Dell PowerEdge M1000e, M915, M910, M905, M805, M710HD, M710, M610x, M610, M605, and M600 Getting Started With Your System Guide de mise en route Primeiros passos com o sistema Procedimientos iniciales con el sistema
Dell PowerEdge M1000e, M915, M910, M905, M805, M710HD, M710, M610x, M610, M605, and M600 Getting Started With Your System Model BMX01, HHB Series, FHB Series
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this publication is subject to change without notice. © 2010 Dell Inc. All rights reserved.
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. This section describes the steps required to set up your system for the first time. Unpack the System Unpack your system and identify each item. Installing the Rails and System in a Rack Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your enclosure.
Installing the Blades Beginning at the top, slide the modules into the enclosure from left to right. When the blade is securely installed, the handle returns to the closed position. Connecting the CMC and KVM Modules Connect the serial cable and network cable(s) from the management system to the CMC module. If a second, optional CMC module is installed, connect it as well. Connect the keyboard, mouse, and monitor to the optional iKVM module.
Connecting the System to Power Connect the system’s power cables to the system power supplies. CAUTION: To prevent the power cables from being disconnected accidentally, use the plastic clip on each power supply to secure the power cable to the power supply, and use the Velcro strap to secure the cable to the strain-relief bar. Plug the other end of the power cables into a power distribution unit (PDU). CAUTION: Do not plug the power cables directly into a power outlet; you must use a PDU.
Turning On the System Press the power button on the enclosure. The power indicator should light. NOTE: Once you have connected the system to the power supplies, there may be a minimal delay before you can turn on your system. Turning On the Blades Press the power button on each blade, or power on the blades using the systems management software.
Complete the Operating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system. Supported Operating Systems Operating System M915 M910 Citrix XenServer 5.
Operating System M915 M910 Microsoft Windows Server 2008 Standard and Enterprise (x86) Editions with SP2 Microsoft Windows Server 2008 Standard, Enterprise, and Datacenter (x64) Editions Microsoft Windows Web Server 2008 (x64) Edition M905 M805 M710 M710HD M610 M610x Microsoft Windows Web Server 2008 (x64) Edition with SP2 Microsoft Windows Server 2008 R2 Standard, Enterprise, and Datacenter (x64) Editions Microsoft Windows Server
Operating System M915 M910 M905 M805 M710 M710HD M610 M610x Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions Microsoft Windows Server 2003 R2 Standard and Enterprise (x64) Editions Microsoft Windows Server 2003 R2 Datacenter (x64) Edition Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacenter (x64) Editions with SP2 M605 Red Hat Enterprise Linux AS, ES, and WS (version 4.
Operating System M915 M910 M905 M805 M710 Red Hat Enterprise Linux AS and ES (version 4.8) (x86_64) M710HD M610 Red Hat Enterprise Linux (version 5.0) (x86) Red Hat Enterprise Linux (version 5.0) (x86_64) Red Hat Enterprise Linux (version 5.2) (x86) Red Hat Enterprise Linux (version 5.5) (x86) Red Hat Enterprise Linux (version 5.5) (x86_64) Red Hat Enterprise Linux (version 6.
Operating System M915 M910 M905 M805 M710 M710HD M610 M610x VMware ESX version 4.0 Update 1 VMware ESXi version 4.0 Update 1 VMware ESX version 4.0 Update 2 VMware ESXi version 4.0 Update 2 VMware ESX version 4.1 Update 1 VMware ESXi version 4.1 Update 1 M605 —Supported NOTE: For the latest information on supported operating systems for all PowerEdge systems, see dell.com/ossupport.
Obtaining Technical Assistance If you do not understand a procedure in this guide or if the system does not perform as expected, see your Hardware Owner’s Manual. Dell offers comprehensive hardware training and certification. See dell.com/training for more information. This service may not be offered in all locations.
Memory (continued) PowerEdge M710HD DDR3 and DDR3L single-, dual-, and quad-rank memory modules, rated for1066 and 1333 MHz PowerEdge M710, M610x, M610, 800, 1066, or 1333 MHz DDR3 single- or dual-ranked registered DIMMs (RDIMMs) or unbuffered DIMMs (UDIMMs) or 800 or 1066 MHz DDR3 quad-ranked registered DIMMs (RDIMMs) or unbuffered DIMMs (UDIMMs) PowerEdge M600 FBD memory modules, rated for 677 MHz operation Memory module sockets PowerEdge M915, M910 32 240-pin sockets PowerEdge M905 24 240-pin so
Memory (continued) PowerEdge M805 4 GB (Four 1 GB memory modules) PowerEdge M710D 4 GB PowerEdge M710, M610x, M610 One 1 GB memory module (one-processor system) or two 1 GB memory modules (two-processor systems) PowerEdge M605, M600 1 GB (two 512 MB memory modules) Maximum RAM PowerEdge M915 512 GB PowerEdge M910 512 GB PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M710HD 288 GB PowerEdge M710 288 GB (Eighteen 16 GB RDIMMs); 36 GB (Eighteen 2 GB UDIMMs) PowerEdge M610x, M610 192
Drives (continued) PowerEdge M710 Up to four 2.5-inch SAS hard drives support through value RAID or performance RAID storage card. PowerEdge M600, M610x, M610 One 2.5-inch SATA hard drive support through nonRAID, value RAID, or performance RAID storage card. or Two 2.5-inch SATA hard drives support through value RAID or performance RAID storage card. or One solid-state disk (SSD) hard drive support through non-RAID storage card.
Connectors (continued) Internal Internal Secure Digital One optional flash memory card slot (SD) module (PowerEdge with the internal SD module. M915, M910, M905, M805, M710HD, M710, M610x, M610) Internal Secure Digital (SD) vFlash module (PowerEdge M915, M910, M710HD, M710, M610x, M610) One optional vFlash memory card slot for use with the iDRAC Enterprise support. USB key (PowerEdge M915, One internal USB key connector.
Mezzanine Cards (continued) PowerEdge M610x, M610 Up to two PCIe Gen 2 x8 mezzanine card slots, supporting dual-port Gb Ethernet, 10 Gb Ethernet, FC8 or FC4 (M610 only) Fibre Channel, or 4x DDR Infiniband mezzanine cards. PowerEdge M605, M600 Up to two PCIe x8 mezzanine card slots, supporting dual-port Gb Ethernet, 10 Gb Ethernet, FC8 or FC4 Fibre Channel, or 4x DDR Infiniband mezzanine cards.
Physical (continued) PowerEdge M910 Height 38.5 cm (15.2 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 13.1 kg (29 lb) PowerEdge M905, M805, M710, M610x Height 38.5 cm (15.2 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 11.1 kg (24.5 lb) PowerEdge M710HD Height 18.9 cm (7.4 in) Width 5 cm (2 in) Depth 48.6 cm (19.2 in) Weight (maximum configuration) 7.4 kg (16.3 lb) PowerEdge M605, M600 Height 18.9 cm (7.
System Enclosure Specifications Physical Height 44.0 cm (17.3 in) Width 44.7 cm (17.6 in) Depth 75.5 cm (29.7 in) Weight (maximum configuration) 178.3 kg (392.2 lb) Weight (empty) 44.6 kg (98.1 lb) Power Supply Module AC/DC power supply (per power supply) Wattage 2360 W and 2700 W Connector IEC C20 Heat dissipation 1205 BTU/hr.
Chassis Management Controller Module Externally accessible connectors Remote management Two dedicated 10/100/1000 Mb RJ-45 (for integrated Ethernet remote access controller). Gb port connects to the external management network. STK port allows CMCs in adjacent enclosures to be daisy chained. Serial 9-pin, DTE, 16550-compatible Video 15-pin VGA Battery CR 2032 3.0-V lithium ion coin cell Enclosure Control Panel Externally accessible connectors USB Two 4-pin, USB 2.
Environmental (continued) Relative humidity Operating 20% to 80% (noncondensing) at a maximum wet bulb temperature of 29 °C (84.2 °F) Storage 5% to 95% (noncondensing) at a maximum wet bulb temperature of 38 °C (100.4 °F) Maximum vibration Operating 0.26 Grms at 10 Hz–350 Hz for 15 min Storage 1.
22 Getting Started With Your System
Dell PowerEdge M1000e, M915, M910, M905, M805, M710HD, M710, M610x, M610, M605, et M600 Guide de mise en route Modèle BMX01, série HHB, série FHB
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque d'endommagement du matériel ou de perte de données en cas de non-respect des instructions. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessure corporelle ou de mort.
Installation et configuration AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous, lisez les consignes de sécurité fournies avec le système. Cette section décrit les étapes à exécuter lors de la configuration initiale du système. Déballage du système Sortez le système de son emballage et identifiez chaque élément.
Installation des lames Insérez les modules dans le boîtier en commençant par le haut et en procédant de gauche à droite. Lorsqu'une lame est correctement installée, la poignée revient en position fermée. Connexion des modules CMC et KVM Connectez le câble série et le ou les câbles réseau du système de gestion au module CMC. Si un second module CMC en option est installé, connectezle également. Connectez le clavier, la souris et l'écran au module iKVM en option.
Branchement du système sur le secteur Branchez les câbles d'alimentation du système aux blocs d'alimentation de celui-ci. PRÉCAUTION : Pour éviter que les câbles d'alimentation ne soient débranchés accidentellement, utilisez le clip en plastique situé sur chaque bloc d'alimentation pour y fixer le câble. Utilisez également la bande Velcro permettant de maintenir le câble sur la barre de retenue. Branchez l'autre extrémité des câbles d'alimentation dans une unité de distribution d'alimentation.
Mise sous tension du système Appuyez sur le bouton d'alimentation du boîtier. Le voyant d'alimentation doit s'allumer. REMARQUE : Une fois le système connecté aux blocs d'alimentation, un court laps de temps peut s'écouler avant que vous ne puissiez le mettre sous tension. Mise sous tension des lames Mettez chaque lame sous tension en appuyant sur son bouton d'alimentation ou en utilisant le logiciel de gestion des systèmes.
Finalisation de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez la documentation connexe fournie avec le système. Pour une première installation du système d'exploitation, consultez la documentation relative à l'installation et à la configuration de votre système d'exploitation. Veillez à installer le système d'exploitation avant tout élément matériel ou logiciel acheté séparément.
Système d'exploitation M915 M910 Microsoft Windows Server 2008, éditions Standard et Enterprise (x86) avec SP2 Microsoft Windows Server 2008, éditions Standard, Enterprise et Datacenter (x64) Microsoft Windows Web Server édition 2008 (x64) M905 M805 M710 M710HD M610 M610x Microsoft Windows Web Server édition 2008 (x64) avec SP2 Microsoft Windows Server 2008 R2, éditions Standard, Enterprise et Datacenter (x64) Microsoft Windows Ser
Système d'exploitation M915 M910 Microsoft Windows Server 2003 R2, éditions Standard et Enterprise (x64) M905 M805 M710 Microsoft Windows Server 2003 R2, édition Datacenter (x64) Microsoft Windows Server 2003 R2, éditions Standard, Enterprise et Datacenter (x64) avec SP2 M710HD M610 M610x M605 Red Hat Enterprise Linux AS, ES et WS (version 4.0), mise à jour 5 (x86) Red Hat Enterprise Linux AS, ES et WS (version 4.
Système d'exploitation M915 M910 Red Hat Enterprise Linux (version 5.0) (x86_64) M905 M805 M710 M710HD Red Hat Enterprise Linux (version 5.2) (x86) M610 Red Hat Enterprise Linux (version 5.5) (x86) Red Hat Enterprise Linux (version 5.5) (x86_64) Red Hat Enterprise Linux (version 6.
Système d'exploitation M915 M910 M905 M805 M710 M710HD M610 M610x VMware ESX version 4.0, mise à jour 1 VMware ESXi version 4.0, mise à jour 1 VMware ESX version 4.0, mise à jour 2 VMware ESXi version 4.0, mise à jour 2 VMware ESX version 4.1, mise à jour 1 VMware ESXi version 4.
• La documentation relative aux applications de gestion des systèmes Dell fournit des informations sur l'installation et l'utilisation du logiciel de gestion des systèmes. REMARQUE : Vérifiez toujours si des mises à jour sont disponibles sur le site support.dell.com/manuals et lisez-les en premier, car elles remplacent souvent les informations que contiennent les autres documents.
Mémoire Architecture PowerEdge M915 DIMM enregistrées (RDIMM) VL, de type DDR3 à simple, double ou quadruple rangée cadencées à 1333 MHz PowerEdge M910 Barrettes de mémoire DDR3, cadencées à 1066 MHz PowerEdge M905, M805, M605 Barrettes de mémoire DDR2, cadencées à 677 MHz PowerEdge M710HD Barrettes de mémoire DDR3 et DDR3L à simple, double et quadruple rangée, cadencées à 1066 et 1333 MHz PowerEdge M710 M610x, M610, DIMM enregistrées (RDIMM) ou DIMM sans tampon (UDIMM), de type DDR3 à simple ou do
Mémoire (suite) PowerEdge M710HD 1 Go, 2 Go, 4 Go, 8 Go et 16 Go RDIMM et DIMM LV PowerEdge M710, M610x, M610 RDIMM et DIMM LV de 2 Go, 4 Go, 8 Go et 16 Go ; UDIMM de 1 Go et 2 Go PowerEdge M605, M600 512 Mo, 1 Go, 2 Go, 4 Go et 8 Go RAM minimale PowerEdge M915 8 Go PowerEdge M910 4 Go PowerEdge M905 8 Go (huit barrettes de mémoire de 1 Go) PowerEdge M805 4 Go (quatre barrettes de mémoire de 1 Go) PowerEdge M710D 4 Go PowerEdge M710, M610x, M610 Une barrette de mémoire de 1 Go (systèmes à p
Lecteurs Disques Durs PowerEdge M915, M910 Prise en charge d'un ou de deux disques durs SAS 2,5 pouces via un adaptateur de stockage RAID de valeur ou haute performance. ou Prise en charge d'un ou de deux disques durs SSD 2,5 pouces via un adaptateur de stockage RAID de valeur ou haute performance. PowerEdge M905, M805 Prise en charge d'un ou de deux disques durs SAS 2,5 pouces via un adaptateur de stockage RAID de valeur ou haute performance.
Lecteurs (suite) PowerEdge M605 Prise en charge d'un ou de deux disques durs SATA via un adaptateur de stockage RAID de valeur ou haute performance. ou Prise en charge d'un ou de deux disques durs SSD via un adaptateur de stockage non-RAID. ou Prise en charge d'un ou de deux disques durs SAS via un adaptateur de stockage RAID de valeur ou haute performance. REMARQUE : Dans tous les systèmes modulaires, il n'est pas possible de combiner des disques durs SAS et SATA au sein d'une même lame.
Connecteurs (suite) Interne Module Secure Digital Un logement pour carte mémoire flash, en option, (SD) interne (PowerEdge avec le module interne SD. M915, M910, M905, M805, M710HD, M710, M610x, M610) Module Secure Digital (SD) VFlash interne (PowerEdge M915, M910, M710HD, M710, M610x, M610) Un logement pour carte mémoire VFlash, en option, pour une utilisation avec iDRAC Enterprise. Clé USB (PowerEdge M915, M910, M710HD, M710, M610x, M610) Un connecteur interne pour clé USB.
Cartes mezzanine (suite) PowerEdge M710 Jusqu'à quatre logements de carte mezzanine PCIe 2ème génération (trois emplacements x8 et un emplacement x4), prenant en charge des cartes mezzanine à double port Ethernet Gigabit, Ethernet 10 Gigabits, Fibre Channel FC8 ou FC4 ou Infiniband DDR 4x.
Caractéristiques physiques PowerEdge M915 Hauteur 38.5 cm (15.2 pouces) Largeur 5 cm (2 pouces) Profondeur 48,6 cm (19,2 pouces) Poids (configuration maximale) 12,7 kg (28 livres) PowerEdge M910 Hauteur 38.5 cm (15.2 pouces) Largeur 5 cm (2 pouces) Profondeur 48,6 cm (19,2 pouces) Poids (configuration maximale) 13,1 kg (29 livres) PowerEdge M905, M805, M710, M610x Hauteur 38.5 cm (15.
Pile Batterie de sauvegarde NVRAM Pile bouton au lithium CR 2032 (3 V) Spécifications du boîtier Caractéristiques physiques Hauteur 44 cm (17,3 pouces) Largeur 44,7 cm (17,6 pouces) Profondeur 75,5 cm (29,7 pouces) Poids (configuration maximale) 178,3 kg (392,2 livres) Poids (vide) 44,6 kg (98,1 livres) Bloc d'alimentation Bloc d'alimentation en CA/CC (selon la tension en vigueur) Puissance 2360 W et 2700 W Connecteur IEC C20 Dissipation thermique 1205 BTU/h.
Module CMC (Contrôleur de gestion de châssis) Connecteurs accessibles de l'extérieur Gestion à distance Deux connecteurs RJ-45 10/100/1000 Mo dédiés (pour le contrôleur d'accès à distance Ethernet intégré). Le port Gb est utilisé pour la connexion au réseau de gestion externe. Le port STK permet de relier en série des contrôleurs CMC installés dans des boîtiers adjacents.
Conditions environnementales (suite) Humidité relative En fonctionnement 20% à 80% (sans condensation) à une température de condensation maximale de 29 °C (84,2°F) Stockage 5% à 95% (sans condensation) à une température de condensation maximale de 38°C (100,4°F) Tolérance maximale aux vibrations En fonctionnement 0,26 Grms avec un balayage de 10 à 350 Hz pendant 15 mn Stockage 1,54 Grms avec un balayage de 10 à 250 Hz pendant 15 mn Choc maximal En fonctionnement Une impulsion de choc de 41 G pendan
Dell PowerEdge M1000e, M915, M910, M905, M805, M710HD, M710, M610x, M610, M605 e M600 Primeiros passos com o sistema Modelo BMX01, série HHB, série FHB
Notas, Avisos e Advertências NOTA: Uma NOTA fornece informações importantes para ajudar você a usar melhor o computador. AVISO: um AVISO indica um potencial de danos ao hardware ou a perda de dados se as instruções não forem seguidas. ADVERTÊNCIA: uma ADVERTÊNCIA indica um potencial de danos à propriedade, risco de lesões corporais ou mesmo de risco de vida. ____________________ As informações contidas nesta publicação estão sujeitas a alterações sem aviso prévio. © 2010 Dell Inc.
Instalação e configuração ADVERTÊNCIA: Antes de executar o procedimento abaixo, siga as instruções de segurança fornecidas com o sistema. Esta seção descreve as etapas necessárias para a configuração do sistema pela primeira vez. Remover o sistema da embalagem Remova o sistema da embalagem e identifique cada item. Como instalar os trilhos e o sistema no rack Monte os trilhos e instale o sistema no rack seguindo as instruções de segurança e as instruções de instalação do rack fornecidas com o sistema.
Como instalar as lâminas Deslize os módulos da caixa da esquerda para a direita, começando da parte superior. Quando a lâmina estiver instalada com segurança, a alça retorna para a posição fechada. Como conectar os módulos CMC e KVM Conecte os cabos serial e de rede do sistema de gerenciamento ao módulo CMC. Se um segundo módulo CMC opcional estiver instalado, conecte-o também. Conecte o teclado, o mouse e o monitor ao módulo iKVM opcional.
Como conectar o sistema à energia Conecte os cabos de alimentação do sistema às fontes de alimentação. AVISO: Para evitar que os cabos de alimentação se desconectem acidentalmente, use o clipe plástico de cada fonte de alimentação para prender o cabo à fonte e a tira de velcro para prender o cabo à barra de alívio de tensão. Conecte a outra extremidade do cabo de alimentação a unidade de distribuição de energia (PDU).
Como ligar o sistema Pressione o botão liga/desliga da caixa. A luz indicadora de energia deverá se acender. NOTA: Assim que você tiver conectado o sistema às fontes de alimentação, poderá haver uma demora mínima até que você possa ligar o sistema. Como ligar as lâminas Pressione o botão liga/desliga de cada lâmina ou ligue as lâminas através do software de gerenciamento de sistemas.
Concluir a configuração do sistema operacional Se você tiver adquirido um sistema operacional pré-instalado, consulte a documentação do sistema operacional fornecida. Para instalar um sistema operacional pela primeira vez, consulte a documentação de instalação e configuração do sistema operacional. Certifique-se de que o sistema operacional esteja instalado antes de instalar qualquer hardware ou software que não tenha sido adquirido com o sistema.
Sistema operacional M910 M905 M805 M710 Microsoft Windows Server 2008, edições Standard, Enterprise e Datacenter (x64) M915 Microsoft Windows edição Web Server 2008 (x64) M710HD M610 M610x Microsoft Windows edição Web Server 2008 (x64) com SP2 Microsoft Windows Server 2008 R2, edições Standard, Enterprise e Datacenter (x64) Microsoft Windows Server 2003, edições Standard e Enterprise Microsoft Windows Server 2003, edição Web Micros
Sistema operacional M915 M910 Microsoft Windows Server 2003 R2, edições Standard e Enterprise (x64) M905 M805 M710 Microsoft Windows Server 2003 R2, edição Datacenter (x64) Microsoft Windows Server 2003 R2, edições Standard, Enterprise e Datacenter (x64) com SP2 M710HD M610 M610x M605 Red Hat Enterprise Linux AS, ES e WS (versão 4.0) Atualização 5 (x86) Red Hat Enterprise Linux AS, ES e WS (versão 4.
Sistema operacional M905 M805 Red Hat Enterprise Linux(versão 5) (x86) M915 M910 Red Hat Enterprise Linux (versão 5.0) (x86_64) Red Hat Enterprise Linux (versão 5.2) (x86) M710 M710HD M610 Red Hat Enterprise Linux (versão 5.5) (x86) Red Hat Enterprise Linux (versão 5.5) (x86_64) Red Hat Enterprise Linux (versão 6.
Sistema operacional M915 M910 M905 M805 M710 M710HD M610 M610x VMware ESX versão 4.0, atualização 1 VMware ESXi, versão 4.0, atualização 1 VMware ESX versão 4.0, atualização 2 VMware ESXi, versão 4.0, atualização 2 VMware ESX versão 4.1, atualização 1 VMware ESXi, versão 4.1, atualização 1 M605 — compatível NOTA: Para obter as informações mais recentes sobre os sistemas operacionais compatíveis com todos os sistemas PowerEdge, consulte o site dell.
• A documentação do aplicativo de gerenciamento de sistemas Dell fornece informações sobre como instalar e usar o software de gerenciamento de sistemas. NOTA: Sempre verifique se há atualizações disponíveis no site support.dell.com/manuals (em inglês) e leia primeiro as atualizações, pois estas geralmente substituem informações contidas em outros documentos.
Memória Arquitetura PowerEdge M915 LV DIMMs (RDIMMs) registrados, com single-rank, dual-rank ou quad-rank de 1333 MHz PowerEdge M910 Módulos de memória DDR3, ajustados para a operação de 1066 MHz PowerEdge M905, M805, M605 Módulos de memória DDR2, ajustados para a operação de 677 MHz PowerEdge M710HD Módulos de memória DDR3 e DDR3L com singlerank, dual-rank e quad-rank, ajustados para 1066 e 1333-MHz PowerEdge M710, M610x, M610, DIMMs (UDIMMs) sem buffer ou DIMMs (RDIMMs) registrados, com single-ra
Memória (continuação) Capacidades dos módulos de memória PowerEdge M915 LV DIMMs de 1 GB, 2 GB, 4 GB, 8 GB e 16 GB PowerEdge M910 RDIMMs de 1 GB, 2 GB, 4 GB, 8 GB ou 16 GB PowerEdge M905, M805, 1 GB, 2 GB, 4 GB ou 8 GB PowerEdge M710HD 1 GB, 2 GB, 4 GB, 8 GB ou 16 GB RDIMMs e LV DIMMs PowerEdge M710, M610x, M610 2 GB, 4 GB, 8 GB, 16 GB RDIMMs e LV DIMMs; UDIMMs de 1 GB ou 2 GB PowerEdge M605, M600 512 MB, 1 GB, 2 GB, 4 GB ou 8 GB Mínimo de RAM PowerEdge M915 8 GB PowerEdge M910 4 GB PowerEdg
Memória (continuação) PowerEdge M610x, M610 192 GB (doze RDIMMs de 16 GB); 24 GB (doze UDIMMs de 2 GB); PowerEdge M605, M600 64 GB Unidades Discos rígidos PowerEdge M915, M910 Suporte para até duas unidades de disco rígido SAS de 2,5 polegadas via cartão de armazenamento RAID de desempenho ou RAID de valor. ou Suporte para até duas unidades de disco rígido SSD de 2,5 polegadas via cartão de armazenamento RAID de desempenho ou RAID de valor.
Unidades (continuação) PowerEdge M600, M610x, M610 Suporte para uma unidade de disco rígido SATA de 2,5 polegadas via cartão de armazenamento RAID de desempenho, RAID de valor ou não-RAID. ou Suporte para duas unidades de disco rígido SATA de 2,5 polegadas via cartão de armazenamento RAID de desempenho ou RAID de valor. ou Suporte para uma unidade de disco rígido de SSD via cartão de armazenamento não-RAID.
Conectores (continuação) PowerEdge M710HD, M610x, M610, M605, M600 Dois de 4 pinos, compatível com USB 2.0 Internos Módulo SD (Secure Digital) interno (PowerEdge M915, M910, M905, M805, M710HD, M710, M610x, M610) Um slot de cartão de memória flash opcional com o módulo SD interno. Módulo vFlash SD (Secure Um slot de placa de memória VFlash opcional para uso com o suporte iDRAC para empresas.
Placas para mezanino (continuação) PowerEdge M710 Até quatro slots de placa PCIe Gen 2 (três trilhas de x8 e uma trilha de x4 de largura), com suporte a placas Gb Ethernet de dois portas, 10 Gb Ethernet, FC8 ou FC4 Fibre Channel ou 4x DDR Infiniband para mezanino. PowerEdge M610x, M610 Até dois slots de placa PCIe Gen 2 x8 para mezanino, com suporte a placas Gb Ethernet de duas portas, 10 Gb Ethernet, FC8 ou FC4 (somente para o M610) Fibre Channel ou 4x DDR Infiniband para mezanino.
Características físicas PowerEdge M915 Altura 38,5 cm (15,2 polegadas) Largura 5 cm (2 polegadas) Profundidade 48,6 cm (19,2 polegadas) Peso (configuração máxima) 12,7 kg (28 libras) PowerEdge M910 Altura 38,5 cm (15,2 polegadas) Largura 5 cm (2 polegadas) Profundidade 48,6 cm (19,2 polegadas) Peso (configuração máxima) 13,1 kg (29 libras) PowerEdge M905, M805, M710, M610x Altura 38,5 cm (15,2 polegadas) Largura 5 cm (2 polegadas) Profundidade 48,6 cm (19,2 polegadas) Peso (configuraçã
Bateria Bateria de backup NVRAM bateria de célula tipo moeda de lítio CR 2032 de 3,0 V Especificações da caixa do sistema Características físicas Altura 44,0 cm (17,3 polegadas) Largura 44,7 cm Profundidade 75,5 cm (29,7 polegadas) Peso (configuração máxima) 178,3 kg (392,2 libras) Peso (vazio) 44,6 kg (98,1 libras) Módulo da fonte de alimentação Fonte de alimentação CA/CC (por fonte de alimentação) Potência 2.360 W e 2.700 W Conector IEC C20 Dissipação de calor 1205 BTU/h.
Módulo controlador de gerenciamento do chassi Conectores acessíveis externamente Gerenciamento remoto Duas portas RJ-45 10/100/1000 Mb (para controlador de acesso remoto Ethernet integrado). A porta Gb conecta-se com a rede de gerenciamento externa. A porta STK permite que os CMCs em caixas adjacentes sejam conectados em margarida.
Requisitos ambientais (continuação) Umidade relativa De operação 20% a 80% (sem condensação) em uma temperatura máxima do bulbo úmido de 29° C (84,2° F) De armazenamento 5% a 95% (sem condensação) em uma temperatura máxima do bulbo úmido de 38° C (100,4° F) Vibração máxima De operação 0,26 g RMS a 10–350 Hz por 15 minutos De armazenamento 1,54 g RMS a 10–250 Hz por 15 minutos Choque máximo De operação Um pulso de choque no eixo z positivo (um pulso de cada lado do sistema) de 41 G por até 2 ms De
Dell PowerEdge M1000e, M915, M910, M905, M805, M710HD, M710, M610x, M610, M605 y M600 Procedimientos iniciales con el sistema Modelo BMX01, serie HHB, serie FHB
Notas, precauciones y avisos NOTA: Una NOTA proporciona información importante que le ayudará a utilizar mejor el equipo. PRECAUCIÓN: Un mensaje de PRECAUCIÓN indica la posibilidad de que se produzcan daños en el hardware o haya pérdida de datos si no se siguen las instrucciones. AVISO: Un AVISO indica la posibilidad de que se produzcan daños materiales, lesiones personales e, incluso, riesgo de muerte. ____________________ La información contenida en esta publicación podrá modificarse sin previo aviso.
Instalación y configuración AVISO: Antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. En esta sección, se describen los pasos necesarios para configurar el sistema por primera vez. Desembalaje del sistema Desembale el sistema e identifique cada elemento.
Instalación de los módulos de alta densidad Empezando por la parte superior, inserte los módulos en el alojamiento de izquierda a derecha. Una vez que el módulo de alta densidad esté bien instalado, el asa volverá a la posición de cierre. Conexión de los módulos CMC y KVM Conecte el cable serie y los cables de red del sistema de administración al módulo CMC. Si va a instalar un segundo módulo CMC opcional, conéctelo también. Conecte el teclado, el ratón y el monitor al módulo iKVM opcional.
Conexión del sistema a la alimentación Conecte los cables de alimentación del sistema a las fuentes de alimentación. PRECAUCIÓN: Para evitar que los cables de alimentación se desconecten accidentalmente, utilice el gancho de plástico de cada fuente de alimentación para fijar el cable a la fuente de alimentación, y utilice la correa de velcro para fijar el cable a la barra liberadora de tensión. Enchufe el otro extremo de los cables de alimentación en la unidad de distribución de alimentación (PDU).
Encendido del sistema Pulse el botón de encendido del alojamiento. El indicador de alimentación debería encenderse. NOTA: Después de conectar el sistema a las fuentes de alimentación, puede producirse una pequeña demora antes de poder encender el sistema. Encendido de los módulos de alta densidad Pulse el botón de encendido de cada módulo de alta densidad o encienda los módulos mediante el software de administración de sistemas.
Instalación del sistema operativo Si ha adquirido un sistema operativo preinstalado, consulte la documentación del sistema operativo que se suministra con el sistema. Para instalar un sistema operativo por primera vez, consulte la documentación de instalación y configuración del sistema operativo. Asegúrese de que el sistema operativo está instalado antes de instalar hardware o software no adquirido con el sistema. Sistemas operativos compatibles Sistema operativo M915 M910 Citrix XenServer 5.
Sistema operativo M915 M910 Microsoft Windows Server 2008, ediciones Standard y Enterprise (x86) con SP2 Microsoft Windows Server 2008, ediciones Standard, Enterprise y Datacenter (x64) Microsoft Windows Web Server 2008 edición (x64) M905 M805 M710 M710HD M610 M610x Microsoft Windows Web Server 2008 edición (x64) con SP2 Microsoft Windows Server 2008 R2, ediciones Standard, Enterprise y Datacenter (x64) Microsoft Windows Server 200
Sistema operativo M915 M910 M905 M805 M710 M710HD M610 M610x Microsoft Windows Server 2003, ediciones Standard y Enterprise (x64) Microsoft Windows Server 2003 R2, ediciones Standard y Enterprise (x64) Microsoft Windows Server 2003 R2, edición Datacenter (x64) Microsoft Windows Server 2003 R2, ediciones Standard, Enterprise y Datacenter (x64) con SP2 M605 Red Hat Enterprise Linux AS, ES y WS (versión 4.
Sistema operativo M915 M910 M905 M805 M710 Red Hat Enterprise Linux AS y ES (versión 4.8) (x86_64) M710HD M610 Red Hat Enterprise Linux (versión 5.0) (x86) Red Hat Enterprise Linux (versión 5.0) x86_64 Red Hat Enterprise Linux (versión 5.2) (x86) Red Hat Enterprise Linux (versión 5.5) (x86) Red Hat Enterprise Linux (versión 5.5) (x86_64) Red Hat Enterprise Linux (versión 6.
Sistema operativo M915 M910 M905 M805 M710 M710HD M610 M610x VMware ESX versión 4.0 actualización 1 VMware ESXi versión 4.0 actualización 1 VMware ESX versión 4.0 actualización 2 VMware ESXi versión 4.0 actualización 2 VMware ESX versión 4.1 actualización 1 VMware ESXi versión 4.1 actualización 1 M605 : compatible NOTA: Para obtener la información más reciente sobre los sistemas operativos compatibles para todos los sistemas PowerEdge,visite dell.
Otra información útil AVISO: Antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. • La Guía de configuración proporciona información sobre cómo configurar el alojamiento del sistema y los módulos de alta densidad. • En las Instrucciones de instalación del rack incluidas con el rack, se describe cómo instalar el sistema en un rack.
Información de la NOM (sólo para México) La información que se proporciona a continuación aparece en el dispositivo que se describe en este documento, en cumplimiento con los requisitos de la Norma Oficial Mexicana (NOM): Importador: Número de modelo: Voltaje de alimentación: Frecuencia: Consumo eléctrico: BMX01 100-240 V CA 50/60 Hz 16 (x6) A Importador: Número de modelo: Voltaje de alimentación: Consumo eléctrico: FHB 12 V CC 75 A Importador: Número de modelo: Voltaje de alimentación: Consumo eléct
Especificaciones técnicas Especificaciones del módulo de alta densidad Procesador Tipo de procesador PowerEdge M915 Dos o cuatro procesadores AMD Opteron serie 6000 (procesadores de ocho o doce núcleos) PowerEdge M910 Dos o cuatro procesadores Intel Xeon serie 7000 (procesadores de hasta ocho núcleos) PowerEdge M905 Cuatro procesadores AMD Opteron serie 8000 de dos o cuatro núcleos PowerEdge M805 Dos procesadores AMD Opteron serie 2000 de dos o cuatro núcleos PowerEdge M710HD, M710, M610x y M610 Un
body.
Memoria (continuación) RAM máxima PowerEdge M915 512 GB PowerEdge M910 512 GB PowerEdge M905 192 GB PowerEdge M805 128 GB PowerEdge M710HD 288 GB PowerEdge M710 288 GB (18 módulos RDIMM de 16 GB); 36 GB (18 módulos UDIMM de 2 GB) PowerEdge M610x y M610 192 GB (12 módulos RDIMM de 16 GB); 24 GB (12 módulos UDIMM de 2 GB) PowerEdge M605 y M600 64 GB Unidades Unidades de disco duro 82 PowerEdge M915 y M910 Se admiten hasta dos unidades de disco duro SAS de 2,5 pulgadas mediante tarjeta de al
Unidades (continuación) PowerEdge M600, M610x y M610 Se admite una unidad de disco duro SATA de 2,5 pulgadas mediante tarjeta de almacenamiento sin RAID, RAID básica o RAID de alto rendimiento. O bien Se admiten dos unidades de disco duro SATA de 2,5 pulgadas mediante tarjeta de almacenamiento RAID básica o RAID de alto rendimiento. O bien Se admite una unidad de disco duro sólido (SSD) mediante tarjeta de almacenamiento sin RAID.
Conectores (continuación) Internos Módulo Secure Digital Una ranura para tarjeta de memoria flash (SD) interno (PowerEdge opcional con el módulo SD interno M915, M910, M905, M805, M710HD, M710, M610x y M610) Módulo Secure Digital (SD) vFlash interno (PowerEdge M915, M910, M710HD, M710, M610x y M610) Una ranura para tarjeta de memoria vFlash opcional para utilizarla con el soporte de iDRAC Enterprise Memoria USB (PowerEdge Un conector para memoria USB interno M915, M910, M710HD, M710, M610x y M610) Solució
Tarjetas intermedias (continuación) PowerEdge M610x y M610 Hasta dos ranuras para tarjeta intermedia PCIe Gen 2 x8, que admiten tarjetas intermedias Ethernet Gb, 10 Gb Ethernet, Fibre Channel FC8 o FC4 (sólo M610), o Infiniband DDR 4x de dos puertos. PowerEdge M605 y M600 Hasta dos ranuras para tarjeta intermedia PCIe x8, que admiten tarjetas intermedias Ethernet Gb, 10 Gb Ethernet, Fibre Channel FC8 o FC4, o Infiniband DDR 4x de dos puertos.
Características físicas (continuación) PowerEdge M910 Altura 38,5 cm (15,2 pulgadas) Ancho 5 cm (2 pulgadas) Largo 48,6 cm (19,2 pulgadas) Peso (configuración máxima) 13,1 kg (29 libras) PowerEdge M905, M805, M710 y M610x Altura 38,5 cm (15,2 pulgadas) Ancho 5 cm (2 pulgadas) Largo 48,6 cm (19,2 pulgadas) Peso (configuración máxima) 11,1 kg (24,5 libras) PowerEdge M710HD Altura 18,9 cm (7,4 pulgadas) Ancho 5 cm (2 pulgadas) Largo 48,6 cm (19,2 pulgadas) Peso (configuración máxima) 7,4
Especificaciones del alojamiento del sistema Características físicas Altura 44,0 cm (17,3 pulgadas) Ancho 44,7 cm (17,6 pulgadas) Largo 75,5 cm (29,7 pulgadas) Peso (configuración máxima) 178,3 kg (392,2 libras) Peso (vacío) 44,6 kg (98,1 libras) Módulo de fuente de alimentación Fuente de alimentación de CA/CC (por cada fuente de alimentación) Potencia 2 360 W y 2 700 W Conector IEC C20 Disipación de calor 1 205 BTU/h como máximo Corriente de conexión máxima En condiciones normales de línea y
Módulo de controladora de administración del chasis Conectores de acceso externo Administración remota Dos RJ-45 10/100/1000 Mb dedicados (para una controladora de acceso remoto Ethernet integrada). El puerto Gb se conecta a la red de administración externa. El puerto STK permite la conexión secuencial de módulos CMC de alojamientos adyacentes.
Especificaciones ambientales (continuación) Humedad relativa En funcionamiento De 20% a 80% (sin condensación) a una temperatura de humedad máxima de 29 °C (84,2 °F) Almacenamiento De 5% a 95% (sin condensación) a una temperatura de humedad máxima de 38 °C (100,4 °F) Vibración máxima En funcionamiento 0,26 Grms a 10–350 Hz durante 15 minutos Almacenamiento 1,54 Grms a 10–250 Hz durante 15 minutos Impacto máximo En funcionamiento Un choque en el sentido positivo del eje z (un choque en cada lado del
90 Procedimientos iniciales con el sistema