Dell™ PowerEdge™ 1950 Systems Information Update
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. ©2006–2009 Dell Inc. All rights reserved.
Contents Non-Optimal Memory Configurations . . . . . . . . . . . 5 . . . . . . . 5 . . . . . . . . . . . . . 5 PowerEdge 1950 III – New System Features New Performance Features New High-Efficiency Power Supply and Power Monitoring Features . . . . . . . . . . . 5 . . . . . . . . . . . 6 . . . . . . . . . . . . . . . 6 New I/O and Storage Features . New Security Features . Optional Internal USB Memory Key . . . . . . . . . . . . 6 . . 8 . . . . . . . . . .
System Setup Program Update. Memory Screen . . . . . . . . . . . . . . 21 . . . . . . . . . . . . . . . . . . 21 . . . . . . . . . . . . . . 22 CPU Information Screen Integrated Devices Screen . System Security Screen . . . . . . . . . . . . 22 . . . . . . . . . . . . . . 23 Operating System Information . Enumeration of NICs . . . . . . . . . . . . . 25 . . . . . . . . . . . . . . . . 25 RHEL – Incorrect Processor Information . . . . . . 25 . . . 25 . . . . . . . . . . 26 . . . . .
Non-Optimal Memory Configurations The POST may halt when a non-optimal memory configuration is detected and the following message is displayed: Non-Optimal Memory Configuration Press F1 to continue or F2 for Setup NOTE: Mixing DIMMs of different speeds renders the memory configuration non6Hoptimal. The system clocks down the performance to the slowest speed in the DIMM set for the channel.
New I/O and Storage Features • Optional Intel quad-port Gigabit Ethernet NIC, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps data rates and iSCSI remote boot. • Support for 10-Gb Ethernet cards. • One internal USB 2.0-compliant connector supporting an optional bootable USB flash drive or USB memory key. • Support for optional SAS 6i/R and PERC 6/i adapters. New Security Features • Trusted Program Module (TPM) support for improved security. • Optional support for iSCSI boot.
Figure 1-1. Internal USB Connector Location 1 2 1 system board 2 internal USB connector location To boot from the USB memory key, you must configure the USB memory key with a boot image and then specify the USB memory key in the boot sequence in the System Setup program. See "Using the System Setup Program" in the Hardware Owner’s Manual. For information on creating a bootable file on the USB memory key, see the user documentation that accompanied the USB memory key.
Installing the Optional Internal USB Memory Key WARNING: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet. 2 Open the system.
5 Replace the memory cooling shroud. 6 Close the system. See "Closing the System" in the Hardware Owner’s Manual. 7 Reconnect the system to power and restart the system. 8 Enter the System Setup program and verify that the USB key has been detected by the system. See "Using the System Setup Program" in the Hardware Owner’s Manual.
System Board Replacement – Safeguarding Encrypted Data On PowerEdge 1950 III systems using Windows Server® 2008, you can use encryption programs, such as the BitLocker utility, to secure the contents of the hard drive. If you are using the TPM with an encryption application, you are prompted to create a recovery key during system setup. Be sure to store this recovery key.
Table 1-1. System Messages Message Causes Corrective Actions Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving. The memory configuration does not support node interleaving, or the configuration has changed (for example, a failed DIMM) so that node interleaving cannot be supported. The system runs but with reduced functionality. Ensure that the memory modules are installed in a configuration that supports node interleaving.
Table 1-1. System Messages (continued) Message Causes Corrective Actions PCI BIOS failed to install PCIe device BIOS (Option Reseat the expansion ROM) checksum failure card(s). Ensure that all detected during shadowing. appropriate cables are Cables to expansion card(s) securely connected to the loose; faulty or improperly expansion card(s). If the installed expansion card(s). problem persists, see "Troubleshooting System Expansion Cards" in the Hardware Owner’s Manual.
Table 1-1. System Messages (continued) Message Causes Corrective Actions PCIe Training Error: Integrated device The specified PCIe device is faulty or improperly installed. For a SAS controller daughter card, reseat the card in the dedicated PCIe connector. See "Installing a SAS Controller Daughter Card" in the Hardware Owner’s Manual. If the problem persists, see "Getting Help" in the Hardware Owner’s Manual.
Table 1-1. System Messages (continued) Message Causes TPM operation is Configuration change has pending. Press I to been requested. Ignore or M to Modify to allow this change and reset the system. WARNING: Modifying could prevent security. Warning: Following faulty DIMMs are disabled: DIMM n1 n2 Total memory size is reduced. Corrective Actions Press I to continue system boot. Press M to modify the TPM setting and restart. Faulty or improperly seated See "Troubleshooting memory module(s).
Table 1-1. System Messages (continued) Message Causes Corrective Actions Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site. Invalid memory configuration. The system runs but with reduced functionality. Ensure that the memory modules are installed in a valid configuration. See "General Memory Module Installation Guidelines" in the Hardware Owner’s Manual.
Table 1-2. LCD Status Messages Code Text Causes Corrective Actions N/A SYSTEM NAME A 62-character string that can be defined by the user in the System Setup program. This message is for information only. You can change the system ID and name in the System The SYSTEM NAME Setup program. See is displayed under "Using the System the following Setup Program" in conditions: the Hardware Owner’s Manual. • The system is powered on. • The power is off and active errors are displayed.
Table 1-2. LCD Status Messages (continued) Code Text Causes Corrective Actions E1625 PS AC Current Power source is out Check the AC of acceptable range. power source. E1711 PCI PERR B## D## F## The system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus ##, device ##, function ##. Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting an Expansion Card" in the Hardware Owner’s Manual.
Table 1-2. LCD Status Messages (continued) Code Text Causes Corrective Actions E1712 PCI SERR B## D## F## The system BIOS has reported a PCI system error on a component that resides in PCI configuration space at bus ##, device ##, function ##. Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards" in the Hardware Owner’s Manual. PCI SERR Slot # The system BIOS has reported a PCI system error on a component that resides in the specified slot.
Table 1-2. LCD Status Messages (continued) Code Text Causes Corrective Actions E171F PCIE Fatal Err The system BIOS B## D## F## has reported a PCIe fatal error on a component that resides in PCIe configuration space at bus ##, device ##, function ##. Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards" in the Hardware Owner’s Manual.
Table 1-2. LCD Status Messages (continued) Code Text E2110 MBE DIMM # & # One of the two indicated DIMMs has had a memory multi-bit error (MBE). See "Troubleshooting System Memory" in the Hardware Owner’s Manual. E2111 SBE Log The system BIOS Disable DIMM # has disabled memory single-bit error (SBE) logging, and does not resume logging further SBEs until the system is restarted. "#" represents the DIMM implicated by the BIOS. See "Troubleshooting System Memory" in the Hardware Owner’s Manual.
System Setup Program Update Memory Screen Table 1-3 lists the descriptions for the information fields that appear on the Memory Information screen. Table 1-3. Memory Information Screen Options Option Description System Memory Size Displays the amount of system memory. System Memory Type Displays the type of system memory. System Memory Speed Displays the system memory speed. Video Memory Displays the amount of video memory.
CPU Information Screen Table 1-4 updates the description for the Demand-Based Power Management option. Table 1-4. CPU Information Screen Option Description Demand-Based Power Management (Enabled default) NOTE: Check your operating system documentation to verify if the operating system supports this feature. Enables or disables demand-based power management.
Table 1-5. Integrated Devices Screen Options (continued) Option Description I/OAT DMA Enables or disables the I/O Acceleration Technology (I/OAT) Engine option. When set to Enabled, I/OAT reduces system CPU (Disabled default) usage for applications that use TCP by offloading part of TCP receive operation to the DMA engine. System Interrupts This field controls the interrupt assignment for PCI devices Assignment in the system.
Table 1-6. New System Security Screen Options (continued) Option Description TPM Activation Changes the operational state of the TPM. When set to Activate, the TPM is enabled and activated at default settings. When set to Deactivate, the TPM is disabled and deactivated. The No Change state initiates no action. The operational state of the TPM remains unchanged (all user settings for the TPM are preserved). NOTE: This field is read-only when TPM Security is set to Off.
Operating System Information Enumeration of NICs Linux operating system versions that use the udev kernel device manager enumerate the NICs differently than earlier Linux versions that used the devfs device manager.
Hardware Owner’s Manual Updates Installing the Processor When installing the processor, the processor shield must be closed before securing the processor with the socket release lever. System Diagnostics Custom Test Options In the Customize window of the system diagnostics, the Log output file pathname option enables you to specify the diskette drive or USB memory key where the test log file is saved. You cannot save the file to a hard drive.
Dell™ PowerEdge™ 1950 系统 信息更新
注、小心和警告 注:“注”表示可以帮助您更好地使用计算机的重要信息。 小心:“小心”表示如果不遵循说明,就有可能损坏硬件或 导致数据丢失。 警告: “警告”表示可能会造成财产损失、人身伤害甚至死亡。 ____________________ 本说明文件中的信息如有更改,恕不另行通知。 © 2006 – 2009 Dell Inc. 版权所有,翻印必究。 未经 Dell Inc. 书面许可,严禁以任何形式复制这些材料。 本文中使用的商标:Dell、 DELL 徽标和 PowerEdge 是 Dell Inc. 的商标; Intel 和 Xeon 是 Intel Corporation 的注册商标; Microsoft、Windows 和 Windows Server 是 Microsoft Corporation 在美 国和 / 或其它国家 / 地区的商标或注册商标; Red Hat 和 Red Hat Enterprise Linux 是 Red Hat, Inc. 的注册商标; SUSE 是 Novell Inc.
目录 非优化的内存配置 . . . . . . . . . . . . . . . . . . . PowerEdge 1950 III – 全新系统功能 全新性能 . . . . . . . . . . . 31 . . . . . . . . . . . . . . . . . . . . . 31 全新高效电源设备和电源监测功能 . . . . . . . 31 . . . . . . . . . . . . . . . 31 . . . . . . . . . . . . . . . . 32 全新 I/O 和存储功能 . 全新安全保护功能 可选的内部 USB 存储钥匙 . . . . . . . . . . . . . . . 安装可选的内部 USB 存储钥匙 . . . . . . . . . 支持 8 GB 内存模块 – PowerEdge 1950 III 系统 . 32 33 . . . 35 . . . . . . . . . . 35 . . . . . . . . . . . . . 35 . . . . . . . . . .
系统设置程序更新 内存屏幕 . . . . . . . . . . . . . . . . . . . 45 . . . . . . . . . . . . . . . . . . . . . . 45 CPU Information (CPU 信息)屏幕 . . . . . . . Integrated Devices (集成设备)屏幕 . . . . . . System Security (系统安全保护)屏幕 . 操作系统信息 枚举 NIC 47 . . . . . . . . . . . . . . . . . . . . . . 49 . . . . . . . . . . . . . . . . . . . . . . 49 . . . . . . . . . . . . Microsoft Windows 2000 的系统支持 . 安装处理器 . 49 . . . . . . 49 . . . . . . . . . . . . . . . . 50 . . . . . . . . . . . . . . . . . . . .
非优化的内存配置 当系统检测到非优化的内存配置,POST 可能会中止,并显示以下 信息时: Non-Optimal Memory Configuration (非优化的内存配置) Press F1 to continue or F2 for Setup (按 F1 继续,按 F2 进行设置) 注:混合使用不同速度的 DIMM 会导致内存配置非优化。系统会将性能降 低到通道的 DIMM 集中最慢的速度。 PowerEdge 1950 III – 全新系统功能 全新性能 • 两个双核或四核 Intel® Xeon® 5400 系列和 5300 系列处理器。 • 8 GB 内存模块支持。 全新高效电源设备和电源监测功能 • 在不同的工作负载之间进行功率转换,以使系统效率更高。 • 底板管理控制器 (BMC) 电源监测可监测电流、电压以及系统中的电源 使用。 全新 I/O 和存储功能 • 可选 Intel 四端口千兆位以太网 NIC,可支持 10 Mbps、100 Mbps 和 1000 Mbps 数据速率以及 iSCSI 远程引导。 • 支持 10 Gb 以太网卡。 • 一个内部 USB
全新安全保护功能 • 受信任的平台模块 (TPM),支持增强的安全保护级别。 • 支持 iSCSI 引导(可选)。 可选的内部 USB 存储钥匙 PowerEdge 1950 III 系统提供了一个位于系统板上的内部 USB 连接器,可配 合 USB 快擦写存储钥匙使用 (请参阅图 1-1)。 USB 存储钥匙可用作引导 设备、安全保护密钥或大容量存储设备。要使用内部 USB 连接器,必须启 用系统设置程序的 Integrated Devices (集成设备)屏幕中的 Internal USB Port (内部 USB 端口)选项。请参阅第 46 页上的 “Integrated Devices (集成设备)屏幕”。 图 1-1.
要从 USB 存储钥匙引导,必须为 USB 存储钥匙配置一个引导映像,然后在 系统设置程序的引导顺序中指定 USB 存储钥匙。请参阅《硬件用户手册》 中的“使用系统设置程序”。有关在 USB 存储钥匙上创建可引导文件的 信息,请参阅 USB 存储钥匙随附的用户说明文件。 注:必须使用钥匙制造商提供的格式化公用程序对包含多个 LUN(逻辑单元 号码)的 USB 钥匙进行格式化。 注:为了避免与系统内部的组件相冲突,USB 钥匙不能超出以下规格上限: 11.68 毫米厚(0.46 英寸)x 24.89 毫米宽(0.98 英寸)x 66.8 毫米长 (2.
图 1-2.
支持 8 GB 内存模块 – PowerEdge 1950 III 系统 PowerEdge 1950 III 系统添加了对以下经过许可的 8 GB 内存配置的支持: • 64 GB — 8 x 8 GB 四排内存模块 • 48 GB — 4 x 8 GB 四排和 4 x 4 GB 双排内存模块 如果安装了 64 GB 的内存,则在 POST 期间,系统仅识别并显示 63.
系统信息更新 表 1-1 列出 PowerEdge 1950 III 系统新的系统信息、出现这些信息的可能原 因以及纠正措施。 警告: 只有经过培训的维修技术人员才能卸下系统护盖并拆装系统的任何 内部组件。有关安全预防措施、拆装计算机内部组件以及防止静电释放的完 整信息,请参阅 《产品信息指南》。 表 1-1. 系统信息 信息 原因 Alert!Node Interleaving disabled! Memory configuration does not support Node Interleaving.
表 1-1.
表 1-1.
表 1-1. 系统信息 (续) 信息 原因 纠正措施 TPM configuration operation honored. (TPM 配置操作已 执行。) 系统会立即重设。 仅供参考。 TPM Failure (TPM 故障) 受信任的平台模块 (TPM) 功能出现故障。 请参阅《硬件用户手册》 中的“获得帮助”。 TPM operation is 请求更改配置。 pending.Press I to Ignore or M to Modify to allow this change and reset the system.WARNING: Modifying could prevent security.
表 1-1. 系统信息 (续) 信息 原因 纠正措施 Warning! No micro 微代码更新失败。 code update loaded for processor n (警告!未载入处理器 n 的微代码更新) 请更新 BIOS 固件。请参阅 《硬件用户手册》中的 “获得帮助”。 Warning: The 内存配置无效。系统会 installed memory 继续运行,但功能有所 configuration is 降低。 not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site.
LCD 状态信息更新 表 1-2 列出可能出现在 PowerEdge 1950 III 系统中的 LCD 状态信息的更新, 以及每条信息的可能原因。LCD 信息引用系统事件日志 (SEL) 中记录的 事件。有关 SEL 和配置系统管理设置的信息,请参阅系统管理软件说明 文件。 表 1-2.
表 1-2.
表 1-2.
表 1-2.
系统设置程序更新 内存屏幕 表 1-3 列出了 Memory Information(内存信息)屏幕上显示的信息字段的 说明。 表 1-3.
CPU Information(CPU 信息)屏幕 表 1-4 更新针对 Demand-Based Power Management(基于需求的电源管理) 选项的说明。 表 1-4. CPU Information(CPU 信息)屏幕 选项 说明 Demand-Based Power Management(基于需求的 电源管理) (默认设置为 Enabled [ 已启用 ]) 注:请查看您的操作系统说明文件,验证操作系统是 否支持此功能。 启用或禁用基于需求的电源管理。启用时,会向操作系 统报告 CPU 性能状态表;禁用时,则不向操作系统报 告 CPU 性能状态表。如果任何 CPU 不支持基于需求的 电源管理,该字段会变为只读字段,并自动设置为 Disabled(已禁用)。 Integrated Devices(集成设备)屏幕 表 1-5 列出新的 Integrated Devices(集成设备)屏幕选项。 表 1-5.
表 1-5.
表 1-6.
操作系统信息 枚举 NIC 与使用 devfs 设备管理器的早期 Linux 版本相比,使用 udev 内核设备管理器 的 Linux 操作系统版本枚举 NIC 的方式不同。尽管这不会影响系统功能, 但使用 Red Hat® Enterprise Linux®(版本 4 或版本 5)或 SUSE® Linux Enterprise Server 9 或 10 操作系统时,枚举 NIC 的方式完全相反:NIC1 被 配置为 eth1,而不是 eth0 ; NIC2 被配置为 eth0,而不是 eth1。有关如何 更改默认设备枚举的信息,请参阅位于 linux.dell.
《硬件用户手册》更新 安装处理器 安装处理器时,在使用插槽释放拉杆固定处理器之前,必须合上处理器 护盖。 系统诊断程序自定义检测选项 在系统诊断程序的 Customize(自定义)窗口中,Log output file pathname (日志输出文件路径名)选项允许您指定用于保存检测日志文件的软盘驱动 器或 USB 存储钥匙。您不能将文件保存在硬盘驱动器上。 50 信息更新
Systèmes Dell™ PowerEdge™ 1950 Mise à jour des informations
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque de dommage matériel ou de perte de données en cas de non-respect des instructions données. AVERTISSEMENT : Un AVERTISSEMENT vous avertit d'un risque d'endommagement du matériel, de blessure corporelle ou de mort.
Table des matières . . . . . . . 55 Nouvelles fonctionnalités des systèmes PowerEdge 1950 III. . . . . . . . . . . . . . . . . . . . 55 Nouvelles fonctions d'optimisation des performances . . . . . . . . . . . . . . . . . 55 Configurations de mémoire non optimales Nouvelles fonctionnalités haute efficacité pour l'alimentation et le contrôle de l'alimentation . . . . . . . . . . . . . . . . . . 55 . . . . . 56 . . . . . . . . . . 56 . . . . . . . .
Mise à jour du programme de configuration du système . . . . . . . . . . . . . . . . . . Écran relatif à la mémoire . . . . . . 73 . . . . . . . . . . . . . 73 Écran CPU Information (Informations sur le processeur) . . . . . . . . . . 75 . . . . . . . . . . . . . 75 . . . . . . . . . . . . . . . 77 Écran Integrated Devices (Périphériques intégrés) . Écran System Security (Sécurité du système) . Informations concernant le système d'exploitation. Énumération des NIC . . 79 . . . . . . . . . .
Configurations de mémoire non optimales Lorsqu'une configuration de mémoire non optimale est détectée, le système peut interrompre le POST et afficher le message suivant : Non-Optimal Memory Configuration (Configuration de mémoire non optimale) Press F1 to continue or F2 for Setup (Appuyez sur F1 pour poursuivre ou sur F2 pour accéder au menu de configuration) REMARQUE : l'utilisation de barrettes DIMM de cadences différentes rend la configuration de la mémoire non optimale.
Nouvelles fonctions d'E/S et de stockage • Carte NIC Ethernet Gigabit Intel en option (quatre ports) prenant en charge des débits de 10, 100 et 1000 Mbps, ainsi que l'amorçage iSCSI à distance • Prise en charge des cartes Ethernet 10 Go • Connecteur USB interne compatible 2.
Figure 1-1. Emplacement du connecteur USB interne 1 2 1 Carte système 2 Emplacement du connecteur USB interne Pour pouvoir démarrer le système à partir d'une clé de mémoire USB, vous devez configurer celle-ci avec une image d'amorçage et la spécifier dans la séquence d'amorçage définie dans le programme de configuration du système. Voir “Utilisation du programme de configuration du système” dans le document Manuel du propriétaire.
Installation de la clé de mémoire USB interne en option AVERTISSEMENT : Seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Voir le document Guide d'information sur le produit pour obtenir des informations détaillées sur les consignes de sécurité, les interventions dans l'ordinateur et la protection contre les décharges électrostatiques.
5 Réinstallez le carénage de refroidissement de la mémoire. 6 Refermez le système. Voir “Fermeture du système” dans le document Manuel du propriétaire. 7 Rebranchez le système sur la prise secteur et redémarrez-le. 8 Accédez au programme de configuration du système et vérifiez que la clé USB a été détectée. Voir “Utilisation du programme de configuration du système” dans le document Manuel du propriétaire.
Mises à niveau du processeur pour les systèmes PowerEdge 1950 II et III • Si la mention “II” figure à l'avant du châssis, le système peut être mis à niveau via l'installation de processeurs Intel Xeon double cœur de la série 5100, ou de processeurs Intel Xeon quadruple cœur de la série 5300.
Mise à jour des messages système Le tableau 1-1 répertorie les nouveaux messages système du PowerEdge 1950 III. Il indique également leur cause probable, ainsi que les mesures correctives appropriées. AVERTISSEMENT : Seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
Tableau 1-1. Messages système (suite) Message Causes Actions correctives Invalid PCIe card found in the Internal_Storage slot! Le système s'est arrêté, car une carte d'extension PCIe non valide est installée dans l'emplacement dédié au contrôleur de stockage. Retirez la carte d'extension PCIe installée dans l'emplacement réservé et remplacez-la par le contrôleur SAS.
Tableau 1-1. Messages système (suite) Message Causes Actions correctives PCIe Degraded Link Width Error: Integrated device Le périphérique PCIe indiqué est défectueux ou mal installé. Pour une carte contrôleur fille SAS, remboîtez la carte dans le connecteur PCIe approprié. Voir “Installation d'une carte contrôleur fille SAS” dans le document Manuel du propriétaire. Si l'incident persiste, voir “Obtention d'aide” dans le document Manuel du propriétaire.
Tableau 1-1. Messages système (suite) Message Causes Actions correctives PCIe Training Error: Slot n Carte PCIe défectueuse ou mal installée dans le support spécifié. Réinstallez la carte PCIe dans le logement indiqué. Voir “Cartes d'extension” dans le document Manuel du propriétaire. Si l'incident persiste, voir “Obtention d'aide” dans le document Manuel du propriétaire. Remote Access Controller cable error or incorrect card in the RAC slot.
Tableau 1-1. Messages système (suite) Message Causes Actions correctives Warning: Following faulty DIMMs are disabled: Modules de mémoire défectueux ou mal installés. Les barrettes DIMM sont désactivées deux par deux, comme indiqué par n1 et n2. Vérifiez les deux barrettes DIMM pour détecter une panne éventuelle. Voir “Dépannage de la mémoire système” dans le document Manuel du propriétaire.
Tableau 1-1. Messages système (suite) Message Causes Actions correctives Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site. Configuration de mémoire non valide. Le système fonctionne mais de façon restreinte. Assurez-vous que la configuration des modules de mémoire est valide.
Mise à jour concernant les messages d'état affichés sur l'écran LCD Le tableau 1-2 répertorie les nouveaux messages d'état qui peuvent s'afficher sur l'écran LCD du système PowerEdge 1950 III. Il indique également leur cause probable. Les messages de l'écran LCD se rapportent aux éléments enregistrés dans le journal d'événements du système. Pour plus d'informations sur ce journal et sur la configuration des paramètres de gestion du système, voir la documentation du logiciel de gestion de systèmes.
Tableau 1-2. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Actions correctives E1118 CPU Temp Interface Le contrôleur BMC ne parvient pas à déterminer la température des processeurs. Il augmente donc la vitesse des ventilateurs correspondants, par mesure de précaution. Éteignez le système et redémarrez-le. Si l'incident persiste, voir “Obtention d'aide” dans le document Manuel du propriétaire.
Tableau 1-2. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Actions correctives E1711 PCI PERR B## D## F## Le BIOS du système a renvoyé une erreur de parité PCI liée à un composant résidant dans l'espace de configuration PCI du bus ##, périphérique ##, fonction ##. Retirez les cartes d'extension PCIe et remboîtez-les dans leur connecteur. Si l'incident persiste, voir “Dépannage des cartes d'extension” dans le document Manuel du propriétaire.
Tableau 1-2. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Actions correctives E1712 PCI SERR B## D## F## Le BIOS du système a renvoyé une erreur de parité PCI liée à un composant résidant dans l'espace de configuration PCI du bus ##, périphérique ##, fonction ##. Retirez les cartes d'extension PCIe et remboîtez-les dans leur connecteur. Si l'incident persiste, voir “Dépannage des cartes d'extension” dans le document Manuel du propriétaire.
Tableau 1-2. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Actions correctives E171F PCIE Fatal Err Le BIOS du système a B## D## F## renvoyé une erreur de parité PCIe liée à un composant résidant dans l'espace de configuration PCIe du bus ##, périphérique ##, fonction ##. Retirez les cartes d'extension PCIe et remboîtez-les dans leur connecteur. Si l'incident persiste, voir “Dépannage des cartes d'extension” dans le document Manuel du propriétaire.
Tableau 1-2. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Actions correctives E1B01 USBn Overcurrent Le périphérique connecté au port USB indiqué a provoqué une surtension. Remboîtez le câble du périphérique. Si l'incident persiste, remplacez le périphérique ou retirez-le. E2110 MBE DIMM # & # L'une des deux barrettes DIMM du groupe indiqué présente une erreur de mémoire multi-bits (MBE). Voir “Dépannage de la mémoire système” dans le document Manuel du propriétaire.
Tableau 1-2. Code I1915 Messages d'état affichés sur l'écran LCD (suite) Texte Causes Actions correctives Video Off La vidéo a été désactivée par l'utilisateur du contrôleur RAC. Pour information uniquement. La vidéo sera désactivée dans xx secondes par l'utilisateur du contrôleur RAC. Pour information uniquement. (L'écran LCD affiche un arrièreplan bleu ou orange.) I1916 Video Off in ## (L'écran LCD affiche un arrièreplan bleu ou orange.
Tableau 1-3. Options de l'écran Memory Information (Informations sur la mémoire) (suite) Option Description Video Memory (Mémoire vidéo) Affiche la taille de la mémoire vidéo. System Memory Testing (Test de la mémoire système) Indique si la mémoire système doit être testée à chaque amorçage. Les options disponibles sont Enabled (Activé) et Disabled (Désactivé). Redundant Memory (Mémoire redondante) (Option par défaut : Disabled [Désactivé]) Active ou désactive la fonction de mémoire redondante.
Écran CPU Information (Informations sur le processeur) Le tableau 1-4 met à jour la description des options associées à la gestion de l'alimentation en fonction de la demande. Tableau 1-4. Écran CPU Information (Informations sur le processeur) Option Description Demand-Based Power Management (Gestion de l'alimentation à la demande) (Option par défaut : Enabled [Activé]) REMARQUE : Voir la documentation du système d'exploitation pour vérifier que cette fonction est prise en charge.
Tableau 1-5. Options de l'écran Integrated Devices (Périphériques intégrés) (suite) Option Description OS Watchdog Timer (Temporisateur de surveillance du système d'exploitation) (Option par défaut : Disabled [Désactivé]) REMARQUE : Cette fonctionnalité est utilisable uniquement I/OAT DMA Engine (Moteur DMA I/OAT) (Option par défaut : Disabled [Désactivé]) Active ou désactive la technologie d'accélération des E/S (I/OAT).
Écran System Security (Sécurité du système) Le tableau 1-6 répertorie les nouvelles options disponibles pour le système PowerEdge 1950 III. REMARQUE : Les systèmes livrés en Chine ne sont pas équipés d'une puce TPM. PRÉCAUTION : Avant d'activer l'option TPM Security (Sécurité TPM), vérifiez que le système d'exploitation prend cette fonction en charge. Tableau 1-6.
Tableau 1-6. Nouvelles options de l'écran System Security (Sécurité du système) Option Description TPM Activation (Activation de la puce TPM) Modifie l'état de fonctionnement de la puce TPM. Lorsque l'option Activate (Activer) est sélectionnée, la puce TPM est activée par défaut. Lorsque l'option Deactivate (Désactiver) est sélectionnée, la puce TPM est désactivée. L'état No Change (Pas de changement) ne lance aucune action.
Tableau 1-7. Option de l'écran Serial Communication (Communication série) Option Description Failsafe Baud Rate (115200 default) - Débit de la ligne de secours (par défaut 115200) Indique le débit de la ligne de secours utilisé pour la redirection de console lorsque ce débit ne peut pas etre négocié automatiquement avec le terminal distant. Ce débit ne doit pas être modifié.
Support système pour Microsoft Windows 2000 Si vous faites appel à l'outil System Build and Update Utility (Utilitaire de mise à jour et de compilation du système), Microsoft® Windows® 2000 est inclus dans la liste des systèmes d'exploitation répertoriés dans l'onglet Server OS Install (Installation du système d'exploitation). Ce système d'exploitation est pris en charge par les systèmes PowerEdge 1950 et 1950 II, mais pas par le système PowerEdge 1950 III.
Dell™ PowerEdge™ 1950 Systeme Informationsaktualisierung
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie das System besser einsetzen können. VORSICHTSHINWEIS: Hiermit werden Sie auf mögliche Gefahrenquellen hingewiesen, die Hardwareschäden oder Datenverlust zur Folge haben können, wenn die Anweisungen nicht befolgt werden.
Inhalt Nicht-optimale Speicherkonfigurationen . . . . . . . . PowerEdge 1950 III – Neue Systemmerkmale. Neue Leistungsmerkmale 85 . . . . . 85 . . . . . . . . . . . . . 85 Neue Netzteil- und Energieüberwachungsmerkmale zur Effizienzmaximierung . . . . . . . . 85 . . . 86 . . . . . . . . . . . . 86 Neue E/A- und Datenspeicherungsmerkmale Neue Sicherheitsmerkmale Optionaler interner USB-Speicherstick . . . . . . . . . 86 Installieren des optionalen internen USB-Speichersticks . . . . . . .
. . . . 104 . . . . . . . . 104 . . . . . . . . . . 105 Aktualisierung des System-Setup-Programms Bildschirm „Memory“ (Speicher) . Bildschirm „CPU-Information“ (Prozessorinformationen) . . . Bildschirm „Integrated Devices“ (Integrierte Geräte) . . . . . . . . . . . . . . . . 106 Bildschirm „System Security“ (Systemsicherheit) . . . . . . . . . . . . . . . . 107 Informationen zum Betriebssystem . . . . . . . . . . 109 Nummerierung der NICs . . . . . . . . . . . . .
Nicht-optimale Speicherkonfigurationen Der POST wird möglicherweise unterbrochen, wenn eine nicht-optimale Speicherkonfiguration erkannt wird. Folgende Meldung wird angezeigt: Non-Optimal Memory Configuration Press F1 to continue or F2 for Setup ANMERKUNG: Der Einsatz von DIMM-Modulen unterschiedlicher Taktraten bedeutet, dass die Speicherkonfiguration nicht optimal ist. Das System betreibt den DIMM-Satz des Kanals mit der niedrigsten Taktrate und entsprechend verminderter Leistung.
Neue E/A- und Datenspeicherungsmerkmale • Optionaler Gigabit-Ethernet-Netzwerkadapter mit vier Ports; unterstützt Datenübertragungsraten von 10 MBit/s, 100 MBit/s und 1000-MBit/s und Fernstart über iSCSI • Unterstützung für 10-GB-Ethernet-Karten • Ein interner USB 2.
Abbildung 1-1. Position des internen USB-Anschlusses 1 2 1 Systemplatine 2 Position des internen USB-Anschlusses Um vom USB-Speicherstick zu starten, müssen Sie den USB-Speicherstick mit einem Boot-Image konfigurieren und den USB-Speicherstick in der Startreihenfolge des System-Setup-Programms spezifizieren. Siehe „Verwenden des System-Setup-Programms“ im Hardware-Benutzerhandbuch.
Installieren des optionalen internen USB-Speichersticks WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Ausführliche Informationen zu den Sicherheitsvorkehrungen beim Arbeiten im Innern des Computers und zum Schutz vor elektrischer Entladung finden Sie im Produktinformationshandbuch. 1 Schalten Sie das System und alle angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Stromnetz.
5 Setzen Sie das Speicherkühlgehäuse wieder ein. 6 Schließen Sie das System. Siehe „Schließen des Systems“ im HardwareBenutzerhandbuch. 7 Verbinden Sie das System mit dem Netzstrom und starten Sie das System neu. 8 Rufen Sie das System-Setup-Programm auf und überprüfen Sie, ob der USB-Stick vom System erkannt wurde. Siehe „Verwenden des SystemSetup-Programms“ im Hardware-Benutzerhandbuch.
Prozessor-Upgrades – PowerEdge 1950 IIund PowerEdge 1950 III-Systeme • Wenn Ihr Systemgehäuse an der Vorderseite mit einer „II“ gekennzeichnet ist, kann Ihr System auf die Dual Core-Prozessoren der Reihe Intel Xeon 5100 und die Quad-Core-Prozessoren der Reihe Intel Xeon 5300 aktualisiert werden.
Aktualisierung von Systemmeldungen Tabelle 1-1 enthält neue Systemmeldungen für PowerEdge 1950 III-Systeme sowie die wahrscheinliche Ursache und die geeignete Korrekturmaßnahme, wenn die betreffende Meldung angezeigt wird. WARNUNG: Nur zugelassene Servicetechniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Innern des Systems zugreifen.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen !!*** Error: Remote Initialisierungsfehler Access Controller des Remote-Accessinitialization Controllers. failure *** RAC virtual USB devices may not be available... Korrekturmaßnahmen Stellen Sie sicher, dass der Remote-Access-Controller ordnungsgemäß installiert ist. Siehe „Installieren einer RAC-Karte“ im HardwareBenutzerhandbuch.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen PCI BIOS failed to install Prüfsummenfehler bei PCIe-Geräte-BIOS (Options-ROM) während des Shadowing erkannt. Setzen Sie die Erweiterungskarte(n) neu ein. Stellen Sie sicher, dass alle erforderlichen Kabel sicher mit den Erweiterungskarten verbunden sind. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Fehlerbehebung bei System-Erweiterungskarten“ im HardwareBenutzerhandbuch.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen PCIe Degraded Link Fehlerhafte oder nicht Width Error: Slot n ordnungsgemäß installierte Expected Link Width PCIe-Erweiterungskarte im angegebenen Steckplatz. is n Actual Link Width is n Korrekturmaßnahmen Setzen Sie die PCIe-Karte neu in den angegebenen Steckplatz ein. Nähere Hinweise erhalten Sie im Abschnitt „Erweiterungskarten“ im HardwareBenutzerhandbuch.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen PCIe Training Error: Slot n Fehlerhafte oder nicht ordnungsgemäß installierte PCIe-Erweiterungskarte im angegebenen Steckplatz. Setzen Sie die PCIe-Karte neu in den angegebenen Steckplatz ein. Nähere Hinweise erhalten Sie im Abschnitt „Erweiterungskarten“ im HardwareBenutzerhandbuch. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Wie Sie Hilfe bekommen“ im HardwareBenutzerhandbuch.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen TPM operation is Es wurde eine pending. Press I to Konfigurationsänderung Ignore or M to angefordert. Modify to allow this change and reset the system. WARNING: Modifying could prevent security. Korrekturmaßnahmen Drücken Sie auf I, um den Systemstart fortzusetzen. Drücken Sie auf M, um die TPM-Einstellung zu ändern und neu zu starten. Fehlerhafte oder falsch eingesetzte Speichermodule.
Tabelle 1-1. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site. Unzulässige Speicherkonfiguration erkannt. Das System läuft, jedoch mit eingeschränkter Funktionalität. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind.
Ergänzende Informationen zu LCDStatusmeldungen Tabelle 1-2 enthält aktualisierte Meldungen der LCD-Statusanzeige, die bei PowerEdge 1950 III-Systemen angezeigt werden können, sowie Informationen zu den möglichen Ursachen. Die LCD-Meldungen beziehen sich auf Ereignisse, die im Systemereignisprotokoll (System Event Log = SEL) aufgezeichnet werden. Informationen über das SEL und über die Konfiguration der Systemverwaltungseinstellungen finden Sie in der Dokumentation der Systemverwaltungssoftware. Tabelle 1-2.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1118 CPU Temp Interface Der BMC kann den Temperaturzustand der CPU(s) nicht bestimmen. Zur Vorbeugung maximiert der BMC die CPU-Lüfterdrehzahl. Schalten Sie das System aus und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Wie Sie Hilfe bekommen“ im HardwareBenutzerhandbuch.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1711 PCI PERR B## D## F## Das System-BIOS hat einen PCIParitätsfehler bei einer Komponente im PCIKonfigurationsraum bei Bus Nr. ##, Gerät Nr. ##, Funktion Nr. ## gemeldet. Entfernen Sie die PCIe-Erweiterungskarten, und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Fehlerbehebung bei einer Erweiterungskarte“ im HardwareBenutzerhandbuch.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1712 PCI SERR B## D## F## Das System-BIOS hat einen PCISystemfehler bei einer Komponente im PCIKonfigurationsraum bei Bus Nr. ##, Gerät Nr. ##, Funktion Nr. ## gemeldet. Entfernen Sie die PCIe-Erweiterungskarten, und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Fehlerbehebung bei Erweiterungskarten“ im HardwareBenutzerhandbuch.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E171F PCIE Fatal Err Das System-BIOS B## D## F## hat einen schwerwiegenden PCIe-Fehler bei einer Komponente im PCIeKonfigurationsraum bei Bus Nr. ##, Gerät Nr. ##, Funktion Nr. ## gemeldet. Entfernen Sie die PCIe-Erweiterungskarten, und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Fehlerbehebung bei Erweiterungskarten“ im HardwareBenutzerhandbuch.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1B01 USB# Overcurrent Gerät am angegebenen USBPort hat einen Überstromzustand verursacht. Schließen Sie das Gerätekabel neu an. Wenn das Problem weiterhin besteht, ersetzen oder entfernen Sie das Gerät. E2110 MBE DIMM # & # Eines der beiden angegebenen DIMM-Speichermodule weist einen Speicher-Mehrfachbitfehler (Multi-Bit Error = MBE) auf.
Tabelle 1-2. Meldungen der LCD-Statusanzeige (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen I1915 Die BildschirmDient nur zur ausgabe wurde vom Information. (LCD leuchtet mit RAC-Remoteblauem oder gelbem benutzer Hintergrund.) ausgeschaltet. I1916 Video Off in ## Video Off Die Bildschirmausgabe wird in xx (LCD leuchtet mit Sekunden vom blauem oder gelbem RAC-Remotebenutzer Hintergrund.) ausgeschaltet. Dient nur zur Information.
Tabelle 1-3. Optionen im Bildschirm „Memory Information“ (Speicherinformationen) (fortgesetzt) Option Beschreibung Node Interleaving (Standardeinstellung Disabled) Wenn diese Option aktiv ist (Einstellung Enabled), wird Speicher-Interleaving unterstützt, wenn eine symmetrische Speicherkonfiguration installiert ist. Wenn die Option deaktiviert ist (Einstellung Disabled), unterstützt das System asymmetrische Speicherkonfigurationen (NUMA = Non-Uniform Memory Architecture).
Bildschirm „Integrated Devices“ (Integrierte Geräte) In Tabelle 1-5 sind neue Optionen des Bildschirms „Integrated Devices“ (Integrierte Geräte) aufgeführt. Tabelle 1-5. Optionen des Bildschirms „Integrated Devices“ (Integrierte Geräte) Option Beschreibung Internal USB Port Aktiviert oder deaktiviert den internen USB-Port des Systems.
Bildschirm „System Security“ (Systemsicherheit) Tabelle 1-6 enthält neue Optionen für das PowerEdge 1950 III-System. ANMERKUNG: In China ausgelieferte Systeme sind nicht mit TPM ausgerüstet. VORSICHTSHINWEIS: Bevor Sie die Option TPM Security aktivieren, vergewissern Sie sich, dass das Betriebssystem TPM unterstützt. Tabelle 1-6.
Tabelle 1-6. Neue Optionen des Bildschirms „System Security“ (Systemsicherheit) Option Beschreibung TPM Clear (Standardeinstellung No) VORSICHTSHINWEIS: Löschen des TPM führt zum Verlust aller Schlüssel im TPM. Dies verhindert, dass das Betriebssystem gestartet werden kann und führt zu Datenverlusten, falls sich die Schlüssel nicht wiederherstellen lassen. Achten Sie darauf, die TPM-Schlüssel zu sichern, bevor Sie diese Option aktivieren.
Informationen zum Betriebssystem Nummerierung der NICs Bei Linux-Betriebssystemen mit dem udev-Kernel-Gerätemanager erfolgt die Nummerierung der NICs anders als bei früheren Linux-Versionen mit dem devfs-Gerätemanager.
Aktualisierungen des HardwareBenutzerhandbuchs Prozessor installieren Bei der Installation des Prozessors muss die Prozessorabdeckung geschlossen werden, bevor der Prozessor mit dem Sicherungshebel des Sockels befestigt wird. Benutzerdefinierte Systemdiagnose-Testoptionen Im Fenster Customizing (Anpassen) der Systemdiagnose befindet sich die Option Log output file pathname (Verzeichnisname der Protokollausgabedatei). Hier können Sie das Diskettenlaufwerk bzw.
Dell™ PowerEdge™ 1950 システム アップデート情報
メモ、注意、警告 メモ:コンピュータを使いやすくするための重要な情報を説明し ています。 注意 : 手順に従わない場合は、ハードウェアの損傷やデータの損 失の可能性があることを示しています。 警告: 物的損害、けが、または死亡の原因となる可能性がある ことを示しています。 ____________________ 本書の内容は予告なく変更されることがあります。 © 2006 ~ 2009 すべての著作権は Dell Inc. にあります。 Dell Inc. の書面による許可のない複製は、いかなる形態においても厳重に禁じられてい ます。 本書に使用されている商標:Dell、DELL ロゴ、および PowerEdge は Dell Inc.
目次 最適でないメモリ構成 . . . . . . . . . . . . . . . . PowerEdge 1950 III – 新しいシステム機能 新しい性能特性 . 115 . . . . . . 115 . . . . . . . . . . . . . . . . . 115 新しい高能率電源ユニットと電源 監視機能 . . . . . . . . . . . . . . . . . . . . . . 115 . . . . . . . . . . . 116 . . . . . . . . . . . . 116 I/O とストレージの新機能 . 新しいセキュリティ機能 オプションの内蔵 USB メモリキー . . . . . . . . . オプションの内蔵 USB メモリキー の取り付け . . . . . . . . . . . . . . . . . . . . 118 . . . . . . . . 119 . . . . . . . . . . .
セットアップユーティリティのアップデー ト情報 . . . . . . . . . . . . . . . . . . . . . . メモリ画面 . . . . 132 . . . . . . . . . . . . . . . . . . . 132 CPU Information(CPU 情報) 画面 . . . . . . . . . . . . . . . . . . . . . . . . Integrated Devices(内蔵デバイス) 画面 . . . . . . . . . . . . . . . . . . . . . . . . System Security(システムセキュリティ) 画面 . . . . . . . . . . . . . . . . . . . . . . . OS の情報 135 . . . . . . . . . . . . . . . . . . . . . . . 137 . . . . . . . . . . . . . . . . . . . .
最適でないメモリ構成 メモリ構成が最適でないことが検知されると POST が中断され、 次のメッセージが表示されます。 Non-Optimal Memory Configuration (メモリ構成が最適ではありません) Press F1 to continue or F2 for Setup (続行するには F1 を、セットアップに進むには F2 を押します) メモ:速度の異なる DIMM を混在させると、メモリ構成が最適でなくな ります。システムは、チャネルの DIMM セット内の最も遅い DIMM に合わ せてパフォーマンスをクロックダウンします。 PowerEdge 1950 III – 新しいシステム機能 新しい性能特性 • デュアルコア / クアッドコア Intel® Xeon® 5400 シリーズおよび 5300 シリーズのプロセッサが 2 個。 • 8 GB メモリモジュール対応。 新しい高能率電源ユニットと電源監視機能 • さまざまな負荷に応じた出力変換によるシステム効率の向上。 • ベースボード管理コントローラ(BMC)による電源監視機能による、 システム内の電流、電圧、お
I/O とストレージの新機能 • 10-Mbps、100-Mbps、および 1000-Mbps のデータ転送速度と iSCSI リモートブートをサポートするオプションの Intel クアッドポートギ ガビットイーサネット NIC。 • 10 Gb イーサネットカードに対応。 • オプションの起動可能 USB フラッシュドライブまたは USB メモリ キーをサポートする内蔵 USB 2.
図 1-1. 内部 USB コネクタの位置 1 2 1 システム基板 2 内部 USB コネクタの位置 USB メモリキーから起動するには、起動イメージを使用して USB メモ リキーを設定し、セットアップユーティリティの起動順序で USB メモ リキーを指定する必要があります。『ハードウェアオーナーズマニュア ル』の「セットアップユーティリティの使い方」を参照してください。 USB メモリキー上に起動可能ファイルを作成する方法については、 USB メモリキーに付属のユーザーマニュアルを参照してください。 メモ:複数の LUN を持つ USB キーは、キーの製造元が提供するフォー マットユーティリティを使用してフォーマットする必要があります。 メモ:システム内部のコンポーネントとの干渉を避けるために、 USB キーは最大サイズ(厚み 11.68 mm x 幅 24.89 mm x 長さ 66.
オプションの内蔵 USB メモリキーの取り付け 警告:システムのカバーを取り外して内部の部品に手を触れる作 業は、トレーニングを受けたサービス技術者のみが行ってください。 安全上の注意、コンピュータ内部の作業、および静電気障害への対処 の詳細については、『製品情報ガイド』を参照してください。 1 システムと周辺機器の電源を切り、システムをコンセントから外し ます。 2 システムカバーを開きます。『ハードウェアオーナーズマニュアル』 の「システムカバーの取り外し」を参照してください。 3 メモリ冷却用エアフローカバーを取り外します。『ハードウェアオー ナーズマニュアル』の「メモリ冷却用エアフローカバーの取り外し」 を参照してください。 4 システム基板上の USB コネクタの位置を確認し、USB メモリキーを USB コネクタに挿入します。図 1-2 を参照してください。 図 1-2.
5 メモリ冷却用エアフローカバーを取り付けます。 6 システムカバーを閉じます。『ハードウェアオーナーズマニュアル』 の「システムカバーの取り付け」を参照してください。 7 システムを電源に接続し、システムの電源を入れます。 8 セットアップユーティリティを起動し、USB キーがシステムによっ て検出されたことを確認します。『ハードウェアオーナーズマニュ アル』の「セットアップユーティリティの使い方」を参照してくだ さい。 8 GB メモリモジュールのサポート – PowerEdge 1950 III システム PowerEdge 1950 III システムでは、認定された次の 8 GB メモリ構成が 新たにサポートされます。 • 64 GB — 8 GB クアッドランクのメモリモジュール 8 枚 • 48 GB — 8 GB クアッドランクおよび 4 GB デュアルランクのメモリ モジュール各 4 枚 64 GB のメモリが取り付けられている場合、POST 中に認識されて表示 されるのは 63.
プロセッサのアップグレード – PowerEdge 1950 II/III システム • システムシャーシの前面に「II」のラベルがある場合、お使いのシス テムは、デュアルコア Intel Xeon プロセッサの 5100 シリーズ、お よびクアッドコア Intel Xeon プロセッサの 5300 シリーズにアップ グレードできます。 • システムシャーシの前面に「III」のラベルがある場合、お使いのシ ステムは、デュアルコア Intel Xeon プロセッサの 5100/5200 シリー ズ、およびクアッドコア Intel Xeon プロセッサの 5300/5400 シリー ズにアップグレードできます。 お使いのシステムで利用できる最新のプロセッサアップグレードオプ ションについては、support.dell.
システムメッセージのアップデート PowerEdge 1950 III システム用の新しいシステムメッセージ、および メッセージが表示された場合の考えられる原因と対応処置のリストを 表 1-1 に示します。 警告:システムのカバーを取り外して内部の部品に手を触れる作 業は、トレーニングを受けたサービス技術者のみが行ってください。 安全上の注意、コンピュータ内部の作業、および静電気障害への対処 の詳細については、『製品情報ガイド』を参照してください。 表 1-1. システムメッセージ メッセージ 原因 対応処置 Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving.
表 1-1. システムメッセージ (続き) メッセージ 原因 対応処置 !!*** Error: Remote Remote Access Access Controller Controller の初期化エ initialization ラー。 failure *** RAC virtual USB devices may not be available...
表 1-1.
表 1-1.
表 1-1. システムメッセージ (続き) メッセージ 原因 TPM configuration operation honored. システムがここでリセッ 情報表示のみです。 トされる。 TPM Failure 信頼済みプラットフォー 『ハードウェアオーナー ムモジュール(TPM)の ズマニュアル』の「困っ 機能に障害が発生した。 たときは」を参照してく ださい。 TPM operation is 構成の変更が要求さ pending. Press I to れた。 Ignore or M to Modify to allow this change and reset the system. WARNING: Modifying could prevent security. Warning: Following faulty DIMMs are disabled: DIMM n1 n2 Total memory size is reduced.
表 1-1. システムメッセージ (続き) メッセージ 原因 Warning! No micro code update loaded for processor n マイクロコードのアップ BIOS ファームウェアを デートに失敗した。 アップデートします。 『ハードウェアオーナー ズマニュアル』の「困っ たときは」を参照してく ださい。 Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site.
LCD ステータスメッセージのアップデート PowerEdge 1950 III システムで表示される可能性のある LCD ステータ スメッセージとその考えられる原因のアップデート情報を 表 1-2 に示 します。LCD メッセージは、システムイベントログ(SEL)に記録され たイベントに基づきます。SEL およびシステム管理設定の詳細につい ては、システム管理ソフトウェアのマニュアルを参照してください。 表 1-2.
表 1-2.
表 1-2.
表 1-2.
表 1-2.
セットアップユーティリティのアップデート 情報 メモリ画面 Memory Information(メモリ情報)画面の情報フィールドに表示さ れる説明を 表 1-3 に示します。 表 1-3.
CPU Information(CPU 情報)画面 Demand-Based Power Management(デマンドベースの電力管理) オプションの最新の説明を 表 1-4 に示します。 表 1-4. CPU Information(CPU 情報)画面 オプション 説明 Demand-Based Power Management (デフォルトは Enabled) メモ:OS のマニュアルを参照し、この機能をサ ポートしているかどうかを確認します。 デマンドベースの電力管理を有効または無効にし ます。有効時には、CPU パフォーマンス状態を示す 表が OS に報告されます。無効時には、CPU パ フォーマンス状態を示す表は OS に報告されません。 デマンドベースの電力管理をサポートしない CPU が 1 つでもある場合は、フィールドは読み取り専用と なり、自動的に Disabled(無効)に設定されます。 Integrated Devices(内蔵デバイス)画面 新しくなった Integrated Devices(内蔵デバイス)画面のオプション を 表 1-5 に示します。 表 1-5.
表 1-5. Integrated Devices(内蔵デバイス)画面のオプション (続き) オプション OS Watchdog Timer (デフォルトは Disabled) 説明 メモ:この機能は、ACPI 3.
System Security(システムセキュリティ)画面 PowerEdge 1950 III システムの新しいオプションを 表 1-6 に示します。 メモ:中国に出荷されるシステムには TPM が装備されていません。 注意 : TPM Security(TPM セキュリティ)オプションを有効にする前に、 OS が TPM に対応していることを確認してください。 表 1-6.
表 1-6. System Security(システムセキュリティ)画面の新しいオプション (続き) オプション 説明 注意 : TPM をクリアすると、TPM 内のすべての暗 TPM Clear (デフォルトは No) 号化キーが失われます。このオプションを選択す ると OS からの起動ができなくなり、暗号化キー が復元できない場合はデータが失われます。 このオプションを有効にする前に必ず TPM キー をバックアップしてください。 Yes(はい)に設定すると、TPM の内容がすべてクリ アされます。 メモ:TPM Security(TPM セキュリティ)が Off(オフ) に設定されている場合、このフィールドは読み取り専 用です。 デフォルトの Failsafe Baud Rate(フェイルセーフボーレート)に関す るアップデート情報を表 1-7 に示します。 表 1-7.
OS の情報 NIC の列挙 udev カーネルデバイスマネージャを使用するバージョンの Linux OS では、NIC を列挙する順序が devfs デバイスマネージャを使用する旧 バージョンの Linux とは異なります。システムの機能は影響を受けませ んが、Red Hat® Enterprise Linux®(バージョン 4 またはバージョン 5) もしくは SUSE® Linux Enterprise Server 9 または 10 を使用している場 合は、NIC が逆順に列挙され、NIC1 が eth0 ではなく eth1 として、 NIC2 が eth1 ではなく eth0 として設定されます。デバイスの既定の 列挙順序を変更する方法については、linux.dell.
『ハードウェアオーナーズマニュアル』の アップデート プロセッサの取り付け プロセッサの取り付けの際には、ソケットリリースレバーでプロセッサ を固定する前にプロセッサシールドを閉じる必要があります。 システム診断プログラムのカスタムテストオプション システム診断プログラムの Customize(カスタマイズ)ウィンド ウで、Log output file pathname(ログ出力ファイルのパス名)オプ ションを使用すると、テストログファイルが保存されるディスケットドラ イブまたは USB メモリキーを指定することができます。このファイルを ハードドライブに保存することはできません。 138 アップデート情報
Dell™ PowerEdge™ 1950 시스템 설명서 갱신본
주 , 주의 및 경고 주: 주는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제 공합니다. 주의: 주의는 지침을 준수하지 않을 경우의 하드웨어 손상이나 데이터 손실 위험을 설명합니다. 경고 : 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험 이 있음을 알려줍니다 . ____________________ 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다. © 2006–2009 Dell Inc. 저작권 본사 소유. Dell Inc.의 서면 승인 없이 어떠한 경우에도 무단 복제하는 것을 엄격히 금합니다. 본 설명서에 사용된 상표인 Dell, DELL 로고 및 PowerEdge는 Dell Inc.의 상표이며; Intel 및 Xeon 은 Intel Corporation의 등록 상표입니다. Microsoft, Windows 및 Windows Server는 미국 및/또는 기타 국가에서 Microsoft Corporation의 상표 또는 등록 상표입니다.
차례 최적이 아닌 메모리 구성 . . . . . . . . . . . . . . . PowerEdge 1950 III – 새 시스템 기능 새로운 성능 기능 . . . . . . . . . 143 . . . . . . . . . . . . . . . . . 143 높은 효율성의 새로운 전원 공급 장치 및 전원 모니터링 기능 . . . . . . . . . . . 143 . . . . . . . . . . . . . 144 . . . . . . . . . . . . . . . . . . . 144 새로운 I/O 및 저장 기능 . 새 보안 기능 . 143 내장형 USB 메모리 키 옵션 . . . . . . . . . . . . . . 내부 USB 메모리 키 옵션 설치 . . . . . . . . . . 8GB 메모리 모듈 지원 - PowerEdge 1950 III 시스템 . . . . . . . . . . . . . . . . . . . . .
System Setup 프로그램 업데이트 메모리 화면 . . . . . . . . . . 158 . . . . . . . . . . . . . . . . . . . 158 CPU 정보 화면 . . . . . . . . . . . . . . . . . . 통합 장치 화면 . . . . . . . . . . . . . . . . . . 시스템 보안 화면 160 . . . . . . . . . . . . . . . . . . . . 162 . . . . . . . . . . . . . . . . . . . . . 162 RHEL – 잘못된 프로세서 정보 Microsoft Windows 2000 에 대한 시스템 지원 . . . . . . . . . . . . . . . 162 . . . . . . . . . 162 하드웨어 소유자 설명서 업데이트 . . . . . . . . . 163 . . . . . . . . . . . . . . . . . .
최적이 아닌 메모리 구성 최적 상태가 아닌 메모리 구성이 감지되면 POST가 중지되고 다음과 같은 메 시지가 나타납니다. Non-Optimal Memory Configuration 최적이 아닌 메모리 구성 Press F1 to continue or F2 for Setup 계속하려면F1을 누르거나 설정하려면 F2를 누릅니다. 주: 속도가 다른 DIMM을 혼합하면 메모리 구성이 최적 상태가 아니게 됩 니다. 시스템이 성능 속도를 채널에 대한 DIMM 설정에서 가장 낮은 속도로 낮춥니다. PowerEdge 1950 III – 새 시스템 기능 새로운 성능 기능 • 듀얼 코어 또는 쿼드 코어 Intel® Xeon® 5400 시리즈 및 5300 시리즈 프 로세서 • 8GB 메모리 모듈 지원 높은 효율성의 새로운 전원 공급 장치 및 전원 모니터링 기능 • 작업 부하 시 전력 보존에 대한 보다 높은 시스템 효율성.
새로운 I/O 및 저장 기능 • 10-Mbps, 100-Mbps 및 1000-Mbps 데이터 전송률 및 iSCSI 원격 부팅을 지원하는 Intel 4중 포트 Gigabit Ethernet NIC 옵션 1개. • 10-Gb Ethernet 카드 지원. • 부팅 가능한 USB 플래시 드라이브 옵션 또는 USB 메모리 키를 지원하 는 USB 2.0 규격의 내장형 커넥터 1개. • SAS 6i/R 옵션 및 PERC 6/i 어댑터 옵션 지원. 새 보안 기능 • 향상된 보안을 위해 TPM (Trusted Program Module) 지원. • iSCSI 부팅 선택적 지원. 내장형 USB 메모리 키 옵션 PowerEdge 1950 III 시스템은 USB 플래시 메모리 키와 함께 사용할 시스템 보 드에 위치한 내장형 USB 커넥터를 제공합니다(그림 1-1 참조). USB 메모리 키는 부팅 장치, 보안 키 또는 대용량 저장 장치로 사용할 수 있습니다.
그림 1-1. 내장형 USB 커넥터 위치 1 2 1 시스템 보드 2 내장형 USB 커넥터 위치 USB 메모리 키에서 부팅하려면 부팅 이미지로 USB 메모리 키를 구성한 다음 시스템 설치 프로그램의 부팅 순서에서 USB 메모리 키를 지정해야 합 니다. 하드웨어 소유자 설명서의 "System Setup 프로그램 사용"을 참조하십 시오. USB 메모리 키에서 부팅 파일을 작성하는 방법에 대한 내용은 USB 메 모리 키와 함께 제공된 사용 설명서를 참조하십시오. 주: 여러 LUN (Logical Unit Numbers)이 포함된 USB 키는 키 제조업체에서 제공 하는 포맷 유틸리티를 사용하여 포맷해야 합니다. 주: 시스템 내부의 구성부품 간섭을 피하려면 USB 키는 다음과 같은 최대 크기를 준수해야 합니다. 11.68mm 두께(0.46") x 24.89mm 너비(0.98") x 66.8mm 길이(2.63").
내부 USB 메모리 키 옵션 설치 경고 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부의 구성요소에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전기 방전 방지에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다. 2 시스템을 엽니다. 하드웨어 소유자 설명서의 "시스템 열기"를 참조하십 시오. 3 메모리 냉각 덮개를 분리하십시오. 하드웨어 소유자 설명서의 "메모리 냉각 덮개 분리"를 참조하십시오. 4 시스템 보드의 USB 커넥터를 찾은 다음 USB 커넥터에 USB 메모리 키 를 삽입하십시오. 그림 1-2를 참조하십시오. 그림 1-2.
5 메모리 냉각 덮개를 교체하십시오. 6 시스템을 닫습니다. 하드웨어 소유자 설명서의 "시스템 닫기"를 참조하 십시오. 7 시스템을 전원에 다시 연결하고 시스템을 재시작합니다. 8 시스템 설치 프로그램을 시작하고 시스템에서 USB 키를 감지했는지 확 인합니다. 하드웨어 소유자 설명서의 "System Setup 프로그램 사용"을 참조하십시오. 8GB 메모리 모듈 지원 - PowerEdge 1950 III 시스템 PowerEdge 1950 III 시스템은 다음과 같이 승인된 8GB 메모리 구성을 추가로 지원합니다. • 64GB — 8 x 8GB 4중 등급 메모리 모듈 • 48GB — 4 x 8GB 4중 등급 및 4 x 4GB 2중 등급 메모리 모듈 64GB의 메모리가 설치되어 있을 경우 시스템에서는 POST 도중 63.75GB만 인식하여 표시합니다. 참고 : 시스템을 업그레이드하기 전에 시스템의 BIOS 가 최신 버전인지 확인하십 시오 .
시스템 보드 교체 – 암호화된 데이터 보호 Windows Server® 2008을 사용하는 PowerEdge 1950 III 시스템에서 BitLocker 유틸리티 등의 암호화 프로그램을 사용하여 하드 드라이브의 내용을 보호할 수 있습니다. 암호화 응용프로그램으로 TPM을 사용 중인 경우 시스템 설치 도중 복구 키 를 작성하라는 메시지가 나타납니다. 이 복구 키는 반드시 저장하십시오. 시스템 보드를 교체할 경우 하드 드라이브의 암호화된 파일을 액세스하기 전에 시스템을 다시 시작할 때 복구 키를 입력해야 합니다. 시스템 메시지 업데이트 표 1-1에는 메시지가 나타날 때 PowerEdge 1950 III 시스템에 대한 새 시스템 메시지, 발생 가능한 원인 및 조치 목록이 표시됩니다. 경고 : 숙련된 서비스 기술자만 시스템 덮개를 분리하고 시스템 내부 의 구성부품에 액세스해야 합니다 . 안전 지침 , 컴퓨터 내부 작업 및 정전 기 방전 보호에 대한 자세한 내용은 제품 정보 안내를 참조하십시오 . 표 1-1.
표 1-1. 시스템 메시지 ( 계속 ) 메시지 원인 !!*** Error: Remote 원격 액세스 컨트롤러 초기 Access Controller 화가 실패했습니다. initialization failure *** RAC virtual USB devices may not be available... 수정 조치 원격 액세스 컨트롤러가 올 바르게 설치되었는지 확인 합니다. 하드웨어 소유자 설명서의 "RAC 카드 설치" 를 참조하십시오. Invalid PCIe card found in the Internal_Storage slot! 전용 저장 컨트롤러 슬롯에 PCIe 확장 카드를 분리하 잘못된 PCIe 확장 카드가 고 전용 슬롯에 내장형 SAS 설치되어 있으므로 시스템 컨트롤러를 설치하십시오. 이 정지되었습니다.
표 1-1. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 특정 PCIe 장치가 잘못되 SAS 컨트롤러 도터 카드의 었거나 제대로 설치되어 있 경우 전용 PCIe 커넥터에 카드를 다시 장착하십시오. 지 않습니다. 하드웨어 소유자 설명서의 Expected Link Width "SAS 컨트롤러 도터 카드 is n 설치"를 참조하십시오. Actual Link Width 문제가 지속될 경우 하드웨 is n 어 소유자 설명서의 "도움 말 얻기"를 참조하십시오. PCIe Degraded Link Width Error: Integrated device PCIe Degraded Link 지정된 슬롯에 설치된 Width Error: Slot n PCIe 카드에 오류가 있거 Expected Link Width 나 잘못 설치되었습니다. is n Actual Link Width is n 지정된 슬롯 번호에 PCIe 카드를 다시 장착합니다. 하드웨어 소유자 설명서의 "확장 카드"를 참조하십 시오.
표 1-1. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 Remote Access Controller cable error or incorrect card in the RAC slot. RAC 케이블이 연결되어 있 지 않거나 RAC 카드가 잘 못된 확장 슬롯에 설치되어 있습니다. RAC 케이블이 연결되어 있 는지, RAC 카드가 올바른 확장 슬롯에 설치되어 있는 지 확인합니다. 하드웨어 소유자 설명서의 "RAC 카 드 설치"를 참조하십시오. 주: POST 중에 BMC 옵션 ROM이 로드된 후 모든 TPM 정보 메시지가 나타납니다. TPM configuration operation honored. 시스템이 지금 재설정됩 니다. TPM Failure TPM(신뢰할 수 있는 플랫 하드웨어 소유자 설명서의 폼 모듈) 기능이 실패했습 "도움말 얻기"를 참조하십 니다. 시오. TPM operation is 구성 변경이 요청되었습 pending. Press I to 니다.
표 1-1. 시스템 메시지 ( 계속 ) 메시지 원인 수정 조치 Warning! No micro code update loaded for processor n 마이크로 코드 업데이트가 BIOS 펌웨어를 업데이트합 실패했습니다. 니다. 하드웨어 소유자 설 명서의 "도움말 얻기"를 참 조하십시오. Warning: The 잘못된 메모리 구성입니다. installed memory 시스템은 실행되지만 기능 configuration is 이 감소됩니다. not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site. 메모리 모듈이 올바른 구성 으로 설치되어 있는지 확인 합니다. 하드웨어 소유자 설명서의 "일반 메모리 모 듈 설치 지침"을 참조하십 시오.
LCD 상태 메시지 업데이트 표 1-2에는 PowerEdge 1950 III 시스템에서 발생할 수 있는 LCD 상태 메시지 및 각 메시지의 가능한 원인에 대한 업데이트 목록이 표시됩니다. LCD 메시 지는 SEL(시스템 이벤트 로그)에 기록된 이벤트를 나타냅니다. SEL 및 시스 템 관리 설정 구성에 대한 자세한 내용은 시스템 관리 소프트웨어 설명서를 참조하십시오. 표 1-2. LCD 상태 메시지 코드 텍스트 원인 수정 조치 N/A SYSTEM NAME 시스템 설치 프로그 램에서 사용자가 정 의할 수 있는 62개의 문자열입니다. 이 메시지는 참조 전 용입니다. SYSTEM NAME 은 다음과 같은 조건에 서 표시됩니다: • 시스템의 전원이 켜진 경우 • 전원이 꺼지고 활 성 오류가 표시된 경우 시스템 설치 프로그 램에서 시스템 ID와 이름을 변경할 수 있 습니다. 하드웨어 소 유자 설명서의 "System Setup 프로 그램 사용"을 참조 하십시오.
표 1-2. LCD 상태 메시지 ( 계속 ) 코드 텍스트 원인 수정 조치 E1211 ROMB Batt RAID 전지가 장착 되지 않았거나 불량 이거나 열 문제로 재 충전할 수 없습니다. RAID 전지 커넥터 를 다시 장착합니다. 하드웨어 소유자 설명서의 "RAID 배 터리" 및 "시스템 냉 각 문제 해결"을 참 조하십시오. E1625 PS AC Current 전원이 적당한 범위 AC 전원을 검사합 를 벗어났습니다. 니다. E1711 PCI PERR B## D## F## 시스템 BIOS에서 PCI 구성 공간(버스 ##, 장치 ##, 기능 ##)에 있는 구성요 소에 대한 PCI 패리 티 오류를 보고했습 니다. PCIe 확장 카드를 분리하고 다시 장착 합니다. 문제가 지속 될 경우 하드웨어 소유자 설명서의 "확장 카드 문제 해 결"을 참조하십 시오. PCI PERR Slot # 지정된 PCIe 슬롯에 상주한 구성부품의 PCI 패리티 오류가 시스템 BIOS에 보 고되었습니다.
표 1-2. LCD 상태 메시지 ( 계속 ) 코드 텍스트 원인 수정 조치 E1712 PCI SERR B## D## F## 시스템 BIOS에서 PCI 구성 공간 (버스 ##, 장치 ##, 기능 ##)에 있는 구성요 소에 대한 PCI 시스 템 오류를 보고했습 니다. PCIe 확장 카드를 분리하고 다시 장 착합니다. 문제가 지 속될 경우 하드웨 어 소유자 설명서의 "확장 카드 문제 해 결"을 참조하십 시오. PCI SERR Slot # 지정된 슬롯에 있는 구성요소의 PCI 시 스템 오류가 시스템 BIOS에 보고되었습 니다. 확장 카드 라이저를 다시 설치합니다. 하드웨어 소유자 설 명서의 "확장 카드 라이저"를 참조하십 시오. 문제가 지속되면 시 스템 보드의 라이저 카드에 결함이 있는 것입니다. 하드웨 어 소유자 설명서의 "도움말 얻기"를 참 조하십시오.
표 1-2. LCD 상태 메시지 ( 계속 ) 코드 텍스트 원인 수정 조치 E171F PCIE Fatal Err PCIe 구성 공간 B## D## F## (버스 ##, 장치 ##, 기능 ##)에 상주한 구성부품의 PCIe 치 명적인 오류가 시스 템 BIOS에 보고되 었습니다. PCIe 확장 카드를 분리하고 다시 장착 합니다. 문제가 지 속될 경우 하드웨 어 소유자 설명서의 "확장 카드 문제 해 결"을 참조하십 시오. PCIE Fatal Err 지정된 슬롯에 있는 Slot # 구성요소의 PCIe 치 명적인 오류가 시스 템 BIOS에 보고되 었습니다. 확장 카드 라이저를 다시 설치합니다. 하드웨어 소유자 설 명서의 "확장 카드 라이저"를 참조하십 시오. 문제가 지속되면 시 스템 보드의 라이저 카드에 결함이 있 는 것입니다. 하드웨 어 소유자 설명서의 "도움말 얻기"를 참 조하십시오. E1914 DRAC5 Conn2 Cbl DRAC 5 케이블이 케이블을 다시 연결 없거나 분리되었습 합니다.
표 1-2. LCD 상태 메시지 ( 계속 ) 코드 텍스트 원인 수정 조치 E2111 SBE Log 시스템 BIOS가 메 Disable DIMM # 모리 단일 비트 오류 (SBE) 로깅을 비활 성화했으며 시스템 이 재시작될 때까지 추가 SBE 로깅을 재 시작하지 않습니다. "#"는 BIOS와 관련 된 DIMM을 표시합 니다. 하드웨어 소유자 설 명서의 "시스템 메 모리 문제 해결"을 참조하십시오. E2112 Mem Spare DIMM # 메모리에 오류가 너 무 많이 존재함을 확 인했기 때문에 시스 템 BIOS는 메모리 를 스페어링했습 니다. "# & #" 는 BIOS와 관련된 DIMM 쌍을 표시 합니다. 하드웨어 소유자 설 명서의 "시스템 메 모리 문제 해결"을 참조하십시오. I1915 Video Off ( 비디오 끄기 ) RAC 원격 사용자가 참조용으로만 제공 비디오를 껐습니다. 됩니다.
System Setup 프로그램 업데이트 메모리 화면 표 1-3은 Memory Information (메모리 정보) 화면에 나타나는 정보 필드에 대한 설명을 나열합니다. 표 1-3. 메모리 정보 화면 옵션 옵션 설명 System Memory Size (시스템 메모리 크기) 시스템 메모리의 크기를 표시합니다. System Memory Type (시스템 메모리 종류) 시스템 메모리의 종류를 표시합니다. System Memory Speed (시스템 메모리 속도) 시스템 메모리의 속도를 표시합니다. Video Memory (비디오 메모리) 비디오 메모리의 크기를 표시합니다. System Memory Testing (시스템 메모리 검사) 시스템 부팅 시 시스템 메모리 검사를 실행할지 여부를 지정합니다. 옵션으로 Enabled (활성화) 및 Disabled (비활성화)가 있습니다.
CPU 정보 화면 표 1-4는 Demand-Based Power Management (요구 기반의 전원 관리) 옵션에 대한 설명을 업데이트합니다. 표 1-4. CPU 정보 화면 옵션 설명 Demand-Based Power Management (수요 기반 전원 관리) (기본값: Enabled (활성화)) 주: 운영 체제가 이 기능을 지원하는지 확인하려면 운 영 체제 설명서를 참조하십시오. 수요 기반 전원 관리 기능을 활성화하거나 비활성화합 니다. 활성화된 경우 CPU 성능 상태 표가 운영 체제에 보고되고 비활성화된 경우 CPU 성능 상태 표가 운영 체 제에 보고되지 않습니다. 일부 CPU가 수요 기반 전원 관 리를 지원하지 않을 경우 필드는 읽기 전용으로 되며 자 동으로 Disabled (비활성화)로 설정됩니다. 통합 장치 화면 표 1-5에는 새 Integrated Devices (통합 장치) 화면 옵션 목록이 표시됩니다. 표 1-5.
표 1-5. 통합 장치 화면 옵션 ( 계속 ) 옵션 설명 I/OAT DMA Engine(I/OAT DMA 엔진) (기본값: Disabled (비활성화)) I/OAT(I/O Acceleration Technology) 옵션을 활성화 또는 비활 성화합니다. Enabled (사용)로 설정되어 있으면 I/OAT가 DMA 엔진에 대한 TCP 수신 동작의 일부를 오프로드하여 TCP를 사용하는 응용프로그램에 대한 시스템 CPU 이용률 을 줄입니다. System Interrupts 이 필드는 시스템의 PCI 장치에 대한 인터럽트 할당을 제어 Assignment(시스템 합니다. Distributed (배포)로 설정되어 있으면 인터럽트 라 인터럽트 할당) 우팅이 다시 구성되어 장치 간의 IRQ 공유를 최소화합니다. (Standard (표준) 기본값) 시스템 보안 화면 표 1-6에는 PowerEdge 1950 III 시스템의 새 옵션 목록이 표시됩니다.
표 1-6. 새 시스템 보안 화면 옵션 ( 계속 ) 옵션 설명 TPM Activation (TPM 활성화) TPM의 작동 상태를 변경합니다. Activate (활성화)로 설정하는 경우 TPM이 기본 설정으 로 사용되고 활성화됩니다. Deactivate (비활성화)로 설정하는 경우 TPM이 사용되 지 않고 비활성화됩니다. No Change (변경 없음) 상태에서는 아무런 동작도 시작 되지 않습니다. TPM의 작동 상태는 변경되지 않은 상태 로 유지됩니다(TPM에 대한 모든 사용자 설정이 유지됨). 주: TPM Security (TPM 보안)를 Off (끄기)로 설정하는 경 우 이 필드는 읽기 전용입니다. 주의 : TPM 을 지우면 TPM 의 모든 암호화 키가 TPM Clear(TPM 지우기) (기본값: No (아니오)) 유실됩니다 . 이 옵션은 운영 체제로 부팅하는 것 을 방지하므로 암호화 키를 복원할 수 없는 경우 데이터가 유실됩니다 .
운영 체제 정보 NIC 열거 udev 커널 장치 관리자를 사용하는 Linux 운영 체제 버전은 devfs 장치 관리 자를 사용한 이전 Linux 버전보다 다르게 NIC를 열거합니다. 시스템 기능에 아무런 영향을 주지 않아도 Red Hat® Enterprise Linux® (version 4 또는 version 5) 또는 SUSE® Linux Enterprise Server 9 또는 10 운영 체제를 사용하 면 NIC가 거꾸로 열거됩니다. NIC1은 eth0 대신 eth1로, NIC2는 eth1 대신 eth0으로 구성됩니다. 기본 장치 열거 변경 방법에 대한 내용은 linux.dell.com에서 사용 가능한 "네트워크 인터페이스 카드 이름 지정" 백서 를 참조하십시오.
하드웨어 소유자 설명서 업데이트 프로세서 설치 프로세서를 설치할 때 소켓 분리 레버로 프로세서를 고정하기 전에 프로세 서 실드를 닫아야 합니다. 시스템 진단 사용자 지정 테스트 옵션 시스템 진단 프로그램의 사용자 지정 창에서 출력 파일 경로 이름 기록 옵션 을 사용하면 테스트 로그 파일이 저장되는 위치에 디스켓 드라이브 또는 USB 메모리 키를 지정할 수 있습니다. 하드 드라이브에는 파일을 저장할 수 없습니다.
정보 갱신본
Sistemas Dell™ PowerEdge™ 1950 Actualización de información
Notas, precauciones y avisos NOTA: Una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. PRECAUCIÓN: Un mensaje de PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos si no se siguen las instrucciones. AVISO: Un mensaje de AVISO indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin previo aviso. © 2006–2009 Dell Inc.
Contenido Configuraciones de memoria no óptimas . . . . . . . . 169 . . 169 . . . . . . . . . 169 PowerEdge 1950 III: Nuevas funciones del sistema Nuevas funciones de rendimiento Nuevas funciones de supervisión de energía y fuente de alimentación de alta eficiencia . . . . . . . . . . . . . . . . . . 169 . . . 170 . . . . . . . . . . 170 Memoria USB interna opcional . . . . . . . . . . . . . 170 Instalación de la memoria USB interna opcional . . . . . . . . . . . . . . . .
Actualización del programa de configuración del sistema . . . . . . . . . . . . . . . . . . . Pantalla de memoria . . . . 187 . . . . . . . . . . . . . . . 187 Pantalla de información de la CPU . Pantalla Integrated Devices . . . . . . . 189 . . . . . . . . . . . 189 . . . . . . . . 190 Pantalla de seguridad del sistema Información sobre el sistema operativo . Enumeración de NIC . . . . . . . 193 . . . . . . . . . . . . . . . 193 RHEL: Información incorrecta del procesador .
Configuraciones de memoria no óptimas Si se detecta una configuración de memoria que no es óptima, es posible que la POST se detenga y que aparezca el mensaje siguiente: Non-Optimal Memory Configuration (Configuración de memoria no óptima). Press F1 to continue or F2 for Setup (Pulse F1 para continuar o F2 para abrir el programa de configuración del sistema) NOTA: Si se combinan módulos DIMM de velocidades distintas, la configuración de la memoria pasa a ser no óptima.
Nuevas funciones de E/S y almacenamiento • Una NIC Ethernet Gigabit Intel de cuatro puertos opcional que admite velocidades de datos de 10 Mbps, 100 Mbps y 1 000 Mbps y el inicio remoto iSCSI. • Compatibilidad con tarjetas Ethernet Gigabit 10. • Un conector interno compatible con USB 2.0 que admite una unidad flash USB de inicio opcional o una memoria USB. • Compatibilidad con adaptadores SAS 6i/R y PERC 6/i opcionales.
Ilustración 1-1. Ubicación del conector USB interno 1 2 1 Placa base 2 Ubicación del conector USB interno Para iniciar desde la memoria USB, debe configurarla con una imagen de inicio y luego especificarla en la secuencia de inicio mediante el programa de configuración del sistema. Consulte “Uso del programa de configuración del sistema” en el Manual del propietario del hardware.
Instalación de la memoria USB interna opcional AVISO: Los técnicos de servicio especializados son las únicas personas autorizadas para retirar las cubiertas y acceder a los componentes internos del sistema. Consulte la Guía de información del producto para obtener información completa sobre las precauciones de seguridad, la manipulación de las piezas internas del ordenador y la protección contra descargas electrostáticas.
5 Vuelva a colocar la cubierta de refrigeración de la memoria. 6 Cierre el sistema. Consulte “Cierre del sistema” en el Manual del propietario del hardware. 7 Vuelva a conectar el sistema a la alimentación y reinícielo. 8 Abra el programa de configuración del sistema y compruebe que el sistema haya detectado la memoria USB. Consulte “Uso del programa de configuración del sistema” en el Manual del propietario del hardware.
Actualizaciones de procesador para los sistemas PowerEdge 1950 II y PowerEdge 1950 III • Si la parte frontal del chasis del sistema contiene la identificación “II”, significa que el sistema puede actualizarse a los procesadores de doble núcleo Intel Xeon serie 5100 y a los procesadores de cuatro núcleos Intel Xeon serie 5300.
Actualización de los mensajes del sistema En la tabla 1-1 se enumeran los nuevos mensajes del sistema para el sistema PowerEdge 1950 III, así como la causa probable y la acción correctiva que debe llevarse a cabo cuando aparezca cada mensaje. AVISO: Los técnicos de servicio especializados son las únicas personas autorizadas para retirar las cubiertas y acceder a los componentes internos del sistema.
Tabla 1-1. Mensajes del sistema (continuación) Mensaje Causas !!*** Error: Remote Error de inicialización de Access Controller la controladora de acceso initialization remoto. failure *** RAC virtual USB devices may not be available... Acciones correctivas Asegúrese de que la controladora de acceso remoto está instalada correctamente. Consulte “Instalación de una tarjeta RAC” en el Manual del propietario del hardware.
Tabla 1-1. Mensajes del sistema (continuación) Mensaje Causas Acciones correctivas PCIe Degraded Link Width Error: Embedded dispositivo La placa base o la tarjeta vertical son defectuosas. Consulte “Obtención de ayuda” en el Manual del propietario del hardware. El dispositivo PCIe especificado es defectuoso o se ha instalado incorrectamente. En el caso de una tarjeta controladora secundaria SAS, vuelva a colocar la tarjeta en el conector PCIe dedicado.
Tabla 1-1. Mensajes del sistema (continuación) Mensaje Causas Acciones correctivas PCIe Training Error: Integrated dispositivo El dispositivo PCIe especificado es defectuoso o se ha instalado incorrectamente. En el caso de una tarjeta controladora secundaria SAS, vuelva a colocar la tarjeta en el conector PCIe dedicado. Consulte “Instalación de una tarjeta controladora secundaria SAS” en el Manual del propietario del hardware.
Tabla 1-1. Mensajes del sistema (continuación) Mensaje Causas Acciones correctivas TPM configuration operation honored. El sistema se restablecerá ahora. Mensaje meramente informativo. TPM Failure Se ha producido un error Consulte “Obtención de en una función del módulo ayuda” en el Manual del de plataforma segura propietario del hardware. (TPM). TPM operation is Se ha solicitado un cambio pending. Press I to de configuración. Ignore or M to Modify to allow this change and reset the system.
Tabla 1-1. Mensajes del sistema (continuación) Mensaje Causas Acciones correctivas Warning! No micro code update loaded for processor n La actualización del microcódigo ha fallado. Actualice el firmware del BIOS. Consulte “Obtención de ayuda” en el Manual del propietario del hardware. Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site.
Actualización de los mensajes de estado de la pantalla LCD En la tabla 1-2 se enumeran las actualizaciones de los mensajes de estado de la pantalla LCD que pueden producirse en el sistema PowerEdge 1950 III y la causa probable de aparición de cada mensaje. Los mensajes de la pantalla LCD se refieren a los eventos guardados en el registro de eventos del sistema (SEL).
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas Acciones correctivas E1118 CPU Temp Interface La BMC no puede determinar el estado de la temperatura de las CPU. Por lo tanto, la BMC aumenta la velocidad del ventilador de la CPU al máximo como medida cautelar. Apague y reinicie el sistema. Si el problema persiste, consulte “Obtención de ayuda” en el Manual del propietario del hardware.
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas Acciones correctivas E1711 PCI PERR B## D## F## El BIOS del sistema ha notificado un error de paridad PCI en un componente que se encuentra en el espacio de configuración PCI en el bus, dispositivo y función especificados. Extraiga y recoloque las tarjetas de expansión PCIe. Si el problema persiste, consulte “Solución de problemas de una tarjeta de expansión” en el Manual del propietario del hardware.
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas Acciones correctivas E1712 PCI SERR B## D## F## El BIOS del sistema ha notificado un error del sistema PCI en un componente que se encuentra en el espacio de configuración PCI en el bus, dispositivo y función especificados. Extraiga y recoloque las tarjetas de expansión PCIe. Si el problema persiste, consulte “Solución de problemas de tarjetas de expansión” en el Manual del propietario del hardware.
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas Acciones correctivas E171F PCIE Fatal Err El BIOS del sistema B## D## F## ha notificado un error grave PCIe en un componente que se encuentra en el espacio de configuración PCIe en el bus, dispositivo y función especificados. Extraiga y recoloque las tarjetas de expansión PCIe. Si el problema persiste, consulte “Solución de problemas de tarjetas de expansión” en el Manual del propietario del hardware.
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas Acciones correctivas E1B01 USB# Overcurrent El dispositivo conectado al puerto USB especificado ha provocado una sobrecorriente. Vuelva a colocar el cable del dispositivo. Si el problema persiste, sustituya o extraiga el dispositivo. E2110 MBE DIMM # & # Se ha producido un error de varios bits (MBE) de memoria en uno de los dos módulos DIMM indicados.
Tabla 1-2. Mensajes de estado de la pantalla LCD (continuación) Código Texto Causas I1915 I1916 Video Off in ## Acciones correctivas Video Off El usuario remoto (La pantalla LCD se de la RAC ha ilumina con una luz apagado el vídeo. de fondo azul o ámbar.) Mensaje meramente informativo. El usuario remoto de la RAC ha (La pantalla LCD se apagado el vídeo ilumina con una luz tras xx segundos. de fondo azul o ámbar.) Mensaje meramente informativo.
Tabla 1-3. Opciones de la pantalla de información de la memoria (continuación) Opción Descripción Redundant Memory (valor predeterminado: Disabled) Habilita o deshabilita la función de memoria redundante. Si se establece en Spare Mode (Modo de repuesto), se reserva el primer rango de memoria de cada módulo DIMM para la sustitución de memoria. Si el campo Node Interleaving (Intercalado de nodos) está activado, la función de memoria redundante estará desactivada.
Pantalla de información de la CPU En la tabla 1-4 se actualiza la descripción de la opción de administración de energía basada en la demanda. Tabla 1-4. Pantalla de información de la CPU Opción Descripción Demand-Based Power Management (valor predeterminado: Enabled) NOTA: Consulte la documentación del sistema operativo para verificar si admite esta función. Activa o desactiva la administración de energía basada en la demanda.
Tabla 1-5. Opciones de la pantalla de dispositivos integrados (continuación) Opción Descripción OS Watchdog Timer (valor predeterminado: Disabled) NOTA: Esta función sólo se puede utilizar con sistemas operativos compatibles con implementaciones WDAT de la especificación 3.0b de la interfaz avanzada de configuración y energía (ACPI). Microsoft® Windows Server® 2008 admite esta función, pero Windows Server 2003 no.
Tabla 1-6. Nuevas opciones de la pantalla de seguridad del sistema Opción Descripción TPM Security (valor predeterminado: Off) Define las notificaciones del módulo de plataforma segura (TPM) en el sistema. Si se establece en Off (Desactivar) (valor predeterminado), no se notifica la presencia del TPM al sistema operativo.
Tabla 1-6. Nuevas opciones de la pantalla de seguridad del sistema (continuación) Opción Descripción PRECAUCIÓN: Si se borra el TPM, se pierden todas TPM Clear (valor predeterminado: No) las claves de cifrado del TPM. De este modo se impide que se inicie desde el sistema operativo y se pierden los datos si no es posible restablecer las claves de cifrado. Realice una copia de seguridad de las claves del TPM antes de activar esta opción. Si se establece en Yes (Sí), se borra todo el contenido del TPM.
Información sobre el sistema operativo Enumeración de NIC Las versiones del sistema operativo Linux que utilizan el administrador de dispositivos kernel udev enumeran las NIC de forma distinta a las versiones anteriores de Linux, que utilizaban el administrador de dispositivos devfs.
Actualizaciones del Manual del propietario del hardware Instalación del procesador Al instalar el procesador, debe cerrarse el protector del procesador antes de fijar el procesador con la palanca de liberación del zócalo.