostname Enter the keyword hostname to enter the name of the host.
PAGE 1393
Usage Information ● Configure global shared key applicable for DA clients. If client configuration has shared key configured, that will take precedence. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1394
Version Description 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010–ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. coa-reauthenticate Configure NAS to re-authenticate dot1x user session requests from DAC. Syntax coa-reauthenticate To allow or reject re-authentication requests, enter the no coa-reauthenticate command. Defaults Enabled. Command Modes ● CONF-DYNAMIC-AUTH Command History This guide is platform-specific.
PAGE 1395
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. da-rsp-timeout Configure timeout value for the back end task to respond to DAC requests. Syntax da-rsp-timeout minutes To undo the configuration, enter the no da-rsp-timeout command. Defaults Parameters 10 Minutes. minutes Enter the time out value.
PAGE 1396
dynamic-auth-enable Configure NAS to receive and process dynamic authorization messages. Syntax dynamic-auth-enable To stop NAS from receiving and processing dynamic authorization messages, use the no dynamicauth-enable command. Defaults Disabled. Command Modes ● CONF-DYNAMIC-AUTH Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1397
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series.
PAGE 1398
Usage Information ● All dynamic authorization commands are configured by entering this mode. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1399
radius-server group Creates or deletes a group of radius servers. Syntax Parameters Defaults radius-server group group-name group-name Enter the group name that denotes the group of RADIUS servers. Not configured. Command Modes CONFIGURATION Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1400
auth-port port- number acct-port port- number retransmit retries (OPTIONAL) Enter the keywords auth-port then a number as the port number. The range is from zero (0) to 65535. The default port-number is 1812. (OPTIONAL) Enter the keywords acct-port then a number as the port number. The range is from 1 to 65535. The default port-number is 1813. (OPTIONAL) Enter the keyword retransmit then a number as the number of attempts. This parameter overwrites the radius-server retransmit command.
PAGE 1401
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. To configure any number of RADIUS server hosts for each server host that is configured, use this command. Dell EMC Networking OS searches for the RADIUS hosts in the order they are configured in the software. The global default values for the timeout, retransmit, and key optional parameters are applied, unless those values are specified in the radius-server host or other commands.
PAGE 1402
● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number. ● For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes RADIUS SERVER GROUP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1403
● 0 is the default and means the key is not encrypted and stored as clear text. ● 7 means that the key is encrypted and hidden. key Defaults Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 96 characters long. Not configured. Command Modes CONFIGURATION Command History Usage Information Related Commands This guide is platform-specific.
PAGE 1404
Parameters Defaults retries Enter a number of attempts that the Dell OS tries to locate a RADIUS server. The range is from zero (0) to 100. The default is 3 retries. 3 retries Command Modes CONFIGURATION Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 1405
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1406
replay-protection-window Configure replay protection window period to drop the duplicate packets. Syntax replay-protection-window minutes To undo the configuration, enter the no replay-protection-window command. Defaults Parameters 5 Minutes. minutes Enter the number of minutes to drop the packets. The range is from 1 to 10 minutes.
PAGE 1407
TACACS+ Commands Dell EMC Networking OS supports TACACS+ as an alternate method for login authentication. tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command . Parameters Defaults group-name Enter the name of the TACACS server group. Not configured.
PAGE 1408
Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1409
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1410
Usage Information Example Related Commands You can associate a TACACS server group with a VRF. DellEMC(conf)# tacacs-server group group1 DellEMC(conf-tacacs-group)# tacacs-server host 1.1.1.1 key secret DellEMC(conf-tacacs-group)# tacacs-server host 2.2.2.
PAGE 1411
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 1412
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1413
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1414
● If an 802.1X port is authenticated and put in the RADIUS server assigned VLAN, any change to the port access VLAN configuration does not take effect. ● The 802.1X with VLAN assignment feature is not supported on trunk ports, dynamic ports, or with dynamic-access port assignment through a VLAN membership. dot1x authentication (Configuration) Enable dot1x globally; dot1x must be enabled both globally and at the interface level.
PAGE 1415
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1416
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed attempts, the interface is moved to the authentication failed VLAN.
PAGE 1417
dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters Defaults vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port[/subport]) Command History Usage Information This guide is platform-specific.
PAGE 1418
dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell EMC Networking OS attempts to authenticate the host based on its MAC address. Syntax [no] dot1x mac-auth-bypass Defaults Disabled Command Modes INTERFACE Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1419
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1420
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator performs authentication only when port-control is set to auto. dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command.
PAGE 1421
Parameters Defaults interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated. The range is from 1 to 31536000 (1 year). The default is3600 (1 hour). 3600 seconds (1 hour) Command Modes INTERFACE Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1422
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1423
Version Description 7.4.1.0 Introduced on the E-Series. dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Syntax dot1x supplicant-timeout seconds To return to the default, use theno dot1x supplicant-timeout command. Parameters Defaults seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30.
PAGE 1424
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1425
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. DellEMC#show dot1x interface fortyGigE 1/48 802.
PAGE 1426
Auth PAE State: Backend State: DellEMC# Initialize Initialize SSH and SCP Commands Dell EMC Networking OS supports secure shell (SSH) protocol version 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted and use authentication. crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1427
Usage Information The host keys are required for key-exchange by the SSH server. If the keys are not found when you enable the server (ip ssh server enable), the keys are automatically generated. This command requires user interaction and generates a prompt prior to overwriting any existing host keys. NOTE: Only a user with superuser permissions should generate host-keys. Example Related Commands DellEMC(conf)# crypto key generate rsa Enter key size <1024-2048>. Default<1024> : Host key already exists.
PAGE 1428
Command Modes EXEC Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1429
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command.
PAGE 1430
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh challenge–response–authentication Enable challenge response authentication for SSHv2.
PAGE 1431
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1432
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. If you enable this command, clients can log in without a password prompt. This command provides two levels of authentication: ● rhost-authentication is done with the file specified in the ip ssh rhostfile command. ● checking client host-keys is done with the file specified in the ip ssh pub-key-file command. NOTE: Administrators must specify the two files (rhosts and pub-key-file) to configure hostbased authentication.
PAGE 1433
To disable password-authentication, use the no ip ssh password-authentication enable command. Parameters Defaults enable Enter the keyword enable to enable password-authentication for the SSH server. Enabled Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1434
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1435
Command Modes CONFIGURATION mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1436
Example Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. DellEMC#conf DellEMC(conf)# ip ssh rhostsfile flash://shosts DellEMC(conf)# This command specifies the rhost file used for host-based authentication. This creates/ file overwrites the flash:/ADMIN_DIR/ssh/shosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command once.
PAGE 1437
Usage Information Enabling RSA authentication allows the user to log in without being prompted for a password. In addition, the OpenSSH compatible SSHv2 RSA public key must be added to the list of authorized keys (ip ssh rsa-authentication my-authorized-keys device://filename command). ip ssh server Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative.
PAGE 1438
● hmac-sha1 ● hmac-sha1-96 ● hmac-sha2-256 kex key-exchangealgorithm Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server. The following key exchange algorithms are available: ● diffie-hellman-group-exchange-sha1 ● diffie-hellman-group1-sha1 ● diffie-hellman-group14-sha1 When FIPS is enabled, the default key-exchange-algorithm is diffie-hellmangroup14-sha1.
PAGE 1439
Usage Information Version Description 9.5(0.1) Introduced the cipher , kex and mac options on the Z9500. 9.5(0.0) Introduced the cipher, kex and mac options on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1440
To disable the SSH server configuration, use the no ip ssh server vrf {management | vrfname} command. Parameters Defaults any Enter the keyword any to enable access to the server from any VRF. vrf management Enter the keyword vrf followed by the keyword management to configure an SSH server on a management VRF. vrf vrf-name Enter the keyword vrf followed by the VRF name to configure an SSH server on that VRF.
PAGE 1441
● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. ● For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. ● For a port channel interface, enter the keywords port-channel then a number. ● For a Null interface, enter the keyword null then the Null interface number.
PAGE 1442
Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1443
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command is useful if the remote SSH client implements Strict Host Key Checking.
PAGE 1444
Example Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default.
PAGE 1445
Usage Information Example Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash://ADMIN_DIRssh/knownhosts file. DellEMC# show ip ssh client-pub-keys 4.8.1.
PAGE 1446
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command displays the contents of the flash:/ADMIN_DIR/ssh/authorizedkeys.username file.
PAGE 1447
-c encryption cipher Enable the “FIPS mode enable", this mode will support the v2 client. "no fips mode enable"(disable) will support v1 & v2 client. This comment is applicable for both ciphers & HMAC algorithms: ● 3des-cbc: Force ssh to use 3des-cbc encryption cipher.
PAGE 1448
Version Description ● ● ● ● ● Usage Information Example aes128-ctr aes192-ctr aes256-ctr hmac-sha2-256 hmac-sha2-256-96 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Added support for the -c and -m parameters on the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Added IPv6 support. Introduced on the C-Series. pre-6.1.1.
PAGE 1449
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 1450
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1451
Defaults vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected. ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1452
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1453
ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1454
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping vlan Enable DHCP Snooping on one or more VLANs. Syntax [no] ip dhcp snooping vlan name Parameters Defaults name Enter the name of a VLAN on which to enable DHCP Snooping. Disabled.
PAGE 1455
show ip dhcp snooping Display the contents of the DHCP binding table. Syntax show ip dhcp snooping binding Defaults none Command Modes ● EXEC ● EXEC Privilege Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1456
aaa authorization role-only Configure authentication to use the user’s role only when determining if access to commands is permitted. Syntax aaa authorization role-only To return to the default setting, use the no aaa authentication role-only command. Parameters Defaults name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1457
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1458
router for Router mode Defaults addrole Enter the keyword addrole to add permission to the command. You cannot add or delete rights for the sysadmin role. deleterole Enter the keyword deleterole to remove access to the command. You cannot add or delete rights for the sysadmin role. role-name Enter a text string for the name of the user role up to 63 characters. These are 3 system defined roles you can modify: secadmin, netadmin, and netoperator.
PAGE 1459
Command Modes EXEC Privilege Command History Examples This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1460
Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL.
PAGE 1461
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role from scratch.
PAGE 1462
Table 7. Suppressed ICMPv4 message types (continued) ICMPv4 Message Types Router advertisement (9) Router solicitation (10) Time exceeded (11) IP header bad (12) Timestamp request (13) Timestamp reply (14) Information request (15) Information reply (16) Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMPv4 message type Echo request (8). Table 8.
PAGE 1463
drop icmp Drops the ICMPv4 and ICMPv6 packets. Syntax drop {icmp | icmp6} Command Modes CONFIGURATION Command History Usage Information This guide is platform-specific. For command information about other Platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on the S4810, S4820T, S3048–ON, S3100 Series, S4048–ON, S5000, S6000, S6000–ON, Z9500, Z9100–ON, S6100–ON, S6010–ON, S4048T–ON, C9000, and MXL.
PAGE 1464
● ● ● ● A A A A minimum minimum minimum minimum of of of of one one one one lower case letter (a to z) upper case letter (A to Z) numeric character (0 to 9) special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") If your password does not meet the criteria, the system does not accept your password. When you upgrade the Dell EMC Networking OS image, ensure that you upgrade the boot loader. CAUTION: After configuring the boot access password, save it to a secure location.
PAGE 1465
root-access password Configure the root access password. Syntax root-access password [encryption-type] root-password To reset to the default password, use the no root-access password command. Parameters encryption-type (OPTIONAL) Enter an encryption type for the root password that you enter. ● 0 directs the system to store the password as clear text. ● 7 directs the system to store the password with a dynamic salt.
PAGE 1466
Command History Usage Information Example Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, MXL, and FN-IOM. When you reboot the system using the reload command, the system performs OS image verification on the primary boot image.
PAGE 1467
Command Modes CONFIGURATION Command History Example Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM.
PAGE 1468
52 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1469
Defaults in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID. The range is from 1 to 4094. count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Debug disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1470
Example Related Command Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1471
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command ● show protocol-tunnel — displays tunneling information for all VLANs.
PAGE 1472
protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters Defaults rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History Example Related Commands 1472 This guide is platform-specific.
PAGE 1473
show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax Parameters Defaults show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094. none Command Modes EXEC Command History Example Example (Specific VLAN) Related Commands This guide is platform-specific.
PAGE 1474
53 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. ● The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. ● The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1475
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6address} agent-addr {ipv4-address | ipv6-address} [number [max-datagramsize number]] | [max-datagram-size number] [vrf management] command.
PAGE 1476
Usage Information Version Description 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both.
PAGE 1477
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
PAGE 1478
sflow extended-switch enable Enable packing information on a switch only. Syntax sflow extended-switch enable To disable packing information, use the no sflow extended-switch [enable] command. Parameters Defaults enable Enter the keyword enable to enable global extended information. Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1479
Parameters Defaults extended Enter the keyword extended to copy 256 bytes from the sample packets to sFlow datagram. 128 bytes Command Modes CONFIGURATION INTERFACE Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1480
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1481
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This command sets the counter polling interval for an interface. Related Commands ● sflow polling-interval (Global) — globally sets the polling interval. sflow sample-rate (Global) Change the global default sampling rate.
PAGE 1482
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This command changes the global default sampling rate. You can configure an interface to use a different sampling rate than the global sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power of 2 value.
PAGE 1483
Usage Information This command changes the sampling rate for an interface. By default, the sampling rate of an interface is set to the same value as the current global default sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power-of-2 value. Select one of these two number and re-enter the command. Related Commands ● sflow sample-rate (Global) — changes the sampling rate globally.
PAGE 1484
Usage Information Example The dropEvent counter (sFlow samples dropped due to sub-sampling) shown in the following example always displays a value of zero. DellEMC#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header size: 128 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.1, Agent IP addr: 1.1.1.
PAGE 1485
54 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1486
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1487
Example Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.
PAGE 1488
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example Related Commands The following Example displays a group named ngroup.
PAGE 1489
RFC1213-MIB EtherLike-MIB SNMP-FRAMEWORK-MIB RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.35 1.3.6.1.6.3.10 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1490
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1491
snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1492
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
PAGE 1493
The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB. If a community string is configured without a security-name (for example, snmp-server community public ro), the community is mapped to a default security-name/group: ● v1v2creadu / v1v2creadg — maps to a community with ro (read-only) permissions. ● v1v2cwriteu/ v1v2cwriteg — maps to a community with rw (read-write) permissions. The community-name parameter indexes this command.
PAGE 1494
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps.
PAGE 1495
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the following two SNMP notification options: syslog-reachable and syslog-unreachable. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.
PAGE 1496
NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device. If no VRF is specified, then the default VRF is used. udp-port port- number engineID Defaults Enter the keywords udp-port followed by the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. As above. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1497
snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
PAGE 1498
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.2 Added support for the access parameter. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1499
NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps. informs (OPTIONAL) Enter the keyword informs to send inform notifications to the specified host. The default is traps.
PAGE 1500
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced MAC address notification traps on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148 and S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1501
To 1. 2. 3. 4. 5. Related Commands send an inform, use the following steps: Configure a remote engine ID. Configure a remote user. Configure a group for this user with access rights. Enable traps. Configure a host to receive informs. ● snmp-server enable traps — enables SNMP traps. ● snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server.
PAGE 1502
Parameters Defaults byte-count Enter one of the following values 8, 16, 24 or 32. Packet sizes are 8000 bytes, 16000 bytes, 32000 bytes, and 64000 bytes. 8 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1503
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1504
remote ip- address Enter the keywords udp-port then the user datagram protocol (UDP) port number on the remote device. The range is from 0 to 65535. The default is 162. vrf vrf-name Enter the keywords vrf and then the name of the VRF this is used to connect to the SNMP server. NOTE: Use this attribute to specify a VRF name that is used to connect to the remote host. If no VRF is specified, then the default VRF is used.
PAGE 1505
Usage Information Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.(0.0) Added aes 128 encryption algorithm parameter. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1506
snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826. RFCs for SNMPv3 define two authentication hash algorithms, namely, HMAC-MD5-96 and HMAC-SHA1-96. These are the full forms or editions of the truncated versions, namely, HMAC-MD5 and HMAC-SHA1 authentication algorithms.
PAGE 1507
not previously set up. Otherwise, you must remove the previously configured users before you change the FIPS mode. Example Related Commands DellEMC# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv aes128 d0452401a8c3ce42804fe80e3ba8763d ● show snmp user — Displays the information configured on each SNMP user name. snmp-server view Configure an SNMPv3 view.
PAGE 1508
Usage Information Example Related Commands The oid-tree variable is a full sub-tree starting from 1.3.6 and cannot specify the name of a sub-tree or a MIB. The following Example configures a view named rview that allows access to all objects under 1.3.6.1. DellEMC# conf DellEMC#(conf) snmp-server view rview 1.3.6.1 included ● show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF.
PAGE 1509
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1510
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1511
default logging buffered Return to the default setting for messages logged to the internal buffer. Syntax default logging buffered Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1512
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands ● logging console — set the logging console parameters.
PAGE 1513
Related Commands ● logging monitor — set the logging monitor parameters. ● terminal monitor — send system messages to the terminal/monitor. default logging trap Return to the default settings for logging messages to the Syslog servers. Syntax default logging trap Defaults level = 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1514
Defaults hostname Enter the name of a host already configured and recognized by the switch. udp Enter the keyword udp to enable transmission of log message over UDP followed by port number. The default port is 514 tcp Enter the keyword tcp to enable transmission of log message over TCP followed by port number. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to enable the logging process in VRF mode.
PAGE 1515
logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. Syntax logging buffered [level] [size] To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffered command.
PAGE 1516
logging console Specify which messages are logged to the console. Syntax logging console [level] To return to the default values, use the default logging console command. To disable logging to the console, use the no logging console command. Parameters Defaults level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1517
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1518
● ● ● ● ● ● ● ● ● ● ● ● ● local7 (local use) lpr (line printer system) mail (mail system) news (USENET news) sys9 (system use) sys10 (system use) sys11 (system use) sys12 (system use) sys13 (system use) sys14 (system use) syslog (Syslog process) user (user process) uucp (Unix to Unix copy process) The default is local7. Defaults local7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1519
To return to the default values, use the no logging history command. Parameters Defaults level Indicate a value from 0 to 7 or enter one of the following equivalent words: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 4 or warnings. warnings or 4 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1520
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1521
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1522
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you use the no logging on command, messages are logged only to the console. Related Commands ● ● ● ● logging logging logging logging — enable logging to the Syslog server. buffered — set the logging buffered parameters. console — set the logging console parameters. monitor — set the logging parameters for the terminal connections.
PAGE 1523
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1524
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1525
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5.
PAGE 1526
Example DellEMC(conf)#logging version ? <0-1> Select syslog version (default = 0) DellEMC(conf)#logging version 1 show logging Display the logging settings and system messages logged to the internal buffer of the switch. Syntax show logging [number | history [reverse][number] | reverse [number] | summary] Parameters number (OPTIONAL) Enter the number of messages displayed in the output. The range is from 1 to 65535.
PAGE 1527
Console logging: level debugging Monitor logging: level debugging Buffer logging: level debugging, 5604 Messages Logged, Size (524288 bytes) Trap logging: level informational Oct 8 09:25:37: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 223.80.255.254 closed. Hold time expired Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.13.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.1.1.13 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 1.1.14.
PAGE 1528
Example Related Commands Version Description 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. DellEMC(conf)# show logging auditlog ● clear logging auditlog — clear the audit log. show logging driverlog stack-unit Display the driver log for the specified hardware component.
PAGE 1529
3:Task(tUsrRoot): [ 61]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main block failed errcode 6 4:Task(tUsrRoot): [ 89]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed checksum calulated checksum 0xc9a6 actual chksum 0x0 5:Task(tUsrRoot): [ 57]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed errcode 6 6:Task(tUsrRoot): [ 51]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom, failed to get any good block 7:Task(tUsrRoot): [ 75]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main b
PAGE 1530
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands 1530 ● logging monitor — set the logging parameters on the monitor/terminal.
PAGE 1531
55 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1532
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 19 TR_CHM_RPM_U P 1.3.6.1.4.1.6027.3.2 6.1.5.1.5 dellNetSysAlarmRp mUp DELLNETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the primary RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_D OWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.6 dellNetSysAlarmRp mDown DELLNETWORKINGCHASSIS-MIB.
PAGE 1533
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the minor threshold. 28 TR_CHM_FANTRA 1.3.6.1.4.1.6027.3.2 Y_BAD_CLR 6.1.5.1.14 dellNetSysAlarmFa nTrayClear DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray is now operational. 29 TR_CHM_MIN_FA NBAD_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.15 dellNetSysAlarmMi norFanBadClear DELLNETWORKINGCHASSIS-MIB.
PAGE 1534
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME 42 Object Name MIB File Explanation TR_STP_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib 802.1d new root trap support. 43 TR_STP_TOPOLO GY_CHANGE topologyChange BRIDGE-MIB.mib 802.1d topology change trap support. 44 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_BRIDGE 2.0.1 Not Available Not Available MSTP Not Supporting 45 TR_MSTP_NEW_R 1.3.6.1.4.1.6027.20. OOT_PORT 2.0.
PAGE 1535
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation type. Implementation of this trap is optional 55 TR_VRRPV3_LEAV 1.3.6.1.4.1.6027.3.2 E_MASTER 6.1.5.1.44 dellNetSysAlarmVrr DELLpGoMaster NETWORKINGCHASSIS-MIB.mib The VRRP generate this trap when it become a backup 56 TR_VRRPV3_GIVE UP_MASTER dellNetSysAlarmVrr DELLpGiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1536
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued.
PAGE 1537
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation index into the MEP table (dot1agCfmMepTa ble). 62 TR_EOAM_THRSH 1.3.6.1.2.1.158.0.1 LD_EVT dot3OamThreshold Event stdeoam.mib "A dot3OamThreshold Event notification is sent when a local or remote threshold crossing event is detected.
PAGE 1538
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the dot3OamEventLog Table.
PAGE 1539
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 68 TR_FIPS_ENODE_ DROP 1.3.6.1.4.1.6027.3.2 2.4.0.5 dellNetENodeDrop pedTrap DELLNETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION 1.3.6.1.4.1.6027.3.2 _DROP 2.4.0.6 dellNetSessionReq uestDroppedTrap DELLNETWORKINGFIPSNOOPINGMIB.
PAGE 1540
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation dellNetETSGlobalE nableTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST 1.3.6.1.4.1.6027.3.15 dellNetETSPortDcb DELLATE_CHANGE .4.0.4 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1541
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation enabled to send the trap for Peer Up or Peer Down 78 TR_PFC_OPER_S TATE_CHANGE 1.3.6.1.4.1.6027.3.15 dellNetPFCPortDcb DELL.4.0.8 xOperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dellNetPFCGlobalE nableTrap is enabled to send the trap for PFC state machine state change 79 TR_MPLS_TUNNE L_UP 1.3.6.
PAGE 1542
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 92 TR_CHM_MIN_AL ARM_PS_CLR 1.3.6.1.4.1.6027.3.2 6.1.5.1.19 dellNetSysAlarmMi norPSClr DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when a power supply minor alarm is cleared. 93 TR_CHM_MIN_FA NBAD 1.3.6.1.4.1.6027.3.2 6.1.5.1.20 dellNetSysAlarmMi norFanBad DELLNETWORKINGCHASSIS-MIB.mib The agent generate this trap when fan is bad. 94 TR_SYSADM_CPU _THRESHOLD 1.3.6.1.4.1.6027.
PAGE 1543
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation remote systems table maintenance polls. Note that transmission of lldpRemTablesChan ge notifications are throttled by the agent, as specified by the 'lldpNotificationInte rval' object. 103 TR_LLDP_MED_T OPOLOGY_CHAN GE 1.0.8802.1.1.2.1.5.47 lldpXMedTopology 95.0.1 ChangeDetected lldp-ext-med.
PAGE 1544
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generates an event that is configured for sending SNMP traps. 108 TR_RMON_HC_RI SING_THRESHOL D 1.3.6.1.2.1.16.29.2.0. hcRisingAlarm 1 rfc3434.mib The SNMP notification that is generated when a high capacity alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps.
PAGE 1545
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation conflict resolved during audit 113 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_IN_PROGRESS 1.2.0.4 tProgress DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration commit is initiated 114 TR_BATCH_CONFI 1.3.6.1.4.1.6027.3.5. batchConfigCommi G_COMPLETE 1.2.0.5 tCompleted DELLNETWORKINGCOPY-CONFIGMIB.
PAGE 1546
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID 129 TR_VLT_ICL_STA TUS_CHANGE MIB File Explanation 1.3.6.1.4.1.6027.3.17 dellNetVLTIclStatu .2.0.2 sChange DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in InterConnect Link Status.The notification contains information on the new ICL status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 130 TR_VLT_PEER_ST 1.3.6.1.4.1.6027.3.
PAGE 1547
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation in Bandwidth usage of ICL Link, when it crosses the threshold above 80 %. The possible states are as follows: 0. Below threshold 1. Above threshold" 133 TR_VLT_DOMAIN _CFG_ERROR 134 1.3.6.1.4.1.6027.3.17 dellNetVLTDomain .2.0.6 ConfigError DELLNETWORKINGVIRTUAL-LINKTRUNK-MIB.
PAGE 1548
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation generated when the value of entLastChangeTim e changes. It can be utilized by an NMS to trigger logical/physical entity table maintenance polls. An agent should not generate more than one entConfigChange 'notification-event' in a given time interval (five seconds is the suggested default). A 'notification-event' is the transmission of a single trap or inform PDU to a list of notification destinations.
PAGE 1549
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation throttling or transmission loss. 139 TR_CHM_STACK_ UNIT_ROLE 1.3.6.1.4.1.6027.3.2 6.1.5.1.46 dellNetSysAlarmSta DELLckUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSIO N_MISMATCH 1.3.6.1.4.1.6027.3.2 6.1.5.1.23 dellNetSysAlarmCa DELLrdVersionMismatch NETWORKINGCHASSIS-MIB.
PAGE 1550
Table 9. SNMP Trap List (continued) TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNI T_DOWN 1.3.6.1.4.1.6027.3.2 6.1.5.1.30 dellNetSysAlarmPE UnitDown DELLNETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a PE Unit operational status is down 149 TR_SYSLOG_SER VER_CONNECTIO N_SUCCESSFUL 1.3.6.1.4.1.6027.3.3 0.1.1.2 Not Available Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SER VER_CONNECTIO N_FAILURE 1.3.6.1.4.
PAGE 1551
56 Stacking All commands in this chapter are specific to the Dell EMC Networking OS. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, see the Stacking S-Series Switches section in the Dell EMC Networking OS Configuration Guide. CAUTION: You cannot enable stacking simultaneously with virtual link trunking (VLT).
PAGE 1552
Version Description 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the members option. Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the running-config.
PAGE 1553
redundancy protocol Enable hitless failover for a protocol. Syntax Protocols Defaults redundancy protocol lacp Enter the LACP protocol xstp Enter one of the following protocols: STP, RSTP, MSTP, PVST. Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1554
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the hard reset option. Resetting the management unit is not allowed, and an error message displays if you try to do so. Resetting is a soft reboot, including flushing the forwarding tables. Starting with Dell EMC Networking OS version 7.8.1.0, you can run this command directly on the stack standby unit (standby master) to reset the standby. You cannot reset any other unit from the standby unit.
PAGE 1555
● Stack election is based on the priority or the MAC address of the stack units as in homogenous stacking. The stack-unit with the highest priority or MAC address is chosen as the master. ● TDR is a feature that is supported only on the S4048T-ON but not on the S4048-ON. If TDR is configured on the S4048T-ON, then mixed-mode stacking can be enabled only on the S4048T-ON switches. ● The hardware watchdog command is enabled only when the S4048T-ON act as master.
PAGE 1556
Apr 10 19:19:18: %STKUNIT2-M:CP %CHMGR-5-RELOAD: User request to reload the chassis syncing disks... done unmounting file systems... unmounting /f10/flash (/dev/wd0e)... unmounting /f10/ConfD/db (mfs:479)... unmounting /usr/pkg (/dev/wd0i)... unmounting /boot (/dev/wd0b)... unmounting /usr (mfs:29)... unmounting /force10 (mfs:24)... unmounting /lib (mfs:21)... unmounting /f10 (mfs:18)... unmounting /tmp (mfs:9)... unmounting /kern (kernfs)... unmounting / (/dev/md0a)... done rebooting...
PAGE 1557
Stack-unit ID: Stack-unit Redundancy Role: Stack-unit State: Stack-unit SW Version: Link to Peer: 1 Primary Active 1-0(0-4812) Up -- PEER Stack-unit Status ------------------------------------------------Stack-unit State: Standby Peer Stack-unit ID: 2 Stack-unit SW Version: 1-0(0-4812) -- Stack-unit Redundancy Configuration ------------------------------------------------Primary Stack-unit: mgmt-id 1 Auto Data Sync: Full Failover Type: Hot Failover Auto reboot Stack-unit: Enabled Auto failover limit: 3 ti
PAGE 1558
Usage Information Example Example (Status) Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. The following describes the show system stack-ports command shown in the following example. Field Description Topology Lists the topology of stack ports connected: Ring, Daisy chain, or Standalone.
PAGE 1559
4/54 5/53 5/54 6/53 6/54 Example (Topology) Related Commands 42 42 42 42 42 up up up up up up up up up up DellEMC#show system stack-ports topology Topology: Ring Interface Connection --------------------1/53 6/53 1/54 2/53 2/53 1/54 2/54 3/53 3/53 2/54 3/54 4/53 4/53 3/54 4/54 5/53 5/53 4/54 5/54 6/54 6/53 1/53 6/54 5/54 DellEMC# ● reset stack-unit – resets the designated stack member.
PAGE 1560
Related Commands ● reload – reboots Dell EMC Networking OS. stack-unit provision Preconfigure a logical stacking ID of a switch that joins the stack. This is an optional command that is executed on the management unit. Syntax stack-unit [stack-number] provision {model-identifier} Parameters Defaults stack-number Enter a stack member identifier of the switch that you want to add to the stack. model-identifier Enter the model identifier of the switch to be added as a stack member.
PAGE 1561
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810. 8.3.12.0 Reset command mode from EXEC to CONFIGURATION. The following message displays to confirm the command.
PAGE 1562
Version Description 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To reboot using the new image, use the upgrade boot system stack-unit command. Related Commands ● ● ● ● 1562 Stacking reload — reboots Dell EMC Networking OS. reset stack-unit — resets the designated stack member. show system — displays the status of all stack members or a specific member. show version — displays the current Dell EMC Networking OS version information on the system.
PAGE 1563
57 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/ Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember ● Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1564
Parameters Defaults interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. ● For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. none Command Modes ● EXEC ● EXEC Privilege Command History This guide is platform-specific.
PAGE 1565
Command Modes ● EXEC ● EXEC Privilege Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1566
● EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1567
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1568
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.
PAGE 1569
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter. It is possible, however, that some multicast control traffic may get dropped when storm control thresholds are exceeded.
PAGE 1570
Parameters Defaults pfc-llfc in Enter the keyword pfc-llfc to get the flow control traffic. The range is from 0 to 33554368 packets per second. shutdown Enter the keyword shutdown to shut down the port when the rate exceeds. none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1571
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series. Unknown Unicast Storm-Control is valid for Layer 2 and Layer 2/Layer 3 interfaces. storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only).
PAGE 1572
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
PAGE 1573
58 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1574
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1575
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
PAGE 1576
Parameters Defaults description Enter a description to identify the spanning tree (80 characters maximum). none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1577
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● protocol spanning-tree — enter SPANNING TREE mode on the switch.
PAGE 1578
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ● max-age — changes the wait time before STP refreshes protocol configuration information. ● hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1579
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters Defaults seconds Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1580
Command History Usage Information Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1581
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1582
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1583
Example Field Description “Designated port...” Displays the designated port ID. DellEMC# show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
PAGE 1584
Example (Guard) Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1585
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1586
59 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1587
Usage Information ● When you run the command, the system displays a message with the information directing to the URL for further information. ● Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. ● If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1588
Related Commands ● support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1589
support-assist activity Trigger an activity event immediately. Syntax Parameters support-assist activity {full-transfer | core-transfer} start now full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information. core-transfer Enter the keyword core-transfer to specify transfer of core files. Command Modes EXEC Privilege Command History Usage Information This guide is platform-specific.
PAGE 1590
Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. Introduced the core-transfer and event-transfer parameters. Usage Information 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. By default, each activity follows a set of default actions using a default schedule.
PAGE 1591
Parameters first-name (Optional) Enter the first name for the contact person. This is optional provided each contact person name is unique. To include a space, enter a space within double quotes. last-name Enter the last name for the contact person. To include a space, enter a space within double quotes. Command Modes SUPPORTASSIST Command History Usage Information This guide is platform-specific.
PAGE 1592
server Configure the name of the remote SupportAssist Server and move to SupportAssist Server mode. Syntax server {default | server-name} To delete a server, use the no server server-name command. Parameters Defaults default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred. To include a space, enter a space within double quotes. Default server has URL stor.g3.ph.dell.
PAGE 1593
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
PAGE 1594
Related Commands ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest show — view the list of action-manifest for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. action-manifest remove Remove the action-manifest file from Dell EMC Networking OS. Syntax action-manifest remove } Parameters local-file-name Enter the name of the local action-manifest file.
PAGE 1595
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. ● action-manifest get — copy an action-manifest file for an activity to the system. ● action-manifest install — configure the action-manifest to use for a specific activity. ● action-manifest remove — remove the action-manifest file for an activity. enable Enable a specific SupportAssist activity.
PAGE 1596
To remove the complete company contact information, use the no address command. Parameters city company- city province | region | state name (OPTIONAL) Enter the keyword city then the city or town for the company site. To include a space, enter a space within double quotes. (OPTIONAL) Enter the keyword province, region or state then the name of province, region or state for the company site. To include a space, enter a space within double quotes.
PAGE 1597
Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. territory Configure the territory and set the coverage for the company site.
PAGE 1598
Parameters primary email- address alternate emailaddress Enter the keyword primary then the primary email address for the person. Enter the keyword alternate then the alternate email address for the person. Command Modes SUPPORTASSIST PERSON Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM.
PAGE 1599
Related Commands ● preferred-method — configure the preferred method for contacting the person. preferred-method Configure the preferred method for contacting the person. Syntax Parameters Defaults preferred-method {email | no-contact | phone] email Enter the keyword email to specify email as preferred method. no-contact Enter the keywords no-contact to specify that there is no preferred method. phone Enter the keyword phone to specify phone as preferred method.
PAGE 1600
Usage Information Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. This command is optional for SupportAssist service configuration. SupportAssist Server Commands Dell EMC Networking OS supports the following SupportAssist Server mode commands. proxy-ip-address Configure a proxy for reaching the SupportAssist remote server.
PAGE 1601
Usage Information The passwords are stored encrypted in the running configuration. enable Enable communication with the SupportAssist server. Syntax enable To disable communication to a specific SupportAssist server, use the no enable command. Defaults Enabled Command Modes SUPPORTASSIST SERVER Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1602
Usage Information The URL should be formatted to follow the ISO format. show eula-consent Display the EULA for the feature. Syntax show eula-consent {support-assist | other feature} Parameters support-assist | other feature Enter the keywords support-assist or the text corresponding to other feature. Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1603
allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dells affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
PAGE 1604
preferred-method email time-zone zone +05:30 start-time 12:23 end-time 15:23 ! server Dell enable url http://1.1.1.1:1332 DellEMC# show support-assist status Display information on SupportAssist feature status including any activities, status of communication, last time communication sent, and so on. Syntax show support-assist status Command Modes EXEC Privilege Command History Example This guide is platform-specific.
PAGE 1605
60 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1606
Defaults end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year. The range is from 1993 to 2035. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to1440. The default is 60 minutes.
PAGE 1607
● week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time. ● first: Enter this keyword to start daylight saving time in the first week of the month. ● last: Enter this keyword to start daylight saving time in the last week of the month. Defaults start-day Enter the name of the day that you want daylight saving time to begin. Use English three letter abbreviations; for example, Sun, Sat, Mon, and so on. The range is from Sun to Sat.
PAGE 1608
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Updated the start-day and end-day options to allow for using the three-letter abbreviation of the weekday name. 6.1.1.0 Introduced on the E-Series. ● ntp trusted-key — configures a trusted key. ● clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. ● show clock — displays the current clock settings.
PAGE 1609
Usage Information Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8. debug ntp Display Network Time Protocol (NTP) transactions and protocol messages for troubleshooting.
PAGE 1610
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp authentication-key Specify a key for authenticating the NTP server.
PAGE 1611
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. After configuring the ntp authentication-key command, configure the ntp trusted-key command to complete NTP authentication. Dell EMC Networking OS versions 8.2.1.
PAGE 1612
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option. Syntax ntp control-key-passwd [encryption-type] password To delete the control key, use the no ntp control-key-passwd [encryption-type] password command.
PAGE 1613
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1614
ntp server Configure an NTP time-serving host. Syntax ntp server[vrf vrf-name] {hostname | ipv4-address | ipv6-address} [key keyid] [prefer] [version number] [minpoll] [maxpoll] Parameters vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to configure an NTP time-serving host corresponding to that VRF. ipv4-address | ipv6-address Enter an IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of NTP server. hostname Enter the host name of the server.
PAGE 1615
Usage Information Version Description 6.1.1.0 Introduced on the E-Series. You can configure multiple time-serving hosts. From these time-serving hosts, the Dell EMC Networking OS chooses one NTP host with which to synchronize. To determine which server is selected, use the show ntp associations command. Because many polls to NTP hosts can affect network performance, Dell EMC Networking recommends limiting the number of hosts configured.
PAGE 1616
Version Description 9.14.1.0 The support for configuring management interface is introduced in S4810 and S4820T. 9.13.0.0 Added support for configuring Management interface. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON.
PAGE 1617
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The number parameter in the ntp trusted-key command must be the same number as the number parameter in the ntp authentication-key command.
PAGE 1618
Example Example (Detail) Related Commands DellEMC#show clock 11:05:56.949 UTC Thu Oct 25 2001 DellEMC# DellEMC# show clock detail 12:18:10.691 UTC Wed Jan 7 2009 Time source is RTC hardware Summer time starts 02:00:00 UTC Sun Mar 8 2009 Summer time ends 02:00:00 ABC Sun Nov 1 2009 DellEMC# ● clock summer-time recurring — displays the time and date from the switch hardware clock. show ntp associations Display the NTP master and peers.
PAGE 1619
Field Description ● - means the peer is a candidate for selection. ● x means designated falsesticker by the intersection algorithm. Example (without ntp master configuration) Example (with ntp master configuration) remote Displays the remote IP address of the NTP peer. ref clock Displays the IP address of the remote peer’s reference clock. st Displays the peer’s stratum, that is, the number of hops away from the external time source. A in this column means the NTP peer cannot reach the time source.
PAGE 1620
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added support for VRF. 9.4.(0.0) Added support for VRF.
PAGE 1621
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp status command shown in the Example below. Field Description “Clock is...” States whether or not the switch clock is synchronized, which NTP stratum the system is assigned and the IP address of the NTP peer. “frequency is...
PAGE 1622
61 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1623
Usage Information The ip unnumbered command fails in two conditions: ● If the logical ip address is configured. ● If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address.
PAGE 1624
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
PAGE 1625
Parameters Defaults ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1626
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the C9010. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000.
PAGE 1627
tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header. Syntax tunnel hop-limit value To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters Defaults value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64.
PAGE 1628
Defaults Tunnel keepalive is disabled. Command Modes INTERFACE TUNNEL Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1629
Usage Information Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. To enable a tunnel interface, use this command.
PAGE 1630
Usage Information 1630 Tunneling Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the tunnel source anylocal command. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000.
PAGE 1631
62 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1632
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1633
Related Commands ● clear ufd-disable — re-enable downstream interfaces that are in a UFD-Disabled Error state. description Enter a text description of an uplink-state group. Syntax Parameters Defaults description text text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. none Command Modes UPLINK-STATE-GROUP Command History Example Related Commands This guide is platform-specific.
PAGE 1634
Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. If a 40G port is fanned-out into 10G ports, the range is entered as slot/sort/ subport-slot/port/subport. Defaults none Command Modes UPLINK-STATE-GROUP Command History Usage Information This guide is platform-specific.
PAGE 1635
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1636
If all upstream interfaces in an uplink-state group go down, all downstream interfaces in the same uplink-state group are put into a link-down state. Related Commands ● downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. ● uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. enable Enable uplink state group tracking for a specific UFD group.
PAGE 1637
Example Related Commands Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1638
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1639
Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/25(Up) Te 1/28(Up) Downstream Interfaces : Te 5/1(Up) Te 5/1(Up) Te 5/3(Up) Te 5/5(Up) Te 5/6(Up) Uplink State Group : 5 Status: Enabled, Down Upstream Interfaces : Te 1/1(Dwn) Te 1/3(Dwn) Te 1/5(Dwn) Downstream Interfaces : Te 5/2(Dis) Te 5/4(Dis) Te 5/11(Dis) Te 5/12(Dis) Te 5/13(Dis) Te 5/14(Dis) Te 5/15(Dis) Uplink State Group : 6 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 7 Status: Enabled,
PAGE 1640
An uplink-state group is considered operationally up if at least one upstream interface in the group is in the Link-Up state. An uplink-state group is considered operationally down if no upstream interfaces in the group are in the Link-Up state. No uplink-state tracking is performed when a group is disabled or in an operationally down state. To disable upstream-link tracking without deleting the uplink-state group, use the no enable command in uplink-state-group configuration mode.
PAGE 1641
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. You can assign physical port or port-channel interfaces to an uplink-state group. You can assign an interface to only one uplink-state group.
PAGE 1642
63 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1643
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. When packets are colored green; no packets are dropped.
PAGE 1644
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. S4048–ON Syntax dei mark {green | yellow} {0 | 1} Parameters Defaults 0|1 Enter the bit value you want to map to a color. green | red | yellow Choose a color: ● Green: High priority packets that are the least preferred to be dropped.
PAGE 1645
member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command. Parameters Defaults interface Enter the following keywords and the interface information: ● For a Port Channel interface, enter the keywords port-channel, and then a number.
PAGE 1646
stack-group-id Enter the stack group ID. The range is from 0 to 16. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1647
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to enabling this command, to place the interface in Layer 2 mode, enter the switchport command.
PAGE 1648
Version Description E-Series original Command Usage Information Prior to disabling the stackable VLAN feature, remove the members. To view the stackable VLANs, use the show vlan command in EXEC Privilege mode. Stackable VLANs contain members, designated by the M in the Q column of the command output. If you enabled VRF, you cannot enable the stacked VLAN feature using this command. If you enabled IGMP snooping, you cannot enable the stacked VLAN feature using this command.
PAGE 1649
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. You can separate the C-Tag values by commas or dashed ranges. In the case of conflicts, dynamic mode CoS overrides any Layer 2 QoS configuration.
PAGE 1650
Usage Information For specific interoperability limitations regarding the S-Tag TPID, see the Dell EMC Networking OS Configuration Guide. The four characters you may enter are shown in the following table. Related Commands Number Resulting TPID 1 0x0001 10 0x0010 81 0x0081 8100 0x8100 ● portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays.
PAGE 1651
Version Description E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, use the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. In Example 1, a VLAN-Stack trunk port is configured and then made part of a single-tagged VLAN. In Example 2, the tag protocol identifier (TPID) is set to 88A8.
PAGE 1652
DellEMC(conf-if-te-5/1)# vlan-stack trunk DellEMC(conf-if-te-5/1)# exit DellEMC(config)# interface vlan 10 DellEMC(conf-if-vlan)# vlan-stack compatible DellEMC(conf-if-vlan)# member Te 4/1, Te 3/10, TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# interface vlan 30 DellEMC(conf-if-vlan)# untagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# DellEMC(config)# interface vlan 40 DellEMC(conf-if-vlan)# tagged TenGi 5/1 DellEMC(conf-if-vlan)# exit DellEMC(config)# 1652 VLAN Stacking
PAGE 1653
64 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • ip vrf ip http vrf description ip vrf forwarding ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip vrf Create or delete a customer VRF.
PAGE 1654
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters Defaults management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 1655
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
PAGE 1656
you assign two interfaces to the same VRF, you cannot configure overlapping IP subnets or the same IP address to them. Example DellEMC# configure terminal DellEMC(conf)# ip vrf red DellEMC(conf-vrf)# description "Red Network" DellEMC(conf-vrf)# show config ! ip vrf red 4 description "Red Network" DellEMC(conf-vrf)# DellEMC(conf-if-te-1/45)# int te 7/46 DellEMC(conf-if-te-1/46)# no shut DellEMC(conf-if-te-1/46)# ip vrf forwarding red DellEMC(conf-if-te-1/46)# ip add 100.1.1.
PAGE 1657
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, you can use the ip route-export tag command without specifying the route-map attribute. This action exposes source VRF routes to various other VRFs, which then import these routes using the ip route-import tag command.
PAGE 1658
Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. ● ip route-export – exports routes to another VRF. ipv6 route-export Enables route leaking between VRFs.
PAGE 1659
Only active routes are eligible for leaking. For example, if one VRF has two routes corresponding to BGP and OSPF, in which the BGP route is not active, the OSPF route takes precedence over BGP. Even though the target VRF has specified filtering options to match BGP, the BGP route is not leaked as that route is not active in the source VRF. Related Commands ● ipv6 route-import – imports IPv6 routes from another VRF.
PAGE 1660
Parameters bgp Enter the keyword bgp to leak or share routes corresponding to the BGP protocol. isis Enter the keyword isis to leak or share routes corresponding to the ISIS protocol. ospf Enter the keyword ospf to leak or share routes corresponding to the OSPF protocol. connected Enter the keyword connected to leak or share connected routes corresponding to the VRF. static Enter the keyword static to leak or share static routes corresponding to the VRF.
PAGE 1661
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. ● ip route-import — import routes from another VRF.
PAGE 1662
To remove the limit on the maximum number of routes used, use the no maximum dynamic-routes command. Parameters limit Maximum number of routes allowed in a VRF. The valid range is from 1 to 16,000 (or maximum allowable for that platform if a smaller value). warningthreshold The warning threshold value is a percentage of the limit value. When the number of routes reaches the specified percentage of the limit, a warning message appears. The valid range is from 1 to 100.
PAGE 1663
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 1664
Usage Information Example 1664 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. This command displays information from the running-config corresponding to either a specific VRF or all the VRFs in the system.
PAGE 1665
65 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1666
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1667
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1668
Usage Information Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. You must configure the VLT port channel interface which is connecting to the remote VLT domain as peer-domain-link.
PAGE 1669
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. S4048–ON Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1670
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1671
66 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1672
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} Parameters Defaults ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1673
clear vlt statistics Clear the VLT operation statistics. Syntax Parameters clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP.
PAGE 1674
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax delay-restore Parameters Defaults delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1675
This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap). Defaults 60 seconds Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1676
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. LACP on the VLT ports (on a VLT switch or access device), which are members of the VLT, are not brought up until the VLT domain is recognized on the access device.
PAGE 1677
Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1678
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan option. 8.3.8.0 Introduced on the S4810. To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option.
PAGE 1679
peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 65535. The default value is infinity. Command Modes VLT DOMAIN (conf-vlt-domain) Default Infinity Command History This guide is platform-specific.
PAGE 1680
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1681
Usage Information Example (Brief) Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell EMC Networking OS version number. VLT version numbers begin with odd numbers.
PAGE 1682
Example Version Description 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays counter information.
PAGE 1683
Usage Information Example Example (igmpsnoop) Example (igmpsnoop interface port-channel) If you do not add a parameter such as arp or mac, the output displays all the counters.
PAGE 1684
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1685
-----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.2) VLAN 15 DellEMC# --------VLAN 6 te 1/5 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show mismatch in VXLAN instance parameters. 9.10(0.
PAGE 1686
VLAN to VNI config mismatch -------------------------------------Vlan-ID Local VNID Peer VNID -----------------------------10 10 11 11 12 12 13 13 - VXLAN enabled status on VLT Port Channels ------------------------------------------Local-Lag Status Peer-Lag Status -----------------------------300 Disable 100 Disable 700 Enable 812 Disable 999 Disable 888 Disable Local VTEP IP mismatch ------------------------------------------------------------------Local Node “Local VTEP IP” Remote Node “Local VTEP IP”
PAGE 1687
Local Lag --------128 Peer Lag Local VLANs -------- ----------128 4094 Peer VLANs ---------100 DellEMC# show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured. Command Modes EXEC Command History Example This guide is platform-specific.
PAGE 1688
show vlt statistics Displays VLT operations statistics. Syntax show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters Default arp Enter the keyword arp to display the ARP VLT statistics. domain Enter the keyword domain to display the domain VLT statistics. igmp-snoop Enter the keywords igmp-snoop to display the IGMP snooping VLT statistics. mac Enter the keyword mac to display the VLT MAC addresses VLT statistics.
PAGE 1689
VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg Response rcvd: 1 IGMP PDU Tunnel Pkt sent: 5 IGMP PDU Tunnel Pkt rcvd: 10 IGMP Tunnel PDUs sent: 10 IGMP Tun
PAGE 1690
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1691
unit-id Configure the default unit ID of a VLT peer switch. Syntax Parameters Defaults unit-id [0 | 1] 0|1 Configure the default unit ID of a VLT peer switch. Enter 0 for the first peer. Enter 1 for the second peer. Automatically assigned based on the MAC address of each VLT peer. The peer with the lower MAC address is assigned unit 0; the peer with the higher MAC address is assigned unit 1. Command Modes VLT DOMAIN Command History Usage Information This guide is platform-specific.
PAGE 1692
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 1693
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. show vlt private-vlan Display the private VLAN (PVLAN) associated with the VLT LAG for VLT peer nodes. Syntax show vlt private-vlan Command Modes EXEC Command History Usage Information This guide is platform-specific.
PAGE 1694
67 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
PAGE 1695
Usage Information Use this command to clear the remote VTEP and access port statistics. clear mac-address-table dynamic Clear the MAC address table of specific or all MAC address learned dynamically.
PAGE 1696
Defaults Disabled Command Modes VXLAN INSTANCE Command History Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1697
Version Description 9.10(0.1P10)) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. Usage Information You must configure feature VXLAN to configure VXLAN-instance. Related Commands vxlan-instance — Enable VXLAN Instance configuration on the platform. fail-mode Configures failure-mode on the platform. Syntax fail-mode secure To disable the fail-mode secure, use the no fail-mode securecommand.
PAGE 1698
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. vxlan-instance — Enable VXLAN Instance configuration on the platform. local-vtep-ip Set the local IP Address to be used as the source IP for VXLAN tunnels.
PAGE 1699
Version Description 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. Usage Information The retry interval value caps at the value configured on the max-backoff. Related Commands vxlan-instance — Enable VXLAN Instance configuration on the platform. peer-ovsdbserver-ip Specify the IP address of the peer OVSDB server in a VLT setup.
PAGE 1700
Usage Information Use this command to associate a specific VNID to a remote VTEP. Provide a valid profile name while associating to the remote VTEP. NOTE: The remote VTEP IP Address cannot be any of the local IP Addresses configured in the switch. vnid Associate a range of VNID numbers to a specific VNI profile. Syntax vnid VNID-Range To remove the association, use the no vnid command. Parameters Defaults VNID-Range Enter the range of VNIDs that need to be members of the specific VNI profile.
PAGE 1701
vxlan-instance Enable VXLAN Instance configuration on the platform. Syntax vxlan-instance instance ID [nsx | nuage | static] To delete vxlan-instance from the system, use no vxlan-instance instance ID command. Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1. nsx Enter the keyword nsx to connect to an NSX controller. NOTE: When no keyword is specified, the nsx option is applied. Defaults nuage Enter the keyword nuage to connect to a Nuage controller.
PAGE 1702
To unconfigure VAP, use the no vxlan-instance 1 command. Parameters Defaults instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON.
PAGE 1703
Internal Loopback: DellEMC(conf-if-te-1/2/2/3)#sho c ! interface TenGigabitEthernet 1/2/2/3 description connected IXIA card 1 port 14 vxlan-instance 1 Disable VXLAN Instance: DellEMC(conf)#no vxlan-instance 1 Related Commands feature vxlan — Enable VXLAN configuration globally on the platform. vxlan-instance static Enable VXLAN instance configuration to be static on the platform.
PAGE 1704
vxlan-vnid Associate VNID to VLAN. Syntax vxlan-vnid VNID To remove the association, use the no vxlan-vnid command. Parameters Defaults VNID Enter the logical network identifier. None Command Modes INTERFACE VLAN Command History Usage Information This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048, S4048T, S6000, S6010, S6100, and Z9100.
PAGE 1705
remote-vtep-ip 2.2.2.2 vni-profile ni1 Controller Mode: DellEMC#show running-config vxlan ! feature vxlan ! vxlan-instance 1 gateway-ip 3.3.3.3 fail-mode secure controller 1 192.168.122.6 port 6632 ssl no shutdown Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance Displays information related to Network Virtualization Overlay (NVO) Gateway. Syntax Parameters show vxlan vxlan-instance instance ID instance ID Enter the VXLAN instance ID.
PAGE 1706
show vxlan vxlan-instance logical network Displays logical network information related to Network Virtualization Overlay (NVO) Gateway. Syntax show vxlan vxlan-instance instance ID logical-network [name name] Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. name name (OPTIONAL) Enter the keyword name and enter the name of VXLAN logical network up to a length of maximum 30 characters.
PAGE 1707
A.B.C.D Defaults Enter the IP address of the VTEP. Disabled Command Modes VXLAN INSTANCE Command History Example Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010– ON, S6100–ON, and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1708
Example Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. DellEMC#show vxlan vxlan-instance 1 statistics interface fortyGigE 1/49 100 Port : Fo 1/49 Vlan : 100 Rx Packets : 13 Rx Bytes : 1317 Tx Packets : 13 Tx Bytes : 1321 Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance statistics remote-vtep-ip Displays VXLAN statistics for a specific VXLAN tunnel.
PAGE 1709
show vxlan vxlan-instance unicast-mac-local Displays the information of the local unicast MAC associated with the logical network related to Network Virtualization Overlay (NVO) Gateway. Syntax Parameters show vxlan vxlan-instance instance ID unicast-mac-local [logical—network name | vnid VNID] instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. name (Optional) Enter the name of VXLAN logical network with a maximum length of 30 characters.
PAGE 1710
name (Optional) Enter the name of VXLAN logical network with a maximum length of 30 characters. vnid VNID (Optional) Enter the keyword vnid and then enter the ID of the VXLAN. The range is from 1 to 16777215. Command Modes ● EXEC ● EXEC Privilege Command History Example Related Commands This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.
PAGE 1711
Example DellEMC# show vxlan 1 vtep-vni-map Remote Vtep IP : 10.10.10.10 VNI profile : Profile1 VNID count : 4 VNID list : 100, 200, 300, 400 Remote Vtep IP VNI profile VNID count VNID list : : : : 10.10.10.
PAGE 1712
68 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1713
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1714
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax clear counters vrrp [vrrp-id] [ipv6] Parameters vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1715
between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups.
PAGE 1716
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group. Syntax description text To delete a VRRP group description, use the no description command. Parameters Defaults text Enter a text string up to 80 characters long.
PAGE 1717
To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1718
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1719
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command.
PAGE 1720
If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration. Syntax show config [verbose] Parameters verbose (OPTIONAL) Enter the keyword verbose to view all the VRRP group configuration information, including default information. Command Modes VRRP Command History Example This guide is platform-specific.
PAGE 1721
Parameters vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups. interface type (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1722
Item Description ● Y = Preempt is enabled. ● N = Preempt is not enabled. Example (Brief) Usage Information State Displays the operational state of the interface using one of the following: ● NA/IF (the interface is not available). ● MASTER (the interface associated with the MASTER router). ● BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router.
PAGE 1723
Example Example (VRRP VRF) DellEMC> show vrrp -----------------TenGigabitEthernet 1/3, VRID: 1, Net: 10.1.1.253 VRF: 0 default State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
PAGE 1724
track Monitor an interface and lower the priority value of the VRRP group on that interface if it is disabled. Syntax track interface [priority-cost cost] To disable monitoring, use the no track interface command. Parameters Defaults interface (OPTIONAL) Enter the following keywords and the interface information: ● For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1725
... ip-address12 Defaults (OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted decimal format. Separate the IP addresses with a space. The IP addresses must be on the same subnet as the interface’s primary IP address. Not configured. Command Modes VRRP Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1726
Version Description 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information This command applies to a single interface. When you use this command with the vrrp delay reload command, the later timer rules VRRP enabling.
PAGE 1727
Usage Information This command applies to all the VRRP interfaces on a system. When you use this command with the vrrp delay minimum command, the later timer rules VRRP enabling. For example, if vrrp delay reload is 600 and vrrp delay minimum is 300: ● When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 1728
version Set the VRRP protocol version for the IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters Defaults 2 Enter the keyword 2 to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the keyword 3 to specify VRRP version 3 as defined by RFC 5798, Virtual Router Redundancy Protocol. both Enter the keyword both for in-service migration from VRRP version 2 to VRRP version 3.
PAGE 1729
● debug vrrp ipv6 ● show vrrp ipv6 ● vrrp-ipv6-group The following commands apply to IPv4 and IPv6: ● advertise-interval ● description ● disable ● hold-time ● preempt ● priority ● show config ● virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups. Syntax Parameters clear counters vrrp ipv6 [vrid | vrf vrf-name] vrid (OPTIONAL) Enter the number of an IPv6 VRRP group; range is from 1 to 255.
PAGE 1730
● For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/ [subport]. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as clear counters interfaces interfacetype 1/1/1 - 1/1/4. debug vrrp ipv6 Enable VRRP debugging.
PAGE 1731
Usage Information If you do not specify an option, debugging is active on all interfaces and all VRRP groups. show vrrp ipv6 View the active IPv6 VRRP groups. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group. Syntax Parameters show vrrp ipv6 [vrid] [interface] [brief] [vrf vrf-name] vrid (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255.
PAGE 1732
Line starting with Description VRF VRF instance to which the VRRP group interface belongs. State: master... Displays the interface’s state: ● Na/If (not available) ● master (MASTER virtual router) ● backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:... Displays additional VRRP configuration information: ● Hold Down displays the hold down timer interval in seconds.
PAGE 1733
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1734
69 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1735
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax Parameters Defaults crypto ca-cert install path path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1736
● secadmin The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1737
email email- address Defaults (OPTIONAL) Enter the keyword email followed a valid email address used for communication with the organization. validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect. For self-signed certificates, if validity is not specified, it defaults to 3650 days, or 10 years. length length (OPTIONAL) Enter the keyword length followed by a bit length value.
PAGE 1738
Parameters cert-file Enter the keyword cert-file to specify that the certificate needs to be downloaded. cert-path Enter the path where the certificate is locally stored. The path can be a full path or a relative path. If the system accepts this path, a notification is sent indicating the location where the certificate file is stored. Following are example of a path that you can specify: flash://certs/s4810-001-request.crtand usbflash:/certs/s4810-001-cert.
PAGE 1739
If the system is in non-FIPS mode, the certificate will be installed as the non-FIPS certificate. When FIPS mode is enabled/disabled, the certificates (and keys) are switched by the system. Related Commands ● crypto ca-cert install crypto x509 ocsp Configures the OCSP behavior. Syntax Parameters Defaults crypto x509 ocsp [nonce] [sign-requests] nonce Enter the keyword nonce to use the nonce feature for the OCSP requests to OCSP responder communication.
PAGE 1740
Command Modes ● CONFIGURATION Mode Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Related Commands Version Description 9.11.0.0 Introduced this command.
PAGE 1741
tcp Enter the keyword tcp to enable TCP. udp Enter the keyword udp to enable UDP. vrf vrf-name Enter the keyword vrf followed by the name of the VRF. sha1 fingerprint Enter the keyword sha1 followed by the finger print. This option is only available when the secure option is configured. This new option enables the Syslog feature to compare the received certificate’s sha-1 fingerprint against this configured sha-1 fingerprint.
PAGE 1742
Usage Information Version Description 9.11.0.0 Introduced this command. The following RBAC roles are allowed to issue this command: ● sysadmin ● secadmin When you use this command, the device maps the current certificate context in the certificate store to a CA certificate through the subject key identifier field. The subject key identifier field contains the SHA-1 hash of the CA’s public key. This configuration provides a way to uniquely identify a CA and associate it with any CA-specific settings.
PAGE 1743
Related Commands ● crypto x509 ocsp ocsp-server prefer Configures OCSP responder preference. You can configure the preference or order that the CA or a device should follow while contacting multiple OCSP responders. Syntax ocsp-server prefer Defaults None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1744
show crypto cert Displays the certificate information that is specified. Syntax show crypto cert {path} Parameters Defaults path (OPTIONAL) Enter the path to a local file where a certificate chain is stored in PEM format. If a path is not specified, display the certificate that is currently installed on the system. None. Command Modes EXEC Privilege Command History This guide is platform-specific.