User guide

8 AirWave 7.5.6 | Release Notes
Table 3 below lists resolved issues in AirWave 7.5.4:
DE12598 In VisualRF, fixed an issue that caused overlays (heat maps, speed, etc.) failed to display for Cisco
881W, 881GW, and 891W devices.
DE12621 Fixed an issue that resulted in an error when attempting to add Cisco AP Group a group configuration.
DE12622 Fixed an issue in which an existing local controller was discovered again after upgrading, resulting in a
duplicate record.
DE12623 Fixed an issue that caused an upgrade from 7.4.0 to 7.5.3 to fail. This occurred when AMP attempted to
rename a report and came across an AMPLink object.
DE12630 Fixed an Instant issue that caused configurations to be built with invalid IP addresses.
DE12667 Upgrading from 7.5.3 to 7.5.4 no longer fails with an RRD cache error.
DE12669 Fixed an issue that cause configuration pushes to fail when attempting to modify a read-only value.
DE12711 The Network-wide Client Inventory and Network-wide Client Session report definitions no longer
incorrectly include a Matching option.
DE12719,
DE12422,
DE12534
Fixed an issue that occasionally caused gaps and/or missing information in the Utilization and Goodput
graphs for an AP radio.
DE12723 Fixed an issue in which the Group display options from the master controller global group were not
inherited by the subscriber group on MAMP. In addition, the Select devices in this group link is no
longer visible for the remote Global group and the subscriber group.
DE12725 Fixed SNMPv3 polling issues that occurred when a Primary device would go down. When the
Secondary switch becomes the Primary, the switch role now indicates this properly, and this new
Primary can now be polled.
DE12766 Fixed an issue that caused a client-count discrepancy. The number of clients on the Groups > List page
now matches the number of clients on the Home > Overview page Clients chart. Note that when
synching these values, you may experience a 5- to 10-minute latency.
DE12781 In VisualRF, Dell PowerConnect W model access points now display correctly in the device catalog.
US8344 In Visual RF, Cisco 881W, 881GW, 891W, 1941W ISRs are no longer treated as APs, and Cisco SRE
Module for 1941 ISR is no longer treated as a WLC.
Table 3 Resolved Issues in AirWave 7.5.4
ID Description
DE12161 Fixed a error that occurred when two duplicate physical interfaces existed on the same switch. In this
scenario, one of the interfaces had the proper settings, and the other showed a mismatch.
DE12301 Fixed an issue in which AMP failed to retain “Channel,” “Noise,” “Power,” and “AC/Phy Error” data after
performing Replace Hardware.
DE12302 Fixed an inconsistent floor-plan-import issue in VisualRF. When importing a floor plan, exporting the
plan, and then reimporting, the second import was occasionally incomplete.
DE12347 Updated kernel (kernel-2.6.18-308.8.2.el5). See the Security section of this document for more details.
DE12355 Fixed a PCI 1.1 Compliance issue that occurred with IAP devices. For these devices, the Daily PCI
Compliance Report no longer result in a “Device is not configured by AMP or device configuration is
not audited by AMP yet” message. In addition, the details for the status no longer show an “Unable to
Determine” message.
DE12371 The e-mail output for custom reports no longer contain orphaned entries. This output now matches the
report that is generated in AMP.
DE12377 AirWave removes Machine Authentication users created by AOS with no role. Note that Machine
Authentication entries are CACHED entries created by AOS when a machine does a pre-user-auth
machine login to the controller. These users are not created manually or by an external service.
Table 2 Resolved Issues in AirWave 7.5.5 (Continued)
ID Description