Dell PowerEdge R830 オーナーズマニュアル 規制モデル: E21S Series 規制タイプ: E21S002 August 2020 Rev.
メモ、注意、警告 メモ: 製品を使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明しています。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 ©2014 - 2020 Dell Inc.またはその関連会社。All rights reserved.(不許複製・禁無断転載)Dell、EMC、およびその他の商標は、Dell Inc.
目次 章 1: Dell PowerEdge R830 の概要.....................................................................................................8 PowerEdge R830 システムでサポートされている構成................................................................................................8 前面パネル........................................................................................................................................................................... 10 2.5 インチハード ドライブシャーシ..................................................
章 5: プレオペレーティング システム管理アプリケーション.................................................................34 プレオペレーティングシステムアプリケーションを管理するためのオプション...............................................34 セットアップユーティリティ..........................................................................................................................................34 セットアップユーティリティの表示....................................................................................................................... 35 セットアップユーティリティ詳細.....................
プロセッサの取り付け.............................................................................................................................................. 100 ヒートシンクの取り付け...........................................................................................................................................102 電源装置ユニット............................................................................................................................................................ 103 ホットスペア機能........................
コントロールパネルの取り付け ............................................................................................................................. 157 システム基板.....................................................................................................................................................................159 システム ボードの取り外し..................................................................................................................................... 159 システム ボードの取り付け............................
診断メッセージ............................................................................................................................................................187 アラートメッセージ.................................................................................................................................................... 187 章 10: ヘルプ................................................................................................................................188 Dell EMC へのお問い合わせ.........................
1 Dell PowerEdge R830 の概要 Dell PowerEdge R830 は、8 ドライブまたは 16 ドライブベイシャーシ搭載の 2U ラックシステムで、次をサポートしています。 ● Intel Xeon E5-4600 v4 プロセッサ最大 4 台 ● DIMM 最大 48 個 ● ハードドライブまたはソリッドステートドライブ最大 16 台 メモ: お使いのシステムは、ホットスワップ対応のハードドライブのみをサポートします。 ● 電源装置ユニット最大 2 台 トピック: • • • • • PowerEdge R830 システムでサポートされている構成 前面パネル 背面パネル 前面パネルの診断インジケータ お使いのシステムのサービスタグの位置 PowerEdge R830 システムでサポートされている構成 Dell PowerEdge R830 システムは、次の構成をサポートしています。 8 Dell PowerEdge R830 の概要
図 1.
図 2. プロセッサ 4 個搭載の PowerEdge R830 システムでサポートされている構成 前面パネル 前面パネルでは、電源ボタン、NMI ボタン、システム識別タグ、システム識別ボタン、USB ポート、VGA ポートなど、サーバー前 面の機能ににアクセスできます。診断 LED または LCD パネルは、前面パネルに分かりやすく配置されています。ホットスワップ 対応のハードドライブには、前面パネルからアクセスできます。 2.
図 3. 前面パネルの機能(2.5 インチハード ドライブシャーシ) 1. 3. 5. 7. 9. 11. 電源ボタン システム識別ボタン LCD メニューボタン LCD パネル vFlash メディアカード スロット USB 管理ポート/iDRAC ダイレクト 2. 4. 6. 8. 10. 12. NMI ボタン ビデオコネクタ 情報タグ ハード ドライブ USB ポート 光学ドライブ 表 1. 前面パネルの機能(2.
表 1. 前面パネルの機能(2.5 インチハード ドライブシャーシ) (続き) アイテム インジケータ、ボタン、または アイコン コネクター 説明 5 LCD メニューボタン この LCD メニューボタンを押して、コントロール パネル LCD メ ニューを操作します。 6 情報タグ サービス タグ、NIC、MAC アドレスなどのシステム情報が表示 されます。 メモ: 情報タグは引き出し式のラベルパネルです。 7 LCD パネル システム ID、ステータス情報、システムエラーメッセージが表示 されます。詳細については、「LCD パネル」の項を参照してくだ さい。 8 ハード ドライブ サポートされているハードドライブの詳細については、「仕様詳 細」の項を参照してください。 9 vFlash メディアカード スロッ ト この vFlash メディアカード スロットを使用して、vFlash メディ アカードを挿入します。 10 USB 2.0 ポート USB 2.0 ポートを使用して、USB デバイスをシステムに接続しま す。このポートは 4 ピンで、USB 2.
図 4. LCD パネルの機能 表 2. LCD パネルの機能 アイテム ボタン 説明 1 左 カーソルが後方に 1 つ分移動します。 2 電源アイコンを カーソルによってハイライト表示されているメニュー項目を選択します。 3 右 カーソルが前方に 1 つ分移動します。 メッセージのスクロール中に次の操作ができます。 ● ボタンを押したままにして、スクロールの速度を上げます。 ● ボタンを放すと停止します。 メモ: ボタンを放すと、画面のスクロールが停止します。無活動の状態が 45 秒続くと、画面はスクロールを開始します。 ホーム画面の表示 [ホーム]画面には、システムに関するユーザー設定可能な情報が表示されます。この画面は、通常のシステムの操作中、ステータ ス メッセージやエラーがない場合に表示されます。システムがオフになり、エラーがない場合は、5 分間操作が行われないと LCD がスタンバイ モードになります。LCD をオンにするには、LCD の任意のボタンを押します。 手順 1.
オプション 説明 Simple(シンプル)を選択すると、LCD エラーメッセージが簡潔で分かりやすい説明で表示されます。エラ ーメッセージの詳細については、Dell.com/openmanagemanuals > OpenManage software(OpenManage ソフトウェア)で『Dell Event and Error Messages Reference Guide』(Dell イベントおよびエラーメッセージリ ファレンスガイド)を参照してください。 Set home(ホーム の設定) Home(ホーム)画面に表示されるデフォルト情報を選択します。Home(ホーム)画面でデフォルトとして 設定できるオプションおよびオプション項目については、「ビューメニュー」の項を参照してください。 関連参照文献 ビューメニュー 、p.
11. Ethernet ポート 13. USB 2.0 ポート 12. USB 3.0 ポート 表 3.
前面パネルの診断インジケータ メモ: システムの電源がオフの場合、診断インジケーターは点灯しません。システムを起動するには、機能している電源に差し 込み電源ボタンを押します。 表 4. 診断インジケータ アイコン 説明 状態 対応処置 ヘルスインジケー システムが良好な状態である場合 不要。 タ は、インジケータが青色に点灯しま す。 次の場合はインジケータが橙色に点 特定の問題については、「システムイベント ログ」また 滅します。 は「システムメッセージ」を参照してください。エラー メッセージの詳細については、Dell.
ハードドライブインジケータコード 各ハードドライブキャリアには、アクティビティインジケータとステータスインジケータがあります。これらのインジケータは、 ハードドライブの現在のステータスに関する情報を提供します。アクティビティ LED はハードドライブが使用中かどうかを示しま す。ステータス LED は、ハードドライブの電源状態を示します。 図 6. ハードドライブインジケータ 1. ハードドライブアクティビティインジケータ 2. ハードドライブステータスインジケータ 3. ハードドライブ メモ: ハードドライブが Advanced Host Controller Interface(AHCI)モードの場合、ステータスインジケータ(右側)は点灯しま せん。 表 5.
図 7. NIC インジケーター コード 1. リンクインジケータ 2. アクティビティインジケータ 表 6.
図 8. AC PSU ステータスインジケータ 1. AC PSU ステータスインジケータ / ハンドル 表 7.
図 9. DC PSU ステータスインジケータ 1.
2 マニュアルリソース 本項では、お使いのシステムのマニュアルリソースに関する情報を提供します。 マニュアル リソースの表に記載されているマニュアルを参照するには、次の手順を実行します。 ● Dell EMC サポート サイトにアクセスします。 1. 表の「場所」列に記載されているマニュアルのリンクをクリックします。 2. 目的の製品または製品バージョンをクリックします。 メモ: 製品名とモデルを確認する場合は、お使いのシステムの前面を調べてください。 3. [製品サポート]ページで、マニュアルおよび文書をクリックします。 ● 検索エンジンを使用します。 ○ 検索 ボックスに名前および文書のバージョンを入力します。 表 8. お使いのシステムのためのその他マニュアルのリソース タスク 文書 場所 システムのセットア ップ システムをラックに取り付けて固 www.dell.
表 8. お使いのシステムのためのその他マニュアルのリソース (続き) タスク 文書 場所 お使いのシステムで使用可能な iDRAC のバージョンを特定するに は、iDRAC Web インターフェイス で?、About の順にクリックします。 オペレーティング システムのイン ストールについての情報は、オペ レーティング システムのマニュア ルを参照してください。 www.dell.com/ operatingsystemmanuals ドライバおよびファームウェアの www.dell.com/support/drivers アップデートについての情報は、本 書の「ファームウェアとドライバを ダウンロードする方法」の項を参照 してください。 システムの管理 デルが提供するシステム管理ソフ トウェアについての情報は、『Dell OpenManage Systems Management 概要ガイド』を参照してください。 www.dell.com/poweredgemanuals OpenManage のセットアップ、使 www.dell.
表 8. お使いのシステムのためのその他マニュアルのリソース (続き) タスク 文書 場所 システムのトラブル シューティング PowerEdge サーバーの問題を特定し www.dell.
3 仕様詳細 本項では、お使いのシステムの仕様詳細と環境仕様の概要を示します。 トピック: • • • • • • • • • • • システムの寸法 シャーシの重量 プロセッサの仕様 PSU の仕様 システムバッテリの仕様 拡張バスの仕様 メモリの仕様 ドライブの仕様 ポートおよびコネクタの仕様 ビデオの仕様 環境仕様 システムの寸法 図 10.
表 9. PowerEdge R830 システムの寸法 X Xa Y Z(ベゼルを含 む) Zb(ベゼルを含 まない) Za(ベゼルを含 む) Za(ベゼルを含 まない) 482.4 mm(18.99 434.0 mm(17.08 86.8 mm(3.42 イ 777.6 mm(30.61 740.6 mm(29.16 35.7 mm(1.41 イ 20.4 mm(0.80 イ インチ) インチ) ンチ) インチ) インチ) ンチ) ンチ) シャーシの重量 表 10. シャーシの重量 システム 最大重量(すべてのハードドライブ /SSD を含む) 最小重量(ハードドライブなし) PowerEdge R830 31.7 kg(69.89 ポンド) 10.5 kg(23.15 ポンド) プロセッサの仕様 PowerEdge R830 システムは、最大 4 個の Intel Xeon E5-4600 v4 製品シリーズプロセッサをサポートします。 PSU の仕様 PowerEdge R830 システムは、最大 2 台の AC 冗長電源装置ユニット(PSU)をサポートします。 表 11.
表 12. メモリの仕様 メモリモジュールソケット メモリー容量 最小 RAM 48 個の DIMM ソケット デュアルプロセッサで 8 GB(各 4 基のプロセッサーで最大 6144 プロセッサに最低 1 枚のメモリ GB(LRDIMM) モジュール) ● 64 GB クアッドランク (LRDIMM) ● 8 GB シングル ランク (RDIMM) ● 16 Gb、または 32 GB デュア ルランク(RDIMM) 最大 RAM ドライブの仕様 ハードドライブ PowerEdge R830 システムは、SAS、SATA、または Nearline SAS ハードドライブをサポートしています。 表 13. PowerEdge R830 システムでサポートされているハードドライブオプション ハードドライブ 16 台のシステム 最大 16 台のホットスワップ対応 2.
シリアルコネクタ シリアルコネクタは、シリアルデバイスをシステムに接続します。PowerEdge R830 システムは、背面パネルでシリアルコネクタ 1 個をサポートしており、このコネクタは、9 ピンコネクタ、データ端末装置(DTE)、16550 準拠です。 VGA ポート ビデオグラフィックアレイ(VGA)ポートでは、システムを VGA ディスプレイに接続することができます。PowerEdge R830 シス テムは、前面および背面パネルで 15 ピン VGA ポートを 2 つサポートしています。 内蔵デュアル SD モジュール PowerEdge R830 システムは、内蔵デュアル SD モジュールを備えたオプションのフラッシュメモリカードスロットを 2 個サポート します。 メモ: カードスロット 1 個は冗長専用。 ビデオの仕様 PowerEdge R830 システムは、容量が 16 MB の Matrox G200eR2 グラフィックスカードをサポートしています。 表 15.
表 18. 最大振動の仕様 最大振動 仕様 動作時 0.26 Grms(5~350 Hz)(全稼働方向)。 保管時 1.88 Grms(10~500 Hz)で 15 分間(全 6 面で検証済)。 表 19. 最大衝撃の仕様 最大衝撃 仕様 動作時 x、y、z 軸の正および負方向に 6 連続衝撃パルス、11 ミリ秒以下で 6 G。 保管時 x、y、z 軸の正および負方向に 6 連続衝撃パルス(システムの各面に対 して 1 パルス)、2 ミリ秒以下で 71 G。 表 20. 最大高度の仕様 最大高度 仕様 動作時 30482000 m(10,0006560 フィート) 保管時 12,000 m(39,370 フィート) 表 21.
表 22. 粒子状汚染物質の仕様 (続き) 粒子汚染 仕様 腐食性ダスト ● 空気中に腐食性ダストが存在しないようにする必要があります。 ● 空気中の残留ダストは、潮解点が相対湿度 60% 未満である必要があ ります。 メモ: この条件は、データセンター環境と非データセンター環境に適 用されます。 表 23. ガス状汚染物質の仕様 ガス状汚染物 仕様 銅クーポン腐食度 クラス G1(ANSI/ISA71.04-1985 の定義による)に準じ、ひと月あたり 300 Å 未満。 銀クーポン腐食度 AHSRAE TC9.9 の定義に準じ、ひと月あたり 200 Å 未満。 メモ: 50% 以下の相対湿度で測定された最大腐食汚染レベル 標準動作温度 表 24. 動作時の標準温度の仕様 標準動作温度 仕様 継続動作(高度 950 m(3117 フィート)未満) 5~40°C(41~104°F)、装置への直射日光なし。 メモ: シャーシは最大 135 W のプロセッサをサポート。 動作時の拡張温度 表 25.
● ● ● ● 30 PCIe カードはスロット 1 とスロット 2 ではサポートされません。 135 W プロセッサ搭載のシステムでは、最大 8 台のハードドライブがサポートされています。 冗長電源ユニットが必要です。 デル認定外の周辺機器カードおよび / または 25 W を超える周辺機器カードは非対応です。 仕様詳細
4 システムの初期セットアップと設定 トピック: • • • システムのセットアップ iDRAC 設定 オペレーティング システムをインストールするオプション システムのセットアップ 次の手順を実行して、システムを設定します。 手順 1. システムを開梱します。 2. システムをラックに取り付けます。ラックへのシステムの取り付けの詳細については、システムの「ラック取り付けプレースマ ット」(Dell.com/poweredgemanuals)を参照してください。 3. 周辺機器をシステムに接続します。 4. システムを電源コンセントに接続します。 5. 電源ボタンを押す、または iDRAC を使用してシステムの電源を入れます。 6.
関連参照文献 LCD パネル 、p. 12 iDRAC へのログイン iDRAC には、次の資格でログインできます。 ● iDRAC ユーザー ● Microsoft Active Directory ユーザー ● Lightweight Directory Access Protocol(LDAP)ユーザー デフォルトのユーザー名とパスワードは、root と calvin です。シングル サイン オンまたはスマート カードを使用してログイン することもできます。 メモ: iDRAC にログインするには、iDRAC 資格情報が必要です。 iDRAC へのログイン、および iDRAC ライセンスの詳細については、Dell.
ドライバとファームウェアのダウンロード Dell EMC では、お使いのシステムに最新の BIOS、ドライバ、システム管理ファームウェアをダウンロードしてインストールするこ とを推奨しています。 前提条件 ドライバとファームウェアをダウンロードする前に、ウェブブラウザのキャッシュをクリアするようにしてください。 手順 1. 次を参照してください。 Dell.com/support/drivers. 2. Drivers & Downloads(ドライバおよびダウンロード)セクションで、Service Tag or Express Service Code(サービスタグま たはエクスプレスサービスコード)ボックスにお使いのシステムのサービスタグを入力し、Submit(送信)をクリックします。 メモ: サービスタグがない場合は、Detect My Product(製品の検出)を選択してシステムにサービスタグを自動的に検出 させるか、製品サポートでお使いの製品を選択します。 3.
5 プレオペレーティング システム管理アプリケー ション システムのファームウェアを使用して、オペレーティング システムを起動せずにシステムの基本的な設定や機能を管理することが できます。 トピック: • • • • • プレオペレーティングシステムアプリケーションを管理するためのオプション セットアップユーティリティ Dell Lifecycle Controller ブートマネージャ PXE 起動 プレオペレーティングシステムアプリケーションを管理す るためのオプション お使いのシステムには、プレオペレーティングシステムアプリケーションを管理するための次のオプションがあります。 ● ● ● ● セットアップユーティリティ ブートマネージャ Dell Lifecycle Controller Preboot Execution Environment(PXE) 関連概念 セットアップユーティリティ 、p. 34 ブートマネージャ 、p. 62 Dell Lifecycle Controller 、p. 62 PXE 起動 、p.
セットアップユーティリティの表示 System Setup(セットアップユーティリティ)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 関連概念 セットアップユーティリティ 、p. 34 関連参照文献 セットアップユーティリティ詳細 、p.
関連参照文献 システム BIOS 設定の詳細 、p. 36 起動設定 、p. 37 ネットワーク設定 、p. 39 システムセキュリティ 、p. 42 システム情報 、p. 45 メモリ設定 、p. 47 プロセッサ設定 、p. 48 SATA 設定 、p. 50 内蔵デバイス 、p. 54 シリアル通信 、p. 56 システムプロファイル設定 、p. 57 その他の設定 、p. 59 iDRAC 設定ユーティリティ 、p. 61 デバイス設定 、p. 62 関連タスク システム BIOS の表示 、p. 36 システム BIOS の表示 System BIOS(システム BIOS)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3.
オプション 説明 内蔵デバイス 内蔵デバイスコントローラとポートの管理、および関連する機能とオプションの指定を行うオプションを指 定します。 シリアル通信 シリアルポートの管理、および関連する機能とオプションの指定を行うオプションを指定します。 システムプロファ イル設定 プロセッサの電力管理設定、メモリ周波数などを変更するオプションを指定します。 システムセキュリ ティ システムパスワード、セットアップパスワード、Trusted Platform Module(TPM)セキュリティなどのシステ ムセキュリティ設定を行うオプションを指定します。システムの電源ボタンや NMI ボタンもこれで管理し ます。 その他の設定 システムの日時などを変更するオプションを指定します。 関連参照文献 システム BIOS 、p. 35 関連タスク システム BIOS の表示 、p. 36 起動設定 Boot Settings(起動設定) 画面を使用して、起動モードを BIOS または UEFI に設定します。起動順序を指定することも可能で す。 関連参照文献 システム BIOS 、p.
関連タスク 起動設定の詳細 、p. 38 起動順序の変更 、p.
● Unified Extensible Firmware Interface(UEFI) (デフォルト)の起動モードは、拡張 64 ビット起動インターフェイスです。UEFI モ ードで起動するようシステムを設定すると、システム BIOS の設定が置換されます。 1. System Setup Main Menu(セットアップユーティリティのメインメニュー)で、Boot Settings(起動設定)をクリックし、 Boot Mode(起動モード)を選択します。 2. 起動モードを選択し、このモードでシステム起動されるようにします。 注意: OS インストール時の起動モードが異なる場合、起動モードを切り替えるとシステムが起動しなくなることがありま す。 3.
関連参照文献 ネットワーク設定画面の詳細 、p. 40 UEFI iSCSI 設定の詳細 、p. 41 システム BIOS 、p. 35 関連タスク ネットワーク設定の表示 、p. 40 UEFI iSCSI 設定の表示 、p. 41 ネットワーク設定の表示 Network Settings(ネットワーク設定)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、Network Settings(ネットワーク設定)をクリックします。 関連参照文献 ネットワーク設定 、p.
UEFI iSCSI 設定 「iSCSI Settings(iSCSI 設定)」画面を使用して、iSCSI デバイスの設定を変更できます。iSCSI 設定オプションは UEFI 起動モードで のみ使用可能です。BIOS 起動モードでは、BIOS はネットワーク設定の制御を行いません。BIOS 起動モードの場合は、ネットワー クコントローラのオプション ROM がネットワーク設定を処理します。 関連参照文献 UEFI iSCSI 設定の詳細 、p. 41 関連タスク UEFI iSCSI 設定の表示 、p. 41 UEFI iSCSI 設定の表示 UEFI iSCSI Settings(UEFI iSCSI 設定)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3.
システムセキュリティ System Security(システムセキュリティ)画面を使用して、システムパスワードとセットアップパスワードの設定や、電源ボタン の無効化などの特定の機能を実行できます。 関連参照文献 セットアップパスワード使用中の操作 、p. 45 システム BIOS 、p. 35 関連タスク システムセキュリティ設定の詳細 、p. 42 システムセキュリティの表示 、p. 42 システムパスワードおよびセットアップパスワードの作成 、p. 43 システムを保護するためのシステムパスワードの使用 、p. 44 システムおよびセットアップパスワードの削除または変更 、p. 45 システムセキュリティの表示 System Security(システムセキュリティ)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2.
オプション TPM Security 説明 メモ: TPM メニューは、TPM モジュールがインストールされている場合のみ使用可能です。 TPM の報告モードを制御することができます。デフォルトでは、TPM セキュリティオプションは オフに設 定されています。TPM Status(TPM ステータス)、TPM Activation(TPM の有効化)、および Intel TXT のフ ィールドを変更できるのは、TPM ステータスフィールドが 起動前測定ありでオンまたは 起動前測定なしで オンのいずれかに設定されている場合に限られます。 TPM 情報 TPM の動作状態を変更することができます。このオプションは、デフォルトで変更なしに設定されていま す。 TPM Status TPM ステータスを指定します。 TPM Command 注意: TPM をクリアすると、TPM 内のすべてのキーが失われます。TPM キーが失われると、オペレー ティング システムの起動に影響するおそれがあります。 TPM の全コンテンツをクリアします。デフォルトでは、TPM のクリアーオプションはいいえに設定されて いま
手順 1. セットアップユーティリティを起動するには、システムの電源投入または再起動の直後に F2 を押します。 2. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > System Security(システムセキュリティ) の順にクリックします。 3. System Security(システムセキュリティ)画面で、Password Status(パスワードステータス)が Unlocked(ロック解除)に 設定されていることを確認します。 4. System Password(システムパスワード)フィールドに、システムパスワードを入力して、Enter または Tab を押します。 以下のガイドラインに従ってシステムパスワードを設定します。 ● パスワードの文字数は 32 文字までです。 ● 0 から 9 までの数字を含めることができます。 ● 特殊文字は、次の文字のみが利用可能です:スペース、(”)、(+)、(,)、(-)、(.)、(/)、(;)、([)、(\)、(])、(`)。 システムパスワードの再入力を求め
システムおよびセットアップパスワードの削除または変更 前提条件 メモ: Password Status(パスワードステータス)が Locked(ロック)に設定されている場合、既存のシステムパスワードま たはセットアップパスワードを削除または変更することはできません。 手順 1. セットアップユーティリティを起動するには、システムの電源投入または再起動の直後に F2 を押します。 2. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > System Security(システムセキュリティ) の順にクリックします。 3. System Security(システムセキュリティ)画面で Password Status(パスワードステータス)が Unlocked(ロック解除)に 設定されていることを確認します。 4. System Password(システムパスワード)フィールドで、既存のシステムパスワードを変更または削除して、Enter または Tab を押します。 5.
関連タスク システム情報の表示 、p. 46 システム情報の表示 System Information(システム情報)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 System Information(システム情報)をクリックします。 関連参照文献 システム情報 、p.
オプション 説明 UEFI Compliance システムファームウェアの UEFI 準拠レベルを指定します。 Version(UEFI 準拠 バージョン) 関連参照文献 システム情報 、p. 45 システム情報の詳細 、p. 46 関連タスク システム情報の表示 、p. 46 メモリ設定 Memory Settings(メモリ設定)画面を使用して、メモリの設定をすべて表示し、メモリのテストやノードのインターリービング など特定のメモリ機能を有効または無効にできます。 関連参照文献 メモリ設定の詳細 、p. 47 システム BIOS 、p. 35 関連タスク メモリ設定の表示 、p. 47 メモリ設定の表示 Memory Settings(メモリ設定)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2.
オプション 説明 システムメモリの サイズ システム内のメモリサイズを指定します。 システムメモリの タイプ システムに取り付けられているメモリのタイプを指定します。 システムメモリ速 度 メモリの速度を指定します。 システムメモリ電 圧 メモリの電圧を指定します。 ビデオメモリ ビデオメモリの容量を指定します。 システムメモリテ スト システム起動時にメモリ テストを実行するかどうかを指定します。オプションは Enabled(有効)および Disabled(無効)です。このオプションは、デフォルトで Disabled(無効)に設定されています。 メモリ動作モード メモリの動作モードを指定します。使用可能なオプションは、オプティマイザ モード、アドバンス ECC モ ード、ミラー モード、スペア モード、スペア+アドバンス ECC モード、Dell 耐障害性モード、Dell NUMA 耐 障害性モードです。デフォルトでは、このオプションは Optimizer Mode(最適化モード)に設定されてい ます。 メモ: メモリ動作モードオプションには、お使いのシステムのメモリ構成に基づ
手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で Processor Settings(プロセッサ設定)をクリックします。 関連参照文献 プロセッサ設定 、p. 48 プロセッサー設定の詳細 、p.
オプション 説明 設定可能 TDP システムの電力および温度送出機能に基づいて、POST 中にプロセッサーの熱設計電力(TDP)のレベルを 再設定することができます。TDP は冷却システムが熱分散に必要な最大熱量を確認します。このオプショ ンは、デフォルトで Nominal に設定されています。 メモ: このオプションは、プロセッサーの特定の最小在庫管理単位(SKU)でのみ利用可能です。 X2Apic モード X2Apic モードを有効または無効にします。 Dell Controlled Turbo ターボ エンゲージメントを制御します。このオプションは、システム プロファイルがパフォーマンスに設定 されている場合のみ有効になります。 メモ: インストールされている CPU の数に応じて、最大 4 台のプロセッサのリストがあります。 プロセッサーあた りのコア数 プロセッサーごとの有効なコアの数を制御します。このオプションは、デフォルトですべてに設定されてい ます。 プロセッサー 64 ビ プロセッサが 64 ビット拡張をサポートするかどうかを指定します。 ットサポート プロセッサー コア
SATA 設定の表示 SATA Settings(SATA 設定)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 SATA Settings(SATA 設定)をクリックします。 関連参照文献 SATA 設定 、p. 50 関連タスク SATA 設定の詳細 、p.
オプション 説明 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブなどのリムーバブル メディアデバイスに対しては未定義です。 Port C(ポート C) 選択されたデバイスのドライブタイプを設定します。Embedded SATA settings(組み込み SATA 設定)が ATA モードに設定されている場合、BIOS サポートを有効にするには、このフィールドを Auto(自動)に設 定する必要があります。BIOS サポートをオフにするには、OFF(オフ)に設定します。 AHCI または RAID モードの場合、BIOS のサポートは常に有効です。 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacit
オプション 説明 オプション 説明 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブなどのリムーバブル メディアデバイスに対しては未定義です。 Port G(ポート G) 選択されたデバイスのドライブタイプを設定します。Embedded SATA settings(組み込み SATA 設定)が ATA モードに設定されている場合、BIOS サポートを有効にするには、このフィールドを Auto(自動)に設 定する必要があります。BIOS サポートをオフにするには、OFF(オフ)に設定します。 AHCI または RAID モードの場合、BIOS のサポートは常に有効です。 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブなど
オプション 説明 オプション 説明 Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブなどのリムーバブル メディアデバイスに対しては未定義です。 関連参照文献 SATA 設定 、p. 50 関連タスク SATA 設定の表示 、p. 51 内蔵デバイス Integrated Devices(内蔵デバイス)画面を使用して、ビデオコントローラ、内蔵 RAID コントローラ、および USB ポートを含むす べての内蔵デバイスの設定を表示し設定することができます。 関連参照文献 システム BIOS 、p. 35 関連タスク 内蔵デバイスの詳細 、p. 54 内蔵デバイスの表示 、p. 54 内蔵デバイスの表示 Integrated Devices(内蔵デバイス)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2.
オプション 説明 USB 3.0 Setting USB 3.0 のサポートを有効または無効にします。お使いの OS が USB 3.0 をサポートしている場合のみ、この (USB 3.0 の設定) オプションを有効にします。このオプションを無効にすると、デバイスは USB 2.0 速度で動作します。USB 3.
オプション 説明 Slot Disablement システムで利用可能な PCIe スロットを有効または無効にします。スロット無効化機能を使用して、指定の (スロット無効化) スロットに取り付けられている PCIe カードの構成を制御できます。スロットの無効化は、取り付けられて いる周辺機器(拡張)カードによって OS の起動が妨げられているか、またはシステムの起動の遅延が生じ ている場合のみに限定する必要があります。スロットが無効になると、Option ROM と UEFI ドライバの両方 が無効になります。 関連参照文献 内蔵デバイス 、p. 54 関連タスク 内蔵デバイスの表示 、p. 54 シリアル通信 Serial Communication(シリアル通信)画面を使用して、シリアル通信ポートのプロパティを表示します。 関連参照文献 システム BIOS 、p. 35 関連タスク シリアル通信の詳細 、p. 56 シリアル通信の表示 、p. 56 シリアル通信の表示 Serial Communication(シリアル通信)画面を表示するには、次の手順を実行してください。 手順 1.
オプション Serial Communication (シリアル通信) 説明 BIOS でシリアル通信デバイス(シリアルデバイス 1 およびシリアルデバイス 2)を選択します。BIOS コン ソールリダイレクトを有効にして、ポートアドレスを指定できます。このオプションは、デフォルトで Auto (自動)に設定されています。 Serial Port シリアルデバイスのポートアドレスを設定することができます。このオプションはデフォルトで Serial Address(シリアル Device 1=COM2, Serial Device 2=COM1(シリアルデバイス 1 = COM2、シリアルデバイス 2 = COM1) に ポートアドレス) 設定されています。 メモ: シリアルオーバー LAN(SOL)機能にはシリアルデバイス 2 のみ使用できます。SOL でコンソール のリダイレクトを使用するには、コンソールのリダイレクトとシリアルデバイスに同じポートアドレス を設定します。 メモ: システムを起動するたびに、BIOS は iDRAC で保存された設定でシリアル MUX を同期します。シ リアル MUX 設
システムプロファイル設定の表示 、p. 58 システムプロファイル設定の表示 System Profile Settings(システムプロファイル設定)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 System Profile Settings(システムプロファイル設定)をクリックします。 関連参照文献 システムプロファイル設定 、p. 57 関連タスク システムプロファイル設定の詳細 、p.
オプション 説明 Collaborative CPU CPU 自動設定オプションを有効または無効にします。有効に設定すると、CPU 電源管理が OS DBPM および Performance システムの DBPM(DAPC)によって制御されます。このオプションは、デフォルトで Disabled(無効)に Control(CPU パフ 設定されています。 ォーマンス協調制 御) Memory Patrol メモリ巡回スクラブの周波数を設定することができます。デフォルトでは、このオプションは Standard(標 Scrub(メモリ巡回 準)に設定されています。 スクラブ) Memory Refresh メモリリフレッシュレートを 1x または 2x に設定します。このオプションは、デフォルトで 1x に設定されて Rate(メモリリフレ います。 ッシュレート) Uncore Frequency Processor Uncore Frequency(プロセッサアンコア周波数)オプションを選択することが可能になります。 (アンコア周波数) Dynamic mode(動的モード)では、プロセッサの実行時のコアお
その他の設定の表示 Miscellaneous Settings (その他の設定)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 Miscellaneous Settings(その他の設定)をクリックします。 関連参照文献 その他の設定 、p. 59 関連タスク その他の設定の詳細 、p.
オプション 説明 有効にすると、ISC(インシステムキャラクタライゼーション)はシステムの設定で関連する変更を検出する POST 中に実行され、システムの電力とパフォーマンスを最適化します。ISC の実行には約 20 秒かかり、ISC の結果を適用するにはシステムのリセットが必要です。Enabled - No Reboot(有効 - 再起動なし)オプシ ョンで ISC を実行すると、次回にシステムをリセットするまで ISC の結果は適用されずに続行されます。 Enabled(有効)オプションで ISC を実行すると、システムは即時に強制リセットされ、ISC の結果が適用 されます。システムのリセットが強制的に実行されるため、システムの準備が整うまでに時間がかかりま す。無効にすると、ISC は実行されません。 関連参照文献 その他の設定 、p. 59 関連タスク その他の設定の表示 、p.
● デフォルトの温度プロファイル設定 ● 最大パフォーマンス(パフォーマンス最適化) ● 最小電力(1 ワットあたりのパフォーマンス最適化) 3. USER COOLING OPTIONS(ユーザー冷却オプション)で、Fan Speed Offset(ファン速度オフセット)、Minimum Fan Speed (最小ファン速度)、および Custom Minimum Fan Speed(カスタム最小ファン速度)を設定します。 4. Back(戻る) > Finish(終了) > Yes(はい) の順にクリックします。 関連参照文献 iDRAC 設定ユーティリティ 、p. 61 デバイス設定 Device Settings(デバイス設定)では、デバイスパラメータを設定することができます。 関連参照文献 システム BIOS 、p.
ブートマネージャの表示 Boot Manager(ブートマネージャ)を起動するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたら を押します。 F11 = Boot Manager F11 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、もう一度 システムを起動してやり直してください。 関連参照文献 ブートマネージャ 、p. 62 起動マネージャのメインメニュー 、p.
システムユーティリティ System Utilities(システム ユーティリティ)には、起動可能な次のユーティリティが含まれています。 ● 診断プログラムの起動 ● BIOS/UEFI アップデート ファイル エクスプローラー ● システムの再起動 メモ: 選択する起動モードに応じて、BIOS または UEFI アップデート ファイル エクスプローラーの場合があります。 関連参照文献 ブートマネージャ 、p.
6 システムコンポーネントの取り付けと取り外し トピック: • • • • • • • • • • • • • • • • • • • • • • • • • • 安全にお使いいただくために システム内部の作業を始める前に システム内部の作業を終えた後に 推奨ツール 前面ベゼル(オプション) システムカバー システムの内部 プロセッサ拡張モジュール(オプション) 冷却エアフローカバー 冷却ファン 冷却ファンアセンブリ システムメモリ プロセッサとヒートシンク 電源装置ユニット 内蔵ストレージコントローラカード 拡張カードと拡張カードライザー IDSDM ネットワークドーターカード 内蔵 USB メモリキー(オプション) システムバッテリー ハードドライブ 光学ドライブ(オプション) ハードドライブバックプレーン コントロールパネル システム基板 Trusted Platform Module 安全にお使いいただくために メモ: システムを持ち上げる必要がある場合は、誰かの手を借りてください。けがを防ぐため、決してシステムを 1 人で持ち上 げようとしないでください。 警告: システムの電源が入っている状態
システム内部の作業を始める前に 前提条件 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1. システムとすべての周辺機器の電源を切ります。 2. システムを電源コンセントと周辺機器から外します。 3. 前面ベゼルが取り付けられている場合は、取り外します。 4. 必要に応じて、システムをラックから取り外します。 詳細については、Dell.com/poweredgemanuals のラック取り付けプレースマットを参照してください。 5. システムのカバーを外します。 システム内部の作業を終えた後に 前提条件 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1. システムカバーを取り付けます。 2. 必要に応じて、システムをラックに取り付けます。 詳細については、Dell.com/poweredgemanuals のラック取り付けプレースマットを参照してください。 3. 前面ベゼルを取り外した場合は、取り付けます。 4. 周辺機器を再度接続し、システムをコンセントに接続します。 5.
オプションの前面ベゼルの取り外し 前提条件 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1. ベゼルキーの位置を確認して取り外します。 メモ: ベゼルキーはベゼルの背面に取り付けられています。 2. キーを使ってベゼルのロックを解除します。 3. リリースラッチを上にスライドさせて、ベゼルの左端を引きます。 4. 右端のフックを外し、ベゼルを取り外します。 図 11. オプションの前面ベゼルの取り外し a. リリースラッチ b. ベゼルロック c. 前面ベゼル 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク オプションの前面ベゼルの取り付け 、p.
手順 1. ベゼルキーの位置を確認して取り外します。 メモ: ベゼルキーはベゼルの背面に取り付けられています。 2. ベゼルの右端をシャーシに取り付けます。 3. ベゼルのもう一方の端をシステムにはめ込みます。 4. キーを使用してベゼルをロックします。 図 12. オプションの前面ベゼルの取り付け a. ベゼルロック b. 前面ベゼル 関連参照文献 安全にお使いいただくために 、p. 65 システムカバー システムカバーはシステム内部のコンポーネントを保護すると共に、システム内の通気を維持するのに役立ちます。システムカバ ーを取り外すと、イントルージョンスイッチが作動します。 システムカバーの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. オプションのベゼルが取り付けられている場合は、取り外します。 手順 1. ラッチリリースロックを反時計方向に回してロック解除位置にします。 2.
図 13. システムカバーの取り外し a. システムカバー b. ラッチ c. ラッチリリースロック 次の手順 1. システムカバーを取り付けます。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク オプションの前面ベゼルの取り外し 、p. 67 システムカバーの取り付け 、p. 69 システムカバーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. すべての内部ケーブルが接続され、邪魔にならないように束ねられており、システム内部に工具や余分な部品が残っていないこ とを確認します。 手順 1. システムカバーのスロットをシャーシのタブに合わせます。 2.
システムカバーを前方にスライドさせると、システムカバーのスロットがシャーシのタブにはめ込まれます。システムカバーが シャーシのタブに完全にはめ込まれると、システムカバーラッチが所定の位置にロックされます。 3. ラッチリリースロックを時計方向に回してロック位置にします。 図 14. システムカバーの取り付け a. システムカバー b. ラッチ c. ラッチリリースロック 次の手順 1. 2. 3. 4. 前面ベゼルを取り外した場合は、取り付けます。 周辺機器を再度接続し、システムをコンセントに接続します。 システムとすべての周辺機器の電源を入れます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク オプションの前面ベゼルの取り外し 、p.
図 15. システムの内部 - プロセッサ 2 個搭載のシステム 1. 3. 5. 7. 9. 冷却ファン(6) DIMM(12) PSU コネクタ ライザー 2 DIMM(12) 2. 4. 6. 8.
図 16. システム内部 - プロセッサ拡張モジュール(PEM)があるプロセッサ 4 個搭載のシステム 1. 3. 5. 7. 9. 冷却ファン(6) システム基板および PEM 上の DIMM(24) PSU コネクタ ライザー 2 システム基板 2. 4. 6. 8. 10.
手順 1. PEM(プロセッサ拡張モジュール)がシャーシから外れるまで PEM のリリースレバーを上げます。 図 17. PEM の取り外し a. プロセッサ拡張モジュール b. リリースレバー 2. リリースレバーとサポートピンを持って、PEM を持ち上げシャーシから取り外します。 図 18. PEM の取り外し a. プロセッサ拡張モジュール b.
3. PEM を取り外したままにする場合は、QPI コネクタの上にフィラーブラケットを取り付け、冷却用エアフローカバーを取り付け ます。 メモ: FCC(Federal Communications Commission)認可規格にシステムを準拠させるには、QPI コネクタの上にフィラーブラ ケットを取り付ける必要があります。フィラーブラケットはシステム内へのごみやほこりの侵入を防ぎます。 4. フィラーブラケットを取り付けるには、フィラーブラケット上の切り込みを QPI コネクタのスタンドオフに合わせ、フィラーブ ラケットを所定の位置に押し入れます。 図 19. QPI コネクタへのフィラーブラケットの取り付け a. フィラーブラケット b. スタンドオフ(2) 5. PEM 電源コネクタキャップを取り付けます。 次の手順 1. 冷却用エアフローカバーが取り付けられていた場合は、取り付けます。 注意: 冷却用エアフローカバーを取り外した状態でプロセッサ 2 基のシステムを使用しないでください。システムが急激に オーバーヒートする可能性があり、システムのシャットダウンや、データ損失の原因となります。 2.
2. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 3. 「システム内部の作業を始める前に」の項に記載された手順に従います。 4. 冷却用エアフローカバーが取り付けられていれば、外します。冷却用エアフローカバーは将来使用するために取っておきます。 手順 1. 該当する場合は、フィラーブラケットを取り外します。フィラーブラケットを取り外すには、タブを持ちフィラーブラケットを 持ち上げて、QPI コネクタから取り外します。 図 20. QPI コネクタからのフィラーブラケットの取り外し a. フィラーブラケット b. スタンドオフ(2) 2. 該当する場合は、PEM 電源コネクタキャップを取り外します。 3.
図 21. PEM の取り付け 1. QPI コネクタ 3. PEM 電源コネクタ(2) 5. サポートピン(2) 2. 突起(3) 4. 位置合わせガイド(2) 6. リリースレバー 4. PEM が所定の位置にロックされるまで、リリースレバーをシャーシの方向に押します。 図 22. リリースレバーを使用したシャーシへの PEM の固定 a. プロセッサ拡張モジュール b. サポートピン(2) c.
次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 2. 初めてプロセッサ拡張モジュールを取り付ける場合は、 を押してセットアップユーティリティを起動し、プロセッサの情 報が新しいシステム構成と一致していることを確認します。 3. システム Diagnostics(診断)プログラムを実行し、新しいプロセッサが正しく動作することを確認します。利用できる Diagnostics(診断)テストについては「システム Diagnostics(診断)プログラムの使い方」を参照してください。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
冷却エアフローカバー 冷却エアフローカバーは、システム全体にわたって空気力学的に空気の流れを導きます。空気の流れは、システムのすべての重要 なパーツを通過します。減圧により、ヒートシンクの表面領域全体で空気が引き込まれ、冷却効果が向上します。 冷却エアフローカバーの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 注意: 冷却エアフローカバーをせずに、プロセッサーが 2 基あるシステムを動作させないでください。システムが急激にオー バーヒートする可能性があり、システムのシャットダウンや、データ ロスの原因となります。 1.
次の手順 1. 冷却エアフローカバーを取り付けます。 2. 必要な場合は、フルレングス PCIe カードを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り付け 、p. 79 システム内部の作業を終えた後に 、p. 66 冷却エアフローカバーの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2.
図 24. 冷却エアフローカバーの取り付け 1. シャーシ上のスロット(4) 3. 冷却エアフローカバー 2. タッチポイント(2) 4. 冷却エアフローカバーのガイドスロット(4) 次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
冷却ファンの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載されている安全ガイドラインに従ってください。 2.
関連タスク システム内部の作業を始める前に 、p. 66 冷却ファンの取り付け 、p. 82 システム内部の作業を終えた後に 、p. 66 冷却ファンの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載されている安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 メモ: 各ファンの取り付け手順は同じです。 手順 1. 冷却ファンの底部にあるコネクタをシステム ボードのコネクタに合わせます。 2. タブが所定の位置にロックされるまで、冷却ファンを固定スロットに挿入します。 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
図 26. 冷却ファンアセンブリーの取り外し 1. 冷却ファン アセンブリー 3. リリースレバー(2) 5. 冷却ファンコネクタ(6) 2. 冷却ファン(6) 4. システム ボード上のガイドピン(2) 6. シャーシのガイドピン(6) 次の手順 1. 冷却ファン アセンブリーを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却ファンアセンブリーの取り付け 、p. 83 システム内部の作業を終えた後に 、p.
注意: 冷却ファン アセンブリーを取り付ける前に、ケーブルが正しく接続され、ケーブル保持ブラケットによって支えられてい ることを確認します。ケーブルが正しく取り付けられていないと、損傷するおそれがあります。 手順 1. 冷却ファン アセンブリーのスロットをシャーシのガイドピンに合わせます。 2. 冷却ファン アセンブリーをシャーシに挿入します。 3. リリースレバーを下げて、冷却ファン アセンブリーをシャーシにロックし、確実に装着します。 図 27. 冷却ファンアセンブリーの取り付け 1. 冷却ファン アセンブリー 3. リリースレバー(2) 5. 冷却ファンコネクタ(6) 2. 冷却ファン(6) 4. システム ボード上のガイドピン(2) 6. シャーシのガイドピン(6) 次の手順 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
メモ: MT/s は DIMM の速度単位で、MegaTransfers/ 秒の略語です。 メモリバスの動作周波数は 1866 MT/s、2133 MT/s、2400 MT/s で、以下の要因に応じて異なります。 ● DIMM のタイプ(RDIMM または LRDIMM) ● 各チャネルに装着されている DIMM の数 ● 選択されているシステムプロファイル(たとえば、Performance Optimized(パフォーマンス重視の構成)、Custom(カスタム)、 または Dense Configuration Optimized(高密度設定最適化)) ● プロセッサでサポートされている DIMM の最大周波数 お使いのシステムにはメモリソケットが 24 個あり、12 個ずつの 2 セット(各プロセッサに 1 セット)に分かれています。ソケッ ト 12 個の各セットは、4 つのチャネルで構成されています。どのチャネルも、最初のソケットのリリースタブは白、2 番目のソケ ットのタブは黒、3 番目のソケットのタブは緑に色分けされています。 図 28.
図 29. プロセッサ拡張モジュール上のメモリソケットの位置 メモリチャネルの構成は次のとおりです。 表 28. メモリチャネル プロセッサ チャネル 0 チャネル 1 チャネル 2 チャネル 3 プロセッサ スロット A1、A5、および A9 スロット A2、A6、および 1 A10 スロット A3、A7、および A11 スロット A4、A8、および A12 プロセッサ スロット B1、B5、および B9 スロット B2、B6、および 2 B10 スロット B3、B7、および B11 スロット B4、B8、および B12 プロセッサ スロット C1、C5、および 3 C9 スロット C2、C6、および C10 スロット C3、C7、および C11 スロット C4、C8、および C12 プロセッサ スロット D1、D5、および D9 スロット D2、D6、および 4 D10 スロット D3、D7、および D11 スロット D4、D8、および D12 次の表は、サポートされている構成のメモリ装着と動作周波数を示しています。 表 29.
表 29. メモリ装着 (続き) DIMM のタイ 装着 DIMM/ チャネ プ ル LRDIMM 電圧 動作周波数(単位: MT/s) 最大 DIMM ランク / チャネル 3 1866 デュアルランクまたはシング ルランク 1 2400、2133、1866 クアッドランク 2400、2133、1866 クアッドランク 2133、1866 クアッドランク 2 1.
メモリ最適化独立チャネルモード このモードでは、使用するデバイス幅が x4 のメモリモジュールについてのみ Single Device Data Correction(SDDC)がサポートされ ます。スロット装着に関する特定の要件はありません。 メモリスペアリング メモ: メモリスペアリングを使用するには、セットアップユーティリティでこの機能を有効にする必要があります。 このモードでは、各チャネルにつき 1 ランクがスペアとして予約されます。いずれかのランクで修正可能なエラーが絶えず検知さ れる場合、そのランクからのデータがスペア ランクにコピーされ、障害の発生したランクは無効になります。 メモリ スペアリングを有効にすると、オペレーティング システムに使用できるシステムメモリはチャネルごとに 1 ランク少なくな ります。たとえば、4 GB のシングル ランク メモリ モジュールを 16 個使用するデュアル プロセッサー構成では、利用可能なシステ ムメモリは 16(メモリ モジュール)× 4 GB = 64 GB とはならず、3/4(ランク/チャネル)× 16(メモリ モジュール)× 4 GB = 48 G
表 31.
表 31.
表 31. メモリ構成 – プロセッサ 2 基 (続き) システムの容量(GB) 2560 DIMM のサイズ (GB) 128 DIMM の枚数 DIMM のランク、構成、周 装着する DIMM スロット 波数 20 4R x4、2133 MT/s 4R x4、1866 MT/s 3072 128 24 4R x4、2133 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、B1、B2、B3、B4、 B5、B6、B7、B8、B9、B10 4R x4、1866 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A12、B1、 B2、B3、B4、B5、B6、B7、B8、 B9、B10、B11、B12 DIMM の枚数 機構と速度 装着する DIMM スロット 4 1R x8、1866 MT/s A1、B1、C1、D1 表 32.
表 32.
表 32.
図 30. メモリモジュールの取り外し a. メモリモジュール b. メモリモジュールソケット c. メモリモジュールソケットのイジェクタ(2) 次の手順 1. メモリモジュールを取り付けます。 メモ: メモリモジュールを取り外したままにする場合は、メモリモジュールのダミーカードを取り付けます。 2. 冷却エアフローカバーを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 メモリモジュールの取り付け 、p. 94 システム内部の作業を終えた後に 、p.
手順 1. 該当するメモリモジュールソケットの位置を確認します。 注意: 各モジュールは、カードの端だけを持ち、メモリモジュールの中央部や金属の接触部に触れないように取り扱ってく ださい。 2. メモリモジュールソケットのイジェクタを外側に向かって開き、メモリモジュールをソケットに挿入できる状態にします。 3. メモリモジュールのエッジコネクタをメモリモジュールソケットの位置合わせキーに合わせ、メモリモジュールをソケット内に 挿入します。 注意: メモリモジュールの中央にかけないようにしてください。メモリモジュールの両端に均等に力を加えてください。 メモ: メモリモジュールソケットには位置合わせキーがあり、メモリモジュールをソケットに一方向でしか取り付けられな いようになっています。 4. ソケットレバーが所定の位置にしっかりと収まるまで、メモリモジュールを親指で押し込みます。 メモリモジュールがソケットに適切に装着されると、メモリモジュールソケットのレバーがメモリモジュールが装着されている 別のソケットのレバーと同じ位置に揃います。 図 31. メモリモジュールの取り付け a. メモリモジュール b.
冷却エアフローカバーの取り付け 、p. 79 システム内部の作業を終えた後に 、p. 66 プロセッサとヒートシンク 次の作業は下記の手順に従って行ってください。 ● ヒートシンクの取り外しと取り付け ● 追加のプロセッサの取り付け ● プロセッサの交換 メモ: 正常な冷却状態を維持するために、空のプロセッサソケットすべてにプロセッサダミーを取り付ける必要があります。 ヒートシンクの取り外し 前提条件 注意: プロセッサを取り外す場合を除き、ヒートシンクをプロセッサから取り外さないでください。ヒートシンクは適切な温度 条件を保つために必要です。 警告: ヒートシンクは高温で触れません。システムの電源を切った後、時間を取って、ヒートシンクを冷却してください。 1. 2. 3. 4. 5. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 フルレングス PCIe カードが取り付けられている場合は、取り外します。 冷却エアフローカバーを取り外します。 #2 プラスドライバを準備しておきます。 手順 1.
3. プロセッサシールド 4. 固定ネジスロット(4) 次の手順 1. ヒートシンクおよびプロセッサを取り付けます。 2. プロセッサーとヒートシンクを交換します。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 システム内部の作業を終えた後に 、p.
4. プロセッサシールドのタブを持ち、 オープンファースト ソケットリリースレバーが持ち上がるまで、プロセッサシールドを持ち 上げます。 注意: ソケットピンは壊れやすく、損傷して修復できなくなることがあります。プロセッサをソケットから取り外す際に は、ソケットのピンを曲げないように気をつけてください。 5. プロセッサを持ち上げてソケットから外し、オープンファーストソケットリリースレバーを上げ たままにしておきます。 メモ: プロセッサを取り外したままにする場合は、ソケットピンを保護してソケットにほこりが入らないように空のソケッ トにソケット保護キャップを取り付ける必要があります。 メモ: プロセッサーを取り外したら、再利用、返品、または一時的な保管のために静電気防止パッケージに入れておきます。 プロセッサの底部に触れないでください。プロセッサは側面の端以外に触れないでください。 図 33. プロセッサシールド 1. クローズファーストソケットリリースレバー 3. プロセッサ 5. アンロックアイコン 98 システムコンポーネントの取り付けと取り外し 2. ロックアイコン 4.
図 34. プロセッサの取り外し 1. 3. 5. 7. クローズファーストソケットリリースレバー プロセッサ プロセッサシールド ソケット 2. 4. 6. 8. プロセッサのピン 1 インジケータ スロット(4) オープンファーストソケットリリースレバー ソケットキー(4) 次の手順 1. 2. 3. 4. プロセッサを取り付けます。 ヒートシンクを取り付けます。 冷却用エアフローカバーを取り付けます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 ヒートシンクの取り外し 、p. 96 ヒートシンクの取り付け 、p. 102 冷却エアフローカバーの取り付け 、p. 79 システム内部の作業を終えた後に 、p.
プロセッサの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 #2 プラスドライバを準備しておきます。 システムをアップグレードする場合は、最新バージョンのシステム BIOS を Dell.
12. 同様に、オープンファーストソケットリリースレバー(アンロックアイコン 込んで固定します。 の近くにあります)を下げて、タブの下に押し 図 35. プロセッサの取り付け 1. 3. 5. 7. ソケットリリースレバー 1 プロセッサ プロセッサシールド プロセッサソケット 2. 4. 6. 8. プロセッサのピン 1 の角 スロット(4) ソケットリリースレバー 2 タブ(4) 次の手順 メモ: プロセッサを取り付けた後は、必ずヒートシンクを取り付けてください。ヒートシンクは適切な温度条件を保つために必 要です。 ヒートシンクを取り付けます。 PCIe 拡張カードライザーが取り外されている場合は、再度取り付けます。 ケーブルが外されている場合は、拡張カードに再度接続します。 「システム内部の作業を終えた後に」に記載された手順に従います。 起動時に F2 を押してセットアップユーティリティを起動し、プロセッサの情報が新しいシステム構成と一致していることを確 認します。 6. システム診断プログラムを実行し、新しいプロセッサが正しく動作することを確認します。 1. 2. 3. 4. 5.
ヒートシンクの取り付け 、p. 102 システム内部の作業を終えた後に 、p. 66 ヒートシンクの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 プロセッサーを取り付けます。 #2 プラスドライバを準備しておきます。 手順 1. 既存のヒートシンクを使用している場合は、糸くずの出ない清潔な布で、ヒートシンクからサーマルグリースを拭き取ります。 2.
4. 4 本のうち 1 本のネジを締めて、ヒートシンクをシステム基板に固定します。 5. 残りの 2 本のネジについても同じ手順を繰り返します。 図 37. ヒートシンクの取り付け 1. 固定ネジ(4) 3. プロセッサシールド 2. ヒートシンク 4. 固定ネジスロット(4) 次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 2. 起動時に F2 を押してセットアップユーティリティを起動し、プロセッサの情報が新しいシステム構成と一致していることを確 認します。 3. システム診断プログラムを実行し、新しいプロセッサが正しく動作することを確認します。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 プロセッサの取り付け 、p. 100 システム内部の作業を終えた後に 、p.
ホットスペア機能 お使いのシステムではホットスペア機能がサポートされており、電源装置ユニット(PSU)の冗長性に関連する電力のオーバーヘッ ドが大幅に軽減されます。 ホットスペア機能を有効に設定すると、冗長 PSU のうち 1 台がスリープ状態に切り替わります。アクティブな PSU が負荷の 100% を支えるため、効率良く動作します。スリープ状態の PSU は、アクティブな PSU の出力電圧を監視します。アクティブな PSU の出力電圧が低下すると、スリープ状態の PSU がアクティブな出力状態に戻ります。 1 台の PSU をスリープ状態にするよりも、両方の PSU をアクティブする方が効率的な場合は、アクティブな PSU でスリープ状態 の PSU をアクティブにできます。 デフォルトの PSU 設定は次の通りです。 ● アクティブな PSU の負荷が 50% を超えている場合、冗長 PSU はアクティブ状態に切り替えられます。 ● アクティブな PSU の負荷が 20% を下回った場合、冗長 PSU はスリープ状態に切り替えられます。 iDRAC 設定を使用してホットスペア機能を設定できます。iDR
次の手順 PSU、または PSU ダミーを取り付けます。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク 電源装置ユニットダミーの取り付け 、p. 105 電源装置ユニットダミーの取り付け 電源装置ユニット(PSU)ダミーを 2 つ目の PSU ベイにのみ取り付けます。 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 電源装置ユニットダミーを電源装置ユニットスロットに合わせて、所定の位置にカチッと収まるまでダミーを電源装置ユニットス ロットに押し込みます。 図 39. PSU ダミーの取り付け a.
AC 電源装置ユニットの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 注意: システムが正常に動作するには、PSU 1 台が必要です。冗長電源が装備されたシステムでも、システムに電源が入った 状態で一度に取り外しと取り付けができる PSU は 1 台だけです。 PSU の取り外しに支障がある場合は、必要に応じて、オプションのケーブル管理アームのラッチを外して持ち上げます。ケーブル 管理アームの詳細については、システムのラックに関するマニュアルを参照してください。 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1.
AC 電源装置ユニットの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: 最大出力電力(ワット数で表記)は PSU ラベルに記載されています。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 冗長電源ユニット(PSU)をサポートしているシステムでは、2 台の PSU のタイプと最大出力電力が同じになるようにします。 3. PSU のダミーが取り付けられている場合は、取り外します。 手順 1. PSU が完全に装着され、リリースラッチが所定の位置にカチッとおさまるまで、PSU をシャーシに差し込みます。 2.
内蔵ストレージコントローラカード お使いのシステムには、システム基板上に内蔵ストレージコントローラカード専用の拡張カードスロットがあります。内蔵ストレー ジコントローラカードは、システムの内蔵ハードドライブ用の内蔵ストレージサブシステムを提供します。コントローラは SAS と SATA ハードドライブをサポートし、RAID 構成のハードドライブをセットアップすることもできます。RAID 構成は、システムに含 まれるストレージコントローラのバージョンによって異なります。コントローラは SAS ハードドライブをサポートしています。 内蔵ストレージコントローラカードの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。
3. 次の手順を実行して、カードに接続されているケーブルを外します。 a. SAS ケーブルコネクタのラッチを押します。 b. コネクタから SAS ケーブルを引き出します。 4. 拡張カードを取り外したままにする場合は、フィラーブラケットを取り付けます。 次の手順 1. 該当する場合は、内蔵ストレージコントローラカードを取り付けます。 メモ: H330、H730、H730P、または HBA330 カードが、拡張カードライザーのスロット番号 7 のみに取り付けられているこ とを確認します。 2. 冷却エアフローカバーを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 内蔵ストレージコントローラカードの取り付け 、p. 109 冷却エアフローカバーの取り付け 、p. 79 システム内部の作業を終えた後に 、p.
図 43. 内蔵ストレージコントローラカードの取り付け 1. 内蔵ストレージコントローラカード 3. ライザー 3 2. 拡張カードラッチ 4. SAS ケーブル 5. SAS データケーブルを内蔵ストレージコントローラカードの SAS データケーブルコネクタに接続します。 メモ: ケーブルは、必ずケーブルのコネクタラベルの表記に従って接続してください。向きが逆の場合、正しく動作しませ ん。 6. SAS データケーブルをシステム基板に接続します。 次の手順 1. 拡張カードライザー 1 を取り付けます。 2. 冷却用エアフローカバーが取り付けられていた場合は、取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 冷却エアフローカバーの取り付け 、p. 79 拡張カードライザー 1 への拡張カードの取り付け 、p. 121 システム内部の作業を終えた後に 、p.
拡張カードと拡張カードライザー システム内の拡張カードは、システム基板上の拡張スロットに挿入可能なアドオンカード、あるいは拡張バスを介してシステムに 拡張機能を追加するライザーカードです。 メモ: 拡張カードライザーがサポートされていない、または欠落している場合は、システムイベントログ(SEL)イベントが記 録されます。システムへの電源投入には支障がなく、BIOS POST メッセージも F1/F2 一時停止も表示されません。 拡張カードの取り付けガイドライン システムの設定に応じて、次の PCI Express(PCIe)Generation 3 拡張カードがサポートされます。 表 33.
表 34.
図 44. 拡張カードライザー 1 の取り外し 1. 拡張カードライザー 1 3. ライザーガイド(右) 5. ライザーガイド(左) 2. タッチポイント(2) 4. 拡張カードライザー 1 コネクタ 図 45. 拡張カードライザー 1 上のコネクタ a. 拡張カードコネクタスロット 1 b.
図 46. 拡張カードライザー 2 の取り外し 1. 拡張カードライザー 2 3. ライザーガイド(右) 5. 拡張カードライザー 2 コネクタ 図 47. 拡張カードライザー 2 上の コネクタ a. 拡張カードコネクタスロット 3 b. 拡張カードコネクタスロット 4 c. 拡張カードコネクタスロット 5 114 システムコンポーネントの取り付けと取り外し 2. タッチポイント(2) 4.
図 48. 拡張カードライザー 3 の取り外し 1. 拡張カードライザー 3 3. 拡張カードライザー 3 コネクタ 5. ライザーガイド(左) 2. シャーシのガイドピン 4. ライザーガイド(右) 図 49. 拡張カードライザー 3 上の コネクタ a. シャーシイントルージョンスイッチ b. 拡張カードコネクタスロット 6 c.
次の手順 1. 拡張カードが取り外されている場合、拡張カードをライザーに取り付けます。 2. 該当する場合、拡張カードライザーを交換します。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザーの取り付け 、p. 116 システム内部の作業を終えた後に 、p. 66 拡張カードライザーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3.
図 50. 拡張カードライザー 1 の取り付け 1. 拡張カードライザー 1 3. ライザーガイド(背面) 5. ライザーガイド前面 2. タッチポイント(2) 4.
図 51. 拡張カードライザー 2 の取り付け 1. 拡張カードライザー 2 3. ライザーガイド(右) 5. 拡張カードライザー 2 コネクタ 118 システムコンポーネントの取り付けと取り外し 2. タッチポイント(2) 4.
図 52. 拡張カードライザー 3 の取り付け 1. 拡張カードライザー 3 3. 拡張カードライザー 3 コネクタ 5. ライザーガイド背面 2. シャーシのガイドピン 4. ライザーガイド前面 次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 2. カードのマニュアルに従って、必要なすべてのデバイスドライバをインストールします。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザーの取り外し 、p. 112 システム内部の作業を終えた後に 、p.
2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. 拡張カードライザーのタッチポイントを持ち、ライザーを持ち上げてシャーシから取り出します。 手順 1. 拡張カードに接続されているケーブルをすべて外します。 2. 拡張カードの固定ラッチを押し、拡張カードライザー引き出して開きます。 3. 拡張カードのリリースラッチを引いて開きます。 4. 拡張カードの端をつかんで、拡張カードコネクタから取り外します。 5. 拡張カードを取り外したままにする場合は、空の拡張スロットの開口部に金属製のフィラーブラケットを取り付け、拡張カード ラッチを閉じます。 メモ: システムシステム、空の拡張カード スロットにフィラーブラケットを取り付ける必要があります。ブラケットはゴミ や埃からシステムを保護し、システム内部の冷却と通気を効率化します。フィラーブラケットは適切な温度条件を保つため に必要です。 6. 拡張カードのリリースラッチを押して閉じます。 7. 拡張カードの固定ラッチをスロットに向けて閉じます。 図 53. 拡張カードライザー 1 からの拡張カードの取り外し 1. 3. 5. 7.
関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 1 への拡張カードの取り付け 、p. 121 システム内部の作業を終えた後に 、p. 66 拡張カードライザー 1 への拡張カードの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. 拡張カードライザー 1 を取り外します。 手順 1.
3. タッチポイント(2) 5. 拡張カード 7. 拡張カードライザータブ 4. 拡張カード固定ラッチ 6. 拡張カードリリースラッチ 5. 拡張カードのリリースラッチを押して閉じます。 6. 拡張カードの固定ラッチをスロットに向けて閉じます。 次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 2. カードのマニュアルに従って、カードに必要なすべてのデバイスドライバをインストールします。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 1 からの拡張カードの取り外し 、p. 119 システム内部の作業を終えた後に 、p.
図 55. 拡張カードライザー 2 からの拡張カードの取り外し 1. 拡張カードライザー 2 3. タッチポイント(2) 5. 拡張カード 2. 拡張カードコネクタ 4. 拡張カードラッチ 次の手順 1. 拡張カードライザー 2 を取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 2 への拡張カードの取り付け 、p. 123 システム内部の作業を終えた後に 、p.
2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. 拡張カードライザー 2 を取り外します。 手順 1. 該当する場合は、拡張カードを開梱して取り付けの準備をします。手順については、カードに付属のマニュアルを参照してくだ さい。 2. 拡張カードラッチを開き、フィラーブラケットを取り外します。 3. カードの両端を持って、カードエッジコネクタをカードが完全に装着されるまで拡張カードコネクタにしっかりと差し込みます。 図 56. 拡張カードライザー 2 への拡張カードの取り付け 1. 拡張カードライザー 2 3. タッチポイント(2) 5. 拡張カード 2. 拡張カードコネクタ 4. 拡張カードラッチ 4. 拡張カードのラッチをスロットに向けて閉じます。 次の手順 1. 拡張カードライザー 2 を取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 3. カードのマニュアルに従って、カードに必要なすべてのデバイスドライバをインストールします。 関連参照文献 安全にお使いいただくために 、p.
拡張カードライザー 3 からの拡張カードの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. 拡張カードライザーのタッチポイントを持ち、ライザーを持ち上げてシャーシから取り出します。 手順 1. 拡張カードに接続されているケーブルをすべて外します。 2. 拡張カード固定ラッチを開きます。 メモ: フルハイト拡張カードを取り外している場合は、拡張カードホルダを開きます。 3. 拡張カードの端をつかんで、拡張カードコネクタから取り外します。 4.
図 58. 拡張カードライザー 3 からのフルハイト拡張カードの取り外し 1. 拡張カードホルダ 3. 拡張カードコネクタ 2. 拡張カード 4. 拡張カードライザー 3 次の手順 1. 拡張カードライザー 3 を取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 3 への拡張カードの取り付け 、p. 126 システム内部の作業を終えた後に 、p.
手順 1. 該当する場合は、拡張カードを開梱して取り付けの準備をします。 手順については、カードに付属のマニュアルを参照してください。 2. 拡張カード固定ラッチを開きます。 3. カードの両端を持って、カードエッジコネクタをカードが完全に装着されるまで拡張カードコネクタにしっかりと差し込みます。 4. フルハイト拡張カードを取り付けている場合は、拡張カードホルダーを拡張カードライザーの方へ引き出します。拡張カードホ ルダーの溝の間に拡張カードが収まっていることを確認します。 5. 拡張カードライザーのラッチをスロットに向けて閉じます。 図 59. 拡張カードライザー 3 へのハーフハイト拡張カードの取り付け 1. 拡張カード 3. 拡張カードコネクタ 2. 拡張カード固定ラッチ 4.
図 60. 拡張カードライザー 3 へのフルハイト拡張カードの取り付け 1. 拡張カードホルダ 3. 拡張カードコネクタ 2. 拡張カード 4. 拡張カードライザー 3 次の手順 1. 必要に応じて、ケーブルを拡張カードに接続します。 2. カードのマニュアルに従って、カードに必要なすべてのデバイスドライバをインストールします。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 3 からの拡張カードの取り外し 、p. 125 システム内部の作業を終えた後に 、p.
内蔵 SD カードの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: 各 SD カードに、取り外す前の対応するスロット番号のラベルを一時的に貼り付けてください。SD カードを再度取り付け る際は、その対応するスロットに取り付けます。 手順 内蔵デュアル SD モジュール上の SD カードスロットの位置を確認し、カードを押してスロットから外します。 図 61. 内蔵 SD カードの取り外し 1. IDSDM 3. SD カード 2 5.
内蔵 SD カードの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: お使いのシステムで SD カードを使用するには、システム セットアップで内蔵 SD カード ポートが有効に設定されている ことを確認します。 メモ: 各 SD カードに、取り外す前の対応するスロット番号のラベルを一時的に貼り付けてください。SD カードを再度取り付け る際は、その対応するスロットに取り付けます。 手順 1.
関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p. 66 オプションの内蔵デュアル SD モジュールの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3.
表 35. IDSDM インジケータコード (続き) 表記規則 IDSDM インジケータコード 説明 C 橙色の点滅 カードの不一致またはカードに障害が発生したことを示しま す。 D 橙色 カードがオフライン、故障している、または書き込みが禁止 されていることを示します。 E 消灯 カードが取り付けられていないか、起動していないことを示 します。 次の手順 1. IDSDM をインストールします。 2. 取り外した場合は、SD カードを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 内蔵 SD カードの取り外し 、p. 129 オプションの内蔵デュアル SD モジュールの取り付け 、p. 132 内蔵 SD カードの取り付け 、p. 130 システム内部の作業を終えた後に 、p.
図 64. オプションの内蔵デュアル SD モジュールの取り付け a. IDSDM b. プルタブ c. IDSDM コネクタ 次の手順 1. SD カードを取り付けます。 メモ: SD カードは、取り外し時に付けたラベルに基づいて前と同じスロットに取り付けてください。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 内蔵 SD カードの取り付け 、p. 130 システム内部の作業を終えた後に 、p. 66 ネットワークドーターカード ネットワーク ドーター カード(NDC)は小型の取り外し可能なメザニン カードです。NDC を使用すると、さまざまなネットワーク 接続(たとえば、4 x 1GbE、2 x 10GbE、および 2 x コンバージド ネットワーク アダプタなど)を柔軟に選択できます。 ネットワークドーターカードの取り外し 前提条件 1. 2. 3. 4.
修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. ネットワークドーターカード(NDC)をシステム基板に固定している固定ネジを緩めます。 2. タッチポイント両側にある端部を使って NDC を持ち、カードを持ち上げてシステム基板のコネクタから取り外します。 3. イーサネットコネクタが背面パネルのスロットから取り出されるまで、ネットワークドータカードをシステム背面から引き出し ます。 4. NDC を持ち上げてシャーシから取り出します。 図 65. NDC の取り外し 1. ネジソケット(2) 3. 固定ネジ(2) 5. ネットワークドーターカード(NDC) 2. システム基板上のコネクタ 4. タッチポイント(2) 6. イーサネットコネクタ用の背面パネルスロット 次の手順 1. NDC を取り付けます。 2. 拡張カードライザー 1 が取り外されている場合は、取り付けます。 3.
ネットワークドーターカードの取り付け 、p. 135 拡張カードライザー 2 からの拡張カードの取り外し 、p. 122 システム内部の作業を終えた後に 、p. 66 ネットワークドーターカードの取り付け 前提条件 1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 該当する場合は、拡張カードライザー 1 を取り外します。 #1 プラスドライバを準備しておきます。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1.
次の手順 1. 拡張カードライザー 1 を取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 拡張カードライザー 2 からの拡張カードの取り外し 、p. 122 拡張カードライザー 1 への拡張カードの取り付け 、p. 121 システム内部の作業を終えた後に 、p.
図 68. 内蔵 USB メモリー キーの取り付け a. USB メモリー キー b. USB ポート 次の手順 1. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 2. 起動中に、F2 を押して System Setup を起動し、システムが USB メモリー キーを検出していることを確認します。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
図 69. システムバッテリの取り外し a. システムバッテリ b. システムバッテリスロット 3. 新しいシステムバッテリを取り付けるには、プラス側を上にしてバッテリを持ち、固定タブの下に挿入します。 4. 所定の位置に収まるまでバッテリをコネクタに押し込みます。 図 70. システムバッテリの取り付け a. システムバッテリ b. システムバッテリスロット 次の手順 1. 冷却エアフローカバーを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 3. 起動中に F2 を押して System Setup(セットアップユーティリティ)を起動し、バッテリが正常に動作していることを確認しま す。 4. セットアップユーティリティの Time(時刻)および Date(日付)フィールドで正しい時刻と日付を入力します。 5. System Setup(セットアップユーティリティ)を終了します。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p.
います。正しいドライブクラスを選択すると、品質、機能、パフォーマンス、および信頼性という重要な領域をターゲット向けに 最適化することができます。 メモ: Enterprise クラスのハードドライブをエントリーハードドライブと併用しないでください。 右側のドライブタイプの選択は、使用パターンに応じて異なります。不適切なエントリーハードドライブの使用(年間 55 TB を超 える作業負荷率)は大きなリスクにつながり、ドライブ故障率を増加させます。 これらのハードドライブに関する詳細は、Dell.
図 71. ホットスワップ対応ハードドライブまたは SSD の取り外し a. リリースボタン b. ハードドライブまたは SSD キャリア c. ハードドライブまたは SSD キャリアのハンドル 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 オプションの前面ベゼルの取り外し 、p.
3. ハードドライブキャリア前面のリリースボタンを押して、ハードドライブキャリアのハンドルを開きます。 4. ハードドライブキャリアがバックプレーンに接続されるまで、キャリアをハードドライブスロットに挿入します。 5. ハードドライブのキャリアハンドルを閉じて、ハードドライブを所定の位置にロックします。 図 72. ホットスワップ対応ハードドライブまたは SSD の取り付け a. リリースボタン b. ハードドライブまたは SSD キャリア c. ハードドライブまたは SSD キャリアのハンドル 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク ホットスワップ対応ハードドライブまたはソリッドステートドライブの取り外し 、p. 139 ハードドライブキャリアへのハードドライブまたはソリッドステートドライブの取り付け 、p. 143 2.
図 73. 2.5 インチハードドライブダミーの取り外し a. ハードドライブダミー b. リリースボタン 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク オプションの前面ベゼルの取り外し 、p. 67 2.5 インチハードドライブダミーの取り付け 、p. 142 2.5 インチハードドライブダミーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 前面ベゼルが取り付けられている場合は、取り外します。 手順 リリースボタンが所定の位置にカチッと収まるまで、ハードドライブダミーをハードドライブスロットに差し込みます。 図 74. 2.5 インチハードドライブダミーの取り付け a. ハードドライブダミー 次の手順 前面ベゼルを取り外した場合は、取り付けます。 関連参照文献 安全にお使いいただくために 、p.
関連タスク オプションの前面ベゼルの取り外し 、p. 67 オプションの前面ベゼルの取り付け 、p. 67 2.5 インチハードドライブダミーの取り外し 、p. 141 ハード ドライブキャリアーからのハード ドライブまたはソリッドステー トドライブの取り外し 前提条件 1. #1 プラスドライバを準備しておきます。 2. システムからホット スワップ対応ハード ドライブ キャリアーを取り外します。 手順 1. ハード ドライブキャリアーのスライドレールからネジを外します。 2. ハード ドライブを持ち上げてハード ドライブキャリアーから取り出します。 図 75. ハード ドライブキャリアーからのハード ドライブの取り外し a. ネジ(4) b. ハード ドライブ c. ハード ドライブキャリアー 次の手順 該当する場合は、ハード ドライブをハード ドライブキャリアーに取り付けます。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク ハードドライブキャリアへのハードドライブまたはソリッドステートドライブの取り付け 、p.
3. ネジを取り付けて、ハードドライブをハードドライブキャリアに固定します。 図 76. ハードドライブキャリアへのハードドライブの取り付け a. ネジ(4) b. ハードドライブ c. ハードドライブキャリア 次の手順 ホットスワップ対応ハードドライブキャリアを取り付けます。 関連参照文献 安全にお使いいただくために 、p.
図 77. オプションの光学ドライブの取り外し a. 光学ドライブ b. 電源 / データケーブル c. リリースタブ 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 スリム光学ドライブダミーの取り付け 、p. 147 システム内部の作業を終えた後に 、p. 66 光学ドライブの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2.
図 78. オプションの光学ドライブの取り付け a. 光学ドライブ b. 電源 / データケーブル c. リリースタブ 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p. 66 スリム光学ドライブダミーの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 手順 1.
図 79. スリム光学ドライブダミーの取り外し a. スリム光学ドライブダミー b. 光学ドライブダミーロック 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 スリム光学ドライブダミーの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載されている安全手順に従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 手順 1. スリム光学ドライブダミーをスリム光学ドライブベイに揃えます。 2.
図 80. スリム光学ドライブダミーの取り付け 1. スリム光学ドライブダミー 2. 光学ドライブダミーロック 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を終えた後に 、p. 66 ハードドライブバックプレーン お使いのシステムは以下をサポートしています。 ● 2.5 インチ(x16)SAS/SATA バックプレーン、または ● 2.5 インチ(x8)SAS/SATA バックプレーン ハードドライブバックプレーンの取り外し 前提条件 1. 2. 3. 4. 5.
手順 1. バックプレーンから SAS/SATA データ、信号、電源ケーブルを外します。 2. リリースタブを押し、バックプレーンを上方向に持ち上げて、シャーシの背面に向かってスライドさせます。 図 81. 2.5 インチ(x16)SAS/SATA バックプレーンの取り外し 1. 3. 5. 7. 9. フック(3) ハードドライブバックプレーン バックプレーン信号ケーブル SAS ケーブル(2) バックプレーン上のハードドライブコネクタ 2. 4. 6. 8.
図 82. ケーブル配線図 — 2.5 インチ(x16)SAS/SATA バックプレーン 1. 3. 5. 7. 9. 150 バックプレーン上の通信コネクタ PERC カード上の SAS B コネクタ システム基板 システム基板上の信号コネクタ バックプレーン上の SAS A コネクタ システムコンポーネントの取り付けと取り外し 2. 4. 6. 8. 10.
図 83. 2.5 インチ(x8)SAS/SATA バックプレーンの取り外し 1. 3. 5. 7. 9. バックプレーン上のハードドライブコネクタ フック(3) リリースタブ SAS ケーブル(2) ミニ SAS コネクタ(2) 2. 4. 6. 8.
図 84. ケーブル配線図 — 2.5 インチ(x8)SAS/SATA バックプレーン 1. 3. 5. 7. 9. バックプレーン上の通信コネクタ PERC カード上の SAS B コネクタ システム基板 システム基板上の信号コネクタ ハードドライブバックプレーン 2. 4. 6. 8. 10. ケーブル固定ブラケット PERC カード上の SAS A コネクタ ケーブル固定ブラケット バックプレーン上の SAS B コネクタ バックプレーン上の SAS A コネクタ 次の手順 1. 2. 3. 4. 5. ハードドライブバックプレーンを取り付けます。 冷却ファンアセンブリを取り付けます。 冷却エアフローカバーを取り付けます。 すべてのハードドライブを取り付けます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 冷却エアフローカバーの取り外し 、p. 78 冷却ファンアセンブリーの取り外し 、p.
ハードドライブ 、p. 138 システム内部の作業を終えた後に 、p. 66 ハードドライブバックプレーンの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. SAS/SATA/SSD のデータ、信号、および電源ケーブルをバックプレーンに接続します。 2. シャーシのフックをガイドとして使用し、ハードドライブバックプレーンの位置を合わせます。 3.
図 86. 2.5 インチ(x8)SAS/SATA バックプレーンの取り付け 1. 3. 5. 7. 9. バックプレーン上のハードドライブコネクタ フック(3) リリースタブ SAS ケーブル(2) ミニ SAS コネクタ(2) 2. 4. 6. 8. ハードドライブバックプレーン 固定スロット(3) バックプレーン電源ケーブル バックプレーン信号ケーブル 次の手順 1. ハードドライブを元の場所に取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 ハードドライブ 、p. 138 システム内部の作業を終えた後に 、p. 66 コントロールパネル コントロールパネルには、電源ボタン、診断インジケータ、前面 USB ポートが含まれています。 コントロールパネルの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3.
注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. #2 プラスドライバを使用して、コントロールパネルをシャーシに固定しているネジを外します。 注意: コントロールパネルを外す際に無理な力を加えないように注意してください。コネクタが損傷するおそれがありま す。 2. コントロールパネルをシステム基板を接続しているすべてのケーブルを外します。 メモ: USB 電源ケーブルを取り外す前に、冷却ファンアセンブリを取り外すようにしてください。 3. システムの内側からコントロールパネルを押してシャーシから取り外します。 図 87. コントロールパネルの取り外し 1. コントロールパネル 3.
図 88. vFlash コネクタ /USB コネクタモジュールの取り外し i. vFlash コネクタ /USB コネクタモジュール ii. ネジ(2) iii. コントロールパネルコネクタケーブル 5. 情報タグのタブの位置を確認し、タブを押します。 6. 情報タグをスロットから押し出し、コントロールパネルから取り外します。 メモ: 情報タグは新しいコントロールパネルに取り付けるために取っておきます。 図 89. 情報タグの取り外し a. 情報タグ b. タブ c. スロット 次の手順 1. vFlash コネクタ /USB コネクタモジュールを取り付けます。 2. コントロールパネルを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p.
関連タスク システム内部の作業を始める前に 、p. 66 コントロールパネルの取り付け 、p. 157 システム内部の作業を終えた後に 、p. 66 コントロールパネルの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. #2 プラスドライバを準備しておきます。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1.
メモ: USB 電源ケーブルを取り付ける前に、冷却ファンアセンブリを取り外すようにしてください。 5. コントロールパネルをシャーシ内のスロットに挿入し、モジュールをネジで固定します。 図 91. コントロールパネルの取り付け 1. コントロールパネル 3. コントロールパネルコネクタケーブル 2. ネジ(2) 4. USB コネクタケーブル 図 92. 情報タグの取り付け a. 情報タグ b. タブ c. スロット 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 安全にお使いいただくために 、p.
関連タスク システム内部の作業を始める前に 、p. 66 システム内部の作業を終えた後に 、p.
3. システム ボードをシャーシから持ち手取り外します。 図 93. システム ボードの取り外し a. 蝶ネジ b. システム ボードホルダー c. システム ボード 次の手順 1. システム ボードを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム ボードの取り付け 、p. 160 システム内部の作業を終えた後に 、p. 66 システム ボードの取り付け 前提条件 1.
2. 「システム内部の作業を始める前に」の項に記載されている手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. 新しいシステム ボードアセンブリーのパッケージを開きます。 注意: システム基板は、メモリモジュール、プロセッサ、またはその他のコンポーネントを持って持ち上げないでください。 注意: システム ボードをシャーシに取り付ける際には、システム識別ボタンに損傷を与えないように注意してください。 2. タッチポイントを持って、システム ボードをシャーシ内に下します。 3. 所定の位置にカチッと固定されるまで、システム ボードをシャーシの後方へ押し込みます。 図 94.
メモ: TPM プラグイン モジュールがシステム ボードに取り付けられているため、取り外せません。TPM プラグイン モジ ュールが取り付けられた場合、TPM プラグイン モジュールを交換するとシステム ボードをすべて交換することになります。 2. 次のコンポーネントを取り付けます。 a. ケーブル固定ブラケット b. PCIe カードホルダー c. 内蔵ストレージコントローラー カード d. 内蔵 USB キー(該当する場合) e. 内蔵デュアル SD モジュール f. すべての拡張カードライザー g. ヒート シンクまたはヒート シンクダミー h. プロセッサまたはプロセッサダミー i. メモリー モジュールとメモリー モジュールのダミーカード j. ネットワーク ドーター カード k. 冷却ファン アセンブリー l. 冷却エアフローカバー(取り付けられている場合) m. 電源供給ユニット n. プロセッサ拡張モジュール(該当する場合) 3.
メモ: サービス タグ(サービス タグ)フィールドが空白の場合のみ、サービス タグを入力できます。正しいサービス タグを 入力してください。一度サービス タグが入力されると、更新または変更できません。 5. OK をクリックします。 6. 新規または既存の iDRAC Enterprise ライセンスをインポートします。 詳細については、www.dell.com/poweredgemanuals で Integrated Dell Remote Access Controller ユーザーズ ガイドを参照してくだ さい。 簡易復元機能を使用したサービスタグの復元 簡易復元機能を使用すると、システム基板を交換した後もお使いのサービスタグ、ライセンス、UEFI 構成、およびシステムの設定 データを復元できます。すべてのデータは自動的にバックアップフラッシュデバイスに自動的にバックアップされます。BIOS が バックフラッシュデバイスで新しいシステム基板とサービスタグを検知したら、BIOS がユーザーにバックアップ情報を復元するプ ロンプトを表示します。 手順 1.
手順 1. システム ボードの TPM コネクタの位置を確認します。 メモ: システム基板上の TPM コネクタを見つけるには、「システム基板コネクタ」の項を参照してください。 2. TPM のエッジコネクタを TPM コネクタのスロットの位置に合わせます。 3. プラスチック製のリベットがシステム ボードのスロットに合うように、TPM を TPM コネクタに挿入します。 4. 所定の位置に収まるまでプラスチック製のリベットを押します。 図 95. TPM の取り付け 1. システム基板上のリベットスロット 3. TPM 2. プラスチック製リベット 4. TPM コネクター 次の手順 1. システム ボードを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 安全にお使いいただくために 、p. 65 関連タスク システム内部の作業を始める前に 、p. 66 システム ボードの取り付け 、p. 160 システム内部の作業を終えた後に 、p.
3. TPM Security(TPM セキュリティ)オプションで、 On with Pre-boot Measurements(起動前測定でオン)を選択します。 4. TPM Command(TPM コマンド)オプションで、Activate(アクティブ化)を選択します。 5. 設定を保存します。 6. システムを再起動します。 7. System Setup(セットアップユーティリティ)を再起動します。 8. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > System Security Settings(システムセキュリティ設定) をクリックします。 9.
7 システム診断プログラムの使用 システムに問題が起こった場合、デルのテクニカルサポートに電話する前にシステム診断プログラムを実行してください。システ ム診断プログラムを使うと、特別な装置を使用せずにシステムのハードウェアをテストでき、データが失われる心配もありません。 お客様がご自分で問題を解決できない場合でも、サービスおよびサポート担当者が診断プログラムの結果を使って問題解決の手助 けを行うことができます。 メモ: OEM 診断イベント メッセージの詳細については、『Event and Error Message Reference Guide for 13th Generation Dell PowerEdge Servers Version 1.
2.
8 ジャンパとコネクタ トピック: • • • システム基板のジャンパ設定 システム ボード コネクター パスワードを忘れたとき システム基板のジャンパ設定 表 36.
図 96. システム ボード コネクター 表 37.
表 37.
表 38. プロセッサ拡張モジュールコネクタと説明 アイテム コネクター 説明 1 D3. D7、D11、D4、D8、D12 メモリモジュールソケット 2 CPU4 プロセッサソケット 4 3 D10、D6、D2、D9、D5、D1 メモリモジュールソケット 4 CPU3 プロセッサソケット 3 5 C10、C6、C2、C9、C5、C1 メモリモジュールソケット 6 C3、C7、C11、C4、C8、C12 メモリモジュールソケット パスワードを忘れたとき システムのソフトウェアセキュリティ機能として、システムパスワードとセットアップパスワードがあります。パスワードジャンパ を使用すると、パスワード機能を有効または無効にしたり、現在使用中の任意のパスワードをクリアしたりすることができます。 前提条件 手順 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを取り外します。 3. システム基板ジャンパ上のジャンパを 4 および 6 番ピンから 2 および 4 番ピンに動かします。 4.
9 システムのトラブルシューティング ユーザーとシステムの安全優先 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: ソリューションの検証は工場出荷のハードウェア構成を使用して行われています。 トピック: • • • • • • • • • • • • • • • • • • • • • • • • システムの起動エラーのトラブルシューティング 外部接続のトラブルシューティング ビデオサブシステムのトラブルシューティング USB デバイスのトラブルシューティング iDRAC ダイレクト(USB XML 設定)のトラブルシューティング iDRAC ダイレクト(ノートパソコン接続)のトラブルシューティング シリアル入出力デ
● システムの仕様詳細と外付けデバイスを比較して互換性を確認します。 ● デバイスが正常に作動していることを確実にするため、他の同様のシステムで外部デバイス機能を確認します。 ● システム ポートが正常に作動していることを確実にするため、他の同様の外部デバイスでこのシステムを確認します。 さらにクエリーがある場合は、グローバル テクニカル サポートに連絡してください。 ビデオサブシステムのトラブルシューティング 前提条件 メモ: iDRAC グラフィカル ユーザー インターフェイス(GUI)の仮想コンソール内のローカル サーバー ビデオ有効オプションが 選択されていることを確認してください。このオプションが選択されていない場合、ローカル ビデオは無効になっています。 メモ: VGA ポートは、ホットプラグ非対応です。 手順 1. モニタへのケーブル接続(電源とディスプレイ)を確認します。 2.
9. キーボードが機能している場合は、セットアップユーティリティを起動します。Integrated Devices(内蔵デバイス)画面で、 すべての USB ポートが有効化されていることを確認します。キーボードが機能していない場合は、リモート アクセスを使用し て USB オプションを有効または無効にします。 10. USB 3.0 がセットアップ ユーティリティで有効になっているかどうかを確認します。有効な場合は無効にして、システムを再起 動します。 11. システムにアクセスできない場合は、システム内部の NVRAM_CLR ジャンパをリセットし、BIOS をデフォルト設定に戻しま す。「システム ボードのジャンパ設定」の項を参照してください。 12. IDRAC Settings Utility で、USB Management Port Mode が Automatic または Standard OS Use として設定されていること を確認してください。 13. 各 USB デバイスを一度に 1 台ずつ再接続し、電源を入れます。 14.
iDRAC ダイレクト(ノートパソコン接続)のトラブルシ ューティング USB ノートパソコン接続とシステム設定の詳細については、www.dell.com/poweredgemanuals の『Integrated Dell Remote Access Controller ユーザーズ ガイド』を参照してください。 手順 1. ノートパソコンが前面 USB 管理ポートに接続されていることを確認します。これは USB Type A/A ケーブルを使用する、 のアイコンで識別されます。 2. iDRAC Settings Utility(iDRAC 設定ユーティリティ)画面で、USB Management Port Mode(USB 管理ポートのモード)が、 Automatic(自動)または iDRAC Direct Only(iDRAC Direct のみ)に設定されていることを確認します。 3. ノートパソコンで、Windows オペレーティング システムが実行されている場合は、iDRAC 仮想 USB NIC デバイス ドライバーが インストールされていることを確認します。 4.
2. システムを再起動し、NIC コントローラーに関するシステム メッセージがないかチェックします。 3. NIC コネクタの該当するインジケータを確認します。 ● リンクインジケータが点灯しない場合は、ケーブルの接続が外れている可能性があります。 ● アクティビティインジケータが点灯しない場合は、ネットワークドライバーファイルが損傷しているか、欠落している可能 性があります。必要に応じて、ドライバーをインストールまたは交換します。詳細については、NIC のマニュアルを参照し てください。 ● 別の正常なネットワーク ケーブルを試してください。 ● 問題が解決しない場合は、スイッチまたはハブ上の別のコネクタを使用してください。 4. 適切なドライバーがインストールされ、プロトコルがバインドされていることを確認します。詳細については、NIC のマニュア ルを参照してください。 5. セットアップユーティリティを起動し、内蔵デバイス 画面で NIC ポートが有効になっていることを確認します。 6.
5. 手順 3 で取り外した拡張カード以外のコンポーネントを再度取り付けます。 6. システム カバーを取り付けます。 7. システムと接続されている周辺機器の電源を入れます。 問題が解決しない場合は、「困ったときは」の項を参照してください。 8. システムが正常に起動する場合は、システムの電源を切り、取り外した拡張カードをすべて再度取り付けます。 9. 適切な診断テストを実行します。詳細については、「システム診断プログラムの実行」の項を参照してください。 次の手順 テストに失敗した場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p. 188 システム診断プログラムの使用 、p.
システム バッテリーのトラブルシューティング 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: システムの電源が長い期間(数週間から数か月)切られていた場合、NVRAM からシステム設定情報が失われる可能性が あります。この状態は不良バッテリが原因で発生します。 メモ: 一部のソフトウェアには、システムの時刻を進めたり遅らせたりするものがあります。システム セットアップによって 設定された時刻以外はシステムが正常に作動しているように見える場合、問題の原因はバッテリーの欠陥ではなく、ソフトウ ェアにあると考えられます。 手順 1. セットアップユーティリティで時刻と日付を再入力します。 2.
3. 接続が緩んでいないことを確認します。 たとえば、電源ケーブルの接続が緩んでいることがあります。 4. 電源が適用規格を満たしていることを確認します。 5. 回路のショートがないことを確認します。 6. 適切な資格を持つ電気技術者に電圧線をチェックしてもらい、必要な仕様を満たしていることを確認します。 タスクの結果 メモ: 電源供給ユニットによっては、定格容量を実現するために、AC 200~240V が必要になる場合があります。詳細について は、www.dell.com/poweredgemanuals にある『インストールおよびサービス マニュアル』の「システム仕様詳細」の項を参照して ください。 電源供給ユニット問題のトラブルシューティング 手順 1. 接続が緩んでいないことを確認します。 たとえば、電源ケーブルの接続が緩んでいることがあります。 2. 電源供給ハンドル LED に、電源供給が正常に機能していると表示されていることを確認します。 3. 最近システムをアップグレードした場合は、電源供給ユニットに新しいシステムをサポートするのに十分な電力があることを確 認してください。 4.
RACADM コマンドを使用する場合: 1. racadm help system.thermalsettings コマンドを実行します 詳細については、www.dell.com/poweredgemanuals の『Integrated Dell Remote Access ユーザーズ ガイド』を参照してください 冷却ファンのトラブルシューティング 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: ファンの番号は、システム管理ソフトウェアで参照できます。特定のファンに問題が発生した場合に、冷却ファン アセ ンブリー上のファンの番号をメモしておくことで、簡単に識別して交換することができます。 1.
4. セットアップユーティリティを起動して、システムメモリーの設定を確認します。必要に応じてメモリ設定を変更します。 メモリの設定が取り付けられているメモリと一致しているにもかかわらず、引き続きエラーメッセージが表示される場合は、手 順 12 に進みます。 5. システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 6. システム カバーを取り外します。 7. メモリチャネルをチェックし、正しく装着されていることを確認します。 メモ: 障害が発生したメモリー モジュールの位置については、システム イベント ログまたはシステム メッセージを参照し てください。メモリデバイスを取り付けなおします。 8. ソケットに装着されている各メモリモジュールを抜き差しします。 9. システム カバーを取り付けます。 10. セットアップユーティリティを起動して、システムメモリーの設定を確認します。 問題が解決しない場合は、手順 11 に進みます。 11. システム カバーを取り外します。 12.
次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連概念 セットアップユーティリティ 、p. 34 関連参照文献 ヘルプ 、p. 188 システム ボード コネクター 、p. 168 関連タスク システムカバーの取り外し 、p. 68 microSD カードのトラブルシューティング 前提条件 メモ: 特定の micro SD カードには、カードに物理的な書き込み保護電源があります。書き込み保護スイッチがオンになってい る場合は、micro SD カードに書き込みできません。 メモ: IDSDM スロットおよび vFlash スロットは、ホットプラグ非対応です。 手順 1. セットアップユーティリティを起動し、内蔵 SD カードポートが有効になっていることを確認します。 2. システムおよび接続されている各種周辺機器の電源を切り、システムをコンセントから外します。 3.
手順 1. 別の CD または DVD を使用してみます。 2. 問題が解決しない場合は、セットアップユーティリティを起動して、内蔵 SATA コントローラとドライブの SATA ポートが有効 であることを確認します。 3. 適切な診断テストを実行します。 4. システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 5. ベゼルが取り付けられている場合は、取り外します。 6. システム カバーを取り外します。 7. インタフェースケーブルが光学ドライブおよびコントローラにしっかり接続されていることを確認します。 8. 電源ケーブルがドライブに正しく接続されていることを確認します。 9. システム カバーを取り付けます。 次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p.
ドライブまたは SSD のトラブルシューティング 前提条件 注意: このトラブルシューティング手順により、ドライブに保存されたデータが削除されるおそれがあります。続行する前に、 ドライブ上のすべてのファイルをバックアップしてください。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 Diagnostics(診断)テストの結果に応じて、随時次の手順を実行します。 2. システムに RAID コントローラーが搭載され、お使いのドライブが RAID アレイに設定されている場合は、次の手順を実行しま す。 a.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 拡張カードが、取り付けガイドラインに従って取り付けられていることを確認します。 各拡張カードがコネクタに確実に装着されていることを確認します。 システム カバーを取り付けます。 システムをコンセントに再接続し、システムと接続されている周辺機器の電源を入れます。 問題が解決しない場合は、システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 システム カバーを取り外します。 システムに取り付けられている拡張カードをすべて取り外します。 システム カバーを取り付けます。 システムをコンセントに再接続し、システムと接続されている周辺機器の電源を入れます。 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 テストに失敗した場合は、「困ったときは」の項を参照してください。 14. 手順 10 で取り外した各拡張カードについて、次の手順を実行します。 a. b. c. d. e.
b. c. d. e. システム カバーを取り外します。 拡張カードの 1 枚を取り付けなおします。 システム カバーを取り付けます。 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p. 188 システム診断プログラムの使用 、p. 166 プロセッサーのトラブルシューティング 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: プロセッサー ソケットはホットプラグ対応ではありません。 手順 1.
診断メッセージ お使いのシステムで診断テストを実行したときにエラーが検出された場合、システム診断ユーティリティによりメッセージが生成さ れます。システム診断プログラムの詳細については、システム ファームウェアおよびシステム コンポーネントを監視するエージェ ントにより作成されたイベントおよびエラー メッセージの詳細については、qrl.dell.
10 ヘルプ トピック: Dell EMC へのお問い合わせ マニュアルのフィードバック QRL によるシステム情報へのアクセス • • • Dell EMC へのお問い合わせ Dell EMC では、オンラインおよび電話によるサポートとサービス オプションをいくつかご用意しています。お使いのコンピュータ ーがインターネットに接続されていない場合は、購入時の納品書、出荷伝票、請求書、または Dell EMC 製品カタログで連絡先をご 確認ください。これらのサービスは国および製品によって異なり、お住まいの地域では一部のサービスがご利用いただけない場合 があります。Dell EMC のセールス、テクニカル サポート、またはカスタマー サービスへは、次の手順でお問い合わせいただけます。 手順 1. www.dell.com/support/home にアクセスします。 2. お住まいの国を、ページ右下隅のドロップダウンメニューから選択します。 3. カスタマイズされたサポートを利用するには、次の手順に従います。 a. サービス タグを入力します フィールドに、お使いのシステムのサービス タグを入力します。 b.
● テクニカルサポートや営業チームへのお問い合わせのためのデルへの直接的なリンク 手順 1. www.dell.com/qrl にアクセスして、お使いの製品に移動する、または 2.