EN Series Power Distribution Unit & EZ Series Energy Meter Installation and Operation Manual For more information, go to www.enlogic.com.
www.enlogic.
EN Series User Manual Table of Contents PDU Safety Guidelines....................................................................................................... 4 Section 1: Introduction Enlogic Product Series . ...................................................................................................... 5 Product Components......................................................................................................... 5 Input Power Cord ...............................................
PDU Safety Guidelines This document is intended for installers, maintenance professionals, and qualified users of Enlogic power distribution units (PDUs). Keep this safety information for operation, installation, and maintenance of the PDU and accessory equipment. This product complies with the latest safety requirements for equipment and accessories for use in a rack mounting environment. Read and follow all safety information. Failure to do so may result in death or serious injury.
EN Series User Manual Section 1: Introduction This manual is intended to assist in the installation and setup the EN Series PDU. Refer to this manual to properly install and operate the EN Series PDU. It is recommended that the user follows the procedures as outlined in this manual to assist in proper installation and prevent damage to the PDU and associated equipment.
Connection Ports There are 6 ports on all standard EN Series models, as shown below. • USB: to connect the EN Series PDU to a USB flash drive to upload firmware or download log files.
EN Series User Manual The Critical Component 7
www.enlogic.
EN Series User Manual Menu, Reset, and Unit Status Button These are all on the front of the PDU underneath the OLED Display. The are as follows: 1: Reset Button 2: Unit Status LED 3: Menu Buttons 1 2 3 Unit Status LED LED State Description Solid Green Normal Operation Solid Red Alarm State Blinking Orange Disconnected from network Menu Buttons The Menu Buttons allow a user to navigate through the OLED display. They are: • Menu–Use this button as a “back” button to go to the previous menu screen.
Single-Phase Models } For single phase models, each circuit breaker is connected to like-colored outlets. For example, all white outlets are connected to the white circuit breaker, and all blue outlets are connected to the blue circuit breaker. } Three-Phase Models For 3-phase models, 3 colors are used to identify the 3 different input lines. • In standard 400V 3-phase (Wye) configurations, the color of each circuit breaker and outlet correspond to the appropriate input phase.
EN Series User Manual Section 2: Installation Before Installation 1. Prepare the installation site: make sure it is not exposed to extreme temperature or humidity. Make sure to allow space around the Enlogic PDU for cabling and outlet connections. Note: Enlogic PDUs are designed for maximum operating temperatures of 55–60°C (131–140°F). Refer to each model’s technical datasheet for specific information. 2. Check the Branch Circuit Rating in the Safety Information section of this manual. 3.
4. Turn the feed circuit breaker on. The OLED screen will display a status bar when the PDU operating system is loading. When complete, the Main Menu will display on the OLED screen. Switched PDUs in the EN2000 series or EN6000 series show a light corresponding to each outlet as it is powered up. Connecting the PDU to a Network The EN series PDU is DHCP compatible. If the network does not use a DHCP server, see the steps below for “Connecting with a Serial Connection”.
EN Series User Manual 5. Use the default initial login indicated below. Note that the username and password are both case sensitive: • Username: admin • Password: 12345678 6. The ENLOGIC> prompt appears after you have logged in. 7. To configure network settings, enter the appropriate net commands and press Enter. All commands are case sensitive. You can type ? to access the commands. • For the IPv4 DHCP configuration, configure this parameter.
Section 3: Enlogic Web User Interface (Web UI) The Enlogic Web UI is used to manage, control, configure, and administer Energy series PDUs and accessories. Supported Browsers The Enlogic Web UI is accessible from any of these browsers: • • • • Firefox Internet Explorer® 7 (IE7) or higher version Safari Chrome Logging In to the Enlogic Web UI Logging In 1. Open a supported web browser and enter the ip address of the EN Series PDU. For example, 10.2.11.24 2.
EN Series User Manual Action Menus The action menus allow an administrator to navigate through the Enlogic Web UI easily and efficiently to manage various tasks. • • • User Administration: allows user to change the account password, add/remove users, and edit user roles Device Configuration: allows user to edit/view device, network, and security settings. System Administration: allows user to access tools to maintain the device, such as the event and data logs, device information, and firmware maintenance.
Customized Permissions for user customized roles can be set as needed. Change Password 1. Go to User Administration>Change Password. 2. The Change User Password window opens. 3. Enter the old password and then new password twice to confirm. By default, passwords must be between 8 and 32 characters. To configure password requirements to suit your organization, refer to the “Security” section of this manual. Users Add: To add a user, go to User Administration>Users, 1.
EN Series User Manual Roles To change user roles, privileges, and settings, go to User Administration>Roles. To create a new role, 1. 2. 3. 4. 5. 6. Select New. In the Settings tab. enter the Role Name and Description. In the Privileges tab, select Edit. Select the privileges to add to that user role. Set parameters if necessary. Select OK. Select Save. To modify a custom user role, 1. Select the role. 2. Select the Edit button. 3. Edit the role name and privileges as needed. Select Save.
Telnet Enabling Telnet allows for a user to login to the CLI using a Telnet client (such as PuTTY) or change the TCP port for the Telnet service. FTP Only Admin users can access FTP settings. Network Configuration To modify Internet Protocol (IPv4 or IPv6*) and Settings, 1. Go to Device Configuration > Network Configuration. 2. Select the desired options on the IP Protocol Tab. 3.
EN Series User Manual The Critical Component 19
Appendix A: EN Series Bracket Mounting Info When mounting your EN Series PDU, refer to the table below for specific mounting requirements and to see if a separate bracket kit is required for proper mounting. 20 Manufacturer Models Separate Bracket Kit Required? APC Netshelter SX No Chatsworth Terraframe Yes Chatsworth Power Strip Lashing Bracket, part no.
EN Series User Manual The Critical Component 21
The Critical Component Enlogic Systems, LLC. Wildwood Missouri USA 63040 sales@amer.enlogic.com 22 Enlogic Systems Europe, Ltd. Worcester United Kingdom WR1 2PG sales@emea.enlogic.com www.enlogic.com www.enlogic.com Enlogic Systems Asia Pacific, Ltd. Tsim Sha Tsui Kowloon, Hong Kong sales@apac.enlogic.
