Dell PowerEdge FX2 and FX2s Enclosure Owner's Manual Regulatory Model: E24S Regulatory Type: E24S001 June 2020 Rev.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2014 ~2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소 유자의 상표일 수 있습니다.
Contents Chapter 1: Dell PowerEdge FX2/FX2s 정보.....................................................................................6 본 문서에 사용된 용어....................................................................................................................................................... 6 슬레드 슬롯 번호 지정....................................................................................................................................................... 7 전면 패널 구조 및 표시등 - PowerEdge FX2/FX2s............
권장 도구.............................................................................................................................................................................32 시스템 덮개........................................................................................................................................................................ 33 시스템 덮개 분리................................................................................................................................................
제어판 분리...................................................................................................................................................................73 제어판 설치...................................................................................................................................................................75 KVM 패널..................................................................................................................................................................
1 Dell PowerEdge FX2/FX2s 정보 Dell PowerEdge FX2/FX2s는 최대 4개의 절반 너비 컴퓨팅 슬레드, 최대 8개의 1/4 너비 컴퓨팅 슬레드, 최대 2개의 전체 너비 컴 퓨팅 슬레드 또는 혼합된 유형의 컴퓨팅 슬레드를 지원할 수 있는 2U 인클로저입니다. PowerEdge FX2s 인클로저는 또한 컴퓨 팅 슬레드에 매핑된 절반 너비 저장소 슬레드를 지원합니다. 노트: PowerEdge FX2s 인클로저 내의 컴퓨팅 슬레드에 매핑된 저장소 슬레드의 매핑 구성에 관한 정보는 Dell PowerEdge FD332 소유자 매뉴얼 (Dell.com/poweredgemanuals)을 참조하십시오. 노트: PowerEdge FX2는 저장소 슬레드를 지원하지 않습니다. 인클로저와 슬레드가 단일 시스템으로 작동하려면 먼저 슬레드를 인클로저에 설치해야 합니다.
표 1. 본 문서에 사용된 용어 (계속) 용어 설명 4베이 섀시 최대 4개의 절반 너비 컴퓨팅 슬레드를 지원하는 PowerEdge FX2/FX2s 인클로저 의 구성을 말합니다. 노트: PowerEdge FX2s에서 4베이 섀시 구성은 절반 너비 컴퓨팅 및 저장소 슬레드의 조합을 지원합니다. 컴퓨팅 슬레드에 매핑된 최대 3개의 저장소 슬 레드를 지원합니다. 8베이 섀시 최대 8개의 1/4 너비 컴퓨팅 슬레드를 지원하는 PowerEdge FX2/FX2s 인클로저 의 구성을 말합니다. 2베이 섀시 최대 2개의 전체 너비 컴퓨팅 슬레드를 지원하는 PowerEdge FX2/FX2s 인클로저 의 구성을 말합니다. 3베이 섀시 1개의 전체 너비 컴퓨팅 슬레드와 최대 2개의 절반 너비 컴퓨팅 슬레드를 지원하 는 PowerEdge FX2/FX2s 인클로저의 구성을 말합니다.
그림 3 . 슬레드 슬롯 번호 지정 - 2베이 섀시 그림 4 . 슬레드 슬롯 번호 지정 - 6베이 섀시 그림 5 . 슬레드 슬롯 번호 지정 - 3베이 섀시 전면 패널 구조 및 표시등 - PowerEdge FX2/FX2s 그림 6 . 전면 패널 구조 및 표시등 - PowerEdge FX2/FX2s 표 2. 전면 패널 구조 및 표시등 - PowerEdge FX2/FX2s 항목 표시등, 단추 또는 커넥터 1 시스템 ID 단추 8 아이콘 Dell PowerEdge FX2/FX2s 정보 설명 전면 및 후면 패널의 ID 단추를 사용하여 랙 내에서 특정 시스템을 찾을 수 있습니다. 이러한 단추 중 하나를 누르 면 단추 중 하나를 다시 누를 때까지 후면에 있는 시스템 상태 표시등이 점멸됩니다.
표 2. 전면 패널 구조 및 표시등 - PowerEdge FX2/FX2s (계속) 항목 표시등, 단추 또는 커넥터 아이콘 설명 시스템 ID를 설정 및 해제로 전환하려면 누릅니다. 2 인클로저 전원 켜짐 표시등, 전원 단추 인클로저 전원이 켜지면 전원 켜짐 표시등에 불이 켜집 니다. 전원 단추로 시스템에 대한 전원 공급 장치 출력을 제어할 수 있습니다. 자세한 내용은 전원 단추 기능을 참 조하십시오. 3 진단 표시등 오류가 발생하면 진단 표시등이 켜집니다. 자세한 내용 은 진단 표시등을 참조하십시오. 4 KVM 선택 단추 KVM을 슬레드에 매핑할 수 있습니다.
표 3. 진단 표시등 (계속) 상태 표시등 압 조정기 고장)가 있으면 이 표시 등이 호박색으로 깜박입니다. 니다. 전원 공급 장치를 분리한 후 재설치하여 다시 장착합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 온도 표시등 상태 수정 조치 시스템에 열 관련 오류(예: 범위를 벗어난 온도 또는 팬 고장)가 있으 면 이 표시등이 호박색으로 깜박입 니다. 다음과 같은 상태가 없는지 확인합니다. ● 냉각 팬이 분리되었거나 오류가 발생했습니다. ● 시스템 덮개, 냉각 덮개, EMI 필러 패널, 메모리 모듈 보호물 또는 후 면 필러 브래킷이 분리되었습니다. ● 주변 온도가 너무 높습니다. ● 외부 공기 흐름이 막혔습니다. 도움말 얻기를 참조하십시오. PCIe 표시등 상태 수정 조치 PCIe에 오류가 있으면 이 표시등이 호박색으로 깜박입니다. 시스템을 다시 시작하십시오. PCIe 카드에 필요한 드라이버를 업데이트 합니다. 카드를 다시 설치합니다. 문제가 계속되면 도움말 얻기를 참조하 십시오.
후면 패널 구조 및 표시등 - PowerEdge FX2s and FX2 그림 7 . 후면 패널 구조 및 표시등 - PowerEdge FX2s 그림 8 . 후면 패널 구조 및 표시등 - PowerEdge FX2 표 4. 후면 패널 구조 및 표시등 —PowerEdge FX2 및 PowerEdge FX2s 인클로저 항목 표시등, 단추 또는 커넥터 설명 1 직렬 커넥터 CMC 구성용 DB-9 직렬 커넥터. 2 이더넷 커넥터 Gb1 관리 시스템에서 기본 CMC로 네트워크 케이블을 연결합니다. 3 이더넷 커넥터 STK/Gb2(스택) 별도의 인클로저에서 데이지 체인 방식의 CMC에 사용됩니다. 노트: 이 포트는 CMC NIC 페일오버에도 사용할 수 있습니다. 4 시스템 ID 단추 전면과 후면 패널에 있는 ID 단추를 사용하여 랙 내에서 특정 시스템을 찾을 수 있습니다. 이러한 단추 중 하나를 누르면 단추 중 하나를 다시 누를 때까지 후면에 있는 시스템 상태 표시등이 점멸됩니다.
표 4. 후면 패널 구조 및 표시등 —PowerEdge FX2 및 PowerEdge FX2s 인클로저 (계속) 항목 표시등, 단추 또는 커넥터 설명 2400W(저전압의 경우 1400W) 전원 공급 장치(PSU2) 7 1100W(저전압의 경우 1050W) 1600W(저전압의 경우 800W) 2000W(저전압의 경우 1000W) 2400W(저전압의 경우 1400W) 8 I/O 모듈(2) 인클로저에서 컴퓨트 슬레드로의 이더넷 연결을 제공합니다. 9 I/O 모듈 포트 I/O 모듈의 네트워크 인터페이스. 10 I/O 모듈 표시등 2개의 표시등 용도: ● 상태 ● 전원 전원 공급 장치(PSU) 표시등 각 AC PSU(전원 공급 장치)에는 불빛이 비치는 반투명 핸들이 있고, 이 핸들은 전원 공급 여부 또는 전원 결함 발생 여부를 나타 내는 표시등 역할을 합니다. AC PSU는 PDU(배전 장치) 또는 전원 콘센트에 연결되어 있어야 합니다. 그림 9 . PSU 표시등 1.
표 5. PSU 표시등 (계속) 규칙 전원 표시등 패턴 상태 주의: 사용되는 모든 전원 공급 장치의 유형과 최대 출력 전원은 동일해야 합니다. 노트: FX2 섀시는 1100W, 1600W, 2000W 또는 2400W의 정격 용량을 가진 PSU만 지 원합니다. C 녹색 점멸 및 꺼짐 PSU를 핫 애드할 때 PSU 핸들이 녹색으로 5회 깜박인 후 꺼집니다. 이는 PSU 불일치를 나타냅니다. 꺼짐 전원이 연결되어 있지 않습니다. I/O 모듈 표시등 그림 10 . I/O 모듈 표시등(패스 스루 모듈) 그림 11 . I/O 모듈 표시등(스위치 모듈) 1. 전원 표시등 2. 상태 표시등 표시등은 다음 정보를 제공합니다. 전원 표시등 패 턴 설명 녹색 I/O 모듈이 정상적으로 작동하고 있습니다. 꺼짐 I/O 모듈의 전원이 꺼져 있습니다. 상태 표시등 패 턴 설명 파란색 I/O 모듈이 정상적으로 작동하고 있습니다. 파란색으로 깜박임 CMC가 I/O 모듈 식별하는 중입니다.
CMC 모듈 그림 12 . CMC 모듈 1. 로컬 구성용 DB-9 직렬 커넥터 2. 이더넷 커넥터 Gb1 3. 링크 표시등 4. 작동 표시등 5. 이더넷 커넥터 STK/Gb2(스택) 6. 시스템 식별 버튼 노트: 이 포트는 CMC NIC 페일오버에도 사용할 수 있습 니다. CMC 표시등 인클로저의 후면판에 있는 CMC 표시등은 다음과 같은 정보를 제공합니다. Indicator(표시 설명 등) 시스템 ID 단추 상태 표시등 전면 및 후면 패널의 ID 단추를 사용하여 랙 내에서 특정 시스템을 찾을 수 있습니다. 이러한 단추 중 하나 를 누르면 단추 중 하나를 다시 누를 때까지 후면에 있는 시스템 상태 표시등이 점멸됩니다. 시스템 ID를 설정 및 해제로 전환하려면 누릅니다. 파란색 CMC가 활성상태이고 정상적으로 작동하고 있습니다. 황색 CMC에 오류가 있습니다. CMC 기능 CMC는 다음과 같은 여러 가지 시스템 관리 기능을 제공합니다.
● 구성요소의 열 차단을 위해 인클로저의 냉각 팬이 최대 속도로 작동됩니다. 데이지 체인 CMC 네트워크 연결 각 CMC에는 레이블이 Gb1(업링크 포트) 및 STK/Gb2(스태킹 또는 케이블 통합 포트)인 두 개의 RJ-45 이더넷 포트가 있습니 다. 기본 케이블 연결에서는 Gb 포트를 관리 네트워크에 연결하고 STK/Gb2 포트는 사용하지 않는 상태로 둘 수 있습니다. 주의: STK/Gb2를 관리 네트워크에 연결하는 경우 CMC 설정을 기본 스태킹에서 중복으로 변경하지 않으면 NIC 페일오버 를 구현하는 데 예상치 않은 결과를 초래할 수 있습니다 기본 스태킹 보드에서는 Gb1 및 STK/Gb2 포트를 동일한 네트워크 (브로드캐스트 도메인)에 연결하게 되어 브로드캐스트 스톰이 발생할 수 있습니다.브로드캐스트 스톰은 CMC 설정이 중복 으로 변경되어도 발생할 수 있지만 케이블 연결은 스태킹 모드의 새시 간 데이지 체인 방식으로 구성됩니다.
냉각 팬 표시등 코드 각 냉각 팬에는 냉각 팬의 전원 상태를 표시하는 LED가 있습니다. 표시등 패턴 상태 꺼짐 냉각 팬은 올바로 작동하고 있습니다. 주황색 점멸 냉각 팬의 문제를 표시합니다. 그림 14 . 냉각 팬 표시등 1. 상태 표시등 구성 마법사 CMC(Chassis Management Controller)는 고정 IP 주소를 사용하도록 미리 구성되었습니다. DHCP(Dynamic Host Configuration Protocol)를 사용하려면 다음과 같이 하십시오. 1. 2. 3. 4. CMC(Chassis Management Controller)에 액세스합니다. Network(네트워크)를 클릭합니다. IPv4 또는 IPv6을 클릭합니다. DHCP Enable(DHCP 활성화)을 선택합니다. 자세한 내용은 Dell PowerEdge FX2/FX2s CMC 사용 설명서(Dell.com/esmmanuals)를 참조하십시오.
문서 매트릭스 문서 매트릭스는 사용자의 시스템을 설정하고 관리하기 위해 참조할 수 있는 문서들에 대한 정보를 제공합니다. 표 6. 문서 매트릭스 목적 을(를) 참조하십시오. 랙에 시스템 설치 랙 솔루션과 함께 제공되는 랙 설명서 시스템을 설치하고 시스템의 기술적 사양 이해 시작 안내서 운영 체제 설치 운영 체제 설명서(Dell.com/operatingsystemmanuals) Dell Systems Management 제안서 개요 보기 Dell OpenManage Systems Management (Dell.com/openmanagemanuals) CMC(Chassis Management Controller) 설치, 구성 및 사용 Dell PowerEdge FX2/FX2s CMC 사용자 설명서(Dell.
● ● ● ● 방법 동영상 소유자 매뉴얼, LCD 진단 및 기계 개요를 포함한 참조 자료 특정 하드웨어 구성 및 보증 정보에 빠르게 액세스하기 위한 시스템 서비스 태그 기술 지원 및 영업팀에 직접 연락할 수 있는 Dell 링크 단계 1. Dell.com/QRL로 이동하고 특정 제품을 탐색하거나 2. 스마트폰 또는 태블릿을 사용하여 다음 이미지나 Dell PowerEdge 시스템에 있는 모델별 QR 코드를 스캔합니다.
2 초기 시스템 구성 주제: • • • 시작하기 전에 PowerEdge FX2/FX2s 설치 CMC에 로그인 시작하기 전에 주의: 인클로저 전원 공급 장치는 PDU 또는 전원 콘센트에 연결해야 합니다. 전원 공급 장치에는 100V ~ 120V 또는 200V ~ 240V의 전원이 필요합니다. 시스템이 두 범위에서 동시에 작동하지 않으므로 하나의 AC 전원 입력만 선택할 수 있습니 다. ● 해당하는 경우, 컴퓨팅 슬레드의 모든 PCIe 카드 펌웨어와 iDRAC 펌웨어를 업데이트합니다. ● Dell.com/support에서 최신 버전의 CMC 펌웨어를 다운로드합니다. 또한 시스템에 포함된 Dell 시스템 관리 도구 및 설명서 DVD가 있는지 확인합니다. ● 네트워크에서 고정 주소 지정을 사용하는 경우 IP 주소, 서브넷 마스크 및 게이트웨이가 있어야 인클로저에서 CMC 및 기타 모듈을 구성할 수 있습니다. PowerEdge FX2/FX2s 설치 단계 1.
● 컴퓨팅 슬레드 중 하나에 연결하고 HII(Human Interface Infrastructure) 브라우저로 부팅하여 CMC IP 주소를 검색합니 다. 10. 기본 로그온 자격 증명을 사용하여 웹 브라우저를 통해 CMC IP 주소에 연결합니다. 노트: CMC의 기본 IP 주소는 192.168.0.120입니다. 기본 사용자 이름은 root이고 암호는 calvin입니다. 11. CMC 웹 인터페이스에서 각 iDRAC에 IP 주소를 제공합니다. 12. 웹 브라우저를 사용하여 각 iDRAC를 연결하고 iDRAC의 최종 구성을 입력합니다. 기본 사용자 이름은 root이고 암호는 calvin입니다. 13. 컴퓨팅 슬레드의 전원을 켜고 운영 체제를 설치합니다. 다음 단계 인클로저의 포장 풀기 및 설치에 대한 단계별 지침을 보려면 QR 코드를 스캔하십시오. QR 찾기에 대한 자세한 정보는 QRL을 사 용하여 시스템 정보에 액세스 페이지 17을(를) 참조하십시오. 그림 15 .
3 PowerEdge FX2/FX2s 매핑 구성 이 섹션에서는 인클로저의 I/O 모듈, PCIe 슬롯, CMC로의 컴퓨팅 슬레드 연결에 대한 정보를 제공합니다. ● LOM 네트워크 및 컴퓨트 슬레드의 I/O 모듈 포트로의 매핑 구성 ● 확장 버스 및 컴퓨트 슬레드의 PCIe 확장 슬롯으로의 매핑 구성 ● 내부 관리 네트워크 노트: 컴퓨팅 슬레드의 I/O 모듈 포트 매핑 및 PCIe 슬롯 매핑은 사전 구성됩니다. 주제: • • • • • LOM(LAN On Motherboard) 네트워크 I/O 모듈 및 PCIe 메자닌 카드 구성 지침 I/O 모듈의 네트워크 설정 구성 확장 버스 내부 관리 네트워크 LOM(LAN On Motherboard) 네트워크 LOM(LAN On Motherboard) 네트워크는 PowerEdge FX2/FX2s 인클로저의 후면에 설치된 I/O 모듈에 의해 슬레드로 제공되는 이더넷 연결을 말합니다.
노트: 컴퓨팅 슬레드에 매핑된 저장소 슬레드를 지원하는 4베이 PowerEdge FX2s 구성에서 I/O 모듈 포트는 컴퓨팅 슬레드 에만 매핑됩니다. 저장소 슬레드가 설치된 경우 이러한 슬롯에 매핑된 I/O 모듈의 해당 포트는 활성화되지 않습니다. 그림 16 . I/O 모듈 포트 매핑 - 듀얼 포트 NDC를 포함한 절반 너비 컴퓨팅 슬레드 듀얼 포트 NDC(네트워크 도터 카드)로 구성된 절반 너비 컴퓨팅 슬레드는 각 I/O 모듈의 단일 포트로 매핑됩니다. 다음 표에는 컴퓨팅 슬레드와 매핑된 포트가 표시됩니다. 표 7. I/O 모듈 포트 매핑 - 절반 너비 컴퓨팅 슬레드(듀얼 포트 NDC) 컴퓨팅 슬레드 IO 모듈 A1(상단) IO 모듈 A2(하단) 1 1 1 2 3 3 3 5 5 4 7 7 그림 17 .
표 8. I/O 모듈 포트 매핑 - 절반 너비 컴퓨팅 슬레드(쿼드 포트 NDC/네트워크 출력) (계속) 컴퓨팅 슬레드 IO 모듈 A1(상단) IO 모듈 A2(하단) 3 5,6 5,6 4 7,8 7,8 I/O 모듈 포트 매핑 - 8베이 섀시 최대 8개의 1/4 너비 컴퓨팅 슬레드를 지원하는 8베이 섀시에서는 컴퓨팅 슬레드가 각 I/O 모듈의 단일 포트로 매핑됩니다. 그림 18 . I/O 모듈 포트 매핑 - 8베이 섀시 다음 표에는 컴퓨팅 슬레드와 매핑된 포트가 표시됩니다. 표 9. 8베이 섀시의 I/O 모듈 포트 매핑 컴퓨팅 슬레드 IO 모듈 A1(상단) IO 모듈 A2(하단) 1a 1 1 1b 2 2 1c 3 3 1d 4 4 3a 5 5 3b 6 6 3c 7 7 3d 8 8 I/O 모듈 포트 매핑 - 6베이 섀시 6베이 섀시는 최대 4개의 1/4 너비 컴퓨팅 슬레드와 최대 2개의 절반 너비 컴퓨팅 슬레드의 조합을 지원합니다.
그림 19 . I/O 모듈 포트 매핑 - 6베이 섀시 다음 표에는 컴퓨팅 슬레드와 매핑된 포트가 표시됩니다. 표 10.
표 11. I/O 모듈 포트 매핑 - 전체 너비 컴퓨팅 슬레드 컴퓨팅 슬레드 I/O 모듈 A1(상단) I/O 모듈 A2(하단) 1 1, 2, 3, 4 1, 2, 3, 4 3 5, 6, 7, 8 5, 6, 7, 8 I/O 모듈 포트 매핑 - 3베이 섀시 3베이 섀시는 1개의 전체 너비 컴퓨팅 슬레드와 최대 2개의 절반 너비 컴퓨팅 슬레드의 조합을 지원합니다. 3베이 섀시에서 전체 너비 컴퓨팅 슬레드는 각 I/O 모듈의 4개의 포트에 매핑됩니다. 1/4 포트 NDC를 포함하는 절반 너비 컴퓨 팅 슬레드는 각 I/O 모듈의 2개의 포트에 매핑됩니다. 노트: 이중 포트 NDC로 구성된 절반 너비 컴퓨팅 슬레드가 각 I/O 모듈의 2개 포트로 매핑됩니다. 노트: 전체 너비 컴퓨팅 슬레드에 매핑된 저장소 슬레드를 지원하는 3베이 PowerEdge FX2s 구성에서는 컴퓨팅 슬레드만 I/O 모듈 포트에 매핑 가능합니다.
● PowerEdge FX2s 인클로저에 설치된 절반 또는 1/4 너비 컴퓨팅 슬레드는 각각 1개의 PCIe 메자닌 카드를 지원합니다. 전체 너비 컴퓨팅 슬레드는 각각 2개의 PCIe 메자닌 카드를 지원합니다. 컴퓨팅 슬레드의 PCIe 확장 버스 슬롯을 찾으려면 관련 컴퓨팅 슬레드 소유자 매뉴얼(Dell.com/poweredgemanuals)을 참조하십시오. PCIe 메자닌 카드는 인클로저의 PCIe 확장 슬롯에 매핑됩니다. 자세한 내용은 PCIe 확장 슬롯 매핑 페이지 26을(를) 참조하십시오. 노트: PCIe 메자닌 카드만 컴퓨팅 슬레드에 설치할 수 있습니다. 이더넷, 파이버 채널 또는 InfiniBand 메자닌 카드 등 PCIe가 아닌 메자닌 카드는 지원되지 않습니다. PCIe가 아닌 메자닌 카드를 슬레드에 설치하면 슬레드에서 주황색 등이 깜박이면서 불일치 상태를 나타내고 슬레드의 전원이 켜지지 않습니다.
그림 22 . PCIe 슬롯에 매핑된 컴퓨팅 슬레드 - 4베이 섀시 그림 23 . PCIe 슬롯에 매핑된 컴퓨팅 슬레드 - 8베이 섀시 그림 24 .
그림 25 . PCIe 슬롯에 매핑된 컴퓨팅 슬레드 - 2베이 섀시 그림 26 . PCIe 슬롯에 매핑된 컴퓨팅 슬레드 - 3베이 섀시 저장소 슬레드에 매핑된 컴퓨팅 슬레드의 PCIe 슬롯 매핑 컴퓨팅 슬레드에 매핑된 저장소 슬레드를 지원하는 PowerEdge FX2s 인클로저 구성에서, PCIe 슬롯은 컴퓨팅 슬레드에만 매핑 됩니다. 인클로저에 저장소 슬레드가 설치된 경우 이러한 베이에 매핑된 PCIe 슬롯이 자동으로 인클로저의 상단 베이에 설치된 컴퓨팅 슬레드에 자동으로 재할당됩니다. PCIe 슬롯 재할당 기능은 하단 베이의 컴퓨팅 슬레드의 PCIe 슬롯을 상단 베이의 컴퓨 팅 슬레드에 재할당할 수 있도록 해줍니다. PCIe 슬롯 재할당 기능은 저장소 슬레드의 포함 여부와 상관없이 인클로저 구성에 적용됩니다. CMC 웹 인터페이스, CMC WSMAN 또는 RACADM을 사용하여 PCIe 재할당 옵션을 활성화 또는 비활성화할 수 있 습니다.
그림 27 . 저장소 슬레드에 매핑된 컴퓨팅 슬레드에서 매핑된 PCIe 슬롯 - 4베이 섀시 그림 28 . 저장소 슬레드에 매핑된 컴퓨팅 슬레드에서 매핑된 PCIe 슬롯 - 4베이 섀시(1개의 컴퓨팅 슬레드 포함) 그림 29 .
그림 30 . 저장소 슬레드에 매핑된 컴퓨팅 슬레드에서 매핑된 PCIe 슬롯 - 6베이 섀시 PCIe 슬롯 관리 시스템의 PCIe 슬롯이 개별적으로 작동하거나 동시에 작동할 때의 상태를 확인할 수 있습니다.CMC 웹 인터페이스를 통한 PCIe 슬롯 관리에 대한 자세한 내용은 Dell PowerEdge FX2/FX2s CMC 사용자 설명서(Dell.com/esmmanuals)를 참조하십시오. 내부 관리 네트워크 내부 관리 네트워크 연결은 컴퓨팅 슬레드의 iDRAC와 CMC 간의 이더넷 관리 연결을 제공합니다.
4 PowerEdge FX2/FX2s 인클로저 구성부품 설치 및 제거 이 섹션에서는 인클로저 구성부품의 설치 및 제거하는 방법에 대한 내용을 제공합니다. 슬레드 구성부품의 제거 및 설치에 대한 자세한 내용은 해당 슬레드 소유자 매뉴얼 (Dell.com/poweredgemanuals)을 참조하십시오. 주제: • • • • • • • • • • • • • • • • • • • • • 고객 및 현장 교체 가능한 부품(CRU) - PowerEdge FX2/FX2s 안전 지침 컴퓨터 내부 작업을 시작하기 전에 컴퓨터 내부 작업을 마친 후에 권장 도구 시스템 덮개 슬레드 시스템 내부 CMC 모듈 I/O 모듈 PCIe 모듈 확장 카드 전원 공급 장치 냉각 팬 냉각 팬 케이지 PCIe 스위치 보드 팬 인터페이스 보드 점속기 모듈 중앙판 조립품 제어판 KVM 패널 고객 및 현장 교체 가능한 부품(CRU) - PowerEdge FX2/FX2s 고객 및 현장 교체 가능한 부품(CRU)은 다음과 같습니다.
● KVM 패널 안전 지침 노트: 시스템을 들어 올려야 할 경우에는 다른 사람의 도움을 받으십시오. 부상당할 우려가 있으므로 혼자 힘으로 시스템을 들어 올리지 마십시오. 노트: 시스템이 켜져 있는 상태에서 시스템 덮개를 열거나 분리하면 감전의 위험에 노출될 수 있습니다. 노트: 시스템이 켜진 상태에서 구성요소를 분리하거나 설치할 때는 감전되지 않도록 주의해야 합니다. 주의: 덮개가 없는 상태에서 3분을 초과하여 시스템을 작동하지 마십시오. 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 시스템 내부의 구성요소를 다룰 때는 항상 정전기 방지 매트와 접지대를 사용하는 것이 좋습니다.
시스템 덮개 시스템 덮개 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 적절한 작동과 냉각을 위해 시스템 덮개를 분리한 후 3분 이내에 다시 덮어야 합니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 단계 1. 덮개 잠금 장치를 시계 반대 방향으로 돌려 잠금 해제 위치에 둡니다. 2. 시스템 양쪽의 분리 래치를 덮개 잠금 장치 쪽으로 누릅니다. 3. 덮개를 시스템 전면 쪽으로 민 다음 덮개를 시스템에서 들어올려 분리합니다. 그림 31 . 시스템 덮개 분리 및 설치 a. 분리 래치(2개) b.
시스템 덮개 장착 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. 시스템 덮개를 분리합니다. 노트: 시스템 내부의 구성요소를 수리하려면 시스템 덮개를 분리해야 합니다. 단계 1. 덮개 잠금 장치 반대편의 덮개 하단 모서리를 시스템 슬롯 안에 놓습니다. 2. 덮개를 시스템 위에 내려 놓습니다. 3. 시스템 덮개가 시스템 표면에 맞추어 질때까지 시스템 덮개를 시스템 후면으로 밉니다. 4. 덮개 잠금 장치를 시계 방향으로 돌려 잠금 위치에 놓습니다.
주의: 슬레드를 영구적으로 분리하는 경우 슬레드 보호물을 설치합니다. 슬레드 보호물을 설치하지 않고 오랫동안 시스 템을 작동하면 인클로저가 과열될 수 있습니다. 그림 32 . 컴퓨팅 슬레드 분리 및 설치 1. 인클로저 3. 컴퓨트 슬레드 핸들 2. 컴퓨팅 슬레드 4. 슬레드 핸들의 분리 단추 다음 단계 컴퓨팅 슬레드 또는 슬레드 보호물을 설치합니다. 관련 태스크 컴퓨팅 슬레드 설치 on page 35 컴퓨팅 슬레드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 단계 1.
4. 슬레드 커넥터가 중앙판 커넥터와 단단히 연결될 때까지 슬레드를 인클로저에 밀어 넣습니다. 슬레드를 인클로저로 밀어 넣으면 슬레드 핸들이 인클로저 쪽으로 회전됩니다. 5. 분리 단추가 제자리에 고정될 때까지 슬레드 핸들을 닫힘 위치로 누릅니다. 다음 단계 컴퓨팅 슬레드의 전원을 켭니다. 관련 정보 컴퓨팅 슬레드 분리 on page 34 저장소 슬레드 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 주의: 데이터 손실의 결과로 저장소 슬레드 전원이 켜지면 저장소 슬레드를 인클로저에서 분리합니다.
그림 33 . 저장소 슬레드 분리 a. 슬레드 잠금 장치(2개) b. 저장소 슬레드의 점선 c. 슬레드 분리 래치(2개) 그림 34 . I/O 커넥터 덮개 분리 및 설치 a. 저장소 슬레드 b. I/O 커넥터 덮개 다음 단계 저장소 슬레드 또는 슬레드 보호물을 설치합니다.
관련 태스크 저장소 슬레드 설치 on page 38 저장소 슬레드 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 주의: I/O 커넥터의 손상을 방지하려면 커넥터 또는 커넥터 핀을 만지지 마십시오. 주의: 슬레드 잠금 장치의 손상을 방지하려면 #2 십자 드라이버를 사용해 슬레드 잠금 장치의 위치를 변경합니다. 노트: PowerEdge FX2s 인클로저의 하단 왼쪽 슬롯부터(슬롯 3) 차례로 저장소 슬레드를 설치합니다. 4 베이 섀시의 경우 인클로저의 상단 오른쪽 슬롯(슬롯2)에 저장소 슬레드를 설치할 수도 있습니다.
그림 35 . 저장소 슬레드 설치 a. 저장소 슬레드의 점선 b. 슬레드 잠금 장치(2개) 다음 단계 저장소 슬레드가 매핑된 컴퓨팅 슬레드를 켜면 저장소 슬레드가 켜집니다. 관련 참조 안전 지침 on page 32 관련 정보 저장소 슬레드 분리 on page 36 시스템 내부 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 핫 스왑 가능한 구성부품은 주황색으로 표시되고, 구성부품의 접촉점은 파란색으로 표시됩니다.
그림 36 . 시스템 내부 - PowerEdge FX2s 1. 3. 5. 7. 중앙판 전원 버스 바 전원 공급 장치(2개) CMC 모듈 2. 팬(8개) 4. 전원 점속기 보드 6. PCIe 모듈(8개) 노트: PowerEdge FX2는 PCIe 모듈을 지원하지 않습니다. CMC 모듈 본 시스템은 여러 시스템 관리 기능을 제공하는 핫 스왑 가능한 CMC 모듈을 지원합니다.
CMC 모듈 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 결함이 있는 CMC 모듈을 교체하거나 시스템 내부의 다른 구성 요소를 수리하려면 모듈을 제거해야 합니다. 노트: CMC 모듈은 핫 스왑이 가능합니다. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 단계 1. CMC 모듈에 연결된 케이블의 연결을 끊습니다. 2. 분리 래치를 누르고 섀시에서 전원 공급 장치 모듈을 밀어 빼냅니다. 그림 37 . CMC 모듈 분리 및 설치 a. CMC 모듈 b. CMC 모듈 손잡이 c. 분리 래치 다음 단계 CMC 모듈을 설치합니다.
단계 1. CMC 모듈의 포장을 풀고 설치를 준비합니다. 2. CMC 모듈 커넥터가 중앙판의 핀과 연결될 때까지 CMC 모듈을 인클로저에 밀어 넣습니다. 3. CMC 모듈에 케이블을 연결합니다. 관련 정보 CMC 모듈 분리 on page 41 CMC 모듈 SD 카드 CMC 모듈의 SD 카드 슬롯은 WWN/MAC 기능(선택 사양)을 지원하여 슬레드용 슬롯 기반 WWN/MAC를 사용할 수 있으며 슬 레드를 더 쉽게 설치 및 교체할 수 있습니다. 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. CMC 모듈을 분리합니다.
I/O 모듈 시스템은 외부 네트워크 연결을 제공하는 최대 두 개의 핫 스왑 가능한 I/O 모듈을 지원합니다. I/O 모듈 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 결함이 있는 I/O 모듈을 교체하거나 시스템 내부의 다른 구성 요소를 수리하려면 모듈을 제거해야 합니다. 노트: I/O 모듈은 핫 스왑이 가능합니다. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 단계 1. I/O 모듈에 연결된 케이블을 분리합니다. 2. 분리 래치를 누르고 인클로저에서 I/O 모듈을 밀어 빼냅니다. 그림 39 . I/O 모듈 분리 및 설치 a. I/O 모듈 b. I/O 모듈 핸들 c.
단계 1. I/O 모듈의 포장을 풀고 설치를 준비합니다. 지침을 보려면 I/O 모듈과 함께 제공된 설명서를 참조하십시오. 2. I/O 모듈이 중앙판의 커넥터와 연결되고 분리 래치가 제자리에 고정될 때까지 밉니다. 3. I/O 모듈에 연결해야 하는 케이블을 모두 연결합니다. 해당 케이블 연결에 대한 정보는 I/O 모듈의 설명서를 참조하십시오. 관련 정보 I/O 모듈 분리 on page 43 PCIe 모듈 PowerEdge FX2s는 8개의 PCIe 모듈을 지원합니다. 각 PCIe 모듈에는 로우 프로파일 확장 카드를 설치할 수 있는 1개의 확장 카 드 슬롯이 포함되어 있습니다. 노트: PowerEdge FX2는 PCIe 모듈을 지원하지 않습니다. PCIe 모듈 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다.
다음 단계 PCIe 모듈을 설치합니다. 관련 태스크 PCIe 모듈 설치 on page 45 PCIe 모듈 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 주의: PCIe 모듈은 웜 스왑 방식 구성요소입니다. 각 PCIe 모듈은 슬레드에 할당되어 있기 때문에 PCIe 모듈이 할당된 슬 레드의 전원이 켜져 있을 때 PCIe 모듈을 분리 또는 추가하면 오류가 발생할 수 있습니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. PCIe 모듈을 분리합니다.
확장 카드 작동 전원 상태 다음 표는 컴퓨팅 슬레드에 매핑된 PCIe 슬롯에 확장 카드를 설치 시 작동 전원 상태에 대한 정보를 제공합니다. 표 14. 확장 카드 작동 전원 상태 섀시 상태 컴퓨팅 슬레드 상태 확장 카드 상태 꺼짐 꺼짐 꺼짐 대기 모드 꺼짐 꺼짐 켜짐 꺼짐 꺼짐 켜짐 켜짐 켜짐 다음 표는 PCIe 슬롯에서 교체 시 확장 카드의 작동 전원 상태에 대한 정보를 제공합니다. 표 15. 확장 카드 작동 전원 상태 섀시 상태 컴퓨팅 슬레드 상태 확장 카드 상태 켜짐 꺼짐 꺼짐 켜짐 켜짐 꺼짐 노트: PCIe 슬롯의 전원이 켜져 있는지 확인하려면 PCIe 모듈 표시등 페이지 46를 참조하십시오. PCIe 모듈 표시등 PCIe 확장 카드 슬롯은 웜 스왑이 가능합니다. 확장 카드는 연결된 컴퓨팅 슬레드의 전원이 꺼지면 전원이 꺼집니다. PCIe 모듈 표시등은 모듈 내부의 PCIe 슬롯에 대한 다음 정보가 표시됩니다.
2. 확장 카드의 모서리 부분을 잡고 PCIe 모듈에 있는 확장 카드 커넥터에서 분리합니다. 3. 카드를 영구적으로 분리하는 경우 빈 확장 슬롯 입구에 금속 필러 브래킷을 설치한 다음 분리 래치를 닫습니다. 노트: 시스템의 미국 연방 통신위원회(FCC) 인증을 유지하려면 필러 브래킷을 빈 확장 카드 슬롯에 설치해야 합니다. 브 래킷은 또한 시스템 안으로 먼지 및 이물질이 들어오는 것을 막고, 시스템 내부가 적절히 냉각되며 공기가 흐르도록 도 와줍니다. 필러 브래킷은 적절한 발열 상태를 유지하는 데 필요합니다. 그림 41 . 확장 카드 분리 및 설치 a. 확장 카드 b. 분리 래치 다음 단계 1. PCIe 모듈을 설치합니다. 2. 확장 카드가 매핑된 컴퓨팅 슬레드의 전원을 켭니다. 관련 태스크 PCIe 모듈 분리 on page 44 PCIe 모듈 설치 on page 45 확장 카드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
단계 1. 확장 카드의 포장을 풀고 설치를 준비합니다. 자세한 내용은 카드와 함께 제공된 설명서를 참조하십시오. 2. 카드의 모서리를 잡고 카드 에지 커넥터가 PCIe 모듈의 확장 카드 커넥터에 맞춰지도록 카드를 놓습니다. 3. 카드가 완전히 장착될 때까지 카드 에지 커넥터를 확장 카드 커넥터에 단단히 삽입합니다. 4. 확장 카드 분리 래치를 닫습니다. 다음 단계 1. PCIe 모듈을 설치합니다. 2. 확장 카드가 할당된 컴퓨팅 슬레드의 전원을 켭니다. 관련 태스크 PCIe 모듈 분리 on page 44 PCIe 모듈 설치 on page 45 전원 공급 장치 시스템은 1+1 중복 또는 2+0 비중복 구성을 기준으로 2개의 핫스왑 가능한 전원 공급 장치(PSU)를 지원합니다. 주의: 지원되지 않는 PSU 구성에서는 PSU 불일치 조건 및 전원 켜기 장애가 발생할 수 있습니다. 노트: 모든 PSU의 정격 출력 용량, 세대 및 입력 전압이 같은지 확인합니다.
그림 42 . PSU 분리 및 설치 1. 분리 래치 3. PSU 5. PSU 핸들 2. PSU 케이블 커넥터 4. 커넥터 다음 단계 1. PSU를 장착합니다. 2. 전원 케이블을 PSU에 연결하고 케이블을 전원 콘센트에 연결합니다. 관련 태스크 전원 공급 장치(PSU) 설치 on page 49 전원 공급 장치(PSU) 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 새 전원 공급 장치를 설치하거나 핫 스왑 또는 핫 애드할 경우, 시스템이 PSU를 인식하고 상태를 확인하는데 몇 초간 의 시간이 걸립니다. PSU가 제대로 작동하는 경우 PSU 상태 표시등이 녹색으로 변합니다.
냉각 팬 이 시스템은 시스템의 I/O 구성요소를 냉각하는 8개의 핫 스왑이 가능한 팬을 지원합니다. 시스템에서 PCIe 구성요소를 효율적으로 냉각시키려면 CMC 웹 인터페이스에서 팬 오프셋 옵션을 변경할 수 있습니다. 팬 오프셋 옵션에 대한 자세한 내용은 CMC 온라인 도움말 에서 고급 팬 구성 을 참조하십시오. 노트: 팬을 분리할 경우, 즉시 다른 팬으로 교체합니다. 팬을 설치하지 않고 장기간 시스템을 작동하면 인클로저가 과열될 수 있습니다. 노트: 특정 팬에 문제가 있는 경우, 팬 번호는 시스템의 관리 소프트웨어로 참조되기 때문에 냉각 팬 베이의 팬 번호를 참조 하여 적절한 팬을 쉽게 확인하고 교체할 수 있습니다. 팬 중 하나라도 고장나면 팬의 LED가 켜집니다. 노트: 시스템의 냉각 팬은 80mm, 60mm 정사각 두 가지 크기로 제공됩니다. 냉각 팬 분리 전제조건 노트: 시스템이 켜져 있는 상태에서 시스템 덮개를 열거나 분리하면 감전의 위험에 노출될 수 있습니다.
그림 43 . 냉각 팬 분리 및 설치 a. 냉각 팬 케이지 b. 팬 분리 탭 c. 냉각 팬(8개) 다음 단계 냉각 팬 모듈을 설치합니다. 관련 태스크 냉각 팬 설치 on page 51 시스템 덮개 분리 on page 33 냉각 팬 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 냉각 팬을 분리합니다. 노트: 결함이 있는 팬을 교체하거나 시스템 내부의 다른 구성 요소를 수리하려면 냉각 팬을 제거해야 합니다. 단계 1. 냉각 팬 베이스에 있는 플러그를 PCIe 스위치/팬 인터페이스 보드에 맞춥니다. 2.
관련 태스크 시스템 덮개 장착 on page 34 관련 정보 냉각 팬 분리 on page 50 냉각 팬 케이지 냉각 팬 케이지 분리 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 노트: 다른 시스템 내부의 구성요소를 수리하려면 냉각 팬 케이지를 분리해야 합니다. 1. 2. 3. 4. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 시스템 덮개를 분리합니다. 냉각 팬을 분리합니다.
그림 45 . 냉각 팬 케이지 상단 보기 a. 나사 위치(6개) 다음 단계 냉각 팬 케이지를 설치합니다. 관련 태스크 냉각 팬 케이지 설치 on page 53 시스템 덮개 분리 on page 33 냉각 팬 분리 on page 50 냉각 팬 케이지 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3.
시스템 덮개 장착 on page 34 관련 정보 냉각 팬 케이지 분리 on page 52 PCIe 스위치 보드 PCIe 스위치 보드는 PowerEdge FX2s 인클로저에서 지원됩니다. 다음 절차는 PowerEdge FX2s 인클로저에 적용됩니다. PCIe 스위치 보드 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다.
그림 46 . PCIe 스위치 보드 분리 및 설치 1. 분리 래치 3. 노치(4개) 2. 레버(2개) 4. 스프링 나사(2개) 다음 단계 PCIe 스위치 보드를 설치합니다. 관련 태스크 PCIe 스위치 보드 설치 on page 55 시스템 덮개 분리 on page 33 냉각 팬 분리 on page 50 냉각 팬 케이지 분리 on page 52 PCIe 모듈 분리 on page 44 PCIe 스위치 보드 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다.
단계 1. PCIe 스위치 보드를 시스템 안쪽으로 내립니다. 노트: PCIe 스위치 보드 하단에 있는 탭이 시스템의 노치에 연결되었는지 확인합니다. 2. 커넥터가 중앙판의 핀과 확실히 연결될 때까지 PCIe 스위치 보드를 밉니다. 3. PCIe 스위치 보드가 제자리에 고정될 때까지 레버를 밉니다. 4. 스프링 나사 2개를 조여 PCIe 스위치 보드를 시스템에 고정합니다. 다음 단계 1. 다음을 설치합니다. ● PCIe 모듈 ● 냉각 팬 케이지 ● 냉각 팬 ● 시스템 덮개 2. 컴퓨터 내부 작업을 마친 후에 페이지 32의 절차를 따릅니다. 관련 태스크 PCIe 모듈 설치 on page 45 냉각 팬 케이지 설치 on page 53 냉각 팬 설치 on page 51 시스템 덮개 장착 on page 34 관련 정보 PCIe 스위치 보드 분리 on page 54 팬 인터페이스 보드 팬 인터페이스 보드는 PowerEdge FX2 인클로저에서 지원됩니다. 다음 절차는 FX2 인클로저에만 적용됩니다.
그림 47 . 팬 인터페이스 보드 분리 및 설치 a. 그립(2개) b. 노치(4개) c. 스프링 나사(2개) 다음 단계 팬 인터페이스 보드를 장착합니다. 관련 태스크 팬 인터페이스 보드 설치 on page 57 시스템 덮개 분리 on page 33 냉각 팬 분리 on page 50 냉각 팬 케이지 분리 on page 52 팬 인터페이스 보드 설치 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2.
노트: 팬 인터페이스 보드 후면의 탭이 시스템의 노치와 연결되어야 합니다. 2. 팬 인터페이스 보드를 커넥터가 중앙판의 핀에 확실히 연결될 때까지 밉니다. 3. 스프링 나사 2개를 조여 팬 인터페이스 보드를 시스템에 고정합니다. 다음 단계 1. 다음을 설치합니다. ● 냉각 팬 케이지 ● 냉각 팬 ● 시스템 덮개 2. 컴퓨터 내부 작업을 마친 후에 페이지 32의 절차를 따릅니다. 관련 태스크 냉각 팬 케이지 설치 on page 53 냉각 팬 설치 on page 51 시스템 덮개 장착 on page 34 관련 정보 팬 인터페이스 보드 분리 on page 56 점속기 모듈 점속기 모듈로 절반 너비 또는 전체 너비 슬레드가 사전 설치되어 제공되는 PowerEdge FX2/FX2s 인클로저 내에 1/4 슬레드를 설치할 수 있습니다.
그림 48 . 점속기 모듈의 상단 1. 중앙판 커넥터(2개) 2. 점속기 모듈 3. 슬레드 커넥터(4개) 하단 점속기 모듈 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 노트: 결함이 있는 모듈을 교체하거나 절반/전체 너비 슬레드를 설치하거나, 시스템 내부의 다른 구성 요소를 수리하려면 하단 점속기 모듈을 제거해야 합니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2.
● ● ● ● ● ● CMC 모듈 I/O 모듈 PCIe 모듈(해당하는 경우) 시스템 덮개 냉각 팬 냉각 팬 케이지 단계 1. 시스템의 하단이 위를 향하도록 시스템을 뒤집습니다. 2. 시스템 하단에서, a. 하단 파티션을 고정시키는 나사를 제거합니다. 그림 49 . 하단 파티션을 고정하는 나사 제거 및 장착 i. 시스템 하단 ii. 나사(5개) b. 하단 점속기 모듈을 고정하는 나사 2개를 제거합니다. 그림 50 . 하단 점속기 모듈을 고정하는 나사 제거 및 장착 i. 시스템 하단 ii. 나사(2개) 3. 시스템의 상단이 위를 향하도록 시스템을 뒤집습니다. 4. 하단 파티션을 시스템 상단에 고정하는 2개의 나사를 제거합니다. 5. 하단 파티션을 시스템에서 밀어 꺼냅니다.
그림 51 . 하단 파티션 분리 및 설치 a. 하단 파티션 b. 나사(2개) 6. 하단 점속기 모듈을 시스템 상단에 고정하는 2개의 나사를 제거합니다. 7. 하단 점속기 모듈을 시스템에서 당겨 뺍니다. 그림 52 . 하단 점속기 모듈 분리 및 설치 a. 하단 장착 모듈(2개) b. 나사(2개) 다음 단계 하단 점속기 모듈을 설치합니다.
CMC 모듈 분리 on page 41 I/O 모듈 분리 on page 43 PCIe 모듈 분리 on page 44 시스템 덮개 분리 on page 33 냉각 팬 분리 on page 50 냉각 팬 케이지 분리 on page 52 하단 점속기 모듈 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3.
전원 공급 장치(PSU) 설치 on page 49 저장소 슬레드 설치 on page 38 컴퓨팅 슬레드 설치 on page 35 관련 정보 하단 점속기 모듈 분리 on page 59 상단 점속기 모듈 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 노트: 결함이 있는 모듈을 교체하거나 절반/전체 너비 슬레드를 설치하거나, 시스템 내부의 다른 구성 요소를 수리하려면 상단 점속기 모듈을 제거해야 합니다.
그림 53 . 상단 파티션을 중앙판에 고정하는 나사 분리 및 설치 i. 중앙판 ii. 시스템 하단 iii. 나사(3개) b. 상단 점속기 모듈을 중앙판에 고정하는 나사 2개를 분리합니다. 그림 54 . 상단 점속기 모듈을 중앙판에 고정하는 나사 분리 및 설치 i. 중앙판 ii. 시스템 하단 iii. 나사(2개) 3. 시스템의 상단이 위를 향하도록 시스템을 뒤집습니다. 4. 나사 3개를 풀어 상단 파티션을 시스템 상단에서 분리합니다. 5. 상단 파티션을 시스템에서 밀어 꺼냅니다.
그림 55 . 상단 파티션 분리 및 설치 a. 상단 파티션 b. 나사(3개) 6. 나사 2개를 풀어 상단 점속기 모듈을 시스템 상단에서 분리합니다. 7. 상단 점속기 모듈을 시스템에서 당겨 뺍니다. 그림 56 . 상단 점속기 모듈 분리 및 설치 a. 상단 점속기 모듈 b. 나사(2개) 다음 단계 상단 점속기 모듈을 설치합니다.
CMC 모듈 분리 on page 41 I/O 모듈 분리 on page 43 PCIe 모듈 분리 on page 44 시스템 덮개 분리 on page 33 냉각 팬 분리 on page 50 냉각 팬 케이지 분리 on page 52 하단 점속기 모듈 분리 on page 59 상단 점속기 모듈 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2.
PCIe 모듈 설치 on page 45 I/O 모듈 설치 on page 43 CMC 모듈 설치 on page 41 전원 공급 장치(PSU) 설치 on page 49 저장소 슬레드 설치 on page 38 컴퓨팅 슬레드 설치 on page 35 관련 정보 상단 점속기 모듈 분리 on page 63 중앙판 조립품 중앙판 조립품에는 중앙판, 전원 점속기 보드, 전원 케이블, 버스 바가 포함됩니다. 중앙판 조립품 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다.
그림 57 . 중앙판 조립품 구성요소 분리 및 설치 1. 중앙판 3. 나사(2개) 2. 팬 케이블 클립(2개) 4. 마일라 절연체 4. 중앙판 조립품을 시스템에 고정하는 나사 5개를 분리합니다. 그림 58 . 중앙판 분리 및 설치 1. 3. 5. 7. KVM 케이블 콘솔 케이블 케이블 덮개 전원 점속기 보드 2. 중앙판 4. 중앙판 조립품 나사(5개) 6. 전원 버스 바 5. 섀시의 왼쪽에 있는 케이블 튜브를 고정하는 나사를 제거합니다. 6. 제어판 보드 케이블을 케이블 튜브에서 제거합니다. 7. KVM 패널 보드를 고정하는 KVM 패널의 전면에 있는 나사를 제거합니다. 8. KVM 덮개를 고정하는 나사를 제거합니다. 9. 섀시의 오른쪽에 있는 케이블 튜브를 고정하는 나사를 제거합니다. 10. KVM 패널 케이블 및 KVM 패널을 분리하지 않고 섀시에 케이블 튜브를 올려 놓습니다. 11. 중앙판 조립품을 시스템에서 들어 올리고 섀시의 상단에 올려 놓습니다.
그림 59 . 케이블 튜브 분리 및 설치 1. 3. 5. 7. 9. KVM 덮개의 나사 KVM 패널의 육각 나사(2개) 섀시 왼쪽에 있는 케이블 튜브 케이블 튜브의 탭 KVM 패널 케이블 2. 4. 6. 8. 10. KVM 패널 덮개 KVM 패널 보드 케이블 튜브의 나사(6개) 콘솔 케이블 섀시 오른쪽에 있는 케이블 튜브 12. KVM 케이블 래치를 세로로 눌러 중앙판의 커넥터에서 케이블을 분리합니다. 13. 중앙판의 커넥터에서 제어판 케이블 커넥터를 분리합니다.
그림 60 . 중앙판의 KVM 및 제어판 케이블 배선 2. KVM 케이블 1. KVM 케이블 커넥터 3. KVM 케이블을 배선하기 위해 중앙판 조립품에 있는 브래 4. 콘솔 케이블 킷 5. 제어판 케이블을 배선하기 위해 중앙판 조립품에 있는 브 6. 제어판 케이블 커넥터 래킷 7. 중앙판의 커넥터 14. 중앙판 조립품을 들어 올려 시스템에서 꺼냅니다. 다음 단계 1. 중앙판 조립품을 설치합니다.
중앙판 조립품 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. 중앙판 조립품을 분리합니다. 노트: 결함이 있는 조립품을 교체하려면 중앙판 조립품을 분리해야 합니다. 단계 1. KVM 및 제어판 케이블을 중앙판 조립품의 브래킷에 배선합니다. 2.
전원 공급 장치(PSU) 설치 on page 49 저장소 슬레드 설치 on page 38 컴퓨팅 슬레드 설치 on page 35 관련 정보 중앙판 조립품 분리 on page 67 전원 점속기 보드 전원 점속기 보드 분리 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. 중앙판 조립품을 분리합니다. 단계 1.
c. 캐리어 다음 단계 전원 점속기 보드를 설치합니다. 전원 점속기 보드 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. 전원 점속기 보드를 분리합니다. 노트: 결함이 있는 전원 점속기 보드를 교체하려면 전원 점속기 보드를 분리해야 합니다. 단계 1. 전원 점속기 보드를 캐리어에 놓습니다. 2.
단계 1. 케이블 튜브를 시스템 측면에 고정하는 나사 3개를 풀어 케이블 튜브를 분리합니다. 2. 제어판을 시스템에 고정하는 나사 2개를 분리합니다. 그림 62 . 케이블 튜브 분리 및 설치 1. 콘솔 3. 케이블 튜브 2. 나사(5개) 4. 콘솔 케이블 3. 제어판 덮개를 제어판에 고정하는 나사를 분리합니다. 4. ZIF 커넥터 래치를 분리합니다. 5. 당김 탭을 사용하여 제어판 케이블을 제어판에서 분리합니다. 노트: 제어판 케이블의 손상을 방지하려면 제어판 케이블을 제어판에서 분리 시 각별한 주의가 요구됩니다. 6. 제어판을 시스템에서 분리합니다. 그림 63 . 제어판 분리 및 설치 1. ZIF 커넥터 래치 3. 제어판 덮개 다음 단계 제어판을 장착합니다. 74 PowerEdge FX2/FX2s 인클로저 구성부품 설치 및 제거 2. 커넥터 4.
관련 태스크 제어판 설치 on page 75 제어판 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. 제어판을 분리합니다. 노트: 결함이 있는 제어판을 교체하려면 제어판을 분리해야 합니다. 단계 1. 컨트롤 패널 케이블을 컨트롤 패널에 연결합니다. 2. ZIF 커넥터 분리 래치를 제자리에 누릅니다. 3.
2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 단계 1. 케이블 튜브를 시스템 측면에 고정하는 나사 3개를 풀어 케이블 튜브를 분리합니다. 2. KVM 패널을 시스템에 고정하는 나사 2개를 분리합니다. 그림 64 . 케이블 튜브 분리 및 설치 1. KVM 패널 케이블 3. 케이블 튜브 2. 나사(5개) 4. KVM 패널 3. KVM 패널 덮개를 KVM 패널에 고정하는 나사를 분리합니다. 4. 커넥터 래치를 분리합니다. 5. KVM 패널 케이블을 KVM 패널에서 분리합니다. 노트: KVM 패널 케이블의 손상을 방지하려면 KVM 패널 케이블을 KVM 패널에서 분리 시 각별한 주의가 요구됩니다. 6. KVM 패널을 분리합니다. 그림 65 . KVM 패널 분리 및 설치 1. 나사 3. 커넥터 76 PowerEdge FX2/FX2s 인클로저 구성부품 설치 및 제거 2. KVM 패널 케이블 4.
5. KVM 패널 덮개 다음 단계 KVM 패널을 장착합니다. 관련 태스크 KVM 패널 설치 on page 77 KVM 패널 설치 전제조건 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문 서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시 오. 노트: 이 제품은 현장 교체 가능 장치(FRU)입니다. 분리 및 설치 절차는 Dell 공인 서비스 기술자에 의해서만 수행할 수 있습 니다. 1. 안전 지침 페이지 32을(를) 읽고 숙지하십시오 2. 컴퓨터 내부 작업을 시작하기 전에 페이지 32의 절차를 따릅니다. 3. KVM 패널을 분리합니다. 노트: 결함이 있는 패널을 교체하려면 KVM 패널을 분리해야 합니다. 단계 1.
5 시스템 문제 해결 노트: 이 장에는 PowerEdge FX2 및 FX2s 인클로저에만 적용되는 문제 해결 정보가 나와 있습니다. 슬레드 문제 해결 정보 는 Dell.com/poweredgemanuals에서 슬레드 설명서를 참조하십시오. 안전 제일 — 사용자 및 시스템 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
인클로저 구성요소 문제 해결 다음 절차에서는 인클로저 구성요소 문제를 해결하는 방법에 대해 설명합니다. 습식 인클로저 문제 해결 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 단계 1. 시스템 및 장착된 주변 장치의 전원을 끕니다. 2. PDU 또는 전원 콘센트에서 전원 공급 장치를 분리합니다. 주의: 전원 공급 장치의 모든 표시등이 꺼질 때까지 기다린 다음 계속합니다. 3. 시스템에서 다음 구성요소를 분리합니다. a. b. c. d. e. f. g. 슬레드 전원 공급 장치 I/O 모듈 냉각 팬 냉각 팬 베이 CMC 모듈 PCIe 모듈 주의: 자연 건조시키고 수건을 사용하지 마십시오.
4. 모든 전원 공급 장치에 결함 LED가 표시되지 않고 슬레드가 켜지지 않으면 CMC에서 상태 메시지를 확인합니다. 자세한 내 용은 Dell PowerEdge FX2 CMC 사용 설명서(Dell.com/esmmanuals)를 참조하십시오. 5. 문제가 계속되면 도움말 얻기를 참조하십시오. 전원 공급 장치 불일치 문제 해결 PowerEdge FX2 섀시 장치는 다양한 PSU(전원 공급 장치) 모델을 지원합니다. 서로 다른 PSU 모델을 함께 사용하여 시스템을 구성하면 PSU 불일치 인스턴스가 발생할 수 있습니다. 단계 1. 시스템은 AC 전원 주기 후 또는 교체 PSU가 연결될 때 PSU 불일치를 확인합니다. 2. PSU 핸들의 LED 표시등이 녹색으로 몇 번 깜박인 다음 꺼지면 이 절차에 PSU 불일치 문제가 있음을 의미합니다. 노트: 위험 경고 메시지가 CMC(Chassis Management Controller) 로그에 생성됩니다.
확장 카드 문제 해결 전제조건 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서 비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 확장 카드의 문제를 해결하는 경우 운영 체제 및 확장 카드 설명서를 참조하십시오. 단계 1. 슬레드에서 적절한 진단 검사를 실행합니다. 검사에 실패하면 3단계로 이동합니다. 2. CMC 웹 인터페이스에 로그인합니다. 3. PCIe 속성에서 PCIe 슬롯이 슬레드에 할당되어 있는지 확인합니다. 자세한 내용은 Dell PowerEdge FX2 CMC 사용 설명서(Dell.com/esmmanuals)를 참조하십시오. 4. 슬레드 전원을 끕니다. 5. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 6.
● 링크 표시등에 오류 상태가 표시되면 모든 케이블 연결을 확인하십시오. ● 외부 스위치 또는 허브에서 다른 커넥터로 시도해 보십시오. ● 작동 표시등이 켜지지 않는 경우 네트워크 스위치 모듈을 교체합니다. 6. 스위치 관리 인터페이스를 사용하여 스위치 포트 속성을 확인합니다. 스위치가 올바르게 구성되어 있는 경우 스위치 구성을 백업하고 스위치를 교체합니다. 자세한 내용은 스위치 모듈 설명서를 참조하십시오. 7. 슬레드에 적절한 네트워크 도터 카드(NDC)가 설치되어 있어야 합니다. 슬레드의 네트워크 링크 표시등이 녹색이면 슬레드 에 I/O 모듈의 유효한 링크가 있는 것입니다. 8. 해당 운영 체제 드라이버가 설치되어 있고 프로토콜 설정이 올바르게 통신하도록 구성되어 있는지 확인합니다.
6 기술 사양 - PowerEdge FX2/FX2s 주제: • • • • • • • • 치수 및 무게 슬레드 사양 전원 사양 CMC(Chassis Management Controller) 사양 인클로저 콘솔 사양 I/O 모듈 사양 환경 사양 확대된 작동 온도 치수 및 무게 규격 폭 높이 치수 랙 이어 포함 481.9mm(18.97") 랙 이어 제외 43.35cm(17.06인치) 86.80mm(3.4") 깊이(베젤 불포함) 851.6mm(33.52") 최대 구성일 경우 의 무게 53kg(116.8파운드) 비어 있을 경우의 무게 21.5kg(47.
저장소 슬레드 사양 PowerEdge FX2s 1개의 PowerEdge FC630/FC640 컴퓨팅 슬레드에 매핑된 최대 3개의 PowerEdge FD332 스토리지 슬레드 또는, 2개의 PowerEdge FC630/FC640 컴퓨팅 슬레드에 매핑된 최대 2개의 PowerEdge FD332 스토리지 슬레드 또는, 최대 4개의 PowerEdge FC430 컴퓨팅 슬레드에 매핑된 최대 2개의 PowerEdge FD332 저장소 슬레 드 1개의 PowerEdge FC830 컴퓨팅 슬레드에 매핑된 최대 3개의 PowerEdge FD332 저장소 슬레드 노트: 컴퓨팅 슬레드 및 저장소 슬레드의 기술 사양에 대한 자세한 내용은 관련 슬레드 소유자 매뉴얼(Dell.com/ poweredgemanuals)을 참조하십시오. 노트: PowerEdge FX2s 인클로저 내의 컴퓨팅 슬레드에 매핑된 저장소 슬레드에 관한 정보는 Dell PowerEdge FD332 소유 자 매뉴얼 (Dell.
외부 액세스 가 능 커넥터 사양 동영상 15핀 VGA I/O 모듈 사양 노트: I/O 모듈의 기술 사양에 대한 자세한 내용은 Dell.com/poweredgemanuals에서 I/O 모듈 설명서를 참조하십시오. 환경 사양 노트: 특정 시스템 구성을 위한 환경 측정에 대한 추가 정보는 Dell.com/environmental_datasheets를 참조하십시오. 온도 사양 최대 온도 변화(작 동 및 보관 시) 20°C/h (36 °F/h) 보관 시 온도 한계 –40°C ~ 65°C(–40°F ~ 149°F) 상대 습도 사양 보관 시 최대 이슬점이 33°C(91 °F)인 5% ~ 95% RH. 대기는 항상 비응축 상태여야 함. 온도 (계속적인 사양 작동) 온도 범위 (950m 또는 3117피트 미 만의 고도에서) 장비에 직사광선을 받지 않고 10 °C ~ 35 °C(50 °F ~ 95 °F). 습도 퍼센트(%) 범 26 °C (78.
이 섹션에서는 한계를 정의하여 먼지와 가스 오염으로 부터 IT 장비 손상 및/또는 고장을 피하는데 도움을 줍니다. 에서는 한계 의 레벨 경우 또는 가스 오염 수치 오염이 지정한 한계값이 지나면 및 장비 손상 또는 오류로 인해, 환경을 해결하려면 할 수 있 습니다. 환경을 개선하는 것은 고객의 책임입니다. 미세 먼지 오염 사양 공기 여과 데이터 센터 공기 여과는 ISO Class 8 per ISO 14644-1의 규정에 따라 95% 상위 지수 제한됩니다. 노트: 데이터 센터 환경에만 적용됩니다. 공기 여과 요구사항은 사무실이나 공장 바닥과 같은 환경인 데이터 센터외 공간에서의 IT 장비에는 적용되지 않습니다. 노트: 데이터 센터로 유입되는 공기는 MERV11 또는 MERV13 여과여야 합니다. 전도성 먼지 공기에는 전도성 먼지, 아연 휘스커, 또는 기타 전도성 입자가 없어야 합니다. 노트: 데이터 센터 및 비-데이터 센터 환경에 적용됩니다.
7 도움말 보기 주제: • • • Dell EMC에 문의하기 시스템의 서비스 태그 찾기 QRL을 사용하여 시스템 정보에 액세스 Dell EMC에 문의하기 Dell EMC는 다양한 온라인 및 전화 기반의 지원 및 서비스 옵션을 제공합니다. 인터넷에 연결되어 있지 않은 경우 구매 송장, 포 장 명세서, 청구서 또는 Dell EMC 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell EMC에 문의 하려면 단계 1. www.dell.com/support/home 페이지로 이동합니다. 2. 페이지 우측 하단에 있는 드롭다운 메뉴에서 국가를 선택합니다. 3. 맞춤화된 지원: a. Enter your Service Tag(서비스 태그 입력) 필드에 시스템 서비스 태그를 입력합니다. b. 제출을 클릭합니다.
● ● ● ● 방법 동영상 소유자 매뉴얼, LCD 진단 및 기계 개요를 포함한 참조 자료 특정 하드웨어 구성 및 보증 정보에 빠르게 액세스하기 위한 시스템 서비스 태그 기술 지원 및 영업팀에 직접 연락할 수 있는 Dell 링크 단계 1. Dell.com/QRL로 이동하고 특정 제품을 탐색하거나 2. 스마트폰 또는 태블릿을 사용하여 다음 이미지나 Dell PowerEdge 시스템에 있는 모델별 QR 코드를 스캔합니다.