戴尔 PowerEdge FX2 和 FX2s 机柜 用户手册 管制型号: E24S 管制类型: E24S001 June 2020 Rev.
注意、小心和警告 注: “注意”表示帮助您更好地使用该产品的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告: “警告”表示可能会导致财产损失、人身伤害甚至死亡。 © 2014 – 2020 Dell Inc. 或其子公司。保留所有权利。Dell、EMC 和其他商标均是 Dell Inc.
目录 章 1: 关于 Dell PowerEdge FX2/FX2s.................................................................................................6 说明文件中使用的术语........................................................................................................................................................6 底座插槽编号方式................................................................................................................................................................ 7 前面板功能部件和指示灯 — PowerEdge FX2/FX2s............
拆装计算机内部组件之后.................................................................................................................................................. 31 建议工具............................................................................................................................................................................... 31 系统护盖....................................................................................................................................................................
电源插入器板................................................................................................................................................................ 69 控制面板...............................................................................................................................................................................70 卸下控制面板..........................................................................................................................................................
1 关于 Dell PowerEdge FX2/FX2s Dell PowerEdge FX2/FX2s 采用 2U 机柜,可支持多达四个半宽计算底座,最多支持八个四分之一宽计算底座,最多支持两个全宽计 算底座,或计算底座类型混合。PowerEdge FX2s 机柜还支持映射到计算底座的半宽存储底座。 注: 有关 PowerEdge FX2s 机柜中存储底座映射到计算底座的映射配置信息,请参阅位于 Dell.
表.
图 4: 底座插槽编号方式 — 六托架机箱 图 5: 底座插槽编号方式 — 三托架机箱 前面板功能部件和指示灯 — PowerEdge FX2/FX2s 图 6: 前面板功能部件和指示灯 — PowerEdge FX2/FX2s 表.
表. 2: 前面板功能部件和指示灯 — PowerEdge FX2/FX2s (续) 项目 指示灯、按钮或连接器 图标 说明 ● 两个全宽计算底座,或 ● 四个四分之一宽计算底座和两个半宽计算底座,或 ● 一个全宽计算底座和多达两个半宽计算底座 注: PowerEdge FX2s 支持计算底座和存储底座的组 合。有关映射存储底座到 PowerEdge FX2s 中计算底 座的详情,请参阅位于 Dell.com/ poweredgemanuals 的 Dell PowerEdge FD332 Owner's Manual(用户手册) 。 6 视频连接器 可用于将显示器连接到系统。 7 USB 连接器 可用于将键盘或鼠标连接到系统。 诊断指示灯 系统前面板上的诊断指示灯在系统启动时显示错误状态。 注: 当系统关闭时诊断指示灯不亮。要启动系统,将系统连接至正常工作的电源并按下电源按钮。 下表列出了系统状态和关联诊断指示灯的可能的纠正措施。 表.
表.
图 8: 背面板功能部件和指示灯 — PowerEdge FX2 表.
图 9: PSU 指示灯 1. AC PSU 状态指示灯/手柄 注: 2000 W PSU 电源电缆连接器与上图中所示的连接器不同。 PSU 指示灯提供以下信息: 表.
图 11: I/O 模块指示灯(交换机模块) 1. 电源指示灯 2. 状态指示灯 指示灯提供以下信息: 电源指示灯显示 说明 方式 绿色 I/O 模块运行正常。 Off(关闭) I/O 模块的电源已关闭。 状态指示灯显示 说明 方式 蓝色 I/O 模块运行正常。 呈蓝色闪烁 CMC 正在识别 I/O 模块。 呈琥珀色闪烁 I/O 模块处于故障状态。 Off(关闭) I/O 模块的电源已关闭,或者正在引导。 有关更多信息,请参阅位于 Dell.com/poweredgemanuals 的 I/O 模块说明文件。 CMC 模块 图 12: CMC 模块 1. 用于本地配置的 DB-9 串行连接器 3. 链路指示灯 5. 以太网连接器 STK/Gb2(堆叠) 2. 以太网连接器 Gb1 4. 活动指示灯 6.
Indicator(指示 说明 灯) 琥珀色 机箱处于故障状态。 CMC 功能 CMC 提供如下多种系统管理功能: ● 机柜级别的电源和温度实时自动管理: ○ 监控系统电源要求。 ○ 报告实时功耗,包括用时间戳记录的最高点和最低点。 ○ 支持对可选的机柜最大电源上限进行设置,一旦超过该限制就将触发警报或采取操作(例如对计算底座节流和/或防止接通新 计算底座的电源),使机柜电源保持在规定的最大电源上限之内。 ○ 监控冷却风扇,同时根据实际环境温度和内部温度测量值自动控制冷却风扇。 ○ 提供全面的机柜资源清册和状态或错误报告。 ● 集中配置以下内容: ○ 机柜的网络和安全设置。 ○ 电源冗余和电源上限设置。 注: 关闭模块化机柜时,建议修改模块化机柜冗余策略。 ○ ○ ○ ○ I/O 模块和 iDRAC 网络设置。 计算底座上的第一引导设备。 检查 I/O 模块、PCIe 插槽和底座的 I/O 路径一致性,并在必要时禁用组件,以保护系统硬件。 用户访问安全。 CMC 模块是热插拔型。在卸下 CMC 模块期间: ● 不能打开新安装的计算底座 ● 不能远程访问现有计算底座 ● 机箱冷却风扇以最大速度运行以热保
图 13: CMC 菊花链式连接 1. 管理网络 2.
图 14: 冷却风扇指示灯 1. 状态指示灯 配置向导 CMC 已预先配置为使用静态 IP 地址。要使用动态主机配置协议 (DHCP),请执行以下操作: 1. 访问 Chassis Management Controller (CMC)。 2. 单击 Network(网络)。 3. 单击 IPv4 或 IPv6。 4. 选择 启用 DHCP。 有关更多信息,请参阅 Dell.com/esmmanuals 上的 Dell PowerEdge FX2/FX2s CMC 用户指南。 系统消息 CMC Web 界面上显示系统消息,通知您机柜和其中的底座可能出现的相关问题。有关这些错误消息的更多信息(包括可能的原因和 解决方案),请参阅 Dell Event and Error Messages Reference Guide(Dell 事件和错误消息参考指南),网址:Dell.com/ openmanagemanuals → OpenManage 软件。 说明文件列表 此说明文件列表提供了您可以参阅的有关设置和管理系统的说明文件的信息。 表. 6: 说明文件列表 要... 请参阅...
表. 6: 说明文件列表 (续) 要... 请参阅... 安装、配置和使用 Chassis Management Controller (CMC) Dell.com/esmmanuals 上 的 Dell PowerEdge FX2/FX2s CMC User’s Guide(Dell PowerEdge FX2/FX2s CMC 用户指南) 了解有关 RACADM 子命令和支持的 RACADM 界面 RACADM Command Line Reference Guide for iDRAC and CMC (适用于 iDRAC 和 CMC 的 RACADM 命令行参考指南),位于 Dell.com/esmmanuals 启动、启用和禁用 Lifecycle Controller,了解这些功能,Lifecycle Dell Lifecycle Controller User’s Guide(Dell 生命周期控制器用户 Controller 的使用和故障排除 指南)网 址 Dell.
2.
2 初始系统配置 主题: 开始之前 设置 PowerEdge FX2/FX2s 登录 CMC • • • 开始之前 小心: 机柜电源设备必须连接到 PDU 或电源插座。电源设备需要 100 V 至 120 V 或 200 V 至 240 V 的电源。您只能选择一种交 流电源输入,因为系统不会同时在这两个范围内运行。 ● 如果适用,还可更新计算底座上的所有 PCIe 卡固件和 iDRAC 固件。 ● 从 Dell.com/support 下载最新版 CMC 固件。此外,请确保您有随系统提供的 Dell Systems Management Tools and Documentation(Dell 系统管理工具和说明文件)DVD。 ● 如果网络使用静态寻址,则需要提供 IP 地址、子网掩码和网关来配置 CMC 与机柜中的其它底座。 设置 PowerEdge FX2/FX2s 步骤 1. 打开机柜和底座的包装,并确认每项物品。 有关更多信息,请参阅 Dell PowerEdge FX2 系统入门指南和机架安装指南,网址:Dell.
12. 通过使用 Web 浏览器连接到各 iDRAC 并键入 iDRAC 的最终配置。 默认用户名是 root,默认密码是 calvin。 13. 开启计算底座电源并安装操作系统。 后续步骤 要查看逐步说明以取出并安装机柜,请扫描下面的快速资源代码。有关快速资源定位器的更多信息,请参阅通过使用 QRL 访问系统 信息 页面上的 17。 图 15: 安装机柜的快速资源定位器 登录 CMC 可以在得到 IP 地址之前或之后执行机箱管理控制器 (CMC) 的初始网络配置。 您可以作为 CMC 本地用户、Microsoft Active Directory 用户或 LDAP 用户登录 CMC。也可以使用单一登录或智能卡登录。 有关管理系统和配置设置的更多信息,请参阅 Dell.
3 PowerEdge FX2/FX2s 映射配置 本节提供计算底座连接到机柜的 I/O 模块、PCIe 插槽和机箱管理控制器 (CMC) 的以下信息: ● 主板 LAN 网络和计算底座至 I/O 模块端口映射配置 ● 扩充总线和计算底座至 PCIe 扩展槽映射配置 ● 内部管理网络 注: 计算底座的 I/O 模块端口映射和 PCIe 插槽映射是预先配置的。 主题: • • • • • 主板 LAN 网络 I/O 模块和 PCIe 夹层卡配置原则 配置 I/O 模块的网络设置 扩展总线 内部管理网络 主板 LAN 网络 主板 LAN (LOM) 网络是指通过安装在 PowerEdge 和 FX2/FX2s 机柜后面的 I/O 模块提供至计算底座的以太网连接。 LOM 网络为每个半宽底座提供四个连接,为每个四分之一宽计算底座提供两条连接,为每个全宽计算底座提供八条连接,适用于最 多 16 个通路。可用的最大外部连接为 16 个 RJ-45 以太网端口。 受支持的 I/O 模块 该机柜支持多达两个交换机或直通模块。以太网直通模块的最大宽度为八通道。 机柜支持以下 I/O 模块: ● ● ● ● ● De
图 16: I/O 模块端口映射 - 配有双端口 NDC 的半宽计算底座 配有双端口网络子卡 (NDC) 的半宽计算底座映射至各个 I/O 模块上的单个端口。下表列出了计算底座及其映射到的端口。 表. 7: I/O 模块端口映射 -半宽计算底座( 配有双端口 NDC) 计算底座 I/O 模块 A1(顶部) I/O 模块 A2(底部) 1 1 1 2 3 3 3 5 5 4 7 7 图 17: I/O 模块端口映射 - 配有双端口 NDC/网络输出的半宽计算底座 配置四端口 NDC 的半宽计算底座映射至各个 I/O 模块上的两个端口。 带有四个计算节点的半宽计算底座配有四端口网络输出,它映射至各个 I/O 模块上的两个端口。从计算底座中的节点到机柜中的 I/O 模块的网络通信通过嵌入在计算底座系统板上的网络交换机路由。有关更多信息,请参阅 Dell.com/poweredgemanuals 上的 Dell PowerEdge FM120x4 Owner's Manual(《Dell PowerEdge FM120x4 用户手册》)。 下表列出了计算底座及其映射到的端口。 表.
I/O 模块端口映射 - 八托架机箱 在八托架机箱中,最多可支持八个四分之一宽计算底座,将计算底座映射至各个 I/O 模块上的单个端口。 图 18: I/O 模块端口映射 - 八托架机箱 下表列出了计算底座及其映射到的端口。 表.
图 19: I/O 模块端口映射 - 6 托架机箱 下表列出了计算底座及其映射到的端口。 表. 10: 六托架机六箱中 I/O 模块端口映射 计算底座 I/O 模块 A1(顶部) I/O 模块 A2(底部) 1a 1 1 1b 2 2 1c 3 3 1d 4 4 3 5、6(对于带有四端口 NDC 的半宽计算底座) 5、6(对于带有四端口 NDC 的半宽计算底座) 5(对于带有四端口 NDC 的半宽计算底座) 5(对于带有四端口 NDC 的半宽计算底座) 7、8(对于带有四端口 NDC 的半宽计算底座) 7、8(对于带有四端口 NDC 的半宽计算底座) 7(对于带有四端口 NDC 的半宽计算底座) 7(对于带有四端口 NDC 的半宽计算底座) 4 I/O 模块端口映射 - 双托架机箱 在双托架机箱配置中,最多支持两个全宽计算底座,一个计算底座映射至各个 I/O 模块的四个端口。 图 20: I/O 模块端口映射 - 全宽计算底座 下表列出了计算底座及其映射到的端口。 表.
表. 11: I/O 模块端口映射 - 全宽计算底座 (续) 计算底座 I/O 模块 A1(顶部) I/O 模块 A2(底部) 3 5、6、7、8 5、6、7、8 I/O 模块端口映射 - 三机架机箱 三托架机箱支持一个全宽计算底座和最多两个半宽计算底座的组合。 在 3 托架的机箱中,一个全宽计算底座映射至各个 I/O 模块的四个端口。配置四端口 NDC 的半宽计算底座映射至各个 I/O 模块上的 两个端口。 注: 配有双端口 NDC 的半宽计算底座映射至各个 I/O 模块上的单个端口。 注: 在三个托架的 PowerEdge FX2s 配置中,支持映射到全宽计算底座的存储底座,仅计算底座映射到 I/O 模块端口。如果安装 了存储底座,I/O 模块上映射到这些插槽的相应端口不处于活动状态。 图 21: I/O 模块端口映射 - 三机架机箱 下表列出了计算底座及其映射到的端口。 表.
配置 I/O 模块的网络设置 您可以指定用于管理为 I/O 模块的接口的网络设置。 配置 I/O 模块的网络设置之前,请确保 I/O 模块已通电。 要配置网络设置,您必须具有 LOM 网络的管理员权限,以配置组 A 中的 I/O 模块。 可以使用以下工具配置网络设置: ● CMC Web 界面 ● RACADM 有关配置网络设置的更多信息,请参阅 Dell.
图 23: 计算底座至 PCIe 插槽映射 —八托架机箱 图 24: 计算底座至 PCIe 插槽映射 —六托架机箱 图 25: 计算底座至 PCIe 插槽映射 — 双托架机箱 PowerEdge FX2/FX2s 映射配置 27
图 26: 计算底座至 PCIe 插槽映射 — 三托架机箱 映射到存储底座的计算底座的 PCIe 插槽映射 在支持存储底座映射到计算底座的 PowerEdge FX2s 机柜配置中,PCIe 插槽仅映射到计算底座。在机柜中安装存储底座后,映射到 这些托架的 PCIe 插槽自动重新分配给机柜上部托架中安装的计算底座。PCIe 插槽重新分配功能使您可以将 PCIe 插槽从下部托架中 的计算底座重新分配从上部托架中的计算底座。该 PCIe 插槽重新分配功能适用于带有或不带有存储底座的机柜配置。您可以使用 CMC Web 界面、CMC WSMAN 或 RACADM 启用或禁用 PCIe 重新分配选项。有关更多信息,请参阅 PowerEdge FX2/FX2s CMC User’s Guide(PowerEdge FX2/FX2s CMC 用户指南)和 Dell Chassis Management Controller for PowerEdge FX2/FX2s RACADM Command Line Reference Guide( Dell Chassis Management Controller for
图 28: 映射到存储底座的计算底座的 PCIe 插槽映射 - 四托架机箱(带单个计算底座) 图 29: 映射到存储底座的计算底座的 PCIe 插槽映射 — 三托架机箱 图 30: 映射到存储底座的计算底座的 PCIe 插槽映射 — 六托架机箱 管理 PCIe 插槽 您可以查看系统中单个和所有 PCIe 插槽的状态。有关使用 CMC Web 界面管理 PCIe 插槽的详细信息,请参阅 Dell PowerEdge FX2/ FX2s CMC User’s Guide(Dell PowerEdge FX2/FX2s CMC 用户指南),网址:Dell.
4 安装和卸下 PowerEdge FX2/FX2s 机柜组件 本节提供有关安装和拆卸机柜组件的信息。有关卸下和安装底座组件的信息,请参阅位于 Dell.
安全说明 注: 每当您需要抬起系统时,请让他人协助您。为避免伤害,请勿尝试一个人抬起系统。 注: 系统处于运行状态时打开或卸下系统护盖会使您有触电的风险。 注: 当系统开机时,请务必小心地卸下或安装组件,以避免触电风险。 小心: 请勿在卸下系统护盖时运行系统超过三分钟。 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 注: 为了确保正常操作和冷却,必须始终在系统中的所有托架上装入底座或挡片。 注: 建议您从机箱中卸下底座和电源设备以减轻重量,然后在机架中安装机柜。 拆装计算机内部组件之前 步骤 1. 使用 CMC、iDRAC 或计算底座电源按钮关闭计算底座。 存储底座映射的计算底座关闭时存储底座会关闭。 2. 关闭机柜和连接的外围设备,并断开机柜与电源插座的连接。 拆装计算机内部组件之后 步骤 1.
系统护盖 卸下系统护盖 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 为了确保正常操作和冷却,在卸下后三分钟内装回系统护盖。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 步骤 1. 将护盖锁逆时针转至解除锁定位置。 2. 朝护盖锁方向按下系统两侧的释放闩锁。 3. 将护盖朝系统前端滑动,然后将护盖提离系统。 图 31: 卸下和安装系统护盖 a. 释放闩锁(2 个) b. 系统护盖 c.
安装系统护盖 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下系统护盖。 注: 您必须卸下系统护盖才能维修系统内部的组件。 步骤 1. 将护盖的底边(正对护盖锁)插入系统的插槽中。 2. 将护盖向下放置到系统箱上。 3. 将系统护盖向系统后部滑动,直到系统护盖与系统表面平齐。 4. 将护盖锁沿顺时针方向旋转至锁定位置。 后续步骤 请按照拆装计算机内部组件之后 页面上的 31 中的步骤进行操作。 相关信息 卸下系统护盖 页面上的 32 底座 小心: 为了确保正常操作和冷却,必须在卸下底座或挡片两分钟内,为系统中的所有托架装回底座或挡片。 注: 确保您已从 Dell.
图 32: 卸下和安装计算底座 1. 机柜 3. 计算底座手柄 2. 计算底座 4. 底座手柄上的释放按钮 后续步骤 安装计算底座或底座档片。 相关任务 安装计算底座 页面上的 34 安装计算底座 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 确保已阅读安全说明 页面上的 31。 步骤 1. 如果要安装新计算底座,请从 I/O 连接器中取下塑料护盖,并妥善保存护盖以供将来使用。 2. 将底座手柄上的释放按钮按至打开位置。 3. 将计算底座与机柜中的托架对齐。 4. 将底座滑入机柜,直至底座连接器牢固的扣住中间板连接器。 底座滑入机柜时,将底座手柄转向机柜。 5.
后续步骤 开启计算底座。 相关信息 卸下计算底座 页面上的 33 卸下存储底座 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 小心: 在存储底座通电时从机柜中卸下存储底座将导致数据丢失。 小心: 为防止损坏存储底座锁,使用 2 号梅花槽螺丝刀将底座锁转到锁定或解锁位置。 1. 确保已阅读安全说明 页面上的 31。 2. 使用 CMC、iDRAC 或底座电源按钮关闭存储底座映射的计算底座。 3. 准备好 2 号梅花槽螺丝刀。 步骤 1. 使用 2 号梅花槽螺丝刀时,将底座前面板上的存储底座锁旋至解锁位置。 小心: 如果永久卸下底座,则安装底座挡片。长时间在未安装底座挡片的情况下操作机柜会导致机柜过热。 2. 将底座释放闩锁向上提起 90 度,然后握住其闩锁,将底座拉出机柜。 小心: 为保护输入/输出连接器插针,任何时候从机柜中卸下底座后,请立即安装输入/输出连接器护盖。 3.
图 33: 卸下存储底座 a. 底座锁(2 个) b. 存储底座上的虚线 c. 底座释放闩锁(2 个) 图 34: 卸下和安装 I/O 连接器护盖 a. 存储底座 b.
安装存储底座 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 小心: 为了防止损坏 I/O 连接器,请勿触摸连接器或连接器插针。 小心: 为防止损坏底座锁,使用 2 号梅花槽螺丝刀将底座锁旋转至锁定或解锁位置。 注: 从左侧(插槽 3)开始,将存储底座安装在 PowerEdge FX2s 机柜的底部插槽中。在四托架机箱中,您还可以在机柜的右上 插槽(插槽 2)中安装存储底座。有关底座插槽编号的详细信息,请参阅 Dell.com/poweredgemanuals 上的 Dell PowerEdge FX2 and FX2s 机柜用户手册。 注: 如果您的存储底座出厂时已预安装在机柜中,建议您在将机柜安装在机架中之前卸下底座,以减少机箱重量。 注: 如果您将存储底座安装在已接通电源的机柜中,您无需关闭机柜来安装存储底座。只有存储底座映射的计算底座才需要关 闭。 1. 请务必阅读安全说明。 2.
图 35: 安装存储底座 a. 存储底座上的虚线 b.
图 36: 系统内部组件 — PowerEdge FX2s 1. 3. 5. 7. 中间板 电源总线条 电源设备(2 个) CMC 模块 2. 风扇(8 个) 4. 电源插入器板 6.
卸下 CMC 模块 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 您必须卸下 CMC 才能更换故障模块或维修系统内部的其他组件。 注: CMC 模块是热插拔型。 确保已阅读安全说明 页面上的 31。 步骤 1. 断开连接至 CMC 模块的电缆。 2. 按下释放闩锁并将 CMC 模块滑出机柜。 图 37: 卸下和安装 CMC 模块 a. CMC 模块 b. CMC 模块手柄 c. 释放闩锁 后续步骤 安装 CMC 模块。 相关任务 安装 CMC 模块 页面上的 40 安装 CMC 模块 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 1. 确保已阅读安全说明 页面上的 31。 2.
步骤 1. 从包装中取出 CMC 模块,做好安装前的准备工作。 2. 将 CMC 模块滑入机柜中,直至 CMC 模块连接器扣住中间板上的插针。 3. 将电缆连接至 CMC 模块。 相关信息 卸下 CMC 模块 页面上的 40 CMC 模块 SD 卡 CMC 模块上的 SD 卡插槽支持可选的 WWN/MAC 功能,该功能允许底座使用基于插槽的 WWN/MAC,从而简化了底座的安装和更 换。 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 1. 确保已阅读安全说明 页面上的 31。 2. 卸下 CMC 模块。 注: 检查写保护闩锁是否位于解除锁定位置。 步骤 找到 CMC 模块底部的 SD 卡插槽,然后将该卡的插针端插入到插槽中,保持卡标签面朝上。 图 38: 拆下和安装 CMC 模块 SD 卡 a. SD 卡 b.
I/O 模块 您的系统最多支持两个热插拔 I/O 模块,用于提供外部网络连接。 卸下 I/O 模块 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 您必须卸下 I/O 模块才能更换出现故障的模块,或者维修系统的其他组件。 注: I/O 模块是热插拔型。 确保已阅读安全说明 页面上的 31。 步骤 1. 断开连接至 I/O 模块的电缆。 2. 按下释放闩锁并将 I/O 模块滑出机柜。 图 39: 卸下和安装 I/O 模块 a. I/O 模块 b. I/O 模块手柄 c.
步骤 1. 从包装中取出 I/O 模块,做好安装前的准备工作。 有关说明,请参阅与 I / O 模块随附的说明文件。 2. 将 I/O 模块滑入机柜,直至扣住中间板上的连接器,并且释放闩锁卡入到位。 3.
相关任务 安装 PCIe 模块 页面上的 44 安装 PCIe 模块 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 小心: PCIe 模块是可热插拔组件。PCIe 模块中的每个 PCIe 插槽被分配给一个计算底座。在 PCIe 模块所分配的计算底座开启 时卸下或添加 PCIe 模块会导致错误状况。 1. 确保已阅读安全说明 页面上的 31。 2. 卸下 PCIe 模块。 注: 您必须卸下 PCIe 模块才能更换出现故障的模块,在 PCIe 模块中装回或更换扩展卡,或维护系统内的其他组件。 步骤 1. 卸下 PCIe 模块连接器护盖。 2. 安装扩展卡或填充挡片。 3.
表. 14: 扩展卡工作电源状态 机箱状态 计算底座状态 扩展卡状态 Off(关闭) Off(关闭) Off(关闭) 待机 Off(关闭) Off(关闭) On(打开) Off(关闭) Off(关闭) On(打开) On(打开) On(打开) 下表提供了有关扩展卡(在 PCIe 插槽中更换时)的操作电源状态的信息。 表.
注: 您必须在空置的扩展卡槽中安装一个填充挡片以使系统符合联邦通讯委员会 (FCC) 认证系统。这些挡片也能将灰尘挡在 系统以外,同时有助于系统内的正确通风散热。散热器是维持正常散热状态所必不可少的。 图 41: 卸下和安装扩展卡 a. 扩展卡 b. 释放闩锁 后续步骤 1. 安装 PCIe 模块。 2. 打开该扩展卡映射到的计算底座。 相关任务 卸下 PCIe 模块 页面上的 43 安装 PCIe 模块 页面上的 44 安装扩展卡 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 1. 2. 3. 4. 5. 确保您已阅读 安全说明 页面上的 31。 关闭该扩展卡分配到的计算底座。 卸下 PCIe 模块。 打开扩展卡释放闩锁。 卸下填充挡板。 步骤 1. 打开扩展卡的包装并准备安装。 有关说明,请参阅随插卡提供的说明文件。 2.
3. 将卡式边缘连接器稳固地插入扩展卡连接器,直至扩展卡完全就位。 4. 关闭扩展卡释放闩锁。 后续步骤 1. 安装 PCIe 模块。 2.
图 42: 卸下和安装 PSU 1. 释放闩锁 3. PSU 5. PSU 手柄 2. PSU 电缆连接器 4. 连接器 后续步骤 1. 安装 PSU。 2. 将电源电缆连接至 PSU 并将电缆插入电源插座。 相关任务 安装电源设备 页面上的 48 安装电源设备 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 在安装、热插拔或热添加新的电源设备 (PSU) 时,请等待几秒钟,以便系统识别 PSU 和确定其状态。PSU 状态指示灯变为 绿色以表示该 PSU 正常工作。 1. 确保已阅读安全说明 页面上的 31。 2. 卸下 PSU。 注: 您必须卸下电源设备来更换出现故障的电源设备、维修系统的其他组件,或在机架中安装机柜时减少机箱重量。 步骤 1. 将 PSU 滑入机箱直至其完全固定住,并将释放闩锁卡入到位。 小心: 连接电源电缆时,请使用紧固带固定电缆。 2.
冷却风扇 您的系统支持八个可热插拔冷却风扇,用于冷却系统中的 I/O 组件。 要为系统中的 PCIe 组件增加冷却,可以在 CMC Web 界面中更改风扇偏移选项。 有关风扇偏移属性的更多信息,请参阅 CMC 联机帮助中的高级风扇配置。 注: 如果要卸下风扇,请立即用另一个风扇代替该风扇。在未安装风扇的情况下长时间运行系统会导致机柜过热。 注: 如果某个风扇出现故障,系统的管理软件会引用该风扇编号,使您可以通过观察冷却风扇托架上的风扇编号来轻松识别和更 换相应的风扇。如果任何风扇发生故障,该风扇的 LED 会亮起。 注: 您的系统中配备的冷却风扇有两种尺寸规格:80 毫米和 60 毫米宽。 卸下冷却风扇 前提条件 注: 系统处于运行状态时打开或卸下系统护盖会使您有触电的风险。在卸下或安装冷却风扇时要额外小心。 注: 冷却风扇在关机后还将继续旋转一段时间。请等候风扇停止转动后再将其从系统中卸除。 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵
图 43: 卸下和安装冷却风扇 a. 冷却风扇固定框架 b. 风扇释放卡舌 c. 冷却风扇(8 个) 后续步骤 安装冷却风扇。 相关任务 安装冷却风扇 页面上的 50 卸下系统护盖 页面上的 32 安装冷却风扇 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 1. 确保已阅读安全说明 页面上的 31。 2. 卸下冷却风扇。 注: 您必须卸下冷却风扇才能替换有故障的风扇和维修息系统中的其他组件。 步骤 1. 将冷却风扇基座上的插头与 PCIe 交换机板/风扇接口板上的连接器对齐。 2. 将冷却风扇滑入机箱,直至插头与 PCIe 交换机板/风扇接口板上的连接器啮合。 后续步骤 1. 安装系统护盖。 2.
相关任务 安装系统护盖 页面上的 33 相关信息 卸下冷却风扇 页面上的 49 冷却风扇固定框架 卸下冷却风扇固定框架 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 注: 您必须卸下冷却固定框架才能维修系统内部的其他组件。 1. 2. 3. 4. 确保已阅读安全说明 页面上的 31。 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 卸下系统护盖。 卸下冷却风扇。 步骤 1. 拧松将冷却风扇固定框架固定至系统的六颗螺钉。 2. 从系统中取出冷却风扇固定框架。 图 44: 卸下和安装冷却风扇固定框架 a. 螺钉(6 颗) b.
图 45: 冷却风扇固定框架顶部视图 a. 螺钉位置(6 个) 后续步骤 安装冷却风扇固定框架。 相关任务 安装冷却风扇固定框架 页面上的 52 卸下系统护盖 页面上的 32 卸下冷却风扇 页面上的 49 安装冷却风扇固定框架 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下冷却风扇固定框架。 注: 您必须卸下冷却固定框架才能维修系统内部的其他组件。 步骤 1. 将冷却风扇固定框架向下放入系统中。 注: 在将冷却风扇固定框架放入系统时,确保没有电缆造成妨碍。 2. 拧紧螺钉,直至冷却风扇固定框架与系统咬合。 后续步骤 1. 安装冷却风扇。 2. 安装系统护盖。 3.
相关信息 卸下冷却风扇固定框架 页面上的 51 PCIe 交换机板 PowerEdge FX2s 机柜支持 PCIe 交换机板。以下步骤适用于 PowerEdge FX2s 机柜。 卸下 PCIe 交换机板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤必须仅限 Dell 认证的维修技术人员执行。 注: 您必须卸下 PCIe 交换机板才能更换出现故障的交换机板或维修系统内的其他组件。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下以下组件: ● 系统护盖 ● 冷却风扇 ● 冷却风扇固定框架 ● PCIe 模块 步骤 1. 拧松将 PCIe 交换机板固定至系统的两个弹簧螺钉。 2. 按下释放闩锁。 两个拉杆被释放。 3.
3. 槽口(4 个) 4. 弹簧螺钉(2 颗) 后续步骤 装回 PCIe 交换机板 相关任务 安装 PCIe 交换机板 页面上的 54 卸下系统护盖 页面上的 32 卸下冷却风扇 页面上的 49 卸下冷却风扇固定框架 页面上的 51 卸下 PCIe 模块 页面上的 43 安装 PCIe 交换机板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下 PCIe 开关板。 注: 您必须卸下 PCIe 交换机板才能更换出现故障的交换机板或维修系统内的其他组件。 步骤 1. 将 PCIe 交换机板向下放入系统中。 注: 确保 PCIe 交换机板底部的卡舌扣住系统上的槽口。 2.
风扇接口板 PowerEdge FX2 机柜支持风扇接口板。以下步骤适用于 FX2 机柜。 卸下风扇接口板 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 注: 您必须卸下风扇接口板才能更换有故障的风扇和维修息系统中的其他组件。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下以下组件: ● 系统护盖 ● 冷却风扇 ● 冷却风扇固定框架 步骤 1. 拧松将风扇接口板固定至系统的两颗弹簧螺钉。 2. 握住风扇接口板的把手,将风扇接口板从系统中提出。 图 47: 卸下和安装风扇接口板 a. 把手(2 个) b. 槽口(4 个) c.
相关任务 安装风扇接口板 页面上的 56 卸下系统护盖 页面上的 32 卸下冷却风扇 页面上的 49 卸下冷却风扇固定框架 页面上的 51 安装风扇接口板 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 安装风扇接口板。 注: 您必须卸下风扇接口板才能更换有故障的风扇和维修息系统中的其他组件。 步骤 1. 将风扇接口板放入系统中。 注: 确保风扇接口板背面的卡舌扣住系统上的槽口。 2. 向中间板滑动风扇接口板,直至连接器牢固地扣住中间板上的插针。 3. 拧紧两颗弹簧螺钉,将风扇接口板固定至系统。 后续步骤 1. 安装以下组件: ● 冷却风扇固定框架 ● 冷却风扇 ● 系统护盖 2.
图 48: 插入器模块顶部视图 1. 中间板连接器(2 个) 2. 插入器模块 3. 底座连接器(4 个) 卸下底部插入器模块 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 注: 您必须卸下底部插入器模块才能更换出现故障的模块,安装半宽或全宽底座,或维修系统内部的其他组件。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3.
● 系统护盖 ● 冷却风扇 ● 冷却风扇固定框架 步骤 1. 翻转系统,使其底部朝上。 2. 从系统底部: a. 卸下用于固定底部隔板的五颗螺钉。 图 49: 卸下和安装用于固定底部隔板的螺钉 i. 系统底部 ii. 螺钉(5 颗) b. 拧下用于固定底部插入器模块的两颗螺钉。 图 50: 拧下和安装用于固定底部插入器模块的螺钉 i. 系统底部 ii. 螺钉(2 颗) 3. 翻转系统,使其顶侧朝上。 4. 拧下将顶部隔板固定至系统顶部的两颗螺钉。 5.
图 51: 卸下和安装底部隔板 a. 底部隔板 b. 螺钉(2 颗) 6. 拧下将底部插入器模块固定至系统顶部的两颗螺钉。 7. 将底部插入器模块从系统拉出。 图 52: 卸下和安装底部插入器模块 a. 底部插入器模块(2 个) b.
卸下 I/O 模块 页面上的 42 卸下 PCIe 模块 页面上的 43 卸下系统护盖 页面上的 32 卸下冷却风扇 页面上的 49 卸下冷却风扇固定框架 页面上的 51 安装底部插入器模块 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下底部插入器模块。 注: 您必须卸下底部插入器模块才能更换出现故障的模块,安装半宽或全宽底座,或维修系统内部的其他组件。 步骤 1. 将底部插入器模块滑入系统的下部托架中,直至插入器模块上的插针插入中间板上的连接器。 2. 安装将底部插入器模块固定至系统顶部的两颗螺钉。 3. 将底部隔板滑到系统的下部托架中。 4.
相关信息 卸下底部插入器模块 页面上的 57 卸下顶部插入器模块 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 注: 您必须卸下顶部插入器模块才能更换出现故障的模块,安装半宽或全宽底座,或维修系统内部的其他组件。 注: 您必须卸下底部插入器模块,然后再卸下顶部插入器模块。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下以下组件: ● 底座 ● 电源设备 ● CMC 模块 ● I/O 模块 ● PCIe 模块(如果适用) ● 系统护盖 ● 冷却风扇 ● 冷却风扇固定框架 ● 底部插入器模块 步骤 1. 翻转系统,使其底部朝上。 2. 从系统底部: a.
图 54: 卸下和安装将顶部插入器模块固定至中间板的螺钉 i. 中间板 ii. 系统底部 iii. 螺钉(2 颗) 3. 翻转系统,使其顶侧朝上。 4. 拧下将顶部隔板固定至系统顶部的三颗螺钉。 5. 将顶部隔板滑出系统。 图 55: 卸下和安装顶部隔板 a. 顶部隔板 b. 螺钉(3 颗) 6. 拧下将顶部插入器模块固定至系统顶部的两颗螺钉。 7.
图 56: 卸下和安装顶部插入器模块 a. 顶部插入器模块 b. 螺钉(2 颗) 后续步骤 安装顶部插入器模块。 相关任务 安装顶部插入器模块 页面上的 63 卸下计算底座 页面上的 33 卸下存储底座 页面上的 35 卸下电源设备单元 页面上的 47 卸下 CMC 模块 页面上的 40 卸下 I/O 模块 页面上的 42 卸下 PCIe 模块 页面上的 43 卸下系统护盖 页面上的 32 卸下冷却风扇 页面上的 49 卸下冷却风扇固定框架 页面上的 51 卸下底部插入器模块 页面上的 57 安装顶部插入器模块 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3.
2. 拧紧将顶部插入器模块固定至系统顶部的两颗螺钉。 3. 将顶部隔板滑入系统。 4. 拧紧将顶部隔板固定至系统顶部的三颗螺钉。 5. 翻转系统,使其底部朝上。 6. 拧紧将顶部插入器模块固定至中间板的两颗螺钉。 7. 拧紧将顶部隔板固定至中间板的顶部隔板的两颗螺钉。 8. 翻转系统,使其顶侧朝上。 后续步骤 1. 安装以下组件: ● 底部插入器模块 ● 冷却风扇固定框架 ● 冷却风扇 ● 系统护盖 ● PCIe 模块(如果适用) ● I/O 模块 ● CMC 模块 ● 电源设备 ● 底座 2.
3. 卸下以下组件: ● 底座 ● 电源设备 ● CMC 模块 ● I/O 模块 ● 系统护盖 ● 冷却风扇 ● 冷却风扇固定框架 ● PCIe 模块和 PCIe 交换机板(如果适用) ● 风扇接口板(如果适用) ● 插入器模块(如果适用) 步骤 1. 从中间板提起聚脂薄膜绝缘材料。 2. 卸下连接至中间板的两根风扇电缆。 3. 拧下将风扇电缆夹固定至系统的两颗螺钉。 图 57: 卸下和安装中间板部件组件 1. 中间板 3. 螺钉(2 颗) 2. 风扇电缆夹(2 个) 4. 聚脂薄膜绝缘材料 4. 拧下将中间板部件固定至系统的五颗螺钉。 图 58: 卸下和安装中间板 1. KVM 电缆 3. 控制面板电缆 2. 中间板 4.
5. 电缆护盖 7. 电源插入器板 6. 电源总线条 5. 拧下将电缆管固定在机箱左侧的螺钉。 6. 从电缆管中卸下控制面板电缆。 7. 从 KVM 面板正面拧下固定 KVM 面板的螺钉。 8. 拧下用于固定 KVM 盖的螺钉。 9. 拧下将电缆管固定在机箱右侧的螺钉。 10. 将电缆管放置在机箱上,无需卸下 KVM 面板电缆和 KVM 面板。 11. 从系统中抬起中间板部件,并将其置于机箱顶部。 注: 卸下中间板部件并将其置于机箱上时应小心,以防止损坏 KVM 和控制面板电缆。 图 59: 卸下和安装电缆管 1. 3. 5. 7. 9. KVM 护盖上的螺钉 KVM 面板上的六角螺钉(2 个) 机箱左侧的电缆管 电缆管上的卡舌 KVM 面板电缆 2. 4. 6. 8. 10. KVM 面板护盖 KVM 面板 电缆管上的固定螺钉(6 个) 控制面板电缆 机箱右侧的电缆管 12. 垂直向上推动 KVM 电缆闩锁以从中间板上的连接器上断开电缆的连接。 13.
图 60: 在中间板上布线 KVM 和控制面板电缆 1. 3. 5. 7. KVM 电缆连接器 中间板部件上的支架,用于 KVM 电缆布线 中间板部件上的支架,用于控制面板电缆布线 中间板上的连接器 2. KVM 电缆 4. 控制面板电缆 6. 控制面板电缆连接器 14. 从系统中取出中间板部件。 后续步骤 1.
安装中间板部件 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下中间板部件。 注: 必须卸下中间板部件才能更换出现故障的组件。 步骤 1. 中间板部件的支架中布线 KVM 和控制面板电缆。 2. 将 KVM 和控制面板电缆重新连接至中间板部件各自的连接器。 3. 将中间板部件放入系统中。 4. 拧回用于将中间板部件固定到系统的五颗螺钉。 5. 安装两颗螺钉,以将风扇电缆夹固定至系统的螺钉。 6. 重新连接用于连接中间板的两根风扇电缆。 7. 通过将电缆插入风扇电缆夹来固定风扇电缆。 8. 将 KVM 电缆连接器重新连接至 KVM 面板中的连接器。 9.
安装计算底座 页面上的 34 相关信息 卸下中间板部件 页面上的 64 电源插入器板 卸下电源插入器板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下中间板部件。 步骤 1. 卸下聚脂薄膜绝缘材料。 2. 从中间板部件断开电源总线条和电缆护盖的连接。 3. 从电源插入器板断开电源总线条和电缆护盖的连接。 4. 拧下将电源插入器板固定至托盘的四颗螺钉。 5. 从托盘中取出电源插入器板。 图 61: 卸下和安装电源插入器板 a. 螺钉(4 颗) b. 电源插入器板 c.
安装电源插入器板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下电源插入器板。 注: 您必须卸下电源插入器板才能更换出现故障的电源插入器板。 步骤 1. 将电源插入器板放到托盘中。 2. 拧紧四颗螺钉,将电源插入器板固定至托盘。 3. 将电源总线条和电缆护盖重新连接至电源插入器板。 4. 将电源总线条和电缆护盖重新连接至中间板部件。 5. 安装聚脂薄膜绝缘材料。 后续步骤 1. 安装中间板部件。 2.
图 62: 卸下和安装电缆管 1. 控制面板 3. 电缆管 2. 螺钉(5 颗) 4. 控制面板电缆 3. 拧下将控制面板护盖固定至控制面板的螺钉。 4. 拨开 ZIF 连接器闩锁。 5. 使用推拉卡舌将控制面板电缆从控制面板中卸下。 注: 为防止损坏控制面板电缆,从控制面板拔下控制面板电缆时要格外小心。 6. 从系统中卸下控制面板。 图 63: 卸下和安装控制面板 1. ZIF 连接器闩锁 3. 控制面板护盖 2. 连接器 4.
安装控制面板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下控制面板。 注: 您必须卸下控制面板才能更换出现故障的控制面板。 步骤 1. 将控制面板电缆连接至控制面板。 2. 将 ZIF 连接器释放闩锁按入到位。 3. 拧紧螺钉,将控制面板护盖固定到控制面板上。 4. 将控制面板上的螺孔与系统侧面的螺孔对齐。 5. 拧紧将控制面板固定至系统侧面的两颗螺钉。 6. 将控制面板电缆插入电缆管。 7. 将电缆管上的螺孔与系统侧面的螺孔对齐。 8.
图 64: 卸下和安装电缆管 1. KVM 面板电缆 3. 电缆管 2. 螺钉(5 颗) 4. KVM 面板 3. 拧下将 KVM 面板护盖固定至 KVM 面板的螺钉。 4. 拨开连接器闩锁。 5. 从 KVM 面板卸下 KVM 面板电缆。 注: 为防止损坏 KVM 面板电缆,将 KVM 面板电缆从 KVM 面板上拔下时要格外小心。 6. 卸下 KVM 面板。 图 65: 卸下和安装 KVM 面板 1. 螺钉 3. 连接器 5. KVM 面板护盖 2. KVM 面板电缆 4.
相关任务 安装 KVM 面板 页面上的 74 安装 KVM 面板 前提条件 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电话服务和支持小组指导 下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的安全说明。 注: 这是一个可现场更换单元 (FRU)。卸下和安装步骤只能由 Dell 认证的维修技术人员执行。 1. 确保已阅读安全说明 页面上的 31。 2. 请按照拆装计算机内部组件之前 页面上的 31 中的步骤进行操作。 3. 卸下 KVM 面板。 注: 您必须卸下 KVM 面板才能更换出现故障的面板。 步骤 1. 将 KVM 面板电缆连接至 KVM 面板。 2. 将连接器闩锁按入到位。 3. 拧上螺钉以将 KVM 面板护盖固定至 KVM 面板。 4. 将 KVM 面板上的螺孔与系统侧面的螺孔对齐。 5. 拧上将 KVM 面板固定至系统侧面的两颗螺钉。 6. 将 KVM 面板电缆插入电缆管。 7. 将电缆管上的螺孔与系统侧面的螺孔对齐。 8.
5 系统故障排除 注: 本章仅提供针对 PowerEdge FX2 和 FX2s 机柜的故障排除信息。有关底座的故障排除信息,请参阅位于 Dell.com/ poweredgemanuals 的底座说明文件。 安全第一 — 为您和您的系统着想 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 主题: • • • • • 对系统管理警报消息作出响应 外部连接故障排除 受损机柜故障排除 机柜组件故障排除 I/O 模块故障排除 对系统管理警报消息作出响应 Chassis Management Controller (CMC) 管理应用程序监测关键系统电压和温度以及系统中的冷却风扇。有关 CMC 警报消息的信息, 请参阅位于 Dell.
机柜组件故障排除 以下步骤说明如何对机柜组件进行故障排除。 受潮机柜故障排除 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 步骤 1. 关闭系统和已连接的外围设备。 2. 断开电源设备与 PDU 或电源插座的连接。 小心: 等到所有电源设备上的指示灯均熄灭后再继续。 3. 将以下组件从系统卸下: a. b. c. d. e. f. g. 底座 电源设备 I/O 模块 冷却风扇 冷却风扇托架 CMC 模块 PCIe 模块 小心: 通过空气干燥,不要使用毛巾。 4. 使系统彻底干燥至少 24 小时。 5. 重新安装您在步骤 3 中卸下的组件。 6.
5. 如果问题仍然存在,请参阅获得帮助。 电源设备不匹配故障排除 PowerEdge FX2 机箱单元支持各种电源设备 (PSU) 型号。在系统配置中混合使用不同的 PSU 型号时,可能会发生 PSU 不匹配的情 况。 步骤 1. 在经过一个交流电源循环后或者在连接更换的 PSU 时,系统会检查 PSU 是否不匹配。 2. PSU 手柄中的 LED 指示灯呈绿色闪烁几次,然后熄灭,此顺序表示存在 PSU 不匹配的情况。 注: 在机箱管理控制器 (CMC) 日志中会生成严重警报信息。该日志提供有关 PSU 冗余状态的信息,还指出该 PSU 是否与安 装的其他 PSU 兼容。 3. 使用已知合适的 PSU 更换不兼容的 PSU。 4.
扩展卡故障排除 前提条件 小心: 多数维修只能由经认证的维修技术人员进行。您只能根据产品说明文件中的授权,或者在联机或电话服务和支持团队的指 导下进行故障排除和简单维修。任何未经 Dell 授权的服务所导致的损坏均不在保修范围之列。请阅读并遵循产品附带的安全说 明。 注: 进行扩充卡故障排除时,请参阅操作系统和扩充卡的说明文件。 步骤 1. 从底座运行相应的诊断测试。 如果测试运行失败,请转至步骤 3。 2. 登录 CMC Web 界面。 3. 在 PCIe 属性中,验证 PCIe 插槽是否分配到底座。 有关更多信息,请参阅 Dell.com/esmmanuals 上的 Dell PowerEdge FX2 CMC 用户指南。 4. 关闭底座。 5. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 6. 卸下 PCIe 模块。 7. 确保每个扩展卡都已在其连接器中稳固就位。 8. 重新安装 PCIe 模块。 9. 如果问题仍未解决,请关闭系统和连接的外围设备,然后断开系统与电源插座的连接。 10. 卸下 PCIe 模块。 11. 卸下系统中安装的所有扩展卡。 12. 重新安装 PCIe 模块。 13.
● 尝试使用外部交换机或集线器上的另一个连接器。 ● 如果活动指示灯不亮,请更换网络交换机模块。 6. 使用交换机管理界面验证交换机端口的属性。如果交换机正确配置,请备份交换机配置并更换交换机。有关详情,请参阅交换机 模块说明文件。 7. 确保在底座中已安装相应的网络子卡 (NDC)。如果底座上的网络链路指示灯显示绿色,则底座具有到 I/O 模块的有效链路。 8.
6 技术规格 - PowerEdge FX2/FX2s 主题: • • • • • • • • 尺寸和重量 底座规格 电源规格 Chassis Management Controller(CMC)规格 机柜控制面板规格 I/O 模块规格 环境规格 扩展操作温度 尺寸和重量 物理 尺寸 宽度 含机架吊耳 481.9 毫米(18.97 英寸) 不含机架吊耳 43.35 厘米(17.06 英寸) 高度 86.80 毫米(3.4 英寸) 深度(不带挡板) 851.6 毫米(33.52 英寸) 最大配置重量 53 千克(116.8 磅) 净重 21.5 千克 (47.
存储底座 规格 多达两个 PowerEdge FD332 存储底座映射到多达四个 PowerEdge FC430 计算底座,或 多达两个 PowerEdge FD332 存储底座映射到一个 PowerEdge FC830 计算底座,或 注: 有关计算底座和存储底座技术规格的更多信息,请参阅 Dell.com/poweredgemanuals 上相关的底座用户手册。 注: 有关 PowerEdge FX2s 机柜中映射存储底座到计算底座的信息,请参阅位于 Dell.
I/O 模块规格 注: 有关 I/O 模块技术规格的信息,请参阅位于 Dell.com/poweredgemanuals 的 I/O 模块说明文件。 环境规格 注: 有关特定系统配置的环境测量值的附加信息,请参阅 Dell.com/environmental_datasheets。 温度 规格 最高温度梯度(操 作和存储) 20 °C/h (36 °F/h) 存储温度范围 –40 °C 至 65 °C(–40 °F 至 149 °F) 相对湿度 规格 存储 最大露点为 33 °C (91 °F) 时,相对湿度为 5% 至 95%。空气必须始终不冷凝。 温度(连续操 作) 规格 温度范围(在低于 在设备无直接光照的情况下,10 °C 至 35 °C(50 °F 至 95 °F)。 海拔 950 米或 3117 英尺时) 湿度百分比范围 最大露点为 26 °C (78.8 °F) 时,相对湿度为 10% 至 80%。 最大振动 规格 运行时 5 Hz 至 350 Hz 时,0.26 Grms(所有操作方向)。 存储 10 Hz 至 500 Hz 时,1.
微粒污染 规格 注: 仅适用于数据中心环境。空气过滤要求不适用于旨在数据中心之外(诸如办公室或工厂车间等环境) 使用的 IT 设备。 注: 进入数据中心的空气必须拥有 MERV11 或 MERV13 过滤。 导电灰尘 空气中不得含有导电灰尘、锌晶须或其他导电颗粒。 注: 适用于数据中心和非数据中心环境。 腐蚀性灰尘 ● 空气中不得含有腐蚀性灰尘。 ● 空气中的残留灰尘的潮解点必须小于 60% 相对湿度。 注: 适用于数据中心和非数据中心环境。 气体污染 规格 铜片腐蚀率 <300 Å/月,按照 ANSI/ISA71.04-1985 定义的 G1 类标准。 银片腐蚀率 <200 Å/月,按照 AHSRAE TC9.
7 获取帮助 主题: 联系 Dell EMC 找到系统的服务标签 通过使用 QRL 访问系统信息 • • • 联系 Dell EMC Dell EMC 提供了几种联机以及电话支持和服务选项。如果没有可用的互联网连接,可在购货发票、装箱单、帐单或 Dell EMC 产品目 录上查找联系信息。具体的服务随您所在国家/地区以及产品的不同而不同,某些服务在您所在的地区可能不提供。要就销售、技术 帮助或客户服务问题联系 Dell EMC: 步骤 1. 转至 www.dell.com/support/home。 2. 从页面右下角的下拉菜单中选择您所在的国家/地区。 3. 对于定制的支持: a. 在输入您的服务编号字段中,输入您的系统服务编号。 b. 单击提交。 此时将显示其中列出各种支持类别的支持页面。 4. 对于一般支持: a. 选择您的产品类别。 b. 选择您的产品领域。 c. 选择您的产品。 此时将显示其中列出各种支持类别的支持页面。 5. 有关联系 Dell EMC 全球技术支持的详细信息: a. 单击 全球技术支持。 b.
● 您的系统服务标签,以快速访问您的特定硬件配置和保修信息 ● 转至 Dell 的链接 ,用于联系技术支持和销售组队 步骤 1. 请转至 Dell.com/QRL 并导航至您的特定产品或 2.