53-1001791-01 January 31, 2010 Mid-Mount Rack Kit (Switch) Installation Procedure Supporting PowerConnect B-200E, 300, 4100, 4900, 5000, 5100, 5300, 7500-series, 7600, 7800, 8000, AP7420, and VA-40FC 53-1001791-01 *53-1001791-01*
Notes, Cautions, and Warnings NOTE A NOTE indicates important information that helps you make better use of your computer. CAUTION See the safety and regulatory information that shipped with your system. For additional regulatory information, see the Regulatory Compliance Homepage on www.dell.com at the following location: www.dell.com/regulatory_compliance. CAUTION A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
In this guide • Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Installation requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Tool requirements and parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Attaching front brackets to switch. . . . . . . . . .
• Ensure that an electrical branch circuit with the following characteristics is available: - Required voltage and frequency as indicated in the hardware reference manual. (200-230 VAC is always preferred) - Protection by a circuit breaker in accordance with local electrical codes. Supply circuit, line fusing, and wire size that conform to the electrical rating on the switch nameplate. Grounded outlet compatible with the power cord and installed by a licensed electrician.
1 scale: 3/16" = 1" 2 3 (12x) (8-32 x 5/16 in.) 4 5 (8x) (6-32 x 1/4 in.) (8x) (10-32 x 5/8 in.) 6 (8x) (10-32) 1 Bracket, front right Bracket, back left 4 Screw, 6-32 x 1/4 in., flathead Phillips 2 Bracket, front left Bracket, back right 5 Screw, 10-32 x 5/8 in., panhead Phillips 3 Screw, 8-32 x 5/16 in.
Attaching front brackets to switch Complete the following steps to attach the front brackets to the switch. 1. Position the right front bracket (Item 1) with the flat side against the right side of the switch (Figure 2). 2. Insert two 8-32 x 5/16 in. screws (Item 3) into one of the pairs of vertically aligned holes in the bracket and then into the pair of holes on the side of the switch.
6 1 1 Bracket, front righ 5 Screw, 10-32 x 5/8 in., panhead Phillips FIGURE 3 6 5 Retainer nut, 10-32 Attaching front rails to a cabinet Attaching rear brackets to a cabinet Complete the following steps to attach the rear brackets to the cabinet. 1. Position the right rear bracket (Item 2) in the right rear of the switch (Figure 4). 2. Attach the brackets using three 6-32 x 1/4 in. screws (Item 4) and retainer nuts (Item 6). 3.
1 4 6 2 1 Bracket, front right 4 Screw, 6-32 x 1/4 in., flathead Phillips 2 Bracket, rear right 6 Retainer nut, 10-32 FIGURE 4 Attaching the rear brackets to a cabinet Attaching rear bracket to switch Complete the following steps to attach the rear brackets to the switch. 1. Align the right rear bracket (Item 2) to the right rear of the switch and using two 10-32 x 5/8 in. screws (Item 5) attach the bracket to the switch (Figure 5). 2.
5 5 Screw, 10-32 x 5/8 in.
Mid-Mount Rack Kit (Switch) Installation Procedure 53-1001791-01
