Dell™ PowerEdge™ R815 Donanım Kullanıcı El Kitabı Tescilli Model: E05S Tescilli Tip: E05S001
Notlar, Dikkat Edilecek Noktalar ve Uyarılar NOT: NOT, bilgisayarınızdan daha iyi şekilde yararlanmanıza yardımcı olacak önemli bilgiler verir. DİKKAT: DİKKAT, yönergelere uyulmadığında donanımın zarar görebileceğini veya veri kaybı olabileceğini belirtir. UYARI: UYARI, meydana gelebilecek olası maddi hasar, kişisel yaralanma veya ölüm tehlikesi anlamına gelir. ____________________ Bu belgedeki bilgiler önceden bildirilmeksizin değiştirilebilir. © 2010 Dell Inc. Tüm hakları saklıdır. Dell Inc.
İçerik 1 Sisteminiz Hakkında . . . . . . . . . . . . . Başlangıç Sırasında Sistem Özelliklerin Erişme . . . . . . . . . . . . . . . . . . 13 . . . . . . . 14 . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . . . . . . . . . 17 . . . . . . . . . . . . . . . . . 18 . . . . . . . . . . . . . . . . 19 Ön Panel Özellikleri ve Göstergeleri LCD Paneli Özellikleri Ana Ekran 13 Kurulum Menüsü Görünüm Menüsü Sabit Sürücü Gösterge Modelleri . . . . . . . . .
Uyarı İletileri . . . . . . . . . . . . . . . . . . . . . . İhtiyaç Duyabileceğiniz Diğer Bilgiler 2 Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma . . . . . . . . . . . . . . . . . . . Sistem Önyükleme Modunu Seçme. . . . . . . . Sistem Kurulumu Programına Girme . Hata İletilerine Yapılacak İşlemler 59 . . . . . . 60 60 60 . . . . . . . . . . . 61 . . . . . . . . . . . . . . . . . . . . . 61 . . . . . . . . . . . . . .
Sistem ve Kurulum Şifresi Özellikleri . . . . . . 73 Sistem Şifresini Kullanma . . . . . . . . . . . . 73 Kurulum Şifresini Kullanma . . . . . . . . . . . 75 . . . . . . . . . . . . . 76 Yerleşik Sistem Yönetimi . iDRAC6 Yapılandırma Yardımcı Programı . iDRAC6 Yapılandırma Yardımcı Programı'na Girme . . . . . . . . . . . 77 . . . . . . . . 77 3 Sistem Bileşenlerinin Montajı . 79 . . . . . . . . . . . . . . . . . . . 79 . . . . . . . . . . . . . . . . . . . .
Optik Sürücü . . . . . . . . . . . . . . . . . . . . . . Optik Sürücüyü Çıkarma . . . . . . . . . . . . . 89 . . . . . . . . . . . . . . . 90 . . . . . . . . . . . . . . . . . . . . 91 Optik Sürücü Takma Güç Kaynakları Güç Kaynağını Çıkarma . Güç Kaynağı Takma . . . . . . . . . . . . 92 . . . . . . . . . . . . . . . 93 . . . . . . . . . . 93 . . . . . . . . . . . 93 . . . . . . . . . . . . . . . . . . . 94 Boş Güç Kaynağını Çıkarma Boş Güç Kaynağını Takma Soğutma Örtüsü . . . . . . . .
Genişletme Kartları ve Genişletme Kartı Yükselticileri . . . . . . . . . . . . . . . . . 115 . . . . 115 . . . . . . . . . . . 117 Genişletme Kartı Takma Yönergeleri Genişletme Kartı Takma . Genişletme Kartını Çıkarma . . . . . . . . . Genişletme Kartı Yükselticisi 1'i Çıkarma . Genişletme Kartı Yükselticisi 1'i Takma . 119 . . 120 . . . 122 Genişletme Kartı Yükselticisi 2'yi Çıkarma . . 122 . . . 124 . . . . 124 Tümleşik Depolama Denetleyicisi Kartını Çıkarma . . . . . . . . . . . .
Sistem Pili . . . . . . . . . . . . . . . . . . . . . . 140 . . . . . . . . . . . . 140 . . . . . . . . . . . . . . . . . . 142 Sistem Pilini Değiştirme SAS Arka Paneli . SAS Arka Panelini Sökme . . . . . . . . . . . 142 . . . . . . . . . . . 144 . . . . . . . . . . . . . . . . . 145 SAS Arka Panelini Takma Güç Dağıtım Kartı . Güç Dağıtım Kartını Çıkarma . . . . . . . . . Güç Dağıtım Kartını Değiştirme. . . . . . . . 147 . . . . . . . . . . . . . .
Sorun Giderme - Sistemin Islanması . . . . . . 163 . . . 164 . . . . . . . . . . . 165 . . . . . . . . 165 . . . . . . . . . . . . . 166 . . . . . . . . . 166 Sorun Giderme - Sistemin Hasar Görmesi Sorun Giderme - Sistem Pili Sorun Giderme - Güç Kaynakları Sorun Giderme - Sistem Soğutması Sorunları . . . Sorun Giderme - Pervaneler Sorun Giderme - Sistem Belleği . . . . . . . . . 167 . . . . . 169 . . . . . . . . . . . . . 170 Sorun Giderme - Optik Sürücü . . . . . . . . .
5 Sistem Tanılama Araçlarını Çalıştırma . . . . . . . . . . . . Çevrimiçi Tanılama Araçlarını Kullanma . . . . 179 . . . . . . 180 . . . . . . . . . . . 180 . . . . . . . . . . . . . 181 Yerleşik Sistem Tanılama Özellikleri Yerleşik Sistem Tanılama Araçlarını Kullanma Zamanı Yerleşik Sistem Tanılama Araçlarını Çalıştırma . . . Sistem Tanılama Araçları Sınama Seçenekleri . . . . . . . . . . . . . . . . . . . . . . 181 . . . . . 182 . . . . . . . . . 182 . . . 182 . . . . .
7 Yardım Alma . . . . . . . . . . . . . . . . . . . Dell'e Başvurma Dizin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
İçerik
Sisteminiz Hakkında Başlangıç Sırasında Sistem Özelliklerin Erişme Aşağıdaki tuş vuruşları başlangıç sırasında sistem özelliklerine erişmeyi sağlar. Tuş Vuruşu Tanım Sistem Kurulumu programına girer. Bkz. “Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma” sayfa 59. Yaşam Döngüsü Denetleyicisini açan Sistem Hizmetlerine girer. Yaşam Döngüsü Denetleyicisi tümleşik sistem tanı araçları gibi yardımcı programlara erişmenizi sağlar. Daha fazla bilgi için support.dell.
Ön Panel Özellikleri ve Göstergeleri Şekil 1-1. Ön Panel Özellikleri ve Göstergeleri 1 2 3 4 5 6 Öğe Gösterge, Düğme veya Konnektör 1 Açma göstergesi, güç düğmesi 7 8 Simge 9 10 Tanım Açma göstergesi sistem gücü açık olduğunda yanar. Güç düğmesi sisteme verilen DC güç kaynağı çıkışını denetler. Sistem çerçevesi takılı olduğunda, güç düğmesine erişilemez.
Öğe Gösterge, Düğme veya Konnektör 2 NMI düğmesi Simge Tanım Belirli işletim sistemleri kullanıldığında yazılım veya aygıt sürücüsü hatalarında sorun giderme için kullanılır. Bu düğmeye bir atacın ucu ile basılabilir. Bu düğmeyi yalnızca nitelikli destek personeli veya işletim sisteminin belgeleri tarafından talimat verilirse kullanın. 3 USB konnektörleri (2) USB aygıtlarını sisteme bağlayın. Bağlantı noktaları USB 2.0 uyumludur. 4 Video konnektörü Sisteme bir monitörü bağlar.
Öğe Gösterge, Düğme veya Konnektör 9 Optik sürücü (isteğe bağlı) Simge Tanım Bir adet isteğe bağlı ince SATA DVDROM sürücü veya DVD-RW sürücü. NOT: DVD aygıtları yalnızca veri içindir. 10 Sabit sürücüler Altı adede kadar 2,5 inç, harici çalışırken takılabilir SAS, SATA veya SSD sabit sürücü. LCD Paneli Özellikleri Sistemin LCD paneli, sistemin düzgün çalıştığını veya sisteme dikkat edilmesi gerektiğini göstermek için sistem bilgisi ve durumu ile hata iletilerini gösterir.
Öğe Düğmeler Tanım 1 Sol İmleci tek adımlar artışlarla geriye doğru hareket ettirir. 2 Seç İmleç tarafından vurgulanan menü öğesini seçer. 3 Sağ İmleci tek adımlar artışlarla ileriye doğru hareket ettirir. İleti kaydırma sırasında: • Kaydırma hızını artırmak için bir kez basın. • Durdurmak için tekrar basın. • Varsayılan kaydırma hızına geri dönmek için tekrar basın. • Döngüyü yinelemek için tekrar basın.
Kurulum Menüsü NOT: Kurulum menüsünden bir seçenek seçtiğinizde, sonraki işleme geçmeden önce seçeneği onaylamalısınız. Seçenek Tanım DRAC Ağ modunu yapılandırmak için DHCP veya Statik IP'yi seçin. Statik IP seçilirse, mevcut alanlar IP, Alt Ağ (Sub) ve Ağ Geçidi (Gtw) olur. DNS'i etkinleştirmek, DNS sunucularının IP adreslerini görüntülemek ve ayarlamak için DNS'i Ayarla tseçeneğini seçin. İki ayrı DNS girişi mevcuttur, böylece bir birincil bir de ikincil DNS sunucusu yapılandırılabilir.
Görünüm Menüsü Seçenek Tanım DRAC IP iDRAC6 için IPv4 veya IPv6 adreslerini gösterir. Adresler DNS (Birincil ve İkincil), Ağ Geçidi, IP ve Alt Ağ'ı (IPv6'da Alt Ağ yoktur) içerir. MAC DRAC, iSCSIn, veya NETn'e ait MAC adreslerini gösterir. Ad Sisteme ait Ana Makine, Model veya Kullanıcı Dizesi adını gösterir. Sayı Sisteme ait Varlık etiketini veya Servis etiketini gösterir. Güç Sistemin güç çıkışını BTU/saat veya Watt olarak gösterir.
Sürücü Durumu Gösterge Modeli (Yalnızca RAID) Koşul Saniyede iki kez yeşil renkte yanıp sönüyor Sürücü tanımlanıyor/çıkarmaya hazırlanıyor Kapalı Sürücü takmaya veya çıkarmaya hazır NOT: Sistem gücü verildikten sonra tüm sabit sürücüler başlatılana kadar sürücü durumu göstergesi kapalı kalır. Bu süre zarfında sürücüler takmaya veya çıkarmaya hazır değildir.
Öğe Gösterge, Düğme veya Konnektör Simge Tanım 1 PCIe yuva 1 PCI Express (2. Nesil) x8 bağlantı genişletme yuvası (24,13 cm [9,5 inç] uzunlukta). 2 PCIe yuva 2 PCI Express (2. Nesil) x4 bağlantı genişletme yuvası (standart yükseklik desteğine sahip düşük profilli 24,13 cm [9,5 inç] maksimum uzunlukta). 3 PCIe yuva 3 PCI Express (2. Nesil) x8 bağlantı genişletme yuvası (düşük profilli 24,13 cm [9,5 inç] uzunlukta). 4 PCIe yuva 4 PCI Express (2.
Öğe Gösterge, Düğme veya Konnektör Simge Tanım 11 Ethernet konnektörleri (4) Tümleşik 10/100/1000 NIC konnektörleri. 12 USB konnektörleri (4) USB aygıtlarını sisteme bağlayın. Bağlantı noktaları USB 2.0 uyumludur. 13 Video konnektörü Sisteme bir monitörü bağlar. 14 Seri bağlantı konnektörü Sisteme seri bir cihazı bağlar. 15 VFlash ortam yuvası (isteğe bağlı) İsteğe bağlı iDRAC6 Enterprise kartı için harici bir SD bellek kartı bağlar.
NIC Gösterge Kodları 1 1 bağlantı göstergesi 2 2 etkinlik göstergesi Gösterge Gösterge Kodu Bağlantı ve etkinlik göstergeleri kapalı NIC ağa bağlı değil. Bağlantı göstergesi yeşil NIC, geçerli bir ağa 1000 Mbps'de bağlı. Bağlantı göstergesi sarı NIC, geçerli bir ağa 10 veya 100 Mbps'de bağlı. Etkinlik göstergesi Ağ verileri gönderiliyor veya alınıyor.
Güç Göstergesi Kodları Güç kaynaklarında gücün mevcut olup olmadığını veya bir güç arızası meydana gelip gelmediğini gösteren göstergeler bulunur. • Yanmıyor: AC güç bağlı değil. • Yeşil: Bekleme modunda, yeşil bir ışık geçerli bir AC kaynağının güç kaynağına bağlı olduğunu ve güç kaynağının çalıştığını gösterir. Sistem açıkken, yeşil bir ışık aynı zamanda güç kaynağının sisteme DC güç sağladığını da gösterir. • Sarı: Güç kaynağında sorun olduğunu gösterir. Şekil 1-4.
LCD Durum İletileri LCD iletileri, Sistem Olay Günlüğünde (SEL) kaydedilen olaylarla ilgili kısa metin iletilerinden oluşur. SEL ve sistem yönetim ayarlarını yapılandırma hakkında bilgi için, bkz. systems management software belgeleri. NOT: Sisteminiz önyükleme yapamazsa, Sistem Kimliği düğmesine LCD'de bir hata kodu görünene kadar en az 5 saniye basın. Kodu kaydedin, ardından bkz. “Yardım Alma” sayfa 195. Durum İletilerini Görüntüleme Bir sistem hatası oluşursa, LCD ekranı sarıya dönüşür.
Tablo 1-1. LCD Durum İletileri Nedenler Düzeltici İşlemler E1000 Hatasız voltaj hatası. Destek birimine başvurun. Kritik arıza olaylarında sistem olay günlüğünü inceleyin. Sisteme verilen AC gücü 10 saniyeliğine kesip sistemi yeniden başlatın. E1114 Ortam sıcaklığı izin verilen aralığı aşıyor. Ortam sıcaklığı izin verilen Bkz. “Sorun Giderme aralığın dışındaki bir noktaya Sistem Soğutması ulaşmıştır. Sorunları” sayfa 166. E1116 Bellek devre dışı, sıcaklık aralığın üzerinde. AC güç dönüşümü yapın.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin E1216 3,3 V Regülatör arızası. PCIe kartlarını yeniden yerleştirin. Nedenler Düzeltici İşlemler 3,3 V voltaj regülatörü arızalanmıştır. PCIe genişletme kartlarını çıkarın ve yeniden yerleştirin. Sorun devam ederse, bkz. “Sorun Giderme - Genişletme Kartları” sayfa 175. E1219 Disk Arka Depolama arka paneli voltaj Paneli güç regülatörü arızalanmıştır. arızası. Arka Panel güç kablosunu kontrol edin. Arka panel güç kablosunu çıkarıp yeniden takın.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin Nedenler Düzeltici İşlemler E1310 Pervane ## Belirtilen pervanenin RPM'si Bkz. “Sorun Giderme RPM'si tasarlanan çalışma aralığının Sistem Soğutması aralığı dışındadır. Sorunları” sayfa 166. aşıyor. Pervaneyi kontrol edin. E1313 Pervane yedekliliği kaybedildi. Pervaneleri kontrol edin. Sistem artık pervane yedekli değildir. Başka bir pervane arızası sistemi aşırı ısınma riskine atacaktır. Ek kaydırma iletileri için LCD'yi kontrol edin. Bkz.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin E1418 CPU # algılanmadı. CPU'nun düzgün yerleştirildi ğinden emin olun. Nedenler Düzeltici İşlemler Belirtilen işlemci eksik veya arızalıdır ya da sistem yapılandırması desteklenmemektedir. Belirtilen işlemcinin düzgün takıldığından emin olun. Bkz. “Sorun Giderme - İşlemciler” sayfa 177. E141C Desteklenmeye İşlemcilerin yapılandırması n CPU desteklenmiyordur. yapılandırmas ı. CPU veya BIOS düzeltmesini kontrol edin. E141F CPU # protokol hatası.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin Nedenler Düzeltici İşlemler E1610 Güç Kaynağı # Belirtilen güç kaynağı (#### W) çıkarılmıştır ve sistemde eksik. eksiktir. Güç kaynağını kontrol edin. Bkz. “Sorun Giderme - Güç Kaynakları” sayfa 165. E1614 Güç Kaynağı # Belirtilen güç kaynağı (#### W) arızalıdır. hatası. Güç kaynağını kontrol edin. Bkz. “Sorun Giderme - Güç Kaynakları” sayfa 165. E1618 Güç Kaynağı #'de (#### W) öngörülebilir arıza. PSU'yu kontrol edin. Bir güç kaynağı pervanesi Bkz.
Tablo 1-1. LCD Durum İletileri (devamı) Nedenler Düzeltici İşlemler E1629 Güç gerekiyor > PSU watt değeri. PSU ve yapılandırmay ı kontrol edin. Sistem yapılandırması, kısıtlandığında bile güç kaynaklarının sağlayabildiğinden daha fazla güç gerektiriyordur. Sisteme verilen gücü kapatın, sisteme yeterli güç verilip verilmediğini kontrol edin. Sistem güç gereksinimleri hakkında bilgi için bkz. Başlarken Kılavuzu. E1631 Sistemin güç çekişi eşiği aştı. Destek birimine başvurun.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin E1711 Veriyolu ## Aygıt ## İşlev ##'de PCI eşlik hatası. Nedenler Düzeltici İşlemler Sistem BIOS'u PCI yapılandırma alanında veriyolu ##, aygıt ##, işlev ##'de bir PCI eşlik hatası bildirmiştir. PCIe genişletme kartlarını çıkarın ve yeniden yerleştirin. Sorun devam ederse, bkz. “Sorun Giderme - Genişletme Kartları” sayfa 175. Yuva #'da PCI Sistem BIOS'u belirtilen eşlik hatası.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin Düzeltici İşlemler Nedenler E1715 Önemli G/Ç Sistem BIOS'u sistemde Hatası. önemli bir hata olduğunu SEL'yi gözden belirlemiştir. geçirip temizleyin. Daha fazla bilgi için SEL'yi kontrol edin ve ardından temizleyin. Sisteme verilen AC gücü 10 saniyeliğine kesip sistemi yeniden başlatın. Sorun devam ederse, bkz. “Yardım Alma” sayfa 195. E1716 Yonga Kümesi IERR Veriyolu ## Aygıt ## İşlev ##. SEL'yi gözden geçirip temizleyin.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin E171F Veriyolu ## Aygıt ## İşlev ##'de PCIe önemli hatası. Yuva #'da PCIe önemli hatası. SEL'yi gözden geçirip temizleyin. Nedenler Düzeltici İşlemler Sistem BIOS'u PCI yapılandırma alanında veriyolu ##, aygıt ##, işlev ##'de bir PCIe önemli hatası bildirmiştir. PCIe genişletme kartlarını çıkarın ve yeniden yerleştirin. Sorun devam ederse, bkz. “Sorun Giderme - Genişletme Kartları” sayfa 175.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin E1A12 PCI Yükselticisi algılanmadı. Yükselticiyi kontrol edin. Nedenler Düzeltici İşlemler PCIe yükselticilerinin biri veya ikisi de eksiktir. Bu sistemin açılmasını engelliyordur. Eksik yükseltici kartlarını yeniden takın. Bkz. “Genişletme Kartı Yükselticisi 1'i Takma” sayfa 122 ve “Genişletme Kartı Yükselticisi 2'yi Takma” sayfa 124. E1813 Dahili Çift Dahili çift SD modülü kartı SD Modülü arızalanmıştır. Kartı # arızalandı. SD kartı kontrol edin.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin Nedenler E1A1D Kontrol Kontrol paneline giden USB paneli USB kablosu eksik veya arızalıdır. kablosu algılanmadı. Kabloyu kontrol edin. Düzeltici İşlemler Kabloyu yeniden takın. Sorun devam ederse kabloyu değiştirin. Sorun devam ederse, bkz. “Yardım Alma” sayfa 195. E2010 Bellek algılanmadı. DIMM'leri inceleyin. Sistemde belleği algılanmamıştır. Belleği takın veya bellek modüllerini yeniden yerleştirin. Bkz.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin Düzeltici İşlemler Nedenler E2015 DMA DMA denetleyicisi arızası Denetleyicisi Arızası AC güç dönüşümü yapın. Sisteme verilen AC gücü 10 saniyeliğine kesip sistemi yeniden başlatın. E2016 Kesinti Kesinti denetleyicisi Denetleyicisi arızalıdır. arızası. AC güç dönüşümü yapın. Sisteme verilen AC gücü 10 saniyeliğine kesip sistemi yeniden başlatın. E2017 Süreölçer yenileme arızası. AC güç dönüşümü yapın. Sorun devam ederse, bkz.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin Nedenler E201B Klavye Klavye denetleyici arızası. denetleyicisi hatası. AC güç dönüşümü yapın. E201C SMI başlatma hatası. AC güç dönüşümü yapın. Sistem yönetimi kesintisi (SMI) başlatma hatası. E201D Kapatma sınama hatası. AC güç dönüşümü yapın. BIOS kapatma sınaması hatası. Düzeltici İşlemler Sisteme verilen AC gücü 10 saniyeliğine kesip sistemi yeniden başlatın. Sorun devam ederse, bkz. “Yardım Alma” sayfa 195.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin Düzeltici İşlemler Nedenler E2022 POST Görüntüden sonra genel hata. Özel hata iletileri için sırasında ekranı kontrol edin. genel hata. Ekrandaki iletiyi kontrol edin. E2026 Bellek başlatma hatası. Destek birimine başvurun. Geçersiz bellek yapılandırması. Bellek modüllerinin geçerli bir yapılandırmaya takıldığından emin olun. Bkz. “Genel Bellek Modülü Montaj Yönergeleri” sayfa 99. Bkz. “Yardım Alma” sayfa 195. E2110 DIMM ##'de Çoklu Bit Hatası.
Tablo 1-1. LCD Durum İletileri (devamı) Kod Metin Nedenler I1910 izinsiz giriş Sistem kapağı çıkarılmıştır. algılandı. Kasa kapağını kontrol edin. Düzeltici İşlemler Kasa kapağını geri takın ve kasa kapağının düzgün takıldığından emin olun. Bkz. “Sistemi Kapatma” sayfa 83. I1911 LCD Günlüğü Dolu. Tüm Hataları incelemek için SEL'yi kontrol edin. LCD taşma iletisi. LCD'de sırayla en fazla on hata iletisi görüntülenebilir.
Tablo 1-1. Kod LCD Durum İletileri (devamı) Metin Düzeltici İşlemler Nedenler W1228 RAID Önceden RAID pilinin 24 Denetleyicisi saatten daha az şarjı kaldığı pili uyarısını verir. kapasitesi < 24 saat. RAID pilinin 24 saat sürekli şarj süresinden daha fazla şarj olmasını bekleyin. W1630 Güç kaynağı Güç kaynağı alt sistemi artık yedekliliği tamamen yedekli değildir. bozuldu. PSU kablolarını kontrol edin. Güç kaynaklarını yeniden takın. Bkz. “Sorun Giderme - Güç Kaynakları” sayfa 165.
Sistem İletileri Sistem iletileri sistemdeki olası bir sorun hakkında sizi bilgilendirmek için ekranda görünür. NOT: Tabloda belirtilmeyen bir sistem iletisi alırsanız, iletinin açıklaması ve önerilen işlem için ileti göründüğünde çalışmakta olan uygulamanın veya işletim sisteminin belgelerini inceleyin. Tablo 1-2. Sistem İletileri İleti Nedenler Dikkat! İDRAC6 yanıt vermiyor. Yeniden başlatılıyor. iDRAC6, BIOS iletişimine Sistemin yeniden düzgün çalışmadığından veya başlatılmasını bekleyin.
İleti Nedenler Düzeltici İşlemler Dikkat! Araya düğüm ekleme devre dışı! Bellek yapılandırması Araya Düğüm Eklemeyi desteklemiyor. Bellek yapılandırması değiştirilmiştir (örneğin, bir bellek modülü arızalanmıştır), bu nedenle araya düğüm ekleme desteklenememektedir. Sistem araya düğüm ekleme özelliği olmadan çalışacaktır. Bellek modüllerinin araya düğüm eklemeyi destekleyen bir yapılandırmaya takıldığından emin olun. Olası nedenler hakkında ek bilgi için diğer sistem iletilerini inceleyin.
İleti Nedenler Düzeltici İşlemler Dikkat! Önceki önyükleme sırasında önemli sistem hatası. Bir hata sistemin yeniden başlatılmasına neden olmuştur. Olası nedenler hakkında ek bilgi için diğer sistem iletilerini inceleyin. BIOS Sistem üretim modundadır. MANUFACTURING MODE (BIOS ÜRETİM MODU) algılandı. MANUFACTURING MODE (ÜRETİM MODU) sonraki önyüklemeden sonra temizlenecek. Normal çalışma sistemin yeniden başlatılması gerekiyor. Sistemi üretim modundan çıkarmak için yeniden başlatın.
İleti Nedenler Düzeltici İşlemler Farklı önbellek boyutlarına sahip CPU'lar algılandı. Sisteme birbiriyle uyumsuz işlemciler takılmıştır. Tüm işlemcilerin aynı önbellek boyutlarına, çekirdek sayısına ve güç değerine sahip olduğundan emin olun. İşlemcilerin düzgün takıldığından emin olun. Bkz. “İşlemciler” sayfa 134. Sistem, UEFI önyükleme modu BIOS'ta etkin olduğundan ve önyükleme işletim sistemi UEFI olmadığından önyükleme yapamamıştır.
İleti Nedenler Düzeltici İşlemler Tümleşik NICx ve NICy: İS NIC' i=, Yönetim Paylaşımlı NIC= İşletim sistemi NIC arabirimi BIOS'ta ayarlanmıştır. Yönetim Paylaşımlı NIC arabirimi yönetim araçlarında ayarlanmıştır. NIC ayarları için system management software'i veya Sistem Kurulumu programını kontrol edin. Sorun görülürse, bkz. “Sorun Giderme NIC'ler” sayfa 162. Hata 8602 Yardımcı Aygıt Arızası.
İleti Nedenler Düzeltici İşlemler Klavye denetleyici arızası. Arızalı klavye denetleyicisi; arızalı sistem kartı. Bkz. “Yardım Alma” sayfa 195. Klavye veri çizgisi hatası. Klavye tuş takılma hatası. Klavye kablo konektörünü Klavye kablosunu yeniden yanlış takılmıştır veya klavye takın. Sorun devam ederse, arızalıdır. bkz. “Sorun Giderme - USB Aygıtları” sayfa 160. Klavye sigortası yandı. Klavye konektöründe aşırı akım algılanmıştır.
İleti Nedenler Düzeltici İşlemler Hiçbir önyükleme aygıtı yok. Arızalı veya eksik optik sürücü alt sistemi, sabit sürücü veya sabit sürücü alt sistemi ya da önyükleme yapılamayan USB anahtarı takılmıştır. Önyükleme yapılabilir bir USB anahtarı, CD veya sabit sürücü kullanın. Sorun devam ederse, bkz. “Sorun Giderme - Dahili USB Anahtarı” sayfa 169, “Sorun Giderme - USB Aygıtları” sayfa 160, “Sorun Giderme - Optik Sürücü” sayfa 172, ve “Sorun Giderme - Sabit Sürücü” sayfa 173.
İleti Nedenler Düzeltici İşlemler PCIe Eğitim Hatası: Beklenen Bağlantı Genişliği x, Gerçek Bağlantı Genişliği y. PCIe kartı arızalıdır veya belirtilen yuvaya yanlış takılmıştır. PCIe kartını belirtilen yuva numarasına yeniden takın. Bkz. “Sorun Giderme Genişletme Kartları” sayfa 175. Sorun devam ederse, bkz. “Yardım Alma” sayfa 195. Tak ve Çalıştır Yapılandırma Hatası. PCle aygıtı başlatılırken NVRAM_CLR anahtarını boş hatayla karşılaşılmıştır; sistem konuma takın (1 ve 3. pinler) kartı arızalıdır.
İleti Nedenler Düzeltici İşlemler SATA bağlantı SATA bağlantı noktasına bağlı Arızalı sürücüyü değiştirin. noktası x aygıtı olan sürücü arızalıdır. otomatik algılama hatası. SATA bağlantı noktası x aygıtı yapılandırma hatası. SATA bağlantı noktası 0 aygıtı arızası. İstenen sektör bulunamadı. Arızalı sabit sürücü, USB aygıtı veya USB ortamı. USB ortamını veya aygıtını değiştirin. USB veya SAS arka panel kablolarının düzgün şekilde bağlandığından emin olun. Sisteminize takılan uygun sürücüler için bkz.
İleti Düzeltici İşlemler Nedenler Gün saati Saat ve Tarih ayarları ayarlanmamış, yanlıştır; sistem pili arızalıdır. lütfen KURULUM?programı nı çalıştırın. Saat ve Tarih ayarlarını kontrol edin. Bkz. “Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma” sayfa 59. Sorun devam ederse sistem pilini değiştirin. Bkz. “Sistem Pili” sayfa 140. Saat yongası sayacı 2 hata verdi. Arızalı sistem kartı. Bkz. “Yardım Alma” sayfa 195. TPM veya TCM yapılandırma işlemi kabul edildi.
İleti Nedenler Düzeltici İşlemler Sistem Hizmetleri görüntüsü başlatılamıyor. Sistem durduruldu! Sistem Hizmetleri görüntüsü sistem ürün bilgisinde bozulduğundan veya sistem kartı değişikliği nedeniyle kaybolduğundan sistem tuşuna basıldıktan sonra durdurulmuştur. Sistemi yeniden başlatın ve Yaşam Döngüsü Denetleyicisini tam işlevselliği eski durumuna getirmek için en son yazılımla güncelleyin. Daha fazla bilgi için Yaşam Döngüsü Denetleyicisi kullanıcı belgelerine bakın.
İleti Nedenler Düzeltici İşlemler Desteklenmeyen bellek yapılandırması. Yuvalar arasında DIMM uyuşmazlığı algılandı: x,x,... Geçersiz bellek yapılandırması. Belirtilen yuvalardaki bellek modülleri uyumsuzdur. Bellek modüllerinin geçerli bir yapılandırmaya takıldığından emin olun. Bkz. “Genel Bellek Modülü Montaj Yönergeleri” sayfa 99. Uyarı: Bir önemli hata sistemin sıfırlanmasına neden oldu! Lütfen sistemin olay günlüğünü kontrol edin.
İleti Nedenler Düzeltici İşlemler Uyarı! Gerekli güç PSU watt değerini aşıyor. PSU'yu ve sistem yapılandırmasını kontrol edin. Sistemin işlemci yapılandırmaları, bellek modülleri ve genişletme kartları güç kaynakları tarafından desteklenmiyor olabilir. Sistem bileşenleri son zamanlarda yükseltildiyse, sistemi önceki yapılandırmaya geri döndürün. Sistem bu uyarı olmaksızın önyükleme yapıyorsa değiştirilen bileşenler bu güç kaynağı tarafından desteklenmiyor demektir.
İleti Nedenler Düzeltici İşlemler HyperTransport hatası sistemin sıfırlanmasına neden oldu! Lütfen ayrıntılar için sistemin olay günlüğünü kontrol edin! Bir önemli hata meydana gelmiş ve sistemin yeniden başlatılmasına neden olmuştur. Hata sırasında kaydedilen bilgiler için SEL'yi kontrol edin. SEL'de belirtilen her türlü arızalı bileşen için “Sisteminizle İlgili Sorun Giderme” sayfa 159'deki sorun giderme kısmına bakın.
İleti Nedenler Düzeltici İşlemler Uyarı: Takılı bellek yapılandırması optimal değil. Geçerli bellek yapılandırmaları hakkında daha fazla bilgi için, lütfen teknik destek web sitesinde bulunan sistem belgelerine bakın. Geçersiz bellek yapılandırması. Sistem azaltılmış işlevlerle çalışacaktır. Bellek modüllerinin geçerli bir yapılandırmaya takıldığından emin olun. Bkz. “Genel Bellek Modülü Montaj Yönergeleri” sayfa 99. Sorun devam ederse, bkz. “Sorun Giderme - Sistem Belleği” sayfa 167.
Tanı İletileri Sistemin tanı yardımcı programları sisteminizde tanı sınamaları çalıştırırsanız ileti gönderebilir. Sistem tanı araçları hakkında daha fazla bilgi için, bkz. “Sistem Tanılama Araçlarını Çalıştırma” sayfa 179. Uyarı İletileri Systems management software sisteminiz için uyarı iletileri oluşturur. Uyarı iletileri sürücü, sıcaklık, pervane ve güç koşulları için bilgi, durum, uyarı ve arıza iletilerini içerir. Daha fazla bilgi için support.dell.
Sisteminiz Hakkında
Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma Sistem Kurulumu Programı, sistem donanımınızı yönetmenizi ve BIOS düzeyi seçenekleri belirtmenizi sağlar.
NOT: UEFI önyükleme modunda kurulabilmeleri için işletim sistemlerinin UEFI uyumlu (örneğin, Microsoft® Windows Server® 2008 x64 sürümü) olması gerekir. DOS ve 32 bit işletim sistemleri UEFI'yı desteklemez ve yalnızca BIOS önyükleme modu ile kurulabilir. Sistem Kurulumu Programına Girme 1 Sisteminizi açın veya yeniden başlatın.
Sistem Kurulumu Seçenekleri Ana Ekran NOT: Sistem Kurulumu programına ait seçenekler sistem yapılandırmasına bağlı olarak değişir. NOT: Sistem Kurulumu programı varsayılanları mümkün olduğu yerlerde aşağıdaki kısımlarda ilgili seçeneklerin altında belirtilmiştir.
Seçenek Açıklama Sistem Saati Sistemin dahili saatini ayarlar. Sistem Tarihi Sistemin dahili takvimindeki tarihi ayarlar. Bellek Ayarları Takılan bellekle ilgili bilgileri gösterir. Bkz. “Bellek Ayarları Ekranı” sayfa 63. İşlemci Ayarları İşlemcilerle ilgili bilgileri (hız, önbellek, boyut vs.) gösterir. Bkz. “İşlemci Ayarları Ekranı” sayfa 64. SATA Ayarları Tümleşik SATA denetleyicisini ve bağlantı noktalarını etkinleştirmek veya devre dışı bırakmak için kullanılan bir ekranı görüntüler. Bkz.
Seçenek Açıklama Klavye NumLock'u (Açık varsayılan) 101 veya 102 tuşlu klavyelerde (84 tuşlu klavyeler için geçerli değildir) sisteminizin NumLock modu etkin olarak başlatılıp başlatılmayacağını belirler. Klavye Hatalarını Bildir (Bildir varsayılan) POST sırasında klavye hatalarının bildirilmesini etkinleştirir ya da devre dışı bırakır. Klavye takılı ana makine sistemleri için Bildir'i seçin.
İşlemci Ayarları Ekranı Seçenek Açıklama 64 bit İşlemcilerin 64 bit uzantıları destekleyip desteklemediğini belirtir. Çekirdek Hızı İşlemcinin saat hızını gösterir. Veriyolu Hızı İşlemcinin veriyolu hızını gösterir. Hyper Transport Teknolojisi HyperTransport bağlantı hızını gösterir ve sisteme bağlı (HT3 varsayılan) olarak, bu alan salt okunur olabilir. HT3 destekli sistemler varsayılan olarak HT3 ile birlikte gönderilir.
SATA Ayarları Ekranı Seçenek Açıklama Tümleşik SATA (Kapalı varsayılan) ATA Modu tümleşik SATA denetleyicisini etkinleştirir. Kapalı denetleyiciyi devre dışı bırakır. Bağlantı Noktası A (Kapalı varsayılan) Otomatik SATA bağlantı noktasına bağlı aygıt için BIOS desteğini etkinleştirir. Kapalı aygıt için BIOS desteğini devre dışı bırakır.
Tümleşik Aygıtlar Ekranı Seçenek Açıklama Tümleşik SAS Denetleyicisi (Etkin varsayılan) Tümleşik SAS denetleyicisini etkinleştirir veya devre dışı bırakır. Kullanıcı Tarafından Erişilebilir USB Bağlantı Noktaları (Tüm Bağlantı Noktaları Açık varsayılan) Kullanıcının erişebileceği USB bağlantı noktalarını etkinleştirir ya da devre dışı bırakır. Seçenekler Tüm Bağlantı Noktaları Açık, Yalnızca Arka Bağlantı Noktaları Açık ve Tüm Bağlantı Noktaları Kapalı'dır.
PCI IRQ Atamaları Ekranı Seçenek Açıklama Belirli bir aygıt için bir IRQ'yu elle seçmek için <+> ve <-> tuşlarını kullanın veya BIOS'un sistem başlangıcında bir IRQ değeri seçmesini sağlamak için Varsayılan'ı seçin. Seri İletişim Ekranı Seçenek Açıklama Seri İletişim (Konsol Yeniden Yönlendirme Olmadan Açık varsayılan) Seri iletişim aygıtlarının (Seri Aygıt 1 ve Seri Aygıt 2) BIOS'ta etkinleştirilip etkinleştirilmeyeceğini seçer.
Seçenek Açıklama Uzak Uçbirim Türü Uzak konsol uçbirim türünü VT100/VT220 veya ANSI (VT 100/VT220 varsayılan) olarak ayarlar. İşletim sistemi arabirimi yüklendiğinde BIOS konsol yeniden yönlendirmesini etkinleştirir ya da devre dışı bırakır. Önyüklemeden Sonra Yeniden Yönlendirme (Etkin varsayılan) Güç Yönetimi Ekranı Seçenek Açıklama Seçenekler İS Denetimi, Etkin Güç Denetleyicisi, Özel veya Maksimum Performans'dır.
Sistem Güvenlik Ekranı Seçenek Açıklama Sistem Şifresi Şifre güvenliği özeliğinin mevcut durumunu gösterir ve yeni bir sistem şifresinin atanmasına ve doğrulanmasına olanak tanır. NOT: Daha fazla bilgi için “Sistem Şifresini Kullanma” sayfa 73 Kullanımı. Kurulum Şifresi Bir kurulumu şifresi kullanarak Sistem Kurulumu programına erişimi kısıtlar. NOT: Daha fazla bilgi için bkz. “Sistem Şifresini Kullanma” sayfa 73.
Seçenek Açıklama AC Gücü Eski Durumuna Getirme Gecikme Elektrik yeniden geldikten sonra sistemin ne zaman yeniden başlatılacağını belirler. Seçenekler Hemen, Rastgele (30 - 240 saniye arasında rastgele bir değer) veya kullanıcının tanımladığı 30 - 240 saniye arasındaki bir değerdir. Kullanıcının Tanımladığı Gecikme Kullanıcı tarafından tanımlanan gecikme.
NOT: USB klavye etkinleşene kadar sistem yanıt vermez. İşletim sisteminiz tuşuna basmadan önce yüklemeye başlarsa, sistemin önyüklemeyi bitirmesini bekleyin, ardından sisteminizi yeniden başlatın ve yeniden deneyin. UEFI Önyükleme Yöneticisi Gezinme Tuşlarını Kullanma Anahtarlar İşlem Yukarı ok Önceki alana gider ve alanı vurgular. Aşağı ok Sonraki alana gider ve alanı vurgular. Boşluk tuşu, , <+>, <–> Bir alandaki ayarlar arasında döner.
Seçenek Açıklama UEFI Önyükleme Ayarları Önyükleme seçeneklerini eklemenizi, silmenizi, etkinleştirmenizi veya devre dışı bırakmanızı; önyükleme sırasını değiştirmenizi; veya bir kerelik önyükleme seçeneğini uygulamanızı sağlar. Sistem Yardımcı Programları Sistem Kurulumu programına, Sistem Hizmetlerine (Birleştirilmiş Sunucu Yapılandırıcısı [USC]) ve BIOS düzeyi önyükleme seçeneklerine erişmenizi sağlar.
Sistem ve Kurulum Şifresi Özellikleri NOT: Şifrenizi unuttuysanız, bkz. “Unutulan Bir Şifreyi Silme” sayfa 194. Sisteminiz sistem şifresi özelliği etkinleştirilmeden gönderilir. Sistemi yalnızca sistem şifresi koruması varken çalıştırın. DİKKAT: Şifre özellikleri, sisteminizdeki veriler için temel düzeyde güvenlik sağlar. DİKKAT: Sistem çalışıyorsa ve başıboş bırakılmışsa, isteyen herkes sisteminizde depolanan verilere erişebilir.
NOT: Sistem şifresini belirlemeden alandan çıkmak için, başka bir alana geçmek üzere tuşuna veya adım 5'i tamamlamadan önce tuşuna basın. 4 tuşuna basın. 5 Şifrenizi onaylamak için, ikinci kez yazın ve tuşuna basın. Sistem Şifresi Etkin olarak değişir. Sistem Kurulumu programından çıkın ve sisteminizi kullanmaya başlayın. 6 Bu noktada şifre korumasının geçerli olması için sistemi yeniden başlatın veya çalışmaya devam edin.
NOT: Bilgisayarınızı izinsiz değişikliklerden korumak için Şifre Durumu özelliğini Sistem Şifresi ve Kurulum Şifresi ile birlikte kullanabilirsiniz. Mevcut Bir Sistem Parolasını Silme ya da Değiştirme 1 Sistem Kurulumu programına girin ve Sistem Güvenliği seçeneğini seçin. 2 Kurulum Şifresi'ni vurgulayın, kurulum şifresi penceresine erişmek için tuşuna basın. Mevcut kurulum şifresini silmek için tuşuna iki kez basın. Ayar, Etkin Değil olarak değişir.
Etkin Bir Kurulum Şifresi İle Çalışma Kurulum Şifresi Etkin ise, Sistem Kurulumu seçeneklerinin çoğunu değiştirmeden önce doğru kurulum şifresini girmeniz gerekir. Üç kerede doğru parolayı yazmazsanız, sistem Sistem Kurulumu ekranlarını görüntülemenize izin verir ancak değişiklik yapmanıza izin vermez. Aşağıdaki seçenekler istisnadır: Sistem Şifresi Etkin değilse ve Şifre Durumu seçeneği ile kilitlenmediyse, bir sistem şifresi belirleyebilirsiniz. Mevcut sistem şifresini silemez veya değiştiremezsiniz.
iDRAC6 Yapılandırma Yardımcı Programı iDRAC6 Yapılandırma Yardımcı Programı iDRAC6 ve yönetilen sunucuya ait parametreleri görüntülemenizi ve ayarlamanızı sağlayan bir önyükleme yapılandırma ortamıdır.
Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma
Sistem Bileşenlerinin Montajı Önerilen Araçlar Bu kısımdaki yordamları gerçekleştirmek için aşağıdaki öğelere ihtiyaç duyabilirsiniz: • Sistem kilidinin anahtarı • 1 ve 2 numaralı Phillips tornavidalar • T8 ve T10 Torx anahtarları • Topraklama bilekliği Sistemin İçinde UYARI: Sistem kaldırmaya ihtiyaç duyarsanız, daima başkalarından yardım alın. Yaralanmayı önlemek için, sistemi kendi başınıza kaldırmaya çalışmayın. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
Şekil 3-1.
Ön Çerçeve (İsteğe Bağlı) Ön Çerçeveyi Sökme 1 Ön çerçevenin sol kenarındaki kilidi açın. 2 Kilidin yanındaki serbest bırakma mandalını yukarıya doğru kaldırın. 3 Çerçevenin sol kenarını ön panelden dışarıya doğru döndürün. 4 Çerçevenin sağ kenarını kancadan kurtarın ve çerçeveyi sistemden dışarıya doğru çekin. Bkz. şekil 3-2. Şekil 3-2. Ön Çerçeveyi Sökme ve Takma 1 2 3 1 Serbest bırakma mandalı 3 Ön çerçeve 2 Kilit Ön Çerçeveyi Takma 1 Çerçevenin sağ kenarını kasaya kancalayın.
Sistemi Açma ve Kapatma UYARI: Sistem kaldırmaya ihtiyaç duyarsanız, daima başkalarından yardım alın. Yaralanmayı önlemek için, sistemi kendi başınıza kaldırmaya çalışmayın. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
Şekil 3-3. Sistemi Açma ve Kapatma 1 2 3 1 Mandal 3 Kapak 2 Mandal açma kilidi Sistemi Kapatma 1 Kapağı kasaya yerleştirin ve sistemin arkasına doğru hafifçe dengeleyin, bu şekilde kapağın yanlarındaki yuvalar kasanın yanlarındaki karşılık gelen kancalara takılır. Bkz. şekil 3-3. NOT: Sistemi düzgün biçimde kapatmak için, soğutma örtüsündeki tırnakların kasadaki yuvalara oturduğundan emin olun. Bkz. şekil 3-9. 2 Kapağı yerine oturuncaya kadar kasanın önüne doğru kaydırın.
Sabit Sürücüler Tüm sürücüler sisteme ön kasa tertibatına monteli SAS/SATA arka panel devre kartı üzerinden bağlanır. Sabit sürücüler sabit sürücü bölmelerine takılan çalışırken takılabilir sürücü taşıyıcıları içerisinde sunulur. DİKKAT: Sistem çalışırken bir sürücüyü sökmeye ve takmaya çalışmadan önce ana makine adaptörünün sürücüyü çalışırken takma ve sökmeyi desteklediğinden emin olmak için SAS denetleyici kartının belgelerine bakın.
Şekil 3-4. Boş Bir Sabit Sürücüyü Sökme ve Takma 1 2 1 2 Boş sabit sürücü Serbest bırakma düğmesi Boş Bir Sabit Sürücüyü Takma 1 Takılıysa, ön çerçeveyi sökün. Bkz. “Ön Çerçeveyi Sökme” sayfa 81. 2 Boş sabit sürücüyü serbest bırakma düğmesi tık sesi çıkarana kadar sürücü bölmesinin içine doğru itin. 3 Mümkünse, ön çerçeveyi yeniden yerleştirin. Bkz.“Ön Çerçeveyi Takma” sayfa 81.
Bir Sabit Sürücü Taşıyıcısını Sökme DİKKAT: İşletim sisteminizin sürücülerin çalışırken takılmasını desteklediğinden emin olun. İşletim sisteminizle birlikte verilen belgelere bakın. 1 Takılıysa, ön çerçeveyi sökün. Bkz.“Ön Çerçeveyi Sökme” sayfa 81. 2 Yönetim yazılımını kullanarak sürücüyü sökmeye hazırlayın. Sürücü taşıyıcısının üzerindeki sabit sürücü göstergeleri sürücünün güvenli bir şekilde çıkarılabileceğini gösterene kadar bekleyin.
Şekil 3-5. Sabit Sürücü Taşıyıcısını Sökme ve Takma 1 2 3 1 Serbest bırakma düğmesi 3 Sabit sürücü taşıyıcısı kolu 2 Sabit sürücü taşıyıcısı Bir Sabit Sürücü Taşıyıcısını Takma DİKKAT: Yalnızca SAS/SATA arka paneli ile kullanım için test edilmiş ve onaylanmış sürücüleri kullanın. DİKKAT: Bir sabit sürücüyü takarken, yan yana duran sürücülerin tamamen takılı olduğundan emin olun.
Sabit Sürücüyü Sabit Sürücü Taşıyıcısından Çıkarma Sabit sürücü taşıyıcısının kaydırma raylarındaki dört vidayı sökün ve sabit sürücüyü taşıyıcıdan ayırın. Bkz. şekil 3-6. Şekil 3-6. Çalışırken Takılabilir Bir Sabit Sürücüyü Sabit Sürücü Taşıyıcısına Takma ve Buradan Sökme 1 4 2 3 1 Sabit sürücü 2 Sabit sürücü taşıyıcısı 3 SAS/SATA vida deliği 4 Vidalar (4) Sabit Sürücüyü Sabit Sürücü Taşıyıcısına Takma 1 Sabit sürücüyü arkadaki sürücünün konnektör ucuyla birlikte sabit sürücü taşıyıcısına takın.
Optik Sürücü Sisteminiz isteğe bağlı bir ince SATA DVD-ROM veya DVD+/-RW optik sürücüyle birlikte sunulur. NOT: DVD aygıtları yalnızca veri içindir. Optik Sürücüyü Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
Şekil 3-7. Optik Sürücüyü Sökme ve Takma 1 2 3 1 Güç/veri kablosu 3 Optik sürücü 2 Serbest bırakma tırnağı Optik Sürücü Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
5 Güç/veri kablosunu sürücünün arkasına ve sistem kartına bağlayın. Kabloyu, sıkışmasını ve bükülmesini önlemek için sistemin içinden düzgünce geçirin. Daha fazla bilgi için, bkz. “Ön Kasa Aksamı” sayfa 96. 6 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 7 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın. 8 Mümkünse, ön çerçeveyi yeniden yerleştirin. Bkz. “Ön Çerçeveyi Takma” sayfa 81.
Güç Kaynağını Çıkarma DİKKAT: Sistem normal çalışma için bir adet güç kaynağına ihtiyaç duyar. Güç yedekli sistemlerde, sistem açıkken her seferinde bir adet güç kaynağını çıkarın ve değiştirin. 1 Güç kablosunu güç kaynağından çıkarın. 2 Güç kablosunu güç kaynağından çıkarın ve sistem kablolarını toplayan ve sabitleyen Velcro şeritlerini sökün. NOT: Güç kaynağını sökmenizi engelliyorsa isteğe bağlı kablo yönlendirme kolunu mandalını açıp kaldırmanız gerekebilir.
Güç Kaynağı Takma 1 Güç kaynaklarının aynı türde ve aynı çıkış gücüne sahip olduğundan emin olun. NOT: Maksimum çıkış gücü (watt olarak gösterilir) güç kaynağının etiketinin üzerinde gösterilir. 2 Mümkünse boş güç kaynağını çıkarın. Bkz. “Boş Güç Kaynağını Çıkarma” sayfa 93. 3 Güç kaynağı tamamen yerleşip serbest bırakma mandalı yerine oturuncaya kadar yeni güç kaynağını kasanın içine doğru kaydırın. Bkz. şekil 3-8. NOT: Önceki yordamın adım 1.
Soğutma Örtüsü Soğutma örtüsü bellek modüllerini örter ve sisteme hava akışı sağlar. Soğutma Örtüsünü Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir.
Şekil 3-9. Soğutma Örtüsünü Sökme ve Takma 1 2 3 4 1 Soğutma örtüsü 2 RAID pili taşıyıcısı 3 Örtü tırnakları (6) 4 Dokunma noktaları (2) Soğutma Örtüsünü Takma NOT: Soğutma örtüsünün sistemde düzgün hizalanması için, sistemin içindeki kabloların kasa duvarı boyunca geçirilmiş olduğundan emin olun. Bkz. şekil 3-10. 1 Soğutma örtüsünü sistemin içine doğru indirin ve örtünün tırnaklarını sistemdeki yuvalarla hizalayın. Bkz. şekil 3-9. 2 RAID pilini soğutma örtüsündeki pil taşıyıcısına takın. Bkz.
Ön Kasa Aksamı Ön kasa aksamı sabit sürücüler, SAS/SATA arka paneli, optik sürücü, kontrol paneli tertibatı ve ön panel ekranından oluşur. Ön kasa aksamı kasa duvarlarına bir kayan ray sistemi ile monte edilir. Ön kasa aksamını kasadan dışarıya doğru kaydırmak için: 1 Takılıysa, ön çerçeveyi sökün. Bkz.“Ön Çerçeveyi Sökme” sayfa 81. 2 Sistemi varsa bağlı çevre birimleriyle birlikte kapatın ve sistemin fişini çekin. 3 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. 4 Soğutma örtüsünü çıkarın. Bkz.
Şekil 3-10. Ön Kasa Aksamını Kaydırma 5 3 4 2 1 8 7 6 1 Ön kasa aksamı 2 Kontrol paneli kablosu 3 USB kablosu 4 SAS arka panel güç kablosu 5 Kablo tutucusu 6 Serbest bırakma tırnakları (2) 7 SATA kablosu 8 SAS kabloları (2) Ön kasa aksamını yeniden kilitli konuma kaydırmak için: 1 Aksamı yerine oturuncaya kadar içeriye doğru kaydırın. NOT: Sistemin düzgün soğutulması için, sistemin içindeki kabloların hava akışını engellemediğinden emin olun.
3 SAS arka panel/USB/optik sürücü güç kablolarını kablo kelepçesinin içinden geçirin. Kontrol paneli kablosunu kablo kelepçesinin içinden ve daha sonra kasa duvarı boyunca geçirin. Bkz. şekil 3-10. DİKKAT: Bellek modüllerinin hasar görmesini engellemek için, ön kasa aksamına bağlı olan tüm kabloların engellerden arındırılmış olduğundan emin olun. 4 Mümkünse, SAS kablolarını SAS arka paneline bağlayın. 5 Soğutma örtüsünü yeniden yerleştirin. Bkz. “Soğutma Örtüsünü Takma” sayfa 95. 6 Sistemi kapatın. Bkz.
• • Esneklik için bellek boyutları ile seviyelerin bir arada kullanımına izin verilmiştir. 256 GB'a kadar bellek (32 adet 8 GB RDIMM'le birlikte) Genel Bellek Modülü Montaj Yönergeleri Sisteminizden en uygun performansı elde etmek için, sistem belleğinizi yapılandırırken, aşağıdaki genel yönergelere uyun: NOT: Bu yönergelere uymayan bellek yapılandırmaları sisteminizin başlatılmasını ve video çıktısı üretmesini engelleyebilir.
NOT: Bellek yedekleme ve araya düğüm ekleme özellikleri aynı anda kullanılamaz. Bellek yedeklemeyi kullanmak için, Sistem Kurulumu programındaki Araya Düğüm Ekleme seçeneğini devre dışı bırakmalısınız. Bellek yedeklemeyi desteklemek için, her CPU'ya ait sekiz DIMM soketinin hepsi de yerleştirilmelidir.
Tablo 3-3.
Bellek Yapılandırmaları (Dört İşlemcili) (devamı) 160b 32 8 ve 2 192c 256 32 8 ve 4 32 8 Düzen DIMM Türü DIMM Boyutu (GB olarak) İşlemciler DIMM Sayısı Sistem Kapasitesi Tablo 3-3.
Bellek Modüllerini Takma UYARI: Sistem kapatıldıktan sonra bir süre bellek modülleri dokunulamayacak kadar sıcak kalır. Bellek modülleri ile herhangi bir işlem yapmadan önce soğumaları için bir süre bekleyin. Bellek modüllerini kart kenarlarından tutun. Bellek modülündeki bileşenlere ve konnektörlere dokunmaktan kaçının. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
Şekil 3-11. Bellek Modülü Takma ve Sökme 1 2 3 1 Bellek modülü 3 Hizalama dişi 2 Bellek modülü soket ejektörleri (2) 7 Bellek modülünün kenar konnektörünü bellek modülü soketindeki hizalama dişi ile aynı hizaya getirin ve bellek modülünü sokete yerleştirin. NOT: Bellek modülünde, bellek modülünü sokete sadece tek bir şekilde takabilmenizi sağlayan bir hizalama dişi bulunmaktadır. 8 Bellek modülünü sokete kilitlemek için bellek modülünün üzerine baş parmaklarınızla bastırın.
12 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 13 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın. 14 Mümkünse, ön çerçeveyi yeniden yerleştirin. Bkz. “Ön Çerçeveyi Takma” sayfa 81. 15 Sistemi açın, Sistem Kurulumu programına girmek için tuşuna basın ve ana Sistem Kurulumu ekranında Sistem Belleği ayarını kontrol edin. Sistemin değeri yeni takılan belleği gösterecek şekilde değiştirmiş olması gerekir.
3 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. DİKKAT: Bellek modülü bileşenlerine veya konnektörlere dokunmadığınızdan emin olarak, kartların herhangi birinin üzerindeki her bellek modülünü tutun. 4 Soğutma örtüsünü çıkarın. Bkz. “Soğutma Örtüsünü Çıkarma” sayfa 94. 5 Mümkünse, ön kasa aksamını kasadan dışarıya doğru kaydırın. Bkz. “Ön Kasa Aksamı” sayfa 96. 6 Bellek modülleri soketten çıkana kadar, soketin her iki kenarındaki ejektörlere bastırın. Bkz. şekil 3-11. 7 Bellek modülünü kaldırıp çıkarın.
Soğutma Fanları Sisteminiz bir pervane tertibatına monte edilmiş ve işlemciler, genişletme kartları ve bellek modülleri için soğutma sağlayan altı adet çalışırken takılabilir pervane içerir. NOT: Belirli bir pervanede sorun meydana gelirse, pervane numarası sistemin yönetim yazılımı tarafından gösterilir. Bu, soğutma pervanesi tertibatında bulunan pervane numaralarına dikkat ederek doğru pervaneyi kolayca belirleyip değiştirmenizi sağlar.
Şekil 3-12.
Soğutma Pervanesini Takma UYARI: Sistem açıkken sistemin kapağını açarsanız veya çıkarırsanız elektrik çarpması riskine maruz kalabilirsiniz. Soğutma pervanelerini sökerken veya takarken azami derece dikkatli olun. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
Şekil 3-13.
Soğutma Pervanesi Tertibatını Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Dahili USB Bellek Anahtarı Sisteminizin içine takılı isteğe bağlı bir USB bellek anahtarı önyükleme aygıtı, güvenlik anahtarı veya toplu depolama aygıtı olarak kullanılabilir. USB konnektörü Sistem Kurulumu programının Tümleşik Aygıtlar ekranındaki Dahili USB Bağlantı Noktası seçeneği ile etkinleştirilmelidir.
Şekil 3-14. USB Bellek Anahtarını Çıkarma ve Takma 1 2 1 USB bellek anahtarı konnektörü 2 USB bellek anahtarı Dahili NIC Donanım Anahtarı Sistemin tümleşik NIC'lerine ait gelecekte kullanılacak her türlü ek işlev sistem kartında bulunan iSCSI KEY soketindeki isteğe bağlı NIC donanım anahtarı takılarak etkinleştirilir. Bkz. şekil 6-1. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
Şekil 3-15. NIC Bellek Anahtarını Çıkarma ve Takma 1 2 1 NIC donanım anahtarı 2 ISCSI KEY konnektörü 5 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 6 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın.
Genişletme Kartları ve Genişletme Kartı Yükselticileri Genişletme Kartı Takma Yönergeleri Sisteminiz, sistem kartındaki konnektörleri ve iki adet genişletme kartı yükselticisini kullanarak altı adede kadar 2. Nesil PCle genişletme kartını destekler. Sistem kartında genişletme kartı yükselticilerini bulmak için, şekil 6-1'e bakın ve genisletme kartı yükselticilerinin üzerindeki genişletme kartı yükselticilerini bulmak için şekil 6-4 ve şekil 6-5'e bakın.
Tablo 3-4 düzgün soğutmadan ve mekanik uygunluktan emin olmak için genişletme kartlarının takılmasına ilişkin bir kılavuz sunmaktadır. En yüksek önceliğe sahip genişletme kartları belirtilen yuva önceliği kullanılarak önce takılmalıdır. Diğer genişletme kartları kart önceliği ve yuva önceliği sırasında göre takılmalıdır. Tablo 3-4. Genişletme Kartı Takma Önceliği Kart Öncelik Kart Türü Yuva Öncelik İzin Verilen Maks.
Genişletme Kartı Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-16. Genişletme Kartı Takma ve Çıkarma 1 2 3 1 Genişletme kartı mandalı 3 Genişletme kartı konnektörü 2 Genişletme kartı 9 Mümkünse, kabloları genişletme kartına takın. 10 Genişletme kartı mandalını eski konumuna getirin. 11 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 12 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın. 13 Kart için gereken aygıt sürücülerini kart belgelerinde açıklandığı şekilde yükleyin.
Genişletme Kartını Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Genişletme Kartı Yükselticisi 1'i Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-17.
Genişletme Kartı Yükselticisi 1'i Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
3 Takılıysa, genişletme kartını genişletme kartı yuvasından çıkarın. Bkz. “Genişletme Kartını Çıkarma” sayfa 119. 4 Genişletme kartı yükselticisini kaldırmak için, genişletme kartı yükselticisini sistem kartındaki konnektörden çıkarın. Bkz. şekil 3-18. Şekil 3-18.
Genişletme Kartı Yükselticisi 2'yi Takma 1 Genişletme kartı yükselticisini sistem kartının üzerindeki yükseltici kılavuzu pinleri ve kasanın üzerindeki yuva ile hizalayın. Bkz. şekil 3-17. 2 Genişletme kartı yükselticisini, genişletme kartı yükselticisi konnektörü tamamen oturana kadar yerine bastırın. 3 Mümkünse, genişletme kartlarını yeniden yerleştirin. Bkz. “Genişletme Kartı Takma” sayfa 117, sayfa 72. 4 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83.
6 İki hizalama kılavuzunu da bükün ve depolama denetleyicisi kartını konnektörden çıkarın. Bkz. şekil 3-19. 7 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. Şekil 3-19.
Tümleşik Depolama Denetleyicisi Kartını Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
RAID Pili (İsteğe Bağlı) Bu bölümdeki bilgiler yalnızca tümleşik bir pil yedekleme birimi bulunmayan isteğe bağlı PERC kartlarına sahip sistemler için geçerlidir. RAID Pilini Çıkarma 1 Sistemi varsa bağlı çevre birimleriyle birlikte kapatın ve sistemin fişini çekin. 2 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. 3 Soğutma pervanesi tertibatını sökün. Bkz. “Soğutma Pervanesi Tertibatını Sökme” sayfa 109.
Şekil 3-20. RAID Pilini Çıkarma ve Takma 1 2 3 4 5 1 RAID pili taşıyıcısı 2 RAID pili 3 RAID pili kablosu 4 RAID pili taşıyıcısı yuvası 5 Soğutma örtüsü RAID Pilini Takma 1 RAID pilini soğutma örtüsündeki pil taşıyıcısına takın. Bkz. şekil 3-20. 2 RAID pili kablosunu kasa duvarından ve pil taşıyıcısındaki yuvanın içinden geçirin. 3 Tüm kablo istiflerini pil taşıyıcısı yuvasının önündeki alanın içine sıkıştırın.
iDRAC6 Enterprise Kartı (İsteğe Bağlı) iDRAC6 Enterprise Kartını Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir.
Şekil 3-21. iDRAC6 Enterprise Kartını (İsteğe Bağlı) Takma ve Çıkarma 1 2 3 4 6 5 1 iDRAC6 enterprise kartı 2 VFlash ortam yuvası 3 VFlash SD kartı 4 Tutma boşluğu direkleri (2) 5 Tutma boşluğu tırnakları (2) 6 iDRAC6 enterprise kartı konnektörü iDRAC6 Enterprise Kartını Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
3 iDRAC6 Enterprise bağlantı noktasına ait plastik dolgu fişini sistemin arka panelinden çıkarın. Bkz. şekil 1-3. 4 Kartın ön kenarını sistem kartındaki iDRAC6 konnektörünün yanındaki iki plastik tutma boşluğu ile hizalayın ve kartı yerine doğru indirin. Bkz. şekil 3-21 ve şekil 6-1. Kartın önü tamamen oturduğunda, plastik boşluklar kartın kenarına geçer. 5 Mümkünse, Ethernet kablosunu sistemin arka panelindeki iDRAC6 Enterprise Kartı konnektörüne takın. Bkz. şekil 1-3. 6 Sistemi kapatın. Bkz.
Dahili Çift SD Modülü (İsteğe Bağlı) Dahili Çift SD Modülünü Çıkarma Yedeklilik seçeneği sistem kurulumu programının Tümleşik Aygıtlar ekranında Yansıma Moduna ayarlandığında, bilgiler bir SD karttan diğerine kopyalanır. Bkz. “Tümleşik Aygıtlar Ekranı” sayfa 66. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
Şekil 3-22. Dahili Çift SD Modülünü Çıkarma ve Takma 3 2 1 4 5 6 7 1 Kancalar (2) 2 SD kart yuvası 2 3 Dahili çift SD modülü 4 SD kart yuvası 1 5 Mandal 6 Kablo konnektörü 7 Güç kablosu Dahili Çift SD Modülünü Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
3 Modülü tepsinin alt tarafındaki tırnaklar ön kasa aksamının üzerindeki kancalara takılacak şekilde yerleştirin, ardından kartın diğer kenarını indirerek yerine takın. Bkz. şekil 3-1 ve şekil 3-22. 4 Dahili çift SD modülü kablosunu kontrol paneli devre kartındaki konnektöre bağlayın. 5 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 6 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın.
DİKKAT: İşlemciyi çıkarmayı düşünmüyorsanız, ısı alıcısını asla işlemciden ayırmayın. Uygun sıcaklık şartlarının sürdürülmesi için ısı alıcısı gereklidir. 7 2 Numaralı Phillips tornavida kullanarak, ısı emicinin tutma vidalarını gevşetin. Bkz. şekil 3-23. 8 Isı emiciyi yavaşça kaldırarak işlemciden çıkarın ve ısıl gres kaplı olarak kaldırın. Şekil 3-23.
DİKKAT: İşlemci soketinde güçlü basınç altında tutulur. Serbest bırakma kolunun sıkıca tutulmazsa aniden fırlayabileceğini unutmayın. 9 Baş parmağınızı işlemci soketi serbest bırakma kolunun üzerine sıkıca yerleştirin ve kolu itip tırnağın altından çekerek kilitli konumdan kurtarın. İşlemci soketten kurtulana kadar kolu yukarıya doğru 90 derece döndürün. Bkz. şekil 3-24. 10 İşlemci koruyucusunu yukarı doğru döndürün ve çıkarın. Bkz. şekil 3-24. Şekil 3-24.
Şekil 3-25. Boş İşlemciyi Çıkarma ve Takma 2 1 1 Serbest bırakma kolu 2 Boş işlemci DİKKAT: İşlemciyi çıkarırken, ZIF soketinin üzerindeki pinlerin kıvrılmamasına özen gösterin. pinlerin kıvrılması, sistem kartının kalıcı olarak zarar görmesine neden olabilir. 11 Dikkatlice işlemciyi soketten ayırın ve soketin yeni işlemci için hazır olması için serbest bırakma kolunu yukarıda bırakın. İşlemciyi çıkardıktan sonra, yeniden kullanım, iade veya geçici depolama için antistatik bir kaba yerleştirin.
İşlemci Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
10 Soket serbest bırakma kolunu yerine oturuncaya kadar döndürün. Bkz. şekil 3-24. NOT: Ek güç tüketen bir işlemci takıyorsanız kitiniz yedek bir ısı emicisi içerebilir. Yeni ısı emicisi asıl emiciden farklı değilmiş gibi görünebilir; ancak bu emici iyileştirilmiş ısıl dağılım özelliklerine sahiptir ve kullanılmalıdır. 11 Temiz tiftiksiz bir bez kullanarak, ısıl gresi ısı emicisinden temizleyin.
Sistem Pili Sistem Pilini Değiştirme UYARI: Yanlış takılan yeni pillerin patlama tehlikesi vardır. Pili yalnızca üretici tarafından önerilen tiple ya da dengi ile değiştirin. Ek bilgi için güvenlik bilgilerinize bakın. DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
3 Pil soketini bulun. Bkz. şekil 6-1. 4 Takılıysa, tümleşik depolama denetleyicisi kartını çıkarın. Bkz. “Tümleşik Depolama Denetleyicisi Kartını Çıkarma” sayfa 124. DİKKAT: Pil konnektörünün zarar görmemesi için, pili takarken ya da çıkarırken, konnektörü desteklemeniz gerekir. 5 Pili çıkarmak için konnektörün pozitif tarafından aşağıya doğru bastırarak pil konnektörünü destekleyin. 6 Pili kaldırarak konnektörün negatif tarafındaki sabitleme tırnaklarından çıkarın.
SAS Arka Paneli SAS Arka Panelini Sökme DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-27.
SAS Arka Panelini Takma 1 SAS arka panelindeki yuvaları ön kasa aksamındaki tırnaklarla hizalayın. 2 SAS arka panelini mavi serbest bırakma tırnakları yerlerine oturuncaya kadar aşağıya doğru kaydırın. 3 SAS veri kablolarını ve güç kablosunu arka panele takın. Bkz. şekil 3-27. 4 Sabit sürücüleri asıl yerlerine takın. Bkz. “Bir Sabit Sürücü Taşıyıcısını Takma” sayfa 87. 5 Gerekirse, güç/veri kablolarını kasa duvarı boyunca geçirin. Bkz. “Ön Kasa Aksamı” sayfa 96. 6 Soğutma örtüsünü yeniden yerleştirin. Bkz.
Güç Dağıtım Kartı Güç Dağıtım Kartını Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-28.
Güç Dağıtım Kartını Değiştirme DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Kontrol Paneli Tertibatı Kontrol Paneli Ekran Modülünü Sökme DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir.
Kontrol Paneli Ekran Modülünü Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Şekil 3-29.
Kontrol Paneli Tertibatını Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Kontrol Paneli Tertibatını Takma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Sistem Kartı Aksamı Sistem kartı aksamı bir yüksek hız konnektörü ile ara bağlantısı bulunan iki devre kartına bölünmüştür. • İşlemci kartı: Üzerinde bellek modülleri, güç kaynakları ve işlemciler için konnektörler bulunur. • G/Ç kartı: Üzerinde genişletme kartı yükselticileri ve genişletme kartları için konnektörler bulunur. Sistem Kartı Aksamını Çıkarma DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir.
8 Soğutma pervanesi tertibatını sökün. Bkz. “Soğutma Pervanesi Tertibatını Sökme” sayfa 109. UYARI: Sistem kapatıldıktan sonra ısı emicisi bir süre dokunulamayacak kadar sıcak kalır. G/Ç kartını veya işlemci kartını çıkarırken ısı emicilerine dokunmadığınızdan emin olun. 9 Isı emicilerini, boş işlemcileri ve işlemcileri çıkarın. Bkz. “İşlemciyi Çıkarma” sayfa 134. 10 G/Ç kartını çıkarıyorsanız, tüm genişletme kartlarını ve tümleşik depolama denetleyicisi kartını sökün. Bkz.
Şekil 3-30.
Sistem Kartı Aksamını Takma 1 Yeni sistem kartı aksamını paketinden çıkarın. G/Ç kartı çıkarılmadıysa adım 5'e gidin. 2 G/Ç kartını kenarıyla serbest bırakma pininden tutun ve kasanın içine doğru indirin. 3 G/Ç kartını tamamen düz biçimde oturana kadar kasanın altına yerleştirin. 4 Konnektörleri kasanın arka panelindeki bölmelere takarak G/Ç kartını sistemin arkasına doğru kaydırın. 5 İşlemci kartını koldan ve işlemci kartının kenarından (bkz. şekil 3-30) tutarak kasanın içine doğru indirin.
16 Kabloları sistem kartı aksamına, SAS arka paneline, kontrol paneli kartına ve optik sürücüye bağlayın. 17 Güç/veri kablolarını kasa duvarı boyunca geçirin. Bkz. “Ön Kasa Aksamı” sayfa 96. 18 Soğutma örtüsünü yeniden yerleştirin. Bkz. “Soğutma Örtüsünü Takma” sayfa 95. 19 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 20 Mümkünse, ön çerçeveyi yeniden yerleştirin. Bkz. “Ön Çerçeveyi Takma” sayfa 81. 21 Sistemin fişini prize takın ve takılı olan çevre birimleri de dahil olmak üzere sistemi açın.
Sistem Bileşenlerinin Montajı
Sisteminizle İlgili Sorun Giderme Sisteminiz ve Sizin İçin Önce Güvenlik DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir.
Sorun Giderme - Harici Bağlantılar Harici aygıtlarda sorun giderme işlemi yapmadan önce tüm harici kabloların harici konnektörlere düzgün şekilde takılı olduğundan emin olun. Sisteminizdeki ön ve arka panel konnektörleri için bkz. Şekil 1-1 ve Şekil 1-3. Sorun Giderme - Video Alt Sistemi 1 Sistemin ve monitörün güç bağlantılarını kontrol edin. 2 Sistemden monitöre giden video arabirimi kablolarını kontrol edin. 3 Sisteme iki monitör bağlandıysa, birini sökün.
3 Sistemi yeniden başlatın ve klavyeniz çalışıyorsa sistem kurulumu programına girin. Tüm USB bağlantı noktalarının etkin olduğundan emin olun. Bkz. “Tümleşik Aygıtlar Ekranı” sayfa 66. Klavyeniz çalışmıyorsa, uzaktan erişimi de kullanabilirsiniz. Sistem erişilebilir durumda değilse, sisteminizdeki NVRAM_CLR atlama telini ayarlama ve BIOS'u varsayılan ayarlara geri yükleme hakkındaki yönergeler için bkz. “Unutulan Bir Şifreyi Silme” sayfa 194.
Sorun Giderme - NIC'ler 1 Uygun çevrimiçi tanılama sınamasını çalıştırın. Bkz. “Çevrimiçi Tanılama Araçlarını Kullanma” sayfa 179. 2 Sistemi yeniden başlatın ve NIC denetleyicisine ait sistem iletisi olup olmadığını kontrol edin. 3 NIC konektöründeki ilgili göstergeyi denetleyin. Bkz. “NIC Gösterge Kodları” sayfa 23. • Bağlantı göstergesi yanmıyorsa, tüm kablo bağlantılarını kontrol edin. • Etkinlik göstergesi yanmıyorsa, ağ sürücüsü dosyaları hasarlı veya eksik olabilir.
Sorun Giderme - Sistemin Islanması DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
8 Uygun çevrimiçi tanılama sınamasını çalıştırın. Bkz. “Çevrimiçi Tanılama Araçlarını Kullanma” sayfa 179. Sınama başarısız olursa, bkz. “Yardım Alma” sayfa 195. Sorun Giderme - Sistemin Hasar Görmesi DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız.
Sorun Giderme - Sistem Pili NOT: Sistem uzun süre boyunca kapalı kalırsa (haftalarca veya aylarca) NVRAM sistem yapılandırması bilgilerini kaybedebilir. Bu durumun nedeni kusurlu bir pildir. 1 Saati ve tarihi Sistem Kurulumu programı üzerinden yeniden girin. Bkz. “Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma” sayfa 59. 2 Sistemi kapatın ve fişini en az bir saat için elektrik prizinden çekin. 3 Sistemin fişini yeniden prize takın ve sistemi açın. 4 Sistem Kurulumu programına girin.
Sorun Giderme - Sistem Soğutması Sorunları DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
2 LCD panel veya tanılama yazılımı tarafından gösterilen arızalı pervaneyi bulun. 3 Pervaneyi çıkarıp yeniden takın. Bkz. “Soğutma Pervanesini Sökme” sayfa 107 ve “Soğutma Pervanesini Takma” sayfa 109. NOT: Sistemin güç kaynağını tanıması ve düzgün çalışıp çalışmadığını belirlemesi için en az 30 saniye bekleyin. 4 Sorun çözülmezse, yeni bir pervane takın. Bkz. “Soğutma Pervanesini Sökme” sayfa 107 ve “Soğutma Pervanesini Takma” sayfa 109. Yedek pervane düzgün çalışıyorsa, sistemi kapatın. Bkz.
4 Sistem Kurulumu programına girin ve sistemin bellek ayarını kontrol edin. Bkz. “Bellek Ayarları Ekranı” sayfa 63. Gerekirse, bellek ayarlarında değişiklik yapın. Bellek ayarları takılı belleğe uygun olduğu halde yine de sorun görünüyorsa, adım 16 bölümüne gidin. 5 Sistemi ve bağlı çevre birimlerini kapatın ve sistemin fişini çekin. 6 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. 7 Mümkünse, ön kasa aksamını kaydırın. Bkz. “Ön Kasa Aksamı” sayfa 96. 8 Mümkünse, soğutma örtüsünü kaldırın. Bkz.
20 Belirtilmeyen arızalı bir bellek modülünde sorun giderme işlemi yapmak için, ilk DIMM soketindeki bellek modülünü aynı tür ve kapasiteye sahip bir modülle değiştirin. Bkz. “Bellek Modüllerini Takma” sayfa 103. 21 Mümkünse, soğutma örtüsünü yeniden yerleştirin. Bkz. “Soğutma Örtüsünü Takma” sayfa 95. 22 Mümkünse, ön kasayı geri kaydırın. Bkz. “Ön Kasa Aksamı” sayfa 96. 23 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83.
6 USB anahtarını bulun ve yeniden takın. Bkz. “Dahili USB Bellek Anahtarı” sayfa 112. 7 Mümkünse, soğutma örtüsünü yeniden yerleştirin. Bkz. “Soğutma Örtüsünü Takma” sayfa 95. 8 Mümkünse, ön kasayı geri kaydırın. Bkz. “Ön Kasa Aksamı” sayfa 96. 9 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 10 Sistemi ve bağlı çevre birimlerini açın, USB anahtarının çalışıp çalışmadığını kontrol edin. 11 Sorun çözülmezse, adım 2 ve adım 3'ü tekrarlayın.
NOT: Bir SD kart arızası meydana geldiğinde, dahili çift SD modülü denetleyicisi sisteme bilgi verir. Sonraki önyüklemede, sistem size arızayı belirten bir ileti gösterir. 5 SD kart 1 hata verdiyse, kartı SD kart yuvası 1'den çıkarın. Bkz. “Dahili Çift SD Modülünü Çıkarma” sayfa 132. SD kart 2 hata verdiyse, kartı SD kart yuvası 2'ye yeni bir SD kart takın ve adım 8'e geçin. 6 SD kart yuvası 2'de bulunan kartı çıkarın ve SD kart yuvası 1'e takın. Bkz.
Sorun Giderme - Optik Sürücü DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
Sorun Giderme - Sabit Sürücü DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
5 Sistemi yeniden başlatın, Sistem Kurulumu programına girin, denetleyicinin etkin olduğundan ve sürücülerin Sistem Kurulumu programında göründüğünden emin olun. Bkz. “Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma” sayfa 59. Sorun devam ederse, bkz. “Sorun Giderme - Depolama Denetleyicisi” sayfa 174. Sorun Giderme - Depolama Denetleyicisi NOT: SAS veya PERC denetleyicisi için sorun giderme işlemi yaparken, ayrıca bkz. işletim sisteminize ve denetleyiciye ait belgeler.
8 Pil destekli önbelleğe sahip bir PERC denetleyiciniz varsa RAID pilinin ve mümkünse, PERC kartının üzerindeki bellek modülünün düzgün takıldığından emin olun. 9 SAS arka paneli ile tümleşik depolama denetleyicisi arasındaki kablo bağlantılarının doğru olduğundan emin olun. Bkz. “Tümleşik Depolama Denetleyicisi Kartını Takma” sayfa 126 ve Şekil 6-4. Kabloların depolama denetleyicisine ve SAS arka panel kartına sıkıca takıldığından emin olun. 10 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83.
7 Sistemin fişini yeniden prize takın, sistemi ve takılı olan çevre birimlerini açın. 8 Sorun çözülmediyse, sistemi ve bağlı çevre birimlerini kapatın ve sistemin fişini çekin. 9 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. 10 Sisteme takılı olan tüm genişletme kartlarını çıkarın. Bkz. “Genişletme Kartını Çıkarma” sayfa 119. 11 Sistemi kapatın. Bkz. “Sistemi Kapatma” sayfa 83. 12 Sistemin fişini yeniden prize takın, sistemi ve takılı olan çevre birimlerini açın.
Sorun Giderme - İşlemciler DİKKAT: Çoğu onarım yalnızca yetkili bir servis teknisyeni tarafından yapılabilir. Sorun giderme işlemlerini ve basit onarımları yalnızca ürününüzün belgelerinde izin verildiği gibi ya da çevrimiçi hizmet veya telefon hizmeti ve destek ekibi tarafından belirtildiği gibi yapmalısınız. Dell tarafından yetkilendirilmemiş servislerden kaynaklanan zararlar garantinizin kapsamında değildir. Ürününüzle birlikte verilen güvenlik yönergelerini okuyun ve izleyin.
17 Uygun çevrimiçi tanılama sınamasını çalıştırın. Sınama hata verirse, işlemci arızalıdır. Bkz. “Yardım Alma” sayfa 195. 18 Sistemi ve bağlı çevre birimlerini kapatın ve sistemin fişini çekin. 19 Sistemi açın. Bkz. “Sistemi Açma” sayfa 82. 20 Soğutma pervanesi tertibatını sökün. Bkz. “Soğutma Pervanesi Tertibatını Sökme” sayfa 109. 21 İşlemci 1 ve işlemci 2'yi işlemci 3 ve işlemci 4'le değiştirin. Bkz. “İşlemciyi Çıkarma” sayfa 134. 22 Soğutma pervanesi tertibatını takın. Bkz.
Sistem Tanılama Araçlarını Çalıştırma Sisteminizde bir sorun olduğunu görürseniz, teknik yardımı aramadan önce tanılama araçlarını çalıştırın. Tanılama araçlarının amacı sisteminizin donanımını ek donanım veya veri kaybı riski olmaksızın sınamaktır. Sorunu kendiniz çözemezseniz, servis ve destek personeli sorunu çözmenizde yardımcı olmak için tanılama araçları sınama sonuçlarını kullanabilir.
Yerleşik Sistem Tanılama Özellikleri Sistem tanılama araçları özel aygıt grupları veya aygıtlar için bir dizi menü ve seçenek sunar.
Yerleşik Sistem Tanılama Araçlarını Çalıştırma Yerleşik sistem tanılama programı Yaşam Döngüsü Denetleyicisi ekranından çalıştırılır. DİKKAT: Yerleşik sistem tanılama araçlarını yalnızca sisteminizi sınamak için kullanın. Bu programı diğer sistemlerle kullanmak geçersiz sonuçlara ve hata iletilerine neden olabilir. 1 Sistem önyükleme yaparken, tuşuna basın. 2 Sol bölmedeki Tanılama Araçları'na ve sağ bölmedeki Tanılama Araçlarını Başlat'a tıklayın.
Özel Sınama Seçeneklerini Kullanma Ana Menü penceresinde Özel Sınama'yı seçtiğinizde, Özelleştir penceresi sınanacak aygıtları seçmenize, sınama için belirli seçenekleri belirlemenize ve sınama sonuçlarını görüntülemenize olanak tanır. Sınama İçin Aygıtları Seçme Özelleştir penceresinin sol tarafı sınanabilecek aygıtları gösterir. Bileşenlerini görüntülemek için bir aygıtın veya modülün yanındaki (+) işaretine tıklayın.
Bilgileri ve Sonuçları Görüntüleme Özelleştir penceresinde bulunan aşağıdaki sekmeler sınama ve sınama sonuçları hakkında bilgiler sunar: • Sonuçlar: Çalıştırılan sınamayı ve sonucu gösterir. • Hatalar: Sınama sırasında meydana gelebilecek hataları gösterir. • Yardım: Mevcut seçilen aygıt, bileşen veya sınama hakkındaki bilgileri gösterir. • Yapılandırma: Mevcut seçilen aygıt hakkındaki temel yapılandırma bilgilerini gösterir. • Parametreler: Sınama için ayarlayabileceğiniz parametreleri gösterir.
Sistem Tanılama Araçlarını Çalıştırma
Atlama Telleri ve Konnektörler Sistem Kartı Atlama Teli Bir şifreyi devre dışı bırakma hakkında bilgi için bkz. “Unutulan Bir Şifreyi Silme” sayfa 194. Tablo 6-1. Sistem Kartı Atlama Teli Ayarları Atlama Teli PWRD_EN Ayar Açıklama (varsayılan) Şifre özelliği etkindir (2-4. pinler) Şifre özelliği etkindir ve iDRAC6 yerel erişiminin kilidi sonraki AC güç dönüşümünde açılmıştır (4-6. pinler) NVRAM_CLR (varsayılan) Yapılandırma ayarları sistem önyüklemesinde korunur (3-5.
Sistem Kartı Konnektörleri Şekil 6-1.
Öğe Konnektör Açıklama 1 SLOT4_PCIE_G2_X8 yuva 4 PCIe - x8 bağlantı genişletme yuvası 2 SLOT3_PCIE_G2_X8 yuva 3 PCIe - x8 bağlantı genişletme yuvası 3 AMEA CONN iDRAC6 Enterprise kartı konnektörü 4 PWRD_EN Şifre etkinleştirme atlama teli NVRAM_CLR NVRAM silme atlama teli 5 MASER CONN iDRAC6 Express kartı konnektörü 6 Merkez PCIE_G2_X8 Genişletme kartı yükselticisi 1 konnektörü 7 PİL Pil soketi 8 SATA SATA güç konnektörü 9 FAN6 Sistem soğutma pervanesi 6 konektörü 10 FAN5 Si
Öğe Konnektör Açıklama C2 Bellek modülü yuvası C2 (beyaz serbest bırakma kolu) C6 Bellek modülü yuvası C6 C3 Bellek modülü yuvası C3 (beyaz serbest bırakma kolu) C7 Bellek modülü yuvası C7 C4 Bellek modülü yuvası C4 (beyaz serbest bırakma kolu) C8 Bellek modülü yuvası C8 15 CPU4 İşlemci 4 soketi 16 D1 Bellek modülü yuvası D1 (beyaz serbest bırakma kolu) D5 Bellek modülü yuvası D5 D2 Bellek modülü yuvası D2 (beyaz serbest bırakma kolu) D6 Bellek modülü yuvası D6 D3 Bellek modülü y
Öğe Konnektör Açıklama B4 Bellek modülü yuvası B4 (beyaz serbest bırakma kolu) B8 Bellek modülü yuvası B8 18 BP_PWR Arka panel gücü ve ön panel USB konnektörü 19 CPU2 İşlemci 2 soketi 20 FAN1 Sistem soğutma pervanesi 1 konektörü 21 FAN2 Sistem soğutma pervanesi 2 konektörü 22 PDB_CON Güç dağıtım kartı konnektörü 23 FAN3 Sistem soğutma pervanesi 3 konektörü 24 FAN4 Sistem soğutma pervanesi 4 konektörü 25 PWR_CONN Güç konnektörü 26 CTRL_PNL Kontrol paneli arabirimi konnektörü
SAS Arka Paneli Kart Konnektörleri Şekil 6-2.
Güç Dağıtım Kartı Konnektörleri Şekil 6-3.
Genişletme Kartı Yükselticisi Kart Bileşenleri ve PCle Veriyolları Şekil 6-4.
Şekil 6-5.
Unutulan Bir Şifreyi Silme Sistemin yazılım güvenlik özellikleri bir sistem şifresi ve bir kurulum şifresini içerir. Bunlar “Sistem Kurulumu Programını ve UEFI Önyükleme Yöneticisini Kullanma” sayfa 59 bölümünde ayrıntılı olarak incelenmiştir. Şifre atlama teli bu şifre özelliklerini etkinleştirir veya devre dışı bırakır ve kullanımdaki mevcut şifreleri siler. DİKKAT: Sistemle birlikte verilen güvenlik yönergelerindeki "Elektrostatik Boşalmaya Karşı Koruma" bölümüne bakın.
Yardım Alma Dell'e Başvurma ABD'deki müşterilerimiz 800-WWW-DELL (800-999-3355) numaralı telefonu arayabilir. NOT: Etkin bir Internet bağlantınız yoksa, başvuru bilgilerini satış faturanızda, irsaliyede, fişte veya Dell ürün kataloğunda bulabilirsiniz. Dell, çeşitli çevrimiçi ve telefonla destek ve hizmet seçenekleri sağlar. Bu hizmetlerin kullanılabilirliği ülkeye ve ürüne göre değişir ve bölgenizde bazı hizmetler verilemiyor olabilir.
Yardım Alma
Dizin B başlangıç sistem özelliklerine erişme, 13 bellek sorun giderme, 167 bellek anahtarı konnektörü (USB), 112 bellek modülleri (DIMM'ler) çıkarma, 105 takma, 103 yapılandırma, 99 boş güç kaynağı, 93 sabit sürücü, 84 çıkarma (devamı) sabit sürücüler, 86 sabit sürücüyü sürücü taşıyıcısından, 88 SAS arka panel kartı, 142 SAS denetleyicisi, 124 sistem kartı, 153 çalışırken takılabilir sabit sürücüler, 84 CD sürücüsü sorun giderme, 172 CD/DVD sürücüsü Bkz.
G İ garanti, 57 işlemci çıkarma, 134 takma, 138 yükseltmeler, 134 genişleme kartları çıkarma, 119 SAS denetleyicisi, 124 takma, 117 genişletme kartı sorun giderme, 175 genişletme yuvaları, 115 göstergeler güç, 14, 24 NIC, 23 ön panel, 14 güç göstergeleri, 14, 24 güç kaynakları çıkarma, 92 değiştirme, 93 göstergeler, 24 sorun giderme, 165 güvenlik, 159 iDRAC kartı takma, 129 iDRAC Yapılandırma Yardımcı Programı, 77 iletiler durum LCD'si, 25 hata iletileri, 60 sistem, 42 uyarı, 56 İşlemci Kartını Çıkarma
L P LCD paneli menüler, 17 özellikler, 16 pil SAS RAID kartı pili sorunlarını giderme, 174 pil (sistem) değiştirme, 140 M mikroişlemci Bkz.
sistem şifresi, 73 sistem başlangıç hatası, 159 sistem iletileri, 42 sistem kartı çıkarma, 153 takma, 156 sistem kurulumu seçenekler, 61 sistem kurulumu ekranları ana, 61 sistem kurulumu programı bellek ayarları, 63 girme, 60 güç yönetimi seçenekleri, 68 işlemci ayarları, 64 önyükleme ayarları, 65 PCI IRQ atamaları, 67 SATA ayarları, 65 seri iletişim seçenekleri, 67 sistem güvenliği seçenekleri, 69 tuş vuruşu, 60 tümleşik aygıt seçenekleri, 66 sistem özellikleri erişme, 13 sistem soğutması sorun giderme, 16
T takma bellek modülleri, 103 boş güç kaynağı, 93 boş sabit sürücü, 85 genişleme kartı, 117 güç kaynağı, 93 işlemci, 138 iDRAC kartı, 129 ön çerçeve, 81 optik sürücü, 89 sabit sürücüler, 87 SAS arka panel kartı, 144 SAS denetleyicisi, 126 tanılama araçları Dell PowerEdge Diagnostics'i kullanma, 179 gelişmiş sınama seçenekleri, 179 sınama seçenekleri, 180 USB bellek anahtarı için dahili konnektör, 112 ön panel konnektörleri, 14 USB anahtarı sorun giderme, 169-170 uyarı iletileri, 56 V video ön panel konnek
Dizin