Dell™ PowerEdge™ C6100 시스템 하드웨어 소유자 매뉴얼 규정 모델 XS23-TY3
주 , 주의 및 경고 주 : 주는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제 공합니다 . 주의 : 주의는 지침을 준수하지 않을 경우의 하드웨어 손상이나 데이터 손실 위험을 설명합니다 . 경고 : 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험 이 있음을 알려줍니다 . _________________ 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다 . © 2009 Dell Inc. 저작권 본사 소유 . Dell Inc. 의 서면 승인 없이 어떠한 방식으로든 본 자료를 무단 복제하는 행위는 엄격히 금지 됩니다 . 본 설명서에 사용된 상표인 Dell, DELL 로고 및 PowerEdge 는 Dell Inc. 의 상표입니다 . Intel 은 미국 및 기타 국가에서 Intel Corporation 의 등록 상표입니다 ; Red Hat 은 미국 및 기타 국가에 서 Red Hat, Inc. 의 등록 상표입니다 .
목차 1 시스템 정보 . . . . . . . . . . . . . . . . . . . . . . . . 시작하는 동안 시스템 기능에 액세스 전면 패널 기능 및 표시등 . . . . . . . . . . . . . . . . . . 하드 드라이브 표시등 패턴 . . . . . . . . . . . . . . . . . 하드 드라이브 — 3.5 인치 하드 드라이브 — 2.5 인치 . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . 18 . . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . . . . 20 . . . . . . . . . . . . . . . . . . . . . . . 21 BMC 하트 비트 LED. 기타 필요한 정보 . . . . . .
고급 메뉴 . . . . . . . . . . . . . . . . . . . . . . . . . . . CPU 구성 . . . 메모리 구성 . IDE 구성 . . . 주 IDE 마스터 USB 구성 . . . PCI 구성 . . . 부팅 메뉴 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 38 39 39 41 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 부팅 설정 구성 보안 메뉴 . . . . . .
전원 공급 장치 . . . . . . . . . . . . . . . . . . . . . . . . 전원 공급 장치 분리 전원 공급 장치 설치 시스템 보드 조립품 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 58 . . . . . . . . . . . . . . . . . . . . . 58 시스템 보드 조립품 분리 시스템 보드 조립품 설치 냉각 덮개 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 59 . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 냉각 덮개 분리 냉각 덮개 설치 방열판 . 57 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 61 . . . .
시스템 배터리 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 RAID 배터리 ( 선택 사양 ) . . . . . . . . . . . . . . . . . . 80 RAID 배터리 분리 . . . . . RAID 배터리 설치 . . . . . RAID 배터리 캐리어 분리 . RAID 배터리 캐리어 설치 . 시스템 보드 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 . . . . . . . . . . . . . . . . . . . . . . . . .
4 시스템 문제 해결 안전 제일 - 사용자와 사용자 시스템의 안전을 위하여 . 설치 문제 109 . . . . . . . . . . . . . . . . . . . 109 . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 시스템 시작 오류 문제 해결. 외부 연결 문제 해결 . . . . . . . . . . . . . . . . 110 . . . . . . . . . . . . . . . . . . . . . 110 비디오 하위 시스템 문제 해결 USB 장치 문제 해결 . . . . . . . . . . . . . . . 110 . . . . . . . . . . . . . . . . . . . . . 110 직렬 I/O 장치 문제 해결 NIC 문제 해결 . . . . . . . . . . . . . . . . . . . . 111 . . . . . . . . . . . . . . . . . . . . . . .
5 점퍼 및 커넥터 . . . . . . . . . . . . . . . . . . . . 125 시스템 보드 커넥터 . . . . . . . . . . . . . . . . . . . . 125 . . . . . . . . . . . . . . . . . . . . . . . 126 후면판 커넥터 3.5 인치 드라이브 . 2.5 인치 드라이브 . 중앙판 커넥터 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 128 . . . . . . . . . . . . . . . . . . . . . . . 130 접속기 확장기 커넥터 메자닌 카드 커넥터 . . . . . . . . . . . . . . . . . . . 131 . . . . . . . . . . . . . . . . . . . . 132 팬 컨트롤러 보드 커넥터 . . . . . . . . . . . . . . . . .
시스템 정보 시작하는 동안 시스템 기능에 액세스 시작하는 동안 시스템 기능에 액세스하려면 다음 키를 입력합니다 . 키 입력 설명 시스템 설치 프로그램을 시작합니다 . 33 페이지의 " 시작 메뉴 " 를 참조하십시오 . BIOS 부팅 매니저를 시작합니다 . 34 페이지의 " 부팅에서 시스템 설치 옵션 " 을 참조하십시오 . PXE (Preboot eXecution Environment) 부팅을 시작합니다 . SAS 구성 유틸리티를 시작합니다 . 자세한 내용은 SAS 어댑터 설 명서를 참조하십시오 . RAID 구성 유틸리티를 시작합니다 . 자세한 내용은 SAS RAID 카 드 설명서를 참조하십시오 . PXE 부팅에 대한 NIC 설정을 구성하는 유틸리티를 시작합니다 . 자세한 내용은 내장형 NIC 설명서를 참조하십시오 .
전면 패널 기능 및 표시등 그림 1-1. 전면 패널 — 3.5 인치 하드 드라이브와 시스템 보드 4 개 12 34 5 그림 1-2. 6 7 8 9 1-0 2-0 3-0 4-0 1-1 2-1 3-1 4-1 1-2 2-2 3-2 4-2 전면 패널 — 2.
항목 표시등 , 단추 또는 커 아이콘 넥터 1, 3, 7, 9 전원 켜짐 표시등 / 전원 단추 ( 시스템 보드 1, 2, 4, 3) 2, 4, 6, 8 시스템 확인 표시등 / 단추 ( 시스템 보드 1, 2, 4, 3) 설명 시스템 전원이 켜진 상태이면 전원 표 시등이 켜집니다 . 전원 단추는 시스템으로의 DC 전원 공급 장치의 출력을 제어합니다 . 주 : 시스템에 설치된 메모리 양에 따 라 시스템 전원을 켤 때 비디오 모니터 에 이미지가 표시되는 데 몇 초에서 2 분 이상까지 걸릴 수 있습니다 . 주 : ACPI 를 지원하는 운영 체제에서 전원 단추를 사용하여 시스템을 끄면 시스템에 대한 전원 공급이 끊어지기 전에 점진적 종료가 수행됩니다 . 주 : 강제 종료하려면 전원 단추를 5 초 동안 누릅니다 . 확인 단추는 랙에 설치한 특정 시스템 및 시스템 보드의 위치를 찾을 때 사용 됩니다 . 단추를 누르면 , 전면과 후면의 청색 시스템 상태 표시등이 다시 누를 때까 지 깜박입니다 .
하드 드라이브 표시등 패턴 하드 드라이브 — 3.5 인치 그림 1-3. 하드 드라이브 표시등 — 3.5 인치 1 2 1 표 1-1. 하드 드라이브 작동 표시등 ( 녹색 ) 2 하드 드라이브 상태 표시등 ( 녹색 및 적색 ) 하드 드라이브 표시등 — 3.
하드 드라이브 — 2.5 인치 그림 1-4. 하드 드라이브 표시등 — 2.5 인치 1 1 하드 드라이브 작동 표시등 ( 녹색 ) 2 2 하드 드라이브 상태 표시등 ( 녹색 및 황색 ) 표 1-2. 하드 드라이브 표시등 — 2.
후면 패널 구조 및 표시등 그림 1-5. 1 그림 1-6. 후면 패널 — 시스템 보드 4 개 2 3 4 5 6 7 8 9 10 열거 — 시스템 보드 4 개 3 1 4 2 항목 표시등 , 단추 또는 커 아이콘 넥터 설명 1 전원 공급 장치 2(PS2) 1100W 2 전원 공급 장치 1(PS1) 1100W 3 USB 커넥터 (2 개 ) USB 장치를 시스템에 연결합니다 . 포 트는 USB 2.0 을 지원합니다 . 4 시스템 확인 표시등 시스템 관리 소프트웨어 및 전면에 있 는 식별 단추는 특정 시스템 및 시스템 보드를 식별할 때 표시등이 청색으로 깜박이게 합니다 . 문제가 발생하여 시스템에 주의가 필 요한 경우에는 황색으로 켜집니다 . 5 14 이더넷 커넥터 1 시스템 정보 내장형 10/100/1000 NIC 커넥터 .
항목 표시등 , 단추 또는 커 아이콘 넥터 설명 6 이더넷 커넥터 2 내장형 10/100/1000 NIC 커넥터 . 7 IP 포트의 KVM 전용 관리 포트 . 8 직렬 커넥터 직렬 장치를 시스템에 연결합니다 . 9 비디오 커넥터 VGA 디스플레이를 시스템에 연결합 니다 . 10 전원 켜짐 표시등 / 전 원 단추 ( 시스템 보드 1) 시스템 전원이 켜진 상태이면 전원 표 시등이 켜집니다 . 전원 단추는 시스템으로의 DC 전원 공급 장치의 출력을 제어합니다 . 주 : 시스템에 설치된 메모리 양에 따 라 시스템 전원을 켤 때 비디오 모니터 에 이미지가 표시되는 데 몇 초에서 2 분 이상까지 걸릴 수 있습니다 . 주 : ACPI 를 지원하는 운영 체제에서 전원 단추를 사용하여 시스템을 끄면 시스템에 대한 전원 공급이 끊어지기 전에 점진적 종료가 수행됩니다 . 주 : 비점진적인 종료를 강제로 수행 하려면 전원 단추를 5 초 동안 누릅니 다.
NIC 표시등 코드 그림 1-7.
그림 1-8.
전원 및 시스템 보드 표시등 코드 시스템 전면 패널 및 후면 패널의 LED 는 시스템 시작 동안 오류 코드를 표 시합니다 . 전면 패널 LED 위치의 경우 , 3.5 인치 하드 드라이브 시스템은 그림 1-1 을 참조하고 2.5 인치 하드 드라이브 시스템은 그림 1-2 를 참조하 십시오 . 후면 패널의 LED 위치는 그림 1-5 를 참조하십시오 . 표 1-3 은 오류 코드와 관련한 상태를 나열합니다 . 표 1-3. 진단 표시등 코드 구성 요소 표시등 상태 전원 켜짐 표시등 녹색으로 켜져 있음 전원 켜짐 S0/S1 호박색으로 깜박임 전원 끄기 모드 S4/S5 의 BMC 치명적인 상 녹색 / 호박색으로 태 이벤트 깜박임 전원 끄기 모드 S0/S1 의 BMC 치명적인 상 태 이벤트 시스템 확인 표 청색으로 켜져 있음 섀시를 통해 IPMI 는 명령어 또는 ID 버튼 시등 입력 ID (ID Button Press ID) 가 켜져 있는 지 식별합니다 .
전원 공급 장치 표시등 코드 그림 1-9.
BMC 하트 비트 LED 시스템 보드는 BMC 디버그용 BMC 하트비트 LED (CR24) 를 제공합 니다 . BMC 펌웨어가 준비가 되면 , BMC 하트비트 LED 가 깜박입니다 . 그림 1-10.
POST 오류 코드 코드 BMC 로그인 원인 0000h 예 수정 조치 타이머 카운터 읽기 / 쓰기 오 10 초 동안 시스템에서 AC 전 류 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0003h 예 CMOS 배터리 오류 114 페이지의 " 시스템 배터리 문제 해결 " 를 참조하십시오 . 0004h 예 CMOS 진단 상태 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0005h 예 CMOS 검사 합 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 000Bh 예 CMOS 메모리 크기 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 .
코드 BMC 로그인 원인 0012h 예 CMOS 날짜 시간 오류 수정 조치 114 페이지의 " 시스템 배터 리 문제 해결 " 을 참조하십 시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0040h 예 새로 고침 타이머 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0041h 예 메모리 오류 표시 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0044h 예 DMAC 컨트롤러 오류 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0045h 예 DMAC1 채널 레지스터 오류 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오.
코드 BMC 로그인 원인 0047h 예 PMM 메모리 할당 오류 수정 조치 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0048h 예 암호 검사 오류 암호 재설정 134 페이지의 " 점퍼 설정 " 을 참조하십 시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 004Ah 예 ADM 모듈 오류 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . 004Bh 예 언어 모듈 오류 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . 005Dh 예 ATA SMART 기능 오류 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . 005Eh 예 치명적이지 않은 암호 검사 오류 암호 재설정 134 페이지의 " 점퍼 설정 " 을 참조하십 시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 .
코드 BMC 로그인 원인 수정 조치 0063h 예 HDD 3 오류 119 페이지의 " 하드 드라이 브 문제 해결 " 을 참조하십시 오. 0064h 예 HDD 4 오류 119 페이지의 " 하드 드라이 브 문제 해결 " 을 참조하십시 오. 0065h 예 HDD 5 오류 119 페이지의 " 하드 드라이 브 문제 해결 " 을 참조하십시 오. 0066h 예 HDD 6 오류 119 페이지의 " 하드 드라이 브 문제 해결 " 을 참조하십시 오. 0067h 예 HDD 7 오류 119 페이지의 " 하드 드라이 브 문제 해결 " 을 참조하십시 오. 0080h 예 ATAPI 0 오류 0081h 예 ATAPI 1 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0082h 예 ATAPI 2 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 .
코드 BMC 로그인 원인 0084h 예 ATAPI 4 오류 수정 조치 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0085h 예 ATAPI 5 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0086h 예 ATAPI 6 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0087h 예 ATAPI 7 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0120h 예 PROCHOT# 로 인한 CPU1 열 오류 프로세서 방열판이 제대로 설치되었는지 확인합니다 .
코드 BMC 로그인 원인 0122h 예 PROCHOT# 로 인한 CPU3 열 오류 수정 조치 프로세서 방열판이 제대로 설치되었는지 확인합니다 . 122 페이지의 " 프로세서 문 제 해결 " 및 116 페이지의 " 시스템 냉각 문제 해결 " 을 참조하십시오 . 0123h 예 PROCHOT# 로 인한 CPU4 열 오류 프로세서 방열판이 제대로 설치되었는지 확인합니다 . 122 페이지의 " 프로세서 문 제 해결 " 및 116 페이지의 " 시스템 냉각 문제 해결 " 을 참조하십시오 . 0150h 예 프로세서 오류 BIST 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0151h 예 프로세서 오류 BIST 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 .
코드 BMC 로그인 원인 0160h 예 수정 조치 CPU1 프로세서 누락 마이크 BIOS 업데이트가 필요합니 로코드 다. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0161h 예 CPU2 프로세서 누락 마이크 BIOS 업데이트가 필요합니 로코드 다. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0162h 예 CPU3 프로세서 누락 마이크 BIOS 업데이트가 필요합니 로코드 다. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0163h 예 CPU4 프로세서 누락 마이크 BIOS 업데이트가 필요합니 로코드 다. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0180 예 CPU 1 스태핑 지원 안됨 프로세서가 해당 시스템의 시작 안내서에 약술한 프로 세서 기술 사양에서 설명된 종류와 일치하고 부합되는지 확인합니다 .
코드 BMC 로그인 원인 수정 조치 0183 예 CPU 4 스태핑 지원 안됨 프로세서가 해당 시스템의 시작 안내서에 약술한 프로 세서 기술 사양에서 설명된 종류와 일치하고 부합되는지 확인합니다 . L2 캐시 크기 불일치 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 0192h 예 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 0193h 예 CPUID, 프로세서 스태핑은 다릅니다 프로세서가 해당 시스템의 시작 안내서에 약술한 프로 세서 기술 사양에서 설명된 종류와 일치하고 부합되는지 확인합니다 . 0194h 예 CPUID, 프로세서 스태핑은 다릅니다 프로세서가 해당 시스템의 시작 안내서에 약술한 프로 세서 기술 사양에서 설명된 종류와 일치하고 부합되는지 확인합니다 . 0195h 예 전면 버스 불일치 프로세서가 해당 시스템의 시작 안내서에 약술한 프로 세서 기술 사양에서 설명된 종류와 일치하고 부합되는지 확인합니다 .
코드 BMC 로그인 원인 0198h 예 QPI 불일치 수정 조치 SEL 를 확인해 문제를 식별 하고 해결합니다 . 123 페이 지의 " 조사를 위한 시스템 이 벤트 로그 수집 " 을 참조하십 시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8101h 아니오 USB HC 검색 안됨 110 페이지의 "USB 장치 문 제 해결 " 을 참조하십시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8102h 아니오 USB 장치 Init 오류 110 페이지의 "USB 장치 문 제 해결 " 을 참조하십시오 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8103h 아니오 USB 장치 비활성화 USB 장치를 활성화하려면 , 41 페이지의 "USB 구성 " 을 참조하십시오 . 110 페이지의 "USB 장치 문 제 해결 " 을 참조하십시오 .
코드 BMC 로그인 원인 8105h 예 수정 조치 USB EHCI 64 비트 데이터 구 110 페이지의 "USB 장치 문 제 해결 " 을 참조하십시오 . 조 오류 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8301h 아니오 F000 에 SMBIOS 공간 부족 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8302h 아니오 F000 에 SMBIOS 공간 부족 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . 8400h 예 재지정 메모리 오류 117 페이지의 " 시스템 메모 리 문제 해결 " 을 참조하십시 오. 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 .
코드 BMC 로그인 원인 F003h 아니오 수정 조치 BIOS 업데이트 BMC FRU 오 10 초 동안 시스템에서 AC 전 류 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . F004h 아니오 BMC FRU 내부 영역 검사 합 10 초 동안 시스템에서 AC 전 불량 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . F005h 아니오 BIOS 업데이트 FRU 내부 영 10 초 동안 시스템에서 AC 전 역 검사 합 오류 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 . FFFFh 아니오 정의되지 않은 BIOS 오류 10 초 동안 시스템에서 AC 전 원을 분리하고 시스템을 재 시작합니다 . 문제가 지속되면 137 페이지 의 " 도움말 얻기 " 를 참조하 십시오 .
시스템 정보
시스템 설치 프로그램 사용 시작 메뉴 본 시스템은 플래시 메모리에 저장되어 있는 최신 AMI CMOS BIOS 를 사 용합니다 . 플래시 메모리는 플러그 앤 플레이 사양을 지원하고 , BIOS 설 치 프로그램 , 전원 공급 시 자체 검사 (POST) 루틴 , 및 PCI 자동 구성 유틸 리티가 포함되어 있습니다 . 본 시스템 보드는 시스템 BIOS 섀도잉을 지원해 , BIOS 가 64 비트 온보드 쓰기 방지 DRAM 에서 실행하는 것이 가능합니다 .
부팅에서 시스템 설치 옵션 POST 과정에서 를 눌러 설치를 초기화할 수 있습니다 . 콘솔 재지정 콘설 재지정을 통해 원격 사용자가 성공적으로 운영 체제를 부팅하지 못한 시스템의 문제를 진단하고 해결할 수 있습니다 . 콘솔 재지정의 가장 중요 한 부분은 BIOS 콘솔입니다 . BIOS 콘솔은 직렬 또는 모뎀 연결에 대한 입 력 및 출력을 재지정하는 플래시 ROM 상주 유틸리티입니다 . BIOS 는 직렬 포트에 대한 콘솔 재지정을 지원합니다 . 직렬 포트 기반 헤 드리스 시스템 지원이 시스템에 의해 제공되는 경우 , 시스템은 직렬 포트 에 대한 모든 BIOS 주도 콘솔 I/O 재지정 지원을 반드시 제공해야 합니다 . 직렬 콘솔용 드라이버가 ANSI 터미널 정의에 문서화된 기능을 지원하는 기능이 있어야 합니다 .
기본 메뉴 주 메뉴는 시스템 보드 및 BIOS 에 대한 정보를 표시합니다 . 기본 화면 그림 2-1. 시스템 설치 프로그램 기본 화면 Use [ENTER],[TAB] or [SHIFT-TAB] to select a field Use [+] or [-] to configure system Time. +– Tab F1 F10 ESC Select Screen Select Item Change Field Select Field General Help Save and Exit Exit 주 : 시스템 설치 프로그램의 옵션은 시스템 구성에 따라 변경됩니다 . 주 : 시스템 설치 프로그램 기본값은 다음 항목의 각 해당 옵션 아래에 표시됩 니다 .
AMIBIOS 설정 옵션 설명 Version ( 버전 ) BIOS 버전을 표시합니다 . 제조업체에서 BIOS 를 업데이트 하 는 경우 이 버전 번호를 확인하십시오 . Build Date ( 만든 날짜 ) BIOS 가 작성된 날짜를 표시합니다 . ID BIOS ID 를 표시합니다 . 프로세서 설정 옵션 설명 Type ( 종류 ) 시스템 보드에 설치된 프로세서 종류를 표시합니다 . Speed ( 속도 ) 프로세서의 최대 속도를 표시합니다 . Count ( 카운트 ) 설치된 프로세서의 수를 표시합니다 . 시스템 메모리 설정 옵션 설명 Size ( 크기 ) 얼마나 많은 메모리 (DRAM) 가 시스템 보드에 설치되어 있는 지를 표시합니다 . System Time ( 시스템 시간 ) 이 항목을 스크롤해 시간을 조정하십시오 . System Date ( 시스템 날짜 ) 이 항목을 스크롤해 시간을 조정하십시오 .
고급 메뉴 이 옵션은 시스템에 관한 고급 정보를 정의하는 항목 표를 표시합니다 . 주의 : 이러한 페이지에서 항목에 정확하지 않은 설정을 하면 시스템이 오작 동할 수 있습니다 . 이러한 항목을 조정한 경험이 없는 경우 , 이러한 설정을 기 본값으로 둘 것으로 권장합니다 . 이러한 페이지의 항목을 설정해 시스템이 오 작동하거나 시스템 부팅이 이루어지지 않는 경우 , BIOS 를 열고 종료 메뉴의 최적 기본값 로드 (Load Optimal Defaults) 를 선택해 정상적으로 부팅합니다 . CPU 구성 옵션 설명 QPI Frequency (QPI 주파수 ) 링크를 전속도 (full-speed) 로 변환할 때 ( 모든 구 성요소에 의해 지원되는 경우 ) 링크를 지정된 속도 로 변환합니다 . Virtualization Technology ( 가상화 기술 ) ( 기본값 : Disabled ( 비활성화 )) 프로세서가 VT 를 지원하는 경우 , 이 옵션을 활성 화합니다 .
옵션 설명 Active Processor Cores ( 활성 프로세서 코어 ) ( 기본값 : (All ( 모두 )) 각각의 프로세서 패키지에서 활성화할 수 있는 코 어수. Frequency Ratio ( 주파수 비율 ) 최소 및 최대 사이의 프로세서 비율을 설정합니다 . [+] 또는 [-] 를 사용해 해당 값을 구성합니다 . Intel(R) C-STATE tech ( 기본 CState: CPU 미사용은 C2/C3/C4 로 설정되어 있습 값 : Enabled ( 활성화 )) 니다 . CPU C6 Support (CPU C6 지 C6 지원 . CPU 가 미사용 모드인 경우 . 원 ) ( 기본값 : Enabled ( 활성화 )) 메모리 구성 옵션 설명 Memory Frequency ( 메모리 DDR3 주파수가 SPD 를 사용해 감지한 일반적인 주파수 ) ( 기본값 :1066 MHz) tck 보다 느리게 합니다 . Memory Mode( 메모리 모드 ) 독립 : 독립 채널 .
IDE 구성 주 : AHCI 포트는 고급 AHCI 또는 RAID 모드에 있을 때 설치 화면에 표시됩니 다. 옵션 설명 Configure SATA as (다음으로 SATA 를 구성합니다 : SATA 를 구성 ) • IDE • • • • – SATA#1 구성 ( 기본값 : Enhanced ( 고급 )) SATA#1 를 구성합니다 . – SATA#2 구성 ( 기본값 : Enhanced ( 고급 )) SATA#2 를 구성합니다 . 주 마스터 / 슬레이브는 SATA 포트 0/2 입니다 보조 마스터 / 슬레이브는 SATA 포트 1/3 입니다 AHCI/RAID AHCI Port 0~5 Hard Disk Write Protect ( 하 장치 쓰기 보호를 활성화 또는 비활성화합니다 . 이 드 디스크 쓰기 보호 ) ( 기본 는 장치에 BIOS 를 통해 액세스하는 경우에만 효율 값 : Disabled ( 비활성화 )) 적입니다 .
옵션 설명 PIO Mode(PIO 모드 ) ( 기본값 : Auto ( 자동 )) PIO 모드가 지원되는지 여부를 표시합니다 . Async DMA Async DMA 모드가 지원되는지 여부를 표시합니다 . Ultra DMA ( 울트라 DMA) 울트라 DMA 모드가 지원되는지 여부를 표시합니 다. S.M.A.R.T. S.M.A.R.T. 모드가 지원되는지 여부를 표시합니다 .
옵션 설명 DMA Mode(DMA 모드 ) ( 기본값 : Auto ( 자동 )) 프로세서를 사용하지 않고 채널에서 채널로 데이 터를 전송해 , 프로세서가 모든 바이트 전송에 사용 중일 때 데이터 전송 속도를 높이는 DMA ( 직접 메 모리 액세스 /Direct Memory Access) 모드를 선택합 니다 . • Auto ( 자동 ): 자동으로 최적 또는 기본 DMA 모드 를 감지합니다 . • SWDMA0 ~ SWDMA2: SingleWord DMA 0 ~ 2 를 선택합니다 . • MWDMA0 ~ MWDMA2: MultiWord DMA 0 ~ 2 를 선택합니다 . • UDMA 0 ~ UDMA5: Ultra DMA 0 ~ 5 를 선택합 니다 . S.M.A.R.T.
옵션 설명 Legacy USB Support ( 레거시 레거시 USB 장치에 대한 지원을 활성화합니다 . 자 USB 지원 ) ( 기본값 : 동 옵션은 연결된 USB 장치가 없는 경우 , 레거지 Enabled ( 활성화 ) 지원을 비활성화합니다 . USB 2.0 Controller Mode (USB 2.0 컨트롤러 모드 ) ( 기본값 : HiSpeed) HiSpeed (480 Mbps) 또는 FullSpeed (12 Mbps) 의 USB 2.0 컨트롤러를 구성합니다 . BIOS EHCI Hand-Off (BIOS 이는 EHCI 핸드오프 지원이 없는 운영 체제에 대 EHCI 핸드 오프 ) ( 기본값 : 한 화피 방법입니다 . EHCI 소유권 변경은 EHCI Enabled ( 활성화 )) 드라이버에서 주장해야 합니다 . USB Mass Storage Reset Delay 시작 장치 명령어가 생성된 이후 POST 가 USB 대 ( 대용량 저장 재설정 용량 저장 장치를 기다리는 시간 ( 초 ).
부팅 메뉴 옵션 설명 Boot Settings Configuration ( 부팅 설정 구성 ) 시스템 부팅 중에 설정을 구성합니다 . Boot Device Priority ( 부팅 장치 우선 순위 ) 부팅 장치 우선 순위를 지정합니다 . Hard Disk Drives ( 하드 디스크 드라이브 ) 사용 가능한 하드 드라이브에서 부팅 장치 우선 순 위 순서를 지정합니다 . Removable Drives ( 이동식 드라이브 ) 사용 가능한 이동식 드라이브에서 부팅 장치 우선 순위 순서를 지정합니다 . CD/DVD Drives: (CD/DVD 드라이브 :) 사용 가능한 CD/DVD 드라이브에서 부팅 장치 우 선 순위 순서를 지정합니다 . 부팅 설정 구성 옵션 설명 Quick Boot ( 빠른 부팅 ) BIOS 가 POST 중에 부팅 시 시간을 늦추는 특정 검 ( 기본값 : Enabled ( 활성화 )) 사를 건너 뛰도록 합니다 .
옵션 설명 Change Supervisor Password ( 관리자 암호 변경 ) 암호를 설치 , 변경 , 삭제합니다 . 이러한 항목을 선택하고 Enter 를 누르면 , 대화 상 자가 열리고 암호를 입력할 수 있습니다 . 6 자 이하 의 문자 또는 숫자를 입력할 수 있습니다 . 암호를 입력한 후 Enter 를 누릅니다 . 두 번째 대화 상자가 열려 확인을 위해 암호를 다시 입력할 것을 요청합 니다 . 암호를 정확하게 다시 입력한 후 Enter 를 누 릅니다 . 암호가 부팅 시에 필요하거나 사용자가 설 치 유틸리티를 시작할 때 필요합니다 . User Access Level ( 사용자 액 사용자 액세스 레벨을 설정합니다 : 세스 레벨 ) • No Access ( 액세스 없음 ): 사용자는 Setup Utility ( 설치 유틸리티 ) 에 접근할 수 없습니다 .
Server Menu ( 서버 메뉴 ) 주 : 지연 시간 , 최소 시간 , 최대 시간은 AC Power Recovery Delay (AC 전원 복 구 지연 ) 이 User define ( 사용자 정의 ) 로 설정되어 있는 경우 설치 (SETUP) 화 면에만 표시됩니다 . 전원 켜기나 마지막 상태로 AC 전원 손실 설치 복원을 선 택하면 AC 전원을 켜고 BMC 초기화를 실행하는데 60 초가 소요됩니다 . 옵션 설명 Power Management ( 전원 전원 모드를 설정합니다 . 옵션은 다음과 같습니다 . 관리 ) ( 기본값 : Node • 최대 성능 Management • 운영 체제 Control/EIST ( 노드 관리 )) • 활성 전원 컨트롤러 • 노드 관리 Maximum Performance ( 최대 성능 ) 또는 Active Power Controller ( 활성 전원 컨트롤러 ) 를 선택한 경 우 , Intel SpeedStep 이 비활성화됩니다 .
옵션 설명 AC Power Recovery Delay (AC 전원 복원 지연 ) ( 기본값 : Immediate ( 즉시 )) BMC 초기화 후 시스템 전원 켜기 시간을 선택합니다 . • Immediate (즉시): BMC 초기화 직후 전원을 켭니다. • Random ( 임의 ): 전원 켤 시간을 임의로 선택합니다 . • User define (사용자 정의): 사용자가 시간을 선택합니 다. – Delay Time ( 지연 시간 ): 최소와 최대 사이의 AC 전원 복원 지연 시간을 설정합니다 . 시스템 관리 옵션 설명 Server Board Part Number ( 서버 보드 부품 번호 ) 서버 보드 부품 번호를 표시합니다 . Server Board Serial Number ( 서버 보드 시리얼 번호 ) 서버 보드 시리얼 번호를 표시합니다 . NIC 1 MAC Address (NIC 1 MAC 주소 ) NIC1 MAC 주소를 표시합니다 .
원격 액세스 구성 옵션 설명 Remote Access( 원격 액세스 ) 원격 액세스 종류를 선택합니다 . ( 기본값 :Enabled ( 활성화 )) Serial Port Number ( 시리얼 포트 번호 ) ( 기본값 : COM1) 콘솔 재지정을 위한 시리얼 포트를 선택합니다 . 선 택한 포트가 활성화되어 있는지 확인합니다 . 이 항 목은 Remote Access ( 원격 액세스 ) 가 비활성화되 어 있는 경우 사라집니다 . Serial Port Mode ( 시리얼 포트 모드 ) ( 기본값 : 115200 8,n,1) 시리얼 포트 설정을 선택합니다 . 이 항목은 Remote Access ( 원격 액세스 ) 가 비활성화되어 있 는 경우 사라집니다 . Flow Control 콘솔 재지정을 위한 흐름 제어를 선택합니다 . 이 ( 흐름 제어 ) ( 기본값 : None 항목은 Remote Access ( 원격 액세스 ) 가 비활성화 ( 없음 )) 되어 있는 경우 사라집니다 .
주 : Flow Control ( 흐름 제어 ) 가 Software ( 소프트웨어 ) 로 설정되어 있는 경 우 , 원격 Hyper Terminal ( 하이퍼 터미널 ) 은 를 누르면 중단됩니다 . 그러나 는 또한 온보드 NIC PXE Option ROM 구성 설정을 위한 Setup Key Stroke ( 설치 키 스트로크 ) 입니다 . 따라서 를 눌렀을 때 원격 하 이퍼 터미널이 중단되는 것을 피하기 위해 PXE OPROM 구성에서 사용자가 를 로 변경할 것을 권장합니다 . IPMI 구성 옵션 설명 Status Of BMC (BMC 상태 ) BMC 상태를 표시합니다 . BMC Firmware Revision (BMC 펌웨어 개정판 ) BMC 펌웨어 개정판을 표시합니다 .
IP 주소 옵션 설명 IP Address(IP 주소 ) ( 기본값 XXX.XXX.XXX.XXX 의 형태의 십진법으로 IP 주소 은 BMC 설정에 좌우됩니다 ) 를 입력합니다 (XXX 는 256 이하이고 십진법 형태 만 허용됩니다 ). 주 : BMC IP 상태가 고정된 경우 , IP 주소가 유용합니다 . 서브넷 마스크 옵션 설명 Subnet Mask ( 서브넷마스크 ) ( 기본값은 BMC 설정에 좌우됩니다 ) XXX.XXX.XXX.XXX 의 형태의 십진법으로 서브넷 마스크를 입력합니다 (XXX 는 256 이하이고 십진 법 형태만 허용됩니다 ). 주 : BMC IP 상태가 고정된 경우 , 서브넷 마스크가 유용합니다 . 디폴트 게이트웨이 IP 옵션 설명 Default Gateway IP ( 디폴트 게이트웨이 IP) ( 기본값은 BMC 설정에 좌우됩니다 ) XXX.XXX.XXX.
종료 메뉴 옵션 설명 Save Changes and Exit ( 변경 사항 저장 및 종 료) 이 항목을 선택하고 Enter 를 눌러 설치 유틸리티의 변경 사항을 저장하고 설치 유틸리티를 종료합니다 . 변경 사항 저장 및 종료 대화상자가 표시되면 , [OK] 를 선택해 변경 사항을 저장하고 종 료하거나 N 을 눌러 설치 기본 메뉴로 되돌아갑니다 . Discard Changes and Exit ( 변경 사항 취소 및 종 료) 이 항목을 선택하고 Enter 를 눌러 설치 유틸리티의 변경 사항을 취소하고 설치 유틸리티를 종료합니다 . 변경 사항 취소 및 종료 대화상자가 표시되면 , [OK] 를 선택해 변경 사항을 취소하고 종 료하거나 N 을 눌러 설치 기본 메뉴로 되돌아갑니다 . Discard 이 항목을 선택하고 Enter 를 눌러 설치 유틸리티를 종료하지 않 Changes ( 변경 고 변경 사항을 취소합니다 .
시스템 구성요소 설치 안전 지침 경고 : 아직 전원 공급 장치에 연결되어 있는 시스템에서 작업하는 것은 매우 위험할 수 있습니다 . 주의 : 시스템 구성요소 및 전자 회로 보드는 정전기 방전으로 인해 손상될 수 있습니다 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 부상이나 시스템 손상을 방지하려면 다음 지침을 따릅니다 : • 시스템 내부 작업을 할 때마다 항상 시스템을 전원 콘센트에서 분리합 니다 . • 가능한 경우, 시스템 내부 작업을 할 때 손목 접지대를 착용하십시오.
시스템 내부 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주의 : 올바른 냉각을 위해 본 시스템은 반드시 시스템 덮개가 설치된 상태에 서 작동해야 합니다 . 주 : 본 항목의 그림은 3.5 인치 하드 드라이브가 장착된 시스템을 보여줍니다 . 그림 3-1.
하드 드라이브 3.5 인치 하드 드라이브 및 2.5 인치 하드 드라이브의 설치 및 분리 절차는 비슷합니다 . 3.5 인치 하드 드라이브의 교체 절차를 보여주는 예는 다음과 같습니다 . 하드 드라이브 보호물 분리 주의 : 적절한 시스템 냉각을 유지하려면 모든 빈 하드 드라이브 베이에 드라 이브 보호물을 설치해야 합니다 . 주 : 이 항목은 핫 스왑 가능 하드 드라이브가 있는 시스템에만 적용됩니다 . 1 하드 드라이브 보호물 전면을 잡아 드라이브 베이에서 분리될 때까지 당겨 밀어 꺼냅니다 . 그림 3-2 를 참조하십시오 . 그림 3-2. 하드 드라이브 보호물 분리 또는 설치 1 1 하드 드라이브 보호물 하드 드라이브 보호물 설치 하드 드라이브 보호물을 드라이브 베이에 맞춘 다음 고정 래치가 제자리에 고정될 때까지 보호물을 드라이브 베이에 밀어 넣습니다 . 그림 3-2 를 참 조하십시오 .
하드 드라이브 캐리어 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 잠금 레버가 잠금 해제 기호를 가르킬 때까지 시계 반대 방향으로 돌립 니다 . 2 분리 단추를 밀어 분리 핸들을 엽니다 . 그림 3-3 을 참조하십시오 . 3 분리 핸들을 사용해 , 하드 드라이브 캐리어를 하드 드라이브 베이에서 당겨 꺼냅니다 . 주의 : 적절한 시스템 냉각을 유지하려면 모든 빈 하드 드라이브 베이에 드라 이브 보호물을 설치해야 합니다 . 그림 3-3.
하드 드라이브 캐리어 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 하드 드라이브 캐리어의 레버를 사용해 , 하드 드라이브 캐리어를 열고 하드 드라이브 캐리어가 후면판과 만나도록 드라이브 베이로 밀어 넣 습니다 . 그림 3-3 을 참조하십시오 . 2 분리 핸들을 닫아 하드 드라이브를 제자리에 고정합니다 . 3 잠금 레버를 잠금 기호를 가르키도록 시계 방향으로 돌립니다 . 그림 3-3 을 참조하십시오 . 하드 드라이브 캐리어에서 하드 드라이브 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 .
그림 3-4. 드라이브 캐리어에서 하드 드라이브 분리 및 설치 1 2 3 1 하드 드라이브 3 하드 드라이브 캐리어 2 나사 (4) 하드 드라이브 캐리어에 하드 드라이브 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 56 1 하드 드라이브 캐리어에 하드 드라이브를 놓습니다 . 그림 3-4 를 참조하 십시오 . 2 나사 4 개를 사용해 하드 드라이브를 하드 드라이브 캐리어에 고정합니 다 . 그림 3-4 를 참조하십시오 .
전원 공급 장치 전원 공급 장치 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주의 : 시스템이 정상적으로 작동하려면 하나의 전원 공급 장치가 있어야 합 니다 . 1 시스템과 시스템에 장착된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다 . 2 전원 케이블을 전원 및 전원 공급 장치에서 분리합니다 . 3 분리 레버를 누르고 핸들을 사용해 시스템에서 전원 공급 장치를 밀어 꺼냅니다 . 그림 3-5 를 참조하십시오 . 주 : 전원 공급 장치 분리에는 상당한 힘이 필요할 수도 있습니다 . 그림 3-5.
전원 공급 장치 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주의 : 시스템이 정상적으로 작동하려면 하나의 전원 공급 장치가 있어야 합 니다 . 1 두 전원 공급 장치의 유형과 최대 출력 전원이 동일한지 확인합니다 . 주 : 최대 출력 전원인 전원 공급 장치 레이블에 인쇄되어 있습니다 . 2 분리 래치가 제자리에 장착되어 전원 공급 장치가 완전히 고정될 때까 지 새 전원 공급 장치를 섀시에 밀어 넣습니다 . 그림 3-5 를 참조하십시 오. 3 전원 케이블을 전원 공급 장치에 연결하고 케이블을 전원 콘센트에 연 결합니다 .
그림 3-6. 시스템 보드 조립품 분리 및 설치 1 2 4 3 1 고정 래치 2 나사 3 핸들 4 시스템 보드 조립품 시스템 보드 조립품 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 보드 조립품이 제자리에 끼어질 때까지 섀시에 밀어 넣습니다 . 그림 3-6 을 참조하십시오 . 2 고정 래치를 고정하는 나사를 장착합니다 . 그림 3-6 을 참조하십시오 . 3 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 모두 켜십시오 .
냉각 덮개 냉각 덮개 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 냉각 덮개 한쪽을 화살표 방향으로 밀어 분리합니다. 그림 3-7을 참조하 십시오 . 4 냉각 덮개를 시스템 보드 조립품에서 살짝 들어올립니다 . 그림 3-7을 참 조하십시오 . 그림 3-7.
냉각 덮개 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 냉각 덮개를 맞추어 시스템 보드에 눌러 넣습니다. 그림 3-7을 참조하십 시오 . 2 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 3 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 모두 켜십시오 . 1 방열판 방열판 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 .
그림 3-8.
방열판 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받 을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 깨끗하고 보풀이 없는 천을 사용하여 방열판에 묻어 있는 열 그리즈를 닦아냅니다 . 2 새 프로세서 중앙 상단에 새 열 그리즈를 고르게 바릅니다 . 주의 : 열 그리즈를 지나치게 많이 사용하면 프로세서 실드에 묻어 프로세서 소켓의 오염을 일으킬 수 있습니다 . 3 방열판을 프로세서에 놓습니다 . 그림 3-8 을 참조하십시오 . 4 십자 드라이버를 사용하여 방열판 고정 나사 4 개를 조입니다 . 5 냉각 덮개를 다시 장착합니다. 60페이지의 "냉각 덮개 분리"를 참조하십 시오 .
주의 : 강한 힘으로 프로세서를 해당 소켓에 고정해야 합니다 . 단단히 잡지 않으면 분리 레버가 갑자기 튕겨 나올 수 있습니다 . 5 엄지 손가락을 프로세서 소켓 분리 레버 위에 단단히 놓은 후 레버를 잠 금 위치에서 분리합니다 . 프로세서가 소켓에서 분리될 때까지 레버를 90 도 각도로 위로 돌립니다 . 그림 3-9 를 참조하십시오 . 6 프로세서 실드를 위로 돌려 꺼냅니다 . 그림 3-9 를 참조하십시오 . 7 프로세서를 소켓에서 들어 꺼내고 소켓 분리 레버를 위로 올린 상태로 두어 소켓에 새 프로세서를 설치할 수 있도록 준비합니다 . 주의 : 프로세서를 분리할 때 ZIF 소켓의 핀이 구부러지지 않도록 주의하십시 오 . 핀이 구부러지면 시스템 보드가 영구적으로 손상될 수 있습니다 . 그림 3-9.
프로세서 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주 : 단 한개의 프로세서만 설치하는 경우 , 해당 프로세서는 반드시 프로세서 0 소켓에 설치해야 합니다 ( 소켓 위치의 경우 , 125 페이지의 " 시스템 보드 커 넥터 " 를 참조하십시오 ). 주 : 프로세서를 업그레이드할 경우 해당 시스템을 업그레이드하기에 앞서 support.dell.com 에서 최신 시스템 BIOS 버전을 설치합니다 . 다운로드한 파일 에 포함된 지침에 따라 해당 시스템의 업데이트를 설치합니다 . 1 사용한 적이 없는 프로세서인 경우에는 포장을 풉니다 .
10 냉각 덮개를 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십시오. 11 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 12 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 . 13 키를 눌러 시스템 설치 프로그램을 시작하고 프로세서 정보가 새 로운 시스템 구성과 일치하는지 확인합니다 . 34 페이지의 " 부팅에서 시스템 설치 옵션 " 을 참조하십시오 . 확장 카드 조립품 및 확장 카드 확장 카드 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 .
그림 3-10. 확장 카드 조립품 분리 1 2 1 나사 (5) 6 확장 카드를 고정하는 나사를 분리합니다 . 2 확장 카드 조립품 그림 3-11.
7 확장 카드의 모서리를 잡고 조심스럽게 확장 카드 커넥터에서 분리합 니다 . 8 카드를 영구적으로 분리하는 경우 , 빈 확장 슬롯 입구에 금속 필러 브래 킷을 설치한 다음 확장 카드 래치를 닫습니다 . 주 : 시스템의 미국 연방 통신위원회 (FCC) 인증을 유지하려면 필러 브래 킷을 빈 확장 슬롯에 설치해야 합니다 . 브래킷은 또한 시스템 안으로 먼 지 및 이물질이 들어오는 것을 막고 시스템 내부의 적절한 냉각 및 공기 흐름을 도와줍니다 . 확장 카드 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 .
8 필러 브래킷의 모서리를 잡고 조심스럽게 확장 카드 커넥터에서 분리 합니다 . 주 : 확장 카드를 분리해야 할 경우 사용할 수 있도록 이 브래킷을 보관해 둡니다 . 시스템의 FCC 인증을 유지하려면 필러 브래킷을 빈 확장 카드 슬롯에 설치해야 합니다 . 브래킷은 또한 시스템 안으로 먼지 및 이물질 이 들어오는 것을 막고 시스템 내부의 적절한 냉각 및 공기 흐름을 도와 줍니다 . 9 카드의 모서리를 잡고 카드 에지 커넥터가 확장 카드 조립품의 확장 카 드 커넥터에 맞춰지도록 카드를 놓습니다 . 10 카드가 완전히 장착될 때까지 카드 에지 커넥터를 확장 카드 커넥터에 단단히 삽입합니다 . 11 확장 카드를 고정하는 나사를 장착합니다 . 12 확장 카드 조립품을 시스템 보드 조립품에 놓습니다 . 13 확장 카드 조립품을 고정하는 나사 5 개를 장착합니다 . 14 냉각 덮개를 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십시오. 15 시스템 보드 조립품을 장착합니다 .
4 확장 카드 커넥터를 확장 카드 브래킷에 고정하는 나사 2 개를 분리합니 다 . 그림 3-12 를 참조하십시오 . 5 확장 카드 커넥터를 확장 카드 브래킷에서 잡아 당깁니다 . 그림 3-12 를 참조하십시오 . 그림 3-12.
확장 카드 커넥터 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 확장 카드 커넥터를 확장 카드 브래킷에 놓습니다 . 그림 3-12 를 참조하 십시오 . 2 확장 카드 커넥터를 확장 카드 브래킷에 고정하는 나사 2 개를 장착합니 다 . 그림 3-12 를 참조하십시오 . 3 확장 카드를 설치합니다. 68페이지의 "확장 카드 설치"를 참조하십시오. 4 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 5 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 .
그림 3-13. 메자닌 카드 분리 및 설치 1 2 1 나사 (3) 2 메자닌 카드 메자닌 카드 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 메자닌 카드를 시스템 보드 조림품에 놓습니다. 그림 3-13 및 그림 5-8을 참조하십시오 . 2 메자닌 카드를 고정하는 나사 3 개를 장착합니다 . 그림 3-13 을 참조하십 시오 . 3 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 4 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 .
지원되는 DIMM 구성 DIMM 소켓 12 개의 순서는 그림 3-14 를 참조하십시오 . DIMM 을 삽입하 면 , 항상 DIMM0_CHA 로 시작합니다 . 가능한 메모리 구성에 대해서는 표 3-1 을 참조하십시오 . 그림 3-14.
표 3-1. 메모리 모듈 구성 DIMM DIMM0 DIMM1 DIMM0 DIMM1 DIMM0 DIMM1 프로세서 0 CH A CH B CH C 1 – – – – – 4 – – – – 6 – – – 12 프로세서 1 CH A CH B CH C 1 – – – – – – 4 – – – – 6 – – – 12 주 : 빈 DIMM 소켓은 "_" 로 표시되어 있습니다 . 성능을 최적화하려면 설치된 모든 메모리 모듈은 동일한 제조업체 제품으로 , 속도 , 용량이 반드시 동일해 야 합니다 . 메모리 모듈 설치 경고 : 시스템의 전원을 끈 후 메모리 모듈은 뜨거우므로 일정한 시간 동안 건 드리지 마십시오 . 메모리 모듈을 다루기 전에 냉각될 때까지 기다립니다 .
1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 냉각 덮개를 분리합니다. 60페이지의 "냉각 덮개 분리"를 참조하십시오. 4 메모리 모듈 소켓을 찾습니다 . 그림 3-14 를 참조하십시오 . 5 메모리 모듈을 소켓에 삽입하려면 그림 3-15 에서 설명한 대로 메모리 모듈 소켓의 배출기를 아래로 누른 다음 밖으로 당깁니다 . 6 메모리 모듈의 중간 부분을 건드리지 않도록 주의하면서 모듈의 양쪽 카드 모서리만 잡습니다 . 7 메모리 모듈의 에지 커넥터를 메모리 모듈 소켓의 맞춤 키에 맞추고 메 모리 모듈을 소켓에 삽입합니다 . 그림 3-15 를 참조하십시오 . 주 : 메모리 모듈 소켓에는 메모리 모듈을 한 방향으로만 소켓에 설치하도록 하는 맞춤 키가 있습니다 . 그림 3-15.
8 엄지손가락으로 메모리 모듈을 눌러 메모리 모듈을 소켓에 고정합니 다 . 그림 3-15 를 참조하십시오 . 메모리 모듈이 소켓에 올바르게 장착된 경우 메모리 모듈 소켓의 배출 기는 메모리 모듈이 설치된 다른 소켓의 배출기와 맞춰집니다 . 9 이 절차 5 단계 ~ 8 단계 를 반복해 승인된 구성의 나머지 메모리 모듈을 설치합니다 . 표 3-1 을 참조하십시오 . 10 냉각 덮개를 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십시오. 11 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 12 시스템을 시작하고 키를 눌러 시스템 설치 프로그램을 시작한 다 음 기본 System Setup ( 시스템 설치 ) 화면에서 System Memory ( 시스 템 메모리 ) 설정을 확인합니다 . 새로 설치된 메모리를 반영하도록 이미 설정값이 변경되어 있어야 합 니다 .
5 메모리 모듈이 소켓에서 튕겨 나올 때까지 소켓 양쪽 끝의 배출기를 아 래로 누른 다음 밖으로 당깁니다 . 그림 3-15 를 참조하십시오 . 메모리 모듈의 중간 부분을 건드리지 않도록 주의하면서 각 메모리 모 듈의 양쪽 카드 모서리만 잡습니다 . 6 냉각 덮개를 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십시오. 7 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 8 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 모두 켭니다 . 접속기 확장기 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 .
그림 3-16. 접속기 확장기 분리 및 설치 1 2 3 1 나사 (5) 3 접속기 확장기 2 접속기 확장기 트레이 접속기 확장기 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 78 1 접속기 확장기를 접속기 확장기 트레이에 놓습니다 . 2 접속기 확장기를 접속기 확장기 트레이에 고정하는 나사 5 개를 장착합 니다 . 3 모든 케이블을 접속기 확장기에 연결합니다 . 그림 5-7 을 참조하십시오 . 4 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 .
시스템 배터리 시스템 배터리 교체 경고 : 새 배터리를 올바르게 설치하지 않으면 배터리가 파열될 위험이 있습 니다 . 제조업체에서 권장하는 것과 동일하거나 동등한 종류의 배터리로만 교 체합니다 . 자세한 내용은 해당 안전 정보를 참조하십시오 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템과 시스템에 장착된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 그림 3-17.
3 배터리 소켓을 찾습니다 . 125 페이지의 " 시스템 보드 커넥터 " 를 참조하 십시오 . 주의 : 배터리 커넥터의 손상을 방지하려면 배터리를 설치하거나 분리할 때 커넥터를 단단히 잡아야 합니다 . 4 배터리 위의 고정 클립을 커넥터의 양극 방향으로 부드럽게 당겨 배터 리를 커넥터에서 들어 꺼냅니다 . 그림 3-17 을 참조하십시오 . 5 "+" 가 배터리 커넥터의 고정 클립을 향하도록 새 배터리를 잡으십시 오 . 그림 3-17 을 참조하십시오 . 6 고정 클립이 제자리에 끼워질 때까지 고정 클립을 커넥터의 양극 방향 으로 부드럽게 당깁니다 . 그림 3-17 를 참조하십시오 . 7 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 8 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 모두 켭니다 . 9 배터리가 올바르게 작동하는지 확인하려면 시스템 설치 프로그램을 시 작합니다 .
2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 RAID 배터리 케이블을 PERC 카드의 커넥터에서 분리하려면 , RAID 배 터리 케이블 커넥터의 탭을 누른 다음 조심스럽게 PERC 카드의 커넥터 로부터 케이블 커넥터를 당깁니다 . 4 RAID 배터리 래치를 누르고 RAID 배터리를 들어 RAID 배터리 캐리어 에서 분리합니다 . 그림 3-18 을 참조하십시오 . 5 RAID 배터리를 RAID 배터리 캐리어에서 밀어 올려 꺼냅니다 . 그림 3-18 을 참조하십시오 . 그림 3-18. RAID 배터리 분리 및 설치 5 4 2 3 1 접속기 확장기 2 RAID 배터리 3 RAID 배터리 캐리어 4 RAID 배터리 래치 5 시스템 보드 조립품 1 RAID 배터리 설치 1 RAID 배터리 래치가 제자리에 고정될 때까지 RAID 배터리를 배터리 캐리어에 삽입합니다 . 그림 3-18 을 참조하십시오 .
3 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 4 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 모두 켭니다 . RAID 배터리 캐리어 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주 : 이 항목의 내용은 선택 사양인 RAID 컨트롤러 카드를 사용하는 시스템에 만 적용됩니다 . 82 1 시스템과 시스템에 장착된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다 . 2 시스템 보드 조립품을 분리합니다 .
그림 3-19. RAID 배터리 캐리어 분리 및 설치 3 1 접속기 확장기 3 시스템 보드 조립품 2 1 2 RAID 배터리 캐리어 RAID 배터리 캐리어 설치 1 RAID 배터리 캐리어를 접속기 확장기의 제자리에 놓습니다 . 그림 3-19 를 참조하십시오 . 2 RAID 배터리 캐리어를 접속기 확장기에 고정하는 나사를 장착합니다 . 그림 3-19 를 참조하십시오 . 3 RAID 배터리 캐리어에 RAID 배터리를 설치하십시오 . 81 페이지의 "RAID 배터리 설치 " 를 참조하십시오 . 4 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 5 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 모두 켭니다 .
시스템 보드 시스템 보드 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 냉각 덮개를 분리합니다. 60페이지의 "냉각 덮개 분리"를 참조하십시오. 4 방열판을 분리합니다 . 61 페이지의 " 방열판 분리 " 를 참조하십시오 . 5 확장 카드 조립품을 분리합니다. 66페이지의 "확장 카드 분리"를 참조하 십시오 .
그림 3-20. 시스템 보드 분리 및 설치 1 3 2 1 나사 (8) 3 시스템 보드 조립품 2 시스템 보드 시스템 보드 설치 1 새 시스템 보드의 포장을 풉니다 . 2 시스템 보드의 모서리를 잡고 시스템 보드를 시스템 보드 조립품에 밉 니다 . 3 나사 8 개를 장착하여 시스템 보드를 조립품에 고정합니다 . 4 프로세서를 새 시스템 보드로 이동합니다. 63페이지의 "프로세서 분리" 및 65 페이지의 " 프로세서 설치 " 를 참조하십시오 . 5 냉각 덮개를 다시 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십 시오 . 6 메모리 모듈을 분리하여 새 보드의 동일한 위치로 이동합니다 . 76 페이 지의 " 메모리 모듈 분리 " 및 74 페이지의 " 메모리 모듈 설치 " 를 참조 하십시오 . 7 시스템 보드에 하드 드라이브 및 전원 케이블을 연결합니다 .
8 해당하는 경우 메자닌 카드를 설치합니다 . 72 페이지의 " 메자닌 카드 설 치 " 를 참조하십시오 . 9 확장 카드 조립품을 설치합니다. 68페이지의 "확장 카드 설치"를 참조하 십시오 . 10 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 11 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 . 시스템 열기 및 닫기 경고 : 시스템을 옮겨야 하는 경우에는 반드시 다른 사람의 도움을 받으십시 오 . 부상당할 우려가 있으므로 시스템을 혼자 들지 마십시오 . 주의 : 올바른 냉각을 위해 본 시스템은 반드시 시스템 덮개가 설치된 상태에 서 작동해야 합니다 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 .
그림 3-21. 시스템 열기 및 닫기 1 3 2 4 1 트랙션 패드 2 시스템 덮개 3 덮개 분리 래치 잠금 장치 4 고정 나사 시스템 닫기 1 덮개를 섀시 위에 놓고 제자리에 끼워질 때까지 섀시 전면으로 밉니다 . 그림 3-21 을 참조하십시오 . 2 고정 나사로 덮개를 고정하십시오 . 그림 3-21 을 참조하십시오 . 냉각 팬 냉각 팬 분리 경고 : 냉각 팬이 없는 상태로 시스템을 작동하지 마십시오 . 경고 : 시스템의 전원을 끈 후에도 냉각 팬이 잠시 동안 계속 회전할 수 있습 니다 . 팬을 시스템에서 분리하기 전에 팬이 회전을 멈출 때까지 기다립니다 .
주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다 . 2 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 3 팬 컨트롤러 보드에서 팬의 전원 케이블을 분리합니다 . 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 . 이러한 케이블을 장착할 때 조이거나 구겨지지 않도록 적절하게 배선해야 합니다 . 4 팬을 냉각 팬 케이지에서 들어 꺼냅니다 . 그림 3-22.
냉각 팬 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 냉각 팬을 맞추고 냉각 팬이 단단히 장착될 때까지 냉각 팬 케이지로 밉 니다 . 그림 3-22 를 참조하십시오 . 주 : 팬 블레이드는 시스템의 전면 패널을 향해야 합니다 . 2 팬의 전원 케이블을 팬 컨트롤러 보드의 커넥터에 연결합니다 . 케이블이 조이거나 구겨지지 않도록 시스템 섀시의 탭을 통해 케이블 을 제대로 배선해야 합니다 . 3 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참조하십시오 .
시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 . 이러한 케이블을 장착할 때 조이거나 구겨지지 않도록 적절하게 배선해야 합니다 . 5 첫 번째 배전 보드를 시스템에 고정하는 나사를 분리합니다 . 그림 3-23 을 참조하십시오 . 6 섀시에서 배전 보드를 들어 꺼냅니다 . 그림 3-23 을 참조하십시오 . 주 : 첫 번째 배전 보드 아래에 있는 두 번째 배전 보드를 분리하려면 , 배 전 보드 커넥터를 분리하고 들어 올리기 전에 보드의 각도를 맞춥니다 . 그림 3-23.
배전 보드 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주의 : 분리한 경우 , 상단의 첫 번째 배전 보드를 장착하기 전에 하단의 두 번 째 배전 보드 및 배전 보드 커넥터를 반드시 장착해야 합니다 . 1 분리한 경우 , 우선 시스템에 첫 번째 배전 보드를 놓아야 합니다 . 그림 3-23 을 참조하십시오 . 그렇지 않은 경우 , 5 단계로 건너뛰십시오 . 주 : 첫 번재 배전 보드 아래에 있는 두 번째 배전 보드를 설치하려면 , 설 치 과정에서 보드의 각도를 맞춥니다 . 2 두 번째 배전 보드를 시스템에 고정하는 나사를 분리합니다 .
팬 컨트롤러 보드 팬 컨트롤러 보드 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다 . 2 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 3 배전 보드를 분리합니다. 89페이지의 "배전 보드 분리"를 참조하십시오. 4 팬 컨트롤러 보드에서 모든 케이블을 분리합니다 . 그림 5-9 를 참조하십 시오 . 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 .
그림 3-24. 팬 컨트롤러 보드 분리 및 설치 1 1 팬 컨트롤러 보드 2 2 나사 팬 컨트롤러 보드 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 팬 컨트롤러 보드를 섀시에 놓고 제자리에 밀어 넣습니다 . 그림 3-24 를 참조하십시오 . 2 팬 컨트롤러 보드를 섀시에 고정하는 나사를 장착합니다 . 그림 3-24 를 참조하십시오 . 3 팬 컨트롤러 보드에 모든 케이블을 연결합니다 . 그림 5-9 를 참조하십시 오. 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 4 배전 보드를 장착합니다.
5 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참조하십시오 . 6 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 . 중앙판 중앙판 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 94 1 시스템 및 시스템에 장착된 모든 주변 장치의 전원을 끄고 시스템을 전 원 콘센트에서 분리합니다 . 2 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 3 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 .
그림 3-25. 냉각 팬 브래킷 분리 및 설치 1 2 3 1 냉각 팬 브래킷 ( 김 ) 3 냉각 팬 브래킷 ( 짧음 ) 7 상단 중앙판을 중앙판 홀더에 고정하는 나사를 분리합니다 . 그림 3-26 을 참조하십시오 . 8 모든 케이블을 상단 중앙판에서 분리합니다 . 그림 5-7 을 참조하십시오 . 2 나사 (14) 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 . 이러한 케이블을 장착할 때 조이거나 구겨지지 않도록 적절하게 배선해야 합니다 . 9 상단 중앙판을 들어 꺼냅니다 . 그림 3-26 을 참조하십시오 .
그림 3-26. 상단 중앙판 분리 및 설치 1 2 96 1 나사 (9) 10 중앙판 홀더 지지대를 섀시에 고정하는 나사를 분리합니다 . 그림 3-27 을 참조하십시오 . 11 중앙판 홀더 지지대를 섀시에서 들어 꺼냅니다 . 그림 3-27 을 참조하십 시오 .
그림 3-27. 중앙판 홀더 지지대 분리 및 설치 2 1 1 나사 (4) 12 중앙판 홀더를 섀시에 고정하는 나사를 분리합니다 . 그림 3-28 을 참조 하십시오 . 13 중앙판 홀더를 섀시에서 들어 꺼냅니다 . 그림 3-28 을 참조하십시오 .
그림 3-28. 중앙판 홀더 분리 및 설치 1 2 1 나사 (8) 14 하단 중앙판을 섀시에 고정하는 나사를 분리합니다 . 그림 3-29 를 참조 하십시오 . 15 모든 케이블을 하단 중앙판에서 분리합니다 . 그림 5-7 을 참조하십시오 . 2 중앙판 홀더 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 . 이러한 케이블을 장착할 때 조이거나 구겨지지 않도록 적절하게 배선해야 합니다 . 16 98 하단 중앙판을 섀시에서 들어 꺼냅니다 . 그림 3-29 를 참조하십시오 .
그림 3-29. 하단 중앙판 분리 및 설치 1 2 1 나사 (8) 2 하단 중앙판 중앙판 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 하단 중앙판을 섀시에 놓습니다 . 그림 3-29 를 참조하십시오 . 2 하단 중앙판을 섀시에 고정하는 나사를 장착합니다 . 그림 3-29 를 참조 하십시오 . 3 모든 케이블을 하단 중앙판에 연결합니다 . 그림 5-7 을 참조하십시오 . 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 4 중앙판 홀더를 섀시에 놓습니다 . 그림 3-28 을 참조하십시오 .
7 중앙판 홀더 지지대를 섀시에 고정하는 나사를 장착합니다 . 그림 3-27 을 참조하십시오 . 8 상단 중앙판을 중앙판 홀더에 놓습니다 . 그림 3-26 을 참조하십시오 . 9 중앙판을 중앙판 홀더에 고정하는 나사를 장착합니다 . 그림 3-26 을 참 조하십시오 . 10 모든 케이블을 상단 중앙판에 연결합니다 . 그림 5-7 을 참조하십시오 . 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 11 팬 브래킷을 섀시에 놓습니다 . 그림 3-25 를 참조하십시오 . 12 팬 브래킷을 섀시에 고정하는 나사를 장착합니다 . 그림 3-25 를 참조하 십시오 . 13 냉각 팬을 장착합니다 . 89 페이지의 " 냉각 팬 설치 " 를 참조하십시오 . 14 시스템 보드 조립품을 장착합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 15 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참조하십시오 .
3 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 주의 : 드라이브 및 후면판의 손상을 방지하려면 후면판을 분리하기 전에 시 스템에서 하드 드라이브를 분리해야 합니다 . 주의 : 하드 드라이브를 동일한 위치에 장착할 수 있도록 분리하기 전에 각 하 드 드라이브의 번호를 기록하고 임시적으로 레이블을 붙여야 합니다 . 4 하드 드라이브 케이지를 섀시에 고정하는 나사를 분리합니다 . 그림 3-30 을 참조하십시오 . 그림 3-30. 후면판 분리 및 설치 1 2 1 하드 드라이브 케이지 5 전면 패널 조립품을 섀시에 고정하는 나사를 분리합니다 . 그림 3-31 를 참조하십시오 . 6 후면판에서 모든 케이블을 분리하십시오 . 3.5 인치 하드 드라이브는 그림 5-3 을 참조하고 2.5 인치 하드 드라이브는 그림 5-5 를 참조하십 시오 . 2 나사 (10) 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 .
7 팬 컨트롤러 보드에서 전면 패널 케이블을 분리합니다. 그림 5-9를 참조 하십시오 . 시스템에서 케이블을 분리할 때 섀시 탭 아래 케이블 배선에 주의하십 시오 . 이러한 케이블을 장착할 때 조이거나 구겨지지 않도록 적절하게 배선해야 합니다 . 8 섀시에서 하드 디스크 드라이브 케이지를 분리하십시오 . 그림 3-31 을 참조하십시오 . 그림 3-31. 하드 드라이브 케이지 분리 및 설치 1 2 102 1 하드 드라이브 케이지 9 후면판을 하드 드라이브 케이지에 고정하는 나사를 분리합니다 . 그림 3-32 를 참조하십시오 . 10 하드 드라이브 케이지에서 후면판을 분리합니다. 그림 3-32를 참조하십 시오 .
그림 3-32. 하드 드라이브 케이지에서 후면판 분리 및 설치 1 2 3 1 하드 드라이브 케이지 3 나사 (10 개 ) 2 후면판 후면판 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 2 3 4 5 후면판을 하드 드라이브 케이지에 설치합니다. 그림 3-32를 참조하십시 오. 후면판을 하드 드라이브 케이지에 고정하는 나사를 장착합니다 . 그림 3-32 를 참조하십시오 . 하드 드라이브 케이지를 섀시에 장착합니다 . 그림 3-31 을 참조하십시 오. 전면 패널 조립품을 섀시에 고정하는 나사를 장착합니다 . 그림 3-31 을 참조하십시오 .
6 팬 컨트롤러 보드에 전면 패널 케이블을 연결합니다. 그림 5-9를 참조하 십시오 . 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 하드 드라이브 케이지를 고정하는 나사를 장착합니다 . 그림 3-30 을 참 조하십시오 . 8 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참조하십시오 . 9 하드 드라이브를 장착합니다 . 56 페이지의 " 하드 드라이브 캐리어에 하 드 드라이브 설치 " 를 참조하십시오 . 10 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 . 7 전면 패널 전면 패널 분리 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 .
6 하드 드라이브 케이지를 섀시에 고정하는 나사를 분리합니다 . 그림 3-30 을 참조하십시오 . 7 전면 패널 조립품을 섀시에 고정하는 나사를 분리합니다 . 그림 3-31 을 참조하십시오 . 8 섀시에서 하드 디스크 드라이브 케이지를 분리하십시오 . 그림 3-31 을 참조하십시오 . 9 전면 패널 조립품을 하드 드라이브 케이지에 고정하는 나사를 분리합 니다 . 그림 3-33 을 참조하십시오 . 10 전면 패널 조립품을 하드 드라이브 케이지에서 분리합니다 . 그림 3-33 을 참조하십시오 . 그림 3-33. 전면 패널 조립품 분리 및 설치 2 1 1 전면 패널 조립품 11 전면 패널 조립품의 고정 고리를 남겨 둡니다 . 그림 3-34 를 참조하십시 오. 12 전면 패널 조립품에서 전면 패널을 분리합니다 . 그림 3-34 를 참조하십 시오 .
그림 3-34. 전면 패널 분리 및 설치 1 2 3 1 전면 패널 조립품 3 고정 고리 2 전면 패널 전면 패널 설치 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 106 1 전면 패널 조립품의 고정 고리를 남겨두고 전면 패널을 전면 패널 조립 품에 놓습니다 . 그림 3-34 를 참조하십시오 . 2 전면 패널 조립품을 하드 드라이브 케이지에 장착합니다 . 그림 3-33 을 참조하십시오 . 3 전면 패널 조립품을 하드 드라이브 케이지에 고정하는 나사를 장착합 니다 . 그림 3-33 을 참조하십시오 .
6 하드 드라이브 케이지를 섀시에 고정하는 나사를 장착합니다 . 그림 3-30 을 참조하십시오 . 7 팬 컨트롤러 보드에 전면 패널 케이블을 연결합니다. 그림 5-9를 참조하 십시오 . 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 8 케이블을 모두 후면판에 연결합니다. 3.5인치 하드 드라이브는 그림 5-3 을 참조하고 2.5 인치 하드 드라이브는 그림 5-5 를 참조하십시오 . 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대 로 배선해야 합니다 . 9 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참조하십시오 . 10 하드 드라이브를 장착합니다 . 56 페이지의 " 하드 드라이브 캐리어에 하 드 드라이브 설치 " 를 참조하십시오 . 11 시스템을 전원 콘센트에 다시 연결하고 시스템과 시스템에 연결된 주 변장치의 전원을 켜십시오 .
시스템 구성요소 설치
시스템 문제 해결 안전 제일 - 사용자와 사용자 시스템의 안전을 위하여 경고 : 시스템을 옮겨야 하는 경우에는 반드시 다른 사람의 도움을 받으십시 오 . 부상당할 우려가 있으므로 시스템을 혼자 들지 마십시오 . 경고 : 시스템 덮개를 분리하기 전에 먼저 모든 전원을 분리하고 AC 전원 코 드를 분리한 다음 모든 주변 장치를 분리하고 모든 LAN 선을 분리합니다 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 설치 문제 설치 문제를 해결하려면 다음 사항을 확인하십시오 . • 모든 랙 케이블 연결을 포함하여 모든 케이블 및 전원 연결을 확인합 니다 .
시스템 시작 오류 문제 해결 특히 운영 체제를 설치한 후 또는 시스템 하드웨어를 구성한 후에 , 시스템 시 작 시 시스템이 멈추게 되면 , 메모리 구성에 이상이 있는지 확인하십시오 . 메모리 구성이 잘못된 경우 시스템 시작 시 비디오 출력 없이 작동이 중단될 수 있습니다 . 72 페이지의 " 시스템 메모리 " 를 참조하십시오 . 기타 모든 시작 문제는 화면에 표시되는 시스템 메시지를 참고하십시오 . 자 세한 내용은 33 페이지의 " 시스템 설치 프로그램 사용 " 을 참조하십시오 . 외부 연결 문제 해결 외부 장치의 문제를 해결하기 전에 모든 외부 케이블이 시스템의 외부 커 넥터에 제대로 연결되어 있는지 확인하십시오 . 시스템의 전면 및 후면 패 널 커넥터에 대한 내용은 그림 1-1, 그림 1-2 및 그림 1-5 를 참조하십시오 . 비디오 하위 시스템 문제 해결 1 모니터에 대한 시스템 및 전원 연결을 검사합니다 . 2 시스템과 모니터 사이의 비디오 인터페이스 케이블 연결을 검사합니다.
6 시스템을 재시작하고 키보드가 작동하는 경우 시스템 설치 프로그램을 시작합니다 . USB 포트가 모두 활성화되었는지 확인합니다 . 41 페이지 의 "USB 구성 " 을 참조하십시오 . 키보드가 작동하지 않는 경우 원격 액세스를 사용할 수도 있습니다 . 시 스템에 액세스할 수 없는 경우 134 페이지의 " 점퍼 설정 " 에서 해당 시 스템 내부의 NVRAM_CLR 점퍼 설정 및 BIOS 를 기본 설정으로 복원하 는 방법에 대한 지침을 참조하십시오 . 7 각 USB 장치를 하나씩 다시 연결하고 전원을 켭니다 . 8 장치에서 같은 문제가 발생하면 장치 전원을 끄고 USB 케이블을 교체 한 다음 장치 전원을 켭니다 . 문제가 지속되면 장치를 교체합니다 . 문제가 해결되지 않으면 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . 직렬 I/O 장치 문제 해결 1 시스템 및 직렬 포트에 연결된 모든 주변 장치를 끕니다 .
NIC 문제 해결 1 시스템을 재시작하고 NIC 컨트롤러와 관련된 시스템 메시지를 확인합 니다 . 2 NIC 커넥터에서 해당 표시등을 확인합니다 . 17 페이지의 "NIC 표시등 (KVM Over IP Port)" 을 참조하십시오 . • 링크 표시등이 켜지지 않는 경우 모든 케이블 연결을 검사합니다 . • 작동 표시등이 켜지지 않는 경우 네트워크 드라이버 파일이 손상되 었거나 없는 것일 수 있습니다 . 해당하는 경우 드라이버를 분리하고 다시 설치합니다 . NIC 설명서 를 참조하십시오 . • 가능한 경우 자동 협상 설정을 변경합니다 . • 스위치 또는 허브의 다른 커넥터를 사용합니다 . 내장형 NIC 카드가 아닌 다른 NIC 카드를 사용하는 경우 NIC 카드의 설명서를 참조하십시오 . 3 적절한 드라이버가 설치되어 있고 프로토콜이 연결되어 있는지 확인합 니다 . NIC 설명서를 참조하십시오 . 4 시스템 설치 프로그램을 시작하고 NIC 포트가 활성화되었는지 확인합 니다 .
습식 시스템 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다 . 2 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 3 시스템에서 구성요소를 분해합니다 . 51 페이지의 " 시스템 구성요소 설 치 " 를 참조하십시오 . • 냉각기 덮개 • 하드 드라이브 • SAS 후면판 • 확장 카드 • 전원 공급 장치 • 팬 • 프로세서 및 방열판 • 메모리 모듈 4 최소한 하루 정도 시스템을 완전히 건조시킵니다 .
손상된 시스템 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다 . 2 시스템을 엽니다 . 86 페이지의 " 시스템 열기 " 를 참조하십시오 . 3 다음 구성요소가 올바르게 설치되었는지 확인합니다 . • 확장 카드 조립품 • 전원 공급 장치 • 팬 • 프로세서 및 방열판 • 메모리 모듈 • 하드 드라이브 캐리어 • 냉각기 덮개 4 모든 케이블이 올바르게 연결되었는지 확인합니다 . 5 시스템을 닫습니다 .
4 시스템 설치 프로그램을 시작합니다 . 시스템 설치 프로그램의 시간 및 날짜가 정확하지 않은 경우 배터리를 교체합니다 . 79 페이지의 " 시스템 배터리 교체 " 를 참조하십시오 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 배터리를 교체해도 문제가 해결되지 않는 경우 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . 주 : 일부 소프트웨어는 시스템의 시간을 빠르게 하거나 늦출 수 있습니다 . 시스템이 올바르게 작동하지만 시스템 설치 프로그램에 유지된 시간이 정확 하지 않은 경우 문제는 불량 배터리가 아니라 소프트웨어로 인해 발생한 것일 수 있습니다 .
시스템 냉각 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 다음 상태 중 하나에 해당하지 않는지 확인합니다 . • 시스템 덮개 , 냉각기 덮개 , 드라이브 보호물 , 전원 공급 장치 보호물 , 전 면 또는 후면 필러 패널이 분리되었습니다 . • 주변 온도가 너무 높습니다 . • 외부 공기 흐름이 막혔습니다 . • 시스템 내부의 케이블이 공기 흐름을 막습니다 . • 개별 냉각 팬이 분리되었거나 오류가 발생했습니다 . 116 페이지의 " 팬 문제 해결 " 을 참조하십시오 .
7 시스템을 재시작합니다 . 문제가 해결되면 시스템을 닫습니다 . 87 페이지의 " 시스템 닫기 " 를 참 조하십시오 . 교체 팬이 작동하지 않으면 137 페이지의 " 도움말 얻기 " 를 참조하십 시오 . 시스템 메모리 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀 에서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니 다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주 : 메모리 구성이 잘못된 경우 시작 단계에서 어떠한 비디오도 출력되지 않 고 시스템이 중단될 수 있습니다 . 72 페이지의 " 시스템 메모리 " 를 참조하고 메모리 구성이 적용 가능한 모든 지침을 준수하는지 확인하십시오 .
8 메모리 모듈을 해당 소켓에 다시 장착합니다. 74페이지의 "메모리 모듈 설치 " 를 참조하십시오 . 9 냉각 덮개를 장착합니다. 61페이지의 "냉각 덮개 설치"를 참조하십시오. 10 시스템 보드 조립품을 설치합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 . 11 시스템을 전원 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치의 전원을 켭니다 . 12 시스템 설치 프로그램을 시작하고 시스템 메모리 설정을 확인합니다 . 36 페이지의 " 시스템 메모리 설정 " 을 참조하십시오 . 문제가 해결되지 않으면 다음 단계를 계속 진행합니다 . 13 시스템 및 장착된 주변 장치의 전원을 끄고 시스템에서 전원 연결을 분 리합니다 . 14 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 15 진단 검사나 오류 메시지가 특정 메모리 모듈에 오류가 있음을 나타내 면 이 모듈을 교환하거나 교체합니다 .
하드 드라이브 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 주의 : 이 문제 해결 절차로 인해 하드 드라이브에 저장된 데이터가 삭제될 수 있습니다 . 계속하기 전에 하드 드라이브에 있는 모든 파일을 백업합니다 . 1 시스템에 RAID 컨트롤러가 있고 하드 드라이브가 RAID 배열로 구성된 경우 다음 단계를 수행합니다 . a 시스템을 재시작하고 RAID 컨트롤러의 경우 키 조합 또는 SAS 컨트롤러의 경우 키 조합을 눌러 호스트 어 댑터 구성 유틸리티 프로그램을 시작합니다 .
저장소 컨트롤러 문제 해결 주 : SAS 또는 SAS RAID 컨트롤러의 문제를 해결하려면 운영 체제 및 컨트롤 러의 설명서도 함께 참조하십시오 . 1 시스템 설치 프로그램을 시작하여 SAS 컨트롤러가 활성화되었는지 확 인합니다 . 33 페이지의 " 시스템 설치 프로그램 사용 " 을 참조하십시오 . 2 시스템을 재시작하고 해당하는 키를 순차적으로 눌러 구성 유틸리티 프로그램을 시작합니다 . • SAS 컨트롤러의 경우 키 조합 • RAID 컨트롤러의 경우 키 조합 구성 설정에 대한 내용은 컨트롤러 설명서를 참조하십시오 . 3 구성 설정을 확인하여 필요한 수정을 하고 시스템을 재시작합니다 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 .
확장 카드 문제 해결 주 : 확장 카드의 문제를 해결하려면 운영 체제 및 확장 카드 설명서를 참조하 십시오 . 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 각 확장 카드가 해당 커넥터에 단단히 연결되었는지 확인합니다 . 68 페 이지의 " 확장 카드 설치 " 를 참조하십시오 . 4 시스템 보드 조립품을 설치합니다 .
프로세서 문제 해결 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 1 시스템 및 장착된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다 . 2 시스템 보드 조립품을 분리합니다 . 58 페이지의 " 시스템 보드 조립품 분 리 " 를 참조하십시오 . 3 각 프로세서 및 방열판이 올바르게 설치되었는지 확인합니다 . 65 페이 지의 " 프로세서 설치 " 를 참조하십시오 . 4 시스템 보드 조립품을 설치합니다 . 59 페이지의 " 시스템 보드 조립품 설 치 " 를 참조하십시오 .
14 9 단계 ~11 단계를 반복합니다 . 프로세서를 모두 검사했지만 문제가 지속되면 시스템 보드에 오류가 있는 것입니다 . 137 페이지의 " 도움말 얻기 " 를 참조하십시오 . IRQ 할당 충돌 대부분 PCI 장치는 다른 장치와 함께 IRQ 를 공유할 수 있지만 동시에 하 나의 IRQ 를 사용할 수는 없습니다 . 이러한 유형의 충돌을 방지하려면 각 PCI 장치의 개별 IRQ 요구 사항에 대한 설명서를 참조하십시오 . 표 4-1.
시스템 문제 해결
점퍼 및 커넥터 시스템 보드 커넥터 이 항목에서는 시스템 점퍼에 대한 자세한 정보를 제공합니다 . 또한 점퍼 및 스위치에 대한 기본 정보를 제공하며 시스템의 다양한 보드에 있는 커 넥터에 대해 설명합니다 . 그림 5-1.
17 확장 슬롯 18 BMC 디버그 커넥터 19 전원 단추 20 VGA 포트 21 직렬 포트 22 KVM over IP 포트 23 NIC2 커넥터 (RJ45) 24 NIC1 커넥터 (RJ45) 25 ID LED 26 USB 포트 후면판 커넥터 3.5 인치 드라이브 그림 5-2. 후면판 전면 패널 — 3.5 인치 드라이브 1 126 2 3 4 1 3.
그림 5-3. 후면판 후면 패널 — 3.
2.5 인치 드라이브 그림 5-4. 후면판 전면 패널 — 2.5 인치 드라이브 1 5 3 4 1 시스템 보드 1 용 SATA2 및 SAS 커넥터 1 ~ 6 ( 왼쪽 ~ 오른쪽 ) 2 시스템 보드 3 용 SATA2 및 SAS 커넥터 1 ~ 6 ( 왼쪽 ~ 오른쪽 ) 3 시스템 보드 4 용 SATA2 및 SAS 커넥터 1 ~ 6 ( 왼쪽 ~ 오른쪽 ) 4 시스템 보드 2 용 SATA2 및 SAS 커넥터 1 ~ 6 ( 왼쪽 ~ 오른쪽 ) 5 2.
그림 5-5. 후면판 후면 패널 — 2.
중앙판 커넥터 그림 5-6.
접속기 확장기 커넥터 그림 5-7.
메자닌 카드 커넥터 그림 5-8.
팬 컨트롤러 보드 커넥터 그림 5-9.
배전 보드 커넥터 그림 5-10. 배전 보드 커넥터 1 2 3 4 5 6 1 후면판 전원 커넥터 2 시스템 팬 보드 커넥터 3 시스템 보드 3 및 4 용 주 전 원 커넥터 4 시스템 보드 1 및 2 용 주 전 원 커넥터 5 시스템 팬 보드 전원 커넥터 6 브릿지 카드 커넥터 점퍼 설정 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 .
시스템 구성 점퍼 설정 각각의 시스템 보드에 설치된 시스템 구성 점퍼의 기능은 아래와 같습니다 : 그림 5-11. 시스템 구성 점퍼 1 2 1 A B A B C C D E D E Ữ㜆⇛ Disable 2 㜆⇛ e Enabl 표 5-1. 시스템 구성 점퍼 점퍼 기능 꺼짐 켜짐 A 디버그를 위해 ME 기능 비활성 * 비활성 활성 B BIOS PCI-E 설치용 예비 장치 - - C BIOS 삭제 암호 * 비활성 활성 D BIOS 삭제 CMOS * 비활성 활성 E 시스템 재설정 * 비활성 활성 주 : 시스템 구성 점퍼 표의 * 는 기본 상태를 나타내며 기본 상태는 활성 상태 가 아닙니다 .
후면판 점퍼 설정 주의 : 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다 . 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스 / 지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다 . Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다 . 제품과 함께 제공된 안전 지침을 읽고 따르십시오 . 3.5 인치 후면판 및 2.5 인치 후면판에 설치된 점퍼의 기능은 동일합니다 . 3.5 인치 후면판에 설치해 점퍼를 사용하는 예는 다음과 같습니다 . 그림 5-12. 후면판에 설치된 점퍼 㜆⇛ Enable Ữ㜆⇛ Disable 2 1 2 1 A B C D 표 5-2.
도움말 얻기 Dell 에 문의하기 미국에 거주하는 고객은 800-WWW-DELL (800-999-3355) 로 전화하십시오 . 주 : 인터넷 연결을 사용할 수 없는 경우에는 구매 송장 , 포장 명세서 , 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다 . Dell 은 다양한 온라인 및 전화 기반의 지원과 서비스 옵션을 제공합니다 . 제공 여부는 국가 / 지역과 제품에 따라 차이가 있으며 일부 서비스는 소재 지역에서 사용하지 못할 수 있습니다 . 판매 , 기술 지원 또는 고객 서비스 문제에 대해 Dell 에 문의하려면 : 1 support.dell.com 을 방문합니다 . 2 페이지 아래쪽의 Choose A Country/Region (국가/지역을 선택해 주세요) 드롭다운 메뉴에서 소재 국가 또는 지역이 있는지 확인합니다 . 3 페이지 왼쪽에서 Contact Us ( 문의처 ) 를 클릭합니다 . 4 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다 .
도움말 얻기
용어집 A — 암페어 (Ampere) 의 약어 . AC — 교류 전류 (Alternating Current) 의 약어 . ACPI — 고급 구성 및 전원 인터페이스 (Advanced Configuration and Power Interface) 의 약어 . 운영 체제가 구성 및 전원을 관리할 수 있도록 하는 표준 인터페 이스입니다 . ANSI — 미국 표준 협회 (American National Standards Institute) 의 약어 . 미국의 기술 표준을 수립하는 주요 기관입니다 . BMC — 베이스보드 관리 컨트롤러 (Baseboard Management Controller) 의 약어 . BTU — 영국식 열 단위 (British Thermal Unit) 의 약어 . C — 섭씨 (Celsius) 의 약어 . cm — 센티미터 (Centimeter) 의 약어 . COM n — 시스템 직렬 포트에 대한 장치 이름 .
ESD — 정전기 방전 (Electrostatic Discharge) 의 약어 . ESM — 내장형 서버 관리 (Embedded Server Management) 의 약어 . F — 화씨 (Fahrenheit) 의 약어 . FAT — 파일 할당표 (File Allocation Table) 의 약어 . 파일 시스템 구조는 MS-DOS 에서 파일 저장 공간을 구성하고 추적하는 데 사용합니다 . Microsoft® Windows® 운영 체제는 FAT 파일 시스템 구조를 선택적으로 사용할 수 있습니다 . FSB — 전면 버스 (Front-Side Bus) 의 약어 . FSB 는 프로세서와 주 메모리 (RAM) 간의 데이터 경로와 물리적 인터페이스입니다 . FTP — 파일 전송 프로토콜 (File Transfer Protocol) 의 약어 . g — 그램 (Gram) 의 약어 . G — 중력 (Gravity) 의 약어 .
Kbps — 초당 킬로비트 (Kilobit per second) 의 약어 . KBps — 초당 킬로바이트 (Kilobyte per second) 의 약어 . kg — 킬로그램 (Kilogram) 의 약어 , 1000 그램 . kHz — 킬로헤르츠 (Kilohertz) 의 약어 . KVM — 키보드 / 비디오 / 마우스 (Keyboard/Video/Mouse) 의 약어 . KVM 은 비디 오가 표시되고 키보드 및 마우스가 사용되는 시스템을 선택할 수 있도록 하는 스위 치를 나타냅니다 . LAN — LAN (Local Area Network) 의 약어 . LAN 은 일반적으로 같은 빌딩이나 인 접해 있는 몇 개의 빌딩에만 한정되며 , 모든 장치는 LAN 전용선으로 연결됩니다 . LCD — 액정 디스플레이 (Liquid Crystal Display) 의 약어 . LED — 발광 다이오드 (Light-Emitting Diode) 의 약어 . 전류가 흐르면 불이 켜지 는 전자 장치입니다 .
NIC — 네트워크 인터페이스 컨트롤러 (Network Interface Controller) 의 약어 . 네 트워크에 연결하기 위해 시스템에 설치 또는 내장된 장치입니다 . NMI — 마스크 불가능 인터럽트 (Nonmaskable Interrupt) 의 약어 . 하드웨어 오류 발생 시 NMI 신호를 프로세서에 전송하는 장치입니다 . ns — 나노초 (Nanosecond) 의 약어 . NVRAM — 비휘발성 임의 액세스 메모리 (Nonvolatile Random-Access Memory) 의 약어 . 시스템을 꺼도 메모리의 내용이 유실되지 않습니다 . NVRAM 은 날짜 , 시간 및 시스템 구성 정보를 유지하는 데 사용됩니다 . PCI — 주변 장치 구성요소 상호 연결 (Peripheral Component Interconnect) 의 약 어 . 로컬 버스를 구현하는 표준입니다 . PDB — 배전 보드입니다 .
SATA — 직렬 고급 기술 연결 (Serial Advanced Technology Attachment) 의 약어 . 시 스템 보드와 저장 장치 간의 표준 인터페이스 . SCSI — 소형 컴퓨터 시스템 인터페이스 (Small Computer System Interface) 의 약어 . 표준 포트보다 더 빠른 데이터 전송 속도를 제공하는 I/O 버스 인터페이스입니다 . SD 카드 — Secure Digital 플래시 메모리 카드 . SDRAM — 동기식 동적 임의 액세스 메모리 (Synchronous Dynamic RandomAccess Memory) 의 약어 . sec — 초 (Second) 의 약어 . SMART — 자체 모니터링 분석 및 보고 기술 (Self-Monitoring Analysis and Reporting Technology) 의 약어 . 하드 드라이브가 시스템 BIOS 에 오류나 결함을 보 고하면 오류 메시지가 화면에 나타나도록 합니다 .
VGA — 비디오 그래픽 배열 (Video Graphics Array) 의 약어 . VGA 와 SVGA 는 기 존의 표준보다 높은 해상도와 색상 표시 기능을 가진 비디오 어댑터의 비디오 표준 입니다 . W — 와트 (Watt) 의 약어 . WH — 시간당 와트 (Watt-Hour) 의 약어 . XML — 확장형 표기 언어 (Extensible Markup Language) 의 약어 . XML 은 일반적 인 정보 형식을 작성하고 World Wide Web, 인트라넷 등을 통해 형식 및 데이터를 공유하는 방법입니다 . ZIF — 영 삽입력 (Zero Insertion Force) 의 약어 . 가상화 — 소프트웨어를 통해 컴퓨터 한 대의 리소스를 여러 환경에서 공유하는 기 능 . 하나의 실제 시스템은 다양한 운영 체제를 호스트할 수 있는 여러 가상 시스템 으로 나타날 수 있습니다 . 그래픽 모드 — x ( 수평 픽셀 ) x y ( 수직 픽셀 ) x z ( 색상 ) 로 정의되는 비디오 모드 .
부팅 매체 — 시스템이 하드 드라이브에서 부팅되지 않은 경우 시스템을 시작하는 데 사용되는 CD, 디스켓 또는 USB 메모리 키 . 블레이드 — 프로세서 , 메모리 및 하드 드라이브가 포함된 모듈 . 모듈은 전원 공급 장치와 팬이 있는 섀시에 장착되어 있습니다 . 비디오 메모리 — 대부분의 VGA 와 SVGA 비디오 어댑터에는 시스템의 RAM 외에 메모리 칩이 들어 있습니다 . 비디오 드라이버와 모니터 기능이 적절한 경우 설치 되어 있는 비디오 메모리 양은 주로 프로그램이 표시할 수 있는 색상 수에 영향을 미칩니다 . 비디오 어댑터 — 모니터와 함께 시스템의 비디오 기능을 제공하는 논리 회로 . 비 디오 어댑터는 시스템 보드에 내장되거나 확장 슬롯에 꽂는 확장 카드의 형태일 수 있습니다 . 비디오 해상도 — 비디오 해상도 ( 예 : 800 x 600) 는 수평 방향 픽셀 수 x 수직 방향 픽셀 수로 표시됩니다 .
자산 태그 — 일반적으로 관리자가 보안이나 추적 목적으로 시스템에 할당하는 개 별 코드 . 장치 드라이버 — 운영 체제 또는 일부 다른 프로그램이 주변 장치와 올바르게 통 신할 수 있도록 하는 프로그램 . 점퍼 — 회로 보드에서 돌출된 2 개 이상의 핀이 있는 작은 블록 . 선이 들어 있는 플 라스틱 플러그를 핀 위에 끼워 넣습니다 . 배선은 핀을 연결하고 회로를 작성하며 보드의 회로를 변경할 수 있는 단순하고 전환 가능한 방법을 제공합니다 . 제어판 — 전원 단추 및 전원 표시등과 같은 표시등과 제어부가 있는 시스템의 일부 . 종단 — SCSI 케이블 양쪽 끝에 있는 마지막 장치와 같은 일부 장치는 케이블에서 반사와 불요 신호가 발생하지 않도록 종료되어야 합니다 . 이러한 장치가 직렬로 연결되어 있을 경우 , 장치의 점퍼 또는 스위치의 설정을 변경하거나 장치의 구성 소프트웨어 설정을 변경하여 이러한 장치의 종단을 활성화 또는 비활성화해야 할 수 있습니다 .
플래시 메모리 — 소프트웨어 유틸리티를 사용하여 프로그램되고 다시 프로그램 될 수 있는 전자 칩의 한 종류 . 픽셀 — 비디오 디스플레이 상의 단일 점 . 픽셀은 행과 열로 정렬되어 이미지를 만 듭니다 . 비디오 해상도는 640 x 480 과 같이 수평 방향 픽셀 수 x 수직 방향 픽셀 수 로 표시됩니다 . 핫 플러그 — 시스템의 전원이 켜져서 실행 중일 때 일반적으로 하드 드라이브 또 는 내부 냉각 팬 등의 장치를 호스트 시스템에 설치 또는 삽입하는 기능 . 호스트 어댑터 — 시스템 버스와 주변 장치 ( 일반적으로 저장 장치 ) 간의 통신 기 능을 제공하는 컨트롤러 . 확장 버스 — 시스템에는 프로세서가 NIC 와 같은 주변 장치의 컨트롤러와 통신하 도록 하는 확장 버스가 있습니다 . 확장 카드 — 시스템 보드의 확장 카드 커넥터에 꽂는 NIC 또는 SCSI 어댑터와 같 은 추가 카드 . 확장 카드는 확장 버스와 주변 장치 간에 인터페이스를 제공하여 시 스템에 특정 기능을 추가합니다 .
용어집
색인 D ㄱ Dell 문의하기 , 137 기능 및 표시등 전면 패널 , 10 Dell 에 문의하기 , 137 L LEDs 시스템 전면 , 20 ㄴ 냉각 덮개 설치 , 61 N 냉각 팬 문제 해결 , 116 분리 , 87 설치 , 89 NIC 문제 해결 , 112 냉각기 덮개 분리 , 60 P ㄷ POST 시스템 기능 액세스 , 9 드라이브 보호물 분리 , 53 설치 , 53 S SAS RAID 컨트롤러 도터 카드 문제 해결 , 120 SAS 컨트롤러 도터 카드 문제 해결 , 120 ㅁ 메모리 문제 해결 , 117 메모리 모듈 (DIMM) 구성 , 73 분리 , 76 설치 , 74 색인 149
메자닌 카드 분리 , 71 설치 , 72 메자닌 카드 설치 , 72 문제 해결 NIC, 112 SAS RAID 컨트롤러 도터 카드 , 120 냉각 팬 , 116 메모리 , 117 비디오 , 110 손상된 시스템 , 114 순서 , 109 습식 시스템 , 113 시스템 냉각 , 116 시스템 부팅 문제 , 123 외부 연결 , 110 배터리 , 114 키보드 , 110 프로세서 , 122 하드 드라이브 , 119 확장 카드 , 121 ㅂ 방열판 분리 , 61 설치 , 63 방열판 분리 , 61 방열판 설치 , 63 배전 보드 분리 , 89 배터리 150 색인 RAID 카드 배터리 문제 해결 , 120 문제 해결 , 114 배터리 ( 시스템 ) 장착 , 79 보안 , 51, 109 보증 , 31 보호물 하드 드라이브 , 53 분리 냉각 팬 , 87 메모리 모듈 (DIMMs), 76 메자닌 카드 , 71 방열판 , 61 배전 보드 , 89 시스템 보드 , 84 시스템 보드 조립품 , 58 잡속기 확장
ㅅ 설치 냉각 덮개 , 61 냉각 팬 , 89 메모리 모듈 , 74 메자닌 카드 , 72 방열판 , 63 시스템 보드 , 85 시스템 보드 조립품 , 59 전면 패널 , 106 전원 공급 장치 , 58 접속기 확장기 , 78 중앙판 , 99 프로세서 , 65 하드 드라이브 보호물 , 53 핫 스왑 하드 드라이브 , 55-56 확장 카드 , 68 확장 카드 커넥터 , 71 후면판 , 103 손상된 시스템 문제 해결 , 114 습식 시스템 문제 해결 , 113 시스템 닫기 , 87 열기 , 86 시스템 기능 액세스 , 9 시스템 냉각 문제 해결 , 116 시스템 보드 분리 , 84 설치 , 85 점퍼 설정 , 134 커넥터 , 125 시스템 보드 조립품 분리 , 58 설치 , 59 시스템 설치 AMBIOS, 36 IDE 구성 , 39 IP 주소 , 49 IPMI 구성 , 48 LAN 구성 , 48 PCI 구성 , 42 USB 구성 , 41 디폴트 게이트웨이 IP, 49 메모리 구성 , 38 부팅 설정 구성
전면 패널 설치 , 106 전원 공급 장치 분리 , 57 설치 , 58 프로세서 문제 해결 , 122 분리 , 63 설치 , 65 전화 번호 , 137 접속기 확장기 분리 , 77 설치 , 78 중앙판 분리 , 94 설치 , 99 지원 Dell 에 문의하기 , 137 ㅋ 키보드 문제 해결 , 110 ㅍ 팬 컨트롤러 보드 분리 , 92-93 표시등 전면 패널 , 10 후면 패널 , 14 ㅎ 하드 드라이브 문제 해결 , 119 분리 , 54 핫 스왑 하드 드라이브 분리 , 54 핫 스왑 하드 드라이브 설치 , 55-56 확장 카드 문제 해결 , 121 분리 , 66 설치 , 68 확장 카드 커넥터 분리 , 69 설치 , 71 후면 패널 기능 , 14 후면판 분리 , 100 설치 , 103 후면판 점퍼 설정 , 136 표시등 코드 AC 전원 , 19 NIC, 17 NIC 속도 (KVM over IP port), 17 NIC (KVM over IP port), 17 전원 및 시스템 보드 , 18 하드