Owners Manual
Table Of Contents
- Dell PowerEdge M830 (For Dell PowerEdge VRTX Enclosure) Owner's Manual
- Dell PowerEdge M830 (for PowerEdge VRTX) system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- UEFI iSCSI Settings
- System Security
- Secure Boot Custom Policy Settings
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing server module components
- Safety instructions
- Recommended tools
- Removing and installing a server module
- System cover
- Inside the server module
- Cooling shroud
- Processor blank and DIMM blank
- System memory
- PCIe mezzanine cards
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x12) SAS SSD backplane
- Installing a 1.8-inch (x12) SAS SSD backplane
- System battery
- Storage controller card
- Expander card
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Installing the NDC
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that came with the product.
1. Follow the safety guidelines listed in the Safety instructions section.
2. Follow the procedure listed in the Before working inside your system section.
3. Keep the #2 Phillips screwdriver ready.
4. Remove the NDC.
CAUTION: To prevent damage to the NDC, hold the card only by its edges.
NOTE: You must remove the NDC to replace a faulty NDC or service other components inside the system.
Steps
1. Align the following:
a. The slots on the card edge with the projection tabs on the plastic bracket covering the PCIe mezzanine card slots.
b. Screw holes on the card with the standoffs on the system board.
2. Lower the card into place until the card connector fits into the corresponding connector on the system board.
3. Secure the card with the two screws.
Figure 31. Installing the NDC
1.
slot on the NDC 2. screw (2)
3. NDC 4. standoff (2)
5. connector 6. tab projections
Next steps
1. Install the PCIe mezzanine card.
Installing server module components
89