Dell PowerEdge Modüler Sistemler Donanım Kullanıcı El Kitabı
Notlar, Dikkat Edilecek Noktalar ve Uyarılar NOT: NOT, bilgisayarınızdan daha iyi şekilde yararlanmanıza yardımcı olacak önemli bilgiler verir. DİKKAT: DİKKAT, yönergelere uyulmadığında donanımın zarar görebileceğini veya veri kaybı olabileceğini belirtir. UYARI: UYARI, meydana gelebilecek olası maddi hasar, fiziksel yaralanma veya ölüm tehlikesi anlamına gelir. ____________________ Bu belgedeki bilgiler önceden bildirilmeksizin değiştirilebilir. © 2008-2011 Dell Inc. Tüm hakları saklıdır. Dell Inc.
İçerik 1 Sisteminiz Hakkında . . . . . . . . . . . . . Başlatma Sırasında Sistem Özelliklerine Erişim . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . 16 . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . . . . . 21 . . . . . . . . . . . . . 22 . . . . . . . 22 . . . . . . . . . . . . . . . . . . . 25 Sisteme Genel Bakış .
G/Ç Bağlantısı . . . . . . . . . . . . . . . . . . . . . G/Ç Modüllerinin Takılmasına Yönelik Kılavuzlar . . . . . . . . . . . . . . . . . . . . . Dört Bağlantı Noktalı Ağ Ek Kartında Otomatik Bağlantı Noktası Devre Dışı Bırakma (Sadece PowerEdge M710HD) Ara Kat Kartı . . . . 59 60 . . . . . . . . . Dell PowerConnect-KR 8024-k Anahtar . Dell M8428-k 10 Gb Yakınsak Ağ Anahtarı . . . . . . . . . . . Mellanox M2401G Infiniband Anahtar G/Ç Modülü . . . . . 79 . . . . . . . . . 81 . . . . . . 83 .
. . . . . . . . . . . . . . . 115 . . . . . . . 115 . . . . . . 115 . . . . . . . . . . . . . . . . . . 127 . . . . . . . . . . . . . . . . . . . 148 . . . . . . . . . . . . . . . . . 148 . . . . . . . . . . . . . . . . . . . 148 LCD Durum Mesajları Durum Mesajlarını Görüntüleme LCD Durum Mesajlarını Kaldırma Sistem Mesajları Uyarı Mesajları Tanılama Mesajları Uyarı Mesajları 2 Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi . . . . . . . . . . . . . . . . . . 149 . . .
. . . . . . . . . . . . 162 . . . . . . . . . . . . . . . . . . . 163 . . . . . . 164 Sistem Güvenlik Ekranı Çıkış Ekranı UEFI Önyükleme Yöneticisine Giriş UEFI Önyükleme Yöneticisi Ekranı . UEFI Önyükleme Ayarları Ekranı . . . . . . 164 . . . . . . 165 Sistem Yardımcı Programları Ekranı . . . . . 165 Sistem ve Kurulum Parolası Özellikleri . . . . 166 . . . . . . . . . . 166 Sistem Parolası Kullanma . Kurulum Parolasını Kullanma . . . . . . . . .
Sistem Belleği - PowerEdge M710 . . . . . . Sistem Belleği - PowerEdge M710HD . Sistem Belleği PowerEdge M610/M610x 203 . . . 209 . . . . . . . . . . . 214 Sistem Belleği - PowerEdge M605 . . . . . . 218 Sistem Belleği - PowerEdge M600 . . . . . . 224 . . . . . . . . . . . 227 . . . . . . . . . . 229 . . . . . . . . . . . 229 Bellek Modüllerini Takma Bellek Modüllerini Çıkarma Ara Kat Arabirim Kartı (Sadece PowerEdge M610x) Ara Kat Arabirim Kartının Çıkarılması . . . . 229 . . . . .
Ağ Ek Kartı/LOM Yükseltici Kart (Sadece PowerEdge M915 ve M710HD) . . . . 249 LOM Yükseltici Kartı Çıkarma . . . . . . . . . 249 LOM Yükseltici Kartını Takma . . . . . . . . . 250 Genişletme Kartları ve Genişletme Kartı Yükselticisi (Sadece PowerEdge M610x) . . . . . . . . . . . Genişletme Kartı Takma Yönergeleri . Genişletme Kartını Takma . . . . . 250 . . . . . . . . . . 251 Genişletme Kartının Çıkartılması . Genişletme-Kartı Yükseltici (Sadece PowerEdge M610x) . . . . . . 253 . . . . .
Sabit Sürücünün Sabit Sürücü Taşıyıcısından Çıkarılması . . . . . . . . . . 285 Sabit Sürücüyü Sabit Sürücü Taşıyıcısına Takma . . . . . . . . . . . . . . . 285 Video Denetleyicisi (Yalnızca PowerEdge M905, M805, M605 ve M600) . . . . . . . . . . . 287 . . . . . . . . . . . . . 289 . . . . . . . . . . . . . . . . . 291 . . . . . . . . . . . . 291 . . . . . . . . . . . . . 294 . . . . . . . . . . . 295 . . . 295 . . . . 296 . . . . . . . . . . . .
CMC Modülü . . . . . . . . . . . . . . . . . . . . . 307 . . . . . . . . . 307 Bir CMC modülünü Kaldırma . . . . . . . 308 . . . . . . . . . . . 309 . . . . . . . . . . . . . . . . . . . . 310 . . . . . . . . . . . 310 . . . . . . . . . . . . 310 . . . . . . . . . . . . . . . . . . . . 310 Bir G/Ç Modülünü Çıkarma . . . . . . . . . . 310 Bir G/Ç Modülünü Çıkarma . . . . . . . . . . 311 . . . . . . . . . . . . . . . . . . . 312 CMC Modülüne SD Kart Takma Bir CMC Modülü kurma. .
Harici Bağlantılara Yönelik Sorun Giderme . . . . . . . . . . . . . . . . . . . 324 Video'ya Yönelik Sorun Giderme . . . . . . . 324 Klavyeye Yönelik Sorun Giderme . . . . . . 325 . . . . . . . 325 . . . 326 . . . . . . 326 . . . . . 327 . . . . . . . . . . 328 . . . . . . . . . . . 329 Fareye Yönelik Sorun Giderme . USB Cihazlara Yönelik Sorun Giderme Sistem Yönetimi Alarm Mesajlarına Cevap Verme Yöntemleri . . . . . . .
Blade Kartına Yönelik Sorun Giderme . . . . . . . . . . . . . . . . . NVRAM Yedek Piline Yönelik Sorun Giderme . . . . . . . . . 6 Sistem Tanılamalarını Çalıştırma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dell PowerEdge Diagnostics (Tanılama) . Sistem Tanılama Özellikleri . . . . . . . . . . . . 342 . . . . . . . . . 342 . . . . . . . . . . 343 Tümleşik Sistem Tanılamasını Çalıştırma . . . . . . . . . . . . . . . . . . . . 343 . . . . . . . . . . . 343 . . . . 345 . . .
PowerEdge M710HD Atlama Teli Ayarları . . . . . . . . . . . . . . . . . . . PowerEdge M610/M610x Atlama Teli Ayarları . . . . . . . . . . . . . . . . . . . 353 . . . 354 . . . . . . . . . . . . 355 PowerEdge M600 Atlama Teli Ayarları Sistem Kartı Konektörleri . PowerEdge M915 Sistem Kartı . . . . . . . . 355 PowerEdge M910 Sistem Kartı . . . . . . . . 357 PowerEdge M905 Sistem Kartı . . . . . . . . 359 PowerEdge M805 Sistem Kartı . . . . . . . . 361 PowerEdge M710 Sistem Kartı . . . .
İçerik
Sisteminiz Hakkında Başlatma Sırasında Sistem Özelliklerine Erişim Tuş vuruşu Açıklama Sistem Kurulumu programına girer. Bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149. Dell Birleşik Sunucu Yapılandırıcıyı (USC) açan Sistem Hizmetlerine girer. Dell USC, tümleşik sistem tanılama gibi yardımcı programlara erişiminizi sağlar. Daha fazla bilgi için, Birleşik Sunucu Yapılandırıcı belgelerine bakın.
Sisteme Genel Bakış Sisteminiz en fazla 16 yarı-yüksek blade (sunucu modülleri), sekiz tam-yüksek blade ya da her iki blade tipinin karışımını içerebilir (bkz. Şekil 1-1, Şekil 1-2 ve Şekil 1-3). Blade, sistem olarak fonksiyon göstermek üzere, güç kaynağı, fan modülleri, Şasi Yönetim Denetleyicisi (CMC) modülü ve harici ağ bağlantısı için en az bir adet G/Ç modülünü destekleyen bir kasa (şasi) içerisine yerleştirilmiştir.
Şekil 1-2.
Şekil 1-3.
Sistem Kontrol Paneli Özellikleri Şekil 1-4.
Tablo 1-1. Kontrol Paneli Özellikleri Öğe Gösterge, Simge Düğme veya Konektör Açıklama Sistem güç düğmesi Yok Sistemi açar ve kapar. Sistemi açmak için basın. Sistemi kapamak için 10 saniye süreyle basılı tutun. NOT: Sistem güç düğmesi kasa içerisindeki tüm blade'lere ve G/Ç modüllerine giden gücü kontrol eder. Sistem güç göstergesi Kapalı Kasada güç yok. Yeşil Sistem gücü açık.
LCD Modülü LCD modülü başlangıç yapılandırma/yerleştirme sihirbazı ve ayrıca altyapı, blade bilgisi ve hata raporlamaya kolay erişim sağlar. Bkz. Şekil 1-5. Şekil 1-5.
LCD Modülü Özellikleri LCD modülünün ana fonksiyonu kasa içerisindeki modüllerin sağlıkları ve durumları hakkında gerçek zamanlı bilgi sağlamaktır. LCD modülü özellikleri şunları içerir: • Başlangıç sistem kurulumu sırasında CMC modülü ağ ayarlarını yapılandırmanıza imkan veren bir yürütme kurulumu sihirbazı. • Her blade'de iDRAC'i yapılandırmaya imkan veren menüler. • Her blade için durum bilgisi ekranları.
Yapılandırma Sihirbazı DHCP için CMC mevcuttur. Statik IP adresi kullanmak için, ister LCD Yapılandırma Sihirbazı'nı kullanarak isterse yönetim istasyonunu ve CLI komutlarını kullanarak CMC ayarını, DHCP'den statik adrese değiştirmeniz gerekir. (Daha fazla bilgi için, bkz. PowerEdge M1000e Yapılandırma Kılavuzu veya CMC belgeleri.) NOT: Yapılandırma sihirbazını çalıştırdıktan sonra, bu seçenek LCD menülerinde artık görüntülenmez. 1 İletişim kutusunda sunulan seçeneklerden bir dil seçin.
Ana Menü Ana Menü seçenekleri, LCD Kurulum Menüsüne, Sunucu Menüsüne ve Kasa Menüsüne bağlantılar içerir. LCD Kurulum Menüsü Bu menüyü kullanarak LCD menü ekranlarına yönelik varsayılan dil ve başlatma ekranı ayarlarını değiştirebilirsiniz. Sunucu Menüsü Sunucu Menüsü iletişim kutusundan ok tuşlarını kullanarak kasada bulunan her blade'i işaretleyebilir ve ardından durumunu görüntüleyebilirsiniz. • Kapalı konumda olan ya da başlatma sürecinde bulunan blade'ler gri renkli dikdörtgen ile ifade olunur.
Blade Özellikleri Şekil 1-6.
Şekil 1-7.
Şekil 1-8.
Şekil 1-9.
Şekil 1-10.
Şekil 1-11.
Şekil 1-12.
Şekil 1-13.
Tablo 1-3. Blade Kontrol Paneli Özellikleri Özellik Simge blade güç göstergesi Açıklama Kapalı – Blade'e gelen güç beslemesi kesilmiştir, blade bekleme modundadır, blade açık konumda değildir ya da blade doğru şekilde kurulmamıştır. Blade kurulumu ile ilgili ayrıntılı bilgi için, bkz. "Bir Blade'in Takılması" sayfa 174. Yeşil renkte düşük parlaklıktan tam parlaklığa artıyor – Blade güç açma talebi beklemededir. Yeşil renk açık – Blade açılmıştır.
USB Disket veya USB DVD/CD Sürücülerini Kullanma Her blade'in ön tarafında USB disket sürücüsü, USB flaş sürücüsü, USB DVD/CD sürücüsü, klavye veya fare bağlamanıza imkan veren bir USB bağlantı noktası bulunur. Blade'i yapılandırmak için USB sürücüleri kullanılabilir. NOT: Bu blade'ler sadece Dell-markalı USB 2.0 sürücüleri destekler. Sürücü yatay olmalı ve doğru şekilde çalışabilmesi için düz bir yüzeyde bulunmalıdır.
• PowerEdge M610, M610x, M600 ve M605 bir veya iki adet 2,5 inç'lik SATA sabit sürücüsünü veya bir veya iki adet 2,5 inç'lik SAS sabit sürücüsünü destekler. NOT: SAS ve SATA sabit sürücüleri blade içerisinde karıştırılamazlar. NOT: SATA sabit sürücüleri, SATA tekrarlayıcı çekme (repeater daughter) kart ile birlikte çalıştırılırken çıkarılıp takılabilme özelliğine sahip değillerdir.
Şekil 1-14. Sabit Sürücü Göstergeleri 2 1 1 sürücü-etkinlik göstergesi (yeşil) Tablo 1-4. 2 sürücü-durum göstergesi (yeşil ve sarı) Sabit Sürücü Göstergeleri Koşul Sürücü Durumu Gösterge Modeli Sürücü tanımlama/sökme işlemi için hazırlık Saniyede iki kere yeşil renkte yanıp söner Takma ya da sökme işlemi Kapalı için sürücü hazır NOT: Sürücü durum göstergesi, sistem gücü açıldıktan sonra tüm sabit sürücüler başlatılana kadar kapalı konumda kalır.
Arka Panel Özellikleri Şekil 1-15.
Şekil 1-16.
Güç Kaynağı Göstergesi NOT: Güç kaynakları doğrudan bir elektrik prizine değil, bir PDU'ya bağlanmalıdır. • Güç kaynakları 200–240 V güç kaynağına ihtiyaç duyarlar. • 2700 W güç kaynağı 110 V AC güç kaynağına bağlanabilir. Şekil 1-17.
Tablo 1-5. Güç Kaynağı Göstergeleri Gösterge Simge Açıklama Güç kaynağı durumu Yeşil renk, güç kaynağının çalıştığını ve sisteme DC gücü sağladığını gösterir. Arıza göstergesi Sarı renk, arızalanan bir güç kaynağı ya da güç kaynağı içerisinde bir fanın arızalanması sonucu oluşabilecek güç kaynağı ile ilgili bir sorun olduğunu ifade eder. Bkz. "Güç Kaynağı Modülleri.
Tablo 1-6. Fan Göstergeleri Gösterge Gösterge Açıklama Durumu Güç göstergesi Yeşil Güç kaynağı AC güç kaynağına bağlanmıştır. Kapalı AC güç beslemesi bağlı değildir. Arıza göstergesi Sarı Kapalı Fan arıza durumundadır. Fan arızalı değildir. Merkez Hattı Versiyonunun Belirlenmesi Kasaya takılan merkez hattının versiyonu CMC web tabanlı arayüzünün Özet sekmesindeki Merkez Hattı Revizyonu alanında görüntülenir.
Şekil 1-19. Merkez Hattı Versiyon 1.
Şekil 1-20. Merkez Hattı Versiyon 1.
iKVM Modülü İsteğe bağlı, Avocent iKVM analog anahtar modülü aşağıdaki özellikleri içerir: • Yerel iKVM erişimi, blade'in sahip olduğu iDRAC arabirimini kullanılarak, her blade için ayrı ayrı olmak üzere uzaktan devre dışı bırakılabilir (varsayılan olarak erişim etkinleştirilmiştir).
• RACADM kullanarak veya web tabanlı arabirim aracılığıyla CMC denetim paneline doğrudan erişmek için iKVM'yi kullanabilirsiniz. Daha detaylı bilgi için, CMC Kullanım Kılavuzu'nda bulunan "iKVM Modülünü Kullanma" başlığına başvurun. Şekil 1-21 iKVM anahtar modülünün harici özelliklerini görüntüler. Şekil 1-21.
Tablo 1-8. Özellik Avocent Analog iKVM Anahtar Modülü Özellikleri Gösterge Deseni Açıklama Güç göstergesi Kapalı Durum/ tanımlama göstergesi iKVM anahtarında güç yok. Yeşil iKVM anahtarında güç var. Yeşil renkte yanıp sönüyor Bellenim yükseltmesi gerçekleştiriliyor Yanıp sönen mavi iKVM modülü tanımlanıyor. Sarı yanıp sönüyor Sistem arızası veya hata durumu. USB konektörleri Bir klavye ya da farenin sisteme bağlanmasına izin verir.
Avocent iKVM Anahtarını Analog KVM Anahtarından Sıralama Avocent iKVM anahtarı, Dell 2160AS ve 180AS gibi analog KVM anahtarlarından sıralanabildiği gibi pek çok Avocent analog KVM anahtarından da sıralanabilir. Pek çok anahtar Sunucu Arabirimi Poduna (SIP) ihtiyaç duyulmadan sıralanabilir (bkz. Tablo 1-9). Tablo 1-9.
Ekran Gecikme Süresini 1 saniye olarak ayarlamak, OSCAR'ı başlatmadan bir sunucuya yumuşak geçiş yapmanızı sağlar. NOT: Yumuşak geçiş, sunucuları kısayol tuş dizisi kullanarak değiştirmenize imkan verir. Bir sunucuya (Ekranı Yazdır) öğesine basıp ardından adının ilk harflerini ya da rakamlarını girerek yumuşak geçiş yapabilirsiniz. Gecikme Süresi belirlediyseniz ve bu süre geçmeden tuş dizisine basarsanız, OSCAR görüntülenmez.
4 Harici analog anahtarını açın. NOT: Harici analog anahtarı sistemden önce açılırsa, bu durum OSCAR analog anahtarında 16 yerine sadece bir blade'in görüntülenmesine sebep olabilir. Böyle bir durumla karşılaşılması durumunda blade'in tüm bileşenlerinin tanımlanması amacıyla anahtarı kapayıp tekrar başlatın.
• Anahtar, USB SIP (bkz. Tablo 1-9) gereksinimi duyuyorsa, iKVM'ye bir USB SIP bağlayın ve ardından SIP'ye bir Cat5 (ya da daha yeni) bir kablo bağlayın. Bu kablonun diğer ucunu harici anahtar üzerinde bulunan ARI bağlantı noktasına bağlayın. KVM anahtarı bağlandıktan sonra, sunucu modülü OSCAR'da görüntülenir. NOT: Yerel sistem kurulduktan sonra, blade listesini görebilmek için Uzak Konsol Anahtarı yazılımından sunucu listesini de yeniden senkronize etmeniz gerekir. Bkz.
3 Next (İleri) öğesini tıklatın. Anahtar bilgisinin alındığını ifade eden bir ilerleme çubuğu ile birlikte bir Sorgulama Uzak Konsol Anahtarı mesaj kutusu görüntülenir. 4 Uygulamada herhangi bir değişiklik saptanmazsa, bu bilgi ile birlikte bir tamamlama iletişim kutusu görüntülenir. Sunucu değişikliklerinin saptanması durumunda, Saptanan Değişiklikler iletişim kutusu görüntülenir. Veri tabanını güncellemek için Sonraki öğesine tıklayın.
CMC Modülü Şekil 1-22.
Tablo 1-11. CMC Modülü Özellikleri Gösterge Model Açıklama Ağ arabirimi denetleyicisi bağlantı göstergesi Kapalı LAN bağlantısı kurulmadı. Yeşil LAN bağlantısı kuruldu. Ağ arabirimi denetleyicisi etkinlik göstergesi Kapalı LAN etkin değil. Sarı renkte yanıp sönüyor CMC sisteminin ve LAN'ın iletişim halinde olduğunu ifade eder. Güç göstergesi Kapalı CMC'de güç yok. Yeşil CMC'de güç var. Yeşil renkte Bellenim güncellemesi yürütülüyor.
CMC, modüler sunucunuza yönelik çoklu sistem yönetimi fonksiyonu sunar: • • 54 Kasa-seviyesinde gerçek-zamanlı otomatik güç ve termal yönetimi. – CMC, sistem güç gereksinimlerini izler ve etkin güç tüketimini artırmak amacıyla mevcut yüke ve yedekleme durumuna bağlı olarak bekleme konumunda güç kaynaklarını dinamik olarak etkinleştirebilmek ya da yerleştirebilmek için isteğe bağlı Dinamik Güç Besleme Kavrama modunu destekler.
CMC, iki Ethernet bağlantı noktasına sahiptir: Gb1, harici yönetim ağına bağlanmak için kullanılır. STK ("yığın") etiketli konektör, komşu kasalarda bulunan CMC'lerin zincirleme-bağlanmasına imkan verir. 24-bağlantı noktalı Ethernet anahtarı her blade üzerinde bulunan iDRAC ile, G/Ç modülleri, isteğe bağlı KVM ve isteğe bağlı ikinci, yedek CMC arasında dahili iletişim kurulmasını sağlar.
Şekil 1-23.
G/Ç Bağlantısı M1000e kasası, Ethernet, fiber-kanal ve Infiniband modül kombinasyonları arasından seçilebilen üç katmanlı G/Ç yapısını destekler. Kasaya fiber-kanal anahtarlar, fiber kanal geçişleri, Infiniband anahtarları, Ethernet anahtarları ve Ethernet geçiş modülleri dahil olmak üzere altı adede kadar çalışırken çıkarılıp takılabilme özelliğine sahip G/Ç modülü takabilirsiniz. G/Ç Modüllerinin Takılmasına Yönelik Kılavuzlar G/Ç modülleri oluştururken bu kılavuzları takip etmeniz gerekir.
Yapı A Yapı A, yedek Gb Ethernet yapısıdır ve I/O modülü A1 ve A2 yuvalarını destekler. Her blade'de bulunan tümleşik Ethernet denetleyicileri Yapı A'yı sadece-Ethernet için kullanılabilir bir yapı olarak dikte eder. NOT: Kasadaki merkez hattı versiyonu 1.1 veya daha sonraki bir sürüm ise Yapı A KR'yi (10 Gbps standart) destekler. Merkez hattı versiyonunu belirlemek için, bkz. "Merkez Hattı Versiyonunun Belirlenmesi" sayfa 41.
Yapı C yuvalarında bulunan bir G/Ç modülü ile iletişim kurmak için, blade'de Yapı C ara kat kartı konumunda denk gelen bir ara kat kartının takılı olması gereklidir. Yapı A için tasarlanan modüller ayrıca Yapı C yuvalarına da takılabilir. Dört Bağlantı Noktalı Ağ Ek Kartında Otomatik Bağlantı Noktası Devre Dışı Bırakma (Sadece PowerEdge M710HD) Dört bağlantı noktalı Ağ Ek Kartı destekli Otomatik Bağlantı Noktası Devre Dışı Bırakma ile kurulan sistemler.
Tablo 1-12.
Tam Yüksekliğe sahip Blade'ler Tam yüksekliğe sahip blade'ler dört adet ara kat kartı desteklerler: • Mezz1_Fabric_C yuvası ve Mezz3_Fabric_C yuvası Yapı C'yi destekler. Ayrıca G/Ç modülü C1 ve C2 yuvalarına takılan G/Ç modülü yapı tipi ile eşleşmeleri gerekmektedir. • Mezz2_Fabric_B yuvası ve Mezz4_Fabric_B yuvası Yapı B'yi destekler. Ayrıca G/Ç modülü B1 ve B2 yuvalarına takılan G/Ç modülü yapı tipi ile eşleşmeleri gerekmektedir.
Tablo 1-13.
Tablo 1-13.
Tam Yüksekliğe sahip Blade'ler Standart LOM (Dual-Port) Eşleştirme Her birinin iki bağlantı noktası bağlantısı vardır. n yuvasında bulunan tam yüksek blade için: • Tümleşik NIC LOM1, bağlantı 1, G/Ç modülü A1, bağlantı noktası n'ye bağlanır. Tümleşik NIC LOM1, bağlantı 2, G/Ç modülü A2, bağlantı noktası n'ye bağlanır. • Tümleşik NIC LOM2, bağlantı 1, G/Ç modülü A1, bağlantı noktası n'ye bağlanır. Tümleşik NIC LOM2, bağlantı 2, G/Ç modülü A2, bağlantı noktası n'ye bağlanır.
Örneğin, tam yüksekliğe sahip bir ara kat kartı 3'te, bağlantı 1 G/Ç modülü C1 bağlantı noktası 13'e ve Ara Kat kardı 3'e, bağlantı 2 G/Ç modülü C2 bağlantı noktası 13'e bağlanacaktır. Tablo 1-15 sekiz olası tam yüksek blade konumu için bağlantı noktası numarası atamalarını gösterir. NOT: PowerEdge M610x bir tam blade sistemi olmasına rağmen, genişletme yuvasında sadece iki ara kat kartı yuvası (MEZZ1_Fab_C1 ve MEZZ2_FAB_B1) kullanıma uygundur.
Şekil 1-24.
Tablo 1-15.
Blade 3 G/Ç Modülü B1 Mezz1_Fab_C Mezz2_Fab_B Bağlantı noktası 3 B2 Bağlantı noktası 3 Bağlantı Bağlantı noktası noktası 11 11 Bağlantı noktası 11 Blade 4 Bağlantı noktası 11 G/Ç Modülü B1 Mezz1_Fab_C Mezz2_Fab_B Mezz4_Fab_B C1 C2 B2 Bağlantı Bağlantı noktası 4 noktası 4 Bağlantı noktası 4 Mezz3_Fab_C 68 C2 Bağlantı Bağlantı noktası 3 noktası 3 Mezz3_Fab_C Mezz4_Fab_B C1 Bağlantı noktası 4 Bağlantı Bağlantı noktası noktası 12 12 Bağlantı noktası 12 Sisteminiz Hakkında Bağlantı nokt
Blade 5 G/Ç Modülü B1 Mezz1_Fab_C Mezz2_Fab_B Bağlantı noktası 5 Bağlantı noktası 5 Bağlantı noktası 13 Bağlantı noktası 13 G/Ç Modülü B1 Mezz1_Fab_C C1 C2 B2 Bağlantı Bağlantı noktası 6 noktası 6 Bağlantı noktası 6 Mezz3_Fab_C Mezz4_Fab_B B2 Bağlantı Bağlantı noktası noktası 13 13 Blade 6 Mezz2_Fab_B C2 Bağlantı Bağlantı noktası 5 noktası 5 Mezz3_Fab_C Mezz4_Fab_B C1 Bağlantı noktası 6 Bağlantı Bağlantı noktası noktası 14 14 Bağlantı noktası 14 Bağlantı noktası 14 Sisteminiz Hakk
Blade 7 G/Ç Modülü B1 Mezz1_Fab_C Mezz2_Fab_B Bağlantı noktası 7 Bağlantı noktası 7 Bağlantı noktası 15 B1 Mezz1_Fab_C Bağlantı noktası 15 G/Ç Modülü V C1 B2 C2 Bağlantı Bağlantı noktası 8 noktası 8 Bağlantı noktası 8 Mezz3_Fab_C Mezz4_Fab_B B2 Bağlantı Bağlantı noktası noktası 15 15 Blade 8 Mezz2_Fab_B C2 Bağlantı Bağlantı noktası 7 noktası 7 Mezz3_Fab_C Mezz4_Fab_B C1 Bağlantı noktası 8 Bağlantı Bağlantı noktası noktası 16 16 Bağlantı noktası 16 Bağlantı noktası 16 Şekil 1-25, d
Şekil 1-25. Tam Yüksek Blade Bağlantı Noktası Eşleştirme Örneği Blade 3 (PowerEdge M610x için uygun değildir) Dört Bağlantı Noktalı Ara Kat Kartları Tablo 1-16, dört bağlantı noktalı ara kat kartlı tam yüksek blade'lere ilişkin G/Ç modülü bağlantı noktası adreslemeyi gösterir. NOT: Her bir PowerEdge sisteminin ayrıntılı adreslemesi için, support.dell.com/manuals adresindeki M1000e Modüler Kasa için Dört Bağlantı Noktası Kapasiteli Donanım belgesine bakın.
Tablo 1-16. G/Ç Modülü Bağlantı Noktası Atamaları—Tam Yüksek Blade'ler (PowerEdge M610x için geçerli değildir) Blade n ve Blade (n + 8) NOT: n 1 ile 8 arasında değişen bit değeri belirtir.
Tablo 1-16. G/Ç Modülü Bağlantı Noktası Atamaları—Tam Yüksek Blade'ler (PowerEdge M610x için geçerli değildir) (devamı) Blade n ve Blade (n + 8) NOT: n 1 ile 8 arasında G/Ç Modülü B1 C1 C2 B2 değişen bit değeri belirtir.
Tablo 1-17, PowerEdge M610x için yuva n'deki G/Ç modülü bağlantı noktası eşleştirmesini göstermektedir. Tablo 1-17.
Ağ Ek Kartlı ((PowerEdge M710HD) yarım yüksek blade'ler her biri iki bağlantı noktası bağlantısına sahip iki ağ denetleyicisini (LOM1 ve LOM2) barındırır. n yuvasında bulunan yarı yüksek blade için: • Tümleşik NIC LOM1, bağlantı 1 G/Ç modülü A1 bağlantı noktası n'ye bağlanır. Tümleşik NIC LOM1, bağlantı 2 G/Ç modülü A2 bağlantı noktası n'ye bağlanır. • Tümleşik NIC LOM2, bağlantı 1 G/Ç modülü A1 bağlantı noktası n+16'ya bağlanır.
Tablo 1-18. G/Ç Modülü Bağlantı Noktası Atamaları Örneği Yarı Yüksek Blade 1 G/Ç Modülü Blade 1 A1 Tümleşik NIC B1 C2 B2 Bağlantı noktası 1 A2 Bağlantı noktası 1 Ara Kat Kartı C Ara Kat Kartı B C1 Bağlantı Bağlantı noktası 1 noktası 1 Bağlantı noktası 1 Bağlantı noktası 1 Şekil 1-26, iki ara kartlı yuva 1'de bulunan yarı yüksek blade'ler için bağlantı noktası bağlantılarını gösterir.
Şekil 1-26.
Dört Bağlantı Noktalı Ara Kat Kartları Tablo 1-19 , dört bağlantı noktalı ara kat kartlı yarı yüksek blade'lere ilişkin G/Ç modülü bağlantı noktası adreslemeyi gösterir. Aşağıdaki, tabloda n, 1 ile 16 arasında değişen bir değeri belirtmektedir. NOT: Her bir PowerEdge sisteminin ayrıntılı adreslemesi için, support.dell.com/manuals adresindeki M1000e Modüler Kasa için Dört Bağlantı Noktası Kapasiteli Donanım belgesine bakın. Tablo 1-19.
Tablo 1-19. G/Ç Modülü Bağlantı Noktası Atamaları—Yarı Yüksek Blade'ler Blade n G/Ç Modülü A1 B1 C1 Mezz_FAB_C_Blade n_Port2 Mezz_FAB_C_Blade n_Port3 C2 B2 A2 Bağlant ı noktası n Bağlantı Noktası (n+16) Mezz_FAB_C_Blade n_Port4 Bağlant ı Noktası (n+16) Dell PowerConnect-KR 8024-k Anahtar PowerConnect M8024-k anahtar, 16 adet dahili 10 GbE bağlantı noktası, dört adet harici 10 GbE SFP+ bağlantı noktası ve 10 GbE harici çıkış bağlantısı için bir adet 10 GbE genişletme yuvası sağlar.
Şekil 1-27.
Dell M8428-k 10 Gb Yakınsak Ağ Anahtarı Dell M8428-k 10 Gb Yakınsak Ağ anahtarı FCoE protokollerini destekler ve Fiber Kanal trafiğinin 10 Gbps Yakınsak Gelişmiş Ethernet (DCB) ağları üzerinden iletilmesine imkan sağlar.
Şekil 1-28.
Mellanox M3601Q QDR Infiniband Anahtar G/Ç Modülü Mellanox M3601 Infiniband anahtar G/Ç modülü, 32 4x QDR Infiniband bağlantı noktalarını içerir. Bu bağlantı noktalarından 16'sı harici çıkış bağlantı noktasıdır, 16 dahili bağlantı noktası ise kasa içerisindeki blade'lere bağlantı sağlar. Modül, iki G/Ç modülü yuvasında bulunur. M3610Q modülü G/Ç modülü yuva C1'e takılır ancak hem yuva B1 hem de C1'i kullanır.
Şekil 1-29.
Mellanox M2401G Infiniband Anahtar G/Ç Modülü Mellanox M2401G Infiniband Anahtar G/Ç modülü, 24 4x DDR Infiniband bağlantı noktalarını içerir. Sekiz bağlantı noktası harici çıkış bağlantı noktasıdır, 16 dahili bağlantı noktası ise kasa içerisindeki blade'lere bağlantı sağlar. Şekil 1-30.
Tablo 1-20. Mellanox M2401G Infiniband Anahtar Göstergeleri Gösterge Model Açıklama Bağlantı göstergesi Yeşil, açık Fiziksel bağlantı kuruldu Yeşil, kapalı Fiziksel bağlantı yok Faaliyet gösteresi Sarı, açık Infiniband ağına geçerli mantıksal bağlantı kuruldu Sarı, yanıp sönüyor Veri transferi devam ediyor Sarı, kapalı Infiniband ağına mantıksal bağlantı yok Cisco SFS M7000e Infiniband Anahtar Modülü Cisco SFS M7000e Infiniband anahtar modülü, 24 4x DDR Infiniband bağlantı noktalarını içerir.
Şekil 1-31.
Tablo 1-21.
Şekil 1-32.
PowerConnect M6348 1 Gb Ethernet Anahtarı G/Ç Modülü PowerConnect M6348, sistem çalışırken sökülüp takılabilen 48 bağlantı noktalı 1 Gb'lık bir Ethernet anahtarıdır. 16 bağlantı noktası harici çıkış bağlantı noktası iken kalan 32 adet dahili bağlantı noktası kasa içerisindeki blade'lere her biri maksimum 1 Gbps bant genişliği ile bağlantı sağlar.
Şekil 1-33.
PowerConnect M8024 10 Gb Ethernet Anahtarı G/Ç Modülü PowerConnect M8024 anahtar modülü, aşağıdaki modülleri destekleyen iki isteğe bağlı yuvayla birlikte çalışır: • Dört optik SFP+ konektörlü 10 Gb'lık bir Ethernet modülü • Üç bakır CX4 çıkış bağlantılı 10 Gb'lık bir Ethernet modülü İki yöntemden birini kullanarak anahtara ilk yapılandırmayı yapabilirsiniz: • Bir USB A tipi form faktörü seri kablosu kullanarak anahtara bir harici yönetim sistemi bağlayın ve anahtarı uzak uç uygulaması kullanarak yapıl
Şekil 1-34.
PowerConnect M6220 Ethernet Anahtar Modülü PowerConnect M6220 Ethernet anahtar modülü, dört adet harici 10/100/1000 Mbps Ethernet konektörü ve bir adet UAB A tipi form faktörü seri bağlantı konektörünü içerir. Bkz. Şekil 1-35.
Şekil 1-35.
Dell 10 GbE KR Geçiş G/Ç Modülü 10 GbE KR geçiş modülü 10 Gb bağlantıları destekler ve blade'deki isteğe bağlı dahili Ethernet KR ara kat kartı veya KR ağ kartı ve harici Ethernet aygıtı arasında doğrudan bağlantı sağlar. Bu modül ön panel üzerinde 16 adet harici SFP+ bağlantı noktasına ve arka panelde on altı adet 10 GbE KR dahili bağlantı noktasına sahiptir. Bu modül optik SFP+ (kısa erişim veya uzun erişim) ve doğrudan bağlı bakır (DCA) SFP+ modüllerini kullanmanıza imkan sağlar.
Şekil 1-36.
Dell 8/4 Gbps Fiber Kanal Geçiş G/Ç Modülü 8G Fiber Kanal geçiş modülü blade'deki bir Fiber Kanal ara kat kartı ve optik alıcı vericiler arasında bir baypas bağlantısı sağlar. Baypas bağlantısı bir Fiber Kanal anahtarı veya bir depolama dizisine doğrudan bir bağlantı sağlar. Modül üzerindeki 16 geçiş bağlantı noktası, 2, 4 ve 8 Gbps hızlarla uyumludur. 8G Fiber Kanal geçiş modülü sistem çalışırken sökülüp takılabilir ve Yapı B veya Yapı C'ye takılabilir.
Şekil 1-37.
10 Gb Ethernet Geçiş Modülü II Dell 10 Gb Ethernet geçiş modülü II 10 Gb bağlantılarını destekler ve blade'deki isteğe bağlı dahili Ethernet ara kat kartı ve harici bir Ethernet aygıtı arasında doğrudan bir bağlantı sağlar. Ethernet geçiş modülleri sistem çalışırken sökülüp takılabilir ve Yapı B veya Yapı C'ye takılabilir. 10 Gb Ethernet geçiş modülü II optik SFP+ ve doğrudan ekli bakır (DCA) SFP+ modüllerini kullanmanıza olanak tanır.
Şekil 1-38.
10 Gb Ethernet Geçiş G/Ç Modülü 10 Gb Ethernet geçiş modülü 1/10 Gb bağlantılarını destekler ve blade'deki isteğe bağlı dahili Ethernet ara kat kartı ve harici bir Ethernet aygıtı arasında doğrudan bir bağlantı sağlar. Ethernet geçiş modülleri sistem çalışırken sökülüp takılabilir ve Yapı B veya Yapı C'ye takılabilir. 10 Gb Ethernet geçiş G/Ç modülü optik SFP, SFP+ ve doğrudan ekli bakır (DCA) SFP+ modüllerini kullanmanıza olanak tanır.
Şekil 1-39.
4 Gbps Fiber Kanal Geçiş Modülü 4 Gbps Fiber Kanal geçiş modülü, Fiber Kanal anahtarına ya da bir depolama dizisine doğrudan bağlantı için blade içerisindeki bir fiber Kanal ara kat kartı ile optik alıcı-vericiler arasında bypass bir bağlantı sağlar (bkz. Şekil 1-40). Modül üzerindeki 16 geçiş bağlantı noktası, 1-, 2- ve 4-Gbps hızlarla uyumludur. 4 Gbps Fiber Kanal geçiş modülleri sistem çalışırken sökülüp takılabilir ve Yapı B veya Yapı C'ye takılabilir.
Şekil 1-40.
Tablo 1-22.
Tablo 1-22.
Şekil 1-41.
Tablo 1-23.
Brocade M4424 SAN G/Ç Modülü Brocade M4424 G/Ç modülü, sekiz adet otomatik algılayıcı harici Fiber Kanal bağlantı noktası (dört bağlantı noktası standart yapılandırmada etkindir ve isteğe bağlı bir yükseltme olarak dört ek bağlantı noktası etkinleştirilebilir), 16 dahili bağlantı noktası ve RJ-45 konektörlü bir seri bağlantı noktası içerir. Harici Fiber Kanal bağlantı noktaları 1 Gb/san, 2 Gb/san veya 4 Gb/san hızında çalışır.
Şekil 1-42.
Tablo 1-24.
10/100/1000 Mb Ethernet Geçiş Modülü Ethernet geçiş modülü, 10/100/1000 Mb bağlantıları destekler ve blade içerisindeki isteğe bağlı dahili Ethernet ara kat kartı ile harici bir Ethernet aygıtı arasında doğrudan bir bağlantı sağlar (bkz. Şekil 1-43). Ethernet geçiş modülleri sistem çalışırken sökülüp takılabilir ve üç Yapıdan herhangi birine takılabilir. Tablo 1-25, Ethernet geçiş modülü göstergelerinin işlevini listeler. Bu modülün takılmasıyla ilgili ek bilgiler için bkz. "G/Ç Modülleri" sayfa 310.
1 bağlantı göstergesi (16) 2 RJ45 Ethernet konektörü (16) 3 durum/tanımlama göstergesi 4 güç göstergesi 5 faaliyet göstergesi (16) NOT: Ethernet geçiş modülündeki konektörler, doğrudan blade numarasıyla uyumludur. Örneğin blade 5, Ethernet geçiş modülündeki bağlantı noktası 5'e bağlıdır. Tümleşik ağ adaptörü 1, G/Ç yuva A1 ile eşleşir. Tümleşik ağ adaptörü 2, G/Ç yuva A2 ile eşleşir. Tablo 1-25.
LCD Durum Mesajları Aşağıdaki LCD mesajları, Sistem Olay Kaydında (SEL) kayıtlı bulunan olaylarla ilgilidir. (mesajlar burada "basit" metin biçiminde gösterilir.) SEL ve yapılandırma sistemi yönetim ayarları hakkında bilgi için sistem yönetimi yazılım belgelerine bakın. NOT: Sisteminiz önyükleme yapamıyorsa, sistem ID düğmesine, LCD üzerinde bir hata kodu görünene kadar en az beş saniye basın. Kodu kaydedin, ardından bkz. "Yardım Alma" sayfa 377.
Tablo 1-26. LCD Durum Mesajları Kod Metin Neden Çözüm İşlemleri E1000 Failsafe voltage error. Contact support. Önemli hata olayları için sistem olay günlüğünü denetleyin. Sisteme giden AC gücünü 10 saniyeliğine kesin ve SEL'yi temizleyin. E1114 Ambient Temp exceeds allowed range. Ortam sıcaklığı izin verilen Bkz. "Fan Modüllerine aralığın dışındaki bir Yönelik Sorun Giderme" noktaya ulaşmıştır. sayfa 330. E1116 Memory disabled, temp above range. Power cycle AC.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri E1211 RAID Controller battery failure. Check battery. RAID pili eksik, hatalı ya da termal nedenlerden dolayı yeniden şarj edilemeyecek durumdadır. RAID pili konektörünü yeniden yerleştirin. Bkz. "Depolama Denetleyici Kartını Takma" sayfa 296 ve "Fan Modüllerine Yönelik Sorun Giderme" sayfa 330. E1229 CPU # VCORE Regulator failure. Reseat CPU. Belirlenen işlemci VCORE voltaj regülatörü başarısız olmuştur.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri E122E On-board regulator failed. Call support. Yerleşik voltaj düzenleyicilerinden biri başarısız. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. E1310 Fan ## RPM exceeding range. Check fan. Belirtilen pervanenin hızı Bkz. "Fan Modüllerine tasarlanan çalışma aralığının Yönelik Sorun Giderme" dışındadır. sayfa 330. E1311 Fan module ## RPM exceeding range. Check fan.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri Belirlenen işlemci eksik ya da hatalıdır ve sistemin desteklenmeyen bir yapılandırması vardır. Belirtilen işlemcinin düzgün şekilde yerleştirildiğinden emin olun. Bkz. "Sorun Giderme - İşlemciler" sayfa 338. E141C Unsupported İşlemciler desteklenmeyen CPU bir yapılandırmaya sahiptir. configuration Check CPU or BIOS revision.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden E1614 Power Supply Belirtilen güç kaynağı # (### W) başarısız. error. Check power supply. Çözüm İşlemleri Bkz. "Güç Kaynağı Modüllerine Yönelik Sorun Giderme" sayfa 329. E1618 Predictive failure on Power Supply # (### W). Check PSU. Belirlenen güç kaynağı, aşırı Bkz. "Güç Kaynağı sıcaklık uyarısı veya PSU Modüllerine Yönelik iletişim hatası gibi güç Sorun Giderme" sayfa 329.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri E1626 Power Supply Sistemdeki güç kaynakları, Mismatch. aynı watt değerinde PSU1 = ### W, değillerdir. PSU2 = ### W. Watt değerleri eşleşen güç kaynaklarının takıldığından emin olun. Sisteminiz ile Sistem Başlangıç Kılavuzu'nda belirtilen Teknik Özellikler'e bakınız. E1629 Power required > PSU wattage. Check PSU and config. Sistem yapılandırması, güç kaynaklarının sağladığından daha fazla güce gereksinim duyuyor.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri E2010 Memory not detected. Inspect DIMMs. Sistemde bellek algılanamadı. Belleği takın veya bellek modüllerini tekrar yerleştirin. Bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334. E2011 Memory configuration failure. Check DIMMs. Bellek algılandı, ancak yapılandırılabilir değil. Bellek yapılandırması sırasında hata algılandı. Bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin E2016 Interrupt Controller failure. Power cycle AC. Neden Çözüm İşlemleri Kesme denetleyicisi hatası. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. Sorun devam ediyorsa, bkz. "Yardım Alma" sayfa 377. E2017 Timer refresh Zamanlayıcı yenileme failure. hatası. Power cycle AC. E2018 Programmable Timer error. Power cycle AC. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. Sorun devam ediyorsa, bkz.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin E201B Keyboard Controller error. Power cycle AC. Neden Çözüm İşlemleri Klavye denetleyicisi hatası. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. Sorun devam ediyorsa, bkz. "Yardım Alma" sayfa 377. E201C SMI Sistem yönetim kesintisi initializatio (SMI) başlatma hatası. n failure. Power cycle AC. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. E201D Shutdown test BIOS kapatma sınaması failure.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri E2021 Incorrect Incorrect memory memory configuration. configuration. Review User Guide. E2022 General failure during POST. Check screen message. Belirli hata mesajları için ekranı kontrol edin (bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334). Video sonrası genel hata. E2110 Multibit "##" yuvasındaki bellek Error on DIMM modülünün çoklu bit hatası ##. Reseat (MBE) vardır. DIMM.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Neden Çözüm İşlemleri E2113 Mem mirror OFF on DIMM ## & ##. Power cycle AC. Belleğin yarısında çok fazla hata olduğu belirlendiği için, sistem BIOS bellek aynalamasını devre dışı bırakmıştır. "## & ##"; BIOS tarafından belirtilen DIMM çiftini temsil eder. Sisteme giden AC gücünü 10 saniyeliğine kesin ve sistemi yeniden başlatın. I1911 LCD Log Full. Check SEL to review all Errors. LCD taşma mesajı.
Tablo 1-26. LCD Durum Mesajları (devamı) Kod Metin Neden Çözüm İşlemleri W1627 Power required > PSU wattage. Check PSU and config. Sistem yapılandırmasının, güç kaynağının sağladığı güçten daha fazla güce ihtiyacı vardır. Sistemi kapatın, donanım yapılandırmasını azaltın ya da yüksek watt değerli güç kaynaklarını takıp sistemi yeniden başlatın. W1628 Performance degraded. Check PSU and system configuration.
Tablo 1-27. Blade Mesajları Mesaj Nedenleri Çözüm İşlemleri Failed to allocate sufficient blade power. Check PCIe card power usage is within limits. Bu hata, BIOS, belli bir zaman aşımı süresi içinde POST sırasında iDRAC'tan blade için 'Güç Verildi' durumunu almadığı zaman oluşur. Bu hata oluştuğunda POST durdurulur. Bu hataya neden olan yaygın bir durum, iDRAC GUI'de belirtilen PCLe kart gücü tahsisinin çok yüksek olması ve sistem sınırlarını aşmasıdır. NOT: Sadece M610x için mevcuttur.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Error: Unsupported Bu hata takılan ara kat mezzanine card kartlarının türü ve configuration. yapılandırması desteklenmediğinde oluşur. Takılan ara kat kartlarının blade tarafından desteklendiğinden emin olun. Bkz. "G/Ç Modül Ara Kat Kartları" sayfa 232. Verifying blade power... POST'ta ilerlemeden önce Yalnızca bilgi vermek içindir. BIOS'un iDRAC/CMC'nin blade'e güç vermek için beklediği durum mesajı. Cannot Power ON.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Global PFault detected in Expansion Genişletmede bir PFault oluşmuştur. Bkz. "Yardım Alma" sayfa 377. NOT: Sadece M610x için mevcuttur. PCIe card inserted Yeni bir PCIe kartı takıldı. in slot X [Vendor ID: YYYY Device ID: ZZZZ] Sadece bilgi amaçlı. PCIe card removed from slot X Bir PCIe genişletme kartı çıkarılmış. Genişletme kartını yeniden takın. Bkz. "Genişletme Kartını Takma" sayfa 251.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri DIMM configuration Çift işlemcili sistemde on each CPU should geçersiz bellek match yapılandırması. Her işlemci için aynı DIMM yapılandırması yapılmalıdır. Bellek modüllerinin geçerli bir yapılandırmada takıldığından emin olun. Bkz. "Sistem Belleği" sayfa 186. Maximum rank count exceeded. The following DIMM has been disabled: Geçersiz bellek yapılandırması. Sistem belirtilen DIMM devre dışı bırakılmış halde çalışır.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri The following DIMM's should match in size: Geçersiz bellek yapılandırması. Belirtilmiş DIMM'ler boyut, aşama sayısı ya da veri hatları sayısı ile eşleşmez. Bellek modüllerinin geçerli bir yapılandırmada takıldığından emin olun. Bkz. "Sistem Belleği" sayfa 186. in rank count: in size and rank count: in geometry: in size and geometry: Thermal sensor not Geçersiz bellek Bellek modüllerinin geçerli detected on yapılandırması.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri CPU x installed with no memory Belirtilen işlemcinin bellek İşlemci için bellek yuvalarına bellek modülleri modüllerini kurun. gereklidir ancak kurulmadı. Bkz. "Sistem Belleği" sayfa 186. Unused memory detected. DIMM's installed in the following slot are not available when in Mirror or 128Bit Advanced ECC modes: x,x,x Bellek yapılandırması aynalama veya Gelişmiş ECC Bellek Modu için ideal değildir.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Alert! Redundant Kurulan bellek memory disabled! yapılandırması, yedek Memory belleği desteklemiyordur. configuration does not support redundant memory. Alert! Redundancy was previously lost. Power cycle required to reconfigure redundant memory. Bellek hatası. Çözüm İşlemleri Yedek belleği destekleyen bir bellek yapılandırması kurun. Bkz. "Sistem Belleği" sayfa 186. Sistem Kurulumu programından Yedek Bellek seçeneğini devre dışı bırakın. Bkz.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Decreasing available memory. Arızalı veya düzgün takılmamış bellek modülleri. Tüm bellek modüllerinin düzgün takıldığından emin olun. Bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334. DIMMs disabled - SMI channel training failure. Bellek modülleri düzgün bir şekilde takılmamıştır. Bellek Modüllerini yeniden takın veya değiştirin. Bkz. "Sistem Belleği" sayfa 186.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri DIMMs Bellek modülleri düzgün disabled - MemBIST bir şekilde takılmamıştır. error. Bellek modülü konektörü toza maruz kalmış olabilir. DIMMs disabled - MemBIST Desteklenmeyen bellek timeout. modülü. DIMMs disabled - Rank not found. DIMMs disabled - DIMM communication error. DIMMs disabled - DDR training error. Çözüm İşlemleri Bellek modülünü(modüllerini) değiştirin veya yeniden takın. Bkz.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri DIMMs should be installed in pairs. Pairs must be matched in size, speed, and technology. Eşleşmeyen veya yanlış eşleşen DIMM'ler takılı; arızalı veya yanlış takılmış bellek modülleri. Sistem, azalan ECC korumasıyla bozuk bir modda çalışır. Yalnızca kanal 0'a takılan bellek erişilirdir. Tüm bellek modülü çiftlerinin aynı tipte, aynı boyutta olduğunu ve doğru takıldıklarını kontrol edin. Bkz. "Sistem Belleği" sayfa 186.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Error: Incorrect memory configuration. DIMMs must be installed in pairs of matched memory size, speed, and technology. Eşleşmeyen veya yanlış eşleşen DIMM'ler takılı; arızalı veya yanlış yerleştirilmiş bellek modülleri. Tüm bellek modülü çiftlerinin aynı tipte, aynı boyutta olduğunu ve doğru takıldıklarını kontrol edin. Bkz. "Sistem Belleği" sayfa 186. Sorun devam ederse, bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri FBD training Belirlenen dizin (kanal error: The çifti), birbirleriyle uyumsuz following branch DIMM'ler içeriyordur. has been disabled: Branch x. Yalnızca Dell onaylı bellek kullanıldığından emin olun. Uyumluluğun garanti altına alınması için Dell, bellek yükseltme kitlerini doğrudan http://www.dell.com adresinden veya Dell satış temsilcisinden almanızı önerir. Gate A20 failure. Arızalı klavye denetleyicisi Bkz.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Error 8602 Auxiliary Device Failure. Fare veya klavye kablosu gevşektir veya düzgün takılmamıştır. Verify that mouse and keyboard are securely attached to correct connectors. Bozuk fare veya klavye. Fare veya klavye kablosunu yeniden takın. Fare veya klavyenin çalışır durumda olduğundan emin olun. Bkz. "USB Cihazlara Yönelik Sorun Giderme" sayfa 326. Manufacturing mode Sistem hatalı detected. yapılandırılmıştır.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Memory tests terminated by keystroke. Bellek testini sonlandırmak Yalnızca bilgi vermek içindir. için POST sırasında boşluk tuşu veya ESC tuşuna basılmıştır. Keyboard data line Klavye kablo konektörü failure. gevşek ya da düzgün Keyboard stuck key bağlanmamış. Klavye ya da klavye/fare denetleyicisi failure. arızalı olabilir. Klavyenin düzgün bağlandığından emin olun. Sorun devam ediyorsa, bkz. "Yardım Alma" sayfa 377.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Not a boot diskette. Önyüklenebilir bir disket değildir. Önyüklenebilir bir disket kullanın. PCI BIOS failed to Arızalı veya yanlış takılmış Ara kat kartını yeniden install. ara kat kartı. yerleştirin. Bkz. "G/Ç Modül Ara Kat Kartları" sayfa 232. Sorun devam ediyorsa, bkz. "Yardım Alma" sayfa 377. Plug & Play Configuration Error. PCI cihazını başlatma sırasında hatayla karşılaşıldı; arızalı blade kartı.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri Invalid configuration information please run SETUP program CMOS sağlama toplamı arızası. Sistem Kurulumu programını çalıştırın ve geçerli ayarları inceleyin. Bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149. Read fault. Arızalı disket, disket Disketi değiştirin. Sürücü sürücüsü veya optik sürücü. kablosunun düzgün bağlandığından emin olun. Sisteminize takılan uygun sürücüler için bkz.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri System service update required. iDRAC6 Enterprise kartı flaş belleği bozuk olabilir. ftp.dell.com ya da support.dell.com adresindeki en son sürümü kullanarak flash belleği geri yükleyin. Flash belleğin alan değişimi gerçekleştirme talimatları için iDRAC6 Kullanım Kılavuzu'na bakın. The amount of system memory has changed. Arızalı bellek modülü. Bkz. "Blade Belleğine Yönelik Sorun Giderme" sayfa 334. Sorun devam ediyorsa, bkz.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri TPM configuration operation is pending. Bu mesaj bir TPM İlerlemek için I veya M girin. yapılandırma komutu girildikten sonra sistem yeniden başlatıldığı zaman görüntülenir. Press (I) to Ignore OR (M) to Modify to allow this change and reset the system. Çözüm İşlemleri WARNING: Modifying could prevent security TPM configuration TPM yapılandırma işlem operation honored. komutu kabul edildi System will now reset Unsupported CPU combination.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Çözüm İşlemleri CPU set to minimum Gücün korunması için Bilerek yapılan bir ayar frequency. işlemci hızı kasıtlı olarak değilse, olası nedenler için düşük düzeyde ayarlanmış diğer mesajları kontrol edin. olabilir. Memory set to Gücün korunması için Bilerek yapılan bir ayar minimum frequency. bellek frekansı bilerek değilse, olası nedenler için düşük düzeyde ayarlanmış diğer mesajları kontrol edin. olabilir.
Tablo 1-27. Blade Mesajları (devamı) Mesaj Nedenleri Warning: The current memory configuration is not optimal. For more information on valid memory configurations, please see the Hardware Owner’ Manual on the technical support site. Bellek yapılandırma hatası Bkz. "Sistem Belleği" yok ancak bellek sayfa 186. yapılandırması Dell tarafından önerilmiyor. Unexpected interrupt in protected mode DIMM'ler yanlış takılmıştır veya klavye/fare denetleyici yongası arızalıdır. Write fault.
Uyarı Mesajları Bir uyarı mesajı, olası bir sorun olduğunda sizi uyarır ve sistem bir göreve devam etmeden önce yanıt vermenizi ister. Örneğin, bir disketi biçimlendirmeden önce, bir mesaj sizi disketteki tüm verileri kaybedebileceğinize dair uyarır. Uyarı mesajları genellikle görevi keser ve y (evet) veya n (hayır) yazarak yanıt vermenizi ister. NOT: Uyarı mesajları uygulama veya işletim sistemi tarafında oluşturulur. Daha fazla bilgi için, işletim sistemi veya uygulamayla birlikte gelen belgelere bakın.
Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi Sistem Kurulum programı, sistem donanımını yönetmenizi ve BIOS düzeyinde seçenekleri belirlemenizi sağlayan bir BIOS programıdır.
Sistem kurulum programının önyükleme ayarları ekranının Önyükleme Modu alanındaki önyükleme modunu seçersiniz (bkz. "Önyükleme Ayarları Ekranı" sayfa 157). Önyükleme modunu belirttikten sonra, sistem belirtilen önyükleme modunda önyükleme yapar ve bundan sonra işletim sisteminizi söz konusu modda kurmaya devam edebilirsiniz. Bundan sonra, kurulu işletim sistemine geçmek için aynı önyükleme modunda (BIOS ya da UEFI) sistemde önyükleme yapmalısınız.
Sistem Kurulumu Programı Kılavuz Tuşlarını Kullanma Tablo 2-1. Sistem Kurulum Programı Kılavuz Tuşları Tuşlar İşlem Yukarı ok ya da Bir önceki alana gider. Aşağı ok ya da Bir sonraki alana gider. Ara çubuğu, <+>, <–>, sol ve sağ Bir alandaki özellikler arasında geçiş yapar. Bazı oklar alanlarda, uygun değeri yazabilirsiniz. Sistem Kurulum programından çıkar ve herhangi bir değişiklik yapıldıysa sistemi yeniden başlatır.
Seçenek Açıklama Boot Settings Bkz. "Önyükleme Ayarları Ekranı" sayfa 157. (Önyükleme Ayarları) Integrated Devices (Tümleşik Aygıtlar) Bkz. "Tümleşik Aygıtlar Ekranı" sayfa 158. PCI IRQ Assignment (PCI IRQ Ataması) PCI veri yolundaki tümleşik birimlerin her birine ve IRQ gerektiren tüm genişletme kartlarına atanmış IRQ'yu değiştirmek için bir ekran görüntüler. Serial Communication Bkz. "Seri İletişim Ekranı" sayfa 160. (Seri İletişim) Power Management (Güç Yönetimi) Bkz.
Bellek Ayarları Ekranı Seçenek Açıklama System Memory Size (Sistem Bellek Boyutu) Sistem belleği miktarını görüntüler. System Memory Type (Sistem Bellek Türü) Sistem belleğinin türünü gösterir. System Memory Speed (Sistem Bellek Hızı) Sistem bellek hızını görüntüler. Sistem Bellek Voltajı (PowerEdge M915, M710HD) Sistem belleğinin geçerli işletim voltajını görüntüler. Video Memory (Video Belleği) Video belleği miktarını görüntüler.
Seçenek Açıklama Yedek Bellek (PowerEdge M915, M910, M905, M805 ve M605) Geçerli bir bellek yapılandırması gerçekleştirilirse, yedek belleği etkinleştirebilirsiniz. Seçenekler Yedek Mod ve Devre Dışı'dır. Düğümün Dönüşümlü Devre Dışı (varsayılan) olarak ayarlanırsa, NUMA kullanılır.
Seçenek Açıklama Mantıksal işlemci (Varsayılan Etkin) Etkin olarak ayarlandığında, işlemci çekirdeği için her iki mantıksal işlemci de etkinleştirilir. Devre Dışı olarak ayarlandığında, çekirdek başına yalnızca tek bir mantıksal işlemci etkinleştirilir. Sanallaştırma Teknolojisi (Varsayılan Devre dışı) NOT: Sisteminiz sanallaştırma yazılımı kullanmıyorsa bu özelliği devre dışı bırakın.
Seçenek Açıklama Number of Cores per Tümü seçeneğine ayarlanırsa, her bir işlemci içindeki tüm Processor (İşlemci çekirdekler etkinleştirilir. Başına Çekirdek Sayısı) (Varsayılan Tümü) Intel QPI Bant Genişliği Önceliği Hesaplamak için bant genişliği önceliğini ayarlar. Turbo Mode (Turbo Modu) İşlemci(ler) tarafından desteklenirse, Turbo Modu etkinleştirir ya da Devre Dışı bırakır. C1E (sadece M915) Etkin olarak ayarlandığında işlemci eylemsiz durumda minimum performansa geçer.
Önyükleme Ayarları Ekranı Seçenek Açıklama Önyükleme Modu (Varsayılan BIOS) (PowerEdge M915, M910, M710, M710HD, M610 ve M610x) İşletim sistemi Birleşik Genişletilebilir Bellenim Arabirimini (UEFI) destekliyorsa, bu seçeneği UEFI olarak ayarlayın. Bu alanın BIOS olarak ayarlanması, UEFI özelliği olmayan işletim sistemleri ile uyumluluk imkanı sağlar.
Tümleşik Aygıtlar Ekranı Seçenek Açıklama Integrated SAS Controller (Tümleşik SAS Denetleyicisi) veya Tümleşik RAID denetleyicileri (Varsayılan Etkin.) Tümleşik SAS veya RAID denetleyicisini etkinleştirir. User Accessible USB Sistemin USB Bağlantı Girişlerini etkinleştirir ya da devre Ports (Kullanıcı Erişimli dışı bırakır. Tüm Bağlantı Noktaları Açık veya Tüm USB Bağlantı Noktaları) Bağlantı Noktaları Kapalı seçenekleri bulunmaktadır.
Seçenek Açıklama Embedded NIC1 and NIC2 (Yerleşik NIC1 ve NIC2) (Varsayılan Etkin) Sistemin tümleşik NIC1 ve NIC2 denetleyicisini etkinleştirir ya da devre dışı bırakır. NOT: NIC1/NIC2 ve NIC3/NIC4 denetleyicilerini M710HD için etkinleştirebilir veya devre dışı bırakabilirsiniz. MAC Address (MAC Adresi) Özel bir tümleşik NIC için MAC adresini gösterir. Bu alanda kullanıcı tarafından seçilebilir ayarlar yoktur.
PCI IRQ Atamaları Ekranı Seçenek Açıklama Verilen aygıt için el ile bir IRQ seçmek için <+> ve <-> tuşlarını kullanın, ya da sistem başlangıcında BIOS'un bir IRQ değeri seçmesine izin vermek için Varsayılan'ı seçin. Seri İletişim Ekranı Blade IMC üzerinden konsolun yeniden yönlendirmesini etkinleştirebilecek tek bir seri bağlantı girişine sahiptir (COM1).
Güç Yönetimi Ekranı (Sadece PowerEdge M915, M910, M710, M710HD, M610 ve M610x) Seçenek Açıklama Power Management (Güç Yönetimi) Seçenekler: OS Control (İşletim Sistemi Denetimi), Active Power Controller (Etkin Güç Denetleyicisi), Custom (Özel) veya Maximum Performance (Maksimum Performans). OS Denetleyicisini, Aktif Güç Denetleyicisini, veya Statik Yönetim Performansını seçerseniz, BIOS bu ekranda kalan seçenekleri önceden yapılandırır.
Sistem Güvenlik Ekranı Seçenek Açıklama System Password (Sistem Parolası) Parola güvenlik özelliğinin durumunu gösterir ve yeni bir parola ataması ve doğrulamasına imkan sağlar. NOT: Daha fazla bilgi için, bkz. "Sistem Parolası Kullanma" sayfa 166. Setup Password (Kurulum Parolası) Bir kurulum parolası kullanarak Sistem Kurulumuna erişimi kısıtlar. NOT: Daha fazla bilgi için, bkz. "Sistem Parolası Kullanma" sayfa 166.
Seçenek Açıklama TPM Clear (TPM Temizleme) (Varsayılan Yok) NOT: TPM'nin temizlenmesi, TPM'deki tüm şifreleme anahtarlarının kaybolmasına neden olur. Bu seçenek, işletim sisteminin önyükleme yapmasını engeller ve şifreleme anahtarları geri döndürülemezse veri kaybına sebep olur. Bu seçeneği etkinleştirmeden önce TPM anahtarlarını yedekleyin. Evet seçeneği seçildiğinde, tüm TPM içerikleri temizlenir. NOT: Bu alan, TPM Security (TPM Güvenliği) Kapalı olarak ayarlandığında salt okunurdur.
UEFI Önyükleme Yöneticisine Giriş 1 Sisteminizi açın veya yeniden başlatın. 2 Aşağıdaki mesajı gördüğünüzde tuşuna basın: = UEFI Boot Manager NOT: USB klavye etkinleşene kadar sistem yanıt vermez. NOT: Sistem Kurulumundaki Önyükleme Modu Seçeneği UEFI Önyükleme Yöneticisine erişmek için UEFI olarak ayarlanmalıdır. tuşuna basmadan önce işletim sisteminiz yüklenmeye başladıysa, sistemin önyükleme işlemini bitirmesine izin verin ve sisteminizi yeniden başlatarak tekrar deneyin.
UEFI Önyükleme Ayarları Ekranı Seçenek Açıklama Add Boot Option Yeni bir önyükleme seçeneği ekler. (Önyükleme Seçeneği Ekle) Delete Boot Option Var olan önyükleme seçeneğini siler. (Önyükleme Seçeneğini Sil) Enable/Disable Boot Option Önyükleme seçenek listesindeki önyükleme seçeneğini (Ön Yükleme Seçeneğini etkinleştirir ya da devre dışı bırakır. Etkinleştir/Devre Dışı Bırak) Önyükleme Seçeneğini Değiştir Önyükleme seçenek listesinin sırasını değiştirir.
Sistem ve Kurulum Parolası Özellikleri Sisteminiz sistem şifresi özelliği etkinleşmeden ilerler. Sistemi yalnızca sistem şifresi koruması varken çalıştırın. NOT: Parola özellikleri, sisteminizdeki veriler için temel düzeyde güvenlik sağlar. NOT: Sisteminiz çalışıyor ve gözetimsiz durumdaysa, sisteminizde depolanan verilere herkes erişebilir. Sistem Parolası Kullanma Bir sistem parolası atandığında, sistem başladıktan sonra parolayı sorar ve yalnızca parolayı bilenler sistemin tamamını kullanabilir.
3 Yeni sistem parolanızı yazın. Parolanızda 32 adete kadar karakter kullanabilirsiniz. Parolayı yazarken alanda yer tutucular gözükür. Parola ataması büyük/küçük harf duyarlı değildir. Mevcut tuş kombinasyonları geçersizdir ve bunları girerseniz sistem sesli uyarı verir. Bir karakter silmek için ya da sol ok tuşuna basın. NOT: Sistem parolası atamadan alandan çıkmak için, bir diğer alana ilerlemek üzere tuşuna basın ya da tamamlamadan önce tuşuna basın adım 5.
Parola güvenliğini devre dışı bırakmak için: 1 tuşlarına basarak, sisteminizi açın ve yeniden başlatın. 2 Parolanızı girin ve tuşlarına basın. Password Status (Parola Durumu) Locked (Kilitli) olduğunda, yeniden başlatma sırasında istendiğinde parolayı girip tuşuna basmalısınız. Yanlış bir sistem parolası girildiğinde, sistem bir mesaj görüntüler ve parolanızı yeniden girmenizi ister. Doğru parolayı girmek için üç hakkınız vardır.
Kurulum Parolasını Kullanma Kurulum Parolası Atama Kurulum parolasını, yalnızca Setup Password (Kurulum Parolası) Not Enabled (Etkin Değil) durumundayken atayabilirsiniz. Kurulum parolası atamak için, Setup Password (Kurulum Parolası) seçeneğini vurgulayın ve <+>ya da <–> tuşlarına basın. Sistem, parolayı girmenizi ve doğrulamanızı ister. NOT: Kurulum parolası sistem parolası ile aynı olabilir. İki parola farklıysa, kurulum parolası alternatif bir sistem parolası olarak kullanılabilir.
Mevcut Sistem Şifresini Silme veya Değiştirme 1 Sistem Kurulum programına girin ve System Security (Sistem Güvenliği) seçeneğini belirtin. 2 Setup Password (Kurulum Parolası) seçeneğini vurgulayın ve kurulum parolası penceresine erişmek için tuşuna basın. Mevcut kurulum parolasını silmek için tuşuna iki kez basın. Ayar Not Enabled (Etkin Değil) olarak değişir. 3 Yeni bir kurulum parolası belirlemek istiyorsanız, "Kurulum Parolası Atama" sayfa 169 bölümündeki adımları gerçekleştirin.
Blade Bileşenlerinin Takılması Önerilen Araçlar Bu bölümdeki prosedürleri yapmak için aşağıdaki öğelere ihtiyaç duyabilirsiniz. • 1 ve 2 numaralı Phillips tornavidalar • T8 ve T10 Torx tornavidalar • Bilek topraklama şeridi Bir Blade'in Çıkarılması ve Takılması Bir Blade'in Çıkarılması 1 OS komutlarını ya da CMC'yi kullanarak blade'i kapatın ve blade'in güç kaynağının kapalı olduğundan emin olun. Blade kapatıldığında, ön panel güç göstergesi kapalı konumda olur. Bkz. Şekil 1-13.
Şekil 3-1.
Şekil 3-2.
Bir Blade'in Takılması 1 Eğer yeni bir blade takıyorsanız, G/Ç konektörlerinden plastik kapağı çıkarın ve gelecekte kullanmak üzere saklayın. Bkz. Şekil 3-3. 2 Kolu blade'in sol tarafına getirmek için blade'in yerini ayarlayın. 3 Eğer sekiz üst yuvadan birine bir blade takıyorsanız, blade'in üst kenarındaki kılavuz rayını, kasanın üzerindeki plastik kılavuzların arasına oturması için hizalayın.
Bir Boş Blade Kartının Takılması 1 Boş blade kartını kılavuz rayı yukarı bakacak şekilde tutun (Ayrıntılar için bkz. Şekil 3-1). 2 Boş blade kartını kasaya takma: • Eğer boş blade kartını sekiz üst yuvadan birine takıyorsanız, boş blade kartının üst kenarındaki metal kılavuz rayını kasadaki plastik kılavuzlar arasına oturacak şekilde hizalayın (Ayrıntılar için bkz. Şekil 3-1).
Şekil 3-3. 1 Blade'i Açma (PowerEdge M600 Gösterilmektedir) 2 1 G/Ç konektör kapağı 3 kasa kapağı 3 2 kapağı serbest bırakma mandalı Blade'i Kapama 1 Blade'in içinde hiçbir aracın ya da parçanın kalmadığından emin olun. 2 Kasanın kenarındaki dişleri, kapağın iç kısmındaki kapak hizalama pimleriyle aynı hizaya getirin. 3 Bu kapak serbest bırakma mandalının tamamıyla açık olup olmadığını kontrol edin ve kapağı kasanın üzerine indirin.
Sistemin İçerisi Şekil 3-4 ila Şekil 3-12 blade'lerin içindeki iç bileşenleri göstermektedir. Şekil 3-4.
Şekil 3-5.
Şekil 3-6.
Şekil 3-7.
Şekil 3-8.
Şekil 3-9.
Şekil 3-10.
Şekil 3-11.
Şekil 3-12.
Sistem Belleği Sistem Belleği - PowerEdge M915 Sistem kartın kanal başına iki LV DIMM, işlemci başına dört kanal şeklinde organize edilen 32 bellek yuvasına sahiptir. Bu yapılandırma, aşağıda belirtilen maksimum bellek yapılandırmalarına izin verir: Her kanal için 1 GB, 2 GB, 4 GB, 8 GB ve 16 GB LV DIMM olmak üzere toplamda 512 GB'a kadar desteklenir. Tek aşamalı, çift aşamalı ve üç aşamalı RDIMM'ler desteklenir.
Şekil 3-13.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M915 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki yönergelere uyun: DİKKAT: Düzgün hava akışının sağlanması için bellek modülü kapakları kullanılmayan bellek soketlerine takılmalıdır. 188 • Bellek modülleri, her bellek modülünde ilk iki soketle başlamak üzere çift olarak monte edilmelidir. Bu soketler beyaz sabitleme kollarıyla işaretlenir. • Her işlemcinin bellek yapılandırması aynı olmalıdır.
Tablo 3-1. PowerEdge M915 Bellek Yapılandırması Örnekleri NOT: DIMM'ler A1-A8, işlemci 1'e, DIMM'ler B1-B8 işlemci 2'ye, vb. atanmıştır.
Toplam İşlemci Fiziksel Sayısı Bellek Bellek Modülleri – Sayı ve Tür 96 GB On altı 4 GB ve On N altı 2 GB Dört Bellek Bellek Modülü Konumları Yedekle me Desteği A1, A2, A3, A4, A5, A6, A7, A8, B1, B2, B3, B4, B5, B6, B7, B8, C1, C2, C3, C4, C5, C6, C7, C8, D1, D2, D3, D4, D5, D6, D7, D8 NOT: 4-GB bellek modülleri x1, x2, x3 ve x4 numaralı yuvalara,takılmalı ve 2-GB bellek modülleri x5, x6, x7 ve x4 numaralı yuvalarına takılmalıdır.
Toplam İşlemci Fiziksel Sayısı Bellek Bellek Modülleri – Sayı ve Tür 192 GB On altı 8 GB ve On N altı 4 GB Dört Bellek Bellek Modülü Konumları Yedekle me Desteği A1, A2, A3, A4, A5, A6, A7, A8, B1, B2, B3, B4, B5, B6, B7, B8, C1, C2, C3, C4, C5, C6, C7, C8, D1, D2, D3, D4, D5, D6, D7, D8 NOT: 8-GB bellek modülleri x1, x2, x3 ve x4 numaralı yuvalara,takılmalı ve 4-GB bellek modülleri x5, x6, x7 ve x8 numaralı yuvalarına takılmalıdır.
Uygun Olmayan Bellek Yapılandırması Bellek yapılandırmanız yukarıda belirtilen yönergelere uygun değilse, bu durum sistemin performansını etkileyebilir. Sisteminiz başlatılırken, bellek yapılandırmanızın uygun olmadığını belirten bir hata mesajı görüntüleyebilir. Bellek Yedekleme Desteği - PowerEdge M915 Bellek yedekleme özelliği ayrıca System Setup (Sistem Kurulumu) programının Memory Information (Bellek Bilgileri) ekranında etkinleştirilmelidir. Bkz. "Bellek Ayarları Ekranı" sayfa 153.
Şekil 3-14.
Genel Bellek Modülünü Takma Yönergeleri - PowerEdge M910 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken aşağıdaki yönergelere uyun: • Bellek modülleri, her bellek modülünde ilk iki soketle başlamak üzere çift olarak monte edilmelidir. Bu soketler beyaz sabitleme kollarıyla işaretlenir. • Her işlemcinin bellek yapılandırması aynı olmalıdır. • Bellek modülleri aynı boyut, hız ve lock-step (kilit adım) çifti teknolojisine (aynı renkli kollar) sahip olmalıdır.
Tablo 3-2. PowerEdge M910 Bellek Yapılandırması Örnekleri (devamı) Toplam Fiziksel Bellek Bellek Modülleri Bellek Modülü Konumları – Sayı ve Tür 128 GB Sekiz 16 GB 160 GB Yirmi dört 4 GB ve A1, A2, A3, A4, A5, A6, A7, A8, B1, B2, B3, B4, B5, Sekiz 8 GB B6, B7, B8, C1, C2, C3, C4, C5, C6, C7, C8, D1, D2, D3, D4, D5, D6, D7, D8 A1, A2, B1, B2, C1, C2, D1, D2 NOT: 8-GB bellek modülleri düşük numaralı x1, x2 yuvalarına ve 4-GB bellek modülleri x3, x4, x5, x6, x7, x8 yuvalarına takılmalıdır.
Uygun Olmayan Bellek Yapılandırması Bellek yapılandırmanız yukarıda belirtilen yönergelere uygun değilse, bu durum sistemin performansını etkileyebilir. Sisteminiz başlatılırken, bellek yapılandırmanızın uygun olmadığını belirten bir hata mesajı görüntüleyebilir. Bellek Yedekleme Desteği - PowerEdge M910 Bellek yedekleme (yedekleme bankası) Tablo 3-3'de gösterilen bellek yapılandırmalarından birine sahip sistemlerde desteklenir.
Şekil 3-15. Bellek Konumları - PowerEdge M905 B1 D1 D2 D3 D4 B8 C1 C2 C3 C4 A8 A1 Genel Bellek Modülü Montaj Yönergeleri – PowerEdge M905 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki yönergelere uyun: • Bellek modülleri, her bellek modülünde ilk iki soketle başlamak üzere çift olarak monte edilmelidir. Bu soketler beyaz sabitleme kollarıyla işaretlenir. • Blade içerisindeki tüm bellek modülleri hız ve teknoloji açısından aynı olmalıdır.
Tablo 3-4 desteklenen bellek yapılandırmalarını gösterir. DİKKAT: Düzgün hava akışının sağlanması için bellek modülü kapakları kullanılmayan bellek soketlerine takılmalıdır. Tablo 3-4.
Uygun Olmayan Bellek Yapılandırması Bellek yapılandırmanız yukarıda belirtilen yönergelere uygun değilse, bu durum sistemin performansını etkileyebilir. Sisteminiz başlatılırken, bellek yapılandırmanızın uygun olmadığını belirten bir hata mesajı görüntüleyebilir. Bellek Yedekleme Desteği - PowerEdge M905 Bellek yedekleme (yedekleme bankası) Tablo 3-5'de gösterilen bellek yapılandırmalarından birine sahip sistemlerde desteklenir.
Şekil 3-16.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M805 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki yönergelere uyun: • Bellek modülleri A1 ve A2 (işlemci 1) ve B1 ve B2 yuvalarından başlanarak aynı boyuttaki DIMM çiftleri halinde takılmalıdır. Bu yuvalar beyaz ejektör tırnaklarıyla işaretlenir. • Blade içerisindeki tüm bellek modülleri hız ve teknoloji açısından aynı olmalıdır. Her çift içerisindeki bellek modülleri aynı boyutta olmalıdır.
Tablo 3-6.
Tablo 3-7. Bellek Yedekleme Yapılandırmaları - PowerEdge M805 NOT: Eğer 16 özdeş bellek modülü takılırsa bellek yedekleme desteklenir.
Şekil 3-17.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M710 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken aşağıdaki yönergelere uyun: • RDIMM'ler ve UDIMM'ler karma kullanılamaz. • Bellek modülleri işlemcinin en uzağındaki soketten başlanmak üzere yerleştirilir (bu soket beyaz soket serbest bırakma kolu ile belirtilir). • Çift işlemci yapılandırmasında, tüm işlemcilerin bellek yapılandırması aynı olmalıdır.
Bağımsız Kanal Modu (Optimize Edici Mod) - PowerEdge M710 Bu modda, üç kanalın tümü aynı bellek modülleriyle doldurulur. Bu mod daha büyük toplam bellek kapasitesine izin verir, ancak diğer modların güvenirlik özelliklerini desteklemez. Bu modu etkinleştirmek için, Sytem Setup (Sistem Kurulumu) programının Memory Settings (Bellek Ayarları) ekranında bulunan Optimizer (İyileştirici) seçeneğini seçin. Bkz. "Bellek Ayarları Ekranı" sayfa 153.
Tablo 3-8.
Tablo 3-8.
Sistem Belleği - PowerEdge M710HD Sisteminiz DDR3 tescilli DIMM'leri (RDIMMler) desteklemektedir. On sekiz bellek soketi, her kanalda üç DIMM ile işlemci başına üç kanal içerisinde organize edilmiş şekilde sistem kartı üzerinde yer alır. Bu yapılandırma toplam 192 GB'a karşılık olarak her kanal için en fazla üç 2 GB, 4 GB, 8 GB ve iki 16 GB RDIMM destekler. Tek aşamalı, çift aşamalı ve üç aşamalı RDIMM'ler desteklenir. Şekil 3-18.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M710HD Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken aşağıdaki yönergelere uyun: • Bellek modülleri işlemcinin en uzağındaki soketten başlanmak üzere yerleştirilir (bu soket beyaz soket serbest bırakma kolu ile belirtilir). • Çift işlemci yapılandırmasında, tüm işlemcilerin bellek yapılandırması aynı olmalıdır. • Eğer üç aşamalı bellek modülleri takılırsa, her kanal başına maksimum iki DIMM desteklenir.
Bellek Yedekleme Desteği - PowerEdge M710HD NOT: Bellek yedekleme desteği için sisteminize Intel Xeon 5600 serisi işlemciler takılmalıdır. Bellek yedekleme (yedekleme bankası) Tablo 3-9'de gösterilen bellek yapılandırmalarından birine sahip sistemlerde desteklenir. Bellek yedekleme özelliği ayrıca System Setup (Sistem Kurulumu) programının Memory Information (Bellek Bilgileri) ekranında etkinleştirilmelidir. Bkz. "Bellek Ayarları Ekranı" sayfa 153.
Tablo 3-9.
Tablo 3-9.
Sistem Belleği - PowerEdge M610/M610x Sisteminiz DDR3 kayıtlı DIMM'leri (RDIMMS) ya da ara belleksiz DIMM'leri (UDIMM'ler) destekler. Sistem kartında aşağıda belirtilen maksimum bellek yapılandırmalarına izin veren on iki bellek soketi yer almaktadır: • Toplam 192 GB olacak şekilde 1 GB, 2 GB, 4 GB, 8 GB ve 16 GB kapasiteli RDIMM'ler (varsa) desteklenir. Tek aşamalı, çift aşamalı ve üç aşamalı RDIMM'ler desteklenir. • 1 GB ve 2- GB UDIMM toplam 24 GB'a karşılık olarak desteklenir. Şekil 3-19.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M610/M610x Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken aşağıdaki yönergelere uyun: • RDIMM'ler ve UDIMM'ler karma kullanılamaz. • Bellek modülleri işlemcinin en uzağındaki soketten başlanmak üzere yerleştirilir (bu soket beyaz soket serbest bırakma kolu ile belirtilir). • Çift işlemci yapılandırmasında, her bir işlemci için yapılan bellek yapılandırması aynı olmalıdır.
Bağımsız Kanal Modu (Optimize Edici Mod) - PowerEdge M610/M610x Bu modda, üç kanalın tümü aynı bellek modülleriyle doldurulur. Bu mod daha büyük toplam bellek kapasitesine izin verir, ancak diğer modların güvenirlik özelliklerini desteklemez. Bu modu etkinleştirmek için, Sytem Setup (Sistem Kurulumu) programının Memory Settings (Bellek Ayarları) ekranında bulunan Optimizer (İyileştirici) seçeneğini seçin. Bkz. "Bellek Ayarları Ekranı" sayfa 153.
Tablo 3-10.
Tablo 3-10.
Şekil 3-20. Bellek Konumları - PowerEdge M605 A1 A2 A3 A4 B4 B3 B2 B1 Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M605 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki yönergelere uyun: • Bellek modülleri A1 ve A2 (işlemci 1) ve B1 ve B2 (işlemci 2, takılıysa) yuvalarından başlanarak aynı boyuttaki DIMM çiftleri halinde takılmalıdır. Bu yuvalar beyaz ejektör tırnaklarıyla işaretlenir.
Tek İşlemci Bellek Yapılandırmaları DİKKAT: Düzgün hava akışının sağlanması için bellek modülü kapakları kullanılmayan bellek soketlerine takılmalıdır. Tablo 3-11.
Çift İşlemcili Bellek Yapılandırmalar DİKKAT: Düzgün hava akışının sağlanması için bellek modülü kapakları kullanılmayan bellek soketlerine takılmalıdır. Tablo 3-12.
Uygun Olmayan Bellek Yapılandırması Bellek yapılandırmanız yukarıda belirtilen yönergelere uygun değilse, bu durum sistemin performansını etkileyebilir. Sisteminiz başlatılırken, bellek yapılandırmanızın uygun olmadığını belirten bir hata mesajı görüntüleyebilir. Bellek Yedekleme Desteği - PowerEdge M605 Bellek yedekleme Tablo 3-13'da gösterilen bellek yapılandırması tamamen doldurulmuş olan tek veya çift işlemcili sistemlerde desteklenir.
Tablo 3-13.
Sistem Belleği - PowerEdge M600 Sistem belleğinizi, 667-MHz kayıtlı DDRII tam arabellekli DIMM'ler (FBD'ler) takarak maksimum 32 GB'a yükseltebilirsiniz. 512 MB, 1 GB, 2 GB, 4 GB ve 8 GB bellek modülleri desteklenir. Bellek modülü soketleri iki eşit dala ayrılır (0 ve 1). Her dal iki kanaldan ve her kanal iki bellek modülü soketinden oluşur: • Dal 0, Kanal 0, 1 ve 5 numaralı soketten oluşur. • Dal 1, Kanal 0, 2 ve 6 numaralı soketten oluşur. • Dal 1, Kanal 2, 3 ve 7 numaralı soketten oluşur.
Genel Bellek Modülü Montaj Yönergeleri - PowerEdge M600 Sisteminizden en yüksek performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki yönergelere uyun: • Bellek modülleri, aynı boyutlu DIMM çiftleri şeklinde takılmalıdır. Toplam bellek modülü sayısı iki, dört ya da sekize eşit olmalıdır. Altı modül desteklenmez. • Blade içerisindeki tüm bellek modülleri hız ve teknoloji açısından aynı olmalıdır. Her çift içerisindeki bellek modülleri aynı boyutta olmalıdır.
Uygun Olmayan Bellek Yapılandırması Bellek yapılandırmanız yukarıda belirtilen yönergelere uygun değilse, bu durum sistemin performansını etkileyebilir. Sisteminiz başlatılırken, bellek yapılandırmanızın uygun olmadığını belirten bir hata mesajı görüntüleyebilir. Bellek Yedekleme Desteği - PowerEdge M600 Bellek yedekleme için sekiz tane aynı bellek modülü gereklidir.
Bellek Modüllerini Takma UYARI: Blade kapatıldıktan sonra bir süre bellek modülleri dokunulamayacak kadar sıcak kalır. Bellek modüllerini ellemeden önce soğumaları için bir süre bekleyin. Bellek modüllerini kart kenarlarından tutun ve bileşenlerine dokunmaktan kaçının. 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Bellek modülü soketlerini oturtun. Bkz. Şekil 7-13 veya Şekil 7-12.
6 Bellek modülünün kenar konektörünü bellek modülü soketindeki hizalama dişi ile aynı hizaya getirin ve bellek modülünü sokete yerleştirin. NOT: Bellek modülünde, bellek modülünü sokete sadece tek bir şekilde takabilmenizi sağlayan bir hizalama dişi bulunmaktadır. 7 Bellek modülünü sokete kilitlemek için bellek modülünün üzerine başparmaklarınızla bastırın.
Bellek Modüllerini Çıkarma UYARI: Blade kapatıldıktan sonra bir süre DIMM'ler dokunulamayacak kadar sıcak kalır. DIMM'leri ellemeden önce soğumaları için bir süre bekleyin. DIMM'leri kart kenarlarından tutun ve DIMM bileşenlerine dokunmaktan kaçının. 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Bellek modülü soketlerini oturtun. Bkz. Şekil 7-13 veya Şekil 7-12.
4 Kablo yönetim klipsini kasa iç duvarından çıkarın. Bkz. Şekil 3-12. 5 Mandaldaki çıkıntılı yere baş parmağınızla bastırarak ve mandalın ucunu kaldırarak kart sabitleme mandalını açın. Bkz. Şekil 3-23. NOT: Ara kat arabirim kartını yalnızca kenarlarından tutun. 6 Arabirim kartını sistem kartından yukarı doğru kaldırın. 7 Kart sabitleme mandalını kapatın. 8 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176.
Şekil 3-23.
Ara Kat Arabirim Kartının Takılması 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Mandaldaki çıkıntılı yere baş parmağınızla bastırarak ve mandalın ucunu kaldırarak kart sabitleme mandalını açın. Bkz. Şekil 3-23. 4 Varsa, konektör kapağını arabirim kart yuvasından çıkarın. NOT: Ara kat arabirim kartını yalnızca kenarlarından tutun.
Ara Kart Kurulum Kuralları Tam Yüksekliğe sahip Blade'ler Tam yüksekliğe sahip blade'ler dört adete kadar ara kat kartı desteklerler. NOT: PowerEdge M610x bir tam blade sistemi olmasına rağmen, genişletme yuvasında sadece iki ara kat kartı yuvası (MEZZ1_Fab_C1 ve MEZZ2_FAB_B1) kullanıma uygundur. Sistem kartındaki diğer iki yuva (MEZZ1_FAB_C and MEZZ2_FAB_B) PCIe genişletme kartı yükselticisi ve sistem kartı arasında bağlantı sağlayan ara kat arabirim kartı tarafından kullanılır.
• PowerEdge M710 dört yuvanın tümünde SFF ve LFF ara kat kartlarını destekler. x8 PCIe Gen 1ve x4 PCIe Gen 2 kartları desteklenir. • PowerEdge M610x iki küçük form faktörü (SFF) ara kat kartını destekler. x8 PCIe Gen 1 ve x8 PCIe Gen 2 kartları desteklenir. Yarı Yüksek Blade'ler Yarı-yüksek blade'ler iki adet ara kat kartı desteklerler: • Ara kat kartı, C yuvası Yapı C'yi destekler. Bu kartın G/Ç modülü C1 ve C2 yuvalarına takılan G/Ç modülü yapı tipi ile de eşleşmesi gerekmektedir.
Şekil 3-24.
Şekil 3-25. Bir Ara Kart Takma ve Çıkarma - Yarı Yüksekliğe Sahip Blade'ler 3 4 2 5 1 1 Yapı C ara kart yuvası 2 Yapı B ara kart yuvası 3 ara kart 4 ara kat kartı konektörü 5 sabitleme mandalı 4 Varsa, konektör kapağını ara kart yuvasından çıkarın. NOT: Ara kartı yalnızca kenarlarından tutun. 5 Ara kartlar kart yuvasına sığacak şekilde tasarlanmışlardır. Ara kartın altındaki konektörü ilgili blade kartındaki soket ile aynı hizaya getirmek için kartı döndürün.
6 Kartı tam olarak yerleşene ve kartın dış kenarındaki plastik klips blade kasasının üst kısmına yerleşene kadar yerine doğru indirin. 7 Ara kartı sabitlemek için sabitleme mandalını kapatın. 8 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 9 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. Ara Kartın Çıkarılması 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175.
Şekil 3-26. SD Kartın Takılması ve Çıkarılması (PowerEdge M905 ve M805) 1 1 2 SD Kart 2 SD kart konektörü PowerEdge M915, M910, M710, M710HD, M610 ve M610x Bu blade'lerde, SD kart yönetilmeyen bir sürekli depolama kartıdır. Bu kart kullanılarak bir hipervizör kurulabilir.
1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 SD kartı aşağı kısımdaki kart yuvasına takın. Bkz. Şekil 3-27. 3 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. Şekil 3-27.
SD vFlash Kartı (Sadece PowerEdge M915, M910, M710, M710HD, M610 ve M610x) NOT: PowerEdge M915, M910 ve M710HD için, iDRAC6 vFLASH kart, SD kart ile birlikte sistem kurulumda Integrated Devices (Tümleşik Aygıtlar) ekranındaki Redundancy (Yedekleme) seçeneğini Mirror (Aynalama) moduna getirerek IDSDM işlevine ayarlanabilir. IDSDM işlevi etkin hale getirildiğinde iDRAC6 VFlash kartlarının VFLash işlevselliği devre dışı bırakılır.
RAID Pil Bu bölümdeki bilgiler tümleşik bir pil yedekleme birimi olmayan isteğe bağlı PERC denetleyici kartlı sistemler için geçerlidir. NOT: PowerEdge M710, M610 ve M610x için RAID pil konektörleri sistem kartında bulunur. Sistem kartındaki RAID pil için konektörleri bulmak üzere "Sistem Kartı Konektörleri" sayfa 355 bölümündeki uygun şekle bakın. Bir RAID Pilin Çıkarılması 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Sistemi açın. Bkz. "Blade'i Açma" sayfa 175.
Şekil 3-29.
Şekil 3-30.
Şekil 3-31.
Şekil 3-32.
RAID Pilinin Takılması 1 Pili takın. Pil taşıyıcılı sistemler için: a RAID pilini, pil taşıyıcıya takın. Bkz. Şekil 3-29. b Pil taşıyıcıdaki tırnakları kasadaki pil taşıyıcı yuvaları ile hizalayın. c Pil taşıyıcıyı yerine oturana kadar pil taşıyıcı yuvalarına doğru itin. Bkz. Şekil 3-29. PowerEdge M910 için, sistem kartındaki pil taşıyıcısındaki RAID pilinin üzerindeki tırnakları sabitlemek için pili kaydırın (bkz. Şekil 3-30).
Tümleşik NIC Donanım Anahtarı Blade’in tümleşik NIC'leri için donanım işlevselliği bir sistem kartındaki sokete NIC donanım anahtarı takılarak etkin hale getirilebilir (bkz. "Sistem Kartı Konektörleri" sayfa 355.) NOT: Ayrıca tam NIC işlevselliği için işletim sistemi desteği gereklidir. Şekil 3-33.
Dahili USB Anahtarı (Sadece PowerEdge M915, M910, M710, M710HD, M610 ve M610x) Bu blade'ler bir USB flaş bellek anahtarı için dahili bir USB konektör sağlar. USB bellek anahtarı bir önyükleme aygıtı, güvenlik anahtarı veya yığın depolama aygıtı olarak kullanılabilir. Dahili USB konektörünü kullanmak için, Sistem Kurulum programındaki Integrated Devices (Tümleşik Aygıtlar) ekranında Internal USB Port (Dahili USB Bağlantı Noktası) seçeneği etkinleştirilmelidir.
Ağ Ek Kartı/LOM Yükseltici Kart (Sadece PowerEdge M915 ve M710HD) LOM Yükseltici Kartı Çıkarma 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 LOM yükseltici kartı sistem kartına sabitleyen üç vidayı sökün. Bkz. Şekil 3-35. 4 Kartı sistem kartından kaldırın. 5 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 6 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. Şekil 3-35.
LOM Yükseltici Kartını Takma 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Ağ Ek Kartını takın: a Kartı, kart konektörü sistem kartındaki ilgili konektöre yerleşene kadar yerine doğru indirin. Bkz. Şekil 3-35. b Kartı üç vidayla sabitleyin. 4 Kartı sistem kartına sabitlemek için vidaları sıkıştırın. Bkz. Şekil 3-35. 5 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 6 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174.
Genişletme Kartını Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-36.
10 Kabloları genişletme kartına bağlayın. Bkz. Şekil 3-37 ve Şekil 3-38. NOT: Kablo yönetim klipsiyle genişletme kartı yükselticisini ara kat arabirim kartına bağlayan veri kablolarını, blade'i kapattığınız zaman kasa kapağının engel olmadan kaydığından emin olmak üzere yönlendirin. Bkz. Şekil 3-37. 11 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 12 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174.
7 Kartı kalıcı olarak çıkartıyorsanız, kasadaki boş genişletme kartı yuva açıklığının üzerine bir metal dolgu desteği takın. NOT: Sistemin Federal İletişim Komisyonu (FCC) sertifikasının geçerliliğini koruması için boş genişletme yuvasına dolgu desteği takmanız gerekir. Destekler toz ve kiri sistemden uzak tutar ve bilgisayarın düzgün soğutulmasına ve sistemin içerisindeki hava akışına yardımcı olur.
Şekil 3-37.
Şekil 3-38.
4 Kasa iç duvarından çıkarmak için empedans duvarını sol kısmından yukarı kaldırın, daha sonra empedans duvarını genişletme kartı yükselticisinin üzerindeki yuvadan dışarı kaydırın. Bkz. Şekil 3-36. 5 Genişletme kartı yükselticisini yükseltici kılavuzundan direklerinden ve sistemden dışarı kaldırın. Bkz. Şekil 3-39. Şekil 3-39.
Genişletme Kartı Yükselticisini Takma 1 Yükseltici kılavuzlarını genişletme kartı yükselticisinin her bir ucunda sistem kartındaki yükseltici kılavuzu direkleri ile hizalayın ve yükseltici sistem kartına tam olarak yerleşene kadar yükselticiyi blade'e indirin. Bkz. Şekil 3-39. 2 Varsa, genişletme kartlarını yeniden takın. Bkz. "Genişletme Kartını Takma" sayfa 251. 3 Güç ve veri kablolarını yükseltici konektörlere bağlayın: Bkz. Şekil 3-37 ve Şekil 3-38.
PowerEdge M805 Sistemi • PowerEdge M805 sadece çift veya dört çekirdekli AMD Opteron 2xxxx serisi işlemcileri destekler. • İki işlemcinin kurulması gerekir; tek işlemcili yapılandırmalar desteklenmez. • Hypertransport (HT) köprü kartlarının CPU3 ve CPU4 yuvalarına takılır. Bkz. "HT Köprü Kartı (Yalnızca PowerEdge M905)" sayfa 278.
Şekil 3-40. Isı Emicinin Kurulması ve Çıkarılması (PowerEdge M915) 1 2 3 6 5 4 1 ısı emici 2 vidalar (4) NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-41. Isı Emicinin Kurulması ve Çıkarılması (PowerEdge M910) 1 2 3 4 6 5 NOT: Yukarıdaki çizim 130 W ısı emiciyi gösterir. 95 W / 105 W ısı emiciler Şekil 3-42'de gösterilen ısı emici ile benzer. 1 ısı emici 2 vidalar (4) NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-42. Isı Emicinin Kurulması ve Çıkarılması (PowerEdge M905) 1 2 3 4 6 5 1 ısı emici 2 vidalar (4) NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-43. Isı Emicinin Takılması ve Çıkarılması (PowerEdge M805) 1 2 3 4 1 ısı emici 2 vidalar (4) 4 soket CPU1 NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-44. Isı Emicinin Takılması ve Çıkarılması (PowerEdge M710) 1 2 3 4 1 ısı emici 2 vidalar (4) 4 soket CPU1 NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-45. Isı Emicinin Takılması ve Çıkarılması (PowerEdge M710HD) 1 4 3 2 1 soket CPU2 2 vidalar (2) 3 ısı emici 4 soket CPU1 NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-46. Isı Emicinin Takılması ve Çıkarılması (PowerEdge M610) 1 4 3 2 1 soket CPU2 2 ısı emici NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-47. Isı Emicinin Takılması ve Çıkarılması (PowerEdge M610x) 1 2 4 3 1 ısı emici 2 vidalar (4) 4 soket CPU1 NOT: Isı emiciyi burada gösterilen yönde takmanız gerekir.
Şekil 3-48.
Şekil 3-49.
4 Isı emiciyi çıkarın: Termal gresi kirletmesini önlemek için ısı emiciyi çalışma zemininde ters döndürün. 5 Termal gresi işlemcinin veya koruyucunun yüzeyinden temizlemek için temiz ve tiftiksiz bir bez kullanın. 6 PowerEdge M910 için, işlemci koruyucusunu serbest bırakmak için vidayı çıkarın ve ardından işlemciyi soketten çıkarın. Bkz. Şekil 3-51. Diğer blade'ler için, soket serbest bırakma kolunu işlemci soketten çıkana kadar yukarı doğru çekin.
Şekil 3-50.
Şekil 3-51.
Şekil 3-52.
Şekil 3-53.
İşlemciyi Takma 1 Kullanılmayan bir sokete bir işlemci ekliyorsanız, ilk önce aşağıdaki işlemi gerçekleştirin: NOT: Yalnızca bir işlemci takıyorsanız CPU1 soketine takılmalıdır. Bkz. Şekil 7-13 veya Şekil 7-12. a İşlemci dolgu kapağını çıkarın. b Plastik işlemci soket kapağını soketten çıkarın. c PowerEdge M910 için, işlemci koruyucusunu sabitleyen vidayı sökün.
c İşlemci korumasını kapatın. d PowerEdge M910 için, işlemci koruyucusunu sabitleyen vidayı sıkın. Diğer blade'ler için yerine oturana ve işlemciyi sabitleyene kadar soket serbest bırakma kolunu aşağı döndürün. 3 Isı emicisini takın: a Isı emicisini yeniden kuruyorsanız, ısı emicideki termal gresi temizlemek için temiz, tiftiksiz bir bez kullanın. Bir işlemciyi yükseltiyorsanız ve işlemci ile birlikte yeni bir ısı emici tedarik edilmişse yeni ısı emicisini kurun.
6 System Setup (Sistem Kurulumu) programına girmek için tuşuna basın ve işlemci bilgisinin yeni sistem yapılandırması ile uyumlu olduğunu doğrulayın. Sistem Kurulum programının kullanımı hakkında talimatlar için, bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149. 7 Yeni işlemcinin düzgün çalıştığını doğrulamak için sistem tanılama araçlarını çalıştırın. Tanı programlarını çalıştırma ve işlemciler ile ilgili sorun giderme hakkında bilgi için, bkz.
2 FlexMem Köprüsünü sokete takın. DİKKAT: Kartı yanlış bir şekilde takmak sistemi çalıştırdığınızda karta ve sisteme kalıcı hasar verebilir. LGA soket üzerindeki pimleri eğmemeye dikkat edin. a İşlemcinin bir köşesinde bulunan altın sarısı küçük üçgeni konumlandırarak işlemcinin pim-1 köşesini tanımlayın. Bu köşeyi, sistem kartında karşılık gelen üçgen tarafından tanımlanan ZIF soketi köşesinin olduğu köşeye yerleştirin.
Şekil 3-54. Bir HT Köprü Kartı Takma ve Çıkarma (PowerEdge M905) 1 4 2 3 1 soket serbest bırakma kolu 2 işlemci koruyucusu 3 karttaki çentik 4 HT köprü kartı HT Köprü Kartını Takma 1 Sistem kartındaki soketi hazırlamak için aşağıdaki işlemleri gerçekleştirin: a İşlemci dolgu kapağını çıkarın. b Plastik işlemci soket kapağını soketten çıkarın. c Soket serbest bırakma kolunu açın ve 90 derece yukarı kaldırın. d İşlemci koruyucusunu kaldırın.
2 Köprü kartını sokete takın. Bkz. Şekil 3-54. DİKKAT: Kartı yanlış bir şekilde takmak sistemi çalıştırdığınızda karta ve sistem kartına kalıcı hasar verebilir. LGA soket üzerindeki pimleri eğmemeye dikkat edin. a İşlemcinin bir köşesinde bulunan altın sarısı küçük üçgeni konumlandırarak işlemcinin pim-1 köşesini tanımlayın. Bu köşeyi, sistem kartında karşılık gelen üçgen tarafından tanımlanan ZIF soketi köşesinin olduğu köşeye yerleştirin.
4 Konektöründen yukarı doğru kaldırarak pili çıkarın. Bkz. Şekil 3-55. Pili blade kartına yerleştirmek için bkz. Şekil 7-1 (PowerEdge 915), Şekil 7-2 (PowerEdge 910), Şekil 7-3 (PowerEdge M905), Şekil 7-4 (PowerEdge M805), Şekil 7-5 (PowerEdge M710), Şekil 7-6 (PowerEdge M710HD), Şekil 7-7 (PowerEdge M610), Şekil 7-8 (PowerEdge M610x), Şekil 7-12 (PowerEdge M605) veya Şekil 7-13 (PowerEdge M600). 5 Yeni pili "+" yazan tarafı yukarı bakacak şekilde yerleştirin. Bkz. Şekil 3-55. Şekil 3-55.
Sabit Sürücüler • PowerEdge M915 iki 2.5 inç'lik SAS veya SSD sabit disk sürücüsünü destekler. • PowerEdge M910 iki adete kadar 2,5 inç'lik SAS, SATA veya katı durum diski (SSD) sabit sürücülerini destekler. • PowerEdge M905 ve M805 bir veya iki adet 2,5 inç'lik SAS sabit sürücüsünü destekler. • PowerEdge M710 dört adete kadar 2.5 inç'lik SAS sabit sürücüyü destekler. • PowerEdge M710HD blade bir veya iki 2,5 inç'lik SAS veya SSD sabit sürücüyü destekler.
Bir Sabit Sürücü Takma NOT: Takılıp çıkarılabilen bir yedek sabit disk takılı iken ve blade açıkken, sabit disk otomatik olarak yeniden oluşturmaya başlar. Yedek sabit diskin boş olduğundan veya üstüne yazmayı isteyebileceğiniz bilgiler içerdiğinden emin olun. Yedek sabit diskte bulunan bütün bilgiler sabit disk kurulduktan hemen sonra silinir. NOT: Bütün işletim sistemleri çalışırken değiştirilebilen sabit sürücü kurulumunu desteklemez. İşletim sisteminiz ile birlikte gelen belgelere bakın.
3 Kol blade'e temas edene kadar sürücü taşıyıcıyı yuvanın içine itin. 4 Taşıyıcıyı yerine kilitlenene kadar yuvanın içine doğru iterken taşıyıcı kolunu kapalı konuma gelecek şekilde çevirin. Sürücü doğru şekilde takılırsa durum LED göstergesinde devamlı bir yeşil ışık görünür. Sürücü yeniden kurulurken sürücü taşıyıcı LED'i yeşil göstergesi yanıp söner. Sabit Sürücüyü Çıkarma NOT: Bütün işletim sistemleri çalışırken değiştirilebilen sabit sürücü kurulumunu desteklemez.
Önyükleme Sürücüsünün Yapılandırması Sistemin önyüklediği sürücü veya cihaz, Sistem Kurulum programında belirtilen sıra tarafından belirlenir. Bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149. Sabit Sürücünün Sabit Sürücü Taşıyıcısından Çıkarılması Taşıyıcının yan raylarındaki vidaları sökün ve sabit diski taşıyıcıdan ayırın. Bkz. Şekil 3-57.
Şekil 3-57.
Video Denetleyicisi (Yalnızca PowerEdge M905, M805, M605 ve M600) Video denetleyicisi takmak ve çıkarmak için aşağıdaki işlemleri takip edin: 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Video denetleyicisini çıkarın: • Bir PowerEdge M605, M805 veya M905'den video denetleyicisi çıkarıyorsanız, iki torks vidasını sökün ve kartı blade'den çıkarın. Bkz. Şekil 3-59.
Şekil 3-59. Video Denetleyici Ek Kartı Takma ve Çıkarma (PowerEdge M605 Gösterilmektedir) 1 2 3 1 video denetleyici kart 3 sistem kartındaki konektör 2 torks vidaları (2) 4 Yeni bir video denetleyicisi takmak için: 288 • Bir PowerEdge M600'e bir video denetleyicisi takıyorsanız, yükseltme kartındaki kenar konektörünü sistem kartındaki konektör ile hizalayın ve ardından yükseltme kartı konektör tamamen yerleşip mandal yerine oturana kadar indirin. Bkz. Şekil 3-58.
Sabit Sürücü Arka panel NOT: Blade disksiz yapılandırma ile çalışırken bile düzgün hava akışının sağlanması için, her blade'e bir sabit sürücü arka paneli takılmalıdır. NOT: PowerEdge M600, M610, M610x, M710, M710HD, M805, M905 ve M910 bir adet ve PowerEdge M915 iki adet sabit sürücü arka paneline sahiptir. Sabit sürücü arka panelinin yerini belirlemek için bkz. "Sistemin İçerisi" sayfa 177. Sabit sürücü arka paneli takma ve çıkarma işlemleri için aşağıdaki işlemleri gerçekleştirin: 1 Blade'i sökün. Bkz.
Şekil 3-60. Sabit Sürücü Arka Panelinin Çıkarılması ve Takılması (M915 Gösterilmiştir) 2 3 4 1 5 1 sabit sürücü arka paneli (2) 2 sabit sürücü konektörleri (2) 3 tutma kancaları (4) 4 mandallar (4) 5 arka panel konektörü (2) 5 Sabit sürücü arka panelini takmak için: 290 a Arka paneli sürücü konektörleri sabit sürücü yuvalarına bakacak şekilde tutun. b Arka paneli, sürücü yuvasının kenarındaki sabitleme kancaları arka panelde karşılık gelen yuvalar ile hizaya gelecek şekilde yerleştirin.
6 Sabit sürücüyü / sürücüleri değiştirin. Birden fazla sürücü takıyorsanız orijinal yerlerine taktığınızdan emin olun. 7 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 8 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. Blade Sistem Kartı Sistem Kartını Çıkarma 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Kartın arkasındaki G/Ç konektörü/konektörlerine bir G/O konektör kapağı takın. UYARI: İşlemci ve ısı emici aşırı ısınabilir.
a Sistem kartı sabitleme pimini kaldırmak için sağ elinizin baş parmağını ve işaret parmağını kullanın. Bkz. Şekil 3-61. b İşaret parmağınız ile sabitleme pimini yukarıda tutarak sistem kartını kasanın açık olan ucundan dışarı doğru kaydırmak için blade kasasının köşesine baş parmağınız ile bastırın. Şekil 3-61.
Yarı yüksekliğe sahip blade sistem kartını çıkarmak için, blade kasasını bir elinizle tutun, sistem kartı sabitleme mandalını diğer elinizle kaldırın ve itin ve ardından sistem kartını kasanın açık olan ucundan dışarı kaydırın. Bkz. Şekil 3-62. Şekil 3-62.
10 G/Ç konektör kapağının hala kartın arkasındaki G/Ç konektördeki yerinde olduğundan emin olun. Bkz. Şekil 3-61 veya Şekil 3-62. 11 Video yükseltme kartını veya ek kartı çıkarın. Bkz. "Video Denetleyicisi (Yalnızca PowerEdge M905, M805, M605 ve M600)" sayfa 287. 12 Bellek modüllerini ve bellek modül kapaklarını çıkarın. Bkz. "Bellek Modüllerini Çıkarma" sayfa 229. 13 İşlemciyi /işlemcileri çıkarın. Bkz. "İşlemciyi Çıkarma" sayfa 259. 14 Depolama denetleyici kartını çıkarın. Bkz.
2 Yeni sistem kartını sabitleme mandalı veya sabitleme pimi yerleşene kadar kasanın açık olan ucuna doğru kaydırın. NOT: Sistem kartı plakasının kasa ile paralel olduğundan emin olun. Kart aksamı doğru bir şekilde takıldığında, sistem kartındaki tırnaklar blade kasasının zemininde karşılık gelen açıklıklara oturur. Bkz. Şekil 3-61 veya Şekil 3-62. 3 Video ek kartı veya video yükseltme kartını yeniden takın. Bkz. "Video Denetleyicisi (Yalnızca PowerEdge M905, M805, M605 ve M600)" sayfa 287.
5 Bir RAID denetleyicisini çıkarıyorsanız RAID pilinin denetleyici kartı ile bağlantısını kesin. 6 Denetleyici kartını dik olarak sistem kartından ayırın. Şekil 3-63.
Merkez Hat Arabirim Kartı (PowerEdge M610x) Merkez hat arabirim kartı PCIe kartlarını kullanma özelliği sunan ek bir kasa seçeneğidir. Merkez Hat Arabirim Kartının Çıkarılması 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 Kartın arkasındaki G/Ç konektörü/konektörlerine bir G/O konektör kapağı takın. 4 Varsa, her iki ara kat kartını çıkartın. Bkz. "Ara Kartın Çıkarılması" sayfa 237.
Şekil 3-64. Merkez Hat Arabirim Kartını Takma ve Çıkarma PowerEdge M610x 1 2 4 3 1 vidalar (2) 2 güç kablosu konektörleri (3) 3 merkez hat arabirim kartı 4 veri kablosu konektörleri (2) 6 Güç ve veri kablolarını merkez hat arabirim kartındaki konektörlerden sökün. Güç ve veri kablolarının bağlantısını kesmek için, konektör üzerindeki serbest bırakma mandalına basın, içeri doğru hafifçe itin, daha sonra kablo konektörünü kart konektöründen serbest bırakmak için dışarıya itin.
Merkez Hat Arabirim Kartının Takılması 1 Merkez hat arabirim kartını kasanın arkasından kaydırarak blade kasasına konumlandırın. 2 Merkez hat arabirim kartını kasaya sabitleyen vidaları sıkın. Bkz. Şekil 3-64. NOT: Merkez hat arabirim kartının kasaya paralel olduğundan emin olun. 3 Güç ve veri kablolarını merkez hat arabirim kartındaki konektörlere bağlayın. 4 Ara kartını/kartlarını yeniden orijinal yerlerine takın. Bkz. "Bir Ara Kart Takma" sayfa 234. 5 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176.
Blade Bileşenlerinin Takılması
Kasa Bileşenlerini Kurma NOT: Doğru çalışma ve soğutmayı sağlamak için kasa içerisindeki tüm yuvalar ya bir modül ile ya da bir kapak ile her zaman dolu tutulmalıdır. Güç Kaynağı Modülleri M1000e kasası, kasanın arka panelinden erişilebilen çalışırken çıkarılıp takılabilme özellikli altı adete kadar güç kaynağı modülünü destekler. NOT: 2360-W ve 2700 W güç kaynağı modülleri PDU'dan 200-240 V giriş gerektirir.
CMC modülü sisteme yönelik güç yönetimini kontrol eder. Güç bütçesini, artıklığı ve tüm kasanın dinamik gücünü yapılandırmak için CMC'yi programlayabilirsiniz (Kasa, sunucular, G/Ç modülleri, iKVM, CMC, ve güç kaynakları). Güç yönetimi servisi güç tüketimini iyileştirir ve gerçek zamanlı isteğe dayalı farklı modüller arasında güç tekrar paylaştırır. Daha fazla bilgi için, bkz. Dell Kasa Yönetim Denetleyicisi Kullanım Kılavuzu'ndaki "Güç Yönetimi".
Şekil 4-1. Güç Kablosu Sabitleme Klipsi 2 1 3 4 5 1 güç kaynağı 2 sabitleme klipsi bağlama 3 Güç kaynağı sapındaki çıkıntı 4 sabitleme klipsi 5 güç kablosu 2 Saptaki güç kaynağı modülü kilit düğmesinde aşağı basınız. Bkz. Şekil 4-2.
Şekil 4-2. Bir Güç Kaynağı Modülünü kurma ya da kaldırma. 1 2 3 1 güç kaynağı 3 serbest bırakma düğmesi 2 sap 3 Güç kaynağı modülünü çıkarmak için güç kaynak modülü kolunu aşağıya doğru döndürün. 4 Güç kaynağı modülünü kasadan dışarıya doğru kaydırın.
Bir Güç Kaynağı Modülünü Kurma 1 Güç kaynağı modülü sapının tam olarak açık olduğundan ve güç kablosunun elektrik prizine takılı olmadığından emin olun. 2 Güç kaynağı modülünü kasaya doğru kaydırın. Bkz. Şekil 4-2. 3 Güç kaynağı modülü kolunu tutturana kadar yukarıya doğru döndürün. 4 Güç kaynağı modülüne bir güç kablosu bağlayınız. 5 Sabitleme klipsini kablonun üzerine geçirerek kabloyu sabitleme klipsiyle güç kaynağına bağlayın ve sabitleme klipsini güç kaynağı kolundaki çıkıntıya geçirip bağlayın. Bkz.
Şekil 4-3. Bir Fan Modülü Kaldırma ve Kurma 1 2 1 fan modülü 2 serbest bırakma düğmesi Bir Fan Modülü Kurma 1 Fanı kasaya kurmadan önce kir ve toz birikimine karşı gözden geçiriniz. 2 Fan modülünü tam olarak yerleşene ve kilit düğmesi oturana kadar kasadan içeri doğru kaydırın. Bkz. Şekil 4-3.
CMC Modülü Bir CMC modülünü Kaldırma 1 CMC modülüne bağlı olan kabloları çözün. 2 Kolun üzerindeki serbest bırakma mandalına basın ve kolu modül ön panelinden öteye çevirin. 3 Güç kaynağı modülünü kasadan dışarıya doğru kaydırın. 4 G/Ç konektör kapağını kurun. Bkz. Şekil 4-4. Şekil 4-4.
CMC Modülüne SD Kart Takma CMC modülündeki SD kart yuvası yuvaya bağlı WWN/MAC'lere blade kurulumunu ve değişimini kolaylaştırarak blade'ler için izin sağlayan isteğe bağlı bir WWN/MAC özelliğini destekler. NOT: Yedek CMC modül sistemi için, pasif modüle SD kartı takın. Pasif modülde mavi durum göstergesi kapalıdır. 1 CMC modülünü M1000e kasasından çıkarın. Bkz. "Bir CMC modülünü Kaldırma" sayfa 307. NOT: Yazma koruma mandalının açık ("unlock") konumda olduğundan emin olun.
3 CMC modülünü yeniden kurun ve bağlantısı kopmuş tüm kabloları yeniden bağlayın. Bkz. "Bir CMC Modülü kurma" sayfa 309. Tek bir CMC sisteminde, SD kart otomatik olarak etkinleşir. Yedek CMC modül sistemleri için, pasif modülü aktif hale getirmek için aşağıdaki aşamalardan geçerek bir değişim başlatın: 1 Chasis (Kasa) sayfasına gidin. 2 Power Management (Güç Yönetimi) sekmesine tıklatın. 3 Control (Kontrol) alt sekmesine tıklatın. 4 Reset CMC (CMC'yi Sıfırla) (sıcak akış) tuşunu seçin.
iKVM Modülü İKVM Modülünü Çıkarma 1 İKVM modülüne bağlı olan kabloları çözün. 2 Kolun üzerindeki serbest bırakma mandalına basın ve kolu ön paneldeki modülden öteye çevirin. Bkz. Şekil 4-4. 3 Modülü kasadan dışarıya doğru kaydırın. Bir iKVM Modülü Kurma 1 Modül kolunun tamamen açık olduğundan emin olun. Bkz. Şekil 4-4. 2 Kol kasayla temas edene kadar modülü kasaya doğru kaydırın. 3 Modülü tamamen yerleştirmek için, serbest bırakma mandalı yerine oturuncaya kadar kolu kapatın.
Şekil 4-6. Bir G/Ç modülünü Çıkarma ve Kurma 1 2 3 4 1 G/Ç konektör kapağı 2 G/Ç modülü 3 serbest bırakma mandalı 4 sap Bir G/Ç Modülünü Çıkarma NOT: G/Ç modülü uygun G/Ç yuvasında kurulmalıdır. Bkz. "G/Ç Modüllerinin Takılmasına Yönelik Kılavuzlar" sayfa 57. 1 G/Ç modülünü paketinden çıkarın ve kurulum için hazırlayın. Talimatlar için, G/Ç modülüyle birlikte gelen belgelere bakınız. 2 G/Ç konektör kapağını modülün arkasından çıkarın. Bkz. Şekil 4-6.
4 G/Ç modülüne bağlı olması gereken tüm kabloları bağlayın. Kablo bağlantılarıyla ilgili bilgi için G/Ç modülüyle birlikte verilen belgelere bakın. Kabloları düzenlemek ve yönetmek için kablo sayıcılarını kullanma hakkında daha fazla bilgi için bkz. Raf Kurulum Kılavuzu. 5 Yeni G/Ç modülünü desteklemesi için, bir veya daha fazla blade'de denk bir yapı ara kat kartı takılı olmalıdır. Gerekliyse, ara kat kart(lar)ını şimdi takın. Bkz. "G/Ç Modül Ara Kat Kartları" sayfa 232.
Şekil 4-7. Çerçeveyi Çıkarma ve Takma 2 1 3 1 çerçeve 3 vidalar (8) 2 kasa Kasa Çerçevesini Takma 1 Vidaları kullanarak çerçeveyi kasaya takın. Bkz. Şekil 4-7. 2 Ribbon kablosunu LCD modülüne bağlayın ve kapak plakasını yeniden takın.
Kasa Merkez Hattı Ön Modül Kafesi Aksamını ve Merkez Hattı Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir.
Şekil 4-8. Ön Modül Kafes Aksamını Çıkarma ve Takma 2 1 3 1 Ön modül kafes aksamı 3 vidalar (4) 2 kasa NOT: Boş kafes aksamı 21 kg (47 lb) gelir. Kasadan kafes aksamını çıkarırken yardım alın. 9 Kafesi kasadan dışarıya doğru kaydırın. Bkz. Şekil 4-8. 10 Kontrol panel kablosunu konektörün her bir ucundaki küçük mandallara basarak merkez hattından ayırınız. 11 Merkez hattını ön kafes aksamının arkasına sabitleyen dört adet T-15 Torks vidasını sökün ve merkez hattını çıkarın. Bkz. Şekil 4-9.
Şekil 4-9. Merkez Hattı Çıkarma ve Takma 2 1 1 Ön modül kafes aksamı 3 vidalar (4) 3 2 merkez hat Merkez Hattı ve Ön Modül Kafes Aksamını Kurma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz.
4 Ön modül kafes aksamını sabitlemek için dört vidayı takın. 5 G/Ç modüllerini sökün. Bkz. "Bir G/Ç Modülünü Çıkarma" sayfa 311. 6 iKVM modülünü takın. Bkz. "Bir iKVM Modülü Kurma" sayfa 310. 7 CMC modülünü takın. Bkz. "Bir CMC Modülü kurma" sayfa 309. 8 Pervane modüllerini takın. Bkz. "Bir Fan Modülü Kurma" sayfa 306. 9 Güç kaynağı modüllerini takın. Bkz. "Bir Güç Kaynağı Modülünü Kurma" sayfa 305. 10 Blade'leri takın. Bkz. "Bir Blade'in Takılması" sayfa 174.
Şekil 4-10. Kontrol Panelini Çıkarma ve Takma 3 2 1 4 1 kontrol paneli 2 kontrol paneli kablosu 3 vidalar (2) 4 LCD panel kablosu 5 Kontrol panel kablosu konektörünün her bir ucundaki mandala basın ve kontrol paneli kablosunu panelin alt tarafından çıkarın. 6 LCD panel kablosunu kontrol panelinin altından çıkarmak için çekme tırnağını kullanın.
Kasa Kontrol Panelini Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 4-11. LCD modülünü Çıkarma ve Takma 3 4 5 2 1 1 kablo kapağı 2 LCD Modülü 3 ribbon kablosu 4 menteşeler (2) 5 vidalar (2) 2 Kablo kapağını çıkarın. 3 Ribbon kablosunu ayırın. 4 LCD modülünü menteşelere bağlayan iki vidayı sökün.
LCD Modülünü Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Kasa Bileşenlerini Kurma
Sisteminizde Sorun Giderme Önce Güvenlik—Sizin ve Sisteminiz için DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Donanım Kontrolü Bu bölümde monitör, klavye veya fare gibi sisteme takılan harici cihazlara ilişkin sorun giderme prosedürleri verilmektedir. Prosedürlerden herhangi birisini yürütmeden önce, bkz. "Harici Bağlantılara Yönelik Sorun Giderme" sayfa 324. Harici Bağlantılara Yönelik Sorun Giderme Sistem, monitör ve diğer çevre birimlerinde (klavye, fare veya diğer harici cihazlar) yaşanan sorunların en sık karşılaşılan sebebi genellikle gevşek ya da yanlış takılan kablolardır.
6 Monitörü çalıştığını bildiğiniz bir monitörle değiştirin. Monitör, blade ön panel konektörüne bağlandığında çalışmazsa, bu blade'in arızalı olduğu anlamına gelebilir. Bkz. "Yardım Alma" sayfa 377. iKVM modülüne bağlandığında monitör çalışmazsa, bu iKVM modülünün arızalı olduğu anlamına gelebilir. Bkz. "Yardım Alma" sayfa 377. Klavyeye Yönelik Sorun Giderme 1 Blade'in (blade'lerin) açık olduğundan emin olun. 2 iKVM belleniminin güncel olduğundan emin olun.
5 Kasa içerisine iki ya da daha fazla sayıda blade kuruluysa farklı bir blade seçin. Fare arka panel iKVM modülüne bağlıysa ve farklı bir blade'le çalışıyorsa ilk blade'in tekrar oturtulması gerekebilir. Bkz. "Bir Blade'in Çıkarılması ve Takılması" sayfa 171. Blade'i tekrar oturtmak yardımcı olmazsa bu blade'in arızalı olduğu anlamına gelebilir. Bkz. "Yardım Alma" sayfa 377. 6 Adım 3 Fareyi, çalıştığını bildiğiniz başka bir fare ile değiştirin, ardından adım 5 ve adımlarını tekrar edin.
Islak Kasaya Yönelik Sorun Giderme DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin. 1 Sistemi kapatın.
17 Sistemin doğru şekilde çalıştığını onaylamak için Sunucu Yöneticisi tanılama programını çalıştırın. Bkz. "Sistem Tanılamalarını Çalıştırma" sayfa 341. Sınamalar başarısız olursa, bkz."Yardım Alma" sayfa 377. Hasar Gören Kasaya Yönelik Sorun Giderme 1 Aşağıdaki bileşenlerin doğru şekilde takıldıklarından ve bağlandıklarından emin olun: • CMC modülü • iKVM modülü • G/Ç modülü • Güç kaynağı modülleri • Fan modülleri • Blade'ler 2 Tüm kabloların doğru şekilde takıldığından emin olun.
Kasa Bileşenlerine Yönelik Sorun Giderme Aşağıda belirtilen prosedürler, aşağıdaki bileşenlere yönelik nasıl sorun giderme uygulanacağını açıklamaktadır: • Güç kaynağı modülleri • Fan modülleri • CMC modülü • Ağ anahtarı modülü Güç Kaynağı Modüllerine Yönelik Sorun Giderme NOT: Güç kaynağı modülleri çalıştıkları sırada sisteme zarar vermeden değiştirilebilirler. Açılan bir sistemde bir seferde sadece bir tane güç kaynağı modülü sökün ve değiştirin.
3 Güç kaynaklarından hiçbirisinde arıza LED'i yanmıyorsa ve blade'ler açılmıyorsa, durum mesajları için LCD ekranı veya CMC'yi kontrol edin. 4 Sorun çözülmezse, bkz. "Yardım Alma" sayfa 377. Fan Modüllerine Yönelik Sorun Giderme NOT: Fan modülleri çalıştıkları sırada sisteme zarar vermeden değiştirilebilirler. Açılan bir sistemde bir seferde sadece bir tane fan modülü sökün ve değiştirin. Altı fanın tamamı çalıştırılmadan sistemin uzun süreler boyuca çalıştırılması sistemin aşırı ısınmasına yol açabilir.
2 CMC'nin (CMC'lerin) geçerli alt ağ IP adreslerine sahip olduklarından emin olun. ICMP ping komutunu kullanarak doğrulayın. NOT: İki CMC'nin takılı olduğu bir kasada her iki CMC de aynı IP adresini paylaşır. 3 CMC modülünü tekrar oturtun ve CMC modülü arıza göstergesinin sönüp sönmediğini kontrol edin. Modül göstergeleri ile ilgili daha fazla bilgi edinmek için "CMC Modülü" sayfa 307 ve Şekil 1-22 konularına başvurun. 4 Başka bir CMC modülü mevcutsa iki modülü değiştirin.
iKVM Modülüne Yönelik Sorun Giderme Sorun: iDRAC video\konsol yeniden yönlendirme kullanımı sırasında, Linux ile çalışan bir blade'e geçiş yapıldığında video, iKVM'den görüntülenemiyor. Olası Sebebi ve Çözümü: Kısa zaman önce daha düşük çözünürlüğe sahip olan bir monitör veya KVM uygulaması eklenmiştir. Örnek: Linux altında X Windows çalıştıran bir blade yerleştirilmiş ve açılmıştır.
Ağ Anahtarı Modülüne Yönelik Sorun Giderme NOT: Modül veya modüle bağlanan cihazlardan herhangi birisi ile ilgili bir donanım problemi olasılığını elemek için, öncelikle modülün doğru şekilde başlatıldığından ve yapılandırıldığından emin olun. Aşağıdaki prosedürü uygulamaya başlamadan önce Yapılandırma Kılavuzu'na ve modüller ile birlikte gelen belgelere başvurun. 1 Yapı tipine uygun bir G/Ç yuvasında bulunan modülü taktığınızdan emin olun. Bkz. "Desteklenen G/Ç Modülü Yapılandırma Ayarları" sayfa 62.
7 Blade belirli bir ağ anahtarı modülü için ara kat kartına ihtiyaç duyuyorsa, uygun ara kat kartının takılı olduğundan emin olun. Durum böyleyse, ara kat kartını tekrar oturtun. Bkz. "G/Ç Modül Ara Kat Kartları" sayfa 232. Blade üzerindeki ağ bağlantı göstergesi yeşil renkte yanıyorsa, blade uygun ağ anahtarı modülü için geçerli bir bağlantıya sahip demektir. 8 Uygun işletim sistemi sürücülerinin kurulu olduğundan ve protokol ayarlarının doğru iletişim sağlanması için yapılandırıldığından emin olun.
2 Sistem Kurulumu programına girin ve program ve sistem belleği ayarlarını kontrol edin. Bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149. Takılan bellek miktarı, sistem bellek ayarı ile eşleşirse, adım 8 adımına geçin. 3 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 4 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. DİKKAT: Blade kapatıldıktan sonra bir süre bellek modülleri dokunulamayacak kadar sıcak kalır.
3 Blade'i yeniden başlatın, Sistem Kurulum programına girin ve ardından sürücü denetleyicisinin etkinleştirildiğini onaylayın. Bkz. "Tümleşik Aygıtlar Ekranı" sayfa 158. 4 Gereksinim duyulan tüm cihaz sürücülerinin takılı olduklarından ve doğru şekilde yapılandırıldıklarından emin olun. NOT: Farklı bir yuvaya sabit sürücü takılması ayna durumunun optimal olması durumunda aynanın kırılmasına yol açabilir. 5 Sabit sürücüyü çıkartın ve diğer sürücü yuvasına takın. Bkz. "Sabit Sürücüler" sayfa 282.
4 Takılan genişletme kartlarının genişletme kartı takma yönergelerine uygun olduğundan emin olun. Bkz. "Genişletme Kartı Takma Yönergeleri" sayfa 250. 5 Genişletme kartının konektörüne sıkıca oturduğundan emin olun. Bkz. "Genişletme Kartını Takma" sayfa 251. 6 Blade'i kapatın. Bkz. "Blade'i Kapama" sayfa 176. 7 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. 8 Sorun çözülmezse, blade'i çıkarın. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 9 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175.
Sorun Giderme - İşlemciler 1 Blade'i sökün. Bkz. "Bir Blade'in Çıkarılması" sayfa 171. 2 Blade'i açın. Bkz. "Blade'i Açma" sayfa 175. 3 İşlemcinin (işlemcilerin) ve ısı emicisinin (emicilerinin) doğru şekilde takıldığından emin olun. Bkz. "İşlemciler" sayfa 258. 4 Sisteminize sadece bir işlemci takılıysa, bu işlemcinin ana işlemci yuvasına takıldığından emin olun. Bkz. Şekil 7-13 veya Şekil 7-12.
NVRAM Yedek Piline Yönelik Sorun Giderme Her blade'de, blade'i kapadığınızda NVRAM içinde blade yapılandırma ayarlarının, tarih ve saat bilgilerinin saklanmasını sağlayan bir pil bulunur. Önyükleme sırasında yanlış saat veya tarih görüntülenmesi durumunda pili değiştirmeniz gerekebilir. Blade'i herhangi bir pil takılı olmadan da çalıştırabilirsiniz; ancak bu durumda NVRAM içerisinde pil sayesinde saklanan blade yapılandırma bilgileri blade'in elektrik bağlantısı her kesildiğinde silinir.
Sisteminizde Sorun Giderme
Sistem Tanılamalarını Çalıştırma Blade'iniz ile ilgili bir sorun yaşarsanız, teknik yardımı aramadan önce tanılamaları çalıştırın. Tanılamaların amacı, ek ekipmana gerek duymadan veya veri kaybı riskine yol açmadan blade'inizin donanımını sınamaktır. Sorunu kendiniz çözemiyorsanız, servis ve destek personeli sorunu çözmenize yardımcı olmak için tanılama sınaması sonuçlarını kullanabilir.
Sistem Tanılama Özellikleri Sistem tanılama, özel aygıt grupları veya blade'deki aygıtlar için bir dizi menü ve seçenek sağlar.
Sistem Tanılamayı Çalıştırma Sistem tanılamaları Unified Server Configurator (USC - Birleşik Sunucu Yapılandırıcı) GUI veya bir USB flaş sürücüden çalıştırılabilir. NOT: Yalnızca blade'inizi sınamak için sistem tanılamayı kullanın. Sadece blade'iniz ile birlikte gelen programı (veya bu programın güncelleştirilmiş sürümünü) kullanın. Tümleşik Sistem Tanılamasını Çalıştırma Tümleşik sistem tanılama programı Unified Server Configurator (USC - Birleşik Sunucu Yapılandırıcı) ekranından çalıştırılır.
5 Sistem tanılama dosyalarını dizine kopyalayın. 6 Blade'e bağlı USB flaş sürücünüz olduğundan emin olun. 7 Sistem Kurulum programını girin ve (USB Flaş Sürücü Öykünme Türü) seçeneğinin Otomatik olarak ayarlandığından emin olun ve USB flaş sürücüyü Sabit Disk Sürücü Sırası seçeneğindeki ilk aygıt olarak ayarlayın. Talimatlar için bkz. "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149..
Sistem Tanılama Sınaması Seçenekleri Tanılama menüsünden bir seçenek seçmek için, seçeneği kopyalayın ve tuşuna veya seçenekteki vurgulan harfe karşılık gelen tuşa basın. Tablo 6-1 sınama seçeneklerin kısa bir açıklamasını verir. Tablo 6-1. Sistem Tanılama Sınaması Seçenekleri Sınama Seçeneği İşlev Hızlı Sınamalar Blade'in hızlı şekilde kontrolünü gerçekleştirir. Tüm Aygıtları Sına seçeneğini seçin ve ardından Hızlı Sınamalar seçeneği seçin.
Gelişmiş Sınama Seçeneklerini Kullanma Tanılama menüsünden Gelişmiş Sınama seçeneğini seçtiğinizde, tanılama ana ekranı görünür ve aşağıdaki bilgileri görüntüler. • Ekranın üstündeki iki satır tanılama yardımcı programını, sürüm numarasını ve sistem servisi etiket numarasını tanımlar. • Sınamaları Çalıştır alt menüsünün altında Tümü seçeneğini seçerseniz, Aygıt Grupları'nın altındaki ekranın sol tarafında sınandıkları sıraya göre tanılama aygıtları listelenir.
Sistem Kartı Bilgisi Blade Sistem Kartı Atlama Teli Ayarları DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Siz yalnızca ürününüzün belgelerinde belirtilen veya çevrimiçi ya da telefonla hizmet ve destek ekibi tarafından bildirilen sorun giderme veya basit onarım işlemlerini gerçekleştirmelisiniz. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
PowerEdge M910 Atlama Teli Ayarları Şekil 7-3 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-2 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-3 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-2. PowerEdge M910 Atlama Teli Ayarları PSWD_EN Parola özelliği etkinleştirilmiştir. (varsayılan) Parola özelliği devre dışı. NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M905 Atlama Teli Ayarları Şekil 7-3 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-3 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-3 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-3. PowerEdge M905 Atlama Teli Ayarları PSWD_EN Parola özelliği etkinleştirilmiştir. (varsayılan) Parola özelliği devre dışı. NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M805 Atlama Teli Ayarları Şekil 7-4 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-4 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-4 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-4. PowerEdge M805 Atlama Teli Ayarları PSWD_EN Parola özelliği etkinleştirilmiştir. (varsayılan) Parola özelliği devre dışı. NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M710 Atlama Teli Ayarları Şekil 7-5 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-5 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-5 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-5. PowerEdge M710 Atlama Teli Ayarları PWRD_EN Parola özelliği etkinleştirilmiştir. (Pim 2-3) (varsayılan) Parola özelliği devre dışı. (Pim 1-2) NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M710HD Atlama Teli Ayarları Şekil 7-6 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-6 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-6 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-6. PowerEdge M710HD Atlama Teli Ayarları PSWD_EN Parola özelliği etkinleştirilmiştir. (varsayılan) Parola özelliği devre dışı. NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M610/M610x Atlama Teli Ayarları Şekil 7-7 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-7 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-7 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-7. PowerEdge M610/M610x Atlama Teli Ayarları PWRD_EN (varsayılan) Parola özelliği etkinleştirilmiştir. (Pim 1-2) Parola özelliği devre dışı. (Pim 2-3) NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur.
PowerEdge M600 Atlama Teli Ayarları Şekil 7-13 Blade sistem kartındaki yapılandırma anahtarlarının konumunu gösterir. Tablo 7-8 atlama teli ayarlarını göstermektedir. NOT: Şekil 7-13 blade sistem kartının ön ucu sağ tarafa bakacak şekilde yönlendirilir. Tablo 7-8. PowerEdge M600 Atlama Teli Ayarları PWRD_EN (varsayılan) Parola özelliği etkinleştirilmiştir. (Pim 1-2) Parola özelliği devre dışı. (Pim 2-3) NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde tutulur (Pim 2-3).
Sistem Kartı Konektörleri PowerEdge M915 Sistem Kartı Şekil 7-1.
Tablo 7-9. PowerEdge M915 Sistem Kartı Konektörleri Konektör Açıklama 1 LOM YÜKSELTİCİ B Ağ Ek Kartı/LOM Yükseltici kart konektörü 2 B1 – B8 Bellek modülleri B1 – B8 (işlemci 2 için) 3 CPU2 İşlemci 2 soketi 4 CPU4 İşlemci 4 soketi 5 ARKA PANEL 2 Sabit sürücü arkapanel konektörü 6 - USB konektörü 7 D1 – D8 Bellek modülleri D1 – D8 (işlemci 4 için) 8 C1 – C8 Bellek modülleri C1 – C8 (işlemci 3 için) 9 - 3.
PowerEdge M910 Sistem Kartı Şekil 7-2. PowerEdge M910 Sistem Kartı Konektörleri 1 20 2 3 4 5 19 18 17 6 16 15 7 14 9 8 10 13 11 12 Tablo 7-10.
Tablo 7-10. PowerEdge M910 Sistem Kartı Konektörleri (devamı) Konektör Açıklama 6 D1 – D4 D1 – D4 bellek modülleri 7 - 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M905 Sistem Kartı Şekil 7-3. PowerEdge M905 Sistem Kartı Konektörleri 1 2 3 5 4 7 6 20 8 9 19 10 18 11 17 Tablo 7-11.
Tablo 7-11. PowerEdge M905 Sistem Kartı Konektörleri (devamı) Konektör Açıklama 8 C1 – C4 C1 – C4 bellek modülleri 9 PSWD_EN, NVRAM_CLR Sistem yapılandırma atlama telleri 10 - NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291. 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M805 Sistem Kartı Şekil 7-4. PowerEdge M805 Sistem Kartı Konektörleri 1 2 3 4 5 16 6 15 7 14 8 13 12 11 9 10 Tablo 7-12.
Tablo 7-12. PowerEdge M805 Sistem Kartı Konektörleri (devamı) 6 7 Konektör Açıklama PWRD_EN, NVRAM_CLR Sistem yapılandırma atlama telleri - NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291. 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M710 Sistem Kartı Şekil 7-5. PowerEdge M710 Sistem Kartı Konektörleri 2 1 3 5 4 6 17 7 8 16 9 15 10 14 13 12 11 Tablo 7-13.
Tablo 7-13. PowerEdge M710 Sistem Kartı Konektörleri (devamı) Konektör Açıklama 8 J_INT_USB USB konektörü 9 - 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M710HD Sistem Kartı Konektörleri Şekil 7-6. PowerEdge M710HD Sistem Kartı Konektörleri 1 2 10 3 9 8 4 7 6 5 Tablo 7-14. PowerEdge M710HD Sistem Kartı Konektörleri Konektör Açıklama 1 LOM YÜKSELTİCİ Ağ Ek Kartı/LOM Yükseltici kart konektörü 2 MEZZ2_FAB_B Ara kat kartı konektörü 2 Yapı C 3 A1 – A9 A1 – A9 bellek modülleri 4 CPU2 İşlemci 2 soketi 5 - 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M610 Sistem Kartı Şekil 7-7. PowerEdge M610 Sistem Kartı Konektörleri 4 3 2 1 13 12 5 6 11 13 10 9 8 7 Tablo 7-15.
Tablo 7-15. PowerEdge M610 Sistem Kartı Konektörleri (devamı) 9 Konektör Açıklama - Sabit sürücü arkapanel konektörü 10 B1 – B6 B1 – B6 bellek modülleri 11 - RAID pil konektörü 12 CPU1 İşlemci 1 soketi 13 - iDRAC6 Enterprise kart konektörü PowerEdge M610x Sistem Kartı Şekil 7-8.
Tablo 7-16. PowerEdge M610x Sistem Kartı Konektörleri Konektör Açıklama 1 MEZZ2_FAB_B Ara kat arabirim kart konektörü 2 A1 – A6 A1 – A6 bellek modülleri 3 - Tümleşik NIC özelliğini etkinleştirmek için donanım anahtarı soketi 4 CPU2 İşlemci 2 soketi 5 - Sabit sürücü arkapanel konektörü 6 - Depolama denetleyici kartı konektörü 7 - 3.0-V düğme pil konektörü NOT: Erişim için sistem kartının çıkarılması gerekir. Bkz. "Sistem Kartını Çıkarma" sayfa 291.
PowerEdge M610x Merkez Hattı Arabirim Kartı Şekil 7-9. PowerEdge M610x Merkez Hattı Arabirim Kartı Konektörleri 1 7 2 6 5 4 3 Tablo 7-17.
PowerEdge M610x Genişletme Kartı Yükseltici Şekil 7-10.
PowerEdge M610x Merkez Hattı Arabirim Kartı Şekil 7-11.
PowerEdge M605 Sistem Kartı Şekil 7-12. PowerEdge M605 Sistem Kartı Konektörleri 2 1 3 4 5 8 7 6 9 10 11 12 17 18 16 15 13 14 Tablo 7-18.
Tablo 7-18. PowerEdge M605 Sistem Kartı Konektörleri (devamı) Konektör Açıklama 12 Pil 3.0-V düğme pil konektörü 13 J_STORAGE (J_DEPOLAMA) Depolama denetleyici kartı konektörü 14 B1 Bellek modülü konektörü, yuva B1 15 B2 Bellek modülü konektörü, yuva B2 16 B3 Bellek modülü konektörü, yuva B3 17 B4 Bellek modülü konektörü, yuva B4 18 J_VIDEO Video denetleyici kart konektörü PowerEdge M600 Sistem Kartı Şekil 7-13.
Tablo 7-19. PowerEdge M600 Sistem Kartı Konektörleri Konektör Açıklama 1 - Ara kat kartı konektörü - Yapı C 2 - Ara kat kartı konektörü - Yapı B 3 Pil 3.0-V düğme pil konektörü 4 1 Bellek modülü konektörü, 1. yuva 5 5 Bellek modülü konektörü, 5. yuva 6 2 Bellek modülü konektörü, 2. yuva 7 6 Bellek modülü konektörü, 6. yuva 8 3 Bellek modülü konektörü, 3. yuva 9 7 Bellek modülü konektörü, 7. yuva 10 4 Bellek modülü konektörü, 4. yuva 11 8 Bellek modülü konektörü, 8.
Unutulan Şifreyi Devre Dışı Bırakma Blade'in yazılım güvenlik özellikleri bir sistem şifresi ve bir kurulum şifresini içerir. Bunlar "Sistem Kurulum Programı'nı kullanma ve UEFI Önyükleme Yöneticisi" sayfa 149 bölümünde ayrıntılı olarak incelenmiştir. Şifre atlama teli bu şifre özelliklerini etkinleştirir veya devre dışı bırakır ve kullanımdaki mevcut şifreleri siler. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
7 Blade'i takın. Bkz. "Bir Blade'in Takılması" sayfa 174. Blade açıkken, güç açık göstergesi sabit yeşildir. Blade'in önyüklemeyi bitirmesine izin verin. Mevcut parolalar sistem kaldırılan parolayla önyükleyene kadar devre dışı kalmaz (silinmez). Yine de, yeni bir sistem ve/veya kurulum parolası atamadan önce, parola anahtarını yeniden kurmalısınız. NOT: Kaldırılan anahtarla yeni bir sistem ve/veya kurulum parolası atarsanız, sistem bir daha ki önyüklemesinde yeni parolayı (parolaları) devre dışı bırakır.
Yardım Alma Dell ile İletişim Kurma ABD'deki müşterilerimiz 800-WWW-DELL (800-999-3355) numaralı telefonu arayabilir. NOT: Etkin bir Internet bağlantınız yoksa, iletişim bilgilerini satış faturanızda, irsaliyede, fişte veya Dell ürün kataloğunda bulabilirsiniz. Dell, çok sayıda çevrimiçi ve telefonla destek ve hizmet seçeneği sağlar. Bu hizmetlerin kullanılabilirliği ülkeye ve ürüne göre değişir; bölgenizde bazı hizmetler verilemiyor olabilir.
Yardım Alma
Dizin A ağ anahtarı modülü sorun giderme, 333 AC gücü mevcudiyet göstergesi, 40 açma blade'ler, 175 ara kat arabirim kartı, 229 ara kat kartı takma, 232 B başlangıç sistem özelliklerine erişim, 15 bellek sorun giderme, 334 takma, 227 bellek modülleri çıkarma, 229 blade'ler açma, 175 çıkarma, 171 işlemciler, 258 kapama, 176 takma, 174 Ç çıkarma bellek, 229 blade'ler, 171 boş blade kartı, 174 CMC modülü, 307, 310 fanlar, 305 G/Ç modülü, 310 genişletme kartı, 253 güç kaynakları, 302 pil, 280 sabit sürücü, 2
D Dell iletişim kurma, 377 Dell ile iletişim kurma, 377 destek Dell ile iletişim kurma, 377 donanımı kontrol etme, 324 F fan modülü göstergeleri, 40 fanlar çıkarma, 305 sorun giderme, 330 takma, 306 fare sorun giderme, 325 Fiber Kanal anahtarı modülü, 108, 110-112 Fiber Kanal geçiş modülü, 100, 104 genişletme yuvaları, 250 göstergeler AC gücü mevcut, 40 CMC arızası, 53 CMC bağlantı etkinliği, 53 CMC bağlantısı, 53 CMC durumu, 53 fan modülü, 40 Fiber Kanal geçiş modülü, 86, 88, 106, 112 güç kaynağı, 39 güç
iKVM modülü, 310 çıkarma, 310 özellikler, 45 sıralama, 47 takma, 310 N NVRAM yedek, 280 Ö önerilen araçlar, 171 K kapama blade'ler, 176 klavyeler sorun giderme, 325 konektörler sistem kartı, 355 kurulum şifresi özellikleri, 166 kurulum parolası, 169 L LOM yükseltici kartı, 249 M mesajlar blade, 127 durum LCD'si, 115 hata mesajları, 150 sistem tanılaması, 148 sistem yönetimi, 326 uyarı, 148 mini yüzey, 297 önyükleme sürücüsü yapılandırma, 285 özellikler arka panel, 37 blade, 25 blade güç düğmesi, 33 CM
POST sistem özelliklerine erişim, 15 PowerConnect Ethernet anahtarı modülü, 85-86, 94 Ş şifre devre dışı bırakma, 375 şifre özellikleri kurulum, 166 sistem, 166 S sistem güç göstergesi, 20 sistem kartı konektörler, 355 sistem kontrol paneli, 19 sistem kurulum programı SATA ayarları, 156 seri iletişim seçenekleri, 160 sistem güvenliği seçenekleri, 161 sistem kurulumu kullanma, 151 seçenekler, 151 sistem kurulumu ekranları konsol yeniden yönlendirme, 160 sistem güvenliği, 162 tümleşik aygıtlar, 158 sabit
sorun giderme (devamı) işlemciler, 338 klavye, 325 pil, 339 sabit sürücü, 335 sunucu modülü bileşenleri, 334 USB cihazları, 326 sunucu modülü bileşenleri sorun giderme, 334 sürücü taşıyıcı sabit sürücü, 285 T takma ara kat kartı, 232 bellek, 227 bellek yönergeleri, 188, 197, 201, 219 blade'ler, 174 CMC modülü, 309-310 fanlar, 306 G/Ç modülü, 311 genişletme kartı, 251 güç kaynakları, 305 pil, 280 sabit sürücüler, 283 sürücü taşıyıcısına sabit disk, 285 tanılama bkz.
Y yapılandırma önyükleme sürücüsü, 285 yardım alma, 377 yardım alma, 377 yönergeler bellek takma, 188, 194, 197, 201, 205, 210, 215, 219 genişletme kartı takma, 250 yuvalar Bkz. genişletme yuvaları.