User guide

AirWave 7.5.6 | Release Notes 11
DE10674 In VisualRF, a restart is no longer required to view overlays after importing a controller’s floor plan
backup.
DE10685 An Access Denied page no longer displays when attempting to view a rogue detail page from a Master
Console using the rogue client report.
DE10707 APs without management mode and whose group has config-audit disabled do not have maintenance
windows.
DE10731 On the Clients > Diagnostic page, graphs that contain no data now display with a “No Data Found”
message rather than as a empty gap in the page.
DE10744 Empty Channel Utilization and Noise graphs are now hidden in Client Diagnostics view. These graphs
will appear when data is available.
DE10751 The remove_duplicate_aps.pl script no longer deletes APs that have an empty Device Serial\Lan
MAC\Chassis ID setting. A new option, --delete_null_devices, was created to remove these APs.
DE10784 VisualRF: Users are no longer required to clear their browser cache after upgrading from previous
versions of AMP in order to see campuses in the proper location.
DE10798 SNMP community strings are now obfuscated in trap messages instead of being readable.
DE10801 Device override now persists after a VisualRF restart.
DE10810 AMP installations now clear any existing disk partition labels because pre-existing disk labels may
cause installations to fail.
DE10849 Fixed an issue in VisualRF that caused the AMP status header and the top-level navigation header to
display after resizing a floor plan.
DE10865 When a firmware job fails, links on the Firmware File column of the Firmware details page now points to
the correct location.
DE10889 On the controller Monitor page, monitor-only users can no longer view the system event log.
DE10922 Added a CAD Layout panel to the image upload wizard in VisualRF. This new panel includes a
checkbox that allows users to toggle on/off Active Layout in the dwgconvert command, which is
useful when displaying DWF files.
DE10936 Fixed an issue in which AMP failed to notify the user of a mismatch when a VLAN changed. This
occurred when an AP lost power or rebooted. The AP reported on the controller that the VLAN
associated with some SSID had changed, and the SSID is now associated with new VLAN. AMP did not
display this as mismatch. Instead, AMP showed the SSID with the new VLAN in the manage page
without doing any import on the AP or on the controller.
DE10950 AMP no longer allows users to create multiple templates for the same device type with Restrict to this
version set to No on both templates. In addition, a Template Firmware Version is required when
specifying Restrict to this version.
DE10956 The upgrade script no longer automatically overwrites a pre-upgrade backup. Instead, users who have
an existing pre-upgrade backup are prompted whether to overwrite pre-upgrade backup.
DE10964 If an Aruba controller is moved to a new group in AirWave, the Aruba controller AP Group for the
controller thin APs is no longer automatically changed as well.
DE10966 Increased the page load speed of the APs/Devices > Monitor pages by relocating audit logs to their
own page.
DE10972 For Cisco controllers that do not include support for remote WLANs (prior to firmware version 7.0.116),
AMP will not push a remote WLAN profile even though the remote WLAN profile is configured on AMP.
In addition, AMP ignores the remote WLAN profile while performing the device configuration audit.
DE11000 When a Device Down trigger is specified for a switch, the trigger no longer sends an alert each time an
AP on the switch goes down.
DE11011 The TX Power column on the Wireless Settings > Radios table now shows 0 dbm
instead of
<unknown> when the value of an AirMesh AP radio’s transmit power is 0.
DE11025 Clients with a signal quality of less than 1 are no longer tracked in the Client Signal Distribution chart.
DE11045 Fixed an issue to speed up the restarting of daemons.
Table 7 Resolved Issues in AirWave 7.5.0 (Continued)
ID Description