Dell™ PowerEdge™ R410-Systeme HardwareBenutzerhandbuch
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie das System besser einsetzen können. VORSICHTSHINWEIS: Durch VORSICHTSHINWEISE werden Sie auf potenzielle Gefahrenquellen hingewiesen, die Hardwareschäden oder Datenverlust zur Folge haben könnten, wenn die Anweisungen nicht befolgt werden.
Inhalt 1 Wissenswertes zum System . . . . . . . . . . . Zugriff auf Systemfunktionen beim Start . . . . . . . . . Merkmale und Anzeigen auf der Vorderseite . 10 . . . . . . . . 13 . . . . . . . . . . . . . . . 17 Anzeigen und Merkmale auf der Rückseite . . . . . . . 18 . . . . . . . . . . 20 . . . . . . . . . . . . . . . . . . . 20 Richtlinien für das Anschließen von optionalen externen Geräten . . . . NIC-Anzeigecodes . 9 . . . . .
2 Verwenden des System-Setup -Programms und des UEFI-Boot-Managers . . . . . . . Auswahl des Systemstartmodus . . . . . . . . . 63 . . . . . . . . . . . . 63 Aufrufen des System-Setup-Programms . . . . . . . . . 64 Optionen des System-Setup-Programms . . . . . . . . 66 . . . . . . . . . . . 79 Aufrufen des UEFI-Boot-Managers System- und Setup-Kennwortfunktionen . . . . . . . . 81 . . . . . . . . . . . . . 86 . . . . . . . . . . . . . . . . 87 Integrierte Systemverwaltung .
Erweiterungskarten-Riser . Interner USB-Speicherstick . 114 . . . . . . . . . . . . . . Kühlgehäuse der Systemplatine . 115 . . . . . . . . . . . . Integrated Dell Remote Access Controller 6 (iDRAC6) Express-Karte (optional) . . . . . . . . . . . 117 Integrated Dell Remote Access Controller 6 (iDRAC6) Enterprise-Karte (optional) . . . . . . . . . . 119 . . . . . . . . . . . . . . . 122 . . . . . . . . . . . . . . . . . . . . . . . . . . 123 VFlash-Medium (optional) . Lüfter .
Fehlerbehebung bei externen Verbindungen . . . . . 160 . . . . . . . 160 . . . . . . . . 160 Fehlerbehebung beim Grafiksubsystem . Fehlerbehebung bei einem USB-Gerät Fehlerbehebung bei einem seriellen E/A-Gerät . Fehlerbehebung bei einem NIC . . . 161 . . . . . . . . . . . . 162 Fehlerbehebung bei Feuchtigkeit im System Fehlerbehebung bei einem beschädigten System . . . . . . . . 163 . . . . . . . . . . . . . . 164 Fehlerbehebung bei der Systembatterie . Fehlerbehebung bei Netzteilen . .
5 Ausführen der Systemdiagnose Verwenden von Dell™ Diagnostics . . . . . . . Ausführen der integrierten Systemdiagnose . . . 180 . . . . . . 180 Testoptionen der integrierten Systemdiagnose . 7 183 183 . . . . . . . . . . . . . . . Jumper auf der Systemplatine . . . . . 185 185 . . . . . . . . . . . . . Anschlüsse auf der Systemplatine 186 . . . . . . . . . . . Deaktivieren eines verlorenen Kennworts 188 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhalt
Wissenswertes zum System Zugriff auf Systemfunktionen beim Start Mit den folgenden Tastenkombinationen erhalten Sie beim Hochfahren Zugriff auf Systemfunktionen. Tastenkombination Beschreibung Aufruf des System-Setup-Programms. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 63. Aufruf von System Services und damit des Unified Server Configurators. Mit dem Unified Server Configurator haben Sie Zugriff auf Dienstprogramme wie die integrierte Systemdiagnose.
Merkmale und Anzeigen auf der Vorderseite Abbildung 1-1. Merkmale und Anzeigen auf der Vorderseite 8 9 7 6 1 2 3 4 5 Element Anzeige, Taste oder Anschluss 1 Symbol Betriebsanzeige, Netzschalter 10 Beschreibung Die Betriebsanzeige leuchtet, wenn das System eingeschaltet ist. Über den Netzschalter wird die Gleichstromversorgung des Systems gesteuert. Bei installierter optionaler Frontverkleidung ist der Netzschalter nicht zugänglich.
Element Anzeige, Taste oder Anschluss 2 NMI-Taste Symbol Beschreibung Dient dazu, Softwareprobleme und Fehler von Gerätetreibern zu beheben, wenn bestimmte Betriebssysteme verwendet werden. Sie können diese Taste mit einer aufgebogenen Büroklammer betätigen. Diese Taste sollte nur auf Anweisung eines zugelassenen Support-Mitarbeiters oder entsprechend der Dokumentation des Betriebssystems verwendet werden. 3 Monitoranschluss Zum Anschließen eines Bildschirms an das System.
Element Anzeige, Taste oder Anschluss 5 Symbol LED- oder LCD-Display Beschreibung ANMERKUNG: Je nach Konfiguration ist das System entweder mit LED-Diagnoseanzeigen oder einem LCD-Display ausgestattet. LED-Display: Die vier Diagnoseanzeigen dienen der Anzeige von Fehlercodes während des Systemstarts. Siehe „Diagnoseanzeigen (optional)“ auf Seite 22. LCD-Display: Zur Anzeige von Systemkennung, Statusinformationen und Systemfehlermeldungen. Das LCD-Display leuchtet während des normalen Systembetriebs.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 8 Festplatten (4) Bis zu vier 2,5-Zoll-Festplatten in 3,5-ZollHot-Swap-Trägern oder bis zu vier verkabelte/hot-swap-fähige 3,5-ZollFestplatten. 9 Systemidentifikationsfeld Ein herausziehbares Feld für Systeminformationen wie ExpressServicenummer, MAC-Adresse des integrierten NICs und MAC-Adresse der iDRAC6-Enterprise-Karte. 10 Optisches Laufwerk (optional) Ein optionales SATA-DVD-ROM-Laufwerk oder DVD+/-RW-Laufwerk in Flachbauweise.
Abbildung 1-2. Merkmale des LCD-Bedienfelds 1 2 3 4 Element Tasten Beschreibung 1 Links Bewegt den Cursor schrittweise zurück. 2 Auswahl Wählt den vom Cursor markierten Menüeintrag aus. 3 Rechts Bewegt den Cursor schrittweise vor. Beim Durchlaufen einer Meldung: • Einmal drücken, um die Laufgeschwindigkeit zu erhöhen. • Erneut drücken zum Anhalten. • Noch einmal drücken, um zur StandardLaufgeschwindigkeit zurückzukehren. • Erneutes Drücken wiederholt den Zyklus.
Home-Bildschirm Auf dem Home-Bildschirm werden vom Benutzer konfigurierbare Informationen über das System angezeigt. Dieser Bildschirm wird beim normalen Systembetrieb angezeigt, wenn keine Status- oder Fehlermeldungen anstehen. Wenn sich das System im Standby-Modus befindet, erlischt die LCD-Hintergrundbeleuchtung nach fünf Minuten Inaktivität, wenn keine Fehlermeldungen anstehen. Um den Home-Bildschirm anzuzeigen, drücken Sie eine der drei Steuertasten (Auswahl, Links oder Rechts).
Menü View Option Beschreibung BMC IP oder DRAC IP Anzeige der IPv4- oder IPv6-Adressen für den optionalen ANMERKUNG: Wenn im iDRAC6. Die Optionen sind DNS (Primary und Secondary), Gateway, IP und Subnet (kein Subnet System eine iDRAC6 bei IPv6). Express-Karte installiert ist, wird die BMC IP-Option ANMERKUNG: BMC IP unterstützt nur IPv4-Adressen. durch DRAC IP ersetzt. Anzeige der MAC-Adressen für DRAC, iSCSIn oder NETn.
Festplatten-Statusanzeigen Abbildung 1-3. Festplattenanzeigen 2 1 1 Laufwerkaktivitätsanzeige (grün) 2 Laufwerkstatusanzeige (grün und gelb) Laufwerkstatusanzeigemuster (nur RAID) Zustand Blinkt grün, zweimal pro Sekunde Laufwerk identifizieren/zum Entfernen vorbereiten Aus Laufwerk bereit zum Ein- oder Ausbauen ANMERKUNG: Die Laufwerkstatusanzeige bleibt ausgeschaltet, bis alle Festplatten nach dem Einschalten des Systems initialisiert sind.
Laufwerkstatusanzeigemuster (nur RAID) Zustand Blinkt gelb, viermal pro Sekunde Laufwerk ausgefallen Blinkt langsam grün Laufwerk wird neu aufgebaut Stetig grün leuchtend Laufwerk online Blinkt drei Sekunden grün, drei Sekunden Wiederaufbau abgebrochen gelb und ist sechs Sekunden aus. Anzeigen und Merkmale auf der Rückseite Abbildung 1-4 zeigt die Bedienelemente, Anzeigen und Anschlüsse auf der Systemrückseite. Abbildung 1-4.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 6 Ethernet-Anschlüsse (2) Integrierte 10/100/1000 NICAnschlüsse. 7 PCIe-Steckplatz 1 PCI Express-Erweiterungssteckplatz (2. Generation) mit x16-Bandbreite (volle Bauhöhe, halbe Baulänge) 8 Anschluss Active ID CMA Zum Anschließen eines Systemanzeigeverlängerungskabels, das bei einem Kabelführungsarm verwendet wird. 9 Systemstatusanzeige Leuchtet blau beim normalen Systembetrieb.
Richtlinien für das Anschließen von optionalen externen Geräten • Schalten Sie die Stromversorgung des Systems und der externen Geräte aus, bevor Sie ein neues externes Gerät anschließen. Schalten Sie zuerst alle externen Geräte ein, bevor Sie das System einschalten (es sei denn, die Gerätedokumentation gibt etwas anderes an). • Stellen Sie sicher, dass ein geeigneter Treiber für das angeschlossene Gerät auf dem System installiert wurde.
Anzeigecodes für Stromversorgung Eine LED am Netzschalter zeigt an, wenn das System mit Strom versorgt wird und in Betrieb ist. Eine Anzeige am jeweiligen Netzteil informiert darüber, ob Strom vorhanden oder ein Stromausfall aufgetreten ist. • Leuchtet nicht – Wechselstrom ist nicht angeschlossen. • Grün – Zeigt im Standby-Zustand an, dass eine zulässige Wechselstromquelle mit dem Netzteil verbunden und das Netzteil in Betrieb ist.
Diagnoseanzeigen (optional) Die vier Diagnoseanzeigen auf der Vorderseite geben Fehlercodes beim Systemstart wieder. Tabelle 1-1 enthält Ursachen und mögliche Behebungsmaßnahmen für diese Codes. Ein ausgefüllter Kreis bedeutet, dass die Anzeige leuchtet; ein leerer Kreis bedeutet, dass die Anzeige nicht leuchtet. ANMERKUNG: Die Diagnose-LEDs sind nicht vorhanden, wenn das System mit einem LCD-Display ausgestattet ist. Tabelle 1-1.
Tabelle 1-1. Diagnoseanzeigecodes (optional) (fortgesetzt) Code Ursachen Maßnahme Möglicher Erweiterungskartenfehler. Siehe „Fehlerbehebung bei Erweiterungskarten“ auf Seite 175. Möglicher Grafikfehler. Siehe „Wie Sie Hilfe bekommen“ auf Seite 183. Festplattenfehler. Stellen Sie sicher, dass das Diskettenlaufwerk und die Festplatte korrekt angeschlossen sind. Informationen zu den im System installierten Laufwerken finden Sie unter „Festplattenlaufwerke“ auf Seite 94. Möglicher USB-Fehler.
Tabelle 1-1. Diagnoseanzeigecodes (optional) (fortgesetzt) Code Ursachen Maßnahme Anderer Fehler. Stellen Sie sicher, dass das Diskettenlaufwerk, das optische Laufwerk und die Festplatte korrekt angeschlossen sind. Informationen zu den entsprechenden Laufwerken finden Sie unter „Fehlerbehebung beim System“ auf Seite 159. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183.
Tabelle 1-2. LCD-Statusmeldungen (optional) Code Text Ursachen Korrekturmaßnahmen - SYSTEM NAME Eine 62-stellige Zeichenkette, die im SystemSetup-Programm definiert werden kann. Diese Meldung dient ausschließlich zur Information. Sie können die System-ID SYSTEM NAME wird unter und den Namen im den folgenden Bedingungen System-Setup-Programm angezeigt: ändern. Siehe „Verwenden des System-Setup• Das System ist Programms und des UEFIeingeschaltet. Boot-Managers“ auf • Die Stromzufuhr ist Seite 63.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen Speicher hat den zulässigen Temperaturbereich überschritten und wurde deaktiviert, um die Komponenten vor Beschädigung zu schützen. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. E1210 Motherboard battery failure. Check battery. CMOS-Batterie nicht vorhanden, oder die Spannung ist außerhalb des zulässigen Bereichs.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text E1229 CPU # VCORE Regulator failure. Reseat CPU. Ursachen Korrekturmaßnahmen Der Spannungsregler für Setzen Sie den/die den angegebenen Prozessor Prozessor(en) neu ein. VCORE ist ausgefallen. Siehe „Fehlerbehebung bei den Mikroprozessoren“ auf Seite 176. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E122A CPU # VTT Regulator failure. Reseat CPU.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text E122E On-board regulator failed. Call support. Ursachen Korrekturmaßnahmen Einer der eingebauten Spannungsregler ist ausgefallen. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E1310 Fan ## RPM exceeding range. Check fan. RPM des angegebenen Lüfters ist außerhalb des angestrebten Betriebsbereichs.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1414 CPU # temp exceeding range. Check CPU heatsink. Der angegebene Prozessor befindet sich außerhalb des zulässigen Temperaturbereichs. Stellen Sie sicher, dass die Prozessorkühlkörper ordnungsgemäß installiert sind. Siehe „Fehlerbehebung bei den Mikroprozessoren“ auf Seite 176 und „Fehlerbehebung bei der Systemkühlung“ auf Seite 166. E1418 CPU # not detected. Check CPU is seated properly.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1420 CPU Bus parity Das System-BIOS hat einen Trennen Sie das System error. Power Prozessor-Busparitätsfehler für 10 Sekunden von cycle AC. gemeldet. der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E1422 CPU # machine check error. Power cycle AC.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E161C Power Supply # (### W) lost AC power. Check PSU cables. Das angegebene Netzteil ist an das System angeschlossen, erhält jedoch keinen Wechselstrom mehr. Überprüfen Sie die Wechselstromquelle für das angegebene Netzteil. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Netzteilen“ auf Seite 166. E1620 Power Supply # (### W) AC power error. Check PSU cables.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen E1710 I/O channel Das System-BIOS hat einen check error. E/A-Kanalprüffehler Review & clear gemeldet. SEL. Korrekturmaßnahmen Überprüfen Sie das SEL auf weitere Informationen und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E1714 Unknown error. Das System-BIOS hat einen Review & clear Systemfehler erkannt, kann SEL. aber nicht die Ursache feststellen. Überprüfen Sie das SEL auf weitere Informationen und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen E1A14 SAS cable A SAS-Kabel A ist nicht failure. Check vorhanden oder fehlerhaft. connection. Korrekturmaßnahmen Befestigen Sie das Kabel. Falls das Problem weiterhin besteht, tauschen Sie das Kabel aus. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E1A15 SAS cable B SAS-Kabel B ist nicht failure. Check vorhanden oder fehlerhaft. connection. Befestigen Sie das Kabel.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text E2011 Memory configuration failure. Check DIMMs. Ursachen Korrekturmaßnahmen Speicher wurde erkannt, lässt sich jedoch nicht konfigurieren. Bei der Speicherkonfiguration ist ein Fehler aufgetreten. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 167. E2012 Memory Speicher ist zwar configured but konfiguriert, aber nicht unusable. nutzbar. Check DIMMs. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 167.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen E2016 Interrupt Interrupt-Controllerfehler. Controller failure. Power cycle AC. Korrekturmaßnahmen Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E2017 Timer refresh Fehler bei der failure. Power Zeitgeberaktualisierung. cycle AC.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E201A SuperIO SIO-Fehler. failure. Power cycle AC. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E201B Keyboard Controller error. Power cycle AC. Fehler beim Tastaturcontroller. E201C SMI SMI-Initialisierungsfehler initialization (System Management failure.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text E201E POST memory test failure. Check DIMMs. Ursachen Korrekturmaßnahmen BIOS-POST-Speicherüber- Siehe „Fehlerbehebung prüfungsfehler. beim Systemspeicher“ auf Seite 167. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 183. E2020 CPU configuration failure. Check screen message. ProzessorKonfigurationsfehler. Auf dem Bildschirm werden spezifische Fehlermeldungen angezeigt.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen E2110 Multibit Error Am Speichermodul im on DIMM ##. Sockel „##“ ist ein MultiReseat DIMM. Bit-Fehler (MBE) aufgetreten. E2111 SBE log disabled on DIMM ##. Reseat DIMM. E2112 Memory spared on DIMM ##. Power cycle AC. E2113 Mem mirror OFF on DIMM ## & ##. Power cycle AC Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 167.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen I1910 Intrusion detected. Check chassis cover. Systemabdeckung wurde abgenommen. Dient nur zur Information. I1911 LCD Log Full. Check SEL to review all Errors. LCD-Überlaufmeldung. Auf dem LCD-Display können höchstens zehn Fehlermeldungen angezeigt werden. Die elfte Meldung fordert den Benutzer auf, im SEL nach Details zu den Ereignissen zu suchen.
Tabelle 1-2. LCD-Statusmeldungen (optional) (fortgesetzt) Code Text Ursachen Korrekturmaßnahmen W1627 Power required Die Systemkonfiguration > PSU wattage. benötigt mehr Strom als die Check PSU and Netzteile liefern können. config. Schalten Sie das System aus, entfernen Sie einige Hardwaregeräte oder installieren Sie Netzteile mit höherer Leistung, und starten Sie das System neu.
Entfernen von LCD-Statusmeldungen (optional) Bei Fehlern mit Sensoren, wie z. B. Temperatur, Spannung, Lüfter usw. wird die LCD-Meldung automatisch gelöscht, wenn der Sensor wieder in den Normalzustand zurückgekehrt ist. Wenn beispielsweise die Temperatur für ein Bauteil außerhalb des zulässigen Bereichs liegt, wird auf dem LCD-Display die entsprechende Fehlermeldung angezeigt; wenn die Temperatur dann wieder in den zulässigen Bereich zurückkehrt, wird die Meldung vom LCD-Display gelöscht.
Tabelle 1-3. Systemmeldungen Meldung Ursachen Korrekturmaßnahmen 128-bit Advanced ECC mode disabled. For 128-bit Advanced ECC, DIMMs must be installed in pairs. Pairs must be matched in size and geometry. Die Option Advanced ECC wurde im BIOS aktiviert, ist aber aufgrund einer nicht unterstützten Speicherkonfiguration nicht mehr gültig, möglicherweise weil ein Speichermodul fehlerhaft ist oder entfernt wurde. Die Einstellung Advanced ECC wurde deaktiviert.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Alert! iDRAC6 not responding. Power required may exceed PSU wattage. Der optionale iDRAC6 hat nicht mehr reagiert. Alert! Continuing system boot accepts the risk that system may power down without warning. Nach Wiederherstellen der Wechselstromversorgung benötigt der optionale iDRAC6 länger als normal für den Startvorgang. Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Alert! Power required exceeds PSU wattage. Check PSU and system configuration. Die Systemkonfiguration aus Prozessoren, Speichermodulen und Erweiterungskarten wird möglicherweise von den Netzteilen nicht unterstützt. Falls für Systemkomponenten gerade ein Upgrade erfolgt ist, versetzen Sie das System wieder in die vorherige Konfiguration zurück.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen BIOS MANUFACTURING MODE detected. MANUFACTURING MODE will be cleared before the next boot. System reboot required for normal operation. System befindet sich im Herstellermodus. Starten Sie das System neu, um den Herstellermodus zu beenden. BIOS Update Attempt Failed! Versuch zur RemoteAktualisierung des BIOS ist fehlgeschlagen. Wiederholen Sie die BIOSAktualisierung.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen CPU x installed with no memory. Speichermodule sind erforderlich, sind aber nicht in den Speichersockeln des angegebenen Prozessors installiert. Installieren Sie Speichermodule für den Prozessor. Siehe „Systemspeicher“ auf Seite 129. CPUs with different cache sizes detected. Im System wurden nicht übereinstimmende Prozessoren installiert.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Decreasing available memory. Fehlerhafte oder nicht ordnungsgemäß installierte Speichermodule. Setzen Sie die Speichermodule neu ein. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 167. DIMM configuration on each CPU should match. Unzulässige Speicherkonfiguration bei einem Zweiprozessorsystem. Die Speichermodulkonfiguration muss für jeden Prozessor identisch sein.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Invalid configuration information please run SETUP program. Eine unzulässige Systemkonfiguration hat zu einem Systemhalt geführt. Führen Sie das SystemSetup-Programm aus und überprüfen Sie die Einstellungen. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 63.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Maximum rank count exceeded. The following DIMM has been disabled: x Unzulässige Speicherkonfiguration erkannt. Das System funktioniert, aber das angegebene Speichermodul ist deaktiviert. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 129. Memory Initialization Warning: Memory size may be reduced.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Mirror mode disabled. For mirror mode, DIMMs must be installed in pairs. Pairs must be matched in size and geometry. Die Speicherkonfiguration entspricht nicht der Einstellung im BIOS. Die BIOS-Einstellung wurde deaktiviert. Konfigurieren Sie die Speichermodule neu für Memory Mirroring. Siehe „Systemspeicher“ auf Seite 129. No boot device available.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen No boot sector on Falsche Konfigurationseinstellungen im Systemhard drive. Setup-Programm oder kein Betriebssystem auf der Festplatte. Korrekturmaßnahmen Überprüfen Sie die Konfigurationseinstellungen des Festplattenlaufwerks im System-Setup-Programm. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 63. Installieren Sie gegebenenfalls das Betriebssystem auf der Festplatte.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Quad rank DIMM Unzulässige detected after Speicherkonfiguration single rank or erkannt. dual rank DIMM in socket. Read fault Requested sector not found. Das Betriebssystem kann vom Festplattenlaufwerk, dem optischen Laufwerk oder dem USB-Gerät nicht lesen, das System konnte einen bestimmten Sektor auf der Festplatte nicht finden, oder der angeforderte Sektor ist defekt.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Sector not found. Das Festplattenlaufwerk, USB-Gerät oder USBSeek error. Medium ist defekt. Seek operation failed. Korrekturmaßnahmen Ersetzen Sie das USBMedium oder das Gerät. Stellen Sie sicher, dass die USB- oder SASRückwandplatinenkabel korrekt angeschlossen sind.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen The following DIMMs should match in Unzulässige Speicherkonfiguration erkannt. Die angegebenen Speichermodule stimmen in Größe, Anzahl der Ranks oder Anzahl der DatenLanes nicht überein. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 129. Thermal sensor not detected on x.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Time-of-day not set - please run SETUP program. Die Einstellungen für Time oder Date sind falsch; fehlerhafte Systembatterie. Überprüfen Sie die Uhrzeitund Datumseinstellungen. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 63. Besteht das Problem weiterhin, ersetzen Sie die Systembatterie. Siehe „Systembatterie“ auf Seite 142. Timer chip Defekte Systemplatine. counter 2 failed.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Unable to launch System Services image. System halted! System wurde nach F10Tastendruck angehalten, weil das System Services-Image in der System-Firmware beschädigt ist oder aufgrund eines Systemplatinenaustauschs verloren ist. Starten Sie das System neu und aktualisieren Sie das Unified Server ConfiguratorRepository auf die neueste Software, um die volle Funktionalität wiederherzustellen.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Unsupported DIMM detected. The following DIMM has been disabled: x Unzulässige Speicherkonfiguration erkannt. Das System funktioniert, aber das angegebene Speichermodul ist deaktiviert. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 129. Unsupported memory configuration.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Warning: A fatal error has caused system reset! Please check the system event log! Ein schwerwiegender Systemfehler ist aufgetreten und führte zum Systemneustart. Überprüfen Sie das SEL auf Informationen, die während des Fehlers protokolliert wurden. Lesen Sie den entsprechenden Abschnitt zur Fehlerbehebung in „Fehlerbehebung beim System“ auf Seite 159 hinsichtlich fehlerhafter Komponenten, die im SEL auftauchen.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Warning! Power required exceeds PSU wattage. Check PSU and system configuration. Die Systemkonfiguration aus Prozessoren, Speichermodulen und Erweiterungskarten wird möglicherweise von den Netzteilen nicht unterstützt. Falls für Systemkomponenten gerade ein Upgrade erfolgt ist, versetzen Sie das System wieder in die vorherige Konfiguration zurück.
Tabelle 1-3. Systemmeldungen (fortgesetzt) Meldung Ursachen Korrekturmaßnahmen Write fault. Fehlerhaftes USB-Gerät, USBMedium, optisches Laufwerk, Festplattenlaufwerk oder Festplattensubsystem. Ersetzen Sie das USBMedium oder das Gerät. Stellen Sie sicher, dass die USB-, SASRückwandplatinen- oder SATA-Kabel korrekt angeschlossen sind.
Diagnosemeldungen Die Diagnoseprogramme des Systems geben eventuell Meldungen aus. Weitere Informationen zur Systemdiagnose finden Sie unter „Ausführen der integrierten Systemdiagnose“ auf Seite 180. Alarmmeldungen Die Systemverwaltungssoftware erzeugt Alarmmeldungen für das System. Alarmmeldungen bestehen aus Informations-, Status-, Warn- und Fehlermeldungen zu Laufwerks-, Temperatur-, Lüfter- und Stromversorgungsbedingungen.
Verwenden des System-SetupProgramms und des UEFI-BootManagers Das System-Setup-Programm ist das BIOS-Programm, mit dem Sie die Systemhardware verwalten und Optionen auf BIOS-Ebene festlegen können.
Der Boot-Modus wird im Feld Boot Mode des Bildschirms Boot Settings des System-Setup-Programm ausgewählt. Siehe Bildschirm „Boot Settings“ auf Seite 71. Wenn der Startmodus festgelegt ist, startet das System in diesem Modus, und danach können Sie mit der Installation des Betriebssystems in diesem Modus beginnen. Danach müssen Sie das System in demselben Startmodus (BIOS oder UEFI) starten, um auf das installierte Betriebssystem zuzugreifen.
Reaktion auf Fehlermeldungen Notieren Sie Fehlermeldungen, die während des Systemstarts angezeigt werden. In Systemmeldungen auf Seite 42 finden Sie eine Erläuterung dieser Meldung und Vorschläge zur Fehlerbehebung. ANMERKUNG: Es ist normal, wenn nach einem Speicher-Upgrade beim ersten Starten des Systems eine Meldung darüber angezeigt wird, dass sich die Speichergröße verändert hat.
Optionen des System-Setup-Programms Hauptbildschirm Abbildung 2-1. Hauptbildschirm des System-Setup-Programms ANMERKUNG: Welche Optionen angezeigt werden, hängt von der Konfiguration des Systems ab. ANMERKUNG: Die Standardeinstellungen des System-Setup-Programms sind in den folgenden Abschnitten gegebenenfalls bei den jeweiligen Optionen angegeben. Option Beschreibung System Time Stellt die Zeit der internen Systemuhr ein. System Date Stellt das Datum des internen Kalenders ein.
Option Beschreibung Processor Settings Zeigt Informationen zu den Mikroprozessoren an (Geschwindigkeit, Cache-Größe etc.) Siehe Bildschirm „Processor Settings“ auf Seite 69. SATA Settings Siehe Bildschirm „SATA Settings“ auf Seite 70. Boot Settings Siehe Bildschirm „Boot Settings“ auf Seite 71. Integrated Devices Siehe Bildschirm „Integrated Devices“ auf Seite 72.
Option Beschreibung F1/F2 Prompt on Error (Standardeinstellung Enabled) Ermöglicht dem System, bei Fehlern während des POST anzuhalten, sodass der Benutzer Gelegenheit hat, Ereignisse zu beobachten, die während eines normalen POST unbemerkt durchlaufen. Sie können mit F1 fortsetzen oder mit F2 das System-Setup-Programm aufrufen. VORSICHTSHINWEIS: Wenn diese Option deaktiviert ist („Disabled“), hält das System bei Fehlern während des POST nicht an.
Option Beschreibung Node Interleaving (Standardeinstellung Disabled) Bei der Einstellung Enabled wird Speicher-Interleaving unterstützt, wenn eine symmetrische Speicherkonfiguration installiert ist. Bei der Einstellung Disabled unterstützt das System asymmetrische Speicherkonfigurationen (NUMA = Non-Uniform Memory Architecture). Bildschirm „Processor Settings“ Option Beschreibung 64-bit Zeigt an, ob die Prozessoren 64-Bit-Erweiterungen unterstützen. Taktrate Zeigt die Prozessortaktrate an.
Option Beschreibung C States (Standardeinstellung Enabled) Bei der Einstellung Enabled können die Prozessoren in allen verfügbaren Leistungszuständen betrieben werden. Processor 1 Family -Model- Anzeige von Reihe, Modell und Stepping des angegebenen Stepping Prozessors. Bildschirm „SATA Settings“ Option Beschreibung Embedded SATA (Standardeinstellung ATA Mode) ATA Mode aktiviert den integrierten SATA-Controller. Off deaktiviert den Controller.
Bildschirm „Boot Settings“ Option Boot Mode (Standardeinstellung BIOS) Beschreibung VORSICHTSHINWEIS: Das Ändern des Boot-Modus kann dazu führen, dass das System nicht mehr startet, falls das Betriebssystem nicht im gleichen BootModus installiert wurde. Wenn das Betriebssystem Unified Extensible Firmware Interface unterstützt, können Sie diese Option auf UEFI setzen. Bei der Einstellung BIOS ist die Kompatibilität mit Betriebssystemen, die UEFI nicht unterstützen, gewährleistet.
Bildschirm „Integrated Devices“ Option Beschreibung Integrated SAS/RAID Controller (Standardeinstellung Enabled) Aktiviert oder deaktiviert den integrierten Speichercontroller. User Accessible USB Ports (Standardeinstellung All Ports On) Aktiviert oder deaktiviert die benutzerzugänglichen USBAnschlüsse des Systems. Die Optionen sind All Ports On (Alle Anschlüsse aktiviert), Only Back Ports On (Nur hintere Anschlüsse aktiviert) und All Ports Off (Alle Anschlüsse deaktiviert).
Option Beschreibung I/OAT DMA Engine (Standardeinstellung Disabled) Aktiviert oder deaktiviert I/O Acceleration Technology (I/OAT). Diese Funktion sollte nur aktiviert werden, wenn I/OAT von Hardware und Software des Systems unterstützt wird. Embedded Video Controller (Standardeinstellung Enabled) Zeigt die Gesamtkapazität des Grafikspeichers im integrierten Grafikcontroller an.
Option Beschreibung External Serial Connector (Standardeinstellung Serial Device1) Legt fest, ob Serial Device 1, Serial Device 2 oder Remote Access Device auf den externen seriellen Anschluss zugreifen kann. Failsafe Baud Rate (Standardeinstellung 115200) Zeigt die Failsafe-Baudrate für die Konsolenumleitung an. Das BIOS versucht die Baudrate automatisch zu bestimmen. Diese Failsafe-Baudrate wird nur dann verwendet, wenn dieser Versuch fehlschlägt. Dieser Wert sollte nicht verändert werden.
Bildschirm „Power Management“ Option Beschreibung Power Management Optionen sind OS Control (Betriebssystemsteuerung), Active Power Controller (Aktive Energiesteuerung), Custom (Benutzerdefiniert) oder Maximum Performance (Maximale Leistung). Wenn Sie OS Control, Active Power Controller oder Maximum Performance auswählen, werden die anderen Optionen auf diesem Bildschirm vom BIOS vorkonfiguriert. Wenn Sie Custom (Benutzerdefiniert) wählen, können Sie jede Option separat konfigurieren.
Bildschirm „System Security“ Option Beschreibung System Password (Systemkennwort) Zeigt den aktuellen Status der Kennwortsicherheitsfunktion an und ermöglicht die Zuweisung und Überprüfung eines neuen Systemkennworts. ANMERKUNG: Weitere Informationen finden Sie unter Verwenden des Systemkennworts auf Seite 81. Setup Password (SetupKennwort) Schränkt den Zugriff auf das System-Setup-Programm durch ein Setup-Kennwort ein.
Option Beschreibung TPM Activation (Standardeinstellung No Change) Bei der Einstellung Activate (Aktivieren) ist das TPM mit Standardeinstellungen aktiviert. Bei der Einstellung Deactivate (Deaktivieren) ist das TPM deaktiviert. Im Zustand No Change (Keine Änderung) wird keine Aktion veranlasst. Der Betriebszustand des TPM verbleibt unverändert (alle Benutzereinstellungen für das TPM bleiben erhalten). ANMERKUNG: Dieses Feld ist schreibgeschützt, wenn TPM Security auf Off eingestellt ist.
Option Beschreibung VORSICHTSHINWEIS: Löschen des TPM führt zum Verlust aller Schlüssel im TPM. Diese Option verhindert, dass das Betriebssystem gestartet werden kann und führt zu Datenverlusten, falls sich die Schlüssel nicht wiederherstellen lassen. Erstellen Sie unbedingt eine Sicherungskopie der TPM-Schlüssel, bevor Sie diese Option aktivieren. NMI Button (Standardeinstellung Disabled) Aktiviert oder deaktiviert die NMI-Funktion.
Aufrufen des UEFI-Boot-Managers ANMERKUNG: Damit ein Betriebssystem im UEFI-Modus installiert werden kann, muss es 64-Bit UEFI-kompatibel sein (zum Beispiel Microsoft® Windows Server® 2008 x64). DOS und 32-Bit-Betriebssysteme lassen sich nur im BIOS-Boot-Modus installieren. ANMERKUNG: Der Boot-Modus muss im System-Setup-Programm auf UEFI gesetzt sein, um den UEFI-Boot-Manager aufrufen zu können.
Bildschirm „UEFI Boot Manager“ Option Beschreibung Continue Das System versucht von den Geräten in der Startreihenfolge zu starten, beginnend mit dem ersten Eintrag. Wenn der Startvorgang fehlschlägt, setzt das Gerät den Vorgang mit dem nächsten Gerät in der Startreihenfolge fort, bis ein Startvorgang erfolgreich ist oder keine weiteren Startoptionen vorhanden sind. Zeigt die Liste der verfügbaren Startoptionen an (markiert mit Sternchen).
Bildschirm „System Utilities“ Option Beschreibung System Setup Ruft das System-Setup-Programm auf, ohne einen Neustart auszuführen. Systemdienste (USC) Startet das System neu und ruft den Unified Server Configurator auf, mit dem Sie Dienstprogramme wie die Systemdiagnose ausführen können. BIOS Boot Manager Ruft die Liste der Startoptionen auf BIOS-Ebene auf, ohne einen Neustart auszuführen.
Wenn ein Systemkennwort zugewiesen wurde, ist System Password (Systemkennwort) auf Enabled gesetzt. Wenn Password Status auf Unlocked gesetzt ist, können Sie das Systemkennwort ändern. Bei der Einstellung Locked können Sie das Systemkennwort nicht ändern. Durch das Deaktivieren des Kennworts mit dem entsprechenden Jumper auf der Systemplatine wird System Password (Systemkennwort) auf Disabled gesetzt, und Sie können das Systemkennwort nicht ändern oder neu eingeben.
6 Starten Sie entweder das System neu, um den Kennwortschutz wirksam werden zu lassen, oder setzen Sie Ihre Arbeit fort. ANMERKUNG: Der Kennwortschutz wird erst wirksam, wenn das System neu gestartet wird. Verwenden des Systemkennworts zur Systemsicherung ANMERKUNG: Wenn ein Setup-Kennwort vergeben wurde (siehe Verwenden des Setup-Kennworts auf Seite 84), wird das Setup-Kennwort als alternatives Systemkennwort zugelassen.
Deaktivieren des Systemkennworts Wenn das Systemkennwort bereits gesetzt ist, können Sie es deaktivieren, indem Sie das Kennwort während des POST eingeben und drücken, oder Sie können das System-Setup-Programm aufrufen und im Menü System Password zweimal die drücken. Ändern eines bestehenden Systemkennworts 1 Rufen Sie während des POST das System-Setup-Programm auf, indem Sie die Taste drücken. 2 Rufen Sie den Bildschirm System Security (Systemsicherheit) auf.
Wenn Sie das Kennwort bestätigen, wird die Option Setup Password (SetupKennwort) auf Enabled gesetzt. Beim nächsten Aufruf des System-SetupProgramms fordert Sie das System zur Eingabe des Setup-Kennworts auf. Eine Änderung der Option Setup Password (Setup-Kennwort) wird sofort wirksam (das System muss nicht neu gestartet werden).
Integrierte Systemverwaltung Der Unified Server Configurator (USC) ist ein integriertes Dienstprogramm, das System- und Speicherverwaltungsaufgaben aus einer eingebetteten Umgebung während des gesamten Lebenszyklus des Servers ermöglicht. Der USC lässt sich während des Startvorgangs aufrufen und unabhängig vom Betriebssystem verwenden. ANMERKUNG: Bestimmte Plattformkonfigurationen unterstützen möglicherweise nicht alle USC-Funktionen.
Baseboard-Management-Controller-Konfiguration ANMERKUNG: Wenn eine iDRAC6 Express-Karte im System installiet ist, wird das Dienstprogramm des Baseboard Management Controllers (BMC) durch das iDRAC 6-Dienstprogramm ersetzt. Mit dem BMC können Systeme per Fernzugriff konfiguriert, überwacht und wiederhergestellt werden.
iDRAC-Konfigurationsprogramm Das iDRAC-Konfigurationsprogramm ist eine VorstartKonfigurationsumgebung, die es ermöglicht, Parameter für den iDRAC6 und den verwalteten Server anzuzeigen und einzustellen. Mit dem iDRACKonfigurationsprogramm sind folgende Vorgänge möglich: • Konfigurieren, Aktivieren oder Deaktivieren des lokalen iDRAC6-Netzwerks (LAN) über den reservierten iDRAC6 Enterprise-Karten-Port oder die integrierten NICs. • Aktivieren oder Deaktivieren von IPMI über LAN.
Installieren von Systemkomponenten WARNUNG: Für das Bewegen oder den Transport des System wird empfohlen, das ursprüngliche Verpackungsmaterial von der Lieferung zu verwenden und/oder darauf zu achten, dass Beschädigungen durch Stoß oder Vibration vermieden werden. ANMERKUNG: Je nach Konfiguration ist das System mit fest verkabelten oder hot-swap-fähigen Festplattenlaufwerken, redundanten oder nicht-redundanten Netzteilen und einer LCD-Anzeige oder Diagnoseanzeigen ausgestattet.
Abbildung 3-1.
Entfernen und Anbringen der optionalen Frontverkleidung 1 Entriegeln Sie das Systemschloss am linken Rand der Frontverkleidung. 2 Heben Sie die Sperrklinke neben dem Schloss an. 3 Schwenken Sie die linke Seite der Frontverkleidung von der Vorderseite des Systems weg. 4 Lösen Sie die rechte Seite der Frontverkleidung aus dem Haken, und nehmen Sie die Frontverkleidung vom System ab. Abbildung 3-2.
Öffnen und Schließen des Systems WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. WARNUNG: Beim Anheben des Systems sollten Sie sich stets von jemand anders helfen lassen. Um Verletzungen zu vermeiden, sollten Sie nicht versuchen, das System allein zu bewegen.
Abbildung 3-3. Systemabdeckung entfernen und anbringen 1 2 1 Verriegelung 2 Vertiefung Schließen des Systems 1 Positionieren Sie die Abdeckung auf dem Gehäuse und versetzen Sie es leicht zur Systemrückseite, damit die zwei Haken an der hinteren Kante der Abdeckung über die entsprechenden Aussparungen an der hinteren Kante des Gehäuses greifen. Siehe Abbildung 3-3. 2 Schieben Sie die Abdeckung zur Gehäusevorderseite, bis sie einrastet.
Festplattenlaufwerke Das System unterstützt bis zu vier 3,5-Zoll-Festplatten (SAS oder SATA) oder 2,5-Zoll-Festplatten (SAS, SATA oder SSD) in hot-swap-fähigen 3,5-Zoll-Trägern oder als verkabelte Laufwerke. Abhängig vom Gehäuse werden die Festplatten intern installiert oder auf der Systemvorderseite (siehe Abbildung 3-1). Interne Festplattenlaufwerke werden an der Systemplatine oder einer optionalen Controllerkarte angeschlossen.
Installation eines Laufwerksplatzhalters Richten Sie den Festplattenplatzhalter mit dem Laufwerkschacht aus und führen Sie den Platzhalter in den Laufwerkschacht ein, bis die Sperrklinke einrastet. Siehe Abbildung 3-4. Entfernen eines Hot-Swap-Festplattenlaufwerks VORSICHTSHINWEIS: Stellen Sie sicher, dass das Betriebssystem Hot-SwapLaufwerkinstallation unterstützt. Informationen hierzu finden Sie in der Dokumentation zum Betriebssystem. 1 Entfernen Sie die Frontverkleidung.
Abbildung 3-5. Hot-swap-fähiges Festplattenlaufwerk entfernen und installieren 1 2 1 Entriegelungstaste 2 Bügel des Festplattenträgers Hot-swap-fähiges Festplattenlaufwerk installieren VORSICHTSHINWEIS: Verwenden Sie nur Laufwerke, die geprüft und für den Einsatz mit der SAS/SATA-Rückwandplatine zugelassen sind. VORSICHTSHINWEIS: Stellen Sie beim Installieren von Festplatten sicher, dass die angrenzenden Laufwerke vollständig installiert sind.
3 Installieren Sie das hot-swap-fähige Festplattenlaufwerk. a Drücken Sie die Taste auf der Vorderseite des Laufwerkträgers. b Schieben Sie den Laufwerkträger in den Schacht, bis der Träger die Rückwandplatine berührt. c Schließen Sie den Griff, um das Laufwerk zu verriegeln.Schieben Sie das Laufwerk bei geöffnetem Hebel des Festplattenträgers in den Schacht, bis der Träger die Rückwandplatine berührt (siehe Abbildung 3-5).
Installation einer Festplatte im Laufwerkträger 1 Führen Sie die Festplatte in den Laufwerkträger ein, wobei sich das Anschlussende des Laufwerks hinten befindet. Siehe Abbildung 3-6. 2 Richten Sie die Löcher in der Festplatte mit den hinteren Löchern am Laufwerkträger aus. Bei korrekter Ausrichtung schließt die Rückseite der Festplatte mit der Rückseite des Laufwerkträgers ab. 3 Befestigen Sie die vier Schrauben, um die Festplatte am Laufwerkträger zu sichern.
Abbildung 3-7. Verkabeltes Festplattenlaufwerk entfernen und installieren 2 1 3 4 1 Festplattenlaufwerk 2 Stromversorgungs-/Datenkabel 3 Zunge 4 Laufwerkhalterung ANMERKUNG: Wenn Sie das Festplattenlaufwerk nicht ersetzen, entfernen Sie es aus der Laufwerkhalterung (siehe Abbildung 3-8), und setzen Sie die leere Laufwerkhaltung dann wieder in den Schacht ein. 5 Bringen Sie die Systemabdeckung wieder an. Siehe „Schließen des Systems“ auf Seite 93.
Einsetzen eines verkabelten Festplattenlaufwerks WARNUNG: Nur zugelassene Servicetechniker dürfen die Gehäuseabdeckung entfernen und auf Komponenten im Innern des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Schalten Sie das System sowie die angeschlossenen Peripheriegeräte aus, und trennen Sie das System von der Steckdose und den Peripheriegeräten. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92.
Entfernen einer Festplatte aus einer Laufwerkhalterung Entfernen Sie die Schrauben von den Führungsschienen an der Laufwerkhalterung, und trennen Sie die Festplatte von der Halterung. Siehe Abbildung 3-8. Abbildung 3-8. Festplatte aus einer Laufwerkhalterung entfernen 1 2 3 4 1 Schrauben (4)* 2 Festplattenlaufwerk 3 SAS/SATA-Schraubloch 4 Laufwerkhalterung *Bei Dell bestellte Festplatten werden mit Schrauben geliefert.
Netzteile Das System unterstützt die folgenden Netzteilmodule: • 480 W (nicht-redundantes Netzteil) • 500 W (redundantes Netzteil) Wenn zwei Netzteile installiert sind, sorgt das zweite Netzteil für die hot-swapfähige Redundanz der Stromversorgung. In der redundanten Betriebsart wird die Stromlast auf beide Netzteile verteilt, um die Effizienz zu maximieren. Wenn ein Netzteil bei eingeschaltetem System entfernt wird, übernimmt das verbleibende Netzteil die gesamte Stromlast.
Abbildung 3-9. Redundantes Netzteil entfernen und einsetzen 1 2 3 1 Netzteil 3 Kabelhalteklammer 2 Verriegelung Installieren eines redundanten Netzteils 1 Stellen Sie sicher, dass beide Netzteile vom gleichen Typ sind und die gleiche maximale Ausgangsleistung haben. ANMERKUNG: Die maximale Leistungsabgabe (in Watt) ist auf dem Netzteiletikett angegeben. 2 Schieben Sie das neue Netzteil in das Gehäuse, bis das Netzteil vollständig eingesetzt ist und die Sperklinke einrastet. Siehe Abbildung 3-9.
Entfernen des Netzteilplatzhalters Wenn Sie ein zweites Netzteil installieren, entfernen Sie den Netzteilplatzhalter im Schacht PS2, indem Sie den Platzhalter herausziehen. VORSICHTSHINWEIS: Um eine ausreichende Kühlung des Systems zu gewährleisten, muss bei einer nicht-redundanten Konfiguration im Schacht PS2 ein Netzteilplatzhalter installiert sein. Entfernen Sie den Netzteilplatzhalter nur, wenn Sie ein zweites Netzteil installieren.
Abbildung 3-10.
Installieren eines nicht-redundanten Netzteils 1 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 2 Setzen Sie das Netzteil in das Gehäuse. Siehe Abbildung 3-10. Befestigen Sie die die Schraube, die das Netzteil am Gehäuse sichert. 3 Verbinden Sie alle Stromversorgungskabel mit der Systemplatine, den Festplatten und dem optischen Laufwerk. 4 Bringen Sie die Systemabdeckung wieder an. Siehe „Schließen des Systems“ auf Seite 93.
Tabelle 3-1. Reihenfolge bei der Installation von Erweiterungskarten Kartenpriorität Kartentyp Max.
5 Installieren Sie die Erweiterungskarte: a Fassen Sie die Erweiterungskarte an den Rändern an und platzieren Sie sie so, dass der Platinenstecker am Erweiterungskartensteckplatz auf dem Erweiterungskarten-Riser ausgerichtet ist. b Drücken Sie den Platinenstecker fest in den Erweiterungssteckplatz, bis die Karte vollständig eingesetzt ist. c Schließen Sie die Verriegelung für den Erweiterungskarten-Steckplatz. Siehe Abbildung 3-11. Abbildung 3-11.
Entfernen von Erweiterungskarten WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 3 Trennen Sie alle Kabel von der Karte.
Entfernen der integrierten Speichercontrollerkarte WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92.
Integrierte Speichercontrollerkarte installieren WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92.
Erweiterungskarten-Riser Der Erweiterungskarten-Riser des Systems unterstützt eine PCIeErweiterungskarte mit x16-Bandbreite der 1. oder 2. Generation. (Ein zusätzlicher Steckplatz auf dem Riser ist reserviert für die integrierte Speichercontrollerkarte.) Entfernen eines Erweiterungskarten-Risers WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen.
Abbildung 3-13.
Einsetzen eines Erweiterungskarten-Risers 1 Um einen Erweiterungskarten-Riser zu installieren, richten Sie die Riser-Platine mit den Führungsstiften auf der Systemplatine aus. Siehe Abbildung 3-13. 2 Senken Sie den Erweiterungskarten-Riser ab, bis der Stecker vollständig im Anschluss eingesetzt ist. 3 Installieren Sie gegebenenfalls die integrierte Speichercontrollerkarte. Siehe „Integrierte Speichercontrollerkarte installieren“ auf Seite 111. 4 Installieren Sie gegebenenfalls die Erweiterungskarte.
1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 3 Lokalisieren Sie den USB-Anschluss auf der Bedienfeldplatine. Siehe Abbildung 3-14. 4 Setzen Sie den USB-Speicherstick in den USB-Anschluss ein. 5 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93. 6 Verbinden Sie das System mit dem Netzstrom und starten Sie das System neu. Abbildung 3-14.
1 Öffnen Sie das System. Siehe „Öffnen und Schließen des Systems“ auf Seite 92. 2 Lokalisieren Sie die zwei Vorsprünge mit blauem Punkt zwischen den Lüfterbaugruppen. Siehe Abbildung 3-15. 3 Heben Sie das Kühlgehäuse an den Vorsprüngen vorsichtig und gerade nach oben von der Systemplatine ab. Siehe Abbildung 3-15. 4 Entfernen Sie das Kühlgehäuse der Systemplatine. Abbildung 3-15.
Installieren des Kühlgehäuses der Systemplatine 1 Richten Sie das Kühlgehäuse am Mittelpunkt der nummerierten Lüfterschächte aus und lokalisieren Sie den Vorsprung auf der linken Seite des Lüftermoduls 3. Siehe Abbildung 3-15. 2 Drücken Sie das Kühlgehäuse der Systemplatine nach unten, bis alle Haltezungen in den Schlitzen sitzen und das Kühlgehäuse an der Systemplatine sichern. 3 Schließen Sie das System. Siehe „Öffnen und Schließen des Systems“ auf Seite 92.
Abbildung 3-16. iDRAC6 Express-Karte (optional) installieren oder entfernen 2 1 3 4 1 iDRAC6 Express-Karte 2 Halterung 3 Klammer 4 Halterungssteg aus Kunststoff 4 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93. 5 Stellen Sie die Stromzufuhr zum System und zu den Peripheriegeräten wieder her und schalten Sie sowohl das System als auch die Geräte ein.
3 So entfernen Sie die iDRAC6 Express-Karte: a Ziehen Sie den Halterungssteg an der Vorderkante der Karte leicht zurück, und heben Sie Karte vorsichtig vom Halterungssteg ab. Siehe Abbildung 3-20. Beim Ablösen der Karte vom Steg wird der Stecker unter der Karte vom Anschluss auf der Systemplatine getrennt. b Winkeln Sie die Karte so an, dass die Halterung an der Karte sich aus der Klammer auf der Systemplatine lösen kann. 4 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93.
5 Setzen Sie die iDRAC6 Enterprise-Karte ein: a Winkeln Sie die Karte so an, dass der RJ-45-Anschluss durch die Öffnung auf der Rückseite passt. Siehe Abbildung 3-17. b Richten Sie die Vorderkante der Karte mit den zwei vorderen Haltestegen aus Kunststoff neben dem iDRAC6-Anschluss auf der Systemplatine aus, und senken Sie die Karte in die Einbauposition ab. Siehe Abbildung 3-17. Wenn die Vorderseite der Karte vollständig sitzt, rasten die zwei Halterungsstege über der Vorderkante der Karte ein.
6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93. 7 Stellen Sie die Stromzufuhr zum System und zu den Peripheriegeräten wieder her und schalten Sie sowohl das System als auch die Geräte ein. Entfernen einer iDRAC6 Enterprise-Karte WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen.
9 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93. 10 Stellen Sie die Stromzufuhr zum System und zu den Peripheriegeräten wieder her und schalten Sie sowohl das System als auch die Geräte ein. VFlash-Medium (optional) Die VFlash-Medienkarte ist eine SD-Karte (Secure Digital), die an der optionalen iDRAC6-Enterprise-Karte in der hinteren Ecke des Systems eingesetzt wird.
Lüfter Das System enthält vier doppelmotorige Lüfter für die Kühlung des Prozessors und der Speichermodule sowie zwei doppelmotorige Lüfter für die redundanten Netzteile. ANMERKUNG: Das Entfernen oder Installieren der Lüfter per Hot-Swap-Vorgang wird nicht unterstützt.
Abbildung 3-18. Lüfter entfernen und einsetzen 1 2 1 Lüfter 2 Stromversorgungskabel Austauschen eines Lüfters 1 Stellen Sie sicher, dass der Lüfter korrekt orientiert ist. Das Lüftermodul muss so ausgerichtet sein, dass die Seite mit dem Stromversorgungskabel zur Systemrückseite weist. 2 Schieben Sie das Lüftermodul in die Lüfterbaugruppe, bis der Lüfter vollständig eingesetzt ist. Siehe Abbildung 3-18.
Optisches Laufwerk Ein optionales optisches DVD- oder DVD-RW-Laufwerk in Flachbauweise ist von der Vorderseite zugänglich und mit dem SATA-Controller auf der Systemplatine verbunden. ANMERKUNG: DVD-Geräte sind reine Datenlaufwerke. Entfernen eines optischen Laufwerks WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen.
Abbildung 3-19.
Installation eines optischen Laufwerks WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Entfernen Sie gegebenenfalls die optionale Frontverkleidung. Siehe „Entfernen und Anbringen der optionalen Frontverkleidung“ auf Seite 91.
2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 3 Um das RAID-Akkukabel vom Anschluss auf der Systemplatine zu trennen, drücken Sie auf die Sperrklinke am RAID-Akkukabelstecker, und ziehen Sie den Kabelstecker vorsichtig vom Anschluss auf der Systemplatine ab. Siehe Abbildung 3-20. 4 Ziehen Sie die zwei Haltelaschen des RAID-Akkus vorsichtig nach hinten und heben Sie den RAID-Akku aus dem Halter heraus. Siehe Abbildung 3-20. Abbildung 3-20.
3 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 93. 4 Stellen Sie das System aufrecht auf eine flache, stabile Arbeitsfläche. 5 Schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. Systemspeicher Das System unterstützt registrierte DDR3-DIMMs (RDIMMs) oder ungepufferte ECC-DIMMs (UDIMMs). Einzel- und Dual-DIMMs können mit 1067 oder 1333 MHz getaktet sein und Vierfach-DIMMs mit 1067 MHz.
• Speichermodule unterschiedlicher Größe können in A1-A4 oder B1-B4 gemischt eingesetzt werden (zum Beispiel 2 GB und 4 GB), aber alle belegten Kanäle müssen identisch konfiguriert sein. • In der Betriebsart Optimizer werden die Speichermodule in der numerischen Reihenfolge der Sockel – beginnend mit A1 bzw. B1 – installiert.
Betriebsartspezifische Richtlinien Jedem Prozessor sind drei Speicherkanäle zugewiesen. Die Anzahl der verwendeten Kanäle und die zulässigen Konfigurationen sind von der ausgewählten Speicherbetriebsart abhängig. Unterstützung für Advanced ECC (Lockstep) Bei dieser Konfiguration werden die zwei dem Prozessor am nächsten liegenden Kanäle zu einem 128-Bit-Kanal kombiniert. Diese Betriebsart unterstützt SDDC (Single Device Data Correction) für x4- und x8-Speichermodule.
. Tabelle 3-2.
Tabelle 3-3.
1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 3 Entfernen Sie das Kühlgehäuse der Systemplatine. Siehe „Entfernen des Kühlgehäuses der Systemplatine“ auf Seite 115. 4 Suchen Sie die Speichermodulsockel. Siehe Abbildung 7-1.
7 Richten Sie den Stecker des Speichermoduls an den Abgleichmarkierungen des Speichermodulsockels aus, und setzen Sie das Speichermodul in den Sockel ein. ANMERKUNG: Die Passung im Speichermodulsockel sorgt dafür, dass die Speichermodule nicht verkehrt herum installiert werden können. 8 Drücken Sie das Speichermodul mit den Daumen nach unten und sichern Sie so das Modul im Sockel.
Entfernen von Speichermodulen WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. WARNUNG: Die Speichermodule sind auch nach dem Ausschalten des Systems eine Zeitlang zu heiß zum Anfassen. Lassen Sie die Speichermodule ausreichend lange abkühlen, bevor Sie sie berühren.
Prozessoren Entfernen eines Prozessors WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Laden Sie vor dem Upgrade des Systems die aktuelle Version des SystemBIOS von support.dell.com herunter. 2 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom.
Abbildung 3-22. Kühlkörper installieren und entfernen 2 1 1 Kühlkörperhalteschrauben (4) 2 Kühlkörper 10 Drehen Sie die Prozessorabdeckung nach oben und zur Seite. Siehe Abbildung 3-23. 11 Heben Sie den Prozessor aus dem Sockel und belassen Sie den Hebel in senkrechter Position, damit der neue Prozessor in den Sockel eingepasst werden kann.
VORSICHTSHINWEIS: Achten Sie darauf, keine Kontaktstifte am ZIF-Sockel zu verbiegen, wenn Sie den Prozessor entfernen. Durch ein Verbiegen der Kontaktstifte kann die Systemplatine dauerhaft beschädigt werden. Wenn Sie einen Prozessor dauerhaft vom Sockel CPU2 entfernen, müssen Sie einen Prozessorplatzhalter und einen Kühlkörperplatzhalter installieren, um eine ordnungsgemäße Systemkühlung zu gewährleisten. Das Einsetzen von Platzhaltern und Prozessoren erfolgt auf ähnliche Weise.
Installieren eines Prozessors WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Laden Sie vor einem Upgrade der Prozessoren und des Systems die aktuelle Version des System-BIOS von support.dell.com herunter und installieren Sie es.
VORSICHTSHINWEIS: Wenden Sie beim Einsetzen des Prozessors keine Kraft an. Wenn der Prozessor korrekt positioniert ist, lässt er sich leicht in den Sockel einsetzen. b Schließen Sie die Prozessorabdeckung. c Schwenken Sie den Freigabehebel nach unten, bis er einrastet. 6 Installieren Sie den Kühlkörper. a Entfernen Sie die Wärmeleitpaste mit einem sauberen, fusselfreien Tuch vom Kühlkörper.
Systembatterie Austauschen der Systembatterie WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. WARNUNG: Bei falschem Einbau einer neuen Batterie besteht Explosionsgefahr. Tauschen Sie die Batterie nur gegen eine Batterie desselben oder eines gleichwertigen, vom Hersteller empfohlenen Typs aus.
Abbildung 3-24. Systembatterie austauschen 2 1 3 1 Positive Seite des Batteriesockels 3 Negative Seite des Batteriesockels 2 Systembatterie 4 Lokalisieren Sie den Batteriesockel. Siehe „Jumper, Schalter und Anschlüsse“ auf Seite 185. VORSICHTSHINWEIS: Um Beschädigungen am Batteriesockel zu vermeiden, müssen Sie den Sockel fest unterstützen, wenn Sie eine Batterie installieren oder entfernen. 5 Entfernen Sie die Systembatterie.
6 Installieren Sie die neue Systembatterie. a Unterstützen Sie den Batteriesockel, indem Sie fest auf die positive Seite des Sockels drücken. b Halten Sie die Batterie mit der Seite „+“ in Richtung des Kunststoffanschluss auf der Systemplatine und führen Sie sie in den Sockel ein. c Drücken Sie die Batterie gerade nach unten in den Sockel, bis sie einrastet. 7 Installieren Sie das Kühlgehäuse für die Systemplatine. Siehe „Installieren des Kühlgehäuses der Systemplatine“ auf Seite 117.
1 Entfernen Sie gegebenenfalls die optionale Frontverkleidung. Siehe „Entfernen und Anbringen der optionalen Frontverkleidung“ auf Seite 91. 2 Schalten Sie das System sowie die angeschlossenen Peripheriegeräte aus, und trennen Sie das System von der Netzstromsteckdose und den Peripheriegeräten. 3 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. 4 Trennen Sie das Schnittstellenkabel des Bedienfelds von der Bedienfeldplatine. • Das LED-Bedienfeld ist in Abbildung 3-25 dargestellt.
Abbildung 3-25.
Abbildung 3-26.
Installieren der Bedienfeldbaugruppe 1 Fahren Sie im Fall des LED-Bedienfelds mit Schritt 3 fort. Setzen Sie das Displaymodul in die Aussparung im Gehäuse ein und befestigen Sie sie mit den zwei Schrauben. 2 Befestigen Sie das Ersatzbauteil an der Vorderseite des Displaymoduls. 3 Richten Sie die Aussparung in der Bedienfeldplatine mit dem Steg am Systemgehäuse aus und befestigen Sie die Platine mit den zwei Kreuzschlitzschrauben. Siehe Abbildung 3-26. Übergehen Sie im Fall des LED-Bedienfelds den Schritt 4.
3 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 92. VORSICHTSHINWEIS: Um Schäden an den Laufwerken und der Rückwandplatine zu vermeiden, müssen Sie die Festplatten aus dem System entfernen, bevor Sie die Rückwandplatine entfernen. VORSICHTSHINWEIS: Die Nummern der einzelnen Festplatten müssen notiert und vor dem Entfernen auf den Festplatten vermerkt werden, damit sie an den gleichen Positionen wieder eingesetzt werden können. 4 Entfernen Sie alle Festplatten.
Abbildung 3-27.
Installieren der SAS-Rückwandplatine 1 Installieren Sie die SAS-Rückwandplatine: a Senken Sie die Rückwandplatine in das System ab, wobei Sie sorgfältig darauf achten, dass keine Komponenten auf der Platine beschädigt werden. b Richten Sie die Schlitze in der Rückwandplatine mit den Halterungen auf der Rückseite der Laufwerkschächte aus, und bewegen Sie die Rückwandplatine nach vorn, so dass die Halterungen in die Schlitze der Rückwandplatine eingreifen. Siehe Abbildung 3-27.
3 Trennen Sie die Kabel der Stromverteilerplatine von der Systemplatine (siehe „Systemplatine (nur für Service)“ auf Seite 154) und trennen Sie die Lüfterkabel an ihren Anschlüssen. Siehe Abbildung 3-28. 4 Entfernen Sie die zwei Schrauben, mit denen die Stromverteilerplatine am Gehäuse befestigt ist. Siehe Abbildung 3-28. 5 Schieben Sie die Stromverteilerplatine von den Stegen weg und heben Sie dann die Platine heraus. Siehe Abbildung 3-28. Abbildung 3-28.
Austauschen der Stromverteilerplatine WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Nehmen Sie die neue Stromverteilerplatine aus der Verpackung. 2 Richten Sie die Stromverteilerplatine mit den Stegen am Gehäuse aus und schieben Sie sie in die Einbauposition. Siehe Abbildung 3-28.
Systemplatine (nur für Service) Entfernen der Systemplatine WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen.
10 Entfernen Sie die Systemplatinenbaugruppe: a Entfernen Sie die neun Schrauben, mit denen die Systemplatine am Gehäuse befestigt ist, und schieben Sie dann die Systemplatinenbaugruppe in Richtung Gehäusevorderseite. VORSICHTSHINWEIS: Fassen Sie die Systemplatinenbaugruppe nicht an einem Speichermodul, einem Prozessor oder anderen Komponenten an. b Fassen Sie die Systemplatinenbaugruppe an den Rändern der Systemplatine an und heben Sie die Baugruppe aus dem Gehäuse. Siehe Abbildung 3-29.
Installation der Systemplatine 1 Nehmen Sie die neue Systemplatine aus der Verpackung. 2 Entfernen Sie die Etiketten von der Prozessorabdeckung und befestigen Sie sie am Systemidentifikationsfeld auf der Systemvorderseite. Siehe Abbildung 1-1. 3 Übertragen Sie die Prozessoren auf die neue Systemplatine. Siehe „Entfernen eines Prozessors“ auf Seite 137 und „Installieren eines Prozessors“ auf Seite 140.
6 Schließen Sie die Kabel in der nachstehend aufgeführten Reihenfolge an (die Positionen der Anschlüsse auf der Systemplatine sind in Abbildung 7-1 dargestellt): • SATA-Schnittstellenkabel, falls zutreffend • Schnittstellenkabel für Bedienfeld • Stromversorgungsanschluss für optisches Laufwerk • USB-Schnittstellenanschluss für Bedienfeld • Stromversorgungsanschluss für SAS-Rückwandplatine • Stromversorgungsanschlüsse der Systemplatine 7 Setzen Sie die Erweiterungskarten-Riser wieder ein.
Installieren von Systemkomponenten
Fehlerbehebung beim System Sicherheit geht vor – für Sie und Ihr System WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen.
Fehlerbehebung bei externen Verbindungen Stellen Sie sicher, dass alle externen Kabel fest mit den externen Anschlüssen des Systems verbunden sind, bevor Sie mit der Fehlerbehebung von externen Geräten beginnen. Die Anschlüsse auf der Vorder- und Rückseite des Systems sind in Abbildung 1-1 und Abbildung 1-4 dargestellt. Fehlerbehebung beim Grafiksubsystem 1 Überprüfen Sie die Systemanschlüsse und die Stromversorgung des Bildschirms.
c Tauschen Sie die Tastatur/Maus durch eine andere, funktionierende Tastatur/Maus aus. Wenn sich das Problem auf diese Weise lösen lässt, ersetzen Sie die defekte Tastatur/Maus. Wenn das Problem nicht gelöst wurde, fahren Sie mit dem nächsten Schritt fort und beginnen Sie mit der Fehlerbehebung der anderen USB-Geräte am System. 2 Schalten Sie alle angeschlossenen USB-Geräte aus und trennen Sie sie vom System.
3 Schalten Sie das System und das serielle Gerät aus und tauschen Sie das Gerät gegen ein vergleichbares Gerät aus. 4 Schalten Sie das System und das serielle Gerät wieder ein. Wenn das Problem dadurch behoben wird, muss das serielle Gerät ersetzt werden. Wenn das Problem weiterhin besteht, lesen Sie Wie Sie Hilfe bekommen auf Seite 183. Fehlerbehebung bei einem NIC 1 Führen Sie die entsprechende Online-Diagnose durch. Siehe Verwenden von Dell™ Diagnostics auf Seite 179.
6 Stellen Sie sicher, dass alle NICs, Hubs und Switches im Netzwerk auf die gleiche Datenübertragungsgeschwindigkeit eingestellt sind. Lesen Sie die Dokumentation zu den einzelnen Netzwerkgeräten. 7 Stellen Sie sicher, dass alle Netzwerkkabel vom richtigen Typ sind und die maximale Länge nicht überschreiten. Wenn alle Versuche zur Fehlerbehebung fehlschlagen, lesen Sie Wie Sie Hilfe bekommen auf Seite 183.
4 Lassen Sie das System gründlich trocknen (mindestens 24 Stunden). 5 Setzen Sie die in Schritt 3 entfernten Komponenten wieder ein. 6 Schließen Sie das System. Siehe Schließen des Systems auf Seite 93. 7 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und die angeschlossenen Peripheriegeräte ein. Wenn das System nicht ordnungsgemäß hochfährt, lesen Sie den Abschnitt Wie Sie Hilfe bekommen auf Seite 183.
3 Stellen Sie sicher, dass alle Kabel ordnungsgemäß angeschlossen sind. 4 Schließen Sie das System. Siehe Schließen des Systems auf Seite 93. 5 Starten Sie die Systemplatinen-Testgruppe in der Systemdiagnose. Siehe Ausführen der Systemdiagnose auf Seite 179. Wenn die Tests fehlschlagen, lesen Sie Wie Sie Hilfe bekommen auf Seite 183.
Fehlerbehebung bei Netzteilen 1 Identifizieren Sie das fehlerhafte Netzteil anhand der Fehleranzeige am Netzteil. Siehe Anzeigecodes für Stromversorgung auf Seite 21. VORSICHT: Um das System betreiben zu können, muss mindestens ein Netzteil installiert sein. Wenn das System über einen längeren Zeitraum mit nur einem Netzteil betrieben wird, kann dies eine Überhitzung zur Folge haben. 2 Setzen Sie die Netzteile neu ein, indem Sie sie entfernen und neu installieren. Siehe Netzteile auf Seite 102.
Fehlerbehebung bei einem Lüfter WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. 1 Lokalisieren Sie den defekten Lüfter, der auf dem LCD-Display oder in der Diagnosesoftware angezeigt wird. 2 Schalten Sie das System und alle angeschlossenen Peripheriegeräte aus. 3 Öffnen Sie das System.
2 Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System von der Netzstromversorgung. Drücken Sie bei getrenntem Netzstromkabel den Netzschalter, und verbinden Sie dann das System wieder mit der Netzstromversorgung. 3 Schalten Sie das System und die angeschlossenen Peripheriegeräte ein, und achten Sie auf die Meldungen auf dem Bildschirm. Wird ein Fehler bei einem bestimmten Speichermodul gemeldet, fahren Sie fort mit Schritt 12.
14 Wenn ein Diagnosetest oder eine Fehlermeldung ein bestimmtes Speichermodul als fehlerhaft ausweist, tauschen Sie das Modul gegen ein anderes, oder ersetzen Sie das Modul. 15 Um ein nicht bestimmtes defektes Speichermodul zu identifizieren, ersetzen Sie das Speichermodul im ersten DIMM-Sockel durch ein Modul des gleichen Typs und der gleichen Kapazität. Siehe Installieren von Speichermodulen auf Seite 133. 16 Schließen Sie das System. Siehe Schließen des Systems auf Seite 93.
8 Setzen Sie einen anderen USB-Stick ein, der nachweislich funktioniert. 9 Schließen Sie das System. Siehe Schließen des Systems auf Seite 93. 10 Schalten Sie das System und die angeschlossenen Peripheriegeräte ein und überprüfen Sie, ob der USB-Stick funktioniert. Fehlerbehebung bei einem optischen Laufwerk WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen.
Fehlerbehebung bei einem externen Bandlaufwerk 1 Verwenden Sie versuchsweise eine andere Bandkassette. 2 Stellen Sie sicher, dass die Gerätetreiber für das Bandlaufwerk installiert und korrekt konfiguriert sind. Weitere Informationen über Gerätetreiber erhalten Sie in der Dokumentation zum Bandlaufwerk. 3 Installieren Sie die Bandsicherungssoftware neu, wie in der zugehörigen Dokumentation beschrieben.
Fehlerbehebung bei einem Festplattenlaufwerk WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen. VORSICHT: Dieses Fehlerbehebungsverfahren kann die auf dem Festplattenlaufwerk gespeicherten Daten zerstören.
6 Überprüfen Sie die Kabelverbindungen im Inneren des Systems: a Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. b Öffnen Sie das System. Siehe Öffnen des Systems auf Seite 92. c Stellen Sie sicher, dass die Kabelverbindungen zwischen den Festplatten und dem Laufwerkcontroller korrekt hergestellt sind und die Kabel fest angeschlossen sind. d Schließen Sie das System. Siehe Schließen des Systems auf Seite 93.
4 Überprüfen Sie die Konfigurationseinstellungen, nehmen Sie gegebenenfalls erforderliche Korrekturen vor und starten Sie das System neu. 5 Entfernen Sie gegebenenfalls die optionale Frontverkleidung. Siehe Entfernen und Anbringen der optionalen Frontverkleidung auf Seite 91. WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen.
Fehlerbehebung bei Erweiterungskarten ANMERKUNG: Hinweise zur Lösung von Problemen mit Erweiterungskarten erhalten Sie in der Dokumentation zum Betriebssystem und zu der betreffenden Erweiterungskarte. WARNUNG: Nur ausgebildete Service-Techniker dürfen die Gehäuseabdeckung entfernen und auf die Komponenten im Inneren des Systems zugreifen. Lesen Sie die Sicherheitshinweise, die Sie mit dem System erhalten haben, bevor Sie mit dem Ein- oder Ausbau beginnen.
14 Führen Sie für jede Erweiterungskarte, die Sie in Schritt 10 entfernt haben, folgende Schritte durch: a Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Netzstrom. b Öffnen Sie das System. Siehe Öffnen des Systems auf Seite 92. c Installieren Sie eine der Erweiterungskarten neu. d Schließen Sie das System. Siehe Schließen des Systems auf Seite 93. e Führen Sie den entsprechenden Diagnosetest durch.
8 Schalten Sie bei einem System mit mehreren Prozessoren das System und die angeschlossenen Peripheriegeräte aus, und trennen Sie das System vom Netzstrom. 9 Öffnen Sie das System. Siehe Öffnen des Systems auf Seite 92. 10 Entfernen Sie alle Prozessoren außer Prozessor 1. Siehe Entfernen eines Prozessors auf Seite 137. 11 Schließen Sie das System. Siehe Schließen des Systems auf Seite 93.
Fehlerbehebung beim System
Ausführen der Systemdiagnose Bei Problemen mit dem System sollten Sie eine Diagnose durchführen, bevor Sie technische Unterstützung anfordern. Der Zweck der Diagnose ist es, die Hardware des Systems ohne zusätzliche Ausrüstung und ohne das Risiko eines Datenverlusts zu überprüfen. Wenn Sie ein Problem nicht selbst beheben können, können Service- und Supportmitarbeiter die Diagnoseergebnisse zur Lösung des Problems verwenden.
Funktionen der integrierten Systemdiagnose Die integrierte Systemdiagnose enthält eine Reihe von Menüs und Optionen für bestimmte Gerätegruppen oder Geräte.
Testoptionen der integrierten Systemdiagnose Klicken Sie auf die Testoption im Fenster Main Menu (Hauptmenü). Testoption Funktion Express Test Führt eine schnelle Überprüfung des Systems durch. Bei dieser Option werden Gerätetests durchgeführt, bei denen keine Eingabe durch den Benutzer erforderlich ist. Extended Test Führt eine genauere Überprüfung des Systems durch. Dieser Test kann eine Stunde oder länger dauern. Custom Test Testet ein bestimmtes Gerät. Information Zeigt Testergebnisse an.
Auswählen von Diagnoseoptionen Die Testoptionen für ein Gerät können Sie im Bereich Diagnostics Options einstellen. • Non-Interactive Tests Only – Führt nur Tests durch, die keine Benutzereingaben erfordern. • Quick Tests Only – Führt nur die schnell durchführbaren Tests am Gerät durch. • Show Ending Timestamp – Schreibt die Zeiten der Tests in die Protokolldatei. • Test Iterations – Legt fest, wie oft der Test durchgeführt wird.
Wie Sie Hilfe bekommen Kontaktaufnahme mit Dell Kunden in den USA können die Nummer 800-WWW-DELL (800-999-3355) anrufen. ANMERKUNG: Wenn Sie nicht mit dem Internet verbunden sind, finden Sie die Kontaktinformationen auf der Rechnung, dem Lieferschein oder im Produktkatalog von Dell. Dell stellt verschiedene online- und telefonbasierte Optionen für Support und Service zur Verfügung.
Wie Sie Hilfe bekommen
Jumper, Schalter und Anschlüsse Dieser Abschnitt enthält spezifische Informationen über die Jumper (Steckbrücken) des Systems. Darüber hinaus erhalten Sie einige grundlegende Informationen zu Jumpern und Schaltern, und die Anschlüsse auf den verschiedenen Platinen im System werden beschrieben. Jumper auf der Systemplatine Abbildung 7-1 zeigt die Position der Konfigurations-Jumper auf der Systemplatine. Tabelle 7-1 können Sie die Jumpereinstellungen entnehmen. Tabelle 7-1.
Anschlüsse auf der Systemplatine Abbildung 7-1 und Tabelle 7-2 können Sie die Positionen und Beschreibungen der Systemplatinenanschlüsse entnehmen. Abbildung 7-1.
Tabelle 7-2.
Tabelle 7-2.
3 Setzen Sie den Kennwort-Jumper auf die Position „deaktiviert“, um das Kennwort zu löschen. Siehe Tabelle 7-1. Abbildung 7-1 zeigt die Position des Kennwort-Jumpers auf der Systemplatine. 4 Schließen Sie das System. 5 Verbinden Sie das System und die Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein. Die vorhandenen Kennwörter werden erst dann deaktiviert (gelöscht), wenn das System mit dem Kennwort-Jumper in der Position „deaktiviert“ neu gestartet wird.
Jumper, Schalter und Anschlüsse
Glossar A: Ampère. AC: Alternating Current (Wechselstrom). ACPI: Advanced Configuration and Power Interface. Eine Standardschnittstelle, die dem Betriebssystem eine direkte Konfiguration und Energieverwaltung ermöglicht. ANSI: American National Standards Institute. Die wichtigste Organisation für die Entwicklung technologischer Standards in den USA. Asset Tag (Systemkennnummer): Ein eindeutiger Code, der dem System üblicherweise vom Systemadministrator zu Sicherheits- und Verwaltungszwecken zugewiesen wird.
Controller: Ein Chip oder eine Erweiterungskarte, die die Übertragung von Daten zwischen Prozessor und Speicher bzw. zwischen Prozessor und einem Peripheriegerät steuert. Coprozessor: Ein Chip, der den Hauptprozessor des Systems bei bestimmten Arbeitsaufgaben entlastet. Ein mathematischer Coprozessor ist beispielsweise für numerische Aufgaben zuständig. CPU: Central Processing Unit (Zentrale Recheneinheit). Siehe Prozessor.
Erweiterungsbus: Das System besitzt einen Erweiterungsbus, über den der Prozessor direkt mit den Controllern der Peripheriegeräte (wie z. B. NICs) Daten austauschen kann. Erweiterungskarte: Eine Steckkarte wie z. B. eine Netzwerk- oder eine SCSI-Karte, die in einen Erweiterungssteckplatz auf der Systemplatine eingebaut wird.
Grafikmodus: Darstellungsmodus, der durch x horizontale Bildpunkte mal y vertikale Bildpunkte mal z Farben definiert wird. Grafikspeicher: Die meisten VGA- und SVGA-Grafikkarten besitzen eigene Speicherchips zusätzlich zum RAM-Speicher des Systems. Die Größe des installierten Videospeichers beeinflusst die Anzahl der Farben, die ein Programm anzeigen kann (mit den entsprechenden Videotreibern und den Fähigkeiten des Monitors).
kHz: Kilohertz. KVM: Keyboard/Video/Mouse (Tastatur/Bildschirm/Maus). Mit einem KVM-Switch lassen sich mehrere Systeme mit nur einem Bildschirm, einer Tastatur und einer Maus betreiben. LAN: Local Area Network (lokales Netzwerk). Ein LAN ist normalerweise auf das gleiche oder einige benachbarte Gebäude beschränkt, wobei alle Geräte in einem Netzwerk durch Verkabelung fest miteinander verbunden sind. LCD: Liquid Crystal Display (Flüssigkristallanzeige). LED: Light-Emitting Diode (Leuchtdiode).
NIC: Network Interface Controller (Netzwerkcontroller). Integrierter Netzwerkcontroller oder Erweiterungskarte, über die eine Verbindung zu einem Netzwerk (z. B. LAN) hergestellt werden kann. NMI: Nonmaskable Interrupt. Ein NMI wird bei Hardwarefehlern von einem Gerät an den Prozessor gesendet. ns: Nanosekunde. NVRAM: Nonvolatile Random Access Memory (Nicht flüchtiger Speicher mit wahlfreiem Zugriff). Speicher, dessen Inhalt beim Abschalten des Systems nicht verloren geht.
RAC: Remote Access Controller (Fernzugriffscontroller). RAID: Redundant Array of Independent Disks. Eine Datenredundanztechnik. Zu den gebräuchlichen RAID-Implementierungen zählen RAID 0, RAID 1, RAID 5, RAID 10 und RAID 50. Siehe auch Datenspiegelung und Striping. RAM: Random Access Memory (Speicher mit wahlfreiem Zugriff). Der primäre und temporäre Speicher des Systems für Programminstruktionen und Daten. Beim Ausschalten des Systems gehen alle im RAM abgelegten Daten und Befehle verloren.
SMART: Self-Monitoring Analysis and Reporting Technology. Technologie, mit der Festplattenlaufwerke Fehler und Ausfälle an das System-BIOS melden können, das dann eine entsprechende Fehlermeldung auf dem Bildschirm anzeigt. SMP: Symmetrisches Multiprocessing. SMP ist ein Verfahren, bei dem mindestens zwei Prozessoren mit hoher Datenrate miteinander verbunden sind und von einem Betriebssystem gesteuert werden. Dabei hat jeder Prozessor gleichen Zugriff auf E/AGeräte. SNMP: Simple Network Management Protocol.
System-Setup-Programm: Ein BIOS-basiertes Programm, mit dem die Hardware des Systems konfiguriert und der Systembetrieb an die eigenen Bedürfnisse angepasst werden kann. Zum Beispiel können Einstellungen zur Energieverwaltung und Kennwörter festgelegt werden. Da das System-Setup-Programm im NVRAM gespeichert ist, bleiben alle Einstellungen unverändert, bis sie erneut geändert werden. Systemspeicher: Siehe RAM. Systemsteuerung: Der Teil des Systems, der die Anzeigen und Bedienelemente enthält, z. B.
VGA: Video Graphics Array. VGA und SVGA sind Standards für Grafikkarten, die sich im Vergleich zu früheren Standards durch höhere Auflösungen und größere Farbtiefe auszeichnen. Virtualisierung: Die Fähigkeit, mit Software die Ressourcen eines einzelnen Computer in mehreren Umgebungen zu nutzen. Ein einzelnes physisches System kann dem Benutzer wie mehrere virtuelle Systeme erscheinen, auf denen verschiedene Betriebssysteme aktiv sind. W: Watt. Wh: Wattstunde. XML: Extensible Markup Language.
Stichwortverzeichnis A B Abdeckung Öffnen, 92 Schließen, 93 Bandlaufwerk Fehlerbehebung, 171 Akku Fehlerbehebung bei der RAID-Kartenbatterie, 173 Anschlüsse Bildschirm, 10 Systemplatine, 186 USB, 10 Anweisungen nur für Service Systemplatine, 154 Anzeigen NIC, 20 Rückseite, 18 Stromversorgung, 10, 21 Vorderseite, 10 Arbeitsspeicher Fehlerbehebung, 167 Austauschen Kühlungslüfter, 124 Netzteil, 103, 106 Systembatterie, 142 Batterie (System) Austauschen, 142 Batterien Fehlerbehebung, 165 Bedienfeldbaugrupp
D Dell Kontaktaufnahme, 183 Dell Online Diagnostics Verwenden, 179 Diagnose Einsatzbereiche, 180 Erweiterte Testoptionen, 181 Testoptionen, 181 Verwenden der integrierten Systemdiagnose, 179 Verwenden von Online Diagnostics, 179 DIMMs Siehe Speichermodule (DIMMs) E Einsetzen Kühlgehäuse, 117 Entfernen Abdeckung, 92 Bedienfeldbaugruppe, 144 Erweiterungskarte, 109 Festplatten (hot-plug-fähig), 95 Festplattenlaufwerk (verkabelt), 98 Frontverkleidung, 91 Kühlgehäuse, 115 Laufwerksplatzhalter, 94 Netzteil, 102,
Fehlerbehebung (fortgesetzt) SD-Karte, 169 Systemkühlung, 166 Tastatur, 160 Fehlermeldungen, 65 Festplatte Fehlerbehebung, 172 Festplatten (hot-plug-fähig) Entfernen, 95 Installieren, 96 Festplattenlaufwerke (verkabelt) Entfernen, 98 Installieren, 100 Feuchtigkeit im System Fehlerbehebung, 163 Frontverkleidung, 91 G Grafik Fehlerbehebung, 160 Installieren Bedienfeldbaugruppe, 148 Erweiterungskarte, 107 Festplatte (hot-plug-fähig), 96 Festplattenlaufwerk (verkabelt), 100 iDRAC-Karte, 117, 119 Laufwerksplat
Kühlkörper, 138 N Kühlungslüfter Austauschen, 124 Fehlerbehebung, 167 Netzteile Anzeigen, 21 Austauschen, 103, 106 Entfernen, 102, 104 Netzteilplatzhalter, 104 L Laufwerksplatzhalter Entfernen, 94 Installieren, 95 LCD-Display Menüs, 15 Merkmale, 13 NIC Anschlüsse auf der Rückseite, 18 Anzeigen, 20 NICs Fehlerbehebung, 162 O M Meldungen Fehlermeldungen, 65 Status-LCD, 24 System, 42 Warnung, 61 Merkmale des vorderen Bedienfelds, 10 Mikroprozessor Siehe Prozessor.
R Remote-Access-Controller Siehe iDRAC Richtlinien Anschließen von externen Geräten, 20 Installation von Erweiterungskarten, 106 Speicherinstallation, 129 Rückseitige Funktionsmerkmale, 18 Rufnummern, 183 S SAS-Controllerkarte Entfernen, 110 Installieren, 111 SAS-Controllerzusatzkarte Fehlerbehebung, 173 SAS-Festplattenlaufwerk. Siehe Festplatte. SAS-RAID-Controllerzusatzkarte Fehlerbehebung, 173 SAS-Rückwandplatine Entfernen, 148 Installieren, 151 SATA-Festplattenlaufwerk. Siehe Festplatte.
Systemkühlung Fehlerbehebung, 166 Systemmeldungen, 42 Systemplatine Anschlüsse, 186 Entfernen, 154 Installieren, 156 Jumper, 185 U UEFI Boot Manager aufrufen, 79 Hauptbildschirm, 80 System Utilities (Bildschirm), 81 UEFI Boot Settings (Bildschirm), 80 Unified Server Configurator, 86 System-Setup-Bildschirme Hauptbildschirm, 66 Upgrades Prozessor, 137 System-Setup-Programm Energieverwaltungsoptionen, 75 Integrierte Serververwaltungsoptionen, 74 Optionen für die Systemsicherheit, 76 Optionen für integrier