Dell™ PowerEdge™ M905, M805, M605, and M600 Getting Started With Your System Guide de mise en route Primeiros passos com o sistema Procedimientos iniciales con el sistema
Dell™ PowerEdge™ M905, M805, M605, and M600 Getting Started With Your System
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2008 Dell Inc. All rights reserved.
System Features This section describes the major hardware and software features of your system. It also provides information about other documents you may need when setting up your system and how to obtain technical assistance. System Enclosure Features The M1000e system enclosure (chassis) includes the following features: Scalability Features • Support for up to 16 half-height or 8 full-height blades (server modules).
Systems Management Features • A Chassis Management Controller (CMC), which provides several essential systems management features: – 4 Enclosure-level power management and thermal management: • The CMC monitors system power requirements and supports the optional Dynamic Power Supply Engagement mode so that the CMC can enable or place power supplies in standby dynamically, depending on load and redundancy requirements, to improve power efficiency. • The CMC reports real-time power consumption.
The CMC has two Ethernet ports. "Gb1" is used to connect to the external management network. "Stack" allows CMCs in adjacent enclosures to be daisy-chained. A 24-port Ethernet switch provides internal 100-Mb communication with the blades, I/O modules, optional iKVM, and optional second, redundant CMC, and provides a 10/100/1000-Mb connection to the external management network.
Blade Features Performance Features PowerEdge M905 • Four AMD™ Opteron™ 8000 Series dual-core or quad-core processors. • A minimum of 8 GB of 677 MHz DDR2 memory modules, upgradable to a maximum of 192 GB by installing pairs of 1-GB, 2-GB, 4-GB, or 8-GB modules in the 24 memory module sockets on the blade system board. The blade also supports memory sparing if eight or sixteen memory module sockets are populated with identical memory modules.
PowerEdge M605 • One or two AMD Opteron 2000 Series dual-core or quad-core processors. • A minimum of 1 GB of 677-MHz or 800-MHz DDR2 memory modules, upgradable to a maximum of 64 GB by installing pairs of 512-MB, 1-GB, 2-GB, 4-GB, or 8-GB modules in the eight memory module sockets on the blade system board. The blade also supports memory sparing. Common Features • The PowerEdge M805 and M905 blades support one or two 2.5 inch SAS hard drives.
The following software is included with your system: • A System Setup program for quickly viewing and changing system configuration information. For more information on this program, see "Using the System Setup Program" in your Hardware Owner’s Manual. • Enhanced security features, including a system password and a setup password, available through the System Setup program. • System diagnostics for evaluating system components and devices.
• Red Hat Enterprise Linux Server AS and ES (version 5) (ia32) • Red Hat Enterprise Linux Server AS, ES, and WS (version 5) and EM64T • SUSE® Linux Enterprise Server 9 (x86_64) with SP3 and EM64T • SUSE Linux Enterprise Server 10 (x86_64) and EM64T • VMWare® ESX 3.1 • VMWare ESX 3.5 Other Information You May Need CAUTION: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document.
• Updates are sometimes included with the system to describe changes to the system, software, and/or documentation. NOTE: Always check for updates on support.dell.com and read the updates first because they often supersede information in other documents. • Release notes or readme files may be included to provide last-minute updates to the system or documentation or advanced technical reference material intended for experienced users or technicians.
Install the System in a Rack Install the system in the rack once you have read the "Safety Instructions" located in the rack installation documentation for your system. See your rack installation documentation for instructions on installing your system in a rack. For power and cooling guidelines, see the rack capacity planner tool on www.dell.com. Install the Blades Beginning at the top, slide the modules into the enclosure from left to right.
Connect the CMC and KVM Modules Connect the serial cable and network cable from the management system to the CMC module. If a second, optional CMC module is installed, connect it as well. (If your chassis was shipped with M805 or M905 blades pre-installed, the included CMC firmware will be version 1.2 or greater.) Connect the keyboard, mouse, and monitor to the optional iKVM module. Connect the System to Power Connect the system’s power cables to the system power supplies.
Turn on the System Press the power button on the enclosure. The power indicator should light.
Turn on the Blades Press the power button on each blade, or power on the blades using the systems management software. Complete the 0perating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the Quick Installation Guide. Be sure the operating system is installed before installing hardware or software not purchased with the system.
Technical Specifications Blade Specifications Processor Processor type PowerEdge M905 Four dual-core or quad-core AMD Opteron 8000 Series processors PowerEdge M805 Two dual-core or quad-core AMD Opteron 2000 Series processors PowerEdge M600 One or two dual-core or quad-core Intel Xeon processors PowerEdge M605 One or two dual-core or quad-core AMD Opteron 2000 Series processors Memory Architecture PowerEdge M600 FBD memory modules, rated for 677-MHz operation PowerEdge M905, M805, M605 DDR2 memor
Memory Maximum RAM PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M600, M605 64 GB Drives Hard Drives PowerEdge M805, M905 One or two 2.5-inch SAS hard drives PowerEdge M600, M605 SATA configuration One or two 2.5-inch SATA hard drives SAS configuration One or two 2.5-inch SAS hard drives NOTE: SAS and SATA hard drives cannot be mixed within a M600 or M605 blade. Connectors External USB PowerEdge M805, M905 Three 4-pin, USB 2.0 compliant PowerEdge M600, M605 Two 4-pin, USB 2.
Video Controller Video type ATI RN50 video controller Video memory 32 MB Physical PowerEdge M905, M805 Height 38.5cm (15.2 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 11.1 kg (24.5 lb) PowerEdge M605, M600 Height 18.9 cm (7.4 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 5.2-6.4 kg (11.5-14.0 lb) Battery Blade battery CR 2032 3.0-V lithium ion coin cell System Enclosure Specifications Physical Height 44.0 cm (17.
Power Supply Module AC/DC power supply (per power supply) Wattage 2360 W Connector NEMA C20 receptacle Heat dissipation 1205 BTU/hr. maximum Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less. System Voltage Requirements 200 - 240V, 16A, 3-Phase, 50 /60Hz 200 - 240V, 40.
Enclosure Control Panel Externally accessible connectors USB PowerEdge M905, M805 Three 4-pin, USB 2.0-compliant connectors for keyboard and mouse support PowerEdge M605, M600 Two 4-pin, USB 2.
Fibre Channel Pass-Through Module Externally accessible connectors Fibre Channel transceiver Sixteen external SFP ports that support 1/2/4-Gbps FC speeds Brocade Fibre Channel Switch Module Externally accessible connectors Fibre Channel Eight physical FC ports (four enabled by default, upgradeable to eight) supporting 1/2/4-Gbps Fibre Channel connections Serial Port RJ-45 Environmental NOTE: For additional information about environmental measurements for specific system configurations, see dell.
Environmental (continued) Maximum shock Operating One shock pulse in the positive z axis of 31 G for up to 2.
22 Getting Started With Your System
Systèmes Dell™ PowerEdge™ M905, M805, M605 et M600 Guide de mise en route
Remarques, avis et précautions REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : Un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION ! Une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document peuvent être modifiées sans préavis.
Caractéristiques du système Cette section décrit les principales caractéristiques matérielles et logicielles du système. Elle contient également des informations relatives à d'autres documents pouvant être utiles à la configuration du système et indique comment obtenir une assistance technique.
Gestion des systèmes • Contrôleur CMC (Chassis Management Controller) fournissant plusieurs fonctions essentielles de gestion des systèmes : – 26 Gestion de l'alimentation et des températures au niveau du châssis : • Le contrôleur CMC surveille les besoins en alimentation du système et prend en charge l'utilisation du mode DPSE (Dynamic Power Supply Engagement) fourni en option.
– Un emplacement carte mémoire Secure Digital sur la carte CMC prend en charge une fonction permanente WWN/MAC (en option) qui permet d'utiliser des WWN/MAC à emplacement pour les lames, ce qui simplifie leur installation et leur remplacement. Le contrôleur CMC comprend deux ports Ethernet. Le port “Gb1” est utilisé pour la connexion au réseau de gestion externe. Le port “Stack” permet de relier en série les contrôleurs CMC installés dans des châssis adjacents.
– Le module KVM intégré est également accessible à partir du panneau de commande situé à l'avant du châssis. Il est possible d'utiliser le module KVM situé à l'avant ou à l'arrière, mais pas les deux simultanément. REMARQUE : Le module frontal est activé par défaut en cas de conflit entre les ports situés à l'avant et à l'arrière du module iKVM. L'accès au module iKVM frontal peut être désactivé via l'interface utilisateur du contrôleur CMC.
PowerEdge M600 • Un ou deux processeurs Intel® Xeon® double coeur ou quadruple coeur • Un minimum de 1 Go constitué de barrettes de mémoire FBD de 677 MHz, extensible à 64 Go au maximum par l'installion de paires de barrettes de 512 Mo ou de 1, 2, 4 ou 8 Go dans les huit sockets prévus à cet effet sur la carte système de la lame. Si les huit emplacements mémoire contiennent des modules identiques, il est possible d'utiliser une mémoire de réserve ou une mise en miroir.
• Sous-système vidéo intégré compatible VGA comprenant un contrôleur vidéo ATI RN50. Ce sous-système vidéo contient 32 Mo de mémoire vidéo SDRAM (non extensible). La résolution maximale est de 1280x1024x 65000 couleurs (non-entrelacé).
• Logiciel de gestion des systèmes et documentation associée. Les logiciels de gestion des systèmes permettent de gérer et de surveiller chaque lame de façon individuelle, mais aussi le système dans son ensemble, en incluant les lames, les modules de commutation réseau, les blocs d'alimentation et les ventilateurs. Ces logiciels peuvent être utilisés pour gérer le système localement ou à distance via le réseau. Dell recommande l'utilisation du logiciel de gestion des systèmes fourni avec le système.
Autres informations utiles PRÉCAUTION ! Consultez les informations de sécurité et de garantie fournies avec votre système. Les informations sur la garantie se trouvent soit dans ce document, soit à part. • Le Configuration Guide (Guide de configuration) fournit des informations sur la configuration du châssis du système et des lames.
Obtention d'une assistance technique Si vous ne comprenez pas une procédure décrite dans ce guide ou si le système ne réagit pas comme prévu, reportez-vous au document Hardware Owner's Manual (Manuel du propriétaire). Des formations et certifications Dell Enterprise sont disponibles. Pour plus d'informations, consultez le site dell.com/training. Ce service n'est disponible que dans certains pays.
Installation des lames Insérez les modules dans le châssis en commençant par le haut et en procédant de gauche à droite. Lorsqu'une lame est correctement installée, la poignée revient en position fermée.
Connexion du contrôleur CMC et des modules KVM Connectez les câbles série et réseau du système de gestion au module CMC. Si un second module CMC en option est installé, connectez-le également. Si votre châssis a été fourni avec des lames M805 ou M905 préinstallées, le micrologiciel CMC inclus est de version 1.2 ou ultérieure. Connectez le clavier, la souris et le moniteur au module iKVM en option.
Mise sous tension du système Appuyez sur le bouton d'alimentation du châssis. Le voyant d'alimentation doit s'allumer.
Mise sous tension des lames Mettez chaque lame sous tension en appuyant sur son bouton d'alimentation ou en utilisant le logiciel de gestion des systèmes. Finalisation de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez tout d'abord la documentation associée, qui a été fournie avec l'ordinateur. Si vous installez un système d'exploitation pour la première fois, consultez le document Quick Installation Guide (Guide d'installation rapide).
Spécifications techniques Spécifications des lames Processeur Type de processeur PowerEdge M905 Quatre processeurs AMD Opteron 8000 Series double coeur ou quadruple coeur PowerEdge M805 Deux processeurs AMD Opteron 2000 Series double coeur ou quadruple coeur PowerEdge M600 Un ou deux processeurs Intel Xeon double coeur ou quadruple coeur.
Mémoire (suite) RAM maximale PowerEdge M905 192 Go PowerEdge M805 128 Go PowerEdge M600, M605 64 Go Lecteurs Disques durs PowerEdge M805, M905 Un ou deux disques durs SAS enfichables à chaud de 2,5 pouces PowerEdge M600, M605 Configuration SATA Un ou deux disques durs SATA de 2,5 pouces Configuration SAS Un ou deux disques durs SAS de 2,5 pouces REMARQUE : Une lame M600 ou M605 ne peut pas contenir à la fois des disques durs de type SAS et SATA.
Contrôleurs Ethernet Circuit microprogrammé PowerEdge M805, M905 Quatre ports Ethernet avec prise en charge TOE et amorçage iSCSI, assurée par deux contrôleurs Ethernet Broadcom 5709S à double port PowerEdge M600, M605 Deux ports Ethernet avec prise en charge TOE et amorçage iSCSI, assurée par deux contrôleurs Broadcom 5708S intégrés Contrôleur vidéo Type de vidéo Contrôleur vidéo ATI RN50 Mémoire vidéo 32 Mo Caractéristiques physiques PowerEdge M905, M805 Hauteur 38,5 cm (15,2 pouce) Largeur 5 c
Spécifications du châssis Caractéristiques physiques Hauteur 44,0 cm (17,3 pouces) Largeur 44,7 cm (17,6 pouces) Profondeur 75,5 cm (29,7 pouces) Poids (configuration maximale) 178,3 kg (392,2 livres) Poids (à vide) 44,6 kg (98,1 livres) Bloc d'alimentation Bloc d'alimentation en CA/CC (selon la tension en vigueur) Puissance 2360 W Connecteur Connecteur C20 NEMA Dissipation thermique 1205 BTU/h.
Module contrôleur de gestion du châssis (CMC) Connecteurs accessibles de l'extérieur Gestion à distance Deux connecteurs RJ-45 10/100/1000 Mbps dédiés pour le contrôleur d'accès à distance Ethernet intégré. Série Connecteur DTE à 9 broches, compatible 16550 Vidéo VGA, 15 broches Batterie Pile bouton au lithium-ion CR2032 (3 V) Carte Secure Digital Un emplacement pour carte Secure Digital dédié à la prise en charge de FlexAddress.
Spécifications des modules d'E/S Module commutateur Ethernet PowerConnect M6220 Connecteurs accessibles de l'extérieur Ethernet - 10/100/1000 Mbps Quatre ports RJ-45 à négociation automatique Série Un connecteur USB 2.0 de type A à quatre broches. Pour la connexion à la console, utilisez l'adaptateur USB fourni (type A vers DB9). Modules en option Deux baies d'option.
Environnement REMARQUE : Pour plus d'informations concernant les mesures d'exploitation liées à différentes configurations spécifiques, rendez-vous à l'adresse dell.com/environmental_datasheets. Le système n'est pas conçu pour être utilisé dans un bureau. Température Fonctionnement De 10° à 35°C (50 à 95°F) REMARQUE : Au-dessus de 900 m (2955 pieds), la température maximale doit être diminuée de 1°C (1,8°F) tous les 300 m (985 pieds).
Dell™ PowerEdge™ M905, M805, M605 e M600 Primeiros passos com o sistema
Notas, avisos e advertências NOTA: As NOTAS fornecem informações importantes que o ajudam a utilizar melhor o computador. AVISO: As mensagens de AVISO informam sobre possíveis danos ao hardware ou perda de dados e indicam como evitar o problema. ADVERTÊNCIA: As mensagens de ADVERTÊNCIA indicam possíveis danos de propriedade, ferimentos pessoais ou morte. ____________________ As informações contidas neste documento estão sujeitas a alterações sem aviso prévio. © 2008 Dell Inc. Todos os direitos reservados.
Recursos do sistema Esta seção descreve os principais recursos de hardware e software do sistema. Também fornece informações sobre outros documentos que podem ser úteis durante a configuração do sistema e quando precisar de assistência técnica. Recursos da caixa do sistema A caixa do sistema (chassi) M1000e inclui os seguintes recursos: Recursos de escalabilidade • Suporte para até 16 blades de meia altura e 8 de altura total (módulos de servidor).
Recursos de gerenciamento do sistema • Um controlador de gerenciamento do chassi (CMC) que fornece vários recursos essenciais para o gerenciamento do sistema: – 48 Gerenciamento de energia e gerenciamento térmico da caixa: • O CMC monitora os requisitos de energia do sistema e oferece suporte ao modo opcional de ajuste de fonte de energia dinâmica para poder ativar as fontes de alimentação ou colocá-las no modo de espera dinamicamente para otimizar a energia, dependendo dos requisitos de carga e redund
O CMC possui duas portas Ethernet. A porta "Gb1" é usada para conectar à rede externa de gerenciamento. A "pilha" permite que os CMCs em caixas adjacentes sejam conectados em margarida. Um comutador Ethernet de 24 portas fornece comunicação interna de 100 Mb com as lâminas, módulos de E/S, iKVM opcional e um segundo CMC opcional e redundante, além de fornecer uma conexão de 10/100/1000 Mb à rede externa de gerenciamento.
Recursos da lâmina Recursos de desempenho PowerEdge M905 • Quatro processadores de dois ou quatro núcleos AMD™ Opteron™ série 8000. • Mínimo de 8 GB em módulos de memória DDR2 de 677 MHz, que podem ser atualizados para no máximo 192 GB com a instalação de pares de módulos de 1 GB, 2 GB, 4 GB ou 8 GB nos 24 soquetes dos módulos de memória da placa de sistema das lâminas.
PowerEdge M605 • Um ou dois processadores de dois ou quatro núcleos AMD Opteron série 2000. • Mínimo de 1 GB em módulos de memória DDR2 de 677 MHz ou 800 MHz, que podem ser atualizados para no máximo 64 GB com a instalação de pares de módulos de 512 MB, 1 GB, 2 GB, 4 GB ou 8 GB nos oito soquetes dos módulos de memória da placa de sistema das lâminas. A lâmina também oferece suporte para sobressalência de memória.
• Quatro portas Ethernet de 1 GB são compatíveis com dois controladores Broadcom de duas portas integrados 5709S (PowerEdge M805 e M905) ou duas portas Ethernet de 1 GB compatíveis com dois controladores Broadcom 5708S integrados (PowerEdge M600 e M605). Mecanismo de descarregamento TCP/IP (TOE) e suporte de inicialização iSCSI são compatíveis. Para obter uma lista completa de recursos do sistema, consulte “Especificações técnicas” na página 59.
Sistemas operacionais admitidos • Microsoft® Windows Server™ 2003, edições Web, Standard e Enterprise (x86 de 32 bits) com SP2 • Microsoft Windows Server 2003, edições Standard, Enterprise e DataCenter (x64) SP1, SP2 • Microsoft Windows Server 2003 R2, edições Standard e Enterprise com SP1, SP2 (x86 de 32 bits).
• O Manual do proprietário de hardware fornece informações sobre os recursos do sistema e descreve como solucionar problemas do sistema e instalar ou substituir seus componentes. Esse documento pode ser encontrado nos CDs que acompanham o sistema ou no site support.dell.com (em inglês). • O Dell Chassis Management Controller User’s Guide (Guia do usuário do Controlador de Gerenciamento do Chassi da Dell) fornece informações detalhadas sobre a utilização dos recursos de gerenciamento remoto do sistema.
Instalação e configuração ADVERTÊNCIA: Antes de executar o seguinte procedimento, leia e siga as instruções de segurança e as informações importantes sobre regulamentação fornecidas com o sistema. Para obter informações adicionais sobre as práticas recomendadas de segurança, consulte www.dell.com/regulatory_compliance. Esta seção descreve as etapas necessárias para a configuração do sistema pela primeira vez. Remoção do sistema da embalagem Remova o sistema da embalagem e identifique cada item.
Instale as lâminas Deslize os módulos da caixa da esquerda para a direita, começando da parte superior. Quando a lâmina estiver instalada com segurança, a alça retorna para a posição fechada. Conecte os módulos CMC e KVM Conecte os cabos serial e de rede do sistema de gerenciamento ao módulo DRAC/MC. Se um segundo módulo CMC opcional estiver instalado, conecte-o também. (Se o chassi tiver sido enviado com lâminas M805 ou M905 pré-instaladas, o firmware do CMC incluído será a versão 1.2 ou superior.
Conecte o sistema à energia Conecte os cabos de alimentação do sistema às fontes de alimentação. AVISO: Para evitar que os cabos de alimentação se desconectem acidentalmente, use o clipe plástico de cada fonte de alimentação para prender o cabo à fonte e a tira de velcro para prender o cabo à barra de alívio de tensão.
Ligue o sistema Pressione o botão liga/desliga da caixa. A luz indicadora de energia deverá se acender. Ligue as lâminas Pressione o botão liga/desliga de cada lâmina ou ligue as lâminas através do software de gerenciamento de sistemas.
Conclua a configuração do sistema operacional Caso tenha adquirido um sistema operacional pré-instalado, consulte a respectiva documentação fornecida com o sistema. Para instalar um sistema operacional pela primeira vez, consulte o Guia de instalação rápida. Certifique-se de que o sistema operacional esteja instalado antes de instalar qualquer hardware ou software que não tenha sido adquirido com o sistema.
Memória (continuação) Capacidades dos módulos de memória 512 MB (PowerEdge M605 e M600), 1 GB, 2 GB, 4 GB ou 8 GB RAM mínima Dois módulos de memória por processador PowerEdge M905 8 GB (oito módulos de memória de 1 GB) PowerEdge M805 4 GB (quatro módulos de memória de 1 GB) PowerEdge M600, M605 1 GB (dois módulos de memória de 512 MB) RAM máxima PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M600, M605 64 GB Unidades Unidades de disco rígido PowerEdge M805, M905 Uma ou duas unidades
Conectores Externos USB PowerEdge M805, M905 Três de 4 pinos, compatível com USB 2.0 PowerEdge M600, M605 Dois de 4 pinos, compatível com USB 2.
Características físicas (continuação) Largura 5 cm (2 pol.) Profundidade 48,6 cm (19,2 pol.) Peso (configuração máxima) 5,2 kg a 6,4 kg (11,5 lb a 14 lb) Bateria Bateria das lâminas Pilha do tipo moeda, de íon de lítio, CR 2032 de 3,0 V Especificações da caixa do sistema Características físicas Altura 44,0 cm (17,3 pol.) Largura 44,7 cm (17,6 pol.) Profundidade 75,5 cm (29,7 pol.
Módulo Avocent iKVM opcional Conectores traseiros acessíveis externamente USB Dois conectores de 4 pinos compatíveis com USB 2.0 para teclado e mouse Porta ACI RJ-45 Vídeo VGA de 15 pinos Módulo controlador de gerenciamento do chassi Conectores acessíveis externamente Gerenciamento remoto Duas portas RJ-45 10/100/1000 Mb para controlador de acesso remoto Ethernet integrado.
Especificações do módulo de E/S Módulo de comutação PowerConnect M6220 Ethernet Conectores acessíveis externamente Ethernet de 10/100/1000 Mbps Quatro portas RJ-45 autonegociáveis Serial Um conector de 4 pinos USB 2.0 tipo A. Deve ser usado um conector USB tipo A para que o adaptador DB9 se conecte ao terminal. Módulos opcionais Dois compartimentos opcionais.
Ambientais NOTA: Para obter informações adicionais sobre os valores ambientais para configurações de sistema específicas, visite o site dell.com/environmental_datasheets (em inglês) O sistema não se destina à utilização em escritórios. Temperatura De funcionamento 10 °C a 35 °C (50 °F a 95 °F). NOTA: Diminua a temperatura máxima em 1 °C (1,8 °F) para cada 300 m (985 pés), acima de 900 m (2955 pés) de altitude. De armazenamento -40 °C a 65 °C (-40 °F a 149 °F).
66 Primeiros passos com o sistema
Dell™ PowerEdge™ M905, M805, M605 y M600 Procedimientos iniciales con el sistema
Notas, avisos y precauciones NOTA: Una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. AVISO: Un AVISO indica la posibilidad de daños en el hardware o la pérdida de datos, e informa de cómo evitar el problema. PRECAUCIÓN: Un mensaje de PRECAUCIÓN indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin previo aviso. © 2008 Dell Inc. Todos los derechos reservados.
Características del sistema En esta sección se describen las características principales del hardware y el software del sistema. También se ofrece información sobre otros documentos que puede necesitar para instalar el sistema y sobre cómo obtener asistencia técnica.
Características de administración de sistemas • Una controladora de administración del chasis (CMC), que proporciona varias funciones básicas de administración de sistemas: – 70 Administración de energía del alojamiento y administración térmica: • La CMC supervisa los requisitos de alimentación del sistema y es compatible con el modo opcional de activación dinámica de la fuente de alimentación para que la CMC pueda activar fuentes de alimentación o colocarlas en modo de espera de forma dinámica, según
La CMC cuenta con dos puertos Ethernet. El puerto “Gb1” se utiliza para la conexión a la red de administración externa. El puerto “Stack” permite conectar secuencialmente CMC de alojamientos adyacentes. Un conmutador Ethernet de 24 puertos proporciona una comunicación interna a 100 Mb con los módulos de alta densidad, los módulos de E/S, un módulo iKVM opcional y una segunda CMC redundante opcional, y proporciona una conexión de 10/100/1000 Mb a la red de administración externa.
Características del módulo de alta densidad Características de rendimiento PowerEdge M905 • Cuatro procesadores AMD™ Opteron™ serie 8000 de dos o cuatro núcleos. • Un mínimo de 8 GB de módulos de memoria DDR2 a 677 MHz, ampliables a un máximo de 192 GB mediante la instalación de pares de módulos de 1 GB, 2 GB, 4 GB o 8 GB en los 24 zócalos de módulo de memoria de la placa base del módulo de alta densidad.
PowerEdge M600 • Uno o dos procesadores Intel® Xeon® de dos o cuatro núcleos. • Un mínimo de 1 GB de módulos de memoria FBD a 677 MHz, ampliables a un máximo de 64 GB mediante la instalación de pares de módulos de 512 MB, 1 GB, 2 GB, 4 GB o 8 GB en los ocho zócalos de módulo de memoria de la placa base del módulo de alta densidad.
• Un subsistema de vídeo integrado compatible con VGA con una controladora de vídeo ATI RN50. Este subsistema de vídeo contiene 32 MB de memoria de vídeo SDRAM (no ampliable). La resolución máxima es de 1 280 x 1 024 con 65 000 colores (no entrelazados).
• Software y documentación de administración de sistemas. El software de administración de sistemas se utiliza para administrar y supervisar los módulos de alta densidad individualmente, así como el sistema en su totalidad, incluidos todos los módulos de alta densidad, módulos de conmutador de red, fuentes de alimentación y ventiladores. El software de administración de sistemas administra el sistema de forma local y remota en una red.
Otra información útil PRECAUCIÓN: Consulte la información sobre normativas y seguridad suministrada con el sistema. La información sobre la garantía puede estar incluida en este documento o constar en un documento aparte. 76 • La Guía de configuración proporciona información sobre cómo configurar el alojamiento del sistema y los módulos de alta densidad.
• Algunas veces, con el sistema se incluyen actualizaciones que describen los cambios realizados en el sistema, en el software o en la documentación. NOTA: Compruebe si hay actualizaciones en support.dell.com y, si las hay, léalas antes de proceder a la instalación, puesto que a menudo sustituyen la información contenida en otros documentos.
Instalación del sistema en un rack Después de leer las instrucciones de seguridad incluidas en la documentación del sistema relativa a la instalación del rack, instale el sistema en el rack. Consulte la documentación de instalación del rack para obtener instrucciones sobre la instalación del sistema en un rack. Para obtener pautas sobre alimentación y refrigeración, consulte información sobre la herramienta de planificación de la capacidad del rack (rack capacity planner) en www.dell.com.
Conexión de los módulos CMC y KVM Conecte el cable serie y el cable de red del sistema de administración al módulo CMC. Si va a instalar un segundo módulo CMC opcional, conéctelo también. Si con el chasis se incluyen módulos de alta densidad M805 o M905 preinstalados, la versión del firmware de la CMC será 1.2 o superior. Conecte el teclado, el ratón y el monitor al módulo iKVM opcional.
Conexión del sistema a la alimentación Conecte los cables de alimentación del sistema a las fuentes de alimentación. AVISO: Para evitar que los cables de alimentación se desconecten accidentalmente, utilice el gancho de plástico de cada fuente de alimentación para fijar el cable a la fuente de alimentación, y utilice la tira de velcro para fijar el cable a la barra liberadora de tensión.
Encendido de los módulos de alta densidad Presione el botón de encendido de cada módulo de alta densidad o encienda los módulos mediante el software de administración de sistemas.
Finalización de la configuración del sistema operativo Si ha adquirido un sistema operativo preinstalado, consulte la documentación del sistema operativo que se suministra con el sistema. Para instalar un sistema operativo por primera vez, consulte la Guía de instalación rápida. Asegúrese de que el sistema operativo está instalado antes de instalar hardware o software no adquirido con el sistema.
Memoria (continuación) Capacidades del módulo de memoria 512 MB (PowerEdge M605 y M600), 1 GB, 2 GB, 4 GB u 8 GB RAM mínima Dos módulos de memoria por procesador PowerEdge M905 8 GB (ocho módulos de memoria de 1 GB) PowerEdge M805 4 GB (cuatro módulos de memoria de 1 GB) PowerEdge M600 y M605 1 GB (dos módulos de memoria de 512 MB) RAM máxima PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M600 y M605 64 GB Unidades Unidades de disco duro PowerEdge M805 y M905 Una o dos unidades de di
Conectores Externos USB PowerEdge M805 y M905 Tres de 4 patas compatibles con USB 2.0 PowerEdge M600 y M605 Dos de 4 patas compatibles con USB 2.
Características físicas (continuación) Profundidad 48,6 cm Peso (configuración máxima) De 5,2 a 6,4 kg Batería Batería del módulo de alta densidad Batería de tipo botón litio-ion CR2032 de 3 V Especificaciones del alojamiento del sistema Características físicas Altura 44,0 cm Anchura 44,7 cm Profundidad 75,5 cm Peso (configuración máxima) 178,3 kg Peso (vacío) 44,6 kg Módulo de fuente de alimentación Fuente de alimentación de CA/CC (por fuente de alimentación) Potencia 2 360 W Conector En
Módulo iKVM Avocent opcional Conectores posteriores de acceso externo USB Dos conectores de 4 patas compatibles con USB 2.
Especificaciones del módulo de E/S Módulo de conmutador Ethernet PowerConnect M6220 Conectores de acceso externo Ethernet 10/100/1000 Mbps Cuatro puertos RJ-45 de negociación automática Serie Un conector A de tipo USB 2.0 de 4 patas. Para la conexión al terminal, se debe utilizar un adaptador de A de tipo USB a DB9. Módulos opcionales Dos compartimientos opcionales.
Especificaciones ambientales NOTA: Para obtener información adicional sobre medidas ambientales relativas a configuraciones de sistema específicas, vaya a dell.com/environmental_datasheets. El sistema no se debe usar en un entorno de oficina. Temperatura En funcionamiento De 10 a 35 °C NOTA: Por encima de los 900 m, la temperatura máxima se reduce en 1 °C por cada 300 m.