Dell™ PowerEdge™ M1000e, M910, M905, M805, M710HD, M710, M610x, M610, M605, and M600 Getting Started With Your System Guide de mise en route Primeiros passos com o sistema Procedimientos iniciales con el sistema
Dell™ PowerEdge™ M1000e, M910, M905, M805, M710HD, M710, M610x, M610, M605, and M600 Getting Started With Your System Model BMX01, HHB Series, FHB Series
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2010 Dell Inc. All rights reserved.
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. This section describes the steps required to set up your system for the first time. Unpack the System Unpack your system and identify each item. Installing the Rails and System in a Rack Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your enclosure.
Installing the Blades Beginning at the top, slide the modules into the enclosure from left to right. When the blade is securely installed, the handle returns to the closed position. Connecting the CMC and KVM Modules Connect the serial cable and network cable(s) from the management system to the CMC module. If a second, optional CMC module is installed, connect it as well. Connect the keyboard, mouse, and monitor to the optional iKVM module.
Connecting the System to Power Connect the system’s power cables to the system power supplies. CAUTION: To prevent the power cables from being disconnected accidentally, use the plastic clip on each power supply to secure the power cable to the power supply, and use the Velcro strap to secure the cable to the strain-relief bar. Plug the other end of the power cables into a power distribution unit (PDU). CAUTION: Do not plug the power cables directly into a power outlet; you must use a PDU.
Turning On the System Press the power button on the enclosure. The power indicator should light. NOTE: Once you have connected the system to the power supplies, there may be a minimal delay before you can turn on your system. Turning On the Blades Press the power button on each blade, or power on the blades using the systems management software.
Complete the Operating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system. Supported Operating Systems Operating System M710HD M910 Citrix® XenServer 5.
Operating System M710HD M910 Microsoft Windows Web Server 2008 (x64) Edition with SP2 M905 M805 M710 M610 M610x Microsoft Windows Server 2008 R2 Standard, Enterprise, and Datacenter (x64) Editions Microsoft Windows Server 2003 Standard and Enterprise Editions Microsoft Windows Server 2003 Web Edition Microsoft Windows Server 2003 Standard Enterprise, and Web Editions with SP1 and later Microsoft Windows Server 2003 R2 Standard and Enterprise (x86) Editions
Operating System M710HD Red Hat Enterprise Linux AS and ES (version 4.8) (x86) M910 M905 M805 Red Hat Enterprise Linux AS and ES (version 4.8) (x86_64) Red Hat Enterprise Linux (version 5.0) (x86) Red Hat Enterprise Linux (version 5.0) (x86_64) Red Hat Enterprise Linux (version 5.2) (x86) M710 M610 M610x M605 Red Hat Enterprise Linux (version 5.5) (x86) Red Hat Enterprise Linux (version 5.
Other Information You May Need WARNING: Before performing the following procedure, review the safety instructions that came with the system. • The Configuration Guide provides information on configuring the system enclosure and the blades. • Rack Installation Instructions included with your rack solution describes how to install your system into a rack.
Technical Specifications Blade Specifications Processor Processor type PowerEdge M910 Two or four Intel® Xeon® 7000 series processors (up to eight-core processors) PowerEdge M905 Four dual- or quad-core AMD® Opteron® 8000 series processors PowerEdge M805 Two dual- or quad-core AMD Opteron 2000 series processors PowerEdge M710HD, M710, M610, M610x One or two dual-, quad-, or six-core Intel Xeon 5000 series processors PowerEdge M605 One or two dual- or quad-core AMD Opteron 2000 series processors Po
Memory (continued) Memory module sockets PowerEdge M910 32 240-pin sockets PowerEdge M905 24 240-pin sockets PowerEdge M805 16 240-pin sockets PowerEdge M710HD 18 240-pin sockets PowerEdge M710 18 240-pin sockets PowerEdge M610x, M610 12 240-pin sockets PowerEdge M605, M600 Eight 240-pin sockets Memory module capacities PowerEdge M910 1 GB, 2 GB, 4 GB, 8 GB, and 16 GB RDIMMs PowerEdge M905, M805, 1 GB, 2 GB, 4 GB, and 8 GB PowerEdge M710HD 1 GB, 2 GB, 4 GB, 8 GB, and 16 GB RDIMMs and LV D
Memory (continued) Maximum RAM PowerEdge M910 512 GB PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M710HD 144 GB (dual-rank DIMMs) or 192 GB (quad-rank DIMMs) PowerEdge M710 192 GB (12 16-GB RDIMMs); 36 GB (18 2-GB UDIMMs) PowerEdge M610, M610x 192 GB (12 16-GB RDIMMs); 24 GB (12 2-GB UDIMMs) PowerEdge M600, M605 64 GB Drives Hard Drives PowerEdge M910 Up to two 2.5-inch SAS hard-disk drives support through value RAID or performance RAID storage card. or Up to two 2.
Drives (continued) PowerEdge M600, M610x, M610 One 2.5-inch SATA hard-disk drive support through non-RAID, value RAID, or performance RAID storage card. or Two 2.5-inch SATA hard-disk drives support through value RAID or performance RAID storage card. or One solid-state disk (SSD) hard drive support through non-RAID storage card. or Up to two SAS hard-disk drives support through value RAID or performance RAID storage card.
Connectors (continued) Internal Internal Secure Digital (SD) module (PowerEdge M910, M805, M905, M710HD, M710, M610x, M610) One optional flash memory card slot with the internal SD module. Internal Secure Digital (SD) vFlash module (PowerEdge M910, M710HD, M710, M610x, M610) One optional vFlash memory card slot for use with the iDRAC Enterprise support. USB key (PowerEdge M910, M710HD, M710, M610x, M610) One internal USB key connector.
Mezzanine Cards (continued) PowerEdge M610x, M610 Up to two PCIe Gen 2 x8 mezzanine card slots, supporting dual-port Gb Ethernet, 10 Gb Ethernet, FC8 or FC4 (M610 only) Fibre Channel, or 4x DDR Infiniband mezzanine cards. PowerEdge M605, M600 Up to two PCIe x8 mezzanine card slots, supporting dual-port Gb Ethernet, 10 Gb Ethernet, FC8 or FC4 Fibre Channel, or 4x DDR Infiniband mezzanine cards.
Physical (continued) PowerEdge M905, M805, M710, M610x Height 38.5cm (15.2 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 11.1 kg (24.5 lb) PowerEdge M710HD Height 18.9 cm (7.4 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 7.4 kg (16.3 lb) PowerEdge M605, M600 Height 18.9 cm (7.4 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 5.2–6.4 kg (11.5–14.0 lb) Battery NVRAM backup battery CR 2032 3.
System Enclosure Specifications Physical Height 44.0 cm (17.3 in) Width 44.7 cm (17.6 in) Depth 75.5 cm (29.7 in) Weight (maximum configuration) 178.3 kg (392.2 lb) Weight (empty) 44.6 kg (98.1 lb) Power Supply Module AC/DC power supply (per power supply) Wattage 2360 W and 2700 W Connector IEC C20 Heat dissipation 1205 BTU/hr.
Chassis Management Controller Module Externally accessible connectors Remote management Two dedicated 10/100/1000 Mb RJ-45 (for integrated Ethernet remote access controller). Gb port connects to the external management network. STK port allows CMCs in adjacent enclosures to be daisy chained. Serial 9-pin, DTE, 16550-compatible Video 15-pin VGA Battery CR 2032 3.0-V lithium ion coin cell Enclosure Control Panel Externally accessible connectors USB Two 4-pin, USB 2.
I/O Module Specifications For information about the I/O modules and pass-through modules supported on your enclosure, see the Dell PowerEdge M1000e Systems Configuration Guide at support.dell.com/manuals. Environmental NOTE: For additional information about environmental measurements for specific system configurations, see dell.com/environmental_datasheets. The system is not for use in an office environment. Temperature Operating 10° to 35°C (50° to 95°F) NOTE: Decrease the maximum temperature by 1°C (1.
Systèmes Dell™ PowerEdge™ M1000e, M910, M905, M805, M710HD, M710, M610x, M610, M605 et M600 Guide de mise en route Modèle BMX01, série HHB, série FHB
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque d'endommagement du matériel ou de perte de données en cas de non-respect des instructions. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessure corporelle ou de mort.
Installation et configuration AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous, lisez les consignes de sécurité fournies avec le système. Cette section décrit les étapes à exécuter lors de la configuration initiale du système. Déballage du système Sortez le système de son emballage et identifiez chaque élément.
Installation des serveurs lames Insérez les modules dans le châssis en commençant par le haut et en procédant de gauche à droite. Lorsqu'un serveur lame est correctement installé, la poignée revient en position fermée. Connexion des modules CMC et KVM Connectez le ou les câbles série et réseau entre le système de gestion et le module CMC. Si un second module CMC en option est installé, connectez-le également. Connectez le clavier, la souris et le moniteur au module iKVM en option.
Branchement du système sur le secteur Branchez les câbles d'alimentation du système aux blocs d'alimentation de celui-ci. PRÉCAUTION : Pour éviter que les câbles d'alimentation ne soient débranchés accidentellement, utilisez le clip en plastique situé sur chaque bloc d'alimentation pour y fixer le câble. Utilisez également la bande Velcro permettant de maintenir le câble sur la barre de retenue. Branchez l'autre extrémité des câbles d'alimentation dans une unité de distribution d'alimentation.
Mise sous tension du système Appuyez sur le bouton d'alimentation du châssis. Le voyant d'alimentation s'allume. REMARQUE : Lorsque vous avez connecté le système aux blocs d'alimentation, un court laps de temps peut s'écouler avant que vous ne puissiez mettre le système sous tension. Mise sous tension des serveurs lames Mettez chaque serveur lame sous tension en appuyant sur son bouton d'alimentation ou en utilisant le logiciel Systems Management Software.
Finalisation de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez la documentation connexe fournie avec le système. Pour une première installation du système d'exploitation, consultez la documentation relative à l'installation et à la configuration du système d'exploitation. Veillez à installer le système d'exploitation avant tout élément matériel ou logiciel acheté séparément.
Système d'exploitation M710HD M910 Microsoft Windows Server 2008 R2, éditions Standard, Enterprise et Datacenter (x64) M905 M805 M710 M610 M610x Microsoft Windows Server 2003, éditions Standard et Enterprise Microsoft Windows Server 2003, édition Web Microsoft Windows Server 2003, éditions Standard, Enterprise et Web, avec SP1 et version ultérieure Microsoft Windows Server 2003 R2, éditions Standard et Enterprise (x86) Microsoft Windows Server 2003, édit
Système d'exploitation M710HD Red Hat Enterprise Linux AS et ES (version 4.8) (x86_64) Red Hat Enterprise Linux (version 5.0) (x86) Red Hat Enterprise Linux (version 5.0) (x86_64) M910 M905 M805 M710 M610 M610x M605 Red Hat Enterprise Linux (version 5.2) (x86) Red Hat Enterprise Linux (version 5.5) (x86) Red Hat Enterprise Linux (version 5.
Autres informations utiles AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous, lisez les consignes de sécurité fournies avec le système. • Le Guide de configuration fournit des informations sur la configuration du châssis du système et des serveurs lames. • Le Guide d'installation du rack, fourni avec le rack, indique comment installer le système en rack.
Caractéristiques techniques Spécifications des serveurs lames Processeur Type de processeur PowerEdge M910 Deux ou quatre processeurs Intel® Xeon® série 7000 (processeurs huit cœurs disponibles) PowerEdge M905 Quatre processeurs AMD® Opteron® série 8000 double cœur ou quadruple cœur PowerEdge M805 Deux processeurs AMD Opteron série 2000 double cœur ou quadruple cœur PowerEdge M710HD, M710, M610, M610x Un ou deux processeurs Intel Xeon série 5000, à deux, quatre ou six cœurs PowerEdge M605 Un ou deu
Mémoire (suite) Connecteurs de barrettes de mémoire PowerEdge M910 32 connecteurs à 240 broches PowerEdge M905 24 connecteurs à 240 broches PowerEdge M805 16 connecteurs à 240 broches PowerEdge M710HD 18 connecteurs à 240 broches PowerEdge M710 18 connecteurs à 240 broches PowerEdge M610x, M610 12 connecteurs à 240 broches PowerEdge M605, M600 8 connecteurs à 240 broches Capacité des barrettes de mémoire PowerEdge M910 RDIMM de 1 Go, 2 Go, 4 Go, 8 Go et 16 Go PowerEdge M905, M805 1 Go, 2 Go
Mémoire (suite) RAM maximale PowerEdge M910 512 Go PowerEdge M905 192 Go PowerEdge M805 128 Go PowerEdge M710HD 144 Go (DIMM à double rangée) ou 192 Go (DIMM à quadruple rangée) PowerEdge M710 192 Go (12 RDIMM de 16 Go) ; 36 Go (18 UDIMM de 2 Go) PowerEdge M610, M610x 192 Go (12 RDIMM de 16 Go) ; 24 Go (12 UDIMM de 2 Go) PowerEdge M600, M605 64 Go Lecteurs Disques durs PowerEdge M910 Prise en charge d'un ou de deux disques durs SAS 2,5 pouces via valeur RAID ou adaptateur de stockage RAID hau
Lecteurs (suite) PowerEdge M600, M610x, M610 Prise en charge d'un disque dur SATA 2,5 pouces via valeur RAID, valeur non-RAID ou adaptateur de stockage RAID haute performance. ou Prise en charge de deux disques durs SATA 2,5 pouces via valeur RAID ou adaptateur de stockage RAID haute performance. ou Prise en charge d'un disque dur SSD (solid-state disk) via un adaptateur de stockage non-RAID.
Connecteurs Externe USB PowerEdge M910, M805, Trois connecteurs à 4 broches, compatibles USB 2.0 M905, M710 PowerEdge M710HD, M610x, M610, M605, M600 Deux connecteurs à 4 broches, compatibles USB 2.0 Interne Module SD (Secure Un logement pour carte mémoire flash, en option, Digital) interne (PowerEdge avec le module interne SD.
Cartes mezzanine PowerEdge M910 Jusqu'à quatre logements de carte mezzanine PCIe x8 2ème génération, prenant en charge des cartes mezzanine Gigabit Ethernet à double port, Ethernet 10 Go, Fibre Channel FC8 ou Infiniband. PowerEdge M905, M805 Jusqu'à quatre logements de carte mezzanine PCIe x8 1ère génération, prenant en charge des cartes mezzanine Gigabit Ethernet à double port, Ethernet 10 Go, Fibre Channel FC8 ou FC4 ou Infiniband DDR 4x.
Contrôleurs Ethernet intégrés PowerEdge M910, M905, M805, M710HD, M710 Quatre ports Ethernet avec prise en charge d'amorçage TOE et iSCSI, assurée par deux contrôleurs intégrés Ethernet Broadcom 5709S à double port. PowerEdge M610x, M610 Deux ports Ethernet avec prise en charge d'amorçage TOE et iSCSI, assurée par un contrôleur intégré Ethernet Broadcom 5709S à double port.
Physique (suite) PowerEdge M710HD Hauteur 18,9 cm (7,4 pouces) Largeur 5 cm (2 pouces) Profondeur 48,6 cm (19,2 pouces) Poids (configuration maximale) 7,4 kg (16,3 livres) PowerEdge M605, M600 Hauteur 18,9 cm (7,4 pouces) Largeur 5 cm (2 pouces) Profondeur 48,6 cm (19,2 pouces) Poids (configuration maximale) 5,2–6,4 kg (11,5–14 livres) Batterie Batterie de sauvegarde NVRAM Pile bouton au lithium CR 2032 (3 V) Spécifications du châssis Physique Hauteur 44 cm (17,3 pouces) Largeur 44,7 cm
Bloc d'alimentation Bloc d'alimentation en CA/CC (selon la tension en vigueur) Puissance 2360 W et 2700 W Connecteur IEC C20 Dissipation thermique 1205 BTU/h. maximum Appel de courant maximal Dans des conditions de ligne typiques et dans toute la gamme ambiante de fonctionnement du système, le courant d'appel peut atteindre 55 A par bloc d'alimentation pendant un maximum de 10 ms.
Panneau de commande du châssis Connecteurs accessibles de l'extérieur USB Deux connecteurs USB 2.
Environnement (suite) Tolérance maximale aux vibrations En fonctionnement 0,26 Grms avec un balayage de 10 à 350 Hz pendant 15 min Stockage 1,54 Grms avec un balayage de 10 à 250 Hz pendant 15 minutes Choc maximal En fonctionnement Une impulsion de choc de 41 G pendant un maximum de 2 ms sur l'axe z positif (une impulsion de chaque côté du système) Stockage Six chocs consécutifs de 71 G pendant un maximum de 2 ms en positif et négatif sur les axes x, y et z (une impulsion de chaque côté du système)
42 Guide de mise en route
Sistemas Dell™ PowerEdge™ M1000e, M910, M905, M805, M710HD, M710, M610x, M610 M605 e M600 Primeiros passos com o sistema Modelo BMX01, série HHB, série FHB
Notas, Avisos e Advertências NOTA: uma NOTA fornece informações importantes que o ajudam a utilizar melhor o computador. AVISO: um AVISO indica um potencial de danos ao hardware ou a perda de dados se as instruções não forem seguidas. ADVERTÊNCIA: uma ADVERTÊNCIA indica um potencial de danos à propriedade, de lesões corporais ou mesmo de morte. ____________________ As informações contidas neste documento estão sujeitas a alterações sem aviso prévio. © 2010 Dell Inc. Todos os direitos reservados.
Instalação e configuração ADVERTÊNCIA: antes de executar este procedimento, siga as instruções de segurança fornecidas com o sistema. Esta seção descreve as etapas necessárias para a configuração do sistema pela primeira vez. Remover o sistema da embalagem Remova o sistema da embalagem e identifique cada item. Como instalar os trilhos e o sistema no rack Monte os trilhos e instale o sistema no rack seguindo as instruções de segurança e as instruções de instalação do rack fornecidas com o sistema.
Como instalar as lâminas Deslize os módulos da caixa da esquerda para a direita, começando da parte superior. Quando a lâmina estiver instalada com segurança, a alça retorna para a posição fechada. Como conectar os módulos CMC e KVM Conecte os cabos serial e de rede do sistema de gerenciamento ao módulo CMC. Se um segundo módulo CMC opcional estiver instalado, conecte-o também. Conecte o teclado, o mouse e o monitor ao módulo iKVM opcional.
Como conectar o sistema à energia Conecte os cabos de alimentação do sistema às fontes de alimentação. AVISO: para evitar que os cabos de alimentação se desconectem acidentalmente, use o clipe plástico de cada fonte de alimentação para prender o cabo à fonte e a tira de velcro para prender o cabo à barra de alívio de tensão. Conecte a outra extremidade do cabo de alimentação a unidade de distribuição de energia (PDU).
Como ligar o sistema Pressione o botão liga/desliga da caixa. A luz indicadora de energia deverá se acender. NOTA: assim que você tiver conectado o sistema às fontes de alimentação, poderá haver uma demora mínima até que você possa ligar o sistema. Como ligar as lâminas Pressione o botão liga/desliga de cada lâmina ou ligue as lâminas através do software de gerenciamento de sistemas.
Concluir a instalação do sistema operacional Caso tenha adquirido um sistema operacional pré-instalado, consulte a respectiva documentação fornecida com o sistema. Para instalar um sistema operacional pela primeira vez, consulte a documentação de instalação e configuração do sistema operacional. Certifique-se de que o sistema operacional esteja instalado antes de instalar qualquer hardware ou software que não tenha sido adquirido com o sistema.
Sistema operacional M710HD M910 Microsoft Windows Server 2008 R2, edições Standard, Enterprise e Datacenter (x64) M905 M805 M710 M610 M610x Microsoft Windows Server 2003, edições Standard e Enterprise Microsoft Windows Server 2003, edição Web Microsoft Windows Server 2003, edições Standard Enterprise e Web com SP1 e posterior Microsoft Windows Server 2003 R2, edições Standard e Enterprise (x86) Microsoft Windows Server 2003, edições Standard e Enterprise
Sistema operacional M710HD Red Hat Enterprise Linux ES (versão 5) (x86) Red Hat Enterprise Linux ES (versão 5) (x86_64) M910 M905 M805 Red Hat Enterprise Linux (versão 5.2) (x86) M710 M610 M610x Red Hat Enterprise Linux (versão 5.2) (x86) Red Hat Enterprise Linux (versão 5.2) (x86_64) SUSE® Linux Enterprise Server 9 SP3 (x86_64) SUSE Linux Enterprise Server 10 (x86_64).
Outras informações úteis ADVERTÊNCIA: antes de executar este procedimento, siga as instruções de segurança fornecidas com o sistema. • O Configuration Guide (Guia de configuração) fornece informações sobre como configurar a caixa e as lâminas do sistema. • As instruções para instalação em rack incluídas com o rack descrevem como instalar o sistema em racks.
Especificações técnicas Especificações da lâmina Processador Tipo de processador PowerEdge M910 Dois ou quatro processadores Intel® Xeon® da série 7000 (processadores de até oito núcleos) PowerEdge M905 Quatro processadores de dois ou quatro núcleos AMD® Opteron® Série 8000 PowerEdge M805 Dois processadores de dois ou quatro núcleos AMD Opteron Série 2000 PowerEdge M710HD, M710, M610, M610x Um ou dois processadores de dois, quatro ou seis núcleos Intel Xeon série 5000 PowerEdge M605 Um ou dois proc
Memória (continuação) PowerEdge M710, M610, M610x DIMMs (UDIMMs) sem buffer ou DIMMs (RDIMMs) registrados com single-ranked (face simples) ou dual-ranked (face dupla) DDR3 de 800, 1066 ou 1333 MHz ou DIMMs (UDIMMs) sem buffer ou DIMMs (RDIMMs) registrados com quad-ranked (face quádrupla) DDR3 de 800 ou 1066 MHz PowerEdge M600 Módulos de memória FBD ajustados para operação em 677 MHz Soquetes de módulos de memória PowerEdge M910 32 soquetes de 240 pinos PowerEdge M905 24 soquetes de 240 pinos PowerEd
Memória (continuação) Mínimo de RAM PowerEdge M910 4 GB PowerEdge M905 8 GB (oito módulos de memória de 1 GB) PowerEdge M805 4 GB (quatro módulos de memória de 1 GB) PowerEdge M710D 4 GB PowerEdge M710, M610x, M610 Um módulo de memória de 1 GB (sistemas com um processador) ou dois módulos de memória de 1 GB (sistemas com dois processadores) PowerEdge M600, M605 1 GB (dois módulos de memória de 512 MB) Máximo de RAM PowerEdge M910 512 GB PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge
Unidades Unidades de disco rígido 56 PowerEdge M910 Até duas unidades de disco rígido SAS de 2,5 pol, suporte via cartão de armazenamento RAID de desempenho ou RAID de valor. ou Até duas unidades de disco rígido de SSD de 2,5 pol, suporte via cartão de armazenamento RAID de desempenho ou RAID de valor. PowerEdge M905, M805 Até duas unidades de disco rígido SAS de 2,5 pol, suporte via cartão de armazenamento RAID de desempenho ou RAID de valor.
Unidades (continuação) PowerEdge M605 Suporte para até duas unidades de disco rígido SATA via cartão de armazenamento RAID de desempenho ou RAID de valor. ou Suporte para até duas unidades de disco rígido de SSD via cartão de armazenamento não-RAID. ou Suporte para até duas unidades de disco rígido SAS via cartão de armazenamento RAID de desempenho ou RAID de valor. NOTA: para todos os sistemas modulares, as unidades de disco rígido SAS e SATA não podem ser misturadas em uma lâmina.
Conectores (continuação) Internos Módulo SD (Secure Digital) interno (PowerEdge M910, M805, M905, M710HD, M710, M610x, M610) Um slot de cartão de memória flash opcional com o módulo SD interno. Módulo vFlash SD (Secure Digital) interno (PowerEdge M910, M710HD, M710, M610x, M610) Um slot de placa de memória VFlash opcional para uso com o suporte iDRAC para empresas. Chave USB (PowerEdge M910, M710HD, M710, M610x, M610) Um soquete interno de chave USB.
Placas para mezanino (continuação) PowerEdge M710 Até quatro slots de placa PCIe Gen 2 (três trilhas de x8 e uma trilha de x4 de largura), com suporte a placas Gb Ethernet de dois portas, 10 Gb Ethernet, FC8 ou FC4 Fibre Channel ou 4x DDR Infiniband para mezanino. PowerEdge M610x, M610 Até dois slots de placa PCIe Gen 2 x8 para mezanino, com suporte a placas Gb Ethernet de duas portas, 10 Gb Ethernet, FC8 ou FC4 (somente para o M610) Fibre Channel ou 4x DDR Infiniband para mezanino.
Características físicas PowerEdge M910 Altura 38,5 cm (15,2 pol.) Largura 5 cm (2 pol.) Profundidade 48,6 cm (19,2 pol.) Peso (com a configuração máxima) 13,1 kg (29 lb) PowerEdge M905, M805, M710, M610x Altura 38,5 cm (15,2 pol.) Largura 5 cm (2 pol.) Profundidade 48,6 cm (19,2 pol.) Peso (com a configuração máxima) 11,1 kg (24,5 lb) PowerEdge M710HD Altura 18,9 cm (7,4 pol.) Largura 5 cm (2 pol.) Profundidade 48,6 cm (19,2 pol.
Especificações da caixa do sistema Características físicas Altura 44,0 cm (17,3 pol.) Largura 44,7 cm (17,6 pol.) Profundidade 75,5 cm (29,7 pol.) Peso (com a configuração máxima) 178,3 kg (392,2 lb) Peso (vazio) 44,6 kg (98,1 lb) Módulo da fonte de alimentação Fonte de alimentação CA/CC (por fonte de alimentação) Potência 2.360 W e 2.700 W Conector IEC C20 Dissipação de calor 1205 BTU/h.
Módulo controlador de gerenciamento do chassi Conectores acessíveis externamente Gerenciamento remoto Duas portas RJ-45 10/100/1000 Mb (para controlador de acesso remoto Ethernet integrado). A porta Gb conecta-se com a rede de gerenciamento externa. A porta STK permite que os CMCs em caixas adjacentes sejam conectados em margarida.
Especificações do módulo de E/S Para obter informações sobre os módulos de E/S e de passagem compatíveis com o compartimento, consulte o guia Dell PowerEdge M1000e Systems Configuration Guide no endereço support.dell.com/manuals (em inglês). Ambientais NOTA: para obter informações adicionais sobre os valores ambientais para configurações de sistema específicas, visite o site dell.com/environmental_datasheets. O sistema não se destina à utilização em escritórios.
64 Primeiros passos com o sistema
Dell™ PowerEdge™ M1000e, M910, M905, M805, M710HD, M710, M610x, M610, M605 y M600 Procedimientos iniciales con el sistema Modelo BMX01, serie HHB, serie FHB
Notas, precauciones y avisos NOTA: Una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. PRECAUCIÓN: Un mensaje de PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos si no se siguen las instrucciones. AVISO: Un mensaje de AVISO indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin previo aviso. © 2010 Dell Inc. Todos los derechos reservados.
Instalación y configuración AVISO: Antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. En esta sección se describen los pasos necesarios para configurar el sistema por primera vez. Desembalaje del sistema Desembale el sistema e identifique cada elemento. Instalación de los rieles y del sistema en un rack Monte los rieles e instale el sistema en el rack siguiendo las instrucciones de seguridad y de instalación del rack incluidas con el alojamiento.
Instalación de los módulos de alta densidad Empezando por la parte superior, inserte los módulos en el alojamiento de izquierda a derecha. Una vez que el módulo de alta densidad esté bien instalado, el asa volverá a la posición de cierre. Conexión de los módulos CMC y KVM Conecte el cable serie y los cables de red del sistema de administración al módulo CMC. Si va a instalar un segundo módulo CMC opcional, conéctelo también. Conecte el teclado, el ratón y el monitor al módulo iKVM opcional.
Conexión del sistema a la alimentación Conecte los cables de alimentación del sistema a las fuentes de alimentación. PRECAUCIÓN: Para evitar que los cables de alimentación se desconecten accidentalmente, utilice el gancho de plástico de cada fuente de alimentación para fijar el cable a la fuente de alimentación, y utilice la tira de velcro para fijar el cable a la barra liberadora de tensión. Enchufe el otro extremo de los cables de alimentación en la unidad de distribución de alimentación (PDU).
Encendido del sistema Presione el botón de encendido del alojamiento. El indicador de alimentación debería encenderse. NOTA: Después de conectar el sistema a las fuentes de alimentación, puede producirse una pequeña demora antes de poder encender el sistema. Encendido de los módulos de alta densidad Presione el botón de encendido de cada módulo de alta densidad o encienda los módulos mediante el software de administración de sistemas.
Instalación del sistema operativo Si ha adquirido un sistema operativo preinstalado, consulte la documentación del sistema operativo que se suministra con el sistema. Para instalar un sistema operativo por primera vez, consulte la documentación de instalación y configuración del sistema operativo. Asegúrese de que el sistema operativo esté instalado antes de instalar hardware o software no adquiridos con el sistema. Sistemas operativos admitidos Sistema operativo M710HD M910 Citrix® XenServer 5.
Sistema operativo M710HD M910 Microsoft Windows Web Server 2008 (x64) Edition con SP2 M905 M805 M710 M610 M610x Microsoft Windows Server 2008 R2 Standard, Enterprise, y Datacenter (x64) Edition Microsoft Windows Server 2003 Standard y Enterprise Edition Microsoft Windows Server 2003 Web Edition Microsoft Windows Server 2003 Standard Enterprise, y Web Edition con SP1 y posteriores Microsoft Windows Server 2003 R2 Standard y Enterprise (x86) Edition
Sistema operativo M710HD Red Hat Enterprise Linux AS y ES (versión 4.8) (x86) M910 M905 M805 Red Hat Enterprise Linux AS y ES (versión 4.8) (x86_64) Red Hat Enterprise Linux (versión 5.0) (x86) Red Hat Enterprise Linux (versión 5.0) (x86_64) Red Hat Enterprise Linux (versión 5.2) (x86) M710 M610 M610x M605 Red Hat Enterprise Linux (versión 5.5) (x86) Red Hat Enterprise Linux (versión 5.
Otra información útil AVISO: Antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. • La Guía de configuración proporciona información sobre cómo configurar el alojamiento del sistema y los módulos de alta densidad. • En las Instrucciones de instalación del rack incluidas con la solución de rack se describe cómo instalar el sistema en un rack.
Información de la NOM (sólo para México) La información que se proporciona a continuación aparece en el dispositivo descrito en este documento, en cumplimiento de los requisitos de la Norma Oficial Mexicana (NOM): Importador: Número de modelo: Voltaje de alimentación: Frecuencia: Consumo eléctrico: BMX01 200–240 V CA 50/60 Hz 43 A Importador: Número de modelo: Voltaje de alimentación: Consumo eléctrico: FHB 12 V CC 75 A Importador: Número de modelo: Voltaje de alimentación: Consumo eléctrico: HHB 12
Especificaciones técnicas Especificaciones del módulo de alta densidad Procesador Tipo de procesador PowerEdge M910 Dos o cuatro procesadores Intel® Xeon® serie 7000 (procesadores de hasta ocho núcleos) PowerEdge M905 Cuatro procesadores AMD® Opteron® serie 8000 de dos o cuatro núcleos PowerEdge M805 Dos procesadores AMD Opteron serie 2000 de dos o cuatro núcleos PowerEdge M710HD, M710, M610 y M610x Uno o dos procesadores Intel Xeon serie 5000 de dos, cuatro o seis núcleos PowerEdge M605 Uno o dos
Memoria (continuación) Zócalos de módulo de memoria PowerEdge M910 32 zócalos de 240 patas PowerEdge M905 24 zócalos de 240 patas PowerEdge M805 16 zócalos de 240 patas PowerEdge M710HD 18 zócalos de 240 patas PowerEdge M710 18 zócalos de 240 patas PowerEdge M610x, M610 12 zócalos de 240 patas PowerEdge M605 y M600 8 zócalos de 240 patas Capacidades del módulo de memoria PowerEdge M910 RDIMM de 1 GB, 2 GB, 4 GB, 8 GB y 16 GB PowerEdge M905 y M805 1 GB, 2 GB, 4 GB y 8 GB PowerEdge M710HD 1
Memoria (continuación) RAM máxima PowerEdge M910 512 GB PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M710HD 144 GB (DIMM duales) o 192 GB (DIMM cuádruples) PowerEdge M710 192 GB (12 RDIMM de 16 GB) 36 GB (18 UDIMM de 2 GB) PowerEdge M610, M610x 192 GB (12 RDIMM de 16 GB) 24 GB (12 UDIMM de 2 GB) PowerEdge M600 y M605 64 GB Unidades Unidades de disco duro 78 PowerEdge M910 Hasta dos unidades de disco duro SAS de 2,5 pulgadas.
Unidades (continuación) PowerEdge M710 Hasta cuatro unidades de disco duro SAS de 2,5 pulgadas. Compatibilidad mediante tarjeta de almacenamiento RAID básica o RAID de alto rendimiento. PowerEdge M600, M610x, M610 Compatibilidad con una unidad de disco duro SATA de 2,5 pulgadas mediante tarjeta de almacenamiento sin RAID, RAID básica o RAID de alto rendimiento.
Conectores Externos USB PowerEdge M910, M805, M905, M710 Tres de 4 patas compatibles con USB 2.0 PowerEdge M710HD, M610x, M610, M605, M600 Dos de 4 patas compatibles con USB 2.
Tarjetas intermedias (continuación) PowerEdge M710HD Hasta dos ranuras para tarjeta intermedia PCIe Gen 2 x8, que admiten tarjetas intermedias Ethernet Gb, 10Gb Ethernet, Fibre Channel FC8 o FC4, o Infiniband DDR 4x de dos y cuatro puertos. PowerEdge M710 Hasta cuatro ranuras para tarjeta intermedia PCIe Gen 2 (tres x8 y una x4), que admiten tarjetas intermedias Ethernet Gb, 10Gb Ethernet, Fibre Channel FC8 o FC4, o Infiniband DDR 4x de dos puertos.
Características físicas PowerEdge M910 Altura 38,5 cm Anchura 5 cm Profundidad 48,6 cm Peso (configuración máxima) 13,1 kg PowerEdge M905, M805, M710, M610x Altura 38,5 cm Anchura 5 cm Profundidad 48,6 cm Peso (configuración máxima) 11,1 kg PowerEdge M710HD Altura 18,9 cm Anchura 5 cm Profundidad 48,6 cm Peso (configuración máxima) 7,4 kg PowerEdge M605 y M600 Altura 18,9 cm Anchura 5 cm Profundidad 48,6 cm Peso (configuración máxima) 5,2 – 6,4 kg Batería Batería de reserva d
Especificaciones del alojamiento del sistema Características físicas Altura 44,0 cm Anchura 44,7 cm Profundidad 75,5 cm Peso (configuración máxima) 178,3 kg Peso (vacío) 44,6 kg Módulo de fuente de alimentación Fuente de alimentación de CA/CC (por fuente de alimentación) Potencia 2 360 W y 2 700 W Conector IEC C20 Disipación de calor 1 205 BTU/h (353 W) como máximo Corriente de conexión máxima En condiciones normales de línea y en todo el rango operativo del sistema, la corriente de la conexi
Módulo de controladora de administración del chasis Conectores de acceso externo Administración remota Dos RJ-45 10/100/1000 Mb dedicados (para una controladora de acceso remoto Ethernet integrada). El puerto Gb se conecta a la red de administración externa. El puerto STK permite la conexión secuencial de CMC de alojamientos adyacentes.
Especificaciones del módulo de E/S Para obtener información sobre los módulos de E/S y los módulos de paso a través que se admiten en su alojamiento, consulte el documento Sistemas Dell PowerEdge M1000e — Guía de configuración en support.dell.com/manuals. Especificaciones ambientales NOTA: Para obtener información adicional sobre medidas ambientales relativas a configuraciones del sistema específicas, vaya a dell.com/environmental_datasheets. Este sistema no debe utilizarse en un entorno de oficina.
86 Procedimientos iniciales con el sistema