Dell PowerEdge C6320 소유자 매뉴얼 규정 모델: B08S 규정 유형: B08S003 July 2020 개정 A05
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2017 - 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자의 상표일 수 있습니다.
목차 장 1: Dell PowerEdge C6320 제품 개요...............................................................................................8 PowerEdge C6320 시스템이 지원하는 구성................................................................................................................... 8 시작하는 동안 시스템 기능에 액세스하기...................................................................................................................... 9 전면 패널 구조 및 표시등...............................................................................
부팅 관리자 기본 메뉴................................................................................................................................................ 58 PXE 부팅.............................................................................................................................................................................. 59 장 6: 시스템 구성 요소 설치 및 분리.................................................................................................. 60 안전 지침.......................................
프로세서 분리 .............................................................................................................................................................. 92 프로세서 설치 .............................................................................................................................................................. 93 확장 카드 조립품 및 확장 카드 .......................................................................................................................................94 확장 카드 분리........
하드 드라이브 후면판...................................................................................................................................................... 138 하드 드라이브 후면판 분리.......................................................................................................................................140 하드 드라이브 후면판 설치.......................................................................................................................................142 2.5인치 하드 드라이브 확장기 구성....................
확장 카드 문제 해결......................................................................................................................................................... 173 프로세서 문제 해결.......................................................................................................................................................... 174 장 9: 도움말 보기.......................................................................................................................... 175 Dell EMC에 문의하기......................
1 Dell PowerEdge C6320 제품 개요 Dell PowerEdge C6320은 최대 4개의 독립적 2소켓(2S) 서버를 지원할 수 있는 초집적 2U 서버입니다. 각각의 독립 서버는 최대 22 개 코어의 듀얼 Intel Xeon E5- 2600v3 또는 Intel Xeon E5- 2600v4 시리즈 프로세서, I/O 연결용 C612 칩셋, DDR4 메모리, 듀얼 포트 내 장 10기가비트 이더넷 컨트롤러(SFP+), 전용 RJ45 연결이 포함된 통합 iDRAC8 시스템 관리를 갖추고 있습니다.
그림 1 . C6320이 지원하는 구성 시작하는 동안 시스템 기능에 액세스하기 시작하는 동안 시스템 기능에 액세스하려면 다음 키를 입력합니다. 노트: SAS 또는 SATA 카드 또는 PXE 지원용 핫 키는 BIOS 부팅 모드에서만 사용할 수 있습니다. UEFI 모드에서는 부팅할 수 있는 핫 키가 없습니다. 키입력 설명 시스템 설정 프로그램을 시작합니다. BIOS Boot Manager(BIOS 부팅 관리자)를 시작합니다. PXE(Preboot eXecution Environment)/iSCSI 부팅을 시작합니다. Ctrl+C 키 LSI 2008 SAS 메자닌 카드 구성 유틸리티를 시작합니다. 자세한 내용은 SAS 어댑터 설명서를 참조하십시오. Ctrl+R 키 PERC 9 카드 구성 유틸리티를 시작합니다. 자세한 내용은 SAS RAID 카드 설명서를 참조하십시오. Ctrl+Y 키 MegaPCLI SAS RAID 관리 도구를 시작합니다.
키입력 설명 Ctrl+S 키 PXE 부팅을 위한 온보드 LAN 설정을 구성하는 유틸리티를 시작합니다. 자세한 내용은 내장형 LAN 설명서를 참조하십시오. Ctrl+I 키 온보드 SATA 컨트롤러의 구성 유틸리티를 시작합니다. Ctrl+D 키 Intel iSCSI 설정 메뉴를 시작합니다. 전면 패널 구조 및 표시등 그림 2 . 전면 패널 − 시스템 보드 4개가 장착된 3.5인치 하드 드라이브 12개(C6320 RAID 카드 및 온보드 SATA 컨트롤러) 그림 3 . 전면 패널 − 시스템 보드 4개가 장착된 2.5인치 하드 드라이브 24개(C6320 RAID 카드 및 온보드 SATA 컨트롤러) 노트: 2.5인치 하드 드라이브 확장기 구성 지원의 방향 세부사항에 대해서는 Dell.com/support에서 HDD 조닝 구성 툴을 참조하 십시오. 표 1.
표 1. 전면 패널 구조 및 표시등 (계속) 항목 표시등, 버튼 또는 커넥터 6 시스템 보드 4의 시스템 식별 표시등 또는 버튼 8 시스템 보드 3의 시스템 식별 표시등 또는 버튼 5 하드 드라이브 아이콘 설명 핫 스왑 가능 3.5인치 하드 드라이브 최대 12개. 핫 스왑 가능 2.5인치 하드 드라이브 최대 24개. * 드라이브 커버 2.5" 하드 드라이브 시스템에만 적용됩니다. 사용할 수 없 는 드라이브 슬롯입니다. 하드 디스크 드라이브 표시등 패턴 그림 4 . 3.5인치 하드 드라이브 표시등 1. 하드 드라이브 작동 표시등(녹색) 2. 하드 드라이브 상태 표시등(녹색 및 황색) 그림 5 . 2.5인치 하드 드라이브 표시등 1. 하드 드라이브 상태 표시등(녹색 및 황색) 2.
표 2.
표 3. 후면 패널 구조 및 표시등 (계속) 항목 표시등, 단추 또는 커넥터 아이콘 설명 3 USB 포트 시스템에 USB 장치를 연결할 수 있습 니다. 포트는 USB 3.0 규격입니다. 4 이더넷 커넥터 10G NIC 1 커넥터. 5 이더넷 커넥터 10G NIC 2 커넥터. 6 관리 포트 전용 관리 포트입니다. 7 USB - 직렬 포트 시스템을 호스트에 연결합니다. 8 VGA 포트 VGA 디스플레이를 시스템에 연결합니 다. 9 전원 단추/전원 및 시스템 LED 시스템 전원이 켜지면 전원 켜짐 표시 등이 녹색으로 켜집니다. 시스템에 위험 이벤트가 발생하면 전원 켜짐 표시등이 황색으로 켜집니다. 전원 단추는 시스템에 대한 DC PSU 출 력을 제어합니다. 노트: 시스템에서 사용 가능한 디스 크 공간에 따라 시스템 전원을 켤 때 비디오 모니터에 이미지가 표시 되는 데 몇 초에서 2분 이상까지 걸 릴 수 있습니다.
LAN 표시등 코드 그림 7 . QSFP 캐리어 카드의 LAN 표시등 그림 8 . LAN 표시등 1. 작동 표시등 2. 링크 및 네트워크 속도 표시등 노트: LED 점멸 속도는 트래픽 대역폭에 따라 다릅니다. 표 4. LAN 표시등 코드 구성 요소 표시등 상태 링크 및 네트워크 속도 표시등 황색으로 켜짐 1Gbps 속도로 연결 녹색으로 켜짐 10Gbps 속도로 연결 녹색으로 깜빡거림 현재 작동 중: ● OS POST 이전 ● 드라이버가 없는 OS ● 드라이버가 있는 OS 작동 표시등 패킷 밀도에 상대적인 속도로 깜빡입 니다.
그림 9 . LAN 표시등(관리 포트) 1. 속도 표시등 2. 링크 및 작동 표시등 표 5. LAN 표시등(관리 포트) 구성 요소 표시등 상태 속도 표시등 녹색으로 켜짐 1Gbps 속도로 연결 황색으로 켜짐 10/100Mbps 속도로 연결 꺼짐 액세스 없음 또는 유휴 상태 녹색으로 깜빡거림 LAN 액세스 또는 링크업 링크 및 작동 표시등 전원 및 시스템 보드 표시등 코드 시스템 전면 패널과 후면 패널의 LED는 시스템 시작 및 작동 중의 상태 코드를 표시합니다. 전면 패널의 LED 위치는 전면 패널 기능 및 표시등 섹션을 참조하십시오. 후면 패널의 LED 위치는 후면 패널 기능 및 표시등 섹션을 참조하십시오. 표 6.
1400W AC 또는 HVDC 전원 공급 장치 그림 10 . PSU 상태 표시등 1. PSU 2. AC 전원 표시등 표 7. 1400W AC/1400W HVDC PSU 표시등 구성 요소 표시등 표시등 AC 또는 DC 전원 표시등 황색으로 켜짐 오류(모든 종류의 오류) 녹색으로 켜짐 DC_OK(전원 상태 양호) 녹색으로 깜빡거림 AC_OK 표 8. 1400W AC 또는 HVDC PSU 표시등 전원 표시등 패턴 상태 녹색 전원 공급 장치에 유효한 전원이 연결되어 있으며 해당 전원 공 급 장치가 작동 중입니다. 녹색 점멸 PSU 펌웨어를 업데이트하는 경우, PSU LED가 녹색으로 깜박입 니다. 주의: PSU의 전원 코드를 뽑거나 분리하지 마십시오. 펌웨 어 업데이트가 실행 도중 중단되면 PSU가 작동하지 않게 됩 니다. Dell Lifecycle Controller를 사용해 PSU 펌웨어를 롤 백해야 합니다.
표 8. 1400W AC 또는 HVDC PSU 표시등 (계속) 전원 표시등 패턴 상태 주의: AC와 DC PSU를 결합하여 사용할 수 없으며 이러한 경우 불일치가 발생합니다. 꺼짐 전원이 연결되어 있지 않습니다. 1600W AC 또는 HVDC 전원 공급 장치 그림 11 . 전원 공급 장치(PSU) 상태 표시등 1. PSU 2. AC 전원 표시등 표 9. 1600W AC/1600W HVDC PSU 표시등 구성 요소 표시등 상태 AC 전원 표시등 황색으로 켜짐 15초간 팬 잠금 대기 모드 OTP 범위 대기 모드 +12V DC 오류 활성 모드 15초간 팬 잠금 활성 모드 녹색으로 켜짐 DC_OK(전원 상태 양호) 녹색으로 깜빡거림 대기 모드 정상 꺼짐 AC 전원이 없는 장치 베이스보드 관리 컨트롤러(BMC) 하트비트 LED 시스템 보드는 BMC 디버깅을 위한 BMC 하트 비트 LED(CR17)를 제공합니다. BMC 하트 비트 LED는 녹색입니다.
그림 12 . C6320 시스템 보드의 BMC 하트 비트 LED 1. BMC 하트 비트 LED Intel Xeon 프로세서 E5-2600 v3 및 E5-2600 v4 제품군의 시스템 구성 제한 사항 노트: 일부 시스템 하드웨어 구성은 상위 온도 제한 수준을 감소해야 할 수도 있습니다. 노트: 30°C 이상의 환경에서 또는 팬 오류가 발생한 상태에서 작동 시 시스템 성능이 저하될 수 있습니다. 표 10. Intel Xeon 프로세서 E5-2600 v3 및 E5-2600 v4 제품군의 구성 제한 사항 프로세서 3.5인치 하드 드라이브 섀시 2.
표 10. Intel Xeon 프로세서 E5-2600 v3 및 E5-2600 v4 제품군의 구성 제한 사항 (계속) 프로세서 3.5인치 하드 드라이브 섀시 2.
표 11. 외부 공기 냉각 구성 제한 (계속) 프로세서 3.5인치 하드 드라이브 섀시 2.
표 11. 외부 공기 냉각 구성 제한 (계속) 프로세서 3.5인치 하드 드라이브 섀시 2.5인치 하드 드라이브 섀시 E5-2697 v3 135W(8/6/4 코어) 및 145W(22/18/16 코어) E5-2667 v4 E5-2643 v4 E5-2637 v4 E5-2699 v4 E5-2697 v4 E5-2697A v4 시스템 서비스 태그 찾기 사용자의 시스템은 고유한 특급 서비스 코드 및 서비스 태그 번호로 식별됩니다. 특급 서비스 코드는 시스템의 전면에서 확인할 수 있 으며, 서비스 태그는 시스템의 전면에서 찾을 수 있습니다. 또는 시스템의 섀시에 있는 스티커에서 해당 정보를 확인할 수도 있습니 다. 이 정보는 Dell에서 지원 전화를 적절한 담당자에게 연결하는 데 사용됩니다. 섀시의 서비스 태그 위치는 다음과 같습니다. 그림 13 . 서비스 태그 위치 그림 14 .
그림 15 . 섀시의 서비스 태그 위치 보증 대상 하드 드라이브는 적절한 서비스 태그로 각 노드에 연결되어 있습니다. 노드에 연결된 하드 드라이브들은 아래 그림에 나와 있습니다. 그림 16 . 서비스 태그 연결 노트: 보증 대상 하드 드라이브는 노드의 해당 서비스 태그에 연결되어 있습니다.
2 설명서 리소스 이 섹션은 시스템의 설명서 리소스에 대한 정보를 제공합니다. 문서 자료 리소스 표에 나열된 문서를 보려면 다음을 수행하십시오. ● Dell EMC 지원 사이트: 1. 표의 위치 열에 있는 문서 자료 링크를 클릭합니다. 2. 필요한 제품 또는 제품 버전을 클릭합니다. 노트: 제품 이름 및 모델을 찾으려면 시스템의 전면을 참조하십시오. 3. 제품 지원 페이지에서 매뉴얼 및 문서를 클릭합니다. ● 검색 엔진 사용: ○ 검색 상자에 문서 이름 및 버전을 입력합니다. 표 12. 시스템에 대한 추가 설명서 리소스 작업 문서 위치 시스템 설정 랙에 시스템을 설치하는 방법에 대 한 정보는 랙 솔루션과 함께 제공되 는 랙 문서 자료를 참조하거나 시스 템과 함께 배송된 시작 가이드를 참 조하십시오. www.dell.
표 12. 시스템에 대한 추가 설명서 리소스 (계속) 작업 문서 위치 및 드라이버 다운로드 방법 섹션을 참조하십시오. 시스템 관리 Dell에서 제공하는 시스템 관리 소프 www.dell.com/poweredgemanuals 트웨어에 대한 자세한 내용은 Dell OpenManage 시스템 관리 개요 안내 서를 참조하십시오. OpenManage 설정, 사용, 문제 해결 에 대한 자세한 내용은 Dell OpenManage Server Administrator 사용자 가이드를 참조하십시오. www.dell.com/openmanagemanuals > OpenManage Server Administrator Dell OpenManage Essentials 설치, 사 www.dell.com/openmanagemanuals 용, 문제 해결에 대한 자세한 내용은 > OpenManage Essentials Dell OpenManage Essentials 사용자 가이드를 참조하십시오.
3 기술 사양 이 섹션에는 시스템의 기술 및 환경 사양이 설명되어 있습니다. 주제: 섀시 크기 프로세서 사양 PSU 사양 시스템 배터리 사양 메모리 사양 환경 사양 • • • • • • 섀시 크기 그림 17 . PowerEdge C6300 인클로저의 섀시 크기 표 13. Dell PowerEdge C6300 인클로저의 크기 Xa Xb Y Za(베젤 포함) Za(베젤 미포함) Zb Zc 482.3mm 448.0 mm 86.8mm N/A(해당 없음) 41.4 mm 795.9mm 762.
프로세서 사양 Dell PowerEdge C6320은 4개의 독립 서버에서 최대 2개의 Intel Xeon E5-2600 v3 또는 Intel Xeon E5-2600 v4 제품군 프로세서를 지원 합니다. PSU 사양 Dell PowerEdge C6320 시스템은 최대 2개의 AC 또는 HVDC 전원 공급 장치(PSU)를 지원합니다. Dell PowerEdge C6320은 1400W 및 1600W 전원 공급 장치의 혼합 설치를 지원하지 않습니다. 1400W 및 1600W 전원 공급 장치는 핫 스왑이 가능하며, 시스템에 전력 사 용량 조절 기능이 있는 경우에는 어떤 조건에서도 핫 스왑을 지원합니다. 표 14. PSU 사양 PSU 열 손실(최대) 주파수 전압 최대 입력 전류 최대 유입 전류(피 크) 1400W AC 5220.763 BTU/hr 50/60Hz 200-240 V AC 9A 초기 유입 전류는 55A(피크)를 초과할 수 없습니다.
환경 사양 노트: 특정 시스템 구성을 위한 환경 측정에 대한 추가 정보는 Dell.com/environmental_datasheets를 참조하십시오. 표 16. 온도 사양 온도 사양 보관 시 -40°C ~ 65°C(-40°F ~ 149°F), 시간당 최고 20°C의 온도 변화 기준 연속 작동(950m 또는 3117ft 미만의 고도에서) 장비가 직사광선을 받지 않는 상태에서 10°C ~ 35°C(50°F ~ 95°F) 신선한 공기 신선한 공기에 관한 자세한 내용은 확대된 작동 온도 섹션을 참 조하십시오. 최대 온도 그레이디언트(작동 및 보관 시) 20°C/h(36°F/h) 표 17. 확대된 작동 온도 사양 확대된 작동 온도 사양 노트: 확대된 온도 범위에서 작동하는 경우 시스템 성능에 영향을 줄 수 있습니다. 노트: 확대된 온도 범위에서 작동하는 경우 주위 온도 경고가 LCD 및 시스템 이벤트 로그에 보고될 수 있습니다.
표 19. 최대 진동 사양 최대 진동 사양 작동 시 5 ~ 350Hz에서 0.26Grms 보관 시 10Hz ~ 500Hz에서 15분 동안 1.88Grms 표 20. 최대 충격 사양 최대 충격 사양 작동 시 작동 방향으로 2.6ms 동안 (+) z축으로 31G의 충격 펄스 1회(시스 템 각 면에 1회의 펄스) 보관 시 최대 2ms 동안 (+/-) x, y, z축으로 71G의 연속 충격 펄스 6회(시 스템 각 면에 1회의 펄스) 속도 변화가 597cm/초(235인치/초)인 27G 구형파의 (+/-) x, y, z축으로 연속 충격 펄스 6회(시스템 각 면에 1회의 펄스) 표 21. 최대 고도 사양 최대 고도 사양 작동 시 -15.2m ~ 3,048m(-50ft ~ 10,000ft) 보관 시 -15.2m ~ 10,668m(-50ft ~ 35,000ft) 표 22. 공기 중 오염 물질 수준 사양 사양 공기 중 오염 물질 수준(Class) 28 기술 사양 ISA-S71.
4 초기 시스템 설정 및 구성 주제: 시스템 설정 iDRAC 구성 운영 체제 설치 옵션 • • • 시스템 설정 시스템을 설정하려면 다음 단계를 완료하십시오. 단계 1. 시스템 포장을 풉니다. 2. 랙에 시스템을 장착합니다. 랙에 시스템을 설치하는 방법에 대한 자세한 내용은 를 참조하십시오.의 Dell PowerEdge C6320 시작 안내서를 참조하십시오.Dell.com/poweredgemanuals. 3. 주변 장치를 시스템에 연결합니다. 4. 시스템을 전원 콘센트에 연결합니다. 5. 전원 단추를 누르거나 iDRAC를 사용하여 시스템을 켭니다. 6. 연결된 주변 장치를 켭니다. iDRAC 구성 iDRAC(Integrated Dell Remote Access Controller)는 시스템 관리자가 Dell EMC 시스템를 보다 생산적으로 활용하고 전반적인 가용성 을 향상시킬 수 있도록 설계되었습니다.
iDRAC에 로그인 iDRAC에 다음과 같이 로그인할 수 있습니다. ● iDRAC 사용자 ● Microsoft Active Directory 사용자 ● Lightweight Directory Access Protocol(LDAP) 사용자 기본 사용자 이름과 암호는 root 및 calvin입니다. SSO(Single Sign-On) 또는 스마트 카드를 사용하여 로그인할 수도 있습니다. 노트: iDRAC에 로그인하려면 iDRAC 자격 증명이 있어야 합니다. iDRAC 및 iDRAC 로그인 라이센스에 대한 자세한 내용은 Dell.com/idracmanuals에서 최신 Integrated Dell Remote Access Controller 사용 설명서를 참조하십시오. 운영 체제 설치 옵션 시스템에 운영 체제가 제공되어 있지 않은 경우 다음 리소스 중 하나를 사용하여 지원되는 운영 체제를 설치하십시오. 표 23.
단계 1. 다음으로 이동합니다. Dell.com/support/drivers. 2. Drivers & Downloads(드라이버 및 다운로드) 섹션 아래에서, Service Tag or Express Service Code(서비스 태그 또는 특급 서 비스 코드) 상자에 시스템 서비스 태그를 입력한 후 Submit(제출)를 클릭합니다. 노트: 서비스 태그가 없는 경우 Detect My Product(내 제품 찾기)를 선택하여 시스템이 자동으로 서비스 태그를 감지하도록 하거나 일반 지원 아래에서 제품을 검색합니다. 3. Drivers & Downloads(드라이버 및 다운로드)를 클릭합니다. 선택 항목에 해당하는 드라이버가 표시됩니다. 4. 드라이버를 USB 드라이브, CD 또는 DVD로 다운로드합니다.
5 사전 운영 체제 관리 응용프로그램 시스템 펌웨어를 사용하여 운영 체제로 부팅하지 않고 시스템의 기본 설정 및 기능을 관리할 수 있습니다. 주제: • • • • • 사전 운영 체제 응용프로그램을 관리할 수 있는 옵션 시스템 설치 프로그램 Dell Lifecycle Controller 부팅 관리자 PXE 부팅 사전 운영 체제 응용프로그램을 관리할 수 있는 옵션 이 시스템에는 다음과 같은 사전 운영 체제 응용프로그램을 관리할 수 있는 옵션이 있습니다. ● 시스템 설치 프로그램 ● 부팅 관리자 ● Dell Lifecycle Controller ● 사전 부팅 실행 환경(PXE) 관련 개념 시스템 설치 프로그램 페이지 32 관련 참조 부팅 관리자 페이지 58 Dell Lifecycle Controller 페이지 57 PXE 부팅 페이지 59 시스템 설치 프로그램 시스템 설정 화면을 사용하여 시스템의 BIOS 설정, iDRAC 설정, 및 장치 설정을 구성할 수 있습니다.
단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 키를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 관련 개념 시스템 설치 프로그램 페이지 32 관련 참조 시스템 설정 세부 정보 페이지 33 시스템 설정 세부 정보 System Setup Main Menu(시스템 설정 기본 메뉴) 화면 세부 정보는 다음과 같습니다. 옵션 설명 System BIOS BIOS 설정을 구성할 수 있습니다. iDRAC 설정 iDRAC 설정을 구성할 수 있습니다. iDRAC 설정 유틸리티는 UEFI(Unified Extensible Firmware Interface)를 사용하여 iDRAC 매개 변수를 설정하고 구성할 수 있는 인터페이스입니다. iDRAC 설정 유틸리티를 사용하여 다양한 iDRAC 매개 변수를 활성화하거 나 비활성화할 수 있습니다.
내장형 장치 페이지 46 직렬 통신 페이지 48 시스템 프로필 설정 페이지 49 기타 설정 페이지 55 관련 참조 iDRAC 설정 유틸리티 페이지 56 장치 설정 페이지 57 관련 태스크 시스템 BIOS 설정 세부 정보 페이지 34 시스템 BIOS 보기 페이지 34 시스템 BIOS 보기 System BIOS(시스템 BIOS) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다.
옵션 설명 시스템 보안 시스템 암호, 설정 암호, TPM(Trusted Platform Module) 보안 등의 시스템 보안 설정을 구성하는 옵션을 표시 합니다. 또한 시스템의 전원 및 NMI 단추를 관리합니다. 기타 설정 시스템 날짜, 시간 등을 변경하는 옵션을 표시합니다. 관련 개념 System BIOS(시스템 BIOS) 페이지 33 관련 태스크 시스템 BIOS 보기 페이지 34 시스템 정보 System Information(시스템 정보) 화면을 사용하여 서비스 태그, 시스템 모델 이름 및 BIOS 버전과 같은 시스템 속성을 볼 수 있습 니다. 관련 개념 System BIOS(시스템 BIOS) 페이지 33 관련 태스크 시스템 정보 세부 정보 페이지 35 시스템 정보 보기 페이지 35 시스템 정보 보기 System Information(시스템 정보) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다.
옵션 설명 System Model Name(시스템 모델 이름) 시스템 모델 이름을 표시합니다. System BIOS Version(시스템 BIOS 버전) 시스템에 설치된 BIOS 버전을 표시합니다. System Management Engine Version(시 스템 관리 엔진 버 전) 관리 엔진 펌웨어의 현재 버전을 표시합니다. System Service Tag(시스템 서비스 태그) 시스템 서비스 태그를 표시합니다. System Manufacturer(시 스템 제조업체) 시스템 제조업체 이름을 표시합니다. System 시스템 제조업체의 연락처 정보를 표시합니다. Manufacturer Contact Information(시스 템 제조업체 연락처 정보) System CPLD Version(시스템 CPLD 버전) 시스템 CPLD(복잡한 프로그래밍 가능 논리 장치) 펌웨어의 현재 버전을 표시합니다. UEFI Compliance 시스템 펌웨어의 UEFI 규정 준수 수준을 표시합니다.
단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 Memory Settings(메모리 설정)를 클릭합니다. 관련 개념 메모리 설정 페이지 36 관련 태스크 메모리 설정 세부 정보 페이지 37 메모리 설정 세부 정보 이 작업 정보 Memory Settings(메모리 설정) 화면 내용은 다음과 같이 설명됩니다. 옵션 설명 시스템 메모리 크기 시스템의 메모리 크기를 표시합니다. 시스템 메모리 종류 시스템에 설치된 메모리 종류를 표시합니다. 시스템 메모리 속도 메모리 속도를 표시합니다.
관련 개념 System BIOS(시스템 BIOS) 페이지 33 관련 태스크 프로세서 설정 세부 정보 페이지 38 프로세서 설정 보기 페이지 38 프로세서 설정 보기 Processor Settings(프로세서 설정) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 Processor Settings(프로세서 설정)를 클릭합니다.
옵션 설명 DCU 스트리머 프리 DCU(Data Cache Unit) 스트리머 프리페처를 활성화하거나 비활성화할 수 있습니다. 기본적으로 이 옵션은 활 페처 성화로 설정됩니다. DCU IP 프리페처 DCU(Data Cache Unit) IP 프리페처를 활성화하거나 비활성화합니다. 기본적으로 이 옵션은 활성화로 설정됩 니다. 논리 프로세서 유휴 시스템의 에너지 효율성을 향상시킬 수 있습니다. 이 옵션은 운영 체제 코어 파킹 알고리듬을 사용하여 일부 상태 논리 프로세서를 시스템에 파킹하여 해당 프로세서 코어가 전원 유휴가 낮은 상태로 전환되도록 합니다. 이 옵션은 운영 체제에서 지원되는 경우에만 활성화되며 기본적으로 Disabled(비활성화)로 설정됩니다. TDP 구성 POST 중에 시스템의 전원 및 열 전달 기능을 기반으로 프로세서 TDP(Thermal Design Power) 레벨을 재구성할 수 있습니다. TDP는 냉각 시스템이 발산되는 데 필요한 최대 열을 확인합니다.
SATA 설정 보기 페이지 40 SATA 설정 보기 SATA Settings(SATA 설정) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 SATA Settings(SATA 설정)를 클릭합니다. 관련 개념 SATA 설정 페이지 39 관련 태스크 SATA 설정 세부 정보 페이지 40 SATA 설정 세부 정보 이 작업 정보 SATA Settings(SATA 설정) 화면 내용은 다음과 같이 설명됩니다.
옵션 Port C(포트 C) 설명 옵션 설명 모델 선택한 장치의 드라이브 모델을 표시합니다. 드라이브 유형 SATA 포트에 연결된 드라이브의 종류를 표시합니다. 용량 하드 드라이브의 전체 용량을 표시합니다. 옵티컬 드라이브와 같은 이동식 미디어 장 치에 대해서는 이 필드가 정의되지 않습니다. 선택한 장치에 대한 드라이브 종류를 설정합니다. ATA 모드의 Embedded SATA settings(내장형 SATA 설 정)에서 BIOS 지원을 활성화하려면 이 필드를 Auto(자동)로 설정합니다. BIOS 지원을 끄려면 OFF(끄기)로 설정합니다. AHCI 또는 RAID 모드에 대한 BIOS 지원을 항상 사용할 수 있습니다. Port D(포트 D) 옵션 설명 모델 선택한 장치의 드라이브 모델을 표시합니다. 드라이브 유형 SATA 포트에 연결된 드라이브의 종류를 표시합니다. 용량 하드 드라이브의 전체 용량을 표시합니다.
관련 개념 SATA 설정 페이지 39 관련 태스크 SATA 설정 보기 페이지 40 부팅 설정 Boot Settings(부팅 설정) 화면을 사용하여 부팅 모드를 BIOS 또는 UEFI로 설정할 수 있습니다. 또한 부팅 순서를 지정할 수도 있습 니다. 관련 개념 System BIOS(시스템 BIOS) 페이지 33 관련 참조 시스템 부팅 모드 선택 페이지 43 관련 태스크 부팅 설정 세부 정보 페이지 42 부팅 설정 보기 페이지 42 부팅 순서 변경 페이지 44 부팅 설정 보기 Boot Settings(부팅 설정) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3.
옵션 설명 Boot Mode(부팅 모 시스템의 부팅 모드를 설정할 수 있습니다. 드) 주의: 운영 체제가 설치된 부팅 모드가 아닌 다른 부팅 모드로 전환하면 시스템가 부팅되지 않을 수 있습 니다. 운영 체제에서 UEFI를 지원하는 경우 이 옵션을 UEFI로 설정할 수 있습니다. 이 필드를 BIOS로 설정하면 UEFI 를 지원하지 않는 운영 체제와의 호환성을 유지할 수 있습니다. 기본적으로 이 옵션은 BIOS로 설정됩니다. 노트: 이 필드를 UEFI로 설정하는 경우 BIOS Boot Settings(UEFI 부팅 설정) 메뉴가 비활성화됩니다. 이 필드를 BIOS로 설정하는 경우 UEFI Boot Settings(UEFI 부팅 설정) 메뉴가 비활성화됩니다. Boot Sequence Boot Sequence Retry(부팅 순서 재시도) 기능을 활성화하거나 비활성화합니다.
관련 개념 부팅 설정 페이지 42 관련 태스크 부팅 설정 세부 정보 페이지 42 부팅 설정 보기 페이지 42 부팅 순서 변경 이 작업 정보 USB 키 또는 광학 드라이브에서 부팅하려는 경우 부팅 순서를 변경해야 할 수도 있습니다. 아래의 지침은 Boot Mode(부팅 모드)에 대해 BIOS를 선택한 경우 다를 수 있습니다. 단계 1. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS) > Boot Settings(부팅 설정)을 클릭 합니다. 2. Boot Option Settings(부팅 옵션 설정) > Boot Sequence(부팅 순서)를 클릭합니다. 3. 화살표 키를 사용하여 부팅 장치를 선택하고 + 및 - 키를 사용하여 순서대로 장치를 아래 또는 위로 이동합니다. 4. Exit(종료)를 클릭하고 Yes(예)를 클릭하여 설정을 저장합니다.
단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 Network Settings(네트워크 설정)를 클릭합니다. 관련 개념 네트워크 설정 페이지 44 관련 태스크 네트워크 설정 화면 세부 정보 페이지 45 네트워크 설정 화면 세부 정보 Network Settings(네트워크 설정) 화면의 세부 정보는 다음과 같이 설명됩니다. 이 작업 정보 옵션 설명 PXE Device n(PXE 장치를 활성화 또는 비활성화합니다. 활성화된 경우 UEFI 부팅 옵션이 장치에 대해 생성됩니다.
UEFI iSCSI 설정 보기 UEFI iSCSI Settings(UEFI iSCSI 설정) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 Network Settings(네트워크 설정)를 클릭합니다. 5. Network Settings(네트워크 설정) 화면에서 UEFI iSCSI Settings(UEFI iSCSI 설정)를 클릭합니다.
4. System BIOS(시스템 BIOS) 화면에서 Integrated Devices(내장형 장치)를 클릭합니다. 관련 개념 내장형 장치 페이지 46 관련 태스크 내장형 장치 세부 정보 페이지 47 내장형 장치 세부 정보 이 작업 정보 Integrated Devices(내장형 장치) 화면 세부 정보는 다음과 같습니다. 옵션 설명 USB 3.0 Setting(USB 3.0 설정) USB 3.0 지원을 활성화 또는 비활성화합니다. 이 옵션은 운영 체제가 USB 3.0을 지원하는 경우에만 사용할 수 있습니다. 이 옵션을 비활성화하면 장치가 USB 2.0 속도로 작동합니다. USB 3.0은 기본적으로 활성화됩니다. User Accessible USB Port(사용자 접근 가능한 USB 포트) USB 포트를 활성화 또는 비활성화할 수 있습니다.
옵션 설명 Memory Mapped I/O above 4 GB(4GB 이상의 메 모리 매핑 /O) 대용량 메모리가 필요한 PCIe 장치 지원을 활성화하거나 비활성화합니다. 기본적으로 이 옵션은 Enabled(활 성화)로 설정됩니다. Slot Disablement(슬롯 비활성화) 시스템에서 사용 가능한 PCIe 슬롯을 활성화하거나 비활성화합니다. 슬롯 비활성화 기능은 지정된 슬롯에 설 치된 PCIe 카드의 구성을 제어합니다. 슬롯 비활성화는 설치된 주변 장치 카드로 인해 운영 체제에 부팅할 수 없거나 시스템 시작이 지연되는 경우에만 사용해야 합니다. 슬롯이 비활성화되면 옵션 ROM과 UEFI 드라이버 가 모두 비활성화됩니다. 관련 개념 내장형 장치 페이지 46 관련 태스크 내장형 장치 보기 페이지 46 직렬 통신 Serial Communication(직렬 통신) 화면을 사용하면 직렬 통신 포트 속성을 볼 수 있습니다.
직렬 통신 세부 정보 이 작업 정보 직렬 통신 화면 세부 정보는 다음과 같습니다. 옵션 설명 직렬 통신 BIOS에서 직렬 통신 장치(직렬 장치 1 및 직렬 장치 2)를 선택합니다. BIOS 콘솔 리디렉션을 활성화하고 포트 주소를 지정할 수도 있습니다. 이 옵션은 기본값으로 Auto(자동)로 설정됩니다. 직렬 포트 주소 직렬 장치의 포트 주소를 설정할 수 있습니다. 이 옵션은 기본적으로 Serial Device 1=COM2, Serial Device 2=COM1(직렬 장치 1=COM2, 직렬 장치 2=COM1)로 설정되어 있습니다. 노트: Serial Over LAN(SOL) 기능으로는 직렬 장치 2만 사용할 수 있습니다. SOL을 통한 콘솔 재지정을 사 용하려면 콘솔 재지정 및 직렬 디바이스에 대해 동일한 포트 주소를 구성합니다. 노트: 시스템를 부팅할 때마다 BIOS가 iDRAC의 직렬 MUX 설정을 동기화합니다. 직렬 MUX 설정은 iDRAC에서 독립적으로 변경할 수 있습니다.
단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 키를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 System Profile Settings(시스템 프로필 설정)를 클릭합니다. 관련 개념 시스템 프로필 설정 페이지 49 관련 태스크 시스템 프로필 설정 세부 정보 페이지 50 시스템 프로필 설정 세부 정보 이 작업 정보 System Profile Settings(시스템 프로필 설정) 화면 내용은 다음과 같이 설명됩니다. 옵션 설명 System Profile(시 스템 프로필) 시스템 암호를 설정할 수 있습니다.
옵션 설명 Memory Refresh Rate(메모리 새로 고침) 1x 또는 2x 중 하나로 메모리 갱신율을 설정합니다. 기본적으로 이 옵션은 Nominal(공칭)로 설정됩니다. Uncore Frequency(언코어 빈도) Processor Uncore Frequency(프로세서 언코어 빈도) 옵션을 선택할 수 있습니다. Dynamic mode(동적 모드)를 사용하면 프로세서가 진행 시간 동안 코어 및 언코어 전반의 전원 리소스를 최적 화할 수 있습니다. 전력을 절약하거나 성능을 최적화하기 위해 언코어 빈도를 최적화하는 것은 Energy Efficiency Policy(에너지 효율 정책) 옵션의 설정에 따라 영향을 받습니다. Energy Efficient Energy Efficient Policy(에너지 효율 정책) 옵션을 선택할 수 있습니다. Policy(에너지 효율 CPU가 프로세서의 내부 동작을 조작하는 설정을 사용하며 높은 성능 또는 전력 절감을 목표로 하는지 여부를 정책) 결정합니다.
시스템 및 설정 암호를 삭제 또는 변경 페이지 54 시스템 보안 보기 System Security(시스템 보안) 화면을 보려면 다음 단계를 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음 메시지가 표시되면 즉시 F2를 누릅니다. F2 = System Setup 노트: F2를 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료한 다음 시스템를 재시작하고 다시 시도합니 다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS)를 클릭합니다. 4. System BIOS(시스템 BIOS) 화면에서 System Security(시스템 보안)를 클릭합니다. 관련 개념 시스템 보안 페이지 51 관련 태스크 시스템 보안 설정 세부 정보 페이지 52 시스템 보안 설정 세부 정보 이 작업 정보 System Security Settings(시스템 보안 설정) 화면 내용은 다음과 같이 설명됩니다.
옵션 설명 NMI 버튼 시스템 전면에 있는 NMI 버튼을 활성화하거나 비활성화합니다. 기본적으로 이 옵션은 비활성화로 설정됩니 다. AC Power Recovery 시스템의 AC 전원이 복구된 후 시스템가 어떻게 반응할지 설정합니다. 기본적으로 이 옵션은 Last(마지막)로 설정됩니다. AC Power Recovery Delay AC 전원이 시스템에 복구된 후 시스템 전원을 켤 때 지연되는 시간을 설정합니다. 이 옵션은 기본적으로 Immediate(즉시)로 설정됩니다. User Defined Delay(사용자 정의 지연)(60초 ~ 240 초) AC Power Recovery Delay(AC 전원 복구 지연)에 대한 User Defined(사용자 정의) 옵션이 선택되어 있는 경 우 User Defined Delay(사용자 정의 지연) 옵션을 설정합니다. UEFI Variable Access 다양한 수준의 고정 UEFI 변수를 제공합니다.
노트: 암호 보호 기능은 시스템를 재부팅해야만 적용됩니다. 관련 개념 시스템 보안 페이지 51 시스템 암호를 사용하여 시스템 보호 이 작업 정보 설정 암호를 지정하면 시스템 암호 대신 설정 암호를시스템사용할 수 있습니다. 단계 1. 시스템를 켜거나 재부팅합니다. 2. 시스템 암호를 입력하고 Enter를 누릅니다. 다음 단계 Password Status(암호 상태)를 Locked(잠금)로 설정한 경우, 재부팅 시 메시지가 나타나면 시스템 암호를 입력하고 Enter를 누릅니 다. 노트: 잘못된 시스템 암호를 입력하면 시스템가 메시지를 표시하며 암호를 다시 입력하라고 묻습니다. 올바른 암호 입력을 세 번 까지 시도할 수 있습니다. 세 번째 시도가 실패하면 시스템에서 시스템가 작동을 멈췄으며 꺼야 한다는 오류 메시지를 표시합니 다. 시스템를 종료하고 다시 시작해도 올바른 암호를 입력할 때까지 오류 메시지가 계속 표시됩니다.
활성화된 설정 암호를 사용하여 시스템 작동 Setup Password(설정 암호)를 Enabled(활성화)로 설정한 경우 시스템 설정 프로그램의 옵션을 수정하기 전에 정확한 설정 암호를 입력합니다. 세 번 이상 잘못된 암호를 입력하면 시스템에 다음과 같은 메시지가 나타납니다. Password Invalid. Number of unsuccessful password attempts: Maximum number of password attempts exceeded.System halted. 시스템를 종료하고 다시 시작해도 올바른 암호를 입력할 때까지 오류 메시지가 계속 표시됩니다. 다음과 같이 옵션이 설정된 경우는 예외입니다. ● System Password(시스템 암호) 설정이 Enabled(활성화)가 아니고 시스템 암호가 Password Status(암호 상태) 옵션을 통해 잠기지 않은 경우에는 시스템 암호를 지정할 수 있습니다. 자세한 내용은 시스템 보안 설정 화면 섹션을 참조하십시오.
기타 설정 세부 정보 이 작업 정보 Miscellaneous Settings(기타 설정) 화면에 다음과 같은 내용이 표시됩니다. 옵션 설명 System Time(시스 시스템의 시간을 설정합니다. 템 시간) System Date(시스 템 날짜) 시스템의 날짜를 설정합니다. Asset Tag(자산 태 그) 자산 태그를 표시하며, 보안 및 추적 용도로 자산 태그를 수정할 수 있습니다. Keyboard NumLock(키보드 NumLock) 시스템가 부팅할 때 NumLock이 활성화될지 또는 비활성화될지 설정합니다. 기본적으로 이 옵션은 Nominal(공칭)로 설정됩니다. F1/F2 Prompt on Error(오류 시 F1/F2 프롬프트) 오류 시 F1/F2 프롬프트를 활성화하거나 비활성화합니다. 기본적으로 이 옵션은 Enabled(활성화)로 설정됩 니다. F1/F2 프롬프트는 키보드 오류 또한 포함합니다.
iDRAC 설정 유틸리티 시작 단계 1. 관리되는 시스템를 켜거나 재시작합니다. 2. POST(Power-On Self-Test) 중에 F2 키를 누릅니다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 페이지에서 iDRAC Settings(iDRAC 설정)를 클릭합니다. iDRAC Settings(iDRAC 설정) 화면이 표시됩니다. 관련 참조 iDRAC 설정 유틸리티 페이지 56 열 설정 변경 iDRAC 설정 유틸리티는 시스템의 열 제어 설정을 선택하여 사용자 지정할 수 있도록 해줍니다. 1. iDRAC Settings(iDRAC 설정) > Thermal(열)을 클릭합니다. 2. SYSTEM THERMAL PROFILE(시스템 열 프로필) > Thermal Profile(열 프로필)에서 다음 옵션 중 하나를 선택합니다. ● 기본 열 프로필 설정 ● 최대 성능(성능 최적화) ● 최소 전력(와트당 성능 최적화) 3.
관련 참조 Dell Lifecycle Controller 페이지 57 부팅 관리자 Boot Manager(부팅 관리자) 화면에서 부팅 옵션과 진단 유틸리티를 선택할 수 있습니다. 관련 개념 부팅 관리자 기본 메뉴 페이지 58 System BIOS(시스템 BIOS) 페이지 33 관련 태스크 부팅 관리자 보기 페이지 58 부팅 관리자 보기 부팅 관리자를 시작하려면 다음을 수행하십시오. 단계 1. 시스템를 켜거나 재시작합니다. 2. 다음과 같은 메시지가 나타나면 F11을 누릅니다. F11 = Boot Manager F11을 누르기 전에 운영 체제가 로드되기 시작하면 시스템가 부팅을 완료하게 한 다음 시스템를 재시작하고 다시 시도합니다. 관련 개념 부팅 관리자 기본 메뉴 페이지 58 관련 참조 부팅 관리자 페이지 58 부팅 관리자 기본 메뉴 메뉴 항목 설명 일반 부팅 계속 시스템는 먼저 부팅 순서의 첫 번째 항목에 해당하는 장치로 부팅을 시도합니다.
일회용 BIOS 부팅 메뉴 일회용 BIOS 부팅 메뉴를 사용하면 부팅할 부팅 장치를 선택할 수 있습니다. 관련 참조 부팅 관리자 페이지 58 시스템 유틸리티 System Utilities(시스템 유틸리티)에는 실행할 수 있는 다음과 같은 유틸리티가 포함되어 있습니다. ● 진단 프로그램 시작 ● BIOS/UEFI 업데이트 파일 탐색기 ● 시스템 재부팅 노트: 선택한 부팅 모드에 따라 BIOS 또는 UEFI 업데이트 파일 탐색기가 있을 것입니다. 관련 참조 부팅 관리자 페이지 58 PXE 부팅 PXE(preboot eXecution Environment) 옵션을 사용하여 네트워크에 연결된 시스템를 원격으로 부팅하고 구성할 수 있습니다. 노트: PXE 부팅 옵션에 액세스하려면, 시스템를 부팅한 다음 F12를 누릅니다. 시스템 검사하고 네트워크로 연결된 활성 시스템 를 표시합니다.
6 시스템 구성 요소 설치 및 분리 주제: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 안전 지침 시스템 내부 작업을 시작하기 전에 시스템 내부 작업을 마친 후에 권장 도구 시스템 덮개 시스템 내부 냉각 팬 하드 드라이브 SSD 및 SSD 홀더 SATADOM 전원 공급 장치 시스템 보드 트레이 시스템 보드 조립품 냉각 덮개 방열판 프로세서 확장 카드 조립품 및 확장 카드 PCI-E 슬롯 우선 순위 PERC 카드 라이저 카드 선택 사양 메자닌 카드 메자닌 카드 브리지 보드 시스템 메모리 시스템 배터리 시스템 보드 TPM(Trusted Platform Module) 배전 보드 중앙판 하드 드라이브 후면판 2.5인치 하드 드라이브 확장기 구성 제어판 센서 보드 안전 지침 노트: 시스템을 들어 올려야 할 경우에는 다른 사람의 도움을 받으십시오. 부상을 방지하려면 혼자 시스템을 들어 올리지 마십시 오.
노트: 적절한 작동 및 냉각을 유지하려면 시스템 팬 및 시스템의 모든 베이에 구성 요소 또는 보호물이 항상 장착되어 있어야 합 니다. 부상이나 시스템 손상을 방지하려면 다음 지침을 따르십시오. ● 시스템 내부 작업을 할 때마다 항상 시스템을 전원 콘센트에서 분리합니다. ● 가능하면 시스템 내부 작업 시 손목 접지대를 착용합니다. 또는 시스템 케이스의 베어 메탈 섀시나 접지된 다른 어플라이언스의 베어 메탈 본체를 만져서 정전기를 방전합니다. ● 전자 회로 기판은 가장자리로만 잡으십시오. 필요한 경우가 아니면 보드의 구성요소를 만지지 마십시오. 회로 기판을 구부리거나 압력을 가하지 마십시오. ● 설치에 사용할 준비가 될 때까지 모든 구성 요소를 정전기 방지 포장에 넣어 보관합니다. 시스템 내부 작업을 시작하기 전에 전제조건 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 연결된 주변장치와 시스템를 끄십시오. 2. 전원 콘센트에서 시스템를 분리하고 주변 장치도 분리합니다. 3.
● 집게 ● 손목 접지대 시스템 덮개 시스템 덮개를 시스템 내부의 구성 요소를 보호하고 시스템 내부의 공기 흐름을 유지 관리합니다. 시스템 덮개 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 연결된 모든 주변 장치를 포함하여 시스템의 각 슬레드 전원을 끕니다. 전원 콘센트에서 시스템을 분리하고 주변 장치도 분리합니다. 십자 드라이버(# 2)를 준비합니다. 단계 1. 시스템 덮개에서 고정 나사를 분리합니다. 2. 덮개 분리 래치 잠금 장치를 누릅니다. 3.
관련 태스크 시스템 덮개 장착 페이지 63 시스템 덮개 장착 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 십자 드라이버(# 2)를 준비합니다. 단계 1. 시스템 덮개를 섀시 위에 놓고 제자리에 고정될 때까지 섀시 전면으로 밉니다. 2. 시스템 덮개를 나사로 제자리에 고정합니다. 다음 단계 1. 시스템을 전원 콘센트에 다시 연결합니다. 2. 연결된 모든 주변 장치를 포함하여 시스템의 각 슬레드 전원을 켭니다. 관련 참조 안전 지침 페이지 60 시스템 내부 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
7. 하드 드라이브 베이 9. 라이저 카드 브래킷 8. 하드 드라이브(12개) 냉각 팬 서버는 작동을 위해 많은 전력을 사용하며 이로 인해 많은 열이 발생됩니다. 냉각 시스템을 배치해 이 열을 제거하지 않으면 이 열로 인해 서버의 전자 및 기계 부품이 파괴될 수 있습니다. 대부분의 경우, 이 열을 제거하는 가장 단순하고 효율적인 방법은 팬을 사용하 는 것입니다. 냉각 팬 분리 전제조건 경고: 냉각 팬이 없을 때 시스템을 작동하지 마십시오. 경고: 냉각 팬은 시스템 전원이 꺼진 후에 얼마간 계속 돌아갈 수 있습니다. 운영 체제에서 팬을 제거하기 전에 팬이 멈출 때까지 잠시 기다리십시오. 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다.
그림 21 . 냉각 팬 분리 및 설치 1. 3. 5. 7. 냉각 팬 케이지 냉각 팬 2 냉각 팬 3 팬 케이블 2. 냉각 팬 1 4. 스폰지 6. 냉각 팬 4 다음 단계 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 덮개 분리 페이지 62 시스템 내부 작업을 시작하기 전에 페이지 61 냉각 팬 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 단계 1. 냉각 팬을 스폰지에 맞추고 냉각 팬이 단단히 장착될 때까지 냉각 팬 케이지로 밉니다.
그림 22 . 냉각 팬 설치 3. 냉각 팬 케이지를 섀시의 고정 핀에 맞추고 제자리에 단단히 장착될 때까지 섀시로 밉니다. 4. 팬의 전원 케이블을 배전 보드 1의 커넥터에 연결합니다. 케이블이 조이거나 구겨지지 않도록 타이를 통해 적절히 배선합니다. 다음 단계 1. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 2. 팬이 최적의 속도로 회전하는지를 확인하기 위해 관리 소프트웨어를 확인합니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 내부 작업을 마친 후에 페이지 61 하드 드라이브 하드 드라이브는 디지털 정보를 저장하고 검색하는 데 사용되는 데이터 스토리지 디바이스입니다. 주의: SAS/SATA 백플레인에서 사용할 수 있도록 검사 및 승인된 하드 드라이브만 사용하십시오. 다음은 SAS 하드 드라이브, SATA 하드 드라이브 및 SSD의 혼합 설치 시 지침입니다. ● 각 슬레드는 6개의 2.5인치 하드 드라이브 또는 솔리드 스테이트 드라이브를 지원합니다.
노트: 이 항목은 핫 스왑 가능 하드 드라이브가 있는 시스템에만 적용됩니다. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 하드 드라이브 보호물을 하드 드라이브 베이에서 당겨 꺼냅니다. 그림 23 . 3.5인치 하드 드라이브 보호물 분리 및 설치 a. 3.5인치 하드 드라이브 보호물 관련 참조 안전 지침 페이지 60 3.5인치 하드 드라이브 보호물 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 하드 드라이브 보호물이 제자리에 장착될 때까지 드라이브 베이에 밀어 넣습니다. 관련 참조 안전 지침 페이지 60 2.
주의: 적절한 시스템 냉각 상태를 유지하려면 모든 빈 하드 드라이브 베이에 하드 드라이브 보호물이 설치되어 있어야 합니다. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 2.5인치 하드 드라이브 보호물의 핸들을 당겨 2.5인치 하드 드라이브 보호물을 하드 드라이브 베이에서 빼냅니다. 그림 24 . 2.5인치 하드 드라이브 보호물 분리 및 설치 a. 2.5인치 하드 드라이브 보호물 b. 핸들 c. 래치 다음 단계 2.5인치 하드 드라이브 보호물을 설치합니다. 관련 참조 안전 지침 페이지 60 2.5인치 하드 드라이브 보호물 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
하드 드라이브 캐리어 분리 3.5인치 하드 드라이브와 2.5인치 하드 드라이브의 설치 및 분리 절차는 비슷합니다. 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 적절한 시스템 냉각 상태를 유지하려면 모든 빈 하드 드라이브 베이에 하드 드라이브 보호물이 설치되어 있어야 합니다. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 잠금 레버가 잠금 해제 기호를 가리킬 때까지 시계 반대 방향으로 돌립니다. 2. 분리 단추를 밀어 분리 핸들을 엽니다. 3. 분리 핸들을 사용하여 하드 드라이브 캐리어를 하드 드라이브 베이에서 당겨 꺼냅니다. 그림 25 .
주의: 적절한 시스템 냉각 상태를 유지하려면 모든 빈 하드 드라이브 캐리어 베이에 하드 드라이브 캐리어 보호물이 설치되어 있 어야 합니다. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 하드 드라이브 캐리어의 해제 레버를 열고 하드 드라이브 커넥터가 후면판에 맞물릴 때까지 하드 드라이브 캐리어를 드라이브 베 이로 밀어 넣습니다. 2. 분리 핸들을 눌러 하드 드라이브 캐리어를 제자리에 고정합니다. 3. 레버 잠금 장치가 잠금 표시를 가리키도록 시계 방향으로 돌립니다. 그림 26 . 하드 드라이브 캐리어 설치 다음 단계 1. 하드 드라이브의 상태를 확인하려면 하드 드라이브 작동 및 상태 표시등을 확인합니다. 2. 설치된 하드 드라이브의 상태를 확인하려면 관리 소프트웨어를 확인하십시오. 관련 참조 안전 지침 페이지 60 하드 디스크 드라이브 표시등 패턴 페이지 11 하드 드라이브 캐리어에서 하드 드라이브 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
3. 십자 드라이버(# 2)를 준비합니다. 단계 1. 섀시에 하드 드라이브를 고정시키고 있는 나사를 분리합니다. 2. 하드 드라이브 캐리어에서 하드 드라이브를 들어냅니다. 그림 27 . 하드 드라이브 캐리어에서 하드 드라이브 분리 및 설치 a. b. 나사(4개) c. 하드 드라이브 캐리어 다음 단계 1. 하드 드라이브 캐리어에 하드 드라이브를 삽입합니다. 2. 하드 드라이브 베이에 하드 드라이브 캐리어를 설치합니다. 관련 참조 안전 지침 페이지 60 하드 드라이브 캐리어에 하드 드라이브 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1.
그림 28 . 하드 드라이브 캐리어에 하드 드라이브 설치 노트: 레이블이 위를 향하도록 하드 드라이브를 설치해야 합니다. 즉, 하드 드라이브 커넥터가 후면판의 커넥터와 정렬되는 지 확인해야 합니다. 다음 단계 1. 하드 드라이브 베이에 하드 드라이브 캐리어를 설치합니다. 2. 하드 드라이브의 상태를 확인하려면 하드 드라이브 작동 및 상태 표시등을 확인합니다. 3. 설치된 하드 드라이브의 상태를 확인하려면 관리 소프트웨어를 확인하십시오. 관련 참조 안전 지침 페이지 60 3.5인치 하드 드라이브 캐리어에 2.5인치 SSD 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 29 . 2.5인치 SSD 설치 및 2.5인치 어댑터 브래킷에서 분리하기 a. 2.5인치 SSD b. M3 나사(2개) c. 2.5인치 어댑터 3. 어댑터 조립품을 3.5인치 하드 드라이브 캐리어에 넣습니다. 4. 어댑터 조립품을 3.5인치 하드 드라이브 캐리어에 나사로 고정합니다. 그림 30 . 어댑터 조립품 설치 및 하드 드라이브 캐리어에서 분리하기 a. 어댑터 조립품 b. 나사(3개) c. 하드 드라이브 캐리어 노트: 광 파이프가 있는 SSD 측면의 나사 구멍에는 나사를 설치하지 마십시오.
그림 31 . 광 파이프가 있는 SSD 측면의 나사 구멍 관련 참조 안전 지침 페이지 60 SSD 및 SSD 홀더 솔리드 스테이트 드라이브(SSD, 실제 디스크나 디스크를 회전시키는 모터가 포함되어 있지 않지만 솔리드 스테이트 디스크라고도 합니다)는 집적 회로 조립품을 메모리로 사용하여 데이터를 지속적으로 저장하는 반도체 저장 장치입니다. SSD에는 가동(기계적) 구 성 요소가 없습니다. SSD는 일반적으로 물리적 충격에 대한 내성이 더 뛰어나며, 액세스 시간과 지연 시간이 더 짧습니다. SSD 및 SSD 홀더 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4.
그림 32 . MicroSATA 케이블이 장착된 SSD 분리 a. 시스템 보드 조립품 b. MicroSATA 케이블이 장착된 SSD c. SSD 홀더 3. SSD에서 MicroSATA 케이블을 분리합니다 . 그림 33 . MicroSATA 케이블 분리 a. SSD b. MicroSATA 케이블 4. SSD 홀더를 배터리 백업 장치(BBU) 브래킷에 고정하는 나사를 분리합니다. 5. BBU 브래킷에서 SSD 홀더를 분리합니다.
그림 34 . SSD 홀더 분리 1. 시스템 보드 조립품 3. SSD 홀더 2. 나사 4. BBU 브래킷 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 SSD 및 SSD 홀더 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. SSD 홀더를 배터리 백업 장치(BBU) 브래킷에 놓습니다. 2. SSD 홀더를 BBU 브래킷에 고정시키는 나사를 장착합니다. 3. MicroSATA 케이블을 SSD에 연결합니다. 4. MicroSATA 케이블이 장착된 SSD를 SSD 홀더 안으로 밉니다. 5.
DC - DC 보드 DC-DC 보드는 1.8인치 SSD에 전원을 공급하는 전원 조절 보드입니다. DC - DC 보드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 연결된 주변장치와 시스템을 끄십시오. 전원 콘센트에서 시스템을 분리하고 주변 장치도 분리합니다. 시스템 보드 조립품을 분리합니다. 단계 1. 모든 케이블을 분리합니다. 2. 집게를 사용하여 공간 서포트를 누르고 DC - DC 보드의 한쪽을 들어 올립니다. 3. 다른 공간 서포트에 대해서 2단계를 반복하고 DC - DC 보드의 다른 쪽을 들어 올립니다.
그림 36 . DC - DC 보드 설치 a. BBU 브래킷 b. 공간 서포트(2개) c. DC - DC 보드 2. 모든 케이블을 다시 연결합니다. 다음 단계 1. 시스템 보드를 설치합니다. 2. 주변 장치를 다시 장착하고 시스템을 전원 콘센트에 연결합니다. 3. 연결된 주변장치와 시스템을 켜십시오. SSD 및 DC - DC 보드와 LSI 2008의 케이블 라우팅 이 작업 정보 표 25. SSD 및 DC - DC 보드와 LSI 2008의 케이블 라우팅 항목 케이블 시작(LSI 2008 SAS 메자닌 카드) 종료(시스템 보드) 1 미니 SAS 케이블 미니 SAS 커넥터 4 ~ 7(J4) SAS/SATA 커넥터 4, 5 LSI 2008 SAS 메자닌 카드 2 미니 SAS 커넥터 0 ~ 3(J3) 미니 SAS HD 커넥터 0 ~ 3 LSI 2008 SAS 메자닌 카드 3 MicroSATA 케이블 1.8인치 SSD 4 1.
그림 37 . SSD 및 DC - DC 보드와 LSI 2008의 케이블 라우팅 표 26. SSD 및 DC - DC 보드와 LSI 2008의 케이블 라우팅 항목 케이블 시작(LSI 2008 SAS 메자닌 카드) 종료(시스템 보드) 미니 SAS 케이블 미니 SAS 커넥터 4 ~ 7(J4) SAS/SATA 커넥터 4, 5 LSI 2008 SAS 메자닌 카드 미니 SAS 커넥터 0 ~ 3(J3) 미니 SAS HD 커넥터 0 ~ 3 LSI 2008 SAS 메자닌 카드 MicroSATA 케이블 1.8인치 SSD 1x4 전원 케이블 시스템 보드의 온보드 SATA 커넥터 5 1.8인치 SSD DC - DC 보드(J2) DC - DC - DC 보드(J1) 시스템 보드의 하이 파워 커넥터 SATADOM SATADOM 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
그림 38 . SATADOM 분리 a. 시스템 보드 조립품 b. SATADOM c. 금속 래치 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 SATADOM 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. SATADOM의 가장자리를 잡고 카드 에지 커넥터가 시스템 보드의 SATA 커넥터 5에 맞춰지도록 배치합니다. 2. 완전히 장착될 때까지 SATADOM을 엄지 손가락으로 누릅니다. 3. 모든 케이블을 다시 연결합니다. 다음 단계 1. 주변 장치를 다시 장착하고 시스템을 전원 콘센트에 연결합니다. 2.
SATADOM 및 LSI 2008을 위한 케이블 라우팅 그림 39 . SATADOM 및 LSI 2008을 위한 케이블 라우팅 표 27. SATADOM 및 LSI 2008을 위한 케이블 라우팅 항목 케이블 시작(LSI 2008 SAS 메자닌 카드) 종료(시스템 보드) 미니 SAS 케이블 미니 SAS 커넥터 4 ~ 7(J4) SAS/SATA 커넥터 4, 5 LSI 2008 SAS 메자닌 카드 미니 SAS 커넥터 0 ~ 3(J3) 미니 SAS HD 커넥터 0 ~ 3 LSI 2008 SAS 메자닌 카드 SATADOM 전원 케 이블 시스템 보드의 HDD 전원 커넥터 SATADOM 전원 공급 장치 노트: 이 표에 제시된 수준을 초과하여 구성하면 전원 공급 장치(PSU) 모드가 비중복으로 변경될 수 있습니다. 비중복 모드에서 전원 요구량이 설치된 시스템 전원 용량을 초과하면 BIOS가 프로세서 성능을 제한합니다.
2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 3. 전원 및 PSU에서 전원 케이블을 분리하고 주변 장치를 분리합니다. 단계 분리 레버를 누르고 핸들을 사용하여 시스템에서 PSU를 밀어 꺼냅니다. 노트: PSU를 분리하려면 상당한 힘이 필요할 수도 있습니다. 그림 40 . PSU 분리 및 설치 a. PSU b. 분리 레버 c. 핸들 다음 단계 1. PSU를 장착합니다. 2. 분리된 케이블과 주변 장치를 모두 다시 연결합니다. 3. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 전원 공급 장치(PSU) 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다.
단계 PSU가 완전히 장착되고 분리 레버가 제자리에 걸릴 때까지 PSU를 섀시에 밀어 넣습니다. 다음 단계 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 시스템 보드 트레이 시스템 보드 트레이 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나와 있는 안전 지침을 따릅니다. 단계 1. 고정 래치를 고정하는 나사를 분리합니다. 2. 고정 래치를 누르고 시스템 보드 트레이를 섀시에서 밀어 꺼냅니다. 그림 41 . 시스템 보드 트레이 분리 및 설치 a. 고정 래치 b. 나사 c.
시스템 보드 트레이 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 시스템 보드 트레이가 제자리에 고정될 때까지 섀시에 밀어 넣습니다. 2. 고정 래치를 고정하는 나사를 장착합니다. 관련 참조 안전 지침 페이지 60 시스템 보드 조립품 슬레드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다.
그림 42 . 슬레드 분리 그림 43 . 시스템 보드 조립품 분리 및 설치 1. 고정 래치 3. 핸들 2. 나사 4. 시스템 보드 조립품 다음 단계 1. 슬레드 또는 슬레드 보호물을 인클로저에 설치합니다. 2. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다.
슬레드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 3. 설치된 경우 인클로저에서 슬레드 보호물을 분리합니다. 노트: 슬레드 보호물을 분리하는 과정은 슬레드를 분리하는 과정과 동일합니다. 4. 십자 드라이버(# 2)를 준비합니다. 단계 1. 제자리에 잠길 때까지 슬레드를 인클로저에 밀어 넣습니다. 2. 고정 래치를 고정하는 나사를 장착합니다. 그림 44 . 슬레드 설치 다음 단계 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다.
냉각 덮개 냉각 덮개는 공기역학적으로 전체 시스템에 걸쳐 공기를 통과시킵니다. 시스템의 모든 중요 부품에 공기가 통과되고 진공기가 방열 판 전체 표면에서 공기를 빨아 들여 빠르게 냉각되도록 합니다. 냉각 덮개 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 3. 인클로저에서 슬레드를 분리합니다. 단계 1. 냉각 덮개의 한쪽 면에 있는 잠금 장치를 누르고 냉각 덮개를 들어 올려 슬레드에서 분리합니다. 그림 45 . 냉각 덮개 분리 2.
그림 46 . 냉각 덮개 분리 a. 냉각 덮개 b. 시스템 보드 조립품 다음 단계 1. 냉각 덮개를 설치합니다. 2. 슬레드를 인클로저에 설치합니다. 3. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 냉각 덮개 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 단계 1. 냉각 덮개를 슬레드에 삽입하고 래치를 슬레드 섀시의 잠금 슬롯과 정렬합니다.
그림 47 . 냉각 덮개 설치 3. 냉각 덮개를 시스템 보드 조립품에 장착합니다. 4개의 래치가 방열판 베이스에 제대로 맞물리고 래치가 딸깍 소리를 내며 제자리 에 고정되었는지 확인합니다. 노트: 냉각 덮개를 설치할 때 냉각 덮개의 화살표가 프로세서 1을 가리켜야 하며, 냉각 덮개의 평평한 면이 수평을 유지해야 합니다. 그림 48 . 설치된 냉각 덮개의 평면도 다음 단계 1. 시스템 보드 조립품을 설치합니다. 2. 주변 장치를 다시 장착하고 시스템을 전원 콘센트에 연결합니다. 3. 연결된 주변장치와 시스템을 켜십시오.
관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 설치 페이지 86 방열판 프로세서가 이 온도를 적절히 낮출 만큼 열을 충분히 분산시킬 수 없기 때문에 방열판이 프로세서로부터 열을 전달받아 분산시킵니 다. 방열판은 공기 등 주위의 냉각 매체와 접촉하는 표면적을 극대화하도록 설계됩니다. 열 그리스는 방열판과 프로세서의 히트 스프 레더 사이의 에어 갭을 메움으로써 방열판 성능을 향상시킵니다. 방열판 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 2개의 프로세서 방열판에 있는 풀프루프 핀이 안쪽을 향하도록 놓습니다. 1. 2. 3. 4.
그림 49 . 방열판 분리 및 설치 a. 나사(4개) b. 방열판 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 방열판 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 깨끗하고 보풀이 없는 천을 사용하여 방열판에 묻어 있는 내열 그리즈를 닦아냅니다. 2. 새 프로세서 중앙 상단에 새 열 그리즈를 고르게 바릅니다. 주의: 열 그리즈를 지나치게 많이 사용하면 프로세서 실드에 열 그리즈가 묻어 프로세서 소켓이 오염될 수 있습니다. 3. 프로세서에 방열판을 놓습니다. 4.
관련 태스크 슬레드 설치 페이지 86 프로세서 프로세서에는 메모리, 주변 장치 인터페이스 및 시스템의 기타 구성 요소가 포함되어 있습니다. 프로세서에는 여러 개의 코어가 있을 수 있습니다. 시스템에 여러 개의 프로세서가 있을 수 있습니다. C6320 시스템 보드는 E5-2600 v3 및 E5-2600 v4 프로세서 시리즈를 지원합니다. 프로세서 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 보드 조립품을 분리합니다. 3. 방열판을 분리합니다. 주의: 프로세서는 강한 압력으로 소켓 안에 고정되어 있습니다.
5. 소켓 분리 레버(2개) 6. CPU 소켓 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 방열판 분리 페이지 90 프로세서 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 프로세서를 하나만 설치하는 경우, 해당 프로세서는 반드시 프로세서 0에 설치해야 합니다(소켓 위치는 시스템 보드 커넥 터 섹션 참조). 노트: 프로세서를 업그레이드하는 경우, 시스템을 업그레이드하기 전에 Dell.com/support/home에서 최신 시스템 BIOS 버전을 다운로드하여 설치합니다. 시스템에 업데이트를 설치하려면, 파일 다운로드에 포함된 지침을 따릅니다. 1.
관련 개념 시스템 설치 프로그램 페이지 32 관련 참조 안전 지침 페이지 60 C6320 시스템 보드 커넥터 페이지 158 관련 태스크 슬레드 분리 페이지 84 방열판 설치 페이지 91 슬레드 설치 페이지 86 확장 카드 조립품 및 확장 카드 시스템의 확장 카드는 시스템 보드 라이저 카드의 확장 슬롯에 삽입하여 확장 버스를 통해 시스템에 기능을 추가할 수 있는 인쇄 회로 기판입니다. 노트: 누락되거나 지원되지 않는 확장 카드 라이저가 시스템 이벤트 로그(SEL) 이벤트를 기록합니다. 이는 시스템 전원이 켜지는 데 영향을 미치지 않으며 BIOS POST 메시지 또는 F1/F2 일시 중지가 표시되지 않습니다. 확장 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다.
그림 51 . 확장 카드 어셈블리 분리 a. 확장 카드 어셈블리 b. 나사(4개) c. 시스템 보드 어셈블리 3. 확장 카드를 고정하는 나사를 분리합니다. 4. 확장 카드의 모서리를 잡고 조심스럽게 라이저 카드에서 분리합니다. 노트: 카드를 영구적으로 분리하는 경우, 빈 확장 슬롯 입구에 확장 카드 슬롯 커버를 설치한 다음 확장 카드 래치를 닫습니 다. 노트: 시스템의 미국 연방 통신위원회(FCC) 인증을 유지하려면 필러 브래킷을 빈 확장 슬롯에 설치해야 합니다. 브래킷은 또 한 시스템 안으로 먼지 및 이물질이 들어오는 것을 막고 시스템 내부의 적절한 냉각 및 공기 흐름을 도와줍니다. 그림 52 . 확장 카드 분리 1. 확장 카드 슬롯 커버 3. 확장 카드 2. 나사 4.
관련 태스크 슬레드 분리 페이지 84 확장 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 확장 카드는 확장 카드 라이저의 슬롯에만 설치할 수 있습니다. 확장 카드를 시스템 보드의 라이저 커넥터에 직접 설치하 려 하지 마십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 확장 카드의 포장을 풀고 설치 준비를 합니다. 지침은 카드와 함께 제공된 설명서를 참조하십시오. 단계 1. 확장 카드 조립품을 고정하는 나사를 분리합니다. 2. 확장 카드 조립품을 시스템 보드 조립품에서 들어 올려 빼냅니다. 3. 필러 브래킷을 고정하는 나사를 분리합니다. 4.
PERC 카드 Dell PowerEdge C6320은 H330 및 12Gbps SAS HBA 카드를 지원합니다. Dell PowerEdge C6320은 열 제한 105W 이하의 프로세서의 경 우, H730도 지원합니다. PERC 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 단계 1. 시스템 보드에서 PERC 카드를 찾습니다. 2. 스토리지 컨트롤러 케이블을 분리하려면: a. 케이블을 카드에 고정하는 나사를 분리합니다. b.
다음 단계 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 라이저 카드 선택사양 라이저 카드 그림 53 . 1U 노드용 1U 라이저 카드 1. PCI-E Gen 3 x16 2. microSD 카드 소켓 라이저 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 5. 6. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 인클로저에서 슬레드를 분리합니다. 확장 카드 라이저 조립품을 분리합니다. 확장 카드가 설치되어 있는 경우 분리합니다. 십자 드라이버(# 2)를 준비합니다. 단계 1.
그림 54 . 라이저 카드 분리 및 설치 a. 나사(2개) b. 라이저 카드 c. 확장 카드 브래킷 다음 단계 1. 2. 3. 4. 5. 라이저 카드를 설치합니다. 확장 카드가 분리된 경우 설치합니다. 확장 카드 라이저 조립품을 설치합니다. 슬레드를 인클로저에 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 확장 카드 분리 페이지 94 라이저 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 5. 6. 안전 지침 섹션에 나열된 안전 지침을 따릅니다.
그림 55 . 라이저 카드 설치 다음 단계 1. 2. 3. 4. 확장 카드가 분리된 경우 설치합니다. 확장 카드 라이저 조립품을 설치합니다. 슬레드를 인클로저에 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 확장 카드 설치 페이지 96 슬레드 설치 페이지 86 선택 사양 메자닌 카드 C6320에서 지원되는 메자닌 카드 선택 사양은 다음과 같습니다. 표 29.
표 29. 지원되는 메자닌 카드 (계속) 유형 Card 듀얼 포트 SFP ConnectX4 LX 선택 사양인 LSI 2008 SAS 메자닌 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: LSI 2008 SAS 메자닌 카드는 1 프로세서 구성에서는 활성화되지 않는 시스템 보드의 PCI-E Gen3 x8 메자닌 슬롯 3에 장착 되어 있습니다. C6320 시스템 보드 커넥터 섹션을 참조하십시오. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 연결된 주변장치와 시스템을 끄십시오. 전원 콘센트에서 시스템을 분리하고 주변 장치도 분리합니다.
선택 사양인 LSI 2008 SAS 메자닌 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 시스템 보드 조립품에 LSI 2008 SAS 메자닌 카드를 놓습니다. 2. LSI 2008 SAS 메자닌 카드를 고정하는 나사를 설치합니다. 3. 모든 케이블을 LSI 2008 SAS 메자닌 카드에 다시 연결합니다. 다음 단계 1. 시스템 보드 조립품을 설치합니다. 2. 주변 장치를 다시 장착하고 시스템을 전원 콘센트에 연결합니다. 3. 연결된 주변장치와 시스템을 켜십시오.
표 30. LSI 2008 SAS 메자닌 카드를 위한 케이블 라우팅 (계속) 항목 케이블 시작(LSI 2008 SAS 메자닌 카드) 종료(시스템 보드) 미니 SAS 케이블 미니 SAS 커넥터 0 ~ 3(J3) 미니 SAS HD 커넥터 0 ~ 3 3. 케이블을 아래로 누르고, 케이블이 CPU 방열판의 높이보다 낮게 라우팅되는지 확인합니다. 그림 58 . LSI 2008 SAS 메자닌 카드를 위한 하향 케이블 라우팅(1U 노드) 1GbE 메자닌 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 59 . 확장 카드 브래킷 분리 및 설치 a. 나사(3개) b. 확장 카드 브래킷 c. 시스템 보드 조립품 3. 1GbE 메자닌 카드 조립품을 고정시키는 나사를 분리합니다. 4. 시스템 보드의 카드 브리지 보드에서 1GbE 메자닌 카드 조립품을 들어 올립니다. 그림 60 . 1GbE 메자닌 카드 조립품 분리 및 설치 1. 나사(4개) 3. 메자닌 카드 브리지 보드 5. 1GbE 메자닌 카드를 브래킷에 고정하는 나사를 분리합니다. 6. 1GbE 메자닌 카드를 브래킷에서 분리합니다. 104 시스템 구성 요소 설치 및 분리 2. 1GbE 메자닌 카드 조립품 4.
그림 61 . 1GbE 메자닌 카드 분리 및 설치 a. 나사(2개) b. 메자닌 카드 브래킷 c. 1GbE 메자닌 카드 관련 참조 안전 지침 페이지 60 C6320 시스템 보드 커넥터 페이지 158 관련 태스크 슬레드 분리 페이지 84 1GbE 메자닌 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 4개의 포트를 브래킷의 해당 포트 슬롯에 정렬하여 1GbE 메자닌 카드를 브래킷에 연결합니다. 2. 1GbE 메자닌 카드를 브래킷에 고정하는 나사를 설치합니다. 3.
4. 연결된 주변장치와 시스템을 켜십시오. 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 설치 페이지 86 10GbE 메자닌 카드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 10GbE 메자닌 카드는 1 프로세서 구성에서는 활성화되지 않는 시스템 보드의 PCI-E Gen3 x8 메자닌 슬롯 3에 장착되어 있 습니다. C6320 시스템 보드 커넥터 섹션을 참조하십시오. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 연결된 주변장치와 시스템을 끄십시오. 전원 콘센트에서 시스템을 분리하고 주변 장치도 분리합니다. 시스템 보드 조립품을 분리합니다.
그림 63 . 10GbE 메자닌 카드 조립품 분리 및 설치 1. 나사(4개) 3. 메자닌 카드 브리지 보드 2. 10GbE 메자닌 카드 조립품 4. 시스템 보드 조립품 6. 10GbE 메자닌 카드를 브래킷에 고정하는 나사를 분리합니다. 7. 10GbE 메자닌 카드를 브래킷에서 분리합니다. 그림 64 . 10GbE 메자닌 카드 분리 및 설치 a. 나사(2개) b. 메자닌 카드 브래킷 c.
10GbE 메자닌 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. 4개의 포트를 브래킷의 해당 포트 슬롯에 정렬하여 10GbE 메자닌 카드를 브래킷에 연결합니다. 2. 10GbE 메자닌 카드를 브래킷에 고정하는 나사를 설치합니다. 3. 10GbE 메자닌 카드 조립품을 시스템 보드 조립품의 카드 브리지 보드에 설치합니다. 4. 10GbE 메자닌 카드 조립품을 시스템 보드 조립품에 고정하는 나사를 설치합니다. 5. 확장 카드 브래킷을 시스템 보드 조립품에 넣습니다. 6. 확장 카드 브래킷을 고정시키는 나사를 설치합니다.
그림 65 . 메자닌 카드 브리지 보드 분리 및 설치 a. 시스템 보드 조립품 b. 메자닌 카드 브리지 보드 다음 단계 1. 2. 3. 4. 5. 6. 메자닌 카드 브리지 보드를 설치합니다. 메자닌 카드를 설치합니다. 메자닌 카드를 사용하지 않는 경우, 메자닌 브래킷을 설치합니다. 확장 카드 라이저 조립품을 설치합니다. 슬레드를 인클로저에 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 선택 사양인 LSI 2008 SAS 메자닌 카드 분리 페이지 101 1GbE 메자닌 카드 분리 페이지 103 10GbE 메자닌 카드 분리 페이지 106 메자닌 카드 브리지 보드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다.
2. 시스템 보드 조립품을 설치합니다. 3. 주변 장치를 다시 장착하고 시스템을 전원 콘센트에 연결합니다. 4. 연결된 주변장치와 시스템을 켜십시오. 관련 참조 안전 지침 페이지 60 관련 태스크 선택 사양인 LSI 2008 SAS 메자닌 카드 설치 페이지 102 1GbE 메자닌 카드 설치 페이지 105 10GbE 메자닌 카드 설치 페이지 108 시스템 보드 설치 페이지 117 슬레드 설치 페이지 86 시스템 메모리 시스템 메모리는 프로세서가 실행되는 지침을 보유하고 있습니다. 각 시스템 보드에는 프로세서 1 및 프로세서 2의 지원을 위한 최대 16개의 레지스터드 DDR4-2400MHz(채널당 2개의 메모리 모듈에서 2400MHz) 메모리 모듈 설치를 위한 16개의 DDR4 메모리 모듈 소 켓이 있습니다. 메모리 모듈의 위치는 C6320 시스템 보드 커넥터 섹션을 참조하십시오.
그림 66 . DIMM 슬롯 위치 표 31. 단일 프로세서를 위한 메모리 모듈 구성 프로세서 1 메모리 모듈 CHA CHB CHC CHD A1 A5 A2 A6 A3 A7 A4 A8 1 √ ‒ ‒ ‒ ‒ ‒ ‒ ‒ 2 √ ‒ √ ‒ ‒ ‒ ‒ ‒ 3 √ ‒ √ ‒ √ ‒ ‒ ‒ 4 √ ‒ √ ‒ √ ‒ √ ‒ 6 √ √ √ √ √ ‒ √ ‒ 8 √ √ √ √ √ √ √ √ 표 32.
표 33. 듀얼 프로세서를 위한 메모리 모듈 구성 (계속) 프로세서 2 12 √ √ √ √ √ ‒ √ ‒ 16 √ √ √ √ √ √ √ √ 메모리 모듈 분리 전제조건 경고: 시스템의 전원을 끈 후에도 한참 동안 메모리 모듈이 뜨거우므로 만지지 마십시오. 메모리 모듈을 다루기 전에 냉각될 때 까지 기다립니다. 메모리 모듈을 다룰 때에는 카드 모서리를 잡고 메모리 모듈의 구성 요소를 만지지 않도록 하십시오. 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 5. 6. 7. 안전 지침 섹션에 나열된 안전 지침을 따릅니다.
관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 냉각 덮개 분리 페이지 87 메모리 모듈 설치 전제조건 경고: 시스템의 전원을 끈 후에도 한참 동안 메모리 모듈이 뜨거우므로 만지지 마십시오. 메모리 모듈을 다루기 전에 냉각될 때 까지 기다립니다. 메모리 모듈을 다룰 때에는 카드 모서리를 잡고 메모리 모듈의 구성 요소를 만지지 않도록 하십시오. 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 섀시에서 슬레드를 분리합니다. 냉각 덮개를 분리합니다.
그림 69 . 메모리 모듈 설치 a. 메모리 모듈 b. 맞춤 키 c. 메모리 모듈 소켓 배출기(2) 다음 단계 냉각 덮개를 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 시스템 보드 조립품을 설치합니다. System Setup(시스템 설정)을 시작하려면 F2를 누르고 System Memory(시스템 메모리) 설정을 확인합니다. 값이 올바르지 않은 경우 메모리 모듈이 하나 이상 제대로 설치되지 않을 수 있습니다. 메모리 모듈이 해당 소켓에 단단히 장착되 었는지 확인합니다. 6. 시스템 진단 프로그램에서 시스템 메모리 검사를 실행합니다. 1. 2. 3. 4. 5. 관련 참조 안전 지침 페이지 60 관련 태스크 냉각 덮개 설치 페이지 88 슬레드 설치 페이지 86 시스템 배터리 시스템 배터리는 실시간 클럭에 전원을 공급하고 시스템의 BIOS 설정을 저장하는 데 사용됩니다. 시스템 배터리 장착 전제조건 경고: 새 배터리를 잘못 설치하면 폭발할 수 있습니다.
2. 3. 4. 5. 6. 연결된 주변장치와 시스템을 끄십시오. 전원 콘센트 및 주변 장치에서 시스템을 분리합니다. 시스템 보드 조립품을 분리합니다. 냉각 덮개를 분리합니다. 확장 카드 조립품을 분리합니다. 단계 1. 배터리 래치를 밀고 커넥터에서 배터리를 들어 올려 빼냅니다. 주의: 배터리 커넥터의 손상을 방지하려면 배터리를 설치하거나 분리하는 경우 커넥터를 단단히 잡아야 합니다. 2. "+"가 배터리 커넥터의 양극 쪽을 향한 상태에서 새 배터리를 잡습니다. 3. 제자리에 장착될 때까지 배터리를 배터리 홀더에 삽입합니다. 그림 70 . 시스템 배터리 장착 a. 시스템 배터리 b. 전지 커넥터의 음극 쪽 c. 전지 래치 다음 단계 1. 2. 3. 4. 5. 6. 시스템 보드 조립품을 장착합니다. 시스템을 전원 콘센트에 다시 연결합니다. 연결된 주변장치와 시스템을 켜십시오. 시스템 설정 프로그램을 시작하여 배터리가 올바로 작동하는지 확인합니다. 시스템 설정 섹션을 참조하십시오.
확장 카드 분리 페이지 94 슬레드 설치 페이지 86 시스템 보드 시스템 보드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 시스템 보드에서 TPM 플러그인 모듈을 분리하려고 하지 마십시오. TPM 플러그인 모듈이 일단 설치된 후에는 해당 특정 시스템 보드에 암호화로 바인딩됩니다. 설치된 TPM 플러그인 모듈을 제거하려고 시도하면 암호화된 바인딩이 망가지며, 다시 설치하거나 다른 시스템 보드에 설치할 수 없습니다. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다.
c. 시스템 보드 조립품 다음 단계 1. 시스템 보드를 교체하는 경우, 이전 시스템 보드의 SAS 커넥터 프로텍터를 재사용합니다. 노트: 새 시스템 보드 또는 교체용 시스템 보드에서는 SAS 커넥터 프로텍터가 제공되지 않습니다.. SAS 커넥터 프로텍터와 함께 이전 시스템 보드를 반환하지 마십시오. 2. 시스템 보드를 장착합니다. 3. 분리한 모든 구성 요소 및 케이블을 설치합니다. 4. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 슬레드 분리 페이지 84 냉각 덮개 분리 페이지 87 확장 카드 분리 페이지 94 방열판 분리 페이지 90 메모리 모듈 분리 페이지 112 선택 사양인 LSI 2008 SAS 메자닌 카드 분리 페이지 101 1GbE 메자닌 카드 분리 페이지 103 10GbE 메자닌 카드 분리 페이지 106 시스템 보드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
b. 서비스 태그를 백업 플래시 디바이스에 백업하지 않은 경우 시스템 서비스 태그를 수동으로 입력합니다. 자세한 내용은 시스 템 서비스 태그 입력 섹션을 참조하십시오. c. BIOS 및 iDRAC 버전을 업데이트합니다. d. TPM(Trusted Platform Module)을 재활성화합니다. 자세한 내용은 dell.com/ TPM(Trusted Platform Module)을 재활성화 섹션을 참조하십시오. 관련 참조 안전 지침 페이지 60 관련 태스크 프로세서 분리 페이지 92 프로세서 설치 페이지 93 메모리 모듈 분리 페이지 112 메모리 모듈 설치 페이지 113 방열판 설치 페이지 91 확장 카드 설치 페이지 96 선택 사양인 LSI 2008 SAS 메자닌 카드 설치 페이지 102 1GbE 메자닌 카드 설치 페이지 105 10GbE 메자닌 카드 설치 페이지 108 냉각 덮개 설치 페이지 88 슬레드 설치 페이지 86 시스템 설정을 사용하여 시스템 서비스 태그 입력 단계 1.
온보드 SATA 케이블을 위한 케이블 라우팅(1U 노드) 단계 1. 온보드 SATA 케이블을 시스템 보드에 연결하고, 케이블의 다른 쪽 끝을 해당되는 시스템 보드 커넥터에 연결합니다. 그림 72 . 온보드 SATA 케이블을 위한 케이블 라우팅(1U 노드) 표 34. 온보드 SATA 케이블을 위한 케이블 라우팅(1U 노드) 항목 케이블 시작(시스템 보드) 종료(시스템 보드) 온보드 SATA 케이블 온보드 SATA 출력 커넥터 0 SAS/SATA 입력 커넥터 0 온보드 SATA 케이블 온보드 SATA 커넥터 4, 5 SAS/SATA 입력 커넥터 4, 5 2. 케이블을 아래로 눌러 케이블이 프로세서 방열판의 높이보다 낮게 라우팅해야 합니다. 그림 73 .
노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자만 수행할 수 있습니다. TPM(Trusted Platform Module)설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 섹션에 나와 있는 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 단계 1. 시스템 보드에서 TPM 커넥터를 찾습니다. 노트: 시스템 보드에서 TPM 커넥터를 찾으려면 시스템 보드 커넥터 섹션을 참조하십시오. 2. TPM의 가장자리 커넥터를 TPM 커넥터 슬롯에 맞춥니다. 3.
TXT 사용자를 위한 TPM 초기화 단계 1. 시스템를 부팅하는 동안 F2를 눌러 시스템 설정으로 들어갑니다. 2. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS) > System Security Settings(시스템 보안 설정)를 클릭합니다. 3. TPM Security(TPM 보안) 옵션에서 On with Pre-boot Measurements(사전 부팅으로 켜기)를 선택합니다. 4. TPM Command(TPM 명령) 옵션에서 Activate(활성화)를 선택합니다. 5. 설정을 저장합니다. 6. 시스템를 다시 시작합니다. 7. System Setup(시스템 설정)으로 다시 전환됩니다. 8. System Setup Main Menu(시스템 설정 기본 메뉴) 화면에서 System BIOS(시스템 BIOS) > System Security Settings(시스템 보안 설정)를 클릭합니다. 9.
그림 75 . 전원 케이블 덮개 분리 및 설치 a. 나사 b. 전원 케이블 덮개 4. 전원 케이블을 PDB 1에 고정하는 나사를 분리합니다. 그림 76 . 전원 케이블 분리 및 설치 a. 나사(4개) b. 전원 케이블(4개) 5. PDB 1을 시스템에 고정하는 나사를 분리합니다. 6. 시스템에서 PDB 1을 들어 올립니다.
그림 77 . PDB 1 분리 및 설치 a. PDB 1 b. 나사(8개) 7. PDB 커넥터 브리지 보드를 시스템에서 들어 올립니다. 8. PDB 2에서 모든 케이블을 분리합니다. 9. 전원 케이블 덮개를 PDB 2에 고정하는 나사를 분리합니다. 10. PDB 2의 잠금 구멍에서 수직으로 전원 케이블 덮개를 들어 올립니다. 그런 다음, PDB 2를 들어 올려 빼냅니다. 11. PDB 2에서 4개의 전원 케이블을 고정하는 나사를 분리합니다. 12. PDB 2에서 4개의 전원 케이블을 분리합니다. 13. PDB 2를 시스템에 고정하는 나사를 분리합니다. 14. PDB 2를 들어 올려 시스템에서 꺼냅니다. 다음 단계 1. PDB를 장착합니다. 2. PSUs를 장착합니다. 3. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다.
4. 배전 보드 1(PDB 1)을 분리합니다. 단계 1. PDB 커넥터를 시스템에서 들어 올립니다. 그림 78 . PDB 커넥터 분리 및 설치 a. PDB 커넥터 b. PDB 2 2. PDB 2에서 모든 케이블을 분리합니다. 3. 전원 케이블 덮개를 PDB에 고정하는 나사를 분리합니다. 4. PDB 2에서 전원 케이블 덮개를 분리합니다. 5. 전원 케이블을 PDB 2에 고정하는 나사를 분리합니다. 6. PDB 2를 시스템에 고정하는 나사를 분리합니다. 7. PDB 2를 들어 올려 시스템에서 꺼냅니다. 그림 79 . PDB 2 분리 및 설치 a. 나사(4개) b.
관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 시스템 덮개 분리 페이지 62 배전 보드 2 분리 페이지 123 배전 보드 2 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 분리한 경우, 배전 보드 1(PDB 1)을 장착하기 전에 배전 보드 2(PDB 2)와 배전 보드 커넥터를 장착해야 합니다. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 단계 1. PDB 2의 나사 구멍을 섀시의 나사 구멍에 맞춥니다. 노트: PDB 2를 설치하려면 설치 중에 보드의 각도를 맞춥니다. 2. PDB 2를 시스템 보드에 고정하는 나사를 설치합니다. 3.
3. 나사를 사용하여 전원 케이블을 PDB 1에 고정합니다. 4. 모든 케이블을 PDB 1에 연결합니다. 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대로 배선해야 합니다. 다음 단계 1. 전원 공급 장치를 설치합니다. 2. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 덮개 장착 페이지 63 시스템 내부 작업을 마친 후에 페이지 61 배전판의 케이블 배선 이 작업 정보 그림 80 . 케이블 라우팅 − 배전 보드 1(상단) 표 35.
표 35. 케이블 라우팅 − 배전 보드 1(상단) (계속) 항목 케이블 시작(배전 보드) 펌웨어 후면판 제어 케이블 하드 드라이브 후면판 제어 커 넥터(J17) 후면판 시스템 팬 케이블 시스템 팬 커넥터(J9) 냉각 팬 12 V 전원 케이블 배전 보드 1/2 중앙판 접지 전원 케이블 배전 보드 1/2 중앙판 케이블 시작(배전 보드 2) 펌웨어 접지 전원 케이블 배전 보드 1/2 중앙판 12V 전원 케이블 배전 보드 1/2 중앙판 그림 81 . 케이블 라우팅−배전 보드 2(하단) 표 36. 케이블 라우팅−배전 보드 2(하단) 항목 중앙판 3.5인치 하드 드라이브 구성에서 2개의 중앙판은 시스템 보드를 3.5인치 하드 드라이브 후면판에 연결합니다. 2.5인치 하드 드라이브 구성에서 2개의 중앙판은 시스템 보드를 확장기 구성용 2.5인치 하드 드라이브 후면판에 연결합니다.
그림 82 . 중앙판 커넥터 1. 배전 보드 1용 2x17핀 제어 커넥터 2. 시스템 보드 3 및 4용 미니 SAS 커넥터(하드 드라이브 5, 6) 3. 시스템 보드 3 및 4용 미니 SAS 커넥터(하드 드라이브 1, 2, 3, 4. 시스템 보드 1 및 2용 미니 SAS 커넥터(하드 드라이브 5, 6) 4) 5. 시스템 보드 1 및 2용 미니 SAS 커넥터(하드 드라이브 1, 2, 3, 4) 중앙판 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 5. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다.
그림 83 . 전원 케이블 덮개 분리 및 설치 a. 나사 b. 전원 케이블 덮개 4. 상단 중앙판에 전원 케이블을 고정하는 나사를 분리합니다. 그림 84 . 전원 케이블 분리 및 설치 a. 전원 케이블(4개) b. 나사(4개) 5. 상단 중앙판을 중앙판 홀더에 고정하는 나사를 분리합니다. 6. 상단 중앙판을 들어 꺼냅니다.
그림 85 . 상단 중앙판 분리 및 설치 a. 나사(8개) b. 상단 중앙판 7. 중앙판 홀더 지지대를 섀시에 고정하는 나사를 분리합니다. 8. 중앙판 홀더 지지대를 섀시에서 들어 꺼냅니다. 그림 86 . 중앙판 홀더 지지대 분리 및 설치 a. 나사(3개) b.
그림 87 . 중앙판 홀더 지지대 분리 9. 중앙판 홀더를 섀시에 고정하는 나사를 분리합니다. 10. 중앙판 홀더를 섀시에서 들어 꺼냅니다. 그림 88 . 중앙판 홀더 분리 및 설치 a. 나사(6개) b.
그림 89 . 중앙판 홀더 분리 11. 모든 케이블을 하단 중앙판에서 분리합니다. 노트: 시스템에서 케이블을 분리할 때 섀시의 케이블 라우팅에 주목하십시오. 이러한 케이블을 장착할 때 조여지거나 구겨지 지 않도록 적절하게 라우팅합니다. 12. 전원 케이블 덮개를 하단 중앙판에 고정하는 나사를 분리합니다. 13. 하단 중앙판에서 전원 케이블 덮개를 분리합니다. 14. 전원 케이블을 하단 중앙판에 고정하는 나사를 분리합니다. 15. 하단 중앙판에서 4개의 전원 케이블을 분리합니다. 16. 하단 중앙판을 섀시에 고정하는 나사를 분리합니다. 17. 하단 중앙판을 섀시에서 들어 꺼냅니다. 그림 90 . 하단 중앙판 분리 및 설치 a. 나사(8개) b. 하단 중앙판 다음 단계 1. 중앙판을 설치합니다. 2. 냉각 팬 케이지를 설치합니다. 3. 시스템 보드를 장착합니다.
4. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 시스템 덮개 분리 페이지 62 슬레드 분리 페이지 84 냉각 팬 분리 페이지 64 중앙판 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 하단 중앙판을 분리하는 절차는 상단 중앙판을 분리하는 절차와 비슷합니다. 노트: 케이블이 조여지거나 구겨지지 않도록 섀시에 케이블을 제대로 배선해야 합니다. 1. 2. 3. 4. 5. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다.
2. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 냉각 팬 설치 페이지 65 슬레드 설치 페이지 86 시스템 덮개 장착 페이지 63 시스템 내부 작업을 마친 후에 페이지 61 케이블 라우팅 - 중앙판에서 하드 드라이브 후면판으로 이 작업 정보 그림 91 . 케이블 라우팅 - 상단 중앙판에서 12 x 3.5인치 하드 드라이브 구성용 후면판으로 표 37. 케이블 라우팅 - 상단 중앙판에서 12 x 3.
그림 92 . 케이블 라우팅 - 하단 중앙판에서 12 x 3.5인치 하드 드라이브 구성용 후면판으로 표 38. 케이블 라우팅 - 하단 중앙판에서 12 x 3.5인치 하드 드라이브 구성용 후면판으로 항목 케이블 시작(하단 중앙판) 종료(후면판) 하드 드라이브 후면판 케이블 시스템 보드 2용 미니 SAS 커넥 시스템 보드 2용 SATA2 하드 터(하드 드라이브 2, 2, 3, 4)(J1) 드라이브 커넥터 1, 2, 3(상단 ~ 하단) 하드 드라이브 후면판 케이블 시스템 보드 4용 미니 SAS 커넥 시스템 보드 4용 SATA2 하드 터(하드 드라이브 1, 2, 4, 4)(J3) 드라이브 커넥터 1, 2, 3(상단 ~ 하단) 그림 93 . 케이블 라우팅 - 상단 중앙판에서 24 x 2.
표 39. 케이블 라우팅 - 상단 중앙판에서 24 x 2.
표 40. 케이블 라우팅 - 하단 중앙판에서 24 x 2.5인치 하드 드라이브 구성용 후면판으로 (계속) 항목 케이블 시작(하단 중앙판) 종료(후면판) 하드 드라이브 후면판 케이블 시스템 보드 4용 미니 SAS 커넥 시스템 보드 4용 SATA2 하드 터(하드 드라이브 5와 6)(J4) 드라이브 커넥터 5 ~ 6(오른쪽 ~ 왼쪽) 중앙판에서 확장기 구성을 위한 2.5인치 하드 드라이브 후면판으로 케이블 라우팅 그림 95 . 케이블 라우팅 − 상단 중앙판에서 확장기 구성을 위한 2.5인치 하드 드라이브까지 표 41. 케이블 라우팅 − 상단 중앙판에서 확장기 구성을 위한 2.
그림 96 . 케이블 라우팅 − 하단 중앙판에서 확장기 구성을 위한 2.5인치 하드 드라이브까지 표 42. 케이블 라우팅 − 하단 중앙판에서 확장기 구성을 위한 2.5인치 하드 드라이브까지 항목 케이블 시작(하단 중앙판) 종료(확장기 카드) 하드 드라이브 후면판 케이블 시스템 보드 2용 미니 SAS 커넥 시스템 보드 2용 미니 SAS 커넥 터(J4) 터(4 ~ 7) 하드 드라이브 후면판 케이블 시스템 보드 4용 미니 SAS 커넥 시스템 보드 4용 미니 SAS 커넥 터(J6) 터(12 ~ 15) 하드 드라이브 후면판 서버는 후면판을 이용하여 핫 스왑 가능한 하드 드라이브를 연결합니다. 후면판에는 케이블 없이 하드 드라이브 소켓에 직접 연결되 는 핀이 있습니다. 여기에는 하나의 디스크 어레이 컨트롤러를 연결할 수 있는 단일 커넥터 또는 하나 이상의 컨트롤러에 연결할 수 있는 여러 커넥터가 있을 수 있습니다. 그림 97 . 3.5인치 하드 드라이브 후면판의 전면 1. 3.5인치 후면판 3.
그림 98 . 3.5인치 하드 드라이브 후면판의 후면 1. 3. 5. 7. 9. 11. 전원 공급 장치 1용 후면판 전원 커넥터 시스템 보드 4용 SGPIO 커넥터 4 시스템 보드 2용 SGPIO 커넥터 2 후면판 점퍼 시스템 보드 2용 SATA2 및 SAS 커넥터 1, 2, 3(상단 ~ 하단) 시스템 보드 4용 SATA2 및 SAS 커넥터 1, 2, 3(상단 ~ 하단) 2. 4. 6. 8. 10. 12. 1x8핀 팬 컨트롤러 보드 커넥터 시스템 보드 3용 SGPIO 커넥터 3 시스템 보드 1용 SGPIO 커넥터 1 시스템 보드 1용 SATA2 및 SAS 커넥터 1, 2, 3(상단 ~ 하단) 시스템 보드 3용 SATA2 및 SAS 커넥터 1, 2, 3(상단 ~ 하단) 전원 공급 장치 2용 후면판 전원 커넥터 그림 99 . 2.5인치 하드 드라이브 후면판의 전면 1. 시스템 보드 1용 하드 드라이브 커넥터 1 ~ 6(왼쪽 ~ 오른쪽) 3.
하드 드라이브 후면판 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 드라이브 및 후면판의 손상을 방지하려면 후면판을 분리하기 전에 시스템에서 하드 드라이브를 분리해야 합니다. 주의: 하드 드라이브를 동일한 위치에 장착할 수 있도록 분리하기 전에 각 하드 드라이브의 번호를 기록하고 임시적으로 레이블 을 붙여야 합니다. 노트: 2.5인치 SATA2 및 SAS 후면판 분리 절차는 3.5인치 하드 드라이브 시스템용 후면판 분리 절차와 비슷합니다. 노트: 시스템에서 케이블을 분리할 때 섀시 케이블의 라우팅을 관찰하십시오.
그림 102 . 하드 드라이브 케이지 분리 및 설치 a. 하드 드라이브 케이지 b. 제어판 조립품(2개) c. 나사(2개) 5. 하드 드라이브 후면판에 연결된 모든 케이블을 분리합니다. 6. 후면판을 하드 드라이브 케이지에 고정하는 나사를 분리합니다. 7. 하드 드라이브 케이지에서 후면판을 분리합니다. 그림 103 . 하드 드라이브 케이지에서 후면판 분리 및 설치 a. 하드 드라이브 케이지 b. 3.5인치 후면판 c. 나사(10개) 다음 단계 1. 하드 드라이브 후면판을 설치합니다. 2. 하드 드라이브를 설치합니다. 3. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다.
관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 하드 드라이브 캐리어 분리 페이지 69 시스템 덮개 분리 페이지 62 하드 드라이브 후면판 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 드라이브 및 후면판의 손상을 방지하려면 후면판을 분리하기 전에 시스템에서 하드 드라이브를 분리해야 합니다. 주의: 하드 드라이브를 동일한 위치에 장착할 수 있도록 분리하기 전에 각 하드 드라이브의 번호를 기록하고 임시적으로 레이블 을 붙여야 합니다. 노트: 케이블이 조여지거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 적절하게 배선해야 합니다. 1. 2. 3. 4.
그림 104 . 후면판 전면 1. 하드 드라이브 커넥터 1 ~ 24(왼쪽 ~ 오른쪽) 2. 확장기 구성을 위한 2.5인치 후면판 그림 105 . 후면판 후면 1. 전원 공급 장치 1용 후면판 전원 커넥터 3. 확장기 - 카드 커넥터 2 2. 확장기 - 카드 커넥터 1 4. 전원 공급 장치 2용 후면판 전원 커넥터 그림 106 . 2.5인치 하드 드라이브 확장기 카드의 평면도 1. 전력 제어 커넥터 3. 미니 SAS 커넥터(12 ~ 15) 5. 미니 SAS 커넥터(0 ~ 3) 2. 미니 SAS 커넥터(4 ~ 7) 4. 미니 SAS 커넥터(8 ~ 11) 다음은 2.5인치 하드 드라이브 확장기 구성을 위한 SATA2 및 SAS 후면판의 교체 절차입니다. 이 구성은 최대 4개의 시스템 보드에 적 용 가능하며, 최대 24개의 하드 드라이브를 지원합니다. 자세한 내용은 Dell.com/support의 Drivers & Downloads(드라이버 및 다 운로드)에 있는 HDD 조닝 구성 도구를 참조하십시오.
노트: 시스템에서 케이블을 분리할 때 섀시에서 케이블의 라우팅을 관찰합니다. 장착을 할 때는 케이블이 조이거나 구겨지지 않 도록 올바르게 라우팅을 해야 합니다. 1. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 3. 모든 하드 드라이브를 분리합니다. 단계 1. 후면판과 확장 카드에서 모든 케이블을 분리합니다. 그림 107 . 확장기 구성을 위한 2.5인치 하드 드라이브 후면판의 후면 1. 전원 공급 장치 1용 후면판 전원 커넥터 3. 확장기 - 카드 커넥터 2 2. 확장기 - 카드 커넥터 1 4. 전원 공급 장치 2용 후면판 전원 커넥터 그림 108 . 확장기 카드의 평면도 1. 전력 제어 커넥터 3. 미니 SAS 커넥터(12 ~ 15) 5. 미니 SAS 커넥터(0 ~ 3) 2. 배전 보드에서 제어판 케이블을 분리합니다. 3. 하드 드라이브 케이지를 섀시에 고정시키는 나사를 분리합니다. 144 시스템 구성 요소 설치 및 분리 2.
그림 109 . 확장기 구성을 위한 2.5인치 하드 드라이브 후면판 분리 및 설치 a. 하드 드라이브 케이지 b. 나사(2개) 4. 제어판을 섀시에 고정시키는 나사를 제거합니다. 5. 섀시에서 하드 드라이브 케이지를 분리합니다. 그림 110 . 확장기 구성을 위한 2.5인치 하드 드라이브 케이지의 분리 및 설치 a. 하드 드라이브 케이지 b. 제어판 조립품(2개) c. 나사(2개) 6. 확장기 카드 조립품을 하드 드라이브 케이지에 고정하는 나사를 분리합니다.
그림 111 . 확장기 카드 조립품을 하드 드라이브 케이지에 고정하는 나사의 분리 및 설치 a. 하드 드라이브 케이지 b. 나사(6개) 7. 확장기 카드 조립품을 하드 드라이브 케이지에서 분리합니다. 그림 112 . 하드 드라이브 케이지에서 2.5인치 하드 드라이브 확장기 카드 조립품 분리 및 설치 a. 하드 드라이브 케이지 b. 확장기 카드 조립품 8. 확장기 구성을 위한 후면판을 하드 드라이브 케이지에 고정하는 나사를 분리합니다. 9. 하드 드라이브 케이지에서 확장기 구성을 위한 후면판을 분리합니다.
그림 113 . 확장기 구성을 위한 후면판을 설치하고 하드 드라이브 케이지에서 분리하기 a. 하드 드라이브 케이지 b. 확장기 구성을 위한 2.5인치 하드 드라이브 후면판 c. 나사(11개) 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 하드 드라이브 캐리어 분리 페이지 69 시스템 덮개 분리 페이지 62 확장기 구성을 위한 2.5인치 하드 드라이브 후면판 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 케이블이 조이거나 구겨지지 않도록 섀시의 탭을 통해 케이블을 제대로 배선해야 합니다.
다음 단계 1. 하드 드라이브를 설치합니다. 2. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 덮개 장착 페이지 63 하드 드라이브 캐리어에 하드 드라이브 설치 페이지 71 시스템 내부 작업을 마친 후에 페이지 61 제어판 제어판을 사용하여 서버에 대한 입력을 수동으로 제어할 수 있습니다. 일반적으로 제어판에는 USB 및 VGA 포트와 함께 NMI 단추, 전 원 단추 및 LCD 디스플레이 장치(옵션) 또는 진단 표시등이 있습니다. 제어판 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 114 . 왼쪽 제어판 조립품 분리 그림 115 .
그림 116 . 제어판 조립품 분리 및 설치 a. 제어판 조립품 b. 나사(2개) 4. 제어판 조립품의 고정 고리를 한쪽으로 밉니다. 5. 제어판 조립품에서 제어판을 분리합니다. 6. 제어판 케이블을 분리하십시오. 그림 117 . 제어판 분리 및 설치 a. 제어판 조립품 b. 제어판 c. 고정 고리 다음 단계 1. 제어판 조립품을 설치합니다. 2. 하드 드라이브 케이지를 인클로저에 설치합니다. 하드 드라이브 케이지를 설치하는 절차는 후면판을 설치하는 절차와 유사합니 다. 3. 분리된 케이블을 다시 연결합니다. 4. 분리한 모든 하드 드라이브를 설치합니다. 5. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다.
관련 참조 안전 지침 페이지 60 관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 하드 드라이브 캐리어 분리 페이지 69 시스템 덮개 분리 페이지 62 제어판 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 시스템에서 케이블을 분리할 때 섀시 케이블의 라우팅을 관찰하십시오. 이러한 케이블을 장착할 때 조여지거나 구겨지지 않도록 적절하게 라우팅해야 합니다. 노트: 케이블을 고정하는 데 추가 테이프가 필요할 수 있습니다. 1. 2. 3. 4. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 제어판을 분리합니다.
그림 119 . 오른쪽 제어판 설치 4. 제어판 조립품을 하드 드라이브 케이지에 고정하는 나사를 설치합니다. 5. 제어판 조립품을 섀시에 고정하는 나사를 설치합니다. 다음 단계 1. 2. 3. 4. 5. 하드 드라이브 케이지를 인클로저에 설치합니다. 모든 케이블을 후면판에 연결합니다. 배전 보드에 제어판 케이블을 연결합니다. 분리한 모든 하드 드라이브를 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 덮개 장착 페이지 63 하드 드라이브 캐리어에 하드 드라이브 설치 페이지 71 시스템 내부 작업을 마친 후에 페이지 61 센서 보드 열 센서 보드는 인클로저 주변의 온도를 모니터링하는 데 사용됩니다. 3.5인치 하드 드라이브 시스템 센서 보드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
3. 모든 하드 드라이브를 분리합니다. 4. 후면판에서 모든 케이블을 분리합니다. 5. 배전 보드에서 전면 패널 케이블을 분리합니다. 단계 1. 섀시에서 하드 드라이브 케이지를 분리합니다. 2. 센서 보드에서 케이블을 분리합니다. 3. 하드 드라이브 케이지에 센서 보드를 고정하는 나사를 분리합니다. 4. 하드 드라이브 케이지에서 센서 보드를 분리합니다. 그림 120 . 센서 보드 분리 및 설치 a. 센서 보드 b. 나사 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 내부 작업을 시작하기 전에 페이지 61 하드 드라이브 캐리어 분리 페이지 69 시스템 덮개 분리 페이지 62 3.5인치 하드 드라이브 시스템 센서 보드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다.
다음 단계 1. 2. 3. 4. 5. 6. 하드 드라이브 케이지를 섀시에 설치합니다. 하드 드라이브 케이지를 섀시에 고정하는 나사를 설치합니다. 모든 케이블을 후면판에 연결합니다. 배전 보드에 전면 패널 케이블을 연결합니다. 하드 드라이브를 설치합니다. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 관련 참조 안전 지침 페이지 60 관련 태스크 시스템 덮개 장착 페이지 63 하드 드라이브 캐리어에 하드 드라이브 설치 페이지 71 시스템 내부 작업을 마친 후에 페이지 61 3.5인치 하드 드라이브 시스템 센서 보드 및 제어판의 케이블 라우팅 단계 1. 배전 보드 1의 커넥터에 센서 보드와 제어판 2를 위한 Y형 케이블을 연결하고, 센서 보드와 제어판 2의 커넥터 각각에 케이블의 반 대쪽 양 끝을 연결합니다. 2. 배전 보드 1의 커넥터에 제어판 케이블을 연결하고, 제어판 1의 커넥터에 케이블의 다른 쪽 끝을 연결합니다. 그림 121 . 케이블 라우팅 − 센서 보드 및 제어판 표 43.
표 43. 3.5인치 하드 드라이브 시스템 센서 보드 및 제어판의 케이블 라우팅 (계속) 항목 케이블 시작(배전 보드) 종료(센서 보드 및 제어판) 전면 패널 케이블 전면 패널 커넥터(J18) 전면 패널 1 2.5인치 하드 드라이브 시스템 센서 보드 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 드라이브 및 후면판의 손상을 방지하려면 후면판을 분리하기 전에 시스템에서 하드 드라이브를 분리해야 합니다. 주의: 하드 드라이브를 동일한 위치에 장착할 수 있도록 분리하기 전에 각 하드 드라이브의 번호를 기록하고 임시적으로 레이블 을 붙여야 합니다.
2.5인치 하드 드라이브 시스템 센서 보드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 케이블이 조이거나 구겨지지 않도록 섀시에 케이블을 제대로 배선해야 합니다. 1. 2. 3. 4. 5. 6. 안전 지침 섹션에 나열된 안전 지침을 따릅니다. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 모든 하드 드라이브를 분리합니다. 하드 드라이브 케이지를 분리합니다. 후면판과 센서 보드에 연결된 모든 케이블을 분리합니다. 십자 드라이버(# 1)를 준비합니다. 단계 1. 센서 보드를 센서 보드 홀더에 설치하고 나사로 고정합니다. 2.
그림 122 . 케이블 라우팅 − 센서 보드 및 제어판 표 44.
7 점퍼 및 커넥터 이 주제에서는 점퍼에 대한 특정 정보를 제공합니다. 또한 점퍼 및 스위치에 대한 몇 가지 기본 정보를 제공하고 시스템의 다양한 보 드에 있는 커넥터에 대해 설명합니다. 시스템 보드의 점퍼는 시스템 및 설정 암호를 비활성화하는 데 도움이 됩니다. 구성 요소와 케 이블을 올바르게 설치하려면 시스템 보드의 커넥터를 알고 있어야 합니다. 주제: C6320 시스템 보드 커넥터 LSI 2008 SAS 메자닌 카드 커넥터 Powerville 이중 포트 1GbE Twinville 이중 포트 10GbE 배전 보드 1 커넥터 배전 보드 2 커넥터 센서 보드 커넥터 점퍼 설정 • • • • • • • • C6320 시스템 보드 커넥터 그림 123 . C6320 시스템 보드 커넥터 표 45.
표 45.
LSI 2008 SAS 메자닌 카드 커넥터 그림 124 . LSI 2008 SAS 메자닌 카드 커넥터 1. 메자닌 카드 커넥터 3. 미니 SAS 커넥터(포트 4 ~ 7) 2. LSI 2008 메자닌 카드 4. 미니 SAS 커넥터(포트 0 ~ 3) Powerville 이중 포트 1GbE 그림 125 . Powerville 이중 포트 1GbE 커넥터 1. Powerville 이중 포트 1GbE 카드 3. NIC 1 커넥터 160 점퍼 및 커넥터 2. 메자닌 카드 커넥터 4.
Twinville 이중 포트 10GbE 그림 126 . Twinville 이중 포트 10GbE 커넥터 1. Twinville 이중 포트 10GbE 카드 3. NIC 1 커넥터 2. 메자닌 카드 커넥터 4. NIC 2 커넥터 배전 보드 1 커넥터 그림 127 . 배전 보드 1 커넥터 1. 3. 5. 7. 시스템 보드 1 및 2용 제어판 커넥터 하드 드라이브 후면판 전원 커넥터 1 10핀 제어 커넥터 1개 시스템 보드용 17핀 제어 커넥터 2개 2. 4. 6. 8. 시스템 팬 커넥터 하드 드라이브 후면판 전원 커넥터 2 시스템 보드 2 및 4용 17핀 제어 커넥터 2개 하드 드라이브 후면판에 연결되는 8핀 제어 커넥터 1개 1및3 9.
배전 보드 2 커넥터 그림 128 . 배전 보드 2 커넥터 1. 브리지 카드 커넥터 2. 10핀 제어 커넥터 1개 센서 보드 커넥터 그림 129 . 센서 보드 커넥터 1. 전원 커넥터 2. 센서 보드 점퍼 설정 PowerEdge C6320 시스템 보드의 점퍼 설정 각 PowerEdge C6320 시스템 보드에 설치된 시스템 구성 점퍼의 기능은 다음과 같습니다.
그림 130 . C6320 시스템 보드의 시스템 구성 점퍼 표 46. C6320시스템 보드의 시스템 구성 점퍼 점퍼 기능 사용 안 함(기본 상태) 활성 상태 1 BIOS Recovery 핀 없음 핀 1-2 2 NVRAM 지우기 핀 없음 핀 1-2 3 PWRD_EN 핀 1-2 핀 2-3 4 ME_FM 복구 핀 없음 핀 1-2 후면판 점퍼 설정 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 3.5인치 하드 드라이브 후면판과 2.5인치 하드 드라이브 후면판에 설치된 점퍼의 기능은 동일합니다. 다음은 3.5-인치 HDD 후면판에 설치된 점퍼 사용의 예시입니다.
8 시스템 문제 해결 안전 제일 - 사용자 및 시스템 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 해결 방법에 대한 검증은 출하 시 제공되는 하드웨어 구성을 사용하여 수행되었습니다.
노트: PCI-E 슬롯1과 메자닌 슬롯을 사용하려면 프로세서 1이 설치되어야 합니다. PCI-E 슬롯 3을 사용하려면 프로세서 1과 프로 세서 2가 모두 설치되어야 합니다. 시스템 시작 오류 문제 해결 UEFI 부팅 관리자에서 운영 체제를 설치한 후 시스템를 BIOS 부팅 모드로 부팅하면 시스템가 응답을 중지합니다. 이 문제를 방지하려 면 운영 체제를 설치한 모드와 동일한 부팅 모드로 부팅해야 합니다. 기타 모든 시작 문제는 화면에 표시되는 시스템 메시지를 참고하십시오. 외부 연결 문제 해결 외부 디바이스의 문제를 해결하기 전에 모든 외부 케이블이 시스템의 외부 커넥터에 안전하게 연결되어 있는지 확인하십시오. ● 시스템의 기술 사양과 외부 디바이스를 비교하여 호환성을 확인하십시오. ● 외부 디바이스 기능을 일부 유사한 다른 시스템과 함께 점검하여 디바이스가 정상적으로 작동하고 있는지 확인하십시오.
노트: 이전 운영 체제에서는 USB 3.0이 지원되지 않을 수 있습니다. 4. 시스템 설정에서 USB 3.0이 활성화되어 있는지 확인하십시오. 활성화되어 있으면 이를 비활성화하고 문제가 해결되는지 확인하 십시오. 5. iDRAC Settings Utility(iDRAC 설정 유틸리티)에서 USB Management Port Mode(USB 관리 포트 모드)가 Automatic(자동) 또는 Standard OS Use(표준 OS 사용)로 구성되어 있는지 확인합니다. 6. 문제가 해결되지 않으면, 올바르게 작동하는 키보드 또는 마우스로 교체하십시오. 문제가 해결되지 않으면 7단계로 진행하여 시스템에 연결된 다른 USB 디바이스의 문제를 해결합니다. 문제가 해결되지 않으면 문제 해결을 진행하여 시스템에 연결된 다른 USB 디바이스의 문제를 해결합니다. 7. 연결된 모든 USB 디바이스의 전원을 끄고 시스템에서 연결 해제합니다. 8. 시스템을 재시작합니다. 9.
단계 1. 적절한 진단 테스트를 실행합니다. 자세한 내용은 수행 가능한 진단 테스트에 대한 시스템 진단 프로그램 사용 섹션을 참조하십 시오. 2. 시스템을 재시작하고 NIC 컨트롤러와 관련된 시스템 메시지를 확인합니다. 3. NIC 커넥터에서 해당 표시등을 확인합니다. ● 링크 표시등이 켜지지 않는 경우 연결된 케이블이 해제되었을 수 있습니다. ● 작동 표시등에 빛이 나지 않은 경우 네트워크 드라이버 파일이 손상되었거나 누락되었을 수 있습니다. 필요에 따라 드라이버 를 설치하거나 교체합니다. 자세한 내용은 NIC 설명서를 참조하십시오. ● 상태가 양호한 다른 네트워크 케이블을 시도해 보십시오. ● 문제가 지속되는 경우 스위치 또는 허브의 다른 커넥터를 사용합니다. 4. 적절한 드라이버가 설치되어 있고 프로토콜이 바인딩되는지 확인합니다. 자세한 내용은 NIC 설명서를 참조하십시오. 5.
● 시스템 보드 4. 최소한 하루 이상 시스템을 건조시킵니다. 5. 3단계에서 분리한 구성 요소를 다시 설치합니다(확장 카드 제외). 6. 시스템 커버를 설치합니다. 7. 시스템 및 장착된 주변 기기를 켭니다. 문제가 지속되는 경우 도움말 얻기 섹션을 참조하십시오. 8. 시스템이 올바르게 시작되면 시스템을 종료하고 분리한 모든 확장 카드를 다시 설치합니다. 9. 적절한 진단 테스트를 실행합니다. 자세한 내용은 시스템 진단 프로그램 사용 섹션을 참조하십시오. 다음 단계 검사에 실패하는 경우 도움말 얻기 섹션을 참조하십시오. 관련 참조 도움말 보기 페이지 175 손상된 시스템 문제 해결 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다.
시스템 배터리 문제 해결 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 일부 소프트웨어로 인해 시스템의 시간이 빨라지거나 느려질 수 있습니다. 시스템 설치에 설정된 시간을 제외하고 시스템 의 모든 기능이 정상적으로 작동하는 경우 배터리 결함이 아닌 소프트웨어로 인한 문제일 수 있습니다. 단계 1. 시스템 설정을 통해 시간 및 날짜를 다시 입력합니다. 2. 시스템을 끄고 최소 한 시간 동안 전원 콘센트에서 시스템을 분리한 상태로 둡니다. 3. 시스템을 전원 콘센트에 다시 연결하고 시스템을 켭니다. 4. 시스템 설정을 실행합니다.
결과 노트: 일부 전원 공급 장치에는 정격 용량을 제공하려면 200~240V AC가 필요합니다. 자세한 내용은 www.dell.com/ poweredgemanuals에서 설치 및 서비스 매뉴얼의 시스템 기술 사양 섹션을 참조하십시오. 관련 참조 도움말 보기 페이지 175 전원 공급 장치 문제 단계 1. 느슨한 연결이 없는지 확인합니다. 예를 들어 전원 케이블이 느슨하게 연결되었습니다. 2. PSU(전원 공급 장치) 핸들 또는 LED에서 PSU가 올바르게 작동하고 있다고 나타나는지 확인합니다. PSU 표시등에 대한 자세한 내용은 전원 표시등 코드 섹션을 참조하십시오. 3. 최근에 시스템를 업그레이드한 경우 PSU가 새로운 시스템를 지원하는 충분한 전력이 되는지 확인하십시오. 4. 중복 PSU 구성을 사용하는 경우 두 PSU의 유형과 와트가 동일한지 확인합니다. 더 높은 와트의 전원 공급 장치로 업그레이드해야 할 수 있습니다. 5.
관련 참조 도움말 보기 페이지 175 냉각 팬 문제 해결 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 시스템의 관리 소프트웨어에서 팬 번호를 참조하고 있습니다. 특정 팬에 문제가 발생한 경우, 냉각 팬 어셈블리의 팬 번호 를 메모하여 쉽게 확인하고 교체할 수 있습니다. 1. 안전 지침 섹션에 나와 있는 안전 지침을 따릅니다. 2. 시스템 내부에서 작업하기 전에 섹션의 절차를 따릅니다. 단계 1. 팬 또는 팬의 전원 케이블을 다시 장착합니다. 2. 시스템을 재시작합니다. 다음 단계 1. 시스템 내부 작업을 마친 후에 섹션의 절차를 따릅니다. 2.
6. 시스템 커버를 제거합니다. 7. 메모리 채널이 제대로 설치되었는지 확인합니다. 노트: 시스템 이벤트 로그 또는 시스템 메시지를 참조하여 오류가 있는 메모리의 모듈의 위치를 확인하십시오. 메모리 디바 이스를 다시 설치합니다. 8. 메모리 모듈을 해당 소켓에 다시 장착합니다. 9. 시스템 커버를 설치합니다. 10. 시스템 설치를 시작하고 시스템 메모리 설정을 확인합니다. 문제가 해결되지 않으면 11단계를 진행합니다. 11. 시스템 커버를 제거합니다. 12. 진단 검사 또는 오류 메시지에 특정 메모리 모듈에 결함이 있는 것으로 나타나는 경우 모듈을 상태가 양호한 메모리 모듈로 교체 합니다. 13. 지정되지 않은 결함이 있는 메모리 모듈의 문제를 해결하려면 첫 번째 DIMM 소켓에 있는 메모리 모듈을 유형 및 용량이 같은 모 듈로 교체합니다. 화면에 오류 메시지가 표시되는 경우 설치한 1개 이상의 DIMM 유형에 문제가 있거나, DIMM이 올바르게 설치되지 않았거나, DIMM에 결함이 있을 수 있습니다.
다음 단계 문제가 지속되는 경우 도움말 얻기 섹션을 참조하십시오. 관련 참조 도움말 보기 페이지 175 하드 디스크 드라이브 표시등 패턴 페이지 11 관련 태스크 하드 드라이브 캐리어 분리 페이지 69 하드 드라이브 캐리어 설치 페이지 69 스토리지 컨트롤러 문제 해결 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으 로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 컨트롤러의 문제를 해결하는 경우 운영 체제 및 컨트롤러의 설명서를 참조하십시오. 노트: 미니 PERC 소켓은 핫 플러깅을 지원하지 않습니다. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 적절한 진단 테스트를 실행합니다.
노트: 라이저 슬롯은 핫 플러깅을 지원하지 않습니다. 단계 1. 적절한 진단 테스트를 실행합니다. 시스템 진단 사용 섹션을 참조하십시오. 2. 시스템 및 장착된 주변 기기를 끄고 전기 콘센트에서 시스템을 연결 해제합니다. 3. 시스템 커버를 제거합니다. 4. 각 확장 카드가 해당 커넥터에 단단히 연결되어 있는지 확인합니다. 5. 시스템 커버를 설치합니다. 6. 시스템 및 장착된 주변 기기를 켭니다. 7. 문제가 해결되지 않을 경우 시스템 및 장착된 주변 기기를 끄고 전기 콘센트에서 시스템을 분리합니다. 8. 시스템 커버를 제거합니다. 9. 시스템에 설치된 확장 카드를 모두 분리합니다. 10. 시스템 커버를 설치합니다. 11. 적절한 진단 테스트를 실행합니다. 시스템 진단 사용 섹션을 참조하십시오. 검사에 실패하는 경우 도움말 얻기 섹션을 참조하십시오. 12. 8단계에서 분리한 각 확장 카드에 대해 다음 단계를 수행합니다. a. b. c. d. e.
9 도움말 보기 주제: • • • • Dell EMC에 문의하기 설명서에 대한 사용자 의견 QRL을 사용하여 시스템 정보에 액세스 C6320 QRL(Quick Resource Locator) Dell EMC에 문의하기 Dell EMC는 다양한 온라인 및 전화 기반의 지원 및 서비스 옵션을 제공합니다. 인터넷에 연결되어 있지 않은 경우 구매 송장, 포장 명 세서, 청구서 또는 Dell EMC 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일 부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell EMC에 문의하려면 단계 1. www.dell.com/support/home 페이지로 이동합니다. 2. 페이지 우측 하단에 있는 드롭다운 메뉴에서 국가를 선택합니다. 3. 맞춤화된 지원: a. Enter your Service Tag(서비스 태그 입력) 필드에 시스템 서비스 태그를 입력합니다. b.
단계 1. www.dell.com/qrl 페이지로 이동하여 특정 제품을 탐색하거나 2. 스마트폰 또는 태블릿을 사용하여 시스템 또는 QRL 섹션에서 모델별 QR(Quick Resource) 코드를 스캔합니다.