Owners Manual
Table Of Contents
- Dell PowerEdge FC830 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Cooling shroud retention bar
- System memory
- Processor blank and DIMM blank
- Processors
- PCIe mezzanine card
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Hard drives or SSDs
- Hard-drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard drive or SSD backplane
- Removing a 2.5 inch (x8) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x16) SAS SSD backplane
- Installing a 1.8-inch (x16) SAS SSD backplane
- Storage controller card
- Expander card
- System battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
4. Remove the hard-drive or SSD cage.
NOTE: You must remove the hard-drive or SSD cage to replace a faulty hard-drive or SSD cage or service other
components inside the system.
Steps
1. Align the slots on the sides of the hard-drive or SSD cage with the standoffs on the chassis.
2. Lower the hard-drive or SSD cage into the chassis until the slots on the hard-drive or SSD cage engage with the standoffs
on the chassis.
3. Slide the hard-drive or SSD cage into the chassis until it clicks into position.
4. Install the two screws to secure the hard-drive or SSD cage to the chassis.
Figure 54. Installing the hard-drive or SSD cage
1.
standoff (4) 2. hard-drive or SSD cage
3. screw (2) 4. screw hole (2)
Next steps
1. Install the hard-drive or SSD backplane.
2. Install the harddrive or SSD.
3. Follow the procedure listed in the After working inside your system section.Follow the procedure listed in the After working
inside your system section.
Related references
Safety instructions on page 48
Related tasks
Before working inside your system on page 48
Removing the hard-drive or SSD cage on page 106
After working inside your system on page 49
108
Installing and removing sled components