Dell™ PowerEdge™ R715 HardwareBenutzerhandbuch Genormtes Modell: E05S Genormter Typ: E05S001
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie den Computer besser einsetzen können. VORSICHTSHINWEIS: Ein VORSICHTSHINWEIS macht aufmerksam auf mögliche Beschädigung der Hardware oder Verlust von Daten bei Nichtbefolgung von Anweisungen. WARNUNG: Durch eine WARNUNG werden Sie auf Gefahrenquellen hingewiesen, die materielle Schäden, Verletzungen oder sogar den Tod von Personen zur Folge haben können.
Inhalt 1 Wissenswertes zum System . . . . . . . . . . Zugreifen auf Funktionen beim Systemstart. . . . . . . Merkmale und Anzeigen auf der Vorderseite . 11 . . . . . 12 . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . . . . . . . . 16 Merkmale des LCD-Bedienfelds Home-Bildschirm . Menü Setup . 11 Menü View (Anzeige) . . . . . . . . . . . . . . . . 17 Festplattenanzeigemuster . . . . . . . . . . . . . . . .
Alarmmeldungen . . . . . . . . . . . . . . . . . . . . . Weitere nützliche Informationen 2 . . . . . . . . . . . . Verwenden des System-Setup-Programms und des UEFI-Boot-Managers . Auswahl des Systemstartmodus . 63 . . . . . . . . . . . . 63 Reaktion auf Fehlermeldungen . . . . . . . . . 64 . . . . . . . . . . 64 Verwenden der Steuertasten des System-Setup-Programms . . . . . . . . . . . . . Optionen des System-Setup-Programms 66 . . . . . . . . . . . . . . . . . . 66 . . . . . . . . . .
Aufrufen des UEFI-Boot-Managers . . . . . . . . . . . Verwenden der Navigationstasten des UEFI-Boot-Managers . . . . . . . . . . . . . . . . 78 Bildschirm „UEFI Boot Manager“ (UEFI-Boot-Manager)) . . . . . . . . . . . . . . . 79 Bildschirm „UEFI Boot Settings“ (UEFI-Starteinstellungen) . . . . . . . . . . . . . . 79 . . . . . . . . . . . 80 Bildschirm „System Utilities“ (Systemdienstprogramme) . . System- und Setup-Kennwortfunktionen . . . . . . . . 80 Verwenden des Systemkennworts . . . .
Entfernen eines Laufwerkträgers . . . . . . . . . . Installieren eines Laufwerkträgers . Entfernen einer Festplatte aus einem Laufwerkträger . . . . . . . . . . . . 95 . . . . . . . . . . . 96 Installieren einer Festplatte im Laufwerkträger Optisches Laufwerk . . 97 . . . . . . . . . . . . . . . . . . . 97 Entfernen eines optischen Laufwerks . . . . . . . Installation eines optischen Laufwerks Netzteile 97 99 100 Entfernen eines Netzteils . . . . . . . . . . . . .
Erweiterungskarten und Erweiterungskarten-Riser . . . . . . . . . . . . . . . . Richtlinien zur Installation von Erweiterungskarten . . . . . . . . . . . . . . Installieren einer Erweiterungskarte . Entfernen von Erweiterungskarten . 122 . . . . . . . . 124 . . . . Installieren von Erweiterungskarten-Riser 1 . Entfernen des Erweiterungskarten-Risers 2 125 . . . 127 . . . . 127 Installieren von Erweiterungskarten-Riser 2 . . . . 129 . . . . . . . . . . 129 . . . . . . . . . . . . .
Prozessoren . . . . . . . . . . . . . . . . . . . . . . Entfernen eines Prozessors. . . . . . . . . . . . Installieren eines Prozessors . Systembatterie 145 . . . . . . . . . . . . . . . . . . . . . 147 SAS-Rückwandplatine . . . . . . . . . 147 . . . . . . . . . . . . . . . . 150 Entfernen der SAS-Rückwandplatine . . . . . . Installieren der SAS-Rückwandplatine . Stromverteilungsplatine . . . . . . 152 . . . . . . . . . . . . . . . 153 . . . . .
Fehlerbehebung bei einem seriellen E/A-Gerät Fehlerbehebung bei einem NIC . . . . 170 . . . . . . . . . . . . . 170 Fehlerbehebung bei Feuchtigkeit im System Fehlerbehebung bei einem beschädigten System . . . 173 . . . . . . . . 174 . . . . . . . . . . . . . 175 Fehlerbehebung bei der Systembatterie Fehlerbehebung bei Netzteilen Fehlerbehebung bei der Systemkühlung Fehlerbehebung bei einem Lüfter Fehlerbehebung beim Systemspeicher . . . . . . . . 175 . . . . . . . . . 176 . . . . . . . .
Testoptionen der Systemdiagnose . . . . . . . . . . . . . 191 . . . . . . 191 . . . . . . . 192 Verwenden der benutzerdefinierten Testoptionen Auswählen von Geräten für den Test . Auswählen von Diagnoseoptionen . Anzeigen der Informationen und Ergebnisse . 6 . . 192 . . . . 193 . . . . . . . . . . . . 193 Jumper, Schalter und Anschlüsse . Jumper auf der Systemplatine . Anschlüsse auf der Systemplatine. . . . . . . . . . . . . . . . . . 197 Anschlüsse der Stromverteilungsplatine . . . .
Wissenswertes zum System Zugreifen auf Funktionen beim Systemstart Mit den folgenden Tastenkombinationen erhalten Sie beim Startvorgang Zugriff auf Systemfunktionen. Tastenkombination Beschreibung Aufruf des System-Setup-Programms. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 63. Aufruf von System Services, von wo aus der Lifecycle-Controller geöffnet wird.
Merkmale und Anzeigen auf der Vorderseite Abbildung 1-1. Merkmale und Anzeigen auf der Vorderseite 1 2 3 4 5 6 Element Anzeige, Taste oder Anschluss 1 7 8 Symbol Betriebsanzeige, Netzschalter 9 10 Beschreibung Die Betriebsanzeige leuchtet, wenn das System eingeschaltet ist. Über den Netzschalter wird die Gleichstromversorgung des Systems gesteuert. Bei installierter Frontverkleidung ist der Netzschalter nicht zugänglich.
Element Anzeige, Taste oder Anschluss 2 NMI-Taste Symbol Beschreibung Dient dazu, Softwareprobleme und Fehler von Gerätetreibern zu beheben, wenn bestimmte Betriebssysteme verwendet werden. Sie können diese Taste mit einer aufgebogenen Büroklammer betätigen. Diese Taste sollte nur auf Anweisung eines zugelassenen Support-Mitarbeiters oder entsprechend der Dokumentation des Betriebssystems verwendet werden. 3 USB-Anschlüsse (2) Zum Anschließen von USB-Geräten am System. Die Schnittstellen sind USB-2.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 8 Systemidentifikationstaste Die Identifikationstasten auf der Vorderund Rückseite dienen dazu, ein bestimmtes System innerhalb eines Racks zu lokalisieren. Wird eine dieser Tasten gedrückt, blinken das LCDDisplay auf der Vorderseite und die Systemstatusanzeige auf der Rückseite, bis eine der Tasten erneut gedrückt wird. 9 Optisches Laufwerk (optional) Ein optionales SATA-DVD-ROM- oder DVD-RW-Laufwerk in Flachbauweise.
Abbildung 1-2. Merkmale des LCD-Bedienfelds 1 2 3 4 Element Tasten Beschreibung 1 Links Bewegt den Cursor schrittweise zurück. 2 Auswählen Wählt den vom Cursor markierten Menüeintrag aus. 3 Rechts Bewegt den Cursor schrittweise vor. Beim Durchlaufen einer Meldung: • Einmal drücken, um die Laufgeschwindigkeit zu erhöhen. • Erneut drücken zum Anhalten. • Noch einmal drücken, um zur StandardLaufgeschwindigkeit zurückzukehren. • Erneutes Drücken wiederholt den Zyklus.
Home-Bildschirm Auf dem Home-Bildschirm werden vom Benutzer konfigurierbare Informationen über das System angezeigt. Dieser Bildschirm wird beim normalen Systembetrieb angezeigt, wenn keine Status- oder Fehlermeldungen anstehen. Wenn sich das System im Standbyzustand befindet, erlischt die LCD-Hintergrundbeleuchtung nach 5 Minuten Inaktivität, wenn keine Fehlermeldungen vorliegen. Um den HomeBildschirm anzuzeigen, drücken Sie eine der drei Steuertasten (Auswahl, Links oder Rechts).
Option Beschreibung Set error Wählen Sie SEL, um LCD-Fehlermeldungen in einem Format entsprechend der IPMI-Beschreibung im SELProtokoll anzuzeigen. Dies kann hilfreich dabei sein, eine LCD-Meldung mit einem SEL-Eintrag abzugleichen. Wählen Sie Simple, um LCD-Fehlermeldungen in einem vereinfachten benutzerfreundlichen Format anzuzeigen. Eine Liste der Meldungen in diesem Format finden Sie unter „Meldungen der LCD-Statusanzeige“ auf Seite 24.
Festplattenanzeigemuster 1 2 1 Festplattenstatusanzeige (grün und gelb) 2 Festplattenaktivitätsanzeige (grün) Laufwerkstatusanzeigemuster (nur RAID) Zustand Blinkt grün, zweimal pro Sekunde Laufwerk identifizieren/zum Entfernen vorbereiten Aus Laufwerk bereit zum Einsetzen oder Entfernen ANMERKUNG: Die Laufwerkstatusanzeige bleibt ausgeschaltet, bis alle Festplatten nach dem Einschalten des Systems initialisiert sind.
Anzeigen und Funktionen auf der Rückseite Abbildung 1-3. Anzeigen und Funktionen auf der Rückseite 1 16 2 15 14 Element Anzeige, Taste oder Anschluss 3 4 13 12 Symbol 5 6 11 7 10 9 8 Beschreibung 1 PCIe-Steckplatz 1 PCI Express (2. Generation) x8-Erweiterungssteckplatz (Länge 24,13 cm). 2 PCIe-Steckplatz 2 PCI Express (2. Generation) x4-Erweiterungssteckplatz (niedriges Profil mit maximaler Länge von 24,13 cm, Halter in Standardhöhe). 3 PCIe-Steckplatz 3 PCI Express (2.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 6 PCIe-Steckplatz 6 PCI Express (2. Generation) x8-Erweiterungssteckplatz (Länge 24,13 cm). 7 Netzteile (2) 1100-W-Netzteile. 8 Systemidentifikationstaste Die Identifikationstasten auf der Vorderund Rückseite dienen dazu, ein bestimmtes System innerhalb eines Racks zu lokalisieren.
Richtlinien für das Anschließen von externen Geräten • Schalten Sie die Stromversorgung des Systems und der externen Geräte aus, bevor Sie ein neues externes Gerät anschließen. Schalten Sie zuerst alle externen Geräte ein, bevor Sie das System einschalten (es sei denn, die Gerätedokumentation gibt etwas anderes an). • Stellen Sie sicher, dass ein geeigneter Treiber für das angeschlossene Gerät auf dem System installiert wurde.
Anzeigecodes für Stromversorgung Die Anzeigen an den Netzteilen informieren darüber, ob die Stromversorgung aktiv ist oder ein Fehler aufgetreten ist. • Leuchtet nicht – Netzstrom ist nicht angeschlossen. • Grün – Im Standby-Zustand zeigt eine grüne Leuchte an, dass eine gültige Netzstromquelle mit dem Netzteil verbunden und das Netzteil in Betrieb ist. Wenn das System eingeschaltet ist, zeigt eine grüne Leuchte außerdem an, dass das Netzteil das System mit Gleichstrom versorgt.
Abbildung 1-4.
Meldungen der LCD-Statusanzeige Die LCD-Meldungen bestehen aus kurzen Textnachrichten, die sich auf Ereignisse beziehen, die im Systemereignisprotokoll (SEL) aufgezeichnet sind. Informationen über das SEL und zum Konfigurieren von Systemverwaltungseinstellungen finden Sie in der Dokumentation zu OpenManage™ Server Administrator unter support.dell.com/manuals.
Tabelle 1-1. Meldungen der LCD-Statusanzeige Code Text E1000 Failsafe voltage error. Contact support. Ursachen Korrekturmaßnahmen Überprüfen Sie das Trennen Sie das System Systemereignisprotokoll auf für 10 Sekunden von der kritische Fehlerereignisse. Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1114 Ambient Temp exceeds allowed range.
Code Text Ursachen Korrekturmaßnahmen E1211 RAID Controller battery failure. Check battery. RAID-Akku ist nicht vorhanden, fehlerhaft, oder lässt sich aufgrund von Temperaturproblemen nicht aufladen. Setzen Sie den RAIDAkkustecker neu ein. Siehe „RAID-Akku (optional)“ auf Seite 133 und „Fehlerbehebung bei der Systemkühlung“ auf Seite 175. E1216 3.3 V Regulator failure. Reseat PCIe cards. 3,3-V-Spannungsregler ist ausgefallen. Entfernen Sie die PCIeErweiterungskarten und setzen Sie sie neu ein.
Code Text E122E On-board regulator failed. Call support. Ursachen Korrekturmaßnahmen Einer der eingebauten Spannungsregler ist ausgefallen. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1243 CPU # VCORE Regulator failure. Contact Support. Prozessor-Spannungsregler ist ausgefallen. Setzen Sie den Prozessor neu ein.
Code Text E1410 System Fatal Error detected. Ursachen Korrekturmaßnahmen Ein schwerwiegender Systemfehler wurde festgestellt. Überprüfen Sie das LCD auf weitere Laufmeldungen. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1414 CPU # temp exceeding range. Check CPU heatsink. Der angegebene Prozessor befindet sich außerhalb des zulässigen Temperaturbereichs.
Code Text E141F CPU # protocol error. Power cycle AC. Ursachen Korrekturmaßnahmen Das System-BIOS hat einen Trennen Sie das System Prozessor-Protokollfehler für 10 Sekunden von der gemeldet. Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1420 CPU Bus Das System-BIOS hat einen parity error. Prozessor-Busparitätsfehler Power cycle gemeldet. AC.
Code Text E1610 Power Supply # (#### W) missing. Check power supply. Ursachen Korrekturmaßnahmen Das angegebene Netzteil Siehe „Fehlerbehebung wurde entfernt oder fehlt im bei Netzteilen“ auf System. Seite 175. E1614 Power Supply Das angegebene Netzteil ist Siehe „Fehlerbehebung bei Netzteilen“ auf # (#### W) ausgefallen. Seite 175. error. Check power supply. E1618 Predictive failure on Power Supply # (#### W). Check PSU.
Code Text Ursachen Korrekturmaßnahmen E1629 Power required > PSU wattage. Check PSU and config. Die Systemkonfiguration benötigt auch bei Drosselung mehr Strom als die Netzteile liefern können. Schalten Sie das System aus und überprüfen Sie die ordnungsgemäße Netzstromversorgung des Systems. Im Handbuch zum Einstieg finden Sie Informationen über die Anforderungen an die Systemstromversorgung. E1631 System power draw exceeded threshold. Contact support.
Code Text E1710 I/O channel check error. Review & clear SEL. Ursachen Korrekturmaßnahmen Das System-BIOS hat einen Überprüfen Sie das SEL E/A-Kanalprüffehler auf weitere Informationen gemeldet. und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1711 PCI parity error on Bus ## Device ## Function ##. PCI parity error on Slot #.
Code Text Ursachen Korrekturmaßnahmen Das System-BIOS hat einen PCI-Systemfehler bei einer Komponente im PCIKonfigurationsraum bei Bus ##, Gerät ## und Funktion ## gemeldet. Entfernen Sie die PCIeErweiterungskarten und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Erweiterungskarten“ auf Seite 186. Das System-BIOS hat einen PCI-Systemfehler bei einer Komponente im angegebenen Steckplatz gemeldet.
Code Text Ursachen E1715 Fatal I/O Das System-BIOS hat Error. Review festgestellt, dass ein & clear SEL. schwerwiegender Fehler im System aufgetreten ist. Korrekturmaßnahmen Überprüfen Sie das SEL auf weitere Informationen, und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1716 Chipset IERR Bus ## Dev ## Function ##. Review & clear SEL.
Code Text E171F PCIe fatal error on Bus ## Device ## Function ##. PCIe fatal error on Slot #. Review & clear SEL. Ursachen Korrekturmaßnahmen Das System-BIOS hat einen schwerwiegenden PCIeFehler bei einer Komponente im PCIKonfigurationsraum bei Bus ##, Gerät ## und Funktion ## gemeldet. Entfernen Sie die PCIeErweiterungskarten und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Erweiterungskarten“ auf Seite 186.
Code Text Ursachen Korrekturmaßnahmen E1A12 PCI Riser not Eine oder beide detected. Steckkarte(n) für Check Riser. Erweiterungskarten fehlt/fehlen. Deshalb lässt sich das System nicht hochfahren. Installieren Sie den fehlenden Riser neu. Siehe „Installieren von Erweiterungskarten-Riser 1“ auf Seite 127 und „Installieren von Erweiterungskarten-Riser 2“ auf Seite 129. E1813 Internal Dual Die interne zweifache SDSD Module Modulkarte ist ausgefallen. Card # failed. Check SD card.
Code Text E1A15 SAS cable B failure. Check connection. Ursachen Korrekturmaßnahmen SAS-Kabel B ist nicht vorhanden oder fehlerhaft. Befestigen Sie das Kabel. Ersetzen Sie das Kabel, falls das Problem weiterhin besteht. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E1A1D Control panel USB-Kabel zum Bedienfeld USB cable not fehlt oder ist defekt. detected. Check cable. Befestigen Sie das Kabel. Ersetzen Sie das Kabel, falls das Problem weiterhin besteht.
Code Text Ursachen Korrekturmaßnahmen E2013 BIOS unable to shadow memory. Check DIMMs. Das System-BIOS konnte sein Flash-Image nicht in den Speicher kopieren. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 177. E2014 CMOS RAM failure. Power cycle AC. CMOS-Fehler. CMOS-RAM Trennen Sie das System funktioniert nicht korrekt. für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203.
Code Text Ursachen Korrekturmaßnahmen E2017 Timer refresh Fehler bei der failure. Zeitgeberaktualisierung. Power cycle AC. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E2018 Programmable Timer error. Power cycle AC. Fehler beim programmierbaren Intervallzeitgeber. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu.
Code Text E201B Keyboard controller error. Power cycle AC. Ursachen Korrekturmaßnahmen Fehler des Tastaturcontrollers. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. E201C SMI SMI-Initialisierungsfehler initialization (System Management failure. Interrupt). Power cycle AC. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu.
Code Text Ursachen Korrekturmaßnahmen E2020 CPU Prozessorconfiguration Konfigurationsfehler. failure. Check screen message. Auf dem Bildschirm werden spezifische Fehlermeldungen angezeigt. Siehe „Fehlerbehebung bei den Prozessoren“ auf Seite 187. E2021 Incorrect Incorrect memory memory configuration. configuration. Review User Guide. Auf dem Bildschirm werden spezifische Fehlermeldungen angezeigt. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 177. E2022 General failure during POST.
Code Text Ursachen Korrekturmaßnahmen E2111 SBE log disabled on DIMM ##. Reseat DIMM. Das System-BIOS hat die Protokollierung von Speicher-Einfachbitfehlern (korrigierbar) deaktiviert und setzt die SBEProtokollierung erst beim nächsten Neustart fort. „##“ ist das betreffende Speichermodul. Setzen Sie das Speichermodul neu im Sockel ein. E2112 Memory spared on DIMM ##. Power cycle AC. Das System-BIOS hat den Speicher ausgelassen, weil zu viele Fehler darin festgestellt wurden.
Code Text Ursachen Korrekturmaßnahmen W1100 CPU VCORE Regulator temp exceeding range. Check fans. Die SpannungsreglerTemperatur hat den zulässigen Bereich überschritten. Siehe „Fehlerbehebung bei der Systemkühlung“ auf Seite 175. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. W1102 Mem Voltage Regulator temp exceeding range. Check fans Die SpannungsreglerTemperatur hat den zulässigen Bereich überschritten.
Systemmeldungen Systemmeldungen werden auf dem Bildschirm angezeigt, um Sie auf mögliche Systemprobleme aufmerksam zu machen. ANMERKUNG: Wenn eine Systemmeldung ausgegeben wird, die nicht in der Tabelle aufgeführt ist, können Sie die Erklärung der Meldung und die empfohlene Maßnahme in der Dokumentation zur Anwendung, welche bei der Anzeige der Meldung ausgeführt wird, oder in der Dokumentation zum Betriebssystem, nachschlagen. Tabelle 1-2.
Meldung Ursachen Korrekturmaßnahmen Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving. Die Speicherkonfiguration hat sich geändert (zum Beispiel ist ein Speichermodul ausgefallen), so dass Knoten-Interleaving nicht unterstützt wird. Das System funktioniert zwar, aber ohne KnotenInterleaving. Stellen Sie sicher, dass die Speichermodule in einer Konfiguration installiert werden, die KnotenInterleaving unterstützt.
Meldung Ursachen Korrekturmaßnahmen Alert! Redundant memory disabled! Memory configuration does not support redundant memory. Speicherredundanz wurde im System-Setup-Programm aktiviert, aber die derzeitige Konfiguration unterstützt keinen redundanten Speicher. Möglicherweise ist ein Speichermodul fehlerhaft. Überprüfen Sie die Speichermodule auf Defekte. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 177. Setzen Sie gegebenenfalls die Speichereinstellung zurück.
Meldung Ursachen Korrekturmaßnahmen Caution! NVRAM_CLR jumper is installed on system board. NVRAM_CLR-Jumper ist in der Einstellung zum Löschen installiert. CMOS wurde gelöscht. Setzen Sie den NVRAM_CLR-Jumper auf die Standardposition (Kontaktstifte 3 und 5). Die Position des Jumpers ist in Abbildung 6-1 dargestellt. Starten Sie das System neu und legen Sie die BIOSEinstellungen erneut fest. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 63.
Meldung Ursachen Korrekturmaßnahmen Current boot mode is set to UEFI. Please ensure compatible bootable media is available. Use the system setup program to change the boot mode as needed. Das System konnte nicht gestartet werden, da UEFI Boot Mode im BIOS aktiviert ist und das Startbetriebssystem UEFI nicht unterstützt. Stellen Sie sicher, dass der Boot Mode korrekt eingestellt ist und das entsprechende startfähige Medium verfügbar ist.
Meldung Ursachen Korrekturmaßnahmen General failure. Das Betriebssystem konnte den Befehl nicht ausführen. Diese Meldung wird normalerweise von genaueren Angaben begleitet. Notieren Sie sich die Informationen und führen Sie die entsprechenden Maßnahmen durch, um das Problem zu beheben. Invalid configuration information please run SETUP program. Eine unzulässige Systemkonfiguration hat zu einem Systemhalt geführt. Führen Sie das SystemSetup-Programm aus und überprüfen Sie die Einstellungen.
Meldung Ursachen Korrekturmaßnahmen Keyboard fuse has Am Tastaturanschluss wurde Siehe „Wie Sie Hilfe failed. ein Überstromzustand bekommen“ auf Seite 203. festgestellt. Local keyboard Die USB-Ports sind im may not work System-BIOS deaktiviert. because all user accessible USB ports are disabled. If operating locally, power cycle the system and enter system setup program to change settings.
Meldung Ursachen Korrekturmaßnahmen No boot device available. Fehlerhaft oder nicht vorhanden: Subsystem für optisches Laufwerk, Festplatte oder Festplattensubsystem; oder es ist nicht-startfähiger USB-Stick installiert. Verwenden Sie einen startfähigen USB-Stick, eine startfähige CD oder ein startfähiges Festplattenlaufwerk.
Meldung Ursachen Korrekturmaßnahmen No timer tick interrupt. Defekte Systemplatine. Siehe „Wie Sie Hilfe bekommen“ auf Seite 203. PCI BIOS failed to install. Prüfsummenfehler bei PCIeGeräte-BIOS (OptionsROM) während des Shadowing erkannt. Setzen Sie die Erweiterungskarte(n) neu ein. Stellen Sie sicher, dass alle erforderlichen Kabel sicher mit den Erweiterungskarten verbunden sind. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Erweiterungskarten“ auf Seite 186.
Meldung Ursachen Korrekturmaßnahmen Read fault. Das Betriebssystem kann vom Festplattenlaufwerk, dem optischen Laufwerk oder dem USB-Gerät nicht lesen, das System konnte einen bestimmten Sektor auf der Festplatte nicht finden, oder der angeforderte Sektor ist defekt. Ersetzen Sie das optische Medium, das USB-Medium oder das USB-Gerät. Stellen Sie sicher, dass die SASRückwandplatinen-, USBoder SATA-Kabel korrekt angeschlossen sind.
Meldung Ursachen Korrekturmaßnahmen Requested sector not found. Das Festplattenlaufwerk, USB-Gerät oder USBMedium ist defekt. Ersetzen Sie das USBMedium oder das Gerät. Stellen Sie sicher, dass die USB- oder SASRückwandplatinenkabel korrekt angeschlossen sind. Entsprechende Informationen zu den im System installierten Laufwerken finden Sie unter „Fehlerbehebung bei einem USB-Gerät“ auf Seite 168 oder „Fehlerbehebung bei einem Festplattenlaufwerk“ auf Seite 183. Allgemeiner Systemfehler.
Meldung Ursachen Korrekturmaßnahmen Time-of-day not set - please run SETUP program. Die Einstellungen für Time oder Date sind falsch; fehlerhafte Systembatterie. Überprüfen Sie die Uhrzeitund Datumseinstellungen. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 63. Besteht das Problem weiterhin, ersetzen Sie die Systembatterie. Siehe „Systembatterie“ auf Seite 147. Timer chip Defekte Systemplatine. counter 2 failed. Siehe „Wie Sie Hilfe bekommen“ auf Seite 203.
Meldung Ursachen Korrekturmaßnahmen Unable to launch System Services image. System halted! System wurde nach Tastendruck angehalten, weil das System Services-Image in der System-Firmware beschädigt ist oder aufgrund eines Systemplatinenaustauschs verloren ging. Starten Sie das System neu und aktualisieren Sie den Lifecycle Controller, indem Sie das Lifecycle Controller Dell Update Package (DUP) ausführen.
Meldung Ursachen Korrekturmaßnahmen Unsupported memory configuration. DIMM mismatch across slots detected: x,x,... Unzulässige Speicherkonfiguration erkannt. Speichermodule in den angegebenen Sockeln sind nicht identisch. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 105.
Meldung Ursachen Korrekturmaßnahmen Warning! Power required exceeds PSU wattage. Check PSU and system configuration. Die Systemkonfiguration aus Prozessoren, Speichermodulen und Erweiterungskarten wird möglicherweise von den Netzteilen nicht unterstützt. Falls für Systemkomponenten gerade ein Upgrade erfolgt ist, versetzen Sie das System wieder in die vorherige Konfiguration zurück. Wenn das System ohne diese Warnmeldung startet, werden die ersetzten Komponenten von diesem Netzteil nicht unterstützt.
Meldung Ursachen Korrekturmaßnahmen Incorrect memory configuration CPU n. Die DIMM-Gruppe für CPU n ist falsch konfiguriert und hat den Systemhalt verursacht. Informationen zur Speicherkonfiguration finden Sie unter „Richtlinien zur Installation von Speichermodulen“ auf Seite 105. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung beim Systemspeicher“ auf Seite 177.
Meldung Ursachen Korrekturmaßnahmen Warning: The installed memory configuration is not optimal. For more information on valid memory configurations, please see the system documentation on the technical support web site. Unzulässige Speicherkonfiguration erkannt. Das System läuft, jedoch mit eingeschränkter Funktionalität. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 105.
Diagnosemeldungen Die Diagnoseprogramme des Systems geben eventuell Meldungen aus. Weitere Informationen zur Systemdiagnose finden Sie unter „Ausführen der Systemdiagnose“ auf Seite 189. Alarmmeldungen Die Systemverwaltungssoftware erzeugt Alarmmeldungen für das System. Alarmmeldungen bestehen aus Informations-, Status-, Warn- und Fehlermeldungen zu Laufwerks-, Temperatur-, Lüfter- und Stromversorgungsbedingungen.
Wissenswertes zum System
Verwenden des System-SetupProgramms und des UEFI-BootManagers Das System-Setup-Programm ermöglicht das Verwalten der Systemhardware und das Festlegen von Optionen auf BIOS-Ebene.
Der Startmodus wird im Feld Boot Mode des „Bildschirm „Boot Settings“ (Systemstarteinstellungen)“ auf Seite 71 im System-Setup-Programm ausgewählt. Installieren Sie nach dem Festlegen des Startmodus das Betriebssystem in diesem Modus. Starten Sie danach das System im gleichen Startmodus (BIOS oder UEFI), um auf das installierte Betriebssystem zuzugreifen. Wenn Sie versuchen, das Betriebssystem in dem anderen Startmodus hochzufahren, führt dies zum sofortigen Anhalten des Systems beim Start.
Verwenden der Steuertasten des System-Setup-Programms Tasten Maßnahme Pfeil-nach-oben-Taste oder Zurück zum vorherigen Feld. Pfeil-nach-unten-Taste oder Weiter zum nächsten Feld. Leertaste, <+>, < –>, Pfeil-nach-links- und Pfeilnach-rechts-Taste Zeigt die möglichen Einstellungen eines Feldes nacheinander an. In vielen Feldern kann der zutreffende Wert auch eingegeben werden.
Optionen des System-Setup-Programms Hauptbildschirm ANMERKUNG: Welche Optionen angezeigt werden, hängt von der Konfiguration des Systems ab. ANMERKUNG: Die Standardeinstellungen des System-Setup-Programms sind in den folgenden Abschnitten gegebenenfalls bei den jeweiligen Optionen angegeben.
Option Beschreibung System Time Uhrzeiteinstellung der internen Systemuhr. System Date Datumseinstellung des internen Kalenders. Memory Settings Zeigt Informationen zum installierten Arbeitsspeicher an. Siehe „Bildschirm „Memory Settings“ (Speichereinstellungen)“ auf Seite 69. Processor Settings Zeigt Informationen zu den Prozessoren an (Geschwindigkeit, Cache-Größe usw.). Siehe „Bildschirm „Processor Settings“ (Prozessoreinstellungen)“ auf Seite 69.
Option Beschreibung Power Management Ermöglicht das Festlegen von vorkonfigurierten oder individuell angepassten Energieverbrauchseinstellungen für Prozessor(en), Lüfter und Speichermodule. Siehe „Bildschirm „Power Management“ (Energieverwaltung)“ auf Seite 75. System Security Zeigt den Bildschirm zur Konfiguration der Systemund Setup-Kennwortfunktionen an.
Bildschirm „Memory Settings“ (Speichereinstellungen) Option Beschreibung System Memory Size Zeigt die Größe des Systemspeichers an. System Memory Type Zeigt den Typ des Systemspeichers an. System Memory Speed Zeigt die Systemspeichertaktrate an. Video Memory Zeigt die Größe des Grafikspeichers an. System Memory Testing (Standardeinstellung Enabled) Legt fest, ob Systemspeichertests beim Start ausgeführt werden. Die Optionen sind Enabled und Disabled.
Option Beschreibung CPU Virtualization Technology (Standardeinstellung Enabled) Enabled ermöglicht der Virtualisierungssoftware, die im Prozessor integrierte Virtualization Technology zu nutzen. ANMERKUNG: Deaktivieren Sie diese Option, wenn auf dem System keine Virtualisierungssoftware eingesetzt wird. DRAM Prefetcher (Standardeinstellung Enabled) Aktiviert oder deaktiviert den DRAM-Prefetcher (Vorabruffunktion).
Bildschirm „SATA Settings“ (SATA-Einstellungen) Option Beschreibung Embedded SATA (Standardeinstellung ATA) ATA Mode aktiviert den integrierten SATA-Controller. Off deaktiviert den Controller. Port A (Standardeinstellung Auto) Auto aktiviert die BIOS-Unterstützung für das an den SATA-Port A angeschlossene Gerät. Off deaktiviert BIOS-Unterstützung für das Gerät.
Option Beschreibung Hard-Disk Drive Sequence Legt die Reihenfolge der Festplattenlaufwerke fest, von denen das BIOS während des Systemstarts zu starten versucht. USB Flash Drive Emulation Type Legt den Emulationstyp für das USB-Flash-Laufwerk fest. Wenn Boot Mode auf UEFI gesetzt ist, ist dieses Feld deaktiviert. Boot Sequence Retry (Standardeinstellung Disabled) Wenn diese Option aktiviert ist, versucht das System bei einem fehlgeschlagenen Startversuch nach 30 Sekunden erneut zu starten.
Option Beschreibung Embedded NIC2 (Standardeinstellung Enabled) Aktiviert oder deaktiviert die Betriebssystemschnittstelle der integrierten NICs. Auf die NICs kann auch über den Systemverwaltungscontroller zugegriffen werden. Embedded Gb NICx (Standardeinstellung Enabled) Aktiviert oder deaktiviert den integrierten NIC. Die Optionen sind Enabled und Enabled with PXE. PXESupport ermöglicht dem System, vom Netzwerk zu starten. MAC-Adresse Zeigt die MAC-Adresse für den integrierten 10/100/1000-NIC an.
Bildschirm „Serial Communication“ (Serielle Kommunikation) Option Beschreibung Serial Communication (Standardeinstellung On without Console Redirection) Legt fest, ob serielle Datengeräte (Serial Device 1 und Serial Device 2) im BIOS aktiviert sind. Auch BIOSKonsolenumleitung kann aktiviert werden und die verwendete Portadresse lässt sich festlegen. Die Optionen sind On without Console Redirection, On with Console Redirection via COM1, On with Console Redirection via COM2 und Off.
Bildschirm „Power Management“ (Energieverwaltung) Option Beschreibung Power Management (Standardeinstellung OS Control) Optionen sind OS Control, Active Power Controller, Custom oder Maximum Performance. Bei allen Einstellungen mit Ausnahme von Custom sind die Energieverwaltungsoptionen im BIOS vorkonfiguriert: • Bei der Einstellung OS Control wird die Prozessorleistung auf OS DBPM gesetzt, die Lüfterleistung auf Minimum Power und die Speicherleistung auf Maximum Performance.
Bildschirm „System Security“ (Systemsicherheit) Option Beschreibung System Password Zeigt den aktuellen Status der Kennwortsicherheitsfunktion an und ermöglicht die Zuweisung und Überprüfung eines neuen Systemkennworts. ANMERKUNG: Weitere Informationen finden Sie unter „Verwenden des Systemkennworts“ auf Seite 80. Setup Password Schränkt den Zugriff auf das System-Setup-Programm durch ein Setup-Kennwort ein.
Option Beschreibung AC Power Recovery (Standardeinstellung Last) Bestimmt, wie das System reagiert, wenn die Stromversorgung wiederhergestellt wird. Bei der Einstellung Last kehrt das System in den letzten vor dem Stromausfall vorhandenen Netzstromzustand zurück. On schaltet das System ein, sobald die Stromversorgung wiederhergestellt ist. Bei der Einstellung Off bleibt das System nach Wiederherstellen der Stromversorgung ausgeschaltet.
Aufrufen des UEFI-Boot-Managers ANMERKUNG: Damit ein Betriebssystem im UEFI-Boot-Modus installiert werden kann, muss es 64-Bit UEFI-kompatibel sein (zum Beispiel Microsoft Windows Server 2008 x64). DOS und 32-Bit-Betriebssysteme lassen sich nur im BIOS-Boot-Modus installieren. ANMERKUNG: Der Startmodus muss im System-Setup-Programm auf UEFI gesetzt sein, um den UEFI-Boot-Manager aufrufen zu können.
Bildschirm „UEFI Boot Manager“ (UEFI-Boot-Manager) Option Beschreibung Continue Das System versucht von den Geräten in der Startreihenfolge zu starten, beginnend mit dem ersten Eintrag. Wenn der Startvorgang fehlschlägt, setzt das Gerät den Vorgang mit dem nächsten Gerät in der Startreihenfolge fort, bis ein Startvorgang erfolgreich ist oder keine weiteren Startoptionen vorhanden sind. Zeigt die Liste der verfügbaren Startoptionen an (markiert mit Sternchen).
Bildschirm „System Utilities“ (Systemdienstprogramme) Option Beschreibung System Setup Ruft das System-Setup-Programm auf, ohne einen Neustart auszuführen. System Services Startet das System neu und ruft den Lifecycle Controller auf, der die Ausführung von Programmen wie der Systemdiagnose ermöglicht. BIOS Boot Manager Ruft die Liste der Startoptionen auf BIOS-Ebene auf, ohne einen Neustart auszuführen.
Zuweisen eines Systemkennworts Bevor Sie ein Systemkennwort zuweisen, muss das System-Setup-Programm aufgerufen und die Option System Password aktiviert werden. Wenn ein Systemkennwort zugewiesen wurde, ist System Password auf Enabled gesetzt. Wenn Password Status auf Unlocked gesetzt ist, können Sie das Systemkennwort ändern. Bei der Einstellung Locked können Sie das Systemkennwort nicht ändern.
5 Um das Kennwort zu bestätigen, geben Sie dieses erneut ein und drücken Sie die Eingabetaste. System Password hat jetzt die Einstellung Enabled. Sie können nun das System-Setup-Programm beenden und das System einsetzen. 6 Starten Sie entweder das System neu, um den Kennwortschutz wirksam werden zu lassen, oder setzen Sie Ihre Arbeit fort. ANMERKUNG: Der Kennwortschutz wird erst wirksam, wenn das System neu gestartet wird.
Auch nach dem Herunterfahren und Neustarten des Systems wird die Fehlermeldung angezeigt, bis das korrekte Kennwort eingegeben wurde. ANMERKUNG: Die Option Password Status kann in Verbindung mit den Optionen System Password und Setup Password eingesetzt werden, um das System vor unerlaubtem Zugriff zu schützen. Löschen oder Ändern eines bestehenden Systemkennworts 1 Rufen Sie das System-Setup-Programm auf und wählen Sie System Security.
Wenn Sie das Kennwort bestätigen, wird die Option Setup Password auf Enabled gesetzt. Beim nächsten Aufruf des System-Setup-Programms fordert Sie das System zur Eingabe des Setup-Kennworts auf. Eine Änderung der Option Setup Password wird sofort wirksam (das System muss nicht neu gestartet werden).
Integrierte Systemverwaltung Der Lifecycle Controller ist ein integriertes Dienstprogramm, das Systemverwaltungsaufgaben aus einer integrierten Umgebung während der gesamten Server-Lebensdauer ermöglicht. Der Lifecycle-Controller lässt sich während des Startvorgangs aufrufen und unabhängig vom Betriebssystem verwenden. ANMERKUNG: Bestimmte Plattformkonfigurationen unterstützen möglicherweise nicht alle Funktionen des Lifecycle-Controllers.
Zudem ermöglicht das iDRAC6-Konfigurationsprogramm folgende Funktionen: • Konfigurieren, Aktivieren oder Deaktivieren des lokalen iDRAC6Netzwerks über den reservierten iDRAC6 Enterprise-Kartenport oder den integrierten NIC1 • IPMI über LAN aktivieren oder deaktivieren • LAN-PET-Ziel (Plattformereignis-Trap) aktivieren • Virtual-Media-Geräte verbinden oder trennen • Benutzername und Kennwort des Administrators ändern und Benutzerrechte verwalten • SEL-Meldungen (Systemereignisprotokoll) anzeigen o
Installieren von Systemkomponenten Empfohlene Werkzeuge Für die in diesem Abschnitt beschriebenen Maßnahmen benötigen Sie gegebenenfalls folgende Werkzeuge: • Schlüssel für das Systemschloss • Kreuzschlitzschraubendreher der Größen 1 und 2 • Torx-Schraubendreher der Größen T8 und T10 • Erdungsarmband Das Innere des Systems WARNUNG: Beim Anheben des Systems sollten Sie sich stets von jemand anders helfen lassen. Um Verletzungen zu vermeiden, sollten Sie nicht versuchen, das System allein zu bewegen.
Abbildung 3-1.
Frontverkleidung (optional) Entfernen der Frontverkleidung 1 Entriegeln Sie das Systemschloss am linken Rand der Frontverkleidung. 2 Heben Sie die Sperrklinke neben dem Schloss an. 3 Schwenken Sie die linke Seite der Frontverkleidung von der Vorderseite des Systems weg. 4 Lösen Sie die rechte Seite der Frontverkleidung aus dem Haken und nehmen Sie die Frontverkleidung vom System ab. Siehe Abbildung 3-2. Abbildung 3-2.
Öffnen und Schließen des Systems WARNUNG: Beim Anheben des Systems sollten Sie sich stets von jemand anders helfen lassen. Um Verletzungen zu vermeiden, sollten Sie nicht versuchen, das System allein zu bewegen. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-3. System öffnen und schließen 1 2 3 1 Freigabehebel 3 Abdeckung 2 Verriegelung Schließen des Systems 1 Positionieren Sie die Abdeckung auf dem Gehäuse und versetzen Sie es leicht zur Systemrückseite, damit die Aussparungen auf den Seiten der Abdeckung in die entsprechenden Haken auf den Gehäuseseiten greifen. Siehe Abbildung 3-3.
4 Drehen Sie die Verriegelung des Freigabehebels im Uhrzeigersinn, um die Abdeckung zu sichern. 5 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. Festplattenlaufwerke Alle Laufwerke sind über die SAS/SATA-Rückwandplatine in der vorderen Gehäusebaugruppe mit der Systemplatine verbunden. Die Festplatten befinden sich in hot-swap-fähigen Laufwerkträgern, die in die Festplattenschächte passen.
Entfernen eines Laufwerkplatzhalters VORSICHTSHINWEIS: Um eine ausreichende Systemkühlung zu gewährleisten, müssen alle leeren Festplattenschächte mit entsprechenden Platzhaltern belegt sein. 1 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 89. 2 Fassen Sie den Laufwerkplatzhalter an der Vorderseite an, drücken Sie die Freigabetaste und schieben Sie den Platzhalter vollständig aus dem Laufwerkschacht. Siehe Abbildung 3-4. Abbildung 3-4.
Installieren eines Festplattenplatzhalters 1 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 89. 2 Schieben Sie den Laufwerkplatzhalter in den Laufwerkschacht, bis die Freigabetaste einrastet. 3 Bringen Sie gegebenenfalls die Frontverkleidung wieder an. Siehe „Installieren der Frontverkleidung“ auf Seite 89. Entfernen eines Laufwerkträgers VORSICHTSHINWEIS: Stellen Sie sicher, dass das Betriebssystem Hot-SwapLaufwerkinstallation unterstützt.
6 Bringen Sie gegebenenfalls die Frontverkleidung wieder an. Siehe „Installieren der Frontverkleidung“ auf Seite 89. Abbildung 3-5. Festplattenträger entfernen und installieren 1 2 3 1 Freigabetaste 3 Bügel des Festplattenträgers 2 Festplattenträger Installieren eines Laufwerkträgers VORSICHTSHINWEIS: Verwenden Sie nur Festplatten, die geprüft und für den Einsatz mit der SAS/SATA-Rückwandplatine zugelassen sind.
3 Drücken Sie auf die Freigabetaste auf der Vorderseite des Festplattenträgers und öffnen Sie den Griff. 4 Schieben Sie den Laufwerkträger in den Schacht, bis der Träger die Rückwandplatine berührt. 5 Schließen Sie den Bügel des Laufwerkträgers, um das Laufwerk zu verriegeln. Entfernen einer Festplatte aus einem Laufwerkträger Entfernen Sie die Schrauben von den Führungsschienen am Laufwerkträger und trennen Sie die Festplatte vom Träger. Siehe Abbildung 3-6. Abbildung 3-6.
Installieren einer Festplatte im Laufwerkträger 1 Führen Sie die Festplatte in den Festplattenträger ein, wobei sich das Anschlussende des Laufwerks hinten befindet. Siehe Abbildung 3-6. 2 Richten Sie die Schraublöcher in der Festplatte mit den hinteren Löchern am Laufwerkträger aus. 3 Befestigen Sie die vier Schrauben, um die Festplatte am Laufwerkträger zu sichern. Optisches Laufwerk Das System ist optional mit einem optischen SATA DVD-ROM- oder DVD+/-RW-Laufwerk in Flachbauweise ausgestattet.
5 Um das Laufwerk zu entfernen, drücken Sie die blaue Sperrklinke nach unten und drücken Sie sie in Richtung der Systemvorderseite. Siehe Abbildung 3-7. 6 Schieben Sie das optische Laufwerk aus dem System, bis es vollständig aus dem Laufwerkschacht entfernt ist. 7 Wenn Sie kein neues optisches Laufwerk einsetzen, installieren Sie den Platzhalter für das optische Laufwerk. 8 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91.
Installation eines optischen Laufwerks VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Netzteile Das System unterstützt zwei hot-swap-fähige 1100-W-Netzteile. Wenn zwei Netzteile installiert sind, sorgt das zweite Netzteil für eine redundante Stromversorgung. In der redundanten Betriebsart wird die Stromlast auf beide Netzteile verteilt, um die Effizienz zu maximieren. Wenn ein Netzteil bei eingeschaltetem System entfernt wird, übernimmt das zweite Netzteil die gesamte Stromlast. In Tabelle 3-1 sind die redundanten Netzteilbetriebsarten aufgeführt. Tabelle 3-1.
Abbildung 3-8. Netzteil entfernen und installieren 1 2 3 1 Netzteil 3 Sperrklinke 2 Klettstreifen Installieren eines Netzteils 1 Stellen Sie sicher, dass die Netzteile vom gleichen Typ sind und die gleiche maximale Ausgangsleistung haben. ANMERKUNG: Die maximale Leistungsabgabe (in Watt) ist auf dem Netzteiletikett angegeben. 2 Entfernen Sie gegebenenfalls den Netzteilplatzhalter. Siehe „Entfernen des Netzteilplatzhalters“ auf Seite 102.
VORSICHTSHINWEIS: Wenn Sie das Netzstromkabel anschließen, sichern Sie es mit dem Klettband. ANMERKUNG: Wenn Sie ein neues Netzteil installieren bzw. bei laufendem Betrieb austauschen oder hinzufügen, braucht das System einige Sekunden, um das Netzteil zu erkennen und seinen Status zu ermitteln. Die Statusanzeige des Netzteils wechselt zu grün, um anzuzeigen, dass das Netzteil ordnungsgemäß funktioniert.
1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen und Schließen des Systems“ auf Seite 90. 3 Entfernen Sie den RAID-Akku aus dem Akkuträger. Siehe Abbildung 3-9. 4 Fassen Sie das Kühlgehäuse an den Anfasspunkten an und heben Sie es vorsichtig aus dem System. Siehe Abbildung 3-9. Abbildung 3-9.
Installieren des Kühlgehäuses ANMERKUNG: Um das Kühlgehäuse korrekt im Systemgehäuse ausrichten zu können, müssen Sie darauf achten, dass die Kabel entlang der Systemgehäusewand verlegt sind. 1 Senken Sie das Kühlgehäuse in das System ab und richten Sie die Vorsprünge am Kühlgehäuse mit den Aussparungen am Systemgehäuse aus. Siehe Abbildung 3-9. 2 Setzen Sie den RAID-Akku in den Akkuträger im Kühlgehäuse ein. Siehe „Installieren des RAID-Akkus“ auf Seite 134. 3 Schließen Sie das System.
Richtlinien zur Installation von Speichermodulen Um eine optimale Leistung des Systems zu gewährleisten, beachten Sie bei der Konfiguration des Systemspeichers die folgenden allgemeinen Richtlinien: ANMERKUNG: Bei Speicherkonfigurationen, die diesen Richtlinien nicht entsprechen, startet das System unter Umständen nicht und es erfolgt keine Bildschirmausgabe. • DIMMs müssen für jeden Prozessor in einem Satz aus vier oder zwei identischen DIMMs installiert werden (zum Beispiel A1/A2, A3/A4).
Unterstützung für Speicherredundanz Speicherredundanz wird bei Systemen unterstützt, bei denen eine der vollständig belegten Speicherkonfigurationen aus Tabelle 3-2 vorliegt. Die Speicherredundanzfunktion muss im Bildschirm Memory Settings (Speichereinstellungen) des System-Setup-Programms aktiviert werden. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 63. ANMERKUNG: Die Funktionen Speicherredundanz und Knoten-Interleaving können nicht gleichzeitig eingesetzt werden.
Tabelle 3-2. Speicherkonfigurationen Systemkapazität (in GB) Anzahl der DIMMs DIMM-Größe (in GB) DIMM-Typ Organisation ANMERKUNG: Die DIMMs A1-A8 sind Prozessor 1 zugewiesen und die DIMMs B1-B8 sind Prozessor 2 zugewiesen.
Installieren von Speichermodulen WARNUNG: Die Speichermodule bleiben nach dem Ausschalten des Systems eine Zeit lang auf hoher Temperatur. Lassen Sie die Speichermodule ausreichend lange abkühlen, bevor Sie sie berühren. Fassen Sie die Speichermodule nur an den Kanten an. Vermeiden Sie das Berühren von Komponenten auf dem Speichermodul und an den Kontakten. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-10. Speichermodul installieren und entfernen 1 2 3 1 Speichermodul 3 Passung 2 Auswurfhebel (2) 6 Richten Sie den Stecker des Speichermoduls an den Abgleichmarkierungen des Speichermodulsockels aus und setzen Sie das Speichermodul in den Sockel ein. ANMERKUNG: Die Passung im Speichermodulsockel sorgt dafür, dass die Speichermodule nicht verkehrt herum installiert werden können. 7 Drücken Sie das Speichermodul mit den Daumen nach unten und sichern Sie so das Modul im Sockel.
9 Setzen Sie das Kühlgehäuse wieder ein. Siehe „Installieren des Kühlgehäuses“ auf Seite 104. 10 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 11 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. 12 Bringen Sie gegebenenfalls die Frontverkleidung wieder an. Siehe „Installieren der Frontverkleidung“ auf Seite 89.
VORSICHTSHINWEIS: Um eine ordnungsgemäße Kühlung zu gewährleisten, müssen in allen nicht belegten Speichersockeln Speichermodulplatzhalter installiert werden. Entfernen Sie Speichermodulplatzhalter nur dann, wenn Sie in diesen Sockeln Speichermodule installieren wollen. 1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 89. 3 Öffnen Sie das System.
Lüfter Das System enthält in einer Lüfterbaugruppe sechs hot-swap-fähige Lüfter, die die Prozessoren, Erweiterungskarten und Speichermodule kühlen. ANMERKUNG: Wenn mit einem bestimmten Lüfter ein Problem auftritt, wird die Lüfternummer in der Systemverwaltungssoftware angegeben, wodurch Sie den richtigen Lüfter anhand der Nummern an der Lüfterbaugruppe leicht identifizieren und austauschen können.
Abbildung 3-11.
Installieren eines Lüfters WARNUNG: Das Öffnen und Entfernen der Systemabdeckung bei eingeschaltetem System birgt die Gefahr eines elektrischen Schlags. Üben Sie äußerste Vorsicht, wenn Sie Lüfter entfernen oder installieren. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-12.
Installieren der Lüfterbaugruppe VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
1 Schalten Sie das System und die Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 90. 3 Lokalisieren Sie den USB-Anschluss auf der Bedienfeldplatine. Siehe Abbildung 3-28. 4 Setzen Sie den USB-Speicherstick in den USB-Anschluss ein. Siehe Abbildung 3-13. 5 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91.
Interner NIC-Hardwareschlüssel Künftige zusätzliche Funktionsmerkmale für die im System integrierten NICs werden durch Einsetzen eines optionalen NIC-Hardwareschlüssels im Sockel iSCSI KEY auf der Systemplatine aktiviert. Siehe Abbildung 6-1. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-14. NIC-Hardwareschlüssel entfernen und installieren 1 2 1 NIC-Hardwareschlüssel 2 ISCSI KEY-Anschluss 5 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 6 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
Erweiterungskarten und Erweiterungskarten-Riser Richtlinien zur Installation von Erweiterungskarten Das System unterstützt bis zu sechs PCIe-Erweiterungskarten der 2. Generation in den Steckplätzen auf der Systemplatine sowie zwei Erweiterungskarten-Risern. Die Position der Erweiterungssteckplätze auf der Systemplatine können Sie Abbildung 6-1 entnehmen und die Position der Erweiterungssteckplätze auf den Erweiterungskarten-Risern können Sie Abbildung 6-4 und Abbildung 6-5 entnehmen.
VORSICHTSHINWEIS: Um eine ordnungsgemäße Kühlung zu gewährleisten, dürfen nur zwei der sechs Erweiterungskarten mehr als 15 W Leistung aufnehmen (maximal bis zu 25 W), den integrierten Speichercontroller nicht eingerechnet. Tabelle 3-3 enthält Vorschläge für die Installation von Erweiterungskarten hinsichtlich bestmöglicher Kühlung und mechanischer Unterbringung. Die Erweiterungskarten mit der höchsten Priorität sollten als erste installiert werden und dabei die entsprechende Steckplatzpriorität erhalten.
Installieren einer Erweiterungskarte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-15. Erweiterungskarte installieren und entfernen 1 2 3 1 Erweiterungskartenverriegelung 3 Erweiterungskartensteckplatz 2 Erweiterungskarte 9 Verbinden Sie gegebenenfalls die Kabel mit der Erweiterungskarte. 10 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 11 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
Entfernen von Erweiterungskarten VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Entfernen des Erweiterungskarten-Risers 1 VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-16.
Installieren von Erweiterungskarten-Riser 1 VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
3 Entfernen Sie gegebenenfalls die Erweiterungskarte aus dem Erweiterungssteckplatz. Siehe „Entfernen von Erweiterungskarten“ auf Seite 124. 4 Um den Erweiterungskarten-Riser zu entfernen, heben Sie den Erweiterungskarten-Riser vom Anschluss auf der Systemplatine ab. Siehe Abbildung 3-17. Abbildung 3-17.
Installieren von Erweiterungskarten-Riser 2 VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Entfernen der integrierten Speichercontrollerkarte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-18.
Installieren der integrierten Speichercontrollerkarte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
10 Setzen Sie die Lüfterbaugruppe ein. Siehe „Installieren der Lüfterbaugruppe“ auf Seite 116. 11 Setzen Sie das Kühlgehäuse wieder ein. Siehe „Installieren des Kühlgehäuses“ auf Seite 104. 12 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 13 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
Abbildung 3-19. RAID-Akku entfernen und installieren 1 2 3 4 5 1 RAID-Akkuhalter 2 RAID-Akku 3 RAID-Akkukabel 4 Schlitz im RAID-Akkuträger 5 Kühlgehäuse Installieren des RAID-Akkus VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
4 Verbinden Sie das Akkukabel mit dem Anschluss auf der integrierten Speichercontrollerkarte. 5 Setzen Sie die Lüfterbaugruppe ein. Siehe „Installieren der Lüfterbaugruppe“ auf Seite 116. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 7 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
8 Verbinden Sie das System und die angeschlossenen Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein. Abbildung 3-20.
Installieren einer iDRAC6 Enterprise-Karte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
vFlash-Medium (optional) Die vFlash-Medienkarte ist eine SD-Karte (Secure Digital), die an der optionalen iDRAC6 Enterprise-Karte in der hinteren Ecke des Systems eingesetzt wird. Entfernen einer vFlash-Medienkarte Um das vFlash-Medium zu entfernen, drücken Sie die Karte nach innen, um sie freizugeben und ziehen Sie dann die Karte aus dem Steckplatz. Installieren einer vFlash-Medienkarte 1 Lokalisieren Sie den vFlash-Mediensteckplatz in der hinteren Ecke des Systems. Siehe Abbildung 1-3.
2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 90. 3 Entfernen Sie gegebenenfalls die SD-Karten vom internen zweifachen SD-Modul. Siehe Abbildung 3-1. 4 Trennen Sie das Kabel vom internen zweifachen SD-Modul. Siehe Abbildung 3-21. 5 Heben Sie die Sperrklinke an, die das interne zweifache SD-Modul an der vorderen Gehäusebaugruppe sichert, und heben Sie das Modul aus der Baugruppe. Siehe Abbildung 3-21. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91.
Installieren des internen zweifachen SD-Moduls VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Prozessoren Entfernen eines Prozessors VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-22. Kühlkörper entfernen und installieren 1 2 1 Kühlkörper 2 Aussparung auf Systemplatine VORSICHTSHINWEIS: Der Prozessor steht im Sockel unter starker mechanischer Spannung. Beachten Sie, dass der Freigabehebel plötzlich hochschnellen kann, wenn er nicht festgehalten wird.
8 Halten Sie Ihren Daumen fest auf dem Freigabehebel des Prozessorsockels und lösen Sie den Hebel aus der verriegelten Position, indem Sie ihn nach unten drücken und unter der Lasche hervorziehen. Schwenken Sie den Freigabehebel um 90 Grad nach oben, bis der Prozessor vom Sockel gelöst ist. Siehe Abbildung 3-23. 9 Drehen Sie die Prozessorabdeckung nach oben und zur Seite. Siehe Abbildung 3-23. Abbildung 3-23.
Abbildung 3-24. Prozessorplatzhalter entfernen und installieren 2 1 1 Entriegelungshebel 2 Prozessorplatzhalter VORSICHTSHINWEIS: Achten Sie darauf, keine Kontaktstifte am ZIF-Sockel zu verbiegen, wenn Sie den Prozessor entfernen. Durch ein Verbiegen der Kontaktstifte kann die Systemplatine dauerhaft beschädigt werden. 10 Heben Sie den Prozessor vorsichtig aus dem Sockel und belassen Sie den Hebel in senkrechter Position, damit der neue Prozessor in den Sockel eingepasst werden kann.
Installieren eines Prozessors VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
6 Richten Sie die Kerben am Prozessor mit den Passungen am ZIF-Sockel aus. Siehe Abbildung 3-23. 7 Setzen Sie den Prozessor in den Sockel ein. Halten Sie den Prozessor gerade (siehe Abbildung 3-23) und setzen Sie ihn gerade nach unten in den Socke l.Der Prozessor sollte auf den Stiften beweglich sein und durch die Prozessorabdeckung an seiner Position gehalten werden. 8 Überprüfen Sie, ob der Prozessor richtig ausgerichtet und eingesetzt ist. 9 Schließen Sie die Prozessorabdeckung. Siehe Abbildung 3-23.
18 Drücken Sie , um das System-Setup-Programm aufzurufen und überprüfen Sie, ob die Prozessorinformationen mit der neuen Systemkonfiguration übereinstimmen. Siehe „Aufrufen des System-SetupProgramms“ auf Seite 64. 19 Führen Sie die Systemdiagnose aus, um sicherzustellen, dass der neue Prozessor korrekt funktioniert. Informationen zum Ausführen der Diagnose finden Sie unter „Ausführen der integrierten Systemdiagnose“ auf Seite 190.
Abbildung 3-25. Systembatterie austauschen 2 1 3 1 Positive Seite des Batteriesockels 3 Negative Seite des Batteriesockels 2 Systembatterie 3 Lokalisieren Sie den Batteriesockel. Siehe Abbildung 6-1. 4 Entfernen Sie gegebenenfalls die integrierte Speichercontrollerkarte. Siehe „Entfernen der integrierten Speichercontrollerkarte“ auf Seite 130.
7 Wenn Sie eine neue Systembatterie installieren, unterstützen Sie den Batteriesockel, indem Sie fest auf die positive Seite des Sockels drücken. 8 Halten Sie die Batterie mit dem Pluspol (+) nach oben und schieben Sie sie unter die Haltklammern auf der Plus-Seite des Sockels. 9 Drücken Sie die Batterie gerade nach unten in den Sockel, bis sie einrastet. 10 Setzen Sie gegebenenfalls die integrierte Speichercontrollerkarte ein. „Installieren der integrierten Speichercontrollerkarte“ auf Seite 132.
SAS-Rückwandplatine Entfernen der SAS-Rückwandplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-26.
Installieren der SAS-Rückwandplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Stromverteilungsplatine Entfernen der Stromverteilungsplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-27.
Installation der Stromverteilungsplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Bedienfeldbaugruppe Entfernen des Bedienfeldanzeigemoduls VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Installieren des Bedienfeldanzeigemoduls VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-28.
Entfernen der Bedienfeldplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Installieren der Bedienfeldplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Systemplatinenbaugruppe Die Systemplatine ist in zwei Platinen unterteilt, die durch eine Hochleistungsverbindung miteinander verbunden sind. • Prozessorplatine – hier befinden sich die Anschlüsse für die Speichermodule, die Netzteile und Prozessoren. • E/A-Platine – hier befinden sich die Anschlüsse für die Erweiterungskarten-Riser und die Erweiterungskarten.
5 Schieben Sie die vordere Gehäusebaugruppe vom System weg. 6 Entfernen Sie die Kabelklemme. 7 Entfernen Sie die Speichermodule. Siehe „Entfernen von Speichermodulen“ auf Seite 110. 8 Entfernen Sie die Lüfterbaugruppe. Siehe „Entfernen der Lüfterbaugruppe“ auf Seite 114. WARNUNG: Der Kühlkörper ist auch nach dem Ausschalten des Systems eine Zeitlang auf hoher Temperatur. Achten Sie darauf, die Kühlkörper nicht zu berühren, während Sie die E/A-Platine oder die Prozessorplatine entfernen.
VORSICHTSHINWEIS: Fassen Sie die Systemplatinenbaugruppe nicht an einem Speichermodul, einem Prozessor oder anderen Komponenten an. 17 Halten Sie die Prozessorplatine am Griff und an der Kante (siehe Abbildung 3-29). Winkeln Sie die Prozessorplatine zur Systemrückseite hin an und heben Sie die Platine aus dem Gehäuse. 18 Um die E/A-Platine zu entfernen, ziehen Sie den Freigabestift und schieben Sie die E/A-Platine zur Systemvorderseite. Heben Sie die E/APlatine vorsichtig aus dem Gehäuse. Abbildung 3-29.
Installieren der Systemplatinenbaugruppe VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
11 Setzen Sie die Lüfterbaugruppe ein. Siehe „Installieren der Lüfterbaugruppe“ auf Seite 116. 12 Setzen Sie gegebenenfalls den NIC-Hardwareschlüssel auf der E/A-Platine ein. Siehe „Interner NIC-Hardwareschlüssel“ auf Seite 118. 13 Setzen Sie gegebenenfalls die Erweiterungskarten-Riser ein. Siehe „Installieren von Erweiterungskarten-Riser 1“ auf Seite 127 und „Installieren von Erweiterungskarten-Riser 2“ auf Seite 129.
Installieren von Systemkomponenten
Fehlerbehebung beim System Sicherheit geht vor – für Sie und Ihr System VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei externen Verbindungen Stellen Sie sicher, dass alle externen Kabel fest mit den externen Anschlüssen des Systems verbunden sind, bevor Sie mit der Fehlerbehebung von externen Geräten beginnen. Die Anschlüsse auf der Vorder- und Rückseite des Systems sind in Abbildung 1-1 und Abbildung 1-3 dargestellt. Fehlerbehebung beim Grafiksubsystem 1 Überprüfen Sie die Systemanschlüsse und die Stromversorgung des Bildschirms.
c Tauschen Sie die Tastatur/Maus durch eine andere, funktionierende Tastatur/Maus aus. Wenn sich das Problem auf diese Weise lösen lässt, ersetzen Sie die defekte Tastatur/Maus. Wenn das Problem nicht gelöst wurde, fahren Sie mit dem nächsten Schritt fort und beginnen Sie mit der Fehlerbehebung der anderen USB-Geräte am System. 2 Schalten Sie alle angeschlossenen USB-Geräte aus und trennen Sie sie vom System.
Fehlerbehebung bei einem seriellen E/A-Gerät 1 Schalten Sie das System und die an die serielle Schnittstelle angeschlossenen Peripheriegeräte aus. 2 Ersetzen Sie das serielle Schnittstellenkabel durch ein nachweislich funktionierendes Kabel und schalten Sie das System und das serielle Gerät ein. Wenn sich das Problem auf diese Weise lösen lässt, muss das Schnittstellenkabel ersetzt werden. 3 Schalten Sie das System und das serielle Gerät aus und tauschen Sie das Gerät gegen ein vergleichbares Gerät aus.
• Ändern Sie, falls möglich, die Autonegotiationseinstellung. • Verwenden Sie einen anderen Anschluss am Switch bzw. Hub. Wenn eine NIC-Karte an Stelle eines integrierten NIC verwendet wird, lesen Sie die Dokumentation zur NIC-Karte. 4 Stellen Sie sicher, dass die entsprechenden Treiber installiert und die Protokolle eingebunden sind. Weitere Informationen finden Sie in der Dokumentation zum NIC. 5 Rufen Sie das System-Setup-Programm auf und stellen Sie sicher, dass die NIC-Ports aktiviert sind.
3 Bauen Sie Komponenten aus dem System aus. Siehe „Installieren von Systemkomponenten“ auf Seite 87. • Festplattenlaufwerke • Kühlgehäuse • Lüfterbaugruppe • SD-Karten • USB-Speicherstick • NIC-Hardwareschlüssel • Internes zweifaches SD-Modul • Erweiterungskarten und beide Erweiterungskarten-Riser • Integrierter Speichercontroller • iDRAC6 Enterprise-Karte • Netzteile • Prozessoren und Kühlkörper 4 Lassen Sie das System gründlich trocknen (mindestens 24 Stunden).
Fehlerbehebung bei einem beschädigten System VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei der Systembatterie ANMERKUNG: Wenn das System für lange Zeit ausgeschaltet bleibt (für Wochen oder Monate), verliert der NVRAM möglicherweise seine Systemkonfigurationsdaten. Dies wird durch eine erschöpfte Batterie verursacht. 1 Geben Sie die Uhrzeit und das Datum erneut über das System-SetupProgramm ein. Siehe „Verwenden des System-Setup-Programms und des UEFI-Boot-Managers“ auf Seite 63. 2 Schalten Sie das System aus und trennen Sie es für mindestens eine Stunde vom Netzstrom.
Fehlerbehebung bei Netzteilen VORSICHTSHINWEIS: Um das System betreiben zu können, muss mindestens ein Netzteil installiert sein. Wenn das System über einen längeren Zeitraum mit nur einem Netzteil betrieben wird, kann dies eine Überhitzung zur Folge haben. 1 Identifizieren Sie das fehlerhafte Netzteil anhand der Fehleranzeige am Netzteil. Siehe „Anzeigecodes für Stromversorgung“ auf Seite 22. 2 Setzen Sie die Netzteile neu ein, indem Sie sie entfernen und neu installieren.
Stellen Sie sicher, dass keine der folgenden Bedingungen zutrifft: • Systemabdeckung, Kühlgehäuse, Laufwerkplatzhalter, Speichermodulplatzhalter, Netzteilplatzhalter oder PCIe-Abdeckblech wurde entfernt. • Die Umgebungstemperatur ist zu hoch. Die Anforderungen des Systems an die Betriebstemperatur können Sie dem Handbuch zum Einstieg entnehmen. • Der externe Luftstrom ist gestört. • Kabel im Innern des Systems beeinträchtigen den Luftstrom.
4 Wenn das Problem weiterhin besteht, installieren Sie einen neuen Lüfter. Siehe „Entfernen eines Lüfters“ auf Seite 112 und „Installieren eines Lüfters“ auf Seite 114. Wenn der Ersatzlüfter richtig funktioniert, schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. Falls der Ersatzlüfter nicht funktioniert, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203.
4 Rufen Sie das System-Setup-Programm auf, und überprüfen Sie die Einstellung für den Systemspeicher. Siehe „Bildschirm „Memory Settings“ (Speichereinstellungen)“ auf Seite 69. Ändern Sie gegebenenfalls die Einstellungen für den Speicher. Wenn die Speichereinstellungen für den installierten Speicher korrekt sind, aber noch immer ein Problem angezeigt wird, lesen Sie Schritt 14. 5 Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Netzstrom.
17 Um ein nicht bestimmtes defektes Speichermodul zu identifizieren, ersetzen Sie das Speichermodul im ersten DIMM-Sockel durch ein Modul des gleichen Typs und der gleichen Kapazität. Siehe „Installieren von Speichermodulen“ auf Seite 108. 18 Setzen Sie gegebenenfalls das Kühlgehäuse auf. Siehe „Installieren des Kühlgehäuses“ auf Seite 104. 19 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91.
6 Setzen Sie gegebenenfalls das Kühlgehäuse auf. Siehe „Installieren des Kühlgehäuses“ auf Seite 104. 7 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 8 Schalten Sie das System und die angeschlossenen Peripheriegeräte ein und überprüfen Sie, ob der USB-Stick funktioniert. 9 Wenn das Problem nicht gelöst wurde, wiederholen Sie Schritt 2 und Schritt 3. 10 Setzen Sie einen anderen USB-Stick ein, der nachweislich funktioniert. 11 Schließen Sie das System.
VORSICHTSHINWEIS: Wenn im System-Setup-Bildschirm Integrated Devices (Integrierte Geräte) die Option Redundancy (Redundanz) auf Mirror Mode (Spiegelung) gesetzt ist, müssen Sie die Anweisungen von Schritt 5 bis Schritt 9 befolgen, um Datenverlust zu vermeiden. Wenn die Option Redundancy auf Disabled gesetzt ist, fahren Sie fort mit Schritt 10. ANMERKUNG: Wenn ein SD-Kartendefekt auftritt, wird das System vom internen zweifachen SD-Modulcontroller darüber informiert.
Fehlerbehebung bei einem optischen Laufwerk VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei einem Festplattenlaufwerk VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
4 Stellen Sie sicher, dass die erforderlichen Gerätetreiber für die Controllerkarte installiert und korrekt konfiguriert sind. Weitere Informationen finden Sie im Handbuch zum Betriebssystem. 5 Starten Sie das System neu, rufen Sie das System-Setup-Programm auf und überprüfen Sie, ob der Controller aktiviert ist und die Laufwerke im System-Setup-Programm angezeigt werden. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 63.
VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei Erweiterungskarten VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
13 Führen Sie die entsprechende Online-Diagnose durch. Wenn die Tests fehlschlagen, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 203. 14 Führen Sie für jede Erweiterungskarte, die Sie in Schritt 10 entfernt haben, folgende Schritte durch: a Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Netzstrom. b Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 90. c Installieren Sie eine der Erweiterungskarten neu. d Schließen Sie das System.
7 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 91. 8 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und die angeschlossenen Peripheriegeräte ein. 9 Führen Sie die entsprechende Online-Diagnose durch. 10 Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 11 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 90. 12 Entfernen Sie die Lüfterbaugruppe.
Ausführen der Systemdiagnose Bei Problemen mit dem System sollten Sie eine Diagnose durchführen, bevor Sie technische Unterstützung anfordern. Der Zweck der Diagnose ist es, die Hardware des Systems ohne zusätzliche Ausrüstung und ohne das Risiko eines Datenverlusts zu überprüfen. Wenn Sie ein Problem nicht selbst beheben können, können Service- und Supportmitarbeiter die Diagnoseergebnisse zur Lösung des Problems verwenden.
• Laufende Tests bei Auftreten eines Fehlers unterbrechen oder die Tests ganz abbrechen, wenn eine einstellbare Obergrenze für Fehler erreicht wird • Hilfemeldungen mit kurzer Beschreibung aller Tests und ihrer Parameter anzeigen • Statusmeldungen ansehen, die zeigen, ob Tests erfolgreich abgeschlossen wurden • Fehlermeldungen über Probleme während des Testvorgangs anzeigen Einsatzbereich der integrierten Systemdiagnose Wenn eine Hauptkomponente oder ein Gerät des Systems nicht ordnungsgemäß funktio
Testoptionen der Systemdiagnose Klicken Sie auf die Testoption im Fenster Main Menu (Hauptmenü). Testoption Funktion Express Test Führt eine schnelle Überprüfung des Systems durch. Bei dieser Option werden Gerätetests durchgeführt, bei denen keine Eingabe durch den Benutzer erforderlich ist. Extended Test Führt eine genauere Überprüfung des Systems durch. Dieser Test kann eine Stunde oder länger dauern. Custom Test Testet ein bestimmtes Gerät. Information Zeigt Testergebnisse an.
Auswählen von Diagnoseoptionen Die Testoptionen für ein Gerät können Sie im Bereich Diagnostics Options einstellen. • Non-Interactive Tests Only – Führt nur Tests durch, die keine Benutzereingaben erfordern. • Quick Tests Only – Führt nur die schnell durchführbaren Tests am Gerät durch. • Show Ending Timestamp – Schreibt die Zeiten der Tests in die Protokolldatei. • Test Iterations – Legt fest, wie oft der Test durchgeführt wird.
Jumper, Schalter und Anschlüsse Jumper auf der Systemplatine Informationen zum Deaktivieren eines Kennworts finden Sie unter „Deaktivieren eines verlorenen Kennworts“ auf Seite 201. Tabelle 6-1.
Anschlüsse auf der Systemplatine Abbildung 6-1.
Element Anschluss Beschreibung 1 SLOT4_PCIE_G2_X8 PCIe-Steckplatz 4 – x8-Erweiterungssteckplatz 2 SLOT3_PCIE_G2_X8 PCIe-Steckplatz 3 – x8-Erweiterungssteckplatz 3 AMEA CONN Anschluss für iDRAC6 Enterprise-Karte 4 PWRD_EN Jumper zum Aktivieren des Kennworts NVRAM_CLR Jumper zum Löschen des NVRAM 5 MASER CONN Anschluss für iDRAC6-Express-Karte 6 Center PCIE_G2_X8 Anschluss für Erweiterungskarten-Riser 1 7 BATTERY Batteriesockel 8 SATA SATA-Stromversorgungsanschluss 9 FAN6 Anschl
Element 196 Anschluss Beschreibung B8 Speichermodulsockel B8 14 BP_PWR Stromversorgung für Rückwandplatine und USB auf der Vorderseite 15 CPU2 Sockel für Prozessor 2 16 FAN1 Anschluss für Systemlüfter 1 17 FAN2 Anschluss für Systemlüfter 2 18 PDB_CON Anschluss für Stromverteilungsplatine 19 FAN3 Anschluss für Systemlüfter 3 20 FAN4 Anschluss für Systemlüfter 4 21 PWR_CONN Stromversorgungsanschluss 22 CTRL_PNL Anschluss für Bedienfeld 23 Left PCIE_G2_X16 Anschluss für Erwei
Anschlüsse der SAS-Rückwandplatine Abbildung 6-2.
Anschlüsse der Stromverteilungsplatine Abbildung 6-3.
Komponenten der ErweiterungskartenRiserplatine und PCIe-Busse Abbildung 6-4.
Abbildung 6-5.
Deaktivieren eines verlorenen Kennworts Zu den Sicherheitsfunktionen der Systemsoftware gehören ein Systemkennwort und ein Setup-Kennwort. Diese werden ausführlich unter „Verwenden des System-Setup-Programms und des UEFI-Boot-Managers“ auf Seite 63 beschrieben. Der Kennwort-Jumper aktiviert bzw. deaktiviert diese Kennwortfunktionen und löscht alle derzeit benutzten Kennwörter.
8 Setzen Sie die Steckbrücke auf den Kennwort-Jumper. 9 Schließen Sie das System. 10 Verbinden Sie das System und die Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein. 11 Weisen Sie ein neues System- und/oder Setup-Kennwort zu. Wie Sie im System-Setup-Programm ein neues Kennwort festlegen, erfahren Sie im Abschnitt „Zuweisen eines Systemkennworts“ auf Seite 81.
Wie Sie Hilfe bekommen Kontaktaufnahme mit Dell Kunden in den USA können die Nummer 800-WWW-DELL (800-999-3355) anrufen. ANMERKUNG: Wenn Sie nicht mit dem Internet verbunden sind, finden Sie die Kontaktinformationen auf der Rechnung, dem Lieferschein oder im Produktkatalog von Dell. Dell bietet verschiedene Optionen für Support und Service online oder per Telefon. Die Verfügbarkeit ist je nach Land und Produkt unterschiedlich, und bestimmte Dienstleistungen sind in Ihrer Region eventuell nicht erhältlich.
Wie Sie Hilfe bekommen
Stichwortverzeichnis A Akku Fehlerbehebung beim RAID-Kartenakku, 184 Anschlüsse Bildschirm, 12, 19 USB, 12, 19 Anweisungen nur für Service Systemplatine, 161 Anzeigen NIC, 21 Stromversorgung, 12, 22 Vorderseite, 12 Arbeitsspeicher Fehlerbehebung, 177 Beschädigte Systeme Fehlerbehebung, 173 Betriebsanzeigen, 12, 22 Bildschirm Anschlüsse auf der Vorderseite, 12 C CD/DVD-Laufwerk Siehe Optisches Laufwerk CD-Laufwerk Fehlerbehebung, 182 D Austauschen Netzteil, 101 Systembatterie, 147 Dell Kontaktaufnahme,
E Empfohlene Werkzeuge, 87 Entfernen Erweiterungskarte, 124 Festplatten, 94 Festplattenlaufwerk aus einem Laufwerkträger, 96 Frontverkleidung, 89 Laufwerkplatzhalter, 93 Netzteil, 100 Netzteilplatzhalter, 102 Prozessor, 141 SAS-Controller, 130 SAS-Rückwandplatine, 150 Speichermodule, 110 Systemplatine, 161 Entfernen der Prozessorplatine, 161 Erweiterungskarten Entfernen, 124 Fehlerbehebung, 186 Installieren, 122 SAS-Controller, 130 Erweiterungssteckplätze, 120 F Fehlerbehebung Arbeitsspeicher, 177 Batterie
G K Garantie, 61 Kennwort Deaktivieren, 201 Setup, 83 System, 80 Gehäuseeingriffschalter, 200 Grafik Fehlerbehebung, 168 Kontaktaufnahme mit Dell, 203 Kühlkörper, 142 H Hot-plug Festplattenlaufwerke, 92 L I Laufwerkplatzhalter Entfernen, 93 Installieren, 94 iDRAC-Karte Installieren, 135 Laufwerkträger Festplattenlaufwerk, 96 iDRAC-Konfigurationsprogramm, 85 LCD-Display Menüs, 16 Merkmale, 14 Installation Netzteilplatzhalter, 102 Installieren Erweiterungskarte, 122 Festplattenlaufwerke, 95 Fron
Mikroprozessoren Fehlerbehebung, 187 Siehe Prozessor.
Sicherheit, 167 Speichermodule (DIMMs) Entfernen, 110 Installieren, 108 Konfigurieren, 105 Speicherstickanschluss (USB), 116 Start Zugriff auf Systemfunktionen, 11 Steckplätze Siehe Erweiterungssteckplätze Support Kontaktaufnahme mit Dell, 203 System-Setup-Programm (fortgesetzt) Optionen für integrierte Geräte, 72 Optionen für serielle Kommunikation, 74 PCI-IRQ-Zuweisungen, 73 Prozessoreinstellungen, 69 SATA-Einstellungen, 71 Speichereinstellungen, 69 Starteinstellungen, 71 Tastenbefehl, 64 Systemstartprob
USB Anschlüsse auf der Vorderseite, 12 Interner Anschluss für Speicherstick, 116 USB-Stick Fehlerbehebung, 179-180 V Verkabelung Optisches Laufwerk, 97 W Warnmeldungen, 60 210 Stichwortverzeichnis