Owners Manual
Table Of Contents
- Dell PowerEdge FC830 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Cooling shroud retention bar
- System memory
- Processor blank and DIMM blank
- Processors
- PCIe mezzanine card
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Hard drives or SSDs
- Hard-drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard drive or SSD backplane
- Removing a 2.5 inch (x8) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x16) SAS SSD backplane
- Installing a 1.8-inch (x16) SAS SSD backplane
- Storage controller card
- Expander card
- System battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
PCIe mezzanine card specification
The PowerEdge FC830 system supports two PCIe x16 Gen 3 slots mezzanine cards.
Video specifications
The PowerEdge FC830 system supports Matrox G200 VGA controller integrated with iDRAC and 2 GB video memory is shared
with iDRAC application memory.
Environmental specifications
NOTE: For additional information about environmental measurements for specific system configurations, see Dell.com/
environmental_datasheets.
Table 9. Temperature specifications
Temperature Specifications
Storage –40°C to 65°C (–40°F to 149°F)
Continuous operation (for altitude less than 950
m or 3117 ft)
10°C to 35°C (50°F to 95°F) with no direct sunlight on the equipment
Fresh air For information about fresh air, see the Expanded Operating Temperature
section.
Maximum temperature gradient (operating and
storage)
20°C/h (36°F/h)
Table 10. Relative humidity specifications
Relative humidity Specifications
Storage 5% to 95% RH with 33°C (91°F) maximum dew point. Atmosphere must be
non-condensing at all times.
Operating 10% to 80% RH with 29°C (84.2°F) maximum dew point.
Table 11. Maximum vibration specifications
Maximum vibration Specifications
Operating 0.26 G
rms
at 5 Hz to 350 Hz (all operation orientations)
Storage 1.88 G
rms
at 10 Hz to 500 Hz for 15 minutes (all six sides tested)
Table 12. Maximum shock pulse specifications
Maximum shock pulse Specifications
Operating Six consecutively executed shock pulses in the positive and negative x, y,
and z axes of 40 G for up to 2.3 ms.
Storage Six consecutively executed shock pulses in the positive and negative x, y,
and z axes (one pulse on each side of the system) of 71 G for up to 2 ms.
Table 13. Maximum altitude specifications
Maximum altitude Specifications
Operating 3048 m (10,000 ft)
Storage 12,000 m (39,370 ft)
Technical specifications 13