Dell PowerEdge R415 システム ハードウェアオーナ ーズマニュアル 認可モデル E07S シリーズ 認可タイプ E07S003
メモ、注意、警告 メモ:コンピュータを使いやすくするための重要な情報を説明して います。 注意:手順に従わないと、ハードウェアの損傷やデータの損失につなが る可能性があることを示しています。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示 しています。 ____________________ 本書の内容は予告なく変更されることがあります。 © 2010 すべての著作権は Dell Inc. にあります。 Dell Inc. の書面による許可のない複製は、いかなる形態においても厳重に禁じられ ています。 本書に使用されている商標:Dell™、DELL ロゴ、および PowerEdge™ は Dell Inc. の商標 です。Microsoft®、Windows®、MS-DOS® および Windows Server® は米国その他の国に おける Microsoft Corporation の商標または登録商標です。 商標または製品の権利を主張する事業体を表すためにその他の商標および社名が使用され ていることがあります。それらの商標や会社名は、一切 Dell Inc.
目次 1 システムについて . . . . . . . . . . . . . . . . . . 起動中にシステムの機能にアクセスする方法 . 前面パネルの機能およびインジケータ . LCD パネルの機能(オプション) . . . . 9 9 . . . . . . 10 . . . . . . . . . 13 ハードドライブインジケータのパターン . . . . . 17 . . . . . . 18 . . . . . . . . 20 NIC インジケータコード . . . . . . . . . . . . . . . 20 電源インジケータコード . . . . . . . . . . . . . . . 21 背面パネルの機能およびインジケータ . 外付けデバイス接続のガイドライン 診断ライト(オプション) . . . . . . . . . . . . . . 22 LCD ステータスメッセージ . . . . . . . . . . . . . . 25 . . . . . . . . . . . . . . . . .
2 セットアップユーティリティと UEFI ブートマネージャの使い方 システム起動モードの選択 . . . . . . 61 . . . . . . . . . . . . . 61 セットアップユーティリティの起動 . . . . . . . . セットアップユーティリティのオプション UEFI ブートマネージャの起動 . . . . 63 . . . . . . . . . . . . 78 システムパスワードとセットアップ パスワードの機能 . . . . . . . . . . . 組み込みシステム管理. . . . . . . . . 81 . . . . . . . . . . . . . . . . 86 ベースボード管理コントローラの設定 iDRAC6 設定ユーティリティ 3 . . . . . . . 86 . . . . . . . . . . . . . 87 システム部品の取り付け . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 システムの内部 .
内蔵 USB メモリキー . . . . . . . . . . . . . . . . . システム基板エアフローカバー 配電基板エアフローカバー . . . . . . . . . . . . 123 . . . . . . . . . . . . . 125 iDRAC6 Express カード(オプション). . . . . . . . iDRAC6 Enterprise カード(オプション). 128 . . . . . . . . . . . 132 . . . . . . . . . . . . . . . . . . . . . . . 132 RAID バッテリー(オプション) . . . . . . . . . . . 135 . . . . . . . . . . . . . . . . . . . . 137 . . . . . . . . . . . . . . . . . . . . . . . 144 システムメモリ プロセッサ システムバッテリー . . . . . . . . . . . . . . . . . .
USB デバイスのトラブルシューティング . . . . . 171 . . . . . . . 172 . . . . . . . . . . 172 シリアル I/O デバイスのトラブルシ ューティング . . . . . . . . . . . . . . NIC のトラブルシューティング システムが濡れた場合のトラブルシ ューティング . . . . . . . . . . . . . . . . . . . . . システムが損傷した場合のトラブルシ ューティング . . . . . . . . . . . . . . . システムバッテリーのトラブルシ ューティング . . . . . . . . . . . . . . . . . . . 175 . . . . . . . . 176 電源ユニットのトラブルシューティング . . . . . システム冷却問題のトラブルシューティング . ファンのトラブルシューティング . 177 . . . . . . . . 178 . . . 179 . . . . 181 . . . . . .
5 システム診断プログラムの実行 Dell Diagnostics の使い方 . . . . . . . . . . . . . . . . . . . . 内蔵されたシステム診断プログラムの機能 内蔵されたシステム診断プログラムの実 行が必要な場合 . . . . . . . . . . . . . . . 194 . . . . . 194 . . . . システム診断プログラムのテストオプション . カスタムテストオプションの使い方 ジャンパとコネクタ 195 . . . . . . . . 196 199 システム基板のジャンパ . . . . . . . . . . . . . . . 199 システム基板のコネクタ . . . . . . . . . . . . . . . 200 . . . . . . . . 拡張カードライザーボードのコンポーネン トおよび PCIe バス . . . . . . . . . . . . . . . 配電基板コネクタ 困ったときは 202 . . . . 203 . . . . . . . . . . .
目次
システムについて 起動中にシステムの機能にアクセスする方法 起動時に以下のキー操作を行うと、システム機能にアクセスできます。 キーストローク 説明 セットアップユーティリティが起動します。61 ページの 「セットアップユーティリティと UEFI ブートマネージャの使 い方」を参照してください。 システムサービスが起動し、Lifecycle Controller が開きま す。Lifecycle Controller を使用して、システム診断プログラ ムなどの内蔵されたユーティリティにアクセスできます。詳 細については、support.dell.
前面パネルの機能およびインジケータ 図 1-1 前面パネルの機能およびインジケータ 7 8 6 1 2 3 4 5 9 10 項目 インジケータ、ボタ アイコン ン、またはコネクタ 説明 1 電源インジケータ、 電源ボタン 電源オンインジケータは、システム の電源が入っている時に点灯します。 電源ボタンによってシステムへの直 流電源の供給を制御します。オプ ションのシステムベゼルを取り付け ると、電源ボタンにアクセスできな くなります。 メモ:システムに搭載されているメ モリの容量によっては、システムに 電源を入れてからビデオモニターに 画像が表示されるまでに数秒から 2 分以上かかる場合があります。 メモ:ACPI 対応の OS では、電源ボ タンを使ってシステムの電源を切っ ても、システムの電源が切れる前に システムが正常なシャットダウンを 行うことができます。 10 システムについて
項目 インジケータ、ボタ アイコン ン、またはコネクタ 説明 2 NMI ボタン 特定の OS を使用している際に、ソフ トウェアエラーおよびデバイスドラ イバエラーのトラブルシューティン グを行うために使用します。このボ タンは、ペーパークリップの先端を 使って押すことができます。 認定を受けたサポート担当者によっ て指示された場合、または OS のマ ニュアルで指示されている場合にの み、このボタンを使用してください。 3 ビデオコネクタ モニターをシステムに接続します。 4 LCD メニューボタン コントロールパネル LCD メニューの 切り替えに使用します。 システムについて 11
項目 インジケータ、ボタ アイコン ン、またはコネクタ 説明 5 LED または LCD パ ネル メモ:お使いのシステムには、構成 に応じて LED 診断インジケータか LCD パネルが備わっています。 LED パネル:システムの起動中に、 4 つの診断インジケータがエラー コードを表示します。22 ページの 「診断ライト(オプション) 」を参照 してください。 LCD パネル:システム ID、ステータ ス情報、システムエラーメッセージ が表示されます。 LCD は通常のシステム動作中に点灯 します。特定のシステムを識別する には、システム管理ソフトウェアと システムの前面および背面にある識 別ボタンのどちらも使うことができ ます。青色の LCD の点滅で、どのシ ステムかが識別できます。 システムに注意が必要な状況になる と LCD が黄色に点灯し、LCD パネル にはエラーコードとエラーの内容を 説明するテキストが表示されます。 メモ:システムが AC 電源に接続さ れている状態でエラーが検知される と、LCD はシステムの電源がオンに なっていてもいなくても黄色に点灯 します。 6 12
項目 インジケータ、ボタ アイコン ン、またはコネクタ 説明 7 USB コネクタ(2) USB デバイスをシステムに接続する ときに使用します。ポートは USB 2.0 対応です。 8 ハードドライブ(4) 3.5 インチ HDD ホットスワップキャ リア内に 2.5 インチドライブ 4 台ま で、またはケーブル接続 / ホットス ワップの 3.
図 1-2 LCD パネルの機能 1 2 3 4 項目 ボタン 説明 1 左 カーソルが後方に 1 つ分移動します。 2 選択 カーソルによってハイライト表示されてい るメニュー項目を選択します。 3 右 カーソルが前方に 1 つ分移動します。 メッセージのスクロール中に次の操作がで きます。 • 1 回押すとスクロールが速くなります。 • 再び押すと停止します。 • もう 1 回押すとデフォルトのスクロール速 度に戻ります。 • もう 1 回押すと同じ操作が繰り返さ れます。 4 システム識別 システム識別モードのオン(LCD パネルが 青色に点滅)とオフを切り替えます。 すばやく押してシステム識別のオン / オフ を切り替えます。POST 中にシステムがハン グした場合は、システム識別ボタンを 5 秒 以上押し続けて BIOS プログレスモードに入 ります。 14 システムについて
ホーム画面 ホーム画面には、ユーザーが設定可能なシステム関連情報が表示されま す。この画面は、ステータスメッセージやエラーメッセージがない通常の システム動作中に表示されます。システムがスタンバイモードの場合、エ ラーメッセージがなければ、コンピュータを操作しない時間が 5 分間続 くと LCD バックライトが消灯します。3 つのナビゲーションボタン(選 択、左、右)のいずれかを押すとホーム画面が表示されます。 が表 別のメニューからホーム画面に移動するには、ホームアイコン 示されるまで上矢印 を選択し続け、次にホームアイコンを選択します。 ホーム画面から、Select(選択)ボタンを押してメインメニューに入りま す。サブメニュー Setup(セットアップ)および View(表示)につい ては、以下の表を参照してください。 Setup(セットアップ)メニュー メモ:Setup(セットアップ)メニューでオプションを選択すると、次の 動作に進む前にオプションの確認が求められます。 オプション 説明 BMC または DRAC メモ:システムに iDRAC6 Express カードが 取り付けられている場 合、
オプション Set home (ホームの設定) 説明 LCD ホーム画面に表示するデフォルト情報を選択し ます。ホーム画面にデフォルトで表示されるように 選択できるオプションとオプション項目について は、16 ページの「View(表示)メニュー」を参照 してください。 View(表示)メニュー オプション 説明 BMC IP または DRAC IP iDRAC6 の IPv4 または IPv6 アドレスが表示されま す。アドレスには、DNS(Primary(プライマリ) ) 、Gateway iDRAC6 Express カードが および Secondary(セカンダリ) (ゲートウェイ) 、IP、および Subnet(サブネット) 取り付けられている場 。 合、BMC IP オプションは があります(IPv6 にはサブネットはありません) DRAC IP に取って代わら メモ:BMC IP は IPv4 アドレスのみをサポート します。 れます。 メモ:システムに MAC DRAC、iSCSIn、または NETn の MAC アドレスが 表示されます。 メモ:システムに iDRAC6 Exp
ハードドライブインジケータのパターン 図 1-3 ハードドライブインジケータ 1 1 ハードドライブ動作インジ ケータ(緑色) 2 2 ハードドライブ状態インジケータ コード (緑色と黄色) システムについて 17
ドライブステータスインジケータのパ 状態 ターン(RAID のみ) 1 秒間に 2 回緑色に点滅 ドライブの識別 / 取り外し準備中 消灯 ドライブの挿入または取り外し可 メモ:システム電源の投入後、すべて のハードドライブの初期化が完了する まで、ドライブステータスインジケー タは消灯しています。この間、ドライ ブの挿入も取り外しもできません。 緑色、黄色に点滅し、消灯 ドライブ障害の予測 1 秒間に 4 回黄色に点滅 ドライブに障害発生 緑色にゆっくり点滅 ドライブのリビルド中 緑色の点灯 ドライブオンライン状態 緑色に 3 秒間点滅、黄色に 3 秒間点 滅、6 秒間消灯 リビルドが中断 背面パネルの機能およびインジケータ 図 1-4 背面パネルの機能およびインジケータ 1 2 3 4 5 項目 インジケータ、ボタ ン、またはコネクタ 6 7 アイコン 8 9 10 11 12 説明 1 シリアルコネクタ シリアルデバイスをシステムに接続 します。 2 ビデオコネクタ VGA ディスプレイをシステムに接続 します。 18 システムにつ
項目 インジケータ、ボタ ン、またはコネクタ アイコン 説明 3 VFlash メディアスロッ ト(オプション) オプションの iDRAC6 Enterprise カード用の外付け SD メモリカード を取り付けます。 4 iDRAC6 Enterprise ポート(オプション) オプションの iDRAC6 Enterprise カード専用の管理ポート。 5 USB コネクタ(2) USB デバイスをシステムに接続する ときに使用します。ポートは USB 2.
外付けデバイス接続のガイドライン • 新しい外付けデバイスを取り付ける前に、システムと外付けデバイ スの電源を切ります。デバイスのマニュアルに特別な指示がない限 り、システムの電源を入れる前に外付けデバイスの電源を入れます。 • 取り付けたデバイスの適切なドライバがシステムにインストールさ れていることを確認します。 • システムのポートを有効にするのに必要な場合は、セットアップ ユーティリティを使用します。61 ページの「セットアップユーティ リティと UEFI ブートマネージャの使い方」を参照してください。 NIC インジケータコード 図 1-5 NIC インジケータ 1 1 2 リンクインジケータ 2 アクティビティインジケータ インジケータ インジケータコード リンクおよびアクティ ビティインジケータが 消灯 NIC がネットワークに接続されていません。 リンクインジケータが 緑色 NIC が 1000 Mbps で有効なリンクに接続されていま す。 リンクインジケータが 黄色 NIC が 10/100 Mbps で有効なネットワークリンクに 接続されています。
電源インジケータコード 電源ユニットには、電力が供給されているか、または電源の障害が発生し ているかを示すインジケータがあります。 • 消灯 — AC 電源が接続されていません。 • 緑色 — スタンバイモードでは、緑色のライトは、有効な AC 電源が 電源ユニットに接続され、電源ユニットが稼動していることを示し ます。システムの電源が入っているとき、緑色のライトは、電源ユ ニットがシステムに DC 電力を供給していることも示します。 • 黄色 — 電源ユニットに問題があることを示します。 • 緑色と黄色が交互に点灯 — 電源ユニットのホットアッド時にこのシ グナルが出た場合、電源ユニットがもう一台の電源ユニットと適合 していないことを示します(たとえば、高出力の電源ユニットと Energy Smart [ 省電力構成 ] の電源ユニットが同じシステムに取り 付けられている)。インジケータが点滅している電源ユニットを、取 り付けられているもう一台の電源ユニットとワット数が一致するも のに交換してください。 注意:電源ユニットのミスマッチを解決する場合は、インジケータが点 滅している電源ユニットの
図 1-6 電源ユニットステータスインジケータ 1 1 電源ユニットステータスインジ ケータ 診断ライト(オプション) システムの起動中に、システム前面パネルの 4 つの診断インジケータが エラーコードを表示します。表 1-1 に、エラーコードに関連する原因と可 能な対応策を一覧表示します。ハイライトされている場合は点灯、ハイラ イトされていない場合は消灯を表します。 メモ:LCD ディスプレイのあるシステムには、Diag LED はありません。 22 システムについて
表 1-1 診断インジケータコード(オプション) コード 原因 対応処置 システムが通常のオフ 正常なコンセントにシステ の状態、または BIOS に ムを接続し、電源ボタンを押し 障害が発生している可 ます。 能性があります。 システムが OS から正 常に起動した後は、こ の診断ライトは点灯し ません。 POST 後、システムが正 情報表示のみです。 常に動作しています。 BIOS チェックサム障害 207 ページの「困ったときは」 が検知されました。シ を参照してください。 ステムは復元モード です。 プロセッサに障害が発 生している可能性があ ります。 190 ページの「プロセッサのト ラブルシューティング」を参照 してください。 メモリ障害。 179 ページの「システムメモリ のトラブルシューティング」を 参照してください。 拡張カードに障害が発 生している可能性があ ります。 189 ページの「拡張カードのト ラブルシューティング」を参照 してください。 ビデオに障害が発生し ている可能性があり ます。 207 ページの「困ったときは」 を参照してください。 ハードドライブに
表 1-1 診断インジケータコード(オプション)(続き) コード 原因 対応処置 USB に障害が発生して 171 ページの「USB デバイスの いる可能性があります。 トラブルシューティング」を参 照してください。 メモリモジュールが検 知されません。 179 ページの「システムメモリ のトラブルシューティング」を 参照してください。 システム基板の障害。 207 ページの「困ったときは」 を参照してください。 メモリの構成エラー。 179 ページの「システムメモリ のトラブルシューティング」を 参照してください。 システム基板リソース 207 ページの「困ったときは」 およびシステム基板 を参照してください。 ハードウェアのどちら かまたは両方に障害が ある可能性があります。 24 システムリソース設定 エラーの可能性があり ます。 207 ページの「困ったときは」 を参照してください。 その他の障害。 ディスケットドライブ、オプ ティカルドライブ、およびハー ドドライブが正しく取り付けら れていることを確認します。シ ステムに取り付けられているド ライブの種類に応じて、 16
LCD ステータスメッセージ LCD メッセージは、システムイベントログ(SEL)に記録されたイベント に言及する短いテキストメッセージで構成されています。SEL およびシス テム管理設定の詳細については、support.dell.
表 1-2 LCD ステータスメッセージ(オプション) コード メッセージ 原因 E1000 Failsafe 重大なエラーイベントが システムの AC 電源を voltage error. ないか、システムイベン 10 秒間切断し、システ Contact トログを確認します。 ムを再び起動します。 support. 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E1114 Ambient Temp 周囲温度が許容範囲を外 177 ページの「システ exceeds れた。 ム冷却問題のトラブル allowed range. シューティング」を参 照してください。 E1116 Memory disabled, temp above range. Power cycle AC.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1211 RAID Controller battery failure. Check battery. RAID バッテリーがない か、不良であるか、また は温度が正常でないため に再充電できない。 RAID バッテリーコネク タを抜き差しします。 135 ページの「RAID バッテリー(オプショ ン) 」および 177 ページ の「システム冷却問題 のトラブルシューティ ング」を参照してくだ さい。 E122E On-board regulator failed. Call support. オンボード電圧レギュ レータの 1 つに障害が 発生した。 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 E1243 CPU # VCORE Regulator failure. Contact Support.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ E1313 Fan redundancy システムのファン冗長性 LCD をスクロールして lost. Check が失われた。もう 1 つ その他のメッセージを fans. のファンに障害が発生す 確認します。178 ペー ると、システムはオー ジの「ファンのトラブ バーヒートするおそれが ルシューティング」を ある。 参照してください。 E1314 Critical すべてのファンがシ system cooling ステムから取り外されて loss. Check いる。 fans. E1410 System Fatal Error detected. 致命的なシステムエラー LCD をスクロールして が検知された。 その他のメッセージを 確認します。システム の AC 電源を 10 秒間切 断し、システムを再び 起動します。問題が解 決しない場合は、 207 ページの「困った ときは」を参照してく ださい。 E1414 CPU # temp exceeding range.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1418 CPU # not detected. Check CPU is seated properly. 表示されているプロセッ サがないか不良であるた め、システムはサポート されていない構成になっ ている。 表示されているマイク ロプロセッサが正しく 取り付けられているこ とを確認します。 190 ページの「プロ セッサのトラブル シューティング」を参 照してください。 E141C Unsupported プロセッサがサポートさ お使いのシステムの CPU れていない構成になって『はじめに』のプロセッ configuration. いる。 サ仕様で説明されてい Check CPU or るタイプに一致するプ BIOS revision. ロセッサが使用されて いることを確認します。 E141F CPU # protocol システム BIOS によって システムの AC 電源を error. Power プロセッサプロトコルエ 10 秒間切断し、システ cycle AC.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1422 CPU # machine check error. Power cycle AC. システム BIOS によって システムの AC 電源を マシンチェックエラーが 10 秒間切断し、システ 報告された。 ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E1610 Power Supply # 表示されている電源ユ 177 ページの「電源ユ (### W) ニットがシステムから取 ニットのトラブル missing. り外されているか、また シューティング」を参 Check power はシステム内にない。 照してください。 supply. E1614 Power Supply # 表示されている電源ユ (### W) error. ニットに障害が発生 Check power した。 supply.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1625 PS AC Current 電源が許容範囲外。 AC 電源を確認します。 E1626 Power Supply システム内の電源ユニッ ワット数の等しい電源 Mismatch. PSU1 トのワット数が一致して ユニットが取り付けら = ### W, PSU2 いない。 れていることを確認し = ### W. ます。お使いのシステ ムの『はじめに』に記 載されている仕様を参 照してください。 E1629 Power required > PSU wattage. Check PSU and config. E1632 FailSafe 現在の電源ユニット構成 システムの AC 電源を event. Contact でシステムの消費電力を 10 秒間切断し、システ support.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 E1711 PCI parity error on Bus ## Device ## Function ## システム BIOS によっ PCIe 拡張カードを取り て、バス ##、デバイス 外して装着しなおしま ##、機能 ## の PCI 設定 す。問題が解決しない スペースにあるコンポー 場合は、189 ページの ネントについて、PCI パ 「拡張カードのトラブル リティエラーが報告 シューティング」を参 された。 照してください。 PCI parity error on Slot #. Review & clear SEL.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1714 Unknown error. システム BIOS によって Review & clear システムにエラーが検知 SEL. されたが、原因を特定す ることはできなかった。 詳細をチェックしてか ら SEL をクリアします。 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E1715 Fatal I/O Error. Review & clear SEL. システム BIOS がシステ 詳細をチェックしてか ム内に致命的なエラーが ら SEL をクリアします。 あると判断した。 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E1716 Chipset IERR Bus ## Dev ## Function ##. Review & clear SEL.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 E171F PCIe fatal error on Bus ## Device ## Function ## システム BIOS によっ PCIe 拡張カードを取り て、バス ##、デバイス 外して装着しなおしま ##、機能 ## の PCI 設定 す。問題が解決しない スペースにあるコンポー 場合は、189 ページの ネントについて、PCIe 「拡張カードのトラブル の致命的なエラーが報告 シューティング」を参 された。 照してください。 PCIe fatal error on Slot #. Review & clear SEL.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1A11 PCI Riser hardware & configuration mismatch. Reconfigure. PCIe ライザーが正しく 設定されていない。無効 な設定だと、システムの 電源が入らない場 合がある。 拡張カードライザーを 取り付けなおします。 111 ページの「拡張 カードと拡張カードラ イザー」を参照してく ださい。 問題が解決しない場合 は、ライザーカードま たはシステム基板に障 害があります。 207 ページの「困った ときは」を参照してく ださい。 PCIe ライザーの片方ま たは両方がない。このた めにシステムの電源が入 らない。 E1A12 PCI Riser not detected. Check Riser. E1A14 SAS cable A SAS ケーブル A がない failure. Check か、または不良。 connection.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E1A1D Control panel USB cable not detected. Check cable. コントロールパネルに USB ケーブルが取り付 けられていないか、また はケーブルが不良。 ケーブルを抜き差しし ます。問題が解決しな い場合は、ケーブルを 交換します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E2010 Memory not システム内にメモリが検 メモリを取り付けるか、 detected. 知されなかった。 またはメモリモジュー Inspect DIMMs. ルを抜き差しします。 141 ページの「メモリ モジュールの取り付け」 または 179 ページの 「システムメモリのトラ ブルシューティング」 を参照してください。 E2011 Memory configuration failure. Check DIMMs.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 E2015 DMA Controller DMA コントローラ failure. Power の障害。 cycle AC. 対応処置 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E2016 Interrupt 割り込みコントローラの システムの AC 電源を Controller 障害。 10 秒間切断し、システ failure. Power ムを再び起動します。 cycle AC. 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E2017 Timer refresh タイマーリフレッシュの システムの AC 電源を failure. Power エラー。 10 秒間切断し、システ cycle AC.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E201A SuperIO failure.Power cycle AC. SIO 障害。 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 キーボードコントローラ システムの AC 電源を の障害。 10 秒間切断し、システ ムを再び起動します。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E201B Keyboard Controller error.Power cycle AC. E201C SMI SMI(システム管理割り システムの AC 電源を initialization 込み)の初期化障害。 10 秒間切断し、システ failure. Power ムを再び起動します。 cycle AC.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 E201E POST memory test failure. Check DIMMs. BIOS POST メモリテス トエラー。 179 ページの「システ ムメモリのトラブル シューティング」を参 照してください。 問題が解決しない場合 は、207 ページの 「困ったときは」を参照 してください。 E2020 CPU プロセッサ構成エラー。 画面で具体的なエラー configuration メッセージを確認しま failure. Check す。190 ページの「プ screen ロセッサのトラブル message. シューティング」を参 照してください。 E2021 Incorrect メモリ構成が正し memory くない。 configuration. Review User Guide. E2022 General failure during POST. Check screen message.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ E2110 Multibit Error スロット “##”のメモ on DIMM ##. リモジュールにマルチ eseat DIMM. ビットのエラー(MBE) が発生した。 E2111 SBE log disabled on DIMM ##. Reseat DIMM. システム BIOS がメモリ SBE(シングルビットエ ラー)のロギングを無効 にした。システムを再起 動するまで、以降の SBE は記録されない。"##" は BIOS によって示され るメモリモジュール を表す。 システムの AC 電源を 10 秒間切断し、システ ムを再び起動します。 Memory spared on DIMM ##. Power cycle AC.
表 1-2 LCD ステータスメッセージ(オプション)(続き) コード メッセージ 原因 対応処置 W1228 RAID Controller battery capacity < 24hr. RAID バッテリーの残容 残容量が 24 時間を超え 量が 24 時間を下回った るまで RAID バッテ という予報的警告。 リーを充電します。 W1627 Power required > PSU wattage. Check PSU and config. 搭載されている電源ユ ニットでは、システム構 成で必要とされる電力を 供給できない。 システムの電源を切り、 ハードウェア構成を縮 小するか、またはワッ ト数の高い電源ユニッ トを取り付けて、シス テムを再び起動します。 W1628 Performance degraded.Check PSU and system configuration.
システムメッセージ システムに問題がある可能性が検知されると、システムメッセージが画面 に表示されます。 メモ:表示されたシステムメッセージが表に記載されていない場合は、 メッセージが表示されたときに実行していたアプリケーションのマニュア ルや、OS のマニュアルを参照して、メッセージの説明と推奨されている 処置を確認してください。 表 1-3 システムメッセージ メッセージ 原因 対応処置 Alert! iDRAC6 not 正常に機能していないか、 システムが再起動するま responding. または初期化が完了してい で待ちます。 Rebooting. ないために、iDRAC6 が BIOS 通信に応答していな い。システムが再起動 する。 Alert! iDRAC6 not responding. Power required may exceed PSU wattage.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving. メモリ構成が変化した(い ずれかのメモリモジュール に障害が発生したなど)結 果、ノードのインタリービ ングがサポートされなく なった。 システムは使用で きるが、ノードのインタ リービングは使用で きない。 メモリモジュールがノー ドのインタリービングを サポートする構成で取り 付けられていることを確 認します。考えられる原 因に関するその他の情報 については、ほかのシス テムメッセージを確認し てください。メモリ構成 の詳細については、 138 ページの「メモリモ ジュール取り付けの一般 的ガイドライン」を参照し てください。問題が解決 しない場合は、179 ページ の「システムメモリのト ラブルシューティング」 を参照してください。 Alert! Power required exceeds PSU wattage.
表 1-3 システムメッセージ (続き) メッセージ 原因 Alert! Redundant memory disabled! Memory configuration does not support redundant memory. セットアップユーティリ ティで冗長メモリが有効に 設定されているが、現在の 構成では冗長メモリはサ ポートされない。いずれか のメモリモジュールに不良 の可能性がある。 Alert! System fatal error during previous boot. エラーのためにシステムが 考えられる原因に関する 再起動した。 その他の情報については、 ほかのシステムメッセー ジを確認してください。 BIOS MANUFACTURING MODE detected. MANUFACTURING MODE will be cleared before the next boot. System reboot required for normal operation.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Caution! NVRAM_CLR jumper is installed on system board. NVRAM_CLR ジャンパがク リアの設定で取り付けられ ている。CMOS がクリアさ れた。 NVRAM_CLR ジャンパを デフォルトの位置(ピン 3 と 5)に移動します。ジャ ンパの位置については、 図 6-1 を参照してくださ い。システムを再び起動 し、BIOS 設定を再入力し ます。61 ページの「セッ トアップユーティリティ と UEFI ブートマネージャ の使い方」を参照してく ださい。 CPU set to minimum frequency. 節電のためにプロセッサの 処理速度が意図的に低く設 定されている可能性が ある。 意図的な設定でなければ、 考えられる原因がないか、 その他のシステムメッ セージをチェックします。 CPUs with different cache sizes detected.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Current boot mode is set to UEFI. Please ensure compatible bootable media is available. Use the system setup program to change the boot mode as needed. UEFI 起動モードが BIOS で 有効に設定されており、起 動 OS が非 UEFI であるた め、システムが起動しな かった。 起動モードが正しく設定 されており、正しいブー タブルメディアが使用可 能であることを確認しま す。61 ページの「セット アップユーティリティと UEFI ブートマネージャの 使い方」を参照してくだ さい。 Decreasing available memory.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 General failure. OS がコマンドを実行でき ない。 このメッセージの後には 通常、問題を特定する情 報が表示されます。情報 を参照し、適切な処置を とって問題を解決します。 Invalid configuration information please run SETUP program. システム構成が無効なた セットアップユーティリ め、システムが停止した。 ティを実行し、現在の設 定を確認します。61 ペー ジの「セットアップユー ティリティと UEFI ブート マネージャの使い方」を 参照してください。 Invalid PCIe card found in the Internal_Storage slot! 無効な PCIe 拡張カードが 専用のストレージコント ローラスロットに取り付け られているために、システ ムが停止した。 Keyboard controller failure.
表 1-3 システムメッセージ (続き) メッセージ 原因 Local keyboard システム BIOS で USB ポー may not work トが無効に設定され because all user ている。 accessible USB ports are disabled. If operating locally, power cycle the system and enter system setup program to change settings. 対応処置 電源ボタンを使用してシ ステムの電源を切り、再 び起動します。次にセッ トアップユーティリティ を起動して USB ポートを 有効にします。62 ページ の「セットアップユー ティリティの起動」を参 照してください。 Manufacturing mode detected. システムが製造モードに なっている。 Memory tests terminated by keystroke.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 No boot device available. オプティカルドライブサブ 起動可能な USB キー、 システム、ハードドライ CD、またはハードドライ ブ、またはハードドライブ ブを使用します。問題が サブシステムに障害がある 解決しない場合は、 か、または取り付けられて 181 ページの「内蔵 USB いない。または、起動用以 キーのトラブルシュー 外の USB キーが取り付け ティング」、171 ページの られている。 「USB デバイスのトラブル シューティング」、 183 ページの「オプティカ ルドライブのトラブル シ ューティング」、および 186 ページの「ハードドラ イブのトラブルシュー ティング」を参照してく ださい。起動デバイスの 順序を設定するための情 報については、61 ページ の「セットアップユー ティリティと UEFI ブート マネージャの使い方」を 参照してください。 No boot sector on セットアップユーティリ hard drive.
表 1-3 システムメッセージ (続き) メッセージ 原因 PCI BIOS failed to install. シャドウイング中に PCIe デバイス BIOS(オプショ ン ROM)チェックサムエ ラーが検知された。 対応処置 拡張カードを抜き差しし ます。適切なケーブルが すべてしっかりと拡張 カードに接続されている 拡張カードのケーブルに緩 ことを確認します。問題 みがある。拡張カードに障 が解決しない場合は、 害があるか、または正しく 189 ページの「拡張カード のトラブルシューティン 取り付けられていない。 グ」を参照してください。 PCIe Training 表示されているスロットの 該当するスロット番号の Error: Expected PCIe カードに障害がある、 PCIe カードを抜き差しし Link Width is x, または取り付けが不良。 ます。189 ページの「拡張 Actual Link Width カードのトラブルシュー is y.
表 1-3 システムメッセージ (続き) メッセージ 原因 Read fault. OS がハードドライブ、オ プティカルドライブ、また は USB デバイスからデー タを読み取れない。ディス ク上の特定のセクターが見 つからなかったか、要求さ れたセクターが不良。 Requested sector not found. 対応処置 オプティカルメディア、 USB メディア、またはデ バイスを交換します。SAS バックプレーン、USB、ま たは SATA ケーブルが正し く接続されていることを 確認します。システムに 取り付けられているドラ イブの種類に応じて、 171 ページの「USB デバ イスのトラブルシュー ティング」 、183 ページの 「オプティカルドライブの トラブルシ ューティン グ」、または 186 ページの 「ハードドライブのトラブ ルシューティング」を参 照してください。 SATA Port x 表示されている SATA ポー 情報表示のみです。 device not found.
表 1-3 システムメッセージ (続き) メッセージ 原因 Requested sector not found. ハードドライブ、USB デバ USB メディアまたはデバ イス、または USB メディ イスを交換します。USB アに障害がある。 または SAS バックプレー ンケーブルが正しく接続 されていることを確認し ます。システムに取り付 けられているドライブの 種類に応じて、171 ページ の「USB デバイスのトラ ブルシューティング」ま たは 186 ページの「ハー ドドライブのトラブル シューティング」を参照 してください。 Seek error. Seek operation failed. Shutdown failure. 対応処置 一般的なシステムエラー。 207 ページの「困ったとき は」を参照してください。 The amount of メモリが追加されたか、取 メモリの追加か取り外し system memory has り外されたか、またはメモ が行われた場合、この changed.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Time-of-day not set - please run SETUP program. 時刻または日付が正しく設 Time(時刻)と Date 定されていない。システム (日付)の設定を確認しま バッテリーに障害がある。 す。 61 ページの「セッ トアップユーティリティ と UEFI ブートマネー ジャの使い方」を参照し てください。問題が解決 しない場合は、システム バッテリーを交換します。 151 ページの「システム バッテリー」を参照して ください。 Timer chip システム基板に障害があ counter 2 failed. る。 207 ページの「困ったとき は」を参照してください。 TPM or TCM configuration operation honored. System will now reset.
表 1-3 システムメッセージ (続き) メッセージ 原因 Unable to launch System Services image. System halted! System Services イメージ がシステムファームウェア 内で壊れているか、または システム基板の交換によっ て失われたことが原因で、 キーを押した後にシ ステムが停止した。 対応処置 Lifecycle Controller Dell Update Package(DUP) を実行することで、シス テムを再起動し、Lifecycle Controller をアップデート します。詳細については、 support.dell.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Unsupported DIMM detected. The following DIMM has been disabled: x メモリの構成が無効。シス テムは使用できるが、表示 されているメモリモジュー ルが無効。 メモリモジュールが有効 な構成で取り付けられて いることを確認します。 138 ページの「メモリモ ジュール取り付けの一般 的ガイドライン」を参照 してください。 Unsupported memory configuration. DIMM mismatch across slots detected: x,x,...
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Warning! Power required exceeds PSU wattage. Check PSU and system configuration. プロセッサ、メモリモ ジュール、および拡張カー ドのシステム構成が電源ユ ニットによってサポートさ れていない可能性がある。 いずれかのシステムコン ポーネントをアップグ レードした直後にこの メッセージが表示された 場合は、システムを元の 構成に戻します。この メッセージが表示されず にシステムが起動する場 合は、交換したコンポー ネントがこの電源ユニッ トでサポートされていま せん。低いワット数の電 源ユニットを使用してい る場合、交換後のコン ポーネントを使用するに は高出力の電源ユニット に交換します。106 ページ の「電源ユニット」を参 照してください。 Warning! Performance degraded. CPU and memory set to minimum frequencies to meet PSU wattage.
表 1-3 システムメッセージ (続き) メッセージ 原因 Write fault. USB デバイス、USB メディ USB メディアまたはデバ ア、オプティカルドライブ イスを交換します。USB、 アセンブリ、ハードドライ SAS バックプレーン、また ブ、またはハードドライブ は SATA ケーブルが正しく サブシステムに障害が 接続されていることを確 ある。 認します。171 ページの 「USB デバイスのトラブル シューティング」、 181 ページの「内蔵 USB キーのトラブルシュー ティング」、および 186 ページの「ハードドラ イブのトラブルシュー ティング」を参照してく ださい。 Write fault on selected drive. 対応処置 Incorrect memory configuration CPU n.
表 1-3 システムメッセージ (続き) メッセージ 原因 対応処置 Warning: Following faulty DIMMs are ignored: メモリモジュールに障害が あるか、または装着されて いない。障害が発生してい ないか、同じチャネルの両 方の DIMM をチェックし ます。 179 ページの「システムメ モリのトラブルシュー ティング」を参照してく ださい。 メモリモジュールに障害が あるか、または装着されて いない。障害が発生してい ないか、同じチャネルの両 方の DIMM をチェックし ます。 179 ページの「システムメ モリのトラブルシュー ティング」を参照してく ださい。 DIMM n1 n2 Total memory size is reduced. Warning: Following faulty DIMMs are disabled: DIMM n1 n2 Total memory size is reduced.
警告メッセージ 警告メッセージは、問題発生の可能性があることを知らせ、作業を続行す る前に対応策をとるように求めます。たとえば、ディスケットをフォー マットする前に、ディスケット上のすべてのデータが失われるおそれがあ ることを警告するメッセージが表示されることがあります。警告メッセー ジは、通常、処理を中断して、y(はい)または n(いいえ)を入力して 応答することを要求します。 メモ:警告メッセージは、アプリケーションプログラムまたは OS によっ て生成されます。詳細については、OS またはアプリケーションプログラ ムに付属のマニュアルを参照してください。 診断メッセージ お使いのシステムで診断テストを実行すると、システム診断ユーティリ ティがメッセージを表示することがあります。システム診断プログラムの 詳細については、195 ページの「内蔵されたシステム診断プログラムの実 行」を参照してください。 アラートメッセージ システム管理ソフトウェアは、システムのアラートメッセージを生成しま す。アラートメッセージには、ドライブ、温度、ファン、および電源の状 態についての情報、ステータス、警告、およびエラー
その他の情報 警告:システムに付属のマニュアルで安全および認可機関に関する情報 を参照してください。保証情報は、このマニュアルに含まれている場 合と、別の文書として付属する場合があります。 • ラックソリューションに付属のマニュアルでは、システムをラック に取り付ける方法について説明しています。 • 『はじめに』では、システムの機能、システムのセットアップ、およ び仕様の概要を説明しています。 • システムに付属のメディアには、OS、システム管理ソフトウェア、 システムアップデート、およびシステムと同時に購入したシステム コンポーネントに関するものを含め、システムの設定と管理用のマ ニュアルとツールが収録されています。 メモ:アップデートには他の文書の内容を差し替える情報が含まれてい る場合がよくありますので、support.dell.
セットアップユーティリティと UEFI ブートマネージャの使い方 セットアップユーティリティとは、システムハードウェアの管理と BIOS レベルオプションの指定を行うことができる BIOS プログラムです。セッ トアップユーティリティから実行できる操作は次のとおりです。 • ハードウェアの追加または削除後に NVRAM 設定を変更する。 • システムハードウェアの構成を表示する。 • 内蔵デバイスの有効 / 無効を切り替える。 • パフォーマンスと電力管理のしきい値を設定する。 • システムセキュリティを管理する。 システム起動モードの選択 セットアップユーティリティでは、OS インストール用の起動モードを指 定することもできます。 • BIOS 起動モード(デフォルト)は、標準的な BIOS レベルの起動イ ンタフェースです。 • UEFI 起動モードは、システム BIOS にオーバーレイする UEFI (Unified Extensible Firmware Interface)仕様に基づく拡張 64 ビッ ト起動インタフェースです。このインタフェースの詳細については、 78 ペ
セットアップユーティリティの起動 1 システムの電源を入れるか、再起動します。 2 次のメッセージが表示されたら、すぐに を押します。 = System Setup(セットアップユーティリティ) を押す前に OS のロードが開始された場合は、システムの起動 が完了するのを待ってから、もう一度システムを再起動し、この手 順を実行してください。 エラーメッセージへの対応 システムの起動中にエラーメッセージが表示された場合は、メッセージを メモしてください。メッセージの説明とエラーの修正方法については、 42 ページの「システムメッセージ」を参照してください。 メモ:メモリのアップグレード後、最初にシステムを起動する際にメッ セージが表示されるのは正常です。 セットアップユーティリティナビゲーションキーの使い方 キー 動作 上矢印または 前のフィールドに移動します。 下矢印または 次のフィールドへ移動します。 スペースキー、<+>、<–>、お フィールド内の設定値を順に切り替えます。 よび左右矢印 多くのフィールドでは、適切な値を入
セットアップユーティリティのオプション メイン画面 図 2-1 メイン画面 メモ:セットアップユーティリティのオプションはシステム構成に応じ て変わります。 メモ:セットアップユーティリティのデフォルト設定を以下の項の該当 する各オプションの下に示します。 セットアップユーティリティと UEFI ブートマネージャの使い方 63
オプション 説明 System Time システム内蔵時計の時刻を設定します。 (システム時刻) System Date システム内蔵カレンダーの日付を設定します。 (システム日付) Memory Settings 取り付けられているメモリに関連する情報が表示されます。 (メモリ設定) 66 ページの「Memory Settings(メモリ設定)画面」を参 照してください。 Processor Settings(プロ セッサ設定) プロセッサに関する情報が表示されます(速度、キャッ シュサイズなど)。66 ページの「Processor Settings(プロ セッサ設定)画面」を参照してください。 SATA Settings (SATA 設定) 内蔵 SATA コントローラとポートの有効 / 無効を切り替える 画面が表示されます。68 ページの「SATA Settings(SATA 設定)画面」を参照してください。 Boot Settings (起動設定) 起動モード(BIOS または UEFI)を指定する画面が表示さ れます。BIOS 起動モードでは、起動デバイスの指定も可能 です。69 ペー
オプション 説明 Embedded Server Management (組み込みサー バー管理) 前面パネル LCD のオプションの設定、およびユーザーが指 定する LCD ストリングの設定を行う画面が表示されます。 73 ページの「Embedded Server Management(組み込み サーバー管理)画面」を参照してください。 Power Management (電力の管理) 既存の設定またはカスタム設定により、プロセッサ、ファ ン、およびメモリモジュールの電力使用を管理できます。 74 ページの「Power Management(電力の管理)画面」 を参照してください。 System Security システムパスワードおよびセットアップパスワード機能を (システムセキュ 設定する画面が表示されます。詳細については、75 ページ リティ) の「System Security(システムセキュリティ)画面」、 81 ページの「システムパスワードの使い方」および 84 ページの「セットアップパスワードの使い方」を参照し てください。 Keyboard NumLock (キーボードの Num
Memory Settings(メモリ設定)画面 オプション 説明 System Memory Size (システムメモリの サイズ) システムメモリの容量が表示されます。 System Memory Type (システムメモリの タイプ) システムメモリのタイプが表示されます。 System Memory Speed システムメモリの速度が表示されます。 (システムメモリの速度) Video Memory (ビデオメモリ) ビデオメモリの容量が表示されます。 System Memory Testing システム起動時にシステムメモリテストを実行する (システムメモリテスト) かどうかを指定します。オプションは Enabled (デフォルトは Enabled (有効)および Disabled(無効)です。 (有効)) Redundant Memory システムで冗長メモリを有効にするかどうかを指定 (冗長メモリ)(デフォル します。オプションは、Spare Mode(スペアモー トは Disabled(無効)) ド)および Disabled(無効)です。 Node Interleaving 対
オプション HyperTransport Technology (HyperTransport テクノ ロジ)(デフォルト は HT3) 説明 HyperTransport リンク速度が表示されます。この フィールドはシステムによっては読み取り専用とな ります。HT3 対応システムでは、出荷時にデフォル トで HT3 に設定されています。 HT Assist(デフォルトは HT Assist の有効 / 無効を切り替えます。 Enabled(有効) ) Virtualization Technology (仮想化テクノロジ) (デフォルトは Disabled (無効)) Enabled(有効)に設定すると、仮想化ソフトウェア がプロセッサに組み込まれている仮想化テクノロジ を使用できるようになります。 メモ:お使いのシステムで仮想化ソフトウェアを使 用しない場合は、この機能を無効にしてください。 DMA Virtualization (DMA の仮想化) DMA の再マップと仮想化用の付加的なハードウェ ア機能を有効にします。 (デフォルトは Disabled (無効)) DRAM Prefetc
オプション 説明 Number of Cores per Processor(プロセッサ のコア数)(デフォルト は All(すべて)) 各プロセッサ内の有効なコアの数を制御します。 C1E(デフォルトは Disabled(無効)) Enabled(有効)に設定すると、プロセッサはアイ ドル時に最小パフォーマンス状態に切り替わること ができます。 Processor X Family各プロセッサのシリーズとモデル番号が表示されま Model-Stepping(プロ す。サブメニューにコア速度、キャッシュメモリ容 セッサ X シリーズ - モデ 量、およびプロセッサのコアの数が表示されます。 ル - ステッピング) SATA Settings(SATA 設定)画面 オプション 説明 Embedded SATA (内蔵 SATA) (デフォルトは Off (オフ)) ATA Mode(ATA モード)に設定すると内蔵 SATA コントローラが有効になります。Off(オフ)に設定 するとコントローラが無効になります。 Port A(ポート A) (デフォルトは Off (オフ)) Auto(
オプション 説明 Port E(ポート E) Auto(自動)に設定すると、SATA ポート E に接続 されているデバイスに対する BIOS サポートが有効に なります。Off(オフ)に設定すると、デバイスに対 する BIOS サポートが無効になります。 Boot Settings(起動設定)画面 オプション Boot Mode (起動モード) (デフォルトは BIOS) 説明 注意:OS インストール時の起動モードが異な る場合、起動モードを切り替えるとシステムが 起動しなくなることがあります。 システムの OS が UEFI(Unified Extensible Firmware Interface)をサポートしている場合は、 このオプションを UEFI に設定できます。このフィー ルドを BIOS に設定すると、UEFI 非対応の OS との 互換性が有効になります。 メモ:このフィールドを UEFI に設定すると、Boot Sequence(起動順序)、Hard-Disk Drive Sequence (ハードディスクドライブの順序)、および USB Flash Drive Emulat
オプション 説明 USB Flash Drive USB フラッシュドライブのエミュレーションタイプ Emulation Type(USB を指定します。Boot Mode(起動モード)を UEFI フラッシュドライブエ に設定すると、このフィールドは無効になります。 ミュレーションタイプ) (デフォルトは Auto (自動)) Boot Sequence Retry (起動順序再試行) (デフォルトは Disabled(無効)) このフィールドが有効に設定されており、システム が起動に失敗した場合、システムは 30 秒後に起動を 再試行します。 Integrated Devices(内蔵デバイス)画面 オプション 説明 Integrated SAS Controller(内蔵 SAS コントローラ) (デフォルトは Enabled(有効)) 内蔵 SAS コントローラの有効 / 無効を切り替えます。 User Accessible USB Ports(ユーザーのアク セスが可能な USB ポート) (デフォルトは All Ports On(すべての ポートがオン) ) ユーザーがアクセス可
オプション 説明 Embedded NIC1 and NIC2(内蔵 NIC1 およ び NIC2)(デフォルト は Enabled(有効)) 内蔵 NIC の OS インタフェースの有効 / 無効を切り替 えます。NIC にはシステムの管理コントローラからも アクセスできます。 Embedded Gb NICx (内蔵 Gb NICx) (デフォルトは Enabled(有効) ) 内蔵 NIC の有効 / 無効を切り替えます。オプションは Enabled(有効)および Enabled with PXE(PXE ありで有効)です。PXE をサポートしている場合は、 ネットワークからシステムを起動できます。 MAC Address (MAC アドレス) 内蔵 10/100/1000 NIC の MAC アドレスが表示さ れます。 OS Watchdog Timer システムが反応しなくなった場合に OS のリカバリに (OS ウォッチドッグタ 役立ちます。Enabled(有効)に設定すると、OS か イマー) (デフォルトは らタイマーを初期化することができます。 Disabled(無効) )
Serial Communication(シリアル通信)画面 オプション 説明 Serial Communication (シリアル通信) (デフォルトは On without Console Redirection(コンソー ルのリダイレクトなしで オン)) BIOS 内でシリアル通信デバイス(Serial Device 1 および Serial Device 2)が有効になるかどうかを 選択します。BIOS コンソールのリダイレクトも有 効に設定できます。また、使用されるポートアドレ スを指定できます。 Serial Port Address (シリアルポートアドレ ス) (デフォルトは、Serial Device 1=COM1, Serial Device2=COM2 (シリアルデバイス 1= COM1、シリアルデバイ ス 2=COM2)) 2 つのシリアルデバイスのシリアルポートアドレス を設定します。 メモ:SOL(Serial Over LAN)には Serial Device 2 (シリアルデバイス 2)のみ使用できます。SOL でコ ンソールのリダイレクトを使用するには、コンソー ル
オプション 説明 Remote Terminal Type (リモートターミナルの タイプ) (デフォルトは VT100/VT220) リモートコンソールのターミナルタイプを VT100/VT220 または ANSI に設定します。 Redirection After Boot OS の読み込み時に BIOS コンソールのリダイレク (起動後のリダイレクト) トを有効または無効にします。 (デフォルトは Enabled (有効)) Embedded Server Management(組み込みサーバー管理)画面 オプション 説明 Front Panel LCD オプションは、User Defined String(ユーザー定義のス Options(前面パ トリング)、Model Number(モデル番号)、または None ネル LCD オプ (なし)です。 ション) LCD ホームの画面を以上の 3 つのオプション以外に設定す ると、オプションは BIOS に Advanced(詳細)として表 示されます。この場合、BIOS 内のオプションを変更するに は、別の LCD 設定ユーティリティ(i
Power Management(電力の管理)画面 オプション Power Management (電力の管理) (デフォルトは OS Control (OS 制御)) 説明 オプションは、OS Control(OS 制御)、Active Power Controller(アクティブパワーコントローラ) 、Custom (カスタム) 、または Maximum Performance(最大パ フォーマンス)です。Custom(カスタム)設定以外のすべ ての設定では、BIOS はこの画面の電源オプションを次のよ うにあらかじめ設定します。 • OS Control(OS 制御)では、CPU 電源が OS DBPM に、 ファン電源が Minimum Power(最小電力)に、メモリ電 源が Maximum Performance(最大パフォーマンス)に設 定されます。この設定では、プロセッサのパフォーマンス情 報のすべてが制御のためにシステム BIOS から OS に渡されま す。OS は、プロセッサのパフォーマンスをプロセッサの使 用率に基づいて設定します。 • Active Power Controller
オプション 説明 Memory Power オプションは、Maximum Performance(最大パ and フォーマンス)、設定周波数、または Minimum Power Performance (最小電力)です。 Management (メモリ電源およ びパフォーマン ス管理) System Security(システムセキュリティ)画面 オプション 説明 System Password パスワードセキュリティ機能の現在のステータスを (システムパスワード) 表示し、新しいシステムパスワードの設定と検証が できます。 メモ:詳細については、81 ページの「システムパス ワードの使い方」を参照してください。 Setup Password(セッ トアップパスワード) セットアップパスワードを使用してセットアップ ユーティリティへのアクセスを制限します。 メモ:詳細については、81 ページの「システムパス ワードの使い方」を参照してください。 Password Status(パス ワードステータス) (デフォルトは Unlocked (ロック解除)) Setup Password(セットアップ
オプション 説明 システムの Trusted Platform Module(TPM)(信頼 済みプラットフォームモジュール)のレポートを設 定します。 TPM Security (TPM セキュリティ) (デフォルトは Off (オフ)) Off(オフ)に設定すると、TPM の存在が OS に報告 されません。 On with Pre-boot Measurements(起動前測定あ りでオン)に設定すると、TPM が OS に報告され、 POST 中に起動前測定が TPM に保存されます。 On without Pre-boot Measurements(起動前測 定なしでオン)に設定すると、TPM が OS に報告さ れ、起動前測定は省略されます。 TPM Activation (TPM の有効化) (デフォルトは No Change(変更なし)) Activate(有効にする)に設定すると、TPM がデ フォルト設定の状態で有効になります。Deactivate (無効にする)に設定すると、TPM は無効になりま す。No Change(変更なし)状態の場合、処理は何 も実行されません。TPM
オプション NMI Button (NMI ボタン) (デフォルトは Disabled(無効) ) 説明 注意:TPM をクリアすると、TPM 内のすべて の暗号化キーが失われます。このオプションを 選択すると OS からの起動ができなくなり、暗 号化キーが復元できない場合はデータが失われ ます。このオプションを有効にする前に TPM キーをバックアップしてください。 NMI 機能の有効 / 無効を切り替えます。 AC Power Recovery (AC 電源の回復) (デフォルトは Last (直前)) AC Power Recovery Delay(AC 電源リカバ リ遅延) (デフォルトは Immediate(即時)) 電源回復時のシステムの動作を設定します。Last (直前)に設定されている場合、システムは電源が中 断される直前の電源状態に戻ります。On(オン) では電源回復時にシステムの電源が入ります。Off (オフ)では、電源が回復してもシステムの電源は切 れたままです。 電源回復後にシステムが起動するタイミングを設定 します。オプションは、Immediate(即時) 、 Random
Exit(終了)画面 セットアップユーティリティを終了するには を押します。Exit (終了)画面には次のオプションが表示されます。 • Save Changes and Exit(変更を保存して終了) • Discard Changes and Exit(変更を破棄して終了) • Return to Setup(セットアップへ戻る) UEFI ブートマネージャの起動 メモ:UEFI 起動モードからインストールする OS は 64 ビット UEFI 対応 (Microsoft Windows Server 2008 x64 バージョンなど)である必要があり ます。DOS および 32 ビットの OS は BIOS 起動モードからのみインストー ルできます。 メモ:UEFI ブートマネージャにアクセスするには、セットアップユー ティリティで Boot Mode(起動モード)を UEFI に設定する必要があ ります。 UEFI ブートマネージャでは次の操作ができます。 • 起動オプションの追加、削除、配置。 • 再起動なしでのセットアップユーティリティオプションおよび BIOS レベル起
UEFI ブートマネージャのナビゲーションキーの使い方 キー 動作 上矢印 前のフィールドに移動し、そのフィールドを ハイライト表示します。 下矢印 次のフィールドに移動し、そのフィールドを ハイライト表示します。 スペースバー、、<+>、フィールド内の設定値を順に切り替えます。 <–> UEFI ブートマネージャの画面を更新するか、 または別のプログラムの画面から UEFI ブー トマネージャの画面に戻ります。 UEFI ブートマネージャのヘルプファイルを表 示します。 UEFI Boot Manager(UEFI ブートマネージャ)画面 オプション 説明 Continue(続行) システムは起動順序の先頭にあるデバイスから順に 起動を試みます。起動が失敗すると、システムは起 動順序内の次のデバイスから起動を試みます。起動 が成功するか、起動オプションがなくなるまで処理 は続行されます。 < 起動オプション > 使用可能な起動オプション(アスタリスク [*] 付 き)のリストが表示されます。使用する起動オプ ションを選択し、 を
UEFI Boot Settings(UEFI 起動設定)画面 オプション 説明 Add Boot Option(起動 新しい起動オプションを追加します。 オプションの追加) Delete Boot Option 既存の起動オプションを削除します。 (起動オプションの削除) Enable/Disable Boot 起動オプションリスト内のオプションの有効 / 無効 Option(起動オプション を切り替えます。 の有効 / 無効) Change Boot Order (起動順序の変更) One-Time Boot From File(ファイルからの 1 回限りの起動) 起動オプションリストの順序を変更します。 起動オプションリストに含まれていない 1 回限りの 起動オプションを設定します。 System Utilities(システムユーティリティ)画面 オプション 説明 System Setup(セット 再起動なしでセットアップユーティリティにアクセ アップユーティリティ) スします。 System Services (システムサービス) システムが再起動し、Lifecycle Controll
システムパスワードとセットアップ パスワードの機能 メモ:パスワードを忘れた場合は、203 ページの「拡張カードライザー ボードのコンポーネントおよび PCIe バス」を参照してください。 お使いのシステムは、出荷時にはシステムパスワード機能が有効になって いません。システムパスワードによる保護を必ず有効にしてシステムを操 作してください。 注意:パスワード機能は、システム内のデータに対して基本的なセキュ リティを提供します。 注意:システムが無人で稼動中の場合は、システムに格納されている データにだれでもアクセスできます。 システムパスワードの使い方 システムパスワードを設定すると、起動後にシステムパスワードの入力を 求めるプロンプトが表示されます。 システムパスワードの設定 システムパスワードを設定する前に、まずセットアップユーティリティを 起動して、System Password(システムパスワード)オプションを確認 します。 システムパスワードが設定されている場合、System Password(システ ムパスワード)は Enabled(有効)です。Password Status(パスワー ドステ
システムパスワードが設定されておらず、システム基板上のパスワード ジャンパが有効の位置に設定されている場合、System Password(シス テムパスワード)は Not Enabled(無効)で Password Status(パス ワードステータス)は Unlocked(ロック解除)です。システムパス ワードを設定するには、次の手順を実行します。 1 Password Status(パスワードステータス)が Unlocked(ロック 解除)に設定されていることを確認します。 2 System Password(システムパスワード)オプションをハイライ ト表示して、 を押します。 3 新しいシステムパスワードを入力します。 パスワードは半角の英数字で 32 文字まで入力できます。 フィールドには、入力した文字の代わりに「*」が表示されます。 パスワードの設定では、大文字と小文字は区別されません。無効な キーの組み合わせもあります。無効な組み合わせで入力すると、 ビープ音が鳴ります。文字を削除するには、 または左 矢印キーを押します。 メモ:システムパスワードの設定を途中
システムを保護するためのシステムパスワードの使い方 メモ:セットアップパスワードを設定している場合(84 ページの「セッ トアップパスワードの使い方」を参照)、システムはセットアップパス ワードをシステムパスワードの代用として受け付けます。 Password Status(パスワードステータス)が Unlocked(ロック解除) に設定されている場合は、パスワードセキュリティを有効のままにしてお くことも無効にすることもできます。 パスワードセキュリティを有効にするには、次の手順を実行します。 1 システムの電源を入れるか、または を押して システムを再起動します。 2 パスワードを入力し、 を押します。 パスワードセキュリティを無効にするには、次の手順を実行します。 1 システムの電源を入れるか、または を押して システムを再起動します。 2 パスワードを入力し、 を押します。 Password Status(パスワードステータス)が Locked(ロック)に設 定されている場合は、再起
既存のシステムパスワードの削除または変更 1 セットアップユーティリティを起動して、System Security(シス テムセキュリティ)を選択します。 2 Setup Password(セットアップパスワード)をハイライト表示し、 を押してセットアップパスワードウィンドウを開きます。 を 2 回押して、既存のセットアップパスワードをクリアし ます。 設定が Not Enabled(無効)に変わります。 3 新しいセットアップパスワードを設定する場合は、84 ページの 「セットアップパスワードの設定」の手順を実行します。 セットアップパスワードの使い方 セットアップパスワードの設定 セットアップパスワードは、Setup Password(セットアップパスワー ド)が Not Enabled(無効)に設定されている場合にのみ設定できま す。セットアップパスワードを設定するには、Setup Password(セッ トアップパスワード)オプションをハイライト表示して、<+> または <–> キーを押します。パスワードの入力と確認を求めるプロンプトが表示され ます。 メモ:セッ
セットアップパスワード使用中の操作 Setup Password(セットアップパスワード)が Enabled(有効)に設 定されている場合、正しいセットアップパスワードを入力しないと、ほと んどのセットアップオプションは変更できません。 3 回までの入力で正しいパスワードを入力しないと、セットアップユー ティリティの画面は表示されますが、変更することはできません。次のオ プションは例外です。System Password(システムパスワード)が Enabled(有効)に設定されておらず、Password Status(パスワード ステータス)オプションを通じてロックされていない場合は、システムパ スワードを設定できます。既存のシステムパスワードは、無効にすること も変更することもできません。 メモ:Setup Password(セットアップパスワード)オプションと Password Status(パスワードステータス)オプションを併用すると、無許可の変更 からシステムパスワードを保護することができます。 既存のセットアップパスワードの削除または変更 1 セットアップユーティリティを起動して、System
組み込みシステム管理 Lifecycle Controller は内蔵されているユーティリティで、サーバーのラ イフサイクル中、システムとストレージの管理タスクを組み込み環境から 実行できるようにします。 Lifecycle Controller は起動中に開始でき、OS に依存せずに機能すること ができます。 メモ:一部のプラットフォーム構成では、Lifecycle Controller の提供する 機能の一部がサポートされない場合があります。 Lifecycle Controller のセットアップ、ハードウェアとファームウェアの 設定、および OS の導入の詳細については、 support.dell.
BMC セットアップモジュールの起動 1 システムの電源を入れるか、再起動します。 2 POST 後、プロンプトが表示されたときに、 を押します。 を押す前に OS のロードが開始された場合は、システムの 起動が完了するのを待ってから、もう一度システムを再起動し、こ の手順を実行してください。 iDRAC6 設定ユーティリティ iDRAC6 設定ユーティリティは、オプションの iDRAC6 および管理下サー バーのパラメータを表示および設定できる起動前の設定環境です。 iDRAC6 設定ユーティリティには以下の機能があります。 • 障害の記録と SNMP 警告を有効にする。 • システムイベントログとセンサーステータスへのアクセスを 提供する。 • 電源オンとオフを含むシステム機能の制御を可能にする。 • システムの電力状態や OS に依存せずに機能する。 さらに、iDRAC6 設定ユーティリティでは以下の操作もできます。 • 専用の iDRAC6 Enterprise カードポートまたは内蔵 NIC1 を介して、 iDRAC6 LAN を設定したり、
iDRAC6 設定ユーティリティの起動 1 システムの電源を入れるか、再起動します。 2 POST 中に画面の指示に従って を押します。 を押す前に OS のロードが開始された場合は、システムの 起動が完了するのを待ってから、もう一度システムを再起動し、こ の手順を実行してください。 88 セットアップユーティリティと UEFI ブートマネージャの使い方
システム部品の取り付け メモ:お使いのシステムには、構成に応じて、ホットスワップ対応また はケーブル接続式のハードドライブ、冗長または非冗長電源ユニット、お よび LCD パネルまたは診断インジケータが取り付けられています。本項の イラストは、ホットスワップ対応ハードドライブと LCD パネルを搭載した システムを示しています。 奨励するツール • システムキーロックのキー • #1 および #2 のプラスドライバ • トルクスドライバ • 静電気防止用リストバンド システムの内部 警告:システムを持ち上げる必要がある場合は、必ずだれかの手を借り てください。けがを防ぐため、決してシステムを一人で持ち上げようとし ないでください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマ
図 3-1 システムの内部 2 1 3 4 12 5 11 10 6 7 9 8 90 1 電源ユニットエアフローカバー 2 システム基板エアフローカバー 3 電源ユニットベイ(2) 4 拡張カードライザー 5 ヒートシンク / プロセッサ(2) 6 メモリモジュール(8) 7 システム冷却ファン(4) 8 オプティカルドライブ 9 ハードドライブ(4) 10 コントロールパネルボード 11 SAS バックプレーン 12 電源ユニット冷却ファン(2) システム部品の取り付け
前面ベゼル(オプション) 前面ベゼルの取り外し 1 ベゼルの左端のキーロックを解除します。 2 キーロックの横にあるリリースラッチを押し上げます。 3 ベゼルの左端を前面パネルと反対の方向へ動かします。 4 ベゼル右端のフックを外し、ベゼルをシステムから取り外します。 図 3-2 を参照してください。 図 3-2 前面ベゼルの取り外しと取り付け 3 2 1 4 1 リリースラッチ 2 キーロック 3 ベゼル 4 ヒンジタブ 前面ベゼルの取り付け 1 ベゼルの右端をシャーシに取り付けます。 2 ベゼルの左端をシステムに取り付けます。 3 キーロックでベゼルを固定します。図 3-2 を参照してください。 システム部品の取り付け 91
システムカバーの取り外しと取り付け 警告:システムを持ち上げる必要がある場合は、必ずだれかの手を借り てください。けがを防ぐため、決してシステムを一人で持ち上げようとし ないでください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 メモ:システム内部のコンポーネントの取り外しや取り付けを行う際に は、静電マットと静電ストラップを常に使用することをお勧めします。 システムカバーの取り外し 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 ラッチリリースロックを反時計方向に回してロック解除位置にしま す。図 3-3 を参照してください。 3 ラッチリリースロック
図 3-3 システムカバーの取り外しと取り付け 1 2 1 ラッチリリースロック 2 くぼみ システムカバーの取り付け 1 カバーをシャーシ上に置き、所定の位置に収まるまでシャーシの後 方にわずかにずらします。図 3-3 を参照してください。 2 所定の位置にカチッとはまるまで、カバーをシャーシの前方にスラ イドさせます。 3 ラッチリリースロックを時計方向に回してカバーを固定します。 4 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 システム部品の取り付け 93
ハードドライブ お使いのシステムには、ケーブル接続式の内蔵ドライブか、または、3.5 インチホットスワップ対応ハードドライブキャリアに 3.5 インチ(SAS ま たは SATA)または 2.
図 3-4 ハードドライブダミーの取り外しと取り付け 1 2 1 ハードドライブダミー リリースレバー 2 ハードドライブダミーの取り付け 1 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し」を参照してください。 2 リリースボタンが所定の位置に固定されるまで、ドライブダミーを ドライブベイに挿入します。 3 前面ベゼルを取り外した場合は、取り付けます。91 ページの「前面 ベゼルの取り付け」を参照してください。 ハードドライブキャリアの取り外し 注意:お使いの OS がホットスワップ対応ドライブの取り付けをサポート していることを確認してください。OS に付属のマニュアルを参照してく ださい。 1 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベ ゼルの取り外し」を参照してください。 2 管理ソフトウェアから、ドライブを取り外す準備をします。ドライ ブキャリアのハードドライブインジケータが、ドライブを安全に取 り外すことができるという信号を発するまで待ちます。ホットス ワップ対応ドライブを取り外す手順の詳細については、コントロー ラのマニュアルを参
ドライブがオンラインだった場合は、ドライブの電源が切れる際に、 緑色のアクティビティ / 障害インジケータが点滅します。ドライブイ ンジケータが消灯したら、ドライブを安全に取り外すことがで きます。 3 ハードドライブキャリア前面のリリースボタンを押して、ハンドル を開きます。 4 ドライブベイから外れるまで、ハードドライブキャリアを手前に引 き出します。図 3-5 を参照してください。 注意:システムの正常な冷却状態を維持するために、空のハードドライ ブベイすべてにドライブダミーを取り付ける必要があります。 5 ドライブダミーを空のドライブベイに挿入します。95 ページの 「ハードドライブダミーの取り付け」を参照してください。 6 前面ベゼルを取り外した場合は、取り付けます。91 ページの「前面 ベゼルの取り付け」を参照してください。 図 3-5 ハードドライブキャリアの取り外しと取り付け 1 3 2 96 1 リリースボタン 3 ハードドライブキャリア システム部品の取り付け 2 ハードドライブキャリアハンドル
ハードドライブキャリアの取り付け 注意:SAS/SATA バックプレーン用として使用が認められているテスト済 みのハードドライブのみを使用してください。 注意:ハードドライブを取り付ける際は、隣接するドライブが完全に装 着されていることを確認します。ハードドライブキャリアを挿入し、完全 に装着されていないキャリアの隣のハンドルをロックしようとすると、完 全に装着されていないキャリアのシールドのバネが損傷し、使用できなく なるおそれがあります。 注意:お使いの OS がホットスワップ対応ドライブの取り付けをサポート していることを確認してください。OS に付属のマニュアルを参照してく ださい。 注意:1 つのシステム構成内で SATA ハードドライブと SAS ハードドライ ブを組み合わせることはできません。 1 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し」を参照してください。 2 ベイにドライブダミーが取り付けられている場合は、取り外します。 94 ページの「ハードドライブダミーの取り外し」を参照してく ださい。 3 ハードドライブキャリア前面のリリースボタンを押して、ハン
ハードドライブをハードドライブキャリアから取り外す方法 ハードドライブキャリアのスライドレールからネジを外し、ハードドライ ブをキャリアから離します。図 3-6 を参照してください。 図 3-6 ハードドライブキャリアへのハードドライブの取り付けと取り外し 2 1 4 3 1 ネジ(4) 2 ハードドライブ 3 SAS/SATA のネジ穴 4 ハードドライブキャリア ハードドライブをハードドライブキャリアに取り付ける方法 1 コネクタ側を後部に向けて、ハードドライブをハードドライブキャ リアに挿入します。図 3-6 を参照してください。 2 ハードドライブのネジ穴をハードドライブキャリアの後部の穴に合 わせます。 3 4 本のネジを取り付けて、ハードドライブをハードドライブキャリ アに固定します。 98 システム部品の取り付け
ケーブル接続式ハードドライブの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことがで きます。製品マニュアルで許可されている範囲に限り、またはオンライン サービスもしくはテレホンサービスとサポートチームの指示によってのみ、 トラブルシューティングと簡単な修理を行うようにしてください。デルで 認められていない修理(内部作業)による損傷は、保証の対象となりませ ん。製品に付属しているマニュアルの「安全にお使いいただくために」を お読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 データ / 電源ケーブルとデータケーブルをドライブベイ内のハードド ライブから外します。 4 ハードドライブブラケット上の青いドットのあるタブを引き上げ、 ドライブをベイから引き出します。図 3-7 を参照してください。 図 3-7 ケーブル接続式ハードドライブの取り外しと取り付け 2 1 3 4 1 ハードドライブ 2
メモ:ハードドライブを取り付けない場合は、ドライブブラケットから ドライブを取り外し(図 3-8 を参照)、空のブラケットをドライブベイに挿 入します。 5 システムカバーを取り付けます。93 ページの「システムカバーの取 り付け」を参照してください。 ケーブル接続式ハードドライブの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、 システムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 既存のハードドライブブラケットを取り外します。ブラケット上の 青いドットのあるタ
7 システムカバーを取り付けます。93 ページの「システムカバーの取 り付け」を参照してください。 8 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 9 セットアップユーティリティを起動し、ハードドライブのコント ローラが有効になっていることを確認します。62 ページの「セット アップユーティリティの起動」を参照してください。 10 セットアップユーティリティを終了し、システムを再起動します。 ドライブの動作に必要なソフトウェアをインストールする手順につ いては、ハードドライブに付属のマニュアルを参照してください。 ハードドライブをハードドライブブラケットから取り外す方法 ハードドライブブラケットのスライドレールからネジを外し、ハードドラ イブをブラケットから離します。図 3-8 を参照してください。 図 3-8 ハードドライブブラケットへのハードドライブの取り付けと取り外し 1 2 3 4 1 ネジ(4)* 2 ハードドライブ 3 SAS/SATA のネジ穴 4 ハードドライブブラケット * ネジは、デルからご購入いただいたハードド
ハードドライブをハードドライブブラケットに取り付ける方法 1 コネクタ側を後部に向けて、ハードドライブをハードドライブブラ ケットに挿入します。図 3-8 を参照してください。 2 ハードドライブの穴をハードドライブブラケットの後部の穴に合わ せます。 正しく揃うと、ハードドライブの背面がハードドライブブラケット の背面と同一面に揃います。 3 4 本のネジを取り付けて、ハードドライブをハードドライブブラ ケットに固定します。 オプティカルドライブ オプションの DVD-ROM または DVD+/-RW オプティカルドライブは、前 面パネルに挿入し、システム基板上の SATA コネクタに接続します。 メモ:DVD デバイスはデータ専用。 オプティカルドライブの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ませ
5 ドライブを取り外すには、リリースラッチを引いてドライブを傾け るようにして持ち上げ、金属製突起の切り込みから外します。ドラ イブを持ち上げてシャーシから取り出します。図 3-9 を参照してく ださい。 6 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 7 前面ベゼルを取り外した場合は、取り付けます。91 ページの「前面 ベゼルの取り付け」を参照してください。 システム部品の取り付け 103
図 3-9 オプティカルドライブの取り外しと取り付け 1 2 3 4 7 5 6 104 1 データケーブル 2 電源ケーブル 3 オプティカルドライブ 4 リリースラッチ 5 金属製突起(2) 6 切り込み(2) 7 切り込みのある金属製突起(2) システム部品の取り付け
オプティカルドライブの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し」を参照してください。 2 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 3 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 4 シャーシの金属製突起の 2 つの切り込みをドライブの穴に合わせま す。図 3-9 を参照してください。 5 リリースラッチを引き、オプティカルドライブを所定の位置に置い てから、リリースラッチを放します。 6 ドライブの背面に電源ケーブル
電源ユニット お使いのシステムは次の電源ユニットモジュールをサポートしています。 • 480 W(非冗長電源ユニット) • 500 W(冗長電源ユニット) 電源ユニットを 2 台取り付ける場合、2 台目の電源ユニットはホットス ワップ対応の冗長電源となります。冗長モードでは、効率を最大限に高め るために両方の電源ユニットに電力負荷が分散されます。システムの電源 が入った状態で 1 台の電源ユニットを取り外すと、もう 1 台の電源ユ ニットが電力負荷をすべて引き受けます。 冗長電源ユニットの取り外し 注意:システムが正常に動作するには、電源ユニットが 1 台は必要です。 冗長電源が装備されたシステムでも、電源が入った状態で一度に取り外 し、取り付けができる電源ユニットは、1 台だけです。 1 電源から電源ケーブルを外します。 2 電源ユニットから電源ケーブルを外し、システムケーブルを束ねて 固定しているベルクロストラップを外します。 メモ:電源ユニットの取り外しに支障がある場合は、ラッチを外し てオプションのケーブルマネージメントアームを持ち上げる必要が あります。ケーブルマネージメントアームの詳細に
図 3-10 冗長電源ユニットの取り外しと取り付け 1 2 3 1 電源ユニット 3 ケーブル保持ブラケット 2 ロックタブ 冗長電源ユニットの取り付け 1 両方の電源ユニットのタイプと最大出力電力が同じであることを確 認します。 メモ:最大出力電力(ワット数で表記)は電源ユニットラベルに記 載されています。 2 電源ユニットダミーが取り付けられている場合は、取り外します。 108 ページの「電源ユニットダミーの取り外し」を参照してく ださい。 3 新しい電源ユニットをシャーシに挿入し、完全に固定されてリリー スラッチがカチッとロックするまで押し込みます。図 3-10 を参照し てください。 メモ:前の手順の 手順 1 でケーブルマネージメントアームのラッチ を外した場合は、再びラッチをかけます。ケーブルマネージメント アームの詳細については、システムのラックに関するマニュアルを 参照してください。 システム部品の取り付け 107
4 電源ケーブルを電源ユニットに接続し、電源ケーブルのプラグをコ ンセントに差し込みます。 注意:電源ケーブルを接続する際には、ケーブルをベルクロストラップ で固定してください。 メモ:2 台の電源ユニットがあるシステムに新しい電源ユニットの通常の 取り付けや、ホットスワップまたはホットアッドによって交換または取り 付けを行う際には、システムが電源を認識して状態を判断するまで数秒待 ちます。電源ユニットステータスインジケータが緑色に点灯すれば、電源 ユニットは正常に機能しています。図 1-6 を参照してください。 電源ユニットダミーの取り外し 2 台目の電源ユニットを取り付ける場合は、電源ユニットダミーを外側へ 引いて、ベイ PS2 から取り外します。 注意:非冗長構成の場合は、システムの正常な冷却状態を維持するため に、電源ユニットベイ PS2 に電源ユニットダミーを取り付ける必要があり ます。電源ユニットダミーは、2 台目の電源ユニットを取り付ける場合に のみ取り外してください。 電源ユニットダミーの取り付け メモ:電源ユニットダミーは必ず電源ユニットベイ PS2 に取り付けてく ださい。 電源ユニッ
2 システムケーブルを束ねて固定しているベルクロストラップを外し ます。 メモ:電源ユニットの取り外しに支障がある場合は、ラッチを外し てオプションのケーブルマネージメントアームを持ち上げる必要が あります。ケーブルマネージメントアームの詳細については、シス テムのラックに関するマニュアルを参照してください。 メモ:システムケーブルを固定している電源ケーブル固定ブラケッ トを外します。詳細については、システムに付属の『はじめに』を 参照してください。 3 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 4 電源ユニットからシステム基板、ハードドライブ、オプティカルド ライブに接続されている電源ケーブルをすべて外します。図 3-11 を 参照してください。 5 電源ユニットをシャーシに固定しているネジを緩め、電源ユニット を持ち上げてシャーシから取り外します。図 3-11 を参照してくだ さい。 システム部品の取り付け 109
図 3-11 非冗長電源ユニットの取り外しと取り付け 2 1 6 3 5 4 110 1 電源ユニット 2 ネジ 3 8 ピン電源ケーブル 4 ODD 電源ケーブル 5 24 ピン電源ケーブル 6 SATA 電源ケーブル システム部品の取り付け
非冗長電源ユニットの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 電源ユニットをシャーシの上に置きます。図 3-11 照してください。 ネジを締めて電源ユニットをシャーシに固定します。 4 すべての電源ケーブルをシステム基板、ハードドライブ、オプティ カルドライブに接続します。 5 システムカバーを取り付けます。93 ページの「システムカバーの取 り付け」を参照してください。 6 電源ケーブルを電源ユニットに
• PCI Express Generation 2 の拡張カードは、このスロットでサポート されています。 注意:冷却効果を確保するには、内蔵ストレージコントローラを除いて、 2 枚の拡張カードのうち、消費電力が 15 W を超えるものは 1 枚のみ(25 W まで)としてください。 • 冷却効果が確保され機械的にも適合するように拡張カードを取り付 けるためのガイドを 表 3-1 に示します。表に示すスロットの優先順 位に従って、優先度の最も高い拡張カードを最初に取り付ける必要 があります。その他すべての拡張カードは、カードの優先順位とス ロットの優先順位に従って取り付けてください。 表 3-1 拡張カードの取り付け順序 カードの優先 カードのタイプ 順位 スロットの 可能な 優先順位 枚数 25 W の カード 1 SAS 6/iR モジュラー 2 1 可 2 HPCC 1 1 可 3 ファイバーチャネル 1 1 可 4 10 Gb NIC 1 1 可 5 その他すべての Dell ストレージ 1 カード 1 可 6 その他すべての NIC
拡張カードの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 カードからすべてのケーブルを外します。 4 拡張カードラッチを引き出します。図 3-12 を参照してください。 5 拡張カードの端をつかんで、拡張カードコネクタから慎重に取り外 します。 6 カードを取り外したままにしておく場合は、シャーシの空の拡張 カードスロットに金属製のフィラーブラケットを取り付けます。 メモ:FCC(Federal Commun
拡張カードの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 拡張カードをパッケージから取り出し、取り付けの準備をします。 手順については、カードに付属のマニュアルを参照してください。 2 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 3 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 4 拡張カードラッチを開き、フィラーブラケットを取り外します。 図 3-12 を参照してください。 5 カードの両端を持って、カードエッジコネクタを拡張カードライ ザーの拡張カードコネクタに合わせます。 6 カードエッジコネクタを
図 3-12 拡張カードの取り外しと取り付け 3 1 2 1 拡張カードラッチ 3 拡張カードライザー 2 拡張カード 8 拡張カードにすべてのケーブルを接続します。 9 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 10 カードのマニュアルに従って、必要なすべてのデバイスドライバを インストールします。 システム部品の取り付け 115
内蔵ストレージコントローラカード お使いのシステムには、拡張カードライザーに内蔵 SAS または PERC コ ントローラカード専用の拡張カードスロットがあります。このカードは、 システムの内蔵ハードドライブに内蔵ストレージサブシステムを提供する ものです。コントローラは SAS ハードドライブと SATA ハードドライブ をサポートしており、ハードドライブを RAID 構成に設定できます。設定 可能な RAID の種類は、システムに搭載されているストレージコントロー ラのバージョンに応じて異なります。 内蔵ストレージコントローラカードの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接
図 3-13 内蔵ストレージコントローラカードの取り外しと取り付け 1 2 3 4 5 1 SAS データケーブルコネクタ 2 ストレージコネクタ 3 拡張カードライザー 4 内蔵ストレージコントローラ カード 5 リリースレバー(青色) 内蔵ストレージコントローラカードの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 システム部品の取り付け 117
3 必要であれば、拡張カードを取り外します。116 ページの「内蔵ス トレージコントローラカード」を参照してください。 4 カードの両端を持ち、カードが完全に装着されるまで、SLOT 2 とラ ベル表示されたライザー上の拡張カードコネクタにカードエッジコ ネクタをしっかりと挿入します。 5 SAS データケーブルコネクタを内蔵ストレージコントローラカード に接続します。図 3-13 を参照してください。 メモ:ケーブルは、必ずケーブルのコネクタラベルの表記に従って 接続してください。ケーブルを逆方向に取り付けると機能しません。 6 SAS データケーブルをシャーシ内側のチャネルに通します。 7 「SAS A」とラベル表示されたコネクタをバックプレーンのコネクタ SAS A に、「SAS B」とラベル表示されたコネクタをバックプレーン のコネクタ SAS B に接続します。図 3-13 を参照してください。 8 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 拡張カードライザー システムの拡張カードライザーは、x16 リンク Gen2 PCIe 拡張カードを サ
3 拡張カードスロットに拡張カードが取り付けられている場合は、取 り外します。 113 ページの「拡張カードの取り外し」を参照してください。 4 内蔵ストレージコントローラカードが取り付けられている場合は、 取り外します。116 ページの「内蔵ストレージコントローラカード の取り外し」を参照してください。 5 ライザーにケーブルが取り付けられている場合は、すべて外します。 6 拡張カードライザーを取り外すには、ライザーガイドをつかんで、 拡張カードライザーをシャーシから持ち上げます。図 3-14 を参照し てください。 システム部品の取り付け 119
図 3-14 拡張カードライザーの取り外しと取り付け 3 2 1 4 5 6 1 ライザーガイド(2) 2 拡張カードライザー 3 拡張カードスロット 4 ライザーガイドポスト(2) 6 内蔵ストレージコントローラス ロット 5 120 拡張カードライザーソケット (2) システム部品の取り付け
拡張カードライザーの取り付け 1 拡張カードライザーを取り付けるには、ライザーガイドをシステム 基板上のライザーガイドポストに合わせます。図 3-14 を参照してく ださい。 2 拡張カードライザーを所定の位置に下ろし、拡張カードライザーコ ネクタが完全に装着されるまでしっかり挿入します。 3 内蔵ストレージコントローラカードを取り外した場合は、取り付け ます。117 ページの「内蔵ストレージコントローラカードの取り付 け」を参照してください。 4 必要に応じて、取り外した拡張カードを取り付けます。114 ページ の「拡張カードの取り付け」を参照してください。 5 必要に応じて、ライザーにケーブルを接続します。 6 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 内蔵 USB メモリキー USB メモリキーは、起動デバイス、セキュリティキー、または大容量ス トレージデバイスとして使用できます。内部 USB コネクタを使用するに は、セットアップユーティリティの Integrated Devices(内蔵デバ イス)画面で Internal USB Port(内部
メモ:他のコンポーネントとの干渉を避けるために、USB キーの最大サ イズは横幅 24 mm x 奥行き 79 mm x 縦幅 8.
システム基板エアフローカバー システム基板エアフローカバーは、プロセッサ、ヒートシンク、およびメ モリモジュールをカバーし、これらのコンポーネントを通気によって冷却 します。冷却ファンモジュールによって通気が促され、システム基板エア フローカバーによって、これらのコンポーネントに空気が流れます。 システム基板エアフローカバーの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 注意:システム基板エアフローカバーを取り外した状態でシステムを使 用しないでください。システムがすぐにオーバーヒートしてシャットダウ ンし、データが失われるおそれがあります。 1 システムカバーを開きます。92 ページの「システムカバー
図 3-16 システム基板エアフローカバーの取り外しと取り付け 1 2 1 システム基板エアフローカ バー 2 エアフローカバータブ(2) システム基板エアフローカバーの取り付け 1 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 2 番号が付いたファンベイの中央をガイドとして使ってエアフローカ バーの位置を合わせ、3 番のファンモジュールの左側にあるタブプ ロジェクションの位置を確認します。図 3-16 を参照してください。 3 すべてのタブがスロットに入り、エアフローカバーがシステム基板 に固定されるまで、システム基板エアフローカバーを押し下げます。 4 システム基板エアフローカバー上のケーブルホルダにケーブルを適 切に配線します。 5 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 124 システム部品の取り付け
配電基板エアフローカバー 配電基板エアフローカバーは配電基板を覆い、電源ユニットを通気によっ て冷却します。冷却ファンモジュールによって通気が促され、配電基板エ アフローカバーによって、電源ユニットに空気が流れます。 配電基板エアフローカバーの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 注意:配電基板エアフローカバーを取り外した状態でシステムを使用し ないでください。システムがすぐにオーバーヒートしてシャットダウン し、データが失われるおそれがあります。 1 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 2 エアフローカバーの端(青色のタブの近く)をつかみ
配電基板エアフローカバーの取り付け 1 番号付きのファンベイ 5 と 6 の中央をガイドとして使い、配電基板 エアフローカバーを所定の位置に合わせます。図 3-17 を参照してく ださい。 2 システムシャーシ内壁と揃うまで、エアフローカバーを押し下げ ます。 3 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 iDRAC6 Express カード(オプション) iDRAC6 Express カードの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、 システムをコンセントから外します。 2 システムカバ
図 3-18 iDRAC6 Express カードの取り付けまたは取り外し 1 2 3 4 1 iDRAC6 Express カード 2 切り込み 3 クリップ 4 プラスチック製の突起タブ iDRAC6 Express カードの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 iDRAC6 Express カードの切り込みをシステム基板上のクリップに挿 入します。 システム部品の取り付
4 カードの前端をシステム基板上のコネクタに合わせます。コネクタ の位置については、図 6-1 を参照してください。 5 完全に装着されるまで、カードを押し下げます。図 3-18 を参照して ください。 カードの前端が所定の位置に収まると、プラスチック製の突起タブ がホルダの前端部にカチッとはまります。 6 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 7 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 iDRAC6 Enterprise カード(オプション) iDRAC6 Enterprise カードの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」
6 カードの前端にある 2 つのタブをわずかに後方へ引き、カードの前 端を保持突起から注意深く外します。 カードが突起から外れると、カードの下のコネクタがシステム基板 コネクタから外れます。 7 RJ-45 コネクタが背面パネルから完全に離れるまで、システムの背面 からカードを引き抜き、システムから取り出します。 8 システムの背面パネルのポートにプラスチック製フィラープラグを 取り付けます。ポートの位置については、18 ページの「背面パネル の機能およびインジケータ」を参照してください。 9 システム基板エアフローカバーを取り付けます。124 ページの「シ ステム基板エアフローカバーの取り付け」を参照してください。 10 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 11 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 システム部品の取り付け 129
図 3-19 iDRAC6 Enterprise カードの取り外しと取り付け 2 1 3 6 4 5 130 1 iDRAC6 Enterprise カード 2 VFlash メディアスロット 3 VFlash SD カード 4 保持突起ポスト(2) 5 保持突起タブ(2) 6 iDRAC6 Enterprise カードコネクタ システム部品の取り付け
iDRAC6 Enterprise カードの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 システム基板エアフローカバーを取り外します。123 ページの「シ ステム基板エアフローカバーの取り外し」を参照してください。 4 iDRAC6 Enterprise ポートのプラスチック製フィラープラグをシステ ムの背面パネルから取り外します。 5 RJ-45 コネクタが背面パネルの開口部に入る角度にカードを傾けま す。
VFlash メディア(オプション) VFlash メディアカードは SD カードの一種で、システム背面の角にあるオ プションの iDRAC6 Enterprise カードに挿入します。 VFlash メディアカードの取り外し VFlash メディアを取り出すには、カードを押し込んでロックを解除し、 カードスロットから引き出します。 VFlash メディアカードの取り付け 1 システム背面の角にある VFlash メディアスロットの位置を確 認します。 2 ラベル側を上に向けて、SD カードの接続ピン側をモジュールのカー ドスロットに挿入します。 メモ:スロットは正しい方向にしかカードを挿入できないように設 計されています。 3 カードを押し込んでスロットにロックします。 冷却ファン お使いのシステムには 4 台のデュアルモーターファンが備わっており、 プロセッサとメモリモジュールを冷却します。また、冗長電源ユニット用 に 2 台のデュアルモーターファンが備わっています。 メモ:ホットスワップによるファンの取り外しまたは取り付けはサポー トされていません。 メモ:特定のファンに問題が発生した場合には、シ
冷却ファンの取り外し 警告:冷却ファンは、システムの電源を切った後もしばらくは回転し続 けることがあります。システムからの取り外し作業は、ファンの回転が止 まるのを待ってから行ってください。 警告:冷却ファンを取り外した状態でシステムを使用しないでください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 メモ:個々のファンモジュールの取り外し手順は同じです。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 システム基板エアフローカバーまたは配電基板エアフローカバーが
図 3-20 ファンの取り外しと取り付け 1 2 1 ファン 2 電源ケーブル 冷却ファンの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 ファンの向きが正しいことを確認します。 電源ケーブルのある側がシステムの背面を向くようにファンモ ジュールを置きます。 2 ファンモジュールが完全に装着されるまで、ファンアセンブリに挿 入します。図 3-20 を参照してください。 3 ファンの電源ケーブルをシステム基板の電源コネクタに接続します。 134 システム部品の取り付け
4 システム基板エアフローカバーまたは配電基板エアフローカバーを 取り外した場合は、取り付けます。124 ページの「システム基板エ アフローカバーの取り付け」または 126 ページの「配電基板エアフ ローカバーの取り付け」を参照してください。 5 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 RAID バッテリー(オプション) RAID バッテリーの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 メモ:本項の情報は、オプションの PERC コントローラカードが搭載され たシステムにのみ適用されます。 1 システムおよび接続されているすべての周辺機器の電源を切り
図 3-21 RAID バッテリーの取り付けと取り外し 1 2 3 4 136 1 RAID バッテリー 2 バッテリーケーブルコネクタ 3 バッテリーキャリアタブ(2) 4 バッテリーキャリア システム部品の取り付け
RAID バッテリーの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 RAID バッテリーを所定の位置にロックされるまでバッテリーキャリ アに挿入します。図 3-21 を参照してください。 2 バッテリーケーブルをシステム基板のコネクタに接続します。図 6-1 を参照してください。 3 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 4 システムを安定した平面に縦置きにします。 5 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 システムメモリ お使いのシステムは、DDR3 レジスタ DIMM(RDIMM)また
メモリモジュール取り付けの一般的ガイドライン システムの最適なパフォーマンスを実現するには、システムメモリを構成 する際に以下の一般的なガイドラインに従ってください。 メモ:ガイドラインから外れたメモリ構成では、システムが起動しな かったり、ビデオが出力されない場合があります。 • RDIMM と UDIMM を混在させることはできません。 • 使用しないメモリチャネルを除いて、メモリモジュールを装着する メモリチャネルは、すべて同一の構成にする必要があります。 • デュアルプロセッサ構成では、各プロセッサのメモリ構成は同一で なければなりません。 • A1 ~ A4 または B1 ~ B4 に異なるサイズのメモリモジュール(たと えば 2 GB と 4 GB)を混在させることはできますが、メモリモ ジュールを装着するチャネルはすべて同一の構成にする必要があり ます。 • オプティマイザモードを使用する場合、メモリモジュールは A1 また は B1 を先頭とする番号順にソケットに取り付けます。 • クアッドランクのメモリモジュールをシングルまたはデュアルラン クのモジュールと混在させる場
表 3-2 速度に応じたメモリランク装着ガイドライン UDIMM RDIMM 1.35V DIMM 使 最大 GB/ 用時の最速 チャネル (6 コアのみ) DIMM 1 DIMM 2 1.
表 3-3 RDIMM シングル、デュアル、およびクアッドランクのメモリ構成の例 (プロセッサ 1 個あたり) メモリモ ジュール のサイズ 2 GB 4 GB 8 GB 16 GB1 1 メモリソケット シングルプロセッサ デュアルプロセッサ 1 3 2 4 物理メモリ 使用可能な 物理メモリ 使用可能な (GB) メモリ (GB) メモリ (GB) (GB) X 4 2 すべて すべて X 8 4 X X X X X 16 8 X 8 4 すべて すべて X 16 8 X X X X X 32 16 32 X X 16 すべて すべて 64 X X X X 32 64 X X 32 すべて すべて 128 X X X X 64 利用可能な場合。 表 3-4 UDIMM メモリ構成の例(プロセッサ 1 個あたり) メモリモ ジュール のサイズ 1 GB 2 GB 4 GB 140 メモリソケット 1 X X X X X X X X X 3 2 X X X X X X X X X 4 シングルプロセッサ デュアルプロセッサ 物理メモリ 使用可能な 物理メモリ 使用可
メモリモジュールの取り付け 警告:メモリモジュールは、システムの電源を切った後もしばらくは高 温です。メモリモジュールが冷えるのを待ってから作業してください。メ モリモジュールはカードの両端を持ちます。メモリモジュールのコンポー ネントには指を触れないでください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 注意:システムの正常な冷却状態を維持するために、メモリモジュール を取り付けないメモリソケットにはメモリモジュールのダミーカードを取 り付ける必要があります。メモリモジュールのダミーカードは、それらの ソケットにメモリを取り付ける場合にのみ取り外してください。 1 システムおよび接続されているすべての周辺機器
図 3-22 メモリモジュールの取り付けと取り外し 1 2 3 1 メモリモジュール 3 位置合わせキー 2 メモリモジュールソケットのイ ジェクタ(2) 7 メモリモジュールソケットの位置合わせキーにメモリモジュールの エッジコネクタを合わせ、ソケットにメモリモジュールを差し込み ます。 メモ:メモリモジュールソケットには位置合わせキーがあり、メモ リモジュールは一方向にしか取り付けられません。 8 親指でメモリモジュールを押し下げて、メモリモジュールをソケッ トにしっかりはめ込みます。 メモリモジュールがソケットに適切に取り付けられると、メモリモ ジュールソケットのイジェクタがメモリモジュールが装着されてい る別のソケットのイジェクタと同じ位置に揃います。 9 手順 5 ~ 手順 8 を繰り返して、残りのメモリモジュールを取り付け ます。表 3-3 および 表 3-4 を参照してください。 10 システム基板エアフローカバーを取り付けます。124 ページの「シ ステム基板エアフローカバーの取り付け」を参照してください。 142 システム部品の取り付け
11 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 12 システムを起動し、 を押してセットアップユーティリティを起 動し、メインのシステムセットアップ画面の System Memory (システムメモリ)設定を確認します。 システムは新しく増設したメモリを認識して値を変更済みです。 13 値が正しくない場合、1 枚または複数のメモリモジュールが正しく 取り付けられていない可能性があります。手順 2 ~ 手順 12 を繰り 返し、メモリモジュールがソケットにしっかり装着されていること を確認します。 14 システム診断プログラムでシステムメモリのテストを実行します。 195 ページの「内蔵されたシステム診断プログラムの実行」を参照 してください。 メモリモジュールの取り外し 警告:メモリモジュールは、システムの電源を切った後もしばらくは高 温です。メモリモジュールが冷えるのを待ってから作業してください。メ モリモジュールはカードの両端を持ちます。メモリモジュールのコンポー ネントには指を触れないでください。 注意:修理作業の多くは、認定されたサービス技術
4 メモリモジュールソケットの位置を確認します。図 6-1 を参照して ください。 5 メモリモジュールがソケットから飛び出して外れるまで、ソケット の両側にあるイジェクタを押し開きます。図 3-22 を参照してく ださい。 メモリモジュールはカードの端のみを持ちます。端以外の部分には 絶対に触れないでください。 6 システム基板エアフローカバーを取り付けます。124 ページの「シ ステム基板エアフローカバーの取り付け」を参照してください。 7 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 プロセッサ プロセッサの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。
4 システム基板エアフローカバーを取り外します。123 ページの「シ ステム基板エアフローカバーの取り外し」を参照してください。 警告:ヒートシンクとプロセッサは、システムの電源を切った後もしば らくは高温です。ヒートシンクとプロセッサが冷えるのを待ってから作業 してください。 注意:プロセッサを取り外すこと以外の目的で、ヒートシンクをプロ セッサから取り外さないでください。ヒートシンクは適切な温度条件を保 つために必要な部品です。 5 #2 プラスドライバを使用して、ヒートシンク固定ネジのうち 1 本を 緩めます。図 3-23 を参照してください。 6 ヒートシンクとプロセッサの接続が緩むまで、30 秒ほど待ちます。 7 残りのヒートシンク固定ネジを緩めます。 8 ヒートシンクをプロセッサから注意深く持ち上げ、裏返し(サーマ ルグリースが付いた側を上)にして取っておきます。 システム部品の取り付け 145
図 3-23 ヒートシンクの取り外しと取り付け 1 1 ヒートシンク固定ネジ(4) 2 2 ヒートシンク 注意:プロセッサは強い圧力でソケットに固定されています。リリース レバーはしっかりつかんでいないと突然跳ね上がるおそれがありますの で、注意してください。 9 プロセッサのソケットリリースレバーを親指でしっかりと押さえ、 レバーをロック位置から外します。レバーを上方向に 90 度持ち上げ て、プロセッサをソケットから外します。図 3-24 を参照してく ださい。 10 プロセッサシールドのタブを持ち、プロセッサシールドを上方向に 開いて、プロセッサが取り出せる状態にします。図 3-24 を参照して ください。 146 システム部品の取り付け
図 3-24 プロセッサの取り外し 2 3 1 4 1 ソケットリリースレバー 2 プロセッサ 3 プロセッサシールド 4 ZIF ソケット 注意:プロセッサを取り外す際には、ZIF ソケットのピンを曲げないよう に気をつけてください。ピンを曲げるとシステム基板が破損して修復でき ない場合があります。 11 プロセッサをソケットから慎重に取り外し、ソケットに新しいプロ セッサを取り付けられるように、リリースレバーは立てたままにし ておきます。 プロセッサを取り外したら、再利用、返品、または一時的な保管の ために、静電気防止パッケージに入れます。プロセッサの底部に触 れないでください。プロセッサは側面の端以外に触れないでく ださい。 プロセッサをソケット CPU2 から取り外したままにする場合は、シ ステムの正常な冷却状態を維持するために、プロセッサのダミーと ヒートシンクのダミーを取り付ける必要があります。ダミーの取り 付け方は、プロセッサの取り付けと同様です。148 ページの「プロ セッサの取り付け」を参照してください。 メモ:シングルプロセッサ構成の場合、プロセッサはソケット CPU1
プロセッサの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 プロセッサをアップグレードする場合は、システムをアップグレー ドする前に support.dell.
8 プロセッサをソケットに取り付けます。プロセッサを水平に保ち (図 3-25 を参照)、ソケットにまっすぐに挿入します。プロセッサ は、プロセッサシールドで所定の位置に固定できるように、ピンを 合わせて軽く載せます。 図 3-25 プロセッサをソケットに対して平行に保つ 図 3-26 プロセッサをソケットキーに合わせる 3 2 4 1 5 6 7 ソケットリリースレバー 2 3 1 プロセッサシールド 4 プロセッサの切り込み(2) 5 ソケットキー(2) 6 ZIF ソケット 7 ピン 1 インジケータ(2) プロセッサ システム部品の取り付け 149
9 プロセッサとソケットが正しく揃い、装着されたことを確認します。 注意:プロセッサを強く押し込まないでください。プロセッサの位置が 合っていれば、簡単にソケットに入ります。 10 プロセッサシールドを閉じます。 11 所定の位置に収まるまで、ソケットリリースレバーを下ろします。 148 ページの「プロセッサの取り付け」を参照してください。 メモ:消費電力の大きいプロセッサの場合は、キットに交換用の ヒートシンクが入っていることがあります。新しいヒートシンクは、 外見は同じでも熱放散仕様が改善しているので、必ず使用してくだ さい。 12 糸くずの出ないきれいな布で、ヒートシンクからサーマルグリース を拭き取ります。 注意:塗布するサーマルグリースの量が多すぎると、接触するグリース の過剰からプロセッサソケットが汚れるおそれがあります。 13 プロセッサキットに含まれているグリースパケットを開き、新しい プロセッサの上部中央にサーマルグリースを均等に塗布します。 14 ヒートシンクをプロセッサの上に置きます。図 3-23 を参照してく ださい。 15 #2 プラスドライバを使用して、ヒートシンク固定ネジを締
システムバッテリー システムバッテリーの交換 警告:バッテリーの取り付け方が間違っていると、破裂するおそれがあ ります。交換用のバッテリーには、製造元が推奨する型、またはそれと同 等の製品を使用してください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 システム基板エアフローカバーを取り外します。123 ページの「シ ステム基板エアフローカバーの取り外し」を参照してください。 4 必要に応じて、ケーブルを外します。
図 3-27 システムバッテリーの交換 2 1 3 1 バッテリーコネクタのプラス (+)側 3 バッテリーコネクタのマイナス (-)側 2 システムバッテリー 5 バッテリーソケットの位置を確認します。199 ページの「ジャンパ とコネクタ」を参照してください。 注意:バッテリーの取り付け、取り外しの際には、バッテリーコネクタ が破損しないようにしっかり支えてください。 6 コネクタのプラス側をしっかり押して、バッテリーコネクタを支え ます。 7 バッテリーをコネクタのマイナス側へ押し、コネクタのマイナス側 の固定タブから外します。 8 新しいシステムバッテリーを取り付けるには、コネクタのプラス側 をしっかり押し下げてバッテリーコネクタを支えます。 9 プラス側をシステム基板上のプラスチック製コネクタの側に向けて バッテリーを持ち、固定タブの下に挿入します。 152 システム部品の取り付け
10 所定の位置にカチッと収まるまでバッテリーをコネクタに押し込み ます。 11 システム基板エアフローカバーが取り付けられていた場合は、取り 付けます。124 ページの「システム基板エアフローカバーの取り付 け」を参照してください。 12 ケーブルを外した場合は、接続します。 13 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 14 セットアップユーティリティを起動して、バッテリーが正常に動作 していることを確認します。62 ページの「セットアップユーティリ ティの起動」を参照してください。 15 セットアップユーティリティの Time(時刻)および Date(日付) フィールドで正しい時刻と日付を入力します。 16 セットアップユーティリティを終了します。 コントロールパネルアセンブリ メモ:LCD コントロールパネルアセンブリは、ディスプレイモジュールと コントロールパネル回路基板という 2 つの独立したモジュールで構成され ています。いずれのモジュールも、次の手順に従って取り外しと取り付け を行ってください。 コントロールパネルアセンブリの取り外し 注
4 コントロールパネルケーブルをコントロールパネルボードから外し ます。 • LED コントロールパネルについては、図 3-28 を参照してくださ い。 • LCD コントロールパネルについては、図 3-29 を参照してくださ い。 注意:コネクタを取り外す際にケーブルを引っ張らないでください。 ケーブルが損傷するおそれがあります。 5 ケーブルコネクタの両端の金属製タブを押します。 6 コネクタをソケットから注意深く外します。 7 LCD コントロールパネルの場合は、ディスプレイモジュールケーブ ルをコントロールパネルボードから外します。図 3-29 を参照してく ださい。 8 コントロールパネルボードをシステムシャーシに固定している 2 本 のネジを外し、ボードを取り外します。 これで LED コントロールパネルの取り外しは完了です。 9 ディスプレイモジュールを取り外すには、ナイフまたは小型のマイ ナスドライバの先端をディスプレイの前面パネルの下に挿入して左 右に動かし、パネルを外側へ持ち上げます。図 3-29 を参照してくだ さい。 10 取り付けネジに触れることができるように、パネルを上方向
図 3-28 コントロールパネル LED の取り外しと取り付け 3 2 4 1 5 6 7 1 LED ディスプレイモジュール 2 3 コントロールパネルのデータケー 4 ブル 5 取り付けネジ(2) 7 突起 6 コントロールパネルボード スロット 電源ケーブル システム部品の取り付け 155
図 3-29 コントロールパネル LCD の取り外しと取り付け 2 3 4 1 5 6 9 156 8 7 1 ディスプレイモジュールケーブル 2 コントロールパネルボード 3 コントロールパネルのデータケー 4 ブル スロット 5 取り付けネジ(2) 6 電源ケーブル 7 突起 8 前面パネルのネジ(2) 9 LCD ディスプレイモジュール システム部品の取り付け
コントロールパネルアセンブリの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 LED コントロールパネルの場合は、手順 3 に進みます。ディスプレ イモジュールをシャーシの切り欠きに挿入し、2 本のネジで固定し ます。 2 交換用のパネルをディスプレイモジュールの前面に取り付けます。 3 コントロールパネルボード内のスロットをシステムシャーシ上の突 起に合わせ、2 本のネジで固定します。図 3-29 を参照してくださ い。LED コントロールパネルの場合は、手順 4 を省略します。 4 ディスプレイモジュールケーブルをコントロールパネルボードに接 続します。 5 コントロールパネルケーブルをコントロール
SAS バックプレーン SAS バックプレーンの取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 ベゼルが取り付けてある場合は、ベゼルを取り外します。91 ページ の「前面ベゼルの取り外し」を参照してください。 2 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 3 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 注意:ドライブおよびバックプレーンの損傷を防ぐため、バックプレー ンを取り外す前にハードドライブをシステムから取り外す必要があ ります。 注意:後で同じ場所に取り付けることができるように、取り外す前に各
10 バックプレーンボード上のコンポーネントに損傷を与えないように 注意しながら、ボードを持ち上げてシステムから取り外します。 11 SAS バックプレーンを前面を下に向けて作業面に置きます。 図 3-30 SAS バックプレーンの取り外しと取り付け 1 2 3 4 5 1 SAS バックプレーン固定ラ ッチ(2) 2 SAS バックプレーン電源ケ ーブル 3 SAS A ケーブル 4 SAS バックプレーン 5 SAS B ケーブル システム部品の取り付け 159
SAS バックプレーンの取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことがで きます。製品マニュアルで許可されている範囲に限り、またはオンライン サービスもしくはテレホンサービスとサポートチームの指示によってのみ、 トラブルシューティングと簡単な修理を行うようにしてください。デルで 認められていない修理(内部作業)による損傷は、保証の対象となりませ ん。製品に付属しているマニュアルの「安全にお使いいただくために」を お読みになり、指示に従ってください。 1 SAS バックプレーンを取り付けるには、バックプレーンボード上の コンポーネントに損傷を与えないように注意しながら、バックプ レーンをゆっくりとシステムの中に入れます。 2 バックプレーンのスロットをドライブベイ背面の保持フックに合わ せ、保持フックがバックプレーンのスロットに完全に入るまで、 バックプレーンを前方に押し込みます。図 3-30 を参照してく ださい。 3 カチッと音がして 2 つの青色の固定ラッチが所定の位置に収まるま で、バックプレーンを押し下げます。 4 SAS バックプレーンに SAS データケーブルと電源ケー
配電基板 配電基板は、システムの電源ユニットファンモジュールのすぐ後ろにあり ます。配電基板エアフローカバーによって電源ユニットに空気が流れるた め、電源ユニットの冷却効果が高まります。図 3-31 を参照してくだ さい。 配電基板の取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムから電源ユニットを取り外します。106 ページの「冗長電 源ユニットの取り外し」を参照してください。 2 配電基板エアフローカバーの位置を確認し、持ち上げて取り外しま す。図 3-1 を参照してください。 3 配電ケーブルをシステム基板から外し(164 ページの「システム基板」 を参照)、ファンケーブルコネクタを外し
配電基板の取り付け 図 3-31 配電基板の取り外しと取り付け 1 2 5 4 1 162 3 ネジ(2) 2 電源ユニットコネクタ(2) 3 配電基板 4 突起(2) 5 ファンモジュールのケーブルコネ クタ(2) システム部品の取り付け
注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 新しい配電基板アセンブリのパッケージを開きます。 2 配電基板をシャーシ上の突起に合わせ、挿入して所定の位置に固定 します。図 3-31 を参照してください。 3 配電基板をシャーシに固定する 2 本のネジを取り付けます。図 3-31 を参照してください。 4 配電ケーブルをシステム基板に(164 ページの「システム基板」を 参照)、ファンケーブルコネクタを配電基板に(図 3-31 を参照)接 続します。 5 エアフローカバーの両側にあるヒンジ式の内部留め具の位置を確認 して、配電基板カバーを合わせて装着し、エアフローカバーの上に 倒します。図 3-31 を参照して
システム基板 システム基板の取り外し 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 注意:暗号化キーと共に TPM(信頼済みプログラムモジュール)を使用 している場合は、プログラムまたはシステムのセットアップ中にリカバリ キーの作成を求められることがあります。このリカバリキーは必ず作成 し、安全に保管しておいてください。このシステム基板を交換した場合 は、システムまたはプログラムの再起動時にリカバリキーを入力しない と、ハードドライブ上の暗号化されたデータにアクセスできません。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ペ
9 オプションの iDRAC6 Enterprise カードが取り付けてある場合は、 これを取り外します。128 ページの「iDRAC6 Enterprise カード(オ プション)」を参照してください。 10 オプションの iDRAC6 Express カードが取り付けてある場合は、これ を取り外します。126 ページの「iDRAC6 Express カード(オプショ ン)」を参照してください。 11 システム基板からすべてのケーブルを外します。 12 システム基板をシャーシに固定している 9 本のネジを外し、システ ム基板アセンブリをシャーシの前端方向にスライドさせます。 注意:メモリモジュール、プロセッサ、その他のコンポーネントをつか んでシステム基板を持ち上げないでください。 13 システム基板アセンブリの端を持ち、シャーシから持ち上げて取り 出します。図 3-32 を参照してください。 図 3-32 システム基板の取り外しと取り付け 1 1 ネジ(9) 2 2 システム基板アセンブリ システム部品の取り付け 165
システム基板の取り付け 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 新しいシステム基板のパッケージを開きます。 2 プロセッサシールドからラベルを剥がし、システム前面のシステム 識別パネルに貼り付けます。図 1-1 を参照してください。 3 プロセッサを新しいシステム基板に付け替えます。144 ページの 「プロセッサの取り外し」および 148 ページの「プロセッサの取り付 け」を参照してください。 4 すべてのメモリモジュールを取り付けます。143 ページの「メモリ モジュールの取り外し」および 141 ページの「メモリモジュールの 取り付け」を参照してください。 5 システム基板の端を持ち、シャーシ内に下ろ
10 ケーブルを下記の順序で接続します(システム基板上のコネクタの 位置については、図 6-1 を参照してください)。 • SATA インタフェースケーブル(該当する場合) • コントロールパネルインタフェースケーブルコネクタ • オプティカルドライブ電源ケーブルコネクタ • コントロールパネル USB インタフェースケーブルコネクタ • SAS バックプレーン電源ケーブルコネクタ • システム基板の電源ケーブルコネクタ 11 拡張カードライザーを取り付けます。121 ページの「拡張カードラ イザーの取り付け」を参照してください。 12 必要に応じて、拡張カードを取り付けます。114 ページの「拡張 カードの取り付け」を参照してください。 13 内蔵ストレージコントローラカードを取り外した場合は、取り付け ます。117 ページの「内蔵ストレージコントローラカードの取り付 け」を参照してください。 SAS ケーブルをコントローラに接続したら、ケーブルを必ずライ ザー 1 の端にあるガイドの下に配線してください。 14 RAID バッテリーケーブルを PERC コントローラカードから外した
システム部品の取り付け
システムのトラブルシ ューティング 作業にあたっての注意 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 システム起動エラーのトラブルシ ューティング 起動中、ビデオイメージングまたは LCD メッセージの前にシステムが停 止する場合(特に、OS のインストールやシステムのハードウェアの再構 成を行った後である場合)、次の条件が該当しないかチェックしてくだ さい。 • OS を UEFI ブートマネージャからインストールした後にシステムを BIOS 起動モードで起動すると、システムがハングします。この逆に ついても同じです。OS をインストールしたのと同じ起動モードで起 動する必要があります。61 ページの「セッ
外部接続のトラブルシューティング 外付けデバイスのトラブルシューティングを行う前に、すべての外部ケー ブルがシステムの外部コネクタにしっかりと接続されていることを確認し ます。システムの前面および背面パネルのコネクタについては、図 1-1 お よび 図 1-4 を参照してください。 ビデオサブシステムのトラブルシ ューティング 1 モニターとシステム、およびモニターと電源の接続を確認します。 2 システムとモニターの間のビデオインタフェースのケーブル接続を 確認します。 3 システムに 2 台のモニターが接続されている場合は、1 台を取り外 します。システムには、前面と背面のどちらかのビデオコネクタに モニターを 1 台のみ接続できます。 4 問題が解決しない場合は、207 ページの「困ったときは」を参照し てください。 170 システムのトラブルシ ューティング
USB デバイスのトラブルシューティング 1 USB キーボードおよび / またはマウスのトラブルシューティングは、 次の手順で行います。その他の USB デバイスの場合は、手順 2 に進 みます。 a システムからキーボードとマウスのケーブルを短時間外し、再接 続します。 b キーボード / マウスをシステムの反対側の USB ポートに接続し ます。 これで問題が解決した場合は、システムを再起動し、セットアッ プユーティリティを起動して、機能していない USB ポートが有 効になっているかどうかを確認します。 c キーボード / マウスを動作確認済みの別のキーボード / マウスと 交換します。 これで問題が解決した場合は、障害のあるキーボード / マウスを 交換します。 問題が解決しない場合は、次の手順に進んで、システムに取り付 けられているその他の USB デバイスのトラブルシューティング を開始します。 2 取り付けられているすべての USB デバイスの電源を切り、システム から外します。 3 システムを再起動し、キーボードが機能している場合は、セット アップユーティリティを起動します。すべ
シリアル I/O デバイスのトラブルシ ューティング 1 システムおよびシリアルポートに接続された周辺機器すべての電源 を切ります。 2 シリアルインタフェースケーブルを正常な別のケーブルと取り替え、 システムとシリアルデバイスの電源を入れます。 これで問題が解決した場合は、インタフェースケーブルを交換し ます。 3 システムとシリアルデバイスの電源を切り、デバイスを同じタイプ のデバイスと取り替えます。 4 システムとシリアルデバイスの電源を入れます。 これで問題が解決した場合は、シリアルデバイスを交換します。 問題が解決しない場合は、207 ページの「困ったときは」を参照し てください。 NIC のトラブルシューティング 1 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「Dell Diagnostics の使い方」を参照してください。 2 システムを再起動し、NIC コントローラに関するシステムメッセー ジがないかチェックします。 3 NIC コネクタの該当するインジケータを確認します。20 ページの 「NIC インジケータコード」を参照してください。 • リ
4 適切なドライバがインストールされ、プロトコルが組み込まれてい ることを確認します。NIC のマニュアルを参照してください。 5 セットアップユーティリティを起動し、NIC ポートが有効になって いることを確認します。70 ページの「Integrated Devices(内蔵デ バイス)画面」を参照してください。 6 ネットワーク上の NIC、ハブ、およびスイッチが、すべて同じデー タ転送速度に設定されていることを確認します。各ネットワークデ バイスのマニュアルを参照してください。 7 すべてのネットワークケーブルのタイプが適切で、最大長を超えて いないことを確認します。 すべてのトラブルシューティングが失敗した場合は、207 ページの 「困ったときは」を参照してください。 システムが濡れた場合のトラブルシ ューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていな
3 コンポーネントをシステムから取り外します。89 ページの「システ ム部品の取り付け」を参照してください。 • システム基板エアフローカバー • 配電基板エアフローカバー • ハードドライブ • VFlash SD カード • USB メモリキー • NIC ハードウェアキー • 拡張カード • 内蔵ストレージカード • iDRAC6 Express カード • iDRAC6 Enterprise カード • 電源ユニット • ファン • プロセッサとヒートシンク • メモリモジュール 4 システムを完全に乾燥させます(少なくとも 24 時間)。 5 手順 3 で取り外したコンポーネントを取り付けます。 6 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 7 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 システムが正常に起動しない場合は、207 ページの「困ったときは」 を参照してください。 8 システムが正常に起動する場合は、システムをシャットダウンして、
システムが損傷した場合のトラブルシ ューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 3 以下のコンポーネントが正しく取り付けられていることを確認 します。 • 拡張カード • 電源ユニット • ファン • プロセッサとヒートシンク • メモリモジュール • ハードドライブキャリア • システム基板エアフローカバー • 配電基板エアフローカバー 4 すべてのケーブルが正しく接続され
システムバッテリーのトラブルシ ューティング メモ:長い期間(数週間から数か月)システムの電源が切られていると、 NVRAM からシステム設定情報が失われる場合があります。これはバッテ リーの不良が原因です。 1 セットアップユーティリティで時刻と日付を再入力します。62 ペー ジの「セットアップユーティリティの起動」を参照してください。 2 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムを 1 時間以上コンセントから外しておきます。 3 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 4 セットアップユーティリティを起動します。 セットアップユーティリティの日付と時刻が正しくない場合は、 バッテリーを交換します。151 ページの「システムバッテリーの交 換」を参照してください。 メモ:一部のソフトウェアには、システムの時刻を進めたり遅らせたり するものがあります。セットアップユーティリティ内に保持されている時 刻以外はシステムが正常に動作している場合、問題の原因はバッテリーの 不良ではなく、ソフトウェアにあると考えられます。 バッテリーを
電源ユニットのトラブルシューティング 注意:システムが動作するためには、電源ユニットを必ず 1 台は取り付 けておく必要があります。電源ユニットが 1 台しか取り付けられていない システムを長時間使用すると、システムがオーバーヒートするおそれがあ ります。 1 電源ユニットの障害インジケータで故障した電源ユニットを特定し ます。21 ページの「電源インジケータコード」を参照してく ださい。 2 電源ユニットをいったん取り外して取り付けなおします。106 ペー ジの「電源ユニット」を参照してください。 メモ:電源ユニットを取り付けたら、システムが電源ユニットを認 識して動作状態を確認するまで数秒待ちます。電源インジケータが 緑色に点灯すれば、電源ユニットは正常に機能しています。 問題が解決しない場合は、障害のある電源ユニットを交換します。 3 問題が解決しない場合は、207 ページの「困ったときは」を参照し てください。 システム冷却問題のトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスも
ファンのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 注意:冷却ファンはホットスワップ対応です。システムの電源が入って いる間は、適切な冷却効果を維持するため、ファンの交換は 1 台ずつ行っ てください。 2 LCD パネルまたは Diagnostics(診断)ソフトウェアが障害を指摘し ているファンの位置を確認します。 3 システムおよび接続されているすべての周辺機器の電源を切ります。 4 ファンを取り外して装着しなおします。133 ページの「冷却ファン の取り外し」参照してください。 5 シス
システムメモリのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 メモ:メモリ構成が無効な場合は、ビデオ出力がなく、起動時にシステ ムが停止することがあります。138 ページの「メモリモジュール取り付け の一般的ガイドライン」を参照し、メモリ構成が該当するすべてのガイド ラインに従っていることを確認します。 1 システムが機能している場合は、適切なオンライン Diagnostics(診 断)テストを実行します。193 ページの「システム診断プログラム の実行」を参照してください。 Diagnostics(診断)で障害が示された場合は、Diagnostics(診断) プログラムによって示される対応
7 冷却用エアフローカバーが取り付けられている場合は、取り外しま す。123 ページの「システム基板エアフローカバーの取り外し」を 参照してください。 8 メモリチャネルをチェックし、正しく装着されていることを確認し ます。138 ページの「メモリモジュール取り付けの一般的ガイドラ イン」を参照してください。 9 ソケットに装着されている各メモリモジュールを抜き差しします。 141 ページの「メモリモジュールの取り付け」を参照してください。 10 冷却用エアフローカバーが取り付けられていた場合は、取り付けま す。124 ページの「システム基板エアフローカバーの取り付け」を 参照してください。 11 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 12 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 13 セットアップユーティリティを起動して、システムメモリの設定を 確認します。66 ページの「Memory Settings(メモリ設定)画面」 を参照してください。 問題が解決しない場合は、次の手順に進みます。 14 D
19 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 20 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 21 システムの起動中に表示されるエラーメッセージ、およびシステム 前面の Diagnostics(診断)インジケータを観察します。 22 メモリの問題が引き続き示される場合は、取り付けられている各メ モリモジュールについて 手順 14 ~ 手順 21 を繰り返します。 すべてのメモリモジュールをチェックしても問題が解決しない場合 は、207 ページの「困ったときは」を参照してください。 内蔵 USB キーのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお
9 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 10 システムおよび接続されている周辺機器の電源を入れ、USB キーが 機能しているかどうかチェックします。 問題が解決しない場合は、207 ページの「困ったときは」 を参照して ください。 SD カードのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 セットアップユーティリティを起動し、内蔵 SD カードポートが有効 になっていることを確認します。70 ページの「Integrated Devices (内蔵デバイス)画面」を参照してください。 2 システムおよび接続されているすべての周辺機器
5 SD カード 1 に障害が発生した場合は、カードを SD カードスロット 1 から取り外します。132 ページの「VFlash メディアカードの取り 外し」を参照してください。SD カード 2 に障害が発生した場合は、 SD カードスロット 2 に新しい SD カードを取り付けて 手順 8 に進み ます。 6 SD カードスロット 2 に取り付けられているカードを取り外し、SD カードスロット 1 に挿入します。132 ページの「VFlash メディア カードの取り外し」および 132 ページの「VFlash メディアカードの 取り付け」を参照してください。 7 新しい SD カードを SD カードスロット 2 に挿入します。 8 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 9 システムおよび接続されている周辺機器の電源を入れ、SD カードが 機能しているかどうかチェックします。 10 動作確認済みの別の SD カードを挿入します。 11 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 12 システムおよび接続され
3 セットアップユーティリティを起動し、内蔵 SATA コントローラと ドライブの SATA ポートが有効になっていることを確認します。 61 ページの「セットアップユーティリティと UEFI ブートマネー ジャの使い方」を参照してください。 4 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「システム診断プログラムの実行」を参照してくださ い。 5 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 6 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 7 インタフェースケーブルがオプティカルドライブおよびコントロー ラにしっかり接続されていることを確認します。135 ページの 「RAID バッテリー(オプション)」を参照してください。 8 電源ケーブルがドライブに正しく接続されていることを確認します。 9 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 10 電源ケーブルをコンセントに差し込んで、システムと周辺機器の電 源を入れます。 問
5 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「システム診断プログラムの実行」を参照してく ださい。 6 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 7 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 8 拡張カードスロットのコントローラカードを抜き差しします。 9 テープドライブのインタフェースケーブルが、テープドライブおよ びコントローラカード(SAS または SCSI)のコネクタまたはシステ ム基板の SATA コネクタにしっ
ハードドライブのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 注意:このトラブルシューティング手順を実行すると、ハードドライブ に保存されたデータが損傷するおそれがあります。以下の手順を実行する 前に、ハードドライブ上のすべてのファイルをバックアップしてく ださい。 1 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「Dell Diagnostics の使い方」を参照してください。 Diagnostics(診断)テストの結果に応じて、必要に応じて以下の手 順に進みます。 2 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し
4 お使いのコントローラカードに必要なデバイスドライバがインス トールされ、正しく設定されていることを確認します。詳細につい ては、OS のマニュアルを参照してください。 5 システムを再起動し、セットアップユーティリティを起動して、コ ントローラが有効になっていてドライブが表示されていることを確 認します。61 ページの「セットアップユーティリティと UEFI ブー トマネージャの使い方」を参照してください。 問題が解決しない場合は、207 ページの「困ったときは」を参照し てください。 ストレージコントローラのトラブルシ ューティング メモ:SAS または PERC コントローラのトラブルシューティングを行う際 には、OS のマニュアルとコントローラのマニュアルも参照してください。 1 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「Dell Diagnostics の使い方」を参照してください。 2 セットアップユーティリティを起動し、SAS または PERC コント ローラが有効になっていることを確認します。61 ページの「セット アップユーティリティと UE
5 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し」を参照してください。 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 6 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 7 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 8 コントローラカードがシステム基板のコネクタにしっかりと装着さ れていることを確認します。132 ページの「VFlash メディア(オプ ション)」を参照してください。 9 バッテリーバックアップされたキャッシュ付きの PERC コントロー ラを使用している場合は、RAI
拡張カードのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 メモ:拡張カードのトラブルシューティングを行う際には、OS と拡張 カードのマニュアルを参照してください。 1 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「Dell Diagnostics の使い方」を参照してください。 2 必要であれば、前面ベゼルを取り外します。91 ページの「前面ベゼ ルの取り外し」を参照してください。 3 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 4 システムカバーを開きます。92 ページの「システムカバーの取り外
12 電源ケーブルをコンセントに差し込んで、システムと周辺機器の電 源を入れます。 13 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「システム診断プログラムの実行」を参照してく ださい。 テストが失敗した場合は、207 ページの「困ったときは」を参照し てください。 プロセッサのトラブルシューティング 注意:修理作業の多くは、認定されたサービス技術者のみが行うことが できます。製品マニュアルで許可されている範囲に限り、またはオンライ ンサービスもしくはテレホンサービスとサポートチームの指示によっての み、トラブルシューティングと簡単な修理を行うようにしてください。デ ルで認められていない修理(内部作業)による損傷は、保証の対象となり ません。製品に付属しているマニュアルの「安全にお使いいただくため に」をお読みになり、指示に従ってください。 1 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「Dell Diagnostics の使い方」を参照してください。 2 システムおよび接続されているすべての周辺機器の電源を切り、シ ス
8 適切なオンライン Diagnostics(診断)テストを実行します。 193 ページの「システム診断プログラムの実行」を参照してくだ さい。 システムに搭載しているプロセッサが 1 個だけで、問題が解決しな い場合は、207 ページの「困ったときは」を参照してください。 9 複数のプロセッサを搭載したシステムの場合は、システムおよび接 続されているすべての周辺機器の電源を切り、システムをコンセン トから外します。 10 システムカバーを開きます。92 ページの「システムカバーの取り外 し」を参照してください。 11 システム基板エアフローカバーを取り外します。123 ページの「シ ステム基板エアフローカバーの取り外し」を参照してください。 12 プロセッサ 2 を取り外します。144 ページの「プロセッサの取り外 し」を参照してください。 13 システムカバーを閉じます。93 ページの「システムカバーの取り付 け」を参照してください。 14 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 15 適切なオンライン Diagnostics(診断)テストを実行しま
システムのトラブルシ ューティング
システム診断プログラムの実行 システムに問題が発生した場合、テクニカルサポートに電話される前に診 断プログラムを実行してください。診断プログラムを使うと、特別な装置 を使用せずにシステムのハードウェアをテストでき、データが失われる心 配もありません。ご自身で問題を解決できない場合でも、サービスおよび サポート担当者が診断プログラムのテスト結果を使って問題解決の手助け を行うことができます。 Dell Diagnostics の使い方 システムの問題を分析するには、オンライン Diagnostics(診断)を最初 に使用します。オンライン Diagnostics(診断)は、診断プログラムまた はテストモジュールの一式であり、ハードドライブ、物理メモリ、通信 ポート、プリンタポート、NIC、CMOS など、シャーシやストレージコン ポーネントを対象とする診断テストを実行します。オンライン Diagnostics(診断)を使用して問題を識別できない場合は、内蔵された システム診断プログラムを使用します。 サポートされている Microsoft Windows OS および Linux OS を実行して いるシステ
内蔵されたシステム診断プログラムの機能 システム診断プログラムは、特定のデバイスグループや各デバイス用の一 連のテストメニューとオプションで構成されています。システム診断プロ グラムのメニューとオプションを使って、以下のことが行えます。 • テストを個別または全体的に実行 • テストの順序を制御 • テストの繰り返し • テスト結果の表示、印刷、または保存 • エラーが検知された場合にテストを一時的に中断、またはユーザー が指定する最大エラー数に達したときにテストを終了 • 各テストとそのパラメータを簡潔に説明するヘルプメッセージを表 示 • テストが問題なく終了したかどうかを知らせるステータスメッセー ジを表示 • テスト中に発生した問題を通知するエラーメッセージを表示 内蔵されたシステム診断プログラムの実行が 必要な場合 システム内の主要コンポーネントまたはデバイスが正しく動作していない 場合、コンポーネントの障害が表示されることがあります。マイクロプロ セッサとシステムの I/O デバイスが動作していれば、問題の識別にシステ ム診断プログラムを使用することができます。
内蔵されたシステム診断プログラムの実行 内蔵されたシステム診断プログラムは、Life Cycle Controller 画面から実 行します。 注意:内蔵されたシステム診断プログラムは、お使いのシステムをテス トする場合にのみ使用してください。このプログラムを他のシステムで使 用すると、無効な結果やエラーメッセージが発生する場合があります。 1 システム起動中に を押します。 2 左ペインで Diagnostics(診断)をクリックし、右ペインで Launch Diagnostics(Diagnostics(診断)の起動)をクリックし ます。 Diagnostics(診断)メニューは、すべてまたは特定の診断テストの実行 や、診断プログラムの終了に使用します。 システム診断プログラムのテストオプション Main Menu(メインメニュー)ウィンドウでテストオプションをクリッ クします。 テストオプション 機能 Express Test(エクスプ システムのクイックチェックを実行します。このオ レステスト) プションでは、ユーザーの応答を必要としないデバ イステストを実行します。 Extende
カスタムテストオプションの使い方 Main Menu(メインメニュー)ウィンドウで Custom Test(カスタム テスト)を選択すると、Customize(カスタマイズ)ウィンドウでテス トするデバイスを選択できます。希望するテストオプションを選択して、 テスト結果を表示します。 テストするデバイスの選択 Customize(カスタマイズ)ウィンドウの左側にはテスト可能なデバイ スのリストが表示されます。デバイスまたはモジュールの横にある(+) をクリックすると、各コンポーネントが表示されます。各コンポーネント の横にある(+)をクリックすると、利用可能なテストが表示されます。 コンポーネントではなくデバイスをクリックすると、テストするデバイス のすべてのコンポーネントが選択できます。 メモ:テストするすべてのデバイスとコンポーネントを選択したら、All Devices(すべてのデバイス)をハイライト表示し、Run Tests(テストの 実行)をクリックします。 診断オプションの選択 Diagnostics Options(診断オプション)領域で、デバイスに対して実 行するテストを選択します。 •
情報および結果の表示 Customize(カスタマイズ)ウィンドウの以下のタブを使って、テスト とテスト結果についての情報を表示することができます。 • Results(結果)— 実行されたテストとその結果が表示されます。 • Errors(エラー)— テスト中に発生したエラーが表示されます。 • Help(ヘルプ)— 現在選択されているデバイス、コンポーネント、 またはテストに関する情報が表示されます。 • Configuration(設定)— 現在選択されているデバイスの基本設定 に関する情報が表示されます。 • Parameters(パラメータ)— そのテストで設定可能なパラメータ が表示されます。 システム診断プログラムの実行 197
システム診断プログラムの実行
ジャンパとコネクタ 本項では、システムジャンパについて説明します。また、ジャンパとス イッチに関する基本的な情報を提供するとともに、システム内のさまざま な基板上のコネクタについても説明します。 システム基板のジャンパ システム基板上のジャンパの位置を 図 6-1 に示します。また、 表 6-1 に はジャンパ設定のリストを示します。 表 6-1 システム基板のジャンパ設定 ジャンパ 設定 説明 PWRD_EN パスワード機能は有効です。 (ピン 2-4) (デフォルト) パスワード機能が無効になり、iDRAC6 のローカルアクセスは次の AC 電源サイ クルでロック解除されます。(ピン 4-6) NVRAM_CLR 構成設定がシステム起動時に保持され (デフォルト) ます。(ピン 3-5) 構成設定は、次のシステム起動時にクリ アされます。(ピン 1-3) ジャンパとコネクタ 199
システム基板のコネクタ システム基板のコネクタの位置と説明については、図 6-1 および 表 6-2 を参照してください。 図 6-1 システム基板のコネクタ 1 3 2 20 19 18 17 4 16 5 15 14 13 12 11 200 10 ジャンパとコネクタ 9 8 7 6
表 6-2 システム基板のコネクタ 項目 コネクタ 説明 1 CPU2 プロセッサ 2 2 iDRAC6 Enterprise iDRAC6 Enterprise カードコネクタ 3 PWRD_EN パスワード有効ジャンパ NVRAM_CLR NVRAM クリアジャンパ B1 メモリモジュールスロット B1(白色のリリース レバー) B3 メモリモジュールスロット B3 B2 メモリモジュールスロット B2(白色のリリース レバー) B4 メモリモジュールスロット B4 5 CPU1 プロセッサ 1 6 FAN1 システムファン 1 コネクタ 7 FAN2 システムファン 2 コネクタ 8 A4 メモリモジュールスロット A4 A2 メモリモジュールスロット A2(白色のリリース レバー) A3 メモリモジュールスロット A3 A1 メモリモジュールスロット A1(白色のリリース レバー) 9 FAN3 システムファン 3 コネクタ 10 FAN4 システムファン 4 コネクタ 11 12V 8 ピン電源コネクタ
表 6-2 システム基板のコネクタ (続き) SATA_A SATA コネクタ A SATA_B SATA コネクタ B SATA_C SATA コネクタ C SATA_D SATA コネクタ D SATA_E SATA コネクタ E 18 RISER 拡張カードライザーコネクタ 19 RISER 拡張カードライザーコネクタ 20 iDRAC6 Express iDRAC6 Express カードコネクタ 17 メモ:この表で使用されている略語や頭字語の正式名については、 support.dell.
拡張カードライザーボードのコンポーネント および PCIe バス 図 6-3 PCIe 拡張カードライザーのコンポーネント 4 3 2 1 1 データケーブルコネクタ 2 SAS 電源ケーブルコネクタ 3 スロット 2 — 内蔵ストレージ コントローラカードコネクタ 4 スロット 1 — PCIe - x16 リンク 拡張スロット ジャンパとコネクタ 203
配電基板コネクタ 図 6-4 配電基板コネクタ 1 3 2 204 1 電源ユニットコネクタ(2) 3 ファンモジュール電源 ケーブルコネクタ(2) ジャンパとコネクタ 2 システム基板電源ケーブル コネクタ(3)
パスワードを忘れたとき システムのソフトウェアセキュリティ機能として、システムパスワードと セットアップパスワードを設定することができます。これらのパスワード については、61 ページの「セットアップユーティリティと UEFI ブートマ ネージャの使い方」で詳しく説明されています。パスワードジャンパを 使って、これらのパスワード機能を有効または無効に設定できるので、現 在どのようなパスワードが使用されていてもクリアすることができます。 注意:システムに付属のマニュアルで、「安全にお使いいただくために」 の「静電気障害への対処」を参照してください。 1 システムおよび接続されているすべての周辺機器の電源を切り、シ ステムをコンセントから外します。 2 システムカバーを開きます。92 ページの「システムカバーの取り外 しと取り付け」を参照してください。 3 パスワードジャンパを「無効」の位置に移動して、パスワードをク リアします。表 6-1 を参照してください。システム基板上のパス ワードジャンパの位置については、図 6-1 を参照してください。 4 システムカバーを閉じます。 5 システムおよびシステムに接続さ
8 パスワードジャンパを有効の位置に戻して、パスワード機能を回復 します。表 6-1 を参照してください。 9 システムカバーを閉じます。 10 システムおよびシステムに接続されているすべての周辺機器をコン セントに接続し、電源を入れます。 11 新しいシステムパスワードとセットアップパスワードの両方または そのどちらか一方を設定します。 セットアップユーティリティを使用して新しいパスワードを設定す るには、81 ページの「システムパスワードとセットアップ パスワー ドの機能」を参照してください。 206 ジャンパとコネクタ
困ったときは デルへのお問い合わせ 米国にお住まいの方は、800-WWW-DELL(800-999-3355)までお電話く ださい。 メモ:お使いのコンピュータがインターネットに接続されていない場合 は、購入時の納品書、出荷伝票、請求書、またはデルの製品カタログで連 絡先をご確認ください。 デルでは、オンラインまたは電話によるサポートとサービスのオプション を複数提供しています。サポートやサービスの提供状況は国や製品ごとに 異なり、国 / 地域によってはご利用いただけないサービスもございます。 デルのセールス、テクニカルサポート、またはカスタマーサービスへは、 次の手順でお問い合わせいただけます。 1 support.dell.
困ったときは
索引 B I BMC 設定 , 86 iDRAC カード システムポート , 18 取り付け , 128 C iDRAC6 カード 取り付け , 126 CD ドライブ トラブルシューティング , 183 iDRAC6 設定ユーテ ィリティ , 87 CD/DVD ドライブ 「オプティカルドライブ」 を参照 L D LCD パネル メニュー , 15 機能 , 13 Diagnostics(診断) Advanced Testing オプシ ョン , 196 オンライン診断プログラムの使 い方 , 193 テストオプション , 195 使用する状況 , 194 内蔵されたシステム診断プログ ラム , 193 DIMM 「メモリモジュール(DIMM)」 を参照 N NIC インジケータ , 20 トラブルシューティング , 172 背面パネルコネクタ , 18 P POST システムの機能へのア クセス , 9 索引 209
S SAS RAID コントローラドー ターカード トラブルシューティング , 187 Unified Server Configurator, 86 USB 前面パネルコネクタ , 10 SAS コントローラカード 取り外し , 116 取り付け , 117 USB キー トラブルシューテ ィング , 181-182 SAS コントローラドータ ーカード トラブルシューティング , 187 USB デバイス 背面パネルコネクタ , 18 SAS ハードドライブ 「ハード ドライブ」を参照 SAS バックプレーンボード 取り外し , 158 取り付け , 160 SATA ハードドライブ 「ハードドライブ」を参照 SD カード トラブルシューティ ング , 181-182 Z アップグレード プロセッサ , 144 安全について , 169 インジケータ NIC, 20 前面パネル , 10 電源 , 10, 21 背面パネル , 18 エラーメッセージ , 62 T TPM セキュリティ , 75 オプティカルドライブ 取り付け , 102 オンラインの Dell Diagnostics
カバー 閉じる , 93 開く , 92 システム カバーの取り付け , 93 カバーの取り外し , 92 ガイドライン 拡張カードの取り付け , 111 外付けデバイスの接続 , 20 メモリの取り付け , 138 システムが損傷した場合 トラブルシューティング , 175 起動時 システムの機能へのア クセス , 9 システム機能 アクセス , 9 キーボード トラブルシューティング , 171 組み込みシステム管理 , 86 警告メッセージ , 59 システムが濡れた場合 トラブルシューティング , 173 システム基板 コネクタ , 200, 203 ジャンパ , 199 取り付け , 166 取り外し , 164 ケーブル接続 オプティカルドライブ , 102 システムの保護 , 75, 83 交換 システムバッテリー , 151 システムメッセージ , 42 コネクタ USB, 10 システム基板 , 200, 203 ビデオ , 10 コントロールパネルアセンブリ LCD パネルの機能 , 13 機能 , 10 取り付け , 157 取り外し , 153 サービス技術者
セットアップユーティリ ティ ( 続き ) 電源管理のオプション , 74 内蔵デバイスのオプション , 70 入力するキーストローク , 62 プロセッサの設定 , 66 メモリの設定 , 66 セットアップユーティリティの 画面 メイン , 63 前面パネルの機能 , 10 ダミー 電源ユニット , 108 ハードドライブ , 94 テープドライブ トラブルシューティング , 184 デル お問い合わせ , 207 デルへのお問い合わせ , 207 電源インジケータ , 10, 21 電源ユニット インジケータ , 21 取り付け , 107, 111 取り外し , 106, 108 電源ユニットダミー , 108 電話番号 , 207 トラブルシューティング CD ドライブ , 183 NIC, 172 SAS RAID コントローラドー ターカード , 187 SD カード , 181-182 拡張カード , 189 212 索引 トラブルシューティン グ ( 続き ) 外部接続 , 170 キーボード , 171 システムが損傷した場合 , 175 システムが濡れた場合 , 173 システム冷却
取り外し SAS コントローラ , 116 SAS バックプレーン ボード , 158 拡張カード , 113 カバー , 92 コントロールパネルアセ ンブリ , 153 システム基板 , 164 電源ユニット , 106, 108 電源ユニットダミー , 108 ハードドライブ(ケーブ ル接続式), 99 ハードドライブのダミー , 94 ハードドライブ(ホットプラグ 対応), 95 プロセッサ , 144 ベゼル , 91 メモリモジュール , 143 冷却用エアフローカバー , 123, 125 ドライブダミー 取り付け , 95 取り外し , 94 内蔵されたシステム診断プログ ラムの機能 使い方 , 193 背面パネルの機能 , 18 ハードドライブ トラブルシューティング , 186 ハードドライブ(ケーブル 接続式) 取り付け , 100 取り外し , 99 ハードドライブ(ホットプラグ 対応) 取り付け , 97 取り外し , 95 バッテリー RAID カードバッテリーのトラ ブルシューティング , 187 トラブルシューティング , 176 バッテリー(システム) 交換 , 151 パ
メモリ トラブルシューティング , 179 リモートアクセスコントローラ 「iDRAC」を参照 メモリモジュール(DIMM) RDIMM 構成 , 140 UDIMM 構成 , 112 構成 , 138 取り付け , 141 取り外し , 143 冷却ファン トラブルシューティング , 178 取り付け , 134 214 索引 冷却用エアフローカバー 取り付け , 124, 126 取り外し , 123, 125