Dell PowerEdge C6105 Getting Started With Your System
Dell PowerEdge C6105 Getting Started With Your System
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
______________ Information in this document is subject to change without notice. © 2014 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc. AMD® is a registered trademark and AMD Opteron™ is a trademark of Advanced Micro Devices, Inc.
CAUTION: Restricted Access Location This server is intended for installation only in restricted access locations as defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply: Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.
1 Align the end pieces of the rails on the vertical rack flanges to seat the pegs in the bottom hole of the first U and the top hole of the second U. Engage the back end of the rails until the latches lock in place. NOTE: The rails can be used in both square-hole (item 1 in the following figure) and round-hole racks (item 2 in the following figure). Figure 1. Pushing the Latch Release Buttons 2 Repeat Step 1 to position and seat the front end pieces on the vertical flanges.
Figure 2. Installing the Chassis Stabilizer Shipping Brackets 5 Tighten the thumbscrews to secure the ears of the system to the front of the rack flanges. Figure 3. Installing the Chassis onto the Rack.
Optional-Connecting the Keyboard, Mouse, and Monitor Figure 4. Optional—Connecting the Keyboard, Mouse and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws (if any) on the monitor’s cable connector.
Connecting the Power Cable(s) Figure 5. Connecting the Power Cable Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor. Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterrupted power supply or a power distribution unit.
Turning on the System Figure 6. Pressing the Power Button on the Front of the System and the Monitor Figure 7. Pressing the Power Button on the Back of the System Press the power button(s) either on the front or back of the system and on the monitor. The power indicators should light.
Complete the Operating System Setup To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system. NOTE: For the latest information on supported operating systems, see dell.com/ossupport. Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system.
NOM Information (Mexico Only) The following information is provided on the device described in this document in compliance with the requirements of the official Mexican standards (NOM): Importer Dell Inc. de México, S.A. de C.V. Paseo de la Reforma 2620-11° Piso Col. Lomas Atlas 11950 México, D.F. Model number B03S Supply voltage 100-240 V AC with 470 W/750 W/1100 W Power 200-240 V AC with 1400 W Power Frequency 50/60 Hz Current consumption 6.5-3.5 Amps with 470 W Power 8.
Technical Specifications Processor (Per System Board) Processor type One or two AMD C32 Series processors One or two AMD Opteron 4000 Series processors One or two AMD Opteron 4200 Series processors One or two AMD Opteron 4300 Series processors Expansion Bus (Per System Board) Bus type PCI Express Generation 2 Expansion slots PCIe One x16, half-length, half-height Daughter card PCIe One x8, custom slot Memory (Per System Board) Architecture 12 x DDR3 800/1066/1333/1600* MHz registered memory modu
Connectors (Per System Board) Back NIC Two RJ-45 (10/100/1000 Mbps Ethernet) Serial 9-pin, DTE, 16550-compatible USB Two 4-pin, USB 2.0-compliant Video 15-pin D-Sub VGA Management port Dedicated Ethernet port for remote management access Video (Per System Board) Video type On-board AST2050 video controller or AST1100 Video memory 8 MB Power AC power supply (per power supply) Wattage 470 W Voltage 100-240 VAC, 50-60 Hz, input current range: 6.5-3.
Maximum inrush current Initial In-rush Current cannot exceed 55 Amps (peak). Secondary In-rush Current cannot exceed 35 Amps (peak). Battery (per system board) System battery CR 2032 3.0-V lithium ion coin cell RAID battery (optional) 3.7-V lithium ion battery pack Physical Height 8.76 cm (3.45 in) Width 44.8 cm (17.6 in) Depth 75.1 cm (29.47 in) Weight (maximum configuration) 33.67 kg (74.2 lb) Weight (empty) 15.11 kg (33.
Operating One shock pulse in the positive z axis (one pulse on each side of the system) of 31 G for 2.
Printed in the U.S.A. www.dell.com | support.dell.