Release Notes

PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/
M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA
Release Notes
System Firmware Version 5.1.1.7 Page 43
Release 4.1.1.9
Summary
User Impact
Resolution
Affected
Platforms
PC7048R-RA switch has boxes
req cpu process 38-54%
utilization with single power
supply.
PC7048R-RA switch has cpu process boxes
req running between 38-54 % utilization if
it’s running either only with primary or
secondary power supply.
Corrected CPU utilization
issue when running with one
power supply.
PC7048R-RA
Router crashes on OSPF
network type change.
The switch can crash when changing the
configuration from the default of broadcast
to point-to-point.
Corrected process
synchronization problem
All Platforms
Occasional crash when
configuring VRRP.
With routing globally disabled, bouncing
VRRP on a host interface occasionally
causes a crash.
Correct the transition
between routing being
disabled and routing being
enabled.
All Platforms
Cannot create Dynamic LAG
with Interface range command
Dynamic LAG cannot be created from CLI
using interface range command.
Correct the command
syntax to "auto " instead of
"active"
All Platforms
PC8024 cannot forward
packets on port9 to port16
while linked on at 100Mb.
PC8024 cannot forward packets on port9
to port16 while linked on at 100Mb.
Correct interoperability
problem between the PHY
and the switching core.
PC8024
PC8024F
Show fiber-ports optical-
transceiver is not displaying
the correct interface numbers.
Instead of reporting on exact ports that had
modules, diagnostics were reported on the
ports that did not have modules
Corrected register problem
when accessing the SPF+
ports
PCM8024
VRRP routing instances
increased to 50.
VRRP routing instances increased to 50. Increased VRRP routing
instances table.
All Platforms
DHCP on in-band and out of
band ports
The warning message about IP address
conflict is not printed in case DHCP is
configured on in-band and out-band ports
and they both receive an IP address from
one subnet.
Add warning message in
case offered IP address is
conflicting with the
configured one on another
port
All Platforms
Config commands did not
migrate correctly from version
3.1.5.13
Command "spanning-tree mode mstp"
doesn't migrate correctly from version
3.1.5.13.
Correct the command tree to
migrate the old syntax.
All Platforms
Auto-neg option via Web UI is
not grayed out for 10Gb fiber
ports.
Auto-neg option via Web UI is not grayed
out for 10Gb fiber ports for the PCM8024-
k.
Corrected the Web UI. PCM8024-k
Simple mode, VLAN setting
not active when a port is
moved to another group
if a port is moved from one aggregation
group to other, VLAN settings are
retained but not applied until reboot.
Correct initialization when
port is moved.
PCM6220
Unable to configure secure
SSH from web interface.
Error message 'sshcfg_load start' missing
is returned.
Corrected Web page error. All Platforms
Secure HTTP Random
Characters
Random characters populate the Secure
HTTP web page.
Corrected Web page data
initialization.
All Platforms
IP PIMSM BSR/RP Mapping
is not robust
When the RP or the BSR changes, the data
traffic may get affected and in some case
get software forwarded.
Corrected RP join
processing.
All Platforms
Error messages when issuing a
show statistics command while
traffic running.
Accessing unsupported counters causes
error messages to be displayed.
Change the logging priority
of the messages for
unsupported counters so that
they are not output.
All Platforms