Owners Manual
Table Of Contents
- Dell PowerEdge FC830 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Cooling shroud retention bar
- System memory
- Processor blank and DIMM blank
- Processors
- PCIe mezzanine card
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Hard drives or SSDs
- Hard-drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard drive or SSD backplane
- Removing a 2.5 inch (x8) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x16) SAS SSD backplane
- Installing a 1.8-inch (x16) SAS SSD backplane
- Storage controller card
- Expander card
- System battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
8. Reinstall the sled after an hour.
9. Follow the procedure listed in the After working inside your system section.
10. Enter System Setup and if the time and date are still incorrect, see Getting help section.
Related references
Safety instructions on page 48
Related tasks
Before working inside your system on page 48
Hard drives or SSDs on page 95
Hard-drive or SSD cage on page 106
Hard drive or SSD backplane on page 109
Removing memory modules on page 64
After working inside your system on page 49
System board
A system board (also known as the motherboard) is the main printed circuit board found in computers. The system board allows
communication between many of the crucial electronic components of the computer, such as the central processing unit (CPU)
and memory, and also provides connectors for other peripherals. Unlike a backplane, a system board contains significant number
subsystems such as the processor expansion cards, and other components.
Removing the system board
Prerequisites
CAUTION:
Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that came with the product.
NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell
certified service technicians.
NOTE: You must remove the system board to replace a faulty system board.
1. Follow the safety guidelines listed in the Safety instructions section.
2. Follow the procedure listed in the Before working inside your system section.
3. Keep the 5 mm and 6 mm Hex nut drivers, #2 Phillips screwdriver, and #2 Phillips round screwdriver ready.
4. Remove the following:
a. processor(s) and heat sink(s)
b. memory modules
c. cooling shroud
d. hard drives or SSDs
e. hard-drive backplane or SSD backplane
f. hard-drive cage or SSD cage
g. storage controller card
h. expander card
i. PCIe mezzanine cards
j. IDSDM card or rSPI card
130
Installing and removing sled components