User guide

AirWave 7.5.6 | Release Notes 19
DE11264 A VisualRF floor plan may occasionally show multiple device types with the same MAC address.
DE11309 In VisualRF, be sure to drag new building icons away from the very upper-left corner of the canvas.
Failing to do so can cause inconsistent right-click menus to display. Specifically, you may right-click on
the building and see options specific for the background/canvas rather than for the building. Note that
this does not occur if you move the building away from the upper-left corner.
DE11316 A limitation in Aruba Instant causes a VC to send duplicate payload information to the Events log.
DE11343 Reports do not currently run in parallel, but rather one at a time. As a result, if a report is being run that
takes a long time to generate, other reports may not run until that one is completed.
DE11562 In cases where ports are connected with IP phones, and PCs are connected into those IP phones,
AirWave can display an incorrect port mode on the switch interface. This is because AirWave detects
more than one MAC address communicating through the port and, as a result, marks it as a distributed
port even if it is configured as an Access port on the switch.
DE11594 Moving a large number of controllers from one group to another all at once can take a long period of
time or can sometimes fail. If you notice this behavior, we recommend that you reduce the size of your
bulk moves.
DE11604 Ignoring mismatches for a large number of controllers all at once can take a long period of time or can
sometimes fail. If you notice this behavior, we recommend that you reduce the size of the number of
configuration mismatches that you ignore all at once.
DE11705 If the Max-tx-power for an Instant device is configured to be Max (greater than 33), then the value that
displays may differ than the value that displays on the AMP audit page.
DE11718 IE 8/9 users may notice broken or missing pie chart images when selecting Print or Print Preview within
the browser. If you notice this behavior, one workaround is to add the AirWave IP as a “Trusted Site” in
IE. Another workaround is to select Override automatic cookie handling in Internet Options >
Privacy > Advanced and then refresh the page.
DE11740 Stacked switches only allow interface editing from the master/primary switch. Currently, information
within the audit log is populated based on the interface that is edited. So if a change is made on the
member switch interface, the member switch audit log is populated with the change. As a result, users
must navigate to that member switch in order to verify the audit log.
DE11754 When the radio mode on a Mesh AP changes from 802.11an 40MHz plus to 802.11ng 40MHz minus, on
a portion of the change is reflected on AMP.
DE11757 While logged in as a Helpdesk user, the User Info page provides options for viewing Alerts and Severe
Alerts even though Helpdesk users cannot view these alerts.
DE11773 The default value for the Session ACL option is “none” when configuring AP Profiles through the Device
Setup > Aruba Configuration page in AMP. The controller (Configuration > All profiles > AP > AP
System Profile) shows this default value as “ap-uplink-acl.”
DE11835 In some cases, importing older Cisco wireless LAN controller (5.0 or earlier) can result in mismatches for
options that do not exist. The root cause is still under investigation; however, these mismatches can be
ignored.
DE11838 Newly added devices do not show up in a Quick Search.
DE11851 In some cases, users may be unable to resolve rogue classification mismatches. This is because it is
not possible to fix a controller’s rogue classification setting by importing.
DE11889 When adding a region in VisualRF, be sure to specify a region type before drawing the region. An error
will occur if a type is not selected.
DE11897 When a user adds a Cisco or Alcatel-Lucent switch stack, updates sysLocation on the stack using the
CLI, and then imports settings, the primary switch updates successfully, but member switches do not.
A current workaround is to delete and then re-add the members of the switch stack.
DE11910 Importing from controllers that do not have licenses can result in mismatches that may not be resolved.
DE11945 A web error can occur if you press Restart AMP and the page refresh does not complete before the
web server restarts.
Table 12 Known Issues in AirWave 7.5.0 (Continued)
ID Description