Dell PowerEdge M1000e, M915, M910, M820, M710HD, M710, M620, M610x, M610, M520, and M420 Getting Started Guide Regulatory Model: BMX01, DWHH, HHB, FHB, and QHB Regulatory Type: DWHH Series, HHB Series, FHB Series, and QHB Series
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Information in this publication is subject to change without notice. © 2012 Dell Inc. All rights reserved.
Installation And Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the blade server or enclosure. Unpacking The System Unpack your blade server or enclosure and identify each item. Installing The Rails And Enclosure Figure 1. Installing the Enclosure in the Rack Assemble the rails and install the enclosure in the rack, following the safety instructions and the rack installation instructions provided with the enclosure.
Figure 2. Installing a Sleeve NOTE: Before you install or remove a sleeve from the enclosure, ensure that the top slot of the sleeve (Blade a) is empty. You can install a blade in the top slot (Blade a) after you install the sleeve in the enclosure. Remove the orange cover from the sleeve handle. Slide the sleeve into the enclosure and lift the sleeve handle to the top position to secure the sleeve in the enclosure.
Figure 4. Installing a Half-Height Blade NOTE: The above figure shows installation of a half-height blade. The procedure for installing a full-height blade is identical to installing a half-height blade. Beginning at the top, slide the blades into the enclosure from left to right. When the blade is securely installed, the blade handle returns to the closed position. Connecting The CMC And iKVM Modules Figure 5.
Connecting The System To Power Figure 6. Connecting Power to the System Connect the system’s power cables to the system power supplies. CAUTION: To prevent the power cables from being disconnected accidentally, use the plastic clip on each power supply to secure the power cable to the power supply, and use the strap to secure the power cable to the strainrelief bar. CAUTION: Do not plug the power cables directly into a power outlet; you must use a PDU.
Turning On The Blades Figure 8. Turning on a Blade Press the power button on each blade, or power on the blades using the systems management software. Complete The Operating System Setup If you purchased a preinstalled operating system, see the documentation associated with the operating system. To install an operating system for the first time, see the installation and configuration documentation for your operating system.
NOTE: Always check for updates on support.dell.com/manuals and read the updates first because they often supersede information in other documents. Obtaining Technical Assistance If you do not understand a procedure in this guide or if the system does not perform as expected, see your Owner’s Manual. Dell offers comprehensive hardware training and certification. See dell.com/training for more information. This service may not be offered in all locations.
Technical Specifications NOTE: For additional specifications, see your system Owner's Manual. Power — Blades Coin-cell battery 3 V CR2032 Lithium coin cell Power — Enclosure AC/DC power supply (per power supply module) Wattage 2360 W and 2700 W Connector IEC C20 Heat dissipation 1205 BTU/hr (maximum) Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less.
Physical — Blades PowerEdge M710 and M610x Height 38.5 cm (15.2 inch) Width 5 cm (2 inch) Depth 48.6 cm (19.2 inch) Weight (maximum) 11.1 kg (24.5 lb) PowerEdge M710HD and M620 Height 18.9 cm (7.4 inch) Width 5 cm (2 inch) Depth 48.6 cm (19.2 inch) Weight (maximum) 7.4 kg (16.3 lb) PowerEdge M610 Height 18.9 cm (7.4 inch) Width 5 cm (2 inch) Depth 48.6 cm (19.2 inch) Weight (maximum) 5.2 kg to 6.4 kg (11.5 lb to 14.0 lb) PowerEdge M520 Height 18.9 cm (7.
Physical — Enclosure Depth 75.5 cm (29.7 inch) Weight (maximum) 200.5 kg (442 lb) Weight (empty) 44.6 kg (98.1 lb) Environmental NOTE: For additional information about environmental measurements for specific system configurations, see dell.com/environmental_datasheets. Temperature Operating Continuous operation: 10 °C to 35 °C at 10% to 80% relative humidity (RH), with 26 °C max dew point. De-rate maximum allowable dry bulb temperature at 1 °C per 300 m above 900 m (1 °F per 550 ft).
