Dell™ PowerEdge™ R810 HardwareBenutzerhandbuch Genormtes Modell: E05S Genormter Typ: E05S001
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie das System besser einsetzen können. VORSICHTSHINWEIS: Ein VORSICHTSHINWEIS macht aufmerksam auf mögliche Beschädigung der Hardware oder Verlust von Daten bei Nichtbefolgung von Anweisungen. WARNUNG: Durch eine WARNUNG werden Sie auf Gefahrenquellen hingewiesen, die materielle Schäden, Verletzungen oder sogar den Tod von Personen zur Folge haben können.
Inhalt 1 Wissenswertes zum System . . . . . . . . . . Zugriff auf Funktionen beim Systemstart . . . . . . . . Merkmale und Anzeigen auf der Vorderseite . 13 . . . . . 14 . . . . . . . . . . . . 18 . . . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . . . . 20 Merkmale des LCD-Bedienfelds Home-Bildschirm . Menü Setup . 13 Menü View (Anzeige) . . . . . . . . . . . . . . . . 21 Festplattenanzeigemuster . . . . . . . . . . . . . . . .
Alarmmeldungen . . . . . . . . . . . . . . . . . . . . . Weitere nützliche Informationen 2 . . . . . . . . . . . . Verwenden des System-Setup-Programms und des UEFI-Boot-Managers . Auswahl des Systemstartmodus . 71 . . . . . . . . . . . . 71 Reaktion auf Fehlermeldungen . . . . . . . . . 72 . . . . . . . . . . 72 Verwenden der Steuertasten des System-Setup-Programms . . . . . . . . . . . . . 74 . . . . . . . . . . . . . . . . . . 74 Bildschirm Memory Settings (Speichereinstellungen) . .
Aufrufen des UEFI-Boot-Managers . . . . . . . . . . . Verwenden der Navigationstasten des UEFI-Boot-Managers . . . . . . . . . . . . . 88 . . . . . . . . . . 88 . . . . . . . . . . . 89 . . . . . . . . . . . . 89 Bildschirm UEFI Boot Manager. Bildschirm UEFI Boot Settings Bildschirm System Utilities (Systemdienstprogramme) . System- und Setup-Kennwortfunktionen . . . . . . . . 90 Verwenden des Systemkennworts . . . . . . . . . 90 . . . . . . . . . 93 . . . . . . . . . . . . .
Entfernen einer Festplatte aus einem Laufwerkträger . . . . . . . . . . . . . . 106 . . . . . . . . . . . 107 . . . . . . . . . . . . . . . . . . 107 Installieren einer Festplatte im Laufwerkträger . . . . . Optisches Laufwerk Entfernen eines optischen Laufwerks . . . . . . Netzteile 110 . . . . . . . . . . . . . . . . . . . . . . . . 111 Entfernen eines Netzteils . . . . . . . . . . . . . 111 Installieren eines Netzteils . . . . . . . . . . . . 113 Entfernen des Netzteilplatzhalters .
Interner NIC-Hardwareschlüssel . . . . . . . . . . . . . . 134 . . . . . . . . . . . 134 Erweiterungskarten und Erweiterungskarten-Riser Richtlinien zur Installation von Erweiterungskarten . . . . . . . . . . . . . 136 . . . . . . . . 138 . . . . . . . . . . . . . . . 139 Installieren einer Erweiterungskarte . Entfernen von Erweiterungskarten . Erweiterungskarten-Riser . Entfernen des Erweiterungskarten-Risers 1 . . . . Entfernen des Erweiterungskarten-Risers 2 141 . . . . 141 . . .
Prozessoren . . . . . . . . . . . . . . . . . . . . . . Entfernen eines Prozessors. . . . . . . . . . . . 159 . . . . . . . . . . . . . . . . . . . 162 . . . . . . . 163 . . . . . . . . 165 . . . . . . . . . . . . . . . . . . . . . 166 Installieren einer FlexMem-Brücke. Entfernen einer FlexMem-Brücke Systembatterie Austauschen der Systembatterie . SAS-Rückwandplatine . . . . . . . . . 166 . . . . . . . . . . . . . . . . 168 Entfernen der SAS-Rückwandplatine . . . . . .
Fehlerbehebung beim Grafiksubsystem . Fehlerbehebung bei einem USB-Gerät . . . . . . . . 186 . . . . . . . . . 186 Fehlerbehebung bei einem seriellen E/A-Gerät Fehlerbehebung bei einem NIC . . . . 188 . . . . . . . . . . . . . 188 Fehlerbehebung bei Feuchtigkeit im System . . . . . . Fehlerbehebung bei einem beschädigten System . . . 190 . . . . . . . . 191 . . . . . . . . . . . . .
5 Ausführen der Systemdiagnose . Verwenden von Online Diagnostics . . . . . . . 207 . . . . . . . . . 207 Funktionen der integrierten Systemdiagnose . . . . . Einsatzbereich der integrierten Systemdiagnose . . . 208 . . . . . 208 . . . . . . . . . . 209 Ausführen der integrierten Systemdiagnose Testoptionen der Systemdiagnose . Verwenden der benutzerdefinierten Testoptionen . . 209 . . . . . . 209 . . . . . . . 210 Auswählen von Geräten für den Test . Auswählen von Diagnoseoptionen .
7 Wie Sie Hilfe bekommen Kontaktaufnahme mit Dell . Stichwortverzeichnis . . . . . . . . . . . . 221 221 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhalt
Wissenswertes zum System Zugriff auf Funktionen beim Systemstart Mit den folgenden Tastenkombinationen erhalten Sie beim Startvorgang Zugriff auf Systemfunktionen. Tastenkombination Beschreibung Aufruf des System-Setup-Programms. Siehe „Verwenden des System-Setup-Programms und des UEFI-Boot-Managers“ auf Seite 71. Aufruf von System Services, von wo aus der Lifecycle-Controller geöffnet wird. Über den Lifecycle-Controller haben Sie Zugriff auf Dienstprogramme wie die integrierte Systemdiagnose.
Tastenkombination Beschreibung Aufruf des PERC-Konfigurationsprogramms. Weitere Informationen finden Sie in der Dokumentation zur PERC-Karte auf der Dell Support-Website unter support.dell.com/manuals. Aufruf des Programms zur Konfiguration der NIC-Einstellungen für den PXE-Start. Weitere Informationen finden Sie in der Dokumentation zum integrierten NIC auf der Dell SupportWebsite unter support.dell.com/manuals. Merkmale und Anzeigen auf der Vorderseite Abbildung 1-1.
Element Anzeige, Taste oder Anschluss 1 Betriebsanzeige, Netzschalter Symbol Beschreibung Die Betriebsanzeige leuchtet, wenn das System eingeschaltet ist. Über den Netzschalter wird die Gleichstromversorgung des Systems gesteuert. Bei installierter Frontverkleidung ist der Netzschalter nicht zugänglich. ANMERKUNG: Beim Einschalten des Systems kann es je nach Größe des installierten Speichers zwischen wenigen Sekunden und bis zu zwei Minuten dauern, bis auf dem Bildschirm etwas angezeigt wird.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 4 Bildschirmanschluss Zum Anschließen eines Bildschirms an das System. 5 Systemidentifikationseinschub Ein herausziehbares Feld für Systeminformationen wie ExpressServicenummer, MAC-Adresse des integrierten NICs und MAC-Adresse der iDRAC6 Enterprise-Karte. Platz für ein weiteres Etikett ist vorhanden. 6 LCD-Menütasten Zur Steuerung des LCDBedienfeldmenüs. 7 LCD-Display Zeigt System-ID, Statusinformationen und Systemfehlermeldungen an.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 8 Systemidentifikationstaste Die Identifikationstasten auf der Vorder- und Rückseite dienen dazu, ein bestimmtes System innerhalb eines Racks zu lokalisieren. Wird eine dieser Tasten gedrückt, blinken das LCDDisplay auf der Vorderseite und die blaue Systemstatusanzeige auf der Rückseite, bis eine der Tasten erneut gedrückt wird. 9 Optisches Laufwerk (optional) Ein optionales SATA-DVD-ROM- oder DVD-RW-Laufwerk in Flachbauweise.
Merkmale des LCD-Bedienfelds Auf dem LCD-Display werden Systeminformationen sowie Status- und Fehlermeldungen angezeigt, die darüber informieren, ob das System ordnungsgemäß funktioniert oder überprüft werden muss. Informationen über spezifische Statuscodes finden Sie im Abschnitt „Meldungen der LCDStatusanzeige“ auf Seite 28. Die LCD-Hintergrundbeleuchtung leuchtet im normalen Betriebszustand blau und im Fehlerfall gelb.
Element Tasten Beschreibung 1 Links Bewegt den Cursor schrittweise zurück. 2 Auswahl Wählt den vom Cursor markierten Menüeintrag aus. 3 Rechts Bewegt den Cursor schrittweise vor. Beim Durchlaufen einer Meldung: • Einmal drücken, um die Laufgeschwindigkeit zu erhöhen. • Erneut drücken zum Anhalten. • Noch einmal drücken, um zur StandardLaufgeschwindigkeit zurückzukehren. • Erneutes Drücken wiederholt den Zyklus.
Drücken Sie im Home-Bildschirm die Taste Auswahl, um das Hauptmenü aufzurufen. In den nachstehenden Tabellen finden Sie Informationen zu den Untermenüs Setup (Einrichtung) und View (Ansicht). Menü Setup ANMERKUNG: Wenn Sie eine Option im Setup-Menü auswählen, müssen Sie die Option bestätigen, bevor Sie den nächsten Vorgang durchführen. Option Beschreibung DRAC Wählen Sie DHCP oder Static IP, um den Netzwerkmodus zu konfigurieren.
Menü View (Anzeige) Option Beschreibung DRAC IP Anzeige der IPv4- oder IPv6-Adressen für den iDRAC6. Die Optionen sind DNS (Primary und Secondary), Gateway, IP und Subnet (kein Subnet bei IPv6). MAC Anzeige der MAC-Adressen für DRAC, iSCSIn oder NETn. Name Anzeige des Namens für Host, Model oder User String für das System. Number Anzeige der Asset tag (Systemkennnummer) oder der Service tag (Service-Tag-Nummer) des Systems. Power Anzeige der Leistungsabgabe des Systems in BTU/h oder Watt.
Festplattenanzeigemuster 1 2 1 Festplattenstatusanzeige (grün und gelb) 2 Festplattenaktivitätsanzeige (grün) Laufwerkstatusanzeigemuster (nur RAID) Zustand Blinkt grün, zweimal pro Sekunde Laufwerk identifizieren/zum Entfernen vorbereiten Aus Laufwerk bereit zum Einsetzen oder Entfernen ANMERKUNG: Die Laufwerkstatusanzeige bleibt ausgeschaltet, bis alle Festplatten nach dem Einschalten des Systems initialisiert sind.
Anzeigen und Funktionen auf der Rückseite Abbildung 1-3. Anzeigen und Funktionen auf der Rückseite 1 16 2 3 15 14 13 4 12 Symbol 5 6 11 7 10 9 8 Element Anzeige, Taste oder Anschluss Beschreibung 1 PCIe-Steckplatz 1 PCI Express (2. Generation) x8-Erweiterungssteckplatz (Länge 24,13 cm). 2 PCIe-Steckplatz 2 PCI Express (2. Generation) x4-Erweiterungssteckplatz (niedriges Profil mit maximaler Länge von 24,13 cm, Halter in Standardhöhe). 3 PCIe-Steckplatz 3 PCI Express (2.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 6 PCIe-Steckplatz 6 PCI Express (2. Generation) x8-Erweiterungssteckplatz (Länge 24,13 cm). 7 Netzteile (2) 1100-W-Netzteile. 8 Systemidentifikationstaste Die Identifikationstasten auf der Vorder- und Rückseite dienen dazu, ein bestimmtes System innerhalb eines Racks zu lokalisieren.
Element Anzeige, Taste oder Anschluss Symbol Beschreibung 15 VFlashMediensteckplatz (optional) Zum Anschluss einer externen SDSpeicherkarte für die optionale iDRAC6-Enterprise-Karte. 16 iDRAC6-EnterprisePort (optional) Eigener Management-Port für die optionale iDRAC6-Enterprise-Karte. Richtlinien für das Anschließen von externen Geräten • Schalten Sie die Stromversorgung des Systems und der externen Geräte aus, bevor Sie ein neues externes Gerät anschließen.
Anzeige Anzeigecode Verbindungsanzeige und Aktivitätsanzeige leuchten nicht. Der NIC ist nicht mit dem Netzwerk verbunden. Verbindungsanzeige leuchtet grün. Der NIC ist mit einem gültigen Netzwerkpartner bei 1000 Mbit/s verbunden. Verbindungsanzeige leuchtet gelb. Der NIC ist mit einem gültigen Netzwerkpartner bei 10/100 Mbit/s verbunden. Aktivitätsanzeige blinkt grün. Netzwerkdaten werden gesendet oder empfangen.
Abbildung 1-4.
Meldungen der LCD-Statusanzeige Die LCD-Meldungen bestehen aus kurzen Textnachrichten, die sich auf Ereignisse beziehen, die im Systemereignisprotokoll (SEL) aufgezeichnet sind. Informationen über das SEL und über die Konfiguration der Systemverwaltungseinstellungen finden Sie in der Dokumentation der Systemverwaltungssoftware. ANMERKUNG: Wenn das System nicht startet, drücken Sie die Systemidentifikationstaste mindestens 5 Sekunden lang, bis ein Fehlercode auf dem LCD-Display erscheint.
Tabelle 1-1. Code Meldungen der LCD-Statusanzeige Text E1000 Failsafe voltage error. Contact support. Ursachen Korrekturmaßnahmen Überprüfen Sie das Trennen Sie das System Systemereignisprotokoll auf für 10 Sekunden von kritische Fehlerereignisse. der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E1114 Ambient Temp exceeds allowed range.
Code Text Ursachen Korrekturmaßnahmen E1211 RAID Controller battery failure. Check battery. RAID-Akku ist nicht vorhanden, fehlerhaft, oder lässt sich aufgrund von Temperaturproblemen nicht aufladen. Setzen Sie den RAIDAkkustecker neu ein. Siehe „Installieren des RAID-Akkus“ auf Seite 151 und „Fehlerbehebung bei der Systemkühlung“ auf Seite 193. E1216 3.3V Regulator failure. Reseat PCIe cards. 3,3-V-Spannungsregler ist ausgefallen.
Code Text Ursachen Korrekturmaßnahmen E122D Memory Einer der Regler für den Regulator # Speicher ist ausgefallen. Failed. Reseat DIMMs. Setzen Sie die Speichermodule neu ein. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 195. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E122E On-board regulator failed. Call support. Einer der eingebauten Spannungsregler ist ausgefallen.
Code Text Ursachen Korrekturmaßnahmen E1310 Fan ## RPM exceeding range. Check fan. Drehzahl des angegebenen Lüfters befindet sich außerhalb des normalen Betriebsbereichs. Siehe „Fehlerbehebung bei der Systemkühlung“ auf Seite 193. E1313 Fan redundancy lost. Check fans. Die Lüfter des Systems sind nicht mehr redundant. Bei einem weiteren Lüfterausfall besteht Überhitzungsgefahr für das System. Überprüfen Sie das LCD auf weitere Laufmeldungen. Siehe „Fehlerbehebung bei einem Lüfter“ auf Seite 194.
Code Text E1418 CPU # not detected. Check CPU is seated properly. Ursachen Korrekturmaßnahmen Der angegebene Prozessor ist nicht vorhanden oder fehlerhaft, und die Systemkonfiguration wird nicht unterstützt. Stellen Sie sicher, dass der angegebene Prozessor korrekt installiert ist und dass es sich um eine unterstützte Konfiguration handelt. Siehe Tabelle 3-5 und „Fehlerbehebung bei den Prozessoren“ auf Seite 205. E141C Unsupported Die Konfiguration der CPU configu- Prozessoren wird nicht ration.
Code Text Ursachen E1420 CPU Bus Das System-BIOS hat einen parity error. Prozessor-Busparitätsfehler Power cycle gemeldet. AC. Korrekturmaßnahmen Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E1421 CPU # initialization error. Power cycle AC Das System-BIOS hat einen ProzessorInitialisierungsfehler gemeldet.
Code Text Ursachen Korrekturmaßnahmen E1618 Predictive failure on Power Supply # (### W). Check PSU. Ein Netzteillüfter-Ausfall, Siehe „Fehlerbehebung ein Übertemperaturzustand bei Netzteilen“ auf oder ein Netzteil-Kommuni- Seite 192. kationsfehler hat eine Netzteil-Ausfallvoraussage ausgelöst. E161C Power Supply # (### W) lost AC power. Check PSU cables. Das angegebene Netzteil ist an das System angeschlossen, erhält jedoch keinen Wechselstrom mehr.
Code Text Ursachen Korrekturmaßnahmen E1629 Power required > PSU wattage. Check PSU and config. Die Systemkonfiguration benötigt auch bei Drosselung mehr Strom als die Netzteile liefern können. Schalten Sie das System aus, entfernen Sie einige Hardwaregeräte oder installieren Sie Netzteile mit höherer Leistung und starten Sie das System neu. E1631 System power draw exceeded threshold. Contact support.
Code Text Ursachen Korrekturmaßnahmen E1711 PCI parity error on Bus ## Device ## Function ## Das System-BIOS hat einen PCI-Paritätsfehler bei einer Komponente im PCIKonfigurationsraum bei Bus ##, Gerät ## und Funktion ## gemeldet. Entfernen Sie die PCIeErweiterungskarten und setzen Sie sie neu ein. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Erweiterungskarten“ auf Seite 203. PCI parity error on Slot #. Review & clear SEL.
Code Text Ursachen E1714 Unknown Das System-BIOS hat einen error. Review Systemfehler erkannt, kann & clear SEL. aber nicht die Ursache feststellen. Korrekturmaßnahmen Überprüfen Sie das SEL auf weitere Informationen und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E1715 Fatal I/O Das System-BIOS hat Error.
Code Text E1717 CPU # internal error. Review & clear SEL. Ursachen Korrekturmaßnahmen Das System-BIOS hat festgestellt, dass am angegebenen Prozessor ein interner Fehler aufgetreten ist. Überprüfen Sie das SEL auf weitere Informationen, und löschen Sie dann das SEL. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221.
Code Text Ursachen Korrekturmaßnahmen E1810 Hard drive ## Bei der angegebenen fault. Review Festplatte ist ein Fehler & clear SEL. aufgetreten. Siehe „Fehlerbehebung bei einem Festplattenlaufwerk“ auf Seite 201. E1812 Hard drive ## Die angegebene Festplatte removed. wurde aus dem System Check drive. entfernt. Dient nur zur Information. E1A11 PCI Riser hardware & configuratio n mismatch. Reconfigure. PCIe-Riser sind nicht korrekt konfiguriert.
Code Text Ursachen Korrekturmaßnahmen E1814 Internal SD Module Card # writeprotected. Check SD card Die interne zweifache SDModulkarte ist schreibgeschützt und kann nicht verwendet werden. Ändern Sie die Einstellung des Schreibschutzschalters an der SD-Karte. E1815 Internal Dual SD Module redundancy lost. Check SD cards. Das startfähige Medium im internen zweifachen SDModul ist nicht mehr redundant. Setzen Sie die interne zweifache SD-Modulkarte neu ein. E1A14 SAS cable A failure.
Code Text Ursachen E1A1D Control panel USB-Kabel zum Bedienfeld USB cable not fehlt oder ist defekt. detected. Check cable. Korrekturmaßnahmen Befestigen Sie das Kabel. Falls das Problem weiterhin besteht, tauschen Sie das Kabel aus. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E2010 Memory not detected. Inspect DIMMs. Im System wurde kein Speicher erkannt. Installieren Sie Speichermodule oder setzen Sie die Speichermodule neu ein.
Code Text E2014 CMOS RAM failure. Power cycle AC. Ursachen Korrekturmaßnahmen CMOS-Fehler. CMOS-RAM Trennen Sie das System funktioniert nicht korrekt. für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E2015 DMA Controller failure. Power cycle AC. DMA-Controllerfehler. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu.
Code Text E2018 Programmable Timer error. Power cycle AC. Ursachen Korrekturmaßnahmen Fehler beim programmierbaren Intervallzeitgeber. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E2019 Parity error. Paritätsfehler Power cycle AC. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu.
Code Text E201C SMI initialization failure. Power cycle AC. Ursachen Korrekturmaßnahmen SMI-Initialisierungsfehler (System Management Interrupt). Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. E201D Shutdown test Fehler beim BIOSfailure. Shutdown-Test. Power cycle AC. Trennen Sie das System für 10 Sekunden von der Stromversorgung, und starten Sie das System neu.
Code Text Ursachen E2021 Incorrect Falsche Speichermemory konfiguration. configuration. Review User Guide. Korrekturmaßnahmen Auf dem Bildschirm werden spezifische Fehlermeldungen angezeigt. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 195. E2022 General failure during POST. Check screen message. Allgemeiner Fehler nach Grafik. E2023 BIOS unable to mirror memory. Check DIMMs.
Code Text Ursachen Korrekturmaßnahmen E2110 Multibit Am Speichermodul im Error on DIMM Sockel ## ist ein Multi-Bit##. Reseat Fehler (MBE) aufgetreten. DIMM. Setzen Sie das Speichermodul neu im Sockel ein. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung beim Systemspeicher“ auf Seite 195. E2111 SBE log disabled on DIMM ##. Reseat DIMM.
Code Text Ursachen I1910 Intrusion Die Systemabdeckung ist detected. abgenommen. Check chassis cover. Korrekturmaßnahmen Dient nur zur Information. LCD-Überlaufmeldung. Auf dem LCD-Display können höchstens zehn Fehlermeldungen angezeigt werden. Die elfte Meldung fordert den Benutzer auf, im SEL nach Details zu den Ereignissen zu suchen. Weitere Informationen zu den Ereignissen sind im Systemereignisprotokoll (SEL) enthalten. I1912 SEL full. Review & clear log.
Systemmeldungen Systemmeldungen werden auf dem Bildschirm angezeigt, um Sie auf mögliche Systemprobleme aufmerksam zu machen. ANMERKUNG: Wenn eine Systemmeldung ausgegeben wird, die nicht in der Tabelle aufgeführt ist, können Sie die Erklärung der Meldung und die empfohlene Maßnahme in der Dokumentation zur Anwendung, welche bei der Anzeige der Meldung ausgeführt wird, oder in der Dokumentation zum Betriebssystem, nachschlagen. Tabelle 1-2.
Meldung Ursachen Korrekturmaßnahmen Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving. Die Speicherkonfiguration unterstützt kein KnotenInterleaving, oder die Konfiguration wurde geändert (zum Beispiel ein defektes Speichermodul), so dass kein KnotenInterleaving erfolgen kann. Das System funktioniert zwar, aber ohne KnotenInterleaving. Stellen Sie sicher, dass die Speichermodule in einer Konfiguration installiert werden, die KnotenInterleaving unterstützt.
Meldung Ursachen Korrekturmaßnahmen Alert! Redundant memory disabled! Memory configuration does not support redundant memory. Memory Mirroring wurde im System-Setup-Programm aktiviert, aber die derzeitige Konfiguration unterstützt keinen redundanten Speicher. Möglicherweise ist ein Speichermodul fehlerhaft. Überprüfen Sie die Speichermodule auf Defekte. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 195. Setzen Sie gegebenenfalls die Speichereinstellung zurück.
Meldung Ursachen Korrekturmaßnahmen Caution! NVRAM_CLR jumper is installed on system board NVRAM_CLR-Jumper ist in der Einstellung zum Löschen installiert. CMOS wurde gelöscht. Setzen Sie den NVRAM_CLR-Jumper auf die Standardposition (Kontaktstifte 3 und 5). Die Position des Jumpers ist in Abbildung 6-1 dargestellt. Starten Sie das System neu und legen Sie die BIOSEinstellungen erneut fest. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 71.
Meldung Ursachen Korrekturmaßnahmen Current boot mode is set to UEFI. Please ensure compatible bootable media is available. Use the system setup program to change the boot mode as needed. Das System konnte nicht gestartet werden, da UEFI Boot Mode im BIOS aktiviert ist und das Startbetriebssystem UEFI nicht unterstützt. Stellen Sie sicher, dass der Boot Mode korrekt eingestellt ist und das entsprechende startfähige Medium verfügbar ist.
Meldung Ursachen Korrekturmaßnahmen General failure Das Betriebssystem konnte den Befehl nicht ausführen. Diese Meldung wird normalerweise von genaueren Angaben begleitet. Notieren Sie sich die Informationen und führen Sie die entsprechenden Maßnahmen durch, um das Problem zu beheben. Invalid configuration information please run SETUP program. Eine unzulässige Systemkonfiguration hat zu einem Systemhalt geführt. Führen Sie das SystemSetup-Programm aus und überprüfen Sie die Einstellungen.
Meldung Ursachen Korrekturmaßnahmen Local keyboard Die USB-Ports sind im may not work System-BIOS deaktiviert. because all user accessible USB ports are disabled. If operating locally, power cycle the system and enter system setup program to change settings. DIMMs disabled Memory Buffer communication error Schalten Sie das System aus und starten Sie es mit dem Netzschalter neu und aktivieren Sie dann im System-Setup-Programm die USB-Ports. Siehe „Aufrufen des System-SetupProgramms“ auf Seite 72.
Meldung Ursachen DIMMs disabled MemBIST error Das Speichermodul ist nicht Ersetzen Sie das/die korrekt eingesetzt. Speichermodule oder setzen Sie sie neu ein. Siehe Der Speichermodulsockel oder der Prozessorsockel ist „Entfernen von Speichermodulen“ auf möglicherweise mit Staub Seite 125 und „Installieren verschmutzt. von Speichermodulen“ auf Nicht unterstütztes Seite 123. Speichermodul.
Meldung Ursachen Korrekturmaßnahmen DIMMs disabled Invalid DIMM Nicht unterstützte Speichermodule im ersten Lockstep-Paar. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 119. Setzen Sie die Speichermodule wieder ein. Siehe „Entfernen von Speichermodulen“ auf Seite 125 und „Installieren von Speichermodulen“ auf Seite 123. DIMM Nicht unterstützte unsupported: Speichermodule. DIMM Lockstep pair DIMM disabled. Please replace the DIMM or remove the lockstep pair.
Meldung Ursachen MemBIST timeout: DIMM Lockstep Pair DIMM disabled. Please replace the DIMM(s) or remove the lockstep pair. Die Speichermodule sind nicht korrekt eingesetzt. Ersetzen Sie das/die Speichermodule oder setzen Der Speichermodulsockel ist Sie sie neu ein. Siehe „Entfernen von möglicherweise Staub Speichermodulen“ auf ausgesetzt. Seite 125 und „Installieren Defektes Speichermodul. von Speichermodulen“ auf Seite 123. MemBIST error: DIMM Lockstep Pair DIMM disabled.
Meldung Ursachen Korrekturmaßnahmen DIMM population violation: DIMM Lockstep Pair DIMM disabled. Please populate DIMM(s) with largest number of ranks in the lowest slot. Speichermodule mit verschiedenen Rängen wurden gemischt in einer unzulässigen Konfiguration eingesetzt. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 119. The memory configuration is not optimal.
Meldung Ursachen Korrekturmaßnahmen Memory double word logic failure at address, read value expecting value Fehlerhafte oder nicht ordnungsgemäß installierte Speichermodule. Siehe „Fehlerbehebung beim Systemspeicher“ auf Seite 195. Memory Initialization Warning: Memory size may be reduced Unzulässige Speicherkonfiguration erkannt. Das System funktioniert, aber mit weniger Speicher als physisch verfügbar. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind.
Meldung Ursachen Korrekturmaßnahmen No boot device available Fehlerhaft oder nicht vorhanden: Subsystem für optisches Laufwerk, Festplatte oder Festplattensubsystem; oder es ist nicht-startfähiger USBStick installiert. Verwenden Sie einen startfähigen USB-Stick, eine startfähige CD oder ein startfähiges Festplattenlaufwerk.
Meldung Ursachen Korrekturmaßnahmen No timer tick interrupt Defekte Systemplatine. Siehe „Wie Sie Hilfe bekommen“ auf Seite 221. PCI BIOS failed to install Prüfsummenfehler bei PCIeGeräte-BIOS (OptionsROM) während des Shadowing erkannt. Setzen Sie die Erweiterungskarte(n) neu ein. Stellen Sie sicher, dass alle erforderlichen Kabel sicher mit den Erweiterungskarten verbunden sind. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei Erweiterungskarten“ auf Seite 203.
Meldung Ursachen Korrekturmaßnahmen Read fault Das Betriebssystem kann vom Festplattenlaufwerk, dem optischen Laufwerk oder dem USB-Gerät nicht lesen, das System konnte einen bestimmten Sektor auf der Festplatte nicht finden, oder der angeforderte Sektor ist defekt. Ersetzen Sie das optische Medium, das USB-Medium oder das USB-Gerät. Stellen Sie sicher, dass die SASRückwandplatinen-, USBoder SATA-Kabel korrekt angeschlossen sind.
Meldung Ursachen Korrekturmaßnahmen Sector not found Das Festplattenlaufwerk, USB-Gerät oder USBSeek error Medium ist defekt. Seek operation failed Ersetzen Sie das USBMedium oder das Gerät. Stellen Sie sicher, dass die USB- oder SASRückwandplatinenkabel korrekt angeschlossen sind. Entsprechende Informationen zu den im System installierten Laufwerken finden Sie unter „Fehlerbehebung bei einem USB-Gerät“ auf Seite 186 oder „Fehlerbehebung bei einem Festplattenlaufwerk“ auf Seite 201.
Meldung Ursachen Korrekturmaßnahmen Time-of-day not set - please run SETUP program Die Einstellungen für Time oder Date sind falsch; fehlerhafte Systembatterie. Überprüfen Sie die Uhrzeitund Datumseinstellungen. Siehe „Verwenden des System-Setup-Programms und des UEFI-BootManagers“ auf Seite 71. Besteht das Problem weiterhin, ersetzen Sie die Systembatterie. Siehe „Systembatterie“ auf Seite 166. Timer chip Defekte Systemplatine. counter 2 failed Siehe „Wie Sie Hilfe bekommen“ auf Seite 221.
Meldung Ursachen Korrekturmaßnahmen Unable to launch System Services image. System halted! System wurde nach F10-Tastendruck angehalten, weil das System Services-Image in der System-Firmware beschädigt ist oder aufgrund eines Systemplatinenaustauschs verloren ist. Starten Sie das System neu und aktualisieren Sie das Lifecycle-ControllerRepository auf die neueste Software, um die volle Funktionalität wiederherzustellen.
Meldung Ursachen Korrekturmaßnahmen Warning: A fatal error has caused system reset! Please check the system event log! Ein schwerwiegender Systemfehler ist aufgetreten und führte zum Systemneustart. Überprüfen Sie das SEL auf Informationen, die während des Fehlers protokolliert wurden. Lesen Sie den entsprechenden Abschnitt zur Fehlerbehebung in „Fehlerbehebung am System“ auf Seite 185 hinsichtlich fehlerhafter Komponenten, die im SEL auftauchen. Warning: Control Panel is not installed.
Meldung Ursachen Korrekturmaßnahmen The memory configuration is not optimal. The recommended memory configuration is: Unzulässige Speicherkonfiguration erkannt. Das System läuft, jedoch mit eingeschränkter Funktionalität. Stellen Sie sicher, dass die Speichermodule in einer gültigen Konfiguration installiert sind. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 119. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung beim Systemspeicher“ auf Seite 195.
Meldung Ursachen Korrekturmaßnahmen Warning: QPI links operating in Slow Speed Mode. Der Prozessor hat verbogene Kontaktstifte. Der Prozessor ist nicht korrekt im Prozessorsockel eingesetzt. Setzen Sie die Prozessoren neu ein. Siehe „Entfernen eines Prozessors“ auf Seite 155 und „Installieren eines Prozessors“ auf Seite 159. Warning: QPI link between Port and failed. Warning: QPI link between Port and degraded to half-width.
Diagnosemeldungen Die Diagnoseprogramme des Systems geben eventuell Meldungen aus. Weitere Informationen zur Systemdiagnose finden Sie unter „Ausführen der Systemdiagnose“ auf Seite 207. Alarmmeldungen Die Systemverwaltungssoftware erzeugt Alarmmeldungen für das System. Alarmmeldungen bestehen aus Informations-, Status-, Warn- und Fehlermeldungen zu Laufwerks-, Temperatur-, Lüfter- und Stromversorgungsbedingungen.
Verwenden des System-SetupProgramms und des UEFI-BootManagers Das System-Setup-Programm ist das BIOS-Programm, mit dem Sie die Systemhardware verwalten und Optionen auf BIOS-Ebene festlegen können.
Der Startmodus wird im Feld Boot Mode des „Bildschirm Boot Settings (Starteinstellungen)“ auf Seite 79 im System-Setup-Programm ausgewählt. Installieren Sie nach dem Festlegen des Startmodus das Betriebssystem in diesem Modus. Starten Sie danach das System im gleichen Startmodus (BIOS oder UEFI), um auf das installierte Betriebssystem zuzugreifen. Wenn Sie versuchen, das Betriebssystem in einem anderen Startmodus zu starten, führt zum sofortigen Anhalten des Systems beim Start.
Verwenden der Steuertasten des System-Setup-Programms Tasten Maßnahme Pfeil-nach-oben-Taste oder Zurück zum vorherigen Feld. Pfeil-nach-unten-Taste oder Weiter zum nächsten Feld. Leertaste, <+>, < –>, Pfeil-nach-links- und Pfeilnach-rechts-Taste Zeigt die möglichen Einstellungen eines Feldes nacheinander an. In vielen Feldern kann der gewünschte Wert auch direkt eingegeben werden.
Optionen des System-Setup-Programms Hauptbildschirm ANMERKUNG: Welche Optionen angezeigt werden, hängt von der Konfiguration des Systems ab. ANMERKUNG: Die Standardeinstellungen des System-Setup-Programms sind in den folgenden Abschnitten gegebenenfalls bei den jeweiligen Optionen angegeben. Option Beschreibung System Time Uhrzeiteinstellung der internen Systemuhr. System Date Datumseinstellung des internen Kalenders. Memory Settings Zeigt Informationen zum installierten Arbeitsspeicher an.
Option Beschreibung Processor Settings Zeigt Informationen zu den Prozessoren an (Geschwindigkeit, Cache-Größe usw.). Siehe „Bildschirm Processor Settings (Prozessoreinstellungen)“ auf Seite 77. SATA Settings Zeigt einen Bildschirm an, über den der integrierte SATA-Controller und die zugehörigen Ports aktiviert oder deaktiviert werden. Siehe „Bildschirm SATA Settings (SATA-Einstellungen)“ auf Seite 79. Boot Settings Zeigt einen Bildschirm an, über den der Startmodus (BIOS oder UEFI) eingestellt wird.
Option Beschreibung Power Management Ermöglicht das Festlegen von vorkonfigurierten oder individuell angepassten Energieverbrauchseinstellungen für Prozessor(en), Lüfter und Speichermodule. Siehe „Bildschirm Power Management (Energieverwaltung)“ auf Seite 84. System Security Zeigt den Bildschirm zur Konfiguration der Systemund Setup-Kennwortfunktionen an.
Bildschirm Memory Settings (Speichereinstellungen) Option Beschreibung System Memory Size Zeigt die Größe des Systemspeichers an. System Memory Type Zeigt den Typ des Systemspeichers an. System Memory Speed Zeigt die Systemspeichertaktrate an. Video Memory Zeigt die Größe des Grafikspeichers an. System Memory Testing (Standardeinstellung Disabled) Legt fest, ob Systemspeichertests beim Start ausgeführt werden. Die Optionen sind Enabled und Disabled.
Option Beschreibung Logical Processor (Standardeinstellung Enabled) Ein SMT-fähiger Prozessor (Simultaneous MultiThreading Technology) unterstützt bis zu zwei logische Prozessoren. Wenn dieses Feld auf Enabled gesetzt ist, meldet das BIOS beide logischen Prozessoren. Bei der Einstellung Disabled wird vom BIOS nur ein logischer Prozessor erkannt.
Option Beschreibung Processor X FamilyModel-Stepping Zeigt die Serien- und Modellnummer der vorhandenen Prozessoren an. Ein Untermenü enthält die Kerngeschwindigkeit, die Größe des Cache-Speichers und die Anzahl der Prozessorkerne. Bildschirm SATA Settings (SATA-Einstellungen) Option Beschreibung Embedded SATA ATA Mode aktiviert den integrierten SATA-Controller. (Standardeinstellung Off) Off deaktiviert den Controller.
Option Beschreibung Hard-Disk Drive Sequence Legt die Reihenfolge der Festplattenlaufwerke fest, von denen das BIOS während des Systemstarts zu starten versucht. USB Flash Drive Emulation Type Legt den Emulationstyp für das USB-Flash-Laufwerk fest. Wenn Boot Mode auf UEFI gesetzt ist, ist dieses Feld deaktiviert. Boot Sequence Retry (Standardeinstellung Disabled) Wenn diese Option aktiviert ist, versucht das System bei einem fehlgeschlagenen Startversuch nach 30 Sekunden erneut zu starten.
Option Beschreibung MAC-Adresse Zeigt die MAC-Adresse für den integrierten 10/100/1000-NIC an. Capability Detected (Standardeinstellung Disabled) Zeigt die NIC-Funktionen des LOM-NICHardwareschlüssels an. ANMERKUNG: Für bestimmte LOM-Funktionen muss eventuell ein zusätzlicher Treiber installiert werden. OS Watchdog Timer (Standardeinstellung Disabled) Zur Unterstützung bei der Wiederherstellung des Betriebssystems, wenn das System nicht mehr reagiert.
Bildschirm Serial Communication Option Beschreibung Serial Communication (Standardeinstellung On without Console Redirection) Legt fest, ob serielle Datengeräte (Serial Device 1 und Serial Device 2) im BIOS aktiviert sind. BIOSKonsolenumleitung kann auch aktiviert werden, und die verwendete Portadresse lässt sich festlegen. Die Optionen sind On without Console Redirection, On with Console Redirection via COM1, On with Console Redirection via COM2 und Off.
Bildschirm Embedded Server Management (Integrierte Serververwaltung) Option Beschreibung Front-Panel LCD Options Die Optionen sind User Defined String, Model Number oder None. Wenn der LCD-Home-Bildschirm nicht auf eine dieser Einstellungsmöglichkeiten, sondern auf eine andere Option gesetzt ist, wird diese im BIOS als „Advanced“ (Erweitert) angezeigt. In diesem Fall kann die Einstellung im BIOS nicht geändert werden, solange sie nicht über ein anderes LCD-Konfigurationsprogramm (z. B.
Bildschirm Power Management (Energieverwaltung) Option Beschreibung Power Management Optionen sind OS Control, Active Power Controller, Custom oder Maximum Performance. Bei allen Einstellungen mit Ausnahme von Custom sind die Energieverwaltungsoptionen im BIOS vorkonfiguriert: • Bei der Einstellung OS Control wird die CPU-Leistung auf OS DBPM gesetzt, die Lüfterleistung auf Minimum Power und die Speicherleistung auf Maximum Performance.
Bildschirm System Security (Systemsicherheit) Option Beschreibung System Password Zeigt den aktuellen Status der Kennwortsicherheitsfunktion an und ermöglicht die Zuweisung und Überprüfung eines neuen Systemkennworts. ANMERKUNG: Weitere Informationen finden Sie unter „Verwenden des Systemkennworts“ auf Seite 90. Setup Password Schränkt den Zugriff auf das System-Setup-Programm durch ein Setup-Kennwort ein.
Option Beschreibung TPM Clear (Standardeinstellung No) VORSICHTSHINWEIS: Löschen des TPM führt zum Verlust aller Schlüssel im TPM. Diese Option verhindert, dass das Betriebssystem gestartet werden kann und führt zu Datenverlusten, falls sich die Schlüssel nicht wiederherstellen lassen. Erstellen Sie unbedingt eine Sicherungskopie der TPM-Schlüssel, bevor Sie diese Option aktivieren. Bei der Einstellung Yes wird der gesamte Inhalt des TPM gelöscht.
Option Beschreibung AC Power Recovery Delay Bestimmt, wann das System nach Wiederherstellung der Stromversorgung neu startet. Die verfügbaren Optionen sind: Immediate (Sofort), Random (Zufallswert zwischen 30 und 240 Sekunden) oder ein benutzerdefinierter Wert zwischen 30 und 240 Sekunden. User Defined Delay Hiermit kann der Benutzer den aktuellen Wert für AC Recovery Delay anzeigen. Mit diesem Feld lässt sich außerdem ein neuer Wert für AC Recovery Delay festlegen.
2 Drücken Sie die Taste , wenn folgende Meldung angezeigt wird: = UEFI Boot Manager ANMERKUNG: Das System reagiert erst, wenn die USB-Tastatur aktiv ist. Wenn der Ladevorgang des Betriebssystems beginnt, bevor Sie gedrückt haben, lassen Sie das System den Start ausführen. Starten Sie dann das System neu und versuchen Sie es erneut. Verwenden der Navigationstasten des UEFI-Boot-Managers Tasten Maßnahme Pfeil nach oben Markiert das vorangehende Feld.
Option Beschreibung UEFI Boot Settings Zum Hinzufügen, Löschen, Aktivieren oder Deaktivieren von Startoptionen, Ändern der Startreihenfolge oder einmaligem Ausführen einer Startoption. System Utilities Für den Zugriff auf das System-Setup-Programm, Systemdienste (Unified Server Configurator, USC), Diagnose und Startoptionen auf BIOS-Ebene. Bildschirm UEFI Boot Settings Option Beschreibung Add Boot Option Fügt eine neue Startoption hinzu. Delete Boot Option Löscht eine vorhandene Startoption.
System- und Setup-Kennwortfunktionen ANMERKUNG: Falls das Kennwort verlorengegangen ist, lesen Sie „Deaktivieren eines verlorenen Kennworts“ auf Seite 219. Im Lieferzustand ist die Systemkennwortfunktion nicht aktiviert. Das System sollte nur mit Kennwortschutz betrieben werden. VORSICHTSHINWEIS: Kennwörter bieten einen gewissen Schutz für die auf dem System gespeicherten Daten.
3 Geben Sie das neue Systemkennwort ein. Das Kennwort darf bis zu 32 Zeichen lang sein. Beim Eingeben der Zeichen werden Platzhalter im Feld angezeigt. Bei der Kennwortzuweisung wird nicht zwischen Groß- und Kleinschreibung unterschieden. Bestimmte Tastenkombinationen sind ungültig; wenn Sie sie eingeben, gibt das System einen Signalton aus. Drücken Sie zum Löschen von Zeichen die Rücktaste oder die Nachlinks-Taste.
So deaktivieren Sie den Kennwortschutz: 1 Schalten Sie das System ein oder führen Sie mit einen Neustart durch. 2 Geben Sie das Kennwort ein und drücken Sie . Wenn Password Status auf Locked gesetzt ist, geben Sie beim Neustart nach Aufforderung das Kennwort ein und drücken Sie die . Wenn ein falsches Systemkennwort eingegeben wurde, zeigt das System eine Meldung an und fordert Sie zur Eingabe des Kennworts auf.
Verwenden des Setup-Kennworts Zuweisen eines Setup-Kennworts Ein Setup-Passwort kann nur zugewiesen werden, wenn die Option Setup Password auf Not Enabled gesetzt ist. Um ein Setup-Kennwort zuzuweisen, markieren Sie die Option Setup Password und drücken Sie die Taste <+> oder <–>. Das System fordert Sie dazu auf, ein Kennwort einzugeben und zu bestätigen. ANMERKUNG: Es ist möglich, das gleiche Kennwort als System- und als SetupKennwort zu verwenden.
Betrieb mit aktiviertem Setup-Kennwort Wenn die Option Setup Password auf Enabled gesetzt ist, muss zuerst das korrekte Kennwort eingegeben werden, bevor die meisten Optionen des System-Setups bearbeitet werden können. Wird auch beim dritten Versuch nicht das korrekte Passwort eingegeben, können die Einstellungen in den Bildschirmen des System-Setups zwar angezeigt aber nicht geändert werden.
Integrierte Systemverwaltung Der Lifecycle-Controller ist ein integriertes Dienstprogramm, das Systemverwaltungsaufgaben aus einer integrierten Umgebung während der gesamten Server-Lebensdauer ermöglicht. Der Lifecycle-Controller lässt sich während des Startvorgangs aufrufen und unabhängig vom Betriebssystem verwenden. ANMERKUNG: Bestimmte Plattformkonfigurationen unterstützen möglicherweise nicht alle Funktionen des Lifecycle-Controllers.
• SEL-Meldungen (Systemereignisprotokoll) anzeigen oder Meldungen aus dem Protokoll löschen • iDRAC6-Einstellungen auf Standardwerte zurücksetzen Weitere Informationen zur Nutzung des iDRAC6 finden Sie auch in der Dokumentation zum iDRAC6 und zu den Systemverwaltungsanwendungen. Aufrufen des iDRAC6-Konfigurationsprogramms 1 Schalten Sie das System ein oder starten Sie es neu. 2 Drücken Sie bei der Aufforderung während des POST.
Installieren von Systemkomponenten Empfohlene Werkzeuge Für die in diesem Abschnitt beschriebenen Maßnahmen benötigen Sie gegebenenfalls folgende Werkzeuge: • Schlüssel für das Systemschloss • Kreuzschlitzschraubendreher der Größen 1 und 2 • Torx-Schraubendreher der Größen T8 und T10 • Erdungsband Das Innere des Systems WARNUNG: Beim Anheben des Systems sollten Sie sich stets von jemand anders helfen lassen. Um Verletzungen zu vermeiden, sollten Sie nicht versuchen, das System allein zu bewegen.
Abbildung 3-1.
Frontverkleidung (optional) Entfernen der Frontverkleidung 1 Entriegeln Sie das Systemschloss am linken Rand der Frontverkleidung. 2 Heben Sie die Sperrklinke neben dem Schloss an. 3 Schwenken Sie die linke Seite der Frontverkleidung von der Vorderseite des Systems weg. 4 Lösen Sie die rechte Seite der Frontverkleidung aus dem Haken und nehmen Sie die Frontverkleidung vom System ab. Siehe Abbildung 3-2. Abbildung 3-2.
Öffnen und Schließen des Systems WARNUNG: Beim Anheben des Systems sollten Sie sich stets von jemand anders helfen lassen. Um Verletzungen zu vermeiden, sollten Sie nicht versuchen, das System allein zu bewegen. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-3. System öffnen und schließen 1 2 3 1 Freigabehebel 3 Abdeckung 2 Verriegelung Schließen des Systems 1 Positionieren Sie die Abdeckung auf dem Gehäuse und versetzen Sie es leicht zur Systemrückseite, damit die Aussparungen auf den Seiten der Abdeckung in die entsprechenden Haken auf den Gehäuseseiten greifen. Siehe Abbildung 3-3. 2 Schieben Sie die Abdeckung zur Gehäusevorderseite, bis sie einrastet.
Festplattenlaufwerke Alle Laufwerke sind über die SAS/SATA-Rückwandplatine in der vorderen Gehäusebaugruppe mit der Systemplatine verbunden. Die Festplatten befinden sich in hot-swap-fähigen Laufwerkträgern, die in die Festplattenschächte passen.
Abbildung 3-4. Festplattenplatzhalter entfernen oder installieren 1 2 1 Festplattenplatzhalter 2 Entriegelungstaste Installieren eines Festplattenplatzhalters 1 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 99. 2 Schieben Sie den Laufwerkplatzhalter in den Laufwerkschacht, bis die blaue Freigabetaste einrastet. 3 Bringen Sie gegebenenfalls die Frontverkleidung an. Siehe „Installieren der Frontverkleidung“ auf Seite 99.
Entfernen eines Laufwerkträgers VORSICHTSHINWEIS: Stellen Sie sicher, dass das Betriebssystem Hot-SwapLaufwerkinstallation unterstützt. Informationen hierzu finden Sie in der Dokumentation zum Betriebssystem. 1 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 99. 2 Bereiten Sie das Laufwerk mit der Verwaltungssoftware zum Entfernen vor.
Abbildung 3-5. Festplattenträger entfernen und installieren 1 2 3 1 Entriegelungstaste 3 Bügel des Festplattenträgers 2 Festplattenträger Installieren eines Laufwerkträgers VORSICHTSHINWEIS: Verwenden Sie nur Festplatten, die geprüft und für den Einsatz mit der SAS/SATA-Rückwandplatine zugelassen sind. VORSICHTSHINWEIS: Stellen Sie beim Installieren von Festplatten sicher, dass die angrenzenden Laufwerke vollständig installiert sind.
3 Drücken Sie auf die Taste auf der Vorderseite des Laufwerkträgers und öffnen Sie den Bügel. 4 Schieben Sie den Laufwerkträger in den Schacht, bis der Träger die Rückwandplatine berührt. 5 Schließen Sie den Bügel des Laufwerkträgers, um das Laufwerk zu verriegeln. Entfernen einer Festplatte aus einem Laufwerkträger Entfernen Sie die Schrauben von den Führungsschienen am Laufwerkträger und trennen Sie die Festplatte vom Träger. Siehe Abbildung 3-6. Abbildung 3-6.
Installieren einer Festplatte im Laufwerkträger 1 Führen Sie die Festplatte in den Festplattenträger ein, wobei sich das Anschlussende des Laufwerks hinten befindet. Siehe Abbildung 3-6. 2 Richten Sie die Schraublöcher in der Festplatte mit den hinteren Löchern am Laufwerkträger aus. 3 Befestigen Sie die vier Schrauben, um die Festplatte am Laufwerkträger zu sichern.
4 Trennen Sie das Stromversorgungs- und Datenkabel von der Rückseite des Laufwerks. Merken Sie sich die Führung des Stromversorgungs- und des Datenkabels seitlich im System, wenn Sie diese von der Systemplatine und vom Laufwerk trennen. Sie müssen diese Kabel beim späteren Wiedereinsetzen korrekt anbringen, damit sie nicht abgeklemmt oder gequetscht werden. Weitere Informationen finden Sie in Schritt 2 und Schritt 3 von „Verschieben der vorderen Gehäusebaugruppe“ auf Seite 116.
Abbildung 3-7.
Installation eines optischen Laufwerks VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Netzteile Das System unterstützt zwei 1100-W-Netzteilmodule. Wenn zwei Netzteile installiert sind, sorgt das zweite Netzteil für die hotswap-fähige Redundanz der Stromversorgung. In der redundanten Betriebsart wird die Stromlast auf beide Netzteile verteilt, um die Effizienz zu maximieren. Wenn ein Netzteil bei eingeschaltetem System entfernt wird, übernimmt das verbleibende Netzteil die gesamte Stromlast. In Tabelle 3-1 sind die redundanten Netzteilbetriebsarten aufgeführt. Tabelle 3-1.
Abbildung 3-8.
Installieren eines Netzteils 1 Stellen Sie sicher, dass die Netzteile vom gleichen Typ sind und die gleiche maximale Ausgangsleistung haben. ANMERKUNG: Die maximale Leistungsabgabe (in Watt) ist auf dem Netzteiletikett angegeben. 2 Entfernen Sie gegebenenfalls den Netzteilplatzhalter. Siehe „Entfernen des Netzteilplatzhalters“ auf Seite 113. 3 Schieben Sie das neue Netzteil in das Gehäuse, bis das Netzteil vollständig eingesetzt ist und die Sperklinke einrastet. Siehe Abbildung 3-8.
Kühlgehäuse Das Kühlgehäuse überdeckt die Speichermodule und sorgt für den Luftstrom im System. Entfernen des Kühlgehäuses VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst übernehmen, wenn dies in der Produktdokumentation ausdrücklich vorgesehen ist oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden.
Abbildung 3-9. Kühlgehäuse entfernen und installieren 1 2 1 Kühlgehäuse 2 Vorsprünge am Kühlgehäuse (4) Installieren des Kühlgehäuses ANMERKUNG: Um das Kühlgehäuse korrekt im Systemgehäuse einzusetzen, müssen Sie darauf achten, dass die Kabel entlang der Systemgehäusewand verlegt sind. Siehe Abbildung 3-10. 1 Verlegen Sie die Stromversorgungs- und Datenkabel entlang der Systemgehäusewand. Siehe Schritt 2 und Schritt 3 von „Verschieben der vorderen Gehäusebaugruppe“ auf Seite 116.
Vordere Gehäusebaugruppe In der vorderen Gehäusebaugruppe befinden sich die Festplatten, die SAS/SATA-Rückwandplatine, das optische Laufwerk, die Bedienfeldbaugruppe und das Anzeigemodul. Die vordere Gehäusebaugruppe ist mit einem Schienensystem an den Gehäusewänden befestigt. Verschieben der vorderen Gehäusebaugruppe So schieben Sie die vordere Gehäusebaugruppe vom Gehäuse weg: 1 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 99.
Abbildung 3-10.
So schieben Sie die vordere Gehäusebaugruppe in das Gehäuse zurück: 1 Schieben Sie die Baugruppe nach innen, bis sie in der Einbauposition einrastet. ANMERKUNG: Um eine ordnungsgemäße Systemkühlung zu gewährleisten, achten Sie darauf, dass die Kabel im System den Luftstrom nicht behindern. 2 Führen Sie die SAS- und SATA-Kabel an der Gehäusewand entlang und am RAID-Akkuhalter vorbei. Siehe Abbildung 3-10.
In Ein- und Zwei-Prozessorkonfigurationen werden FlexMem-Brücken in den angrenzenden Prozessorsockeln installiert, damit die Prozessoren in den Sockeln 1 und 2 auf den benachbarten Speichersatz zugreifen können. Weitere Informationen finden Sie unter Tabelle 3-5.
Tabelle 3-2. Speicherkonfigurationen (gleiche DIMM-Größe) 120 Anzahl der Prozessoren Systemkapazität (in GB) DIMM-Größe (in GB) Anzahl der DIMMs ANMERKUNG: Die DIMMs A1-A8 sind Prozessor 1 zugewiesen, die DIMMs B1-B8 sind Prozessor 2 zugewiesen usw. Bei Konfigurationen zwei Prozessoren sind die DIMMs A1-A8 und die DIMMs C1-C8 Prozessor 1 zugewiesen, während die DIMMs B1-B8 und die DIMMs D1-D8 Prozessor 2 zugewiesen sind.
Systemkapazität (in GB) DIMM-Größe (in GB) Anzahl der DIMMs 64 4 16 X A1,A3, A2,A4 B1,B3, B2,B4 C1,C3, C2,C4 D1,D3, D2,D4 2/4 96 4 24 X A1,A3, A5,A2, A4,A6 B1,B3, B5,B2, B4,B6 C1,C3, C5,C2, C4,C6 D1,D3, D5,D2, D4,D6 2/4 128 4 32 X A1,A2, A3,A4, A5,A6, A7,A8 B1,B2, B3,B4, B5,B6, B7,B8 C1,C2, C3,C4, C5,C6, C7,C8 D1,D2, D3,D4, D5,D6, D7,D8 2/4 128 8 16 X A1,A3, A2,A4 B1,B2, B3,B4 C1,C2, C3,C4 D1,D2, D3,D4 2/4 192 8 24 X A1,A3, A5,A2, A4,A6 B1,B3, B5,B2, B4,B6 C1,C3,
Tabelle 3-3. Speicherkonfigurationen (gemischte DIMM-Größen) Speichersockel (DIMM-Größe pro Sockel in GB) Prozessoren Anzahl der DIMMs Systemkapazität (in GB) ANMERKUNG: Die DIMMs A1-A8 sind Prozessor 1 zugewiesen, die DIMMs B1-B8 sind Prozessor 2 zugewiesen usw. Bei Konfigurationen zwei Prozessoren sind die DIMMs A1-A8 und die DIMMs C1-C8 Prozessor 1 zugewiesen, während die DIMMs B1-B8 und die DIMMs D1-D8 Prozessor 2 zugewiesen sind.
Installieren von Speichermodulen WARNUNG: Die Speichermodule bleiben nach dem Ausschalten des Systems eine Zeitlang auf hoher Temperatur. Lassen Sie die Speichermodule ausreichend lange abkühlen, bevor Sie sie berühren. Fassen Sie Speichermodule an den Rändern an und vermeiden Sie den Kontakt mit Komponenten auf Speichermodulen. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-11. Speichermodul installieren und entfernen 1 2 3 1 Speichermodul 3 Passung 2 Auswurfhebel (2) 8 Richten Sie den Stecker des Speichermoduls an den Abgleichmarkierungen des Speichermodulsockels aus und setzen Sie das Speichermodul in den Sockel ein. ANMERKUNG: Die Passung im Speichermodulsockel sorgt dafür, dass die Speichermodule nicht verkehrt herum installiert werden können. 9 Drücken Sie das Speichermodul mit den Daumen nach unten und sichern Sie so das Modul im Sockel.
12 Bringen Sie gegebenenfalls die Frontverkleidung an. Siehe „Installieren der Frontverkleidung“ auf Seite 99. 13 Setzen Sie das Kühlgehäuse ein. Siehe „Installieren des Kühlgehäuses“ auf Seite 115. 14 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 15 Starten Sie das System. Drücken Sie , um das System-SetupProgramm aufzurufen, und überprüfen Sie die Einstellung System Memory auf dem System-Setup-Hauptbildschirm.
2 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 99. 3 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. VORSICHTSHINWEIS: Fassen Sie das Speichermodul nur am Rand an, wobei Sie darauf achten, die Komponenten auf dem Modul nicht zu berühren. 4 Entfernen Sie das Kühlgehäuse. Siehe „Entfernen des Kühlgehäuses“ auf Seite 114. 5 Schieben Sie die vordere Gehäusebaugruppe vom Gehäuse weg. Siehe „Vordere Gehäusebaugruppe“ auf Seite 116.
Lüfter Das System enthält in einer Lüfterbaugruppe sechs hot-swap-fähige Lüfter, die die Prozessoren, die Erweiterungskarten und die Speichermodule kühlen. ANMERKUNG: Wenn mit einem bestimmten Lüfter ein Problem auftritt, wird die Lüfternummer in der Systemverwaltungssoftware angegeben, wodurch Sie den richtigen Lüfter anhand der Nummern an der Lüfterbaugruppe leicht identifizieren und austauschen können.
Abbildung 3-12.
Installieren eines Lüfters WARNUNG: Das Öffnen und Entfernen der Systemabdeckung bei eingeschaltetem System birgt die Gefahr eines elektrischen Schlags. Üben Sie äußerste Vorsicht, wenn Sie Lüfter entfernen oder installieren. 1 Richten Sie den Anschluss am Lüfter mit dem Anschluss auf der Systemplatine aus. 2 Senken Sie den Lüfter in die Lüfterbaugruppe ab, bis die Sperrklinken einrasten. Siehe Abbildung 3-12. 3 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101.
Abbildung 3-13. Lüfterbaugruppe entfernen und installieren 1 2 3 1 Freigabehebel (2) 3 Aussparungen (2) 2 Lüfterbaugruppe Installieren der Lüfterbaugruppe 1 Richten Sie die Lüfterbaugruppe korrekt zum Gehäuse aus. Siehe Abbildung 3-1. 2 Richten Sie die Schlitze auf den Seiten der Lüfterbaugruppe mit den Haltern am Systemgehäuse aus. Siehe Abbildung 3-13. 3 Setzen Sie die Lüfterbaugruppe im System ein und senken Sie die blauen Freigabehebel ab, um die Baugruppe zu sichern.
4 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 5 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. Interner USB-Speicherstick Ein optionaler USB-Speicherstick im System lässt sich als Startgerät, Sicherheitsschlüssel oder Massenspeichergerät einsetzen. Der USB-Anschluss muss aktiviert sein.
Abbildung 3-14. USB-Speicherstick entfernen und installieren 1 2 1 Anschluss für USB-Speicherstick 2 USB-Speicherstick Interner NIC-Hardwareschlüssel Künftige zusätzliche Funktionsmerkmale für die im System integrierten NICs werden durch Einsetzen eines optionalen NIC-Hardwareschlüssels im Sockel iSCSI KEY auf der Systemplatine aktiviert. Siehe Abbildung 6-1. VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
3 Lokalisieren Sie den ISCSI KEY-Anschluss auf der Systemplatine. Siehe Abbildung 6-1. 4 Setzen Sie den NIC-Hardwareschlüssel in den Anschluss auf der Platine ein. Siehe Abbildung 3-15. Abbildung 3-15. NIC-Hardwareschlüssel installieren 1 2 1 NIC-Hardwareschlüssel 2 ISCSI KEY-Anschluss 5 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 6 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
Erweiterungskarten und Erweiterungskarten-Riser Richtlinien zur Installation von Erweiterungskarten Das System unterstützt bis zu sechs PCIe-Erweiterungskarten der 2. Generation in den Steckplätzen auf der Systemplatine sowie zwei Erweiterungskarten-Riser. Die Position der Erweiterungssteckplätze auf der Systemplatine können Sie Abbildung 6-1 entnehmen und die Position der Erweiterungssteckplätze auf den Erweiterungskarten-Risern können Sie Abbildung 6-4 und Abbildung 6-5 entnehmen.
Tabelle 3-4 enthält Vorschläge für die Installation von Erweiterungskarten hinsichtlich bestmöglicher Kühlung und mechanischer Unterbringung. Die Erweiterungskarten mit der höchsten Priorität sollten als erste installiert werden und dabei die entsprechende Steckplatzpriorität erhalten. Alle anderen Erweiterungskarten sollten nach Kartenpriorität und in der Reihenfolge der Steckplatzpriorität installiert werden. Tabelle 3-4.
Installieren einer Erweiterungskarte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-16. Erweiterungskarte installieren und entfernen 1 2 3 1 Erweiterungskartenverriegelung 3 Erweiterungskartensteckplatz 2 Erweiterungskarte 9 Verbinden Sie die Kabel mit der Erweiterungskarte. 10 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 11 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein.
Entfernen von Erweiterungskarten VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Erweiterungskarten-Riser Die Erweiterungskarten-Riser des Systems unterstützen PCIeErweiterungskarten der 2. Generation. ANMERKUNG: Stellen Sie sicher, dass sowohl Riser 1 als auch Riser 2 installiert sind, bevor Sie das System einschalten. Entfernen des Erweiterungskarten-Risers 1 VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden.
Abbildung 3-17.
Installieren von Erweiterungskarten-Riser 1 1 Richten Sie den Erweiterungskarten-Riser mit dem Schlitz an der RiserFührung und dem Riser-Führungsstift auf der Systemplatine aus. Siehe Abbildung 3-17. 2 Senken Sie den Erweiterungskarten-Riser ab, bis der Stecker vollständig im Anschluss eingesetzt ist. 3 Installieren Sie gegebenenfalls die Speichercontrollerkarte. Siehe „Installieren der integrierten Speichercontrollerkarte“ auf Seite 148. 4 Setzen Sie gegebenenfalls die Erweiterungskarten wieder ein.
Abbildung 3-18.
Installieren von Erweiterungskarten-Riser 2 1 Richten Sie den Erweiterungskarten-Riser mit den Riser-Führungsstiften auf der Systemplatine und dem Schlitz am Gehäuse aus. Siehe Abbildung 3-17. 2 Senken Sie den Erweiterungskarten-Riser ab, bis der Stecker vollständig im Anschluss eingesetzt ist. 3 Setzen Sie gegebenenfalls die Erweiterungskarten wieder ein. Siehe „Installieren einer Erweiterungskarte“ auf Seite 136. 4 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101.
Abbildung 3-19. iDRAC6 Enterprise-Karte (optional) installieren oder entfernen 1 2 3 4 6 5 1 iDRAC6 Enterprise-Karte 2 VFlash-Mediensteckplatz 3 VFlash SD-Karte 4 Halterungsstege (2) 5 Haltelaschen (2) 6 Anschluss für iDRAC6 Enterprise-Karte 5 Schließen Sie gegebenenfalls das Ethernet-Kabel vom iDRAC6 Enterprise-Kartenanschluss auf der Systemrückseite an. Siehe Abbildung 1-3. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101.
Entfernen einer iDRAC6 Enterprise-Karte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Integrierte Speichercontrollerkarte Das System verfügt am Erweiterungskarten-Riser 1 über einen reservierten Erweiterungssteckplatz für eine integrierte SAS- oder PERC-Controllerkarte, die das integrierte Speichersubsystem für die internen Systemfestplatten bereitstellt. Der Controller unterstützt SAS- und SATA-Festplatten und ermöglicht außerdem das Einrichten der Festplatten in RAIDKonfigurationen, je nach Version des Speichercontrollers im System.
Abbildung 3-20.
Installieren der integrierten Speichercontrollerkarte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
VFlash-Medium (optional) Die VFlash-Medienkarte ist eine SD-Karte (Secure Digital), die an der optionalen iDRAC6-Enterprise-Karte in der hinteren Ecke des Systems eingesetzt wird. Installieren einer VFlash-Medienkarte 1 Lokalisieren Sie den VFlash-Mediensteckplatz in der hinteren Ecke des Systems. 2 Führen Sie das SD-Kartenende mit den Kontakten in den Steckplatz ein, wobei die Etikettseite nach oben weist.
5 Ziehen Sie die Sperrklinke am Akkuhalter und heben Sie den Akkuhalter aus den Aussparungen am Gehäuse heraus. Siehe Abbildung 3-21. 6 Ziehen Sie die zwei Haltelaschen des RAID-Akkus vorsichtig nach hinten und heben Sie den RAID-Akku aus dem Halter heraus. Siehe Abbildung 3-21. Abbildung 3-21.
Installieren des RAID-Akkus 1 Setzen Sie den RAID-Akku in den Akkuhalter ein. Siehe Abbildung 3-21. 2 Richten Sie die Laschen am Akkuhalter mit dem Aussparungen am Gehäuse aus. 3 Schieben Sie den Akkuhalter in die entsprechenden Aussparungen, bis er einrastet. Siehe Abbildung 3-21. 4 Verbinden Sie gegebenenfalls das Akkukabel mit dem Anschluss auf der Speicherkarte. 5 Verlegen Sie die Stromversorgungs- und Datenkabel entlang der Systemgehäusewand.
5 Heben Sie die Sperrklinke an, die das interne zweifache SD-Modul an der vorderen Gehäusebaugruppe sichert und heben Sie das Modul aus der Baugruppe. Siehe Abbildung 3-22. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 7 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. Abbildung 3-22.
Installieren des internen zweifachen SD-Moduls VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Prozessoren Das System unterstützt Konfigurationen mit einem, zwei oder vier Prozessoren. Bei Ein- oder Zwei-Prozessor-Konfigurationen werden die Prozessoren in den Sockeln 1 und 2 installiert; die FlexMem-Brücken werden in den Prozessorsockeln 3 und 4 installiert, damit die Prozessoren auf den benachbarten Speichersatz zugreifen können. Weitere Informationen über das Installieren einer FlexMem-Brücke erhalten Sie unter „Installieren einer FlexMem-Brücke“ auf Seite 163.
Entfernen eines Prozessors VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
7 Lösen Sie den anderen Kühlkörper-Entriegelungshebel. 8 Heben Sie den Kühlkörper vorsichtig vom Prozessor ab und legen Sie ihn mit der Oberseite nach unten ab (Wärmeleitpaste nach oben). Abbildung 3-23.
VORSICHTSHINWEIS: Der Prozessor steht im Sockel unter starker mechanischer Spannung. Beachten Sie, dass der Freigabehebel plötzlich hochschnellen kann, wenn er nicht festgehalten wird. 9 Halten Sie Ihren Daumen fest auf dem Freigabehebel des Prozessorsockels und lösen Sie den Hebel aus der verriegelten Position, indem Sie ihn nach unten drücken und unter der Lasche hervorziehen. Schwenken Sie den Freigabehebel um 90 Grad nach oben, bis der Prozessor vom Sockel gelöst ist. Siehe Abbildung 3-24.
Abbildung 3-24. Prozessor entfernen und installieren 1 2 7 6 3 4 5 1 Prozessor 2 Kerben im Prozessor (2) 3 Sockelpassungen (2) 4 Prozessorabdeckung 5 ZIF-Sockel 6 Freigabehebel des Sockels 7 Kontaktstift-1-Markierungen (2) VORSICHTSHINWEIS: Achten Sie darauf, keine Kontaktstifte am ZIF-Sockel zu verbiegen, wenn Sie den Prozessor entfernen. Durch ein Verbiegen der Kontaktstifte kann die Systemplatine dauerhaft beschädigt werden.
11 Heben Sie den Prozessor vorsichtig aus dem Sockel und belassen Sie den Hebel in senkrechter Position, damit der neue Prozessor in den Sockel eingepasst werden kann. Legen Sie den Prozessor nach dem Herausnehmen in einen antistatischen Behälter, um ihn später wieder einzusetzen, einzuschicken oder zeitweilig zu lagern. Berühren Sie nicht die Unterseite des Prozessors. Fassen Sie den Prozessor nur an den Kanten an.
Abbildung 3-25. Abdeckung vom Prozessorsockel entfernen 1 2 1 Sockelabdeckung aus Kunststoff 2 Prozessorsockel 2 Nehmen Sie den Prozessor aus der Verpackung, indem Sie ihn nur an den Kanten halten. Berühren Sie nicht die Unterseite des Prozessors. Gehen Sie vorsichtig mit dem Prozessor um, während Sie ihn mit den Fingern an den seitlichen Rändern halten. Halten Sie Ihre Hand unter den Prozessor, wenn Sie ihn zum System bewegen. 3 Suchen Sie die Kontaktstift-1-Markierung auf dem Systemplatinensockel.
5 Positionieren Sie den Prozessor so über dem Sockel, dass die beiden Kontaktstift-1-Markierungen miteinander ausgerichtet und parallel sind. Siehe Abbildung 3-24. VORSICHTSHINWEIS: Wenden Sie beim Einsetzen des Prozessors keine Kraft an. Wenn der Prozessor korrekt positioniert ist, lässt er sich leicht in den Sockel einsetzen. 6 Richten Sie die Kerben am Prozessor mit den Passungen am ZIFSockel aus. Siehe Abbildung 3-24. 7 Setzen Sie den Prozessor in den Sockel ein.
12 Setzen Sie das Kühlgehäuse ein. Siehe „Installieren des Kühlgehäuses“ auf Seite 115. 13 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 14 Verbinden Sie das System und die Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein. 15 Drücken Sie , um das System-Setup-Programm aufzurufen und überprüfen Sie, ob die Prozessorinformationen mit der neuen Systemkonfiguration übereinstimmen. Siehe „Aufrufen des SystemSetup-Programms“ auf Seite 72.
Installieren einer FlexMem-Brücke VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-26.
Entfernen einer FlexMem-Brücke VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
6 Schließen Sie die Prozessorabdeckung. Siehe Abbildung 3-26. 7 Schwenken Sie den Freigabehebel nach unten, bis er einrastet. Siehe Abbildung 3-26. 8 Installieren Sie den Kühlkörperplatzhalter auf dem leeren Prozessorsockel. Siehe „Prozessoren“ auf Seite 154. 9 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 10 Verbinden Sie das System und die Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein.
Abbildung 3-27. Systembatterie austauschen 1 2 3 1 Positive Seite des Batteriesockels 3 Negative Seite des Batteriesockels 2 Systembatterie 3 Lokalisieren Sie den Batteriesockel. Siehe Abbildung 6-1. 4 Entfernen Sie gegebenenfalls die Speichercontrollerkarte. Siehe „Entfernen der integrierten Speichercontrollerkarte“ auf Seite 146. VORSICHTSHINWEIS: Um Beschädigungen am Batteriesockel zu vermeiden, müssen Sie den Sockel fest unterstützen, wenn Sie eine Batterie installieren oder entfernen.
7 Wenn Sie eine neue Systembatterie installieren, unterstützen Sie den Batteriesockel, indem Sie fest auf die positive Seite des Sockels drücken. 8 Halten Sie die Batterie mit dem Pluspol (+) nach oben und schieben Sie sie unter die Haltklammern auf der Plus-Seite des Sockels. 9 Drücken Sie die Batterie gerade nach unten in den Sockel, bis sie einrastet. 10 Installieren Sie gegebenenfalls die Speichercontrollerkarte. Siehe „Installieren der integrierten Speichercontrollerkarte“ auf Seite 148.
3 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. VORSICHTSHINWEIS: Um Schäden an den Laufwerken und der Rückwandplatine zu vermeiden, müssen Sie die Festplatten aus dem System entfernen, bevor Sie die Rückwandplatine entfernen. VORSICHTSHINWEIS: Die Nummern der einzelnen Festplatten müssen notiert und vor dem Entfernen auf den Festplatten vermerkt werden, damit sie an den gleichen Positionen wieder eingesetzt werden können. 4 Entfernen Sie das Kühlgehäuse.
Abbildung 3-28.
Installieren der SAS-Rückwandplatine 1 Richten Sie die Aussparungen an der SAS-Rückwandplatine mit den Laschen an der vorderen Gehäusebaugruppe aus. 2 Schieben Sie die SAS-Rückwandplatine nach unten, bis die blauen Sperrklinken einrasten. 3 Verbinden Sie das SAS-A-Kabel mit dem Anschluss SAS A und das SAS-B-Kabel mit dem Anschluss SAS B auf der Rückwandplatine. Siehe Abbildung 3-28. 4 Verbinden Sie das Stromversorgungskabel mit der Rückwandplatine. Siehe Abbildung 3-28.
Stromverteilungsplatine Entfernen der Stromverteilungsplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Abbildung 3-29.
Installieren der Stromverteilungsplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Bedienfeldbaugruppe Entfernen des Bedienfeldanzeigemoduls VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
4 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 5 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und alle angeschlossenen Peripheriegeräte ein. 6 Bringen Sie gegebenenfalls die Frontverkleidung an. Siehe „Installieren der Frontverkleidung“ auf Seite 99. Abbildung 3-30.
Entfernen der Bedienfeldplatine VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
5 Verbinden Sie alle Kabel mit der Bediendfeldplatine. 6 Verlegen Sie gegebenenfalls die Stromversorgungs- und Datenkabel entlang der Gehäusewand. Siehe Schritt 2 und Schritt 3 von „Verschieben der vorderen Gehäusebaugruppe“ auf Seite 116. 7 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 8 Bringen Sie gegebenenfalls die Frontverkleidung an. Siehe „Installieren der Frontverkleidung“ auf Seite 99.
1 Schalten Sie das System und die angeschlossenen Peripheriegeräte aus und trennen Sie das System vom Netzstrom. 2 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. 3 Entfernen Sie das Kühlgehäuse. Siehe „Entfernen des Kühlgehäuses“ auf Seite 114. 4 Entfernen Sie gegebenenfalls die Frontverkleidung. Siehe „Entfernen der Frontverkleidung“ auf Seite 99. 5 Schieben Sie die vordere Gehäusebaugruppe vom System weg. Siehe „Vordere Gehäusebaugruppe“ auf Seite 116. 6 Entfernen Sie die Kabelklemme.
16 Trennen Sie die Kabel von der Systemplatinenbaugruppe, der SASRückwandplatine, der Bedienfeldplatine und dem optischen Laufwerk. 17 Heben Sie die Sperrklinke an der Hochleistungsverbindung leicht an, um die Freigabehebel zu entsperren. Siehe Abbildung 3-31. 18 Drücken Sie die Freigabehebel um einen Winkel von 90 Grad vom Anschluss weg, um die Prozessorplatine von der E/A-Platine zu trennen. Siehe Abbildung 3-31.
Abbildung 3-31.
Installieren der Systemplatinenbaugruppe 1 Entnehmen Sie die neue Systemplatine der Verpackung. 2 Halten Sie die E/A-Platine an einer Kante und am Freigabestift und senken Sie die Platine in das Gehäuse ab. 3 Positionieren Sie die E/A-Platine auf dem Gehäuseboden, bis sie völlig flach aufliegt. 4 Schieben Sie die E/A-Platine in Richtung Systemrückseite und führen Sie die Stecker in die Aussparungen auf der Gehäuserückseite ein.
12 Installieren Sie den RAID-Akkuhalter. Siehe Abbildung 3-21. 13 Ersetzen Sie den RAID-Akku. Siehe „Installieren des RAID-Akkus“ auf Seite 151. 14 Installieren Sie die Kabelklemme. Siehe Abbildung 3-10. 15 Installieren Sie die Lüfterbaugruppe. Siehe „Installieren der Lüfterbaugruppe“ auf Seite 130. 16 Installieren Sie gegebenenfalls den NIC-Hardwareschlüssel auf der Systemplatine. Siehe „Interner NIC-Hardwareschlüssel“ auf Seite 132. 17 Installieren Sie die Erweiterungskarten-Riser.
Installieren von Systemkomponenten
Fehlerbehebung am System Sicherheit geht vor – für Sie und Ihr System VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei externen Verbindungen Stellen Sie sicher, dass alle externen Kabel fest mit den externen Anschlüssen des Systems verbunden sind, bevor Sie mit der Fehlerbehebung von externen Geräten beginnen. Die Anschlüsse auf der Vorder- und Rückseite des Systems sind in Abbildung 1-1 und Abbildung 1-3 dargestellt. Fehlerbehebung beim Grafiksubsystem 1 Überprüfen Sie die Systemanschlüsse und die Stromversorgung des Bildschirms.
c Tauschen Sie die Tastatur/Maus durch eine andere, funktionierende Tastatur/Maus aus. Wenn sich das Problem auf diese Weise lösen lässt, ersetzen Sie die defekte Tastatur/Maus. Wenn das Problem nicht gelöst wurde, fahren Sie mit dem nächsten Schritt fort und beginnen Sie mit der Fehlerbehebung der anderen USB-Geräte am System. 2 Schalten Sie alle angeschlossenen USB-Geräte aus und trennen Sie sie vom System.
Fehlerbehebung bei einem seriellen E/A-Gerät 1 Schalten Sie das System und die an die serielle Schnittstelle angeschlossenen Peripheriegeräte aus. 2 Ersetzen Sie das serielle Schnittstellenkabel durch ein bekanntermaßen funktionierendes und schalten Sie das System und das serielle Gerät ein. Wenn sich das Problem auf diese Weise lösen lässt, muss das Schnittstellenkabel ersetzt werden. 3 Schalten Sie das System und das serielle Gerät aus und tauschen Sie das Gerät gegen ein vergleichbares Gerät aus.
4 Stellen Sie sicher, dass die entsprechenden Treiber installiert und die Protokolle eingebunden sind. Weitere Informationen finden Sie in der Dokumentation zum NIC. 5 Rufen Sie das System-Setup-Programm auf und stellen Sie sicher, dass die NIC-Ports aktiviert sind. Siehe „Bildschirm Integrated Devices (Integrierte Geräte)“ auf Seite 80. 6 Stellen Sie sicher, dass alle NICs, Hubs und Switches im Netzwerk auf die gleiche Datenübertragungsrate und Duplexeinstellung gesetzt sind.
• Erweiterungskarten und beide Erweiterungskarten-Riser • Integrierter Speichercontroller • iDRAC6 Enterprise-Karte • Netzteile • Prozessoren und Kühlkörper 4 Lassen Sie das System gründlich trocknen (mindestens 24 Stunden). 5 Setzen Sie die in Schritt 3 entfernten Komponenten wieder ein. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 7 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und die angeschlossenen Peripheriegeräte ein.
3 Stellen Sie sicher, dass die folgenden Komponenten ordnungsgemäß installiert sind: • Festplattenlaufwerke • Lüfterbaugruppe • SD-Karten • USB-Speicherstick • NIC-Hardwareschlüssel • Internes zweifaches SD-Modul • Erweiterungskarten und beide Erweiterungskarten-Riser • Integrierter Speichercontroller • iDRAC6 Enterprise-Karte • Netzteile • Prozessoren und Kühlkörper 4 Stellen Sie sicher, dass alle Kabel ordnungsgemäß angeschlossen sind. 5 Schließen Sie das System.
3 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie es ein. 4 Rufen Sie das System-Setup-Programm auf. Wenn Uhrzeit und Datum im System-Setup-Programm nicht korrekt angezeigt sind, muss die Batterie ausgetauscht werden. Siehe „Austauschen der Systembatterie“ auf Seite 166. ANMERKUNG: Die Systemzeit kann durch bestimmte Software beschleunigt oder verlangsamt werden.
Fehlerbehebung bei der Systemkühlung VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei einem Lüfter VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung beim Systemspeicher VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
6 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. 7 Überprüfen Sie die korrekte Bestückung der Speicherkanäle. Siehe „Richtlinien zur Installation von Speichermodulen“ auf Seite 119. 8 Setzen Sie die Speichermodule wieder in die Sockel ein. Siehe „Installieren von Speichermodulen“ auf Seite 123. 9 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101.
Fehlerbehebung bei einem internen USB-Stick VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
Fehlerbehebung bei einer SD-Karte VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
9 Schalten Sie das System und die angeschlossenen Peripheriegeräte ein und überprüfen Sie, ob die SD-Karte funktioniert. 10 Setzen Sie eine andere, funktionierende SD-Karte ein. 11 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 12 Schalten Sie das System und die angeschlossenen Peripheriegeräte ein und überprüfen Sie, ob die SD-Karte funktioniert. Wenn das Problem nicht behoben wird, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221.
9 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 10 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und die angeschlossenen Peripheriegeräte ein. Wenn das Problem nicht behoben wird, lesen Sie „Wie Sie Hilfe bekommen“ auf Seite 221. Fehlerbehebung bei einem Bandsicherungsgerät ANMERKUNG: Lesen Sie zur Fehlerbehebung bei einem Bandlaufwerk die entsprechende Dokumentation unter support.dell.
Fehlerbehebung bei einem Festplattenlaufwerk VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
5 Starten Sie das System neu, rufen Sie das System-Setup-Programm auf und überprüfen Sie, ob der Controller aktiviert ist und die Laufwerke im System-Setup-Programm angezeigt werden. Siehe „Verwenden des SystemSetup-Programms und des UEFI-Boot-Managers“ auf Seite 71. Wenn das Problem weiterhin besteht, lesen Sie „Fehlerbehebung bei einem Speichercontroller“ auf Seite 202.
6 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. 7 Überprüfen Sie die Controllerkarte auf korrekten Sitz und Anschluss auf der Systemplatine. Siehe „Integrierte Speichercontrollerkarte“ auf Seite 146. 8 Wenn es sich um einen PERC-Controller mit Akku-Cache handelt, stellen Sie sicher, dass der RAID-Akku richtig angeschlossen ist und gegebenenfalls das Speichermodul auf der PERC-Karte ordnungsgemäß eingesetzt ist.
3 Öffnen Sie das System. Siehe „Öffnen des Systems“ auf Seite 100. 4 Überprüfen Sie, ob die installierten Erweiterungskarten den Installationsrichtlinien für Erweiterungskarten entsprechen. Siehe „Richtlinien zur Installation von Erweiterungskarten“ auf Seite 134. 5 Überprüfen Sie jede Erweiterungskarte auf korrekten Sitz und Anschluss. Siehe „Installieren einer Erweiterungskarte“ auf Seite 136. 6 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101.
Fehlerbehebung bei den Prozessoren VORSICHTSHINWEIS: Viele Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Fehlerbehebungsmaßnahmen oder einfache Reparaturen sollten Sie nur dann selbst vornehmen, wenn dies mit der Produktdokumentation im Einklang steht oder Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsversuche werden nicht durch die Garantie abgedeckt.
13 Entfernen Sie alle Prozessoren außer Prozessor 1 und Prozessor 2. Siehe „Entfernen eines Prozessors“ auf Seite 155. 14 Installieren Sie die Lüfterbaugruppe. Siehe „Installieren der Lüfterbaugruppe“ auf Seite 130. 15 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 16 Verbinden Sie das System wieder mit dem Netzstrom und schalten Sie das System und die angeschlossenen Peripheriegeräte ein. 17 Führen Sie die entsprechende Online-Diagnose durch.
Ausführen der Systemdiagnose Bei Problemen mit dem System sollten Sie eine Diagnose durchführen, bevor Sie technische Unterstützung anfordern. Der Zweck der Diagnose ist es, die Hardware des Systems ohne zusätzliche Ausrüstung und ohne das Risiko eines Datenverlusts zu überprüfen. Wenn Sie ein Problem nicht selbst beheben können, können Service- und Supportmitarbeiter die Diagnoseergebnisse zur Lösung des Problems verwenden.
• Laufende Tests bei Auftreten eines Fehlers unterbrechen oder die Tests ganz abbrechen, wenn eine einstellbare Obergrenze für Fehler erreicht wird • Hilfemeldungen mit kurzer Beschreibung aller Tests und ihrer Parameter anzeigen • Statusmeldungen ansehen, die zeigen, ob Tests erfolgreich abgeschlossen wurden • Fehlermeldungen über Probleme während des Testvorgangs anzeigen Einsatzbereich der integrierten Systemdiagnose Wenn eine Hauptkomponente oder ein Gerät des Systems nicht ordnungsgemäß funktio
Testoptionen der Systemdiagnose Klicken Sie auf die Testoption im Fenster Main Menu (Hauptmenü). Testoption Funktion Express Test Führt eine schnelle Überprüfung des Systems durch. Bei dieser Option werden Gerätetests durchgeführt, bei denen keine Eingabe durch den Benutzer erforderlich ist. Extended Test Führt eine genauere Überprüfung des Systems durch. Dieser Test kann eine Stunde oder länger dauern. Custom Test Testet ein bestimmtes Gerät. Information Zeigt Testergebnisse an.
Auswählen von Diagnoseoptionen Die Testoptionen für ein Gerät können Sie im Bereich Diagnostics Options einstellen. • Non-Interactive Tests Only – Führt nur Tests durch, die keine Benutzereingaben erfordern. • Quick Tests Only – Führt nur die schnell durchführbaren Tests am Gerät durch. • Show Ending Timestamp – Schreibt die Zeiten der Tests in die Protokolldatei. • Test Iterations – Legt fest, wie oft der Test durchgeführt wird.
Jumper, Schalter und Anschlüsse Jumper auf der Systemplatine Informationen zum Deaktivieren eines Kennworts durch Zurücksetzen des Kennwort-Jumpers finden Sie im Abschnitt „Deaktivieren eines verlorenen Kennworts“ auf Seite 219. Tabelle 6-1.
Anschlüsse auf der Systemplatine Abbildung 6-1.
Tabelle 6-2.
Element Anschluss Beschreibung 17 D7 Speichermodulsockel D7 D3 Speichermodulsockel D3 (weißer Auswurfhebel) D5 Speichermodulsockel D5 D1 Speichermodulsockel D1 (weißer Auswurfhebel) C2 Speichermodulsockel C2 (weißer Auswurfhebel) C6 Speichermodulsockel C6 C4 Speichermodulsockel C4 (weißer Auswurfhebel) C8 Speichermodulsockel C8 A7 Speichermodulsockel A7 A3 Speichermodulsockel A3 (weißer Auswurfhebel) A5 Speichermodulsockel A5 A1 Speichermodulsockel A1 (weißer Auswurfhebel) 20 BP
Element Anschluss Beschreibung 29 FAN4 Systemlüfter 4 30 PWR_CONN Stromversorgungsanschluss 31 CTRL_PNL Anschluss für Bedienfeld 32 Left PCIE_G2_X16 Anschluss für Erweiterungskarten-Riser 2 SAS-Rückwandplatinenanschlüsse Abbildung 6-2.
Anschlüsse für Stromverteilungsplatine Abbildung 6-3.
Komponenten und PCIe-Busse der Erweiterungskarten-Steckkarte Abbildung 6-4.
Abbildung 6-5.
Deaktivieren eines verlorenen Kennworts Zu den Sicherheitsfunktionen der Systemsoftware gehören ein Systemkennwort und ein Setup-Kennwort. Diese werden ausführlich unter „Verwenden des System-Setup-Programms und des UEFI-Boot-Managers“ auf Seite 71 beschrieben. Der Kennwort-Jumper aktiviert bzw. deaktiviert diese Kennwortfunktionen und löscht alle derzeit benutzten Kennwörter.
8 Überbrücken Sie den Kennwort-Jumper wieder. 9 Schließen Sie das System. Siehe „Schließen des Systems“ auf Seite 101. 10 Verbinden Sie das System und die Peripheriegeräte wieder mit dem Netzstrom und schalten Sie sie ein. 11 Weisen Sie ein neues System- und/oder Setup-Kennwort zu. Wie Sie im System-Setup-Programm ein neues Kennwort festlegen, erfahren Sie im Abschnitt „Zuweisen eines Systemkennworts“ auf Seite 90.
Wie Sie Hilfe bekommen Kontaktaufnahme mit Dell Kunden in den USA können die Nummer 800-WWW-DELL (800-999-3355) anrufen. ANMERKUNG: Wenn Sie nicht mit dem Internet verbunden sind, finden Sie die Kontaktinformationen auf der Rechnung, dem Lieferschein oder im Produktkatalog von Dell. Dell bietet verschiedene Optionen für Support und Service online oder per Telefon. Die Verfügbarkeit ist je nach Land und Produkt unterschiedlich, und bestimmte Dienstleistungen sind in Ihrer Region eventuell nicht erhältlich.
Wie Sie Hilfe bekommen
Stichwortverzeichnis A Akku Fehlerbehebung beim RAID-Kartenakku, 202 Anschlüsse Bildschirm, 14, 23 USB, 14, 23 Anweisungen nur für Service Systemplatine, 178 Anzeigen NIC, 25 Stromversorgung, 14, 26 Vorderseite, 14 Arbeitsspeicher Fehlerbehebung, 195 Beschädigte Systeme Fehlerbehebung, 190 Betriebsanzeigen, 14, 26 Bildschirm Anschlüsse auf der Vorderseite, 14 C CD/DVD-Laufwerk Siehe Optisches Laufwerk CD-Laufwerk Fehlerbehebung, 199 D Austauschen Netzteil, 113 Systembatterie, 166 Dell Kontaktaufnahme,
E Empfohlene Werkzeuge, 97 Entfernen Erweiterungskarte, 138 Festplatten, 104 Festplattenlaufwerk aus einem Laufwerkträger, 106 FlexMem-Brücke, 165 Frontverkleidung, 99 Laufwerksplatzhalter, 102 Netzteil, 111 Netzteilplatzhalter, 113 Prozessor, 155 SAS-Controller, 146 SAS-Rückwandplatine, 168 Speichermodule, 125 Systemplatine, 178 Entfernen der Prozessorplatine, 178 Erweiterungskarte Fehlerbehebung, 203 Erweiterungskarten Entfernen, 138 Installieren, 136 SAS-Controller, 146 Erweiterungssteckplätze, 134 Fehl
G Garantie, 70 Internes zweifaches SD-Modul, 151 Gehäuseeingriffschalter, 218 Grafik Fehlerbehebung, 186 H Hot-plug Festplattenlaufwerke, 102 I iDRAC-Karte Installieren, 143 iDRAC-Konfigurationsprogramm, 95 Installation Netzteilplatzhalter, 113 Installieren Erweiterungskarte, 136 Festplattenträger, 105 FlexMem-Brücke, 163 Frontverkleidung, 99 iDRAC-Karte, 143 Laufwerksplatzhalter, 103 Optisches Laufwerk, 107 Prozessor, 159 SAS-Controller, 148 SAS-Rückwandplatine, 171 Speichermodule, 123 Systemplatinenba
Merkmale des vorderen Bedienfelds, 14 P Mikroprozessor Siehe Prozessor.
SAS-Rückwandplatine Entfernen, 168 Installieren, 171 Schützen des Systems, 85, 91 SD-Karte Fehlerbehebung, 197-198 Setup-Kennwort, 93 Sicherheit, 185 Speichermodule (DIMMs) Entfernen, 125 Installieren, 123 Konfigurieren, 119 UDIMM-Konfigurationen, 135 Speicherstickanschluss (USB), 131 Start Zugriff auf Systemfunktionen, 13 Steckplätze Siehe Erweiterungssteckplätze Support Kontaktaufnahme mit Dell, 221 System-Setup Optionen, 74 System-Setup-Bildschirme Hauptbildschirm, 74 System-Setup-Programm Aufrufen, 72
Aufrufen, 87 Bildschirm System Utilities (Systemdienstprogramme), 89 Bildschirm UEFI Boot Settings (UEFI-Starteinstellungen), 88 Hauptbildschirm, 88 Upgrades Prozessor, 154 USB Anschlüsse auf der Vorderseite, 14 Interner Anschluss für Speicherstick, 131 USB-Stick Fehlerbehebung, 197-198 228 Stichwortverzeichnis V Verkabelung Optisches Laufwerk, 107 Vordere Gehäusebaugruppe, 116 W Warnmeldungen, 69