Dell EMC PowerEdge Sunucuları Sorun Giderme Kılavuzu
Notlar, dikkat edilecek noktalar ve uyarılar NOT: NOT, ürününüzü daha iyi kullanmanıza yardımcı olacak önemli bilgiler sağlar. DİKKAT: DİKKAT, donanımda olabilecek hasarları ya da veri kaybını belirtir ve bu sorunun nasıl önleneceğini anlatır. UYARI: UYARI, meydana gelebilecek olası maddi hasar, kişisel yaralanma veya ölüm tehlikesi anlamına gelir. © 2017 - 2019 Dell Inc. veya bağlı kuruluşları. Tüm hakları saklıdır. Dell, EMC ve diğer ticari markalar, Dell Inc.
İçindekiler 1 Giriş................................................................................................................................................................8 Hedef Kitle.......................................................................................................................................................................... 8 Önerilen araçlar...................................................................................................................................
Mikro SD kartına yönelik sorun giderme.........................................................................................................................51 Genişletme kartlarında sorun giderme............................................................................................................................51 İşlemcilere yönelik sorun giderme...................................................................................................................................
Dell'in 13. nesil PowerEdge sunucularındaki ESXi ana bilgisayarlarında PERCCLI aracını kullanarak RAID denetleyicisi günlüğünün dışa aktarılmış halini indirme ve yükleme...................................................................... 82 Yaşam Döngüsü Denetleyicisi kullanarak RAID'i yapılandırma............................................................................... 86 Sanal disk yeniden yapılandırma ve kapasite genişletme için RAID düzeylerini başlatma ve hedefleme..........
İşlemci TEMP hatası........................................................................................................................................................114 PowerEdge T130, R230, R330 ve T330 sunucuları, zamanlanmış sıcak başlatmalar sırasında Kritik Bir Hata bildirebilir........................................................................................................................................................................... 114 SSD algılanmadı...............................
Yardım alma................................................................................................................................................ 134 Dell EMC ile iletişime geçme..........................................................................................................................................134 Sürücüleri ve ürün yazılımını indirme.............................................................................................................................
1 Giriş Dell PowerEdge sunucu sorunlarının nasıl tespit edileceğini ve nasıl giderileceğini öğrenmek için bu kılavuzu kullanın. Özellikle, bu kılavuz: • Sunucu İşletim Sistemi, Sunucu Donanımı ve Sunucu Yönetim Yazılımı ile ilgili sorunlar için sorun giderme prosedürleri sağlar. • Tanılama göstergelerine genel bir bakış sağlar ve sorun giderme işlemini kolaylaştırmak için gösterge kodlarının nasıl kullanılacağını açıklar.
Dokümantasyon kaynakları Bu bölümde sisteminiz için dokümantasyon kaynakları hakkında bilgi verilmiştir. Belge kaynakları tablosunda listelenen belgeyi görüntülemek için: • Dell EMC destek sitesinden: a Tabloda yer alan Konum sütununda verilen belge bağlantısına tıklayın. b Gerekli ürüne ya da ürün sürümüne tıklayın. NOT: Ürün adını ve modelini bulmak için sisteminizin ön kısmına bakın. c • Product Support (Ürün Desteği) sayfasında, Manuals & documents (Kılavuzlar ve belgeler) sayfasına tıklayın.
Görev Belge Konum Sisteminizi yönetme Dell tarafından sunulan sistem yönetimi yazılımı hakkında daha fazla bilgi için, Dell OpenManage Sistem Yönetimi Genel Bakış Kılavuzu'na bakın. Dell.com/poweredgemanuals OpenManage kurulumu, kullanımı ve sorun giderme Dell.com/openmanagemanuals > OpenManage hakkında bilgi için bkz. Dell OpenManage Sunucu Server Administrator Yöneticisi Kullanıcı Kılavuzu.
2 Tanı göstergeleri Sistemdeki tanılama göstergeleri, çalışma ve hata durumunu gösterir. Durum LED'i göstergeleri Sistem ön panelindeki Durum LED'i göstergeleri sistem başlatması sırasında hata durumunu görüntüler. NOT: Sistem kapalıyken hiçbir Durum LED'i göstergesi yanmaz. Sistemi başlatmak için, çalışan bir güç kaynağına takın ve güç düğmesine basın. NOT: Durum LED'i göstergeleri her zaman kapalıdır ve yalnızca herhangi bir hata olduğunda sabit sarıya döner. Tablo 2.
Simge Açıklama Koşul Düzeltici eylem NOT: Desteklenen PCIe kartları hakkında daha fazla bilgi için bkz. Genişletme kartı takma yönergeleri bölümü. Sistem durumu ve sistem kimliği gösterge kodları Rakam 1. Sistem sağlığını izlemek ve sistem KIMLIĞI göstergeleri Tablo 3. Sistem durumu ve sistem kimliği gösterge kodları Sistem sağlığını izlemek ve sistem KIMLIĞI gösterge kodu Koşul Sabit mavi Sistemin açık, sağlıklı olduğunu ve sistem ID modunun etkin olmadığını gösterir.
Kablosuz gösterge kodu Koşul Düzeltici eylem düğmesine basarak iDRAC Quick Sync 2 özelliğini açın. Sabit beyaz iDRAC Quick Sync 2'nin iletişim kurmaya hazır olduğunu gösterir. Kapatmak için iDRAC Quick Sync 2 düğmesine basın. LED sönmezse, sistemi yeniden başlatın. Sorun devam ederse, Yardım Alma bölümüne bakın. Hızlı yanıp sönen beyaz Veri aktarımı faaliyetini gösterir. Gösterge sürekli olarak yanıp sönmeye devam ederse, bkz. Yardım Alma.
Rakam 3. NIC göstergeleri 1 Bağlantı LED göstergesi 2 Etkinlik LED göstergesi Tablo 6. NIC göstergeleri Durum Koşul Bağlantı ve faaliyet göstergeleri kapalı NIC ağa bağlı değil. Bağlantı göstergesi yeşil ve etkinlik göstergesi yeşil yanıp sönüyor NIC, maksimum bağlantı noktası hızında geçerli bir ağa bağlı ve veri gönderiliyor veya alınıyor.
Güç göstergesi kodları Koşul Yanmıyor Güç bağlı değil. Yanıp sönen yeşil PSU ürün yazılımı güncelleniyorken, PSU kolu yeşil yanıp söner. DİKKAT: Bellenim güncellenirken, güç kablosunun ya da PSU'nun bağlantısını kesmeyin. Bellenim güncellemesi kesilirse, PSU'lar işlev görmeyecektir. Yeşil yanıp söner ve kapanır Bir PSU'yu çalışırken ekleme sırasında, PSU kolu 4 Hz hızında beş kez yeşil yanıp söner ve kapanır.
Güç göstergesi kodları Koşul Yanmıyor Güç bağlı değil. Yanıp sönen yeşil Bir PSU çalışırken takıldığında, PSU göstergesi yeşil renkte yanıp söner. Bu durum verimlilik, özellik kümesi, sağlık durumu veya desteklenen voltaj açısından bir PSU uyuşmazlığı olduğunu belirtir. DİKKAT: PSU uyuşmazlığını düzeltirken, yalnızca yanıp sönen göstergeli PSU'yu değiştirin. Eşleşen bir çift yapmak için PSU'yu değiştirmek, hata durumuna ve sistemin beklenmedik şekilde kapanmasına neden olabilir.
Rakam 7. Sabit sürücü göstergeleri 1 Sabit sürücü etkinlik göstergesi 3 Sabit sürücü 2 Sabit sürücü durumu LED göstergesi NOT: Sabit sürücü Gelişmiş Ana Makine Denetleyicisi Arabirimi (AHCI) modundaysa durum LED göstergesi açılmaz. Tablo 10. Sabit sürücü gösterge kodları Sürücü durumu gösterge modeli Koşul Saniyede iki defa yeşil yanıp söner Sürücü tanımlama veya sökme işlemi için hazırlık. Kapalı Sürücü, takma ya da sökme işlemi için hazır.
uSATA SSD gösterge kodları Rakam 8. uSATA SSD göstergeleri 1 uSATA SSD etkinlik göstergesi 3 uSATA SSD 2 uSATA SSD durum göstergesi NOT: SSD, Gelişmiş Ana Makine Denetleyicisi Arabirimi (AHCI) modundaysa durum göstergesi (sağ tarafta) çalışmaz ve kapalı kalır. Tablo 11. Sürücü durumu gösterge kodları Sürücü durumu gösterge modeli Koşul Saniyede iki defa yeşil yanıp söner Sürücü tanımlama veya sökme işlemi için hazırlık. Kapalı Sürücü, takma ya da sökme işlemi için hazır.
Tablo 12. IDSDM gösterge kodları Kural IDSDM gösterge kodu Açıklama A Yeşil Kartın çevrimiçi olduğunu gösterir. B Yanıp sönen yeşil Yeniden kurmayı veya faaliyeti gösterir. C Hızlı yanıp sönen turuncu Kart uyumsuzluğunu veya kartın hata verdiğini gösterir. D Sarı renkli Kartın çevrimdışı olduğunu, hata verdiğini veya yazma korumalı olduğunu gösterir. E Yanmıyor Kartın eksik olduğunu veya yeniden başlatıldığını gösterir.
3 Tanılamayı çalıştırma Tanılamayı çalıştırmak, bir sistem sorununun nedenini belirlemenize yardımcı olur. Tanılama araçları, ek donanım veya veri kaybı riski olmaksızın sistem donanımlarınızı test eder.
PSA ve ePSA Tanılama hata kodları NOT: Sistem bileşenlerini izleyen sistem ürün yazılımı ve aracıları tarafından üretilen olay ve hata iletileri hakkında bilgi için qrl.dell.com adresindeki Hata Kodu Arama sayfasına bakın. Tablo 13. PSA/ePSA hata kodları Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar PSA NA CPU - özel durum oluştu. Testler sırasında sistem kartı ile ilgili olabilecek bir hata oluştu.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 4 PSA 1000-0122 ePSA 2000-0122 PSA Bellek - test başlatma arızası ePSA Bellek - bellek hataları ve aşırı hatalar algılandı Testler sırasında sistem kartı veya 1 sistem belleği ile ilgili olabilecek bir hata oluştu. Ancak, sistem 2 kendi kendini onardı. 3 4 PSA 1000-0123 ePSA 2000-0124 PSA NA Testler sırasında sistem kartı veya 1 sistem belleği ile ilgili olabilecek bir hata oluştu. Ancak, sistem 2 kendi kendini onardı.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar PSA NA Pil - pil yeterli güç sağlayamıyor Testler sırasında ana sistem kartı veya sistem pili ile ilgili olabilecek bir hata oluştu. 1 ePSA 2000-0133 2 3 4 PSA 2000-0141 ePSA 2000-0141 PSA 1000-0142 ePSA 2000-0142 Sabit Sürücü - hiçbir sürücü algılanmadı Sistem BIOS'unuz hiçbir Sabit Disk Sürücüsünün rapor edilmediğini bildiriyor.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 4 5 6 PSA 1000-0146 ePSA 2000-0146 Sabit Sürücü - kendi kendini sınama günlüğü önceki hataları içeriyor Sabit sürücünüzde bir arıza olduğu belirtildi. 1 2 3 4 PSA 1000-0147 ePSA 2000-0147 PSA Optik Sürücü - IDE durumu başarısız. CD veya DVD sürücünüzde bir arıza olduğu belirtildi.
Hata numarası (PSA ve ePSA) PSA NA Hata iletisi Sabit Sürücü - BIST --(s) ePSA 2000-0151 Açıklama Adımlar tekrar gerçekleştirin. Çalışan yedek bir sabit sürücü varsa, çalışan sabit sürücünün sistem tarafından algılanıp algılanmadığına bakın veya şüpheli sürücüyü çalışan bir sistemde deneyin. 4 Sabit sürücü, tanılamada yanlış bir durum gösteriyor. Sabit sürücünüz için bir ürün yazılımı güncellemesi olup olmadığını kontrol edin.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar PSA 1000-0212 Sistem kartı - CMOS, Konum = (x), Beklenen = (x), Bulunan = (x) Testler sırasında sistemin ana sistem kartı ile ilgili olabilecek bir hata oluştu.
Hata numarası (PSA ve ePSA) Hata iletisi ePSA 2000-0224 (UEFI BIOS ile kullanılmaz) PSA 1000-0231 ePSA 2000-0231 (UEFI BIOS ile kullanılmaz) PSA 2000-0232 ePSA 2000-0232 (UEFI BIOS ile kullanılmaz) PSA 2000-0233 ePSA 2000-0233 (UEFI BIOS ile kullanılmaz) PSA 1000-0234 ePSA 2000-0234 (UEFI BIOS ile kullanılmaz) Sistem kartı - Aralık zamanlayıcı modunda arıza Sistem kartı - RTC periyodik işaretler üretmedi PSA Sistem kartı - RTC 'saniye' sayısı güncellenmiyor ePSA RTC - 'saniye' sayısı güncellenmiyor
Hata numarası (PSA ve ePSA) PSA 1000-0241 Hata iletisi BIOS - A20 kapısı etkin değil ePSA 2000-0241 (UEFI BIOS ile kullanılmaz) PSA 1000-0242 ePSA 2000-0242 (UEFI BIOS ile kullanılmaz) PSA NA ePSA 2000-0243 PSA NA PSA Sistem kartı - IRQ için kesinti algılanmadı.
Hata numarası (PSA ve ePSA) PSA NA ePSA 2000-0251 PSA NA Hata iletisi Olay Günlüğü - günlük arızalı kayıtlar içeriyor. Açıklama Adımlar USB aygıtlarını farklı bir bağlantı noktasında test edin. Düzgün çalıştığını bildiğiniz bir USB aygıtı deneyin. 3 Arıza devam ederse Dell Teknik Desteği ile iletişime geçin Bu sadece sunuculardaki BIOS olaylarıyla ilgilidir. 1 En son BIOS sürümüne güncelleyin. PSA tanılamasını tekrar gerçekleştirin. 2 Sistem kartı - Veri hataları.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar PSA 1000-0322 PSA LCD Paneli - LCD çeviriciye erişim hatası LCD paneli - parlaklık değiştirilemedi. Windows ekran parlaklığını kısayol tuşlarını kullanarak ayarlamayı deneyin. BIOS'a önyükleme yapın ve parlaklığın Windows dışındaki noktada ayarlanabilme durumunu kontrol edin 1 ePSA 2000-0322 PSA NA ePSA 2000-0323 ePSA LCD paneli - parlaklık değiştirilemiyor LCD panel - Çevirici lambasının durumu algılanamıyor.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 3 4 PSA NA ePSA 2000-0328 LCD paneli - ortam ışığı sensöründeki farklılıklar tespit edilemiyor Düşük ışıkta LCD'yi otomatik olarak karartan Ortam ışığı sensörü tanılama sırasında yanıt vermedi. 1 2 3 4 PSA NA ePSA 2000-0331 Video denetleyicisi - video denetleyicisi algılanmadı Sistem grafik adaptörünü algılamıyor.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar PSA 1000-0334 Video - kullanıcı, desenlerin doğru gösterilmediğini bildirdi Renk testine Evet yerine Hayır cevabı verdiyseniz bu hatayı alabilirsiniz. Hem dikey hem de yatay renk çubuklarını bozulma, çizgi veya renk sorunları olmadan açıkça görebiliyorsanız tanılamayı yeniden çalıştırın ve çubuk normal görünüyorsa Evet’e tıklayın.
Hata numarası (PSA ve ePSA) Hata iletisi ePSA 2000-0414 Açıklama Adımlar bağlantısını tekrar yerleştirin ve kablo ile bağlantılarda hasar olup olmadığını kontrol edin. 2 3 4 5 PSA NA ePSA 2000-0415 Kablolar - Şu kabloları, bağlantı kablosunu, bağlantı veya sensörleri kontrol edin: [s] Normalde, hata oluşan kablo 1 (örneğin LCD LVDS CABLE) hata iletisinde gösterilir. Kablo 2 bağlantısını tekrar yerleştirin ve kablo ile bağlantılarda hasar olup olmadığını kontrol edin.
Hata numarası (PSA ve ePSA) PSA NA ePSA 2000-0621 Hata iletisi Ağ - Ağ [d] - Sürücü sürümü [x] güncel değil. "[s]" için [x] veya üzeri bir sürüm gerekli Açıklama Adımlar başarısız oldu) gibi hatalar oluşabilir. 4 Ağ (Ethernet) aygıtı Ürün Yazılımı 1 güncel olmayabilir. 2 3 PSA NA ePSA 2000-8001 BIOS - [x] yazılım kesintisi işlev[x] Anakart BIOS revizyonu güncel [x] için BIOS desteği yok olmayabilir. BIOS'u en güncel sürüme güncellediğinizde sorunun çözülmesi gerekir.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 3 PSA NA ePSA 2000-8007 BIOS - Günlükte Fan olayları var veya Zamanlayıcı [d] beklerken [d] gözlemledi Bu mesaj yalnızca bilgi amaçlıdır 1 fan etkinliklerinin kaydını sağlar. 2 3 PSA NA ePSA 2000-8008 Tanılama - A Bellek yetersiz! fMalloc() Başarısız! B. Nesne verileri için bellek ayrılamıyor. Test edilebilir bellek [s] yapılamıyor Sistem dengesiz olabilir ve yeniden başlatılması gerekiyor olabilir. 1 2 3 C.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 2 3 PSA NA ePSA 2000-800F BIOS - Geri yükle işlev hatası. Satıcı Firma: [s] Değişiklik: [d]. Anakart BIOS revizyonu güncel olmayabilir. 1 2 3 PSA NA Sistem Kartı ePSA 2000-8010 Yüksek Hassasiyetli olay zamanlayıcısı bulunamadı. 1 2 3 PSA NA ePSA 2000-8011 USB Aygıt Tanılama - Aygıttan geçersiz durum döndürüldü Ekli USB aygıtı, BIOS'a geçersiz bir durum döndürüyor.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 3 4 PSA NA ePSA 2000-8017 BIOS - Pil - BIOS'ta pil durumu desteği yok Bu isteğe bağlı özellik desteklenmiyor olabilir. 1 2 3 PSA NA ePSA 2000-8018 Tanılama - Önemli: Modül birden fazla test sonucu bildirdi! Sistem kararsız hale gelebilir. 1 2 3 PSA NA ePSA 2000-8019 Tanılama - NVRAM'de oturum açılamıyor Sistem kararsız hale gelebilir. 1 2 3 PSA NA ePSA 2000-8020 Tanılama - Düşük bellek. [d]k bayt boş! Sistem kararsız hale gelebilir.
Hata numarası (PSA ve ePSA) Hata iletisi Açıklama Adımlar 2 3 PSA NA ePSA 2000-8156 Teyp Sürücü - Teyp Sürücü [d] S/N [s], ortam yok, sürücü test edilemez Yazılabilir teyp sürücü ortamı takın. 1 2 3 PSA NA ePSA 2000-8157 Teyp Sürücü - Teyp Sürücü [d] S/N [s], sürücü desteklenen bir sürücü değil Teyp sürücü modeli bilinmiyor ve tanılama tarafından desteklenmiyor.
Hata numarası (PSA ve ePSA) PSA NA ePSA 2000-8415 Hata iletisi Kablolar - BIOS, test edilebilir kablo/atlama teli/konnektör/ sensör olmadığını bildiriyor Açıklama Tanılama aracında iç arıza mevcut, donanım arızası değil. Adımlar 3 Arıza devam ederse Dell Teknik Desteği ile iletişime geçin 1 En son BIOS sürümüne güncelleyin. PSA tanılamasını tekrar gerçekleştirin.
Rakam 9. Sistem sayfasını açma 2 System (Sistem) sayfasında, sol paneldeki Advanced system settings (Gelişmiş sistem ayarları) öğesine tıklayın. Rakam 10.
3 System Properties (Sistem Özellikleri) penceresinde, Startup and Recovery (Başlangıç ve Kurtarma) bölümünün altındaki Settings (Ayarlar) öğesine tıklayın. Rakam 11.
Rakam 12. Başlangıç ve Kurtarma penceresi 5 Bir BSOD oluştuğunda, mini döküm dosyalarını şu konuma giderek toplayın: C:\windows\minidump. 6 Windows Hata Ayıklayıcısı (WinDbg) aracını şu adresten indirip yükleyin: https://msdn.microsoft.com/en-us/windows/hardware/ hh852365.aspx. Adimlar 1 WinDbg'yi açın. 2 File (Dosya) → Symbol File Path (Sembol Dosya Yolu) öğesine tıklayın veya klavyede Ctrl + S tuşlarına basın. 3 Symbol Path (Sembol Yol) alanına SRV**http://msdl.microsoft.
c 11 IMAGE_NAME Daha fazla yardım için Dell Teknik Desteği'ni arayın.
4 Donanım sorunlarını giderme Bu bölüm, sisteminizdeki donanım sorunlarını gidermenize yardımcı olur. NOT: Sorun devam ederse yardım için Dell Teknik Destek birimine başvurun.
Çözüm: Sorunu çözmek için şu adımları izleyin: 1 Sistemi kapatın. 2 Tüm güç kablolarını sunucunun güç kaynağı birimlerine ayırın. 3 Sistem kapağını çıkarın. 4 Sabit sürücü arka panelinin tüm kablolarını iki ucundan da çıkarın. 5 Tüm sürücüleri yeniden takın. 6 Sistemin kapağını değiştirin. 7 Güç kablolarını sunucunun güç kaynağı birimlerine takın. 8 Sistemi açın 9 UEFI girmek için F2'ye basın.
4 IDRAC Ayarları Yardımcı Programında, USB Management Port Mode (USB Yönetimi Bağlantı Noktası Modu) seçeneğinin Automatic (Otomatik) veya Standard OS Use (Standart İşletim Sistemi Kullanımı) olarak yapılandırıldığından emin olun. 5 Sorun çözülmezse, klavye ve/veya fareyi çalışan bir klavye veya fare ile değiştirin. Sorun devam ediyorsa sistem bağlı diğer aygıtlarda sorun gidermeye başlamak için adım 6'ya geçin. Sorun çözülmezse sistem bağlı diğer USB aygıtlarda sorun gidermeye geçin.
3 Eğer laptop Windows işletim sistemi ile çalışıyorsa iDRAC Sanal USB NIC aygıt sürücüsünün kurulu olduğundan emin olun. 4 Eğer sürücü kurulmuşsa, iDRAC Direkt yöneltilmeyen bir adres kullandığından WiFi veya kablolu ethernet aracılığıyla herhangi bir ağa bağlı olmadığınızı doğrulayın. Sonraki adım Tüm sorun giderme işlemleri başarısız olursa Yardım Alma bölümüne bakın. Seri Giriş Çıkış aygıtında sorun giderme Adimlar 1 sistem ve seri bağlantı noktasına bağlı tüm çevre birimlerini kapatın.
Islak sistemde sorun giderme Önkoşul DİKKAT: Pek çok tamir işlemi yalnızca sertifikalı servis teknisyeni tarafından gerçekleştirilmelidir. Sorun giderme işlemlerini ve basit tamirleri sadece ürün belgenizde belirtildiği gibi veya destek ekibinin çevrimiçi olarak ya da telefonla belirttiği gibi gerçekleştirmelisiniz. Dell'den yetkili olmayan kişilerden alınan servisten kaynaklanan hasarlar garanti kapsamında değildir. Ürününüz ile birlikte gelen güvenlik talimatlarını okuyun ve uygulayın.
• soğutma örtüsü • genişletme kartı yükselticileri (takılıysa) • genişletme kartları • güç kaynağı birim(ler)i • soğutma fanı takımı (takılıysa) • soğutma fan(lar)ı • İşlemciler ve ısı emiciler • bellek modülleri 4 • sürücü taşıyıcıları veya kafesi Tüm kabloların doğru şekilde takıldığından emin olun. 5 sistem kapağını takın. 6 Uygun tanılama sınama işlemini çalıştırın. Daha fazla bilgi için Sistem tanılamasını kullanma bölümüne bakın.
• Genişletme kartı kurulum yönergelerinin takip edilmesi. Aşağıdaki yöntemlerden biriyle ilave soğutma eklenebilir: iDRAC web GUI'den: 1 Hardware (Donanım) > Fans (Fanlar) > Setup (Kurulum) öğelerine tıklayın. 2 Açılan Fan Speed Offset (Fan Hızı Dengelemesi) listesinden gereken soğutma seviyesi veya minimum fan hızını özel isteğe uyarlanmış bir değer olarak seçin.
5 Sistem kapağını takın. 6 Sistemi ve bağlı çevre birimlerini açın ve USB anahtarının çalışıp çalışmadığını kontrol edin. 7 Sorun çözülmezse adım 2 ve adım 3'ü tekrar edin. 8 Bilinen bir çalışan USB belleği takın. 9 Sistem kapağını takın. Sonraki adım Sorun devam ederse, Yardım Alma bölümüne bakın. Mikro SD kartına yönelik sorun giderme Önkoşul NOT: Bazı mikro SD kartlarda kartın üzerinde fiziksel bir yazma koruması anahtarı bulunur. Yazma koruması anahtarı açıksa mikro SD kartına yazılamaz.
8 sistem kapağını çıkarın. 9 sistem takılı olan tüm genişletme kartlarını çıkarın. 10 sistem kapağını takın. 11 Uygun tanılama sınama işlemini çalıştırın. Sistem tanılamasını kullanma bölümüne bakın. 12 Adım 8'de çıkardığınız her genişletme kartı için aşağıdaki adımları izleyin: Testler başarısız olurlarsa, Yardım Alma bölümüne bakın. a b c d e sistem ve bağlı çevre birimlerini kapatın, sistem elektrik prizinden çıkartın. sistem kapağını çıkarın. Genişletme kartlarından birini yeniden takın.
Depolama denetleyicisine yönelik sorun giderme DİKKAT: Pek çok tamir işlemi yalnızca sertifikalı servis teknisyeni tarafından gerçekleştirilmelidir. Sorun giderme işlemlerini ve basit tamirleri sadece ürün belgenizde belirtildiği gibi veya destek ekibinin çevrimiçi olarak ya da telefonla belirttiği gibi gerçekleştirmelisiniz. Dell'den yetkili olmayan kişilerden alınan servisten kaynaklanan hasarlar garanti kapsamında değildir. Ürününüz ile birlikte gelen güvenlik talimatlarını okuyun ve uygulayın.
İçeri aktarmadan önce yabancı yapılandırmayı görüntülemek için VD Mgmt ekranını kullanabilirsiniz. Yabancı yapılandırmayı görüntüledikten sonra, RAID denetleyicisini temizleyebilir veya içe aktarabilirsiniz. NOT: Yabancı yapılandırmayı içe aktarmadan önce, istediğiniz sonuç olduğunu doğrulamak için ekranda gözden geçirin. Yabancı yapılandırmaları aşağıdaki durumlarda yönetmek için Yabancı Yapılandırma ekranını kullanabilirsiniz: • Yapılandırmadaki tüm fiziksel diskler çıkartılmış veya tekrar takılmış.
a b c Tüm yabancı yapılandırma bilgilerini görüntülemek için Yabancı Yapılandırma Görünümü'nü seçin. İçe Aktarma ve Temizleme seçeneklerini görüntülemek için tuşuna basın. Yabancı yapılandırmaları sanal diske aktarmak için İçe Aktar'ı seçin veya yabancı yapılandırmaları tekrar takılan disklerden silmek için Temizle'yi seçin. İçe aktarma işleminden sonra yeniden oluşturma gerçekleşmez; çünkü diskleri yeniden oluşturmak için hiç artıklı veri yok.
Çözüm: Denetleyici tasarlandığı şekilde çalışıyor. • NVMe PCIe SSD'nin sistemde kurulması ve çıkarılması hakkında daha fazla bilgi için bkz. Donanımın değiştirilmesi ve yapılandırılması. • PCIe SSD adaptörünü yapılandırmak ve yönetmek için bkz. NVMe PCIe SSD Adaptörünüzü Yapılandırma ve Yönetme. 12 Gb/sn sabit sürücü, SAS 6ir RAID denetleyicilerde desteklenmiyor Sorun: 12 Gb/sn sürücü, SAS 6ir RAID denetleyicilerde desteklenmiyor. Çözünürlük: • Denetleyici tasarlandığı gibi çalışmaktadır.
5 Yürütülebilir dosyayı başlatın ve flash yardımcı programı tarafından sağlanan talimatları izleyin. 2. yöntem: Linux DUP için Dell Update paketi talimatları. 1 BIOS güncelleme paketini şu adresten indirin: Dell.com/support. 2 Dosya İndirme penceresi görüntülendiğinde, dosyayı sabit sürücünüze kaydetmek için Save'e (Kaydet) tıklayın. 3 Sürüm bilgilerini shell ortamında "./[model]_BIOS_LX[revision].BIN--version" komutunu çalıştırarak okuyun.
1. yöntem: Windows update paketi: 1 BIOS güncelleme paketini şu adresten indirin: Dell.com/support. 2 Dosya İndirme penceresi görüntülendiğinde, dosyayı sabit sürücünüze kaydetmek için Save'e (Kaydet) tıklayın. 3 Dosyayı indirdiğiniz konuma gidin ve yeni dosyaya çift tıklayın. 4 İletişim penceresinde sunulan sürüm bilgilerini okuyun. 5 Devam etmeden önce iletişim kutusunda belirtilen ön koşulları indirin ve yükleyin. 6 Yükle düğmesine tıklayın.
5 Diski seçmek için boşluk çubuğuna basın. Seçilen fiziksel disklerin yanında X işareti görüntülenir. 6 OK'i (Tamam) seçin. Ürün yazılımı veya fiziksel diskler güncel değil Sorun: Güncel olmayan Ürün Yazılımı veya Sürücüler bilinmeyen disk hatalarıyla sonuçlanıyor Çözüm: • Ürün Yazılımını / PERC Denetleyicisini güncelleyin.
NOT: Korunmuş önbellek varsa, yeni bir sanal disk oluşturma gibi belirli işlemler gerçekleştirilemez. İşletim sistemine önyükleme yapmadan önce sorunu çözmek için BIOS Yapılandırma Yardımcı Programı'na ( ) girmeniz gerekir. Korunmuş önbelleği atmak veya korunmuş önbelleğe sahip sanal diskleri içe aktarmak için BIOS Yapılandırma Yardımcı Programı'na ( ) girmeniz gerektiğini bildiren mesajlar görüntülenir.
3 Güç düğmesini 15 saniye basılı tutun. 4 Tüm kabloları yeniden bağlayın ve sistemi açın. Denetleyicinin düzgün çalıştığından emin olmak için donanım ayrıntılarını kontrol edin. Sabit sürücüde sorun giderme Önkosullar DİKKAT: Bu sorun giderme yordamı, sabit sürücünüzde depolanan verileri silebilir. Devam etmeden önce sabit sürücü üzerinde bulunan tüm verileri yedekleyin. DİKKAT: Pek çok tamir işlemi yalnızca sertifikalı servis teknisyeni tarafından gerçekleştirilmelidir.
geçtiyse, yeniden oluşturma gerçekleşmeden Optimal durumunda içe aktarılır. Birden çok fiziksel diskin manuel olarak yeniden oluşturulmasını gerçekleştirmek için BIOS Yapılandırma Yardımcı Programını veya Dell OpenManage depolama yönetimi uygulamasını da kullanabilirsiniz. 8 Sorun çözülmezse Dell EMC PowerEdge Sunucuları Sorun Giderme Kılavuzu içindeki Sabit sürücü sorunlarını giderme bölümüne bakın.
Rakam 14. PERC Configuration Utility PD Mgmt (PERC Yapılandırma Yardımcı Uygulaması) ekranı Bu tabloda, Sabit sürücü durumu gösterilmiştir Tablo 14. Sabit sürücü durumu Sabit sürücü durumu Açıklama Çevrimdışı Sabit sürücü, RAID dizisinin bir parçası değil. Çevrimiçi Sabit sürücü, RAID dizisinin bir parçası. Hazır Sabit sürücü, RAID dizisinin bir parçası olmaya hazır.
1 Sabit sürücülerin doğru takılıp takılmadığını kontrol edin. 2 Sabit sürücü göstergelerini kontrol edin. Daha fazla bilgi için bkz. Sabit sürücü gösterge kodları bölümü. 3 LED göstergeli sistemler için, tanılama LED'lerini kontrol edin. Daha fazla bilgi için Durum LED göstergeleri bölümüne bakın. NOT: Tanılama LED göstergeleri farklı sistemler için farklı olabilir. 4 LCD panelli sistemlerde aşağıdaki hata kodlarını kontrol edin: Tablo 16.
Belirtiler Sabit disk sürücüsü ses çıkarıyor Açıklama Sabit sürücüden tıkırtı veya yüksek sesli başka gürültüler duyuluyor. Ara sıra ses çıkabilir ve okuma veya yazma işlemleri ile aynı anda veya farklı zamanda olabilir. Çözüm 1 Özel ePSA tanılamasını çalıştırın ve hata kodunu öğrenin. ePSA tanılaması hakkında daha fazla bilgi için bkz. PSA/ePSA Tanılaması. 2 Tanılama başarısız olursa yardım için Dell Teknik Desteği'ni arayın. 3 Tanılama başarılı olursa sabit sürücüyü geri takın.
Optik sürücüde sorun giderme Önkoşul DİKKAT: Pek çok tamir işlemi yalnızca sertifikalı servis teknisyeni tarafından gerçekleştirilmelidir. Sorun giderme işlemlerini ve basit tamirleri sadece ürün belgenizde belirtildiği gibi veya destek ekibinin çevrimiçi olarak ya da telefonla belirttiği gibi gerçekleştirmelisiniz. Dell'den yetkili olmayan kişilerden alınan servisten kaynaklanan hasarlar garanti kapsamında değildir. Ürününüz ile birlikte gelen güvenlik talimatlarını okuyun ve uygulayın.
Sistem belleğinde sorun giderme Önkoşul DİKKAT: Pek çok tamir işlemi yalnızca sertifikalı servis teknisyeni tarafından gerçekleştirilmelidir. Sorun giderme işlemlerini ve basit tamirleri sadece ürün belgenizde belirtildiği gibi veya destek ekibinin çevrimiçi olarak ya da telefonla belirttiği gibi gerçekleştirmelisiniz. Dell'den yetkili olmayan kişilerden alınan servisten kaynaklanan hasarlar garanti kapsamında değildir. Ürününüz ile birlikte gelen güvenlik talimatlarını okuyun ve uygulayın.
Adimlar 1 BIOS'u ve ürün yazılımını güncelleyin. BIOS ve ürün yazılımını güncelleme hakkında daha fazla bilgi için, şu adresteki sistem belgelerine bakın: www.dell.com/support 2 Bellek modüllerini kaldırın ve tekrar takın. 3 Arızayı doğrulamak için MP Bellek testini çalıştırın. 4 Hatalı bellek modülünü sistemde bulunan özdeş başka bir bellek modülüyle değiştirerek veya modülü farklı bir yuvaya takarak izole etmeyi deneyin.
• Bellek modülünü takarken, bellek yerleştirme kurallarına uyduğunuzdan emin olun. Daha fazla bilgi için Bellek yerleştirme yönergeleri bölümüne bakın. • Sistem BIOS'unda ayarlanan bellek yapılandırmalarının, sistemde yüklü bellek modülleriyle eşleştiğinden emin olun. Bellek yerleştirme yönergeleri Sisteminiz, sistemin herhangi geçerli bir yonga seti mimari yapısında yapılandırılabilmesini ve çalışmasını sağlayarak Flexible Memory Configuration (Esnek Bellek Yapılandırmasını) destekler.
Bellek Aynalama Bellek yansıtma modunda, yüklü belleğin yarısı etkin DIMM'leri yansıtmak için kullanılır. Düzeltilemeyen bir hata algılanırsa sistem yansıtılmış kopyaya geçer. Bu mod, SDDC ve çok bitli koruma sağlar ve ayrıca diğer tüm modlara kıyasla en güçlü DIMM güvenilirlik modunu sunar. Bellek Yedekleme Bu modda, kanal başına bir aşama yedek olarak ayrılır. Bir aşamada kalıcı düzeltilebilir hatalar saptanırsa, bu aşamadan gelen veriler yedek aşamaya kopyalanır ve başarısız aşama devre dışı bırakılır.
Bellek modülünü yükselttikten veya kurduktan sonra POST sırasında sistem yanıt vermiyor Sorun: POST sırasında, sistem yanıt vermeyi durduruyor veya MEMTEST şerit hatası veriyor. Resolution (Çözünürlük) Şunlardan emin olun: • Sistemde en son BIOS sürümü kullanılıyor. • Bellek modülleri sistemdeki DIMM soketlerine doğru şekilde oturtulmuştur. • Sistemde hatalı bir DIMM yuvası yoktur. PowerEdge sisteminde POST sırasında bildirilen desteklenmeyen veya uyumsuz bellek modülü hata iletileri nasıl giderilir.
a İstemin kökte olduğundan emin olarak bir cmd istemi açın. b Yardımcı programı bulmak için dir /s dcicfg32.exe yazın. c Bu dizine gidin ve dcicfg32 komutunu çalıştırın = clearmemfailures NOT: Bir SBE varsa, SEL'de kayıtlı yeni bilgiler olacaktır. 3 Bellek hatasını belirlemek için MP Bellek testini çalıştırın. 4 Sorun devam ederse yardım için Dell Teknik Destek birimine başvurun. .
Örneğin, gevşek güç kabloları. 2 Güç kaynağı kolu LED'inin, güç kaynağının düzgün çalıştığını gösterdiğinden emin olun. 3 Sisteminizin yakın zamanda donanımını güncellediyseniz, güç kaynağı ünitesinin, yeni sisteminize yetecek gücü olduğundan emin olun. 4 Yedek güç kaynağı yapılandırması kullanıyorsanız, iki güç kanağınında aynı Watt değerine ve türe sahip olduklarından emin olun. Güç kaynağı LED'li ise, daha yüksek Watt değerine sahip bir güç kaynağı ünitesine yükseltmeye ihtiyacınız olabilir.
Güvenli bir sanal disk oluşturma Bir sanal disk oluşturulduğu sırada nasıl yapılandırıldığına bağlı olarak güvenli veya güvensiz olabilir. Dell PowerEdge RAID Denetleyicisi (PERC) kartları, SED'lerin kaybolması veya çalınması durumunda veri koruması için Kendinden Şifreli Diskleri (SED) destekler. Önkoşul Denetleyicinin bir güvenlik anahtarı olması ve yalnızca SED'leri içermesi gerekir.
RAID Düzeyi Sabit Sürücüsü Sayısı 7,2 K rpm 12 Gbps SAS Sabit Sürücüsü 15 K rpm 6 Gbps SAS Sabit Sürücüsü RAID 10 24 380 GB/saat 500 GB/saat Fiziksel diskler, birden fazla disk aynı anda erişilemez olduktan sonra yeniden oluşturuluyor Bu görev ile ilgili Tek bir dizideki birden fazla fiziksel disk hatası, genellikle kablolama veya bağlantıdaki bir arızayı belirtir ve veri kaybını içerebilir. Birden çok fiziksel disk aynı anda erişilemez olduğunda sanal diski kurtarabilirsiniz.
• Import (İçeri aktar) • Clear (Temizle) NOT: Yabancı görünüm sayfasında Eksik olarak işaretlenmiş hiçbir sabit sürücü olmadığını doğrulayarak sanal diskinizin tüm sabit sürücülere sahip olduğundan ve tüm disklerin içeri aktarılmadan önce beklendiği gibi göründüğünden emin olun. 5 Yabancı yapılandırmayı içeri aktarmak için Import'u (İçeri Aktar) veya silmek için Clear'i (Temizle) seçip Enter tuşuna basın. Yapılandırmayı içeri aktarıyorsanız VD Mgmt ekranı ayrıntılı yapılandırma bilgilerini görüntüler.
Bu görev ile ilgili Bu görev, HBA modunda çalışan PERC donanım denetleyicilerinde desteklenmez. Create Virtual Disk Express Wizard'ı (Sanal Disk Oluşturma Hızlı Sihirbazı) kullanarak sanal disk oluşturmak için aşağıdaki adımları uygulayın: Adimlar 1 Server Administrator (Sunucu Yöneticisi) sayfasının sol üst köşesinde Storage'ı (Depolama) genişletin. 2 PERC Controller'a (PERC Denetleyicisi) tıklayın. 3 Virtual Disks'e (Sanal Diskler) tıklayın.
Adimlar 1 Server Administrator (Sunucu Yöneticisi) sayfasının sağ üst köşesinde Storage (Depolama) öğesine tıklayın. 2 'a tıklayın. 3 Virtual Disks (Sanal Diskler) öğesine tıklayın Virtual Disk(s) on Controller ( üzerindeki Sanal Diskler) sayfası görüntülenir 4 Go to the Create Virtual Disk Wizard (Sanal Disk Oluşturma Sihirbazı'na Git) öğesine tıklayın.
NOT: All Disks (Tüm Diskler) ve Enclosure (Muhafaza) seçenekleri, bunları oluşturan fiziksel diskleri seçtikten sonra açıklıkları düzenlemenizi sağlar. Devam etmeden önce bir açıklığı kaldırabilir ve farklı fiziksel disklerle yeniden bir açıklık belirtebilirsiniz. • Number of Disks per Span (Açıklık Başına Disk Sayısı) — Her bir açıklıktaki disk sayısını seçmenizi sağlar (varsayılan = 2). Bu seçenek yalnızca ürün yazılımı 6.1 ve sonraki sürümlere sahip SAS denetleyicilerinde kullanılabilir.
DİKKAT: Span Edit (Açıklık Düzenle) seçeneğine tıklarsanız, daha önce uygulanmış olan Akıllı Yansıtma geçersiz olur. NOT: Span Edit (Açıklık Düzenle) seçeneği aşağıdaki iki durumda kullanılabilir: • 17 18 Denetleyici, ürün yazılımı 6.1 ve üstü bir SAS denetleyicisi ise. • Sanal disk oluşturma Gelişmiş Sihirbazı kullanırken RAID 10'u seçerseniz.
Rakam 15. Unified Server Configurator'ın RAID yapılandırma sürecinin akış şeması 5 Hızlı seçeneği, sanal disk oluşturma için seçilen RAID türüne bağlı olarak uygun diskleri seçer. Summary (Özet) ekranı görüntülenir. Hızlı sihirbaz sırasında belirlenen seçenekleri gözden geçirebilirsiniz. 6 İşletim sistemi kurulumu için kullanılacak sanal diski oluşturmak için Finish (Son) seçeneğine tıklayın. 7 Advanced (Gelişmiş) seçeneği sizi başka ekranlara götürür.
Dell'in 13. nesil PowerEdge sunucularındaki ESXi ana bilgisayarlarında PERCCLI aracını kullanarak RAID denetleyicisi günlüğünün dışa aktarılmış halini indirme ve yükleme RAID denetleyicisinin ve bağlı sabit sürücülerin durumu hakkında bilgileri dışa aktarmak için PERCCLI aracını kullanabilirsiniz. Dell'in 13.
Rakam 18. Yapılandırma sekmesi a Services properties (Hizmetlerin özellikleri) penceresinde, SSH'yi (1) seçin ve ardından Options... (Seçenekler...) (2) öğesine tıklayın.
Rakam 19. SSH Seçeneklerini Açma b 84 SSH Options (SSH Seçenekleri) penceresinde, Start (Başlat) öğesine (1) ve ardından hizmeti etkinleştirmek için OK(Tamam) öğesine tıklayın (2).
Rakam 20. SSH Hizmetini Başlatma 4 vmware-esx-perccli dosyasını ayıklamak için, PUTTY üzerinden bir SSH bağlantısı açın ve şu komutu çalıştırın: unzip /vmfs/volumes/ datastore1/vmware-esx-perccli-1.05.08.zip PUTTY ücretsiz ve açık kaynaklı bir terminal emülatörü, seri konsol ve ağ dosya transferi uygulamasıdır. SCP, SSH, Telnet, rlogin ve raw soket bağlantısı gibi çeşitli ağ protokollerini destekler. Google'dan indirilebilir. vmware-esx-perccli-1.05.08.vib ve Readme.
Günlük, şu adla oluşturulur: #### MegaSAS.log Rakam 22. Günlük oluşturma 8 Aşağıdaki komutu kullanarak MegaSAS.log dosyasını datastore'a kopyalayın:cp /opt/lsi/perccli/MegaSAS.log /vmfs/volumes/datastore1/ 9 Dosyayı masaüstüne Datastore Browser (Veri Deposu Tarayıcı) ile kopyalayın. Rakam 23. Veri Deposu Tarayıcıda Günlük dosyası Artık günlükler Dell 13. nesil PowerEdge sunucularındaki ESXi ana bilgisayarlarına aktarılıyor.
Adimlar 1 Lifecycle Controller (Yaşam Döngüsü Denetleyicisi) ana sayfasını başlatın, Hardware Configuration (Donanım Yapılandırması) ve ardından Configuration Wizards (Yapılandırma Sihirbazları) öğesine tıklayın. Configuration Wizards (Yapılandırma Sihirbazları) penceresi görüntülenir. 2 Storage Configuration Wizards (Depolama Yapılandırma Sihirbazları) kısmında RAID Configuration (RAID Yapılandırması) öğesine tıklayın.
Denetleyici Monolitik, PERC H310 Mini Blade, PERC H710 Adaptör, PERC H710 Mini Blade, PERC H710 Mini Monolitik, PERC H710P Adaptör, PERC H710P Mini Blade, PERC H710P Mini Monolitik, PERC H810 Adaptör, PERC H330 Adaptör, PERC H330 Mini Monolitik, PERC H330 Mini Blade, PERC H330 Tümleşik, PERC H730 Adaptör, PERC H730 Mini Monolitik, PERC H730 Mini Blade, PERC H730P Adaptör, PERC H730P Mini Monolitik, PERC H730P Mini Blade, PERC H730P İnce, PERC H830 Adaptör, PERC FD33xD/FD33xS Başlangıç RAID Düzeyi Hedef RA
4 Replace'i (Değiştir) seçin. 5 Start'ı (Başlat) seçin. 6 Yedek diski vurgulamak için aşağı ok tuşuna basın ve diski seçmek için boşluk çubuğuna basın. 7 Yerine takmayı başlatmak için OK'e (Tamam) basın. NOT: Yedek disk yabancı yapılandırmaya sahip olmayan bir etkin yedek ya da yapılandırılmamış disk olmalıdır. Aynı veya daha büyük kapasiteye sahip olmalı ve değiştirilen diskle aynı türde olmalıdır. NOT: RAID1 yapılandırmasındaki her fiziksel disk birer birer değiştirilmelidir.
Tablo 19.
NOT: PERC BIOS Configuration Utility (PERC BIOS Yapılandırma Yardımcı Programı) ekranında, HBA modunda çalışan PERC donanım denetleyicilerinde yabancı yapılandırma işlemleri desteklenmez. NOT: Foreign Configuration Operations (Yabancı Yapılandırma İşlemleri) görevi yalnızca ürün yazılımı sürümleri 6.1 ve üzeri olan PERC 6 ve SAS denetleyicilerinde kullanılabilir. NOT: İşletim sistemi, sistemde çalışıyorken harici muhafaza kablosunun çıkarılması önerilmez.
Özellik Tanım • Failed (Arızalı) - Yabancı disk bir hatayla karşılaştı ve artık çalışmıyor. Yabancı yapılandırmayı içe aktaramazsınız. Yabancı yapılandırma aşağıdaki nedenlerden dolayı düşürülmüş veya arızalı durumda olabilir: • • • • • • • Eksik fiziksel disk - Olası sanal diskteki fiziksel disklerden biri eksik veya mevcut değil. Eksik açıklık - Bir karma sanal diskin bir veya daha fazla açıklığı eksik.
Set Patrol Read (Kontrol Okumasını Ayarla) görevi arka planda çalışır ve mümkün olduğunda disk hatalarını düzeltir. Set Patrol Read mode (Kontrol Okuması modunu ayarla) Auto (Otomatik) olarak ayarlandığında denetleyici belirli bir süre boşta kalmışsa ve başka bir arka plan görevi etkin değilse kontrol okuması işlemi başlatılır. Bu senaryoda, disk üzerinde bir giriş/çıkışı etkinliği olmadığında disk hataları belirlenip düzeltilebileceği için kontrol okuması sistem performansını geliştirir.
Tutarlılık Denetimi raporu Tutarlılık denetimi raporu, denetleyici üzerinde yapılan tüm tutarlılık denetimleri ile ilgili kronolojik sıralı bilgi verir. Son çalıştırma saati ve sonuç gibi bilgiler verir. Tutarlılık denetimi başarısız olursa bu hatanın nedenini verir. Tutarlılık Denetimi gerçekleştirme Check Consistency (Tutarlılık Denetimi) görevi yedek (eşlik) bilgilerinin doğruluğunu doğrular. Bu görev yalnızca yedekli sanal diskler için geçerlidir.
Sanal disk sorununu giderme Sanal diskin yeniden oluşturulması çalışmıyor Sanal diskin yeniden oluşturulması aşağıdaki durumlarda çalışmaz: • • • • • • • Sanal disk yedekli değildir - Örneğin, RAID 0 veri yedekliliği sağlamadığı için RAID 0 sanal diski yeniden oluşturulamaz. Sanal diske atanmış bir etkin yedek yoktur - Sanal disk yedekli olduğu sürece, yeniden oluşturmak için: – Arızalanan fiziksel diski çıkarıp değiştirin. Yeni diskte otomatik olarak yeniden oluşturma işlemi başlar.
Minimum boyutlu bir sanal disk Windows Disk Yönetimi'ne görünmüyor Depolama Yönetimi'nde izin verilen en düşük boyutu kullanarak bir sanal disk oluşturursanız o sanal disk, başlatmadan sonra bile Windows Disk Yönetimi'ne görünmeyebilir. Bu durum, Windows Disk Yönetimi son derece küçük sanal diskleri yalnızca dinamik olduklarında tanıyabildiği için oluşur. Depolama Yönetimi'ni kullanırken daha büyük boyutlu sanal diskler oluşturulması önerilir.
4 İmleci Apply (Uygula) düğmesine getirmek için Sekme tuşuna basın, ardından seçimi uygulamak için Enter tuşuna basın. Uyarı etkinleştirilir. Uyarıyı devre dışı bırakmak için Enable Alarm (Uyarıyı Etkinleştir) denetiminin seçimini kaldırmak üzere boşluk tuşunu kullanın ve ardından Apply (Uygula) seçeneğini belirleyin. RAID denetleyicisi çok bitli ECC hataları görüntülüyor Bu görev ile ilgili Açıklama: RAID denetleyicisi, Dell'in 13.
• PERC • SPERC • VRTX anakart • NIC sürücüsü • NIC ürün yazılımı • Anahtar ürün yazılımı Aşağıdaki bağlantılar VRTX için sistem sürücülerini ve ürün yazılımını içerir: VRTX kasa altyapı ürün yazılımı paketi: http://www.dell.com/support/home/us/en/19/drivers/driversdetails?driverId=CPMVM VRTX sürücüleri ve yüklemeler web sitesi: http://www.dell.
– Ctrl + M: SCSI denetleyicileri için (PERC 3, PERC 4). – Ctrl + R: SAS/SATA denetleyicileri için (PERC 5, PERC 6 ve daha yeni denetleyiciler için). – Önbellek içeriğinin temizlenmesine izin vermek için beş dakika bekleyin. – Denetleyici BIOS'una tekrar önyükleme yapın. – Eğer hata ortadan kalktıysa, İşletim Sistemine önyükleyin. – İşletim Sistemi önyüklemesi yine başarısız olduysa ve/veya hata sürüyorsa, bu durum bir işletim sistemi sorununa işaret ediyor olabilir.
• Önbellek Kullanımı Donanım RAID denetleyicileri, normal çalışma için önbelleği (geçici bir bilgi deposu) kullanır. Normal çalışma önbelleği, sistem belleği gibi verileri yalnızca güç açıkken koruyan DRAM belleğinden oluşur. Daha yeni sürüm denetleyiciler ise sunucunun gücü kapalıyken kullanılan NVCache'i kullanır. NVCache belleği hem DRAM belleğini (normal çalışma için) hem de flash belleği (kalıcı) içerir.
Çevrimiçi sürücüdeki veri hatası yeniden oluşturulan sürücüye yayılır (kopyalanır). • Çift Hatanın mevcut olmaması (İkinci hata oluştuğunda veriler kaybolur). Düşürülmüş durumdayken çevrimiçi sürücüde bozuk blok oluşursa bu LBA'da RAID deliği oluşur. Dizide delik oluşmasının bu avantajı, sistemi üretimde kullanılabilir halde tutar ve dizinin yedekliliği geri yüklenir. Etkilenen şeritteki veriler, RAID deliği oluşsa da oluşmasa da kaybolur.
RAID deliğini düzeltme Sorun: Delinmiş RAID dizileri nasıl düzeltilir? Çözüm: Sorunu çözmek için aşağıdaki adımları tamamlayın: UYARI: Bu adımları takip etmek, dizideki tüm verilerin kaybolmasına neden olacaktır. Bu adımları izlemeden önce yedekten veya başka yollardan geri yüklemeye hazır olduğunuzdan emin olun. Bu adımları izlemenin başka dizileri etkilememesine dikkat edin. 1 Varsa Korunan Önbelleği silin. 2 Varsa yabancı yapılandırmaları silin. 3 Diziyi silin.
2 Makineye hava akışının engellenmediğinden emin olun. Kapalı bir alana yerleştirmek veya havalandırma deliğini kapatmak, aşırı ısınmaya neden olabilir. Bir rafa monte edilmişse, raf soğutma sisteminin normal şekilde çalıştığından emin olun. 3 Ortam sıcaklığının kabul edilebilir seviyeler içinde olup olmadığını kontrol edin. 4 Dahili sistem fanlarının engellenmediğinden emin olmak için kontrol edin ve tüm fanların düzgün şekilde döndüğünden emin olun.
5 Sunucu yönetimi yazılımı sorunları Bu bölüm, sunucu yönetimi ile ilgili yazılım sorunlarını yönetmeye yardımcı olur.
• Express (Hızlı) - iDRAC Express (Hızlı), 600 ve üzeri serilerdeki temel yapılandırmanın bir parçası olan standart, varsayılan seçenektir. Lisans yükleme, yedekleme veya lisans yönetimi gerektirmez. Express (Hızlı) sürümü yerleşik araçlar, konsol tümleştirmesi ve basit uzaktan erişim sunar. – Express for Blades (Hızlı Kanatlar) - 12. ve 13. nesil Blade (Kanat) sunucular için yeni bir iDRAC sürümü, Express for Blades (Hızlı Kanatlar) vardır.
• Lisans dosyasını seçin ve Open (Aç) seçeneğine tıklayın. • Yeni lisans dosyasını yükseltmek/değiştirmek için Apply (Uygula) seçeneğine tıklayın. iDRAC8 ile yeni bir PowerEdge sunucusu satın alma işlemi iDRAC7'de yapılan işlemle aynıdır. 600 serisi sunucular ve üzeri için iDRAC Enterprise'da gereken tüm donanım anakartta bulunur. Bu, taşıma sırasında anakartın yerinden çıkması olasılığını ortadan kaldırırken aynı zamanda mümkün olduğunda yükseltme olasılığı da sunar.
NOT: E-posta uyarı ayarlarını yapılandırmadan önce platformun olay filtrelerinin yapılandırılmış olduğundan emin olun. NOT: Posta sunucusu Microsoft Exchange 2007 ise iDRAC etki alanı adını iDRAC'ten uyarı almak için yapılandırmanız gerekir. Sistem saat dilimi senkronize değil iDRAC'te saat dilimini yapılandırabilir ve BIOS veya ana bilgisayar sistem saatleri yerine Ağ Zaman Protokolü (NTP) kullanarak iDRAC saatini yapılandırabilirsiniz.
Lifecycle Controller'ı kullanarak ağ ayarları nasıl yapılandırılır Bu görev ile ilgili Lifecycle Controller'ı kullanarak ağ ayarlarını yapılandırmak için: Adimlar 1 Lifecycle Controller'ı başlatın. 2 Sol bölmede, Settings'e (Ayarlar) tıklayın. 3 Settings (Ayarlar) bölmesinde Network Settings'e (Ağ Ayarları) tıklayın. 4 NIC Card (NIC Kartı) açılan menüsünden yapılandırmak istediğiniz NIC bağlantı noktasını seçin. NOT: Ağ ile iletişim kurmak için aynı anda yalnızca bir NIC kullanabilirsiniz.
OMSA ile etkin yedek atama Genel Etkin Yedek Atama ve Atamayı Kaldırma NOT: Genel etkin yedek sürücüler atamak için Sunucu Yöneticisi'nin en son sürümünü yüklediğinizden emin olun. Daha fazla bilgi için destek sitesinde bulunan Dell EMC OpenManage Yazılım Destek Matrisi'ne bakın. Genel bir etkin yedek, disk grubunun bir parçası olan kullanılmayan bir yedek disktir. Etkin yedekler bekleme modunda kalır.
İşletim sistemi dağıtım sihirbazını kullanarak RAID'i nasıl yapılandırabilirim? RAID'i Dell Lifecycle Controller bir işletim sistemi dağıtım sihirbazı kullanarak yapılandırabilirsiniz. RAID'i yapılandırmak için: • Lifecycle Controller'ı başlatın. • Sol bölmede, OS Deployment (İşletim Sistemi Dağıtımı) öğesine tıklayın. • OS Deployment (İşletim Sistemi Dağıtımı) sayfasında, Deploy OS (İşletim Sistemini Dağıt) öğesine tıklayın.
%100'de tutarlılık denetimi, denetleyici için en yüksek önceliğe sahiptir. Tutarlılık denetimi süresi en aza indirilir ve sistem performansına etkisi maksimumdur. Tutarlılık Denetimi Gerçekleştirme Tutarlılık Denetimi görevi, yedeklilik (eşlik) bilgilerinin doğruluğunu doğrular. Bu görev sadece yedek sanal diskler için geçerlidir. Gerektiğinde, Tutarlılık Denetimi görevi yedekli verileri yeniden oluşturur.
BIOS'u güncellemek için farklı yöntemler hakkında ayrıntılı bilgi için bkz. En.community.dell.com/techcenter/extras/m/white_papers/ 20440526 Ürün yazılımını neden güncelleyemiyorum Bu konuda, ürün yazılımını güncellemenin neden başarılı olmayabileceğine ilişkin bazı nedenler açıklanmıştır. NOT: Genellikle sistem ve bileşenleriniz için en son ürün yazılımını yüklemeniz önerilir. Ürün yazılımı güncellemeleri sistemin performansını, güvenilirliğini ve güvenliğini artırır.
NOT: 64 bit işletim sisteminde, 32 bit ve 64 bit JRE sürümleri desteklenir. 32 bit işletim sisteminde, yalnızca 32 bit JRE sürümü desteklenir. • Linux'ta Java, Sanal Konsol'a erişmek için varsayılan eklenti türüdür. • iDRAC ürün yazılımı güncellendiğinde, Sanal Konsol'u Java eklentisiyle başlatmak başarısız olabilir. Java önbelleğini silin ve Sanal Konsol'u yeniden başlatın.
Otomatik çalıştırma programı otomatik olarak başlamazsa DVD kökündeki otomatik çalıştırma programını veya Dell EMC OpenManage Systems Management Tools and Documentation yazılımının SYSMGMT\srvadmin\windows dizinindeki kurulum programını kullanın. Şu anda desteklenen işletim sistemlerinin listesi için Dell EMC OpenManage Systems Yazılım Destek Matrisi'ne bakın.
SSD algılanmadı Bu görev ile ilgili Katı hal sürücüsü (SSD) sunucu işletim sistemi tarafından algılanmazsa OpenManage Server Administrator dahil tüm ürün yazılımı sürümlerini güncellemeniz gerekir. Ürün yazılımı sürümünü güncellemek için aşağıdakileri yapın: Adimlar 1 Desteklenen ürün yazılımı ve sürücülerin en son sürümleri indirin. En son ürün yazılımını indirme hakkında daha fazla bilgi için Ürün yazılımı ve sürücüleri indirme bölümüne bakın.
iDRAC bağlantı noktasına bir anahtar aracılığıyla bağlanılamıyor iDRAC'ı çeşitli arabirimler ve yöntemlerle kullanabilirsiniz. Arabirimler arasında web arabirimi, RACADM, Redfish, vb gibi seçenekler yer alır. iDRAC'a yerel olarak veya uzaktan bağlanabilirsiniz. iDRAC'a bir anahtar üzerinden iDRAC bağlantı noktasını kullanarak bağlanmayı denerseniz, bağlantının başarılı olması için anahtar üzerinde ek yapılandırma yapmanız gerekebilir.
6 İşletim sistemi sorunlarını giderme Bu bölüm, sisteminizdeki işletim sistemi sorunlarını gidermenize yardımcı olur. NOT: Sorun devam ederse daha fazla yardım için Dell Teknik Desteği'ne başvurun.
Rakam 25. Mavi ekran 2 PSA/ePSA tanılamalarını çalıştırın. Daha fazla bilgi için bkz. PSA/ePSA Tanılaması. 3 Tanılamanın başarılı olmasına rağmen sorun devam ediyorsa mavi ekran hatasının oluştuğu aşamayı belirleyin. 4 Mavi ekran önyükleme işlemi sırasında oluşuyorsa minimum POST bileşenlerini kontrol edin. Daha fazla bilgi için bkz. No POST durumuyla ilgili sorun giderme. Sorun devam ederse Dell Teknik Desteği'ni arayın.
• Önyükleme yapılandırma veritabanını (BCD) görüntülemek veya değiştirmek için bcdedit yardımcı programını kullanın. Daha fazla bilgi için bkz. https://technet.microsoft.com/en-us/library/cc731662.aspx. NOT: Ek kurtarma konsolu komutları için bkz. https://support.microsoft.com/en-us/kb/326215. NOT: Daha fazla sorun giderme adımı için bkz. https://support.microsoft.com/en-us/kb/325375.
POST sırasında bir önyükleme aygıtı yapılandırılırken “İlk Önyükleme Aygıtı ayarlanamıyor” hata iletisi görüntülenir. Açıklama POST modunda "İlk Önyükleme Aygıtı ayarlanamıyor. Sistem BIOS'u güncel değil veya sunucunun ayarların etkili olması için yeniden başlatmaya ihtiyacı var" hata iletisi görüntüleniyor. Resolution (Çözünürlük) Sunucunun tamamen işletim sistemine önyükleme yapmasına izin verin veya ilk önyükleme aygıtına vFlash bölümü ayarlamadan önce sunucuyu kapatın.
NOT: Sunucunun POST gerçekleştirmesi için yeterli zamanı ayırdığınızdan emin olun. Daha yeni sistemlerde POST sırasında herhangi bir görüntünün görüntülenmesi üç dakika kadar sürebilir. Bu süre zarfında, LCD ekranda, sunucunun önyüklendiğini belirten bir mesaj görüntülenir. Adimlar 1 LCD ekranını veya LED göstergelerini hata iletileri için kontrol edin. Sistem bileşenlerini izleyen sistem ürün yazılımı ve aracıları tarafından üretilen olay ve hata iletileri hakkında bilgi için qrl.dell.
NOT: Başka bir kullanıcının OneDrive sitesine bağlanmadan önce, OneDrive'ın sağlandığından (yani OneDrive site sahibinin en az bir kere ziyaret ettiğinden) emin olun ve ya OneDrive site sahibi tarafından verilmiş veya Set-SPOUser commandlet ile alınmış Yönetici izinlerine sahip olduğunuzdan emin olun (http://technet.microsoft.com/en-us/library/ fp161375(v=office.15).aspx).
Operating System Install (İşletim Sistemi Kurulumu) ekranı görüntülenir. 14 Operating System Install (İşletim Sistemi Yükle) ekranında, işletim sistemini seçin ve Next (İleri) üzerine tıklayın. Lisans koşulları penceresi görüntülenir. 15 Lisans anlaşması bilgilerini okuyun. Bilgilerin tümüne katılıyorsanız I accept the license terms (Lisans koşullarını kabul ediyorum) seçeneğini belirleyin ve Next (İleri) seçeneğine tıklayın.
7 Yüklemek istediğiniz işletim sistemini seçin ekranında, sağlanan listeden işletim sistemini seçin ve İleri üzerine tıklatın. Lisans koşulları penceresi görüntülenir. 8 Lisans sözleşmesi bilgilerini okuyun. Açıklamaların tümüne katılıyorsanız I accept the license terms (Lisans koşullarını kabul ediyorum) seçeneğini belirleyin ve sonra Next (İleri) üzerine tıklayın.
Resolution (Çözünürlük) 1 System Setup (Sistem Kurulumu) kısmında, Integrated Device Settings (Tümleşik Aygıt Ayarları) ekranındaki USB 3.0 seçeneğinin Disable (Devre Dışı) olarak ayarlandığından emin olun. NOT: Varsayılan olarak, USB 3.0 seçeneği devre dışıdır. Etkinleştirildiğinde, işletim sistemi klavye, fare ve USB DVD gibi USB aygıtlarını algılayamaz. Windows Server 2008 R2 SP1, USB 3.0 için kutudan çıkan sürücüleri destekler ve şu adreste bulunabilirler: www.dell.com/support.
Neden Bu sorun, Windows Server 2008 R2, Grafik Çıktı Protokolü'nü (GOP) desteklemediği için oluşur. Çözüm BIOS yapılandırma yardımcı programında, Miscellaneous Settings (Çeşitli Ayarlar) ekranında Load Legacy Option Rom (Eski İsteğe Bağlı ROM'u Yükle) seçeneğinin Enable (Etkin) olarak ayarlandığından emin olun. Sisteminizi yeniden başlatın ve işletim sistemine yeniden önyükleyin.
Ana veri yolu bağdaştırıcısı mini için Windows'ta fiziksel diskler ve arka panel eksik Sorun- HBA330 mini kartı destekleyen bir sunucu platformunda aşağıdaki değişikliklerden herhangi birini yaparsanız: • R730XD'nin arka panelini bütünleşik bir denetleyiciye taşımak. • Bir HBA330 mini aygıtını belirli bir arka panel yapılandırması olan bir sunucudan farklı arka panel yapılandırmasına sahip bir sunucuya taşımak. Windows yüklendikten sonra, işletim sistemi bir fiziksel disk algılamaz.
Dahili Çift SD modülü ile Microsoft Hyper-V Server 2012 R2'yi yükleyin Önkosullar • Dahili Çift SD modülünde (IDSDM) bulunan Yansıtma modunda Çift 8 GB veya 16 GB SD kartlı Dell EMC 13. Nesil PowerEdge sunucuları. • Önyükleme Modunu UEFI'ye değil Bios'a ayarlayın. • Hyper-V Server 2012 R2 ISO'yu Microsoft'tan indirin. Bu görev ile ilgili IDSM kullanarak Microsoft Hyper-V server 2012 R2'yi yüklemek için. Adimlar 1 USB Modunun USB 3.
VMware SSS VM'ler neden ESXi 6.0'da korunmayan bir durumda Hata Toleransı ile yapılandırılmış? AMD 6300 serisi işlemcili bazı PowerEdge sistemleri için Hata Toleransı (FT) ile yapılandırılmış VM'ler korumalı bir durumda olmayabilir. Bazen, ikincil VM korumalı duruma ulaşmak için daha fazla zaman alır. Bu bilinen bir sorundur. Etkilenen sistemler arasında PowerEdge sistemleri R815, R715 ve M915 bulunur.
Bu bölümde verilen yedekleme ve geri yükleme adımları aşağıdakileri varsayar: • vSphere CLI'yi zaten yedeklemek veya geri yüklemek istediğiniz sistemden başka bir sisteme içeri aktardınız. • Windows veya Linux yönetim Uygulama Programlama Arabirimlerini (APIs) yüklediniz. ESXi ana bilgisayarınızın yapılandırmasını yedekleme Bu görev ile ilgili Bir ana bilgisayarın yapılandırma verilerini yedeklemek için: Adimlar 1 vSphere CLI'yi başlatın.
Windows işletim sisteminde Fusion-IO sürücülerini yükleme, güncelleme ve yönetme Issue (Sorun): Müşteri ioSphere yüklemeye çalışıyor ve parola kimlik bilgileriyle ilgili sorun yaşıyor. Corrective action (Düzeltici eylem): Sorunu çözmek için, ioSphere'in yeniden yüklenmesi gerekiyor. Aşağıdaki bağlantı, ioSphere'ı yükleme hakkında bilgiler içeren Fusion-IO'yu yükleme, güncelleme ve yönetme hakkında bilgiler içerir: http://www.dell.
Statik IPv6 adresi başlatıcıya atandığında, başarılı yükleme sonrasında SUSE Linux Enterprise Server 12, IPv6 adresi üzerinden iSCSI'dan başlatılmıyor. Çözüm Başlatıcı için Dinamik Ana Bilgisayar Yapılandırma Protokolü (DHCP) adresini kullanın. İşletim sistemini çeşitli yöntemlerle kurma İşletim sistemini Dell Yaşam Döngüsü Denetleyicisi ve çeşitli yöntemlerle kurun ve dağıtın, aşağıda listelenen videoları izleyin: Tablo 22.
Slno Video Açıklaması Konum 17. İşletim Sistemi Dağıtımı - NFS Kullanarak Katılımsız Yükleme - Ağ Dosya Sistemi İşletim Sistemi Dağıtımı - NFS Kullanarak Katılımsız Yükleme 18. İşletim Sistemi Dağıtımı - CIFS Kullanarak Katılımsız Yükleme - Ortak İnternet Dosya Sistemi İşletim Sistemi Dağıtımı - CIFS Kullanarak Katılımsız Yükleme 19. İşletim Sistemi Dağıtımı - USB Sürücü Kullanarak Katılımsız Yükleme İşletim Sistemi Dağıtımı - USB Sürücü Kullanarak Katılımsız Yükleme 20.
7 Yardım alma Konular: • Dell EMC ile iletişime geçme • Sürücüleri ve ürün yazılımını indirme • Sisteminizin Servis Etiketini bulma Dell EMC ile iletişime geçme Dell EMC İnternet üzerinden ve telefonla çeşitli destek ve hizmet seçenekleri sunmaktadır. Etkin bir İnternet bağlantınız yoksa satın alma faturanız, sevk irsaliyeniz, fişiniz veya Dell EMC ürün kataloğu ile ilgili iletişim bilgilerini bulabilirsiniz.
4 Sürücüleri veya ürün yazılımını bir USB sürücüsüne, CD'ye veya DVD'ye indirin. Sisteminizin Servis Etiketini bulma Sisteminiz, eşsiz bir Hızlı Servis Kodu ve Servis Kodu numarası ile tanımlanır. Hızlı Servis Kodu ve Servis Etiketi, bilgi etiketini çıkarınca sistemin ön tarafında bulunur. Alternatif olarak, bilgi sistemin kasası üzerindeki bir çıkartma üzerinde olabilir. Mini Kurumsal Servis Etiketi (EST) sistemin arkasında bulunur.