Dell™ PowerEdge™ 1950 시스템 하드웨어 소유자 설명서 w w w. d e l l . c o m | s u p p o r t . d e l l .
주 , 주의사항 및 주의 주 : 주는 컴퓨터를 보다 효율적으로 사용할 수 있도록 중요 정보를 제공합니다 . 주의사항 : 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며 , 이러한 문제를 방지할 수 있는 방 법을 알려줍니다 . 주의 : 주의는 위험한 상황 , 심각한 부상 또는 사망할 우려가 있음을 알려줍니다 . ____________________ 본 설명서에 수록된 정보는 사전 통보 없이 변경될 수 있습니다 . © 2009 Dell Inc. 저작권 본사 소유 . Dell Inc. 의 서면 승인 없이 어떠한 경우에도 무단 복제하는 것을 엄격히 금합니다 . 본 설명서에 사용된 상표 : Dell, DELL 로고 , Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, Dell OpenManage 및 Dell XPS 는 Dell Inc. 의 상표입니다 .
목차 1 시스템 정보 기타 필요한 정보 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 시작하는 동안 시스템 기능에 액세스 전면 패널 기능 및 표시등 . . . . . . . . . . . . . . . . . . . . 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 하드 드라이브 표시등 코드. . . . . . . . . . . . . . . . . . . . . . . . 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 전원 표시등 코드 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
시스템 암호 사용 설치 암호 사용 . . 잊은 암호 비활성화 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BMC(Baseboard Management Controller) 구성 BMC 설치 모듈 시작 . BMC 설치 모듈 옵션 . 3 . . . . . . . . . . . . . . . . 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . 시스템 구성요소 설치 권장된 도구 . . . . . . . . . . . . . . . . . . .
확장 카드 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 확장 카드 설치 확장 카드 분리 . 부팅 장치 구성 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 부팅 드라이브 구성 . System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 일반 메모리 모듈 설치 지침 최적이 아닌 메모리 구성 . .
후면판 보드 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 후면판 보드 분리 후면판 보드 설치 측면판 보드 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 측면판 보드 분리 측면판 보드 설치 시스템 전지 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 87 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 시스템 전지 교체 . . . . . . . . . . . . .
시스템 냉각 문제 해결 팬 문제 해결 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 시스템 메모리 문제 해결 . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 광학 드라이브 문제 해결 . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 하드 드라이브 문제 해결 . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 SAS 또는 SAS RAID 컨트롤러 보조 카드 문제 해결 확장 카드 문제 해결 . . . . . . . . . . . . 107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 도움말 얻기 기술 지원 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 온라인 서비스 . . . . . AutoTech 서비스 . . . . 자동 주문 현황 서비스 기술 지원 서비스 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dell Enterprise Training and Certification . 129 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 . . . . . . . . . . . . . . . . .
시스템 정보 본 절에서는 컴퓨터의 필수적인 기능을 제공하고 보장하는 물리적 , 펌웨어 및 소프트웨어 인터 페이스 기능에 대해 설명합니다 . 해당 시스템의 전면 및 후면 패널에 있는 물리적 커넥터는 편 리한 연결성 및 시스템 확장 기능을 제공합니다 . 시스템 펌웨어 , 응용프로그램 및 운영 체제는 시스템 및 구성요소의 상태를 모니터링하고 문제가 발생한 경우에 경고합니다 . 시스템 상태는 다음과 같은 방법으로 보고될 수 있습니다 . • 전면 또는 후면 패널 표시등 • LCD 상태 메시지 • 시스템 메시지 • 경고 메시지 • 진단 메시지 • 경고 메시지 본 절에서는 각 유형의 메시지를 설명하고 발생 가능한 원인을 나열하며 메시지에 의해 표시되 는 모든 문제를 해결하는 절차를 제공합니다 . 시스템 표시등 및 기능에 대한 설명이 본 절의 그 림에 나와있습니다 . 기타 필요한 정보 주의 : 제품 정보 안내는 중요 안전 지침 및 규정사항에 대한 내용을 제공합니다 .
주 : 업데이트는 종종 기타 설명서의 내용을 갱신하므로 항상 support.dell.com 에서 업데이트를 확인 하고 우선적으로 읽으십시오 . • 릴리즈 노트나 읽어보기 파일에는 시스템에 대한 최신 업데이트 사항이나 전문가 또는 기술자를 위한 고급 기술 참조 자료가 포함되어 있기도 합니다 . 시작하는 동안 시스템 기능에 액세스 표 1-1 은 시작하는 동안 시스템 기능에 액세스하기 위해 입력해야 하는 키입력을 설명합니다 . 키입 력를 입력하여 부팅을 완료하기 전에 운영 체제가 로드되기 시작하면 시스템을 재시작하고 다시 해 보십시오 . 표 1-1. 시스템 기능에 액세스하는 데 사용되는 키입력 키입력 설명 시스템 설치 프로그램을 시작합니다 . 33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시 오. 시스템 진단 프로그램을 시작합니다 . 114 페이지 " 시스템 진단 프로그램 실행 " 을 참조하십시 오.
전면 패널 기능 및 표시등 그림 1-1 은 시스템 전면 패널에 있는 랙 베젤 옵션 뒷부분의 제어부 , 표시등과 커넥터를 보여줍니다 . 그림 1-1. 1 전면 패널 기능 및 표시등 2 3 4 5 6 8 7 표 1-2. 전면 패널 LED 표시등 , 단추 , 커넥터 항목 표시등 , 단추 또는 커넥터 아이콘 설명 1 전원 켜짐 표시등 , 전원 단추 전원 단추는 시스템으로의 DC 전원 공급 장치의 출력 을 제어합니다 . 주 : ACPI 준수 운영 체제를 사용하는 경우에는 전원 단 추를 사용하여 시스템을 끄면 전원이 꺼지기 전에 정 상적으로 천천히 종료됩니다 . ACPI 준수 운영 체제를 사용하지 않는 경우에는 전원 단추를 누르면 즉시 전 원이 꺼집니다 . 2 NMI 단추 특정 운영 체제 사용하는 경우의 소프트웨어 및 장치 드라이버 오류 문제를 해결합니다 . 이 단추는 용지 클 립 끝 부분을 사용하여 누를 수 있습니다 .
표 1-2. 전면 패널 LED 표시등 , 단추 , 커넥터 ( 계속 ) 항목 표시등 , 단추 또는 커넥터 4 LCD 디스플레이 아이콘 설명 시스템 ID, 상태 정보 및 시스템 오류 메시지를 표시합 니다 . 시스템이 정상적으로 작동되는 동안 LCD 디스플레이 가 표시됩니다 . 시스템 관리 소프트웨어 및 시스템의 전면과 후면에 있는 확인 단추는 특정 시스템을 식별 할 때 LCD 가 청색으로 깜박이게 합니다 . 시스템의 전원 공급 장치 , 팬 , 시스템 온도 또는 하드 드라이브에 문제가 발생한 경우 , LCD 디스플레이가 호박색으로 바뀝니다 . 주 : AC 전원에 연결된 시스템에 오류가 발생했음을 감 지하면 시스템을 전원에 연결했는지 여부에 관계 없이 LCD 디스플레이가 호박색으로 켜집니다 . 5 USB 커넥터 (2 개 ) USB 2.0 호환 장치를 시스템에 연결합니다 . 6 비디오 커넥터 모니터를 시스템에 연결합니다 . 7 하드 드라이브 ( 선택 사양 ) 4 개의 2.
그림 1-2. 하드 드라이브 표시등 1 2 1 드라이브 상태 표시등 ( 녹색 2 과 황색 ) 녹색 드라이브 작동 표시등 표 1-3 은 드라이브 표시등 패턴을 나열합니다 . 시스템에서 발생하는 드라이브 이벤트에 따라 다른 패턴이 나타납니다 . 예를 들어 , 하드 드라이브 오류가 발생한 경우 , " 드라이브 오류 상태 " 패턴이 나타납니다 . 드라이브 분리를 선택한 경우에는 " 드라이브 분리 준비 상태 " 패턴에 이어 " 드라이브 설치 또는 분리 대기 상태 " 패턴이 나타납니다 . 교체용 드라이브를 설치하면 " 드라이브 작동 준비 상태 " 패턴에 이어 " 드라이브 온라인 상태 " 패턴이 나타납니다 . 주 : RAID 구성이 아닌 경우 드라이브 작동 표시등만 켜집니다 . 드라이브 상태 표시등은 켜지지 않습니다 .
표 1-3. RAID 구성용 하드 드라이브 표시등 패턴 조건 드라이브 상태 표시등 패턴 드라이브 분리 확인 / 준비 상태 녹색 표시등이 초당 두 번 깜박입니다 . 드라이브 설치 또는 분리 대기 상태 꺼짐 드라이브 장애 예고 상태 표시등이 녹색 , 호박색으로 깜박이거나 꺼집니다 . 드라이브 오류 상태 녹색 표시등이 초당 네 번 깜박임 드라이브 재구성 중 표시등이 녹색으로 천천이 깜박입니다 . 드라이브 온라인 녹색으로 켜져 있습니다 . 재구축 중단 상태 3 초 동안 녹색으로 , 3 초 동안 호박색으로 깜박이고 6 초 동안 꺼 집니다 . 후면 패널 구조 및 표시등 그림 1-3 은 시스템 후면 패널의 제어부 , 표시등 , 커넥터를 보여줍니다 . 그림 1-3.
외장형 장치 연결 시스템에 외장형 장치를 연결하는 경우 , 다음 지침을 따르십시오 . • 대부분의 장치는 지정된 커넥터에 연결되어야 하며 , 장치 드라이버를 설치해야만 장치가 올바르 게 작동합니다 . 대부분의 운영 체제 소프트웨어나 장치에는 해당 장치 드라이버가 포함되어 있습 니다 . 구체적인 설치 및 구성 방법은 장치와 함께 제공되는 설명서를 참조하십시오 . • 외장형 장치는 항상 시스템이 꺼진 상태에서 연결하십시오 . 그런 다음 설명서에 별도로 언급된 사 항이 없으면 외부 장치의 전원을 켠 다음 시스템을 켜십시오 . 개별 커넥터에 대한 자세한 내용은 117 페이지 " 점퍼 및 커넥터 " 를 참조하십시오 . I/O 포트 및 커넥터 를 활성화 , 비활성화 및 구성하는 데 대한 자세한 내용은 33 페이지 " 시스템 설치 프로그램 사용 " 을 참 조하십시오 . 전원 표시등 코드 전면 패널에 있는 전원 단추로 시스템의 전원 공급 장치에 대한 전원 입력을 제어합니다 .
그림 1-4. 전원 공급 장치 표시등 1 2 3 전원 공급 장치 상태 표시등 1 2 전원 공급 장치 장애 표시등 3 AC 라인 상태 표시등 NIC 표시등 코드 후면판의 각 NIC 에는 네트워크 작동 상태 및 연결 상태에 관한 정보를 제공하는 표시등이 있습니다 . 그림 1-5 를 참조하십시오 . 표 1-6 은 NIC 표시등 코드를 나열합니다 . 그림 1-5. NIC 표시등 1 1 2 연결 표시등 2 작동 표시등 표 1-6. NIC 표시등 코드 표시등 표시등 코드 연결 표시등 및 작동 표시등이 켜지 NIC 는 네트워크에 연결되지 않았음을 나타냅니다 . 지 않음 16 연결 표시등이 녹색으로 켜짐 NIC 가 네트워크의 유효한 연결부에 연결되어 있음을 나타 냅니다 . 작동 표시등이 호박색으로 깜박임 네트워크 데이타를 전송하거나 수신하는 중임을 나타냅니 다.
LCD 상태 메시지 시스템이 올바르게 작동하거나 시스템에 문제가 발생함을 알릴 경우 시스템 제어판 LCD 는 상태 메 시지를 표시합니다 . 시스템이 정상적으로 작동할 경우 LCD 는 청색으로 켜지고 오류가 발생할 경우에는 호박색으로 깜 박입니다 . LCD 는 설명 문자가 따른 상태 코드를 포함한 메시지를 표시합니다 . 표 1-7 은 발생할 수 있는 LCD 상태 메시지 및 각 메시지의 가능한 원인을 나열합니다 . LCD 메시지는 SEL( 시스템 이벤 트 로그 ) 에 기록된 이벤트를 나타냅니다 . SEL 및 시스템 관리 설정 구성에 대한 자세한 내용은 시 스템 관리 소프트웨어 설명서를 참조하십시오 . 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 .
표 1-7. LCD 상태 메시지 ( 계속 ) 18 코드 문자 원인 E1211 ROMB Batt RAID 전지도 장착되지 않았거 RAID 전지 커넥터를 다시 장착 나 문제가 발생했거나 온도 문제 하십시오 . 61 페이지 "RAID 전 로 재충전할 수 없습니다 . 지 " 및 103 페이지 " 시스템 냉각 문제 해결 " 을 참조하십시오 . E1229 CPU # VCORE 지정된 프로세서 # VCORE 전 127 페이지 " 도움말 얻기 " 를 참 압 조정기에 문제가 발생했습니 조하십시오 . 다. E1310 RPM Fan ## 특정된 냉각팬의 RPM 이 적당 한 작동 범위를 초과했습니다 . E1311 RPM Fan Mod #x # 모듈의 팬 x 의 RPM 이 적당한 103 페이지 " 시스템 냉각 문제 작동 범위를 벗어났습니다 . 해결 " 을 참조하십시오 . E1313 Fan Redundancy 시스템이 더이상 팬 중복을 지원 하지 않습니다 .
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 수정 조치 E1418 CPU # Presence 지정된 프로세서는 설치되지 않 110 페이지 " 마이크로프로세서 았거나 문제가 발생했거나 시스 문제 해결 " 을 참조하십시오 . 템에 지원되지 않는 구성입니다 . E141C CPU Mismatch Dell 에서 지원하지 않는 프로세 65 페이지 "System Memory" 를 서 구성입니다 . 참조하십시오. 프로세서가 해당 시스템 시작 안내서에 나와 있는 마이크로프로세서 기술 사양에 서 설명된 종류에 일치한지 확인 하십시오 . E141F CPU Protocol 프로세서 프로토콜 오류가 시스 127 페이지 " 도움말 얻기 " 를 참 템 BIOS 에 보고되었습니다 . 조하십시오 . E1420 CPU Bus PERR 프로세서 버스 패리티 오류가 시 127 페이지 " 도움말 얻기 " 를 참 스템 BIOS 에 보고되었습니다 . 조하십시오 .
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 E1624 PS Redundancy 전원 공급 서브시스템이 더이상 102 페이지 " 전원 공급 장치 문 중복되지 않습니다 . 마지막 공 제 해결 " 을 참조하십시오 . 급이 실패할 경우 시스템은 사용 할 수 없습니다 . E1710 I/O Channel Chk I/O 채널 점검이 시스템 BIOS 에 127 페이지 " 도움말 얻기 " 를 참 보고되었습니다 . 조하십시오 . E1711 PCI PERR B## D## PCI 구성 공간 ( 버스 ##, 장치 F## ##, 기능 ##) 에 상주한 구성요 소의 PCI 패리티 오류가 시스템 BIOS 에 보고되었습니다 . PCI PERR Slot # E1712 PCI 확장 카드를 분리한 다음 다 시 장착하십시오 . 문제가 지속 되면 127 페이지 " 도움말 얻기 " 을 참조하십시오 .
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 수정 조치 E1811 HDD ## Rbld Abrt 지정된 하드 드라이브에 재구축 106 페이지 "하드 드라이브 문제 중단이 발생했습니다 . 해결 " 을 참조하십시오 . 문제가 지속되면 RAID 설명서를 참조 하십시오 . E1812 HDD ## Removed 지정된 하드 드라이브가 시스템 참조 전용입니다 . 에서 분리되었습니다 . E1913 CPU & Firmware Mismatch BMC 펌웨어는 CPU 를 지원하 지 않습니다 . 최신 BMC 펌웨어로 업데이트하 십시오 . BMC 설치 및 사용법에 대한 자세한 내용은 BMC 사용 설명서를 참조하십시오 . E1A14 SAS Cable A SAS 케이블 A 가 분실되었거나 고장 상태입니다 . 케이블을 다시 장착하십시오 . 문제가 지속되면 케이블을 교체 하십시오 . 58 페이지 "SAS 컨트 롤러 보조 카드 " 를 참조하십시 오.
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 수정 조치 E2013 Shadow BIOS Fail 시스템 BIOS 는 해당 플래시 이 104 페이지 "시스템 메모리 문제 미지를 메모리에 복사하는 데 실 해결 " 을 참조하십시오 . 패했습니다 . E2014 CMOS Fail CMOS 오류입니다 . CMOS RAM 이 올바르게 작동하지 않 습니다 . 127 페이지 " 도움말 얻기 " 를 참 조하십시오 . E2015 DMA Controller DMA 컨트롤러 오류입니다 . 127 페이지 " 도움말 얻기 " 를 참 조하십시오 . E2016 Int Controller 컨트롤러 간섭 오류입니다 . 127 페이지 " 도움말 얻기 " 를 참 조하십시오 . E2017 Timer Fail 타이머 새로 고침 오류입니다 . 127 페이지 " 도움말 얻기 " 를 참 조하십시오 .
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 수정 조치 E2021 Memory Population 정확하지 않은 메모리 구성입니 특정 오류 메시지를 확인하십시 다 . 메모리 배치 절차가 정확하 오 . 104 페이지 " 시스템 메모리 지 않습니다 . 문제 해결 " 을 참조하십시오 . E2022 POST Fail 비디오 설치 후의 일반 오류입니 특정 오류 메시지를 확인하십시 다. 오. E2110 MBE Crd # DIMM ## "## & ##" 와 관련된 세트의 104 페이지 "시스템 메모리 문제 & ## DIMM 중 하나에 메모리 MBE( 해결 " 을 참조하십시오 . 멀티 비트 오류 ) 가 발생했습니 다 . 메모리 카드가 없으면 "Crd #" 문자열이 메시지에서 삭제됩 니다 .
표 1-7. LCD 상태 메시지 ( 계속 ) 코드 문자 원인 수정 조치 E2119 Fatal SB Mem CRC 남쪽의 FBD 메모리 서브시스템 104 페이지 "시스템 메모리 문제 연결 중 하나에 오류가 발생했습 해결 " 을 참조하십시오 . 니다 . I1910 Intrusion 시스템 덮개가 분리되었습니다 . 참조 전용입니다 . I1911 >3 ERRs Chk Log LCD 오버플로 메시지입니다 . I1912 SEL Full 시스템 이벤트 로그에는 이벤트 이벤트 항목을 삭제하여 로그를 가 차있으며 더이상 이벤트를 로 제거하십시오 . 그할 수 없습니다 . W1228 ROMB Batt < 24hr RAID 전지가 24 시간 미만의 충 RAID 전지를 교체하십시오 . 61 전량만 남았음을 사전 경고합니 페이지 "RAID 전지 " 를 참조하 다. 십시오 . 이벤트에 대한 세부사항은 SEL 을 참조하십시오 . 최대 세 개의 오류 메시지를 LCD 에 순차적으로 표시할 수 있습니다 .
이러한 모든 작업은 오류 메시지를 제거하며 상태 표시등 및 LCD 색상을 정상 상태로 복귀합니다 . 다음 조건에서 메시지는 다시 나타납니다 . • 센서가 정상 작동 상태로 회복되었지만 다시 실패하여 새 SEL 항목을 초래했습니다 . • 시스템이 재설정되고 새 오류 이벤트가 감지되었습니다 . • 동일한 디스플레이 항목에 매핑한 다른 소스에서 오류가 보고되었습니다 . 시스템 메시지 시스템의 발생 기능한 문제를 알려 줄 경우 화면에 시스템 메시지가 표시됩니다 . 표 1-8 에서는 표시 될 수 있는 시스템 메시지 및 각 메시지의 가능한 원인과 조치를 나열합니다 . 주 : 표 1-8 에 나열되지 않은 메시지가 표시되면 메시지가 표시될 때 실행 중인 응용프르그램의 설명서를 참조하거나 운영 체제의 설명서를 참조하여 메시지에 대한 해석 및 제안된 작업을 확인하십시오 . 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 .
표 1-8. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 DIMM pairs must be matched 불일치한 DIMM 이 설치되었습니다 . in size, speed, and 메모리 모듈에 결함이 있거나 올바 technology. The following 르게 장착되어 있지 않습니다 . DIMM pair is mismatched: DIMM x and DIMM y. 모든 메모리 모듈 쌍이 동일한 유형 및 크기이고 올바르게 설치되었는지 확인 하십시오 . 65 페이지 "System Memory" 를 참조하십시오 . 문제가 지속되면 104 페이지 " 시스템 메모리 문제 해결 " 을 참조하십시오 . DIMMs must be populated in sequential order beginning with slot 1. The following DIMM is electrically isolated: DIMM x. 위치로 인해 특정 DIMM 이 시스템 에 액세스할 수 없습니다 .
표 1-8. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 FBD training error: The following branch has been disabled: Branch x 특정 분기 ( 채널 ) 에 서로 호환되지 Dell 사에서 공인한 메모리만 사용하십 않는 DIMM 이 포함되어 있습니다 . 시오 . 호환성을 보증하기 위하여 www.dell.com 또는 Dell 판매처에서 직 접 메모리 업그레이드 키트를 구입하 는 것이 좋습니다 . Gate A20 failure 키보드 컨트롤러 및 시스템 보드에 결함이 있습니다 . 127 페이지 " 도움말 얻기 " 를 참조하십 시오 . General failure 운영 체제가 명령을 실행할 수 없습 니다 . 이 메시지는 특정 정보와 함께 표시됩 니다 . 문제를 해결하려면 이 정보를 기 록하고 적절한 조치를 취하십시오 .
표 1-8. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 No boot device available 광학 드라이브 서브시스템 , 하드 드 라이브 또는 하드 드라이브 서브시 스템에 결함이 있거나 설치되지 않 았거나 또는 드라이브 A 에 부팅 디 스크가 없습니다 . CD 나 하드 드라이브를 사용하십시오 . 문제가 지속되면 105 페이지 " 광학 드 라이브 문제 해결 " 및 106 페이지 " 하 드 드라이브 문제 해결 " 을 참조하십시 오 . 부팅 장치의 순서를 설정하는 데 대 한 정보는 33 페이지 " 시스템 설치 프 로그램 사용 " 을 참조하십시오 . No boot sector on hard drive 시스템 설치 프로그램에 정확하지 않은 구성 설정이 있거나 하드 드라 이브에 운영 체제가 없습니다 . 시스템 설치 프로그램의 하드 드라이 브 구성 설정을 확인하십시오 . 33 페이 지 " 시스템 설치 프로그램 사용 " 을 참 조하십시오 .
표 1-8. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 PCI BIOS failed to install 그림자 설정 중에 PCI 장치 BIOS( 선 확장 카드를 다시 장착하십시오 . 해당 택 사양 ROM) 체크섬 오류가 감지되 케이블이 모두 확장 카드에 단단히 연 었습니다 . 결되어 있는지 확인하십시오 . 문제가 확장 카드에 연결된 케이블이 느슨 지속되면 109 페이지 " 확장 카드 문제 하게 되었습니다 . 설치된 확장 카드 해결 " 을 참조하십시오 . 에 결함이 있거나 잘못 설치되었습 니다 . Plug & Play Configuration Error PCI 장치를 초기화하는 데 오류가 발 NVRAM_CLR 점퍼를 설치하고 시스템 생했습니다 . 시스템 보드에 결함이 을 재부팅하십시오 . 점퍼 위치에 관한 있습니다 . 내용은 그림 6-1 을 참조하십시오 . 문 제가 지속되면 109 페이지 " 확장 카드 문제 해결 " 을 참조하십시오 .
표 1-8. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 Time-of-day clock stopped 전지 또는 칩에 결함이 있습니다 . 102 페이지 " 시스템 전지 문제 해결 " 을 참조하십시오 . The following DIMM pair is 지정된 DIMM 이 시스템과 호환되 not compatible with the 지 않습니다 . memory controller: DIMM x and DIMM y Dell 사에서 공인한 메모리만 사용하십 시오 . 호환성을 보증하기 위하여 www.dell.com 또는 Dell 판매처에서 직 접 메모리 업그레이드 키트를 구입하 는 것이 좋습니다 . The following DIMMs are 지정된 DIMM 이 시스템과 호환되 not compatible: DIMM x and 지 않습니다 . DIMM y ECC FBD1 메모리만 사용하십시오 . 호환성을 보증하기 위하여 www.dell.
진단 메시지 시스템 진단 프로그램을 실행할 경우 오류 메시지가 표시됩니다 . 본 절에서는 오류 진단 메시지에 관한 내용을 설명하지 않습니다 . 127 페이지 " 도움말 얻기 " 에 있는 진단 점검사항의 사본에 메시지 를 기록한 다음 해당 절의 지침에 따라 기술 지원을 획득하십시오 . 경고 메시지 시스템 관리 소프트웨어는 해당 시스템에 대한 경고 메시지를 생성합니다 . 경고 메시지에는 드라이 브 , 온도 , 팬 및 전원 조건에 관한 정보 , 상태 , 경고 및 오류 메기지가 포함됩니다 . 자세한 내용은 시 스템 관리 소프트웨어 설명서를 참조하십시오 .
시스템 정보
시스템 설치 프로그램 사용 시스템을 설치한 후 , 시스템 설치 프로그램을 실행하여 시스템의 구성 정보 및 옵션 설정값을 확인하십시오 . 나중에 참조할 수 있도록 정보를 기록해 두십시오 . 시스템 설치 프로그램을 사용하여 다음 작업을 수행할 수 있습니다 . • 하드웨어를 추가 , 변경 또는 분리한 후 NVRAM 에 저장된 시스템 구성을 변경 • 시간 또는 날짜와 같이 사용자가 선택할 수 있는 옵션을 설정하거나 변경 • 내장형 장치를 활성화하거나 비활성화 • 설치된 하드웨어와 구성 설정 사이의 불일치 수정 시스템 설치 프로그램 시작 1 시스템을 켜거나 재시작하십시오 . 2 다음과 같은 메시지가 나타나면 , 즉시 키를 누르십시오 . = System Setup 키를 누르기 전에 운영 체제가 로드되기 시작하면 시스템이 부팅을 완성하게 한 다음 시스템을 재시작하고 다시 시도하십시오 .
표 2-1. 시스템 설치 프로그램 탐색 키 키 조치 위쪽 화살표 또는 이전 필드로 이동합니다 . 키 아래쪽 화살표 또는 키 다음 필드로 이동합니다 . 스페이스바 , <+>, <->, 왼쪽 및 필드의 설정 사이를 이동합니다 . 대부분의 필드에 오른쪽 화살표 서는 해당 값을 입력할 수 있습니다 . 시스템 설치 프로그램을 종료하고 변경 사항이 있 는 경우 시스템을 재시작합니다 . 시스템 설치 프로그램의 도움말 파일을 표시합니 다. 주 : 대부분의 옵션은 시스템을 재시작해야만 변경사항이 적용됩니다 . 시스템 설치 옵션 기본 화면 시스템 설치 프로그램을 시작하면 , 시스템 설치 프로그램 기본 화면이 나타납니다 ( 그림 2-1 참조 ).
그림 2-1. 시스템 설치 프로그램 기본 화면 표 2-2 에는 시스템 설치 프로그램 기본 화면에 있는 옵션과 정보 필드의 설명이 표시됩니다 . 관련된 정보는 39 페이지 "System Security 화면 옵션 " 을 참조하십시오 . 주 : 시스템 설치 프로그램의 옵션은 시스템 구성에 따라 변경됩니다 . 주 : 시스템 설치 프로그램 기본값은 각 해당 옵션 아래에 표시됩니다 . 표 2-2. 시스템 설치 프로그램 옵션 옵션 설명 System Time 시스템 내부 클럭 시간을 재설정합니다 . System Date 시스템 내부 달력의 날짜를 재설정합니다 . 메모리 정보 메모리 모듈의 크기 , 종류 및 속도 , 시스템 메모리 검사 옵션 상태 및 중복 메모 리 상태를 포함하는 설치된 시스템 , 비디오 및 중복 메모리에 관련된 정보를 표 시합니다 . CPU Information 마이크로프로세서와 관련된 정보를 표시합니다 ( 속도 , 캐쉬 크기 등 ).
표 2-2. 시스템 설치 프로그램 옵션 ( 계속 ) 옵션 설명 Boot Sequence 시스템 시작 과정에서 시스템이 부팅 장치를 검색하는 순서를 결정합니다 . 사 용 가능한 옵션은 디스켓 드라이브 , CD 드라이브 , 하드 드라이브 및 네트워크 입니다 . RAC 가 설치되어 있는 경우 가상 플로피 및 가상 CD-ROM 과 같은 추 가 옵션이 있을 수 있습니다 . 주 : SAS 또는 SCSI 에 연결된 외부 장치에서는 시스템 부팅을 지원하지 않습니 다 . 외부 장치에서 부팅하는 데 관한 최신 지원 정보는 support.dell.com 을 참조 하십시오 . USB Flash Drive Type (Auto 기본값 ) USB 플래쉬 드라이브에 대한 에뮬레이션 종류를 지정합니다 . Hard disk 를 사 용하면 USB 플래쉬 드라이브가 하드 드라이브로 작동할 수 있습니다 . Floppy 를 사용하면 USB 플래쉬 드라이브가 분리 디스켓 드라이브로 작동할 수 있습니 다 .
CPU Information 화면 표 2-3 은 CPU Information 화면에 있는 옵션과 정보 필드에 대한 설명입니다 . 표 2-3. CPU Information 화면 옵션 설명 Bus Speed 프로세서의 버스 속도를 표시합니다 . Logical Processor (Enabled 기본값 ) 프로세서가 하이퍼스레딩을 지원하는 경우 표시됩니다 . Enabled 로 설정하면 선택하면 운영 체제에서 모든 논리 프로세 서를 사용할 수 있습니다 . Disabled 를 선택한 경우 시스템에 설 치된 각 프로세서의 첫 번째 논리 프로세서만 사용합니다 . Virtualization Technology (Disabled 기본값 ) 프로세서가 가상화 기술을 지원할 경우 표시됩니다 . Enabled 로 설정하면 가상화 소프트웨어가 프로세서를 설계할 때 통합된 가상화 기술 기능을 사용할 수 있게 합니다 . 이 기능은 가상화 기술을 지원하는 소프트웨어에서만 사용할 수 있습니다 .
Integrated Devices 화면 표 2-4 는 Integrated Devices 화면에 있는 옵션과 정보 필드에 대한 설명입니다 . 표 2-4. Integrated Devices 화면 옵션 옵션 설명 Integrated SAS Controller 내장형 SAS 컨트롤러를 활성화하거나 비활성화합니다 . (Enabled 기본값 ) Embedded SATA Controller (Off 기본값 ) 내장형 SATA 컨트롤러를 Off 또는 ATA 모드로 설정할 수 있습니다 . IDE CD-ROM Controller 내장형 IDE 컨트롤러를 활성화합니다 . Auto 로 설정하면 , IDE 장치가 채널에 연 (Auto 기본값 ) 결되어 있고 외장형 IDE 컨트롤러가 감지되지 않을 경우 , 내장형 IDE 컨트롤러 의 각 채널은 활성화됩니다 . 주 : 시스템에 이 선택 사양인 장치가 포함되지 않으면 이 CD-ROM 옵션은 이 메 뉴 화면에 나타나지 않습니다 .
System Security 화면 표 2-5 는 System Security 화면에 있는 옵션과 정보 필드에 대한 설명입니다 . 표 2-5. System Security 화면 옵션 옵션 설명 System Password 시스템 암호 보안 기능의 현재 상태를 표시하며 새 시스템 암호를 지정하고 확 인할 수 있습니다 . 주 : 시스템 암호 지정 및 기존 시스템 암호를 사용하거나 변경하는 자세한 내용 은 40 페이지 " 시스템 암호 사용 " 을 참조하십시오 . Setup Password 시스템 암호 기능으로 시스템에 대한 액세스를 제한하는 것과 같은 방식으로 시스템 설치 프로그램에 대한 액세스를 제한합니다 . 주 : 설치 암호 지정 및 기존 설치 암호를 사용하거나 변경하는 자세한 내용은 42 페이지 " 설치 암호 사용 " 을 참조하십시오 .
종료 화면 키를 눌러 시스템 설치 프로그램을 종료한 후 , Exit 화면에 다음과 같은 옵션이 표시됩니다 . • Save Changes and Exit • Discard Changes and Exit • Return to Setup 시스템 및 설치 암호 기능 주의사항 : 암호 기능은 시스템 데이타에 대한 기본적인 수준의 보안을 제공합니다 . 데이타를 보다 안전 하게 보호하려면 , 데이타 암호화 프로그램 같은 보호 수단을 추가로 사용하십시오 . 주의사항 : 시스템 암호를 지정하지 않고 시스템을 실행하던 도중에 자리를 비우면 누구든지 하드 드라이 브에 저장되어 있는 데이타에 액세스할 수 있으며 , 시스템을 잠그지 않고 자리를 비우면 다른 사람이 점퍼 설정을 변경하여 암호를 비활성화할 수 있습니다 . 본 시스템은 시스템 암호 기능이 활성화되지 않은 상태로 출하됩니다 . 보안이 필요한 시스템인 경우 , 시스템 암호 보안 기능이 있는 시스템을 사용해야 합니다 .
암호에는 최대 32 자까지 지정할 수 있습니다 . 각 문자 키 ( 또는 빈 칸의 경우 스페이스바 ) 를 누를 때마다 필드에 위치 지정자가 표시됩니다 . 암호는 대소문자를 구분하지 않습니다 . 그러나 일부 키 조합은 유효하지 않습니다 . 암호 입력 시 문자를 지우려면 키 또는 왼쪽 화살표 키를 누르십시오 . 주 : 시스템 암호를 지정하지 않고 다른 필드로 이동하려면 를 누르거나 5 단계를 실행하기 이 전에 를 누르십시오 . 4 키를 누르십시오 . 5 암호를 확인하려면 , 다시 암호를 입력하고 키를 누르십시오 . System Password 의 설정값이 Enabled 로 변경됩니다 . 시스템 설치 프로그램을 종료하면 시스템 이 시작됩니다 . 6 암호 보안 기능을 사용하기 위해서 지금 시스템을 재부팅하거나 작업을 계속 진행하십시오 . 주 : 암호 보안 기능은 시스템을 재부팅해야만 적용됩니다 .
기존 시스템 암호 삭제 또는 변경 1 메시지가 표시될 때 키를 누르면 기존의 시스템 암호가 비활성화됩니다 . 설치 암호를 입력하라는 메시지가 나타나면 네트워크 관리자에게 문의하십시오 . 2 POST 동안 를 눌러 시스템 설치 프로그램을 시작하십시오 . 3 System Security 화면 필드를 선택하여 Password Status 옵션이 Unlocked 로 설정되어 있는지 확인 하십시오 . 4 입력 창이 나타나면 시스템 암호를 입력하십시오 . 5 System Password 옵션이 Not Enabled 로 표시되어 있는지 확인하십시오 . System Password 옵션이 Not Enabled 로 표시되면 시스템 암호는 삭제된 것입니다 . System Password 옵션이 Enabled 로 표시되어 있는 경우 , 키 조합을 눌러 시스템을 재시작한 다음 2 단계 ~5 단계를 반복 수행하십시오 .
세 번의 기회 동안 올바른 암호를 입력하지 않으면 시스템 설치 프로그램을 볼 수만 있고 변경할 수 는 없습니다 . 다음의 경우는 예외입니다 . System Password 가 Enabled 로 설정되어 있지 않고 Password Status 옵션의 잠금이 해제 상태인 경우 시스템 암호를 지정할 수 있습니다 . 그러나 기존 시 스템 암호를 비활성화하거나 변경할 수는 없습니다 . 주 : 시스템 암호가 무단으로 변경되는 것을 방지하려면 Setup Password 옵션과 Password Status 옵션을 결 합하여 사용할 수 있습니다 . 기존 설치 암호 삭제 또는 변경 1 시스템 설치 프로그램을 시작하여 System Security 옵션을 선택하십시오 . 2 Setup Password 옵션을 선택하고 키를 누르면 설치 암호 창에 액세스할 수 있습니다 . 기 존 설치 암호를 지우려면 키를 두 번 누르십시오 . 설정이 Not Enabled 로 변경됩니다 .
BMC 설치 모듈 옵션 설치 모듈 옵션 및 비상 관리 포트 (EMP) 의 구성 방법에 대한 정보는 BMC 사용 설명서를 참조하십시 오.
시스템 구성요소 설치 이 절에서는 다음 구성요소를 설치하는 방법을 설명합니다 .
권장된 도구 본 절의 절차를 수행하려면 다음 항목이 필요할 수 있습니다 . • 시스템 키 잠금의 키 • #2 십자 드라이버 • T10 별 드라이버 • 소형 일자 드라이버 • 손목접지대 시스템 내부 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 주의 : 정상 작동 과정에 메모리 모듈이 매우 뜨거워질 수 있습니다 . 모듈을 다루기 전에 충분히 냉각될 때 까지 기다리십시오 . 그림 3-1 에서 베젤 , 시스템 덮개 및 메모리 냉각 덮개가 분리되어 시스템의 내부 모습을 제공합니다 . 그림 3-1.
측면판 1 제어판 2 SAS 컨트롤러 보조 카드 또 는 SAS RAID 컨트롤러 보조 카드 ( 선택 사양 ) 3 4 냉각팬 모듈 (4 개 ) 5 전원 공급 장치 베이 (2 개 ) 6 좌측 라이저 ( 슬롯 2) 7 중앙 라이저 ( 슬롯 1) 8 전지 9 시스템 보드 냉각 덮개 10 메모리 모듈 (8 개 ) 11 방열판 / 마이크로프로세서 (2 개 ) 12 후면판 13 2 개의 3.5 인치 또는 3 개의 2.5 인치 하드 드라이브 베이 14 광학 슬림라인 드라이브 ( 선 택 사양 ) 시스템 보드는 시스템의 제어 회로 및 기타 전기 구성요소를 수용합니다 . 마이크로프로세서 및 메모 리와 같은 여러 하드웨어 옵션은 시스템 보드에 직접 설치되어 있습니다 . 각 좌측 및 중앙 라이저에 는 슬롯이 하나씩 있고 최대로 두 개의 half-length PCI-X 카드 또는 두 개의 half-length PCIe 확장 카 드를 수용할 수 있습니다 .
그림 3-2. 베젤 분리 1 2 1 키 잠금 2 베젤 덮개 전면 베젤을 장착하려면 앞의 단계를 역순으로 수행하십시오 . 시스템 열기 및 닫기 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 주의 : 시스템을 들어야 하는 경우에는 도움을 청하십시오 . 부상을 입는 것을 방지하려면 시스템을 혼자 서 들지 마십시오 . 주의 : 정상 작동 과정에 메모리 모듈이 매우 뜨거워질 수 있습니다 . 모듈을 다루기 전에 충분히 냉각될 때 까지 기다리십시오 . 시스템 열기 시스템을 업그레이드하거나 문제를 해결하려면 시스템 덮개를 분리하여 내부 구성요소에 접근하십시 오. 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트 및 주변 장치에서 분리하십시오 . 2 베젤을 분리하십시오 .
4 시스템 상단의 래치를 들어 올려 뒤로 돌린 다음 오프셋 위치에 놓으십시오. 그림3-3을 참조하십시 오. 5 덮개의 양쪽을 잡고 시스템에서 덮개를 조심스럽게 들어올리십시오 . 그림 3-3. 덮개 분리 1 2 3 4 1 래치 4 섀시 탭 2 래치 분리 잠금 3 맞춤 J 고리 시스템 닫기 1 덮개의 래치를 들어 올리십시오 . 2 섀시의 J 고리에서 분리하고 시스템 섀시에 평평하게 놓이도록 덮개를 시스템의 상단에 놓고 뒤로 약간 간격을 띄우십시오 . 그림 3-3 을 참조하십시오 . 3 덮개를 J 고리에 맞추어 닫힌 위치로 내린 다음 덮개를 제자리에 고정하도록 래치를 아래로 누르십 시오 . 4 래치 분리 잠금을 시계 방향으로 회전하여 덮개를 고정하십시오 .
냉각팬 모듈 본 시스템은 시스템 보드에 직접 연결된 총 8 개 팬의 4 개의 냉각팬 모듈을 포함하며 각 냉각팬 모듈은 2 개의 이중 로터 팬으로 구성됩니다 . 냉각팬 모듈 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 주 : 각 개별 팬 모듈의 분리 절차는 동일합니다 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트 및 주변 장치에서 분리하십시오 . 2 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 주 : 메모리 냉각 덮개를 분리하지 않고 팬 모듈을 분리할 수 있지만 팬 모듈을 분리하기 전에 이 덮개를 분 리하는 것이 좋습니다 . 시스템 보드 냉각 덮개를 분리하지 마십시오 . 54 페이지 " 메모리 냉각 덮개 분리 " 를 참조하십시오 .
그림 3-4. 냉각팬 분리 및 설치 2 3 1 4 5 1 냉각팬 모듈 (4 개 ) 2 팬 모듈 핸들 4 냉각팬 모듈 커넥터 5 시스템 보드 냉각 덮개 3 모듈 유선 장비 냉각팬 모듈 장착 주 : 각 개별 팬의 설치 절차는 동일합니다 . 1 팬 핸들이 똑바로 세워졌는지 확인하고 팬이 완전히 장착될 때까지 해당 고정 베이스로 내리십시 오 . 그런 다음 팬 핸들이 제자리에 걸릴 때까지 내리십시오 . 그림 3-4 를 참조하십시오 . 2 팬 모듈 커넥터를 장착하십시오 . 3 팬 모듈에 접근하기 위해 메모리 냉각 덮개를 분리한 경우 덮개를 장착하십시오 . 55 페이지 " 메모 리 냉각 덮개 장착 " 을 참조하십시오 . 4 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 .
플라스틱 팬 가이드 분리 주 : 플라스틱 팬 가이드는 팬들 사이 섀시에 장착됩니다 . 주 : 랙에서 시스템을 분리해야 할 수도 있습니다 . 1 냉각 팬 모듈을 분리합니다 . 50 페이지 " 냉각팬 모듈 분리 " 을 참조하십시오 . 2 랙에서 시스템을 분리합니다 . 시스템의 랙 설치 안내서 를 참조하십시오 . 3 평평한 표면에 시스템을 뒤집어서 놓습니다 4 #2 십자 드라이버로 섀시 바닥에서 팬 브래킷을 고정시키고 있는 두 개의 나사를 분리합니다 . 5 시스템 오른쪽이 위를 향하게 해서 평평판 표면에 놓은 후 팬 브래킷을 분리합니다 . 플라스틱 팬 가이드 교체 1 시스템이 랙에서 빠진 동안 상단 덮개가 분리된 상태로 시스템을 평평한 표면에 옆으로 뉘어 놓습 니다 . 2 팬 브래킷을 섀시 내부의 해당 위치에 놓습니다 . 3 팬 브래킷을 제자리에 고정시킨 후 #2 십자 드라이버로 섀시 바닥에 두 개의 나사를 다시 끼웁니 다. 4 평평한 표면에 시스템이 오른쪽 위를 향하도록 해서 놓습니다 .
그림 3-5. 시스템 보드 냉각 덮개 1 1 시스템 보드 냉각 덮개 시스템 보드 냉각 슈라우드 분리 1 해당하는 경우 베젤을 분리합니다 . 47 페이지 " 전면 베젤 분리 및 장착 " 를 참조하십시오 . 2 시스템과 주변 기기를 끈 후 전기 콘센트에서 시스템을 분리합니다 . 3 시스템을 엽니다 . 48 페이지 " 시스템 열기 " 를 참조하십시오 . 4 메모리 냉각 슈라우드를 분리합니다 . 54 페이지 " 메모리 냉각 덮개 분리 " 를 참조하십시오 . 5 가운데 및 왼쪽 라이저 모두를 시스템 보드에서 분리합니다. 83 페이지 "확장 카드 라이저 분리"를 참조하십시오 . 6 프로세서와 가장 가까이 있는 슈라우드 전면의 탭을 누른 후 슈라우드를 위로 들어올린 후 시스템 에서 떼어냅니다 . 시스템 보드 냉각 슈라우드 설치 1 슈라우드 뒷면을 마더보드의 가운데 및 후면 카드 라이저 기둥 앞에 맞춥니다 . 2 슈라우드 전면이 마더보드의 플라스틱 탭에 맞물릴 때까지 살짝 누릅니다 .
7 주변 기기를 연결하고 시스템을 전원에 연결한 후 시스템 전원을 켭니다 . 메모리 냉각 덮개 메모리 냉각 덮개는 메모리 모듈 (DIMM) 및 프로세서를 모두 보호합니다 . 이 덮개는 분리하고 설치할 수 있습니다 . 그림 3-6 및 92 페이지 " 시스템 보드 분리 " 를 참조하십시오 . 메모리 냉각 덮개 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 주의 : 시스템의 전원을 끈 후 메모리 모듈은 뜨거우므로 일정한 시간 동안 다치지 마십시오 . 메모리 모듈 을 다루기 전에 냉각될 때까지 기다리십시오 . 메모리 모듈을 다루는 경우 카드 모서리를 잡아야 하며 메모 리 모듈의 단자를 다치지 마십시오 . 주의사항 : 메모리 냉각 덮개를 분리한 상태에서 컴퓨터를 작동하지 마십시오 .
그림 3-6. 메모리 냉각 덮개 1 2 3 4 1 메모리 냉각 덮개 4 시스템 프로세서 (2 개 ) 2 메모리 덮개 분리 탭 3 메모리 모듈 (8 개 ) 메모리 냉각 덮개 장착 1 메모리 냉각 덮개를 설치하려면 덮개를 메모리 모듈 및 프로세서 위에 직접 맞추십시오 . 2 내장형 시스템 보드 냉각 덮개를 가이드로 사용하여 프로세서 및 메모리 모듈 위에 직접 놓이도록 덮개를 아래로 시스템에 천천히 내리십시오 . 3 외부 탭에 맞물리고 제자리에 걸릴 때까지 덮개의 주변 장치 주위를 조심스럽게 누르십시오 . 전원 공급 장치 해당 시스템은 하나 또는 두 개의 670W 출력 전원 공급 장치를 지원합니다 . 하나의 전원 공급 장치 만 설치할 경우 좌측 전원 공급 장치 베이 ( 베이 1) 에 설치해야 합니다 . 두개의 전원 공급 장치를 설 치할 경우 보조 전원은 보조 핫 플러그 전원 공급처럼 작동합니다 .
전원 공급 장치 분리 주의사항 : 시스템이 정상으로 작동하려면 1 개의 전원 공급 장치가 설치되어야 합니다 . 두 개의 전원 공 급 장치가 설치되고 모두 AC 전원에 연결된 경우 시스템은 중복 모드로 작동합니다 . 시스템이 한 전원 공 급 장치에만 연결되도록 장치를 연결하십시오 . 시스템이 전원 공급 장치 블랭크를 설치하지 않은 상태에 서 하나의 전원 공급 장치로 오랫동안 작동하는 경우 시스템이 과열될 수 있습니다 . 주의사항 : 하나의 전원 공급 장치만 설치할 경우 좌측 전원 공급 장치 베이 (1) 에 설치해야 합니다 . 주의사항 : 시스템을 120~220VAC 범위인 전원에 연결한 경우 2 개의 전원 공급 장치가 설치되어 있으면 보 조 전원 공급 장치는 중복 , 핫 플러그 전원의 작용을 합니다 . 주 : 랙 시스템에서 케이블 관리대가 전원 공급 장치 분리를 방해하는 경우 케이블 관리대를 열고 들어 올 려야 할 수 있습니다 . 케이블 관리대에 대한 정보는 시스템의 랙 설치 안내서를 참조하십시오 .
1 전원 공급 장치 2 전원 공급 장치 핸들 3 케이블 고정 브래킷 4 전원 공급 장치 블랭크 5 전원 공급 장치 베이 2( 선택 사양 ) 6 중복 전원 공급 장치 베이 1 7 잠금 탭 전원 공급 장치 장착 1 보조 전원 공급 장치를 추가하는 경우 전원 공급 장치 블랭크를 분리하십시오 . 56 페이지 " 전원 공 급 장치 분리 " 를 참조하십시오 . 2 전원 공급 장치 핸들을 잡은 상태에서 완전히 장착되고 시스템 섀시에 접촉할 때까지 새 전원 공급 장치를 섀시에 밀어 넣으십시오 . 그림 3-7 을 참조하십시오 . 주의사항 : 랙 시스템에서 케이블 관리대를 임시적으로 분리하고 들어야 할 수 있습니다 . 케이블 관리대 에 대한 정보는 시스템의 랙 설치 안내서를 참조하십시오 . 3 케이블 고정 브래킷을 통해 전원 케이블을 삽입하고 전원 공급 장치에 전원 케이블을 연결한 다음 해당 케이블을 전원 콘센트에 꽂으십시오 .
전원 공급 장치 블랭크 분리 베이에서 분리하도록 블랭크를 조금 돌리면서 왼쪽의 래치를 눌러 블랭크를 분리하고 섀시에서 빼 내십시오 . 주의사항 : 시스템의 적합한 온도를 보장하려면 전원 공급 블랭크는 중복 구성이 없는 전원 공급 베이에 설치되어야 합니다 . 보조 전원 공급 장치를 설치한 경우에만 전원 공급 장치 블랭크를 분리하십시오 . 전원 공급 장치 블랭크 설치 전원 공급 장치 블랭크를 설치하려면 블랭크 우측 모서리의 탭을 전원 공급 장치 베이 벽에 있는 슬 롯에 삽입하십시오 . 블랭크가 전원 공급 장치 베이에 완전히 장착될 때까지 회전하십시오 . SAS 컨트롤러 보조 카드 본 시스템은 측면판에 선택 사양인 SAS 컨트롤러 보조 카드 전용 슬롯이 있습니다 . SAS 컨트롤러 보 조 카드는 해당 시스템의 두 개 선택 사양인 내장형 하드 드라이브를 위해 SAS 저장 서브시스템을 제 공합니다 .
그림 3-8. SAS 컨트롤러 보조 카드 설치 4 3 2 5 1 6 7 8 1 SAS 컨트롤러 보조 카드 및 트레이 조립품 2 측면판 3 보조 카드 소켓 4 분리 래치 5 RAID 전지 커넥터 (SAS RAID 컨트롤러 보조 카드 전용 ) 6 RAID 메모리 모듈 (DIMM)(SAS RAID 컨트롤러 보조 카드 전용 ) 7 SAS RAID 커넥터 0( 후면판 SAS A 에 연결 ) 8 카드 트레이의 맞춤 슬롯 (2 개 ) 4 내장형 저장 보조 카드의 모든 케이블을 후면판에 연결하십시오 . 시스템 카드 및 후면판 구성에 대 한 케이블 연결 지침에 대해서는 그림 3-9, 그림 3-10 을 참조하십시오 . 주의사항 : 올바른 연결을 위해 하드 드라이브를 다음 그림에서 설명한 각 내장형 저장 보조 카드에 연결 하는 데 대한 케이블 연결 다이어그램을 따르십시오 .
그림 3-9.
그림 3-10. SAS RAID 컨트롤러 보조 카드에 대한 케이블 라우팅 3 2 1 1 SAS RAID 커넥터 SAS 0 2 SAS RAID 컨트롤러 보조 카드 3 SAS 후면판 커넥터 SAS A RAID 전지 RAID 전지 설치 1 하드 드라이브 베이 0 에 인접한 섀시의 RAID 전지 포켓을 찾으십시오 . 그림 3-11 을 참조하십시오 . 2 전지를 전지 포켓에 삽입하십시오 . 3 전지 케이블을 RAID 컨트롤러 보조 카드에 연결하십시오 . 그림 3-11 을 참조하십시오 .
그림 3-11. SAS RAID 전지 설치 2 3 1 1 RAID 전지 2 SAS RAID 보조 카드 전지 커 넥터 3 분리 래치 RAID 전지 분리 1 RAID 전지 케이블을 SAS RAID 보조 카드에서 분리하십시오 . 그림 3-11 을 참조하십시오 . 2 분리 래치를 하드 드라이브 베이를 향해 밀고 전지를 전지 포켓에서 분리하십시오 . 확장 카드 본 시스템에서 두 선택 사양인 PCI 라이저 구성 중의 하나를 사용할 수 있습니다 . PCIe 라이저 보드 확장 슬롯 PCIe 라이저 구성은 다음 구조를 가진 두 개의 PCI Express 확장 슬롯을 제공합니다 .
PCI-X 라이저 보드 확장 슬롯 PCI-X 라이저 구성은 다음 구조를 가진 두 개의 PCI-X 슬롯을 제공합니다 . • 좌측 및 중앙 라이저 커넥터에 설치된 두 개의 PCI-X 라이저 • 두 개의 PCI-X 64 비트 /133MHz 확장 슬롯 ( 별도의 버스에 있음 ) • 두 슬롯의 full height/half-length PCI 카드 지원 확장 카드 설치 지침 주 : PCIe 와 PCI-X 라이저를 결합할 수 없습니다 . 시스템 전원이 켜지도록 두 라이저를 함께 설치해야 합니 다. 주 : 확장 카드 슬롯은 핫 플러그 가능하지 않습니다 . 확장 슬롯을 식별하려면 그림 3-12 를 참조하십시오 . 두 확장 카드 슬롯은 별도의 버스에 있습니다 . 확장 카드 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 .
그림 3-12. 확장 카드 설치 3 2 1 5 4 1 PCI 라이저 2 확장 카드 커넥터 4 확장 카드 5 카드 에지 커넥터 3 확장 카드 래치 6 확장 카드에 모든 케이블을 연결하십시오 . 카드 케이블 연결에 대한 정보는 카드와 함께 제공된 설명서를 참조하십시오 . 7 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 확장 카드 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 전원 콘센트에서 시스템을 분리하십시 오. 2 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 3 카드에서 모든 케이블을 분리하십시오 . 4 확장 카드를 분리하십시오 . 64 a 확장 카드 래치를 여십시오 .
5 카드를 영구적으로 분리하는 경우 빈 확장 슬롯 입구에 금속 필러 브래킷을 설치한 다음 확장 카드 래치를 닫으십시오 . 주 : 시스템의 FCC(Federal Communications Commission) 인증을 유지하려면 필러 브래킷을 빈 확장 슬 롯에 설치해야 합니다 . 브래킷은 또한 시스템 안으로 먼지 및 이물질이 들어오는 것을 막고 시스템 내 부의 적절한 냉각 및 공기 흐름을 도와줍니다 . 6 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 부팅 장치 구성 하드 드라이브에서 시스템을 부팅하려면 드라이브를 주 ( 또는 부팅 ) 컨트롤러에 장착해야 합니다 . 시스템이 부팅되는 장치는 시스템 설치 프로그램에서 지정한 부팅 순서에 의해 결정됩니다 . 시스템 설치 프로그램에서는 시스템이 설치된 부팅 장치를 검색하는 데 사용하는 옵션을 제공합니 다 . 시스템 설치 프로그램에 대한 정보는 33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시오 .
일반 메모리 모듈 설치 지침 최적의 성능으로 시스템을 작동하려면 시스템 메모리를 구성할 때 다음 지침을 준수하십시오 . • 공인된 FBD만 사용하십시오. FBD는 단일 등급 또는 이중 등급일 수 있습니다. 1R로 표시된 FBD 는 단일 등급이고 2R 로 표시된 FBD 는 이중 등급입니다 . • 최소 2 개의 동일한 FBD 가 설치되어야 합니다 . • DIMM 소켓은 작은 숫자로부터 배치되어야 합니다 . • 메모리 모듈은 일치한 메모리 크기 , 속도 및 기술의 쌍으로 설치되어야 하며 구성된 메모리 모듈 의 총 개수는 총 2 개 , 4 개 또는 8 개여야 합니다 . 시스템의 최고의 성능을 유지하기 위해 모든 4 개 또는 8 개의 메모리 모듈은 모두 동일한 크기 , 속도 및 기술이어야 합니다 . • 메모리 스페어링 및 메모리 미러링은 8 개의 메모리가 필요하며 모든 메모리 모듈은 동일한 메 모리 크기 , 속도 및 기술이어야 합니다 .
표 3-1. 메모리 스페어링 구성 DIMM 크기 / 유형 메모리 총량 사용 가능한 여유 8 256MB 단일 등급 2GB 1GB 1GB 512MB 단일 등급 4GB 2GB 2GB 1GB 단일 등급 8GB 4GB 4GB 2GB 단일 등급 16GB 8GB 8GB 2GB 이중 등급 16GB 12GB 4GB 4GB 이중 등급 32GB 24GB 8GB 메모리 미러링 지원 시스템에 8 개의 동일한 메모리 모듈이 설치된 경우 시스템은 메모리 미러링을 지원합니다 . 미러링은 시스템 설치 프로그램에서 활성화되고 메모리 스페어링이 비활성화된 경우에만 사용할 수 있습니다 . (33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시오 .) 미러링된 구성에서 사용 가능한 시스템 메 모리 총량은 설치된 메모리의 절반입니다 . 메모리 모듈 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 .
그림 3-13. 메모리 모듈 설치 및 분리 1 2 3 1 메모리 모듈 2 메모리 모듈 이젝터 (2 개 ) 3 맞춤 키 6 메모리 모듈의 모서리 커넥터를 메모리 모듈 소켓의 맞춤 키에 맞추고 메모리 모듈을 소켓에 삽입 하십시오 . 주 : 메모리 모듈 소켓에는 메모리 모듈을 한 가지 방법으로만 소켓에 설치할 수 있게 하는 맞춤키가 있습니다 . 7 메모리 모듈을 소켓에 단단히 고정시키려면 집게 손가락으로 이젝터를 위로 당기면서 엄지 손가 락으로 메모리 모듈을 누르십시오 . 메모리 모듈이 소켓에 올비르게 장착된 경우 메모리 모듈 소켓의 이젝터는 메모리 모듈이 설치된 다른 소켓의 이젝터와 맞춰집니다 . 8 나머지 메모리 모듈을 설치하려면 이 절차의 단계3~단계7를 반복하십시오. 표 3-1을 참조하십시 오. 9 메모리 냉각 덮개를 장착하십시오 . 55 페이지 " 메모리 냉각 덮개 장착 " 을 참조하십시오 . 10 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 .
메모리 모듈 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 주의 : 시스템의 전원을 끈 후 메모리 모듈은 뜨거우므로 일정한 시간 동안 다치지 마십시오 . 메모리 모듈 을 다루기 전에 냉각될 때까지 기다리십시오 . 메모리 모듈을 다루는 경우 카드 모서리를 잡아야 하며 메모 리 모듈의 단자를 다치지 마십시오 . 1 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 2 메모리 냉각 덮개를 분리하십시오 . 54 페이지 " 메모리 냉각 덮개 분리 " 를 참조하십시오 . 3 메모리 모듈 소켓을 찾으십시오 . 그림 6-2 를 참조하십시오 . 4 메모리 모듈이 소켓에서 튕겨 나올 때까지 소켓 양쪽의 이젝터를 아래로 눌러 빼내십시오 . 그림 3-13 을 참조하십시오 .
4 메모리 냉각 덮개를 분리하십시오 . 54 페이지 " 메모리 냉각 덮개 분리 " 를 참조하십시오 . 주의사항 : 방열판을 분리할 경우 프로세서가 방열판에 부착되어 소켓에서 분리될 수도 있습니다 . 프로 세서의 열이 남아 있는 동안에 방열판을 분리하는 것이 좋습니다 . 주의사항 : 프로세서를 분리하지 않을 경우 , 프로세서에서 방열판을 절대로 분리하지 마십시오 . 방열판 은 온도를 알맞게 유지하는데 필요합니다 . 주의사항 : 프로세서와 방열판이 과열되어 매우 뜨거워질 수 있습니다 . 마이크로프로세서를 만지기 전에 열이 식을 때까지 충분히 기다리십시오 . 5 방열판 고정 레버 중 하나의 끝에 있는 청색 탭을 눌러 레버를 분리한 다음 해당 레버를 90 도 각으 로 들어 올리십시오 . 그림 3-14 를 참조하십시오 . 그림 3-14.
6 방열판가 프로세서에서 느슨해 질 때까지 30 초 정도 기다리십시오 . 7 다른 방열판 고정 레버를 여십시오 . 8 방열판이 프로세서에서 분리되지 않은 경우 방열판을 시계 방향으로 조심스럽게 회전한 다음 프 로세서에서 분리될 때까지 시계 반대 방향으로 돌리십시오 . 프로세서에서 방열판을 꺼내지 마십 시오 . 9 방열판을 프로세서에서 들어 꺼내고 열 그리스를 더럽히지 않도록 방열판을 뒤집어 놓으십시오 . 10 소켓 분리 레버를 90 도 각으로 위로 당겨 올려 소켓에서 프로세서를 분리하십시오 . 그림 3-15 를 참 조하십시오 . 11 프로세서 실드를 위로 회전하여 꺼내십시오 . 그림 3-15. 프로세서 설치 및 분리 3 4 5 2 1 6 1 소켓 키 (2) 2 프로세서 노치 3 프로세서 실드 4 프로세서 5 소켓 분리 레버 6 ZIF 소켓 12 프로세서 실드를 들어 프로세서를 분리한 다음 프로세서를 소켓에서 들어 빼내십시오 .
프로세서 설치 1 새 프로세서의 포장을 푸십시오 . 2 프로세서를 ZIF 소켓의 소켓 키에 맞추십시오 . 그림 3-15 를 참조하십시오 . 3 소켓에 프로세서를 설치하십시오 . 주의사항 : 프로세서를 잘못된 위치에 넣으면 시스템의 전원을 켤 때 시스템 보드 또는 프로세서가 영구 적으로 손상될 수 있습니다 . a 프로세서 소켓의 분리 레버를 완전히 위로 올리십시오 . b 프로세서 및 소켓 키를 맞춘 상태에서 프로세서를 소켓에 가볍게 장착하십시오 . 주의사항 : 프로세서를 장착할 때 강한 힘을 주지 마십시오 . 프로세서를 올바르게 놓은 경우 , 힘을 약간 만 가해도 프로세서가 소켓에 정확하게 끼워집니다 . c 프로세서가 소켓에 완전히 장착되면 프로세서를 고정하는 소켓 분리 레버가 제자리에 걸릴 때까지 아래쪽으로 다시 돌리십시오 . 그림 3-15 를 참조하십시오 . d 프로세서 실드를 닫으십시오 . 그림 3-15 를 참조하십시오 . 4 방열판을 설치하십시오 .
RAC 카드 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 선택 품목인 원격 액세스 컨트롤러 (RAC) 는 원격으로 서버를 관리할 수 있는 여러 가지 고급 기능을 제공합니다 . 다음 절차에서는 선택 품목인 RAC 카드를 설치 또는 분리하는 단계를 설명합니다 . RAC 카드 설치 1 주변 기기를 포함한 시스템 전원을 끈 후 전기 콘센트에서 시스템을 분리합니다 . 2 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 3 해당하는 경우 , 시스템 후면 패널에서 플라스틱 필러 플러그를 분리합니다 . 그림 3-16 을 참조하십 시오 . 4 가운데 라이저에 부착된 PCI 카드를 분리합니다 . 64 페이지 " 확장 카드 분리 " 를 참조하십시오 . 5 시스템 보드에서 중앙 라이저 카드를 분리하십시오 .
7 RAC 카드의 앞쪽 가장자리를 전면 플라스틱 고정 스탠드오프에 맞춘 후 안착될 때까지 카드 전면 을 아래로 누릅니다 . 그림 3-16 을 참조하십시오 . 카드 전면이 완전히 장착되면 전면 플라스틱 격리자가 카드의 전면 모서리에 걸립니다 . 8 "Planar"라고 적힌 커넥터가 해당 시스템 보드 커넥터에 연결되어 있고 "DRAC"라고 적힌 커넥터는 해당 RAC 카드 커넥터에 연결되어 있는지 확인하면서 두 개의 작은 케이블 (44 핀 케이블과 50 핀 케이블 ) 을 연결합니다 . 9 중앙 라이저 카드를 장착하십시오 . 83 페이지 " 확장 카드 라이저 " 를 참조하십시오 . 10 가운데 라이저에서 분리했던 PCI 카드를 다시 장착합니다. 63 페이지 "확장 카드 설치"를 참조하십 시오 . 11 시스템을 닫습니다 . 49 페이지 " 시스템 닫기 " 를 참조하십시오 . 12 시스템과 주변 기기를 전원에 다시 연결한 후 전원을 켭니다 .
광학 드라이브 전면 패널에 밀어 넣으며 측면판 보드를 통해 시스템 보드의 컨트롤러에 연결하는 트레이에 선택 사양 인 슬림라인 광학 드라이브가 장착됩니다 . 주 : DVD 장치는 데이타 전용입니다 . 광학 드라이브 트레이 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 해당 전원 콘센트에서 시스템을 분리하 십시오 . 2 베젤을 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 3 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 4 SAS 컨트롤러 보조 카드를 분리하십시오. 58 페이지 "SAS 컨트롤러 보조 카드 분리"를 참조하십시 오. 5 광학 드라이브 케이블을 드라이브 후면에서 분리하십시오 .
1 광학 드라이브 트레이 4 광학 드라이브 2 광학 드라이브 케이블 3 광학 드라이브 분리 탭 광학 드라이브 트레이 설치 1 광학 드라이브 트레이를 전면 패널의 해당 입구에 맞추십시오 . 광학 드라이브 입구는 SAS 보조 카드 베이의 바로 밑에 위치해 있습니다 . 2 드라이브 트레이가 제자리에 고정될 때까지 밀어 넣으십시오 . 그림 3-17 을 참조하십시오 . 3 광학 드라이브 케이블을 드라이브 후면에 연결하십시오 . 그림 3-17 을 참조하십시오 . 4 SAS 컨트롤러 보조 카드를 장착하십시오 . 58 페이지 "SAS 컨트롤러 보조 카드 또는 SAS RAID 컨 트롤러 보조 카드 설치 " 를 참조하십시오 . 5 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 6 베젤을 장착하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 7 시스템 및 주변 장치를 해당 전원 콘센트에 다시 연결하고 시스템을 켜십시오 .
주의사항 : 드라이브 포맷 중에 시스템을 종료하거나 재부팅하지 마십시오 . 이렇게 하면 드라이브 오류 가 발생할 수 있습니다 . 대용량 하드 드라이브를 포맷할 경우 포맷을 완료하려면 충분한 시간이 필요합니다 . 이러한 드라이브 에 대해 긴 포맷 시간은 정상입니다 . 예를 들면 9GB 하드 드라이브는 포맷하는 데 2.5 시간이 소요될 수 있습니다 . 드라이브 블랭크 분리 주의사항 : 적합한 시스템 온도를 유지하려면 모든 빈 하드 드라이브 베이에 하드 드라이브 블랭크를 설 치해야 합니다 . 하드 드라이브 캐리어를 시스템에서 분리하고 재설치하지 않은 경우 캐리어를 드라이브 블랭크로 교체해야 합니다 . 드라이브 블랭크 분리 절차는 해당 시스템이 3.5 인치 하드 드라이브로 구성되었는지 또는 2.5 인치 하드 드라이브로 구성되었는지에 의해 결정됩니다 . 3.5 인치 하드 드라이브 구성인 경우 : 1 전면 베젤이 장착되어 있으면 분리하십시오. 47 페이지 "전면 베젤 분리 및 장착"을 참조하십시오.
핫 플러그 하드 드라이브 설치 주의사항 : 하드 드라이브를 설치하는 경우 인접한 드라이브가 완전히 설치되어 있는지 확인하십시오 . 하드 드라이브 캐리어를 삽입하고 부분적으로 설치된 캐리어 옆에 해당 핸들을 잠그면 부분적으로 설치된 캐리어의 실드 스프링이 손상되고 사용하지 못할 수 있습니다 . 주의사항 : 일부 운영 체제는 핫 플러그 드라이브 설치를 지원하지 않습니다 . 운영 체제와 함께 제공된 설 명서를 참조하십시오 . 1 전면 베젤이 장착되어 있으면 분리하십시오. 47 페이지 "전면 베젤 분리 및 장착"을 참조하십시오. 2 드라이브 블랭크가 베이에 설치된 경우 분리하십시오 . 77 페이지 " 드라이브 블랭크 분리 " 를 참조 하십시오 . 3 핫 플러그 하드 드라이브를 설치하십시오 . a 하드 드라이브 캐리어 핸들을 여십시오 . 그림 3-18 을 참조하십시오 . 그림 3-18.
하드 드라이브 캐리어 장착 하드 드라이브 캐리어에서 하드 드라이브 분리 1 SATAu 드라이브 캐리어에서 SATA 하드 드라이브를 분리하는 경우 접속기 카드를 분리하십시오 . a 뒤면에서 하드 드라이브를 찾고 접속기 카드의 좌측 끝에서 분리 레버를 찾으십시오 . b 카드의 좌측 끝을 분리하려면 캐리어 레일에서 레버를 분리하여 꺼내십시오 . c 커넥터를 분리하려면 하드 드라이브에서 왼쪽 끝을 회전하여 꺼내십시오 . d 접속기 카드의 오른쪽 끝을 당겨 캐리어 레일의 슬롯에서 분리하십시오 . 2 하드 드라이브 캐리어의 슬라이드 레일에서 4 개의 나사를 분리하여 하드 드라이브를 캐리어에서 분리하십시오 . SATAu 드라이브 캐리어에 SAS 하드 드라이브 설치 주 : SAS 하드 드라이브는 SATAu 드라이브 캐리어에만 설치해야 합니다 . SATAu 드라이브 캐리어는 "SATAu" 로 표시되었으며 SAS 및 SATA 고정 나사를 표시하는 기호도 있습니다 .
그림 3-19. 드라이브 캐리어에 SAS 하드 드라이브 설치 2 1 3 1 나사 (4 개 ) 2 SATAu 드라이브 캐리어 3 SAS 하드 드라이브 SATA 드라이브 캐리어에 SATA 하드 드라이브 설치 주 : SAS 후면판에 직접 연결되는 SATA 하드 드라이브는 SATA 드라이브 캐리어 ("SATA" 로 표시됨 ) 에 설치 되어야 합니다 . 접속기 카드가 있는 SATA 하드 드라이브만 SATAu 드라이브 캐리어에 설치할 수 있습니다 . 1 드라이브 커넥터의 끝이 뒷부분에 놓이도록 SATA 하드 드라이브를 하드 드라이브 캐리어에 삽 입하십시오 . 그림 3-20 을 참조하십시오 . 2 하드 드라이브의 나사 구멍을 하드 드라이브 캐리어의 구멍에 맞추십시오 . 그림 3-20 을 참조하 십시오 . 3 4개의 나사를 장착하여 하드 드라이브를 하드 드라이브 캐리어에 고정하십시오. 그림3-20을 참 조하십시오 .
그림 3-20. SATA 드라이브 캐리어에 SATA 하드 드라이브 설치 2 1 3 1 나사 (4 개 ) 2 SATA 드라이브 캐리어 3 SATA 하드 드라이브 SATAu 하드 드라이브 캐리어에 SATA 하드 드라이브 및 접속기 카드 설치 주 : SATAu 드라이브 캐리어에 SATA 하드 드라이브를 설치하는 경우 하드 드라이브 후면에 삽입기 카드를 설치해야 합니다 . SATAu 드라이브 캐리어는 "SATAu" 로 표시되었으며 SAS 및 SATA 고정 나사를 표시하는 기호도 있습니다 . 1 드라이브 커넥터의 끝이 후면에 놓이도록 SATA 하드 드라이브를 SATAu 하드 드라이브 캐리어 에 삽입하십시오 . 그림 3-21 을 참조하십시오 . 2 그림 3-21 에서 표시된 조립품을 보고 하드 드라이브의 하단 후면 후면 나사 구멍을 하드 드라이 브 캐리어의 "SATAu" 라는 레이블이 붙은 구멍에 맞추십시오 .
4 삽입기 카드를 SATA 하드 드라이브의 뒷부분에 연결하십시오 . a 접속기 카드 브래킷의 탭이 캐리어 레일 내부의 슬롯에 연결되도록 접속기 카드의 상단을 캐 리어 레일 내부의 상단의 각도에 맞추십시오 . 그림 3-21 을 참조하십시오 . b 커넥터를 장착하려면 하드 드라이브를 향하여 카드의 하단 끝을 회전하십시오. 그림3-21을 참 조하십시오 . c 카드 브래킷의 래치가 제자리에 맞물릴 때까지 카드의 하단 끝을 하드 드라이브에 밀어 넣으 십시오 . 그림 3-21.
확장 카드 라이저 확장 카드 라이저 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 해당하는 경우 베젤을 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 2 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . 3 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 그림 3-22.
확장 카드 라이저 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 라이저 보드를 시스템 보드의 맞춤 핀에 맞춘 다음 보드를 핀에 내리십시오 . 2 보드의 에지 커넥터가 시스템 보드의 라이저 보드 커넥터에 완전히 장착될 때까지 라이저 보드를 누르십시오 . 그림 3-22 를 참조하십시오 . 3 해당하는 경우 확장 카드를 확장 카드 슬롯에 설치하십시오 . 4 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 5 베젤을 장착하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 6 시스템 및 주변 장치를 해당 전원 콘센트에 다시 연결하고 시스템을 켜십시오 .
그림 3-23. 2.
후면판 보드 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 후면판 보드를 장착하십시오 . – 3.5 인치 하드 드라이브 (2 개의 드라이브 ) 후면판을 설치하는 경우 보드를 고정 탭에 맞추고 보 드의 왼쪽 끝에 있는 분리 래치를 누른 다음 보드를 왼쪽으로 미십시오 . 그림 3-23 을 참조하 십시오 . – 2.5 인치 하드 드라이브 (4 개의 드라이브 ) 후면판을 설치하는 경우 보드를 드라이브 케이지 후 면의 고정 탭에 맞추고 후면판의 각 끝에 있는 분리 래치가 제자리에 걸릴 때까지 보드를 아래 로 미십시오 . 그림 6-4 를 참조하십시오 . 2 SAS 케이블 및 전원 케이블을 후면판 커넥터에 연결하십시오 . 3 하드 드라이브를 다시 설치하십시오 . 주 : 하드 드라이브를 분리되었던 동일한 드라이브 베이에 다시 설치하십시오 .
측면판 보드 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 측면판 보드의 끝에 있는 가이드를 시스템 보드의 핀에 맞추고 측면판 커넥터가 시스템 보드의 커 넥터에 완전히 장착될 때까지 측면판을 내리십시오 . 2 제어판 케이블 및 광학 드라이브 케이블 (해당하는 경우 )을 측면판에 연결하십시오 . 그림 6-8을 참 조하십시오 . 3 SAS 컨트롤러 보조 카드를 장착하십시오 . 58 페이지 "SAS 컨트롤러 보조 카드 또는 SAS RAID 컨 트롤러 보조 카드 설치 " 를 참조하십시오 . 4 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 5 베젤을 장착하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 .
그림 3-24. 시스템 전지 교체 2 1 3 전지 커넥터의 양극 쪽 1 2 시스템 전지 3 전지 커넥터의 음극 쪽 주의사항 : 전지 커넥터의 손상을 방지하려면 전지를 설치하거나 분리하는 경우 커넥터를 단단히 잡아야 합니다 . 6 새 시스템 전지를 설치하십시오 . a 커넥터의 양극 쪽을 단단히 눌러 전지 커넥터를 잡으십시오 . b "+" 가 위로 향하게 전지를 잡고 커넥터 양의 방향의 고정 탭 아래로 미십시오 . c 전지가 제위치에 고정될 때까지 전지를 수직으로 누르십시오 . 7 단계 3 에서 확장 카드를 분리한 경우 장착하십시오 . 63 페이지 " 확장 카드 설치 " 를 참조하십시오 . 8 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 9 시스템을 해당 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 모두 켜십시오 . 10 전지가 올바르게 작동하는지 확인하려면 시스템 설치 프로그램을 시작하십시오 .
1 해당하는 경우 베젤을 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 2 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . 3 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 4 SAS 컨트롤러 보조 카드를 분리하십시오. 58 페이지 "SAS 컨트롤러 보조 카드 분리"를 참조하십시 오. 5 제어판 보드 후면의 제어판 케이블을 분리하십시오 . 그림 3-25 를 참조하십시오 . 주의사항 : 커넥터를 분리할 때 케이블을 당기지 마십시오 . 이렇게 하면 케이블이 손상될 수 있습니다 . a 케이블 커넥터 끝의 금속 탭을 누르십시오 . b 커넥터를 조심스럽게 소켓에서 꺼내십시오 . 6 전면 패널 케이블을 제어판 보드에서 분리하십시오 . 그림 3-25 를 참조하십시오 . 7 제어판 캐리어 후면의 분리 탭을 들어 올리고 캐리어를 시스템의 후면을 향해 민 다음 캐리어를 들 어 시스템에서 빼내십시오 .
그림 3-25. 제어판 분리 및 설치 3 2 1 4 5 6 9 8 7 1 디스플레이 모듈 2 디스플레이 모듈 LCD 케이블 3 제어판 배선 보드 4 제어판 케이블 5 제어판 배선 보드 고정 나사 (3 개 ) 6 제어판 캐리어 분리 탭 7 제어판 캐리어 8 디스플레이 모듈 케이블 9 디스플레이 모듈 고정 나사 (2 개 ) 제어판 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 디스플레이 모듈을 섀시 차단기에 삽입하고 두 개의 나사로 고정하십시오 . 2 제어판 레이블을 디스플레이 모듈에 붙이십시오 . 3 캐리어에 제어판 보드를 설치하고 3 개의 십자 나사로 고정하십시오 . 그림 3-25 를 참조하십시오 . 4 캐리어를 시스템 섀시에 설치하십시오 .
8 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 9 시스템을 전원에 다시 연결하고 시스템 및 장착된 주변 장치를 켜십시오 . 10 해당하는 경우 베젤을 설치하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 시스템 보드 ( 서비스 전용 절차 ) 시스템 보드 분리 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 해당하는 경우 베젤을 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 2 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . 3 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 4 시스템 보드 후면 패널에서 모든 케이블을 분리하십시오 .
그림 3-26. 시스템 보드 분리 3 2 1 5 6 1 시스템 보드 트레이 분리 핸들 2 시스템 보드 트레이에 장착 된 시스템 보드 3 시스템 보드 분리 핀 4 시스템 보드 냉각 덮개 5 시스템 보드 고정 탭 6 시스템 보드 고정 슬롯 시스템 보드 설치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 트레이가 섀시의 하단에 평평하게 놓일 때까지 시스템 보드 트레이를 내리우십시오 . 2 모든 시스템 보드 고정 탭이 시스템 보드 고정 슬롯에 완전히 삽입되었는지 확인하십시오 . 그림 3-26 을 참조하십시오 . 3 시스템 보드 트레이가 제자리에 잠길 때까지 섀시의 후면을 향해 미십시오 . 4 해당하는 경우 RAC 카드를 장착하십시오 . 73 페이지 "RAC 카드 " 를 참조하십시오 .
9 모든 확장 카드를 장착하십시오 . 63 페이지 " 확장 카드 설치 " 를 참조하십시오 . 10 측면판 보드를 장착하십시오 . 87 페이지 " 측면판 보드 설치 " 를 참조하십시오 . 11 팬 모듈을 장착하십시오 . 51 페이지 " 냉각팬 모듈 장착 " 을 참조하십시오 . 12 메모리 냉각 덮개를 장착하십시오 . 55 페이지 " 메모리 냉각 덮개 장착 " 을 참조하십시오 . 13 전원 공급 장치를 장착하십시오 . 57 페이지 " 전원 공급 장치 장착 " 을 참조하십시오 . 14 시스템에 모든 케이블을 연결하십시오 . 15 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 16 베젤을 장착하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 를 참조하십시오 .
시스템 구성요소 설치
시스템 문제 해결 안전 제일 — 사용자와 시스템을 위하여 이 설명서의 절차를 수행하기 전에 시스템 덮개를 분리하고 시스템의 내부에서 작업해야 합니 다 . 시스템 내부에서 작업할 때 본 설명서 및 기타 설명서의 설명 없이 서비스를 수행하지 마십 시오 . 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니 다 . 절차를 수행하기 전에 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제 품 정보 안내를 참조하십시오 . 시작 루틴 시스템 시작 루틴 동안 Table 1-1 에서 설명한 지시사항에 대해 보고 들으십시오 . 표 4-1. 시작 루틴 표시 보기 / 듣기 내용 : 조치 전면 패널 LCD 에 표시된 상태 또는 오류 메시지 17 페이지 "LCD 상태 메시지 " 를 참조하십시오 . 모니터에 표시된 오류 메시지 25 페이지 " 시스템 메시지 " 를 참조하십시오 .
IRQ 지정 충돌 문제 해결 대부분 PCI 장치는 다른 장치와 함께 IRQ 를 공유할 수 있지만 동시에 하나의 IRQ 를 사용할 수는 없 습니다 . 이런 유형의 충돌을 피면하려면 각 PCI 장치의 개별 IRQ 요구를 참조하십시오 . 표 4-2 는 IRQ 지정을 나열합니다 . 표 4-2.
조치 1 모니터에 대한 시스템 및 전원 연결을 점검하십시오 . 2 비디오 출력 커넥터가 내장된 확장 카드가 시스템에 설치되었는지 확인하십시오 . 시스템 구성에서 일반적으로 모니터 케이블은 시스템 내장 비디오 커넥터가 아닌 확장 카드 커넥 터에 연결해야 합니다 . 모니터가 정확한 비디오 커넥터에 연결되었느지 확인하려면 시스템을 끄고 1 분 정도 기다린 다음 모니터를 다른 비디오 커넥터에 연결하고 시스템을 다시 켜십시오 . 3 전면 및 뒷면 비디오 커넥터에 연결된 모니터가 시스템에 설치되었는지 확인하십시오 . 시스템은 전면 또는 뒷면 비디오 커넥터에 연결된 모니터 하나만을 지원합니다 . 모니터가 전면 패 널에 연결된 경우 후면 패널 비디오 커넥터는 비활성화됩니다 . 시스템에 두 모니터가 연결된 경우 하나를 분리하십시오 문제가 해결되지 않으면 다음 단계를 계 속 진행하십시오 . 4 해당하는 온라인 진단 테스트를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참 조하십시오 .
마우스 문제 해결 문제 • 키보드에 문제가 발생했음을 나타내는 시스템 메시지가 표시됩니다 . • 마우스가 올바르게 작동하지 않습니다 . 조치 1 마우스 및 해당 케이블에 손상된 흔적이 있는지 확인하십시오 . 마우스가 손상되지 않은 경우 , 단계 4 로 이동하십시오 . 2 시스템 설치 프로그램을 실행하고 USB 포트가 활성화되었는지 확인하십시오 . 33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시오 . 마우스가 손상되면 다음 단계를 계속 진행하십시오 . 3 올바르게 작동하는 마우스로 결함이 있는 마우스를 교체해 보십시오 . 문제가 해결되면 결함이 있는 마우스를 교체하십시오 . 127 페이지 " 도움말 얻기 " 를 참조하십시 오. 4 문제가 해결되지 않은 경우 127 페이지 " 도움말 얻기 " 를 참조하십시오 . 5 해당 온라인 진단 검사를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조하십 시오 . 테스트가 실패하면 다음 단계를 계속 진행하십시오 .
직렬 I/O 장치 문제 해결 문제 • 직렬 포트에 연결된 장치가 올바르게 작동하지 않습니다 . 조치 1 직렬 포트에 연결된 시스템 및 모든 주변 장치를 끄십시오 . 2 올바르게 작동하는 케이블로 직렬 인터페이스 케이블을 교체하고 시스템 및 직렬 장치를 켜십시 오. 문제가 해결되면 인터페이스 케이블을 교체하십시오 . 3 시스템 및 직렬 장치를 끄고 유사한 장치로 교체하십시오 . 4 시스템 및 직렬 장치를 켜십시오 . 문제가 해결되면 직렬 장치를 교체하십시오 . 127 페이지 " 도움말 얻기 " 를 참조하십시오 . 문제가 지속되면 127 페이지 " 도움말 얻기 " 를 참조하십시오 . USB 장치 문제 해결 문제 • USB 장치에 문제가 발생했음을 나타내는 시스템 메시지가 표시됩니다 . • USB 포트에 연결된 장치가 올바르게 작동하지 않습니다 . 조치 1 시스템 설치 프로그램을 실행하고 USB 포트가 활성화되었는지 확인하십시오 .
NIC 문제 해결 문제 • NIC 가 네트워크와 통신할 수 없습니다 . 조치 1 해당하는 온라인 진단 테스트를 실행하십시오 . 113 페이지 " 시스템 진단 프로그램 실행 " 을 참조하 십시오 . 2 NIC 커넥터의 해당 표시등을 확인하십시오 16 페이지 "NIC 표시등 코드 " 를 참조하십시오 . • 연결 표시등이 켜지지 않는 경우 , 케이블 연결을 확인하십시오 . • 작동 표시등이 켜지지 않는 경우 , 네트워크 드라이버 파일이 손상되었거나 설치되지 않았을 수 있습니다 . 해당되는 경우 드라이버를 제거하고 재설치하십시오 . NIC 설명서를 참조하십시오 . • 가능한 경우 자동 감지 설정을 변경하십시오 . • 스위치 또는 허브에 다른 커넥터를 사용하십시오 . 내장형 NIC 카드가 아닌 NIC 카드를 사용하는 경우 NIC 카드의 설명서를 참조하십시오 . 3 올바른 드라이버가 설치되고 프로토콜이 연관되었는지 확인하십시오 . NIC 설명서를 참조하십시 오.
2 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 3 시스템에 설치된 모든 확장 카드를 분리하십시오 . 64 페이지 " 확장 카드 분리 " 를 참조하십시오 . 4 최소한 하루 정도 시스템을 건조시키십시오 . 5 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 6 시스템을 전기 콘센트에 다시 연결하고 시스템과 연결된 주변 장치를 켜십시오 . 시스템이 올바르게 시작하지 않으면 127 페이지 " 도움말 얻기 " 를 참조하십시오 . 7 시스템이 올바르게 시작되면 시스템을 끄고 분리한 모든 확장 카드를 재설치하십시오. 63 페이지 " 확장 카드 설치 " 를 참조하십시오 . 8 올바른 온라인 진단 테스트를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조 하십시오 . 검사가 실패하면 127 페이지 " 도움말 얻기 " 를 참조하십시오 . 손상된 시스템 문제 해결 문제 • 시스템을 떨어뜨렸거나 손상되었습니다 .
시스템 전지 문제 해결 문제 • 전지에 문제가 발생했음을 나타내는 시스템 메시지가 표시됩니다 . • 시스템 구성 정보가 시스템 설치 프로그램에서 유실되었습니다 . • 시스템 데이타 및 시간이 현재로 유지되지 않습니다 . 주 : 오래 동안 ( 몇 주 또는 몇 달 ) 시스템을 사용하지 않은 경우 NVRAM 의 시스템 구성 정보가 유실될 수 있습니다 . 이 문제는 불량 전지로 인해 발생합니다 . 조치 1 시스템 설치 프로그램에 시간 및 날짜를 재입력하십시오 . 33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시오 . 2 시스템을 끄고 최소 한시간 전원 콘센트에서 분리하십시오 . 3 시스템을 전원 콘센트에 다시 연결하고 시스템을 켜십시오 . 4 시스템 설치 프로그램을 시작하십시오 . 시스템 설치 프로그램의 시간 및 날짜가 정확하지 않는 경우 전지를 교체하십시오 . 87 페이지 " 시 스템 전지 " 를 참조하십시오 .
주의사항 : 전원 공급 장치를 핫 플러그할 수 있습니다 . 시스템이 작동하려면 하나의 전원 공급 장치 가 설치되어야 합니다 . 두 전원 공급 장치가 설치된 경우 시스템은 중복 모드로 작동합니다 . 분리하고 시 스템 전원이 켜졌을 때 하나의 전원 공급 장치만 설치되도록 하십시오 . 시스템이 전원 공급 장치 블랭크를 설치하지 않은 상태에서 하나의 전원 공급 장치로만 오랫동안 작동하는 경우 시스템이 과열될 수 있습니다 . 결함이 있는 전원 공급 장치를 분리하십시오 . 55 페이지 " 전원 공급 장치 " 를 참조하십시오 . 3 전원 공급 장치를 분리하고 다시 설치하여 제대로 설치되었는지 확인하십시오. 55 페이지 "전원 공 급 장치 " 를 참조하십시오 . 주 : 전원 공급 장치를 설치한 후 , 시스템에서 전원 공급 장치를 인식하고 올바르게 작동하는지 확인 하는 데 몇 초간의 시간이 소요됩니다 . 전원 공급 장치가 올바르게 작동할 경우 전원 표시등은 녹색으 로 표시됩니다 .
주의 : 냉각팬은 핫 플러그 가능하지 않습니다 . 시스템이 켜져 있는 동안 적합한 온도를 유지하려면 한번 에 하나의 팬만 교체하십시오 . 3 LCD 디스플레이 또는 진단 프로그램 소프트웨어에서 표시된 결함이 있는 팬을 찾으십시오 . 각 팬 의 식별 번호에 대해서는 51 페이지 " 냉각팬 분리 및 설치 " 를 참조하십시오 . 4 결함이 있는 팬의 전원 케이블이 팬 전원 커넥터에 단단히 연결되어 있는지 확인하십시오 . 50 페이 지 " 냉각팬 모듈 " 을 참조하십시오 . 주 : 시스템이 팬을 인식하고 올바르게 작동하는지 확인하려면 30 초 기다리십시오 . 5 문제가 해결되지 않으면 새 팬을 설치하십시오 . 50 페이지 " 냉각팬 모듈 " 을 참조하십시오 . 교체 팬이 올바르게 작동하면 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하 십시오 . 교체 팬이 작동하지 않으면 127 페이지 " 도움말 얻기 " 를 참조하십시오 .
8 메모리 냉각 덮개를 장착하십시오 . 55 페이지 " 메모리 냉각 덮개 장착 " 을 참조하십시오 . 9 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 10 시스템을 해당 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 켜십시오 . 11 시스템 설치 프로그램을 시작하고 시스템 메모리 설정을 확인하십시오. 33 페이지 "시스템 설치 프 로그램 사용 " 을 참조하십시오 . 설치된 메모리 총량이 시스템 메모리 설정과 일치하지 않으면 다음 단계를 수행하십시오 . a 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . b 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 주 : 메모리 모듈의 여러 구성이 존재합니다 . 66 페이지 " 일반 메모리 모듈 설치 지침 " 을 참조하십시 오. c 소켓 1 의 메모리를 동일한 용량의 다른 메모리로 교체하십시오 .
3 해당 온라인 진단 검사를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조하십 시오 . 4 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . 5 베젤을 열거나 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 6 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 7 인터페이스 케이블이 광학 드라이브와 측면판에 단단하게 연결되어 있는지 확인하십시오 . 8 해당하는 경우에 따라 SAS 컨트롤러 보조 카드 또는 SAS RAID 컨트롤러 보조 카드를 분리하십시 오 . 58 페이지 "SAS 컨트롤러 보조 카드 분리 " 를 참조하십시오 . 9 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 10 시스템을 전기 콘센트에 다시 연결하고 시스템과 연결된 주변 장치를 켜십시오 . 문제가 해결되지 않은 경우 127 페이지 " 도움말 얻기 " 를 참조하십시오 .
b 하드 드라이브가 RAID 에 올바르게 구성되었는지 확인하십시오 . c 구성 유틸리티를 종료하고 시스템을 운영 체제로 부팅하십시오 . 6 컨트롤러 보조 카드에 필요한 장치 드라이버가 설치되고 올바르게 구성되었는지 확인하십시오 . 자세한 내용은 운영 체제 설명서를 참조하십시오 . 주의사항 : SAS RAID 컨트롤러 보조 카드가 설치된 경우 다음 단계를 수행하지 마십시오 . 7 RAID 가 아닌 SAS 컨트롤러 보조 카드가 설치된 경우 하드 드라이브를 분리하고 해당 하드 드라이 브 베이 위치를 올바르게 작동하는 다른 하드 드라이브와 교환하십시오 . 문제가 해결되면 하드 드라이브를 원래 베이에 다시 설치하십시오 . 78 페이지 " 핫 플러그 하드 드 라이브 설치 " 를 참조하십시오 . 하드 드라이브가 원래 베이에서 제대로 작동하면 드라이브 캐리어에 간헐적으로 문제가 있을 수 있습니다 . 하드 드라이브 캐리어를 교체하십시오 . 127 페이지 " 도움말 얻기 " 를 참조하십시오 .
조치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 절차를 수행하기 전에 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 해당 온라인 진단 검사를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조하십 시오 . 2 시스템 설치 프로그램을 시작하고 SAS 또는 SAS RAID 컨트롤러 보조 카드가 활성화되었는지 확 인하십시오 . 33 페이지 " 시스템 설치 프로그램 사용 " 을 참조하십시오 . 3 시스템을 재시작하고 해당 키를 순차적으로 눌러 구성 유틸리티 프로그램을 시작하십시오 . • SAS 컨트롤러는 키를 누르십시오 . • SAS RAID 컨트롤러는 키를 누르십시오 . 구성 설정에 관한 정보는 컨트롤러 설명서를 참조하십시오 . 4 구성 설정을 확인하여 필요한 수정을 하고 시스템을 재시작하십시오 .
확장 카드 문제 해결 주 : 확장 카드의 문제를 해결하는 경우 운영 체제 및 확장 카드 설명서를 참조하십시오 . 문제 • 확장 카드에 문제가 발생했음을 나타내는 오류 메시지가 표시됩니다 . • 확장 카드가 올바르게 작동하지 않거나 작동하지 않습니다 조치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 절차를 수행하기 전에 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 해당 온라인 진단 검사를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조하십 시오 . 2 베젤을 열거나 분리하십시오 . 47 페이지 " 전면 베젤 분리 및 장착 " 을 참조하십시오 . 3 시스템과 연결된 주변 장치의 전원을 끄고 시스템을 전기 콘센트에서 분리하십시오 . 4 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 .
검사가 실패하면 127 페이지 " 도움말 얻기 " 를 참조하십시오 . 마이크로프로세서 문제 해결 문제 • 마이크로프로세서에 문제가 발생했음을 나타내는 오류 메시지가 표시됩니다 . • 프로세서 또는 시스템 보드에 문제가 발생했음을 나타내는 메시지가 전면 패널 상태 LCD 에 표시 됩니다 . • 각 프로세서에 방열판이 설치되지 않았습니다 . 조치 주의 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 절차를 수행하기 전에 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 해당 온라인 진단 테스트를 실행하십시오. 113 페이지 "서버 관리자 진단 프로그램 사용"을 참조하 십시오 . 2 시스템과 연결된 주변 장치의 전원을 끄고 시스템을 전기 콘센트에서 분리하십시오 . 3 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 .
16 프로세서 1을 동일한 용량의 다른 프로세서로 교체하십시오. 69 페이지 "프로세서 분리"를 참조하 십시오 . 17 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 18 해당 온라인 진단 검사를 실행하십시오 . 검사가 성공적으로 완료되는 경우 프로세서 2 를 교체하고 127 페이지 " 도움말 얻기 " 를 참조하 십시오 . 19 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리하십시오 . 20 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 21 단계 10 에서 분리한 프로세서를 재설치하십시오 . 69 페이지 " 프로세서 분리 " 를 참조하십시오 . 22 시스템을 닫으십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 23 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 켜십시오 . 문제가 지속되면 127 페이지 " 도움말 얻기 " 를 참조하십시오 .
시스템 문제 해결
시스템 진단 프로그램 실행 시스템에 문제가 발생하면 기술 지원에 문의하기 전에 진단 프로그램을 실행하십시오 . 진단 프로 그램은 추가 장비가 필요없이 데이타를 유실하지 않고 시스템 하드웨어를 점검할 수 있습니다 . 자 체로 문제를 해결할 수 없는 경우 서비스 및 지원 직원은 진단 프로그램 점검 결과를 사용하여 문제 를 해결할 수 있습니다 . 서버 관리자 진단 프로그램 사용 시스템 문제에 액세스하려면 우선 온라인 서버 관리자 진단 프로그램을 사용하십시오 . 문제를 식 별할 수 없는 경우에 시스템 진단 프로그램을 사용하십시오 . 온라인 진단 프로그램에 액세스하려면 서버 관리자 홈 페이지에 로그인한 다음 진단 프로그램 탭 을 클릭하십시오 . 진단 프로그램 사용에 관한 정보는 온라인 도움말을 참조하십시오 . 추가 정보는 서버 관리자 사용 설명서를 참조하십시오 . 시스템 진단 프로그램 기능 진단 프로그램은 개별 장치 그룹 또는 장치의 일련의 메뉴 및 옵션을 제공합니다 .
시스템 진단 프로그램 실행 하드 드라이브의 유틸리티 파티션에서 시스템 진단 프로그램을 실행합니다 . 주의사항 : 시스템 진단 프로그램은 해당 시스템을 테스트하는 데만 사용하십시오 . 이 프로그램을 다른 시스템에 사용하면 유효하지 않은 결과 또는 오류 메시가 표시될 수 있습니다 . 또한 , 시스템과 함께 제공 된 프로그램만 사용하십시오 ( 또는 해당 프로그램의 업데이트 버전 ). 1 시스템이 부팅될 때 POST 중에 키를 누르십시오 . 2 유틸리티 파티션 주 메뉴에서 시스템 진단 프로그램 실행을 선택하거나 메모리 문제를 해결할 경 우 메모리 진단 프로그램을 선택하십시오 . 시스템 진단 프로그램을 시작할 경우 진단 프로그램이 초기화되고 있음을 나타내는 메시지가 표시됩니 다 . 다음 , Diagnostics 메뉴가 나타납니다 . 이 메뉴를 사용하여 모든 특정 진단 테스트를 실행하거나 시 스템 진단 프로그램을 종료할 수 있습니다 .
진단 프로그램 옵션 선택 원하는 장치 검사 방법을 선택하려면 Diagnostics Options 영역을 사용하십시오 . 다음 옵션을 설치할 수 있습니다 . • Non-Interactive Tests Only — 검사할 때 사용자 개입이 필요하지 않은 검사만 실행합니다 . • Quick Tests Only — 검사할 때 장치의 빠른 검사만 실행합니다 . 이 옵션을 선택할 경우 확장된 검 사는 실행되지 않습니다 . • Show Ending Timestamp — 검사할 때 검사 로그에 시간을 표시합니다 . • Test Iterations — 검사를 실행할 횟수를 선택합니다 . • Log output file pathname — 검사할 때 검사 로그 파일을 저장할지 여부를 지정할 수 있도록 합니 다. 내용 및 결과 보기 Customize 창의 탭은 검사 및 검사 결과에 대한 정보를 제공합니다 . 다음 탭은 사용 가능합니다 . • Results — 실행된 검사 및 결과를 표시합니다 .
시스템 진단 프로그램 실행
점퍼 및 커넥터 본 항목에서는 시스템 점퍼에 대한 자세한 정보를 제공합니다 . 또한 점퍼 및 스위치에 대한 기 본 정보를 제공하며 시스템의 다양한 보드에 있는 커넥터에 대해 설명합니다 . 시스템 보드 점퍼 그림 6-1 는 시스템 보드에서 시스템 구성 점퍼의 위치를 표시합니다 . 표 6-1 는 점퍼 설정을 나 열합니다 . 주 : 점퍼에 액세스하려면 분리 래치를 들고 덮개를 시스템의 전면을 향하여 밀어 시스템 보드 냉각 덮 개를 분리하십시오 . 그림 3-13 을 참조하십시오 . 주 : 점퍼에 쉽게 액세스하도록 메모리 모듈 공기 흐름판을 들어 올리십시오 .
그림 6-1. 시스템 보드 점퍼 표 6-1. 시스템 보드 점퍼 설정 점퍼 1 PWRD_EN 설정 설명 ( 기본값 ) 암호 기능이 활성화됩니다 . 암호 기능이 비활성화됩니다 . 2 NVRAM_CLR ( 기본값 ) 구성 설정이 시스템 부팅 시 유지됩니다 . 구성 설정이 다음 시스템 부팅 시 지워집니다 . ( 구성 설정이 시스템이 부팅하지 않는 점에서 손상되면 점퍼 를 설치하고 시스템을 부팅하십시오 . 구성 정보를 복 원하기 전에 점퍼를 분리하십시오 .) 주 : 본 표에 사용된 약어 및 머리글자의 전체 이름에 관한 내용은 149 페이지 " 용어집 " 을 참조하십시 오.
잊은 암호 비활성화 시스템의 소프트웨어 보안 기능에는 33 페이지 " 시스템 설치 프로그램 사용 " 에 자세히 설명되어 있는 시스템 암호 및 설치 암호가 포함되어 있습니다 . 암호 점퍼는 이러한 암호 기능을 활성화하거나 비활성 화하며 현재 사용 중인 임의 암호를 지웁니다 . 주의사항 : 제품 정보 안내에서 안전 지침의 " 정전기 방전 방지 " 를 참조하십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 전원 콘센트에서 시스템을 분리하십시 오. 2 시스템을 여십시오 . 48 페이지 " 시스템 열기 및 닫기 " 를 참조하십시오 . 3 메모리 모듈 덮개를 들어 올리십시오 . 4 암호 점퍼에서 점퍼 플러그를 분리하십시오 . 시스템 보드에 암호 점퍼를 위치 지정하는 데 관한 정보는 그림 6-1 을 참조하십시오 . 5 시스템을 닫으십시오 . 6 시스템 및 주변 장치를 해당 전원 콘센트에 다시 연결하고 시스템을 켜십시오 .
시스템 보드 커넥터 시스템 보드 커넥터의 위치 및 설명에 관한 내용은 그림 6-2 및 표 6-2 를 참조하십시오 . 그림 6-2.
표 6-2.
SAS/SATA 후면판 보드 커넥터 그림 6-3 은 두 개의 3.5 인치 하드 드라이브 ( 옵션 1) 를 지원하는 SAS/SATA 후면판 보드의 커넥터 위치 를 보여줍니다 . 그림 6-3. SAS 3.5 인치 드라이브 후면판 보드 구성요소 - 옵션 1 1 1 후면판 전원 커넥터 4 드라이브 1 커넥터 3 2 2 드라이브 0 커넥터 4 3 SAS A 커넥터 그림 6-4 및 그림 6-5 는 4 개의 2.5 인치 하드 드라이브 ( 옵션 2) 를 지원하는 SAS/SATA 후면판 보드의 커넥터 위치를 보여줍니다 .
그림 6-4. SAS 2.5 인치 드라이브 후면판 보드 구성요소 - 옵션 2( 전면 ) 6 5 4 3 7 2 1 1 드라이브 1 커넥터 2 드라이브 0 커넥터 3 드라이브 3 커넥터 4 드라이브 2 커넥터 5 고정 탭 6 고정 슬롯 7 분리 래치 (2 개 ) 그림 6-5.
확장 카드 라이저 보드 구성요소 및 PCI 버스 이 시스템에는 두 개의 확장 카드 구성이 있습니다 . 각 라이저 ( 중앙 라이저 및 좌측 라이저 ) 에는 PCI-X 구성이나 PCIe 구성용으로 하나의 슬롯이 포함됩니다 . 본 시스템은 두 라이저에 대해 하나의 구성 (PCI-X 또는 PCIe) 만 지원합니다 . 그림 6-6 및 그림 6-7 은 확장 카드 슬롯 및 버스를 포함한 선 택 사양인 PCI-X 확장 카드 라이저 보드의 구성요소를 보여줍니다 . 62 페이지 "PCIe 라이저 보드 확 장 슬롯 " 및 63 페이지 "PCI-X 라이저 보드 확장 슬롯 " 은 PCI 버스 및 각 확장 카드 슬롯의 작동 속도 를 나열합니다 . 주 : 방향 및 물리적 커넥터가 비슷하기 때문에 PCIe 확장 카드 구성은 표시하지 않습니다 . 그림 6-6. 선택 사양인 PCI-X 확장 카드 좌측 라이저 보드 구성요소 2 1 시스템 보드 커넥터 1 그림 6-7.
SAS 측면판 보드 커넥터 그림 6-8.
점퍼 및 커넥터
도움말 얻기 기술 지원 기술 문제에 대한 지원이 필요하면 다음 단계를 수행하십시오 . 1 95 페이지 " 시스템 문제 해결 " 의 절차를 완료하십시오 . 2 시스템 진단 프로그램을 실행하고 제공된 모든 절차를 기록하십시오 . 3 진단 점검사항의 사본을 만들어 작성하십시오 . 4 설치 및 문제 해결 절차에 대한 도움말은 Dell 지원 (support.dell.com) 에 있는 Dell 의 다양한 온 라인 서비스를 사용하십시오 . 자세한 내용은 127 페이지 " 온라인 서비스 " 를 참조하십시오 . 5 이 단계를 수행해도 문제가 해결되지 않으면 Dell 사에 문의하십시오 . 주 : 기술 지원부에 전화로 문의하는 경우 필요한 절차를 수행할 수 있도록 시스템 옆이나 가까운 곳에 서 전화하십시오 . 주 : Dell 특급 서비스 코드 시스템은 일부 국가에서 지원되지 않을 수 있습니다 . Dell 의 자동 응답 전화 시스템에서 프롬프트가 표시되면 특급 서비스 코드를 입력하여 해당 지원 담당자와 직접 연결하십시오 .
www.euro.dell.com( 유럽 전용 ) www.dell.com/la/ ( 라틴 아메리카 국가 전용 ) www.dell.ca( 캐나다 전용 ) • 익명 FTP( 파일 전송 프로토콜 ) ftp.dell.com/ user:anonymous 로 로그인한 다음 사용자의 전자 우편 주소를 암호로 사용하십시오 . • 전자 지원 서비스 support@us.dell.com apsupport@dell.com( 아시아 / 태평양 지역 국가 전용 ) support.jp.dell.com( 일본 전용 ) support.euro.dell.com( 유럽 전용 ) • 전자 시세 정보 서비스 apmarketing@dell.com( 아시아 / 태평양 지역 국가 전용 ) sales_canada@dell.com( 캐나다 전용 ) AutoTech 서비스 Dell 의 자동 응답 기술 지원 서비스인 AutoTech 는 Dell 고객이 휴대용과 데스크탑용 컴퓨터 시스템에 관해 자주 질문하는 사항을 응답기를 통해 제공합니다 .
Dell Enterprise Training and Certification 이제 Dell Enterprise Training and Certification 을 사용할 수 있습니다 . 자세한 내용은 www.dell.com/training 을 참조하십시오 . 일부 지역에서는 이 서비스가 제공되지 않습니다 . 주문 관련 문제 부품의 누락 및 결함 , 또는 잘못된 청구서 발송과 같은 주문상의 문제가 발생하는 경우에는 Dell 고객 지원부로 문의하십시오 . 문의할 때에는 제품 구매서나 포장재를 준비하십시오 . 해당 지역의 연락처 정 보를 참조하십시오 . 제품 정보 Dell 에서 추가로 구입할 수 있는 제품에 대한 정보가 필요하거나 제품을 주문하려면 Dell 웹 사이트 (www.dell.com) 를 방문하십시오 . 영업 담당자와 통화하려면 해당 지역의 연락처 정보를 참조하십시오 . 수리 또는 신용 보증에 따른 제품 반환 수리 또는 신용 보증에 따라 제품을 반환하는 경우 , 다음 사항을 준비하십시오 .
문의하기 전에 주 : 전화를 걸어 문의하기 전에 특급 서비스 코드를 알아두십시오 . Dell 자동 응답 지원 전화 시스템은 이 코드를 사용하여 보다 효율적으로 고객의 전화 문의를 처리합니다 . 진단 점검사항에 기록해 두는 것을 잊지 마십시오 . 가능하면 Dell 사에 기술 지원을 문의하기 전에 시스 템을 켜고 가까운 곳에서 전화를 거십시오 . 문의 중에 키보드에서 몇 가지 명령을 입력하거나 작업 중 의 세부 정보를 중계하거나 컴퓨터 시스템 자체적인 문제 해결 절차를 수행해야 할 수 있습니다 . 시스 템 설명서가 있는지 확인하십시오 . 주의 : 컴퓨터 내부의 임의의 구성요소를 수리하기 전에 , 중요한 안전 정보에 대해서는 제품 정보 안내를 참조하십시오 .
진단 점검사항 이름 : 날짜 : 주소 : 연락처 : 서비스 태그 ( 컴퓨터 후면의 바코드 ): 특급 서비스 코드 : 제품 반환 승인 번호 (Dell 지원 기술자가 알려준 경우 ): 운영 체제 및 버전 : 주변 장치 : 확장 카드 : 네트워크에 연결되어 있습니까 ? 예 아니오 네트워크 , 버전 , 네트워크 카드 : 프로그램 및 버전 : 시스템의 시작 파일 내용을 확인하려면 운영 체제 설명서를 참조하십시오 . 가능한 경우 각 파일을 인쇄하십시오 . 프린터가 연결되어 있지 않으면 Dell 사에 문의하기 전에 각 파 일의 내용을 기록해 두십시오 .
Dell 사에 문의하기 인터넷으로 Dell 에 접속하려면 다음 웹 사이트를 이용하십시오 . • www.dell.com • support.dell.com( 기술 지원 ) 국가별 웹 주소는 아래 표에 나와있는 해당 지역을 찾아 보십시오 . 주 : 수신자 부담 번호는 목록에 명시되어 있는 국가에서만 사용할 수 있습니다 . 주 : 일부 국가에서 Dell XPS™ 휴대용 컴퓨터의 특정 기술 지원은 유관 국가를 위해 별도로 제공된 전화 번 호를 사용하여 문의할 수 있습니다 . XPS 휴대용 컴퓨터에 대해 별도로 제공된 전화 번호를 찾을 수 없는 경 우에는 제공된 지원 번호를 사용하여 Dell 사에 문의할 수 있으며 사용자의 전화는 해당 부서로 연결됩니다 . Dell 에 문의하려면 다음 표에 나와 있는 전화 번호 , 코드 , 전자 우편 주소를 사용하십시오 . 사용할 코드를 확인하려면 지역 또는 국제 교환원에게 문의하십시오 .
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 오스트리아 ( 비엔나 ) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 900 전자 우편 : tech_support_central_europe@dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 브루나이 기술 지원 ( 말레이시아 페낭 ) 604 633 4966 국가 코드 : 673 고객 관리 ( 말레이시아 페낭 ) 604 633 4888 일반 판매 ( 말레이시아 페낭 ) 604 633 4955 캐나다 ( 온타리오 주 요크 북부 ) 온라인 주문 상태 : www.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 중국 ( 하문 ) 기술 지원 웹 사이트 : support.dell.com.cn 국가 코드 : 86 기술 지원 전자 우편 : cn_support@dell.com 도시 코드 : 592 고객 관리 전자 우편 : customer_cn@dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 체코 ( 프라하 ) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 전자 우편 : czech_dell@dell.com 국가 코드 : 420 기술 지원 22537 2727 고객 관리 22537 2707 팩스 번호 22537 2714 기술 팩스 번호 22537 2728 교환대 22537 2711 덴마크 ( 코펜하겐 ) 웹 사이트 : support.euro.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 프랑스 ( 파리 )( 몽펠리에 ) 웹 사이트 : support.euro.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 그리스 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 기술 지원 00800-44 14 95 18 국가 코드 : 30 특별 서비스 기술 지원 00800-44 14 00 83 교환대 2108129810 특별 서비스 교환대 2108129811 판매 2108129800 팩스 번호 2108129812 그레나다 대표 지원부 수신자 부담 번호 : 1-866-540-3355 과테말라 대표 지원부 1-800-999-0136 가이아나 대표 지원부 수신자 부담 번호 : 1-877-270-4609 홍콩 웹 사이트 : support.ap.dell.com 국제 접속 코드 : 001 기술 지원 전자 우편 : HK_support@Dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 아일랜드 ( 체리우드 ) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 전자 우편 : dell_direct_support@dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 일본 ( 가와사키 ) 웹 사이트 : support.jp.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 라틴 아메리카 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 고객 기술 지원 ( 미국 텍사스 주 오스틴 ) 512 728-4093 고객 서비스 ( 미국 텍사스 주 오스틴 ) 512 728-3619 팩스 번호 ( 기술 지원 및 고객 서비스 )( 미국 텍 사스 주 오스틴 ) 512 728-3883 판매 ( 미국 텍사스 주 오스틴 ) 512 728-4397 SalesFax( 미국 텍사스 주 오스틴 ) 512 728-4600 또는 512 728-3772 룩셈부르크 웹 사이트 : support.euro.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 멕시코 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 고객 기술 지원 001-877-384-8979 또는 001-877-269-3383 국제 접속 코드 : 00 국가 코드 : 52 지역 코드 , 지역 번호 , 수신자 부담 번호 판매 50-81-8800 또는 01-800-888-3355 고객 서비스 001-877-384-8979 또는 001-877-269-3383 기본 50-81-8800 또는 01-800-888-3355 몬세라트 대표 지원부 수신자 부담 번호 : 1-866-278-6822 네덜란드 안틸레스 대표 지원부 001-800-882-1519 네덜란드 ( 암스테르담 ) 웹 사이트 : support.euro.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 노르웨이 (Lysaker) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 XPS 휴대용 컴퓨터 전용 기술 지원 815 35 043 국가 코드 : 47 기타 모든 Dell 컴퓨터 기술 지원 671 16882 관련 고객 관리 671 17575 가정 / 중소기업체 고객 관리 23162298 교환대 671 16800 팩스 교환대 671 16865 파나마 대표 지원부 001-800-507-0962 페루 대표 지원부 0800-50-669 폴란드 ( 바르샤바 ) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 011 전자 우편 : pl_support_tech@dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 싱가폴 ( 싱가폴 ) 웹 사이트 : support.ap.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 스페인 ( 마드리드 ) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 가정 및 중소기업체 국가 코드 : 34 기술 지원 902 100 130 도시 코드 : 91 고객 관리 902 118 540 판매 902 118 541 교환대 902 118 541 팩스 번호 902 118 539 기업체 기술 지원 902 100 130 고객 관리 902 115 236 교환대 91 722 92 00 팩스 번호 91 722 95 83 스웨덴 (Upplands Vasby) 웹 사이트 : support.euro.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 대만 웹 사이트 : support.ap.dell.com 국제 접속 코드 : 002 전자 우편 : ap_support@dell.com 국가 코드 : 886 기술 지원 (OptiPlex, Latitude, Inspiron, Dimension 및 Electronics, 보조 프로그램 ) 수신자 부담 번호 : 00801 86 1011 기술 지원(PowerApp, PowerEdge, PowerConnect 및 PowerVault) 수신자 부담 번호 : 00801 60 1256 고객 관리 수신자 부담 번호 : 00801 60 1250 ( 옵션 5) 일반 판매 수신자 부담 번호 : 00801 65 1228 기업체 판매 수신자 부담 번호 : 00801 651 227 태국 웹 사이트 : support.ap.dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 영국 (Bracknell) 웹 사이트 : support.euro.dell.com 국제 접속 코드 : 00 고객 관리 웹 사이트 : support.euro.dell.com/uk/en/ECare/Form/Home.asp 국가 코드 : 44 도시 코드 : 1344 우루과이 지역 코드 , 지역 번호 , 수신자 부담 번호 전자 우편 : dell_direct_support@dell.
국가 ( 도시 ) 국제 접속 코드 국가 코드 도시 코드 부서명 또는 서비스 분야 , 웹 사이트 및 전자 우편 주소 지역 코드 , 지역 번호 , 수신자 부담 번호 미국 ( 텍사스 주 오스틴 ) 자동 주문 현황 서비스 수신자 부담 번호 : 1-800-433-9014 국제 접속 코드 : 011 AutoTech( 휴대용 및 데스크탑 컴퓨터 ) 수신자 부담 번호 : 1-800-247-9362 국가 코드 : 1 관련 고객을 위한 하드웨어 및 기술 지원 (Dell TV, 프린터 및 프로젝터 ) 수신자 부담 번호 : 1-877-459-7298 고객 ( 가정 및 사무실 ) 모든 기타 Dell 제품을 위한 기술 지원 수신자 부담 번호 : 1-800-624-9896 고객 서비스 수신자 부담 번호 : 1-800-624-9897 EPP( 직원 구매 프로그램 ) 고객 수신자 부담 번호 : 1-800-695-8133 재무 서비스 웹 사이트 : www.dellfinancialservices.
용어집 이 절에서는 시스템 설명서에 사용된 기술 용어 , 약어 및 머리글자에 대해 설명합니다 . DDR — 더블 데이타 속도 (Double-data rate). 출력을 잠 재적으로 배로 늘리는 메모리 모듈 기술입니다 . A — 암페어 (Ampere). DHCP — 동적 호스트 구성 프로토콜 (Dynamic Host Configuration Protocol). 클라이언트 시스템에 IP 주소 를 자동으로 할당하는 방식입니다 . AC — 교류 전류 (Alternating current). ACPI — 고급 구성 및 전원 인터페이스 (Advanced Configuration and Power Interface). 운영 체제가 구성 및 전원을 관리할 수 있도록 하는 표준 인터페이스입니다 . ANSI — 미 국립 표준국 (American National Standards Institute). 미국의 기술 표준을 개발하는 주요 기관입니 다.
ESM — 내장된 서버 관리 (Embedded server management). IP — 인터넷 프로토콜 (Internet Protocol). expansion card — 시스템 보드의 확장 카드 커넥터에 꽂 는 NIC 또는 SCSI 어댑터와 같은 추가 카드입니다 . 확 장 카드는 확장 버스와 주변장치 간에 인터페이스를 제 공하여 시스템에 특정 기능을 추가합니다 . expansion-card connector — 확장 카드에 연결하는 컴퓨 터의 시스템 보드나 라이저 보드의 커넥터입니다 . IRQ — 인터럽트 요청 (Interrupt request). 주변장치를 이용하여 IRQ 회선을 통해 프로세서로 데이터를 전송 하거나 수신할지 알리는 신호입니다 . 각 주변장치를 연 결하려면 IRQ 번호를 지정해야 합니다 . 두 개의 장치가 같은 IRQ 할당값을 공유할 수 있지만 동시에 사용할 수 는 없습니다 . F — 화씨 (Fahrenheit). K — 킬로 (Kilo). 1000.
local bus — 로컬 버스 확장 기능이 있는 시스템의 경우, 일부 주변장치 ( 예를 들면 , 비디오 어댑터 회로 ) 를 기 존의 확장 버스와 실행될 때보다 빠른 속도로 실행할 수 있습니다 . 버스를 참조하십시오 . NVRAM — 비휘발성 임의 접근 메모리 (Nonvolatile random-access memory). 시스템을 꺼도 메모리의 내용 이 유실되지 않습니다 . NVRAM 은 날짜 , 시간 및 시스 템 구성 정보를 기억하는 데 사용됩니다 . LVD — 저전압차 (Low voltage differential). PCI — 주변장치 구성요소 상호 연결 (Peripheral Component Interconnect). 로컬 버스를 구현하는 표준 입니다 . m — 미터 (Meter). mA — 밀리암페어 (Milliampere). MAC 주소 — 매체 액세스 제어 주소 (Media Access Control address). 네트워크상에서 시스템의 고유 하드 웨어 번호입니다 .
ROMB — 마더보드에 있는 RAID(RAID on motherboard). rpm — 분당 회전수 (Revolutions per minute). RTC — 실시간 클럭 (Real-time clock). SAS — 직렬 연결된 SCSI. SATA — 시리얼 고급 기술 부착 (Serial Advanced Technology Attachment). 시스템 보드와 저장 장치 간의 표준 인터페이스입니다 . SCSI — 소형 컴퓨터 시스템 인터페이스 (Small computer system interface). 표준 포트보다 더 빠른 데이 타 전송 속도를 제공하는 I/O 버스 인터페이스입니다 . UNIX — 범용 인터넷 교환 (Universal Internet Exchange). UNIX 는 Linux 의 근간을 이루며 C 프로그 래밍 언어로 구성된 운영 체제입니다 . UPS — 무정전 전원 공급 장치 (Uninterruptible power supply).
Windows Server 2003 — XML Web 서비스를 사용하여 소프트웨어를 통합할 수 있는 Microsoft 소프트웨어 기 술 세트입니다 . XML Web 서비스는 XML 로 작성된 작 고 재활용이 가능한 응용프로그램으로써 , 연결되지 않 은 원본 간의 데이타 통신을 가능하게 합니다 . XML — 확장형 생성 언어 (Extensible Markup Language). XML 은 일반적인 정보 형식을 만들고 월드 와이드 웹 , 인트라넷 등을 통해 형식 및 데이타를 공유 하는 방법입니다 . ZIF — 0 삽입력 (Zero insertion force). 가딩 — 데이타 저장용 물리 드라이브 여러 개와 하나의 패리티 데이타 저장용 추가 드라이브를 사용한 일종의 데이타 중복 방법입니다 . 미러링 , 스트라이핑 및 RAID 를 참조하십시오 . 구성요소 — 구성요소는 DMI 와 관련되어 있으며 구성 요소에는 운영 체제 , 컴퓨터 시스템 , 확장 카드 및 DMI 와 호환되는 주변장치가 포함됩니다 .
블레이드 — 프로세서 , 메모리 및 하드 드라이브가 포 함된 모듈입니다 . 모듈은 전원 공급 장치와 팬이 있는 섀시에 장착되어 있습니다 . 시리얼 포트 — 모뎀을 시스템에 연결할 때 주로 사용하 는 I/O 포트입니다 . 시스템의 직렬 포트는 대개 9 핀 커 넥터로 구성되어 있습니다 . 비디오 드라이버 — 그래픽 모드 응용프로그램과 운영 체제에서 선택한 해상도에서 지정된 색상을 사용하여 화면에 표시할 수 있도록 사용하는 프로그램입니다 . 비 디오 드라이버는 시스템에 설치되어 있는 비디오 어댑 터와 일치해야 합니다 . 시스템 구성 정보 — 메모리에 저장된 데이타로서 설치 되어 있는 하드웨어 종류와 시스템을 올바르게 구성하 는 방법을 시스템에 나타냅니다 . 비디오 메모리 — 대부분의 VGA 와 SVGA 비디오 어댑 터에는 시스템의 RAM 과 메모리 칩이 들어 있습니다 .
점퍼 — 회로 보드에서 돌출된 2 개 이상의 핀에 끼워진 작은 블록입니다 . 배선과 연결된 플라스틱 플러그를 핀 위에 끼워 넣습니다 . 배선은 핀을 연결하고 회로를 작 성하며 보드의 회로를 변경할 수 있는 단순하고 전환 가 능한 방법을 제공합니다 . 플래쉬 메모리 — 시스템에 설치되어 있는 상태에서 디 스켓의 유틸리티를 사용하여 다시 프로그래밍할 수 있 는 일종의 EEPROM 칩입니다 . 대부분의 EEPROM 칩 은 특수 프로그래밍 장치를 사용해야만 재기록할 수 있 습니다 . 제어판 — 전원 단추 및 전원 표시등과 같은 표시등과 제어부가 있는 시스템의 일부분입니다 . 픽셀 — 비디오 디스플레이상의 단일 점입니다 . 픽셀은 행과 열로 정렬되어 이미지를 만듭니다 . 비디오 해상도 는 640 x 480과 같이 수평 방향 픽셀과 수직 방향의 픽셀 수로 표시합니다 . 종료 — SCSI 케이블 양끝에 있는 장치 같은 일부 장치 는 케이블에서 반사와 유사 신호의 변경을 막기 위해 종 료되어야 합니다 .
용어집
색인 B P BMC, 43 BMC, 43 PCI 버스 확장 카드 라이저 보드 , 124 C CD 드라이브 문제 해결 , 105 D Dell 문의하기 , 131-132 DIMM 메모리 모듈 , 65 소켓 , 65 POST 시스템 기능에 액세스 중 , 10 R RAC 카드 설치 , 73 RAID 전지 분리 , 62 설치 , 61 raid 전지 , 61 RAID 전지 설치 , 61 RAID 컨트롤러 ( 내장형 ) 문제 해결 , 107 I IRQ 라인 지정 , 96 충돌 피면 , 96 N NIC 문제 해결 , 100 표시등 , 16 커넥터 , 122 SATA 하드 드라이브 , 76 후면판 , 122 SATA 후면판 보드 커넥터 , 122 U USB 장치 문제 해결 , 99 Z ZIF 소켓 , 69 ㄱ 경고 메시지 , 30-31 S SAS RAID 전지 , 61 측면판 보드 커넥터 , 125 하드 드라이브 , 76 후면판 , 122 SAS 컨트롤러 보조 카드 분리 , 58 SAS 하드 드
색인 메모리 , 66 부팅 드라이브 , 65 설치 , 77 기능 전면 패널 , 11 드라이브 캐리어 SAS 하드 드라이브 (SATAu), 79 SATA 하드 드라이브 (SATA), 80 SATA 하드 드라이브 (SATAu), 81 ㄴ 디스켓 드라이브 광학 / 디스켓 드라이브 트레 이를 참조하십시오 .
장착 , 48 ㅅ 보조 카드 SAS, 58 서비스 전용 프로세서 , 69 부팅 드라이브 구성 , 65 서비스 전용 절차 시스템 보드 , 91 제어판 조립품 , 88 부팅 장치 구성 , 65 분리 RAID 전지 , 62 SAS 컨트롤러 보조 카드 , 58 광학 / 디스켓 드라이브 트레 이 , 75 냉각팬 모듈 , 50 덮개 , 48 드라이브 캐리어에서 드라이 브 분리 , 79 라이저 , 83 메모리 , 69 베젤 , 47 시스템 보드 , 91 전원 공급 장치 , 56 전원 공급 장치 블랭크 , 58 전지 , 87 제어판 조립품 , 88 측면판 보드 , 84 하드 드라이브 블랭크 , 77 분리 및 장착 베젤 , 48 블랭크 전원 공급 장치 , 58 하드 드라이브 , 77 비디오 문제 해결 , 96 선택 사양인 라이저 분리 , 83 설명서 필요한 , 9 설치 , 70 RAC 카드 , 73 SAS 컨트롤러 보조 카드 , 58 SAS/SATA 하드 드라이브 , 78 SATA 드라이브 캐리어의 SATA
색인 완전 버퍼된 DIMM 메모리 모듈 , 65 직렬 I/O 장치 문제 해결 , 99 시스템 설치 프로그램 사용 , 33 외장형 장치 연결 , 15 시스템 설치 프로그램 화면 기본 , 34 내장형 장치 , 38 시스템 보안 , 39 외장형 장치 연결 , 15 진단 사용 시기 , 113 테스트 옵션 , 114 시스템 암호 변경 , 42 사용 , 40 삭제 , 42 지정 , 40 ㅈ 진단 프로그램 고급 검사 옵션 , 114 장착 냉각팬 모듈 , 51 전원 공급 장치 , 57 전지 , 87 프로세서 , 69 ㅊ 시작 , 33 옵션 , 34 진단 메시지 , 31 참조 설명서 , 9 전면 패널 기능 , 11 측면판 보드 , 84 분리 , 84 설치 , 86 전원 표시등 , 15 측면판 보드 커넥터 , 125 ㅋ ㅇ 전원 공급 장치 문제 해결 , 102 분리 , 56 장착 , 57 안전 , 95 전원 공급 장치 블랭크 , 58 암호 비활성화 , 119 설치 ,
전면 패널 , 11 전원 , 15 하드 드라이브 , 12 후면 패널 , 14 프로세서 교체 , 69 설치 , 71 업그레이드 , 69 장착 , 69 커넥터 , 124 활성화된 설치 암호 작동 , 42 후면 패널 기능 , 14 필요한 정보 , 9 ㅎ 하드 드라이브 SAS 하드 드라이브 , 76 SATA 드라이브 캐리어에 SATA 설치 , 80 SATA 하드 드라이브 , 76 SATAu 드라이브 캐리어에 SAS 설치 , 79 SATAu 드라이브 캐리어에 SATA 설치 , 81 드라이브 캐리어에서 분리 , 79 부팅 장치 , 65 표시등 코드 , 12 확장 슬롯 PCI 버스 , 124 확장 카드 PCIe, 62 PCI-X, 62 문제 해결 , 109 분리 , 83 설치 , 63 설치 지침 , 63 확장 카드 라이저 보드 PCI 버스 , 124 색인 161
색인 162 색인