User guide

12 AirWave 7.5.6 | Release Notes
DE11050 Mesh/Overhead BW graph lines no longer display for APs that do not support radio bandwidth fetching.
DE11061 Fixed an issue that caused upgrading to fail with a ‘No Disk Space Left’ error even when the hardware
specs meet the recommendations. AMP now verifies the disk space before starting based on the size of
the largest existing database table or the estimated size to migrate a large round-robin database.
DE11075 The Rogues Contained table on the APs/Devices > Rogues Contained page can now be sorted by
the “Last Seen” date.
DE11080 The Threshold values available on the Clients > Diagnostics page no longer includes ‘Poor’ values.
Data that matches ‘Good’ or better falls in the Good category. Data that matches between ‘Good’ and
‘Fair’ fall in the ‘Fair’ category. Anything below ‘Fair’ is by default considered as ‘Poor.’
DE11095 The Aruba License Report now displays information for standalone Aruba master controllers.
DE11096 In VisualRF, the alert that displays for the AP Bandwidth now matches the information that displays in
the left-click popup.
DE11102 AirMesh users who lack write permissions now receive a warning message when they attempt to
upgrade firmware or push configuration changes.
DE11105 The timeout value for remote authentication in RADIUS, TACACS, and LDAP modes now defaults to 15
seconds. In the event that remote authentication fails, this ensures that the time it takes to log in to AMP
with local priority will take less than a minute. Note that this value is not configurable on the UI, but this
can be modified with the remote_auth_timeout setting in the seas_config table. Contact
technical support for more information.
DE11110 The Inventory Report now shows the correct bootloader and version summary information.
DE11119 Error logging for AirMesh firmware upgrades has been improved.
DE11120 AMP now treats ‘0’ as ‘empty’ when importing a 0 antenna gain from a device. Because the antenna
range is 1-255, a value of ‘0’ would result in a validation error.
DE11121 The Export CSV button has been removed from the System > Syslog & Traps page. This export can be
done from the Device Events page within the AP Monitoring and Client Monitoring pages.
DE11122 The “Use DHCP” option is now imported correctly for AirMesh gigabit interfaces.
DE11130 Resolved an issue for under Groups > Cisco WLC Config > Mobility Management, where changes
made to the Automatically create mobility group elements for <default mobility domain> setting in
the drop down menu were not being recognized.
DE11132 On AirMesh MSR APs, the AP Monitoring page now loads properly when users navigate there
immediately after editing an interface.
DE11139 The password in the AirMesh configuration template is now encrypted.
DE11140 When upgrading failover AMP, users with a default role of “Read-Only Monitoring & Auditing” are
deleted as is the role itself. This is because non-admin roles cannot be created on failover AMP.
DE11143 All AirMesh MSR2000 devices (PoE, AC, DC) now share the same template.
DE11161 When a device includes more than 1000 clients, the client count that displays in the associated Client
Count graph is no longer truncated. (For example, “1420” clients no longer displays as “1.4k” clients.)
DE11165 When you display a floor plan on the VisualRF tab and select the Display > Relations > APs option, the
relational lines between APs are no longer retained when you click the page refresh icon ( ) in the
upper right corner of the window.
DE11175 Fixed a VisualRF issue in which the direction of the breadcrumb arrows did not reset. This occurred
when locating a whose Host AP resided on another floor, and the user selected the Show Host AP
Floor Plan link. In addition, attempting to return to the previous floor resulted in an error.
DE11179 The upper limit for the SNMP Retries setting on the Device Setup > Communication page has
changed from 20 to 40. Note that some SNMP libraries still have a hard limit of 20 retries. In these
cases, any retry value that is set above 20 will still stop at 20.
DE11182 The TX Power value now displays correctly on the Manage page for AirMesh MSR4000 APs.
DE11192 The size of the visualrf_msg.log file no longer increases significantly when RTLS messages are included.
Table 7 Resolved Issues in AirWave 7.5.0 (Continued)
ID Description