Dell PowerEdge M520 시스템 소유자 매뉴얼 규정 모델: HHB 규정 유형: HHB004
주, 주의 및 경고 노트: "주"는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제를 방지할 수 있는 방법 을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. Copyright © 2014 Dell Inc. 저작권 본사 소유. 이 제품은 미국, 국제 저작권법 및 지적 재산권법에 의해 보호됩니다. Dell™ 및 Dell 로고는 미국 및/또는 기타 관할지역에서 사용되는 Dell Inc.의 상표입니다. 이 문서에 언급된 기타 모든 표시 및 이름 은 각 회사의 상표일 수 있습니다. 2014 - 10 Rev.
목차 1 시스템 정보..............................................................................................................6 전면 패널 구조 및 표시등....................................................................................................................... 6 USB 디스켓 또는 USB DVD/CD 드라이브 사용..................................................................................... 6 하드 드라이브/SSD 표시등 패턴.............................................................................................................
권장 도구..............................................................................................................................................26 블레이드 분리 및 설치..........................................................................................................................26 블레이드 분리.................................................................................................................................26 블레이드 설치...............................................................................
저장소 컨트롤러 카드...........................................................................................................................55 저장소 컨트롤러 카드 분리.............................................................................................................55 저장소 컨트롤러 카드 설치............................................................................................................ 56 4 시스템 문제 해결...................................................................................................
1 시스템 정보 전면 패널 구조 및 표시등 그림 1 . 전면 패널 구조 및 표시등 1. 블레이드 핸들 분리 단추 2. 하드 드라이브/SSD(2개) 3. 상태/확인 표시등 4. USB 커넥터(2개) 5. 블레이드 전원 단추 USB 디스켓 또는 USB DVD/CD 드라이브 사용 블레이드의 전면에는 USB 디스켓 드라이브, USB 플래시 드라이브, USB DVD/CD 드라이브, 키보드 또는 마우 스를 연결할 수 있는 USB 포트가 있습니다. USB 드라이브는 블레이드를 구성하는 데 사용될 수 있습니다. 노트: 이 블레이드는 Dell USB 2.0 드라이브만 지원합니다. 사용 중인 드라이브를 지원하려면 외부 드라 이브 저장 트레이(선택 사양)을 사용하십시오. 노트: 이 드라이브를 부팅 드라이브로 지정해야 할 경우 USB 드라이브를 연결하고 시스템을 재시작한 다음, 시스템 설정을 시작하고 해당 드라이브를 부팅 순서의 첫 번째 항목으로 설정합니다.
하드 드라이브/SSD 표시등 패턴 하드 드라이브/SSD 표시등은 시스템에서 발생하는 드라이브 이벤트에 따라 여러 가지 다른 패턴을 표시합니 다. 노트: 블레이드의 각 드라이브 베이에는 하드 드라이브/SSD 또는 하드 드라이브 보호물이 설치되어 있 어야 합니다. 그림 2 . 하드 드라이브/SSD 표시등 1. 드라이브 작동 표시등(녹색) 2. 드라이브 상태 표시등(녹색 및 호박색) 노트: 드라이브가 고급 호스트 컨트롤러 인터페이스(AHCI) 모드에 있는 경우, 오 른쪽의 상태 LED는 작동하지 않고 계속 꺼져 있습니다. 드라이브 상태 표시 상태 등 패턴 녹색으로 초당 2번 깜박임 드라이브 식별 또는 분리 준비 상태 꺼짐 드라이브 삽입 또는 분리 대기 상태 노트: 시스템 전원이 공급된 후에 모든 드라이브가 초기화될 때까지 드라이브 상 태 표시등이 꺼진 상태로 유지됩니다. 그 동안에는 드라이브를 삽입하거나 분리할 수 없습니다.
드라이브 상태 표시 상태 등 패턴 녹색으로 켜져 있음 드라이브 온라인 3초 동안 녹색으로 깜박이고 3초 동안 황색으로 깜박이고 6초 동안 꺼짐 재구축 중단 상태 기타 필요한 정보 경고: 시스템과 함께 제공되는 안전 및 규정 정보를 참조하십시오. 보증 정보는 이 문서 안에 포함되어 있 거나 별도의 문서로 제공될 수 있습니다. • 시작 안내서는 시스템 기능, 시스템 설정 및 기술 사양에 대한 개요를 제공합니다. • 랙 솔루션과 함께 제공되는 랙 설치 안내서에는 시스템을 랙에 설치하는 방법이 기술되어 있습니다. • Dell PowerEdge M1000e 인클로저 소유자 매뉴얼은 인클로저 기능에 대한 정보를 제공하고, 인클로저 문 제 해결 방법 및 인클로저 구성부품의 설치 또는 교체 방법을 설명합니다. • Dell 섀시 관리 컨트롤러 사용 설명서는 CMC(Chassis Management Controller) 설치, 구성 및 사용에 대한 정보를 제공합니다.
2 시스템 설정 및 부팅 관리자 사용 시스템 설정을 통해 시스템 하드웨어를 관리하고 BIOS 레벨 옵션을 지정할 수 있습니다. 시작하는 동안 시스템 기능에 액세스하려면 다음 키를 입력합니다. 표 1. 시스템 설정 키 키입력 설명 시스템 설정 페이지를 엽니다. 시스템 서비스를 열고 GUI를 사용하여 운영 체제 배 포, 하드웨어 진단, 펌웨어 업데이트, 및 플랫폼 구성 과 같은 시스템 관리 기능을 지원하는 Dell Lifecycle Controller를 시작합니다. Dell Lifecycle Controller 에서 사용 가능한 기능의 종류는 설치된 Dell iDRAC 라이센스에 의해 결정됩니다. 시스템의 부팅 구성에 따라 BIOS 부팅 관리자 또는 UEFI(Unified Extensible Firmware Interface) 부팅 관 리자를 시작합니다. PXE(Preboot Execution Environment) 부팅을 시작 합니다.
시스템 부팅 모드 선택 시스템 설정을 사용하면 운영 체제를 설치하는 경우의 부팅 모드를 지정할 수 있습니다. • 기본값인 BIOS 부팅 모드는 표준 BIOS 레벨 부팅 인터페이스입니다. • UEFI 부팅 모드는 시스템 BIOS를 은폐하는 UEFI(Unified Extensible Firmware Interface) 사양에 기반하는 향상된 64비트 부팅 인터페이스입니다. 시스템 부팅 모드를 선택합니다. 1. 시스템 설치 프로그램에서 부팅 설정을 클릭한 후 부팅 모드를 선택합니다. 2. 시스템을 부팅할 부팅 모드를 선택합니다. 노트: 시스템이 지정된 모드에서 부팅된 후, 해당 모드에서 운영 체제를 설치합니다 . 주의: 해당 운영 체제를 다른 부팅 모드에서 부팅하려고 하면 시스템이 시작되는 즉시 정지하게 됩니다. 노트: UEFI 부팅 모드에서 운영 체제를 설치하려면 운영 체제가 UEFI와 호환되어야 합니다.
스페이스바 드롭다운 메뉴(있는 경우)를 확장하거나 축소합니다. 다음 작업 영역으로 이동합니다. 노트: 표준 그래픽 브라우저에만 해당됩니다. 주 화면이 보일 때까지 이전 페이지로 이동합니다. 주 화면에서 를 누르면 저장되 지 않은 변경 내용을 저장하라는 프롬프트 메시지가 나타나고 시스템을 다시 시작합니 다. 시스템 설정 도움말 파일을 표시합니다. 노트: 대부분의 옵션은 변경사항이 기록되었다가 시스템을 재시작해야만 적용됩니 다. 시스템 설치 프로그램 옵션 시스템 설정 기본 화면 노트: BIOS 또는 UEFI 설정을 기본 설정값으로 재지정하려면 를 누릅니다. 메뉴 항목 설명 System BIOS(시스 템 BIOS) 이 옵션은 BIOS 설정을 확인하고 구성하는 데 사용됩니다. iDRAC 설정 이 옵션은 iDRAC 설정을 확인하고 구성하는 데 사용됩니다.
메뉴 항목 설명 Processor Settings(프로세서 설정) 프로세서와 관련된 속도, 캐시 크기 등의 정보 및 옵션을 표시합니다. SATA Settings(SATA 설 정) 내장형 SATA 컨트롤러 및 포트를 활성화하거나 비활성화하는 옵션을 표시합니다. Boot Settings(부팅 설정) 부팅 모드(BIOS 또는 UEFI)를 지정하는 옵션을 표시합니다. UEFI 및 BIOS 부팅 설정을 수정할 수 있습니다. Integrated Devices(내장형 장 치) 내장형 장치 컨트롤러 및 포트를 활성화하거나 비활성화하고 관련 기능 및 옵션을 지정 하는 옵션을 표시합니다. Serial 직렬 포트를 활성화하거나 비활성화하고 관련 기능 및 옵션을 지정하는 옵션을 표시합 Communication(직 니다. 렬 통신) System Profile Settings(시스템 프 로필 설정) 프로세서 전원 관리 설정, 메모리 주파수 등을 변경하는 옵션을 표시합니다.
메뉴 항목 설명 제조업체 연락처 정 보) 메모리 설정 화면 메뉴 항목 설명 System Memory Size(시스템 메모리 크기) 시스템에 설치된 메모리 크기를 표시합니다. System Memory Type(시스템 메모 리 종류) 시스템에 설치된 메모리 종류를 표시합니다. System Memory Speed 시스템 메모리 속도를 표시합니다. System Memory Voltage(시스템 메 모리 전압) 시스템 메모리 전압을 표시합니다. Video Memory 비디오 메모리 크기를 표시합니다. System Memory Testing(시스템 메 모리 검사) 시스템 부팅 중에 시스템 메모리 테스트가 실행되는지 여부를 지정합니다. 옵션으로 Enabled(활성화) 및 Disabled(비활성화)가 있습니다. 기본적으로 System Memory Testing(시스템 메모리 검사) 옵션은 Disabled(비활성화)로 설정됩니다.
프로세서 설정 화면 메뉴 항목 설명 Logical Processor(논리 프 로세서) 논리 프로세서를 활성화하거나 비활성화하고 논리 프로세서의 개수를 표시합니다. Logical Processor(논리 프로세서) 옵션이 Enabled(활성화)로 설정된 경우, BIOS는 모 든 논리 프로세서를 표시합니다. 이 옵션이 Disabled(비활성화)로 설정되어 있으면 BIOS는 논리 프로세서를 코어당 1개만 표시합니다. 기본적으로 Logical Processor(논 리 프로세서) 옵션은 Enabled(활성화)로 설정됩니다. QPI Speed(QPI 속 도) QuickPath Interconnect 데이터 속도 설정값을 지정합니다. 기본적으로 QPI Speed(QPI 속도) 옵션은 Maximum data rate(최대 데이터 속도)로 설정됩니다. 노트: QPI Speed(QPI 속도) 옵션은 프로세서가 2개 설치된 경우에만 표시됩니다.
메뉴 항목 설명 Processor 64-bit Support(프로세서 64비트 지원) 프로세서에서 64비트 확장을 지원하는지 여부를 지정합니다. Processor Core Speed(프로세서 코 어 속도) 프로세서의 최대 코어 주파수를 표시합니다. Processor Bus Speed(프로세서 버 스 속도) 프로세서의 버스 속도를 표시합니다. Processor X Family- ModelStepping(프로세서 X 제품군 모델 스테 핑) 각 프로세서의 제품군 및 모델 번호를 표시합니다. 코어 속도, 캐시 메모리 크기 및 프로 세서의 코어 수가 서브 메뉴에 표시됩니다. 노트: Processor Bus Speed(프로세서 버스 속도) 옵션은 프로세서가 2개 설치된 경우에만 표시됩니다. SATA 설정 화면 메뉴 항목 설명 Embedded 내장형 SATA를 Off(끄기), ATA, AHCI 또는 RAID 모드로 설정할 수 있습니다.
메뉴 항목 설명 Boot Sequence Retry(부팅 순서 재 시도) 부팅 순서 재시도 기능을 활성화하거나 비활성화할 수 있습니다. 이 필드가 활성화되고 시스템이 부팅에 실패하는 경우 시스템은 30초 후에 부팅 순서를 다시 시도합니다. 기 본적으로 Boot Sequence Retry(부팅 순서 재시도) 옵션은 Disabled(비활성화)로 설정 됩니다. BIOS Boot Settings(BIOS 부팅 설정) BIOS 부팅 옵션을 활성화하거나 비활성화할 수 있습니다. UEFI Boot Settings(UEFI 부팅 설정) UEFI 부팅 옵션을 활성화하거나 비활성화할 수 있습니다. 부팅 옵션에는 IPv4 PXE 및 IPv6 PXE가 포함됩니다. 기본적으로 UEFI PXE 부팅 프로토콜은 IPv4로 설정됩니다. 노트: 이 옵션은 부팅 모드가 BIOS인 경우에만 활성화됩니다. 노트: 이 옵션은 부팅 모드가 UEFI인 경우에만 활성화됩니다.
메뉴 항목 설명 OS Watchdog Timer(OS Watchdog 타이머) OS Wacthdog 타이머를 활성화하거나 비활성화할 수 있습니다. 이 필드가 활성화된 경 우 운영 체제에서 타이머가 초기화되고 OS Wacthdog 타이머가 운영 체제 복구를 지 원합니다. 기본적으로 OS Watchdog Timer(OS Watchdog 타이머) 옵션은 Disabled(비활성화)로 설정됩니다. Embedded Video Controller(내장형 비디오 컨트롤러) Embedded Video Controller(내장형 비디오 컨트롤러)를 활성화하거나 비활성화합니 다. 기본적으로 내장형 비디오 컨트롤러는 Enabled(활성화)로 설정됩니다. SR-IOV Global Enable(SR-IOV 글 로벌 활성화) SR-IOV(Single Root I/O Virtualization) 장치의 BIOS 구성을 활성화하거나 비활성화합 니다.
시스템 프로필 설정 화면 메뉴 항목 설명 System Profile(시스 시스템 프로필을 설정합니다. System Profile(시스템 프로필) 옵션을 Custom(사용자 템 프로필) 정의) 이외의 다른 모드로 설정하는 경우, BIOS가 자동으로 나머지 옵션을 설정합니다. 모드가 Custom(사용자 정의)으로 설정된 경우에만 사용자가 나머지 옵션을 변경할 수 있습니다. 기본적으로 System Profile(시스템 프로필) 옵션은 Performance Per Watt Optimized (DAPC)(와트당 성능 최적화(DAPC))로 설정됩니다. DAPC는 Dell Active Power Controller의 약자입니다. 노트: 다음 매개 변수는 System Profile(시스템 프로필)이 Custom(사용자 정의)으 로 설정된 경우에만 사용할 수 있습니다. CPU Power Management(CPU 전원 관리) CPU 전원 관리를 설정합니다.
메뉴 항목 설명 Collaborative CPU Performance Control(공동 작업 CPU 성능 컨트롤) Enabled(활성화)로 설정되면 CPU 전원 관리가 OS DBPM 및 시스템 DBPM (DAPC)에 의해 제어됩니다. 기본적으로 옵션이 Disabled(비활성화)로 설정되어 있습니다. 시스템 보안 화면 메뉴 항목 설명 Intel AES-NI Intel AES-NI 옵션은 고급 암호화 표준 집합을 사용해 암호화 및 암호 해독을 수행하여 응용프로그램의 속도를 향상시키며, 기본적으로 Enabled(활성화)로 설정됩니다. System Password 시스템 암호를 설정합니다. 시스템에 암호 점퍼가 설치되지 않은 경우 이 옵션은 읽기 전용입니다. Setup Password(설 설정 암호를 설정합니다. 시스템에 암호 점퍼가 설치되지 않은 경우 이 옵션은 읽기 전 정 암호) 용입니다. Password Status(암 시스템 암호를 잠급니다.
메뉴 항목 설명 노트: Dell Update Package를 사용하는 BIOS 업데이트는 이 옵션의 영향을 받지 않습니다. 전원 단추 시스템 전면에 있는 전원 단추를 활성화하거나 비활성화합니다. 기본적으로 Power Button(전원 단추) 옵션은 Enabled(활성화)로 설정됩니다. AC Power Recovery(AC 전원 복구) 시스템의 AC 전원이 복구된 후 시스템이 어떻게 반응할지 설정합니다. 기본적으로 AC Power Recovery(AC 전원 복구) 옵션은 Last(마지막)로 설정됩니다. 기타 설정 메뉴 항목 설명 System Time 시스템의 시간을 설정합니다. System Date 시스템의 날짜를 설정합니다. Asset Tag 자산 태그를 표시하며, 보안 및 추적 용도로 자산 태그를 수정할 수 있게 합니다. Keyboard NumLock(키보드 NumLock) 시스템이 부팅할 때 NumLock이 활성화될지 또는 비활성화될지 설정합니다.
노트: 본 시스템은 시스템 및 설정 암호 기능이 비활성화된 상태로 제공됩니다. 시스템 및/또는 설정 암호 지정 노트: 암호 점퍼는 시스템 암호 및 설정 암호 기능을 활성화하거나 비활성화합니다. 암호 점퍼 설정에 대 한 자세한 내용은 "시스템 보드 점퍼 설정"을 참조하십시오. 암호 점퍼 설정이 활성화되어 있고 Password Status(암호 상태)가 Unlocked(잠금 해제)인 경우에만 새 System Password(시스템 암호) 및/또는 Setup Password(설정 암호)를 지정하거나 기존 System Password(시스템 암호) 및/또는 Setup Password(설정 암호)를 변경할 수 있습니다. Password Status(암호 상 태)가 Locked(잠금)이면 시스템 암호 및/또는 설정 암호를 변경할 수 없습니다. 암호 점퍼 설정이 비활성화되어 있고 기존 시스템 암호 및 설정 암호가 삭제된 경우, 시스템을 부팅하기 위해 시스템 암호를 제공하지 않아도 됩니다. 1.
잘못된 시스템 암호를 입력하면 암호를 다시 입력하라는 메시지가 표시됩니다. 올바른 암호를 입력할 수 있는 기회는 세 번입니다. 잘못된 암호를 세 번 입력하면 시스템이 정지되었음을 나타내는 오류 메시지가 표시되며 시스템이 종료됩니다. 시스템을 종료하고 재시작한 후에도 올바른 암호를 입력할 때까지 이 오류 메시지가 계속 표시됩니다. 노트: 시스템이 무단으로 변경되는 것을 방지하려면 System Password(시스템 암호) 및 Setup Password(설정 암호) 옵션과 함께 Password Status(암호 상태) 옵션을 사용할 수 있습니다. 현재 시스템 및/또는 설정 암호를 삭제하거나 변경 기존 시스템 및/또는 설정 암호를 삭제하거나 변경하려면 먼저 암호 점퍼가 '활성화'로 설정되어 있고 Password Status(암호 상태)가 Unlocked(잠금 해제)인지 확인합니다. Password Status(암호 상태)가 Locked(잠금)이면 기존 시스템 또는 설정 암호를 삭제하거나 변경할 수 없습니다.
노트: 시스템 암호가 무단으로 변경되지 않도록 방지하려면 Setup Password(설정 암호) 옵션과 Password Status(암호 상태) 옵션을 함께 사용할 수 있습니다. UEFI 부팅 관리자 시작 노트: UEFI 부팅 모드에서 운영 체제를 설치하려면 해당 운영 체제가 64비트 UEFI 호환 운영 체제(예: Microsoft Windows Server 2008 x64 버전)여야 합니다. DOS 및 32비트 운영 체제는 BIOS 부팅 모드에 서만 설치할 수 있습니다. 이 부팅 관리자를 시작하려면 다음을 수행하십시오. 1. 시스템을 켜거나 재시작합니다. 2. 다음과 같은 메시지가 나타나면 키를 누릅니다. = UEFI Boot Manager 키를 누르기 전에 운영 체제가 로드되기 시작하면 시스템이 부팅을 완료하게 한 다음 시스템을 재 시작하고 다시 시도합니다. 부팅 관리자 탐색 키 사용 키 설명 위쪽 화살표 이전 필드로 이동합니다.
메뉴 항목 설명 UEFI Boot(UEFI 부 팅) 메뉴 사용 가능한 UEFI 부팅 옵션(별표로 표시됨)의 목록을 표시합니다. 사용할 부팅 옵션을 선택하고 키를 누릅니다. UEFI 부팅 메뉴를 통해 Add Boot Option(부팅 옵션 추가), Delete Boot Option(부팅 옵션 삭제) 또는 Boot From File(파일에서 부팅)을 선 택할 수 있습니다. Driver Health Menu(드라이버 상 태) 메뉴 시스템에 설치된 드라이버의 목록 및 해당 드라이버의 상태를 표시합니다. Launch System Setup(시스템 설정 시작) 시스템 설정에 액세스할 수 있습니다. System Utilities(시 스템 유틸리티) BIOS 업데이트 파일 탐색기에 액세스하고, Dell 진단 프로그램을 실행하고, 시스템을 재부팅할 수 있습니다.
iDRAC 설정 유틸리티 시작 1. 관리되는 시스템을 켜거나 재시작합니다. 2. POST(Power-On Self-Test) 중에 키를 누릅니다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 페이지에서 iDRAC Settings(iDRAC 설정)를 클릭합니 다. iDRAC Settings(iDRAC 설정) 화면이 표시됩니다.
3 블레이드 구성부품 설치 권장 도구 이 항목의 절차를 수행하려면 다음 품목이 필요할 수 있습니다. • #1 및 #2 십자 드라이버 • T8 및 T10 별 드라이버 • 손목 접지대 블레이드 분리 및 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 블레이드 분리 1. OS 명령어 또는 CMC를 사용하여 블레이드의 전원을 끈 다음 전원이 꺼졌는지 확인합니다. 블레이드 전원이 꺼지면 전면 패널의 전원 표시등이 꺼집니다. 2. 절반 높이 블레이드 11 또는 12을 분리하기 전에 LCD 화면에 사고로 인한 손상이 발생하지 않도록 LCD 패널을 스토리지 위치로 돌립니다.
그림 3 . 블레이드 분리 또는 설치 1. 블레이드 핸들 2. 분리 단추 3. 블레이드 4. 인클로저의 가이드 레일 5. 블레이드 또는 블레이드 보호물의 가이드 레일 블레이드 설치 1. 새 블레이드를 설치하려면 I/O 커넥터에서 플라스틱 덮개를 분리하여 나중에 사용할 수 있도록 보관합니 다. 2. 핸들이 블레이드 왼쪽에 오도록 블레이드를 놓습니다. 3. 절반 높이 블레이드를 베이 11 또는 12에 설치하려는 경우, LCD 화면에 사고로 인한 손상이 발생하지 않 도록 LCD 모듈을 수평 스토리지 위치로 돌립니다. 4. 8개의 상단 베이 중 하나에 절반 높이 블레이드를 설치하려면 블레이드 상단 가장자리의 가이드 레일을 맞춰 인클로저의 플라스틱 가이드 사이에 들어가게 합니다. 8개의 하단 베이 중 하나에 절반 높이 블레이드를 설치하려면 M1000e 인클로저의 바닥에 있는 가이드 레 일과 블레이드의 가장자리를 맞춥니다. 5.
블레이드 열기 및 닫기 블레이드 열기 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 시스템 내부의 구성요소를 다룰 때는 항상 정전기 방지 매트와 접지대를 사용하는 것이 좋습니다. 1. 인클로저에서 블레이드를 분리합니다. 2. I/O 커넥터 덮개를 설치합니다. 3. 분리 단추를 누르고 덮개를 블레이드 후면 쪽으로 밉니다. 4. 덮개를 블레이드에서 들어올립니다. 그림 4 . 블레이드 열기 및 닫기 1. I/O 커넥터 덮개 2. 블레이드 덮개 3. 분리 단추 4. 덮개 맞춤 핀 및 노치 블레이드 닫기 1.
3. 덮개를 섀시 위에 내려 놓습니다. 4. 딸깍 소리가 나면서 제자리에 고정될 때까지 덮개를 밉니다. 덮개가 올바로 장착되면 섀시 표면과 덮개가 일직선이 됩니다. 블레이드 내부 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 그림 5 . 블레이드 내부 1. 관리 라이저 카드 2. 메자닌 카드 1(선택 사양) - 패브릭 C 3. 메자닌 카드 2(선택 사양) - 패브릭 B 4. 냉각 덮개 5. 프로세서 1 및 방열판 6. 메모리 모듈(B1 - B6) 7. 하드 드라이브/SSD 후면판 8. 하드 드라이브/SSD(2개) 9.
냉각 덮개 냉각 덮개 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 냉각 덮개가 제거된 상태로 시스템을 작동시키지 마십시오. 시스템이 쉽게 가열되어 시스템이 종료 되거나 데이터 손실이 발생할 수 있습니다. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 3. 블레이드 섀시와 가까이 있는 냉각 덮개의 양쪽 끝을 잡고 블레이드에서 냉각 덮개를 들어올립니다. 그림 6 . 냉각 덮개 분리 및 설치 1. 냉각 덮개 3. 섀시의 슬롯(5개) 2.
3. 블레이드를 닫습니다. 4. 블레이드를 인클로저에 설치합니다. 시스템 메모리 이 시스템은 DDR3 UDIMM ECC(Unbuffered ECC DIMM) 및 RDIMM(Registered DIMM)을 지원합니다. 시스 템에서는 DDR3 및 DDR3L 전압 사양을 지원합니다. 노트: MT/s는 DIMM 속도를 초당 메가전송 단위로 나타냅니다. 메모리 버스 작동 주파수는 다음 요인에 따라 1600MT/s, 1333MT/s, 1066MT/s 또는 800MT/s일 수 있습니다.
시스템은 6개 소켓씩 두 집합으로 나뉘는 12개의 메모리 소켓을 가지고 있으며 각 프로세서당 하나의 집합이 할당됩니다. 각각의 6개 소켓 집합은 세 개의 채널로 구성됩니다. 각 채널에서 첫 번째 소켓의 분리 레버는 흰 색으로 표시되고, 두 번째 소켓의 분리 레버는 검정색으로 표시됩니다. 노트: A1-A6 소켓의 DIMM은 프로세서 1에 할당되고 B1-B6 소켓의 DIMM은 프로세서 2에 할당됩니다. 그림 7 . 메모리 소켓 위치 메모리 채널은 다음과 같이 구성됩니다.
• 채널당 최대 2개의 4중 랭크 RDIMM을 장착할 수 있습니다. • 채널당 최대 2개의 단일 또는 이중 랭크 RDIMM을 장착할 수 있습니다. • 채널당 4중 랭크 RDIMM 1개 및 단일 또는 이중 랭크 RDIMM 1개를 장착할 수 있습니다. • 프로세서가 설치된 경우에만 DIMM 소켓을 채우십시오. 단일 프로세서 시스템의 경우 A1-A6 소켓을 사용 할 수 있습니다. 이중 프로세서 시스템의 경우에는 A1-A6 소켓 및 B1-B6 소켓을 사용할 수 있습니다. • 흰색 분리 탭이 있는 모든 소켓을 먼저 채우고 검정색 분리 탭이 있는 소켓을 채웁니다. • 랭크 개수를 기준으로 가장 높은 DIMM부터 흰색 분리 레버가 있는 소켓에 먼저 장착하고 검정잭 분리 레 버가 있는 소켓에 순서대로 장착합니다.
이 모드에서 랭크는 채널당 하나가 스페어로 예약됩니다. 수정 가능한 지속적인 오류가 랭크에서 감지되는 경 우, 이 랭크의 데이터가 스페어 랭크에 복사되고 오류가 발생한 랭크는 비활성화됩니다. 메모리 스페어링이 활성화된 경우, 운영 체제에서 사용 가능한 시스템 메모리는 채널당 랭크 1개씩 줄어듭니 다. 예를 들어, 8GB 이중 랭크 DIMM 3개가 설치된 시스템에서 사용 가능한 시스템 메모리는 24GB(3 (DIMMs) × 8GB)가 아니라 12GB(1/2 (랭크/채널) × 3 (DIMMs) × 8GB)입니다. 노트: 메모리 스페어링은 수정할 수 없는 다중 비트 오류에 대한 보호를 제공하지 않습니다. 노트: 고급 ECC/록스텝 모드 및 옵티마이저 모드는 모두 메모리 스페어링을 지원합니다. 메모리 미러링 메모리 미러링은 다른 모든 모드에 비해 가장 강력한 DIMM 안정성 모드를 제공하여 수정할 수 없는 다중 비트 오류에 대한 보호를 향상시킵니다.
시스템 용량(GB) DIMM 크기 (GB) DIMM 개수 구성 및 속도 DIMM 슬롯 채우기 20 4 5 1R x8, 1333MT/s A1, A2, A3, A4, A5 1R x8, 1600MT/s 24 8 2R x4, 1333MT/s 3 A1, A2, A3 2R x4, 1600MT/s 32 8 2R x4, 1333MT/s 4 A1, A2, A3, A4 2R x4, 1600MT/s 48 16 2R x4, 1333MT/s 3 A1, A2, A3 2R x4, 1600MT/s 96 16 2R x4, 1333MT/s 6 A1, A2, A3, A4, A5, A6 2R x4, 1600MT/s 128 32 4 4R x4, 1066MT/s A1, A2, A3, A4 192 32 6 4R x4, 1066MT/s A1, A2, A3, A4, A5, A6 표 3.
시스템 용량(GB) DIMM 크기(GB) DIMM 개수 구성 및 속도 DIMM 슬롯 채우기 128 16 2R x4, 1333MT/s A1, A2, A3, A4, B1, B2, B3, B4 8 2R x4, 1600MT/s 160 16 10 2R x4, 1333MT/s 2R x4, 1600MT/s 192 16 12 2R x4, 1333MT/s 2R x4, 1600MT/s A1, A2, A3, A4, A5, B1, B2, B3, B4, B5 A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5, B6 256 32 8 4R x4, 1066MT/s A1, A2, A3, A4, B1, B2, B3, B4 384 32 12 4R x4, 1066MT/s A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5, B6 메모리 모듈 분리 경고: 블레이드의 전원을 끈 후에도 한참 동안 DIMM이 뜨거우므로 만지지 마십시오.
그림 8 . 메모리 모듈 또는 메모리 모듈 보호물 설치 및 분리 1. 메모리 모듈 또는 메모리 보호물 2. 에지 커넥터 3. 배출기(2개) 4. 소켓 5. 맞춤 키 메모리 모듈 설치 경고: 메모리 모듈은 시스템 전원을 끈 후에도 얼마 동안 뜨거울 수 있습니다. 메모리 모듈을 다루기 전에 냉각될 때까지 기다리십시오. 메모리 모듈을 다룰 때에는 카드 모서리를 잡고 메모리 모듈의 구성요소 또 는 금속 접촉면을 만지지 않도록 하십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
노트: 메모리 모듈 소켓에는 메모리 모듈을 한 방향으로만 소켓에 설치하도록 하는 맞춤 키가 있습 니다. 7. 엄지손가락으로 메모리 모듈을 눌러 메모리 모듈을 소켓에 고정합니다. 메모리 모듈이 소켓에 올바르게 장착된 경우 메모리 모듈 소켓의 배출기는 메모리 모듈이 설치된 다른 소 켓의 배출기와 맞춰집니다. 8. 나머지 메모리 모듈을 설치하려면 이 절차의 5-7단계를 반복합니다. 9. 냉각 덮개를 설치합니다. 10. 블레이드를 닫습니다. 11. 블레이드를 인클로저에 설치합니다. 12. (선택 사항) 키를 눌러 시스템 설정을 시작하고 System Memory(시스템 메모리) 설정을 확인합니다. 새로 설치된 메모리를 반영하도록 시스템의 설정값이 이미 변경되어 있어야 합니다. 13. 값이 정확하지 않은 경우 하나 이상의 메모리 모듈이 올바르게 설치되지 않았을 수 있습니다. 메모리 모듈 이 해당 소켓에 단단히 장착되었는지 확인합니다. 14.
7. 블레이드를 인클로저에 설치합니다. 그림 9 . 메자닌 카드 분리 및 설치 1. 메자닌 카드(2개) 2. 패브릭 B 메자닌 카드 슬롯 3. 패브릭 C 메자닌 카드 슬롯 4. 고정 래치 메자닌 카드 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 3. 엄지손가락으로 래치의 오톨토돌한 부분을 누르고 래치 끝 부분을 올려 고정 래치를 엽니다. 4. 메자닌 카드 베이에 커넥터 덮개가 있으면 덮개를 분리합니다. 노트: 메자닌 카드의 모서리만 잡습니다.
9. 블레이드를 인클로저에 설치합니다. 관리 라이저 카드 관리 라이저 카드는 내장형 하이퍼바이저 전용 SD 카드 슬롯 2개 및 USB 인터페이스 1개를 제공합니다. 이 카 드에서 제공하는 기능은 다음과 같습니다. • 내부 이중 SD 인터페이스 — 두 슬롯의 SD 카드를 사용하여 미러링되는 구성을 유지하고 중복성을 제공합 니다. • 단일 카드 작동 — 단일 카드 작동이 중복성 없이 지원됩니다. SD 카드 장착 노트: 아래쪽 카드 슬롯에 있는 SD 카드가 기본 카드(SD1)가 되고 위쪽 카드 슬롯에 있는 SD 카드는 보조 카드(SD2)가 됩니다. 1. 시스템 설정을 시작하고 Internal SD Card Port(내부 SD 카드 포트)가 활성화되었는지 확인합니다.
그림 10 . SD 카드 장착 1. SD 카드 1 2. SD 카드 2 3. 관리 라이저 카드 4. USB 커넥터 5. SD 카드 슬롯 식별 레이블 내부 USB 키 이 블레이드에서는 USB 플래시 메모리 키를 위한 내부 USB 커낵터를 제공합니다. USB 메모리 키는 부팅 장 치, 보안 키 또는 대용량 저장 장치로 사용할 수 있습니다. 내부 USB 커넥터를 사용하려면 Internal USB Port(내부 USB 포트) 옵션이 시스템 설정의 Integrated Devices(내장형 장치) 화면에서 활성화되어 있어야 합 니다. USB 메모리 키에서 부팅하려면 부팅 이미지로 USB 메모리 키를 구성한 다음, 시스템 설정의 부팅 순서에서 USB 메모리 키를 지정해야 합니다. USB 메모리 키에 부팅 가능한 파일을 작성하는 방법에 대한 내용은 USB 메모리 키와 함께 제공되는 사용 설명서를 참조하십시오.
5. USB 커넥터에 새 USB 메모리 키를 삽입합니다. 6. 블레이드를 닫습니다. 7. 블레이드를 인클로저에 설치합니다. 8. 시스템 설정을 시작하고 시스템에서 USB 키를 감지했는지 확인합니다. 그림 11 . USB 메모리 키 장착 1. USB 메모리 키 커넥터 2. USB 메모리 키 SD vFlash 카드 SD vFlash 카드 장착 1. 인클로저에서 블레이드를 분리합니다. 2. SD vFlash 카드가 설치되어 있으면 카드 슬롯에서 SD vFlash 카드를 분리합니다. 노트: SD vFlash 카드는 블레이드 뒤쪽의 시스템 보드 아래에 있으며, SD vFlash 카드 슬롯 식별 레 이블로 식별 가능합니다. 3. SD vFlash 카드를 설치하려면 카드 레이블이 위쪽을 향한 상태로 SD 카드의 접촉 핀 끝을 VFlash 매체 장 치의 카드 슬롯에 삽입합니다. 노트: 슬롯은 카드를 올바르게 삽입할 수 있도록 설계되어 있습니다. 4.
그림 12 . SD vFlash 카드 장착 1. SD vFlash 카드 3. SD vFlash 카드 슬롯 식별 레이블 2. SD vFlash 카드 슬롯 프로세서 다음에 해당하는 경우 아래 절차를 사용합니다. • 추가 프로세서 설치 • 프로세서 장착 프로세서 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 경고: 프로세서와 방열판은 매우 뜨거워질 수 있습니다. 프로세서를 취급하기 전에 충분한 시간 동안 냉각되도록 하십시오. 3. 필요하면 냉각 덮개를 분리합니다.
주의: 프로세서를 제거할 의도가 아니라면 프로세서에서 방열판을 제거하지 마십시오. 방열판은 적 절한 열 상태를 유지하는데 필요합니다. 4. 방열판을 블레이드 시스템 보드에 고정시키는 고정 나사를 풉니다. 5. 방열판을 분리합니다. 그림 13 . 방열판 분리 및 설치 6. 1. 고정 소켓(4개) 3. 고정 나사(4개) 2. 방열판 깨끗하고 보풀이 없는 천으로 프로세스 실드 표면의 내열 그리스를 닦아 냅니다. 주의: 강한 힘으로 프로세서를 해당 소켓에 고정해야 합니다. 단단히 잡지 않으면 분리 레버가 갑자 기 튕겨 나올 수 있습니다. 7. 엄지 손가락을 프로세서 소켓 분리 레버 위에 단단히 놓은 후 레버를 잠금 위치에서 분리합니다. 프로세서 가 소켓에서 분리될 때까지 레버를 90도 각도로 위로 돌립니다. 8. 프로세서 실드의 탭을 잡고 실드를 위로 돌려 꺼냅니다. 9. 가능하면 소켓 보호 캡을 프로세서 실드에서 분리합니다.
주의: 소켓 핀은 부러지기 쉽고 영구적으로 손상될 수 있습니다. 프로세서를 소켓에서 분리하는 경 우, 소켓의 핀이 구부러지지 않게 주의하십시오. 10. 프로세서를 소켓에서 들어 꺼내고 분리 레버를 위로 올린 상태로 두어 소켓에 새 프로세서를 설치할 수 있 도록 준비합니다. 주의: 프로세서를 영구적으로 분리하는 경우, 소켓 보호 캡 및 프로세서/DIMM 보호물을 빈 소켓에 설치하여 시스템이 적절히 냉각되도록 해야 합니다. 프로세서/DIMM 보호물은 DIMM 및 프로세서 를 대신하여 빈 소켓을 채웁니다. 그림 14 . 프로세서 분리 및 설치 1. 프로세서 2. 프로세서 실드 3. 프로세서의 노치(2개) 4. 소켓 키(2개) 5. 소켓 분리 레버 프로세서 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다.
4. 가능하면 소켓 보호 캡을 프로세서 실드에서 분리합니다. 소켓 보호 캡을 분리하려면 프로세서 실드 내부 에서 캡을 느르고 소켓 핀에서 캡을 제거합니다. 노트: 프로세서 실드에 소켓 보호 캡을 설치하거나 분리할 때는 프로세서 실드가 열린 상태에서 설 치하거나 분리하는 것이 좋습니다. 주의: 프로세서를 잘못 위치시키면 시스템 보드 또는 프로세서에 영구적인 손상을 입힐 수 있습니다. 소켓의 핀이 구부러지지 않도록 주의하십시오. 주의: 프로세서를 장착하는데 너무 많은 힘을 가하지 마십시오. 프로세서가 올바르게 위치하면 소켓 에 쉽게 장착됩니다. 5. 소켓에 프로세서를 설치합니다. a. 프로세서를 ZIF 소켓의 소켓 키에 맞춥니다. b. 프로세서를 소켓 안에 가볍게 놓습니다. 시스템에서 ZIF 프로세서 소켓을 사용하므로 세게 힘을 가할 필요가 없습니다. 프로세서를 올바르게 정렬한 경우, 힘을 약간만 가해도 프로세서가 소켓에 정확하게 끼워집니다. c. 프로세서 실드를 닫습니다. d.
하드 드라이브/SSD • 이 시스템은 2.5인치 SSD, SAS 또는 SATA 하드 드라이브를 최대 2개까지 지원합니다. • 모든 드라이브는 SAS/SATA/SSD 후면판 보드를 통해 블레이드 시스템 보드에 연결됩니다. • 하드 드라이브/SSD는 해당 드라이브 베이에 맞게 특별 제작된 핫 스왑 가능한 드라이브 캐리어에 담겨 제 공됩니다. • SSD/SAS/SATA 하드 드라이브는 블레이드에서 함께 사용할 수 없습니다. 하드 드라이브/SSD 설치 지침 단일 하드 드라이브 구성의 경우, 냉각 공기가 지속적으로 적절히 흐르도록 다른 드라이브 베이에 하드 드라이 브 보호물이 설치되어야 합니다. 하드 드라이브/SSD 분리 노트: 일부 운영 체제는 핫 스왑 가능 드라이브 설치를 지원하지 않습니다. 운영 체제와 함께 제공되는 설 명서를 참조하십시오. 1.
그림 15 . 하드 드라이브/SSD 분리 및 설치 1. 분리 단추 2. 하드 드라이브/SSD 3. 하드 드라이브/SSD 커넥터(후면판) 4. 하드 드라이브/SSD 캐리어 핸들 하드 드라이브/SSD 설치 주의: 교체용 핫 스왑 가능 하드 드라이브/SSD를 설치하고 블레이드 전원을 켜면 드라이브에서 자동으로 재구축이 시작됩니다. 교체용 하드 드라이브/SSD는 반드시 비어 있거나 덮어쓸 데이터만 포함해야 합니 다. 교체용 하드 드라이브/SSD에 있는 모든 데이터는 드라이브를 설치하는 즉시 지워집니다. 노트: 일부 운영 체제는 핫 스왑 가능 드라이브 설치를 지원하지 않습니다. 운영 체제와 함께 제공되는 설 명서를 참조하십시오. 1. 하드 드라이브/SSD 캐리어 핸들을 엽니다. 2. 하드 드라이브/SSD 캐리어를 드라이브 베이에 삽입합니다. 블레이드의 해당 드라이브 슬롯에 하드 드라 이브/SSD 캐리어의 채널을 조심스럽게 맞춥니다. 3.
부팅 드라이브 구성 시스템이 부팅되는 드라이브 또는 장치는 시스템 설정에서 지정한 부팅 순서에 의해 결정됩니다. 하드 드라이브/SSD 캐리어에서 하드 드라이브/SSD 분리 1. 하드 드라이브/SSD 캐리어의 슬라이드 레일에서 4개의 나사를 분리합니다. 2. 하드 드라이브/SSD 캐리어에서 하드 드라이브/SSD를 들어냅니다. 그림 16 . 하드 드라이브/SSD 캐리어에서 하드 드라이브/SSD 분리 및 설치 1. 하드 드라이브/SSD 2. 나사 구멍(4개) 3. 하드 드라이브/SSD 캐리어 4. 나사(4개) 하드 드라이브/SSD 캐리어에 하드 드라이브/SSD 설치 1. 드라이브의 커넥터 끝이 캐리어의 후면에 놓이도록 하고 하드 드라이브/SSD를 하드 드라이브/SSD 캐리 어 안에 삽입합니다. 2. 캐리어 후면에서 드라이브를 캐리어 안으로 밀어 넣습니다. 3. 하드 드라이브/SSD의 나사 구멍을 하드 드라이브/SSD 캐리어의 구멍에 맞춥니다.
하드 드라이브/SSD 후면판 하드 드라이브/SSD 후면판 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 주의: 하드 드라이브를 동일한 위치에 장착할 수 있도록 분리하기 전에 각 하드 드라이브/SSD의 번 호를 기록하고 임시적으로 레이블을 붙여야 합니다. 주의: 하드 드라이브/SSD 및 하드 드라이브/SSD 후면판의 손상을 방지하려면 하드 드라이브/SSD 후면판을 분리하기 전에 블레이드에서 하드 드라이브/SSD를 분리해야 합니다. 3. 하드 드라이브/SSD를 분리합니다. 4.
그림 17 . 하드 드라이브/SSD 후면판 분리 및 설치 1. 가이드 핀(3개) 2. 가이드(3개) 3. 하드 드라이브/SSD 후면판 4. 하드 드라이브/SSD 커넥터(2개) 5. 하드 드라이브/SSD 후면판 커넥터 하드 드라이브/SSD 후면판 설치 1. 블레이드를 엽니다. 2. 하드 드라이브/SSD 후면판의 가이드를 시스템 보드의 가이드 핀과 맞춥니다. 3. 후면판의 커넥터와 블레이드 시스템 보드가 완전히 맞물릴 때까지 후면판을 아래로 누릅니다. 4. 하드 드라이브/SSD를 기존 위치에 설치합니다. 5. 블레이드를 닫습니다. 6. 블레이드를 인클로저에 설치합니다.
시스템 보드 시스템 보드 제거 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 3. 보드의 후면에 있는 I/O 커넥터에 I/O 커넥터 덮개를 설치합니다. 경고: 프로세서와 방열판은 매우 뜨거워질 수 있습니다. 프로세서를 취급하기 전에 충분한 시간 동안 냉각되도록 하십시오. 경고: 시스템의 전원을 끈 후에도 한참 동안 메모리 모듈이 뜨거우므로 만지지 마십시오. 메모리 모 듈을 다루기 전에 냉각될 때까지 기다립니다. 메모리 모듈을 다룰 때는 카드 모서리를 잡아야 하며 구 성부품을 만지지 마십시오.
그림 18 . 시스템 보드 분리 및 설치 1. I/O 커넥터 덮개 2. 분리 핀 3. 시스템 보드 4. 시스템 섀시의 탭 5. 시스템 보드 트레이 슬롯 시스템 보드 설치 1. 다음 구성부품을 새 시스템 보드로 이동합니다. a. 내부 USB 키 b. 저장소 컨트롤러 카드 c. SD vFlash 카드 d. 메모리 모듈 및 메모리 모듈 보호물 e. 프로세서 및 방열판 또는 프로세서 필러 보호물 주의: 시스템 보드 기판이 섀시와 평행이 되어야 합니다. 2. 새 시스템 보드를 고정 래치가 걸릴 때까지 블레이드 섀시의 열린 쪽으로 밀어 넣습니다. 보드 조립품이 올바르게 설치되면 시스템 보드 팬의 탭이 블레이드 섀시 바닥에 있는 해당 입구에 들어맞 습니다. 3. 메자닌 카드를 기존 위치에 장착합니다. 4. 하드 드라이브/SSD 후면판을 재설치합니다. 5. 하드 드라이브/SSD를 장착합니다. 드라이브가 두 개인 경우, 기존 위치에 다시 설치해야 합니다. 6.
7. 블레이드를 닫습니다. 8. 플라스틱 I/O 커넥터 덮개를 블레이드 후면에서 분리합니다. 9. 블레이드를 인클로저에 설치합니다. 10. 신규 또는 기존 iDRAC Enterprise 라이센스를 가져옵니다. 자세한 내용은 iDRAC7 사용 설명서(dell.com/ support/home)를 참조하십시오. NVRAM 백업 전지 NVRAM 백업 전지 장착 경고: 새 전지를 올바르게 설치하지 않으면 전지가 파열될 위험이 있습니다. 제조업체에서 권장하는 것과 동일하거나 동등한 종류의 전지로만 교체합니다. 다 쓴 전지는 제조업체의 지시에 따라 폐기합니다. 자세 한 내용은 시스템과 함께 제공된 안전 지침을 참조하십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다.
그림 19 . NVRAM 백업 전지 장착 1. 전지의 양극 쪽 2. 전지 커넥터의 음극 쪽 저장소 컨트롤러 카드 시스템의 하드 드라이브에 대한 내장형 저장소 하위 시스템을 제공하는 저장소 컨트롤러 카드를 위한 전용 확 장 카드 슬롯이 블레이드 시스템 보드에 포함되어 있습니다. 저장소 컨트롤러 카드는 SAS 및 SATA 하드 드라 이브를 지원합니다. 노트: 저장소 컨트롤러 카드는 드라이브 베이 아래에 있습니다. 저장소 컨트롤러 카드 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 20 . 저장소 컨트롤러 카드 분리 및 설치 1. 저장소 컨트롤러 카드 2. 나사(2개) 3. 탭(2개) 4. 커넥터 저장소 컨트롤러 카드 설치 1. 저장소 컨트롤러 보호물이 설치되어 있으면 이를 분리합니다. 2. 카드의 모서리를 잡고 카드 커넥터가 시스템 보드 커넥터에 맞춰지도록 저장소 컨트롤러 카드를 놓습니 다. 3. 카드 모서리가 플래스틱 브래킷의 두 탭 아래에 고정되도록 카드의 다른 쪽 끝을 조정합니다. 4. 카드가 완전히 고정될 때까지 컨트롤러 카드 커넥터를 시스템 보드 커넥터에 단단히 끼웁니다. 5. 나사 2개를 장착하여 저장소 컨트롤러 카드를 블레이드 시스템 보드에 고정합니다. 6. 시스템 보드를 재설치합니다. 7. 블레이드를 인클로저에 설치합니다.
4 시스템 문제 해결 안전 제일 — 사용자 및 시스템 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: M1000e 인클로저 구성부품에 대한 문제 해결 정보는 Dell PowerEdge M1000e 인클로저 소유자 설명서(dell.com/support/home)의 "인클로저 문제 해결"을 참조하십시오. 시스템 메모리 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다.
하드 드라이브 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 이 문제 해결 절차로 인해 하드 드라이브에 저장된 데이터가 삭제될 수 있습니다. 계속하기 전에 하 드 드라이브에 있는 모든 파일을 백업합니다(가능한 경우). 1. 시스템 진단 프로그램에서 해당 컨트롤러 검사와 하드 드라이브 검사를 실행합니다. 검사가 실패하면 3단계로 이동합니다. 2. 하드 드라이브를 오프라인으로 전환하고 하드 드라이브 표시등에 드라이브를 제거해도 된다는 드라이버 캐리어 신호가 표시될 때까지 기다린 다음 블레이드에서 드라이브를 제거했다가 다시 장착합니다. 3.
내부 SD 카드 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 설정을 시작하고 Internal SD Card Port(내부 SD 카드 포트)가 활성화되었는지 확인합니다. 2. 시스템 설정의 Integrated Devices(내장형 장치) 화면에서 활성화되어 있는 Internal SD Card Redundancy(내부 SD 카드 중복성) 옵션(Mirror(미러) 또는 Disabled(비활성화))을 확인합니다. 3. 인클로저에서 블레이드를 분리합니다. 4.
블레이드 시스템 보드 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 3. 블레이드 NVRAM을 지웁니다. 4. 블레이드에서 문제가 지속되는 경우 블레이드를 분리했다가 인클로저에 재설치합니다. 5. 블레이드를 켭니다. 6. 적절한 진단 검사를 실행합니다. 자세한 내용은 시스템 진단 프로그램 사용을(를) 참조하십시오 . 검사가 실패하면 도움말 얻기를 참조하십시오. NVRAM 백업 전지 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다.
5 시스템 진단 프로그램 사용 시스템에 문제가 발생하면 기술 지원에 문의하기 전에 시스템 진단 프로그램을 실행합니다. 진단 프로그램은 추가 장비 없이 또는 데이터를 유실할 위험 없이 시스템 하드웨어를 검사하기 위해 실행됩니다. 자체적으로 문 제를 해결할 수 없는 경우에는 서비스 및 지원 담당 직원이 진단 검사 결과를 사용하여 문제 해결을 지원할 수 있습니다. Dell 내장형 시스템 진단 프로그램 노트: Dell 내장형 시스템 진단 프로그램은 ePSA(Enhanced Pre-boot System Assessment) 진단 프로그 램이라고도 합니다. 내장형 시스템 진단 프로그램은 특정 장치 그룹 또는 장치에 대해 일련의 옵션을 제공하여 사용자가 다음을 수 행할 수 있게 합니다. • 자동으로 테스트 또는 상호 작용 모드를 실행합니다. • 테스트를 반복합니다. • 테스트 결과를 표시 또는 저장합니다.
시스템 진단 제어 메뉴 설명 구성 감지된 모든 장치의 구성 및 상태 정보를 표시합니다. Results(결과) 실행된 모든 검사의 결과를 표시합니다. System Health(시 스템 상태) 시스템 상태에 대한 현 시점의 개요를 제공합니다. Event log(이벤트 로그) 시스템에서 실행된 모든 테스트의 결과를 타임스탬프와 함께 보여 주는 로그를 표시합 니다. 이벤트 설명이 하나 이상 기록되어 있으면 이 로그가 표시됩니다. 내장형 시스템 진단 프로그램에 대한 자세한 정보를 보려면 dell.com/support/home의 ePSA 진단 설명서(노 트북, 데스크탑 및 서버)를 참조하십시오.
6 점퍼 및 커넥터 시스템 보드 점퍼 설정 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 암호 점퍼를 재설정하여 암호를 비활성화하는 방법에 대한 자세한 내용은 잊은 암호 비활성화를 참조하십시 오. 표 4. 시스템 보드 점퍼 설정 점퍼 PWRD_EN 설정 설명 (기본값) 암호 기능이 활성화됩니다. 암호 기능이 비활성화됩니다. NVRAM_CLR (기본값) 구성 설정이 시스템 부팅 시 유지됩니다. 다음 시스템 부팅 시 구성 설정이 지워집니다. 구성 설정 이 손상되어 시스템이 부팅되지 않는 경우에는 점퍼를 설 치하고 시스템을 부팅합니다.
시스템 보드 커넥터 그림 21 . 시스템 보드 커넥터 표 5. 시스템 보드 커넥터 항목 커넥터 설명 1 PWRD_EN, NVRAM_CLR 시스템 구성 점퍼 2 CPU2 프로세서 소켓 2 3 A1, A4, A2, A5, A3, A6 메모리 모듈 소켓(프로세서 1) 4 관리 라이저 관리 라이저 카드 커넥터 5 MEZZ1_FAB_C 메자닌 카드 커넥터(패브릭 C용) 6 MEZZ2_FAB_B 메자닌 카드 커넥터(패브릭 B용) 7 - SD vFlash 카드 커넥터 노트: SD vFlash 카드 커넥터는 시스템 보드 아래에 있습니다.
항목 커넥터 설명 13 USB1 USB 커넥터 14 전지 3.0V 코인 셀 전지용 커넥터 잊은 암호 비활성화 블레이드의 소프트웨어 보안 기능에는 시스템 암호 및 설정 암호가 포함됩니다. 암호 점퍼를 사용하면 이러한 암호 기능을 활성화 또는 비활성화할 수 있고 현재 사용되는 암호를 지울 수 있습니다. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직 접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 인클로저에서 블레이드를 분리합니다. 2. 블레이드를 엽니다. 3. 시스템 보드를 분리하여 점퍼에 접근합니다. 4. 점퍼 플러그를 재배치하여 암호 기능을 비활성화합니다. 5. 시스템 보드를 재설치합니다. 6.
7 기술 사양 프로세서 Intel Xeon 프로세서 E5-2400 제품군 1개 또는 2개 프로세서 종류 Intel Xeon 프로세서 E5-2400v2 제품군 1개 또는 2 개 메모리 아키텍처 1600MT/s, 1333MT/s, 1066MT/s 또는 800MT/s DDR3 및 LV-DDR3 DIMM 메모리 모듈 소켓 240핀 12개 메모리 모듈 용량 RDIMM 2GB(단일 랭크), 4GB(단일 및 이중 랭크), 8GB(이중 랭크), 16GB(이중 랭크) 및 32GB(4중 랭크) UDIMM 2GB(단일 랭크) 및 4GB(이중 랭크) 최소 RAM 2GB(단일 프로세서 구성) 최대 RAM 384GB Drives 하드 드라이브 2.5인치 핫 플러그 가능 SSD/SAS/SATA 하드 드라이 브 최대 2개 광학 드라이브 외장형 USB DVD(선택 사양) 노트: DVD 장치는 데이터 전용입니다.
커넥터 SD 하이퍼바이저 전용 내장형 SD 카드 2개 1개는 향후 vFlash 지원 전용 메자닌 카드 메자닌 슬롯 이중 포트 Gb 이더넷, 10Gb 이더넷, FC8 파이버 채 널 또는 Infiniband 메자닌 카드를 지원하는 메자닌 PCIe x8 Gen 3 슬롯 2개 동영상 비디오 종류 Matrox G200, iDRAC와 통합 비디오 메모리 8MB(iDRAC 응용프로그램 메모리와 공유) 전지 NVRAM 백업 전지 CR 2032 3.0V 리튬 코인 셀 환경적 특성 노트: 특정 시스템 구성을 위한 환경 측정에 대한 추가 정보는 dell.com/environmental_datasheets를 참조하십시오. 보관 온도 –40°C ~ 65°C(–40°F ~ 149°F), 시간당 최고 20°C의 온도 변화 기준 표준 작동 온도 연속 작동: 10% - 80% 상대 습도(RH)에서 10°C 35°C, 최대 이슬점은 26°C입니다.
환경적 특성 연간 작동 시간의 ≤ 1% RH 5% ~ 90%에서 -5°C ~ 45°C, 이슬점 26°C 노트: 표준 작동 온도(10°C ~ 35°C) 범위를 벗어 나는 경우 연간 작동 시간의 최대 1% 동안 -5°C 또는 45°C까지에서 시스템을 작동할 수 있습니 다. 온도가 40°C - 45°C인 경우 허용되는 최대 건구 온 도는 950m를 넘는 고도에서 1°C/125m(1°F/228ft)로 감소합니다.
8 시스템 메시지 LCD 상태 메시지 LCD 메시지는 SEL(시스템 이벤트 로그)에 기록된 이벤트를 참조하는 간단한 텍스트 메시지로 구성되어 있습 니다. SEL 및 시스템 관리 설정 구성에 대한 자세한 내용은 시스템 관리 소프트웨어 설명서를 참조하십시오. LCD 메시지 보기 시스템 오류가 발생하면 LCD 화면이 황색으로 바뀝니다. 오류나 상태 메시지의 목록을 보려면 Select(선택) 단추를 누르십시오. 왼쪽 및 오른쪽 단추를 사용하여 오류 번호를 강조 표시하고 Select(선택)를 눌러 오류를 확인할 수 있습니다. LCD 메시지 제거 센서와 관련된 오류(예: 온도, 전압, 팬 등)일 경우 센서가 정상 상태로 회복되면 LCD 메시지는 자동으로 제거 됩니다. 다른 오류일 경우 메시지를 디스플레이에서 제거하기 위한 작업을 수행해야 합니다. • SEL 지우기 — 이 작업을 원격으로 수행할 수 있지만 시스템의 이벤트 기록은 유실됩니다.
오류 코드 메시지 정보 조치 AMP0301 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. LCD 메시지 System board current is outside of range(시스템 보 드 의 전류가 범위를 벗어납니다). 상세 정보 시스템 보드 의 전류가 최적 범위를 벗어납니다. 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The system board current is greater than the upper warning threshold(시스템 보드 의 전류가 경고 임계값 상한보다 높습니다). 상세 정보 시스템 보드 의 전류가 최적 범위를 벗어납니다. 1.
오류 코드 메시지 정보 4. AMP0304 메시지 The system board current is outside of range(시스템 보드 의 전류가 범위를 벗어납니다). LCD 메시지 System board current is outside of range(시스템 보 드 의 전류가 범위를 벗어납니다). 상세 정보 시스템 보드 의 전류가 최적 범위를 벗어납니다. 조치 AMP0306 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Disk drive bay current is less than the lower warning threshold(디스크 드라이브 베이 의 전류가 경고 임계 값 하한보다 낮습니다).
오류 코드 AMP0308 메시지 정보 메시지 Disk drive bay current is greater than the upper warning threshold(디스크 드라이브 베이 의 전류가 경 고 임계값 상한보다 높습니다). 상세 정보 디스크 드라이브 베이 의 전류가 최적 범위를 벗어납니 다. 조치 AMP0309 72 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. Disk drive bay current is greater than the upper critical threshold(디스크 드라이브 베이 의 전류가 중 대 임계값 상한보다 높습니다). LCD 메시지 Disk drive bay current is outside of range(디스크 드 라이브 베이 의 전류가 범위를 벗어납니다).
오류 코드 메시지 정보 상세 정보 조치 AMP0313 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. System level current is less than the lower warning threshold(시스템 레벨 전류가 경고 임계값 하한보다 낮습니다). LCD 메시지 System level current is outside of range(시스템 레벨 전류가 범위를 벗어납니다). 상세 정보 시스템 레벨 전류가 최적 범위를 벗어납니다. 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 AMP0316 메시지 정보 메시지 System level current is outside of range(시스템 레벨 전류가 범위를 벗어납니다). LCD 메시지 System level current is outside of range(시스템 레벨 전류가 범위를 벗어납니다). 상세 정보 시스템 레벨 전류가 최적 범위를 벗어납니다. 조치 AMP0318 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. 상세 정보 섀시 전원 레벨 전류가 최적 범위를 벗어납니다. 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 AMP0321 메시지 정보 ASR0001 4. 문제가 계속되면 도움말 얻기를 참조하십시오. Chassis power level current is greater than the upper critical threshold(섀시 전원 레벨 전류가 중대 임계값 상한보다 높습니 다). 상세 정보 섀시 전원 레벨 전류가 최적 범위를 벗어납니다. 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Chassis power level current is outside of range(섀시 전원 레 벨 전류가 범위를 벗어납니다). 상세 정보 섀시 전원 레벨 전류가 최적 범위를 벗어납니다. 조치 ASR0000 시스템 구성 변경 사항을 검토합니다. 메시지 조치 AMP0322 3. 1. 시스템 전원 정책을 검토합니다. 2.
오류 코드 ASR0002 ASR0003 ASR0008 ASR0100 ASR0101 ASR0102 76 메시지 정보 메시지 The watchdog timer powered off the system(Watchdog 타이 머가 시스템 전원을 껐습니다). 상세 정보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 시스템이 종료되었습니다. 조치 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다. 메시지 The watchdog timer power cycled the system(Watchdog 타 이머가 시스템 전원을 껐다가 켰습니다). 상세 정보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 시스템 전원이 꺼졌다가 켜졌습니다. 조치 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다.
오류 코드 ASR0103 ASR0104 ASR0105 ASR0106 ASR0107 메시지 정보 상세 정보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 시스템이 종료되었습니다. 조치 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다. 메시지 The OS watchdog timer powered down the system(OS Watchdog 타이머가 시스템 전원을 껐습니다). 상세 정보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 시스템 전원이 꺼졌습니다. 조치 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다. 메시지 The OS watchdog timer power-cycled the system(OS Watchdog 타이머가 시스템 전원을 껐다가 켰습니다).
오류 코드 BAT0000 BAT0002 BAT0004 BAT0005 BAT0007 78 메시지 정보 상세 정보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 조치 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다. 메시지 The system board battery is low(시스템 보드 전지가 많이 소모 되었습니다). 상세 정보 시스템 보드 전지가 없거나 불량이거나 발열 문제로 인해 충전 될 수 없습니다. 조치 시스템 팬을 점검합니다. 시스템 보드 전지를 교체하십시오. 메시지 The system board battery has failed(시스템 보드 전지에 오류 가 발생했습니다). LCD 메시지 The system board battery has failed. Check battery(시스템 보 드 전지에 오류가 발생했습니다. 전지를 점검하십시오).
오류 코드 BAT0010 BAT0012 BAT0014 BAT0015 BAT0017 메시지 정보 메시지 The storage battery for disk drive bay is low(디스크 드 라이브 베이 의 축전지가 많이 소모되었습니다). 상세 정보 축전지를 충전하려면 시스템이 계속 켜져 있어야 합니다. 조치 축전지가 충전되도록 합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The storage battery for disk drive bay has failed(디스크 드라이브 베이 의 축전지에 오류가 발생했습니다). LCD 메시지 Battery for disk drive bay has failed. Check battery(디 스크 드라이브 베이 의 전지에 오류가 발생했습니다. 전지 를 점검하십시오). 상세 정보 축전지와 컨트롤러 간 케이블 연결을 확인합니다. 조치 축전지 설치를 확인하십시오.
오류 코드 BAT0019 CBL0006 CPU0000 CPU0001 CPU0002 80 메시지 정보 메시지 The battery is absent( 전지가 없습니다). LCD 메시지 The battery is absent. Check battery( 전지가 없습니다. 전지를 점검하십시오). 상세 정보 전지에 오류가 발생하거나 전지가 없으면 시스템 성능 이 저하될 수 있습니다. 조치 시스템 팬을 점검합니다. 전지를 교체하십시오. 메시지 Multiple storage controllers are incorrectly connected to the same backplane (여러 개의 저장소 컨트롤러가 동일 한 후면판 에 잘못 연결되어 있습니다). 상세 정보 지원되지 않는 후면판 구성입니다. 조치 후면판 구성을 점검합니다. 문제가 계속되면 도움말 얻기를 참 조하십시오.
오류 코드 메시지 정보 조치 CPU0003 메시지 조치 CPU0004 메시지 조치 CPU0005 CPU0006 1. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 입력 전 원을 다시 넣어 시스템을 켭니다. 2. 프로세서가 올바르게 장착되었는지 확인합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. CPU is stuck in POST(CPU 이(가) POST 에서 벗어나지 못합니다). 1. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 입력 전 원을 다시 넣어 시스템을 켭니다. 2. 시스템 구성의 메모리를 최소 수준으로 줄이고 모든 PCI 장치를 분리합니다. 시스템이 POST를 완료하면 시스템 BIOS를 업데이트합니다. 메모리 및 PCI 구성부품을 동시 에 재설치하여 원래 구성을 충족시킵니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 조치 CPU0008 CPU0010 CPU0023 CPU0100 CPU0101 82 1. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 입력 전 원을 다시 넣어 시스템을 켭니다. 2. 프로세서가 올바르게 장착되었는지 확인합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 CPU is disabled(CPU 이(가) 비활성화되 어 있습니다). 상세 정보 시스템이 부팅하지 못하거나 성능이 저하된 상태로 실행될 수 있습니다. 조치 예기치 않은 메시지가 표시되면 해당 CPU가 있는지 점검하고 시스템 설정(BIOS) 구성을 확인하십시오. 메시지 CPU is throttled(CPU 사용률이 조절되 고 있습니다). 상세 정보 온도 또는 전원 상태로 인해 CPU 사용률이 조절되고 있습니다. 조치 시스템 로그를 검토하여 전원 또는 온도 예외가 있는지 확인합 니다.
오류 코드 CPU0102 CPU0103 CPU0104 CPU0200 메시지 정보 조치 시스템 작동 환경, 팬 및 방열판을 점검하십시오. 메시지 CPU temperature is greater than the upper warning threshold(CPU 온도가 경고 임계값 상한보 다 높습니다). 상세 정보 시스템 성능이 저하될 수 있습니다. 조치 시스템 작동 환경, 팬 및 방열판을 점검하십시오. 메시지 CPU temperature is greater than the upper critical threshold(CPU 온도가 중대 임계값 상한보다 높습 니다). LCD 메시지 CPU temperature is outside of range. Check fans(CPU 온도가 범위를 벗어납니다. 팬을 점검하십 시오). 상세 정보 시스템 성능이 저하될 수 있습니다.
오류 코드 CPU0201 메시지 정보 메시지 CPU voltage is less than the lower critical threshold(CPU 전압이 중대 임계값 하한보 다 낮습니다). LCD 메시지 CPU voltage is outside of range. Re-seat CPU(CPU 전압이 범위를 벗어납니다. CPU 를 다시 장착하십시오). 상세 정보 전압이 낮으면 전압 조정기 또는 프로세서에 문제가 있기 때문 일 수 있습니다. 중대 임계값을 초과하면 프로세서가 작동하지 못하게 됩니다. 시스템 전원이 꺼질 수도 있습니다. 조치 CPU0202 2. 입력 전원을 다시 넣어 시스템을 켭니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 CPU0204 메시지 정보 4. 문제가 계속되면 도움말 얻기를 참조하십시오. CPU voltage is outside of range(CPU 전압이 범위를 벗어납니다). LCD 메시지 CPU voltage is outside of range. Re-seat CPU(CPU 전압이 범위를 벗어납니다. CPU 를 다시 장착하십시오). 상세 정보 전압이 허용 범위를 벗어나면 전기적 구성부품이 손상되거나 시 스템이 종료될 수 있습니다. 1. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 2. 프로세서가 올바르게 장착되었는지 확인합니다. 3. 입력 전원을 다시 넣어 시스템을 켭니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 CPU0702 메시지 정보 86 4. 입력 전원을 다시 넣어 시스템을 켭니다. 5. 문제가 계속되면 도움말 얻기를 참조하십시오. CPU bus parity error detected(CPU 버스 패리티 오류가 감지 되었습니다). LCD 메시지 CPU bus parity error detected. Power cycle system(CPU 버스 패리티 오류가 감지되었습니다. 시스템 전원을 껐다가 켜십시 오). 상세 정보 시스템 이벤트 로그 및 운영 체제 로그에서는 예외가 프로세서 외부에 있다고 기록될 수 있습니다. 1. 시스템 및 운영 체제 로그에서 예외를 확인합니다. 예외가 발견되지 않으면 다음을 계속하십시오. 2. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 입력 전원을 다시 넣어 시스템을 켭니다. 5. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 상세 정보 조치 CPU0801 시스템 및 운영 체제 로그에서 예외를 확인합니다. 예외가 발견되지 않으면 다음을 계속하십시오. 2. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 입력 전원을 다시 넣어 시스템을 켭니다. 5. 문제가 계속되면 도움말 얻기를 참조하십시오. CPU voltage regulator module failed(CPU 전압 조정기 모듈에 오류가 발생했습니다). LCD 메시지 CPU voltage regulator module failed. Re-seat module(CPU 전압 조정기 모듈에 오류가 발생했습 니다. 모듈을 다시 장착하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 1. 시스템을 끄고 입력 전원을 1분 동안 분리합니다. 2.
오류 코드 메시지 정보 LCD 메시지 Lost power input for CPU voltage regulator module. Re-seat module(CPU 전압 조정기 모듈의 전원 입력이 손실되었습니다. 모듈을 다시 장착하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 CPU0804 2. 입력 전원을 다시 넣어 시스템을 켭니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. The power input for CPU voltage regulator module is outside of range(CPU 전압 조정기 모듈 의 전원 입력이 범위를 벗어납니다). LCD 메시지 The power input for CPU voltage regulator module is outside of range.
오류 코드 CPU0806 CPU0816 HWC1001 HWC1002 HWC1005 메시지 정보 메시지 CPU voltage regulator module is incorrectly configured(CPU 전압 조정기 모듈이 잘못 구성되어 있습니다). LCD 메시지 CPU voltage regulator module incorrectly configured. Check configuration(CPU 전압 조정기 모듈이 잘못 구성되어 있습니다. 구성을 점검하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 이 설명서를 검토하여 적절한 구성 및 설치 절차를 확인하십시 오. 메시지 CPU voltage regulator module is absent(CPU 전압 조정기 모듈이 없습니다).
오류 코드 HWC1006 HWC1009 HWC1010 HWC1015 HWC2006 HWC2008 90 메시지 정보 조치 저장 장치 어댑터를 설치하십시오. 메시지 The storage adapter is disabled(저장 장치 어댑터가 비활성화 되어 있습니다). 조치 저장 장치 어댑터가 예기치 않게 비활성화된 경우, 어댑터를 다 시 활성화하십시오. 메시지 The backplane is absent(후면판이 없습니다). LCD 메시지 The backplane is absent. Check hardware(후면판이 없습니다. 하드웨어를 점검하십시오). 상세 정보 올바른 작동을 위해서는 후면판이 필요할 수 있습니다. 시스템 기능이 저하될 수도 있습니다. 조치 제거할 의도가 없었다면 후면판이 있는지 확인한 후, 다시 설치 하거나 다시 연결하십시오. 메시지 The backplane is disabled(후면판이 비활성화되어 있습니다).
오류 코드 HWC2011 HWC3000 HWC3002 HWC3004 HWC4000 메시지 정보 상세 정보 IOM 및 메자닌 카드에 대한 패브릭 유형이 일치해야 합니다. 조치 CMC GUI에서 섀시 패브릭 유형을 확인하고 IOM 또는 메자닌 카드의 유형과 비교하십시오. 메시지 The riser board cable or interconnect is not connected, or is improperly connected(라이저 보드 케이블 또는 인터커넥트가 연결되어 있지 않거나 잘못 연결되어 있습니다). LCD 메시지 Riser board cable or interconnect failure. Check connection(라이저 보드 케이블 또는 인터커넥트에 오류가 있 습니다. 연결을 점검하십시오). 상세 정보 올바른 작동을 위해서는 라이저 보드 케이블이 필요할 수 있습 니다. 시스템 기능이 저하될 수도 있습니다.
오류 코드 HWC4002 HWC4011 HWC4013 HWC4015 HWC5001 92 메시지 정보 상세 정보 BMC/iDRAC 펌웨어와 프로세서 간에 하드웨어 비호환성이 감 지되었습니다. iDRAC 또는 BMC 펌웨어 업데이트가 필요합니 다. 조치 BMC/iDRAC 펌웨어를 업데이트합니다. 문제가 계속되면 도움 말 얻기를 참조하십시오. 메시지 A hardware incompatibility detected between BMC/iDRAC firmware and other hardware(BMC/iDRAC 펌웨어와 다른 하 드웨어 간에 하드웨어 비호환성이 감지되었습니다). 상세 정보 BMC/iDRAC 펌웨어와 다른 하드웨어 간에 하드웨어 비호환성 이 감지되었습니다. iDRAC 또는 BMC 펌웨어 업데이트가 필요 합니다. 조치 BMC/iDRAC 펌웨어를 업데이트합니다. 문제가 계속되면 도움 말 얻기를 참조하십시오.
오류 코드 HWC5002 HWC5004 HWC5006 HWC5008 HWC5010 HWC5014 HWC5031 HWC5032 메시지 정보 메시지 A fabric mismatch detected on (에서 패브릭 불일치가 감지되었습니다). 상세 정보 IOM 및 메자닌 카드에 대한 패브릭 유형이 일치해야 합니다. 조치 CMC GUI에서 섀시 패브릭 유형을 확인하고 IOM 또는 메자닌 카드의 유형과 비교하십시오. 메시지 A link tuning failure detected on (에서 링크 튜닝 오류가 감지되었습니다). 상세 정보 CMC의 펌웨어가 오래되었습니다. 펌웨어를 업데이트하면 CMC가 장치를 인식하게 됩니다. 조치 CMC 펌웨어를 업데이트합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 A failure is detected on (에서 오류가 감지되 었습니다).
오류 코드 HWC5034 HWC5036 HWC6000 HWC6002 HWC6003 HWC6004 94 메시지 정보 상세 정보 동일한 섀시 패브릭에서 IOM에 대한 패브릭 유형이 서로 일치 해야 합니다. 조치 CMC GUI에서 섀시 패브릭 유형을 확인하고 두 IOM의 유형과 비교하십시오. 메시지 A link tuning failure detected on IO module (IO 모 듈 에서 링크 튜닝 오류가 감지되었습니다). 상세 정보 이 IO 모듈에 대해 링크 튜닝 테이블이 지원되지 않습니다. 조치 CMC 펌웨어를 업데이트합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 A failure is detected on IO module (IO 모듈 에서 오류가 감지되었습니다). 상세 정보 IOM 모듈 성능에 영향을 줄 수 있습니다. 조치 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 HWC7002 HWC7004 HWC7006 HWC7008 HWC7010 메시지 정보 메시지 Server health changed to a warning state from a normal state(서버 의 상태가 정상 상태에서 경고 상 태로 변경되었습니다). 상세 정보 서버 의 상태가 정상 상태에서 경고 상태로 변경되었 습니다. 조치 시스템 로그 또는 전면 패널에서 추가적인 정보를 찾으십시오. 메시지 Server health changed to a critical state from either a normal or warning state(서버 의 상태가 정 상 또는 경고 상태에서 중대 상태로 변경되었습니다). 상세 정보 서버 의 상태가 정상 상태에서 경고 상태로 변경되었 습니다. 조치 시스템 로그 또는 전면 패널에서 추가적인 정보를 찾으십시오.
오류 코드 HWC7012 LNK2700 MEM0000 MEM0001 MEM0002 96 메시지 정보 메시지 Server health changed to a nonrecoverable state(서버 의 상태가 복구할 수 없는 상태로 변경되 었습니다). 상세 정보 서버 의 상태가 정상 상태에서 경고 상태로 변경되었 습니다. 조치 시스템 로그 또는 전면 패널에서 추가적인 정보를 찾으십시오. 메시지 The LAN heartbeat is lost( LAN 하트비트가 손실되었습니다). 상세 정보 CMC의 네트워크 연결이 손실되었습니다. 조치 네트워크 케이블 및 네트워크 연결을 점검하십시오.
오류 코드 MEM0003 MEM0004 MEM0005 MEM0007 메시지 정보 조치 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 Stuck bit memory error detected on a memory device at location (스턱(Stuck) 비트 메모리 오류가 위치에 있는 메모리 장치에서 감지되었습니다). 상세 정보 이 메시지는 복구할 수 없는 오류가 향후에 발생할 수 있음을 미 리 알려 줍니다. 조치 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 Memory device at location is disabled( 위치에 있는 메모리 장치가 비활성화되어 있습니다). 상세 정보 메모리가 잘못 장착되어 있거나 잘못 구성되어 있거나 메모리에 오류가 있을 수 있습니다. 메모리 크기가 줄어듭니다.
오류 코드 MEM0009 MEM0010 MEM0022 MEM0701 MEM0702 98 메시지 정보 조치 메모리 구성을 점검합니다. 메모리 모듈을 다시 장착합니다. 문 제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Memory device at location is throttled( 위치에 있는 메모리 장치의 사용률이 조절됩니다). 상세 정보 시스템 성능이 저하됩니다. 조치 예기치 않게 메시지가 표시되면 시스템 로그를 검토하여 전원 또는 온도 예외가 있는지 확인합니다. 메시지 Memory device at location is over heating( 위치에 있는 메모리 장치가 과열되고 있습 니다). LCD 메시지 Memory device is over heating. Check fans( 위치에 있는 메모리 장치가 과열되고 있습니다. 팬을 점검하십시오).
오류 코드 MEM1001 MEM1003 MEM1012 MEM1016 메시지 정보 LCD 메시지 Correctable memory error rate exceeded for . Reseat memory(수정 가능한 메모리 오류 비율이 에 대 해 초과되었습니다. 메모리를 다시 장착하십시오). 상세 정보 메모리가 작동하지 않을 수 있습니다. 이 메시지는 복구할 수 없 는 오류가 향후에 발생할 수 있음을 미리 알려 줍니다. 조치 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 Memory device at location failed to transition to a running state( 위치에 있는 메모리 장치가 실행 중 상태로 전이되지 못했습니다).
오류 코드 MEM1205 MEM1206 MEM1208 MEM1212 100 메시지 정보 LCD 메시지 Memory is not installed correctly. Reinstall( 위치에 있는 메모리가 올바르게 설치되어 있지 않습니다. 다시 설치하십시오). 상세 정보 메모리가 잘못 장착되어 있거나 잘못 구성되어 있거나 메모리에 오류가 있을 수 있습니다. 메모리 크기가 줄어듭니다. 조치 메모리 구성을 점검합니다. 메모리 모듈을 다시 장착합니다. 문 제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Memory mirror redundancy is lost. Check memory device at location(s) (메모리 미러 중복성이 손실되었습니다. 위치에 있는 메모리 장치를 점검하십시오). LCD 메시지 Memory mirror lost on .
오류 코드 MEM1214 MEM7002 MEM8000 OSE0000 메시지 정보 상세 정보 메모리가 잘못 장착되어 있거나 잘못 구성되어 있거나 메모리에 오류가 있을 수 있습니다. 조치 시스템 로그를 검토하여 메모리 예외가 있는지 확인합니다. 위치에 메모리를 다시 설치하십시오. 메시지 Memory redundancy is degraded(메모리 중복성이 저하되었습 니다). 상세 정보 메모리가 잘못 장착되어 있거나 잘못 구성되어 있거나 메모리에 오류가 있을 수 있습니다. 조치 메모리 구성을 점검합니다. 메모리 모듈을 다시 장착합니다. 문 제가 계속되면 도움말 얻기를 참조하십시오. 메시지 A hardware mismatch detected for memory riser(메모리 라이 저에 대해 하드웨어 불일치가 감지되었습니다). LCD 메시지 Memory riser mismatch detected.
오류 코드 OSE0001 OSE0004 OSE0005 OSE1001 OSE1003 OSE1005 102 메시지 정보 조치 운영 체제 로그 및 시스템 비디오를 검토하여 추가적인 정보를 찾으십시오. 메시지 A runtime critical stop occurred(런타임에 치명적인 중지가 발 생했습니다). 상세 정보 운영 체제 실행 중에 예외로 인해 시스템이 중지되었습니다. 이 는 커널 패닉 또는 버그 체크 이벤트입니다. 조치 운영 체제 로그 및 시스템 비디오를 검토하여 추가적인 정보를 찾으십시오. 메시지 A soft shut-down initiated by platform event filter(플랫폼 이 벤트 필터에 의해 소프트 종료가 시작되었습니다). 상세 정보 개별적인 예외 또는 상태 조건으로 인해 운영 체제가 종료되었 습니다(IPMI 센서 유형 20h - 오프셋 04h).
오류 코드 OSE1007 OSE1009 OSE1011 OSE1013 PCI1302 PCI1304 PCI1306 메시지 정보 메시지 Diagnostic boot failed(진단 부팅이 실패했습니다). 조치 시스템 부팅 구성 및 부팅 미디어를 검토합니다. 추가적인 정보 는 시스템 비디오를 참조하십시오. 메시지 Failed to boot from CD-ROM(CD-ROM에서 부팅하지 못했습 니다). 조치 시스템 부팅 구성 및 부팅 미디어를 검토합니다. CDROM의 미 디어가 부팅 가능한지 확인합니다. 추가적인 정보는 시스템 비 디오를 참조하십시오. 메시지 Failed to boot from ROM(ROM에서 부팅하지 못했습니다). 조치 시스템 이벤트 로그에서 추가적인 예외 정보를 확인합니다. 시 스템 전원을 끄고 다시 부팅을 시도하십시오. 메시지 Failed to boot(부팅하지 못했습니다). 조치 시스템 부팅 구성 및 부팅 미디어를 검토합니다.
오류 코드 메시지 정보 기능 에 있는 구성부품에서 소프트웨어 오류가 감지되었습니다). PCI1308 PCI1310 PCI1314 PCI1316 104 조치 시스템을 재부팅하고 구성부품 드라이버를 업데이트하십시오. 메시지 A PCI parity error was detected on a component at bus devicefunction (버스 장치 기능 에 있는 구성부품에서 PCI 패리티 오류가 감지되었습니다). LCD 메시지 PCI parity error on bus device function . Power cycle system(버스 장치 기능 에서 PCI 패리티 오류가 감지되었습니다. 시스템 전원을 껐다가 켜십시오). 상세 정보 시스템 성능이 저하될 수 있습니다.
오류 코드 메시지 정보 기능 에 있는 구성부품에서 수정할 수 없는 버 스 오류가 감지되었습니다). PCI1318 PCI1320 PCI1322 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있으면 해당 장치를 다시 설치하십시오. 메시지 A fatal error was detected on a component at bus devicefunction (버스 장치 기능 에 있는 구성부품에서 치명적 오류가 감지 되었습니다). LCD 메시지 Fatal error on bus device function . Power cycle system(버스 장치 기능 에 서 치명적 오류가 감지되었습니다.
오류 코드 PCI1342 PCI1344 PCI1346 PCI1348 PCI1350 106 메시지 정보 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있으면 해당 장치를 다시 설치하십시오. 메시지 A bus time-out was detected on a component at slot (슬롯 에 있는 구성부품에서 버스 타임 아 웃이 감지되었습니다). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있으면 해당 장치를 다시 설치하십시오. 메시지 An I/O channel check error was detected(I/O 채널 검사 오류 가 감지되었습니다). LCD 메시지 An I/O channel check error was detected.
오류 코드 PCI1354 PCI1356 PCI1358 PCI1360 메시지 정보 LCD 메시지 PCI parity error on slot . Re-seat PCI card(슬롯 에서 PCI 패리티 오류가 감지되었습니다. PCI 카드를 다시 장착하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있으면 해당 장치를 다시 설치하십시오. 메시지 A bus correctable error was detected on a component at slot (슬롯 에 있는 구성부품에서 수정 가능한 버스 오류가 감지되었습니다). 상세 정보 시스템 성능이 저하될 수 있습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 예정된 다음 서비스 시간에 해당 장치를 분리하고 다시 설치하 십시오.
오류 코드 PCI1362 PCI2000 PCI2002 108 메시지 정보 LCD 메시지 Bus fatal error on slot . Re-seat PCI card(슬롯 에서 치명적인 버스 오류가 감지되었습니다. PCI 카 드를 다시 장착하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있 습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있으면 해당 장치를 다시 설치하십시오. 메시지 Bus performance degraded for a component at slot (슬롯 에 있는 구성부품에 대한 버스 성능 이 저하되었습니다). 상세 정보 시스템 성능이 저하될 수 있습니다. 버스가 최대 속도 또는 대역 폭으로 작동하지 않습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다.
오류 코드 PCI3000 PCI3002 PCI3004 PCI3006 PCI3008 메시지 정보 메시지 Device option ROM on embedded NIC failed to support Link Tuning or FlexAddress(내장형 NIC의 장치 옵션 ROM이 링크 튜닝 또는 FlexAddress를 지원하지 못했습니다). 상세 정보 BIOS, BMC/iDRAC 또는 LOM 펌웨어가 오래되어 FlexAddress 를 지원하지 않습니다. 조치 BIOS, BMC/iDRAC 및 LOM 펌웨어를 업데이트합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Failed to program virtual MAC address on a component at bus devicefunction (버스 장치 기능 에 있는 구성부품에 대해 가상 MAC 주소 를 프로그래밍하지 못했습니다).
오류 코드 PCI3010 PCI3012 PCI3014 PDR0001 110 메시지 정보 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 다음 서비스 시간대에 해당 장치를 분리하고 다시 설치하십시 오. 메시지 A non-fatal IO error detected on a component at bus devicefunction (버스 장치 기능 에 있는 구성부품에서 치명적이지 않은 IO 오류가 감지되었습니다). 상세 정보 시스템 성능이 저하될 수 있습니다. 조치 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 다음 서비스 시간대에 해당 장치를 분리하고 다시 설치하십시 오. 메시지 The QuickPath Interconnect (QPI) width degraded(QPI(QuickPath Interconnect) 대역폭이 감소했습니 다).
오류 코드 PDR0002 PDR0016 PDR1001 PDR1002 PDR1016 메시지 정보 메시지 A predictive failure detected on drive (조치가 필요 한 오류가 드라이브 에서 감지되었습니다). 상세 정보 컨트롤러가 드라이브로부터 SMART 오류를 전달받습니다. 드라 이브가 작동하기는 하지만 교체되어야 합니다. 조치 다음 서비스 시간대에 드라이브를 교체해야 합니다. 메시지 Drive is removed(드라이브 Drive 이(가) 제거되었습니다). LCD 메시지 Drive is removed. Check drive(드라이브 Drive 이(가) 제거되었습니다. 드라이브를 점검하십시오). 상세 정보 컨트롤러에서 드라이브 제거를 감지했습니다. 조치 제거할 의도가 없었다면 드라이브 설치를 확인합니다. 해당 디 스크를 분리한 후 다시 장착합니다.
오류 코드 PDR1024 PST0128 PST0129 PST0130 112 메시지 정보 LCD 메시지 Drive removed from disk drive bay . Check drive(디스크 드라이브 베이 에서 드라이브 이 (가) 제거되었습니다. 드라이브를 점검하십시오). 상세 정보 드라이브가 제거되었음을 컨트롤러에서 감지했습니다. 조치 드라이브 설치를 확인합니다. 장애가 발생한 드라이브를 다시 장착합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Drive mismatch detected for drive in disk drive bay (디스크 드라이브 베이 의 드라이브 에 대해 드라이브 불일치가 감지되었습니다). LCD 메시지 Drive mismatch detected for drive in bay .
오류 코드 PST0131 PST0132 PST0133 PST0134 메시지 정보 LCD 메시지 Memory is configured, but not usable. Check memory devices(메모리가 구성되었으나 사용할 수 없습니다. 메모리 장 치를 점검하십시오). 상세 정보 메모리가 사용될 수 없게 하는 장치 오류 또는 속도 구성이 시스 템 BIOS에 의해 감지되었습니다. 조치 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기 를 참조하십시오. 메시지 System BIOS shadow failed(시스템 BIOS 섀도우가 실패했습니 다). LCD 메시지 System BIOS shadow failed. Check memory devices(시스템 BIOS 섀도우가 실패했습니다. 메모리 장치를 점검하십시오). 상세 정보 BIOS 이미지를 시스템 메모리로 복사하는 중에 메모리 오류가 발생했습니다. 조치 입력 전원을 분리합니다.
오류 코드 PST0135 PST0136 PST0137 PST0138 114 메시지 정보 상세 정보 시스템 POST 중에 시스템 BIOS가 인터럽트 컨트롤러에서 오류 를 감지했습니다. 조치 입력 전원을 제거했다가 다시 넣습니다. 문제가 계속되면 도움 말 얻기를 참조하십시오. 메시지 Timer refresh failed(타이머 갱신이 실패했습니다). LCD 메시지 Timer refresh failed. Power cycle system(타이머 갱신이 실패 했습니다. 시스템 전원을 껐다가 켜십시오). 상세 정보 시스템 POST 중에 시스템 BIOS가 타이머 갱신 오류를 감지했 습니다. 조치 입력 전원을 제거했다가 다시 넣습니다. 문제가 계속되면 도움 말 얻기를 참조하십시오. 메시지 Programmable interval timer error(프로그래밍 가능한 간격 타 이머 오류입니다). LCD 메시지 Programmable interval timer error.
오류 코드 PST0139 PST0140 PST0141 PST0142 PST0143 메시지 정보 메시지 Keyboard controller failed(키보드 컨트롤러에 오류가 있습니 다). LCD 메시지 Keyboard controller failed. Power cycle system(키보드 컨트 롤러에 오류가 있습니다. 시스템 전원을 껐다가 켜십시오). 상세 정보 시스템 BIOS가 키보드 컨트롤러에서 오류를 감지했습니다. 조치 입력 전원을 제거했다가 다시 넣습니다. 문제가 계속되면 도움 말 얻기를 참조하십시오. 메시지 System management interrupt initialization failed(시스템 관리 인터럽트 초기화에 실패했습니다). LCD 메시지 SMI initialization failed. Power cycle system(SMI 초기화에 실 패했습니다. 시스템 전원을 껐다가 켜십시오).
오류 코드 PST0192 PST0193 PST0194 PST0195 116 메시지 정보 상세 정보 TXT 부팅이 실패했습니다. 이는 메모리 오류 또는 시스템 TXT 구성의 오류와 관련되어 있을 수 있습니다. 소켓형 TPM 모듈이 제거되었을 수 있습니다. 조치 TPM이 있는지 확인합니다. 입력 전원을 제거했다가 다시 넣습 니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Shut-down test failed(종료 검사에 실패했습니다). LCD 메시지 Shut-down test failed. Power cycle system(종료 검사에 실패 했습니다. 시스템 전원을 껐다가 켜십시오). 상세 정보 POST 중에 시스템 BIOS 종료 검사가 실패했습니다. 조치 시스템 이벤트 로그에서 CMOS 전지 예외를 확인합니다. 입력 전원을 제거했다가 다시 넣습니다. 문제가 계속되면 도움말 얻 기를 참조하십시오.
오류 코드 PST0196 PST0254 PST0256 PSU0001 PSU0002 메시지 정보 조치 시스템 프로세서 구성을 검토하고 시스템 구성을 최소 수준으로 낮추십시오. 메시지 Incorrect memory configuration(잘못된 메모리 구성입니다). LCD 메시지 Incorrect memory configuration. Review User Guide(잘못된 메모리 구성입니다. 사용 설명서를 검토하십시오). 상세 정보 시스템 BIOS가 잘못된 메모리 채우기를 감지했습니다. 조치 지원되는 메모리 구성과 일치하도록 메모리를 다시 설치하십시 오. 메시지 General failure after video(비디오 설치 후의 일반 오류입니다). LCD 메시지 General failure after video. Check screen message(비디오 설 치 후의 일반 오류입니다. 화면 메시지를 확인하십시오).
오류 코드 PSU0003 PSU0004 PSU0005 118 메시지 정보 LCD 메시지 Predictive failure on PSU . Check PSU(조치가 필요 한 오류가 PSU 에서 감지되었습니다. PSU를 점검하 십시오). 상세 정보 시스템 성능 및 전원 중복성이 저하되거나 손실될 수 있습니다. 조치 다음 서비스 시간대에 전원 공급 장치를 분리했다가 다시 설치 합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The power input for power supply is lost(전원 공 급 장치 에 대한 전원 입력이 손실되었습니다). LCD 메시지 Power input for PSU is lost. Check PSU cables(PSU 에 대한 전원 입력이 손실되었습니다. PSU 케이블을 점검하십시오).
오류 코드 PSU0006 PSU0007 PSU0008 PSU0016 메시지 정보 메시지 Power supply type mismatch(전원 공급 장치 의 유형이 일치하지 않습니다). LCD 메시지 Power supply is incorrectly configured. Check PSU(전원 공급 장치 이(가) 잘못 구성되어 있습니다. PSU를 점검하십시오). 상세 정보 전원 공급 장치 간에 입력 유형 및 전원 정격이 동일해야 합니 다. 조치 일치하는 전원 공급 장치를 설치하고 본 설명서에 기술된 올바 른 구성을 검토하십시오. 메시지 Power supply is operating at 110 volts, and could cause a circuit breaker fault(전원 공급 장치 이(가) 110V로 작동 중이므로 회로 차단기 장애가 발생할 수 있습니다).
오류 코드 메시지 정보 3. PSU0031 PSU1201 PSU1202 PSU1203 PSU1204 120 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Cannot communicate with power supply (전원 공 급 장치 과(와) 통신할 수 없습니다). LCD 메시지 Cannot communicate with PSU . Re-seat PSU(PSU 과(와) 통신할 수 없습니다. PSU를 다시 장착하십시 오). 상세 정보 전원 공급 장치가 작동할 수 있지만 전원 공급 장치 모니터링이 약화됩니다. 시스템 성능이 저하될 수 있습니다. 조치 전원 공급 장치를 분리했다가 다시 설치합니다. 문제가 계속되 면 도움말 얻기를 참조하십시오. 메시지 Power supply redundancy is lost(전원 공급 장치 중복성이 손 실되었습니다).
오류 코드 메시지 정보 습니다. 리소스가 부족하여 정상적인 작동을 유지할 수 없습니 다). PWR1001 PWR1002 PWR1003 PWR1004 LCD 메시지 PSU redundancy degraded. Check PSU cables(PSU 중복성이 저하되었습니다. PSU 케이블을 점검하십시오). 상세 정보 전원 공급 장치 예외, 전원 공급 장치 인벤토리 변경 또는 시스 템 전원 인벤토리 변경 때문에 현재의 전원 작동 모드가 중복되 지 않습니다. 조치 이벤트 로그에서 전원 공급 장치 오류를 확인합니다. 시스템 구 성 및 전력 사용량을 검토하십시오. 메시지 The system performance was degraded(시스템 성능이 저하되 었습니다). LCD 메시지 System performance degraded. Check PSUs and system configuration(시스템 성능이 저하되었습니다. PSU 및 시스템 구성을 점검하십시오).
오류 코드 PWR1005 PWR1006 PWR1007 PWR1008 122 메시지 정보 상세 정보 시스템 전원이 꺼지거나 시스템이 성능 저하 상태에서 작동할 수 있습니다. 조치 이벤트 로그에서 전원 공급 장치 오류를 확인합니다. 시스템 구 성 및 전력 사용량을 검토하고 그에 따라 전원 공급 장치를 업그 레이드하거나 설치하십시오. 메시지 The system performance degraded because the userdefined power capacity has changed(사용자 정의 전원 용량이 변경되었기 때문에 시스템 성능이 저하되었습니다). 상세 정보 사용자 정의 전원 설정이 시스템 작동에 영향을 미쳤습니다. 조치 이 문제가 의도치 않게 발생한 경우라면 시스템 구성 변경 사항 및 전원 정책을 검토하십시오.
오류 코드 RFM1003 RFM1005 RFM1006 RFM1008 메시지 정보 LCD 메시지 System power exceeds threshold. Performance degraded. Check PSU configuration(시스템 전원이 임계값을 초과합니다. 성능이 저하되었습니다. PSU 구성을 점검하십시오). 상세 정보 전원 임계값은 사용자에 의해 구성되거나 시스템 구성을 기반으 로 소프트웨어에 의해 자동으로 구성됩니다. 조치 시스템 구성을 검토하고 전원 공급 장치를 업그레이드하거나 시 스템 전력 소비량을 줄이십시오. 메시지 Removable Flash Media is not IPMI-function ready(이동식 플래시 미디어 에 IPMI 기능이 아직 준비 되어 있지 않습니다). 상세 정보 이동식 플래시 미디어가 설치되어 있지만 잘못 구성되거나 초기 화되지 못했습니다.
오류 코드 RFM1014 RFM1016 RFM1021 RFM1022 RFM1023 RFM1024 124 메시지 정보 메시지 Removable Flash Media is write protected(이동식 플 래시 미디어 이(가) 쓰기 방지되어 있습니다). LCD 메시지 Removable Flash Media is write protected. Check SD Card(이동식 플래시 미디어 이(가) 쓰기 방지되어 있습니다. SD 카드를 점검하십시오). 상세 정보 SD 카드의 물리적 래치에 의해 카드가 쓰기 방지되어 있습니다. 쓰기 방지된 카드는 사용할 수 없습니다. 조치 이 문제가 의도치 않게 발생한 경우라면 미디어를 제거하고 쓰 기 방지를 비활성화하십시오. 메시지 Media not present for Removable Flash Media (이동 식 플래시 미디어 에 대한 미디어가 없습니다).
오류 코드 RFM1026 RFM1032 RFM1034 RFM1201 RFM1202 메시지 정보 상세 정보 부팅 시, 카드의 CID(Card Identification) 서명이 NV(NonVolatile) 저장 값과 다르거나 카드가 진행 중인 복사 작업의 대 상입니다. 조치 이 문제가 의도치 않게 발생한 경우라면 플래시 미디어를 다시 설치하십시오. 메시지 Failure detected on Removable Flash Media(이동식 플래시 미 디어에서 오류가 감지되었습니다). 상세 정보 SD 카드 읽기 또는 쓰기 중에 오류가 보고되었습니다. 조치 플래시 미디어를 다시 설치합니다. 문제가 계속되면 미디어를 교체하십시오. 메시지 Removable Flash Media is write protected(이동식 플래시 미디 어가 쓰기 방지되어 있습니다). 상세 정보 SD 카드의 물리적 래치에 의해 카드가 쓰기 방지되어 있습니다.
오류 코드 RFM1203 RFM1205 RFM2001 RFM2002 RFM2004 126 메시지 정보 조치 오류가 발생한 SD 카드를 교체하십시오. 메시지 Internal Dual SD Module is not redundant(내부 이중 SD 모듈 이 중복되지 않습니다). 상세 정보 내부 이중 SD 모듈이 중복되지 않습니다. 조치 중복이 필요하면 SD 카드를 추가로 설치하고 구성하여 중복되 도록 하십시오. 메시지 Internal Dual SD Module is not redundant. Insufficient resources to maintain normal operations(내부 이중 SD 모듈 이 중복되지 않습니다. 리소스가 부족하여 정상적인 작동을 유 지할 수 없습니다). LCD 메시지 Internal Dual SD Module is not redundant. Insufficient resources.
오류 코드 RFM2006 SEC0000 SEC0001 SEC0002 SEC0003 메시지 정보 LCD 메시지 Internal Dual SD Module failed. Check SD Card(내부 이중 SD 모듈 에 오류가 발생했습니다. SD 카드를 점검 하십시오). 상세 정보 SD 카드 모듈이 설치되어 있지만 잘못 구성되거나 초기화되지 못했습니다. 조치 SD 모듈을 다시 설치하고 SD 카드를 분리한 후 다시 설치하십 시오. 메시지 Internal Dual SD Module is write protected(내부 이중 SD 모듈 이(가) 쓰기 방지되어 있습니다). 상세 정보 모듈이 쓰기 방지되어 있습니다. 변경 사항이 미디어에 기록되 지 않을 수 있습니다. 조치 이 문제가 의도치 않게 발생한 경우라면 미디어를 제거하고 쓰 기 방지를 비활성화하십시오. 메시지 The chassis is open(섀시가 열려 있습니다).
오류 코드 SEC0004 SEC0005 SEC0006 SEC0031 SEC0033 128 메시지 정보 메시지 The LAN is disconnected(LAN 연결이 끊어졌습니다). 상세 정보 The LAN is disconnected. Network performance may be degraded(LAN 연결이 끊어졌습니다. 네트워크 성능이 저하될 수 있습니다). 조치 이 문제가 의도치 않게 발생한 경우라면 네트워크 케이블을 연 결하십시오. 메시지 Unauthorized docking is detected(허가되지 않은 도킹이 감지 되었습니다). 상세 정보 이동식 구성부품이 변조되었거나 잘못 설치되었거나 시스템 요 구 사항을 충족하지 못합니다. 조치 이동식 하드웨어 구성부품이 올바로 설치되었는지 확인합니다. 설치 설명서를 검토하십시오. 메시지 The fan area is open(팬 영역이 열려 있습니다). 상세 정보 The fan area is open.
오류 코드 SEC0040 SEC0041 SEC0042 SEC0043 SEC0044 메시지 정보 메시지 A critical stop occurred during OS load(OS 로드 중에 치명적 인 중지가 발생했습니다). 상세 정보 운영 체제에서 중대한 중지 IPMI 이벤트를 생성했습니다(센서 유형 = 20H). 조치 비디오 및 운영 체제 로그에서 추가적인 정보를 확인하십시오. 메시지 BIOS detected an error configuring the Intel Trusted Execution Technology (TXT)(Intel TXT(Trusted Execution Technology) 구성 중에 BIOS가 오류를 감지했습니다). LCD 메시지 BIOS detected an error configuring TXT. Check system configuration(TXT 구성 중에 BIOS가 오류를 감지했습니다. 시 스템 구성을 점검하십시오).
오류 코드 메시지 정보 코드 모듈이 Intel TXT(Trusted Execution Technology) 오류를 감지했습니다). SEC0600 SEC0602 SEC0604 SEC0606 SEC0608 130 LCD 메시지 SINIT detected a TXT error at boot. Check system configuration(부팅 시 SINIT가 TXT 오류를 감지했습니다. 시스 템 구성을 점검하십시오). 상세 정보 TXT 초기화 오류입니다. 시스템 구성이 변경되었을 수 있습니 다. 조치 시스템 하드웨어 인벤토리 및 소프트웨어 구성을 점검하십시오. 메시지 A secure mode violation detected(안전 모드 위반이 감지되었 습니다). 상세 정보 이 메시지는 물리적 또는 원격 액세스 시도에 대해 적용될 수 있 습니다. 조치 시스템 로그에서 침입 시도를 확인하고 강력한 암호 정책을 확 립하십시오.
오류 코드 SEC0610 SEL0002 SEL0006 SEL0008 SEL0010 메시지 정보 상세 정보 이 메시지는 물리적 또는 원격 액세스 시도에 대해 적용될 수 있 습니다. 조치 시스템 로그에서 침입 시도를 확인하고 강력한 암호 정책을 확 립하십시오. 메시지 An Out-of-band password violation detected(대역외 암호 위 반이 감지되었습니다). 상세 정보 이 메시지는 원격 액세스 시도에 대해 적용될 수 있습니다. 조치 시스템 로그에서 침입 시도를 확인하고 강력한 암호 정책을 확 립하십시오. 메시지 Logging is disabled(로깅이 비활성화되어 있습니다). 상세 정보 이 메시지는 특정 유형의 이벤트 로깅이 사용자에 의해 비활성 화된 경우 표시됩니다. 조치 의도치 않게 이 문제가 발생한 경우라면 로깅을 다시 활성화하 십시오.
오류 코드 SEL0012 SEL1204 SEL1209 SEL1211 SEL1300 132 메시지 정보 메시지 Could not create or initialize the system event log(시스템 이 벤트 로그를 생성하거나 초기화할 수 없습니다). 상세 정보 시스템 이벤트 로그가 초기화되지 못하면 플랫폼 상태 및 오류 이벤트가 캡처되지 않습니다. 일부 관리 소프트웨어는 플랫폼 예외를 보고하지 않습니다. 조치 관리 컨트롤러 또는 iDRAC를 재부팅합니다. 시스템 입력 전원 을 껐다가 켜십시오. 문제가 계속되면 지원 부서에 연락하십시 오. 메시지 An unknown system hardware failure detected(알 수 없는 시 스템 하드웨어 오류가 감지되었습니다). LCD 메시지 Unknown system hardware failure(알 수 없는 시스템 하드웨어 오류입니다).
오류 코드 SEL1302 SEL1304 SEL1306 SEL1308 SEL1501 메시지 정보 상세 정보 시스템 설정에서 시스템 부팅 순서를 표시합니다. 로컬 비디오 화면에도 추가적인 정보가 표시될 수 있습니다(IPMI 센서 유형 코드 1eh - 오프셋 00h). 조치 시스템 부팅 설정을 점검합니다. 대량 저장 장치 컨트롤러 구성 설정이 적용 가능한지 확인하십시오. 메시지 Non-bootable diskette detected(부팅할 수 없는 디스켓이 감 지되었습니다). 상세 정보 드라이브의 디스크가 올바로 포맷되지 않았거나 필요한 운영 체 제 파일을 포함하지 않습니다. 조치 디스켓을 부팅 가능한 디스크로 교체하십시오. 메시지 The PXE server not found(PXE 서버를 찾지 못했습니다). 상세 정보 PXE는 네트워크에서 시스템을 부팅하는 한 가지 방법입니다. 조치 네트워크 및 PXE 서버 구성을 점검하십시오.
오류 코드 SEL1502 SEL1504 SEL1506 SEL1508 SEL1510 SEL9900 134 메시지 정보 메시지 Chassis management controller (CMC) redundancy is degraded(CMC(Chassis Management Controller) 중복성이 저 하되었습니다). 상세 정보 CMC 중복성을 훼손하는 작업 또는 오류가 발생했습니다. 조치 CMC 네트워크 케이블 및 네트워크 연결을 점검합니다. CMC 펌웨어 버전이 일치하는지 확인하십시오. 메시지 The chassis management controller (CMC) is not redundant. Insufficient resources to maintain normal operations(CMC(Chassis Management Controller)가 중복되 지 않습니다. 리소스가 부족하여 정상적인 작동을 유지할 수 없 습니다).
오류 코드 메시지 정보 Ipmitool -vvv 또는 Racadm -E와 같이 사용하여 이 이벤트를 검토해야 할 수도 있습니다. SWC4004 SWC4006 SWC4008 SWC5001 TMP0100 조치 관리 소프트웨어를 업그레이드하십시오. 메시지 A firmware or software incompatibility detected between iDRAC in slot and CMC(슬롯 에 있는 iDRAC와 CMC 간에 펌웨어 또는 소프트웨어 비호환성이 감지 되었습니다). 상세 정보 FlexAddress가 펌웨어 버전 중 하나에서 구현되지 않습니다. 조치 iDRAC와 CMC의 펌웨어 버전을 확인합니다. 최신 버전으로 업 데이트하십시오.
오류 코드 TMP0101 TMP0102 TMP0103 TMP0104 136 메시지 정보 조치 시스템 작동 환경을 점검하십시오. 메시지 The system board temperature is less than the lower critical threshold(시스템 보드 의 온도가 중대 임계값 하한보다 낮습니다). LCD 메시지 System board temperature is outside of range(시스 템 보드 의 온도가 범위를 벗어납니다). 상세 정보 주변 공기 온도가 너무 낮습니다. 조치 시스템 작동 환경을 점검하십시오. 메시지 The system board temperature is greater than the upper warning threshold(시스템 보드 의 온도가 경고 임계값 상한보다 높습니다).
오류 코드 TMP0106 TMP0107 TMP0108 TMP0109 메시지 정보 조치 The system board temperature is outside of the optimum range. Check Fans(시스템 보드 의 온도가 최적 범위를 벗어납니다. 팬을 점검하십시오). 메시지 The memory module temperature is less than the lower warning threshold(메모리 모듈 의 온도가 경 고 임계값 하한보다 낮습니다). LCD 메시지 Memory module temperature is outside of range(메모리 모듈 온도가 범위를 벗어납니다). 상세 정보 주변 공기 온도가 너무 낮습니다. 조치 시스템 작동 환경을 점검하십시오.
오류 코드 TMP0110 TMP0112 TMP0113 TMP0114 TMP0115 138 메시지 정보 조치 시스템 보드 의 온도가 최적 범위를 벗어납니다. 팬을 점검하십시오. 메시지 The memory module temperature is outside of range(메모리 모듈 온도가 범위를 벗어납니다). LCD 메시지 Memory module temperature is outside of range. Check Fans(메모리 모듈 온도가 범위를 벗어납니다. 팬을 점검하십시오). 상세 정보 주변 공기 온도가 너무 높거나 낮습니다. 조치 시스템 작동 환경을 점검하십시오. 메시지 The temperature is less than the lower warning threshold(의 온도가 경고 임계값 하한보다 낮습니다).
오류 코드 TMP0116 TMP0118 TMP0119 TMP0120 메시지 정보 LCD 메시지 The temperature is outside of range. Check Fans(의 온도가 범위를 벗어납니다. 팬을 점검하십시 오). 상세 정보 주변 공기 온도가 너무 높거나 1개 이상의 팬에서 오류가 발생했 습니다. 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오. 메시지 The temperature is outside of range(의 온도 가 범위를 벗어납니다). LCD 메시지 The temperature is outside of range. Check Fans(의 온도가 범위를 벗어납니다. 팬을 점검하십시 오). 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오.
오류 코드 TMP0121 TMP0122 TMP0100 TMP0104 140 메시지 정보 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오. 메시지 The system inlet temperature is greater than the upper critical threshold(시스템 입구 온도가 중대 임계값 상한보다 높 습니다). LCD 메시지 System inlet temperature is outside of range. Check Fans(시스템 입구 의 온도가 범위를 벗어납니다. 팬을 점검하십시오). 상세 정보 주변 공기 온도가 너무 높거나 1개 이상의 팬에서 오류가 발생했 습니다. 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오. 메시지 The system inlet temperature is outside of range(시스템 입구 온도가 범위를 벗어납니다).
오류 코드 TMP0126 TMP0128 TMP0130 TMP0132 메시지 정보 메시지 Disk drive bay temperature is greater than the upper warning threshold(디스크 드라이브 베이 온도가 경고 임계값 상한보다 높습니다). LCD 메시지 Disk drive bay temperature is outside of range. Check Fans(디스크 드라이브 베이 온도가 범위를 벗어납니다. 팬을 점 검하십시오). 상세 정보 주변 공기 온도가 너무 높거나 1개 이상의 팬에서 오류가 발생했 습니다. 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오. 메시지 Disk drive bay temperature is outside of the allowable range(디스크 드라이브 베이 온도가 허용 범위를 벗어납니다).
오류 코드 TMP0134 VLT0100 메시지 정보 메시지 The control panel temperature is outside of the allowable range(제어 패널 온도가 허용 범위를 벗어납니다). LCD 메시지 Control panel temperature is outside of range(제어 패널 온도 가 범위를 벗어납니다). 상세 정보 주변 공기 온도가 너무 높거나 낮습니다. 조치 시스템 작동 환경을 점검하고 이벤트 로그를 검토하여 팬 오류 를 확인하십시오. 메시지 Processor module voltage is less than the lower warning threshold(프로세서 모듈 전압이 경고 임계값 하한보다 낮습니다). LCD 메시지 Processor module voltage is outside of range(프로세 서 모듈 전압이 범위를 벗어납니다).
오류 코드 VLT0102 메시지 정보 메시지 Processor module voltage is greater than the upper warning threshold(프로세서 모듈 전압이 경고 임계값 상한보다 높습니다). LCD 메시지 Processor module voltage is outside of range(프로세 서 모듈 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0103 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 프로세서 모듈을 분리합니다. 프로세서 소켓에 굽은 핀이 없는지 검사하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 조치 VLT0200 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 프로세서 모듈을 분리합니다. 프로세서 소켓에 굽은 핀이 없는지 검사하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The system board voltage is less than the lower critical threshold(시스템 보드 의 전압이 중대 임계값 하한보다 낮습니다). LCD 메시지 System board voltage is outside of range(시스템 보드 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0201 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 프로세서 모듈을 분리합니다.
오류 코드 메시지 정보 LCD 메시지 System board voltage is outside of range(시스템 보드 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0203 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The system board voltage is greater than the upper critical threshold(시스템 보드 의 전압이 중대 임계값 상한보다 높습니다).
오류 코드 메시지 정보 3. VLT0206 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The memory module voltage is less than the lower warning threshold(메모리 모듈 의 전압이 경고 임계값 하한보다 낮습니다). LCD 메시지 Memory module voltage is outside of range(메모리 모듈 의 전압이 범위를 벗어 납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0207 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3.
오류 코드 메시지 정보 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0209 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The memory module voltage is greater than the upper critical threshold(메모리 모듈 의 전압이 중대 임계값 상한보다 높습니다). LCD 메시지 Memory module voltage is outside of range(메모리 모듈 의 전압이 범위를 벗어 납니다).
오류 코드 메시지 정보 3. VLT0212 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The disk drive bay voltage is less than the lower warning threshold(디스크 드라이브 베이 의 전압이 경 고 임계값 하한보다 낮습니다). LCD 메시지 The disk drive bay voltage is outside of range(디스크 드라이브 베이 의 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0213 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0215 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The disk drive bay voltage is greater than the upper critical threshold(디스크 드라이브 베이 의 전압이 중 대 임계값 상한보다 높습니다). LCD 메시지 The disk drive bay voltage is outside of range(디스크 드라이브 베이 의 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다.
오류 코드 VLT0218 메시지 정보 메시지 The voltage is less than the lower warning threshold(의 전압이 경고 임계값 하한보다 낮습니다). LCD 메시지 The voltage is outside of range(의 전압이 범 위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0219 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 VLT0221 메시지 정보 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The voltage is greater than the upper critical threshold(의 전압이 중대 임계값 상한보다 높습니다). LCD 메시지 The voltage is outside of range(의 전압이 범 위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0222 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0225 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The memory module voltage is less than the lower critical threshold(메모리 모듈 의 전압이 중대 임계값 하한보다 낮습니다). LCD 메시지 Memory module voltage is outside of range(메모리 모듈 의 전압이 범위를 벗어 납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다.
오류 코드 VLT0227 메시지 정보 메시지 The memory module voltage is greater than the upper critical threshold(메모리 모듈 의 전압이 중대 임계값 상한보다 높습니다). LCD 메시지 Memory module voltage is outside of range(메모리 모듈 의 전압이 범위를 벗어 납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0228 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검 한 후 다시 설치하십시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 조치 VLT0231 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 메자닌 카드를 다시 장착합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The mezzanine card voltage is less than the lower critical threshold(메자닌 카드 의 전압이 중대 임계값 하한보다 낮습니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 VLT0232 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 메자닌 카드를 다시 장착합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 VLT0234 메시지 정보 2. 메자닌 카드를 다시 장착합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 The mezzanine card voltage is outside of range(메자닌 카드 의 전압이 범위를 벗어 납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시 스템 전원이 꺼질 수 있습니다. 조치 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확 인합니다. 2. 메자닌 카드를 다시 장착합니다. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 경고 메시지 경고 메시지는 발생 가능한 문제를 경고하고 시스템이 작업을 계속하기 전에 사용자가 응답하도록 요청합니 다. 예를 들면, 디스켓을 포맷하기 전에 디스켓에 있는 모든 데이터를 유실하게 됨을 경고하는 메시지가 표시 됩니다.
9 도움말 얻기 Dell에 문의하기 노트: 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서, 포장 명세서, 청구서 또는 Dell 제품 카탈로그 에서 연락처 정보를 찾을 수 있습니다. Dell은 다양한 온라인/전화 기반의 지원 및 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 1. dell.com/support로 이동합니다. 2. 지원 카테고리를 선택합니다. 3. 페이지 맨 아래에 있는 Choose a Country/Region(국가/지역 선택) 드롭다운 메뉴에서 국가 또는 지역을 확인합니다. 4. 필요한 서비스 또는 지원 링크를 선택하십시오.