Scalable HD Over IP Solution for Networked Distribution using JPEG2000 compression WyreStorm HD over IP Solutions Part Number NHD-IP-TX NHD-IP-RX Instruction Manual Thank you for choosing this WyreStorm product. Please read these instructions carefully before installing to avoid complications later.
CONTENTS AND INTRODUCTION Contents 1 Introduction 2 Features 3 Safety Precautions 4 Package Contents 5 Specifications 6 Panel Description: i. NHD-IP-TX Transmitter ii. NHD-IP-RX Receiver 7 Connection 8 Typical Application i. One Transmitter to One Receiver ii. One Transmitter to Multiple Receivers iii. Multiple Transmitters to Multiple Receivers iv. Video Wall 9 Switch Settings and Requirements 10 NHD-IP-CTL Browser Configuration & Control i. Matrix Switching Commands ii.
d RJ45 h display caded). ependently s for ultaneously ption. tions. h additional settings if and • JPEG2000 lossless video compression • HDMI Pass-through • Extend transmission distance to 100m/328ft from the sources at 1080p • Supports all high definition resolutions: 720p, 1080i, • Protection against ESD (electrostatic discharge) included within 1080p up to 1920x1200 resolution at 60fps. the unit to further stabilise transmission.
SPECIFICATIONS 5. Specifications Data Rate 150Mbps Maximum Maximum Transmission Distance 100m/328ft I/O Connections NHD-IP-TX Transmitter 1 x USB (B type) 1 x RJ45 port 1 x HDMI IN 1 x HDMI OUT 1 x RS232 (3.5mm phoenix) NHD-IP-RX Receiver 4 x USB (A type) 1 x RJ45 port 1 x HDMI OUT 1 x RS232 1 x AUDIO OUT Power Supply 12V DC, 5.5mm Power Consumption 5 Watts Input Video Signal 1.
Panel Description i. NHD-IP-TX Transmitter 1 2 PANEL DESCRIPTION 6. ii.
CONNECTION 7. Connection Key cat 5e/6 100m/328ft hdmi 8 USB 6 RS232 Controller 6 6 7 7 1 Tx Tx rx 5 3 Blu Ray rx 5 4 3 4 2 KVM Cat5e Wiring Guide The quality of termination for every RJ45 is essential. Poor terminations leads to intermittent performance and longer install times.
8 8. TYPICAL APPLICATION Plug in 12V DC power supplies to the TX & RX units. (Not required to the RX if using PoE as power to will be supplied via the TX). Plug in 5V DC power supply to the CTL - unit if in use. Typical Application i. One Transmitter To One Receiver Transmitter KVM Key cat 5e/6 100m/328ft hdmi receiver USB ii.
iii. Multiple Transmitters To Multiple Receivers TYPICAL APPLICATION Blu - Ray Transmitter Blu - Ray Media server Transmitter Transmitter Pc receiver receiver receiver receiver iv. Video Wall Blu - Ray Transmitter receiver receiver Transmitter receiver receiver receiver 8 Technical Support: support@wyrestorm.
Switch Settings & Requirements NetworkHD can be operated with any Layer 2 Gigabit Smart Switch provided the overall switching capacity or backplane capacity of the switch meets the requirements of the number of transmitters/receivers you have on your network. Each NHD-IP-TX transmitter will produce up to 150Mb/s of data > therefore 10 x transmitters will require 10 x 150Mb/s = 1.5 Gbps.
Hewlett Packard 1810 series switches NHD-IP-CTL BROWSER CONFIGURATION & CONTROL Navigate to the switches web browser configuration interface and follow these steps: 1 Navigate to Network > IGMP Snooping > Advanced and set IGMP Snooping to Enable and select Apply. 2 In Network > IGMP Snooping > Advanced click the icon under Operation and in the following screen set both IGMP Snooping and Querier to Enabled. Click Apply.
Tabs at the top of the Home Screen page are used to access settings for Matrix, TX/RX Settings and System Settings. All pages display Telnet API boxes where commands can be entered from the NetworkHD API. 1 Click the Load Matrix button, and the table of devices will appear with TX units across the top and the RX down the left hand side. 2 Press the box that links each TX & RX to test switching of the video to each RX.
ii. TX/RX Settings NHD-IP-CTL BROWSER CONFIGURATION & CONTROL The TX/RX Settings section enables IP settings and alias of each TX and RX to be configured as well as rebooting the system and factory resetting the devices.
GUI Element Description Factory Default Restore TX/RX to factory default settings Reboot Reboot TX/RX 1. CTL Settings contains the settings for the IP control box itself, comprising of two separate network connections for communication with RX/TX devices and communication to the PC/control system. 2. Each setting must be on the same subnet as other devices to enable communication between all devices. 3.
3 NETWORKHD CONSOLE CONFIGURATION Click Start menu, go to Control Panel > Network and Sharing center > Change Adapter Settings > Local Area Connection. Right click and choose Properties. 4 Highlight Internet Protocol Version 4 (TCP/IPv4) then click Properties 5 Check Use the following IP address, for the IP address enter 169.254.xx.xx (if unsure use 169.254.2.5) Enter subnet mask number 255.255.0.0 Click OK, then click OK again. ii.
NETWORKHD CONSOLE CONFIGURATION 2 When the search is complete authenticated devices will be displayed in the Devices area. Restore is checked by default. Attention If no devices are found, please refer to #1 of the Troubleshooting section of this guide. iii. Setting Device Parameters Right click a device in Devices - all available functions are displayed in the pop-up menu. Operation Description Modify Modify device parameters - available only when a single device is selected.
iv. Device Settings NETWORKHD CONSOLE CONFIGURATION Right click a device in Devices and choose Modify, the Device settings dialog box is displayed.
NETWORKHD CONSOLE CONFIGURATION Click OK and details of the 2 x 2 scene will appear in the window. vi. Sample Video Wall Set Up Video Wall mode combines multiple display (RX) devices to show a complete video source. Select multiple display devices in the scene setting interface, and combine the cells as follows to configure the Video Wall – see below for 2 x 2 scene as an example: Preparation 1. Two NHD-IP-TX Transmitters 2. Four NHD-IP-RX Receivers 3. A layer 2 Smart Ethernet Switch 4.
1 Connect the Blu-ray player to HDMI IN port of TX1 with an HDMI cable and connect HDMI OUT port of TX1 to HDMI IN port of TX2. NETWORKHD CONSOLE CONFIGURATION 2 Connect TX1 and TX2 to the Switch with Ethernet cables. 3 Connect RX1, RX2, RX3, and RX4 to the Switch with Ethernet cables. 4 Connect HDMI OUT port of RX1, RX2, RX3, RX4 to the display devices with HDMI cables. 5 Power on all devices vii.
Combine: Right click any cell > choose Select All. NETWORKHD CONSOLE CONFIGURATION 2 The highlight color will change to indicate all cells have been selected Technical Support: support@wyrestorm.
3 Now right click the cells again and select Combine. NETWORKHD CONSOLE CONFIGURATION 4 Confirm Wall Properties: Clicking Combine brings up the Video Wall Properties screen. Check Multi Host Mode > input a name of choice and click OK. 20 Technical Support: support@wyrestorm.
NETWORKHD CONSOLE CONFIGURATION vii. Video Wall Properties GUI Element Description Name Name the Video Wall Single Host Mode Single video-source mode - assign same video-source to all cells. Multi Host Mode Multiple video-source mode – assign different cell rows with different video sources (recommended setting) OW, OH, VH, VW Set Bezel and Gap Compensation of displays viii. Configuration File Management When closing the configuration tool, the software will save a configuration file default.
ix. Log TROUBLESHOOTING 12. Troubleshooting 1) If NetworkHD software console cannot find any devices on the network - If following the network settings advice in sections 10 through 14 above does not yield any devices, check your Windows Firewall settings. Using Windows 7 as an example (Other versions of Windows may differ): • Click Start menu, go to Control Panel > System and Security > Windows Firewall > Allowed Programs, highlight HDMI over IP Console, check Home/Work (Private) and Public.
• Check the Web browser. We recommend you use Firefox, Opera, Safari Internet Explorer 11 or Chrome. If the problem persists, try to upgrade you browser to the latest version. • Perform a reset on the NHD-IP-CTL by holding down the reset button on the front of the device.
ADDITIONAL INFORMATION, FAQS, MAINTENANCE AND PROVIDED SERVICE 13. Additional Information Further information about NetworkHD including system configuration & switch configuration guides as well as control drivers and Enado templates can be found at wyrestorm.com. 14. FAQs What compression technology is utilised in NetworkHD? NetworkHD utilises high quality JPEG2000 compression algorithm to produce very high quality images that are indistinguishable from the original at normal viewing distances.
Mail-in-service When shipping the unit, carefully pack and send it prepaid, with adequate insurance and preferably in the original packaging. Please include a document or letter detailing the reason for return and include a daytime telephone number and/or email address where you can be contacted.
INSTALLATION REFERENCE LOG 20. Installation Reference Log NHD-IP-TX TRANSMITTER TX# IP ADDRESS ALIAS ADDITIONAL INFO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 26 Technical Support: support@wyrestorm.
INSTALLATION REFERENCE LOG NHD-IP-RX RECEIVER TX# IP ADDRESS ALIAS ADDITIONAL INFO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Technical Support: support@wyrestorm.
wyrestorm.com WyreStorm Offices US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133 Tel: + 901 384 3575 Fax: + 901 384 3574 Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK Tel: +44 (0) 1793 230 343 Fax: +44 (0) 1793 230 583 WyreStorm Technical Support US: +86 6677 0053 UK:- +44 (0) 1793 238 338 Email: support@wyrestorm.com WyreStorm Technologies reserve the right to change physical appearance or technical specification of this product at any time. Visit wyrestorm.