Reference Guide Dell Networking W-Series Instant Access Point 6.2.1.0-3.
Copyright © 2013 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Contents Contents ................................................................................................... 3 Chapter 1 About the Guide ....................................................................................... 5 Document Organization.........................................................................................5 Format of Messages..............................................................................................5 Severity Levels ................................
Debug Messages.................................................................................................85 4 | Dell Networking W-Series Instant Access Point 6.2.1.0-3.
Chapter 1 About the Guide This document covers syslog messages included in this Dell W-Instant release. In this edition, message definition, recommended action and in some cases the cause that generated the syslog message are included. Syslog messages were prioritized for definition; this edition includes definitions for approximately 70% of Dell W-Instant syslog messages. For those messages yet to be defined, the phrase “No description available” appears.
These substitutions generate message text as follows: AM 00:0b:86:38:5d:b0: Interfering AP detected with SSID 06B408550367 and BSSID 00:12:0e:44:d4:2c In the following chapters, messages are defined in generic terms with variables shown to indicate where substitutions of actual data will occur. Severity Levels The severity levels defined for syslogs are outlined in Table 1, which orders the severity from most to least severe.
Syslog Server To specify a Syslog Server for sending syslog messages to the external servers, navigate to System > Show advanced options > Monitoring in the UI and update the following fields. Syslog server— Enter the IP address of the server to send system logs. Syslog level— For a global level configuration, select one of the logging levels from the standard list of syslog levels. The default value is Notice.
information kept in the system logs is important. The capabilities required for handling logs should include the following: Efficient log management Sophisticated analysis capabilities Consistent report generation Scalability Security Analyzing system logs, and extracting relevant information from them, requires an efficient pattern matching engine, where the desired patterns can be created with standard pattern matching commands, such as a regular expression engine.
Chapter 2 Security Messages Critical Messages Table 4 Security Critical Messages Message ID Message and Description 132002 Enabling dot1x termination for AP [mac:%m] [auth_profile:%s] before cert download. Description: Termination is being enabled before certificate is downloaded. 132011 Station [mac:%m] [name:%s] not found in AP’s [bssid:%m] station table. Description: Station is not found in the specified AP’s station table. 132014 “AP [bssid:%m] [apname:%s] Incomplete AP configuration.
Table 4 Security Critical Messages (Continued) Message ID Message and Description 132146 ssl_get_server_send_cert faileds Description: sl_get_server_send_cert failed Error Messages Table 5 Security Error Messages Message ID Message and Description 121000 Failed to calculate the HMAC-MD5 digest Description: Controller failed to calculate the HMAC-MD5 digest for RADIUS packet due to an internal error. Recommended Action: If the problem persists, contact Aruba support provider.
Table 5 Security Error Messages (Continued) Message ID Message and Description 121012 Not enough buffer space to verify RADIUS server response packet with length [totallen:%d]. Description: The internal buffer is not big enough for the RADIUS response packet and RADIUS secret. Recommended Action: Check the length of the RADIUS response packet from the RADIUS server and the length of RADIUS secret. 121013 Received non-matching ID in RADIUS server response [id:%d], expecting [seq_nbr:%d].
Table 5 Security Error Messages (Continued) Message ID Message and Description 121029 RADIUS: Error [errno:%d], [errstr:%s] creating rfc3576 socket. Description: Internal error occurred while initiating connection with RADIUS server. Recommended Action: If the problem persits, contact your support provider. 121030 RADIUS: Error [errno:%d], [errstr:%s] in rfc3576 bind. Description: Error occurred while connecting to RADIUS server.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132010 Station [mac:%m] [name:%s] not associated with AP [bssid:%m] Description: Station is not associated to the specified AP 132012 Station delete failed [name:%s] [mac:%m] [bssid:%m] Description: Failed to delete the specified station Recommended Action: Clear the station by running the aaa user delete command. and reconnect. Manually clear the station by running the aaa user delete command.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132025 Station [mac:%m] [bssid:%m] is not enabled for pre-auth. Description: Preauthentication is always disabled 132026 Station [mac:%m] [bssid:%m] trying to pre-authenticate with AP that does not have WPA2 enabled Description: Station trying to preauhenticate with AP that is not WPA2 enabled. Configure the ssid-profile to enable WPA2 and reload the AP.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132038 Station [mac:%m] [bssid:%m] sent Unsupported EAP type [eaptype:%d]]“ Description: Station sent an EAP packet that is not supported. Recommended Action: Ensure the station is configured correctly to perform an EAP authentication method that is supported by the controller. Ensure that the aa a-profile associated with the authentication request matches the authentication-method the client is sending to authenticate.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132055 “[__FUNCTION__:%s]: missing configuration for dot1x profile \””[prof:%s]\”” Description: Specified Dot1x profile is not configured or has been deleted. Recommended Action: Validate that the controller configuration contains the specified dot1x profile.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132073 Wrong WPA OUI Element [oui:%d] from Station [mac:%m] [bssid:%m] [apname:%s] Description: Station sent WPA key message with invalid OUI element. Recommended Action: Identify the station and investigate why it is sending incorrect data.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132084 Two TKIP Michael MIC Failures were detected within [last_scan_time:%d] seconds.AP will be shutdown for next 60 seconds Description: Two MIC failures was received from the station within 60 secs.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132147 Invalid length [ln:%d] during inner EAP handling Description: Station sent invalid length in the inner eap 132149 Station [mac:%m] [bssid:%m] lookup failed Description: Specified station failed lookup 132150 Station [mac:%m] [bssid:%m] does not have 802.1x context Description: Station [mac:%m] [bssid:%m] does not have 802.1x context 132152 “802.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132180 Station [mac:%m] [bssid:%m] sent Unknown SSL type in the client finish header [type:%d] Description: Station sent unknown SSL type in the client finish header 132182 Verify data sent by the Station [mac:%m] [bssid:%m] is not valid Description: Verify data sent by the specified station in not valid 132185 Failed to send the server finish for Station [mac:%m] [bssid:%m] Description: Failed to send server finish for th
Table 5 Security Error Messages (Continued) Message ID Message and Description 132207 RADIUS reject for station [name:%s] [mac:%m] from server [server:%s]. Description: Radius packet for the specified station was rejected by the server.
Warning Messages Table 6 Security Warning Messages Message ID Message and Description 106010 “AM [bssid:%s]: Containment enabled on Suspect Rogue AP: BSSID [ap_bssid_str:%s], SSID [ssid:%s], Conf-Level [conf_level:%d] “ Description: Containment has been enabled for a suspected rogue AP because the confidence level for that AP equals or exceeds the configured value for that setting 121004 RADIUS server [name:%s]-[fqdn:%s]-[ipaddr:%s]-[sin_port:%u] timeout for client=[cbuf:%s] auth method [server:%s].
Table 7 Security Notice Messages Message ID Message and Description 106012 AM: Wireless tarpit containment: Sending Probe-Response with fake channel from AP [bssid:%m] to STA [mac:%m] on channel [channel:%d] with fake_channel [fc:%d] Description: No description available. 106013 AM: Wireless tarpit containment: Sending Probe-Response with fake BSSID for frame from AP [bssid:%m] to STA [mac:%m] on channel [channel:%d] with fake_bssid [fbssid:%m] Description: No description available.
Table 8 Security Information Messages Message ID Message and Description 121035 RADIUS type not sent: [type:%s] Description: Controller has a reference to a RADIUS type that will be dropped.
Table 8 Security Information Messages Message ID Message and Description 132131 FIPS mode is enabled. Description: FIPS mode is enabled. 132132 FIPS mode is disabled Description: FIPS mode is disabled.
Table 9 Security Debug Messages Message ID Message and Description 121044 Radius authenticate user ([user:%s]) PAP query using server [server:%s]. Description: This shows an internal debug message 121045 [func:%s]: sta_update_last_srv_grp failed. Description: This shows an internal debug message 121046 [func:%s]: last_srv_grp [last_srv_grp:%s].
Chapter 3 System Messages Emergency Messages Table 10 System Emergency Messages Message ID Message and Description 330203 MESHD process initialization failed. Cause: MESHD process initialization failed possibly because the mesh-node is not correctly provisioned. Recommended Action: Re-provision the AP. Contact Dell technical support if this problem persists. 330204 MESHD process exiting. No MESH role was specified. Cause: No MESH role was specified. Recommended Action: Re-provision the AP.
Table 11 System Alert Messages (Continued) Message ID Message and Description 341285 Managed mode: Config file download retry count over. Description: Config file download retry count over. 341286 Could not download the required file, reason [reason:%s]. Description: Could not download the required file 341287 Managed mode: Could not apply the config fetched from server [reason:%s], error code [error_code:%d]. Description: Could not apply the configuration fetched from server.
Table 13 Error System Messages (Continued) Message ID Message and Description 304045 Connection to User DB failed Description: The application was not able to connect to the user database. 304046 Creation of Client Blacklist tables in User DB failed Description: The application was not able to create the Client Blacklist tables in the user database. 304047 SQL Command [command:%s] failed on User DB.
Table 13 Error System Messages (Continued) Message ID Message and Description 311016 Unable to create domain list file Description: Internal error occured while accessing domain lists file.
Table 13 Error System Messages (Continued) Message ID Message and Description 326071 AM: System encountered an internal communication error. Error occurred when message was sent from source application [src:%s] destination application [dst:%s] at file [file:%s] function [func:%s] line [line:%d] error [error:%s]. Description: This log indicates that application processes in the system encountered an error when sending messages to each other.
Table 13 Error System Messages (Continued) Message ID Message and Description 330209 An internal system error has occurred at file [file:%s] function [function:%s] line [line:%d]. Description: This log indicates that we encountered an internal system error. Recommended Action: Contact your support provider 330210 An internal system error has occurred at file [file:%s] function [function:%s] line [line:%d] error [error:%s]. Description: This log indicates that we encountered an internal system error.
Table 13 Error System Messages (Continued) Message ID Message and Description 341036 [func:%s]: invalid image name. Description: The AP is upgrading image. 341037 Open image-[image:%s] fail. Description: The AP is upgrading image. 341038 Read image-[image:%s] header fail. Description: The AP is upgrading image. 341039 AP check image-[image:%s] version fail. Description: The AP is upgrading image. 341040 AP verify image-[image:%s] fail. Description: The AP is upgrading image.
Table 13 Error System Messages (Continued) Message ID Message and Description 341063 Could not open socket for [dip:%x]/[mask:%x]. Description: The AP is setting kernal route. 341064 Could not add route for [dip:%x]/[mask:%x]. Description: The AP is setting kernal route. 341067 Open socket for corp fail [dip:%x]/[sip:%x]/[devname:%s]. Description: The AP is creating tunnel. 341068 Get ifindex for corp fail [dip:%x]/[sip:%x]/[devname:%s]. Description: The AP is creating tunnel.
Table 13 Error System Messages (Continued) Message ID Message and Description 341108 [func:%s]: [line:%d] invalid session client-[ip:%s] sid-[sid:%s]. 341109 [func:%s]: save certificate fail-[error:%s]. Description: AP is setting cert. 341110 [func:%s]: delete certificate fail-[error:%s]. Description: AP is setting cert. 341111 [func:%s]: save cert key fail-[error:%s]. Description: AP is setting cert. 341113 [func:%s]: get gre host fail by [server:%s]. Description: AP is setting gre name.
Table 13 Error System Messages (Continued) Message ID Message and Description 341211 [func:%s]: ASAP to CLI socket ioctl failed [fd:%d] [errno:%d]. Description: ASAP to CLI socket ioctl failed. 341212 [func:%s]: ASAP to CLI socket bind failed [fd:%d] [errno:%d]. Description: ASAP to CLI socket bind failed. 341213 [func:%s]: ASAP to CLI socket recv failed [fd:%d] [errno:%d]. Description: ASAP to CLI socket recv failed. 341214 [func:%s]: L2 Roam failed at home network [mac:%s] [ssid:%s].
Table 14 Warning System Messages (Continued) Message ID Message and Description 304009 enet_move_tunnel: Tunnel [id:%d] not found Description: No description available. 304011 stop_signal - Why was I called ... exiting Description: No description available. 304013 tunnel_timeout: Tunnel 0x[tunnel_id:%x] not found Description: No description available. 304014 received frame of unknown type [type:%x] (subtype [stype:%x]) Description: No description available.
Table 14 Warning System Messages (Continued) Message ID Message and Description 304033 Mesh AP support not licensed; dropping request Description: No description available. 304044 Waiting for dbstart... Description: The application is waiting for the database to be ready for access. 304048 User DB query issue in: [call: %s]. SQL command: [cmd: %s]. Description: This log indicates that there was an issue when a command was executed on the user database.
Table 14 Warning System Messages (Continued) Message ID Message and Description 326084 AM: Setting the communication path of state and stats info to: Local switch Description: No description available. 326085 AM: Setting collection of statistics to : [mode:%s] Description: No description available. 326096 AM: message too long [bl:%d] Description: No description available. 326157 AM: Too many Wi-Fi(s) interfaces = [wifi_index:%d] Description: No description available.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341102 Incorrect format for message type[type:%d]:[msg_len:%d]:[recv_len:%d]:[bytes_read:%d]:[from_ip:%s]:[from_port:% d]. Description: Handle papi message. 341103 Unknown version from [ipaddr:%s] in message type-[type:%d]. Description: Handle papi message. 341104 Invalid version for message type-[type:%d] from [ipaddr:%s] (local [ver:%s] vs. master [m_ver:%s]). Description: Handle papi message.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341177 Try next uplink because current uplink is down - [type:%s]. Description: Try next uplink. 341181 Setup ip for uplink - [type:%s]. Description: Setup ip for uplink interface. 341182 Setup vpn for rap conversion - [ip:%s]. Description: Setup vpn for rap conversion. 341183 Downloading rap image via vpn - url [url:%s]. Description: Downloading rap image via vpn.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341250 VC record delta configuration, malloc error. len [len:%d] port [port:%d] flags [flags:%d] seq [seq:%d] case [case:%s] Description: VC record delta configuration, malloc error. 341252 VC send delta configurations to ap error. ap [ap_ip:%s] ap_cfg_id [acid:%d] current_cfg_id [cid:%d] top_cfg_id [tid:%d] case [case:%s]. Description: VC send delta configuration to ap error.
Notice Messages Table 15 Notice System Messages Message ID Message and Description 304006 IGMP Drop Tx - [s_addr:%p] Description: No description available. 304007 IGMP Join Tx - [s_addr:%p] Description: No description available. 304031 PAPI message to [ip:%p] port [port:%d] timed out Description: No description available.
Table 15 Notice System Messages (Continued) Message ID Message and Description 326101 AM: length mismatch for message [msg_type:%d], expected [bytes_read:%d], got [msg_len:%d]. Description: No description available. 326102 AM: unable to find AP [bssid:%s]. Description: No description available. 326106 AM: unable to find STA [bssid:%s] PHY [phy_type:%d]. Description: No description available. 326107 AM: RSTA Type set to [rap_type:%d] for STA [bssid:%s] Description: No description available.
Table 15 Notice System Messages (Continued) Message ID Message and Description 326276 AM: Inactive AP Detected SSID = [ssid:%s] BSSID = [bssid_str:%s]. Description: No description available. 326277 AM: Setting RAP Type for AP [bssid_str:%s] to: [rap_str:%s]. Description: No description available. 326278 AM: STA [mac_addr:%s] Authenticated with AP [bssid_str:%s]. Description: No description available. 341003 [msg:%s Description: No description available.
Table 15 Notice System Messages (Continued) Message ID Message and Description 341156 Sending image err [state:%s] to [ap_ip:%s]. Description: Send image err state to Master. 341157 AP reaches count [count:%d]-[msg:%s]. Description: AP image upgrade timeout. 341158 [func:%s],[line:%d]: Setup image with code [ret:%d]. Description: AP image upgrade timeout. 341201 AP [name:%s] reports a spectrum alert: non-wifi device(ID: [id:%d],type: [type:%s]). Description: Non-wifi device is detected.
Table 16 Information System Messages (Continued) Message ID Message and Description 326075 AM: Dropping PROBE_POLL_REQUEST from Switch IP [wms_ip:%s] Description: No description available. 326088 AM: Marking Switch [ip:%s] as Down Description: No description available. 326097 AM [bssid:%s]: Received a PROBE_POLL_REQUEST from [ip:%s] Description: No description available. 326098 AM: PAPI_Send failed.
Table 16 Information System Messages (Continued) Message ID Message and Description 341017 AP is adding auth server-[ipaddr:%s], as_port-[as_port:%d], acctport-[acctport:%d]. Description: The AP is configuring auth server. 341018 Auth server NAS ip-[ipaddr:%s]. Description: The AP is configuring auth server. 341019 Auth server source ip-[ipaddr:%s]. Description: The AP is configuring auth server. 341020 Add termination server-[ipaddr:%s]. Description: The AP is configuring termination server.
Table 16 Information System Messages (Continued) Message ID Message and Description 341078 AP remove acl-[name:%s]. Description: The AP is configuring ACL. 341079 AP flush acl-[name:%s]. Description: The AP is configuring ACL. 341080 [func:%s]: can't find acl-[name:%s]. Description: The AP is configuring ACL. 341084 Reset index of access rule profile [file:%s] from [old_id:%u] to [id:%u]. Description: The AP is configuring ACL.
Table 16 Information System Messages (Continued) Message ID Message and Description 341121 SNMP return [mac:%s]:[num:%d]. Description: SNMP action. 341128 [func:%s], [line:%d]: index-[idx:%d] is [type:%s]. Description: AP is setting SSID. 341129 [func:%s], [line:%d]: index-[idx:%d] of ssid-[ssid:%s]is set to [new_idx:%d]. Description: AP is setting SSID. 341134 AP will remove alerts of client-[mac:%s]. Description: AP is removing alerts.
Table 16 Information System Messages (Continued) Message ID Message and Description 341187 Add [mac:%m] to ap whitelist. Description: Add an ap to the whitelist. 341188 Del [mac:%m] from ap whitelist. Description: Del an ap from the whitelist. 341189 [func:%s]: discover client [mac:%s] [fapip:%s] [vlan:%d]. Description: Discover client request. 341190 [func:%s]: found client [mac:%s] [vlan:%d] [hapip:%s] [oldapip:%s] [vcip:%s]. Description: Found client response.
Table 16 Information System Messages (Continued) Message ID Message and Description 341218 [func:%s]: awc login to [ip:%s] successfully. Description: Awc login successfully. 341219 [func:%s]: awc identify [ip:%s] successfully. Description: Awc identify successfully. 341220 [func:%s]: L2 Roam session requested for client [mac:%s] [ssid:%s]. Description: L2 Roam session requested. 341221 [func:%s]: Foreign sta info for [mac:%s] from [vcip:%s]. Description: Foreign sta info.
Table 17 Debug System Messages (Continued) Message ID Message and Description 304051 In-memory client blacklist table cleared. Description: This log indicates that the in-memory client blacklist was cleared. 304052 Client blacklist database table cleared. Description: This log indicates that the client blacklist database table was cleared. 304053 Client blacklist repopulated from database. Description: This log indicates that the in-memory client blacklist was repopulated from the database.
Table 17 Debug System Messages (Continued) Message ID Message and Description 326095 AM:SM: Sending Spectrum Unregister Message for radio [r:%d] band [band:%s] to [ip:%s] Description: This log indicates that spectrum radio is un-registering with the controller. 326099 AM:SM: Received Spectrum Unknown Radio Message for [bssid:%s] Description: No description available. 326213 AM: MAC [mac:%s] matched with offset [match:%s] Description: No description available.
Table 17 Debug System Messages (Continued) Message ID Message and Description 341142 [func:%s], [line:%d]: html msg is [msg:%s]. Description: AP receives HTML message from controller. 341200 Check session id fail: client_ip [ip:%s], string [sid:%s]. Description: Checking session id fail 341234 Receive stats publish from [ip:%s]. Description: Receive stats publish msg. 341236 Add [mac:%s] [status:%s] to subscription ap list.
Table 17 Debug System Messages (Continued) Message ID Message and Description 341251 VC record new delta configuration entry. cfg_id [cid:%d] current [c:%d] top [t:%d] len [len:%d] port [port:%d] flags [flags:%d] seq [seq:%d]. Description: VC record new delta configuration entry. 341253 VC send delta configurations to ap. ap [ap_ip:%s] ap_cfg_id [acid:%d] delta_cfg_id [did:%d] current_cfg_id [cid:%d] top_cfg_id [tid:%d]. Description: VC send delta configuration to ap.
Chapter 4 User Messages Error Messages Table 18 User Error Messages Message ID Message and Description 524005 Invalid action :[file:%s],[func:%s],[line:%d],[action:%d] Description: This shows internal debug messages. 524006 [file:%s], [func:%s],[line:%d],cur=0x[cur:%x],end=0x[end:%x] Description: This shows internal debug messages. 524007 [file:%s], [func:%s],[line:%d], realloc size invalid, tot=:[tot:%d],certlen=:[len:%d] Description: This shows internal debug messages.
Table 18 User Error Messages 58 | User Messages Message ID Message and Description 524027 Error decoding MPPE send-key (code = [code:%d]) Description: This shows internal debug messages. 524028 Invalid MPPE send-key length:[len:%d] Description: This shows internal debug messages. 524030 Invalid Radius Code [radcode:%d] Description: This shows internal debug messages. 524043 [string:%s]: FT mic=[string1:%s] Description: This shows internal debug messages.
Table 18 User Error Messages Message ID Message and Description 524068 AES-GCM key setting is allowed only for Tunnel mode VAP's Description: This shows internal debug messages. 541012 [func:%s]: [line:%d]: find client-[mac:%m] fail. Description: Station sync. 541017 [func:%s]: parse tlv ret-[ret:%d] mac-[mac:%m] fail. Description: Station sync. 541018 [func:%s],[line:%d]: could not find client-[mac:%m]. Description: AP is looking up station.
Table 19 User Warning Messages 60 | User Messages Message ID Message and Description 501062 Station [sta:%m]: Ignored ATIM to BSSID [bss:%m] on AP [name:%s] Description: No description available. 501064 Station [sta:%m]: Ignored unknown management frame subtype [stype:%x]h to BSSID [bss:%m] on AP [name:%s] Description: No description available. 501067 Source: [sa:%m] Failed AP [ip:%p]-[bssid:%m]-[name:%s] Rates Mismatch STA 0x[rates:%x] AP 0x[tx_rates:%x] Description: No description available.
Table 19 User Warning Messages Message ID Message and Description 501086 Probe request: [mac:%m]: Invalid Station MAC address from AP [ip:%P]-[bssid:%m][name:%s] SSID [essid:%s] Description: No description available. 501091 Auth request: [mac:%m]: Invalid Station MAC address from AP [ip:%P]-[bssid:%m][name:%s] Description: No description available. 501092 Auth request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for STA DoS protection Description: No description available.
Table 19 User Warning Messages Message ID Message and Description 501124 Addts req: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] refused. Voice Capacities Reached Description: No description available. 501125 Addts req: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] refused. Flow Setup Failed Description: No description available. 501127 Delts: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] STA Not found Description: No description available.
Table 20 User Notice Messages Message ID Message and Description 501002 “Station [sta:%m]: ESSID length error trying to associate to BSSID [bss:%m] on AP [name:%s], length [len:%d] Description: No description available. 501003 “Station [sta:%m]: Supported rates length trying to associate to BSSID [bss:%m] on AP [name:%s], length [len:%d], actual [alen:%d] Description: No description available.
Table 20 User Notice Messages 64 | User Messages Message ID Message and Description 501087 Probe request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for STA DoS protection SSID [essid:%s] Description: No description available. 501088 Probe request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for Rates Mismatch STA 0x[rates:%x] AP 0x[tx_rates:%x] SSID [essid:%s] Description: No description available.
Table 20 User Notice Messages Message ID Message and Description 501110 Auth failure: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] Reason [resp:%d] Description: No description available. 501111 Deauth to sta: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] Reason [resp:%d] Description: No description available.
Table 20 User Notice Messages Message ID Message and Description 501167 [func:%s][line:%d]: mac-[mac:%m], role-[role:%s], caleaOn-[on:%d]. Description: This log indicates that a user has been caleaOn Information Messages Table 21 User Information Messages 66 | User Messages Message ID Message and Description 501035 Station [sta:%m]: DA [da:%m] not found trying to disassociate to BSSID [bss:%m] on AP [name:%s] Description: No description available.
Table 21 User Information Messages Message ID Message and Description 541049 Receive move req for sta-[mac:%m], essid-[essid:%s], from-[ap:%s] Description: Send station move request. 541050 Send move response for sta-[mac:%m], to ap-[ip:%s], Description: Send sta move resp. 541051 Recv sta move resp for sta-[mac:%m], from [ip:%s], Description: Receive sta move resp. 541052 Sta [mac:%s] move timeout, retry cnt [retry:%d] Description: Station move timeout.
Table 22 User Debug Messages 68 | User Messages Message ID Message and Description 501142 Derive user vlan: [mac:%m] Derive user Vlan [vlan:%d] from [reason:%s] Description: This log indicates that user vlan derivation information . 501143 Derive user vlan: [mac:%m] Can't derive user Vlan from [vlan1:%d] to [vlan2:%d] through [reason:%s] Description: This log indicates that user vlan derivation error information .
Table 22 User Debug Messages Message ID Message and Description 501162 Update dhcp-opt: [mac:%m] Update dhcp-opt [vlan:%d] [vlanhow:%s] [role:%d] rule_index [index:%x] essid [essid:%s] to cli0 msg. Description: This log indicates that update user dhcp-opt information to CLI. 501163 Send user role info: mac-[mac:%m], acl-[acl:%d]. Description: No description available. 501164 Receive disconnect user, mac-[mac:%m], bssid-[bssid:%m], logout-[logout:%d], deauth-[deauth:%d], term-[trem:%d].
Table 22 User Debug Messages 70 | User Messages Message ID Message and Description 524013 Forwarding the Radius packet after stateful dot1x processing code=:[code:%d], smac=:[smac:%s],sport=:[sport:%d],dport[dport:%d] Description: This shows an internal user debug message 524014 radius request timeout, unauthenticating station name:[name:%s], mac=:[mac:%s] Description: This shows an internal user debug message 524015 Forwarding the Radius Response to AP:[ipstr:%s],[len:%d] Description: This shows a
Table 22 User Debug Messages Message ID Message and Description 524041 [string:%s] :FT mesg3 copied gtk, len=[len:%d] data len=[len1:%d] Description: This shows an internal user debug message 524042 [string:%s]: FT mic=[string1:%s] Description: This shows an internal user debug message 524045 FT ([func:%s]): sap=[bssid:%s] mdie=[mdie:%d] ft_cap=0x[cap:%x] ucast=0x[ucast:%x] mcast 0x[mcast:%x] Description: This shows an internal user debug message 524047 USERNAME Description: This shows an internal
Table 22 User Debug Messages 72 | User Messages Message ID Message and Description 524076 FT ([str:%s]): anonce=[str1:%s] Description: This shows an internal user debug message 524077 FT ([str:%s]): Derived ptk [ptk:%s] Description: This shows an internal user debug message 524078 FT ([str:%s]): Derived ptk_name [ptk:%s] Description: This shows an internal user debug message 524079 FT ([str:%s]): essid:[essid:%s], bssid:[bssid:%s] ukey:0[ukey:%x], mkey:[mkey:%x], psk:[psk:%s],tkip:[tkip:%s] Descr
Table 22 User Debug Messages Message ID Message and Description 524095 Missing kcachThis shows an internal user debug message e entry! Description: 524096 PMKR0-Name mismatch! cached=[str:%s] Description: This shows an internal user debug message 524097 Generated anonce:[str:%s] Description: This shows an internal user debug message 524098 [str:%s]: Derived gtk=[str1:%s] Description: This shows an internal user debug message 524099 [str:%s]: Encrypted gtk=[str1:%s] Description: This shows an inte
Table 22 User Debug Messages 74 | User Messages Message ID Message and Description 524114 MAC auth failed, skipping dot1x. Description: This shows an internal user debug message 524115 Auth done called from Authenticated state. Description: This shows an internal user debug message 524116 DHCP UDR defined vlan. Got response from STM VLAN UPDATED. Description: This shows an internal user debug message 524117 Auth done called from Key Challenge.
Table 22 User Debug Messages Message ID Message and Description 541011 [func:%s]: sta look up req to apip-[ap_ip:%s], mac-[mac:%m]. Description: AP sent/receive station request. 541014 [func:%s]: sta lkup response to apip-[ap_ip:%s], mac-[mac:%m]. Description: AP sent/receive station response. 541015 [func:%s]: Add mac auth token for sta-[sta:%m]. Description: Station update. 541016 [func:%s]: add reauth ctx for client-[mac:%m]. Description: Station update.
Table 22 User Debug Messages 76 | User Messages Message ID Message and Description 541039 [func:%s]: Set dhcp-opt, Station [mac:%m] essid [essid:%s] role [num:%d] rule_index [index:%x] vlan [vlan:%d] vlanhow[vlanhow:%s]. Description: Station dhcp-option update. 541040 [func:%s]: Set os string, client [mac:%m], os [os:%s]. Description: Station os update. 541041 [func:%s]: update vc for client [mac:%m]. Description: Station update to vc.
Table 22 User Debug Messages Message ID Message and Description 541062 [func:%s]: Send accounting request, client mac-[mac:%m], status-[status:%u]. Description: Send sta accouting request to STM. Dell Networking W-Series Instant Access Point 6.2.1.0-3.
| User Messages Dell Networking W-Series Instant Access Point 6.2.1.0-3.
Chapter 5 Wireless Messages Error Messages Table 23 Wireless Error Messages Message ID Message and Description 400143 AP [name:%s]: ESSID mismatch index [ndx:%d]. expected [e1:%s] got [e2:%s] Description: An internal error has occurred. Recommended Action: Contact your support provider. 400144 AP [name:%s]: Station [sta:%m] not found while clearing association Description: An internal error has occurred. Recommended Action: Contact Aruba Technical Support.
Table 24 Wireless Warning Messages Message ID Message and Description 400169 “AP - [bssid:%m], max_clients [max_clients:%d] too big Description: No description available. 400171 wifi_sap_down:unknown SAP IP [ip:%P] BSS [bssid:%m] Description: No description available. 400172 wifi_load_balance:unknown SAP IP [ip:%P] BSS [bssid:%m] Description: No description available. 400173 wifi_update_sta_vlan: AP [bssid:%m] not found Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404050 AM [bssid:%s]: ARM C [channel:%d] PER [per:%d] MER [mer:%d] FRR [frr:%d] [arm_error_rate_threshold:%d]-[arm_error_rate_wait_time:%d] Description: No description available. 404052 AM [bssid:%s]: [message:%s] Description: No description available. 404061 AM [bssid:%s]: ARM Band Request - GC [g_covered_channels:%d] AC [a_covered_channels:%d] Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404072 AM [bssid:%s]: ARM - too much power decreasing... cov-index [arm_ci:%d]/ [arm_nci:%d] tx-power [current_tx_power:%d] new_rra [current_channel:%d]/ [arm_max_tx_power:%d] Description: No description available. 404073 AM [bssid:%s]: ARM - too little power increasing... cov-index [arm_ci:%d]/[arm_nci:%d] tx-power [current_tx_power:%d] new_rra [current_channel:%d]/ [arm_min_tx_power:%d] Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404092 AM [bssid:%s]: ARM HT Channel Band Trigger new [channel:%d]-[sec_channel:%d][arm_ii_arm_ccii:%d]/[arm_nii_arm_nccii:%d] old [ap_amc_channel:%d][ap_amc_channel_sec:%d]-[arm_ccii_arm_ii:%d]/[arm_nccii_arm_nii:%d] new_rra [min_amc_channel_pri:%d]-[min_amc_channel_sec:%d]/[new_tx_power:%d] Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404406 AM [bssid:%s]:SM: Unexpected channel [channel:%d] change by AM for Spectrum Monitor radio Description: No description available. Notice Messages Table 25 Wireless Notice Message Message ID Message and Description 400102 AP [name:%s]: probe request: dropped entry in ip table for [ip:%P] Description: No description available. 400160 AP [name:%s]: Starting to configure AP at [ap:%p] Description: No description available.
Table 25 Wireless Notice Message Message ID Message and Description 404400 AM:SM: Spectrum: new Wi-Fi device found = [addr:%s] SSID = [ssid:%s] BSSID [bssid_str:%s] DEVICE ID [did:%d] Description: This log indicates a new Wi-Fi device is detected by the spectrum radio. 404401 AM:SM: Spectrum: deleting Wi-Fi device = [addr:%s] SSID = [ssid:%s] BSSID [bssid_str:%s] DEVICE ID [did:%d]. Description: This log indicates a previously detected Wi-Fi device is being deleted due to inactivity.
Table 27 Wireless Debug Messages Message ID Message and Description 400133 “AP [name:%s]: SAPCP Probe from unknown bssid [bss:%m], dropping Description: No description available. 400134 AP [name:%s]: SAPCP: Unknown sap Description: No description available. 400162 “AP [name:%s]: Registering AP, new virtual ap for ESSID [ess:%s], deny broadcast [db:%d] Description: No description available. 400166 [msg:%s] Description: No description available.
