W-ClearPass 500 Hardware Installation Guide
Contacting Support Website Supportain Website Main Website dell.com Support Website support.dell.com Dell Documentation support.dell.
Table of Contents Section 1 Safety Notice and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section 2 Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section 3 Electrical and General Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Section 4 Unpacking the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Safety Notice and Warnings FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. No Telecommunications Network Voltage (TNV)-connected PCBs shall be installed. This class A digital apparatus complies with Canadian ICES-003.
3. Electrical and General Safety Guidelines CAUTION This appliance is intended for installation in restricted areas only. Initial setup and maintenance should be performed by qualified personnel. CAUTION Power down the appliance following the operating system’s proper power down procedure from the front panel. Unplug all AC power cord(s) before servicing. CAUTION To avoid electrical shock, check the power cords as follows. This product is to be installed in Restricted Access Location only.
3. Electrical and General Safety Guidelines (continued) WARNING Disconnect the power supply at the circuit breaker before accessing any components. Turning off the system power supply switch does not reduce the risk of electrical shock from the power supply terminal block. CAUTION • To prevent the unit from overheating, never install the appliance in an enclosed area that is not properly ventilated or cooled.
4. Site Preparation Setup location, rack and appliance precautions • Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
5.
6A. 4-Post Rack Installation Unpack the appliance and locate the mounting hardware Step 1 • Remove the inner fixed chassis rails from the outer fixed chassis rails. • Pull each one out as far as possible. • Depress the locking tab to pull the inner rail completely out. • Put these rails aside for later installation on the appliance. Step 2 • Attach the long (A) and short (B) brackets to the outer fixed chassis rails as shown, using the shorter ones in the front and the longer ones in the rear.
6B. 2-Post Rack Installation Unpack the appliance and locate the mounting hardware Step 1 • Remove the inner fixed chassis rails from the outer fixed chassis rails. • Pull each one out as far as possible. • Depress the locking tab to pull the inner rail completely out. • Put these rails aside for later installation on the appliance. Step 2 • Attach the long fixed (A) and the small (B) brackets to the 2-post rack.
7. Rail Installation on the Appliance Locate the fixed chassis rails that were put aside in 6A or 6B, Step 1 on pages 8 or 9. • Mount the inner fixed chassis rails to each side of the appliance using three M4 x 4 truss head screws on the left and right sides as shown. 8. Installing the Appliance in the Rack • Align the inner fixed chassis rails on the appliance with the outer fixed chassis rails previously installed in the rack.
9. Rear Panel Connections • Step 1: Connect the power cord. CAUTION • Step 2: Connect the Ethernet cables. Slide rail/mounted equipment is not to be used as a shelf or a work space. • Step 3: Connect any other required cables. 10. Front Panel Operation Power on the appliance. The power button is the last button on the right side on the front of the appliance.
