Dell™ PowerEdge™ R310 시스템 하드웨어 소유자 매뉴얼 규정 모델 : E07S 시리즈 규정 유형 : E07S002
주, 주의 및 경고 주: 주는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제 공합니다. 주의: 주의는 지침을 준수하지 않을 경우의 하드웨어 손상이나 데이터 손실 위험을 설명합니다. 경고: 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험 이 있음을 알려줍니다. ____________________ 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다. © 2010 Dell Inc. 저작권 본사 소유. Dell Inc.의 서면 승인 없이 어떠한 방식으로든 본 자료를 무단 복제하는 행위는 엄격히 금지됩 니다. 본 설명서에 사용된 상표인 Dell, DELL 로고 및 PowerEdge는 Dell Inc.의 상표이며, Microsoft, Windows, Windows Server 및 MS-DOS는 미국 및/또는 기타 국가에서 Microsoft Corporation의 상 표 또는 등록 상표입니다.
차례 1 시스템 정보 . . . . . . . . . . . . . . . . . . . . . . . 시작하는 동안 시스템 기능에 액세스 11 . . . . . . . . 11 전면 패널 기능 및 표시등 . . . . . . . . . . . . . . . 12 LCD 패널 기능 (선택 사양) . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . 16 Home (홈) 화면 . Setup (설치) 메뉴 . . . . . . . . . . . . . . . . . 16 View (보기) 메뉴 . . . . . . . . . . . . . . . . . . 17 하드 드라이브 상태 표시등 . . . . . . . . . . . . . . 18 . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . 21 . . . . .
2 진단 메시지 . . . . . . . . . . . . . . . . . . . . . . . 51 경고 메시지 . . . . . . . . . . . . . . . . . . . . . . . 51 시스템 설치 프로그램 및 UEFI 부팅 관리자 사용 . . 시스템 부팅 모드 선택 . . . . . . . . . . . . . 53 . . . . . . . . . . . . . . . . . 53 시스템 설치 프로그램 시작 오류 메시지에 응답 . . . . . . . . . . . . . . 54 . . . . . . . . . . . . . . . . 54 시스템 설치 프로그램 탐색 키 사용 . . . . . . . 54 . . . . . . . . . . . . . . 55 . . . . . . . . . . . . . . . . . . . . . 55 시스템 설치 프로그램 옵션 기본 화면 . Memory Settings (메모리 설정) 화면 . .
내장형 시스템 관리. . . . . . . . . . . . . . . . . . . 베이스보드 관리 컨트롤러 구성 . . . . . . . . . . . 73 . . . . . . . . . . . . . . . 73 . . . . . . . . . . . . . . . . . 74 BMC 설치 모듈 시작 iDRAC 구성 유틸리티 . iDRAC 구성 유틸리티 시작 3 . . . . . . . . . . . . 74 . . . . . . . . . . . . . . . 75 . . . . . . . . . . . . . . . . . . . . . . . . 75 시스템 구성요소 설치 권장 도구 72 시스템 내부 . . . . . . . . . . . . . . . . . . . . . . . 전면 베젤 (선택 사양) 75 . . . . . . . . . . . . . . . . . 77 . . . . . . . . . . . . . . . . . .
확장 카드 . . . . . . . . . . . . . . . . . . . . . . . . 확장 카드 설치 지침 . . . . . . . . . . . . . . . . 91 확장 카드 설치 . . . . . . . . . . . . . . . . . . . 93 확장 카드 분리 . . . . . . . . . . . . . . . . . . . 95 . . . . . . . . . . . . . . . . . . . . 96 확장 카드 라이저 확장 카드 라이저 분리 . . . . . . . . . . . . . . 96 확장 카드 라이저 설치 . . . . . . . . . . . . . . 98 . . . . . . . . . . . . . . . . . . 98 내부 USB 메모리 키 . 냉각기 덮개 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VFlash 매체 (선택 사양) . . . . . . . . . . . . . . . . 117 VFlash 매체 카드 설치 . . . . . . . . . . . . . . . 117 VFlash 매체 카드 분리 . . . . . . . . . . . . . . . 117 . . . . . . . . . . . . . . . . . . . . . . . . 117 프로세서 . 프로세서 분리 . . . . . . . . . . . . . . . . . . . 117 프로세서 설치 . . . . . . . . . . . . . . . . . . . 121 . . . . . . . . . . . . . . . . . . . . . 122 전원 공급 장치 중복 전원 공급 장치 분리 . . . . . . . . . . . . 122 중복 전원 공급 장치 설치 . . . . . . . . . . . . 124 전원 공급 장치 보호물 분리 . . . . . . .
4 시스템 문제 해결 . . . . . . . . . . . . . . . . . . 안전 제일 — 사용자와 사용자 시스템의 안전을 위하여 . . . . . . . . . . . . . . . . . . . . . 139 . . . . . . . . . . . . . 139 . . . . . . . . . . . . . . . . . 139 시스템 시작 오류 문제 해결 외부 연결 문제 해결 비디오 하위 시스템 문제 해결 . USB 장치 문제 해결 . . . . . . . . . . . . 140 . . . . . . . . . . . . . . . . . 140 직렬 I/O 장치 문제 해결 NIC 문제 해결 . . . . . . . . . . . . . . . 141 . . . . . . . . . . . . . . . . . . . . . 141 습식 시스템 문제 해결 . . . . . . . . . . . . . . . . 손상된 시스템 문제 해결 .
5 시스템 진단 프로그램 실행 온라인 진단 프로그램 사용 . . . . . . . . . . . . . . . . . . . . . . . . 내장형 시스템 진단 프로그램 기능 . 156 . . . . . . . . . 156 . . . . . . . . . . . 156 . . . . . . . . . . . . . 157 . . . . . . . . . . . . . . . . . 157 시스템 진단 프로그램 검사 옵션 사용자 정의 검사 옵션 사용 . 진단 프로그램 옵션 선택 . 정보 및 결과 보기 . 점퍼 및 커넥터 . . . . . . . . . . . . . 157 . . . . . . . . . . . . . . . . 157 . . . . . . . . . . . . . . . . . . . 시스템 보드 점퍼 . 색인 160 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
차례
시스템 정보 시작하는 동안 시스템 기능에 액세스 시작하는 동안 시스템 기능에 액세스하려면 다음 키를 입력합니다. 키 입력 설명 시스템 설치 프로그램을 시작합니다. 53페이지의 "시스템 설치 프 로그램 및 UEFI 부팅 관리자 사용"을 참조하십시오. 시스템 서비스를 시작하여 Unified Server Configurator를 엽니다. Unified Server Configurator를 사용하여 내장형 시스템 진단 프로그 램과 같은 유틸리티에 액세스할 수 있습니다. 자세한 내용은 support.dell.com/manuals의 Unified Server Configurator 설명서를 참조하십시오. 시스템의 부팅 구성에 따라 BIOS 부팅 관리자 또는 UEFI 부팅 관 리자를 시작합니다. 53페이지의 "시스템 설치 프로그램 및 UEFI 부 팅 관리자 사용"을 참조하십시오. PXE 부팅을 시작합니다.
전면 패널 기능 및 표시등 주: 구성에 따라 시스템에 LCD 패널 또는 LED 진단 표시등이 있을 수 있습니다. 이 항목의 그림에서는 LCD 패널이 있는 시스템을 보여 줍니다. 그림 1-1. 1 전면 패널 기능 및 표시등 2 3 4 5 6 7 9 8 10 11 1 2 3 4 1 항목 표시등, 단추 또는 커넥터 1 전원 표시등, 전원 단추 아이콘 EST 2 3 설명 시스템 전원이 켜진 상태이면 전원 표 시등이 켜집니다. 전원 단추는 시스템으로의 DC 전원 공 급 장치의 출력을 제어합니다. 선택 사 양인 시스템 베젤이 설치되면 전원 단 추에 접근할 수 없게 됩니다. 주: 시스템에 설치된 메모리 양에 따라 시스템 전원을 켤 때 비디오 모니터에 이미지가 표시되는 데 몇 초에서 2분 이 상까지 걸릴 수 있습니다. 주: ACPI를 지원하는 운영 체제에서 전 원 단추를 사용하여 시스템을 끄면 시 스템에 대한 전원 공급이 끊어지기 전 에 점진적 종료가 수행됩니다.
항목 표시등, 단추 또는 커넥터 2 NMI 단추 아이콘 설명 특정 운영 체제를 사용하는 경우 소프 트웨어 및 장치 드라이버 오류 문제를 해결하는 데 사용됩니다. 이 단추는 종 이 클립의 끝 부분을 사용하여 누를 수 있습니다. 공인된 지원 담당자가 지시하거나 운 영 체제 설명서에 명시된 경우에만 이 단추를 사용합니다. 3 비디오 커넥터 모니터를 시스템에 연결합니다. 4 하드 드라이브 작동 표시등 하드 드라이브가 사용 중일 때 켜집니다. 5 LED 또는 LCD 패널 주: 구성에 따라 시스템에 LED 진단 표시 등이나 LCD 패널이 사용될 수 있습니다. LED 패널: 시스템 시동 시 진단 표시등 4개를 통해 오류 코드가 표시됩니다. 23페이지의 "진단 표시등 (선택 사양)" 을 참조하십시오. LCD 패널: 시스템 ID, 상태 정보 및 시 스템 오류 메시지를 제공합니다. LCD 패널에 대한 자세한 내용은 14페 이지의 "LCD 패널 기능 (선택 사양)"을 참조하십시오.
항목 표시등, 단추 또는 커넥터 아이콘 설명 7 시스템 상태 표시등 정상적으로 시스템이 작동할 때는 청 색으로 켜집니다. 문제가 발생하여 시 스템에 주의가 필요한 경우에는 호박 색으로 켜집니다. 8 USB 커넥터 (2개) USB 장치를 시스템에 연결합니다. 포트는 USB 2.0을 지원합니다. 9 하드 드라이브 (4개) 3.5인치 HDD 핫 스왑 가능 캐리어에 2.5인치 드라이브 최대 4개 또는 3.5인 치 케이블/핫 스왑 가능 하드 드라이브 최대 4개. 10 시스템 확인 패널 특급 서비스 태그, 내장형 NIC의 MAC 주소, iDRAC6 Enterprise 카드의 MAC 주소 등 시스템 정보에 관한 슬라이드 형 패널. 11 광학 드라이브 (선택 사양) 선택 사양인 슬림형 SATA DVD-ROM 드라이브 또는 DVD+/-RW 드라이브 1개. 주: DVD 장치는 데이터 전용입니다.
그림 1-2. LCD 패널 기능 1 2 3 4 항목 단추 설명 1 Left (왼쪽) 뒤쪽으로 커서를 한 단계 이동합니다. 2 Select (선택) 커서에 의해 강조 표시된 메뉴 항목을 선택합 니다. 3 Right (오른쪽) 앞쪽으로 커서를 한 단계 이동합니다. 메시지가 스크롤되는 동안 다음을 수행할 수 있습니다. • 한 번 누르면 스크롤 속도가 증가합니다. • 한 번 더 누르면 스크롤이 멈춥니다. • 다시 한 번 더 누르면 기본 스크롤 속도로 돌 아옵니다. • 다시 누르면 이 과정이 반복됩니다. 4 System ID (시스템 ID) 시스템 ID 모드를 켜거나 (LCD 패널이 청색 으로 깜박임) 끕니다. 시스템 ID를 켜거나 끄려면 빠르게 누릅니다. POST 중에 시스템이 중지될 경우에 시스템 ID 단추를 5초 이상 누르면 BIOS Progress (BIOS 진행) 모드가 시작됩니다.
Home (홈) 화면 Home (홈) 화면에는 사용자가 설정할 수 있는 시스템 정보가 표시됩니다. 상태 메시지나 오류 없이 정상적으로 시스템이 작동할 때 이 화면이 표시 됩니다. 시스템이 대기 모드에 있을 때 오류 메시지 없이 5분 이상 비활성 상태가 지속되면 LCD의 후광이 꺼지게 됩니다. 3개의 탐색 단추 (Select (선택), Left (왼쪽) 또는 Right (오른쪽)) 중 하나를 누르면 Home (홈) 화면 이 표시됩니다. 다른 메뉴에서 Home (홈) 화면으로 이동하려면 Home (홈) 아이콘이 표시될 때까지 위쪽 화살표를 누른 다음 Home (홈) 아이콘을 선택합 니다. Setup (설치) 메뉴 옵션 설명 DHCP 또는 Static IP (고정 IP) 를 선택하여 네트워크 모드를 구성합니다. Static IP (고정 IP) 를 선택하면 IP, 주: iDRAC6 Express 카드가 서브넷 (Sub) 및 게이트웨이 (Gtw) 필드를 사용할 수 시스템에 설치되면 BMC 옵 있습니다.
View (보기) 메뉴 옵션 설명 선택 사양인 iDRAC6에 대한 IPv4 또는 IPv6 주소를 표시 합니다. 주소에는 DNS (기본 및 보조), 게이트웨이, IP 주: iDRAC6 Express 카드가 및 서브넷 (IPv6는 서브넷이 없음) 이 포함됩니다. 시스템에 설치되면 BMC IP 주: BMC IP는 IPv4 주소만 지원합니다. 옵션은 DRAC IP로 교체됩 니다. BMC IP or DRAC IP (BMC IP 또는 DRAC IP) MAC DRAC, iSCSIn 또는 NETn의 MAC 주소를 표시합니다. 주: 시스템에 iDRAC6 Express 카드가 설치되어 있지 않 은 경우에는 MAC 옵션에 BMC, iSCSIn 또는 NETn의 MAC 주소가 표시됩니다. Name (이름) 시스템의 호스트 이름, 모델 이름 또는 사용자 문자열 을 표시합니다. Number (번호) 시스템의 자산 태그 또는 서비스 태그를 표시합니다.
하드 드라이브 상태 표시등 그림 1-3. 하드 드라이브 표시등 2 1 1 드라이브 상태 표시등 (녹색 및 호박색) 2 드라이브 작동 표시등 (녹색) 드라이브 상태 표시등 패턴 (RAID에만 해당) 상태 녹색 표시등이 초당 2번 깜박임 드라이브 식별/분리 준비 상태 꺼짐 드라이브 삽입 또는 분리 대기 상태 주: 드라이브 상태 표시등은 시스템 전원 이 공급된 후에 모든 하드 드라이브가 초 기화될 때까지 꺼진 상태를 유지합니다. 그 동안에는 드라이브를 삽입하거나 분 리할 수 없습니다.
후면 패널 기능 및 표시등 그림 1-4에서는 시스템 후면 패널의 제어부, 표시등 및 커넥터를 보여 줍니다. 그림 1-4. 후면 패널 기능 및 표시등 1 2 3 4 5 1 6 7 8 9 10 11 12 2 Gb 1 아이콘 Gb 2 항목 표시등, 단추 또는 커넥터 설명 1 VFlash 매체 슬롯 (선택 사양) iDRAC6 Enterprise 카드 (선택 사양) 용 외부 SD 메모리 카드를 연결합니다. 2 iDRAC6 Enterprise 포 트 (선택 사양) iDRAC6 Enterprise 카드 (선택 사양) 전용 관리 포트입니다. 3 직렬 커넥터 직렬 장치를 시스템에 연결합니다. 4 비디오 커넥터 VGA 디스플레이를 시스템에 연결합 니다. 5 USB 커넥터 (2개) USB 장치를 시스템에 연결합니다. 포트는 USB 2.0을 지원합니다.
항목 표시등, 단추 또는 커넥터 9 시스템 상태 표시등 아이콘 설명 정상 시스템 작동 중에는 청색으로 켜 집니다. 시스템 관리 소프트웨어 및 시스템의 전면과 후면에 있는 확인 단추는 특정 시스템을 식별할 때 표시등이 청색으 로 깜박이게 합니다. 문제가 발생하여 시스템에 주의가 필 요한 경우에는 호박색으로 켜집니다. 10 시스템 확인 단추 시스템 ID 모드를 켜고 끕니다. 전면과 후면 패널의 확인 단추를 사용 하여 랙에서 특정 시스템의 위치를 찾 을 수 있습니다. 단추 중 하나를 누르 면 단추를 한 번 더 누르기 전까지 전 면의 LCD 패널과 후면의 시스템 상태 표시등이 청색으로 깜박입니다.
외부 장치 연결 지침 • 새 외부 장치를 연결하기 전에 시스템 및 외부 장치의 전원을 끕니다. 그런 다음 장치 설명서에 별도로 언급된 사항이 없으면 외부 장치를 켠 다음 시스템을 켭니다. • 연결한 장치에 적합한 드라이버가 시스템에 설치되어 있는지 확인합 니다. • 필요하면 시스템 설치 프로그램을 사용하여 해당 시스템의 포트를 활 성화합니다. 54페이지의 "시스템 설치 프로그램 시작"을 참조하십시오. NIC 표시등 코드 그림 1-5. NIC 표시등 코드 1 1 2 링크 표시등 2 작동 표시등 표시등 표시등 코드 링크 표시등 및 작동 표 시등이 꺼져 있음 NIC가 네트워크에 연결되지 않았습니다. 링크 표시등이 녹색으로 NIC가 올바른 네트워크 링크에 1000Mbps로 연결되어 켜짐 있습니다. 링크 표시등이 호박색으 NIC는 올바른 네트워크 링크에 10/100Mbps로 연결되 로 켜짐 어 있습니다. 작동 표시등이 녹색으로 네트워크 데이터를 전송하거나 수신하는 중입니다.
전원 표시등 코드 전원 공급 장치에는 전원 공급 여부 및 전원 결함 발생 여부를 보여 주는 표 시등이 있습니다. • 꺼짐 — AC 전원이 연결되어 있지 않습니다. • 녹색 — 대기 모드에서는 유효한 AC 전원이 전원 공급 장치에 연결되어 있고 전원 공급 장치가 작동 중임을 나타냅니다. 또한, 시스템이 켜져 있 는 상태라면 전원 공급 장치가 시스템에 DC 전원을 공급 중임도 나타냅 니다. • 호박색 — 전원 공급 장치에 문제가 있음을 나타냅니다. • 녹색과 호박색으로 교대로 켜짐 — 핫 애드하는 전원 공급 장치가 다른 쪽 전원 공급 장치와 불일치함을 나타냅니다 (고출력 전원 공급 장치와 Energy Smart 전원 공급 장치가 같은 시스템에 설치된 경우입니다). 표 시등이 깜박이는 전원 공급 장치를 기존에 설치된 다른 쪽 전원 공급 장 치의 용량과 일치하는 제품으로 교체하십시오. 그림 1-6.
진단 표시등 (선택 사양) 시스템 전면 패널에 있는 4개의 진단 표시등이 시스템 시작 도중 오류 코드 를 표시합니다. 표 1-1에서는 이러한 코드와 관련된 원인 및 가능한 수정 조치 목록을 보여 줍니다. 강조 표시된 주기는 표시등이 켜져 있음을 나타 내고 강조 표시되지 않은 주기는 표시등이 꺼져 있음을 나타냅니다. 표 1-1. 진단 표시등 코드 코드 원인 수정 조치 시스템이 정상적으로 꺼 작동 중인 전원 콘센트에 시스템을 연결하고 전원 단추를 누릅니다. 진 상태이거나 사전 BIOS 오류가 발생했을 수 있습니다. 시스템에서 운영 체제로 성공적으로 부팅한 후에 는 진단 표시등이 켜지지 않습니다. POST 후에 컴퓨터가 정 참조용으로만 제공됩니다. 상적인 작동 상태입니다. BIOS 검사 합 오류가 감 163페이지의 "도움말 얻기"를 참 지되었습니다. 시스템이 조하십시오. 복구 모드 상태입니다. 프로세서 오류일 수 있습 154페이지의 "프로세서 문제 해 니다. 결"을 참조하십시오. 메모리 오류입니다.
코드 원인 수정 조치 하드 드라이브 오류. 디스켓 드라이브 및 하드 드라이브 가 올바르게 연결되었는지 확인합 니다. 시스템에 설치된 드라이브에 대한 내용은 82페이지의 "하드 드 라이브"를 참조하십시오. USB 오류일 수 있습니다. 140페이지의 "USB 장치 문제 해 결"을 참조하십시오. 메모리 모듈이 감지되지 147페이지의 "시스템 메모리 문 않습니다. 제 해결"을 참조하십시오. 시스템 보드 오류. 163페이지의 "도움말 얻기"를 참 조하십시오. 메모리 구성 오류. 147페이지의 "시스템 메모리 문 제 해결"을 참조하십시오. 시스템 보드 리소스 및/ 163페이지의 "도움말 얻기"를 참 또는 하드웨어 오류일 수 조하십시오. 있습니다. 시스템 리소스 구성 오류 163페이지의 "도움말 얻기"를 참 일 수 있습니다. 조하십시오. 기타 오류. 24 시스템 정보 광학 드라이브 및 하드 드라이브 가 올바르게 연결되어 있는지 확 인합니다.
LCD 상태 메시지 (선택 사양) 시스템이 올바르게 작동하거나 시스템에 문제가 발생함을 알릴 경우 시스 템 제어판 LCD는 상태 메시지를 표시합니다. LCD는 정상적인 작동 상태를 나타낼 경우 청색으로 켜지고 오류 상태를 나 타낼 경우에는 호박색으로 켜집니다. LCD는 설명 문자가 따른 상태 코드를 포함한 메시지를 표시합니다. 다음 표에서는 LCD 상태 메시지와 메시지에 따라 가능한 원인의 목록을 표시합니다. LCD 메시지는 SEL (시스템 이벤 트 로그) 에 기록된 이벤트를 나타냅니다. SEL 및 시스템 관리 설정 구성에 대한 자세한 내용은 시스템 관리 소프트웨어 설명서를 참조하십시오. 주: 시스템이 부팅할 수 없는 경우 오류 코드가 LCD에 표시될 때까지 시스템 ID 단추를 최소 5초 동안 누릅니다. 코드를 기록한 다음 163페이지의 "도움말 얻기"를 참조하십시오. 표 1-2.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 수정 조치 E1116 Memory disabled, temp above range. Power cycle AC. 메모리의 온도가 허용치를 초과했으며 구성요소에 대 한 손상을 방지하기 위해 비활성화되었습니다. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. 145페이지의 "시스템 냉 각 문제 해결"을 참조하 십시오. 문제가 지속되면 163페이지의 "도움말 얻 기"를 참조하십시오. E1210 Motherboard CMOS 전지가 없거나 전 144페이지의 "시스템 전 battery 압이 허용 범위를 벗어났 지 문제 해결"을 참조하 failure. Check 습니다. 십시오. battery. E1211 RAID RAID 전지가 없거나 불 Controller 량이거나 온도 문제로 재 battery 충전할 수 없습니다. failure. Check battery.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 E122A CPU # VTT Regulator failure. Reseat CPU. 수정 조치 지정된 프로세서 VTT 전 프로세서를 다시 장착합 압 조정기에서 오류가 발 니다. 154페이지의 "프로 생했습니다. 세서 문제 해결"를 참조 하십시오. 문제가 지속되면 163페 이지의 "도움말 얻기"을 참조하십시오. E122C CPU Power Fault. Power cycle AC. 프로세서 전원을 켤 때 전 10초 동안 시스템에서 원 오류가 감지되었습니다. AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E122D Memory 메모리 조정기 중 하나에 Regulator # 서 오류가 발생했습니다. Failed. Reseat DIMMs. 메모리 모듈을 다시 장착 합니다. 147페이지의 "시 스템 메모리 문제 해결" 을 참조하십시오.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 E1313 Fan redundancy 시스템의 팬이 더 이상 중 lost. Check 복되지 않습니다. 다른 팬 fans. 에도 오류가 발생하면 시 스템이 과열될 위험이 있 습니다. 원인 수정 조치 LCD에 추가로 스크롤되 는 메시지가 있는지 확인 합니다. 146페이지의 "팬 문제 해결"을 참조하십 시오. E1410 Internal Error 지정된 프로세서에서 내부 detected. 오류가 발생했습니다. 이 Check "FRU X". 오류는 프로세서에 의해 발생한 것일 수 있으나 그 렇지 않을 수도 있습니다. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E1414 CPU # temp exceeding range. Check CPU heatsink. 지정된 프로세서가 적정 온 프로세서 방열판이 올바 도 범위를 벗어났습니다.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 E1420 CPU Bus parity 시스템 BIOS에서 프로세 10초 동안 시스템에서 error. Power 서 버스 패리티 오류를 보 AC 전원을 분리하고 시 cycle AC. 고했습니다. 스템을 재시작합니다. 원인 수정 조치 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E1422 CPU # machine check error. Power cycle AC. 기계 검사 오류가 시스템 10초 동안 시스템에서 BIOS에 보고되었습니다. AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E1610 Power Supply # 지정한 전원 공급 장치가 145페이지의 "전원 공급 (### W) 제거되었거나 시스템에 장치 문제 해결"을 참조 missing. 서 찾을 수 없습니다. 하십시오. Check power supply.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 E1620 Power Supply # 지정된 전원 공급 장치의 (### W) AC AC 입력이 허용 범위를 power error. 벗어났습니다. Check PSU cables. 원인 수정 조치 E1624 Lost power supply redundancy. Check PSU cables. E1626 Power Supply 시스템에 있는 전원 공급 Mismatch. PSU1 장치의 와트가 동일하지 = ### W, PSU2 않습니다. = ### W. 설치된 전원 공급 장치가 일치하는 와트를 가지고 있는지 확인합니다. 시스 템의 시작 안내서에 설명 된 기술 사양을 참조하십 시오. E1629 Power required > PSU wattage. Check PSU and config. 시스템 구성이 스로틀 상 태인 경우에도 전원 공급 장치가 제공할 수 있는 것 보다 더 많은 전력을 필요 로 합니다.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 수정 조치 E1711 PCI parity error on Bus ## Device ## Function ## PCI 구성 공간 (버스 ##, 장치 ##, 기능 ##) 에 상 주한 구성요소의 PCI 패 리티 오류가 시스템 BIOS 에 보고되었습니다. PCIe 확장 카드를 분리 하고 다시 장착합니다. 문제가 지속되면 153페 이지의 "확장 카드 문제 해결"을 참조하십시오. PCI parity error on Slot #. Review & clear SEL. 지정된 슬롯에 상주한 구 성요소의 PCI 패리티 오 류가 시스템 BIOS에 보고 되었습니다. PCIe 확장 카드를 분리 하고 다시 장착합니다. 문제가 지속되면 153페 이지의 "확장 카드 문제 해결"을 참조하십시오.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 E1920 iDRAC6 Upgrade 선택 사양인 iDRAC6의 Failed. 업그레이드가 실패했습 니다. 원인 수정 조치 E1A14 SAS cable A SAS 케이블 A가 연결되 케이블을 다시 연결합니 failure. Check 지 않았거나 불량 상태입 다. 문제가 지속되면 케 connection. 니다. 이블을 교체합니다. 163페이지의 "도움말 얻 기"를 참조하십시오. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E1A15 SAS cable B SAS 케이블 B가 연결되지 케이블을 다시 연결합니 failure. Check 않았거나 불량 상태입니다. 다. 문제가 지속되면 케 connection. 이블을 교체합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E1A1D Control panel USB cable not detected. Check cable.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 E2013 BIOS unable to 시스템 BIOS가 해당 플래 147페이지의 "시스템 메 shadow memory. 시 이미지를 메모리에 복 모리 문제 해결"을 참조 Check DIMMs. 사하는 데 실패했습니다. 하십시오. 원인 수정 조치 E2014 CMOS RAM CMOS 오류입니다. 10초 동안 시스템에서 failure. Power CMOS RAM이 올바르게 AC 전원을 분리하고 시 cycle AC. 작동하지 않습니다. 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E2015 DMA Controller DMA 컨트롤러 오류입 failure. Power 니다. cycle AC. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 수정 조치 E2019 Parity error. Power cycle AC. 패리티 오류입니다. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E201A SuperIO SIO 오류입니다. failure. Power cycle AC. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. 키보드 컨트롤러 오류입 10초 동안 시스템에서 니다. AC 전원을 분리한 다음 시스템을 재시작합니다. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E201B Keyboard Controller error. Power cycle AC.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 E201E POST memory test failure. Check DIMMs. 수정 조치 BIOS POST 메모리 검사 147페이지의 "시스템 메 오류입니다. 모리 문제 해결"을 참조 하십시오. 문제가 지속되면 163페 이지의 "도움말 얻기"를 참조하십시오. E2020 CPU 프로세서 구성 오류입니다. configuration failure. Check screen message. 화면에 특정 오류 메시지 가 있는지 확인합니다. 154페이지의 "프로세서 문제 해결"을 참조하십 시오. E2021 Incorrect 잘못된 메모리 구성입니다. memory configuration. Review User Guide. 화면에 특정 오류 메시지 가 있는지 확인합니다. 147페이지의 "시스템 메 모리 문제 해결"을 참조 하십시오.
표 1-2. LCD 상태 메시지 (선택 사양) (계속) 코드 텍스트 원인 수정 조치 I1911 LCD Log Full. Check SEL to review all Errors. LCD 오버플로 메시지입 니다. 최대 10개의 오류 메시지가 LCD에 순차적 으로 표시될 수 있습니다. 11번째 메시지는 SEL에 서 이벤트에 대한 자세한 내용을 확인할 것을 지시 합니다. 이벤트에 대한 자세한 내용은 SEL을 참조하십 시오. 10초 동안 시스템에서 AC 전원을 분리하고 시 스템을 재시작합니다. I1912 SEL full. SEL이 이벤트로 꽉 차서 더 SEL에서 이벤트에 대한 Review & clear 이상 기록할 수 없습니다. 자세한 내용을 확인한 다 log. 음 SEL을 지웁니다. I1920 iDRAC6 Upgrade 선택 사양인 iDRAC6이 Successful. 성공적으로 업그레이드 되었습니다. W1228 RAID Controller battery capacity < 24hr.
LCD 상태 메시지에 설명된 문제 해결 (선택 사양) LCD의 코드 및 텍스트는 일반적으로 쉽게 수정할 수 있는 정확한 오류 상 태를 지정할 수 있습니다. 예를 들어 코드 E1418 CPU_1_Presence가 나 타나면 마이크로프로세서가 소켓 1에 설치되지 않은 것입니다. 반대로, 연관된 여러 개의 오류가 발생하면 문제를 확인할 수 있습니다. 예 를 들면, 다중 전압 오류를 표시하는 여러 개의 메시지가 표시될 경우 전원 공급 실패가 문제의 원인임을 확인할 수 있습니다. LCD 상태 메시지 제거 (선택 사양) 센서와 관련된 오류 (예: 온도, 전압, 팬 등) 일 경우 센서가 정상 상태로 회 복되면 LCD 메시지는 자동으로 제거됩니다. 예를 들면, 구성요소의 온도 가 적당한 범위를 벗어나면 LCD는 오류를 표시하고 온도가 적당한 범위 내로 회복되면 메시지는 LCD에서 제거됩니다. 다른 오류일 경우 메시지 를 디스플레이에서 제거하기 위한 작업을 수행해야 합니다.
시스템 메시지 시스템 메시지가 화면에 표시되어 시스템의 발생 가능한 문제를 알려줍니다. 주: 다음 표에 나열되지 않은 시스템 메시지를 받은 경우, 메시지가 나타날 때 실행 중인 응용프로그램의 설명서나 운영 체제 설명서에서 해당 메시지에 대 한 설명 및 권장되는 조치를 확인하십시오. 표 1-3. 시스템 메시지 메시지 원인 수정 조치 Alert! iDRAC6 not 선택 사양인 iDRAC6이 올 시스템이 다시 부팅될 때까 responding. 바르게 작동하지 않거나 초 지 기다립니다. Rebooting. 기화를 완료하지 않았기 때 문에 BIOS와의 통신에 응답 하지 않고 있습니다. 시스템 이 다시 부팅됩니다. Alert! iDRAC6 not responding. Power required may exceed PSU wattage. 선택 사양인 iDRAC6이 중 지되었습니다. 10초 동안 시스템에서 AC 전원을 분리하고 시스템을 재시작합니다.
표 1-3. 시스템 메시지 (계속) 메시지 원인 수정 조치 Alert! Power required exceeds PSU wattage. Check PSU and system configuration. 전원 공급 장치에서 프로세 서, 메모리 모듈 및 확장 카 드의 시스템 구성을 지원하 지 않을 수 있습니다. 시스템 구성요소를 업그레 이드한 경우 시스템을 이전 구성으로 되돌리십시오. 시 스템이 이 경고 없이 부팅되 는 경우 교체된 구성요소가 이 전원 공급 장치에서 지원 되지 않습니다. Energy Smart 전원 공급 장치가 설 치된 경우에는 이를 고출력 전원 공급 장치로 교체한 후 구성요소를 사용합니다. 122페이지의 "전원 공급 장 치"를 참조하십시오. Alert! Continuing system boot accepts the risk that system may power down without warning.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Caution! NVRAM_CLR 점퍼가 지우기 NVRAM_CLR jumper 설정으로 설치되어 있습니다. is installed on CMOS가 지워졌습니다. system board. Please run SETUP. 수정 조치 NVRAM_CLR 점퍼를 기본 위치 (3번 핀과 5번 핀) 로 옮깁니다. 점퍼 위치에 대한 내용은 그림 6-1을 참조하 십시오. 시스템을 재시작하 여 BIOS 설정을 다시 시작 합니다. 53페이지의 "시스 템 설치 프로그램 및 UEFI 부팅 관리자 사용"을 참조 하십시오. CPU set to minimum frequency. 절전을 위해 의도적으로 프 의도적인 설정이 아니라면 로세서 속도를 낮게 설정했 다른 시스템 메시지를 확인 하여 가능한 원인을 찾아봅 을 수 있습니다. 니다. Current boot mode is set to UEFI.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Error 8602 Auxiliary Device Failure. Verify that mouse and keyboard are securely attached to correct connectors. 수정 조치 마우스 또는 키보드 케이블 마우스 또는 키보드 케이블 이 느슨하거나 잘못 연결되 을 다시 장착합니다. 었습니다. 마우스 또는 키보드에 결함 마우스 또는 키보드가 잘 작 이 있습니다. 동하는지 확인합니다. 140 페이지의 "USB 장치 문제 해결"을 참조하십시오. Gate A20 failure. 키보드 컨트롤러 및 시스템 163페이지의 "도움말 얻기" 를 참조하십시오. 보드에 오류가 있습니다. Invalid configuration information please run SETUP program. 잘못된 시스템 구성으로 인해 시스템 설치 프로그램을 실 시스템이 정지되었습니다. 행하여 현재의 설정을 검토 합니다.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Manufacturing mode detected. 수정 조치 시스템이 제조 모드에 있습 시스템이 제조 모드에서 벗 니다. 어나게 하려면 다시 부팅합 니다. Maximum rank count exceeded. The following DIMM has been disabled: x. 잘못된 메모리 구성입니다. 시스템은 실행되지만 지정 된 메모리 모듈은 비활성화 됩니다. 메모리 모듈이 올바른 구성 으로 설치되어 있는지 확인 합니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하십시오. Memory Initialization Warning: Memory size may be reduced. 잘못된 메모리 구성입니다. 시스템은 실행되지만 사용 할 수 있는 물리적인 메모리 양보다 적은 메모리 양으로 실행됩니다. 메모리 모듈이 올바른 구성 으로 설치되어 있는지 확인 합니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하십시오.
표 1-3. 시스템 메시지 (계속) 메시지 원인 수정 조치 No boot device available. 광학 드라이브 하위 시스템, 하드 드라이브 또는 하드 드 라이브 하위 시스템에 결함 이 있거나 설치되지 않았거 나 부팅 USB 키가 설치되어 있지 않습니다. 부팅 USB 키, 광학 드라이 브 또는 하드 드라이브를 사 용합니다. 문제가 지속되면 150페이지의 "광학 드라이 브 문제 해결", 140페이지의 "USB 장치 문제 해결", 149 페이지의 "내부 USB 키 문 제 해결" 및 152페이지의 " 하드 드라이브 문제 해결" 을 참조하십시오. 부팅 장치 의 순서 설정에 대한 자세한 내용은 53페이지의 "시스템 설치 프로그램 및 UEFI 부 팅 관리자 사용"을 참조하 십시오. No boot sector on 시스템 설치 프로그램에 잘 hard drive. 못된 구성 설정이 있거나 하 드 드라이브에 운영 체제가 없습니다. 시스템 설치 프로그램의 하 드 드라이브 구성 설정을 확 인합니다.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Plug & Play Configuration Error. PCIe 장치를 초기화하는 데 NVRAM_CLR 점퍼를 지우 오류가 발생했습니다. 시스 기 위치 (1번 핀과 3번 핀) 템 보드에 오류가 있습니다. 로 설치한 후 시스템을 다시 부팅합니다. 점퍼 위치에 대 한 내용은 그림 6-1을 참조 하십시오. 문제가 지속되면 153페이지의 "확장 카드 문 제 해결"를 참조하십시오. Quad rank DIMM 잘못된 메모리 구성입니다. detected after single rank or dual rank DIMM in socket. Read fault. Requested sector not found. SATA Port x drive not found. 44 시스템 정보 운영 체제에서 하드 드라이 브, 광학 드라이브 또는 USB 장치를 읽을 수 없습니다. 운 영 체제에서 디스크의 특정 섹터를 찾을 수 없거나 요청 된 섹터에 결함이 있습니다.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Sector not found. 하드 드라이브, USB 장치 또 는 USB 매체에 오류가 있습 Seek error. 니다. Seek operation failed. Shutdown failure. 일반 시스템 오류입니다. 수정 조치 USB 매체 또는 장치를 교체 합니다. USB 또는 SAS 후면 판 케이블이 올바르게 연결 되었는지 확인합니다. 시스 템에 설치된 적절한 드라이 브에 대한 내용은 140페이 지의 "USB 장치 문제 해결" 또는 152페이지의 "하드 드 라이브 문제 해결"을 참조 하십시오. 163페이지의 "도움말 얻기" 를 참조하십시오. The amount of 메모리가 추가 또는 분리되 메모리를 추가 또는 분리한 system memory has 었거나 메모리 모듈에 오류 경우 이 메시지는 정보 제공 changed. 가 있을 수 있습니다. 용이며 무시할 수 있습니다.
표 1-3. 시스템 메시지 (계속) 메시지 원인 수정 조치 The following DIMMs should match in 잘못된 메모리 구성입니다. 지정된 메모리 모듈의 크기, 등급 수, 데이터 레인 수 등 이 일치하지 않습니다. 메모리 모듈이 올바른 구성 으로 설치되어 있는지 확인 합니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하십시오. geometry: x,x,... The following DIMMs should match in rank count: x,x,... The following DIMMs should match in size: x,x,... The following DIMMs should match in size and geometry: x,x,... The following DIMMs should match in size and rank count: x,x,... Thermal sensor not detected on x.
표 1-3. 시스템 메시지 (계속) 메시지 원인 수정 조치 Timer chip 시스템 보드에 오류가 있습 163페이지의 "도움말 얻기" counter 2 failed. 니다. 를 참조하십시오. TPM configuration operation honored. System will now reset. TPM 구성 명령어가 입력되었 참조용으로만 제공됩니다. 습니다. 시스템이 다시 부팅된 후 명령어가 실행됩니다. TPM configuration operation is pending. Press (I) to Ignore OR (M) to Modify to allow this change and reset the system. 이 메시지는 TPM 구성 명령 계속하려면 I 또는 M을 입 어를 입력한 후 시스템이 재 력합니다. 시작하는 동안 표시됩니다. 계속하려면 사용자 개입이 필요합니다. WARNING: Modifying could prevent security. TPM failure.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Unexpected interrupt in protected mode. 메모리 모듈이 잘못 장착되 메모리 모듈을 다시 장착합 었거나 키보드/마우스 컨트 니다. 147페이지의 "시스템 롤러 칩에 결함이 있습니다. 메모리 문제 해결"을 참조 하십시오. 문제가 지속되면 163페이지의 "도움말 얻기" 를 참조하십시오. Unsupported CPU combination. 시스템이 프로세서를 지원 하지 않습니다. 지원되는 프로세서를 설치 합니다. 117페이지의 "프로 세서"를 참조하십시오. Unsupported DIMM detected. The following DIMM has been disabled: x. 잘못된 메모리 구성입니다. 시스템은 실행되지만 지정 된 메모리 모듈은 비활성화 됩니다. 메모리 모듈이 올바른 구성 으로 설치되어 있는지 확인 합니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하십시오.
표 1-3. 시스템 메시지 (계속) 메시지 원인 수정 조치 Warning! No micro 마이크로 코드 업데이트가 code update 실패했습니다. loaded for processor n. BIOS 펌웨어를 업데이트합 니다. 163페이지의 "도움말 얻기"를 참조하십시오. 전원 공급 장치에서 프로세 서, 메모리 모듈 및 확장 카 드의 시스템 구성을 지원하 지 않을 수 있습니다. 시스템 구성요소가 업그레 이드되었을 뿐이라면 시스 템을 이전의 구성으로 되돌 립니다. 시스템이 이러한 경 고 없이 부팅되면 전원 공급 장치에서 지원하지 않는 구 성요소를 교체합니다. Energy Smart 전원 공급 장 치가 설치된 경우에는 이를 고출력 전원 공급 장치로 교 체한 후 구성요소를 사용합 니다. 122페이지의 "전원 공 급 장치"를 참조하십시오. Warning! Power required exceeds PSU wattage. Check PSU and system configuration.
표 1-3. 시스템 메시지 (계속) 메시지 원인 Warning! Unsupported memory configuration detected. The memory configuration is not optimal. The recommended memory configuration is: . 잘못된 메모리 구성입니다. 메모리 모듈이 올바른 구성 시스템은 실행되지만 기능 으로 설치되어 있는지 확인 이 감소됩니다. 합니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하십시오. 문제가 지속 되면 147페이지의 "시스템 메모리 문제 해결"을 참조 하십시오. Write fault. USB 장치, USB 매체, 광학 드 라이브 조립품, 하드 드라이브 또는 하드 드라이브 하위 시스 템에 결함이 있습니다. Write fault on selected drive. 수정 조치 USB 매체 또는 장치를 교체 합니다.
경고 메시지 경고 메시지는 가능한 문제를 경고하고 시스템이 작업을 계속하기 전에 응 답할 것을 요청하는 메시지를 표시합니다. 예를 들면, 디스켓을 포맷하기 전에 디스켓에 있는 모든 데이터가 유실될 수 있음을 경고하는 메시지가 표시됩니다. 경고 메시지는 일반적으로 작업을 중단하며 y (예) 또는 n (아니오) 을 입력하여 응답할 것을 요청합니다. 주: 경고 메시지는 응용프로그램 또는 운영 체제에서 생성됩니다. 자세한 내 용은 운영 체제 또는 응용프로그램과 함께 제공된 설명서를 참조하십시오. 진단 메시지 시스템에 대해 진단 검사를 실행하면 시스템 진단 유틸리티가 메시지를 생 성할 수 있습니다. 시스템 진단 프로그램에 대한 자세한 내용은 156페이지 의 "내장형 시스템 진단 프로그램 실행"을 참조하십시오. 경고 메시지 시스템 관리 소프트웨어는 해당 시스템에 대한 경고 메시지를 생성합니다. 경고 메시지에는 드라이브, 온도, 팬 및 전원 상태에 대한 정보, 상태, 경고 및 오류 메시지가 포함됩니다.
시스템 정보
시스템 설치 프로그램 및 UEFI 부 팅 관리자 사용 시스템 설치 프로그램은 시스템 하드웨어를 관리하고 BIOS 수준 옵션을 지정할 수 있는 BIOS 프로그램입니다. 시스템 설치 프로그램을 사용하여 다음을 수행할 수 있습니다. • 하드웨어를 추가 또는 제거한 후 NVRAM 설정 변경 • 시스템 하드웨어 구성 확인 • 내장형 장치 활성화 또는 비활성화 • 성능 및 전원 관리 임계값 설정 • 시스템 보안 관리 시스템 부팅 모드 선택 시스템 설치 프로그램을 사용하면 운영 체제를 설치하는 경우의 부팅 모드 를 지정할 수도 있습니다. • 기본값인 BIOS 부팅 모드는 표준 BIOS 수준 부팅 인터페이스입니다. • UEFI 부팅 모드는 시스템 BIOS를 은폐하는 UEFI (Unified Extensible Firmware Interface) 사양에 기반하는 확장된 64비트 부팅 인터페이스입 니다. 이 인터페이스에 대한 자세한 내용은 66페이지의 "UEFI 부팅 관 리자 시작"을 참조하십시오.
시스템 설치 프로그램 시작 1 시스템을 켜거나 재시작합니다. 2 다음과 같은 메시지가 나타나면 즉시 키를 누릅니다. = 시스템 설치 키를 누르기 전에 운영 체제가 로드되기 시작하면 시스템이 부팅 을 완료하게 한 다음 시스템을 재시작하고 다시 시도합니다. 오류 메시지에 응답 시스템이 부팅되는 동안 오류 메시지가 나타날 경우 메시지 내용을 기록합 니다. 메시지에 대한 설명이나 오류 수정 조치 사항은 38페이지의 "시스템 메시지"를 참조하십시오. 주: 메모리 업그레이드를 설치한 후, 시스템을 처음 시작하면 메시지가 표시 되는데 이는 정상적인 동작입니다. 시스템 설치 프로그램 탐색 키 사용 키 작동 위쪽 화살표 키 또는 키 조합 이전 필드로 이동합니다. 아래쪽 화살표 키 또는 키 다음 필드로 이동합니다. 키, 스페이스바, <+> 키, <–> 키, 왼쪽 및 오른쪽 화살표 키 필드의 여러 설정 사이에서 이동합니다.
시스템 설치 프로그램 옵션 기본 화면 주: 시스템 설치 프로그램의 옵션은 시스템 구성에 따라 변경됩니다. 주: 시스템 설치 프로그램 기본값은 다음 항목의 각 해당 옵션 아래에 표시됩 니다. 옵션 설명 System Time (시스템 시간) 시스템의 내부 클럭 시간을 설정합니다. System Date (시스템 날짜) 시스템의 내부 달력 날짜를 설정합니다. Memory Settings (메모리 설정) 설치된 메모리와 관련된 정보를 표시합니다. 57페이 지의 "Memory Settings (메모리 설정) 화면"을 참조하 십시오. Processor Settings (프로세서 설정) 프로세서와 관련된 정보 (속도, 캐시 크기 등) 를 표시 합니다. 58페이지의 "Processor Settings (프로세서 설 정) 화면"을 참조하십시오.
옵션 설명 SATA Settings (SATA 설정) 내장형 SATA 컨트롤러 및 포트를 활성화하거나 비활 성화하는 화면을 표시합니다. 59페이지의 "SATA Settings (SATA 설정) 화면"을 참조하십시오. Boot Settings (부팅 설정) 부팅 모드 (BIOS 또는 UEFI) 를 지정하는 화면을 표 시합니다. BIOS 부팅 모드의 경우 부팅 장치를 지정 할 수도 있습니다. 59페이지의 "Boot Settings (부팅 설 정) 화면"을 참조하십시오. Integrated Devices (내장형 장치) 내장형 장치 컨트롤러 및 포트를 활성화하거나 비활 성화하고 관련 기능 및 옵션을 지정하는 화면을 표시 합니다. 60페이지의 "Integrated Devices (내장형 장치) 화면"을 참조하십시오. PCI IRQ Assignment (PCI IRQ 할당) PCI 버스의 각 내장형 장치와 IRQ가 필요한 설치된 모든 확장 카드에 할당된 IRQ를 변경하는 화면을 표 시합니다.
옵션 설명 Report Keyboard Errors (키보드 오류 보고) (기본값: Report (보고)) POST 동안 키보드 오류 보고를 활성화하거나 비활성 화합니다. 키보드가 연결된 호스트 시스템의 경우 Report (보고) 를 선택합니다. POST 동안 키보드 또는 키보드 컨트롤러와 관련된 모든 오류 메시지를 표시 하지 않으려면 Do Not Report (보고 안 함) 를 선택합 니다. 키보드가 시스템에 장착되어 있는 경우 이러한 설정은 키보드 자체의 작동에 영향을 주지 않습니다. F1/F2 Prompt on Error POST 동안 오류가 발생하면 시스템이 정지되도록 설 (오류 시 F1/F2 프롬프트) 정합니다. 이렇게 하면 정상적인 POST 동안 빠르게 (기본값: Enabled (활성화)) 스크롤되어 발견하기 어려운 이벤트를 살펴볼 수 있 습니다. 키를 눌러서 계속하거나 키를 눌러서 시스템 설치 프로그램을 시작할 수 있습니다.
Processor Settings (프로세서 설정) 화면 옵션 설명 64-bit (64비트) 프로세서에서 64비트 확장을 지원할지 여부를 지정합 니다. Core Speed (코어 속도) 프로세서 클럭 속도를 표시합니다. Bus Speed (버스 속도) 프로세서 버스 속도를 표시합니다. Logical Processor (논리 프로세서) (기본값: Enabled (활성화)) SMT (Simultaneous Multi-Threading) 기술을 지원하는 프로세서에서 각 프로세서 코어는 최대 두 개의 논리 프로세서를 지원합니다. 이 필드가 Enabled (활성화) 로 설정된 경우 BIOS에서는 두 논리 프로세서를 모두 보고합니다. Disabled (비활성화) 로 설정된 경우에는 BIOS에서 하나의 논리 프로세서만 모니터링합니다.
SATA Settings (SATA 설정) 화면 옵션 설명 SATA Controller (SATA 컨트롤러) (기본값: ATA) 내장형 SATA를 Off (끄기), ATA 또는 RAID 모드로 설 정할 수 있습니다. 주: SATA를 RAID 모드로 설정하면 UEFI 지원이 비활성 화됩니다. Port A (포트 A) (기본값: Auto (자동)) Auto (자동) 로 설정하면 SATA 포트 A에 연결된 장치에 대한 BIOS 지원이 활성화됩니다. Off (끄기) 로 설정하 면 장치에 대한 BIOS 지원이 비활성화됩니다. Port B (포트 B) (기본값: Off (끄기)) Auto (자동) 로 설정하면 SATA 포트 B에 연결된 장치에 대한 BIOS 지원이 활성화됩니다. Off (끄기) 로 설정하 면 장치에 대한 BIOS 지원이 비활성화됩니다.
옵션 설명 Boot Sequence (부팅 순서) Boot Mode (부팅 모드) 를 BIOS로 설정한 경우 이 필 드는 시스템 시작에 필요한 운영 체제 파일의 위치를 시스템에 제공합니다. Boot Mode (부팅 모드) 를 UEFI 로 설정한 경우 시스템을 다시 부팅하고 화면의 메시지 에 따라 키를 눌러 UEFI 부팅 관리자 유틸리티 에 액세스할 수 있습니다. Boot Sequence Retry (부팅 순서 재시도) (기본값: Disabled (비활성화)) 이 필드가 활성화된 시스템이 부팅에 실패하는 경우 시 스템은 30초 후에 부팅을 다시 시도합니다. Integrated Devices (내장형 장치) 화면 옵션 설명 User Accessible USB ports (사용자 액세 스 가능 USB 포트) (기본값: All Ports On (모든 포트 켜기)) 사용자가 액세스할 수 있는 USB 포트를 활성화하거나 비활성화합니다.
옵션 설명 MAC Address (MAC 주소) NIC의 MAC 주소를 표시합니다. OS Watchdog Timer (OS Watchdog 타이머) (기본값: Disabled (비활성화)) 운영 체제의 작동을 모니터링하도록 타이머를 설정하 고 시스템이 응답을 멈추는 경우 복구를 지원합니다. Enabled (활성화) 로 설정하면 운영 체제에서 타이머를 초기화할 수 있습니다. Disabled (비활성화) 로 설정하 면 타이머가 초기화되지 않습니다. 주: 이 기능은 ACPI (고급 구성 및 전원 인터페이스) 3.0b 사양의 WDAT 구현을 지원하는 운영 체제에서만 사용할 수 있습니다. Embedded Video Controller (내장형 비디 오 컨트롤러) (기본값: Enabled (활성화)) 내장형 비디오 컨트롤러에 대한 BIOS 지원을 활성화하 거나 비활성화합니다. 주: 이 필드는 추가 비디오 카드가 설치된 경우에만 비 활성화할 수 있습니다.
Serial Communication (직렬 통신) 화면 옵션 설명 Serial Communication (직렬 통신) (기본값: On without Console Redirection (콘솔 재지정 없이 켜기)) 직렬 통신 장치 (Serial Device 1 (직렬 장치 1) 및 Serial Device 2 (직렬 장치 2)) 가 BIOS에서 활성화될지 여부 를 선택합니다. BIOS 콘솔 재지정을 활성화하고 사용 되는 포트 주소를 지정할 수도 있습니다. Serial Port Address (직렬 포트 주소) (기본값: Serial Device 1 (직렬 장치 1) =COM1, Serial Device2 (직렬 장치 2) =COM2) 두 직렬 장치의 직렬 포트 주소를 설정합니다.
Power Management (전원 관리) 화면 옵션 설명 Power Management (전원 관리) (기본값: Active Power Controller (활성 전원 컨 트롤러)) 옵션으로는 OS Control (OS 제어), Active Power Controller (활성 전원 컨트롤러), Custom (사용자 정의), Maximum Performance (최대 성능) 가 있습니다. BIOS에 서는 Custom (사용자 정의) 설정을 제외한 나머지 모든 설 정에 대해 이 화면의 전원 설정을 다음과 같이 미리 구성 합니다. • OS Control (OS 제어) 의 경우 CPU 전원은 OS DBPM으로, 팬 전원은 Minimum Power (최소 전원) 로, 메모리 전원은 Maximum Performance (최대 성능) 로 설정됩니다. 이 설정에서 모든 프로세서 성능 정보 는 제어를 위해 시스템 BIOS에서 운영 체제로 전달됩 니다.
System Security (시스템 보안) 화면 옵션 설명 System Password (시스템 암호) 암호 보안 기능의 현재 상태를 표시하고 새 시스템 암호 를 할당 및 확인하도록 합니다. 주: 자세한 내용은 69페이지의 "시스템 암호 사용"을 참 조하십시오. Setup Password (설치 암호) 설치 암호를 사용하여 시스템 설치 프로그램에 대한 액 세스를 제한합니다. 주: 자세한 내용은 71페이지의 "설치 암호 사용"을 참조 하십시오. Password Status (암호 상태) (기본값: Unlocked (잠금 해제)) Setup Password (설치 암호) 가 할당되어 있고 이 필드가 Locked (잠금) 로 설정된 경우 시스템 시작 시 시스템 암호를 변경하거나 비활성화할 수 없습니다. TPM Security (TPM 보안) (기본값: Off (끄기)) 시스템에서 신뢰할 수 있는 플랫폼 모듈 (TPM) 보고를 설정합니다.
옵션 설명 주의: TPM을 지우면 TPM의 모든 암호화 키가 손 실됩니다. 이 옵션은 운영 체제로 부팅하는 것을 방지하므로 암호화 키를 복원할 수 없는 경우 데이 터가 손실됩니다. 이 옵션을 활성화하기 전에 TPM 키를 백업합니다. TPM Clear (TPM 지우기) (기본값: No (아니오)) Yes (예) 로 설정하는 경우 모든 TPM 내용이 지워집니다. 주: TPM Security (TPM 보안) 를 Off (끄기) 로 설정하는 경 우 이 필드는 읽기 전용입니다. Power Button (전원 단추) Enabled (활성화) 로 설정하는 경우 전원 단추로 시스 (기본값: Enabled 템 전원을 켜거나 끌 수 있습니다. ACPI를 지원하는 운 영 체제의 경우 전원이 꺼지기 전에 순서대로 종료를 수 (활성화)) 행합니다. Disabled (비활성화) 로 설정하는 경우 전원 단추로 시 스템 전원을 켜는 동작만 할 수 있습니다.
Exit (종료) 화면 시스템 설치 프로그램을 종료하려면 키를 누릅니다. 그러면 Exit (종료) 화면이 나타납니다. • Save Changes and Exit (변경 사항 저장 및 종료) • Discard Changes and Exit (변경 사항 취소 및 종료) • Return to Setup (설치 프로그램으로 돌아가기) UEFI 부팅 관리자 시작 주: UEFI 부팅 모드에서 운영 체제를 설치하려면 해당 운영 체제가 64비트 UEFI 호환 운영 체제 (예: Microsoft® Windows Server® 2008 x64 버전) 여야 합니 다. DOS 및 32비트 운영 체제는 BIOS 부팅 모드에서만 설치할 수 있습니다. 주: UEFI 부팅 관리자에 액세스하려면 시스템 설치 프로그램에서 부팅 모드가 UEFI로 설정되어야 합니다. UEFI 부팅 관리자를 사용하면 다음 작업을 수행할 수 있습니다.
UEFI 부팅 관리자 탐색 키 사용 키 작동 위쪽 화살표 이전 필드로 이동하여 해당 필드를 강조 표시합 니다. 아래쪽 화살표 다음 필드로 이동하여 해당 필드를 강조 표시합 니다. 스페이스바, 키, <+> 키, <–> 키 필드의 여러 설정 사이에서 이동합니다. UEFI 부팅 관리자 화면을 새로 고치거나 다른 프 로그램 화면에서 UEFI 부팅 관리자 화면으로 돌 아갑니다. UEFI 부팅 관리자 도움말 파일을 표시합니다. UEFI Boot Manager (UEFI 부팅 관리자) 화면 옵션 설명 Continue (계속) 시스템에서는 먼저 부팅 순서의 첫 번째 항목에 해당 하는 장치로 부팅을 시도합니다. 부팅 시도가 실패하 면 부팅 순서의 다음 항목에 해당하는 장치로 부팅을 계속 시도합니다. 이러한 부팅 시도는 부팅에 성공하 거나 시도할 부팅 옵션이 더 이상 없을 때까지 계속됩 니다.
UEFI Boot Settings (UEFI 부팅 설정) 화면 옵션 설명 Add Boot Option (부팅 옵션 추가) 새 부팅 옵션을 추가합니다. Delete Boot Option (부팅 옵션 삭제) 기존 부팅 옵션을 삭제합니다. Enable/Disable Boot Option 부팅 옵션 목록에서 부팅 옵션을 활성화하거나 비활성 (부팅 옵션 활성화/ 화합니다. 비활성화) Change Boot Order (부팅 순서 변경) 부팅 옵션 목록에서 순서를 변경합니다. One-Time Boot From File (파일에서 원타임 부팅) 부팅 옵션 목록에 포함되지 않은 원타임 부팅 옵션을 설정합니다. System Utilities (시스템 유틸리티) 화면 옵션 설명 System Setup (시스템 설치 프로그램) 다시 부팅 없이 시스템 설치 프로그램에 액세스합니다.
시스템 및 설치 암호 기능 주: 잊어버린 암호의 처리 방법은 162페이지의 "잊어버린 암호 비활성화"를 참 조하십시오. 본 시스템은 시스템 암호 기능이 활성화되지 않은 상태로 제공됩니다. 시스 템 암호 보호를 활성화한 상태로만 시스템을 작동하십시오. 주의: 암호 기능은 시스템 데이터에 대한 기본적인 수준의 보안을 제공합니다. 주의: 실행 중인 시스템을 그대로 두고 자리를 비우는 경우 누구나 시스템에 저장된 데이터에 액세스할 수 있습니다. 시스템 암호 사용 시스템 암호가 할당된 경우 시스템 시작 이후 시스템 암호를 입력하라는 메시지가 나타나며 해당 암호를 가진 사용자만 시스템을 제한 없이 사용할 수 있습니다. 시스템 암호 할당 시스템 암호를 할당하기 전에 먼저 시스템 설치 프로그램을 시작하여 System Password (시스템 암호) 옵션을 확인합니다. 시스템 암호가 할당되어 있으면 System Password (시스템 암호) 가 Enabled (활성화) 로 설정된 것입니다.
암호는 대소문자를 구분하지 않고 할당됩니다. 일부 키 조합은 유효하 지 않습니다. 유효하지 않은 키 조합을 입력하면 시스템에서 경고음이 발생합니다. 입력한 문자를 지우려면 키 또는 왼쪽 화살 표 키를 누릅니다. 주: 시스템 암호를 할당하지 않고 필드에서 나오려면 키를 눌러 다른 필드로 이동하거나 5단계를 완료하기 전에 키를 누릅니다. 4 키를 누릅니다. 5 암호를 확인하려면 암호를 다시 입력하고 키를 누릅니다. System Password (시스템 암호) 의 설정이 Enabled (활성화) 로 변경됩 니다. 시스템 설치 프로그램을 종료하고 시스템을 사용합니다. 6 암호 보호 기능이 적용되도록 지금 시스템을 다시 부팅하거나 작업을 계속 진행합니다. 주: 암호 보호 기능은 시스템을 다시 부팅해야만 적용됩니다.
시스템을 종료하고 재시작한 후에도 올바른 암호를 입력할 때까지 이 오류 메시지가 계속 표시됩니다. 주: 시스템이 무단으로 변경되는 것을 방지하려면 System Password (시스템 암호) 및 Setup Password (설치 암호) 옵션과 함께 Password Status (암호 상태) 옵션을 사용할 수 있습니다. 기존 시스템 암호 삭제 또는 변경 1 시스템 설치 프로그램을 시작하고 System Security (시스템 보안) 를 선택합니다. 2 Setup Password (설치 암호) 를 강조 표시하고 키를 눌러 설 치 암호 창에 액세스합니다. 키를 두 번 눌러 기존의 설치 암 호를 지우십시오. 3 설정이 Not Enabled (활성화되지 않음) 로 변경됩니다. 4 설치 암호를 새로 할당하려면 71페이지의 "설치 암호 할당"에 설명된 절차를 수행하십시오.
활성화된 설치 암호를 사용하여 시스템 작동 Setup Password (설치 암호) 를 Enabled (활성화) 로 설정한 경우 시스템 설치 프로그램의 옵션을 변경하기 전에 설치 암호를 정확하게 입력해야 합니다. 잘못된 암호를 계속하여 세 번 이상 입력할 경우 시스템 설치 프로그램 화 면을 볼 수는 있으나 변경할 수 없습니다. System Password (시스템 암호) 설정이 Enabled (활성화) 가 아니고 시스템 암호가 Password Status (암호 상태) 옵션을 통해 잠기지 않은 경우에는 예외적으로 시스템 암호를 할당 할 수 있습니다. 그러나 이 경우에도 기존의 시스템 암호를 변경하거나 비 활성화할 수는 없습니다. 주: 시스템 암호가 무단으로 변경되지 않도록 하려면 Setup Password (설치 암 호) 옵션과 Password Status (암호 상태) 옵션을 결합하여 사용할 수 있습니다.
선택 사양인 iDRAC6 Express 카드가 설치된 경우 Unified Server Configurator는 다음과 같은 추가 기능을 제공합니다. • 펌웨어 업데이트 다운로드 및 적용 • 하드웨어 및 펌웨어 구성 Unified Server Configurator 설정, 하드웨어 및 펌웨어 구성, 운영 체제 배포 등에 대한 자세한 내용은 Dell 지원 웹 사이트 (support.dell.com/manuals) 에서 Unified Server Configurator 설명서를 참조하십시오. 베이스보드 관리 컨트롤러 구성 BMC를 사용하여 시스템의 구성, 모니터링 및 복구를 원격으로 수행할 수 있습니다. BMC는 다음 기능을 제공합니다.
iDRAC 구성 유틸리티 iDRAC 구성 유틸리티는 사전 부팅 구성 환경으로 사용자는 이를 통해 iDRAC6 및 관리되는 서버에 대한 매개변수를 확인하고 설정할 수 있습니다. iDRAC 구성 유틸리티는 다음 기능을 제공합니다. • 오류 로깅 및 SNMP 경고 활성화. • 시스템 이벤트 로그 및 센서 상태에 대한 액세스 제공. • 전원 켜기 및 끄기를 포함하는 시스템 기능 제어. • 시스템의 전원 상태 또는 시스템의 운영 체제에 관계없이 독립적으로 작동. • 시스템 설치, 텍스트 기반 유틸리티, 운영 체제 콘솔에 대한 텍스트 콘솔 재지정 제공. iDRAC 구성 유틸리티는 이외에 다음과 같은 추가 기능도 제공합니다. • 전용 iDRAC6 Enterprise 카드 포트 또는 내장형 NIC1을 통해 iDRAC6 LAN (Local Area Network) 구성, 활성화 또는 비활성화. • IPMI over LAN 활성화 또는 비활성화.
시스템 구성요소 설치 경고: 시스템을 이동 또는 전송하는 동안은 시스템과 함께 제공된 포장재를 사용하고, 충격이나 진동으로 인한 손상을 방지할 수 있게 충분히 주의를 기 울이는 것이 좋습니다. 주: 구성에 따라 시스템에 케이블 또는 핫 스왑 가능한 하드 드라이브, 중복 또 는 비중복 전원 공급 장치 및 LCD 패널 또는 진단 표시등이 있을 수 있습니다. 이 항목의 그림에서는 핫 스왑 가능 하드 드라이브 및 LCD 패널을 사용하는 시 스템을 보여 줍니다. 권장 도구 • 시스템 키 잠금 장치의 키 • #1 및 #2 십자 드라이버 • 손목 접지대 시스템 내부 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다.
그림 3-1.
전면 베젤 (선택 사양) 1 베젤의 좌측 끝에 있는 키 잠금 장치를 잠금 해제합니다. 2 키 잠금 장치 옆의 분리 래치를 위로 올립니다. 3 베젤의 좌측 끝을 회전하여 전면 패널에서 분리합니다. 4 베젤의 우측 끝 고리를 벗기고 베젤을 시스템에서 당겨 빼냅니다. 그림 3-2. 선택 사양의 전면 베젤 분리 및 장착 3 2 1 4 1 분리 래치 2 키 잠금 장치 3 전면 베젤 4 연결쇠 탭 선택 사양의 베젤을 장착하려면 베젤의 우측 끝 고리를 섀시에 건 다음 베 젤의 좌측 끝을 시스템에 끼웁니다. 베젤을 키 잠금 장치로 고정합니다. 그림 3-2를 참조하십시오.
시스템 열기 및 닫기 경고: 시스템을 옮겨야 하는 경우에는 반드시 다른 사람의 도움을 받으십시 오. 부상당할 우려가 있으므로 시스템을 혼자 들지 마십시오. 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 시스템 열기 1 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트 및 주 변 장치에서 분리합니다. 2 분리 래치 잠금 장치를 시계 반대 방향으로 돌려 잠금 해제 위치에 둡니 다. 그림 3-3을 참조하십시오. 3 덮개의 양면을 잡고 분리 래치 잠금 장치와 오목면을 두 엄지 손가락으 로 누릅니다. 덮개를 조심스럽게 시스템 뒤쪽으로 밀고 시스템에서 들 어냅니다.
그림 3-3. 시스템 열기 및 닫기 1 2 1 분리 래치 잠금 장치 2 오목면 시스템 닫기 1 덮개로 섀시 위를 덮은 다음 시스템 뒤쪽으로 살짝 밀어 덮개 후면 모서 리의 두 고리를 섀시 후면 모서리의 해당 슬롯 위에 끼웁니다. 그림 3-3 을 참조하십시오. 2 덮개가 제자리에 고정될 때까지 섀시 전면 쪽으로 밉니다. 3 분리 래치 잠금 장치를 시계 방향으로 돌려 덮개를 고정합니다.
광학 드라이브 (선택 사양) 슬림형 DVD 또는 DVD+/-RW 광학 드라이브 (선택 사양) 를 전면 패널에 밀 어 넣어 시스템 보드의 SATA 컨트롤러에 연결합니다. 주: DVD 장치는 데이터 전용입니다. 광학 드라이브 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 드라이브 후면에서 전원 케이블 및 데이터 케이블을 분리합니다.
그림 3-4.
광학 드라이브 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 금속 격리 애자에 있는 두 개의 노치를 드라이브 옆면의 슬롯에 맞춥 니다. 4 드라이브가 단단히 장착되고 분리 래치가 제자리에 고정될 때까지 드 라이브를 노치에 밀어 넣습니다. 그림 3-4를 참조하십시오. 5 전원 케이블을 연결합니다. 6 드라이브 후면과 시스템 보드의 SATA 커넥터에 데이터 케이블을 연결 합니다.
드라이브 보호물 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 적절한 시스템 냉각을 유지하려면 모든 빈 하드 드라이브 베이에 드라 이브 보호물을 설치해야 합니다. 1 해당하는 경우 전면 베젤을 분리합니다. 77페이지의 "전면 베젤 (선택 사양)"을 참조하십시오. 2 하드 드라이브 보호물의 앞부분을 잡고 오른쪽의 분리 레버를 누른 후 보호물이 드라이브 베이에서 분리될 때까지 잡아당깁니다. 그림 3-5를 참조하십시오. 그림 3-5.
드라이브 보호물 설치 하드 드라이브 보호물을 드라이브 베이에 맞춘 다음 분리 레버가 제자리에 고정될 때까지 보호물을 드라이브 베이에 밀어 넣습니다. 그림 3-5를 참조 하십시오. 하드 드라이브 캐리어 분리 주의: 운영 체제가 핫 스왑 드라이브 설치를 지원하는지 확인하십시오. 운영 체제와 함께 제공된 설명서를 참조하십시오. 1 해당하는 경우 전면 베젤을 분리합니다. 77페이지의 "전면 베젤 (선택 사양)"을 참조하십시오. 2 RAID 관리 소프트웨어를 사용하여 하드 드라이브를 분리할 수 있는 상태로 만듭니다. 하드 드라이브 캐리어의 하드 드라이브 표시등에 드라이브를 안전하게 분리할 수 있다는 신호 가 나타날 때까지 기다 립니다.핫 스왑 하드 드라이브 분리에 대한 내용은 저장소 컨트롤러 설명서를 참조하십시오. 하드 드라이브가 온라인 상태인 경우 하드 드라이브 전원이 꺼질 때 녹 색 작동/오류 표시등이 깜박입니다. 하드 드라이브 표시등이 꺼지면 하드 드라이브를 분리할 수 있습니다.
그림 3-6. 하드 드라이브 캐리어 분리 및 설치 1 3 2 1 분리 단추 3 하드 드라이브 캐리어 2 하드 드라이브 캐리어 핸들 하드 드라이브 캐리어 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 운영 체제가 핫 스왑 드라이브 설치를 지원하는지 확인하십시오. 운영 체제와 함께 제공된 설명서를 참조하십시오. 주의: 동일한 시스템 구성에서는 SATA 및 SAS 하드 드라이브를 함께 사용할 수 없습니다. 1 해당하는 경우 전면 베젤을 분리합니다. 77페이지의 "전면 베젤 (선택 사양)"을 참조하십시오. 2 드라이브 보호물이 베이에 설치된 경우 분리합니다.
하드 드라이브 캐리어에서 하드 드라이브 분리 주의: SAS/SATA 후면판에서 사용할 수 있도록 검사 및 승인된 하드 드라이브 만 사용하십시오. 주의: 하드 드라이브를 설치할 경우 인접한 드라이브가 완전히 설치되어 있 는지 확인합니다. 부분적으로 설치된 캐리어 옆에 하드 드라이브 캐리어를 삽 입하고 해당 핸들을 잠그면 부분적으로 설치된 캐리어의 실드 스프링이 손상 되어 사용하지 못할 수 있습니다. 하드 드라이브 캐리어의 슬라이드 레일에서 나사를 분리한 후 캐리어에서 하드 드라이브를 분리합니다. 그림 3-7을 참조하십시오. 그림 3-7.
하드 드라이브 캐리어에 하드 드라이브 설치 주: 2.5인치 하드 드라이브를 3.5인치 하드 드라이브로 업그레이드할 경우, 캐 리어에 3.5인치 하드 드라이브를 설치하기 전에 캐리어 안의 삽입물을 제거해 야 합니다. 1 드라이브 커넥터 끝이 후면에 놓이도록 하드 드라이브를 하드 드라이 브 캐리어에 넣습니다. 그림 3-7을 참조하십시오. 2 하드 드라이브의 나사 구멍을 하드 드라이브 캐리어 후면의 구멍에 맞 춥니다. 올바르게 맞춰지면 하드 드라이브 후면이 하드 드라이브 캐리어 후면 과 접하게 됩니다. 3 하드 드라이브를 하드 드라이브 캐리어에 고정하는 나사 4개를 장착합 니다. 케이블 연결된 하드 드라이브 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다.
그림 3-8. 케이블 연결된 하드 드라이브 분리 및 설치 2 1 3 4 1 하드 드라이브 2 전원/데이터 케이블 3 탭 4 드라이브 브래킷 주: 하드 드라이브를 장착하지 않을 경우 드라이브 브래킷에서 드라이브를 분리하고 (90페이지의 "하드 드라이브 브래킷에서 하드 드라이브 분리" 참조) 빈 브래킷을 다시 드라이브 베이에 넣습니다. 5 시스템 덮개를 장착합니다. 79페이지의 "시스템 닫기"를 참조하십시오. 케이블 연결된 하드 드라이브 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
3 기존 하드 드라이브 브래킷을 분리합니다. 브래킷에 청색 점이 있는 탭 을 들어 올리고 브래킷을 위쪽으로 밀어 시스템에서 분리하면 됩니다. 그림 3-8을 참조하십시오. 4 하드 드라이브를 브래킷에 설치합니다. 90페이지의 "하드 드라이브 브 래킷에 하드 드라이브 설치"를 참조하십시오. 5 하드 드라이브를 하드 드라이브 베이에 밀어 넣습니다. 6 전원/데이터 케이블을 하드 드라이브에 연결합니다. • 내장형 SATA 컨트롤러에 연결하는 경우 (SATA 하드 드라이브만 해 당), SATA 데이터 케이블을 시스템 보드의 SATA_A 커넥터에 연결 합니다. • SAS RAID 컨트롤러 카드에 연결하는 경우 (SAS 또는 SATA 하드 드 라이브에 해당), 데이터 케이블을 카드 모서리의 커넥터에 연결합 니다. SAS 컨트롤러 카드 설치에 대한 자세한 내용은 93페이지의 "확장 카드 설치"를 참조하십시오. 7 시스템 덮개를 장착합니다. 79페이지의 "시스템 닫기"를 참조하십시오.
하드 드라이브 브래킷에서 하드 드라이브 분리 하드 드라이브 브래킷의 슬라이드 레일에서 나사를 분리한 후 브래킷에서 하드 드라이브를 분리합니다. 그림 3-9를 참조하십시오. 그림 3-9. 하드 드라이브 브래킷에서 하드 드라이브 분리 및 설치 1 2 3 4 1 나사 (4개) * 2 하드 드라이브 3 SAS/SATA 나사 구멍 (4개) 4 하드 드라이브 브래킷 *나사는 Dell에서 주문한 하드 드라이브와 함께 제공됩니다. 하드 드라이브 브래킷에 하드 드라이브 설치 1 드라이브 커넥터 끝이 후면에 놓이도록 하드 드라이브를 하드 드라이 브 브래킷에 넣습니다. 그림 3-9를 참조하십시오. 2 하드 드라이브의 나사 구멍을 하드 드라이브 브래킷 후면의 구멍에 맞 춥니다. 올바르게 맞춰지면 하드 드라이브의 후면은 하드 드라이브 브래킷의 후면과 접하게 됩니다. 3 나사 4개를 장착하여 하드 드라이브를 하드 드라이브 브래킷에 고정합 니다.
확장 카드 확장 카드 설치 지침 시스템은 2개의 확장 카드 라이저에 설치되는 2개의 PCIe Generation 2 확 장 카드를 지원합니다. • 라이저1: PCIE_G2_x16 전체 높이 절반 길이 확장 카드를 지원합니다. • 라이저2: PCIE_G2_x8 전체 높이 절반 길이 확장 카드를 지원합니다. • 확장 카드 슬롯은 핫 스왑할 수 없습니다. • 슬롯에는 PCI Express Generation 1과 Generation 2 확장 카드를 사용할 수 있습니다. 주의: 적절한 냉각을 확보하기 위해서는 두 확장 카드 중 하나만 15W이상 (최 대 25W까지) 의 전력을 소비할 수 있으며 여기에는 내장형 저장소 컨트롤러는 포함되지 않습니다. • 표 3-1에서는 확장 카드 설치 시의 적절한 냉각 및 기계적 규격을 확인하 기 위한 지침을 제공합니다. 표시된 슬롯 우선 순위에 따라 가장 높은 우 선 순위의 확장 카드를 가장 먼저 설치해야 합니다.
표 3-1.
확장 카드 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 확장 카드의 포장을 풀고 설치 준비를 합니다. 지침은 카드와 함께 제공된 설명서를 참조하십시오. 2 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 확장 카드 래치를 들어 올려 필러 브래킷을 분리합니다. 그림 3-10을 참조하십시오. 5 확장 카드의 모서리를 잡고 카드 에지 커넥터가 확장 카드 라이저의 확 장 카드 커넥터에 맞춰지도록 카드를 놓습니다. 그림 3-10을 참조하십 시오.
그림 3-10. 확장 카드 설치 및 분리 1 4 3 2 1 확장 카드 래치 2 확장 카드 3 필러 브래킷 4 확장 카드 라이저 8 확장 카드에 모든 케이블을 연결합니다. 9 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 10 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다.
확장 카드 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 카드에서 모든 케이블을 분리합니다. 4 확장 카드 래치를 들어 올립니다. 그림 3-10을 참조하십시오. 5 확장 카드의 모서리 부분을 잡고 확장 카드 라이저의 커넥터에서 조심 스럽게 분리합니다. 6 확장 카드를 영구 제거할 경우, 빈 확장 카드 슬롯 입구에 금속 필러 브 래킷을 설치합니다. 7 확장 카드 래치를 장착합니다.
확장 카드 라이저 이 시스템의 확장 카드 라이저는 x8 및 x16 링크 Generation 2 PCIe 확장 카 드를 지원합니다. 확장 카드 라이저 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 확장 카드가 설치되어 있는 경우 확장 카드 슬롯에서 분리합니다. 95페이지의 "확장 카드 분리"를 참조하십시오.
그림 3-11.
확장 카드 라이저 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 확장 카드 라이저를 시스템 보드의 라이저 가이드 포스트에 맞춥니다. 그림 3-11을 참조하십시오. 2 확장 카드 라이저 커넥터가 완전히 장착될 때까지 확장 카드 라이저를 내려 제자리에 넣습니다. 3 해당하는 경우에는 확장 카드를 다시 설치합니다. 93페이지의 "확장 카드 설치"를 참조하십시오. 4 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 5 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다.
1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 제어판 보드의 USB 커넥터를 찾습니다. 그림 6-1을 참조하십시오. 4 USB 메모리 키를 USB 커넥터에 삽입합니다. 5 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 6 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다. 그림 3-12.
냉각기 덮개 시스템 보드 덮개는 프로세서, 방열판 및 메모리 모듈을 보호하고 이러한 구성요소에 적절한 공기 흐름을 제공합니다. 냉각기 덮개 바로 밑에 있는 냉각 팬 모듈에 의해 공기 흐름이 원활해집니다. 배전 보드 덮개는 전원 공 급 장치 베이 뒤에 있는 배전 보드를 덮고 있습니다. 냉각기 덮개 분리 경고: 메모리 모듈 및 방열판은 정상적인 작동 중에 매우 뜨거워질 수 있습니 다. 만지기 전에 메모리 모듈과 방열판이 충분히 식을 때까지 기다리십시오. 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 냉각기 덮개를 분리한 상태에서 시스템을 작동하지 마십시오.
그림 3-13. 냉각기 덮개 설치 및 분리 1 2 4 3 1 배전 보드 덮개 2 시스템 보드 덮개 3 탭 (2개) 4 팬 베이 번호 냉각기 덮개 설치 1 냉각기 덮개의 위치를 설명서에 따라 팬 베이의 번호와 맞춥니다. 2 냉각기 덮개 포스트를 시스템 보드의 슬롯에 맞춥니다. 3 모든 모서리가 시스템 보드에 고정될 때까지 냉각기 덮개를 아래로 누 릅니다. 4 시스템을 닫습니다. 78페이지의 "시스템 열기 및 닫기"를 참조하십시오.
내장형 저장소 컨트롤러 카드 해당 시스템은 시스템의 내부 하드 드라이브용 내장형 저장 장치 하위 시 스템을 제공하는 내장형 SAS 또는 PERC 컨트롤러 카드 전용의 확장 카드 슬롯이 라이저에 포함되어 있습니다. 컨트롤러는 SAS와 SATA 하드 드라 이브를 지원하므로 이를 통해 관리자는 하드 드라이브를 시스템에 포함된 저장소 컨트롤러 버전에서 지원하는 RAID 구성으로 설정할 수 있습니다. 내장형 저장소 컨트롤러 카드 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다.
그림 3-14. 내장형 저장소 컨트롤러 카드 분리 및 설치 2 1 4 3 1 내장형 저장소 컨트롤러 카드 커넥터 2 내장형 저장소 컨트롤러 카드 3 분리 탭 4 맞춤 가이드 (2개) 내장형 저장소 컨트롤러 카드 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다.
2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 확장 카드가 설치되어 있는 경우에는 분리합니다. 95페이지의 "확장 카 드 분리"를 참조하십시오. 4 내장형 저장소 컨트롤러 카드를 설치하려면 다음을 수행합니다. a 카드의 모서리를 잡습니다. b 카드를 맞춤 가이드에 따라 맞춥니다. c 카드가 완전히 장착될 때까지 카드 에지 커넥터를 커넥터에 단단히 삽입합니다. 5 시스템을 닫습니다. 78페이지의 "시스템 열기 및 닫기"를 참조하십시오. 6 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다. 시스템 메모리 시스템은 DDR3 버퍼되지 않은 ECC DIMM (UDIMM) 및 레지스터된 ECC DIMM (RDIMM) 을 지원합니다. DIMM은 1066 또는 1333MHz가 될 수 있습니다. 이 시스템에는 2개의 DDR3 채널에 구성된 6개의 메모리 소켓이 포함되어 있습니다. 각 채널의 첫 번째 소켓은 흰색 분리 레버로 표시되어 있습니다.
특정 모드에 따른 지침 시스템은 단일 채널 모드와 이중 채널 모드를 모두 지원합니다. 1GB 메모 리 모듈이 하나인 최소 단일 채널 구성도 이 모드에서 지원됩니다. 표 3-2에서는 이 항목에 설명된 적절한 메모리 지침을 따른 메모리 구성의 예를 보여 줍니다. 이 예제에서는 동일한 메모리 모듈 구성과 그에 따른 실 제 메모리 및 사용 가능한 메모리 총량을 보여 줍니다. 이 표에는 혼합된 메 모리 모듈 구성 또는 4중 등급 메모리 모듈 구성은 나와 있지 않으며 메모 리 모듈 구성 시의 메모리 속도 관련 정보도 나와 있지 않습니다. 표 3-2.
표 3-3. RDIMM 메모리 구성의 예 메모리 모듈 크기 메모리 소켓 1 실제 메모리 (GB) 2 3 4 5 1GB 2GB 4GB 8GB X X X X X X X X X X X X X X X X 6 X X X X X X X X X X X X X 1 2 4 6 X 2 4 8 12 X X X X 4 8 16 X X X 32 메모리 모듈 설치 경고: 시스템의 전원을 끈 후에도 일정 시간 메모리 모듈이 뜨거우므로 건드 리지 마십시오. 메모리 모듈을 다루기 전에 냉각될 때까지 기다립니다. 메모 리 모듈을 다룰 때는 카드 모서리를 잡아야 하며 메모리 모듈의 구성요소를 만지지 마십시오. 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다.
4 메모리 모듈 소켓을 찾습니다. 그림 6-1을 참조하십시오. 5 메모리 모듈을 소켓에 삽입하려면 그림 3-15에서 설명한 대로 메모리 모듈 소켓의 배출기를 아래로 누른 다음 밖으로 당깁니다. 6 메모리 모듈의 중간 부분을 건드리지 않도록 주의하면서 메모리 모듈 의 양쪽 카드 모서리만 잡습니다. 그림 3-15. 메모리 모듈 설치 및 분리 1 2 3 1 메모리 모듈 3 맞춤 키 2 메모리 모듈 소켓 배출기 (2개) 7 메모리 모듈의 에지 커넥터를 메모리 모듈 소켓의 맞춤 키에 맞추고 메 모리 모듈을 소켓에 삽입합니다. 주: 메모리 모듈 소켓에는 메모리 모듈을 소켓에 한 방향으로만 설치할 수 있도록 해주는 맞춤 키가 있습니다.
8 엄지 손가락으로 메모리 모듈을 아래로 눌러 메모리 모듈을 소켓에 고 정합니다. 메모리 모듈이 소켓에 올바르게 장착된 경우 메모리 모듈 소켓의 배출 기는 메모리 모듈이 설치된 다른 소켓의 배출기와 맞춰집니다. 9 나머지 메모리 모듈을 설치하려면 이 절차의 5단계 ~ 8단계를 반복합 니다. 표 3-2를 참조하십시오. 10 냉각기 덮개를 장착합니다. 101페이지의 "냉각기 덮개 설치"를 참조하 십시오. 11 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 12 시스템을 시작하고 키를 눌러 시스템 설치 프로그램을 시작한 다 음 System Setup (시스템 설치 프로그램) 기본 화면에서 System Memory (시스템 메모리) 설정을 확인합니다. 새로 설치된 메모리를 반영하도록 이미 설정값이 변경되어 있어야 합 니다. 13 값이 정확하지 않은 경우 하나 이상의 메모리 모듈이 올바르게 설치되지 않을 수 있습니다.
3 냉각기 덮개를 분리합니다. 100페이지의 "냉각기 덮개 분리"를 참조하십 시오. 4 메모리 모듈 소켓을 찾습니다. 그림 6-1을 참조하십시오. 5 메모리 모듈이 소켓에서 튕겨 나올 때까지 소켓 양쪽 끝의 배출기를 아래 로 누른 다음 밖으로 당깁니다. 그림 3-15를 참조하십시오. 메모리 모듈의 중간 부분을 건드리지 않도록 주의하면서 메모리 모듈의 양쪽 카드 모서리만 잡습니다. 6 냉각기 덮개를 장착합니다. 101페이지의 "냉각기 덮개 설치"를 참조하십 시오. 7 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 8 시스템 및 주변 장치를 해당 전원에 다시 연결하고 켭니다. 냉각 팬 시스템은 5개의 단일 모터 팬을 포함하며 프로세서, 확장 카드, 전원 공급 장치 및 메모리 모듈에 대한 냉각 기능을 제공합니다. 주: 팬의 핫 스왑 분리 또는 설치는 지원되지 않습니다.
3 해당하는 경우 냉각기 덮개 또는 배전 보드 덮개를 분리합니다. 100페이 지의 "냉각기 덮개"를 참조하십시오. 4 시스템 보드에서 팬의 전원 케이블을 분리합니다. 그림 3-16을 참조하 십시오. 5 팬을 잡고 팬 조립품에서 밀어 꺼냅니다. 그림 3-16을 참조하십시오. 그림 3-16.
냉각 팬 설치 1 팬의 방향이 올바른지 확인합니다. 전원 케이블이 있는 쪽이 시스템 후면을 향하도록 팬 모듈의 방향을 정합 니다. 2 팬이 완전히 제자리에 들어갈 때까지 팬을 팬 조립품에 내려놓습니다. 그림 3-16을 참조하십시오. 3 팬의 전원 케이블을 시스템 보드의 전원 커넥터에 연결합니다. 4 해당하는 경우 냉각기 덮개 또는 배전 보드 덮개를 분리합니다. 101페이 지의 "냉각기 덮개 설치"를 참조하십시오. 5 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 6 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전 원을 모두 켭니다. iDRAC6 Express 카드 (선택 사양) iDRAC6 Express 카드 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다.
그림 3-17. iDRAC6 Express 카드 설치 또는 분리 2 3 1 1 iDRAC6 Express 카드 3 고정 격리 애자 탭 2 iDRAC6 Express 카드 커넥터 7 해당하는 경우 확장 카드를 장착합니다. 93페이지의 "확장 카드 설치"를 참조하십시오. 8 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 9 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다.
iDRAC6 Express 카드 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 확장 카드가 설치되어 있는 경우 확장 카드 슬롯에서 분리합니다. 95페이지의 "확장 카드 분리"를 참조하십시오. 4 카드의 전면 모서리에 있는 고정 격리 애자 탭을 살짝 뒤로 당기고 카드 를 고정 격리 애자에서 조심스럽게 들어 올립니다. 그림 3-17을 참조하십시오.
iDRAC6 Enterprise 카드 (선택 사양) iDRAC6 Enterprise 카드 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 확장 카드가 설치되어 있는 경우 확장 카드 슬롯에서 분리합니다. 95페이지의 "확장 카드 분리"를 참조하십시오. 4 시스템 후면 패널에서 iDRAC6 Enterprise 포트용 플라스틱 필러 플러그 를 분리합니다.
그림 3-18. iDRAC6 Enterprise 카드 설치 및 분리 5 1 4 2 3 1 VFlash SD 카드 2 VFlash 매체 슬롯 3 iDRAC6 Enterprise 카드 커넥터 4 고정 격리 애자 포스트 (2개) 5 iDRAC6 Enterprise 카드 7 해당하는 경우 확장 카드를 장착합니다. 93페이지의 "확장 카드 설치"를 참조하십시오. 8 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 9 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다.
iDRAC6 Enterprise 카드 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 이더넷 케이블이 있는 경우 시스템 후면 패널의 iDRAC6 Enterprise 카 드 커넥터에서 분리합니다. 그림 1-4를 참조하십시오. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 확장 카드가 설치되어 있는 경우 확장 카드 슬롯에서 분리합니다. 95페이지의 "확장 카드 분리"를 참조하십시오.
VFlash 매체 (선택 사양) VFlash 매체 카드는 시스템 뒤쪽 모서리에 있는 iDRAC6 Enterprise 카드 (선택 사양) 에 꽂는 SD (Secure Digital) 카드입니다. VFlash 매체 카드 설치 1 시스템 뒤쪽 모서리에 있는 VFlash 매체 슬롯을 찾습니다. 2 레이블 면이 위를 향하게 한 후 SD 카드의 접촉 핀 끝을 모듈의 카드 슬 롯에 삽입합니다. 주: 슬롯은 카드를 올바르게 삽입할 수 있도록 설계되어 있습니다. 3 카드를 슬롯 안쪽으로 밀어 고정합니다. VFlash 매체 카드 분리 VFlash 매체 카드를 분리하려면 먼저 카드를 안쪽으로 눌러 분리한 다음 카드 슬롯에서 잡아당깁니다. 프로세서 프로세서 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다.
경고: 방열판과 프로세서는 시스템의 전원을 끈 후에도 잠시 동안은 손댈 수 없을 정도로 뜨겁습니다. 방열판과 프로세서를 다루기 전에 냉각될 때까지 기 다립니다. 주의: 프로세서를 분리하지 않을 경우, 프로세서에서 방열판을 분리하지 마 십시오. 방열판은 적절한 온도 상태를 유지하는 데 필요합니다. 5 #2 십자 드라이버를 사용하여 방열판 고정 나사 중 하나를 풉니다. 그림 3-19를 참조하십시오. 6 방열판이 프로세서에서 느슨해질 때까지 30초 정도 기다립니다. 7 다른 쪽 방열판 고정 나사를 풉니다. 8 프로세서의 방열판을 조심스럽게 들어 올려 떼어낸 후 열 그리즈 면이 위쪽을 향하도록 방열판을 놓습니다. 주의: 강한 힘으로 프로세서를 해당 소켓에 고정해야 합니다. 단단히 잡지 않 으면 분리 레버가 갑자기 튕겨 나올 수 있습니다. 9 엄지 손가락을 프로세서 소켓 분리 레버 위에 단단히 놓은 후 레버를 잠 금 위치에서 분리합니다. 10 프로세서가 소켓에서 분리될 때까지 레버를 90도 각도로 위로 돌립니다.
그림 3-19. 방열판 설치 및 분리 2 1 1 방열판 고정 나사 (4개) 2 방열판 11 프로세서 실드를 위로 돌려 꺼냅니다. 그림 3-20을 참조하십시오. 12 프로세서를 소켓에서 들어 꺼내고 분리 레버를 위로 올린 상태로 두어 소켓에 새 프로세서를 설치할 수 있도록 준비합니다. 주의: 프로세서를 분리할 때 ZIF 소켓의 핀이 구부러지지 않도록 주의하십시 오. 핀이 구부러지면 시스템 보드가 영구적으로 손상될 수 있습니다.
그림 3-20.
프로세서 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 프로세서를 업그레이드할 경우 해당 시스템을 업그레이드하기에 앞서 support.dell.com에서 최신 시스템 BIOS 버전을 다운로드하여 설치합니 다. 다운로드한 파일에 포함된 지침에 따라 해당 시스템의 업데이트를 설치합니다. 2 사용한 적이 없는 프로세서인 경우에는 포장을 풉니다. 사용한 적이 있는 프로세서인 경우에는 보풀이 없는 천을 사용하여 프 로세서 상단에 묻어 있는 열 그리즈를 닦아냅니다. 3 프로세서를 ZIF 소켓의 소켓 키에 맞춥니다. 그림 3-20을 참조하십시오.
12 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 13 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다. 14 키를 눌러 시스템 설치 프로그램을 시작하고 프로세서 정보가 새 로운 시스템 구성과 일치하는지 확인합니다. 54페이지의 "시스템 설치 프로그램 시작"을 참조하십시오. 15 시스템 진단 프로그램을 실행하여 새 프로세서가 올바르게 작동하는지 확인합니다. 진단 프로그램 실행에 대한 내용은 156페이지의 "내장형 시스템 진단 프로그램 실행"을 참조하십시오. 전원 공급 장치 시스템은 다음의 전원 공급 장치 모듈을 지원합니다. • 350W (비중복 전원 공급 장치) • 400W (중복 전원 공급 장치) 전원 공급 장치가 2개 설치된 경우 두 번째 전원 공급 장치는 핫 스왑 가능 한 전원 중복성을 제공합니다. 중복 모드에서 시스템은 전원 부하를 두 전 원 공급 장치 모두에 배포하여 효율을 최적화합니다.
2 전원 공급 장치에서 전원 케이블을 분리하고 시스템 케이블을 묶고 고 정하는 당김 안전 끈을 분리합니다. 주: 케이블 관리대 (선택 사양) 가 전원 공급 장치 분리를 방해하는 경우 에는 관리대의 래치를 풀고 들어 내야 할 수도 있습니다. 케이블 관리대 에 대한 내용은 시스템의 랙 설명서를 참조하십시오. 3 분리 래치를 누르고 전원 공급 장치를 일직선으로 당겨 배전 보드에서 분리한 다음 섀시에서 빼냅니다. 그림 3-21.
중복 전원 공급 장치 설치 1 두 전원 공급 장치의 유형과 최대 출력 전원이 동일한지 확인합니다. 주: 최대 출력 전원 (와트 단위로 표기) 은 전원 공급 장치 레이블에 표시 되어 있습니다. 2 해당하는 경우 전원 공급 장치 보호물을 분리합니다. 124페이지의 "전 원 공급 장치 보호물 분리"를 참조하십시오. 3 전원 공급 장치가 완전히 장착되고 분리 래치가 제자리에 고정될 때까지 새 전원 공급 장치를 섀시에 밀어 넣습니다. 그림 3-21을 참조하십시오. 주: 이전 절차의 단계 2에서 케이블 관리대의 래치를 벗긴 경우 다시 래 치를 고정합니다. 케이블 관리대에 대한 내용은 시스템의 랙 설명서를 참조하십시오. 4 전원 케이블을 전원 공급 장치에 연결하고 케이블을 전원 콘센트에 연 결합니다. 주의: 전원 케이블을 연결할 때는 당김 안전 끈으로 케이블을 고정합니다.
비중복 전원 공급 장치 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 연결된 모든 주변 장치를 끕니다. 2 전원 케이블을 전원에서 분리합니다. 3 전원 공급 장치에서 전원 케이블을 분리하고 시스템 케이블을 묶고 고 정하는 당김 안전 끈을 분리합니다. 주: 케이블 관리대 (선택 사양) 가 전원 공급 장치 분리를 방해하는 경우 에는 관리대의 래치를 풀고 들어 내야 할 수도 있습니다. 케이블 관리대 에 대한 내용은 시스템의 랙 설명서를 참조하십시오. 4 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오.
그림 3-22. 비중복 전원 공급 장치 분리 및 설치 2 1 5 3 4 1 전원 공급 장치 2 나사 3 8핀 전원 케이블 4 24핀 전원 케이블 5 SATA 전원 케이블 비중복 전원 공급 장치 설치 1 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 2 전원 공급 장치를 섀시에 놓습니다. 그림 3-22 참조하십시오. 나사를 조 여 전원 공급 장치를 섀시에 고정합니다. 3 모든 전원 케이블을 시스템 보드, 하드 드라이브 및 광학 드라이브에 연 결합니다. 4 시스템 덮개를 장착합니다. 79페이지의 "시스템 닫기"를 참조하십시오. 5 전원 케이블을 전원 공급 장치에 연결하고 케이블을 전원 콘센트에 연 결합니다.
시스템 전지 시스템 전지 교체 경고: 새 전지를 올바르게 설치하지 않으면 전지가 파열될 위험이 있습니다. 제조업체에서 권장하는 것과 동일하거나 동등한 종류의 전지로만 교체합니 다. 자세한 내용은 해당 안전 정보를 참조하십시오. 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 그림 3-23.
3 전지 소켓을 찾습니다. 그림 6-1을 참조하십시오. 주의: 전지 커넥터의 손상을 방지하려면 전지를 설치하거나 분리할 때 커넥 터를 단단히 잡아야 합니다. 4 전지를 분리하려면 전지가 튕겨 나올 때까지 전지의 바깥쪽으로 금속 탭을 누릅니다. 그림 3-23을 참조하십시오. 5 새 시스템 전지를 설치하려면 "+"가 위로 향하게 전지를 잡고 소켓의 금 속 탭에 맞춥니다. 6 전지가 제자리에 고정될 때까지 소켓쪽으로 똑바로 누릅니다. 7 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 8 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다. 9 전지가 올바르게 작동하는지 확인하려면 시스템 설치 프로그램을 시작 합니다. 54페이지의 "시스템 설치 프로그램 시작"을 참조하십시오. 10 시스템 설치 프로그램의 Time (시간) 및 Date (날짜) 필드에 정확한 시 간 및 날짜를 입력합니다. 11 시스템 설치 프로그램을 종료합니다.
제어판 조립품 주: LCD 제어판 조립품은 2개의 별도 모듈 (디스플레이 모듈 및 제어판 회로 보 드) 로 구성되어 있습니다. 각 모듈을 분리하거나 설치하려면 다음 지침을 따 릅니다. 제어판 보드 조립품 및 제어판 디스플레이 모듈 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 선택 사양인 전면 베젤이 설치되어 있는 경우 전면 베젤을 분리합니다. 77페이지의 "전면 베젤 (선택 사양)"을 참조하십시오. 2 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트 및 주 변 장치에서 분리합니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오.
그림 3-24.
제어판 보드 조립품 및 제어판 디스플레이 모듈 설치 LED 제어판의 경우 3단계를 진행하십시오. 디스플레이 모듈을 섀시 컷아 웃에 삽입하고 두 개의 나사로 고정합니다. 1 교체 패널을 디스플레이 모듈의 전면에 연결합니다. 2 제어판 보드에 있는 슬롯을 시스템 섀시의 격리 애자에 맞춘 다음 나사 두 개로 고정합니다. 그림 3-24를 참조하십시오. LED 제어판의 경우 4 단계를 생략합니다. 3 디스플레이 모듈 케이블을 제어판 보드에 연결합니다. 4 USB 및 제어판 케이블을 제어판 보드에 연결합니다. 5 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 6 해당하는 경우 선택 사양인 전면 베젤을 장착합니다. 77페이지의 "전면 베젤 (선택 사양)"을 참조하십시오. 7 시스템을 전원에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 켭니다. SAS 후면판 SAS 후면판 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다.
5 후면판에서 SAS 데이터 케이블을 분리합니다. 그림 3-25를 참조하십시오. 6 광학 드라이브 케이블, 제어판 케이블, 전원 케이블, 데이터 케이블 및 USB 케이블을 분리합니다. 7 SAS 후면판의 양 끝에 있는 두 개의 청색 고정 래치를 누른 다음 위로 들 어 올려 고정 고리 밖으로 빼냅니다. 보드 앞면의 다른 구성요소가 손상 되지 않도록 주의를 기울여야 합니다. 그림 3-25를 참조하십시오. 8 SAS 후면판을 뒤집어 작업대 표면에 놓습니다. 그림 3-25.
SAS 후면판 설치 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 SAS 후면판을 설치합니다. a 보드 표면의 구성요소가 손상되지 않도록 주의하면서 후면판을 시 스템에 내려놓습니다. b 양 끝에 있는 두 개의 청색 고정 래치를 시스템 보드의 가이드 포스 트에 맞춥니다. 그림 3-25를 참조하십시오. c 두 청색 고정 래치가 제자리에 걸릴 때까지 후면판을 아래로 밀어 내립니다. 2 SAS 데이터 및 전원 케이블을 SAS 후면판에 연결합니다. 3 SAS 후면판을 제거하면서 분리되었을 수 있는 다른 장치 케이블을 다시 연결합니다. 4 하드 드라이브를 원래 위치에 설치합니다.
2 배전 보드 덮개를 찾아 들어 올립니다. 100페이지의 "냉각기 덮개 분리"를 참조하십시오. 3 시스템 보드에서 배전 케이블을 분리 (136페이지의 "시스템 보드" 참조) 하고 팬 케이블 커넥터를 분리합니다. 4 배전 보드를 섀시에 고정하는 두 개의 나사를 분리하고 보드 밖으로 들 어냅니다. 그림 3-26을 참조하십시오. 그림 3-26.
배전 보드 장착 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 새 배전 보드 조립품을 포장에서 꺼냅니다. 2 배전 보드를 섀시의 격리 애자에 맞춥니다. 그림 3-26을 참조하십시오. 3 배전 보드를 섀시에 고정하는 나사 두 개를 설치합니다. 그림 3-26을 참 조하십시오. 4 배전 케이블을 시스템 보드에 연결하고 (136페이지의 "시스템 보드" 참 조) 그림 3-26에 표시된 것과 같이 배전 보드에 팬 케이블 커넥터를 연결 합니다. 5 덮개 양쪽에서 연결쇠로 연결된 안쪽 래치를 찾아 배전 보드 덮개를 맞 추고 장착한 다음 아래로 돌려 덮개 위에 놓습니다.
시스템 보드 시스템 보드 분리 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 암호화 키를 사용하여 TPM (신뢰할 수 있는 프로그램 모듈) 을 사용하 는 경우 프로그램 또는 시스템 설치 중에 복구 키를 작성하라는 메시지가 표 시될 수 있습니다. 이 복구 키를 작성하여 안전하게 보관해 두십시오. 이 시스 템 보드를 교체하면 시스템 또는 프로그램을 재시작할 때 복구 키를 입력해야 만 하드 드라이브의 암호화된 데이터에 액세스할 수 있습니다. 1 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다. 2 시스템을 엽니다.
12 시스템 보드를 섀시에 고정하는 나사 9개를 분리한 다음 시스템 보드 조 립품을 섀시 전면 쪽으로 밉니다. 주의: 메모리 모듈, 프로세서 또는 그 밖의 구성요소를 잡고 시스템 보드 조립 품을 들어 올리지 마십시오. 13 시스템 보드 조립품의 모서리를 잡고 섀시에서 조립품을 들어 올립니다. 그림 3-27를 참조하십시오. 그림 3-27. 시스템 보드 분리 및 설치 1 2 1 나사 (9개) 2 시스템 보드 조립품 시스템 보드 설치 1 새 시스템 보드의 포장을 풉니다. 2 프로세서 실드에서 레이블을 분리하여 이를 시스템 전면의 시스템 확 인 패널에 부착합니다. 그림 1-1을 참조하십시오. 3 시스템 보드의 모서리를 잡고 섀시에 내려놓습니다.
주의: 메모리 모듈, 프로세서 또는 그 밖의 구성요소를 잡고 시스템 보드 조립 품을 들어 올리지 마십시오. 4 시스템 보드의 전면을 살짝 들어 올리고 시스템 보드가 완전히 평평하 게 놓일 때까지 섀시 하단으로 이동합니다. 5 시스템 보드가 제자리에 고정될 때까지 섀시 후면 쪽으로 밉니다. 6 섀시에 시스템 보드를 고정하는 나사 10개를 조입니다. 그림 3-27을 참조하십시오. 7 프로세서 및 방열판을 새 시스템 보드로 이동합니다. 117페이지의 "프로세서 분리" 및 121페이지의 "프로세서 설치"를 참조 하십시오. 8 메모리 모듈을 모두 장착합니다. 106페이지의 "메모리 모듈 설치"를 참 조하십시오. 9 아래 나열한 순서대로 케이블을 연결합니다. 시스템 보드의 커넥터 위 치에 대한 내용은 그림 6-1을 참조하십시오.
시스템 문제 해결 안전 제일 — 사용자와 사용자 시스템의 안전 을 위하여 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 시스템 시작 오류 문제 해결 시스템을 시작할 때 비디오 출력 전에 시스템이 멈추는 경우, 특히 운영 체 제를 설치하거나 시스템의 하드웨어를 다시 구성한 후에 이러한 현상이 발 생하면 다음 상태를 확인하십시오. • UEFI 부팅 관리자에서 운영 체제를 설치한 후 BIOS 부팅 모드로 시스템 을 부팅하거나 그 반대로 부팅하는 경우 시스템이 중단됩니다. 운영 체 제를 설치한 모드와 동일한 부팅 모드에서 부팅해야 합니다.
비디오 하위 시스템 문제 해결 1 모니터에 대한 시스템 및 전원 연결을 검사합니다. 2 시스템과 모니터 사이의 비디오 인터페이스 케이블 연결을 검사합니다. 3 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"을 참조하십시오. 검사가 성공적으로 완료되는 경우 비디오 하드웨어에 관련된 문제가 아닙니다. 검사가 실패하면 163페이지의 "도움말 얻기"를 참조하십시오. USB 장치 문제 해결 USB 키보드/마우스 문제를 해결하려면 다음 단계를 수행하십시오. 다른 USB 장치의 경우 4단계로 이동합니다. 1 시스템에서 키보드 및 마우스 케이블을 잠깐 분리했다가 다시 연결합 니다. 2 키보드 또는 마우스를 시스템의 반대쪽에 있는 USB 포트에 연결합니다. 3 문제가 해결되면 시스템을 재시작하고 시스템 설치 프로그램을 시작하 여 작동하지 않는 USB 포트가 활성화되었는지 확인합니다. 4 작동하는 다른 키보드 또는 마우스로 교체합니다.
10 장치에서 같은 문제가 발생하면 장치 전원을 끄고 USB 케이블을 교체 한 다음 장치 전원을 켭니다. 문제가 지속되면 장치를 교체합니다. 문제가 해결되지 않으면 163페이지의 "도움말 얻기"를 참조하십시오. 직렬 I/O 장치 문제 해결 1 시스템 및 직렬 포트에 연결된 모든 주변 장치를 끕니다. 2 올바르게 작동하는 케이블로 직렬 인터페이스 케이블을 교환하고 시스 템 및 직렬 장치의 전원을 켭니다. 문제가 해결되면 인터페이스 케이블을 교체합니다. 3 시스템 및 직렬 장치를 끄고 유사한 장치로 교환합니다. 4 시스템 및 직렬 장치의 전원을 켭니다. 문제가 해결되면 직렬 장치를 교체합니다. 문제가 지속되면 163페이지의 "도움말 얻기"를 참조하십시오. NIC 문제 해결 1 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"을 참조하십시오. 2 시스템을 재시작하고 NIC 컨트롤러와 관련된 시스템 메시지를 확인합 니다. 3 NIC 커넥터에서 해당 표시등을 확인합니다.
4 적절한 드라이버가 설치되어 있고 프로토콜이 연결되어 있는지 확인합 니다. NIC 설명서를 참조하십시오. 5 시스템 설치 프로그램을 시작하고 NIC 포트가 활성화되었는지 확인합니 다. 60페이지의 "Integrated Devices (내장형 장치) 화면"을 참조하십시오. 6 네트워크의 NIC, 허브 및 스위치가 모두 동일한 데이터 전송 속도로 설 정되었는지 확인합니다. 각 네트워크 장치의 설명서를 참조하십시오. 7 모든 네트워크 케이블의 유형이 올바르고 최대 길이를 초과하지 않는 지 확인합니다. 문제가 해결되지 않으면 163페이지의 "도움말 얻기"를 참조하십시오. 습식 시스템 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다.
4 최소한 하루 정도 시스템을 완전히 건조시킵니다. 5 3단계에서 분리한 구성요소를 다시 설치합니다. 6 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 7 시스템을 전원 콘센트에 다시 연결하고 시스템을 켭니다. 시스템이 올바르게 시작되지 않으면 163페이지의 "도움말 얻기"를 참조 하십시오. 8 시스템이 올바르게 시작되면 시스템을 종료하고 분리한 확장 카드를 다시 설치합니다. 93페이지의 "확장 카드 설치"를 참조하십시오 9 시스템을 재시작합니다. 10 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"를 참조하십시오. 검사가 실패하면 163페이지의 "도움말 얻기"를 참조하십시오. 손상된 시스템 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다.
6 시스템 진단 프로그램에서 시스템 보드 검사를 실행합니다. 155페이지 의 "시스템 진단 프로그램 실행"을 참조하십시오. 검사가 실패하면 163페이지의 "도움말 얻기"를 참조하십시오. 시스템 전지 문제 해결 주: 장기간 (몇 주 또는 몇 달) 시스템을 사용하지 않은 경우 NVRAM의 시스템 구성 정보가 유실될 수 있습니다. 이 문제는 불량 전지로 인해 발생합니다. 1 시스템 설치 프로그램을 통해 시간 및 날짜를 다시 입력합니다. 53페이지 의 "시스템 설치 프로그램 및 UEFI 부팅 관리자 사용"을 참조하십시오. 2 시스템을 끄고 한 시간 이상 전원 콘센트에서 분리합니다. 3 시스템을 전원 콘센트에 다시 연결하고 시스템을 켭니다. 4 시스템 설치 프로그램을 시작합니다. 시스템 설치 프로그램의 시간 및 날짜가 정확하지 않은 경우 전지를 교 체합니다. 127페이지의 "시스템 전지 교체"를 참조하십시오. 전지를 교체해도 문제가 해결되지 않는 경우 163페이지의 "도움말 얻기" 를 참조하십시오.
전원 공급 장치 문제 해결 주의: 시스템이 작동하려면 하나 이상의 전원 공급 장치가 설치되어 있어야 합니다. 하나의 전원 공급 장치만 설치된 상태에서 시스템을 오랫동안 작동하 는 경우 시스템이 과열될 수 있습니다. 1 전원 공급 장치를 분리한 다음 다시 설치하는 방법으로 다시 장착합니 다. 122페이지의 "전원 공급 장치"를 참조하십시오. 주: 전원 공급 장치를 설치한 후, 시스템에서 전원 공급 장치를 인식하고 올바르게 작동하는지 확인하는 데 몇 초의 시간이 걸립니다. 전원 공급 장치가 올바르게 작동할 경우 전원 표시등은 녹색으로 켜집니다. 2 문제가 지속되면 오류 있는 전원 공급 장치를 교체합니다. 전원 공급 장치를 교체해도 문제가 해결되지 않은 경우 163페이지의 "도 움말 얻기"를 참조하십시오. 시스템 냉각 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다.
팬 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 진단 소프트웨어에 표시된 오류 있는 팬의 위치를 찾습니다. 2 시스템 및 연결된 모든 주변 장치를 끕니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 팬의 전원 케이블을 다시 장착합니다. 5 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 켭니다. 팬이 올바르게 작동하면 시스템을 닫습니다. 79페이지의 "시스템 닫기" 를 참조하십시오. 6 팬이 작동하지 않으면 시스템을 끄고 새 팬을 설치합니다. 109페이지의 "냉각 팬"을 참조하십시오 7 시스템을 재시작합니다.
시스템 메모리 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주: 메모리 구성이 잘못된 경우 시작 단계에서 어떠한 비디오도 출력되지 않 고 시스템이 중단될 수 있습니다. 104페이지의 "일반 메모리 모듈 설치 지침"을 참조하고 메모리 구성이 적용 가능한 모든 지침을 준수하는지 확인하십시오. 1 시스템이 작동할 경우 적절한 온라인 진단 검사를 실행합니다. 155페이 지의 "시스템 진단 프로그램 실행"을 참조하십시오. 진단 프로그램에서 오류 있음을 나타내면 진단 프로그램에서 제공한 수정 조치를 따릅니다.
10 시스템을 전원 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 켭니다. 11 시스템 설치 프로그램을 시작하고 시스템 메모리 설정을 확인합니다. 57페이지의 "Memory Settings (메모리 설정) 화면"을 참조하십시오. 문제가 해결되지 않으면 다음 단계를 계속 진행합니다. 12 시스템 및 연결된 주변 장치의 전원을 끄고 시스템에서 전원 연결을 분 리합니다. 13 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 14 진단 검사나 오류 메시지가 특정 메모리 모듈에 결함이 있음을 나타내 면 이 모듈을 교환하거나 교체합니다. 15 지정되지 않은 오류 있는 메모리 모듈의 문제를 해결하려면 첫 번째 DIMM 소켓에 있는 메모리 모듈을 같은 유형 및 용량의 모듈로 교체합 니다. 106페이지의 "메모리 모듈 설치"를 참조하십시오. 16 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오.
내부 USB 키 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 시스템 설치 프로그램을 시작하고 USB 키 포트가 활성화되었는지 확인 합니다. 60페이지의 "Integrated Devices (내장형 장치) 화면"을 참조하 십시오. 2 시스템 및 연결된 주변 장치의 전원을 끕니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 USB 키를 찾아 다시 장착합니다. 98페이지의 "내부 USB 메모리 키"를 참조하십시오. 5 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오.
광학 드라이브 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 다른 CD 또는 DVD를 사용해 봅니다. 2 시스템 설치 프로그램을 시작하고 드라이브의 컨트롤러가 활성화되었 는지 확인합니다. 54페이지의 "시스템 설치 프로그램 시작"을 참조하십 시오. 3 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"을 참조하십시오. 4 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다. 5 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오.
테이프 백업 장치 문제 해결 주: 테이프 드라이브 문제를 해결할 때 support.dell.com/manuals에 있는 테이 프 드라이브 설명서나 드라이브와 함께 제공된 설명서를 참조하십시오. 1 테이프 드라이브가 켜져 있는지 확인합니다. 2 다른 테이프 카트리지를 사용해 봅니다. 3 테이프 드라이브에 필요한 장치 드라이버가 설치되고 올바르게 구성되 었는지 확인합니다. 장치 드라이버에 대한 자세한 내용은 해당 테이프 드라이브의 설명서를 참조하십시오. 4 테이프 드라이브의 인터페이스 케이블이 컨트롤러 카드의 외부 포트에 제대로 연결되었는지 확인합니다. 5 SCSI 테이프 드라이브의 경우 테이프 드라이브가 고유 SCSI ID 번호로 구성되고 드라이브를 연결하는 데 사용된 인터페이스 케이블에 따라 테이프 드라이브가 종료되었는지 여부를 확인합니다. SCSI ID 번호를 선택하고 종단을 활성화 또는 비활성화하는 데 대한 지 침은 테이프 드라이브 설명서를 참조하십시오. 6 적절한 온라인 진단 검사를 실행합니다.
하드 드라이브 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 이 문제 해결 절차로 인해 하드 드라이브에 저장된 데이터가 삭제될 수 있습니다. 계속하기 전에 하드 드라이브에 있는 모든 파일을 백업합니다. 1 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"을 참조하십시오. 진단 검사 결과에 따라 필요한 경우 다음 단계를 수행합니다. 2 시스템에 RAID 컨트롤러 카드가 있고 하드 드라이브가 RAID 배열로 구성된 경우 다음 단계를 수행합니다.
확장 카드 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주: 확장 카드의 문제를 해결하려면 운영 체제 및 확장 카드 설명서를 참조하 십시오. 1 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "시스템 진단 프 로그램 실행"을 참조하십시오. 2 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 확장 카드 라이저가 해당 커넥터에 단단히 연결되었는지 확인합니다. 93페이지의 "확장 카드 설치"를 참조하십시오. 5 확장 카드가 해당 커넥터에 단단히 연결되었는지 확인합니다.
프로세서 문제 해결 주의: 대부분의 수리 작업은 공인된 서비스 기술자만 수행할 수 있습니다. 사용자는 제품 설명서에서 허가한 경우나 온라인 또는 전화서비스/지원팀에 서 지시한 경우에만 문제 해결 절차 및 단순 수리 작업을 수행할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1 적절한 온라인 진단 검사를 실행합니다. 155페이지의 "온라인 진단 프 로그램 사용"을 참조하십시오. 2 시스템 및 연결된 주변 장치의 전원을 끄고 시스템을 전원 콘센트에서 분리합니다. 3 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 4 냉각기 덮개를 분리합니다. 100페이지의 "냉각기 덮개 분리"를 참조하 십시오. 5 프로세서 및 방열판이 올바르게 설치되었는지 확인합니다. 117페이지의 "프로세서"를 참조하십시오. 6 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오.
시스템 진단 프로그램 실행 시스템에 문제가 발생하면 기술 지원에 문의하기 전에 진단 프로그램을 실 행합니다. 진단 프로그램의 목적은 추가 장비가 필요 없이 데이터를 유실 하지 않고 시스템 하드웨어를 검사하기 위한 것입니다. 자체적으로 문제 를 해결할 수 없는 경우에는 서비스 및 지원 직원이 진단 검사 결과를 사용 하여 문제 해결을 지원할 수 있습니다. 온라인 진단 프로그램 사용 시스템 문제를 평가하려면 먼저 온라인 진단 프로그램을 사용합니다. 온라 인 진단 프로그램은 하드 드라이브, 실제 메모리, 통신 및 프린터 포트, NIC, CMOS 등과 같은 섀시 및 저장소 구성요소에 대한 진단 검사를 포함한 진 단 프로그램 또는 검사 모듈을 일컫는 제품군입니다. 온라인 진단 프로그램 을 사용하여 문제를 식별할 수 없는 경우 내장형 시스템 진단 프로그램을 사용합니다.
• 검사가 성공적으로 완료되었는지 알려 주는 상태 메시지를 봅니다. • 검사 중에 발생한 문제를 알려 주는 오류 메시지를 봅니다. 내장형 시스템 진단 프로그램 사용 시기 시스템의 주요 구성요소 또는 장치가 올바르게 작동하지 않는 경우 구성요 소 오류가 표시될 수 있습니다. 프로세서 및 시스템의 입출력 장치가 작동 하면 내장형 시스템 진단 프로그램을 사용하여 문제를 확인할 수 있습니다. 내장형 시스템 진단 프로그램 실행 내장형 시스템 진단 프로그램은 Lifecycle Controller 화면에서 실행됩니다. 주의: 내장형 시스템 진단 프로그램은 해당 시스템을 검사하는 데만 사용합 니다. 이 프로그램을 다른 시스템에 사용하면 잘못된 결과 또는 오류 메시지 가 표시될 수 있습니다. 1 시스템 부팅 시 키를 누릅니다. 2 왼쪽 창에서 Diagnostics (진단 프로그램) 를 클릭하고 오른쪽 창에서 Launch Diagnostics (진단 프로그램 시작) 를 클릭합니다.
사용자 정의 검사 옵션 사용 Main Menu (기본 메뉴) 창에서 Custom Test (사용자 정의 검사) 를 선택할 경우 Customize (사용자 정의) 창이 나타나며, 이 창에서 검사할 장치 및 검사를 위한 특정 옵션을 선택하고 검사 결과를 볼 수 있습니다. 검사할 장치 선택 Customize (사용자 정의) 창의 왼쪽에는 검사할 수 있는 장치가 표시됩니 다. 장치 또는 모듈의 구성요소를 보려면 장치 또는 모듈 옆의 (+) 를 클릭 합니다. 사용 가능한 검사를 보려면 구성요소에 있는 (+) 를 클릭합니다. 해당 구성요소 대신 장치를 클릭하면 검사할 장치의 모든 구성요소가 선택 됩니다. 주: 검사할 모든 장치 및 구성요소를 선택한 후 All Devices (모든 장치) 를 강조 표시한 다음 Run Tests (검사 실행) 를 클릭합니다. 진단 프로그램 옵션 선택 Diagnostics Options (진단 프로그램 옵션) 영역에서 장치에 실행할 검사를 선택합니다.
• Configuration (구성) — 현재 선택한 장치에 대한 기본 구성 정보를 표 시합니다. • Parameters (매개변수) — 검사에 설정할 수 있는 매개변수를 표시합니다.
점퍼 및 커넥터 이 항목에서는 시스템 점퍼에 대한 자세한 정보를 제공합니다. 또한 점퍼 및 스위치에 대한 일부 기본 정보를 제공하며 시스템 보드에 있는 커넥터 에 대해 설명합니다. 시스템 보드 점퍼 그림 6-1에서는 시스템 보드상의 구성 점퍼의 위치를 보여 줍니다. 표 6-1에 는 점퍼 설정이 나열되어 있습니다. 표 6-1. 시스템 보드 점퍼 설정 점퍼 PWRD_EN 설정 설명 (기본값) 암호 기능이 활성화됩니다. (핀 2-4) 암호 기능이 비활성화됩니다. (핀 4–6) NVRAM_CLR (기본값) 시스템 부팅 시 구성 설정이 유지됩니다 (핀 3-5). 다음 시스템 부팅 시 구성 설정이 지워집 니다 (핀 1-3).
시스템 보드 커넥터 그림 6-1.
항목 커넥터 설명 1 PWRD_EN 암호 활성 점퍼 NVRAM_CLR NVRAM 지우기 점퍼 2 RISER2 확장 카드 라이저 커넥터 3 RISER1 확장 카드 라이저 커넥터 4 iDRAC6 Enterprise iDRAC6 Enterprise 카드 커넥터 5 iDRAC6 Express iDRAC6 Express 카드 커넥터 6 CPU 프로세서 소켓 7 FAN1 시스템 팬 1 커넥터 8 FAN2 시스템 팬 2 커넥터 9 FAN3 시스템 팬 3 커넥터 10 5 메모리 모듈 슬롯 5 3 메모리 모듈 슬롯 3 1 메모리 모듈 슬롯 1 (흰색 분리 레버) 6 메모리 모듈 슬롯 6 4 메모리 모듈 슬롯 4 2 메모리 모듈 슬롯 2 (흰색 분리 레버) 11 12V 4핀 전원 커넥터 12 PWR_CONN 24핀 전원 커넥터 13 CTRL_PNL 제어판 커넥터 14 SATA_A SATA 커넥터 A 15 SATA_B
잊어버린 암호 비활성화 시스템의 소프트웨어 보안 기능에는 53페이지의 "시스템 설치 프로그램 및 UEFI 부팅 관리자 사용"에 자세히 설명되어 있는 시스템 암호 및 설치 암호가 포함되어 있습니다. 암호 점퍼는 이러한 암호 기능을 활성화하거 나 비활성화하며 현재 사용 중인 모든 암호를 지웁니다. 주의: "정전기 방전 방지"는 시스템과 함께 제공된 안전 지침을 참조하십시오. 1 시스템 및 시스템에 연결된 모든 주변 장치의 전원을 끄고 전원 콘센트 에서 시스템을 분리합니다. 2 시스템을 엽니다. 78페이지의 "시스템 열기"를 참조하십시오. 3 암호 점퍼에서 점퍼 플러그를 분리합니다. 시스템 보드에서 암호 점퍼 ("PWRD_EN"이라고 표시됨) 를 찾으려면 그림 6-1을 참조하십시오. 4 시스템을 닫습니다. 79페이지의 "시스템 닫기"를 참조하십시오. 5 시스템 및 주변 장치를 전원 콘센트에 다시 연결하고 시스템을 켭니다.
도움말 얻기 Dell에 문의하기 미국에 거주하는 고객은 800-WWW-DELL (800-999-3355) 로 전화하십시오. 주: 인터넷 연결을 사용할 수 없는 경우에는 구매 송장, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다. Dell은 다양한 온라인 및 전화 기반의 지원과 서비스 옵션을 제공합니다. 제공 여부는 국가/지역과 제품에 따라 차이가 있으며 일부 서비스는 소재 지역에서 사용하지 못할 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문 제에 대해 Dell에 문의하려면 다음을 수행하십시오. 1 support.dell.com을 방문합니다. 2 페이지 아래쪽의 Choose A Country/Region (국가/지역 선택) 드롭다운 메뉴에서 소재 국가 또는 지역이 있는지 확인합니다. 3 페이지 왼쪽에서 Contact Us (문의처) 를 클릭합니다. 4 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다. 5 Dell에 문의하는 데 편리한 방법을 선택합니다.
도움말 얻기
색인 B L BMC 구성, 73 LCD 패널 기능, 14 메뉴, 16 C CD 드라이브 문제 해결, 150 N CD/DVD 드라이브 광학 드라이브 참조. NIC 문제 해결, 141 표시등, 21 D P Dell 문의하기, 163 Dell에 문의하기, 163 DIMM 메모리 모듈(DIMM) 참조. I iDRAC 구성 유틸리티, 74 iDRAC6 Enterprise 카드, 114 iDRAC6 Express 카드, 111 POST 시스템 기능 액세스, 11 S SAS 컨트롤러 카드 분리, 102 설치, 103 SAS 하드 드라이브. 하드 드라이 브 참조. SAS 후면판 보드 분리, 131 설치, 133 SATA 하드 드라이브. 하드 드라 이브 참조.
T ㄴ TPM 보안, 64 냉각 팬, 109 문제 해결, 146 장착, 111 U UEFI 부팅 관리자 System Utilities (시스템 유틸리티) 화면, 68 기본 화면, 67 시작, 66 UEFI 부팅 관리자 화면, 67 USB 장치 후면 패널 커넥터, 19 USB 키 문제 해결, 149 V VFlash 매체, 117 ㄱ 경고 메시지, 51 광학 드라이브 설치, 80 166 색인 냉각기 덮개 분리, 100 설치, 101 ㄷ 덮개 닫기, 79 열기, 78 드라이브 보호물 분리, 83 설치, 84 ㅁ 메모리 문제 해결, 147 메모리 모듈(DIMM) 구성, 104 분리, 108 설치, 106 메시지 경고, 51 상태 LCD, 25 시스템, 38 오류 메시지, 54
문제 해결, 149 CD 드라이브, 150 NIC, 141 내부 USB 키, 149 냉각 팬, 146 메모리, 147 비디오, 140 손상된 시스템, 143 습식 시스템, 142 시스템 냉각, 145 외부 연결, 139 전원 공급 장치, 145 키보드, 140 테이프 드라이브, 151 프로세서, 154 하드 드라이브, 152 확장 카드, 153 ㅂ 분리 SAS 컨트롤러, 102 SAS 후면판 보드, 131 냉각기 덮개, 100 덮개, 78 메모리 모듈, 108 베젤, 77 시스템 보드, 136 전원 공급 장치, 122, 125 전원 공급 장치 보호물, 124 제어판 조립품, 129 프로세서, 117, 121 하드 드라이브 보호물, 83 하드 드라이브 (케이블 연결됨), 87 하드 드라이브 (핫 플러그 가능), 84 확장 카드, 95 비디오 문제 해결, 140 방열판, 119 베젤, 77 보안, 139 보호물 전원 공급 장치, 124 하드 드라이브, 83 색인 167
ㅅ 섀시 침입 스위치, 76 설치 SAS 컨트롤러, 103 SAS 후면판 보드, 133 광학 드라이브, 80 냉각기 덮개, 101 메모리 모듈, 106 시스템 보드, 136 전원 공급 장치 보호물, 124 프로세서, 121 하드 드라이브 보호물, 84 하드 드라이브 (케이블 연결됨), 88 하드 드라이브 (핫 플러그 가능), 85 확장 카드, 93 확장 카드 라이저, 98 설치 암호, 71 손상된 시스템 문제 해결, 143 슬롯 확장 슬롯 참조.
ㅇ 암호 비활성화, 162 설치, 71 시스템, 69 업그레이드 프로세서, 117 오류 메시지, 54 옵션 시스템 설치 프로그램, 55 지원 Dell에 문의하기, 163 지침 메모리 설치, 104 외부 장치 연결, 21 확장 카드 설치, 91 진단 프로그램 고급 검사 옵션, 157 사용 시기, 156 ㅋ ㅈ 장착 냉각 팬, 111 시스템 전지, 127 전원 공급 장치, 124, 126 전면 패널 기능 및 표시등, 12 전원 공급 장치 문제 해결, 145 분리, 122, 125 장착, 124, 126 표시등, 22 전원 공급 장치 보호물, 124 전원 표시등, 22 전지(시스템) 장착, 127 전화 번호, 163 점퍼(시스템 보드), 159 제어판 조립품 LCD 패널 기능, 14 분리, 129 케이블 연결 광학 드라이브, 80 키보드 문제 해결, 140 ㅌ 테이프 드라이브 문제 해결, 151 ㅍ 표시등 NIC, 21 전원, 22 후면 패널, 19 프로세서 문제 해결, 154 분리, 117, 121
ㅎ 하드 드라이브 문제 해결, 152 하드 드라이브(케이블 연결됨) 분리, 87 설치, 88 하드 드라이브(핫 플러그 가능) 분리, 84 설치, 85 확장 슬롯, 91 확장 카드 SAS 컨트롤러, 102 문제 해결, 153 분리, 95 설치, 93 후면 패널 기능 및 표시등, 19 170 색인