User guide

AirWave 7.5.6 | Release Notes 7
Table 2 below lists resolved issues in AirWave 7.5.5:
DE12817 Attempting to open a Groups > Basic page by specifying “ap_group_id=” in the navigation bar no
longer results in a page error. Now, “ap_group_id=” and “id=” can be used interchangeably.
DE12818 Fixed an issue that caused disc utilization to peak when the To p Clie n ts B y To t al Tr a ff ic widget was
added to the Home > Overview page.
DE12881 Fixed a memory issue that was caused by AMP failing to ignore interfaces on ignored member
switches. The result was that duplicate interfaces were created during polling periods. Now, AMP
ignores interfaces on ignored member switches.
DE12895 Fixed an issue in which Rogues that were found, contained, and added as neighbors would then display
again as rogues during the next polling period.
DE12902,
DE12792
Fixed an issue that caused a config import to fail when a custom name existed for certificates on a
controller, and that name did not match the name of the certificate on the desired configuration. Now,
the custom file name will no longer result in a mismatch.
DE12903 Fixed an issue that resulted in a “Server communication error” message on pages that contain graphs.
This issue was only see in IE 8 browsers with the Do not save encrypted pages to disk setting
enabled. Now, AMP no longer caches HTTP headers for dynamic files if the browser is earlier than IE 9.
NOTE: It is not possible to provide a fix or workaround for this issue in IE 9. Microsoft recommends
turning off the “Do not save encrypted pages to disk” setting. Refer to support.microsoft.com/kb/
2549423.
DE12925 Fixed an issue that caused global AOS configurations to be converted to group-based configurations
after an upgrade. This occurred when the Use Global Aruba Configuration option on the AMP Setup
> General page was set to No before an upgrade and then set to Yes after the upgrade.
DE12931 RAP-3WN and RAP-3WNP devices are now labeled properly in AMP, and the way that these devices
display is now consistent with the controller. In addition, clients that are associated with RAP-3 devices
are now visible in AMP.
DE12945 On a VC’s Manage page, the Reboot button now indicates that the reboot applies to all APs in the
cluster and not just to the VC.
Table 2 Resolved Issues in AirWave 7.5.5
ID Description
DE11651 VisualRF now includes the option to configure external antenna orientation for the Aruba AP175 device.
DE12373 Added new MIB entries for S3500, version 7.1.4.0 build 34027:
 wlsxIfStateChangeTrap
 wlsxLicenseClientExpiry
 wlsxLicenseServerExpiry
 wlsxStackIfStateChangeTrap
 wlsxStackTopologyChangeTrap
DE12470 The Replace Hardware feature now allows you to replace Cisco devices with Aruba devices.
DE12489 Fixed an encoding issue that caused VisualRF to show an AP as “down” when the AP was in fact “up.”
DE12536 Fixed an issue that caused RAP whitelist changes to not be pushed if the thin APs happen to go down
on AMP and get stuck in the configuration import state.
DE12548 Updated kernel (kernel-2.6.18-308.11.1.el5). See the Security section of this document for more details.
DE12549 Updated kerenl (kernel-2.6.32-279.1.1.el6). See the Security section of this document for more details.
DE12566 When updating AP Groups from Modify Devices, the previous AP Group name now displays on the
confirmation page.
DE12569,
DE12580
Fixed an issue in which only a single Thin AP in a group was updated during an LWAPP AP Groups
update.
DE12499,
DE12593
In VisualRF, fixed an issue in which the DWG Convert process resulted in 100% CPU usage.
Table 1 Resolved Issues in AirWave 7.5.6 (Continued)
ID Description