Dell™ PowerEdge™ R810 Systems Getting Started With Your System Guide de mise en route Primeiros passos com o sistema Procedimientos iniciales con el sistema
Dell™ PowerEdge™ R810 Systems Getting Started With Your System Regulatory Model E05S Series
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved.
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. Unpacking the System Unpack your system and identify each item. Installing the Rails and System in a Rack Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your system.
Optional – Connecting the Keyboard, Mouse, and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws (if any) on the monitor's cable connector. Connecting the Power Cable(s) Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor.
Securing the Power Cable(s) Attach the power cable retention bracket on the right bend of the power supply handle. Bend the system power cable into a loop as shown in the illustration and attach to the bracket’s cable clasp. Plug the other end of the power cable into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Turning On the System Press the power button on the system and the monitor.
Installing the Optional Bezel Install the bezel (optional). Complete the Operating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system.
• Microsoft Windows Server 2008 Standard, Enterprise, and Datacenter (x64) Editions (with Hyper-V role enabled) • Microsoft Windows Server 2003 Standard and Enterprise (x86) Editions • Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions • Microsoft Windows Server 2003 R2 Standard and Enterprise (x86) Editions with SP2 • Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacenter (x64) Editions with SP2 • Microsoft Windows Essential Business Server 2008 Standard and Prem
Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document. • The rack documentation included with your rack solution describes how to install your system into a rack. • The Hardware Owner’s Manual provides information about system features and describes how to troubleshoot the system and install or replace system components.
Technical Specifications Processor Processor type Up to four Intel® Xeon® 7500 series processors (up to eight core processors) Or Up to four Intel Xeon 6500 series processors (up to eight core processors) Expansion Bus Bus type PCI Express Generation 2 Expansion slots Riser 1 Slot 1: x8 link with x16 physical connector, 9.
Drives Hard drives Up to six 2.5-inch, internal hot-swappable SAS, SATA, or SSD drives Diskette drive Optional external USB 1.44 MB Optical drive One optional slimline SATA DVD-ROM or DVD+RW drive NOTE: DVD devices are data only.
Video Video type Integrated Matrox G200 with iDRAC6 Video memory 8 MB (shared with iDRAC application memory) Power AC power supply Wattage (per power supply) 1100 W Voltage (per power supply) 100–240 V, 50/60 Hz, auto-ranging System heat dissipation 4012 BTU/Hr Maximum inrush current (per power supply) Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less Batteries System battery CR 2032 3.
Environmental NOTE: For additional information about environmental measurements for specific system configurations, see www.dell.com/environmental_datasheets. Temperature Operating 10° to 35°C (50° to 95°F) with a maximum temperature gradation of 10°C per hour NOTE: For altitudes above 2950 feet, the maximum operating temperature is derated 1ºF/550 ft.
Environmental (continued) Altitude Operating –16 to 3048 m (–50 to 10,000 ft) NOTE: For altitudes above 2950 feet, the maximum operating temperature is derated 1ºF/550 ft. Storage –16 to 10,600 m (–50 to 35,000 ft) Airborne Contaminant Level Class G2 or lower as defined by ISA-S71.
14 Getting Started With Your System
Systèmes Dell™ PowerEdge™ R810 Guide de mise en route Modèle réglementaire série E05S
Remarques, précautions et avertissements REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : une PRÉCAUTION vous avertit d'un risque d'endommagement du matériel ou de perte de données en cas de non-respect des instructions données. AVERTISSEMENT : un AVERTISSEMENT vous avertit d’un risque d'endommagement du matériel, de blessure corporelle ou de mort.
Installation et configuration AVERTISSEMENT : avant de suivre la procédure suivante, lisez les consignes de sécurité fournies avec le système. Déballage du système Sortez le système de son emballage et identifiez chaque élément. Installation des rails et du système dans un rack Assemblez les rails et installez le système dans le rack en suivant les consignes de sécurité et les instructions d'installation du rack fournies avec votre système.
Facultatif – Connexion du clavier, de la souris et du moniteur Connectez le clavier, la souris et le moniteur (si nécessaire). Les icônes des connecteurs situées à l'arrière du système indiquent où insérer chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble du moniteur, s'il en est équipé. Branchement du ou des câbles d'alimentation Branchez le ou les câbles d'alimentation au système et, si vous utilisez un moniteur, connectez son câble d'alimentation à celui-ci.
Fixation du ou des câbles d'alimentation Fixez le support de fixation du câble sur la partie droite de la poignée du bloc d'alimentation. Faites une boucle comme indiqué dans l'illustration et insérez le câble d'alimentation dans le clip du support. Branchez ensuite l'autre extrémité du câble d'alimentation sur une prise secteur mise à la terre ou sur une source d'alimentation autonome (onduleur ou unité de distribution de l'alimentation).
Installation du cadre en option Installez le cadre (si nécessaire). Fin de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez tout d'abord la documentation associée, fournie avec l'ordinateur. Pour une première installation du système d'exploitation, consultez la documentation relative à l'installation et à la configuration du système d'exploitation.
Systèmes d'exploitation pris en charge • Microsoft® Windows Server® 2008 R2, Éditions Standard, Enterprise, et Datacenter (x64) • Microsoft Windows Server 2008, Éditions Standard et Enterprise (x86) avec SP2 • Microsoft Windows Server 2008, Éditions Standard, Enterprise et DataCenter (x64) avec SP2 • Microsoft Windows Server 2008, Éditions Standard et Enterprise (x86) • Microsoft Windows Server 2008, Éditions Standard, Enterprise et Datacenter (x64) avec rôle Hyper-V activé • Microsoft Windows Se
Autres informations utiles AVERTISSEMENT : reportez-vous aux informations sur la sécurité et les réglementations fournies avec votre système. Les informations sur la garantie se trouvent dans ce document ou dans un document distinct. • La documentation fournie avec le rack indique comment installer le système dans un rack.
Caractéristiques techniques Processeur Type de processeur Jusqu'à quatre processeurs Intel® Xeon® série 7500 (processeurs à huit cœurs disponibles) ou Jusqu'à quatre processeurs Intel Xeon série 6500 (processeurs à huit cœurs disponibles) Bus d'extension Type de bus PCI Express 2ème génération Logements d'extension Carte de montage 1 Logement 1 : liaison x8 avec connecteur physique en x16, longueur de 9,5 pouces, hauteur standard Logement 2 : liaison x4 avec connecteur physique en x8, mi-hauteur, avec
Mémoire Architecture Modules DIMM ECC DDR3 enregistrés cadencés à 1066 MHz Connecteurs de barrettes de mémoire 32 connecteurs à 240 broches Capacité des barrettes de mémoire RDIMM de 1 Go, 2 Go, 4 Go, 8 Go ou 16 Go (barrettes à simple, double ou quadruple rangée selon la capacité) RAM minimale 4 Go (par processeur) REMARQUE : il est recommandé d'installer 16 Go au minimum pour exécuter les applications.
Connecteurs Arrière NIC Quatre connecteurs RJ-45 (pour cartes réseau de 1 Go intégrées) Carte réseau (carte de gestion) Un port de carte réseau de gestion (en option) sur une carte iDRAC6 Enterprise Série Un connecteur DTE à 9 broches, compatible 16550 USB Quatre connecteurs à 4 broches, compatibles USB 2.
Alimentation Bloc d'alimentation en CA Puissance (par bloc d'alimentation) 1100 W Tension (par bloc d'alimentation) 100–240 V, 50/60 Hz, plages automatiques Dissipation thermique du système 4012 BTU/h Courant d'appel maximum (par bloc d'alimentation) Dans des conditions de ligne typiques et dans toute la gamme ambiante de fonctionnement du système, le courant d'appel peut atteindre 55 A par bloc d'alimentation pendant un maximum de 10 ms.
Environnement REMARQUE : pour plus d'informations concernant les mesures environnementales liées à différentes configurations spécifiques, voir www.dell.com/environmental_datasheets. Température En fonctionnement De 10 à 35 °C (de 50 à 95 °F) avec un gradient thermique maximal de 10 °C par heure REMARQUE : pour les altitudes supérieures à 900 mètres (2 950 pieds), la température maximale de fonctionnement est réduite de 1 °C tous les 300 mètres (1 °F tous les 550 pieds).
Environnement (Suite) Altitude En fonctionnement De -16 à 3 048 m (de -50 à 10 000 pieds) REMARQUE : pour les altitudes supérieures à 900 mètres (2 950 pieds), la température maximale de fonctionnement est réduite de 1 °C tous les 300 mètres (1 °F tous les 550 pieds). Stockage De -16 à 10 600 m (-50 à 35 000 pieds) Contaminants en suspension dans l'air Classe 28 G2 ou inférieure selon la norme ISA-S71.
Sistemas Dell™ PowerEdge™ R810 Primeiros passos com o sistema Modelo de Regulamentação Série E05S
Notas, Avisos e Advertências NOTA: Uma NOTA fornece informações importantes que o ajudam a usar melhor o computador. AVISO: Uma ADVERTÊNCIA indica um potencial de danos ao hardware ou de perda de dados caso as instruções não sejam seguidas. ADVERTÊNCIA: Uma ADVERTÊNCIA indica um potencial de danos à propriedade, de lesões corporais ou mesmo de morte. ____________________ As informações deste documento estão sujeitas a alteração sem aviso prévio. © 2009 Dell Inc. Todos os direitos reservados.
Instalação e configuração ADVERTÊNCIA: Antes de executar este procedimento, siga as instruções de segurança fornecidas com o sistema. Como remover o sistema da embalagem Remova o sistema da embalagem e identifique cada item. Como instalar os trilhos e o sistema no rack Monte os trilhos e instale o sistema no rack seguindo as instruções de segurança e as instruções de instalação fornecidas com o sistema.
Opcional – Como conectar teclado, mouse e monitor Conecte o teclado, o mouse e o monitor (opcional). Os conectores na parte traseira do sistema têm ícones que indicam quais cabos devem ser ligados a cada conector. Certifique-se de apertar os parafusos (se houver algum) no conector do cabo do monitor. Como conectar cabo(s) de alimentação Conecte o(s) cabo(s) de alimentação ao sistema e, se for usado um monitor, conecte o(s) cabo(s) de alimentação ao monitor.
Como prender o(s) cabo(s) de alimentação Conecte o suporte de retenção do cabo de alimentação na dobra direita da alça da fonte de alimentação. Curve o cabo de alimentação, conforme mostrado na ilustração e prenda-o ao gancho localizado no suporte.
Instalação do painel frontal Instale o painel frontal (opcional). Conclua a instalação do sistema operacional Caso tenha adquirido um sistema operacional pré-instalado, consulte a respectiva documentação fornecida com o sistema. Para instalar um sistema operacional pela primeira vez, consulte a documentação de instalação e configuração do sistema operacional.
Sistemas operacionais compatíveis • Microsoft® Windows Server® 2008 R2 edições Standard, Enterprise e Datacenter (x64) • Microsoft Windows Server 2008, edições Standard e Enterprise (x86) com SP2 • Microsoft Windows Server 2008, edições Standard, Enterprise e Datacenter com SP2 (x64) • Microsoft Windows Server 2008, edições Standard e Enterprise (x86) • Microsoft Windows Server 2008, edições Standard, Enterprise e Datacenter (x64) com a função Hyper-V ativada • Microsoft Windows Server 2003, ediç
Outras informações úteis ADVERTÊNCIA: Consulte as informações de regulamentação e de segurança fornecidas com o sistema. As informações sobre garantia podem estar incluídas neste documento ou serem fornecidas em um documento separado. • A documentação do rack incluída descreve como instalar o sistema em racks. • O Manual do proprietário de hardware fornece informações sobre os recursos do sistema e descreve como solucionar problemas do sistema e instalar ou trocar componentes.
Especificações técnicas Processador Tipo de processador Até quatro processadores Intel® Xeon® da série 7500 (até 8 processadores de núcleo) Ou Até quatro processadores Intel Xeon da série 6500 (até 8 processadores de núcleo) Barramento de expansão Tipo de barramento PCI Express Geração 2 Slots de expansão Riser 1 Slot 1: link x8 com conector físico x16, 9,5 pol de comprimento e altura padrão Slot 2: link x4 com coonector físico x8, perfil baixo, com suporte de altura padrão Placa de sistema Slot 3: lin
Memória Arquitetura DIMMs ECC registradas DDR3 de 1066 MHz Soquetes dos módulos de memória Trinta e dois de 240 pinos. Capacidades dos módulos de memória RDIMMS de 1 GB, 2 GB, 4 GB, 8 GB ou 16 GB (posição única, dupla ou quádrupla, dependendo da capacidade) Mínimo de RAM 4 GB (por processador) NOTA: Recomenda-se que você instale um mínimo de 16 GB para executar os aplicativos.
Conectores Traseiros Placa de rede Quatro conectores RJ-45 (para placas de rede de 1 GB integradas) NIC (NIC de gerenciamento) Uma porta opcional de NIC de gerencamento na placa iDRAC6 Enterprise Serial DTE de 9 pinos, compatível com 16550 USB Quatro conectores de 4 pinos, compatível com USB 2.0 Vídeo VGA de 15 pinos vFlash Um slot de placa de memória vFlash na placa iDRAC6 Enterprise Frontais Vídeo VGA de 15 pinos USB Dois conectores de 4 pinos, compatíveis com USB 2.
Alimentação Fonte de alimentação CA Potência (por fonte de alimentação) 1100 W Voltagem (por fonte de alimentação) 100–240 V, 50/60 Hz, alcance automático Dissipação de calor do sistema 4012 BTU/h Corrente de entrada máxima (por fonte de alimentação) Sob condições de linha típicas e em todo o intervalo de temperatura ambiente de operação do sistema, a corrente de entrada pode atingir 55 A por fonte de alimentação por 10 ms ou menos.
Ambientais NOTA: Para obter informações adicionais sobre as medições ambientais para configurações de sistema específicas, visite o site www.dell.com/environmental_datasheets (em inglês). Temperatura Operacional 10° a 35° C com variação máxima de 10° C por hora NOTA: Para altitudes acima de 900 m, a temperatura máxima de operação diminui à razão de 1 °C/ 300 m.
Ambientais (continuação) Altitude Operacional –16 m a 3.048 m NOTA: Para altitudes acima de 900 m, a temperatura máxima de operação diminui à razão de 1° C / 300 m Armazenamento –16 m a 10.600 m Nível de poluentes transportados pelo ar Classe 42 G2 ou inferior, conforme definido pela norma ISA-S71.
Sistemas Dell™ PowerEdge™ R810 Procedimientos iniciales con el sistema Modelo reglamentario serie E05S
Notas, precauciones y avisos NOTA: Una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. PRECAUCIÓN: Un mensaje de PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos si no se siguen las instrucciones. AVISO: Un mensaje de AVISO indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin previo aviso. © 2009 Dell Inc. Todos los derechos reservados.
Instalación y configuración AVISO: Antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. Desembalaje del sistema Desembale el sistema e identifique cada elemento. Instalación de los rieles y del sistema en un rack Monte los rieles e instale el sistema en el rack siguiendo las instrucciones de seguridad y de instalación del rack incluidas con el sistema.
Conexión del teclado, el ratón y el monitor (opcional) Conecte el teclado, el ratón y el monitor (opcional). Los conectores de la parte posterior del sistema incluyen iconos que indican qué cable debe enchufarse en cada conector. Asegúrese de apretar los tornillos (si los hay) del conector del cable del monitor. Conexión de los cables de alimentación Conecte los cables de alimentación al sistema y, si se utiliza un monitor, conecte el cable de alimentación correspondiente al monitor.
Fijación de los cables de alimentación Fije el soporte de retención del cable de alimentación en el codo derecho del asa de la fuente de alimentación. Doble el cable de alimentación del sistema en forma de bucle, como se muestra en la ilustración, y fíjelo a la abrazadera correspondiente del soporte.
Encendido del sistema Presione el botón de encendido del sistema y del monitor. Los indicadores de alimentación deberían encenderse. Instalación del embellecedor opcional Instale el embellecedor (opcional).
Instalación del sistema operativo Si ha adquirido un sistema operativo preinstalado, consulte la documentación del sistema operativo que se suministra con el sistema. Para instalar un sistema operativo por primera vez, consulte la documentación de instalación y configuración del sistema operativo. Asegúrese de que el sistema operativo esté instalado antes de instalar hardware o software no adquiridos con el sistema.
• Microsoft Windows Server 2008 Hyper-V™ • Microsoft Windows Server 2008 R2 Hyper-V • Microsoft Hyper-V Server 2008 R2 • SUSE® Linux Enterprise Server 11 (x86_64) • SUSE Linux Enterprise Server 10 (x86_64) con SP3 • Solaris® 10 10/9 (x86_64) (cuando esté disponible) • VMware® ESX versión 4.0 actualización 1 • VMware ESXi versión 4.0 actualización 1 • Citrix® XenServer™ 5.
Obtención de asistencia técnica Si no comprende alguno de los procedimientos descritos en esta guía o si el sistema no funciona del modo esperado, consulte el Manual del propietario del hardware. Dell™ cuenta con una amplia oferta de formación y certificación de hardware. Para obtener más información, vaya a dell.com/training. Es posible que este servicio no se ofrezca en todas las regiones.
Especificaciones técnicas Procesador Tipo de procesador Hasta cuatro procesadores Intel® Xeon® serie 7500 (procesadores de hasta ocho núcleos) O bien: Hasta cuatro procesadores Intel Xeon serie 6500 (procesadores de hasta ocho núcleos) Bus de expansión Tipo de bus PCI Express de segunda generación Ranuras de expansión Tarjeta vertical 1 Ranura 1: enlace x8 con conector físico x16 de 9,5 pulgadas de longitud y de altura estándar Ranura 2: enlace x4 con conector físico x8 de perfil bajo con un soporte de
Memoria Arquitectura Módulos DIMM DDR3 ECC registrados a 1 066 MHz Zócalos de módulo de memoria 32 de 240 patas Capacidades del módulo de memoria RDIMM de 1 GB, 2 GB, 4 GB, 8 GB o 16 GB (simples, duales o cuádruples, según la capacidad) RAM mínima 4 GB (por procesador) NOTA: Se recomienda instalar un mínimo de 16 GB para ejecutar las aplicaciones.
Conectores Posteriores NIC Cuatro RJ-45 (para NIC de 1 GB integradas) NIC (NIC de administración) Un puerto NIC de administración opcional en la tarjeta iDRAC6 Enterprise Serie 9 patas, DTE, compatible con 16550 USB Cuatro de 4 patas compatibles con USB 2.0 Vídeo VGA de 15 patas vFlash Una ranura para tarjeta de memoria vFlash opcional en la tarjeta iDRAC6 Enterprise Frontales Vídeo VGA de 15 patas USB Dos de 4 patas compatibles con USB 2.0 Internos USB Uno de 4 patas compatible con USB 2.
Alimentación Fuente de alimentación de CA Potencia (por fuente de alimentación) 1 100 W Voltaje (por fuente de alimentación) 100–240 V, 50/60 Hz, autoajustable Disipación de calor del sistema 4 012 BTU/h (1 175 W) Corriente de conexión máxima (por fuente de alimentación) En condiciones normales de línea y en todo el rango operativo del sistema, la corriente de la conexión puede alcanzar 55 A por cada fuente de alimentación durante 10 ms o menos.
Especificaciones ambientales NOTA: Para obtener información adicional sobre medidas ambientales relativas a configuraciones del sistema específicas, vaya a www.dell.com/environmental_datasheets. Temperatura En funcionamiento De 10 °C a 35 °C con una gradación de temperatura máxima de 10 °C por hora NOTA: Para altitudes superiores a 900 m, la temperatura máxima de funcionamiento se reduce 1 °C cada 300 m.
Especificaciones ambientales (continuación) Altitud En funcionamiento De –16 a 3 048 m NOTA: Para altitudes superiores a 900 m, la temperatura máxima de funcionamiento se reduce 1 °C cada 300 m. En almacenamiento De –16 a 10 600 m Nivel de contaminación atmosférica Clase G2 o menos de acuerdo con ISA-S71.
58 Procedimientos iniciales con el sistema